K-band radar waves have high penetration and low attenuation coefficients. However, the wavelength of this radar wave is relatively short; thus, designing and preparing both broadband and wide-angle radar wave absorbers in this band presents considerable challenges. In this study, a resin-based K-band radar wave absorber with a biomimetic lotus leaf structure was designed and formed by UV curing. Here, microscale lotus leaf papillae and antireflection structures were prepared using a DLP 3D printer, and the contact angle between the material and water droplets was increased from 56° to 130°. In addition, the influence of the geometric parameters of the lotus leaf antireflection structure on the electromagnetic absorption performance and mechanical strength was investigated. After simulation optimization, the maximum electromagnetic loss of the lotus leaf structure 3D printed sample was −32.3 dB, and the electromagnetic loss was below −10 dB in the 20.8–26.5 GHz frequency range. When the radar incidence angle was 60°, the maximum electromagnetic loss was still less than −10 dB. The designed lotus leaf structure has a higher mechanical energy absorption per unit volume (337.22 KJ/m3) and per unit mass (0.55 KJ/Kg) than commonly used honeycomb lightweight structures during the elastic deformation stage, and we expect that the designed structure can be used as an effective lightweight material for K-band radar stealth.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

In a saline semi-isolated Lagoon on the Cape Zeleny (White Sea), the annual dynamics of the vertical hydrological structure, and the seasonal dynamics of phytoplankton were traced, including species composition, and vertical distribution, abundance, nutrition type,and biomass.293 species and supraspecific taxa of algae and cyanobacteria were found. Most of the identified species are marine, and 38 species are freshwater. Taxonomic composition changed in the Lagoon during the year. Dinoflagellates dominated in winter and early June; unidentified cocci and flagellates in July; diatoms, dinoflagellates and unidentified cells in August; dinoflagellates in September; and unidentified cocci and flagellates in October–November. The abundance of algae also changed in the Lagoon during the year. The integrated biomass in the water column varied from 0.01 g C/m2 in January to 0.78 g C/m2 in early September. According to the abiotic parameters, the water column of the Lagoon is subdivided into several zones with different conditions and corresponding phytoplankton communities. Similarity between the communities of different horizons was 32-46% in summer and 7% in winter. The chemocline layer was the most populous. Almost the entire year it contained a maximum of phytoplankton biomass, 1-2 orders of magnitude higher than that in the overlying horizons. Comparison phytoplankton in the lagoon and in the nearby sea area was carried out. Despite the connection between the Lagoon and the sea phytoplankton structure in the surface water layer in the Lagoon and in the sea differs significantly in composition, quantitative parameters, and seasonal dynamics. The similarity of the communities in the sea and the Lagoon never exceeded 50%. In terms of biomass, the Lagoon lags behind the sea until mid-summer, but, starting from August, it outnumbers it, and the phytoplankton development in the Lagoon lasts longer, until late autumn. The phytoplankton structure and dynamics in the Lagoon and the sea by 24.5% was related to the daylight, water salinity, oxygen content and pH, but did not depend on water T, underwater illuminance, and depth. Oxygen content and pH are defined by PhP activity. Salinity serves as a vector of the vertical sequence of ecological niches. The daylight length seems to be the crucial factor of the seasonal PhP dynamics in the semi-isolated coastal stratified lakes and lagoons.

Recent studies investigated the detectability of ship wake signatures on SAR imagery using a large number of SAR images collocated with Automatic Identification System data for training machine learning models. These detectability models are in agreement with oceanographic expectations from preceding studies and can therefore be used for comparing the performance of different SAR sensors in terms of wake detectability. Previous model comparisons showed better wake detection performance of TerraSAR-X (TS-X) than of RADARSAT-2 (RS2) and Sentinel-1 (S1). A comparison between CosmoSkymed (CSK) and RS2 is performed here, to examine the hypothesis that X-Band is generally better for wake detection than C-Band. Finally, this hypothesis is not confirmed, as the detectability models for TS-X, CSK and RS2 reveal similar performances. A comparison of wake detection performance should take the individual wake components into account separately.

Recent research has drawn attention to the ambiguity surrounding the definition and learnability of Out Of Distribution (OOD) recognition. The term "Out of Model Scope" (OMS) detection provides a clearer perspective, although the original problem remains unsolved. The ability to detect OMS inputs is particularly beneficial in safety-critical applications such as autonomous driving or medicine. By detecting OMS situations, we not only enhance the system's robustness but also prevent it from operating in unknown and unsafe scenarios. In this paper, we introduce a novel approach for OMS detection that combines three sources of information: 1) the original input, 2) the latent feature space extracted by an encoder, and 3) the synthetic data generated from the encoder's latent feature space. We demonstrate the effectiveness of combining original images and synthetically generated images against adversary attacks in the computer vision domain. We achieve results comparable to other state-of-the-art methods and demonstrate that any Encoder can be integrated into our pipeline in a plug-and-train fashion. Our experiments further evaluate which combination of the Encoder's features works best in order to discover OMS samples and highlight the importance of a compact feature space for the training of the Generator.

Retails and shopping centers have become essential to today’s lifestyle. Furthermore, as modern shopping venues, retail centers' social role contributes to its popularity and profitability. The social motive of customers for shopping is beyond acquiring their crucial purchases. These advantages favor retail centers and improve the level of social sustainability and its relevant concepts. Given that relatively little study has been studied on the impact of retail centers' social role as places for interactional and recreational activities on customers' behavior in these centers and its relation to social sustainability. Two hypotheses were raised that show the effect of time travel duration and shop variety on increasing the percentage of users who spend their leisure time and recreational activities in two analogous retail centers. The result of research regarding the first hypothesis reveals that there is an interaction between time travel duration and shoppers' motivation. Furthermore, the results revealed that half of both retail center goers who spend more than 10 minutes to arrive at the retail centers prefer to do leisure activities and browsing than shopping. Therefore, the majority of individuals are from further distances, indicating longer trips can be one of the factors for willing to spend more leisure time and recreational activities. The second hypothesis reveals that shop variety can be one of the main reasons for attracting users to spend their leisure time and browse in both retail centers. There is a significant correlation between shop variety and customers’ motivation.

People have always hoped to be able to fill an entire plane with ``single unit cells'' without periodicity. This wish was realized after the mathematician discovered a 13-sided ``single unit cell'' named `einstein'. These non-periodic tessellations generally exhibit anisotropic properties, making them superior in terms of mechanical performance compared to periodic structures. From the perspective of information entropy, the reason behind the improved mechanical properties of these structures is the higher entropy associated with non-periodic configurations. To quantify the disorder of non-periodic structures, we propose an entropy expression for the `einstein' metamaterial. To demonstrate the mechanical properties of these high-entropy structures, we fabricate specimens using 3D printing and conducte mechanical experiments. For comparative analysis, we also use ABAQUS to perform finite element analysis of the problem. The research results reveal that the mechanical properties of high-entropy structures created by the non-periodic stacking of cells are significantly improved compared to those of low-entropy structures created by periodic stacking. The conclusions drawn from the study of individual issues are generalizable and may be of assistance in future material and structural design.

The main purpose of this paper is to propose a novel optimization model with a new machine learning approach in the first section to achieve the best results in financial institutions in the second section. Since the constancy of efficacy derived from parametric and non-parametric is not significant, this paper provides a scientific assessment at the optimization section and proposes a novel combined parametric and non-parametric model which will be a new experiment in literature perception. A scientific assessment of banks based on a combination of the efficiency measurement method of CCR(Charnes, Cooper and Rhodes model) or CRS(Constant Return to Scale) BCC(Banker, Charnes, and Cooper model) or VRS (Variable Return to Scale) in Data Envelopment Analysis (DEA), as well as Stochastic Frontier Approach (SFA) for 65 banks during Feb to July 2020, are introduced. For analyzing the performance of the parametric and non-parametric approaches we have considered the linear regression and Unreplicated Linear Functional Relationship (ULFR). At the machine learning section, a novel four-layers data mining filtering pre-processes for selected supervised classification as well as unsupervised clustering algorithms to increase the accuracy and to remove unrelated attributes and data are applied. For the four kinds of preprocessing approaches of unsupervised attributes, supervised attributes, supervised instances, and unsupervised instances, we have chosen discretization, attribute selection, stratified remove folds, and resample filters respectively. Based on the nature of the suggested financial institution's dataset and attributes, the most appropriate preprocessing filter in each layer to achieve the highest performance is suggested. Finally, the superior bank, best performance model, and the most accurate algorithm are introduced. The results indicate that the bank number 56 is the superior bank. Among the proposed techniques, the novel recommended CVS compared with CCR-BCC and SFA models, has a more positive correlation with profit risk, and show a higher coefficient of determination values. Sequential Minimal Optimization(SMO) algorithm receives the highest accuracy in all four suggested filtering layers.

Reinforcement learning (RL) is an extensively applied control method for the purpose of designing intelligent control systems to achieve high accuracy as well as better performance. In the present article, the PID controller is considered as the main control strategy for brushless DC (BLDC) motor speed control. For better performance, the fuzzy Q-learning (FQL) method as a reinforcement learning approach is proposed to adjust the PID coefficients. A comparison with the adaptive PID (APID) controller is also performed for the superiority of the proposed method, and the findings demonstrate the reduction of the error of the proposed method and elimination of the overshoot for controlling the motor speed. MATLAB/SIMULINK has been used for modeling, simulation, and control design of the BLDC motor.

Since surface relief transmission gratings have very strict requirements on operators and use environment, according to the semiconductor laser external cavity spectral beam combining system, this paper proposes a design scheme of semiconductor laser array spectral beam combining system based on grating-external cavity. The finite element approach was used to create a wideband, high-efficiency fill-in multilayer dielectric transmission grating structure for a high-power spectrum beam combining system. The incidence angle, ridge height, duty cycle, and sidewall inclination angle of the transmission grating were tuned and evaluated, and a link between the transmission grating's diffraction efficiency and grating characteristics was discovered. The calculated design of the high-power fused silica transmission grating has a negative first-order peak diffraction efficiency of 99.5% in the 800nm range. In the spectral region of 765-872 nm, the transmission grating's diffraction effectiveness exceeds 92%. The filled ultra-high diffraction efficiency multilayer dielectric transmission grating design addresses the issue of resistance to high-power lasers under complicated operating settings, it’s intended to maintain a high diffraction efficiency even after several cleaning cycles, and it’s an ideal component for high-power spectrum beam combining systems.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

Triangular resonators re-shaped with the Sierpinski geometry and U-shaped resonators have been designed, linking them with single-pole-double-through (SPDT) RF MEMS switches to provide frequency tuning for potential applications in the K-Band. Prototypes of band-stop narrowband filters working around 20 GHz and 26 GHz, interesting for RADAR and satellite communications, have been studied in coplanar waveguide (CPW) configuration, and the tuning was obtained by switching between two paths of the devices loaded with different resonators. As a result, dual-band operation or fine-tuning can be obtained depending on the choice of the resonator, acting as a building block. The studied filters belong to the more general group of devices inspired by the metamaterial design.

