This work presents the results regarding the synthesis of tungsten nanoparticles (W NPs) by magnetron sputtering combined with gas aggregation (MSGA) when H2 mixed with Ar is used as working gas, the amount of H2 being increased up to 82%. The results show that up to 40% H2 in discharge the synthesis rate increases over 60 times, rapidly decreasing for over 50% H2 in discharge. The W dust is still produced in H2 dominated discharge (82%), the deposition rate being small but not negligible (20 mg/hour). The obtained WNPs are isolated, with the diameter decreasing from 50 nm to 15 nm when the amount of H2 in discharge is smaller than 41%. Over this value, the particles tend to agglomerate, forming structures similar to film-like deposits. Also, the diameter of the deposited spots on substrates is dependent on the H2 content in discharge. This allows the efficient coating of substrates with dimensions up to 26 mm by translating them in front of the MSGA cluster source exit aperture. Supplementary, for 41% H2 in discharge, the influence of synthetic air leaks (0-5%) in discharge was investigated. The deposition rate decreases rapidly (ceasing for around 4% air in discharge) and the obtained nanoparticles tend to agglomerate (at 2% air content, the dust deposit has the aspect of a near continuous film). Chemical composition investigations show a pronounced tendency of oxidation, nitridation and oxynitride formation in the presence of air leaks.

We investigate solutions of the classical Mathieu-Hill (MH) equation which characterizes the dynamics of trapped ions, based on the Floquet theory and starting from a well known analytical model. The analytical model we introduce demonstrates that the equations of motion are equivalent to those of the harmonic oscillator (HO). Two independent approaches are used, based on two classes of complex solutions of the MH equation. The paper addresses both the damped HO and parametric oscillator (PO) for an ion confined in an electrodynamic (Paul) trap. Stability and instability regions for the periodic orbits associated to the MH equation which describes a HO (PO) confined in an electrodynamic trap are also discussed, depending on the values of the Floquet exponent, for very small values of the $q$ parameter. The main objective of the paper is to identify stable and bounded solutions for the dynamics of a HO levitated in an electrodynamic trap. This paper represents a follow-up of a recently published article in Photonics, 11 (6) 551.

The stability properties of the Hill equation are discussed, and especially those of the Mathieu equation that characterize ion motion in electrodynamic traps. The solutions of the Mathieu equation for a trapped ion are characterized by using the Floquet theory and Hill's Method solution, which yields an infinite system of linear and homogeneous equations whose coefficients are recursively determined. Stability is discussed for parameters $a$ and $q$ that are real. Characteristic curves are introduced naturally by the Sturm-Liouville problem for the well known even and odd Mathieu equations $ce_m(z,q)$ and $se_m(z,q)$. We illustrate the stability diagram for a combined (Paul and Penning) trap and represent the frontiers of the stability domains for axial and radial motion. In case of a Paul trap the stable solution corresponds to a superposition of harmonic motions. The problem of evaluating the maximum amplitudes of stable oscillations for the ideal conditions (taken into consideration) is also approached. Anharmonic corrections are discussed within the frame of the perturbation theory, while the frontiers of the modified stability domains are determined as a function of the chosen perturbation parameter. The results apply to 2D and 3D ion traps used for different applications in quantum engineering, among which optical clocks, quantum logic and quantum metrology, but not restricted only to these.

A new two-step method for developing a nanocomposite of polypropylene (PP) decorated with photocatalytically active TiO2 nanoparticles (nTiO2) is proposed. This method involves low-temperature plasma functionalization of polypropylene followed by ultrasound-assisted anchoring of nTiO2. The nanoparticles, polymeric substrate, and resultant nanocomposite were thoroughly characterized using nanoparticle tracking analysis (NTA), microscopic observations (SEM, TEM, EDX), spectroscopic investigations (XPS, FTIR), thermogravimetric analysis (TG/DTA), and water contact angle (WCA) measurements. The photocatalytic activity of the nanocomposites was evaluated through the degradation of methyl orange. The individual TiO2 nanoparticles ranged from 2-6 nm in size. Oxygen plasma treatment of PP generated surface functional groups (mainly -OH and -C=O), transforming the surface from hydrophobic to hydrophilic, which facilitated efficient deposition of nTiO2. Optimized plasma treatment and sonochemical deposition parameters resulted in an active photocatalytic nTiO2/PP system, degrading 80% of methyl orange under UVA irradiation in 200 minutes. The proposed approach is considered versatile for the functionalization of polymeric materials with photoactive nanoparticles and, in a broader perspective, can be utilized for the fabrication of self-cleaning surfaces.

The surface characterization of indium tin oxide (ITO) films was processed by oxygen (O2) plasma gas using a magnetron sputtering method of varying O2-plasma gas from 20 sccm to 100 sccm for potentially fostering in electronic devices applications on dye-sensitize solar cells (DSSC) in this work. In order to gain an outstanding performance rate with high-quality thin films, the affect of correlation between the electrical, optical, and morphology properties was significantly investigated. Clearly, the content of investigation exhibited that the films properties was changed by variation of the gas composition. These changes have contemporary relevance to the sputtering gas during the deposition process. To conclude, the greatest electrical properties was displayed by O2 -plasma gas flow rate of 20 sccm, which showed the lowest resistivity. In addition to this, the final products were practically fabricated to active layers for dye-sensitize solar cells (DSSC) applications. The highest efficiency of DSSC device was indicated of approximately 0.35% which was located by 40 sccm of the O2-plasma gas. Consequently, the study could be a possibility way of preparing ITO thin films with improved special properties of substantial applications for solar cells devices in the near future.

DSSC devices are among the most widely studied thin-film solar cells because of their cost-effectiveness, low toxicity, and simple fabrication method. However, there is still much scope for replacing current DSSC materials due to their high cost, low volume, and lack of long-term stability. Accordingly, ITO-nanorod films were fabricated by E-beam evaporation using the glancing angle deposition method in this study. Then, the ITO-nanorod was treated by oxygen plasma via a bias-magnetron RF sputtering process to improve the efficiency of DSSC under a varying gas flow rate of 20, 40, 60, 80, and 100 sccm. The FE-SEM investigation of the ITO film structure revealed that the obtained nanorod structures have slightly different diameters. At the same time, an increase in the oxygen flow rate resulted in a rougher film surface structure. In this, the lower sheet resistance was received because of rougher morphology. When comparing the DSSC efficiency test results, we found that at a gas flow rate of 100 sccm, the highest efficiency value showed by 9.5%. On the other hand, the ITO-nanorod without plasma treatment exhibited the lowest efficiency. Hence, plasma technology can be practically applied to improve the efficiency of DSSC devices. This study will be a prototype of a highly advanced solar cell manufacturing method for the solar cell industry.

In the presented work, on the example of thin-walled specimens made by selective laser melting technology from AlSi10Mg subjected to preliminary heat treatment, it is shown that there is a critical point of transition from the elastic-plastic region of the engineering stress-strain diagram to the yield and fracture stresses. It was found that the critical point has a strong statistically significant correlation (0.83 by Spearman and 0.93 by Pearson) with the strain hardening coeffi-cient calculated in the section from yield strength to fracture strength. A regression equation linking the critical transition point to the strain hardening coefficient was obtained. It is shown that with increasing plasticity of thin-walled samples obtained by selective laser melting of AlSi10Mg leads to a change in the type of stress distribution in the elastic-plastic region (the Weibull distribution changes to a normal distribution) and the contribution of the probability density of stress distribution described by the Cauchy distribution with a mode near the fracture stress to the full probability density of fracture increases.

Gene expression variations of plant leaf are investigated by irradiating seed and leaf with oxygen or air plasmas. Enhancement of leaf growth is induced by oxygen plasma irradiation on seeds, which is supported by increased gene expression for protein synthesis, oxidative-reduction reactions and decreased gene expression concerning DNA methylation and histone modification. Suppression of leaf growth is observed by the oxygen plasma, which would be owing to increased gene expression concerning heat shock protein and redox reaction, and decreased expression of photosynthesis and glycoprotein. Also, gene expression variation due to air plasma irradiation is almost same as that of oxygen plasma. Active oxygen species are major factors in both oxygen and air plasmas for the variation of gene expressions in plant.

To discover potential micro(mi)RNAs biomarkers of SARS-CoV-2 infection and disease progression, large-scale deep sequencing analysis of small RNA expression was performed on plasma samples from 40 patients hospitalized for SARS-CoV-2 infection (median 13.50 [IQR 9–24] days since symptoms initiation) and 21 healthy noninfected individuals. A totally of 1218 different miRNAs were identified. When compared with healthy noninfected donors, SARS-CoV-2 infected patients showed significantly (fold change [FC] >1.2 and adjusted p [padj] <0.05) altered expression of 190 miRNAs. The top 10 differentially expressed (DE) miRNAs were miR-122-5p, let-7b-5p, miR-146a-5p, miR-342-3p, miR-146b-5p, miR-629-5p, miR-24-3p, miR-12136, let-7a-5p, and miR-191-5p, which displayed FC and padj values ranging from 153 to 5 and 2.51 × 10-32 to 2.21 × 10-21, respectively, which unequivocally diagnosed SARS-CoV-2 infection. No differences in blood cell counts and biochemical plasma parameters, including interleukin 6, ferritin and D-dimer, were observed between COVID-19 patients on high-flow oxygen therapy, low-flow oxygen therapy, or not requiring oxygen therapy. Notably, 31 significantly deregulated miRNAs were found when patients on high- and low-flow oxygen therapy were compared. SARS-CoV-2 infection generates a specific miRNA signature in hospitalized patients. Specific miRNA profiles are associated with COVID-19 prognosis in patients requiring oxygen flow.

This study aimed to evaluate the effects of plasma treated metal contaminated water, used for irrigation, on plant growth. Zinc (Zn) is one of the more commonly used metals. It can enter the environment from industrial processes as particles released into the atmosphere or as wastewater discharged into waterways or the ground. Exposure to large amounts of zinc, even for a short time, can seriously affect human health. In this experiment, three different DBD O2 plasma treated zinc contaminated water and a control (tap water) were used, with Arabidopsis thaliana as the model plant. The treatments were: i) Control, ii) Zn water, iii) Zn+O3(30 min), and iv) Zn+O3(60 min). Arabidopsis plant exhibited maximum growth in the Zn+O3(30 min) treatment. All growth parameters, except leaf area, followed this trend: Zn+O3(30 min) > Control > Zn water > Zn+O3(60 min). Gene expression analysis revealed that reduced metal ion stress and controlled oxidation due to active oxygen species contributed to favorable/improved growth of Arabidopsis in the Zn+O3(30 min) treatment. Therefore, 30 minutes of DBD O2 plasma treated zinc contaminated water [Zn+O3(30 min)] can mitigate the adverse effects of excess zinc ions and promote the growth of Arabidopsis plants.

