Piriform fossa and/or esophageal injuries caused by calibration tubes are relatively rare and re-main unelucidated. Herein, we report the case of a 36-year-old woman with morbid obesity, sleep apnea, and menstrual abnormalities who was scheduled to undergo laparoscopic sleeve gastrectomy (LSG). We inserted a 36-Fr Nelaton catheter made of natural rubber as a calibration tube during the surgery. However, excessive resistance was observed. We confirmed a submuco-sal layer detachment of approximately 5 cm from the left piriform fossa to the esophagus using intraoperative endoscopy. Additionally, LSG was performed using an endoscope as the guiding calibration tube. We inserted a nasogastric tube under endoscopy with a guidewire before com-pleting the surgery, hoping for a guiding effect on saliva flow. After 17 months, the patient suc-cessfully lost weight postoperatively without complaints of neck pain or discomfort during swallowing. Therefore, if the damage is limited to the submucosal layer, as in this case, conserva-tive therapy should be considered, which is similar to the concept of not requiring suture closure in endoscopic submucosal dissection. This case highlights the risk of iatrogenic injuries to the pi-riform fossa and/or esophagus during LSG and the importance of careful calibration tube inser-tion to prevent them.

This study focuses on calibrating the linear Drucker-Prager yield criterion for polypropylene under multiaxial loading conditions, using the Arcana machine to achieve a wide range of triaxiality states. The Drucker-Prager criterion has been adapted for polymers, composites, and metals due to its ability to account for the influence of hydrostatic pressure on yield stress. This study employs the Arcana machine, which allows for testing flat plate samples under various angles, thereby simulating different stress states from pure shear to biaxial tension. Additionally, uniaxial compression tests were conducted to extend the range of triaxiality. The material used in this study is Sabic 83MF10, a polypropylene polymer. Samples were prepared by injection molding and cut to specific dimensions. Tests were performed using a universal testing machine with the Arcana handle, and the results were analyzed to determine the yield strength, pressure, and triaxiality for each sample. The results showed a linear relationship between von Mises stress and hydrostatic pressure, with a friction angle (β) of 20.65° and material cohesion (d) of 27.81. The numerical simulations in Abaqus confirmed the validity of the Drucker-Prager model, accurately reflecting the moment of yielding for the tested samples.

Accurate traffic simulation models play a crucial role in developing intelligent transport systems that offer timely traffic information to users and efficient traffic management. However, calibrating these models to represent real-world traffic conditions accurately poses a significant challenge due to the dynamic nature of traffic flow and the limitations of traditional calibration methods. This article introduces a machine learning-based approach to calibrate macroscopic traffic simulation models using real-time traffic video stream data. By leveraging computer vision technologies to extract key traffic parameters from video streams, the approach demonstrated a notable improvement in aligning the generated data from the calibrated simulation model with car sensor data, achieving an average improvement of over 50% compared to the uncalibrated macroscopic model. Moreover, there was a substantial reduction in data drift for the machine learning model integrated into the virtual transport space using vehicle-to-everything technology, resulting in a more than fourfold decrease in the average absolute error of the model.

The satellite Earth observation (EO) sector is burgeoning with hundreds of commercial satellites being launched each year, delivering a rich source of data that could be exploited for societal benefit. Data streams from the growing constellation of commercial satellites are of variable quality, limiting the potential for their combined use in science applications that need long time-series data from multiple sources. The quality of calibration performed on optical sensors onboard many satellite systems is highly variable due to calibration methods, sensor design, mission objective, budget, or other operational constraints. A small number of currently operating well-characterised satellite systems with onboard calibration, such as Landsat-8/9, Sentinel-2, and planned future missions like the NASA Climate Absolute Radiance and Refractivity Observatory (CLARREO) Pathfinder, the European Space Agency (ESA) Traceable Radiometry Underpinning Terrestrial and Helio Studies (TRUTHS), and LIBRA from China, are considered benchmarks for optical data quality due to their traceability to international measurement standards. This paper describes the concept of a space-based transfer calibration radiometer called the Satellite Cross-Calibration Radiometer (SCR) that would enable the calibration parameters from satellites such as Landsat-8/9, Sentinel-2, or other benchmark systems to be transferred to a range of commercial optical EO satellite systems while in orbit. A description of the key characteristics of the SCR to successfully operate in orbit and transfer calibration from Reference systems to Client systems is presented. A system like the SCR in orbit could complement SI-Traceable satellites (SITSats) to improve data quality and consistency and facilitate the interoperable use of data from multiple optical sensor systems for delivering higher returns on the global investment in EO.

Background Patients with severe dysphagia are usually fed using a nasogastric tube (NGT). Many patients who receive long-term NGT feeding are unable to obtain sufficient nutrients orally immediately after NGT removal. Thus, a transitional period involving oral diet training is required to transition from NGT feeding to exclusive oral feeding. We aimed to investigate the therapeutic effect of oral diet training in indwelling NGT patients with prolonged dysphagia. Methods A total of 175 patients who were fed using an NGT for more than 4 weeks were enrolled. Their swallowing function was evaluated by a videofluoroscopic swallowing study (VFSS). During the VFSS, patients received thick and thin barium while the NGT was insulted. Then, the patients underwent a VFSS without an NGT thirty minutes after NGT removal. If a patient had no aspiration with NGT inserted during the VFSS, oral diet training combined with NGT feeding was recommended. Results Of the 49 indwelling NGT patients who were recommended to receive oral diet training, 39 (79.6%) transitioned to exclusive oral feeding. A transition period of 2-8 weeks was required for them to achieve full oral feeding. Patients who were eligible for oral feeding trials showed no significant aspiration during the VFSS with an NGT inserted and had sufficient cough function. Patients who required prolonged NGT feeding and who could not complete oral trials showed significant aspiration during the VFSS when an NGT was inserted. Conclusion This study demonstrated that oral diet training combined with NGT feeding was safe in patients with prolonged dysphagia who had sufficient cough function and no aspiration during VFSS. We suggest that if the patient is a proper candidate for NGT removal, direct oral feeding training with an NGT inserted could be a useful therapeutic strategy during the transitional period from long-term NGT feeding to successful oral feeding.

Expansion tube is ideal energy absorber which dissipates kinetic energy through plastic deformation and friction. There is an urgent need to understand the influence of key parameter, e.g. semi angle, tube material, and friction coefficient, on the mechanical response and energy absorption characteristics of expansion tube. In the present work, the material properties of the tubes were tested under quasi-static loading condition, and the numerical simulations were carried out by using commercial software ABAQUS. Based on the validated finite element simulation, all the semi angle, tube material, and friction have significant effects on the energy absorption capacity of expansion tube. The expansion tube with high tensile stress of parent material have high energy absorption capacity, while the specific energy absorption is linear with the tensile stress/density of tube material. This work would give a guidance to the structural design and parent materials selection for expansion tubes.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

European Union (EU) regulations on in vitro diagnostics (IVD) and on serious cross-border threats to health provide for the establishment of European Reference Laboratories (EURLs) and their harmonisation and cooperation with National Reference Laboratories (NRLs). While the EURLs under the IVD Regulation will be operational by 1 October 2024, the EURLs under the Regulation on serious cross-border threats to health will be operational by January 2025. Although NRLs may have been operating for a long time on the basis of national legislation, they should now cooperate with each other and with EURLs in a network of centres of excellence for the authorisation and post-market surveillance of IVDs and for the epidemiological surveillance and control of communicable diseases. The term "reference laboratory" has long been used colloquially to refer to many kinds of laboratories, regardless of their tasks, competencies, responsibilities and designation. To clarify the roles and functioning of EURLs and NRLs, we evaluated the relevant current EU provisions and compared the findings with those of reference laboratories designated by other organisations, calibration (reference) laboratories and referral laboratories, which are simply referred to as "reference laboratories".

The speed-density or flow-density relationship is a fundamental aspect of traffic flow theory. Single-regime models often face challenges in consistently fitting empirical data under diverse traffic conditions. This paper addresses the inaccuracies of single-regime models, attributing them not only to their functional forms but also to data dispersion and sample selection bias. To mitigate these issues, the data is segmented into day and night periods, leading to the creation of separate models for each. Calibration results, conducted on data from two freeways, Tehran-Karaj and Tehran-Qom, reveal distinct challenges, with the former exhibiting high dispersion and the latter showing low dispersion. Surprisingly, single-regime models demonstrate notable effectiveness when applied to distinct day and night data. Further analysis, categorizing data into day and night, results in reduced errors (20-60% improvement in R-Square), emphasizing the potential for enhanced accuracy by considering distinct regimes. Overall, the study underscores the significance of regime-specific considerations for accurate traffic flow modeling. Upon thorough evaluation, the study highlights the superiority of the neural network Multi-layer Perceptron (MLP) over traditional models. The research discusses the implications of incorporating day and night parameters into the models, emphasizing their potential for accuracy enhancement.

This longitudinal study examined the development of executive function and calibration accuracy in pre-adolescents. Two hundred sixty two students(127 females) from grades 4 (n = 91), 5 (n = 89) and 6 (n = 82) took measures of executive function and performance calibration in a sport task, three times within a period of 20 months. A latent growth curve modeling analysis showed a significant relation between the rates of change of executive function and calibration. Further, the results showed a dynamic interplay in the development of executive function and calibration. There were significant inter-individual differences in the estimated population means both in executive function and calibration and in the rate of change of executive function, but not in the rate of change for calibration. The age of the participants had a positive effect only on the estimated population mean of executive function.

The success of deep learning (DL) in offline brain-computer interfaces (BCIs) has not yet translated into efficient online applications. This is due to three primary challenges. First, most DL solutions are designed for offline decoding, making the transition to online decoding complex and unclear. Second, the use of sliding windows in online decoding increases the computational complexity of DL training. Third, DL models typically require large amounts of training data, which are often scarce in BCI applications. To address these issues and enable real-time decoding, even across different subjects without calibration data, we first introduce a novel approach called real-time adaptive pooling (RAP). RAP modifies the pooling layers of existing offline DL models towards the online decoding requirements. Additionally, it significantly reduces the computational demand during training by jointly decoding consecutive windows. To reduce the amount of training data required, our approach leverages different levels of domain adaptation. We show how different settings enable different adaptation solutions. The results demonstrate that our approach is both powerful and can be calibration-free, providing a robust and practical solution for real-time BCI applications. These findings pave the way for the development of co-adaptive and highly efficient DL-based online BCI systems.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

Uterine tube extracellular matrix is a key component that regulates tubal tissue physiology, and it has a region-specific structural distribution, which are directly associated to their functions. Considering this, application of biological matrices in culture systems is an interesting strategy to develop biomimetic tubal microenvironments and enhance their complexity. However, there are no established protocols to produce tubal biological matrices that consider the organ morphophysiology for such applications. Therefore, this study aimed to establish region-specific protocols to obtain decellularized scaffolds derived from porcine infundibulum, ampulla, and isthmus to provide suitable sources of biomaterials for tissue-engineering approaches. Porcine uterine tubes were decellularized in solutions of 0.1% SDS and 0.5% Triton X-100. Decellularization efficiency was evaluated by DAPI staining and DNA quantification. We analyzed ECM composition and structure by optical and scanning electronic microscopy, FTIR and Raman spectroscopy. DNA and DAPI assays validated the decellularization, presenting significative reduction of cellular content. Structural and spectroscopy analyses revealed that produced scaffolds remained well structured and with ECM composition preserved. YS and HEK293 cells were used to attest cytocompatibility, allowing cell survival and successful interaction with the scaffolds. These results suggest that such matrices are applicable for future biotechnological approaches in the reproductive field.