Deep learning has increasingly been employed to identify minerals. However, deep learning can only be used to identify minerals in the distribution of the training set, while any mineral outside the spectrum of the training set is inevitably categorized erroneously within a predetermined class from the training set. To solve this problem, the study introduces the approach that amalgamates One-Class Support Vector Machines (OCSVM) with the ResNet architecture for the out-of-distribution mineral detection. Initially, ResNet undergoes training using a training set comprising well-defined minerals. Subsequently, the earlier layers of the trained ResNet are employed to extract the discriminative features of the mineral under consideration. These extracted mineral features then become the input for OCSVM. When OCSVM discerns the mineral in the training set's distribution, it triggers the subsequent layers within the trained ResNet, facilitating the accurate classification of the mineral into one of the predefined categories encompassing the known minerals. In the event OCSVM identifies the mineral out of the training set's distribution, it is unequivocally categorized as an unclassified or 'unknown' mineral. Empirical results substantiate the method's capability to identify out-of-distribution minerals while concurrently maintaining a commendably high accuracy rate for the classification of the 36 in-distribution minerals.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

Systemic inflammation and coronary microvascular endothelial dysfunction are essential pathophysiological factors in heart failure with preserved ejection fraction (HFpEF) that support the use of statins. The pleiotropic properties of statins, such as anti-inflammatory, antihypertrophic, antifibrotic, and antioxidant effects, are generally accepted and may be beneficial in HF, especially in HFpEF. Numerous observational clinical trials have consistently shown a beneficial prognostic effect of statins in patients with HFpEF, while the results of two larger trials in patients with HFrEF have been controversial. Such differences may be related to a more pronounced impact of the pleiotropic properties of statins on the pathophysiology of HFpEF and pro-inflammatory comorbidities (arterial hypertension, diabetes mellitus, obesity, chronic kidney disease) that are more common in HFpEF. This review discusses the potential mechanisms of statin action that may be beneficial for patients with HFpEF, as well as clinical trials that have evaluated the statin effects on left ventricular diastolic function and clinical outcomes in patients with HFpEF.

Emotion recognition defined as identifying human emotion and is directly related to different fields such as human-computer interfaces, human emotional processing, irrational analysis, medical diagnostics, data-driven animation, human-robot communi- cation and many more. The purpose of this study is to propose a new facial emotional recognition model using convolutional neural network. Our proposed model, “ConvNet”, detects seven specific emotions from image data including anger, disgust, fear, happiness, neutrality, sadness, and surprise. This research focuses on the model’s training accuracy in a short number of epoch which the authors can develop a real-time schema that can easily fit the model and sense emotions. Furthermore, this work focuses on the mental or emotional stuff of a man or woman using the behavioral aspects. To complete the training of the CNN network model, we use the FER2013 databases, and we test the system’s success by identifying facial expressions in the real-time. ConvNet consists of four layers of convolution together with two fully connected layers. The experimental results show that the ConvNet is able to achieve 96% training accuracy which is much better than current existing models. ConvNet also achieved validation accuracy of 65% to 70% (considering different datasets used for experiments), resulting in a higher classification accuracy compared to other existing models. We also made all the materials publicly accessible for the research community at: https://github.com/Tanoy004/Emotion-recognition-through-CNN.

Possibilities of utilization of two frequencies synthetic aperture radar (SAR) operating simultaneously in P-band and S or L-band are considered. Advantages of such system are shown. They are caused by improvement of data interpretation and by decrease of ionosphere influence. Tasks of surface and subsurface sensing by the complex SAR were under investigation for vegetation, soil covers are given. As an example, the investigation results of coniferous forest areas backscattering by the spaceborne P-band SAR together with L-band SAR in the September-February period are presented. Studies have shown that the joint use of the results in L and P bands offer unique opportunities to explore the effects of changes in the backscattering properties of forest surfaces.

The band gap research in graphene is still a very important topic for materials application. Here, we report a band gap opening and p-type semiconducting property of the graphene by using an electrochemical doping on graphene surface. The manganese-oxide nanopar-ticles adsorbed on the graphene were used as the dopants in an electrolyte, which induce the band gap opening and the change of electronic structure. In addition, the fabricated graphene FET shows the p-type semiconductor behaviors. The temperature dependent conductivity of the p-type doped graphene at applied potential of 1.5 V during electro-chemical doping shows the formation of band gap of 0.23 eV, which is obtained from the fitting of conductivity equation. The semiconducting properties of manganese-oxide doped graphene is attributed to the formation of manganese-oxide nanoparticle on the surface of graphene.

An accurate outbreak prediction of COVID-19 can successfully help to get insight into the spread and consequences of infectious diseases. Recently, machine learning (ML) based prediction models have been successfully employed for the prediction of the disease outbreak. The present study aimed to engage an artificial neural network-integrated by grey wolf optimizer for COVID-19 outbreak predictions by employing the Global dataset. Training and testing processes have been performed by time-series data related to January 22 to September 15, 2020 and validation has been performed by time-series data related to September 16 to October 15, 2020. Results have been evaluated by employing mean absolute percentage error (MAPE) and correlation coefficient (r) values. ANN-GWO provided a MAPE of 6.23, 13.15 and 11.4% for training, testing and validating phases, respectively. According to the results, the developed model could successfully cope with the prediction task.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

P-band radar remote sensing applied during the Airborne Microwave Observatory of Subcanopy and Subsurface (AirMOSS) mission has shown great potential for estimation of root zone soil moisture. When retrieving the soil moisture profile (SMP) from P-band radar, a mathematical function describing the vertical moisture distribution is required. Because only a limited number of observations are available, the number of free parameters of the mathematical model must not exceed the number of observed data. For example, a second order polynomial that contains 3 free parameters was presumed based on in-situ SMP data. The polynomial is currently parameterized based on 3 backscatter observations provided by AirMOSS (i.e. one frequency at three polarizations of HH, VV and HV). In this paper, a more realistic, physically-based SMP model containing 3 free parameters is derived based on a solution to Richards’ equation for unsaturated flow in soils. Evaluation of the new SMP model based on both numerical simulations and measured data revealed that it exhibits greater flexibility for fitting measured and simulated SMPs than the currently applied polynomial. It is also demonstrated that the new SMP model can be reduced to a second order polynomial at the expense of fitting accuracy.

Why do stretched rubber bands not hit the hand after ejection? What is the mechanism behind the rubber band ejection dynamics? These questions represent a fascinating scientific problem. Because the size of a rubber band in the circumferential direction is much larger than that in the other two directions of its cross-section, we regard the rubber band as a slender beam and establish a mathematical model of the dynamics of the rubber band stretching and ejection. Furthermore, we obtain the dependence of the dynamic curvature of the rubber band on the arc length and time. We used the finite element software ABAQUS to simulate the dynamic process of a rubber band stretching and ejection. The simulation results and dimensional analysis were performed to examine the effect of the bending elastic rebound velocity. The mathematical model and simulation results revealed that the relationship between the curvature and time at the end of the rubber band ($s =0$) was as follows: $\kappa\sim t^{-{1}/{2}}$. This research has guiding significance for the design of rubber bands as elastic energy storage devices.

This paper studies the duration patterns of unemployment spells for immigrants and the determinants of unemployment’s completion into one of a number of studied labour market states in Finland. We estimate a duration model for unemployment with competing risks of its terminating into employment, labour market training or economic inactivity. Taking into account the wide period of observation and opportunities to analyse processes of labour market integration during various periods of economic development in Finland, in combination with the individualistic character of the labour careers of immigrants, this research is beneficial owing to the many various findings concerning labour market integration of immigrants. The approach undertaken in this research has a dualistic “descriptive-dynamic” character under which integration is understood as a never-ending process, which is conditioned by a time period of long-term existence and a context of solitary action. We find that transitions out of unemployment spells have a cyclical character; after every new “cycle” in unemployment, the probability of terminating unemployment decreases further. We also find that ascriptive factors make sense in the process of job-placement of immigrants from unemployment. Therefore, the gender, education and age of immigrants, as well as the effect of the period in which first unemployment occurred, potentially predict transitions out of unemployment and further labour market integration of immigrants.

Abstract: Polylactic acid (PLA) is brittle in nature with extensive deformation property. For improvement of the end-use quality, it is of significant importance to enhance the producibility of fused deposition modeling (FDM)-printed objects in PLA. The purpose of this investigation is to boost toughness and to reduce the production cost of the FDM-printed tensile test samples with the desired part thickness. To attain the research purpose number of experiments are designed and analyzed by the Response Surface Method (RSM). The statistical analysis is performed to deal with this concern considering layer thickness, infill percentage, and extruder temperature as controlled factors. The tensile test specimens are printed based on the designed experiments, and the tensile strength tests are conducted by SANTAM 150 universal testing machine based on ASTM D638. The honeycomb internal fill pattern is applied for the production of light-weight and high-strength specimens. The area under Force- Extension curve up to fracture is acquired as the toughness of the printed specimens. This study also developed a modeling process using ANN and ANN-GA techniques for developing an accurate estimation for toughness, part thickness, and production cost as dependant variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid ML technique could successfully improve the accuracy of modeling about 7.5, 11.5 and 4.5 % for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. In the other side, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which develops the usability of printed PLA objects. The research is accomplished under the constraints of PLA compatibility with existing fused deposition modeling setup without changing the functional hardware/software of the machine. Although the mechanical properties and dimensional accuracy of PLA have already been studied, there is little literature on the toughness of the printed PLA with honeycomb internal fill pattern.

Steel fibre reinforced concrete (SFRC) consists of short hooked steel fibres randomly distributed and oriented within the cementitious matrix. The contribution of fibre in bridging cracks to provide the stress transfer required relies upon the orientation of the fibre in the concrete. Bridging fibre aligned with a crack are less effective than those inclined to it. Therefore, understanding the pull-out behaviour of misaligned fibre is a key factor to quantify and optimize the design of SFRC in the structural applications. In the laboratory a single oriented fibre embedded in a solid cylinder of concrete is subjected to a pull-out test where the axis of a tensile force is aligned with the axis of the cylinder. Based upon the observed behaviour this paper presents a new analytical bounding approach to capture the pull-out response of misaligned hooked-end steel fibre embedded in a concrete matrix. The analysis is based upon a transversely isotropic condition assumed for the plasticity that occurs in the cold drawn fibre. The model accounts for the influence of fibre diameter and the combined strengths of the steel and concrete. The model predictions have also been compared with other experimental results published in the literature. The results showed that the model can predict pull-out loads reasonably for different fibre orientations between bounds of failure derived from the strengths of the two constituents. A critical orientation is observed at maximum strength. Therein, an understanding of the pull-out behaviour of misaligned, hooked-end fibres is necessary to optimize the strength of concrete from this method of reinforcement.

In this letter, we propose a pattern-diversity antenna with different radiation patterns at two different frequency bands (f1 and f2) (f1: broadside radiation pattern, f2: conical radiation pattern). The proposed structure consists of a central circular antenna and two annular ring antennas; each of the three antennas has individual ports. Two of the ports exhibit orthogonal broadside radiation patterns; the other two ports exhibit orthogonal conical radiation patterns. Thus, they have polarization diversity characteristics. To improve isolation between ports, the inner part of the annular ring antennas is shorted via array, and the outermost port is positioned orthogonal to the other ports. Using this configuration, the isolation between ports was measured as -26.7 dB and -30.1 dB at the two frequency bands, respectively. Experimental results based on the fabricated prototype show that the proposed antenna achieves -10 dB bandwidths of 240 MHz (5.71~5.95 GHz) and 210 MHz (7.69~7.9 GHz) at f1 and f2, respectively.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

One method of estimating the evaporation rate (ER) is to use a variety of evaporation pans, such as the Class A standard evaporation pan (CASEP) and the Colorado Sanken standard evaporation pan (CSSEP). In this study, the rate of evaporation of CASEP and CSSEP have been investigated and compared with each other. This study was conducted in Semnan, Iran. CSSEP was used as a test pan, which was performed in an open space around the Faculty of Civil Engineering, Semnan University. Evaporation was recorded daily for 123 days. The evaporation of the CASEP pan was obtained from the synoptic station of Semnan, which is located at a distance of 2.39 km from the test site. Meteorological data were also obtained from the synoptic station of Semnan and compared with experimental evaporation data. The results of this study showed that the daily ER from CASEP and CSSEP in the tested time periods were not significantly different. Based on the Klomogorov-Sminrov method, the best statistical distributions for CASEP and CSSEP were calculated as Error and Gamma, respectively. The coefficient of determination (R 2 ) between the two pans was estimated to be about 93%. Also, by examining the ER with other meteorological data, it was observed that the ER has the highest correlation with the average daily air temperature.