Screen-printed carbon electrode (SPCE) is a useful technique that has been widely used in the practical application of biosensors oriented to point-of-care testing (POCT) due to its characteristics of cost-effectiveness, disposability, miniaturization, wide potential window, and easy of electrode design. Compared with gold or platinum electrodes, surface modification is difficult because the carbon surface is chemically or physically stable. Oxygen plasma can easily produce carboxyl groups on the carbon surface, which act as scaffolds for covalent bonds. However, the effect of O2-plasma treatment on electrode performance remains to be investigated from an electrochemical perspective, and sensor performance can be improved by clarifying the surface conditions of plasma treated biosensors. In this research, we compared antibody modification by plasma treated and physical adsorption, using our original immunosensor based on gold nanoparticles (AuNPs). Consequently, the O2-plasma treatment produced carboxyl groups on the electrode surface, which changed the electrochemical properties owing to electrostatic interactions. It was also found that the surface became hydrophilic, inhibiting non-specific antigen adsorption. The sensitivity was 6.5 times higher than the Limit of Detection (LOD) using physical adsorption.

Cell-based therapies and tissue engineering applications require biocompatible substrates that support and regulate the growth, survival, and differentiation of specific cell types. Extensive research efforts in regenerative medicine are devoted to the development of tunable biomaterials which support various cell types including stem cells. In this research, the non-cytotoxic biopolymer polycaprolactone (PCL) was fabricated into 2D and 3D scaffolds with or without the low-pressure oxygen plasma treatment to enhance hydrophilicity. Cellular responses and biocompatibility were evaluated using a human Wharton’s jelly mesenchymal stem cell line (BCP-K1). The 2D PCL scaffolds enhanced initial cell attachment compared to the 3Ds indicated by a higher expression of focal adhesion kinase (FAK). Whilst, the 3D scaffolds promoted cell proliferation and migration as evidenced by higher cyclin A expression and filopodial protrusion, respectively. The 3D scaffolds potentially protected the cell entering to apoptosis/necrosis program and induced cell differentiation, evaluated by gene expression. Both 2D and 3D PCL appeared to have stronger effects on cell behavior than a control substrate (polystyrene). In summarize, the different configuration and surface properties of PCL scaffolds provide various options for modulation of stem cell behaviors, including attachment, proliferation, survival, and differentiation, when combined with specific growth factors and culture conditions.

The radiative heat transfer in arc plasma models is considered from the point of view of its description in terms of a net emission coefficient, the method of spherical harmonics in its lowest order, and the discrete ordinate method. Net emission coefficients are computed applying approximate and numerical approaches, the multi-band representation of the spectral absorption coefficient with three kinds of its averaging and two datasets. The self-consistent access to the radiative heat transfer is applied to a two-dimensional axisymmetric model of free-burning arc in argon at atmospheric pressure. The results obtained from the models employing the net emission coefficient, the method of spherical harmonics, and the discrete ordinate method are compared.

Oxidative stress has been implicated in cellular senescence and aging, as well as in the onset and progression of many diverse genetic and acquired diseases and conditions. The search for biomarkers of oxidative stress has become relevant to many biomedical fields using many different methods and approaches. Fluorescence methodology is advantageous because of its simplicity and high sensitivity. Fluorescent probes are frequently used to investigate the role of reactive oxygen species in oxidative stress in experimental or clinical settings, often involving the use of flow cytometry and related single-cell based technologies. To assess the specific role of reactive oxygen species in oxidative stress studies by cytometric methodologies, it is essential to detect and characterize these species accurately. However, the detection and quantitation of individual intracellular ROS is still a challenge, but different and complementary strategies may focus on other endpoints of oxidative stress. In this review we present and discuss briefly the limitations and perspectives of such approaches. Based on our results, we also provide recommendations for proper design of cytometric studies of oxidative stress in order to prevent or minimize experimental errors..

A comprehensive study of the interactions of human serum albumin (HSA) and α-1-acid glycoprotein (AAG) with two isoquinoline alkaloids: allocryptopine (ACP) and protopine (PP) was performed. The UV-Vis spectroscopy, molecular docking, competitive binding assays, and circular dichroism (CD) spectroscopy were used for the investigations. The results showed that ACP and PP form spontaneous and stable complexes with HSA and AAG, with ACP displaying a stronger affinity towards both proteins. Molecular docking studies showed also revealed the preferential binding of ACP and PP to specific sites within HSA, with site 2 (IIIA) being identified as the favored location for both alkaloids. This was supported by competitive binding assays using markers specific to HSA's drug binding sites. Similarly, for AAG, a decrease in fluorescence intensity upon addition of the alkaloids to AAG/ Quinaldine Red (QR) complexes indicated the replacement of the marker by the alkaloids, with ACP showing a greater extent of replacement than PP. CD spectroscopy showed that the proteins’ structures remained largely unchanged suggesting that the formation of complexes did not significantly perturb the overall spatial configuration of these macromolecules. These findings are crucial for advancing the knowledge on the natural products-protein interactions and the future design of isoquinoline alkaloid-based therapeutics.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Despite the best efforts in air-purification, airborne infectious diseases do and will continue to spread due to continuous emission of bioaerosols by the host/infected person. To tackle the rapid spread of airborne infectious diseases, a shift in focus from air-purification to bioaerosol disinfection/ decontamination is urgently needed. In this work, we studied a cold plasma ionizer (CPI) and electrostatic precipitator (ESP)-coupled CPI (CPI-ESP) for disinfection and cleaning of bioaerosols. Using porcine respiratory coronavirus (PRCV) and E. coli in a testing chamber, we demonstrated that CPI coupled with ESP is an effective technology for inactivating aerosolized microorganisms and microorganisms spread on surfaces. In addition, we have demonstrated the efficiency of a CPI-ESP coupled device for disinfection of naturally occurring airborne microbials in a few indoor settings (i.e., an living room, a discussion room, a schoolroom and an office) to determine the treatment duration- and human activity-dependent efficacy. To understand the disinfection mechanism, we conduced fluorescence microscopy study to reveal different degree of bacteria cell membrane damage under CPI treatment.

Reactive oxygen species (ROS) are produced during cellular metabolism and in response to environmental stress. While low levels of ROS play essential physiological roles, excess ROS can damage cellular components, leading to cell death or transformation. ROS can also regulate protein interactions in cancer cells, thereby affecting processes such as cell growth, migration, and angiogenesis. Dysregulated interactions occur via various mechanisms, including amino acid modifications, conformational changes, and alterations in complex stability. Understanding ROS-mediated changes in protein interactions is crucial for targeted cancer therapies. In this review, we examine the role that ROS mechanisms in regulating pathways through protein-protein interactions.

Magneto-optic (MO) imaging and sensing are at present the most developed practical applications of thin-film MO garnet materials. However, future component and system-level sensors and imagers technology improvements are still necessary in order to improve sensitivity for a range of established and also the forward-looking applications. These improvements are expected to originate from new material system development. We propose a set of technological modifications for the RF-magnetron sputtering deposition and crystallization annealing of magneto-optic bismuth-substituted iron-garnet films and investigate the improved material properties. Results show that standard crystallization annealing for the as-deposited ultrathin (sputtered 10 nm thick, amorphous phase) films resulted in more than a factor of two loss in the magneto-optical activity of the films in visible spectral region, compared to the liquid-phase grown epitaxial films. Results also show that an additional 10 nm-thick metal-oxide (Bi2O3) protective layer above the amorphous film results in ~2.7 times increase in the magneto-optical quality of crystallized iron-garnet films. On the other hand, the effects of post-deposition oxygen (O2) plasma treatment on the magneto-optical (MO) properties of Bismuth substituted iron garnet thin films material is investigated. Results show that, in the visible part of the electromagnetic spectrum (at 532 nm), the O2 treated (up to 3 minutes) garnet films retain higher specific Faraday rotation and figure of merit than those of non-treated garnet films.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

Pregnancy at advanced maternal age (AMA) is a condition of potential risk for the development of maternal-fetal complications with possible repercussions even in the long-term. Here, we analyzed the changes of plasma redox balance and the effects of plasma on human umbilical cord mesenchymal cells (hUMSCs) in AMA pregnant women (patients) at various timing of pregnancy. One hundred patients and twenty pregnant women younger than 40 years (controls) were recruited, and evaluated at various timings during pregnancy until after delivery. Plasma samples were used to measure the thiobarbituric acid reactive substances (TBARS), glutathione and nitric oxide (NO). In addition, plasma was used to stimulate the hUMSCs, which were tested for cell viability, reactive oxygen species (ROS) and NO release. The obtained results showed that throughout pregnancy until after delivery in patients the levels of plasma glutathione and NO were lower than those of controls, while those of TBARS were higher. Moreover, plasma of patients reduced cell viability and NO release, and increased ROS release in hUMSCs. Our results highlighted alterations in the redox balance and the presence of potentially harmful circulating factors in plasma of patients They could have clinical relevance for the prevention of complications related to AMA pregnancy.

A detailed review of the scientific literature was undertaken to examine the most recent developments in plasma processing in the field of medicine. The first part of the review includes a detailed breakdown of the different types of coatings that can be applied onto medical devices using plasma, with a specific focus on antimicrobial surfaces. The developments during 2023 in plasma deposited biocompatible, drug delivery and adhesive coatings are described and specific applications in additive manufacturing are highlighted. The use of plasma and plasma activated liquids as standalone therapeutics continues to evolve and pertinent advances in this field are described. In addition, the combination of plasma medicine with conventional pharmaceutical interventions was reviewed and key emerging trends were highlighted, including the use of plasma to enhance drug delivery directly into tissue. The potential synergies between plasma medicine and chemotherapeutics for oncology and infection treatment is a growing area and recent advancements are noted. Finally, the use of plasma to control excess antibiotics and to intentionally degrade such materials in waste streams is described.