As part of the Copernicus programme of the European Union (EU), the European Space Agency (ESA) has developed and is currently operating the Sentinel-2 mission that is acquiring high spatial resolution optical imagery. This paper provides a description of the calibration activities and the current status of the mission products validation activities. Measured performances, from the validation activities, cover both Top-Of-Atmosphere (TOA) and Bottom-Of-Atmosphere (BOA) products. Results presented in this paper show the good quality of the mission products both in terms of radiometry and geometry and provide an overview on next mission steps related to data quality aspects.

The monitoring of coastal waters using satellite data, from sensors including Sentinel-3 OLCI, has become a vital tool in the management of these water environments; especially when it comes to improving our understanding of the effects of climate change on these regions. In this study, Level-2 water products derived from different OLCI Sentinel-3 processors were validated against a comprehensive in situ dataset from the NW Baltic Sea proper region. The products validated were those of the regionally adapted Case-2 Regional Coast Colour (C2RCC) OLCI processor (v1.0 and v2.1), as well as the latest standard Level-2 OLCI case 2 (Neural Network) products from Sentinel-3’s processing baseline: Baseline Collection 003 (BC003), including “CHL_NN”, “TSM_NN”, and “ADG443_NN”. Furthermore, the effect of the current EUMETSAT system vicarious calibration (SVC) on the Level-2 water products was also validated. Results showed that the system vicarious calibration (SVC) reduces the reliability of the Level-2 OLCI products. For example, the application of these SVC gains to the OLCI data for the regionally adapted v2.1 C2RCC products resulted in RMSD increases of 36% for “conc_tsm”; 118% for “conc_chl”; 33% for “iop_agelb”; 50% for “iop_adg”; and 10% for “kd_z90max” using a ±3h validation window. The findings indicate that the current EUMETSAT SVC gains should be applied and interpreted with caution in the region of study at present. A key outcome of the paper recommends the development of a regionally specific SVC against AERONET-OC data for the region.

Previous camera self-calibration methods have exhibited certain notable shortcomings. On one hand, they either exclusively emphasized scene cues or solely focused on vehicle-related cues, resulting in a lack of adaptability to diverse scenarios and a limited number of effective features. Furthermore, these methods either solely utilized geometric features within traffic scenes or exclusively extracted semantic information, failing to comprehensively consider both aspects. This limited the comprehensive feature extraction from scenes, ultimately leading to a decrease in calibration accuracy. Additionally, conventional vanishing point-based self-calibration methods often required the design of additional edge-background models and manual parameter tuning, thereby increasing operational complexity and the potential for errors. Given these observed limitations, and in order to address these challenges, we propose an innovative roadside camera self-calibration model based on the Transformer architecture. This model possesses a unique capability to simultaneously learn scene features and vehicle features within traffic scenarios while considering both geometric and semantic information. Through this approach, our model can overcome the constraints of prior methods, enhancing calibration accuracy and robustness while reducing operational complexity and the potential for errors. Our method outperforms existing approaches on both real-world dataset scenarios and publicly available datasets, demonstrating the effectiveness of our approach.

Fluxgate magnetometers require calibration methods appropriate to their application levels and particularities; however the development of fully controlled calibration procedures presents a particular challenge regarding the inevitable influence of the local geomagnetic field and other external interferences when a laboratory with magnetically shielded walls is not available. In that context, we discussed the development of an automated calibration method for fluxgate magnetometers, considering those limitations in time and space, and avoiding some of the problems commonly found in other proposed solutions for the same challenge. For this task, we designed and built a new set of high level procedures, electronic systems and software, which perform active testing and automated calibration of fluxgate magnetometers, considering some resource constraints and employing instruments commonly found in electronic calibration laboratories.

Proper calibration of eye movement signal registered by an eye tracker seems to be one of the main challenges in popularizing eye trackers as yet another user input device. Classic calibration methods taking time and imposing unnatural behavior of users have to be replaced by intelligent methods that are able to calibrate the signal without conscious cooperation with users. Such an implicit calibration requires some knowledge about the stimulus a person is looking at and takes into account this information to predict probable gaze targets. The paper describes one of the possible methods to perform implicit calibration: it starts with finding probable fixation targets (PFTs), then uses these targets to build a mapping - probable gaze path. Various possible algorithms that may be used for finding PFTs and mapping are presented in the paper and errors are calculated utilizing two datasets registered with two different types of eye trackers. The results show that although for now the implicit calibration provides results worse than the classic one, it may be comparable with it and sufficient for some applications.

A membrane ozonation contactor was built to investigate ozonation using tubular membranes and to inform computational fluid dynamics (CFD) studies. Non-porous tubular polydimethylsiloxane (PDMS) membranes of 1.0 – 3.2 mm inner diameter were tested at ozone gas concentrations of 110 – 200 g m−3 and liquid side velocities of 0.002 m s−1 – 0.226 m s−1. The dissolved ozone concentration could be adjusted to up to 14 mg O3 L−1 and increased with decreasing membrane diameter and liquid side velocity. Experimental mass transfer coefficients and molar fluxes of ozone were 1.1∙10−5 mol m−2 s−1 and 2.4∙10−6 m s−1, respectively, for the smallest membrane. CFD modelling could predict the final ozone concentrations but slightly overestimated mass transfer coefficients and molar fluxes of ozone. Model contaminant degradation experiments and UV absorption measurements of ozonated water samples in both ozone (O3) and peroxone (H2O2/O3) reaction systems in pure water, river water, wastewater effluent and solutions containing humic acid show that the contactor system can be used to generate information on the reactivity of ozone with different water matrices. Combining simple membrane contactors with CFD allows predicting ozonation performance under a variety of conditions leading to improved bubble-less ozone systems for water treatment.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

This study presents a novel kinematic tracking model, designed for a networked exoskeleton system that is asynchronously taught by a remote therapist. On the server side, the therapist’s rehabilitation exercises are quantitatively assessed using a monocular passive vision system. The resultant analytical metrics are then transmitted asynchronously over the network to patients equipped with exoskeletons. On the client side, the exoskeleton utilizes these analytical metrics as reference paths for exercises, complemented by electromyography (EMG) feedback. This work introduces a calibration approach aimed at estimating angular positions by utilizing EMG observations. The calibration model establishes real-time correlations between polynomial reference positions. This calibration mechanism is integrated into simulations of both upper and lower limb exoskeletons. We further explore redundant kinematics, incorporating an EMG observer for linear, time-variant rehabilitation tracking control. Our methodology is validated using vision-based metric data and experimental EMG measurements for various exercises, including shoulder flexion, elbow flexion, and rowing-like movements. This work also includes computer simulations for tracking the control of rehabilitation exercises, demonstrating the adaptability of the system in reliably, robustly, and effectively following desired trajectories.

In this study, Acısu Basin, which is upper side of one of the most important basins (Gediz) in Türkiye, was modelled using three types of hydrological models and three different calibration algorithms. Lumped (GR4J), semi-distributed (SWAT+), and fully distributed (mHM) hydrological models were built and integrated with Parameter Estimation Tool (PEST) which is a model independent calibration tool including various algorithms. Levenberg Marquardt (L-M), Shuffled Complex Evolution (SCE), and Covariance Matrix Adoption Evolution Strategy (CMA-ES) were selected as calibration algorithms. Calibration period was 1991-2000, and validation results were obtained for 2002-2005. The effect of model structure and calibration algorithm selection on discharge simulation was evaluated via comparison of 9 different model-algorithm combinations. Results have shown that mHM and CMA-ES combination showed the best discharge simulation performance according to NSE values (calibration: 0.67, validation: 0.60). Although statistically the model results were classified as acceptable, the pattern comparison of discharge value shows that all of the models miss the peak values in significant amounts. This problem may be related to the interventions made in 2000-2001 years interval and possible to overcome by changing the calibration and validation periods, increasing the number of iterations or using the naturalized gauge data.

The Kennedy model offers a robust framework for modeling forward rates, leveraging Gaussian random fields to accommodate emerging phenomena such as negative rates. In our study, we employ maximum likelihood estimations to determine the parameters of the Kennedy field, utilizing Radon-Nikodym derivatives for enhanced accuracy. We introduce an efficient simulation method for the Kennedy field and develop a Black-Scholes-like analytical pricing formula for diverse financial assets. Additionally, we present a novel parameter estimation algorithm grounded in numerical extreme value optimization, enabling the recalibration of parameters based on observed financial product prices. To validate the efficacy of our approach, we assess its performance using real-world par swap rates in the latter part of this article.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

In this paper is proposed an analytical technique which can be used to obtain the forced response of a cantilevered tube conveying fluid. Considering the pipe subjected to an arbitrary harmonic force either distributed or concentrated, an analytical solution is found using Green’s function method. The solution obtained of the closed form satisfies the differential equations in a classical sense. The presented method giving the exact solutions is more precise than the classical eigenfunction expansion or Galerkin’s method with no need to the eigenfunctions or eigenvalues.

The study of ecosystems, both natural and artificial, has historically been mediated by population dynamics theories. In this framework, quantifying population numbers and related variables (associated with metabolism or biological-environmental interactions) plays a central role in measuring and predicting system-level properties. As we move towards advanced technological engineering of cells and organisms, the possibility of bioengineering ecosystems (from the gut microbiome to wildlands) opens several questions that will require quantitative models to find answers. Here, we present a comprehensive survey of quantitative modelling approaches for managing three kinds of synthetic ecosystems, sharing the presence of engineered strains. These include test tube examples of ecosystems hosting a relatively low number of interacting species, mesoscale closed ecosystems (or ecospheres), and macro-scale, engineered ecosystems. The potential outcomes of synthetic ecosystem designs and their limits will be relevant to different disciplines, including biomedical engineering, astrobiology, space exploration and fighting climate change impacts on endangered ecosystems. We propose a space of possible ecosystems that captures this broad range of scenarios and a tentative road map for open problems and further exploration.

Large-scale crowd phenomena are complex to model because the behaviour of pedestrians needs to be described at both strategic, tactical, and operational levels and is impacted by the density of the crowd. Microscopic models manage to mimic the dynamics at low densities, whereas mesoscopic models achieve better performances in dense situations. This paper proposes and evaluates a novel agent-based architecture to enable agents to dynamically change their operational model based on local density. The ability to combine microscopic and mesoscopic models for multi-scale simulation is studied through a use case of pedestrians at the Festival of Lights, Lyon, France. Pedestrian outflow data is extracted from video recordings of exiting crowds at the festival. The hybrid model is calibrated and validated using a genetic algorithm that optimizes the match between simulated and observed outflow data. Additionally, a local sensitivity analysis is then conducted to identify the most sensitive parameters in the model. Finally, the performance of the hybrid model is compared to different models in terms of density map and computation time. The results demonstrate that the hybrid model has the capacity to effectively simulate pedestrians across varied density scenarios while optimizing computational performance compared to other models.

Phylogenomics has enriched our understanding that the Tree of Life can have network-like or reticulate structures among some taxa and genes. Non-vertical modes of evolution—such as hybridization/introgression and horizontal gene transfer—deviate from a strictly bifurcating tree model, causing non-treelike patterns. Here, we present a brief overview of a phylogenomic workflow for inferring organismal histories and compare methods for detecting reticulate evolution. We discuss how the timing of coalescent events can help disentangle introgression from incomplete lineage sorting and how horizontal gene transfer events can help determine the relative timing of speciation events. In doing so, we identify pitfalls of certain methods and discuss how to extend their utility across the Tree of Life. Workflows, methods, and future directions discussed herein underscore the need to embrace reticulate evolutionary patterns for understanding the timing and rates of evolutionary events, providing a clearer understanding of life’s history.