It is well established that the reaction cycles involving some halogenated alkanes (so-called ozone-depleting substances, ODS) contribute to the depletion of ozone in the stratosphere, thus causing the Montreal Protocol (initially signed in 1987) and later amendments. The Protocol called for the scheduled phase-out of ODS, including chlorofluorocarbons (CFC), hydrochloro-fluorocarbons (HCFC), carbon tetrachloride (CCl4), halon, methyl chloroform (CH3CCl3), me-thyl chloride (CH3Cl), and even hydrofluorocarbons (HFCs). In view of the urgent importance of ozone layer protection to the globally ecological environment, the Taiwan government took regulatory actions on reducing ODS consumption since 1993 by the joint-venture of the central competent authorities. Under the regulatory requirements and the industry’s efforts by adopt-ing the alternatives to ODS and abatement technologies, the phase-out of some ODS (i.e., CFC, CCl4, halon, and CH3CCl3) have been achieved prior to 2010. The consumptions of HCFCs and methyl chloride have been significantly declined over the past three decades (1993-2022). However, HFC emission indicated a V-type variation during the period. Due to the local pro-duction and extensive use of HFC in Taiwan, its emissions increased from 663 kilotons of carbon dioxide equivalents (CO2eq) in 1993 to 2,330 kilotons of CO2eq in 2001, and then decreased to 373 kilotons of CO2eq in 2011. Since then, the emissions of HFC largely used as the alternatives to ODS showed an upward trend, increasing to 1,555 kilotons of CO2eq in 2022. To be in compliance with the Kigali Amendment (KA-2015) to the Montreal Protocol for mitigating global warming, the Taiwan government has taken regulatory actions in reducing the consumption of some HFC substances with high global warming potential (GWP) under the authorization of the Climate Change Response Act in 2023, aiming at the baseline consumption in 2024 by 80 % reduction by 2045.

Background: Whole-body computed tomography (WBCT) is commonly employed for primary screening in pediatric patients experiencing out-of-hospital cardiac arrest (OHCA) without prehospital return of spontaneous circulation (ROSC). This study aimed to evaluate the cause of OHCA on WBCT and compare WBCT findings between ROSC and non-ROSC groups in non-traumatic pediatric OHCA cases in an emergency department (ED) setting. Methods: A retrospective analysis was conducted on 27 pediatric patients (mean age: 32.4 months; median age: 10 months) who experienced non-traumatic OHCA without prehospital ROSC and were transported to our tertiary care hospital between January 2013 and December 2023. WBCT scans were performed to investigate the cause of OHCA, with recorded findings in the head, chest, abdomen, and subcutaneous tissues. Results: In all cases, the direct causes of OHCA were undetermined, and WBCT identified no fatal findings. Statistical comparisons of CT findings between the ROSC and non-ROSC groups revealed significant differences. The non-ROSC group had a higher incidence of brain swelling, loss of cerebral gray-white matter differentiation, symmetrical lung consolidation/ground-glass opacity, cardiomegaly, hyperdense aortic walls, narrowed aorta, gas in the mediastinum, and hepatomegaly compared to the ROSC group. Conclusions: Although WBCT did not provide the direct cause of OHCA, it clarified several indicative findings for non-ROSC. These imaging findings could support clinical decision-making, offering objective criteria for discontinuing resuscitation in pediatric OHCA cases where prehospital ROSC is absent.

The combined effects of global warming and increasing urban heat islands (UHIs) on air temperature and heat stress in cities are notable physical and mental health implications for citizens. With research having shown the effective role of urban green spaces in decreasing urban heat, this study investigated the cooling effect of a large urban park on thermal comfort outside the park area, from psychological and physiological perspectives. The studied park is located in the center of Madrid and adjacent to UHI. The study was performed by conducting field measurements and a survey with questionnaires. The measurements made on six summer days (with two-week intervals) showed that the park’s cooling effect could decrease the air temperature by 2.4-2.8°C right up to the edge of the heat island (600m), and decrease the physiological equivalent temperature (PET) by about 3.9°C. By decreasing air temperature and PET, this park was also shown to increase the perceived thermal comfort (PTC) of the citizens from the psychological perspective in the defined area of effect. This perceived thermal comfort was found to have a significant inverse relationship with PET (P-value <0.05). The examination of cognitive maps drawn by citizens showed that out of the 145 respondents, 68.3% marked the park as the area that they perceive as having the greatest thermal comfort, and prefer as the place to spend time enjoying thermal comfort, irrespective of its distance from their location.

We present a series of computer-assisted high resolution transmission electron (HRTEM) simulations to determine Moiré patters by induced twisting effects between slabs at rotational angles of 3°, 5°, 8°, and 16°, for molybdenum disulfide, graphene, tungsten disulfide, and tungsten selenide layered materials. In order to investigate the electronic structure, a series of numerical simulations using DFT methods was completed using CASTEP with a generalized gradient approximation to determine both band structure and density of states on honeycomb like new superlattices. Our results indicate metallic transitions when rotation approaches 8° with respect to each other for most of the two-dimensional systems that were analyzed.

In this study, a novel task of printing speed optimization for continuous fiber composites is investigated. Using continuous fibers is an innovative approach to reinforce products made by fused filament fabrication (FFF) additive manufacturing (AM) technology. In the printing process of composites with continuous fibers, the printing speed is critical because of its significant effect on the geometric shape of the samples, especially their corners. During optimization in this research, continuous glass fiber (CGF) and polylactic acid (PLA) filaments were utilized as reinforcing phase and matrix, respectively, and were simultaneously fed into the extrusion-based polymer 3D printer to form PLA/CGF composites. The optimization was carried out by calculating the temperature changes of the deposited rasters in the presence and absence of fibers as a first step and then determining the special relationship between the printing speeds and rasters temperature changes. Finally, the optimal and the maximum printing speed was computed based on a hypothesis, which is proved by the results of high-quality printed composites with different geometric shapes.

Agile methods promise to achieve high productivity and provide high-quality software. Agile software development is the most important approach that has spread through the world of software development over the past decade. Software team productivity measurement is essential in agile teams to increase the performance of software development. Due to the prevalence of agile methodologies and increasing competition of software development companies, software team productivity has become one of the crucial challenges for agile software companies and teams. Awareness of the level of team productivity can help them to achieve better estimation results on the time and cost of the projects. However, to measure software productivity, there is no definitive solution or approach whether in traditional and agile software development teams that lead to the occurrence of many problems in achieving a reliable definition of software productivity. Hence, this study aims to propose a statistical model to assess the team’s productivity in agile teams. A survey was conducted with forty software companies and measured the impact of six factors of the team on productivity in these companies. The results show that team effectiveness factors including inter-team relationship, quality conformance by the team, team vision, team leader, and requirements handled by the team had a significant impact on the team’s productivity. Moreover, the results also state that inter-team relations affect the most on software teams’ productivity. Finally, the model fit test showed that 80% of productivity depends on team effectiveness factors.

Background: Smad4, a critical tumor suppressor gene, plays a significant role in pancreatic biology and tumorigenesis. Genetic background and sex are known to influence phenotypic outcomes, but their impact on pancreatic weight in Smad4-deficient mice remains unclear. This study investigates the impact of Smad4 deficiency on pancreatic weight in F1 mice from diverse Collaborative Cross (CC) lines, focusing on the influence of genetic background and sex. Methods: F1 mice were generated by crossbreeding female CC mice with C57BL/6J-Smad4tm1Mak males. Genotyping confirmed the presence of Smad4 knockout alleles. Mice were housed under standard conditions, euthanized at 80 weeks, and their pancreatic weights were measured, adjusted for body weight, and analyzed for effects of Smad4 deficiency, sex, and genetic background. Results: The overall population of F1 mice showed a slight but non-significant increase in adjusted pancreatic weights in heterozygous knockout mice compared to wild-type mice. Sex-specific analysis revealed no significant difference in males but a significant increase in adjusted pancreatic weights in heterozygous knockout females. Genetic background analysis showed that lines CC018 and CC025 substantially increased adjusted pancreatic weights in heterozygous knockout mice. In contrast, other lines showed no significant difference or varied non-significant changes. The interplay between genetic background and sex further influenced these outcomes. Conclusion: Smad4 deficiency affects pancreatic weight in a manner significantly modulated by genetic background and sex. This study highlights the necessity of considering these factors in genetic research and therapeutic development, demonstrating the value of the Collaborative cross-mouse population in dissecting complex genetic interactions.

QSO B0218+357 is a blazar located at a cosmological redshift of 0.944. The source is gravitationally lensed by a spiral galaxy located at the redshift of 0.68. Strong gravitational lensing splits the signals emitted by the source into two components separated by 10-12 days, as observed in radio and gamma-ray bands. In July 2014 a GeV flare was observed by Fermi-LAT, triggering follow-up observations with the MAGIC telescopes at energies above 100 GeV. The expected time delay between the components allowed us to plan broad band MWL observations before, during and after the trailing component of the emission. The MAGIC observations at the expected time of arrival of the trailing component resulted in the first detection of QSO B0218+357 in Very-High-Energy (VHE, >100 GeV) gamma rays. It is both the farthest known VHE object and one of only a few Flat Spectrum Radio Quasars detected in this energy range. We report here the observed multiwavelength spectral and temporal properties of the emission during the 2014 flare.

In this research paper, design and development of pyramidal horn antenna for J-band application is reported. It is particularly designed for 17 dB gain and half beam width about 25 degrees at 6.93 GHz. Horn aperture, horn axial length and distance from the throat of the antenna to aperture are the main design constraints which are calculated and used for the antenna design and simulation. Beam width in E-plane and H-plane horn is calculated and it is 19.18 dB and 22.86 dB respectively. The reported antenna design shows good performance for J-band in radiometry, satellite, and radar applications.