The wastewater problem is becoming an increasingly significant environmental issue affecting various aspects of human activities. The generation of reactive oxygen species (ROS) in water through certain physicochemical processes, which can oxidize or degrade various organic and chemical compounds, offers an effective purification method. The main advantage of these methods is the elimination of chemical reagents. Aim of this work is to investigate the possibility of regulating the ROS content in water by altering the characteristics of the plasma discharge that occurs under hydrodynamic cavitation in the water flow. ROS concentration was determined using the permanganate oxidation titration technique. It was found that the content of various reactive oxygen species in water after treatment can be controlled by varying the power of the electrical pulses applied. Additionally, the study obtained the dependence of ROS concentration in treated water samples on storage time, indicating a prolonged effect of sonoplasma treatment on the antibacterial properties of water. Analysis of water samples using a biological test culture of Salmonella typhimurium revealed bacteriostatic properties of the water for at least 48 hours after sonoplasma discharge treatment.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Background: Portable oxygen concentrators (POCs) have shown efficacy in delivering adequate oxygen for various patient scenarios; however, there is a lack of research on POCs’ efficacy across different respiratory rates specifically among COPD patients. Methods: This bench study was conducted using the IngMar Medical Active Servo Lung 5000 attached to flexible tubing, which simulated an adult patient’s nares. An oxygen analyzer (Maxtec Handi+) was connected to the tubing 6 inches below the nares to estimate the inspired oxygen concentration at the adult trachea. A standard nasal cannula was placed in the simulated patient nares, which was also attached to each POC. The IngMar Lung was programmed to simulate a COPD patient at the following respiratory rates: 15, 20, 30, and 40 breaths/min. POC devices were then compared to an oxygen wall outlet and a standard oxygen concentrator (non-portable CAIRE device). The POCs included the CAIRE FreeStyle Comfort (with Autosat), CAIRE FreeStyle Comfort (without Autosat), Inogen G4, Inogen G5, Phillips SimplyGo Mini, GCE Zen-O lite, Drive Medical iGo2, and Kingon POCs. Descriptive statistics and ANOVAs were computed to determine statistically significant differences between POCS and control devices (wall oxygen and standalone oxygen concentrator). Results: Across most respiratory rate scenarios, the wall oxygen and standalone oxygen concentrator (control group) resulted higher oxygen measurements compared to the POCs. Among the POCs on setting 2, the highest oxygen measurement for 15, 30, and 40 breaths/min was the CAIRE FreeStyle Comfort with AutoSat on sensitivity 5 (24.43%, 24.81%, and 25.0%, respectively). On setting 2, the 20 breaths/min highest oxygen measurement was the Inogen G4 (24.43%). For setting 5, the highest oxygen measurement for 15 breaths/min and 40 breaths/min was the CAIRE FreeStyle Comfort without AutoSat (31.56% and 26.13%, respectively), while the highest oxygen measurement for 20 breaths/min was the Inogen G5 (30.26%), and the highest oxygen measurement for 30 breaths/min was the CAIRE FreeStyle Comfort with AutoSat on sensitivity level 5 (27.89%). Conclusions: The oxygen administered through the wall and the standalone CAIRE oxygen concentrator all delivered higher oxygen levels compared to the POCs (with the exception of the 40 breaths/min scenario on setting 2). However, among the POCs, the CAIRE Freestyle Comfort with AutoSat, CAIRE Freestyle Comfort without AutoSat, and the Inogen G4 all performed the best among the various breathing rate scenarios.

The main goal was to investigate the ability of non-thermal plasma reactor with gliding arc discharge to remove the diesel exhaust particulates (DEPs). A conventional knifed-shaped LTP GA reactor was utilized. Three cases were studied: 140 L/min, 70 L/min and 14 L/min of air drawn through the reactor and diesel exhaust fumes were sampled continuously. They were assayed in terms of concentration and number particle size distribution. The higher the residence time’s, the higher the energy input that may be utilized for DEPs’ removal. Reactor’s performance definitely lowered the concentration of DEPs (250 - 580 nm) and altered their number size distribution. There was no effect on the number concentration, nor on the particle size distribution, of DEP particulates of 10 – 250 nm in size. The effectiveness of DEPs’ removal: Decreasing flow rate from 140 L/min to 70 L/min somehow altered the values. Achieving the airflow of 14 L/min led to a substantial improvement (even to a fourfold increase for 300 – 480 nm particles). Non-thermal plasma reactors with gliding arc discharge may be successfully adapted in the process of DEPs’ treatment. Their performance may be optimized by adjusting the airflow at the inlet of reactor to guarantee the longest aerosol residence times and the highest removal efficiency.

This study investigates the optical properties of Yttrium Orthoferrite thin films fabricated via plasma laser deposition. Yttrium Orthoferrite, a ferrimagnetic material known for its potential applications in spintronics and photonics, was deposited on single-crystal substrates under controlled conditions to analyze its optical characteristics. The influence of deposition time, on the film quality and optical properties was examined.

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides were prepared, varying nominal cerium com-positions (x=0, 0.2, 0.3, and 1). The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, rang-ing from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in textural properties of the catalysts was noted, being particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under two contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface ar-ea in loose contact mode. Notably, the T10 and T50 parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511℃ and 538℃ for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed a significant relationship emerges between work function values and the formation of oxy-gen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter which showed better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered.

Rationale: Post-hepatectomy liver failure (PHLF) remains a significant risk for patients undergoing partial hepatectomy (PHx). Reliable prognostic markers and treatments to enhance liver regeneration are lacking. Plasma nanoparticles, including lipoproteins, exosomes, and extracellular vesicles (EVs), can reflect systemic and tissue-wide proteostasis and stress, potentially aiding liver regeneration. However, their role in PHLF is still unknow. Methods: Our study included 9 patients with hepatocellular carcinoma (HCC) undergoing PHx: 3 patients with PHLF, 3 patients undergoing the Associating Liver Partition and Portal vein Ligation for Staged hepatectomy (ALPPS) procedure and three matched controls without complications after PHx. Patient plasma was collected before (PRE), 1 and 5 days (POD1, POD5) after PHx. EVs were isolated by ultracentrifugation and extracted proteins subjected to quantitative mass spectrometry using a super-SILAC mix prepared from primary and cancer cell-lines. Results: We identified 2625 and quantified 2570 proteins in EVs in PHx patients. Among these, 53 proteins were significantly upregulated and 32 were downregulated in patients with PHLF compared to those without PHLF. Furthermore, 110 proteins were upregulated and 78 were downregulated in PHLF compared to patients undergoing ALPPS. The EV-proteomic signature in PHLF indicates significant disruptions in protein translation, proteostasis, intracellular vesicle biogenesis, as well as alterations in proteins involved in extracellular matrix (ECM) remodeling, metabolic and cell cycle pathways, present already before PHx. Conclusion: Longitudinal proteomic analysis of EV´s circulating in human patient plasma undergoing PHx uncovers proteomic signatures associated with PHLF which reflect dying hepatocytes and endothelial cells and are present before PHx already. Our results support EVs as potential biomarkers and therapeutic targets for liver regeneration and failure.

Due to the imbalance between the supply and demand of oxygen, the oxygen system of iron- and steel-making enterprises in China has problems with high oxygen emission and high pressure in the pipelines, resulting in the energy consumption of oxygen production being high. To relieve this problem, using a large-scale iron- and steel-making mill as a case study, the research on demand forecasting and optimal scheduling of the oxygen system was carried out. The ARIMA model and the GABP model are employed to forecast oxygen demand. Based on the forecast results, an optimal scheduling model for the oxygen system was developed to conduct optimal scheduling. The case study shows that based on the oxygen demand forecast and the optimal scheduling, the oxygen emission and the pipeline pressure in the studied iron- and steel-making enterprise can be significantly reduced, thereby achieving considerable energy-saving effects and economic benefits. Specifically, the following conclusions are obtained: (1) For the oxygen demand forecast, the prediction accuracy of the GABP model is better than that of the ARIMA model. The average MAPE of the 12 sets of data of the ARIMA and GABP models are 23.8% and 20.2%, respectively. (2) By comparing the scheduling results and the field data, it is found that after the scheduling, the amount of oxygen emission has decreased by 6.32%, the pipeline pressure has decreased by 0.61%, and the energy consumption of oxygen compression has decreased by 1.6%. Considering both the oxygen emission loss and the energy consumption of oxygen compression, the total power consumption of the oxygen system is reduced by 1.38%, which saves the electricity cost of about 9.03 million RMB per year.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

Soft magnetic composites cores were produced by Spark Plasma Sintering (SPS) from Ni3Fe@ZnFe2O4 and NiFeMo@ZnFe2O4 pseudo-core-shell powders. In the Fe-Ni alloys@ZnFe2O4 pseudo-core-shell composite powders, the core is a large nanocrystalline Permalloy or Supermalloy particle obtained by mechanical alloying, and the shell is a pseudo continuously layer of Zn ferrite particles. The pseudo-core-shell powders have been compacted by SPS at temperatures between 500-700 ºC, with a holding time of 0 minutes. Several techniques were used for the characterisation of the powders and sintered compacts: X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, magnetic hysteresis measurements (DC and AC) and electrical resistivity. The electrical resistivity is stabilised at values of about 7·10-3 Ω·m for sintering temperatures between 600-700 °C and this value is 3 orders of magnitude higher than the electrical resistivity of sintered Fe compacts. The best relative initial permeability was obtained for the Supermalloy/ZnFe2O4 composite compacts sintered at 600 ºC, which decreases linearly for the entire frequency range studied, from around 95 to 50. Up a frequency of 2,000 Hz the power losses are lower than 1.5 W/kg. At the frequency of 10 kHz, the power losses are larger, but they remain at a low level. In the case of Supermalloy/ZnFe2O4 composite compact SPS-ed at 700 °C, the specific power losses are even lower than 5 W/kg. The power losses decomposition proved that intra-particles losses give the main part of the losses.

Carboxymethyl cellulose (CMC) can act as a nonpermeating cryoprotectant, reducing the toxicity of glycerol. The dog spermatozoa were diluted and frozen in freezing extender supplemented with 0 (control), 0.1, 0.25, 0.5, or 0.75 % (w/v) CMC. Post-thaw, the sperm kinematic parameters (CASA), viability (SYBR-14/PI), and acrosome integrity (FITC-PSA) were evaluated. The expression of genes related to apoptosis (BCL2, BAX, and ANAXA), motility (BACTIN), cold shock proteins (YBX3), and ROS (CAT, ROMO1, and SMOX) was evaluated using qPCR. The total motility was higher in the 0.1 % CMC group compared to the other groups (p<0.05). In addition, the expression of the antiapoptotic gene BCL2 was upregulated in 0.1 % CMC group compared to the control, whereas the gene expression of BAX and SMOX exhibited lower levels in 0.1 and 0.25 % CMC groups than the control group (p<0.05). The expression of YBX3 genes was significantly decreased with 0.25 % CMC supplementation. No significant differences were found in viability, acrosome integrity, or the relative expression of ANAXA, BACTIN, CAT, and ROMO1 genes between the groups. In conclusion, the addition of CMC to a freezing extender improved sperm motility and alleviated cryostress by regulating the gene expression of BCL2, BAX, SMOX, and YBX3.