This paper presents a calibration and thermal compensation method that aims to minimize cost and processing time while maintaining high accuracy. First, the number of positions to perform the calibration procedure is optimized, and then, based on this optimized calibration number, thermal compensation is performed, which is necessary for environments with large temperature variations, since calibration parameters change at different temperatures. The calibration procedures and algorithms were experimentally validated on marketed accelerometers. Based on the optimized calibration method, the calibrated results have been obtained nearly 100 times improvement. Thermal drift calibration experiments on the triaxial accelerometer show that the thermal compensation scheme in this paper can effectively reduce drift in the temperature range of -40°C to 60°C. The temperature drifts of x- and y-axes are reduced from -13.2 and 11.8 mg to -0.9 and -1.1 mg, respectively. The z-axis temperature drift is reduced from -17.9 to 1.8 mg. We have conducted various experiments on the proposed calibration method and demonstrated its capacity to calibrate the sensor frame error model (SFEM) parameters. Therefore, the MEMS sensors calibrated in this paper have certain engineering application values for tilt measurement.

By reinterpreting the calibration of structural models, a reassessment of the importance of the input variables is undertaken. The analysis shows that volatility is the key parameter to any calibration exercise by several orders of magnitude. In order to maximize the sensitivity to volatility, a simple formulation of Merton’s model is proposed that employs deep out-of-the-money option implied volatilities. The methodology also eliminates the use of historic data to specify the default barrier thereby leading to a full risk neutral calibration. Subsequently, a new technique for identifying and hedging capital structure arbitrage opportunities is illustrated. The approach seeks to hedge the volatility risk, or vega, as opposed to the exposure from the underlying equity itself, or delta. The results question the efficacy of the common arbitrage strategy of only executing the delta hedge.

The sugar company Valdez S.A. Entity located within the geographical limits of the city of Milagro, needs to reduce its emissions to the environment and does not always comply with the air emissions standards for stationary combustion sources, which indicates that for equipment installed before 2003 they have a maximum limit of 300 mg / m³. A mist eliminator was designed to work inside the original wet gas scrubber of the water-tube cauldron #10, which uses Bagasse as fuel, for the generation of steam for industrial use. The research is documentary and field. The methodology used was mixed. focusing on the comparison of three types of technologies to meet the objectives, the fog eliminators types: Demister, Cyclone and Chevron. To find the appropriate complement, a comparison sheet was made, which is a table of contents evaluated quantitatively, analyzing indicators formulated in each of the contents. The results, supported by the Multiple Criteria Decision Analysis methodology, select the Chevron type fog eliminator, with the best efficiency for capture. Using AutoCAD, allows to visualize in 3D, the structural design in the gas scrubber.

The idea that the Earth system self-regulates in a habitable state was proposed in the 1970s by James Lovelock, who conjectured that life plays a self-regulatory role on a planetary-level scale. A formal approach to such hypothesis was presented afterwards under a toy model known as the Daisyworld. The model showed how such life-geosphere homeostasis was an emergent property of the system, where two species with different properties adjusted their populations to the changing external environment. So far, this ideal world exists only as a mathematical or computational construct, but it would be desirable to have a real, biological implementation of Lovelock's picture beyond our one Biosphere. Inspired in the exploration of synthetic ecosystems using genetic engineering and recent cell factory designs, here we propose such a living, microbial Daisyworld. This is based on a synthetic microbial ecosystem using pH as the external, abiotic control parameter. Several case studies are considering, including two, three and multiple species assemblies. Despite that oscillatory dynamics and chaos emerge in the latter case, it is shown that global regulation is also achieved in most cases as species diversity increases. The alternative implementations and their implications of this model in other synthetic biology scenarios, including ecosystem engineering, are outlined.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

Diabetic foot is a serious complication that poses significant risks for diabetic people. The resulting reduction in protective sensitivity in the plantar region requires early detection to prevent the imminent ulceration and amputation. The primary method employed for evaluating this sensitivity loss is the 10 g f Semmes-Weinstein monofilament test, commonly used as a first-line procedure. However, the lack of calibration in existing devices often introduces decision errors due to unreliable feedback. In this paper, a new equipment designed to address these limitations and enhance the assessment of the sensitivity loss using the 10 g f monofilament is introduced. The proposed system automates metrological verification and evaluation processes, ensuring accurate and reliable results. Furthermore, it simulates the practitioner’s procedure, serving both as a valuable training tool and a means to provide force-feedback information. An analytical model of the monofilament buckling and deflection is also presented. The obtained results showed that the tested monofilaments had a very high error compared to the 10 g f declared by the manufacturers. It is aimed, by introducing this advanced equipment, to improve the precision and reliability of assessing the sensitivity loss. The integration of automated verification, simulation capabilities, and precise measurements shows great promise for diabetic patients, reducing the likelihood of adverse outcomes such as ulceration and amputation.

Multi-cameras system is widely applied in 3D computer vision especially when multiple cameras are distributed on both sides of the measured object. The calibration methods of multi-cameras system are critical to the accuracy of vision measurement and the key is to find an appropriate calibration target. In this paper, a high-precision camera calibration method for multi-cameras system based on transparent glass checkerboard and ray tracing is described, which is used to calibrate multiple cameras distributed on both sides of the glass checkerboard. Firstly, the intrinsic parameters of each camera is obtained by Zhang’s calibration method. Then, multiple cameras capture several images from the front and back of the glass checkerboard with different orientations, and all images contain distinct grid corners. As the cameras on one side are not affected by the refraction of glass checkerboard, extrinsic parameters can be directly calculated. However, the cameras on another side are influenced by the refraction of glass checkerboard, and the direct use of projection model will produce calibration error. A multi-cameras calibration method using refractive projection model and ray tracing is developed to eliminate this error. Furthermore, both synthetic and real data are employed to validate the proposed approach. The experimental results of refractive calibration show that the error of the 3D reconstruction is smaller than 0.2 mm, the relative errors of both rotation and translation are less than 0.014%, and the mean and standard deviation of reprojection error of 4-cameras system are 0.00007 and 0.4543 pixel. The proposed method is flexible, high accurate, and simple to carry out.

The high spatial complexities of soil temperature modelling over semiarid land have challenged the calibration—predication framework, whose composited objective lacks comprehensive evaluation. Therefore, this study, based on the Noah land surface model and its full parameter table, utilizes two global searching algorithms and eight kinds of objective with dimensional—varied metrics, combined with dense site soil moisture and temperature observations of central Tibet, to explore different metrics’ performances on the spatial heterogeneity and uncertainty of regional land surface parameters, calibration efficiency and effectiveness, as well as spatiotemporal complexities in surface forecasting. Results have shown that metrics’ diversity has shown greater influence on the calibration—predication framework than the global searching algorithms themselves. Besides being significantly better than other metrics, the enhanced multi objective metric (EMO) and the enhanced Kling-Gupta efficiency (EKGE) have their own advantages and disadvantages in simulations and parameters respectively. Especially, EMO that composited with four metrics as correlated coefficient, root mean square error, mean absolute error, and Nash–Sutcliffe efficiency, has shown relatively balanced performance in surface forecasting when compared to EKGE. In general, the calibration—predication framework that benefited from EMO could greatly reduce the spatial complexities in soil temperature modelling of the semiarid land.

In the early stage of new vehicle development, the requirements of maximum performance of the air conditioning (AC) system are obtained through Amesim software simulation, but the calibration control of the AC system is usually carried out in the prototype-build vehicle test stage, and the test time is spanned up to 10 months after spring (autumn), summer and winter, of which up to 2 months are for environment chamber tests. Due to the long calibration cycle of AC control in the road test, which seriously affects the vehicle launch time, virtual calibration technology of air conditioning system is developed to shorten the calibration cycle of AC systems and ensure the quality of vehicles. In the project development stage, the calibration control of the vehicle AC system can be realized to carry out the functional test of the AC system in advance. In that, the grade of maturity for the AC system control can be improved, the on-road calibration test cycle can be shortened, and the development cost can be saved.

The redshifted 21 cm line signal is a powerful probe of the cosmic dawn and the epoch of reionisation. The global spectrum can potentially be detected with a single antenna and spectrometer. However, this measurement requires an extremely accurate calibration of the instrument to facilitate the separation of the 21 cm signal from the much brighter foregrounds and possible variations in the instrument response. Understanding how the measurement errors propagate in a realistic instrument system and affect system calibration is the focus of this work. We simulate a 21 cm global spectrum observation based on the noise wave calibration scheme. We focus on how measurement errors in reflection coefficients affect the noise temperature, and how typical errors impact on the recovery of the 21 cm signal, especially in the frequency domain. Results show that for our example set up, a typical VNA measurement error in the magnitude of the reflection coefficients of the antenna, receiver, open cable which are 0.001, 0.001, 0.002 (linear) respectively would result in a 200 mK deviation on the detected signal, and a typical measurement error of 0.48∘, 0.78∘, 0.15∘ in the respective phases would cause a 40 mK deviation. The VNA measurement error can greatly affect the result of a 21 cm global spectrum experiment using this calibration technique, and such a feature could be mistaken for or be combined with the 21 cm signal.

The capacitor-mismatch among diverse defects caused by the manufacturing process variations significantly affects the linearity of capacitor-array used to implement the capacitive digital-to-analog converter (CDAC) in the successive-approximation-register (SAR) analog-to-digital converter (ADC). Accordingly, the linearity of the SAR ADC is limited by that of capacitor-array, resulting in serious yield loss. This paper proposes an efficient foreground self-calibration technique to enhance the linearity of the SAR ADCs by mitigating the capacitor-mismatch based on the split ADC architecture along with variable capacitors. In this work, two ADC channels (i.e., ADC1 and ADC2) for the split ADC architecture include their capacitive DACs (CDACs) whose binary-weighted capacitor-arrays consist of variable capacitors. A charge-sharing SAR ADC is used for each ADC channel. In the normal operation mode, their digital outputs are averaged to be the final ADC output, as in a conventional split ADC. In the calibration mode, every single binary-weighted capacitor for the two ADCs is sequentially calibrated by making parallel or/and antiparallel connection among two or thee capacitors from the two channels. For instance, because the capacitors of the CDACs ideally exhibit the binary-weighted relation as Cn=2×Cn−1, variable capacitor Cn of ADC1 can be updated to be closest to the sum of Cn−1 of ADC1 and Cn−1 of ADC2 for the calibration. For the process, the two capacitor-arrays of the two ADCs can be reconfigured to be connected to each other, so that Cn of ADC1 can be connected with two of Cn−1 of ADC1 and ADC2 in antiparallel. The two voltages at the top and the bottom plates of the CDAC are compared by a comparator of ADC1, and the comparison results are used to update Cn. This process is iterated, until Cn is in agreement with the sum of two of Cn−1. Finally, all the capacitors can be calibrated in this way to have the binary-weighted relation. The simulation results based on the proposed work with a split SAR ADC model verified that the proposed technique can be practically used, by showing that the total-harmonic-distortion and the signal-to-noise-and-distortion ratio were enhanced by 21.8-dB and 6.4-dB, respectively.

Spectral calibration consists of the calibration of wavelengths and the measurement of the instrument's spectral response function (SRF). Unlike conventional slits, the absorbed aerosol sensors (AAS) are used as a slit homogenizer, in which the spectral response function (SRF) is not a conventional Gaussian curve. To be more precise, the SRF is the convolution of the slit function of the spectrometer, the line spread function of the optical system, and the detector response function. The SRF of the slit homogenizer is a flat-topped multi-Gaussian function. Considering the convenience of fitting, a super-Gaussian function, which looks like a similar distribution to the flat-topped multi-Gaussian function, is used to fit the measured data in a spectral calibration. According to the results, the SRF’s shapes, due to the Earth port, resemble a Gaussian curve with a flatted top could be concluded, which contains an FWHM of 1.78–1.82 nm for the AAS. The results show that the correlation coefficients are about 0.99, which proves that the fitting function could better characterize the SRF of the instrument.