Italian, Spanish, French vs German, Austrian or Norwegian COVID-19 tracks? Antibiotics might have a partial impact on COVID-19 death rates in various countries. Our working hypotheses based on recent publications is that that antibiotics may be a major factor that negatively affects patients’ immune system during viral infections. We are all aware that there is no specific and effective medical treatment for COVID-19 so far. However, we know that our immune system is the only efficient weapon that fights against this syndrome right now. In fact, antibiotics are very often prescribed to prevent secondary infections following an antiviral immune response. Various antibiotic therapies have also been commonly applied to support COVID-19 treatments in China and Italy. Unfortunately, the frequent antibiotic off-site targets include mitochondria that are genetically and evolutionary closely linked to bacteria. Mitochondria are multifunctional organelles responsible for bioenergetics in nearly all our cells, acting as signaling hubs in antiviral and antibacterial immune responses. Several studies have demonstrated that mitochondria are vulnerable to antibacterial treatments, interrupting their physiology. Inhibition of these processes by antibiotics might render the immune system less capable of fighting acute COVID-19 viral infections. Some antibiotics, including those prescribed for COVID-19 in Wuhan, have been shown to inhibit the synthesis of mitochondrial DNA. The question is whether antibiotics support such a treatment or weaken patient immune responses in this case. This hypothesis should be evaluated based on comparative clinical data that seem to be unavailable at the moment. Possibly the COVID-19 risk group should be extended to all patients being treated with antibiotics, including those who finished antibiotic therapies days up to several months before SARS-CoV-2 infection. We therefore urge health service response groups to evaluate the impact of antibiotics on COVID-19 recovery vs death retrospective data. We would like to motivate international, national and local health authorities to share available clinical treatment data, discuss and optimize treatment strategies.

The diffusion of molecules in aqueous solutions in the domain of membrane technology is very critical in the efficiency of chemical engineering and purification processes. In this study, the diffusion in high and low concentration regions is simulated with finite difference method (FDM), and then the results of numerical computations are coupled with adaptive network-based fuzzy inference system (ANFIS) and bilayered neural network method (BNNM). Machine learning approach can individually predict diffusion phenomena across the domain based on understanding of the machine instead of the discretization of an ordinary differential equation (ODE). The findings of the machine learning method are in good agreement with those of FDM at different times of the simulation. In addition to numerical computation, the error of the system is computed for different iterations. The results show that by increasing the number of iterations and training datasets, all errors reduce significantly for both training and testing. BNN method is also used to train the prediction process of diffusion for a more accurate comparison. This technique is similar to ANFIS method in terms of prediction capability. According to the findings, ANFIS approach predicts diffusion slightly better than BNN method. In this regard, ANFIS technique produces R>0.99 while BNN method produces R around 0.98. Both machine learning methods are accurate enough to predict diffusion throughout the domain for different time steps. The computational time for both algorithms is less than that of FDM method to predict low and high concentrations in the domain. Besides, based on the results, artificial intelligence (AI) can find the relationship between inputs and outputs and determine which input has the main influence on the output in this study to optimize the process. As such, future studies can be focused on AI and other methods for faster prediction and optimization processes.

Variable cross-section arch is widely used in practical engineering because of its beautiful arc and excellent mechanical properties. However, there is still no systematic and comprehensive study on the out-plane buckling of variable cross-section arch. In view of this, this paper is concentrated on an elastic analytical research of out-plane buckling of arches with variable cross-section under a uniformly distributed radial local load. The pre-buckling and out-plane buckling behaviour of a variable cross-sectional arch under an external load is quite different from that of an arch with uniform cross-section. The Castigliano's second theorem is used to establish pre-buckling force method equilibrium equations for variable cross-sectional arches under a uniformly distributed radial local load, and corresponding analytical solutions of normal stress, axial compression and the bending moment are obtained. Based on the energy method and the Ritz method, analytical solutions of the critical load for the elastic out-plane buckling of arches with variable cross-section are derived. Comparisons with ANSYS results indicated that the analytical solutions are able to accurately predict the pre-buckling internal forces and critical out-plane buckling load of variable cross-section arches subjected to a uniformly distributed radial local load. It is found that the internal forces and the out-plane buckling load of an arch are significantly affected by the variation of cross-sectional height. With the ratio of cross-sectional height of the top to the end increase, the bending moment decreases and the axial force and critical out-plane buckling load increase. Analytical solutions of pre-buckling internal force and critical out-plane buckling load problems for arches with variable cross-section have a wider significance, since they can provide an effective explicit analytic method for the optimal design of arch structure.

The Leave-One-Out (LOO) Green Fluorescent Protein (GFP) approach to biosensor design com-bines computational protein design with split protein reconstitution. LOO-GFPs reversibly fold and gain fluorescence upon encountering its target peptide, which can be redefined by computa-tional design of the LOO site. Such an approach can be used to create reusable biosensors for the early detection of emerging biological threats. Enlightening biophysical inferences for nine LOO-GFP biosensor libraries are presented, with target sequences from dengue, influenza, or HIV, replacing beta strands 7, 8 or 11. An initially low hit rate was traced to components of the energy function, manifesting in the over-rewarding of over-tight side chain packing. Also, screening by colony picking required a low library complexity, but designing a biosensor against a peptide of at least 12 residues requires a high complexity library. This double-bind was solved using a "piecemeal" iterative design strategy. Also, designed LOO-GFPs fluoresced in the unbound state due to unwanted dimerization, but this was solved by fusing a fully functional prototype LOO-GFP to a fiber-forming protein, Drosophila ultrabithorax, creating a biosensor fiber. One in-fluenza hemagglutinin biosensor is characterized here in detail, showing a shifted excita-tion/emission spectrum, a micromolar affinity for the target peptide, and an unexpected pho-to-switching ability.

To enhance the uplift capacity and facilitate the installation of multi-row perfobond connectors at shallow burial depths, this study puts forward a novel notched T-perfobond connector. The design incorporates an integrated flange at the bottom of the connector and a notch at the edge of the hole. Through pull-out model tests on four notched T-perfobond connectors, this research investigates their failure mechanisms and pull-out capacities. Utilizing the explicit dynamics method in Abaqus, a finite element model of the pull-out resistance test for the notched T-perfobond connector is established and verified against experimental data. Furthermore, a detailed parametric analysis involving 54 models is conducted, examining crucial parameters such as rib dimensions, hole geometry, flange size, notch width, bar diameter, and material properties. Based on the combined experimental and numerical results, the paper assesses the suitability of current formulas for calculating the pull-out capacity of perfobond connectors and proposes a refined calculation method specifically for notched T-perfobond connectors. All the findings in this paper can serve as a reference in the design and construction of composite structures.

Skin cancer is an exquisite disease globally nowadays. Because of the poor contrast and apparent resemblance between skin and lesions, automatic identification of skin cancer is complicated. The rate of human death can be massively reduced if melanoma skin cancer can be detected quickly using dermoscopy images. In this research, an anisotropic diffusion filtering method is used on dermoscopy images to remove multiplicative speckle noise and the fast-bounding box (FBB) method is applied to segment the skin cancer region. Furthermore, the paper consists of two feature extractor parts. One of the two features extractor parts is the hybrid feature extractor (HFE) part and another is the convolutional neural network VGG19 based CNN feature extractor part. The HFE portion combines three feature extraction approaches into a single fused feature vector: Histogram-Oriented Gradient (HOG), Local Binary Pattern (LBP), and Speed Up Robust Feature (SURF). The CNN method also is used to extract additional features from test and training datasets. This two-feature vector is fused to design the classification model. This classifier performs the classification of dermoscopy images whether it is melanoma or non-melanoma skin cancer. The proposed methodology is performed on two ordinary datasets and achieved the accuracy 99.85%, sensitivity 91.65%, and specificity 95.70%, which makes it more successful than previous machine learning algorithms.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

The current emphasis in the advancement of space-based synthetic aperture radar (SAR) is on lightweight payloads under 100kg with resolutions surpassing 1m. This focus is directed towards meeting the launch criteria for multiple satellites on a single rocket and cutting costs. This article discusses the creation and progress of a Ku-band SAR payload for the Taijing-4(03) Satellite, launched on January 23, 2024 accompanied by four other satellites. The SAR payload design was customized to meet the demands of a micro-nano satellite platform, resulting in a lightweight, flat design weighing less than 80kg, seamlessly integrated with the plate-shaped satellite platform. The article also introduces a beam optimization strategy for the phased array SAR antenna, significantly boosting the SAR system’s performance. The SAR payload provides various operating modes like slide-spot, strip, scan 1, scan 2, and others, with a maximum achievable resolution exceeding 1m. Extensive in-orbit testing of the payload produced numerous high-quality SAR images with potential uses in emergency disaster mitigation, safeguarding ecosystems, monitoring forests, managing crops, tracking sea ice, and more.

Silicon photonics is emerging as a competitive platform for electronic-photonic integrated circuits (EPICs) at the 2 µm wavelength band where GeSn photodetectors (PDs) have proven to be efficient PDs. Here, we present a comprehensive theoretical study of GeSn vertical p-i-n homojunction waveguide photodetectors (WGPDs) that have a strain-free and defect-free GeSn active layer for 2-µm Si-based EPICs. The use of a narrow-gap GeSn alloy as the active layer can fully cover entire the 2 µm wavelength band. The waveguide structure allows for decoupling the photon-absorbing path and the carrier-collection path, thereby allowing for simultaneous achievement of high-responsivity and high-bandwidth (BW) operation at the 2-µm wavelength band. We present the theoretical models to calculate the carrier saturation velocities, optical absorption coefficient, responsivity, 3-dB bandwidth, zero-bias resistance, and detectivity, and optimize this device structure to achieve highest performance at the 2-µm wavelength band. The results indicate that the performance of the GeSn WGPD has strong dependence on the Sn composition and geometric parameters. The optimally designed GeSn WGPD with 10% Sn concentration can give responsivity of 1.55 A/W, detectivity of 6.12×1010 cmHz½W-1 at 2 µm wavelength, and ~97 GHz BW. Therefore, this optimally designed GeSn WGPD is a potential candidate for silicon photonic EPICs offering high-speed optical communications.

In this short communication, we conducted first-principles calculations to explore the stability of boron monochalcogenides (BX, X=S, Se or Te), as a new class of two-dimensional (2D) materials. We predicted BX monolayers with two different atomic stacking sequences of ABBA and ABBC, referred in this work to 2H and 1T, respectively. Analysis of phonon dispersions confirm the dynamical stability of BX nanosheets with the both 2H and 1T atomic lattices. Ab-initio molecular dynamics simulations reveal the outstanding thermal stability of all predicted monolayers at high temperatures over 1500 K. BX structures were found to exhibit high elastic modulus and tensile strengths. It was found that BS and BTe nanosheets can show high stretchability, comparable to that of the graphene. It was found that all predicted monolayers exhibit semiconducting electronic character, in which 2H structures present lower band-gaps as compared with 1T lattices. The band-gap values were found to decrease from BS to BTe. According to the HSE06 results, 1T-BS and 2H-BTe show respectively, the maximum (4.0 eV) and minimum (2.06 eV) electronic band-gaps. This investigation introduces boron monochalcogenides as a novel class of 2D semiconductors with remarkable thermal, dynamical and mechanical stability.

Abstract: Insecure and portable devices in the smart city’s Internet of Things (IoT) network are increasing at an incredible rate. Various distributed and centralized platforms against cyber-attacks have been implemented in recent years, but these platforms are inefficient due to their constrained levels of storage, high energy consumption, the central point of failure, underutilized resources, high latency, and etc. In addition, the current architecture confronts the problems of scalability, flexibility, complexity, monitoring, managing & collecting of IoT data, and defend against cyber-threats. To address these issues, the author presents distributed and decentralized Blockchain-Software Defined Networking (SDN) based energy-optimized architecture for IoT in smart cities. Thus, SDN continuous observing, controlling, managing IoT devices activities and detect possible attacks in the network; Blockchain provides adequate security & privacy against cyber-attacks, reduces the central point of failure issues; Network Function Virtualization (NFV) are used to saving energy, load balancing, as well as increasing the lifetime of the entire network. Also, we introduce a Cluster Head Selection (CHS) algorithm to reduce the energy consumption in the presented model. Finally, we analyze the performance using various parameters (e.g. throughput, response time, gas consumption, communication overhead) and demonstrating the result that provides higher throughput, lower response time, lower gas consumption than existing works for smart cities.