Producing translucent eggs has been found to reduce the quality and safety of the eggs produced., as well as the demand from consumers. However, the intestinal function and the molecular mechanism for the production of translucent eggs remain uncertain. A total of 120 eggs were allocated into two groups, one for the translucent egg group (group T) and one for the normal group (group C), according to the degree of eggshell translucence. Translucent eggs showed thicker eggshell and lower egg yolk color. We also detected the plasma biochemical index, intestinal morphology and structure, enzyme activity, and antioxidant capacity of the hens’ producing translucent eggs and normal eggs. The results showed that the ratio of duodenal villus length to crypt depth, succinate dehydrogenase (SDH) activity, chymotrypsin, total ATPase (T-ATPase), alkaline phosphatase (AKP) and glutathione peroxidase (GSH-Px) activities were decreased in the hens produced translucent eggs (P &lt; 0.05), but malondialdehyde (MDA) content was increased (P &lt; 0.05); jejunal lipase activity, Na+K+-ATPase activity, total antioxidant capacity (T-AOC), GSH-Px activities were decreased (P &lt; 0.05) in group T; ileal amylase and Ca2+Mg2+-ATPase activities were also decreased (P &lt; 0.05) in group T. In addition, we identified a total of 471 differentially expressed genes (DEGs) in duodenal tissue, with 327 up-regulated genes and 144 down-regulated genes (|log2FC| ≥ 1 and P &lt; 0.05). Enrichment analysis showed that the up-regulated genes, such as GSTT1, GSTO2, GSTA3, were mostly enriched in metabolism of xenobiotics by cytochrome P450, drug metabolism-cytochrome P450 and oxidative phosphorylation pathways. The results of our study indicate that plasma lipid metabolism disorder, decreased intestinal antioxidant capacity, and altered intestinal metabolism capabilities may influence the formation of translucent eggs.

Emerging autologous cellular therapies that utilize platelet-rich plasma (PRP) applications have the potential to play adjunctive roles in a variety of regenerative medicine treatment plans. There is a global unmet need for tissue repair strategies to treat musculoskeletal (MSK) and spinal disorders, osteoarthritis (OA), and patients with chronic complex and recalcitrant wounds. PRP therapy is based on the fact that platelet growth factors (PGFs) support the three phases of wound healing and repair cascade (inflammation, proliferation, remodeling). Many different PRP formulations have been evaluated, originating from human, in vitro, and animal studies. However, recommendations from in vitro and animal research often lead to different clinical outcomes because it is difficult to translate non-clinical study outcomes and methodology recommendations to human clinical treatment protocols. In recent years, progress has been made in understanding PRP technology and the concepts for bioformulation, and new research directives and new indications have been suggested. In this review, we will discuss recent developments regarding PRP preparation and composition regarding platelet dosing, leukocyte activities concerning innate and adaptive immunomodulation, serotonin (5-HT) effects and pain killing. Furthermore, we discuss PRP mechanisms related to inflammation and angiogenesis in tissue repair and regenerative processes. Lastly, we will review the effect of certain drugs on PRP activity, and the combination of PRP and rehabilitation protocols.

In order to enhance the efficiency and combined performances of nitriding layer, aluminum-modified plasma nitriding (Al-PN) was developed in this research by adding some FeAl particles around the samples during plasma nitriding (PN) for 42CrMo steel. The results show that the efficiency is dramatically enhanced almost 6 times comparing with traditional PN, with the effective hardening layer increasing from 224 μm to 1246 μm at 520℃/4h. More importantly, the compound layer increased just a little bit from 11.64 μm to 14.32 μm, which remarkably reduces the ratio of the compound layer thickness to effective hardening layer thickness, thus being quite beneficial to decrease the brittleness level, making the brittleness level decreasing from Level 4 to Level 1. Meanwhile, ultra-high surface hardness and excellent wear behaviors are obtained by aluminum-modified plasma nitriding (Al-PN) due to the formation of dispersed strengthening phased of AlN and FexAl in the nitriding layer, with the surface hardness increasing from 755 HV0.025 to 1251 HV0.025, wear rate decreasing from 8.15 x10-5g N-1 m-1 to 4.07 x10-5g N-1 m-1. In other words, comparing with PN, the wear resistance has been almost doubled by Al-PN. Therefore, the research can provide comprehensive insights into the surface characteristics and combined performances of the aluminum-modified plasma nitriding layer.

Background: Early postoperative airway management after laryngo-tracheal surgery is crucial. Acute respiratory failure due to glottis’ oedema may occur, requiring reintubation. This can prolong ventilatory assistance, jeopardizing the anastomosis. To date, only judicious steroid administration and fluid management are available to avoid more invasive procedures. High-Flow-Oxygen-Therapy(HFOT) is a noninvasive O2 support method providing humidification, warmed air, Positive-End-Expiratory-Pressure(AIRVO2). No data exist about HFOT use to prevent early complications after laryngo-tracheal surgery. Methods: Between Sept.2020-Sept.2022, 107 consecutive patients underwent laryngo-tracheal surgery received HFOT(Group A). Data and long-term results were compared with those of 80 patients operated between Sept.2018-Aug.2020(Group B), when HFOT was not available. All patients were operated in a single center. No pre- or post-operative settings changed, except for HFOT introduction. We analyzed and compared the risk for “delayed” reintubation (unexpected reintubation within the first 24-48 hours after extubating/laryngeal mask removal) in the two groups. Results: No patients reported HFOT-related adverse events. Control group(B) presented “delayed” reintubation in 37% (p= 0.027), Intensive Care Unit admission in 67%(p=0.005) and longer hospital stay(p=0.001) compared to HFOT group(A). Minor complications rate was 3% in both group and overall mortality was 0%. Re-stenosis was described in 4.6% of HFOT group, without a statistically significant difference (p=0.7006). Conclusions: Our study is the first to investigate HFOT use in patients undergoing laryngo-tracheal surgery, potentially representing a consistent innovation in the peri-operative management of these patients. With the limit of a retrospective series, we would suggest HFOT use for preventing post-operative reintubation rate, possibly reducing ICU admission and hospital stay.

The injury causes resistance in human gastric cancer (GC). This Adverse Outcome Pathway (AOP) entitled “Increases in cellular reactive oxygen species (ROS) and chronic ROS leading to human treatment-resistant gastric cancer (GC)” consists of molecular initiating event (MIE) as “Increases in cellular ROS” and “Chronic ROS”, followed by series of key events (KEs); “porcupine-induced Wnt secretion and Wnt signaling activation”, “beta-catenin activation”, “epithelial-mesenchymal transition (EMT), and adverse outcome (AO) as “human treatment-resistant GC” in the sequence. ROS has multiple roles in disease such as development and progression of cancer, or apoptotic induction causing anti-tumor effects. In this AOP, we focus on the role of sustained levels of chronic ROS to induce the therapy-resistance in human GC. EMT, which is cellular phenotypic change from epithelial to mesenchymal-like features, demonstrates cancer stem cell (CSC)-like characteristics in human GC. EMT is induced by Wnt/beta-catenin signaling, providing the rationale to have Wnt secretion and beta-catenin activation as KEs in the AOP.

Individual susceptibility to pulmonary oxygen toxicity (PO2tox) is highly variable and currently lacks a reliable biomarker for predicting pulmonary hyperoxic stress. As nitric oxide (NO) is involved in many respiratory system processes and functions, we aimed to determine if expired nitric oxide (FENO) levels can provide an indication of PO2tox susceptibility in humans. Eight U.S. Navy trained divers volunteered as subjects. The hyperoxic exposures consisted of six- and eight-hour hyperbaric chamber dives conducted on consecutive days in which subjects breathed 100% oxygen at 202.65 kPa. Subjects’ individual variability in pulmonary function and FENO was measured twice daily over five days and compared with their post-dive values to assess susceptibility to PO2tox. Only subjects who showed no decrements in pulmonary function following the six-hour exposure conducted the eight-hour dive. FENO decreased by 55% immediately following the six-hour oxygen exposure (n=8, p<0.0001) and by 63% following the eight-hour exposure (n=4, p<0.0001). Four subjects showed significant decreases in pulmonary function immediately following the six-hour exposure. These subjects had the lowest baseline FENO and the lowest post-dive FENO and had clinical symptoms of PO2tox. Individuals with low FENO were the first to develop PO2tox symptoms and deficits in pulmonary function from the hyperoxic exposures. These data suggest that endogenous levels of NO in the lung may protect against the development of PO2tox.

The cornea is an avascular tissue which has attracted much attention by the uniqueness of its anatomical characteristics, it has, in proportion, an enormous size, in relation to the number of vessels, because on average few cells in the organism are away more than 30 microns of a blood vessel. However, the cornea, with a diameter of between 11 and 12 mm, is a unique example. It has been tried to explain the notable absence of blood vessels in the cornea, arguing that corneal tissues are able to take oxygen directly from the air. In this article we are explaining that based on the physicochemical characteristics of molecular oxygen and the cell membrane, cytoplasm, water, and cellular metabolism, it is not possible that epithelial corneal cells directly take oxygen from the air, instead, corneal cells have molecules that can dissociate the water molecules thereby these cells, like any other eukaryotic cells, take the oxygen from the intracell water, like plants.

Oxidation reactions on semiconducting metal oxides (SMOs) surfaces have been extensively worked on in catalysis, fuel cells, and sensors. SMOs engaged powerfully in energy-related applications such as batteries, supercapacitors, solid oxide fuel cells (SOFCs), and chemical gas sensors. The deep understanding of SMO surface and oxygen interactions and defect engineering has become significant because all those mentioned applications are based on the adsorption/absorption and consumption/transportation of adsorbed (physisorbed-chemisorbed) oxygen. More understanding of adsorbed oxygen and oxygen vacancies (〖V_O^•,V〗_O^(••)) is needed, as the former is the vital requirement for sensing chemical reactions, while the latter facilitates the replenishment of adsorbed oxygen ions on the surface. We determined the relation between sensor response (sensitivity) and the amounts of adsorbed oxygen ions (O_(2(ads))^-,O_((ads),)^- O_2(ads)^(2-),O_((ads))^(2-)), water/hydroxide groups (H2O/OH^-), oxygen vacancies (〖V_O^•,V〗_O^(••)), and ordinary lattice oxygen ions (O_lattice^(2-)) as a function of temperature. During hydrogen (H2) testing, the different oxidation states (W6+, W5+, and W4+) of WO3 were quantified and correlated with oxygen vacancy formation (〖V_O^•,V〗_O^(••)). We used a combined application of XPS, UPS, XPEEM-LEEM, and chemical, electrical and sensory analysis for H2 sensing. We established a correlation between the H2 sensing mechanism of WO3, sensor signal magnitude, the amount of adsorbed oxygen ions, and sensor testing temperature. This paper also provides a review of the detection, quantification, and identification of different adsorbed oxygen species. The different surface and bulk-sensitive characterization techniques relevant to analyzing the SMOs-based sensor are tabulated, providing the sensor designer with the chemical, physical, and electronic information extracted from each technique.