This paper is a response to the EPR paper titled: "Can quantum-mechanical description of physical reality be considered complete?", published in Physical Review in 1935. A quantum-mechanical (QM) measurement function describes a distribution of local results and each empirical measurement process produces one result as exact as allowed by a measuring instrument calibrated to a non-local unit standard. Repeating these empirical measurements produces a bell shaped distribution of measurement results. Each of these distributions can be compared to the other. To precisely compare a QM measurement function describing a distribution of eigenvectors to a distribution of repetitive empirical measurement results, it is necessary to determine, by calibration, the precision of the eigenvectors to the same standard as the empirical results, because each eigenvector evidences uncertainty relative to a standard. When the calibration process is recognized as formal as well as empirical, QM measurement function results and metrology measurement process results are unified.

This review paper deals with recently proposed algorithms for distributed blind macro-calibration of sensor networks based on consensus (synchronization), not requiring any fusion center. The basic algorithm, performing the estimation of the local calibration parameters, is derived commencing from appropriate local criteria, and developing the corresponding gradient descent scheme. It is shown that the estimated parameters of the calibration functions asymptotically converge, in the mean-square sense and with probability one (w.p.1), to such values that ensure consensus on calibrated sensor gains and calibrated sensor offsets. For the more realistic case in which additive measurement noise, communication dropouts and additive communication noise are present, two algorithm modifications are introduced: one using a simple compensation term, and a more robust one based on an instrumental variable. By utilizing stochastic approximation arguments it is shown that the modified algorithms also achieve asymptotic agreement for calibrated sensor gains and offsets, in the mean-square sense and w.p.1. Convergence rate is analyzed in terms of an upper bound of the mean-square error. It is also shown that the communications between nodes can be completely asynchronous, which is of substantial importance for real-world applications. Suggestions for design of \textit{a priori} adjustable weights are given. Finally, it is shown that, if there is a subset of (precalibrated) reference sensors with fixed calibration parameters, the calibrated sensor gains and offsets of the rest of the sensors do not achieve consensus - they converge to different points dictated by the reference sensors and the network characteristics. Wide applicability and efficacy of these algorithms are illustrated on several simulation examples.

In this study, the efficiencies of flat-plate and U-tube solar collectors were investigated experimentally when an Al₂O₃ nanofluid was used as a working fluid and compared to those of solar collectors using water. The energy saving and CO₂ and SO₂ generated were calculated and compared to those of solar collectors using water. In addition, based on the experimental results, an economic analysis of the use of solar collectors in various countries was performed. As the concentration of the Al₂O₃ nanofluid increased, the performance of the solar collector improved. The highest efficiency for the solar collectors was shown at the concentration of 1.0 vol% with the nanoparticle size of 20 nm. The maximum efficiencies of the flat-plate and U-tube solar collectors using 1.0 vol%-Al₂O₃ nanofluid with 20-nm nanoparticles was 74.9% and 72.4%, respectively, when the heat loss parameter was zero. The efficiencies of the flat-plate and U-tube solar collectors using Al₂O₃ nanofluid were 14.8% and 10.7 higher, respectively, than those using water. When 50 EA flat-plate solar collectors were operated for one year using Al₂O₃ nanofluid, the coal use, generated CO₂, and generated SO₂ were 189.99 kg, 556.69 kg, and 2.03 kg less than those of solar collectors using water, respectively. In addition, the largest electricity cost reduction was in Germany.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

The steady state tube furnace (SSTF) (ISO/TS 19700) was used to assess the effects altering the reaction zone of a flame had on smoke toxicity measurements. The gas inlet of the apparatus was modified to allow for a mixture of nitrogen and air to be introduced into the system. The volume of air used in each test remained at 2 L min-1 , and additional volumes of nitrogen were varied between tests altering the total volume of gas used in the primary gas inlet. The chosen conditions were representative of under-ventilated flaming by using a restricted oxygen environment. The research shows that the increase in volume flow of gas over a sample increased the smoke toxicity of the materials tested (CO and HCN). When increasing the volume of the primary air-flow through the tube furnace, the flow causes thinning of the flame zone in the apparatus and results in gaseous species spending less time in the reaction zone, resulting in less time available for chemical reactions to occur. This resulted in less complete combustion occurring, and hence an increased yield of measured products of incomplete combustion (CO and HCN), and a decreased yield of products of complete combustion (CO2).

. The impedance change of an induction coil surrounding a metal tube adapter is investigated by the truncated region eigenfunction expansion (TREE) method. Conventional TREE method is inapplicable to this problem as a consequence of the numerical overflow of eigenfunctions of the air-metal multi-subdomain regions. The difficulty is surmounted by a normalization procedure for the numerical eigenfunctions obtained from the finite element method (FEM). Efficient algorithm is devised by the Clenshaw-Curtis quadrature rule for integrals involving the numerical eigenfunctions. Numerical results of the TREE and FEM simulation coincide very well in all cases, and the efficiency of the proposed method is also confirmed.

Liquid manipulation by photoisomerization attracts recent attentions as a new active droplet control method for micro-chemical analysis. Such a non-inverse manipulation can be realized by a use of solution liquid of surfactant that exhibits the \emph{cis}-\emph{trans} isomerization triggered by light irradiation with a specific wavelength such as ultraviolet light. Since the isomerization is accompanied by changes in fluid properties, a light irradiation on one of liquid-air interfaces of a liquid column in a tube would generate differences in the wettability accompanied between the both sides of the finite liquid column. Although this technique has been demonstrated experimentally by Muto et al. (\emph{Euro.~Phys.~J.~Special Topics}, {\bf 226}, 2016, 1199--1205), its dynamics and developments of each isomer distribution are not understood. In order to reveal the liquid-column migration phenomenon, we have performed numerical simulations of air-liquid two-phase flows and its scalar transport of the isomer, using the Volume-of-Fluid method in conjunction with the Continuum-Surface-Force model and Continuous-Species-Transfer method. We validated present results by comparison with experimental result in terms of the migration distance of the liquid column. We confirmed a termination of the liquid-column migration occurs when the \emph{cis} isomer distribution reaches the non-irradiated region. The migration speed was less dependent on the liquid-column length and was proportional to the tube diameter.

Analytical methodologies were developed based on the near infrared spectroscopy (NIR) associated with chemometric tools to predict the content of macronutrients (total carbohydrate, total protein, and total lipids) in medical food. We prepared the samples employed in this study according to a mixture design with percentual variations from 25% to +25% of macronutrients. Partial least squares (PLS) regression models were built with 70 and 30 samples as calibration and validation sets, respectively. We chose the best processing techniques and results based on the parameters of the ASTM 1655 standard. The models were used to determine these macronutrients in marketed enteral nutrition products, of three different batches, that have quality certification. The average errors in the determination of total carbohydrate, total protein, and total lipids were 1.8, 4.3, and 2.3 %, respectively. The percentages of errors found in this study suggest that the developed model may be useful for the quality control laboratory routine.

Lateral vehicle control is a high importance in automated vehicles as it directly influences the vehicle’s performance and safety during operation. The Linear Quadratic Regulator (LQR) controller stands out due to its high-performance characteristics and is used in the open source for self driving functions. However, a notable limitation of the current approach is the manual calibration of LQR controllers based on the experience and intuition of the designers, leading to empirical uncertainties. To address this issue and enhance the lateral control performance, this paper concentrates on refining the LQR by employing three optimization algorithms: Artificial Bee Colony Optimization (ABC), Genetic Algorithm (GA), and Particle Swarm Optimization (PSO). These algorithms aim to overcome the reliance on empirical methods and enable a data-driven approach to LQR calibration. By comparing the outcomes of these optimization algorithms to the manual LQR controller within an offline multibody simulation as testing platform, the study highlights the superiority of the best-performing optimization approach. Following this, the optimal algorithm is implemented on a real-time system for the full vehicle level, revealing the Model-in-the-Loop and the Hardware-in-the-Loop gap up to 78,89% with lateral velocity when we use Relative Error Criterion (REC) method to validate and 2.35m with lateral displacement when considering by maximum absolute value method.

During the hand-eye calibration process of the manipulator, the Euclidean distance error of the calibration results cannot be calculated because the true values of the hand-eye conversion matrix cannot be obtained. In this paper, a new method of projection error analysis is presented. Error analysis is carried out by using a priori knowledge that the location of AR markers is fixed in the calibration process. The coordinates of the AR marker center point are reprojected to the pixel coordinate system, and then compared with the true pixel coordinates of the AR marker center point obtained by corner detection or manual labeling in order to obtain the Euclidean distance between the two coordinates as the basis for error analysis. Experimental results show that the proposed optimization method can greatly improve the accuracy of hand-eye calibration results.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

The purpose of this study is to propose a consecutive manufacturing process system to secure the productivity of excellent STKN540B steel tube in the respect of economy and safety as the supporting material for mega structures such as building, bridge and ship. The components of consecutive manufacturing are press-bending, orbital auto welding and steel tube correction. By using STKN540B a high-strength steel material with low yield point that requires a special manufacturing process unlike other steel materials, an actual tube manufacturing is carried out at each stage in this experimental study. With this, the quality of steel tube and the efficiency of the manufacturing process are analyzed to draw out some points to improve in the future.

In order to improve the performance of the draft tube in hydraulic turbine, a multi–objective optimization method for the draft tube is developed by combining the design of experiment (DOE), the radial basis function (RBF) and the non–dominated sorting genetic algorithm (NSGA–II) in this paper. The geometrical design variables of the median section in the draft tube and the cross section in its exit diffuser are considered as design parameters in this optimization, which objective function is to maximize the pressure recovery factor (Cp) and minimize the energy loss coefficient (ζ). The limited numbers of design matrix required for the shape optimization of the draft tube is generated by optimal Latin hypercube (OLH) method of the DOE technique, of which performances are evaluated through computational fluid dynamic (CFD) numerical simulation. For reducing of the computational consumption, the approximate model is used based on the RBF. The Pareto optimal solutions are finally performed using the NSGA–II for obtaining the best geometrical parameters of the draft tube. The optimization result of the draft tube shows a marked performance improvement over the original, which verifies the theoretical validity and feasibility of the proposed method in this paper.

Quantifying methane emissions is essential for meeting near-term climate goals and typically done using methane concentrations measured downwind of the source. One major source of methane that is important to observe and promptly remediate is fugitive emissions from oil and gas productions sites but installing methane sensors at the thousands of sites within a production basin is expensive. In recent years, relatively inexpensive metal oxide sensors have been used to measure methane concentrations at production sites. Current methods used to calibrate metal oxide sensors have been shown to have significant shortcomings resulting in limited confidence in methane concentrations generated by these sensors. To address this, we investigate using machine learning (ML) to generate a model that converts metal oxide sensor output to methane mixing ratios. To generate test data, two metal oxide sensors, TGS2600 and TGS2611, were collocated with a trace methane analyzer downwind of controlled methane releases. Over the duration of the measurements, the trace gas analyzer’s average methane mixing ratio was 2.40 ppm with a maximum of 147.6 ppm. The average calculated methane mixing ratios for the TGS2600 and TGS2611 using the ML algorithm were 2.42 ppm and 2.40 ppm with maximum values of 105.9 ppm and 106.3 ppm, respectively. A comparison of histograms generated using the analyzer and metal oxide sensors mixing ratios show overlap coefficients of 0.95 and 0.94 for the TGS2600 and TGS2611, respectively. Overall, our results showed there was a good agreement between the ML derived metal oxide sensors’ mixing ratios and those generated using the more accurate trace gas analyzer. This suggests that the response of lower-cost sensors calibrated using ML could be used to generate mixing ratios with precision and accuracy comparable to higher price trace methane analyzers. This would improve confidence in low-cost sensors’ response, reduce the cost of sensor deploying, and allow for timely and accurate tracking of methane emissions.