Electroencephalography (EEG) is a brain imaging technique in which electrodes are placed on the scalp. EEG signals are commonly decomposed into frequency bands called delta, theta, alpha, and beta.While these bands have been shown to be useful for characterizing various brain states, their utility as a one-size-fits-all analysis tool remains unclear. We present a two-part data-driven methodology for objectively determining the best EEG bands for a given dataset in this paper. First, a decision tree is used to estimate the optimal frequency band boundaries for reproducing the signal’s power spectrum for a predetermined number of bands. The optimal number of bands is then determined using an Akaike Information Criterion (AIC)-inspired quality score that balances goodness-of-fit with a small band count. Data-driven EEG band discovery may aid in objectively capturing key signal components and uncovering new indices of brain activity.

Spending on out-patient health care by citizens in limited resource countries has received little attention.The purpose of this study is to determine the predictors of household spending on out-patient expenses in a cross-sectional study in Kenya. We applied the GEE methods to determine the effect of various variables on outpatient care. We established that the best predictors for outpatient spending in Kenya are Age of the household head, wealth index, marital status and education, which had the lowest QICu of 976341.2. There were no differences on age in mean spending on outpatient care and was changing in a sinusoidal manner. The rich spend more on outpatient care, due to financial ability. Spending increased across the wealth quantiles while gender had a significant effect in the general performance of the models, it didn’t assist in lowering the QICu

Auto checkout has received more and more attention in recent years and this system automatically generates a shopping bill by identifying the picture of the products purchased by the customers. However, the system is challenged by the domain adaptation problem, where each image of the training set contains only one commodity, whereas the test set is a collection of multiple commodities. The existing solution to this problem is to resynthesize the training images to enhance the training set. Then the composite images are rendered using CycleGAN to make the image distribution of the training set and the test set more similar. However, we find that the detection boxes given by the ground truth of the common dataset contain a large part of the background area, the area will affect the training process as noise. To solve this problem, we propose a mask data priming method. Specifically, we redo the large scale Retail Product Checkout (RPC) dataset and add segmentation annotation information to each item in the training set image based on the original dataset using pixel-level annotation. Secondly, a new network structure is proposed in which we train the network using joint learning of detectors and counters, and fine-tune the detection network by filtering out suitable images from the test set. Experiments on the RPC dataset have shown that our method yields better results. we used an approach that reached 81.87% compared to 56.68% for the baseline approach which demonstrates that pixel-level information helps to improve the detection results of the network.

Early diagnosis, prioritization, screening, clustering and tracking of COVID-19 patients, and production of drugs and vaccines are some of the applications that have made it necessary to use a new style of technology to involve, to manage and deal with this epidemic. Strategies backed by artificial intelligence (AI) and the Internet of Things (IoT) have been undeniable to understand how the virus works and try to prevent it from spreading. Accordingly, the main aim of this survey article is to highlight the methods of ML, IoT and the integration of IoT and ML-based techniques in the applications related to COVID-19 from the diagnosis of the disease to the prediction of its outbreak. According to the main findings, IoT provided a prompt and efficient approach of following the disease spread. Most of the studies developed by ML-based techniques for handling COVID-19 based dataset provided performance criteria. The most popular performance criteria, is related to accuracy factor. It can be employed for comparing the ML-based methods with different datasets. According to the results, CNN with SVM classifier, Genetic CNN and pre-trained CNN followed by ResNet, provided highest accuracy values. On the other hand, the lowest accuracy was related to single CNN followed by XGboost and KNN methods.

This paper provides the state of the art of data science in economics. Through a novel taxonomy of applications and methods advances in data science are investigated. The data science advances are investigated in three individual classes of deep learning models, ensemble models, and hybrid models. Application domains include stock market, marketing, E-commerce, corporate banking, and cryptocurrency. Prisma method, a systematic literature review methodology is used to ensure the quality of the survey. The findings revealed that the trends are on advancement of hybrid models as more than 51% of the reviewed articles applied hybrid model. On the other hand, it is found that based on the RMSE accuracy metric, hybrid models had higher prediction accuracy than other algorithms. While it is expected the trends go toward the advancements of deep learning models.

In this work, backscattering signatures of snow-covered lake ice and sea ice from X- and Ku-band synthetic aperture radar (SAR) data are investigated. The SAR data were acquired with the ESA airborne SnowSAR sensor in winter 2012 over Lake Orajärvi in northern Finland and over landfast ice in the Bay of Bothnia of the Baltic Sea. Co-incident with the SnowSAR acquisitions in-situ snow and ice data were measured. In addition, time series of TerraSAR-X images and ice mass balance buoy data were acquired for the Lake Orajärvi in 2011-12. The main objective of our study was to investigate relationships between SAR backscattering signatures and snow depth over lake and sea ice, with the ultimate objective of assessing the feasibility of retrieval of snow characteristics using X- and Ku-band dual-polarisation (VV and VH) SAR over freshwater or sea ice. This study constitutes the first comprehensive survey of snow backscattering signatures at these two combined frequencies over both lake and sea ice. For lake ice, we show that X-band VH-polarized backscattering coefficient (σo) and the Ku-band VV/VH-ratio exhibited the highest sensitivity to the snow depth. For sea ice, the highest sensitivity to the snow depth was found from the Ku-band VV-polarised σo and the Ku-band VV/VH-ratio. However, the observed relations were relatively weak, indicating that at least for the prevailing snow conditions, obtaining reliable estimates of snow depth over lake and sea ice would be challenging using only X- and Ku-band backscattering information.

Through the use of machine learning algorithms like the Support Vector Machine, it has been show that burn extent can be accurately mapped from hyperspatial drone imagery in both grasslands and forests. Despite these successes, hyperspatial imagery must be acquired via drones, requiring large amounts of time and resources to capture areas much smaller than the large catastrophic fires which result in the majority of the lands burned each year by wildland fires. To overcome this difficulty, high spatial resolution satellite imagery from Worldview2 can be substituted for hyperspatial drone imagery, allowing for larger regions of images to be acquired more easily and efficiently. Additionally, Worldview2 trades spatial resolution for spectral resolution and extent, capturing images in 8 multispectral bands as opposed to 3 band imagery in the visible spectra. This research examines the utility of each of the 8 bands observed in Worldview2 imagery using an Iterative Dichotomiser 3 decision tree, then uses these bands to map burn extent and biomass consumption. Several classifications of burn extent and biomass consumption are produced and compared based on the bands used as inputs. The results show that using Worldview2 imagery to map burn extent and biomass consumption results in highly accurate maps, with slight improvements when additional bands are added.

Knowing that biomolecules, such as β-amyrin and α-amyrin, have some pharmacological effects, the aim of this study was directed towards exploring the protective effect of a Tomato Peel and Seed Extract (TPSE) for its soothing function but also for its capacity to modulate the adrenal axis, involved in stress response. Ex vivo tests were carried out on skin explants to evaluate the effectiveness of TPSE formulated at 0.5% on Calcitonin Gene-Related Peptide (CGRP) and IL-10 release, Kappa Opioid Receptor (KOR) and Caspase 14 expression. An in vivo study combined a clinical evaluation of skin homogeneity, psychological parameter as well as analysis of salivary cortisol and dehydroepiandrosterone concentrations. All measurements were carried out at the beginning and after 28 days of applying a TPSE face cream. TPSE regulated not only the release of CGRP and Il-10, reflecting an anti-neurogenic and anti-inflammatory properties, but also modulated KORs. Twenty height days of TPSE application induced a significant decrease in intensity and extent erythrosis, a lower output of salivary cortisol and a significant increase in pleasant emotions when compared to placebo. These results provide encouragement to continue exploring the impact of cosmetic ingredient on psychophysiological parameters to improve skin health and well-being.

To understand the possibility of interaction between scientific experimenting and artistic drawing in the form of drawings made in notebooks, assumed is a common element, a spiritual property, and transference as a mechanism for causality. Scientists, scientific experiments and artistic drawings all have different merits. Here the concept ‘speaking out’ in its meaning of expressiveness is proposed to bridge these differences. Scientific action and artistic action cannot be compared directly. However, a common spiritual element will make the investigated object, experimental set-up and notebook drawings comparable in the sense of translations authorized by the physicist. They all then speak out from the same source. In this paper considered are recent drawings made by physicists during experimentation, in notebooks and diaries. Discussed is transferal causality between the physicist, the artistic drawing and all the relevant objects belonging to the experiment. Spiritual properties are introduced for the physicist being a person, and for the investigated object, the experimental set-up and the drawings as objects.

Efficient beam steerable high-gain antennas enable high-speed data rates over long-distance networks, including wireless backhaul, satellite communications (SATCOM), and SATCOM On-the-Move. These characteristics are essential for advancing contemporary wireless communication networks, particularly within 5G and beyond. Various beam-steering solutions have been proposed in the literature, with passive beam-steering mechanisms employing planar metasurfaces emerging as cost-effective, power-efficient, and compact options. These attributes make them well-suited for use in confined spaces, large-scale production and widespread distribution to meet the demands of the mass market. Utilizing a dual-band antenna terminal setup is often advantageous for full duplex communication in wireless systems. Therefore, this article presents a comprehensive review of the dual-band beam steering techniques for enabling full-duplex communication in modern wireless systems, highlighting their design methodologies, scanning mechanisms, physical characteristics, and constraints. Despite the advantages of planar metasurface-based beam steering solutions, literature on dual-band beam steering antennas supporting full duplex communication is limited. This review article identifies research gaps and outlines future directions for developing economically feasible passive dual-band beam-steering solutions for mass deployment.

We investigate the tunneling of quasiparticles through a potential barrier of finite height and width, in a system with a band structure consisting of a quadratic band crossing point (QBCP). We compute the results of the transmission coefficient at various incident angles, and also the conductivity and the Fano factor. We discuss the distinguishing signatures of these transport properties in comparison with other semimetals, as well as electrons in normal metals.

Indications of the passage of time are indirect reminders of our mortality. Humans have often responded to this discomforting thought by attempting, temporally at least, to escape its relentless march through the notion of a timeless present. This essay explores how architecture can assist us in that objective. It suggests that there are at least three different ways that buildings can offer us temporary psychological refuge from the progress of time. They can include the fascination of seemingly timeless natural movement patterns. They can recall archetypal environments, and they can isolate us from the external world of perpetual temporal progress.

Three ternary mixtures composed by choline chloride (ChCl), ethylene glycol (EG) and a second hydrogen bond donor (HBD) as ethanol (A), 2-propanol (B), and glycerol (C) were studied in terms of composition related to the band gap energy (BGE). A Design of Experiments (DoE) approach, and in particular a Simple Lattice three-components design, was employed for determining the variation of the BGE upon the composition of each system. UV-VIS analysis and subsequent Tauc plot methodology provided the data requested from the DoE and multivariate statistical analysis revealed a drop of the BGE in correspondence to specific binary compositions for systems A and B. In particular, a BGE of 3.85 eV was registered for the mixtures ChCl/EtOH (1:1), and ChCl/2-propanol (1:1), which represents one of the lowest values ever observed for these systems.