The altered nature of archaeological metals means they deteriorate at conditions where metals would be stable. The study of deterioration for such materials is hampered by their complexity, variability and difficulties in measuring deterioration. Placing an object in a sealed container, controlling the RH and pollutant gases and measuring any decrease in oxygen concentration is an accessible method to measure deterioration rate. It has been used for research into suitable environmental conditions to manage deterioration rates of such artefacts including differences in response for artefacts from different excavation sites. Some objects need careful control of RH to low values, this is expensive to maintain and poses risks to other artefacts displayed together. Many objects are actually stable up to quite high RH values and oxygen depletion testing has been used to identify those that can be safely displayed with minimal environmental control. The accelerated corrosion, ‘Oddy’ test is frequently used to sift out unsuitable display materials. The visual assessment is widely recognized to be subjective. The test container has been modified and oxygen depletion appears to give good quantitative measurements of corrosion that correspond with both visual comparison and corrosion quantification for copper, lead and steel, but not for silver.

Multiple myeloma (MM) accounts for about 10 to 15% of all diagnosed hematologic malignancies and about 1-2% of all cancer cases. Approximately 80-90% of MM patients develop bone disease and the changes rarely regress. It is only possible to stop or slow their progression. A major role in bone destruction in MM is attributed to the Wnt signaling pathway, and its action can be modified by various types of interventions including training and diet. Therefore, the aim of this project was to evaluate the effects of a Nordic Walking (NW) training cycle and intermittent fasting (IF) on the levels of selected bone turnover markers associated with the Wnt pathway in patients with MM. Results from 35 patients divided into training (NW and IF NW) and non-training (IF and control) groups were included in the analysis. A 6-week training cycle involving 60-minute workouts 3 times a week was conducted. Body mass and composition and the levels of: vitamin D, calcium and phosphorus, beta2-microglobulin and albumin were examined before and after completion of training cycle. Markers of bone turnover were also determined: sclerostin (SOST), Dickkopf-related protein 1 (DKK-1), osteoprotegrin (OPG), osteopontin (OPN) and Tartrate-resistant acid phos-phatase 5b (TRACP 5b). There was no negative effect of IF or combined training and fasting on the nutritional status of the patients (the level of albumines was unchanged). Both training groups showed an increase in serum concentrations of the active metabolite of vitamin D (IF NW and NW: p=0.001 and p=0.022, re-spectively). The change in the concentration of this vitamin negatively correlated with the con-centration of TRACP 5b (r=-0.413, p=0.014). Evaluating the concentrations of markers related to bone turnover, a reduction in the concentrations of SOST (time: p=0.026, time vs. group: p=0.033) and TRACP 5b (time: p

The aim of the study is to obtain a more complete picture of the blood plasma melatonin concentration in the donkey species. To this purpose sampling and statistical processing were carried out in such a way that allowed to establish the annual and daily rhythm. Based on human observations, according to the hypothesis of the authors, the blood plasma melatonin concentration of pregnant individuals rises during late gestational period, before parturition. To confirm this, the melatonin concentration of pregnant and non-pregnant mares was monitored and compared. In regard to the circannual rhythm, the significantly lowest midnight melatonin value (27.67 pg/ml) is typical for the summer solstice. Under consideration of circadian changes, a significantly strongest melatonin production (45.16 pg/ml) can be observed on the night of the winter solstice (p &lt; 0.001). Considering the gestational age, the blood plasma melatonin concentration (around 38 pg/ml) does not change as pregnancy progresses (p = 0.136). The results obtained in the study population of the domestic ass usefully expand the little knowledge previously gathered about the development of blood plasma melatonin concentration of this species.

PDMS samples may be used in various microfluidic applications by hydrophilizing their surfaces. This study examines the effects of air plasma jet (APJ) and dielectric barrier discharge (DBD) plasma on the surface hydrophilicity of polydimethylsiloxane. In order to increase the hydrophilicity of PDMS sample surfaces, two plasma sources including APJ and DBD were compared. Both DBD and APJ setups were measured for voltage and current, and their respective power was calculated and compared based on their characteristics. It is important to note that the electrical specifications of APJ and DBD were identical, and the source power rates for APJ and DBD plasma were 306W and 300W respectively. UV-vis spectroscopy was used to characterize the plasma, and an electrical characterization of the plasma's power supply was carried out. The effects of parameters such as the distance from the nozzle tip, the duration of the process, and the source voltage on the hydrophilicity of the surfaces during the treatment by APJ were also examined, and samples were then examined for a period of time to determine whether surface hydrophilicity was preserved. On the PDMS surface, a contact angle of about 5.1° was observed using short-term plasma treatments of 10 seconds. In the same conditions, the effect of DBD treatment was superior to that of APJ treatment.

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

Lung cancer is the leading cause of cancer related mortality worldwide. In order to improve its overall survival, early diagnosis is required. Since current screening methods still face some pitfalls, such as high false positive rates for low-dose computed tomography, researchers are still looking for early biomarkers to complement existing screening techniques in order to provide a safe, faster and more accurate diagnosis. Biomarkers are biological molecules found in body fluids, such as plasma, that can be used to diagnose a condition or disease. Metabolomics has already shown to be a powerful tool in the search for cancer biomarkers since cancer cells are characterised by impaired metabolism, resulting in an adapted plasma metabolite profile. The metabolite profile can be determined using nuclear magnetic resonance, or NMR. Although metabolomics and NMR metabolite profiling of blood plasma are still under investigation, there is already evidence for its potential for early-stage lung cancer diagnosis, therapy response, and follow-up monitoring. This review highlights some key breakthroughs in this research field, where the most significant biomarkers will be discussed in relation with their metabolic pathways and in light of the altered cancer metabolism.

The incidence of diabetes mellitus (DM) continues to rise worldwide and one of the most serious microvascular complications is diabetic kidney disease (DKD), which is the leading cause of end-stage renal disease. Current bi-omarkers such as urinary albumin excretion rate have limitation for early detection of DKD. In our study we used ultra-high-performance liquid chromatography coupled with electrospray ionization-quadrupole-time of flight-mass spectrometry (UHPLC-QTOF-ESI+-MS) techniques to quantify previously analyzed metabolites, such as tryptophan, kynurenic acid, taurine, l-acetylcarnitine, glycine, and tiglylglycine. We performed the targeted analy-sis of metabolites from urine and serum samples, collected from 110 subjects. Of these, 90 patients with type 2 DM (T2DM) were divided according to the urinary albumin/creatinine ratio (UACR) into normoalbuminuria 300 mg/g groups, respectively, while 20 subjects were rep-resented by healthy controls. Through various validation methods, we identified several metabolites as potential biomarkers, such as kynurenic acid, glycine, and l-tryptophan in serum and l-acetylcarnitine, tiglylglycine, and tau-rine in urine.

Simulations based on Supernova (SN) observations predict several galactic SN explosions (SNe) occur every century. Unlike SNes within the Interstellar Medium (ISM) where ambient gas generally absorbs blast waves within a million years, SNes occurring in a rarified environment outside of the (ISM) generate blast waves which remain in a high velocity free expansion phase for more extended periods. The SN blast wave forms an expanding spherical shell and when multiple blast waves intersect, the overlapping region naturally takes the form of a ring, an arc, or an Einstein Cross structure. The analysis shows the high velocity plasma establishes a medium with permeability which drives the index of refraction greater than 1. As a result, when a shock discontinuity forms in the overlapping region, light is reflected from the host galaxy which exposes the intersecting blast wave regions. The expanding shells are shown to induce an achromatic redshift to the reflected light consistent with those measured for gravitational lenses. Further, it is shown that a Hubble equation for a blast wave around the Milky Way Galaxy can be parameterized to align with measured redshifts of extragalactic light fields over a wide range of distances.

Luminescence-based sensors for measuring oxygen concentration are widely used both in industry and research due to the practical advantages and sensitivity of this type of sensing. The measuring principle is the luminescence quenching by oxygen molecules, which results in a change of the luminescence decay time and intensity. In the standard approach, this change is related to an oxygen concentration using the Stern–Volmer equation. This equation, which in most of the cases is non-linear, is parametrized through device-specific constants. Therefore, to determine these parameters every sensor needs to be precisely calibrated at one or more known concentrations. This work explores an entirely new artificial intelligence approach and demonstrates the feasibility of oxygen sensing through machine learning. The specifically developed neural network learns very efficiently to relate the input quantities to the oxygen concentration. The results show a mean deviation of the predicted from the measured concentration of 0.5 % air, comparable to many commercial and low-cost sensors. Since the network was trained using synthetically generated data, the accuracy of the model predictions is limited by the ability of the generated data to describe the measured data, opening up future possibilities for significant improvement by using a large number of experimental measurements for training. The approach described in this work demonstrates the applicability of artificial intelligence to sensing technology and paves the road for the next generation of sensors.

The increasing emergence of multidrug resistant (MDR) pathogens causes difficult-to-treat infections, with long-term hospitalizations and high incidence of death, thus representing a global public health problem. To manage MDR bacteria bugs, new antimicrobial strategies are necessary, and their introduction in practice is a daily challenge for scientists in the field. An extensively studied approach to treat MDR infections consists in inducing high levels of reactive oxygen species (ROS) by several methods. Although further clinical investigations are mandatory on the possible toxic effects of ROS to mammalian cells, clinical evaluations are extremely promising, and their topical use to treat infected wounds and ulcers, also in presence of biofilm, is already clinically approved. Biochar (BC) is a carbonaceous material obtained by pyrolysis of different vegetable and animal biomass feedstocks, at 200−1000 °C in limited presence of O2. Recently, it has been demonstrated that BC capability of removing organic and inorganic xenobiotics is mainly due to the presence of persistent free radicals (PFRs), which can activate oxygen, H2O2 or persulfate in the presence or not of transition metals by electron transfer thus generating ROS, which in turn degrade pollutants by advanced oxidation processes (AOPs). In this context, the antibacterial effects of BC containing PFRs have been demonstrated by some authors against Escherichia coli and Staphylococcus aureus, thus giving birth to our idea of the possible use of BC-derived PFRs as a novel method capable of inducing ROS generation for antimicrobial oxidative therapy. Here, the general aspects concerning ROS physiological and pathological production and regulation, and the mechanism by which they could exert antimicrobial effects have been reviewed. The methods currently adopted to induce ROS production for antimicrobial oxidative therapy have been discussed. Finally, for the first time, BC-related PFRs have been proposed as a new source of ROS for antimicrobial therapy via AOPs.