This paper presents the prelaunch radiometric calibration of the Ozone Monitor Suite - Nadir (OMS-N) instrument, a vital payload on the FY-3F satellite. FY-3F achieved a successful launch on August 3, 2023. The radiance calibration of the OMS-N instrument was achieved using an integrating sphere, with known exit radiance ascertained through a transferring radiometer. The calibration model incorporates six energy levels. The Solar Simulator Standard System was employed to validate the calibration results, selecting specific rows to represent varying spatial dimensions. Considering the influence of xenon lamp characteristic peaks and transmission errors during the calibration process, the average deviation remained within 2.3% for the UVIS channel, 3% for the UV1 channel, and 2.2% for the UV2 channel. Furthermore, this study analyzed the uncertainty of the radiometric calibration. The results indicated an absolute uncertainty of 2.32% for both UV1 and UV2 channels, while the VIS channel exhibited an uncertainty of 1.67%. The relative uncertainty was 1.84% for both UV1 and UV2 channels, with the VIS channel exhibiting an uncertainty of 1.45%. The obtained calibration coefficients are accurate and reliable and can be used for the inversion of product parameters, which is of great significance to the quantitative application of satellite data and the advancement of scientific research on quantitative remote sensing.

This study proposes self-calibration of capacitor mismatch errors for high-resolution pipeline analog-to-digital converters (ADCs). The proposed calibration circuit recursively amplifies the capacitor mismatch error by re-utilizing a multiplying digital-to-analog converter in a pipeline stage without increasing the circuit complexity, and the amplified error voltage is converted into digital code by utilizing the remaining pipeline stages. Error correction is performed by subtracting the digital code from the ADC output during normal operation. A prototype of a 12-bit pipeline ADC is fabricated in a 0.18 µm standard CMOS process. The ADC comprises eight 1.5-bit stages, followed by a 4-bit flash ADC as the final stage; the capacitor mismatch errors in the first two pipeline stages are corrected by utilizing the proposed self-calibration technique. At a sampling rate of 30 MS/s, the measured differential and integral nonlinearities improve from +0.82/-0.75 and +1.12/-1.79 to +0.45/-0.41 and +0.47/-0.91 after calibration, respectively. Further, the measured dynamic performances improve significantly with calibration. For an input frequency of 2.09 MHz, the ADC achieves a spurious-free dynamic range (SFDR) and signal-to-noise and distortion ratios (SNDR) of 69.3dB and 63.9dB before calibration, respectively. After calibration, the SFDR and SNDR increase to 84.1dB and 68.9dB, respectively, and the effective number of bits is approximately 11.1bit. The power consumption of the ADC is 35mW under 1.8V supply, and the resulting figure of merit is 514fJ/conversion step.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

The thermal properties of a building envelope are key indicators of the energy performance of the building. Therefore, methods are needed to determine quantities like U-values or heat capacitance in a fast, reliable way and with as little impact on the use of the building as possible. In this paper a technique is proposed that relies on a simplified electrical analogical model of building envelope components which can cover their dynamic thermal behavior. The parameters of this model are optimized to produce the best fit between simulated and measured outside surface temperatures. As the temperatures can be measured remotely with an infrared camera this approach requires significantly less installation effort and intrusion in the building than other methods. At the same time, a single measurement provides data for a large range of locations on a facade or a roof. The paper describes the method and a first experimental implementation of it. The experiment indicates that this method has the potential to produce results which have an accuracy that is comparable to standardized reference methods.

The Geostationary Environment Monitoring Spectrometer (GEMS) onboard the Geostationary Korean Multi-Purpose Satellite 2B was successfully launched in February 2020. GEMS is a hyperspectral spectrometer measuring solar irradiance and Earth radiance in the range of 300 to 500 nm. This paper introduces the spectral calibration algorithm for GEMS, which uses a nonlinear least-squares approach. To assess the performance of the algorithm, sensitivity tests for a series of spectral parameters such as shift, spectral range for fitting, signal-to-noise ratio, spectral response function (SRF), and reference spectrum have been conducted. To improve the assessment, a synthetic GEMS spectrum using the prelaunch GEMS SRF is adopted here. The test results show that the required accuracy (0.002 nm) is achievable for the expected uncertainties of the parameters except for the SRF and the choice of high-resolution reference spectrum, which degrade the algorithm performance by an order magnitude. To mitigate the sensitivity to SRF, retrieval of in-orbit SRF using an analytic function is suggested. Finally, a few candidates for the high-resolution solar reference spectrum are prepared for testing by the instrument during in-orbit tests.

Nacelle-based Doppler wind lidars have shown promising capabilities to assess power performance, detect yaw misalignment or perform feed-forward control. The power curve application requires uncertainty assessment. Traceable measurements and uncertainties of nacelle-based wind lidars can be obtained through a methodology applicable to any type of existing and upcoming nacelle lidar technology. The generic methodology consists in calibrating all the inputs of the wind field reconstruction algorithms of a lidar. These inputs are the line-of-sight velocity and the beam position, provided by the geometry of the scanning trajectory and the lidar inclination. The line-of-sight velocity is calibrated in atmospheric conditions by comparing it to a reference quantity based on classic instrumentation such as cup anemometers and wind vanes. The generic methodology was tested on two commercially developed lidars, one continuous wave and one pulsed systems, and provides consistent calibration results: linear regressions show a difference of ∼ 0.5 % between the lidar-measured and reference line-of-sight velocities. A comprehensive uncertainty procedure propagates the reference uncertainty to the lidar measurements. At a coverage factor of two, the estimated line-of-sight velocity uncertainty ranges from 3.2 % at 3 m s⁻¹ to 1.9 % at 16 m s⁻¹. Most of the line-of-sight velocity uncertainty originates from the reference: the cup anemometer uncertainty accounts for ∼ 90 % of the total uncertainty. The propagation of uncertainties to lidar-reconstructed wind characteristics can use analytical methods in simple cases, which we demonstrate through the example of a two-beam system. The newly developed calibration methodology allows robust evaluation of a nacelle lidar’s performance and uncertainties to be established in order to further be used for various wind turbines’ applications in confidence.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

Soil moisture plays a crucial role in various hydrological processes and energy partitioning of the global surface. The Soil Moisture Active Passive-Sentinel (SMAP-Sentinel) remote sensing technology has demonstrated a great potential in monitoring soil moisture at a scale greater than 1 km. This capability can be applied to improve weather forecast accuracy, enhance water management for agriculture, and climate-related disasters. Despite the techniques increasing used worldwide, its accuracy still requires field validation in specific regions like Thailand. In this paper, we report on extensive in-situ monitoring of soil moisture (from surface up to 1 m depth) at 10 stations across Thailand spanning the years 2021 to 2023. The aim was to validate SMAP surface soil moisture (SSM) Level 2 product over a period of two years. Using one month averaging approach, the study revealed linear relationships between the two measurement types, with the coefficient of determination (R-squared) varying from 0.13 to 0.58. Notably, areas with more uniform land use and topography such as croplands tended to have a better coefficient of determination. We also conducted detailed soil core characterization, including soil-water retention curves, permeability, porosity, and other physics properties. These soil properties were then used for estimating the correlation constants between SMAP and in-situ soil moistures using multiple linear regression. The results demonstrated R-squared values between 0.933 and 0.847. An upscaling approach of SMAP was proposed which showed a promising results when using 3-month average of all measurements in cropland together. The finding also suggest that the SMAP-Sentinel remote sensing technology exhibits significant potential for accurate soil moisture monitoring in diverse applications. Further validation efforts and research, particularly in terms of root zone depths and area-based assessments, especially in the agricultural sector, can greatly improve the technology’s effectiveness and usefulness in the region.

Placing a nasogastric tube (NGT) is a frequent nursing technique in intensive care units. The gold standard for its correct positioning is the chest X-ray due to its high sensitivity but represents a radiation source for critically ill patients. Our study aims to analyze whether the ultrasound performed by an intensive care nurse is a valid method to verify the NGT’s correct positioning and to evaluate the degree of interobserver agreement between this nurse and an intensive care physician in the NGT visualization using ultrasound. Its correct positioning was verified by direct visualization of the tube in the stomach and indirect visualization by injecting fluid and air through the tube ("dynamic fogging" technique). 23 critically ill patients participated in the study. A sensitivity of 35% was achieved using direct visualization, increasing up to 85% using indirect visualization. The degree of interobserver agreement was 0.88. Therefore, the NGT indirect visualization by an intensive care nurse using ultrasound could be a valid method to check its positioning. However, the low sensitivity obtained by direct visualization suggests the need for further training of intensive care nurses in ultrasonography. According to the high degree of agreement obtained, ultrasound could be performed by both professionals.

The reconstruction of traffic accidents has grown as an interdisciplinary field since the first accident occurred. Various methods have been developed over time, starting with primary data collected at the scene of the accident. In this work, I proposed a method by which the value of the force in the safety belt buckle can be determined when it is equipped with a pretensioning system with pyrotechnic trigger in the tube, PBP or PLP type. The anti-return system of the pretensioner mechanism, which prevents the passenger's body from moving forward, contains a set of balls that block the movement of the piston in the pretensioner tube after its activation. When limiting the movement, the force the human body exerts on the safety belt webbing is transformed into the deformation of the pretensioner tube by the balls of the anti-return system. Depending on the magnitude of the force, the marks left by the balls differ. I propose a relationship of dependence between the acting force and the deformation of the tube. An experimental test bench was created to perform shock traction tests on the pre-tensioning system, under similar conditions to those of the human body acting on the belt in case of a frontal collision. Following the tests, the force value of the seat belt buckle cable and the diameter of the spherical indentations that the balls left in the pretensioner tube were measured. A mathematical model was proposed to determine the normal force with which a ball from the anti-return system deforms the tube. The normal force was also determined by two other methods specific to contact mechanics and used in the specialized literature. By comparing the normal forces obtained by the three methods, a good correlation between the proposed mathematical model and the Komvopoulos-Ye method resulted, the "Hardness" method not being suitable for this study. The determined polynomial regression curve allows finding out the force in the cable of the closer depending on the size of the deformations produced by the balls in the tube. The forces in the belt webbing can be thus determined and biomechanics specialists can evaluate the injuries to the chest and abdomen of the occupants of a vehicle.