Social capital creates a synergy that brings many benefits to members of a community. Thus, the main objective of this article was to examine whether social capital can improve a society's food security. If yes, how? To answer these questions, a systematic literature review was conducted using the Prisma approach. The output of this method led to finding 39 related articles. Precise studying these articles illustrated that social capital improves food security through two mechanisms of knowledge sharing and product sharing (i.e., sharing food products). It revealed that social capital through improving the food security pillars (i.e., food availability, food accessibility, food utilization, and food system stability) affects food security. In other words, the interaction among the members of the community results in sharing food products and information among community members, and this facilitates food availability and access to food. There are many shreds of evidence in the literature that sharing food and food product among the community member decreases household food security and provides the healthy nutrition to the vulnerable families and improve the food utilization pillar of food security. In addition, it is disclosed that belonging to the social networks increases the resilience of the community members and decreases the vulnerability of the community that subsequently strengthens the stability of a food system. This study contributes to the common literature on food security and social capital by providing a conceptual model based on the literature. In addition to researchers, policymakers can use the finding of this study to provide solutions to address food insecurity problems.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

This work analyzes the severity and risk associated with Automatic Dependent Surveillance-Broadcast (ADS-B) message drop out in Detect and Avoid (DAA) function of Unmanned Aircraft System (UAS). Performance assessment of the Universal Access Transceiver (UAT) ADS-B message implies that in some cases ADS-B fails to update within a specified update interval, which is referred to as drop out in this work. ADS-B is a fundamental surveillance sensor for both class 1 and class 2 DAA systems. Message loss or drop out has been found as one of the common limitations of the ADS-B system. The key feature of this study is incorporating the update rate of real ADS-B data transmitted from the manned aircraft. The data were received from the Grand Forks International Airport, North Dakota. Monte Carlo method has been adopted to resolve encounter scenarios in the presence of drop out. The change in the alert triggered by the UAS DAA in the presence of ADS-B drop out has been investigated. Furthermore, the risk matrices are created to quantify the associated risk with drop out affected alerts. Simulation results depict that both the duration of drop out and DAA look-ahead time affect the alert-triggering function of UAS. With a small look- ahead window and longer duration of drop out, the number of warning alerts increases. Also, alerts are affected more during an overtaking encounter than that of a head-to-head encounter. A system-level analysis is also carried out to recognize the potential reasons behind the ADS-B drop out.

In this paper, we investigate the so-called electronic dressed states, a unified quasiparticle resulting from the interaction between electrons in a two-dimensional material with an off-resonance optical dressing field. If the frequency of this field is much larger than all characteristic energies in the system, such as the Fermi energy or bandgap(s), the electronic band structure is affected by radiation so that some important properties of the electron dispersions could be modified in a way desirable for practical applications. For example, a circularly polarized light can be used to vary the bandgap of Dirac materials: it opens a gap in graphene and other metallic and semimetallic lattices, or modifies the magnitude of an existing gap. This will either enhance or reduce a gap, depending on its initial value as well as properties of a host material. Here, we consider gaped dice and Lieb lattices as samples, and put forward a full theoretical model to reveal how these electronic states are deformed by an elliptically-polarized irradiation with a focus on generation and modification of a bandgap.

This work presents preliminary experimental results advancing non-destructive testing methods for detecting steel bars in concrete structures via contactless investigation in the X-band spectrum. The study reveals the field’s penetration into concrete, extracting insights into embedded bars through scattered data. Applying a quasi-quadratic inverse scattering technique to numerically simulated data yields promising results, confirming the effectiveness and reliability of the proposed approach. In this realm, using a higher frequency allows the use of lighter equipment and smaller antennas. Identified areas for improvement include accounting for antenna behavior and establishing undeformed target morphology and precise orientation. Transitioning from powder-based and sand specimens to real solid reinforced concrete structures is expected to alleviate laboratory challenges. Although accurately determining concrete properties such as relative permittivity and conductivity is essential, it remains beyond the scope of this study. Finally, overcoming these challenges could significantly enhance non-invasive testing, improving structural health monitoring and disaster prevention.

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

The unfolded band structure and optical properties of Cu-doped KCl crystals were computed by first principles within the framework of density functional theory, implemented in the ABINIT electronic structure package utilizing pseudopotential approximation and a plane-wave basis set. From a theoretical point of view, Cu substitution into pristine KCl crystals requires calculation by the supercell (SC) method. This procedure shrinks the Brillouin zone, resulting in a folded band structure that is difficult to interpret. To solve this problem and gain insight into the effect of copper ions (Cu+) on electronic properties, the band structure of SC KCl:Cu was unfolded to make a direct comparison with the band structure of the primitive cell (PC) of pristine KCl. To understand the effect of Cu substitution on optical absorption, we calculated the imaginary part of the dielectric function of KCl:Cu through a sum-over-states formalism and broke it down into different band contributions by partially making an iterated cumulative sum (ICS) of selected valence and conduction bands. Consequently, we identified those interband transitions that give rise to the absorption peaks due to the Cu+ ion. These transitions involve valence and conduction bands formed by the Cu-3d and Cu-4s electronic states

Coffee and caffeine have been used as solar absorbers and also to increase the thermal stability and efficiency of perovskite solar cells. In this work, we report the sensing of extremely alkaline pH by colloidal coffee solution aided by generation of an optical absorption band in the near-UV region. This generation of absorption band could be explained by the orientation induced dipole-dipole interactions arising from differing caffeine-solvent interactions with varying pH. Such a generation leads to the lowering of direct as well as indirect bandgaps from 4 eV-->2.8 eV& 3.4 eV-->2.5 eV, respectively. We also estimate the changes in optical energy storage efficiency, inferring it to be highest for pH 11 having the highest intensity of the generated absorption band (λ_abs≈360 nm). With these observations and further deductions, the work reported in this paper would be of immense interest to the researchers working in the field of development of chemical pH sensors and also in the development of novel UV absorbers.

Induction machines drive many industrial processes, and their unexpected failure can cause heavy production losses. The analysis of the current spectrum can identify online the characteristic fault signatures at an early stage, avoiding unexpected breakdowns. Nevertheless, frequency domain analysis requires stable working conditions, which is not the case for wind generators, motors driving varying loads, etc. In these cases an analysis in the time-frequency domain -such as a spectrogram- is required for detecting faults signatures. The spectrogram is built using the short frequency Fourier transform, but its resolution depends critically on the time window used to generate it: short windows provide good time resolution, but poor frequency resolution, just the opposite than long windows. Therefore, the window must be adapted at each time to the shape of the expected fault harmonics, by highly skilled maintenance personnel. In this paper, this problem is solved with the design of a new multi-band window, which generates simultaneously many different narrow-band current spectrograms, and combines them into a single, high resolution one, without the need of manual adjustments. The proposed method is validated with the diagnosis of bar breakages during the start-up of a commercial induction motor.

Context: A clinical video telehealth (CVT) program was implemented improve access and quality of dementia care to patients and their caregivers in rural areas. The program was offered as part of an established dementia clinic/geriatric primary care clinic in collaboration with five community-based outpatient clinics (CBOC’s) affiliated with the Tennessee Valley Healthcare System (TVHS) in middle Tennessee. Telehealth support was provided by a physician – social worker team visit. Methods: Telehealth training and equipment were provided to clinic personnel, functioning part-time with other collateral clinical duties. Patients and caregivers were referred by primary care providers and had an average of 1 to 2 CVT encounters originating at their local CBOC lasting 20 to 30 minutes. Clinical characteristics and outcomes of patients and caregivers receiving CVT support were collected by retrospective electronic medical record (EMR) review. Results: Over a 3-year period 45 CVT encounters were performed on patient-caregiver pairs, followed for a mean of 15 (1-36) months. Some 80% patients had dementia confirmed and 89% of these had serious medical comorbidities, took an average of 8 medications, and resided at a distance of 103 (76-148) miles from the medical center. Dementia patients included 33% with late stage dementia, 25% received additional care from a mental health provider, 23% took antipsychotic medications, 19% transitioned to a higher level of care, and 19% expired an average of 10.2 months following consultation. Caregiver distress was present in 47% of family members. Consult recommendations included 64% community-based long-term care services and supports (LTSS), 36% medications, and 22% further diagnostic testing. Acceptance of the CVT encounter was 98%, with 8770 travel miles saved. Conclusion: CVT is well received and may be helpful in providing dementia care and supporting dementia caregivers to obtain LTSS for high-need older adults in rural areas.

This paper elucidates the impact of uncertainty on the Markowitz asset allocation and how it performs. The findings imply that when evaluated out-of-sample, estimation errors in parameters might significantly affect how well an allocation performs. Numerous publications that address this ambiguity have been highlighted to emphasize our findings further. In our work, we compare these approaches to alternative allocation strategies and explain their performance in both expected and real out-of-sample events. We find that the Markowitz framework can be improved by using tactics that take uncertainty into account. Longer sample numbers, however, may not always translate into better outcomes. Applying a short-sale constraint can also enhance the initial portfolio. Finally, we find that even more basic approaches to asset allocation, such as equally weighted allocation, perform reasonably well.

Nurses focus more on curative aspects rather than health promotion and disease prevention, thus weakening primary health care and lessening engagement with the community. Providing a learning environment that can support the professional growth of nurses through engagement with local communities and educational institutions would strengthen primary health care in the community; however, this poses challenges due to the traditional mindset of nurses towards primary health care. This integrative review aimed to explore key features of the potential of the nursing center model as a contracting-out approach to strengthen primary health care services. This integrative review provides lessons for implementing the Nursing Centre model for any country, mainly where nurses are not fully utilized for health promotion and disease prevention.

Background: The ongoing outbreak of Coronavirus Disease 2019 (COVID-19) represents a major threat to human health, which impairs the functionality of several organs. One of the hardest challenges in the fight against COVID-19 is the development of wide-scale, effective, and rapid laboratory tests to control disease severity, progression, and possible sudden worsening. Monitoring patients in real-time is indeed highly demanded in this pandemic era when physicians need reliable and quantitative tools to prioritize patients’ access to intensive care departments. In this regard, salivary biomarkers are extremely promising, as they allow for a fast and non-invasive specimens’ collection, which can be repeated multiple times. Methods: We compare salivary levels of immunoglobulin A subclasses (IgA1 and IgA2) and free-light chains (FLC k and λ) in a cohort of 29 SARS-CoV-2 patients and 21 healthy subjects. Results: We found that each biomarkers differs significantly between the two groups, with p-values ranging from 10-8 to 10-4. The performance ranking of these markers, shows that λFLC level (p=1.4e-8) is the best-suited candidate to discriminate the two groups, with an accuracy of 0.94 (0.87-1.00 95% CI), a precision of 0.91 (0.81-1.00 95% CI), a sensitivity of 1.00 (0.96-1.00 95% CI) and a specificity of 0.86 (0.70-1.00 95% CI). Conclusion: These results suggest λFLC as an ideal indicator of patient conditions. This is more strengthened in consideration that λFLC half-life (approximately 6 hours) is significantly shorter than the IgA one (21 days): thus λFLC appears displaying the potential to effectively monitor patients fluctuation in real-time.