Objectives: To rate the effects of low molecular weight hyaluronic acid (LMWHA) solution and high concentration oxygen (HCO) through a specific medical device (Caress Flow©), compared to topical administration of hyaluronic acid (HA) alone on symptoms of mild and moderate stress and mixed urinary incontinence in women with genitourinary syndrome of menopause (GSM). Methods: A total of 68 postmenopausal women were enrolled (from October 2021 to September 2023). Patients were separated in two groups: one group used therapy with LMWHA solution and HCO combined and the second group used therapy with HA alone. Patient Global Impres-sion of Improvement (PGI-I) as the first outcome was used. As secondary outcomes International Consultation on Incontinence Questionnaire - short form (ICIQ-SF) questionnaire and Internation-al Quality of Life (IQoL) questionnaire were used. Results: Sixty-eight (68) women, 35 (51%) and 33 (49%), were treated with LMWHA solution and HCO combined and HA alone for 10 weeks, respectively. 28 (80%) versus 7 (20%) women reported an improvement (PGI-I score ≤3) of the symptoms in LMWHA solution and HCO com-bined group versus HA alone group. According to the ICIQ-SF, a statistically significant differ-ence was recorded after treatment between the two groups (median, 7 [5-11] vs 10 [8-11]; P = 0.03). According to the IQoL questionnaire, a statistically significantly lower median score was recorded in the LMWHA solution and HCO combined compared with the HA group, before (71 [IQR 55-81] vs 89 [IQR 67-94]; P < 0.01) and after (78 [IQR 65-86] vs 88 [IQR 72-99]; P = 0.04) treatment. Conclusions: LMWHA solution and HCO combined might improve the mild and moderate stress and mixed urinary incontinence in this set of women and that it is superior to HA therapy alone. However, these results need to be confirmed in further studies with a controlled design and a larger population.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Natural cytokinins are a promising group of cytoprotective and anti-tumor agents. In this research, we synthesized a set of novel cytokinin analogs with alkyl substituents at various positions of the aromatic moiety, as well as with oxygen-containing groups, and tested their antiproliferative activity in MDA-MB-231, A-375, and U-87 MG cell lines, and cytoprotective properties in H2O2 and CoCl2 models. Two amino-linked compounds were anti-proliferative with the ability to act synergistically with doxorubicin, and two carbamate-based ones were cytoprotective. According to the molecular docking data, anti-proliferation was based on the A2AR and APRT inhibition and cytoprotection on the CDK2 inhibition. The obtained results are promising for the development of novel anti-cancer therapeutics.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

Cutaneous mycoses are common infections whose treatment has become more complex due to increasing antifungal resistance and the need for prolonged therapies, hindering patient adher-ence and increasing the incidence of adverse effects. Consequently, the use of physical therapies, especially photodynamic therapy (PDT), has increased for the treatment of onychomycosis due to its antimicrobial capacity mediated by the production of reactive oxygen species. This study investigates the in vitro effect of the combination of blue light (448 nm) and red light (645 nm) with terbinafine on the cell viability of human keratinocytes and the production of reactive ox-ygen species. The combination of terbinafine and blue light exhibits a synergistic effect on the production of reactive oxygen species and a significant increase in the expression of superoxide dismutase (SOD), an enzyme involved in the reduction of superoxide ions (O2-) and the genera-tion of hydrogen peroxide (H2O2). Such effect could be useful in clinical practice to improve the response of cutaneous mycoses to pharmacological treatment, reduce their toxicity, and shorten their duration.

BACKGROUND This study investigated the association of postprandial plasma glucose (PPG) with cancer mortality using a general cohort of US adults. METHODS This cohort study included 14,860 US adults who attended the third National Health and Nutrition Examination Survey from 1988 to 1994, with mortality being followed up to December 31, 2019. The experimental exposures were levels of plasma glucose, including PPG with a fasting time of 0-3.9 h (PPG_0-3.9h) and 4-7.9 h (PPG_4-7.9h), plasma glucose with a fasting time ≥ 8 h (PG_fasting), and plasma glucose at 2 h after oral glucose tolerance test (PG_2hOGTT). Plasma glucose-associated cancer mortality risk was assessed using Cox proportional hazards models. RESULTS A 1-natural-log-unit increase in PPG_4-7.9h was associated with a higher multivariate-adjusted risk for cancer mortality [hazard ratio (HR), 3.24; 95% confidence interval (CI), 1.50-7.00]. However, PPG_0-3.9h, PG_fasting, PG_2hOGTT, hemoglobin A_1c, and insulin were not significantly associated with cancer mortality. The positive association of PPG_4-7.9h with cancer mortality remained in those without a prior diagnosis of cancer. CONCLUSIONS High PPG_4-7.9h is associated with a higher cancer mortality risk in US adults. Lowering PPG_4-7.9h may reduce cancer mortality.

We recently demonstrated the effectiveness of long-term treatment with rifaximin and the probiotic VSL#3 at improving urogenital and gastrointestinal symptoms in patients with both chronic inflammatory prostatitis (IIIa prostatitis) and diarrhea-predominant irritable bowel syndrome (IBS-D), relative to patients with IBS-D alone. Because low-grade inflammation of the intestine and prostate may be one of the reasons for co-developing both IIIa prostatitis and IBS-D, we designed the present study to once again evaluate the efficacy of combined rifaximin and VSL#3 treatment in patients affected by IIIa prostatitis plus IBS-D, but we also measured seminal plasma pro-inflammatory (IL-6) and anti-inflammatory (IL-10) cytokines before and after treatment. We consecutively enrolled 124 patients with IIIa prostatitis and IBS-D (diagnosed using the Rome III criteria). Patients were randomized into two groups: group A (n=64) was treated with rifaximin (seven days per month for three months) followed by VSL#3, and group B (n=60) was treated with a placebo. At the beginning of the study and after three months of treatment, all patients completed NIH-CPSI and IBS-SSS questionnaires to score the severity of their urogenital and gastrointestinal symptoms, and we measured seminal plasma levels of IL-6 and IL-10 using ELISA. We defined patients who improved following the treatment as those with a ≥6-point reduction in their NIH-CPSI score or ≥50-point reduction in their IBS-SSS score. By the end of the intervention, 68.7% and 62.5% of patients from group A reported improved NIH-CPSI and IBS-SSS scores, respectively, compared to only 3.3% and 5% of the placebo group. Group A patients also had significantly lower mean seminal plasma levels of IL-6 (11.3 vs 32.4 pg/mL) and significantly higher mean levels of IL-10 (7.9 vs 4.4 pg/mL) relative to baseline, whereas levels of IL-6 and Il-10 did not change in the placebo group. The co-occurrence of two clinical phenotypes (IBS-D plus IIIa prostatitis) result in increased intestinal inflammation and altered immune activation, both of which can be balanced by treatment with rifaximin and VSL#3.

Background/Objectives: Encouraging results reported of Platelet-Rich Plasma (PRP) treatment for knee osteoarthritis (KOA). The present retrospective study reports the efficacy and safety of a high dose of neutrophile and red blood cell-depleted PRP to treat 212 patients with KOA. Methods: 212 consecutive patients diagnosed with Kellgren-Lawrence (KL) grading 1-3 KOA chronic knee pain for at least 1 year were treated with 3 injections at 15-day intervals with a high dose of neutrophil-depleted PRP (4 billion platelets). Clinical outcomes were retrospectively recorded as a percentage of responders at 3,6, and 12-month follow-up, following the OMERACT-OARSI criteria. Pain through VAS score and WOMAC score have also been recorded. Results: 4ml of PRP containing 4X109 platelets were obtained by single spin centrifugation and injected intra-articular into each patient with no pre-activation. The overall responder rate of patients responding to OMERACT-OARSI criteria at 3,6,12 months was 68.9%, 72,7% and 70,6%. There was a significant improvement in VAS and WOMAC scores at 3-, 6- and 12-month follow-up compared to the pre-treatment value (p&lt; 0.01). The lowest VAS score was observed at 6 months overall and in all three-grade KL groups. KL2 groups showed the best results regarding pain reduction and WOMAC score at 6 months (p&lt; 0.01). Conclusions: a high dose of neutrophil-depleted PRP is an effective treatment for KL1-3 KOA. It provides symptomatic relief, can potentially reduce disease progression, and has sustained effects for up to 12 months.

In this study, Plasma-Activated Water (PAW) was synthesized using a coaxial Dielectric Barrier Discharge (DBD) reactor, benefiting from the elevated capacity of air-flow-assisted DBD discharges to enhance nitrogen-based species concentration. By manipulating operational parameters, including gas flow rate, activation time, and DI water volume, we achieved significant concentrations of Reactive Oxygen and Nitrogen Species (RONS). As a result, the PAW obtained displayed pronounced physicochemical attributes: a pH of 2.06, an ORP of 275mV, conductivity of 3mS/cm, and TDS of 1200 mg/L. A pivotal aspect of this research was the evaluation of the reactor's efficiency, as indicated by metrics like the specific input energy and ozone efficiency yield. The antimicrobial potential of the PAW was also assessed against pathogenic microbes, with remarkable reductions in viability for both Staphylococcus aureus and Escherichia coli (99.99%) and a more moderate decrease for Candida albicans (37%). These findings underscore the capability of the coaxial DBD reactor in crafting high-quality PAW with significant antimicrobial properties, necessitating further studies to validate its broad-spectrum and safe application.

Oxygen extraction fraction (OEF), the fraction of oxygen that tissue extracts from blood, is an es-sential biomarker for directly assessing tissue viability and function in neurologic disorders. For quantitative mapping of OEF, an integrative model of quantitative susceptibility mapping and quantitative blood oxygen level-dependent magnitude (QSM+qBOLD or QQ) was recently pro-posed. However, QQ assumes Gaussian noise in both susceptibility and multi-echo gradient echo (mGRE) magnitude signals for OEF estimation. This assumption is unreliable in low sig-nal-to-noise ratio (SNR) regions like disease-related lesions, risking inaccurate OEF estimation and potentially impacting clinical decisions. Addressing this, our study presents a novel multi-echo complex QQ (mcQQ) that models realistic noise in mGRE complex signals. The proposed mcQQ was implemented using a deep learning framework (mcQQ-NET) and compared with the existing deep learning-based QQ (QQ-NET) in simulations, ischemic stroke patients, and healthy subjects. Both mcQQ-NET and QQ-NET used identical training and testing datasets and schemes for a fair comparison. In simulations, mcQQ-NET provided more accurate OEF than QQ-NET. In the sub-acute stroke patients, mcQQ-NET showed a lower average OEF ratio in lesions relative to unaf-fected contralateral normal tissue than QQ-NET. In the healthy subjects, mcQQ-NET provided uniform OEF maps, similar to QQ-NET, but without unrealistically high OEF outliers in areas of low SNR. Therefore, mcQQ-NET improves OEF accuracy by better reflecting realistic data noise characteristics.

In this study, we evaluated the antibacterial effect against Staphylococcus aureus and Salmonella Typhimurium in fried fish paste using floating electrode-dielectric barrier discharge (FE-DBD) plasma (1.1 kV, 43 kHz, N2 1.5 m/s, 1-60 min). In addition, quality evaluation (pH, VBN) of fried fish paste was conducted after FE-DBD plasma treatment. When FE-DBD plasma was treated for 1, 5, 10, 20, 30 and 60 min, S. aureus decreased by 0.16-1.13 log10 CFU/g, and S. Typhimurium decreased 0.25-1.13 log10 CFU/g. Both decreased &gt; log10 CFU/g at 60 min. The D-value was 58.92 and R2 was 0.97 for S. aureus using first-order kinetics, and the D-value was 43.60 and R2 was 0.97 for S. Typhimurium using the Weibull model. There was no significant difference in pH after FE-DBD plasma treatment (p &gt; 0.05). However, volatile basic nitrogen (VBN) significantly decreased as the treatment time increased (p &lt; 0.05), and it was the lowest at 60 min to 3.46. Therefore, FE-DBD plasma treatment could be considered as a technology for preserving the quality of processed foods.