This study aimed to investigate the efficacy of probiotics in elderly hospitalized tube-fed patients undergoing antibiotic therapy for Clostridium difficile-associated diarrhea (CDAD). Probiotics were administered to 29 patients, with twice-daily doses for 7 days following the completion of antibiotic treatment. In the probiotic group, while stool form showed no significant change, there was a significant decrease in stool frequency. Conversely, the control group exhibited improved stool form but not frequency. The probiotic group maintained a significant difference in stool form during the follow-up period. Additionally, the control group showed a positive correlation between stool form, frequency, antibiotic therapy, and intensive care unit admission, which was not observed in the probiotic group. These findings suggest that supplementing with probiotics can effectively normalize stool form in elderly hospitalized tube-fed patients undergoing antibiotic treatment for CDAD, highlighting the potential benefits of probiotic intervention in this specific population.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

Wave propagation in buildings analyzed from its response to earthquakes can be applied for tracking the dynamic characteristics changes based on impulse response functions. The velocity of traveling shear-waves and intrinsic attenuation in buildings can be retrieved for buildings. It is an approach of importance for system identification. The Factor Building at the University of California, Los Angeles campus (henceforth referred as the UCLA Factor Building), an instrumented 15-story steel-moment frame structure, are selected for dynamic response characteristics identification. They are inferred from wave propagation using seismic interferometry for recorded motions. The deconvolved waves are used to compute shear wave travel time and wave attenuation. The natural logarithm for the envelopes of the waveforms deconvolved with the signal at the basement constrains the attenuation. The waveforms from deconvolution with the motion at the basement suggest the fundamental mode of the building. The frequency and decay with time constrain the shear velocity and attenuation as well. The velocity are measured using arrival times picked from these deconvolved waves and the average velocity is 147.1 m/s. The quality factor is equal to 10.8 with the damping ratio at 5%. The shear wave velocity and damping ratio estimated from the deconvolved waves have a good match with these inferred from the waveforms deconvolved with the basement recording. This consistency suggests that wave deconvolution can be applied to extract the building response from the excitation and ground coupling. Based on the resonant frequencies and damping ratio, the finite element model of the building is updated. This study implies that wave deconvolution is powerful to extract the building dynamic characteristics. It helps to better the understanding of the dynamic response of buildings to earthquakes.

Calibrating ecological models or making decisions with them is an optimisation problem with challenging methodological issues. Depending on the optimisation formulation, there may be a large variety of optimisation configurations (e.g. multiple objectives, constraints, stochastic criteria) and finding a single acceptable solution may be difficult. The challenges are exacerbated by the high computational cost and the non linear or elusive mathematical properties that increased with the complexity of numerical models. From the feedbacks of practitioners, the need for a guideline for conducting optimisation of complex models has emerged. In this context, we propose a practical guide for the complex model optimisation process, covering both calibration and decision-making. The guide sets out the workflow with recommendations for each step based on existing tools and methods usually scattered throughout the literature. This guide is accompanied with an ODDO template (Overview, Design, Details of Optimisation) to standardise the published description of model-based optimisation and suggests research directions.

(1) Background: Double-strand breaks (DSBs) in a single nucleus are usually measured using the sperm chromatin structure assay (SCSA), sperm chromatin dispersion (SCD) test, and comet assay (CA). We developed mono-dimensional single-cell pulsed-field gel electrophoresis (1D-SCPFGE) and angle-modulated two-dimensional single-cell pulsed-field gel electrophoresis (2D-SCPFGE) to observe DNA fragmentation in separated motile sperm. (2) Methods: We set up comparative standards, calibration curves, the required sensitivity, and eligibility criteria for test sperm to validate their measurement principles. (3) Results: We revealed that the conventional methods overlooked the interference of nucleoproteins in their measurements. In-gel proteolysis improves the measurement accuracies of 1D- and 2D-SCPFGE. We recommend using naked DNA for comparative standards and test specimens. Moreover, we have observed several dysfunctions that may induce DNA damage in the separated motile sperm. Overall, our discussion highlights the need to revisit the conventional univariable analyses based on the SCSA, SCD test, and CA. (4) Conclusions: Human infertility is a complex syndrome, and the aim of quality control in intracytoplasmic sperm injection is to identify the underlying dysfunctions remaining in the separated motile sperm that render them ineligible for injection. Well-designed, multivariable analyses with special consideration to confounding factors are necessary in future cohort studies.

The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Genome-wide association studies (GWAS) have successfully revealed many disease-associated genetic variants. For a case-control study, the adequate power of an association test can be achieved with a large sample size, although genotyping large samples is expensive. A cost‐effective strategy to boost power is to integrate external control samples with publicly available genotyped data. However, the naïve integration of external controls may inflate the type I error rates if ignoring the systematic differences (batch effect) between studies, such as the differences in sequencing platforms, genotype calling procedures, population stratification, and so forth. To account for the batch effect, we propose an approach by integrating External Controls into the Association Test by Regression Calibration (iECAT-RC) in case-control association studies. Extensive simulation studies show that iECAT-RC not only can control type I error rates but also can boost statistical power in all models. We also apply iECAT-RC to the UK Biobank data for M72 Fibroblastic disorders by considering genotype calling as the batch effect. Four SNPs associated with Fibroblastic disorders have been detected by iECAT-RC and the other two comparison methods. However, our method has a higher probability of identifying these significant SNPs in the scenario of an unbalanced case-control association study.

In this paper, we propose two novel methods for robot-world/hand-eye calibration and provide a comparative analysis against six state-of-the-art methods. We examine the calibration problem from two alternative geometrical interpretations, called hand-eye and robot-world-hand-eye, respectively. The study analyses the effects of specifying the objective function as pose error or reprojection error minimization problem. We provide three real and three simulated datasets with rendered images as part of the study. In addition, we propose a robotic arm error modeling approach to be used along with the simulated datasets for generating a realistic response. The tests on simulated data are performed in both ideal cases and with pseudo-realistic robotic arm pose and visual noise. Our methods show significant improvement and robustness on many metrics in various scenarios compared to state-of-the-art methods.

The tradeoff between the design phase and the experimental setup is crucial to satisfy the accuracy requirement of Large Deployable Reflectors. Manufacturing errors and tolerances change the RMS of the reflecting surface and require careful calibration of the tie rod system to be able to fit into the initial design specifications. To give a possible solution to this problem, here two calibration methods, respectively for rigid and flexible ring truss support, are described. Starting from the acquired experimental data on the net nodal coordinates, the initial problem of satisfying the static equilibrium at the measured configuration is described. Then, two constrained optimization problems, for rigid and flexible ring truss support, are defined to meet RMS accuracy of the reflecting surface modifying the tie lengths. Finally, a case study to demonstrate the validity of the proposed methods is presented.

In recent years, using multispectral cameras on UAVs has provided an opportunity to capture separate bands that offer the extraction of spectral features used for early detection of diseased plants. One of the main steps in disease detection is radiometric calibration that converts digital numbers to reflectance values commonly using white reference panels. This paper focused on the necessity of radiometric calibration to distinguish disease trees in orchards based on aerial multi-spectral images. For this purpose, two study sites with various climate conditions and tree species as well as different disease types were selected where multispectral images were taken using a multirotor UAV. The impact of radiometric correction on plant disease detection was assessed in two ways: 1) comparison of separability between the healthy and diseased classes using T-test and entropy distances; 2) radiometric calibration effect on the accuracy of classification. The experimental result showed the insignificant effect of radiometric calibration on separability criteria. Furthermore, based on T-test and entropy distances criteria, NIR and R spectral features made highest distances between healthy and Greening infected citrus trees, respectively, at the first study site while NDRE and BNDVI spectral features made highest distances between healthy and peach leaf curl infected trees, respectively, at the other study site. In the second strategy, the experimental result showed that radiometric calibration had no effect on the accuracy of classification. As a result, the overall accuracy and kappa values for both un-calibrated and calibrated orthomosaic classifications of the citrus orchard were 96.6% and 0.94%, respectively, using five spectral bands as well as DVI, NDRE, NDVI and GNDVI vegetation indices using a random forest classifier. The experimental results were also similar at the other study site. Therefore, the overall accuracy and kappa values for both the un-calibrated and calibrated orthomosaic classifications were 96.1%, 0.92, respectively, using five spectral bands as well as NDRE, BNDVI, GNDVI, DVI, and NDVI vegetation indices.

The co-circulation of duck hepatitis A virus subtypes 1 (DHAV-1) and 3 (DHAV-3) in ducklings has resulted in significant economic losses. Because ducklings infected with DHAV-1 or DHAV-3 show similar clinical signs and gross lesions, it is important to discriminate these subtypes as early as possible for better clinical management. On the basis of multiple alignments of the 5′-noncoding region sequences of strains DHAV-1 and DHAV-3, universal and type-specific primers were designed and synthesized. Using the primers in a one-tube reverse transcription-PCR (RT-PCR) assay, reference strains of DHAV-1 and DHAV-3 (isolated over a span of 60 years and covering many different countries) were successfully amplified, indicating that the primer sequences were completely conserved. The amplicon sequences results and the sizes of amplicons from reference DHAV-1 and DHAV-3 isolates correlated completely with their genotypes. Moreover, with this one-tube RT-PCR system, the amplicon sizes of liver samples of reference DHAV-1- or DHAV-3-infected birds matched perfectly with their respective genotypes, as determined by virus isolation and neutralization tests. No other RNA viruses of duck origin were detected with the synthesized primers. The sensitivity of viral RNA detection was 10 pg. With this system, 20% genotype 1, 45% genotype 3, and 9% co-infection of the two genotypes were detected in 55 clinical samples. This novel approach could be used for the rapid genotyping DHAV-1 and/or DHAV-3 infection in routine clinical surveillance or epidemiologic screening.

Hollow and concrete-filled steel tubes (CFSTs) are widely used as columns in many structural systems and local buckling can occur when they are subjected to axial compression loading. The critical regions for the local buckling of the columns are near the ends of the column where the moments are the highest. To strengthen the critical regions of the CFSTs the CFRP provides a simple and effective method which used previously as an enhancement for both of strength and ductility. So, this study suggests investigating the axial load behaviour of CFST strengthened with CFRP using FE method after a verification study and then a various parametric studies were carried out to cover the effect of the CFRP layers, number, confinement length and position. The FE results proved that, one CFRP sheet with thickness equal to 1.2 mm was strengthened the composite column by 8.5%, two CFRP sheets with total thickness equal to 2.4 mm was strengthened the composite column by 23.5%, three CFRP sheets with total thickness equal to 3.6 mm was strengthened the composite column by 35.1% and four CFRP sheets with total thickness equal to 4.8 mm was strengthened the composite column by 44.5%. Moreover, this study proved that by strengthened the composite columns with CFRP sheets with different lengths, the axial load resistance was improved by 8.5%, 4.6%, 0.1% and 0.0% for length percentages 100%, 75%, 50% and 25% respectively.

With metal oxide semiconductors being a promising candidate for accurate indoor air quality assessments, multiple drawbacks of the gas sensors prevent their widespread use. Examples include poor selectivity, instability over time, and sensor poisoning. Complex calibration methods and advanced operation modes can solve some of those drawbacks. However, this leads to long calibration times, which are unsuitable for mass production. In recent years, multiple attempts to solve calibration transfer have been made with the help of direct standardization, orthogonal signal correction, and many more methods. Besides those, a new promising approach is transfer learning from deep learning. This article will compare different calibration transfer methods, including direct standardization, piecewise direct standardization, transfer learning for deep learning models, and global model building. The machine learning methods to calibrate the initial models for calibration transfer are feature extraction, selection, and regression (established methods) and a custom convolutional neural network TCOCNN. It is shown that transfer learning can outperform the other calibration transfer methods regarding the root mean squared error, especially if the initial model is built with multiple sensors. It was possible to reduce the number of calibration samples by up to 99.3 % (from 10 days to approximately 2 hours) and still achieve an RMSE for acetone of around 18 ppb (15 ppb with extended individual calibration) if six different sensors were used for building the initial model. Furthermore, it was shown that the other calibration transfer methods (direct standardization and piecewise direct standardization) also work reasonably well for both machine learning approaches, primarily when multiple sensors are used for the initial model.