This study aims to introduce out of school activities (OSA) to high school PJOK teachers in Padang Pariaman District, West Sumatra Province, Indonesia. As is known, OSA is an alternative for students in fulfilling their movement needs, especially during the COVID 19 pandemic. Currently, students mostly stay at home, such as studying from home, to doing activities from home. So that there is minimal possibility of carrying out the movement activities recommended by WHO. The research method used is action research. This method gets a problem, then arranges problem-solving, conducts treatment, and finally evaluates. The research results show no teachers who have ever carried out of school activities (OSA); understanding, implementation, and evaluation are also not understood by the teachers. After being given the treatment, the teachers became more aware and understood about out of school activities, starting from understanding, implementing to evaluating what had to be done.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

Three cases of Day-Night Band (DNB) observations of the Visible Infrared Imaging Radiometer Suite (VIIRS) onboard the Suomi National Polar-orbiting Partnership (SNPP) are explored for applications to assess the ocean environment and monitor ocean dynamics. An approach to use the DNB radiance ratio was developed in order to better continuously assess the ocean diurnal and short-term environmental changes with VIIRS DNB observations. In the La Plata River Estuary, the sediment fronts showed 20–25 km diurnal inshore-offshore movements on March 13, 2017. In the waters off the Argentina coast in the South Atlantic, VIIRS DNB measurements provided continuous observations and monitoring of the algae bloom development and migration between 24–26 March 2016. This algae bloom generally kept the same spatial patterns, but moved nearly 20 km eastward in the three-day period. In the Yangtze River Estuary and Hangzhou Bay region in China’s east coast, VIIRS DNB observations also revealed the complicated coastal dynamic changes between 12–14 April 2017. Even though there are still some challenges and limitations for monitoring the ocean environment with VIIRS DNB observations, this study shows that satellite DNB observations can provide additional data sources for ocean observations, especially observations during the nighttime.

The purpose of this study is to improve the performance of walls under out-of-plane loads, particularly when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented here consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM system and the CFRP strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques: the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is ductile as for the specimens reinforced with the CAM system. They also allowed us to design a more performing combined technique.

In recent years, pedestrian re-identification has gained a lot of interest due to its importance for many purposes such as security and safety. Many types of solutions have been proposed to solve this problem, where the majority are based on a features extraction such Convolution Neural Networks (CNNs). These approaches assume that only the identities that are in the training data can be recognized. The pedestrians in the training data are called In distribution (ID). However, in real world scenarios, new pedestrians and objects can appear in the scene and the model should detect them as Out Of Distribution (OOD). In our previous study , we proposed a pedestrian re-identification based on von-Mises Fisher (vMF) distribution. Each identity is embedded in the unit sphere as a compact vMF distribution far from other identities distributions. The embedding is done through a base CNN. Recently, proposed a framework called Virtual Outlier Synthetic (VOS), that detects OOD based on synthesising virtual outlier in the embedding space in an online manner. Their approach assumes that the samples from the same object maps to a compact space. This assumption aligns with the vMF based approach. Therefore, in this paper, we revisited the vMF approach and merged with VOS in order to detect OOD data points. We present our approach to merge both frameworks. We conducted several experiments to evaluate our proposed framework. Results showed that our framework was able to detect new pedestrian that do not exist in the training data in the inference phase. It also slightly helped to improve the re-identification performance.

The purpose of this study was to assess the extent to which self-esteem and depression mediated the influence of internalized stigma on life satisfaction among Korean out-of-school youths. Cross-sectional data on 318 youths provided information on perceived stigma, self-esteem, depression, life satisfaction, and personal characteristics. A multinomial logistic regression analysis was followed by structured path analysis to investigate the mediation effects. Internalized stigma was negatively associated with life satisfaction. Self-esteem significantly mediated the influence of stigma on depression and the influence of depression on life satisfaction. Further, stigma directly and significantly influenced depression. This study demonstrated that self-esteem and depression were important to the relationship between internalized stigma and life satisfaction. Implications for possible policies and programs with the aim of helping out-of-school youths to integrate and lead successful satisfying lives are discussed.

The electronic structure and some of its derived properties of Li2CaGeO4 compound have been investigated. The calculations have been performed using the full-potential linearized augmented plane wave plus local orbitals method and ultra-soft pseudo-potentials . The optimized lattice parameters are found to be ingood accord with experiment. Features such as bulk modulus and its pressure derivative, electronic band structure and density of states are reported. The elastic anisotropy of the crystal is discussed and visualized. Moreover, the optical properties reveal that Li2CaGeO4 compound are suitable candidates for optoelectronic devices in the visible and ultraviolet (UV) regions.

We propose a novel plasmon nano-optical antenna that consists of three vertically superimposed discs with different materials. Two symmetrical nanometer-scale Yagi antenna elements with gold-material are embedded into the surface of the middle disc with silicon dioxide. Based on plasmon theory and Yagi antenna principle, we explore the properties of the far-field radiation and near-field transmission of the antenna in near infrared band. It is found that the pattern of the xoy plane in the antenna can be adjusted in arbitrary direction. The far-field pattern and near-field transmission spectrum can be reconfigured by changing the angle a of the Yagi antenna elements in the middle disc. Moreover, we also discuss the influences of the widths and lengths of the elements on the near-field transmission spectrum when a is fixed at 0 degree.

In this paper, a dual-band WiFi antenna and its Multiple Input Multiple Output (MIMO) system application is designed, fabricated, and measured based on the Chinese characters “Men” and “Wei”. The antenna uses a 40×40×1.6 mm3 Fr4 substrate to analyze the combinatorial structure of Chinese characters using the theory of characteristic modes (TCM), to optimize the antenna dimensions by analyzing the mode current distribution, and to broaden the antenna bandwidth by etching rectangular slots on the ground. The measured and simulated results show that the four-element MIMO antenna covers 5.68-8.01 GHz, the isolation between the antennas is higher than 20 dB in the working band, the Envelope Correlation Coefficient (ECC) and the channel capacity losses (CCLs)of the simulation is lower than 0.001 and 0.18 bits/s/HZ, respectively. The efficiency of the antenna is higher than 90%, and it can be used for WiFi communication band (5.8 GHz and 6 GHz).

Background: In recent years, the assessment and guidance of cardiopulmonary resuscitation (CPR) quality using noninvasive and invasive monitoring techniques have been increasingly recommended. In this study, we introduce a new physiological monitoring system that simultaneously measures arterial pressure (AP), venous pressure (VP), and cerebral tissue oxygen saturation (SctO2) during CPR. Methods: This prospective observational study was conducted at a single center (Kagoshima City Hospital). Adult out-of-hospital patients aged ≥18 years with an intravenous femoral arterial line, venous line, and SctO2 monitor were included. We measured femoral arterial pressure (FAP) and femoral venous pressure (FVP) invasively if catheters were immediately inserted into the femoral artery and vein for potential candidates who require interventions such as extracorporeal cardiopulmonary resuscitation but did not receive such interventions as a result. Results: We observed several representative cases that provided the following insights: We presented several cases, including two patients with significant increases in FVP and low SctO2 values, and in both cases, return of spontaneous circulation (ROSC) was not achieved. In contrast, we also presented two cases in which CPR resulted in higher FAP compared to FVP and an upward trend in SctO2 values was observed, and both instances achieved ROSC. Conclusion: We presented a simultaneous physiological monitoring system that can monitor AP, VP, and SctO2 during CPR. Further case accumulations will be necessary to assess the variations in hemodynamic status during CPR and the association between each hemodynamic status and outcomes after cardiac arrest.

Based on the 2013–2017 Chinese Family Database and China Household Finance Survey, the study examines the impact of farmland transfer on the income structure of agricultural households. We observe a significant rise in the income of transferred-out households, while that of transferred-in households is unchanged. A further empirical decomposition of income shows a significant increase in both the wage and asset generated incomes of transferred-out households. Although the income generated by transferred-in households through agricultural production and management increases significantly, the decrease in wage income is larger. The study’s empirical designs are robustly tested with propensity score matching and instrumental variables. Moreover, we conduct a comparative analysis of the external constraints faced by the two groups to explore the reasons for the divergence of the income effect. The results show that transferred-in households face highly pronounced external constraints in terms of capital, technology, and farmland size, while transferred-out households face relatively fewer impediments to non-agricultural employment. Our empirical results imply that external constraints can limit the social welfare improvements of agricultural land reform, suggesting that other complementary measures would be required for future policy improvements to work better.

The implementation of One Health/EcoHealth/Planetary Health approaches has been identified as key (i) to address the strong interconnections between risk for pandemics, climate change and biodiversity loss, and (ii) to develop and implement solutions to these interlinked crises. As a response to the multiple calls of scientists in that direction, we have put forward seven long term research questions regarding COVID-19 and emerging infectious diseases (EIDs) that are based on an effective integration of environmental, ecological, evolutionary, and social sciences to better anticipate and mitigate EIDs. Research needs cover the social-ecology of infectious disease agents, their evolution, the determinants of susceptibility of humans and animals to infections, and the human and ecological factors accelerating infectious disease emergence. For comprehensive investigation, they include the development of nature-based solutions to interlinked global planetary crises, addressing ethical and philosophical questions regarding the relationship of humans to nature and regarding transformative changes to safeguard the environment and human health. In support of this research, we propose the implementation of innovative multidisciplinary facilities embedded in social-ecosystems locally: the “ecological health observatories” and the “living laboratories”. This work has been carried out in the frame of the EC project HERA (www.HERAresearchEU.eu) that aims to set the priorities for an environment, climate and health research agenda in the EU by adopting a systemic approach in the face of global environmental change.

During the night between 9 and 10 September 2017, multiple flash floods associated to a heavy-precipitation event affected the town of Livorno, located in Tuscany, Italy. Accumulated precipitation exceeding 200 mm in two hours, associated with a return period higher than 200 years, caused all the largest streams of the Livorno municipality to flood several areas of the town. We used the limited-area Weather Research and Forecasting (WRF) model, in a convection-permitting setup, to reconstruct the extreme event leading to the flash floods. We evaluated possible forecasting improvements emerging from the assimilation of local ground stations and X- and S-band radar data into the WRF, using the configuration operational at the meteorological center of Tuscany region (LaMMA) at the time of the event. Simulations were verified against weather station observations, through an innovative method aimed at disentangling the positioning and intensity errors of precipitation forecasts. By providing more accurate descriptions of the low-level flow and a better assessment of the atmospheric water vapour, the results demonstrate that assimilating radar data improved the quantitative precipitation forecasts.

The availability of high quality surface observations of precipitation and volume observations by polarimetric operational radars make it possible to constrain, evaluate and validate numerical models with a wide variety of microphysical schemes. In this article, a novel particle-based Monte-Carlo microphysical model (called “McSnow”) is used to simulate the outer rain bands of Hurricane Dorian which traversed the densely instrumented precipitation research facility operated by NASA at Wallops Island, Virginia. The rain bands showed steady stratiform vertical profiles with radar signature of dendritic growth layers near −15 °C and peak reflectivity in the bright band of 55 dBZ along with polarimetric signatures of wet snow with sizes inferred to exceed 15 mm. A 2D-video disdrometer measured frequent occurrences of large drops &gt;5 mm and combined with an optical array probe the drop size distribution was well-documented in spite of uncertainty for drops &lt;0.5 mm due to high wind gusts and turbulence. The 1D McSnow control run and four numerical “experiments” were conducted and compared with observations. One of the main findings is that even at the moderate rain rate of 10 mm/h collisional breakup is essential for the shape of the drop size distribution.