We present a laser-plasma electron accelerator module designed to be driven by high repetition rate lasers for industrial applications of laser-driven electron beams. It consists of a single vacuum chamber containing all the necessary components for producing, optimizing, and monitoring electron beams generated via laser wakefield acceleration in a gas jet. The core methods involve comprehensive metrological assessments, including rigorous temporal laser pulse characterization and contrast measurements, supplemented by detailed spatio-temporal distribution analyses of the laser system. Results demonstrate the good stability and reproducibility of the laser system, confirming its suitability for advanced scientific and industrial applications. We demonstrate the full functionality of the laser-plasma accelerator module and perform target density and laser-plasma characterizations. Our work is a first step towards the wide dissemination of fully integrated laser-plasma accelerator technology.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

The coexistence of SAH with T2DM is a common comorbidity. In this present study, we investigated the link between altered plasma antioxidant trace elements (ATE: Manganese, Selenium, Zinc and Copper) and fatty acids ratio (FAR: polyunsaturated/saturated) imbalance as transition biomarkers between vascular pathology (SAH) to metabolic pathology (T2DM). Our data revealed strong correlation between plasma ATE and FAR profile which is modified during SAH-T2DM association compared to healthy group. This relationship is mediated by lipotoxicity (simultaneously prominent visceral adipose tissue lipolysis, significant flow of non-esterified free fatty acids release, TG-Chol-dyslipidemia, high association of Total SFA, Palmitic acid, Arachidonic acid and PUFA 6/ PUFA 3; drop in tandem of PUFA / SFA and EPA+DHA); oxidative stress (lipid peroxidation confirmed by TAS depletion and MDA raise, concurrently drop of Zn/Cu-SOD, GPx, GSH, Se, Zn, Se/Mn, Zn/Cu; concomitantly enhance Cu, Mn and Fe); endothelial dysfunction (endotheline-1 increase); athero-thrombogenesis risk (concomitantly raise of ApoB100/ApoA1, Ox-LDL, tHcy and Lp(a)) and inflammation (higher of Hs-CRP, Fibrinogen and Ferritin). Our study open to new therapeutic targets and to better dietary management, such as to establish dietary ATE and PUFA 6 / PUFA 3 or PUFA / SFA reference values for atherosclerotic risk prevention in hypertensive-diabetics patients.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

As the world’s population age, Cognitive Frailty (CF) is becoming one of the most serious health problems and elucidating its biological mechanisms along with prevention and treatments becomes increasingly important also considering the associated health costs. This pilot study aims to investigate the potential cognitive and neuropsychological effects of a 5-week treatment with a therapy based on the regenerative properties of ozone (O3) in a cohort of patients stratified according to CF. We also study the potential effects of O3 on blood-based biomarkers indicative of specific biological systems that may be altered in CF. Seventy-five older persons have been recruited and randomly assigned to receive the active treatment (150cc of oxygen-O2-O3 mixture at the concentration of 30ug of O3 per cc of O2) or O2, or the placebo (air) for 5 weeks. The primary endpoint is a change in the scores of clinical scales from baseline (T0) to weeks 3 (T3), 9 (T9), 15 (T15) after treatment. The secondary endpoint is a change in biomarkers levels resulting from transcriptomics, proteomics and metabolomic patterns at the same times. This study will evaluate whether an intervention with the O2-O3 therapy could have potential cognitive, neuropsychological and biological effects on CF.

Gestational diabetes mellitus (GDM) triggers alterations in the maternal gut microbiome. Alongside metabolic shifts, microbial products may impact clinical factors and influence pregnancy outcomes. Here, we performed two separate analyses to integrate the maternal microbiome-metabolomic differences from a subset of the “Choosing Healthy Options in Carbohydrate Energy” (CHOICE) study. Women diagnosed with GDM were randomized to a diet higher in complex carbohydrates (CHOICE, n=18, 60% complex carbohydrate/25% fat/15% protein) or a conventional GDM diet (CONV, n=16, 40% carbohydrate/45% fat/15% protein). All meals were provided, diets were eucaloric, and fiber content was similar. CHOICE diet was associated with increases in TMAO, lysophosphotidylcholines, indoxyl sulfate, and several triglyceride (TG) species, while CONV diet was associated with higher plasma hippuric acid, aspartic acid, betaine, glutamic acid, indole propionic acid, and indoleacetic acid, suggesting that differences in lipid metabolism and tryptophan utilization pathways are linked to specific maternal diets. We also identified two latent metabolic groups not associated with either diet treatment: one metabolome associated with higher fasting glucose, and the other associated with higher fasting TGs after 7 weeks on either diet. Our study underscores the importance of utilizing dietary approaches to optimize maternal-fetal health outcomes in GDM treatment.

Considerable amounts of agro-industrial by-products are discarded or burnt as fuel every year. However, they can be utilized as a valuable source of fiber, phenolics and other useful compounds such as antioxidants. The profile of beneficial compounds can be affected by genotype, locality, orchard management and productive season, adding or decreasing the bioactive potential of by-products. In this study, hazelnut (Corylus avellana L.) and walnut (Juglans regia L.) nutshells were investigated for their fiber content and antioxidant capacity as valorized by-products for the industry. Determinations (ORAC, TPC and color asses) were performed in hazelnut and walnut orchards located in Southern Chile during three consecutive seasons (2020/21; 2021/22 and 2022/23). Analyses of oxygen radical absorbance capacity (ORAC) in nutshells showed the highest ORAC from both species in the season 2020/21 (3217 µmol TE g1DW for hazelnut shells and 4663 µmol TE g DW1 for walnut shells), while variability in the consecutive seasons was lower for hazelnut than in walnut. Total phenolic content in hazelnut shells was positively correlated with L* (R: 0.883) and E (R: 0.924) during 2020/21 season, also with L* for 2022/23 (R: 0.907). While ORAC was negatively correlated with L* (R: 0.922) in 2021/22. In addition, morphological and structural features of both nutshells examined by Scavenging Electron Microscopy (VP-SEM) and Confocal Scavenging Laser Microscopy (CSLM) revealed differential tissue distribution and accumulation patterns of both cellulose and lignin. On the other hand, photo-colorimetric values were determined for both shells and corresponding seasons, and non-significative differences were found both shells and among seasons Finally, these results provide insight into the physicochemical characteristics of two shell types which should be considered together with antioxidant capacity in their valorization as a residual material.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

Good hand hygiene has proven to be essential in reducing the uncontrolled spread of human pathogens. Cold atmospheric plasma (CAP) may provide an alternative to disinfecting hands with ethanol-based handrubs when hand washing facilities are unavailable. CAP can be safely applied to the skin if the energy is well controlled. In this study, RF and DC plasma sources was built with a pin-to-mesh electrodes configuration inside a fused silica tube of 5 mm of inner diameter. Microbiological assays based on EN 13697:2015+A1:2019 using Escherichia coli DSM 682 or Staphylococcus epidermidis DSM 20044 were used to examine the antimicrobial effect of various plasma conditions. Metal and silicone disks that model skin were used as inoculation matrices. The prototype air radio frequency (RF) CAP achieved significant disinfection in the MHz range on stainless steel and silicone substrates. This is equivalent to half the performance of direct current CAP, which is only effective on conductive substrates. Using only electricity and air CAP could, with further optimization, replace or complement current hand disinfection methods, and mitigate the economic burden of public health crises in the future.

Abstract: Plasma hemopexin (HPX) is the key antioxidant protein of the endogenous clearance pathway that limits the deleterious effects of heme released from hemoglobin and myoglobin. During intra-vascular hemolysis, heme partitioning to protein and lipid increases as the plasma concentration of HPX declines. Therefore, the development of HPX as a replacement therapy during high heme stress could be a relevant intervention for hemolytic disorders. A logical approach to enhance HPX yield involves recombinant production strategies from human cell lines. The present study focuses on a biophysical assessment of heme binding to recombinant human HPX (rhHPX) produced in the Expi293FTM (HEK293) cell system. In this report, we examine rhHPX in comparison with plasma HPX using a systematic analysis of protein structural and functional characteristics related to heme binding. Analysis of rhHPX by UV/Vis absorption spectroscopy, circular dichroism (CD), SEC-HPLC and catalase-like activity demonstrated a similarity to HPX fractionated from plasma. In particular, the titration of HPX apo-protein(s) with heme was performed for the first time using a wide range of heme concentrations to model HPX-heme interactions to approximate physiological conditions (from extremely low to more than 2-fold heme excess). The CD titration data showed an induced bisignate CD Soret band pattern typical for plasma and rhHPX versions at low heme-to-protein molar ratios and demonstrated that further titration is dependent on the amount of protein-bound heme to the extent that the arising opposite CD couplet results in a complete inversion of the observed CD pattern. The data generated in this study suggests more than one binding site in both plasma and rhHPX. Further, our study provides a useful analytical platform for detailed characterization of HPX-heme interactions and potentially, novel HPX fusion constructs.

This article reports new measurements of laser-induced plasma hypersonic expansion measurements of diatomic molecular cyanide (CN). Focused, high-peak power 1064-nm Q-switched radiation of the order of 1 TW/cm² generates optical breakdown plasma in a cell containing a 1:1 molar gas mixture of N₂ and CO₂ at a fixed pressure of 1.1 × 10⁵ Pascal and in a 100 ml/min flow of the mixture. Line-of-sight (LOS) analysis of recorded molecular spectra indicate the outgoing shockwave at expansion speeds well in excess of Mach number 5. Spectra of atomic carbon confirm an increased electron density near the shock wave, and equally, molecular CN spectra reveal higher excitation temperature near the shockwave. The results are consistent with corresponding high-speed shadow graphs obtained by visualization with an effective shutter speed of five n anosecond. In addition, LOS analysis and application of integral inversion techniques allow inferences about the spatio-temporal distribution of the plasma.

Plasma being the fourth and most abundant form of matter extensively exists in the universe in the inter-galactic regions. It provides an electrically neutral medium of unbound negative and positive charged particles, which has been produced by subjecting air and various other gaseous mixtures to strengthen the electromagnetic field and by heating compressed air or inert gasses for creating negative and positive charged particles known as ions. Nowadays, many researchers are paying attention to the formation of artificial Plasma and its potential benefits for mankind. The literature is sparsely populated with the applications of Plasma. This paper presents specific methods of generation and applications of Plasma, which benefits humankind in various fields, such as in electrical, mechanical, chemical and medical fields. These applications include hydrogen production from alcohol, copper bonding, semiconductor processing, surface treatment, Plasma polymerization, coating, Plasma display panels, antenna beam forming, nanotechnology, Plasma Torch, Plasma pencils, low-current non-thermal Plasmatron, treatment of prostate cancer, Plasma source ion implantation, cutting by Plasma, Plasma etching, pollution control, neutralization of liquid radioactive waste, etc. Resultantly, worth of Plasma technology in the medical industry is increasing exponentially that is closing the gap between its benefits and cost of equipment used for generating and controlling it.