The study of fractures in the subsurface is very important in unconventional reservoirs since they are the main conduits for hydrocarbon flow. For this reason, a variety of equivalent medium theories have been proposed for the estimation of fracture and fluid properties within reservoir rocks. We experimentally investigated the feasibility of applying the Galvin model in fractured tight stones. For this proposal, three artificial fractured tight sandstone samples with the same background porosity (11.7% ± 1.2%) but different fracture densities of 0.00, 0.0312, and 0.0624 were manufactured. The fracture thickness was 0.06 mm and the fracture diameter was 3 mm in all the fractured samples. Ultrasonic P- and S-wave velocities were measured at 0.5 MHz in a laboratory setting in dry and water-saturated conditions in directions at 0°, 45°, and 90° to the fracture normal. The results were compared with theoretical predictions of the Galvin model. The comparison showed that model predictions significantly underestimated P- and S- wave velocities as well as P-wave anisotropy in water-saturated conditions, but overestimated P-wave anisotropy in dry conditions. By analyzing the differences between the measured results and theoretical predictions, we modified the Galvin model by adding the squirt flow mechanism to it and used the Thomsen model to obtain the elastic moduli in high- and low-frequency limits. The modified model predictions showed good fits with the measured results.

In the context of cognitive radio, smart city and Internet-of-Things, the need of advanced radio spectrum monitoring becomes crucial. However, surveillance of a wide frequency band without using extremely expensive high sampling rates devices is a challenging task. The recent development of compressed sampling approaches offers a promising solution to these problems. In this context, the Modulated Wideband Converter (MWC), a blind sub-Nyquist sampling system, is probably the most realistic approach and was successfully validated in real-world conditions. The MWC can be realized with existing analog components and there exist calibration methods which are able to integrate the imperfections of the mixers, filters and ADCs, hence allowing its use in real-world. The MWC underlying model is based on signal processing concepts such as filtering, modulation, Fourier series decomposition, oversampling and undersampling, spectrum aliasing, and so on, as well as in-flow data processing. In this paper we develop an MWC model which is entirely based on linear algebra, matrix theory and block processing. We show that this approach has many interests: straightforward translation of mathematical equations into simple and efficient software programming, suppression of some constraints of the initial model, and providing a basis for the development of an extremely fast system calibration method. With a typical MWC acquisition device we obtained a speed up of a factor greater than 20 of the calibration computation time, compared with a previous implementation.

Background: Accidental caustic burns of the esophagus in children represent a significant global health challenge, often necessitating esophageal reconstruction. The aim of this study is to compare the efficacy and morbidity related to esophagus replacement with colonic and gastric tube transplants in a pediatric population followed for caustic stenosis. Method: This retrospective study was conducted at a tertiary pediatric surgery unit for children treated from January 1989 to December 2022. We compared colonic and gastric tube esophageal replacement. Short-term (within 30 days) and mid-term outcomes and complications were reviewed. Statistical evaluation was considered using a Chi-square test for categorical data analysis. Results: A total of 124 children with caustic esophageal burns were included. Among them, 23 (18.5%) had a gastric tube transplant for esophagus replacement and 101 (81.5%) a colonic transplant. During surgical intervention, we found a significantly higher risk of complications when using a colonic transplant (34%, p < 0.001). There was no significant statistical difference in postoperative short-term and mid-term complications between the two techniques. Twenty-six (26%) of the children required a reoperation, with a higher risk in the gastric tube transplant group (p < 0.001). Endoscopic dilatation after surgery was also performed on a higher number of children who had received a gastric tube transplant (p = 0.005). Overall, 97.6% recovered full normal oral feeding. Conclusions: We found that colonic and gastric tube replacement are both good options for pediatric esophageal replacement after a caustic injury and show effectiveness over time. Gastric tube transplants carried a slightly higher risk of reoperations and a higher number of dilatations post-surgery. However, our groups are not really comparable due to the much higher number of colonic transplants. Both surgical options have to be considered during surgery and the choice depends on the anatomy of the patient. Our future research will focus on assessing long-term quality of life and potential risk of neoplastic complications.

The thoracic surgery has increased drastically in recent years, especially in the light of the severe outbreak of 2019 novel coronavirus disease (COVID-19). Routine “passive” chest computed tomography (CT) screening of inpatients detects some pulmonary diseases requiring thoracic surgeries timely. As an essential device for thoracic anesthesia, the double-lumen tube (DLT) is particularly important for anesthesia and surgery. With the continuous upgrading of the DLTs and the widespread use of the fiberoptic bronchoscopy (FOB), the position of DLT in thoracic surgery is gradually becoming more stable and easier to observe or adjust. However, the DLT malposition still occurs during transferring patients from supine to lateral position in thoracic surgery, which leads to lung isolation failure and hypoxemia during one-lung ventilation (OLV). Recently some innovative DLTs or improved intervention methods have shown good results in reducing the incidence of DLT malposition. This review aims to summarize the recent studies of the incidence of left-sided DLT malposition, the reasons and effects of malposition, and summarize current methods for reducing DLT malposition and prospects for possible approaches. Meanwhile, we use bibliometric analysis to summarize the research trends and hot spots of the DLT research.

Additive manufacturing (AM) is a promising new technology that is having a very fast growth from home workshops to high-tech cutting-edge factories. As any manufacturing technique, adequate metrology services are needed to assure the quality of items manufactured by AM. One of the most widely used instruments to measure the characteristics of surfaces manufactured with AM is the confocal microscope. In this paper, authors present a whole calibration procedure for confocal microscopes designed to be implemented preferably in workshops or industrial environments rather than in research and development departments. Because of that, it is as simple as possible. The procedure is designed without forgetting any of the key aspects that need to be taken into account and based on classical reference material standards. These standards can be easily found in industrial dimensional laboratories and easily calibrated in accredited calibration laboratories.

The development and generalization of Digital Volume Correlation (DVC) on X-ray computed tomography data highlight the issue of long term storage. The present paper proposes a new model-free method for pruning the DVC data. The size of the remaining sampled data can be user-defined, depending on the needs concerning storage space. The data pruning procedure is deeply linked to hyper-reduction techniques. The DVC data of a resin-bonded sand tested in uniaxial compression is used as an illustrating example. The relevance of the pruned data is tested afterwards for model calibration. A new Finite Element Model Updating (FEMU) technique coupled with an hybrid hyper-reduction method is used to successfully calibrate a constitutive model of the resin bonded sand with the pruned data only.

Most of the existing calibration methods for binocular stereo vision sensor (BSVS) depend on high-accuracy target with feature points that are difficult to manufacture and costly. In complex light conditions, optical filters are used for BSVS, but they affect imaging quality. Hence, the use of a high-accuracy target with certain-sized feature points for calibration is not feasible under such complex conditions. To solve these problems, a calibration method based on unknown-sized elliptical stripe images is proposed. With known intrinsic parameters, the proposed method adopts the elliptical stripes located on the parallel planes as a medium to calibrate BSVS online. In comparison with the common calibration methods, the proposed method avoids utilizing high-accuracy target with certain-sized feature points. Therefore, the proposed method is not only easy to implement but is a realistic method for the calibration of BSVS with optical filter. Changing the size of elliptical curves projected on the target solves the difficulty of applying the proposed method in different fields of view and distances. Simulative and physical experiments are conducted to validate the efficiency of the proposed method. When the field of view is approximately 400 mm × 300 mm, the proposed method can reach a calibration accuracy of 0.03 mm, which is comparable with that of Zhang’s method.

Primary spontaneous pneumothorax (PSP) is a pleural disease that abruptly affects healthy adolescents and young adults, representing a common thoracic disorder in this age group. This study aimed to investigate the necessity of preoperative chest tube insertion in patients with PSP and to re-evaluate current clinical treatment approaches. A retrospective review of medical records was conducted for children and young adults aged 14–30 years, diagnosed with PSP and who underwent Video-assisted thoracoscopic surgery (VATS) between January 2016 and December 2022 at Wonju Severance Christian Hospital. Patients were retrospectively divided into two groups based on their initial treatment: chest tube insertion and non-chest tube insertion. Clinical data including demographics, treatment details, and outcomes were collected and compared. Total 128 cases of PSP were included in the study. The total length of hospital stay was significantly shorter in the non-chest tube group (p=0.000), which was attributed to the omission of pre-operative chest tube insertions. No significant differences were observed between the two groups in terms of postoperative complications or recurrence rates. In cases of young patients with PSP, omitting pre-operative chest tube insertion may be a viable option if the patient is scheduled for VATS.

In a power plant that uses seawater as a coolant, a debris filter is required to remove foreign substances from the seawater, and differential pressure leads to a decrease in the coolant flow rate, leading to a decrease in power generation efficiency. In this study, analysis was performed under different initial flow velocity conditions of 1.5m/s, 2.0m/s, and 2.5m/s for a debris filter used in a power plant to understand flow characteristics in CTCS. The flow and differential pressure characteristics of a CTCS with an installed debris filter were considered in a comparative analysis of velocity, pressure, and turbulent kinetic energy distribution. The results confirmed that a vortex was generated in the pipe with the debris filter, apparently due to the collision of the flow with the bracket of the debris filter. As the flow rate increased, the range of the vortex increased, causing a loss in flow.

The pulsating flow is one of the techniques which can enhance heat transfer, therefore leading to energy saving in tubular heat exchangers. This paper investigates the heat transfer and flow characteristics in a two-dimensional in-line tube bundle with the pulsating flow by a numerical method using the Ansys Fluent. Numerical simulation is performed for Reynolds number Re = 500 with different frequencies and amplitude of pulsation. Heat transfer enhancement was estimated from the central tube of the tube bundle. Pulsation velocity had an asymmetrical character with a reciprocating flow. The technique developed by the authors to obtain asymmetric pulsations was used. This technique allows simulating an asymmetric flow in heat exchangers equipped with a pulsation generation system. Increase in both the amplitude and the frequency of the pulsations has a significant effect on heat transfer enhancement. Heat transfer enhancement is mainly observed in the front and back of the cylinder. At a steady flow in these areas, heat transfer is minimal due to the weak circulation of the flow. The increase in heat transfer in the front and back of the cylinder is associated with increased velocity and additional flow mixing in these areas.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

: AliCPT-1 is the first Cosmic Microwave Background (CMB) experiment in China, dedicated to achieve accurate measurements of B-mode polarization. Situated in Ali of Tibet, China, this telescope is currently undergoing deployment and will operate in two frequency bands centered at 90 and 150 GHz. The Far-Field Flat Mirror（FFF）is a calibration device of AliCPT-1 telescope for far-field beam mapping. The design of FFF is optimized for easy assembly and adjustment. Meteorological station data reveals that the maximum wind speed near FFF is 17.5 m/s, while the maximum wind speed on the windward side is 8 m/s. The wind pressure on FFF was analysed using a maximum wind speed of 17.5m/s as the input condition, based on the fluid-structure coupling method in ANSYS. The results demonstrate that it is safe and reliable when withstanding combined gravity and wind pressure loads. The torque on the mount is within the motor rated torque. The flatness of the FFF reflective surface can be adjusted to an RMS value of 0.05 mm when taken into account the effect of gravity and assembly accuracy. The deformation caused by the maximum wind loads is approximately 0.0587 mm under the protection of wind-proof wall. The combined deformation is 0.077 mm in RMS value combining the two influences, which is less than 1/20 of wavelength. The FFF mirror assembly is stable and precisely for telescope calibration.

The surface electromyogram (sEMG)--based gesture recognition to the development of intelligent prostheses has emerged as a promising avenue for upper limb amputees. However, the temporal variations in sEMG have rendered recognition models less efficient than anticipated. Cross-session calibration and training data indicate the capacity to reduce this variation. The impact of varying calibration and training data amounts on gesture recognition performance for amputees is still unknown. To assess these effects, we present four datasets for the evaluation of calibration data and examine the impact of training data volume on benchmark performance. Two amputees who had undergone amputations years prior were recruited and seven sessions of data were collected for analysis from each of them. The experimental results show that the calibration data improved the average accuracy per subject by 3.03% and 6.16%, respectively, compared to the baseline results. Moreover, it was found that to collect training data for modeling, boosting the number of training sessions proves more efficient than increasing the number of trials within a single session. Two potentially effective strategies are proposed in light of this research to enhance the cross-session models further. We consider these findings to be of the utmost importance for the commercialization of intelligent prostheses, as they demonstrate the criticality of gathering calibration and cross-session training data, as well as offer effective strategies for maximizing the utilization of the entire dataset.