Ocean surface currents and winds are tightly coupled essential climate variables, and, given their short time scales, observing them at the same time and resolution is of great interest. DopplerScatt is an airborne Ka-band scatterometer that has been developed under NASA's Instrument Incubator Program (IIP) to provide a proof of concept of the feasability of measuring these variables using pencil-beam scanning Doppler scatterometry. In the first half of this paper, we present the Doppler scatterometer measurement and processing principles, paying particular attention to deriving a complete measurement error budget. Although Doppler radars have been used for the estimation of surface currents, pencil-beam Doppler Scatterometry offers challenges and opportunities that require separate treatment. The calibration of the Doppler measurement to remove platform and instrument biases has been a traditional challenge for Doppler systems, and we introduce several new techniques to mitigate these errors when conical scanning is used. The use of Ka-band for airborne Doppler scatterometry measurements is also new, and, in the second half of the paper, we examine the phenomenology of the mapping from radar cross section and radial velocity measurements to winds and surface currents. To this end, we present new Ka-band Geophysical Model Functions (GMF's) for winds and surface currents obtained from multiple airborne campaigns. We find that the wind Ka-band GMF exhibits similar dependence to wind speed as that for Ku-band scatterometers, such as QuikSCAT, albeit with much greater upwind-crosswind modulation. The surface current GMF at Ka-band is significantly different from that at C-band, and, above 4.5 m/s has a weak dependence on wind speed, although still dependent on wind direction. We examine the effects of Bragg-wave modulation by long waves through a Modululation Transfer Function (MTF), and show that the observed surface current dependence on winds is consistent with past Ka-band MTF observations. Finally, we provide a preliminary validation of our geophysical retrievals, which will be expanded in subsequent publications. Our results indicate that Ka-band Doppler scatterometry could be a feasible method for wide-swath simultaneous measurements of winds and currents from space.

This study investigates the impact of narrow-band terahertz pulses on the ferroelectric order parameter in Ba0.8Sr0.2TiO3 films on various substrates. The 375 nm thick BST film on an MgO (001) substrate exhibits enhanced THz-induced second harmonic generation when excited by THz pulses with a central frequency of 1.6 THz, due to the resonant excitation of the soft phonon mode. Conversely, the BST film on a Si (001) substrate shows no enhancement, due to its polycrystalline state. The 800 nm thick BST film on an MgO (111) substrate demonstrates maximum of second harmonic generation signal when excited by THz pulses at 1.8 THz, that is also very close to it`s soft mode frequency (1.9 THz). Notably, the frequency spectrum of the BST/MgO (111) film reveals peaks at both the fundamental and doubled frequencies, highlighting the quadratic dependence of SHG intensity on the THz pulse's electric field strength.

In this paper, we investigate the use of fat tissue as a communication channel between in-body, implanted devices at R-band frequencies (1.7–2.6 GHz). The proposed fat channel is based on an anatomical model of the human body. We propose a novel probe that is optimized to efficiently radiate the R-band frequencies into the fat tissue. We use our probe to evaluate the path loss of the fat channel by studying the channel transmission coefficient over the R-band frequencies. We conduct extensive simulation studies and validate our results by experimentation on phantom and ex-vivo porcine tissue, with good agreement between simulations and experiments. We demonstrate a performance comparison between the fat channel and similar waveguide structures. Our characterization of the fat channel reveals propagation path loss of 1.4 dB and 3.8 dB per 20 mm for phantom and ex-vivo porcine tissue, respectively. These results demonstrate that fat tissue can be used as a communication channel for high data rate intra-body networks.

This paper presents the development of a new system designed to measure the local temperature field in adiabatic shear band. Transient temperature field are simultaneously recorded by an array of 32 InSb infrared (IR) detectors and a streak camera working in visible-near infrared (VIS-NIR). Observations in IR offer a low temperature detection limit (350°C) but they are highly sensitive to uncertainty in the emissivity. Observations in VIS-NIR allow for measurement only at high temperatures (750°C) but they are less affected by uncertainty on emissivity and present a higher temperature sensitivity. By performing simultaneous measurements, it is possible to obtain data on a large temperature range with an improved accuracy at high temperature. The different sources of errors caused by uncertainty in the emissivity, spatial and temporal resolution of the detectors has been analyzed and an estimation of the total measurement uncertainty of the system is given.

Irrigation is one of key agricultural management practices of crop cultivation in the world. Irrigation practice is traceable on satellite image. Most irrigated area mapping methods were developed based on time series of NDVI or back scatter coefficient within the growing season. However, it found the winter irrigation out of growing season is also dominating in north China. This kind of irrigation aims to increase the soil moisture for coping with spring drought, and also reduce the wind erosion with the wet soil in the field surface as the strong wind happens in spring. This study developed a remote sensing-based classification approach to identify irrigated fields with Radom Forest algorithm out of growing season. The results showed that the mean of the highest accuracies of 7 RF models was 94.9% and the mean of the averaged accuracies of 7 RF models was 94.1%; the overall accuracy for all 7 outputs was in the range of 86.8-92.5%, Kappa in the range of 84.0-91.0% and F-1 score in the range of 82.1-90.1%. These results showed that the classification was acceptable and not over performed as the accuracies of all classified images were lower than the models. This study also found that irrigation started to apply in early November and irrigated fields were increased and suspended in December and January due to freeze. The newly irrigated fields were found again in March and April when the temperature goes up above zero degree. The area of irrigated fields in the study area were increasing over time with sizes of 98.6, 166.9, 208.0, 292.8, 538.0, 623.1, 653.8 km2 from December to April, accounting for 6.1%, 10.4%, 12.9%, 18.2%, 33.4%, 38.7%, and 40.6% of the total irrigatable land in the study area, respectively.

In this work, we focus on investigating electrothermal flow in a rotating electric field (ROT-ETF), with primary attention paid to the horizontal traveling-wave electrothermal (TWET) vortex induced at the center of the electric field. The frequency-dependent flow profiles in the microdevice are analyzed using different heat transfer models. Accordingly, we address in particular the importance of electrode cooling in ROT-ETF as metal electrodes of high thermal conductivity while substrate material of low heat dissipation capability are employed to develop such microfluidic chips. Under this circumstance, cooling of electrode array due to external natural convection on millimeter-scale electrode pads for external wire connection occurs and makes the internal temperature maxima shift from the electrode plane to a bit of distance right above the cross-shaped interelectrode gaps, giving rise to reversal of flow rotation from a typical repulsion-type to attraction-type induction vortex, which is in good accordance with our experimental observations of co-field TWET streaming at frequencies on the order of reciprocal charge relaxation time of the bulk fluid. These results point out a way to make a correct interpretation of out-of-phase electrothermal streaming behavior, which holds great potential for handing high-conductivity analytes in modern microfluidic systems.

This study examines the relationship of fear of missing out (FOMO) with heavy social networking among Turkish university students (aged 17 - 55). The perception of the possible role of parental supervision on online activities is also investigated. Factor analysis of FOMO scale led us to evaluate the construct under two dimensions as (1) fear of missing experience and (2) fear of missing activity. The results revealed that fear of missing activity increases social media intrusion while fear of missing experience is found to have no significant effect. The reverse relationship is also valid: an urge to use social media predicts fear of missing out (activity and experience). Fear of missing experience is associated with problematic social media use (PSMU) and a high desire to use social media. The results additionally demonstrate that students aged 30 and older believe more in the requirement of parental control than those aged 17-22.

We report a novel dual-band barrier infrared detector (DBIRD) design using type-II superlattices (T2SLs). The DBIRD structure consists of back-to-back barrier diodes: a "blue channel" (BC) diode which has an nBp architecture, an n-type layer of larger bandgap for absorbing blue band infrared/barrier/p-type layer, and a "red channel" (RC) diode which has an pBn architecture, a p-type layer of smaller bandgap for absorbing red band infrared/barrier/n-type layer. Each has a unipolar barrier using a T2SL lattice matched to a GaSb substrate to impede the flow of majority carriers from the absorbing layer. Each channel in the DBIRD can be independently accessed with a low bias voltage, as is preferable for high-speed thermal imaging. Device modeling of DBIRDs and simulation results of the current-voltage characteristics under dark and illuminated conditions are also presented. They predict that dual-band operation of the DBIRD will produce low dark currents and 27-33% quantum efficiencies for the in-band photons in the BC with λc=5.58 μm, and a nearly-constant 33% in the RC with λc=8.05 μm. The spectral quantum efficiency of the BC for 500 K blackbody radiation is approximately 20% over the range of λ=3 − 4.2 μm, while that of the RC has a peak of 42% at 5.7 μm. The DBIRD may provide improved high-speed dual-band imaging in comparison with NBn dual-band detectors.

The report introduces hybrid polyelectrolyte-stabilized colloids combining blue and green emitting building blocks, that are citrate carbon dots (CDs) and [TbL]+ chelate complexes with 1,3-diketonate derivatives of calix[4]arene. The joint incorporation of green and blue emitting blocks into the polysodium polystyrenesulfonate (PSS) aggregates is carried out through the solvent-exchange synthetic technique. The coordinative binding between Tb3+ centers and CD surface groups in initial DMF solutions both facilitates joint incorporation of [TbL]+ complexes and the CDs into the PSS-based nanobeads and affects fluorescence properties of [TbL]+ complexes and CDs, as well as their ability to temperature sensing. The variation of the synthetic conditions is represented herein as a tool for tuning the fluorescent response of the blue and green emitting blocks upon heating and cooling. The revealed regularities enable developing either dual band luminescent colloids for monitoring temperature changes within 25-50 C through double color emission, or to transform the colloids into ratiometric temperature sensors via simple concentration variation of [TbL]+ and CDs in initial DMF solution. Novel hybrid carbon dots-terbium chelate PSS-based nanoplatform opens an avenue for new generation of sensitive and customizable single excited dual band nanothermometers.

The next generation of wireless and mobile networks will have to handle a significant increase in traffic load compared to the actual one. This situation calls for novel ways to increase spectral efficiency. Therefore in this paper, we propose a wireless spectrum hypervisor architecture that abstracts a radio frequency (RF) front-end into a configurable number of virtual RF front-ends. The proposed architecture has the ability to enable flexible spectrum access in existing wireless and mobile networks, which is a challenging task due to the limited spectrum programmability, $i.e.$, the capability a system has to change the spectral properties of a given signal to fit an arbitrary frequency allocation. The main goal of the proposed approach is to improve spectral efficiency by efficiently using vacant gaps in congested spectrum-bandwidths or adopting network densification through infrastructure sharing. We demonstrate mathematically how our proposed approach works and present several simulation results proving its functionality and efficiency. Additionally, we designed and implemented an open-source and free proof of concept prototype of the proposed architecture, which can be used by researchers and developers to run experiments or extend the concept to other applications. We present several experimental results used to validate the proposed prototype. We demonstrate that the prototype can easily handle up to 12 concurrent physical layers.

Substrate integrated waveguides reduce the losses and increase the quality factor of resonators in communication filters when compared with traditional planar technologies, while maintaining their low cost and low profile characteristics. Empty substrate integrated waveguides go one step further, removing the dielectric of the substrate. One of these transmission lines is the empty substrate integrated coaxial line (ESICL), which adds the advantage of being a two conductor structure. Thus, it propagates a TEM mode, which reduces the dispersion and the bandwith limitation of other one conductor empty substrate integrated waveguides. Continuous profile filters, at the cost of being long structures, are very easy to manufacture and design (usually no optimization is needed), and they are highly insensitive to manufacturing tolerances. In this work a simple continuous profile filter, with a stop band response, is designed for the first time in the novel ESICL technology. The influence of the design parameters on the insertion losses and fractional bandwidth is discussed. A prototype has been successfully manufactured and measured. A sensitivity analysis shows the high tolerance of the proposed stop band filter to manufacturing errors.