Tipping bucket rain gauges (TBRs) have been, and apparently will continue to be one of the most widely used pieces of equipment for rainfall monitoring, being frequently used for the calibration, validation and downscaling of radar and remote sensing data, due to their major advantages–low cost, simplicity, and low energy consumption. Thus, many works have focused and continue to focus on their main disadvantage–measurement biases (mainly in wind and mechanical underestimations). However, despite arduous scientific effort, calibration methodologies are not frequently implemented by monitoring networks operators or data users, propagating bias in databases and in the different applications of such data, causing uncertainty in the modeling, management, and forecasting in hydrological research, mainly due to a lack of knowledge. Within this context, this work presents a review of the scientific advances in TBR measurement uncertainties, calibration, and error reduction strategies from a hydrological point of view, by describing different rainfall monitoring techniques in Section 2, summarizing TBR measurement uncertainties in Section 3, focusing on calibration, and error reduction strategies in Section 4, a discussion and perspectives in Section 5, and conclusions in Section 6, providing an overview of the of the state of the art and future perspectives of the technology.

The inverse finite element method (iFEM) is a novel method for reconstructing the full-field displacement of structures by discrete measurement strain. In practical engineering applications, the accuracy of iFEM is reduced due to the positional offset of strain sensors during installation, and errors in structural installation. Therefore, coarse and fine two-stage calibration (CFTSC) method is proposed to enhance the accuracy of the reconstruction of structures. Firstly, the coarse calibration is based on a single-objective particle swarm optimization algorithm to optimize the displacement-strain transformation matrix related to the sensor position. Secondly, as selecting different training data can affect the training effect of self-constructed fuzzy networks, this paper proposes to screen the appropriate training data based on residual analysis. Finally, the experiments of the wing integrated antenna structure verify the efficient of the method on the reconstruction accuracy of the structural body displacement field.

FY-3E WindRAD (Fengyun-3E Wind Radar) is a dual-frequency rotating fan-beam scatterometer. Its data characteristics, NOC (NWP Ocean Calibration), and wind retrieval performance are investigated in this paper. The radar view geometry diversity varies across the swath, with maximum diversity in the sweet swaths and limited diversity in the outer and nadir swaths. When NOC backscatter calibration coefficients are computed as a function of incidence angle only (NOCint), a smooth correction is found. However, when relative antenna azimuth angle is included (NOCant), it appears that the corrections as a function of relative azimuth angle vary harmonically and substantially for a specific incidence angle. NOCant corrections yield a better fit of the measurements to the GMF (Geophysical Model Function). Hence NOCant is applied for the wind retrieval analysis from Ku-band, C-band. An extra engineering correction of 0.15dB and 0.2dB is applied on Ku-band and C-band backscatter values, respectively, to reduce the wind speed bias without increasing the standard deviation. Overall, NOCant is the best option for both channels. Also, the instrument backscatter data stability over time is good and the retrieved winds can fulfill operational requirements.

Eustachian Tube Dysfunction is considered a common condition among ENT patients and requires careful history, clinical examination and appropriate investigations to obtain a diagnosis. The ETDQ-7 questionnaire is a useful tool to subjectively score severity of symptoms that are related to this pathology (Appendix A). This study aimed to adapt and validate the ETDQ-7 questionnaire in Greece to ensure correct and efficient use in the outpatient setting (Appendix B). The ETDQ-7 was translated into the Greek language following appropriate methodology. Data for the main study were collected from a sample of 75 Greek patients diagnosed with ETD as well as 25 patients that did not have ETD and who served as a control group. The participants completed the adapted ETDQ-7 questionnaire and underwent a clinical examination that was statistically correlated with their ETDQ-7 answers. Face and content validity were confirmed and the questionnaire was found easy to administer and to be completed by our patients. Test-retest reliability revealed similar internal consistency for the questions and good correlation between individual items and total score. Discriminative validity confirmed statistically significant difference between the two patient groups to ensure that the Greek version of ETDQ-7 is useful to confirm the diagnosis. The Greek version of the ETDQ-7 is safe and efficient to use among a variety of investigation methods for the diagnosis of ETD in the Greek speaking population.

Accurately monitoring insecticide resistance in target mosquito populations is important to combating malaria and other vector-borne diseases, and robust methods are key. The “WHO susceptibility bioassay” has been used for +60 years: mosquitoes of known physiological status are exposed to a discriminating concentration of insecticide. Several changes to the test procedures have been made historically which may seem minor but could impact bioassay results. The published test procedures and literature for this method were reviewed for methodological details. Areas where there was room for interpretation in the test procedures or where the test procedures were not being followed were assessed experimentally for impact on bioassay results: covering or uncovering of the tube end during exposure, number of mosquitoes per test unit, and mosquito age. Many publications do not cite the most recent test procedures, methodological details are reported which contradict the test procedures referenced or methodological details are not fully reported. As a result, the precise methodology is unclear. Experimental testing showed that using fewer than the recommended 15-30 mosquitoes per test unit significantly reduced mortality, covering the exposure tube had no effect, and using mosquitoes older than 2-5 days old increased mortality, particularly in the resistant strain. Recommendations are made for better reporting of experimental parameters.

Beginning with the discovery of the BRCA ovarian cancer susceptibility genes and subsequent detailed examination of risk reduction salpingo-oophorectomy (RRSO) specimens, a new paradigm of ovarian carcinogenesis has unfolded with attention to the distal fallopian tube. The primary focus has been an early cancer in the fallopian tube which is seen in virtually all incidentally discovered high-grade serous cancers in asymptomatic women. This high-frequency of tubal involvement in early serous cancer - serous tubal intraepithelial carcinoma or STIC - has galvanized attention to this organ as a primary source of this disease. However, an enduring mystery has been the relatively low frequency of STIC in fallopian tubes of women with advanced malignancy. This paradox, a high-frequency of tubal involvement early and a low-frequency late in the disease process has spurred interest in other potential sources, such as the ovarian surface or secondary Mullerian system. However, because essentially all high-grade serous carcinomas are linked by TP53 mutations, and because fallopian tubes frequently contain early serous proliferations (ESPs) with these mutations, attention has turned to the possibility that nonmalignant but TP53 mutated tubal epithelium could be responsible for an eventual malignancy. Recent data have shown evidence of lineage continuity between ESPs and concurrent serous carcinomas prompting the concept of "precursor escape". This creates a 2nd component of the paradigm by which cells from early lesions can escape the fallopian tube and undergo future malignant transformation later, emerging suddenly as widespread malignancy. This dualistic model thus explains the paradox and opens new questions pertaining to the challenge of both early detection and prevention of this lethal malignancy.

High-grade advanced ovarian, fallopian tube and primary peritoneal (HGAOC) cancer are malignancies in which, apart from surgical treatment, systemic treatment plays an important role. The improvement in treatment results is associated with the introduction of polyADP-ribose polymerase inhibitors (PARPis). The aim of this study is to present a cross-section of patients treated for HGAOC, in one center, including the distribution of treatment principles following the most up-to-date guidelines. We observed patients who reported to the Department of Gyneacological Oncology between January 2018 and December 2023. We analyzed 437 women with a first diagnosis of HGAOC, who had not been treated before. The introduction of combined treatment with bevacizumab and PARPi into the first line of treatment, regardless of any remnants left during cytoreductive surgery, was introduced in November 2022. Since then, 30% (18/60) of patients (14 with olaparib and 4 with niraparib) have used the above regimen. Previously, in May 2021 - October 2022, it was 27% of patients (13/81 with olaparib and 9/81 with niraparib). Among patients starting treatment in January 2018 - April 2021, only 4.7% (5/106) received the platinum + paclitaxel + olaparib regimen. In both groups – with and without BRCA1/2 pathogenic or likely- pathogenic variant, significantly more patients used PC + PARPi or PC + BEV + PARPi in periods II and III than in period I (p<0.01). The introduction of modern treatment in our center very quickly changed the structure of patient treatment. Carriers of BRCA1/2 pathogenic or likely-pathogenic variant had previously received only chemotherapy, disappeared after the introduction of PARPi, in favor of new therapies. Most patients with no BRCA1/2 pathogenic or likely-pathogenic variant, who used PARPi in therapy in our center – received niraparib and therefore they are beneficiaries of molecular diagnostics in the field of HRD.

Cell-free DNA (cfDNA) analysis is a pivotal tool in non-invasive diagnostics, including cancer monitoring and prenatal testing. However, the preanalytical phase, particularly the choice of anticoagulant, significantly impacts cfDNA integrity and yield. This study aims to compare cfDNA yield, stability, and DNase activity across plasma-citrate, plasma-heparin, plasma-EDTA, and serum, to identify the most suitable specimen for cfDNA analysis among the tested anticoagulants. Blood samples from 15 healthy volunteers were collected in four types of tubes (citrate, heparin, EDTA, and serum). cfDNA was extracted and quantified using qPCR, and endogenous DNase activity was assessed through hydrolysis probe assays. Samples were incubated at 37°C for 24 hours to evaluate cfDNA degradation rates. Statistical analyses were performed using repeated measures ANOVA and Sidak's multiple comparison tests. Baseline cfDNA levels were highest in serum, followed by heparin-plasma, while EDTA and citrate-plasma exhibited the lowest levels. DNase activity was fully inhibited in EDTA-plasma, partially inhibited in citrate-plasma, and active in both heparin-plasma and serum. cfDNA degradation was most pronounced in heparin-plasma (85.3%) and serum (55.6%), compared to minimal degradation in EDTA (8%) and citrate-plasma (13.3%). Among the tested anticoagulants, EDTA-plasma proved to be the most suitable specimen for cfDNA analysis due to its low DNase activity and minimal gDNA contamination. Citrate-plasma, with intermediate DNase inhibition, could be an alternative if the citrate concentration were increased. Heparin-plasma and serum showed significant cfDNA degradation, rendering them unsuitable for cfDNA analysis. These findings highlight the importance of anticoagulant selection in preserving cfDNA integrity for diagnostic applications.

Studies have shown that vehicle trajectory data are effective for calibrating microsimulation mod-els. Light Detection and Ranging (LiDAR) technology offers high-resolution 3-D data, allowing for detailed mapping of the surrounding environment, including road geometry, roadside infrastruc-tures, and moving objects such as vehicles, cyclists, and pedestrians. This research presents a comprehensive framework for integrating LiDAR sensor data into simulation models and accu-rately calibrating for proactive safety analysis. Vehicle trajectory data were extracted from LiDAR point cloud collected at six urban signalized intersections in Lubbock, Texas in USA. Each study intersection was modelled with PTV VISSIM and calibrated to replicate the observed field scenarios. The Directed Brute Force method was used to calibrate two car-following and two lane-change parameters of Wiedemann 1999 model in VISSIM, resulting in an average accuracy of 92.7%. Rear-end conflicts extracted from the calibrated models combined with a ten-year historical crash dataset were fitted into a Negative Binomial (NB) model to estimate the model's parameters. In all the six intersections, rear-end conflict count is a statistically significant predictor (p-value < 0.05) of observed rear-end crash frequency. The outcome of this study provides a framework for the com-bined use of LiDAR-based vehicle trajectory data, microsimulation and surrogate safety assessment tools to transportation professionals for proactive safety evaluation.