Iron-based materials are widely applied in Fenton chemistry and they have promising prospects in the processing of wastewater. The composition complexity and rich chemistry of iron and/or oxides, however, hamper the precise understanding on the active sites and the working mechanism which still remain highly controversial. Herein, iron oxides of four different model systems are designed through a conventional precipitation method plus H2 reduction treatment. These systems feature Fe@Fe3O4 with abundant oxygen vacancy, Fe0 and Fe3O4 particles with interface structures, and Fe3O4-dominated nanoparticles of different sizes. These materials are applied in the decomposition of methyl orange as a model reaction to assess the Fenton chemistry. The Fe@Fe3O4 with core-shell structures exhibited significantly higher decomposition activity than the other Fe3O4-rich nanoparticles. A thin Fe3O4 layer formed by auto-oxidation of iron particles when exposing to air can boost the activity as compared with the Fe0 and Fe3O4 particles with interface structures but poor oxygen vacancy. The unique hetero-structure with the co-existence of both metallic iron and oxygen vacancy displayed excellent redox propensity which might account for the superior Fenton activity. This finding provides a new perspective to understand and design highly efficient iron-based Fenton catalysts.

Telomere repeats at the ends of human chromosomes protect chromosomes from degradation, and telomerase has a prominent role in telomere maintenance. Telomerase also affects cell proliferation, DNA replication, differentiation, and tumourigenesis. TERT (telomerase reverse transcriptase enzyme) is the catalytic subunit of telomerase and is critical for enzyme activity. TERT promoter mutations and promoter methylation are strongly associated with increased telomerase activation in cancer cells. Notably, TERT and telomerase are downregulated in stem cells during their differentiation. Therefore, the link between differentiation and telomerase provides a valuable tool for studying the epigenetic regulation of TERT enzyme. Oxygen tension affects several cellular behaviours including proliferation, metabolic activity, stemness, and differentiation. The role of oxygen tension in driving promoter modifications of the TERT gene in embryonic stem cells (ESCs) is poorly understood either in vitro or in vivo. We adopted a monolayer ESCs differentiation model to explore the role of low, physiological, oxygen (physoxia) in the epigenetic regulation of telomerase and associated genes, including TERT, DNMTs, and HDACs. Cells were cultured in either air, a 2% O2 incubator, or a 2% O2 oxygen workstation to provide a fully defined 2% O2 environment. Pre-gassed media (pre-conditioned to 2% O2 in a HypoxyCool unit) was used in all 2% O2 experimentation. As anticipated, physoxia culture increased the proliferation rate and stemness of ESCs and a slower onset of differentiation in physoxia was evident. Further, downregulated TERT expression was correlated to reduced telomerase activity during differentiation. TERT expression and telomerase activity remained significantly elevated in physoxia during differentiation. A substantial increase in TERT promoter methylation levels was noted during differentiation. Chemical inhibition of DNMT3B reduced TERT promoter methylation and was associated with increased TERT gene and telomerase activity during differentiation. DNMT3B CHiP demonstrated that downregulated TERT expression and increased proximal promoter methylation were associated with DNMT3B binding to the promoter. In conclusion, we have demonstrated that DNMT3B can directly bind TERT promoter, change its methylation levels, and contribute to regulation of telomerase activity.

Background: The incidence of various types of cancer, for example papillary thyroid carcinoma (PTC), is on the rise. Since therapeutic success depends greatly on early diagnosis, reliable diag-nostic biomarkers must be identified and easy-to-apply tools for detecting them must urgently be standardized. Here, we contribute to solving this medical challenge by assessing miRNAs sus-pected of promoting carcinogenesis in extracellular vesicles (EVs) that can be routinely obtained via liquid biopsy. We profit from current progress in cancerology that provides innovations in liquid biopsy and EVs analysis along with identification of miRNAs and chaperone system (CS) components implicated in carcinogenesis. Methods: We measured in EVs obtained from circulat-ing blood plasma from PTC patients the levels of three miRNAs implicated in thyroid cancer, miR-1, miR-206, and miR-221, and most likely involved in the regulation of two members of the CS, Hsp60 and CCT. EVs were isolated from the plasma of patients with PTC and controls with benign goiter (BG), and from the culture medium of a PTC cell line (MDAT32) and were duly characterized. Results: The levels of miRNAs determined by RT-qPCR were consistently higher in PTC patients and decreased down to control levels after thyroidectomy. Bioinformatics showed that the miRNAs target genes were associated to the molecular pathogenesis of PTC. Conclusions: Thus, our exploratory study reaffirms the potential in clinics of the selected miRNAs in EVs as useful biomarkers of PTC easily accessible via liquid biopsy, which is minimally invasive and amenable to periodic repetition, an improvement compared to the established fine-needle aspirate biopsy.

Photodynamic therapy (PDT) has garnered significant attention in the fields of cancer treatment and drug-resistant bacteria eradication due to its non-invasive nature and spatiotemporal controllability. Iridium complexes have captivated researchers owing to their tunable structure, exceptional optical properties, and substantial Stokes displacement. However, most of these complexes suffer from aggregation-induced quenching, leading to diminished luminous efficiency. In contrast to conventional photosensitizers, photosensitizers exhibiting aggregation-induced luminescence (AIE) properties retain the ability to generate a large number of reactive oxygen species when aggregated. To overcome these limitations, we designed and synthesized a novel iridium complex named Ir-TPA in this study. It incorporates quinoline triphenylamine cyclomethylated ligands that confer AIE characteristics for Ir-TPA. We systematically investigated the photophysical properties, AIE behavior, spectral features, and reactive oxygen generation capacity of Ir-TPA. The results demonstrate that Ir-TPA exhibits excellent optical properties with pronounced AIE phenomenon and robust capability for producing singlet oxygen species. This work not only introduces a new class of metal iridium complex photosensitizer with AIE attributes but also holds promise for achieving remarkable photodynamic therapeutic effects in future cellular experiments and biological studies.

The kidney and the heart work together in balancing the body circulation and although their physiology is based on strict inter dependence, their performance fulfills different aims. While the heart can rapidly increase its own oxygen consumption to comply with the wide changes in metabolic demand linked to body function, the kidney physiology is primarily designed to maintain a stable metabolic rate and has limited capacity to cope with any steep increase in renal metabolism. In the kidneys the glomerular population filters a large amount of blood and the tubular system has been programmed to reabsorb 99% of filtrate by reabsorbing sodium together with other filtered substances including all glucose molecules. Glucose reabsorption involves the sodium-glucose cotransporters SGLT2 and SGLT1 on the apical membrane in the proximal tubular section; it also enhances bicarbonate formation so as to preserve the acid-base balance. The complex work of reabsorption in the kidney is the main factor in renal oxygen consumption; analysis of renal glucose transport in disease states is providing better understanding of the renal physiology changes that occur when clinical conditions alter the neurohormonal response leading to an increase in glomerular filtration pressure. In this circumstance glomerular hyperfiltration occurs, imposing a higher metabolic demand on kidney physiology and causing progressive renal impairment. Albumin urination is the warning signal of renal engagement over-exertion and most frequently heralds heart failure development, regardless of disease etiology. The review analyzes the mechanisms linked to renal oxygen consumption, focusing on sodium-glucose management.

Scientific theories on the functioning and dysfunction of the human brain require a good understanding of both its development — before and after birth, and through maturation to adulthood — and its evolution from the ancestral primate brain. Adopting a complex-systems approach, here we propose that the apparent uniqueness of humans’ cognitive capacities might best be understood as emerging from multiple nested “virtuous cycles.” In particular, we propose that the intimate link that exists between oxygen metabolic loops, cortical expansion, and ultimately cognitive and social demands is a key driver of genetic developmental programs for the human brain. Overall, our proposed evolutionary model makes explicit mechanistic links between metabolism, molecular and cellular brain heterogeneity, and behaviour that may in time provide a clearer understanding of brain developmental trajectories and their disorders.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O2 plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O2. Plasma production is stimulated with an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formation. The film preparation at RF power 300 W will give the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 x 10-4 Ω-cm. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. This is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.

This paper deals with investigation of changes in geopolymer wettability with increasing mass fraction of high-carbon fly ash and surface treatment by cold atmospheric plasma (CAP). In this study, multiple samples of geopolymers were prepared, including those with 5% and 10% of high-carbon fly ash from coal-fired power station. Wettability of samples was then measured before and after plasma treatment, both on surface and cut surface. While addition of fly ash only had low effect on the wettability, as in most cases, it only lowered the initial contact angle without speeding up the speed of soaking for compact geopolymer and actually slowed the soaking for foamed geopolymer, plasma treatment had significant impact and made the geopolymer hydrophobic.

The properties of coatings obtained using two surface preparation methods were compared: heating and etching by ion bombardment with plasma generation by arc evaporators and heating and etching by a glow discharge. A Ti-TiN-(Ti,Cr,Al)N coating was deposited. The use of a glow discharge provides better resistance of the coating to destruction during the scratch test and wear resistance of metal-cutting tools when turning steel. As the cutting speed increases, the advantage in wear resistance of the coating deposited using a glow discharge increases. During the process of heating and etching by ion bombardment with metal ions, a nanolayer rich in cobalt and tooling elements (iron, molybdenum) is formed in the area of the interface of the coating and the carbide substrate. When heated and etched by a glow discharge, such a layer does not form. When using both methods, there is identical diffusion of tungsten into the coating and diffusion of chromium and possibly titanium into the substrate. Thus, the glow discharge heating and etching method can be effectively used in the process of PVD coating deposition.

Heterocycles are unique precursors for the synthesis of various pharmaceuticals and agrochemicals particularly those possessing N- or O- moieties. The development of methods to prepare heterocycles is of great importance in synthesis of organic compounds, especially the heterocycles which can be found in natural products. The synthesis of nitrogen and oxygen containing heterocycles viz. coumarins, dihydropyrimidinones, imidazoles, isoxazoles and benzimidazoles represented an attractive and demanding work for chemists as these nucleus has found extensive applications in several fields such as material science, analytical chemistry and most importantly in medicinal chemistry. Organic synthesis has been attracted towards the development of new environmental friendly procedures to achieve the goals of green chemistry. The fundamental aspects of green chemistry are use of biocatalysts and environmental benign solvents under mild conditions. The present review article summarized the green synthetic methods and biological activities of nitrogen and oxygen containing heterocycles.

We report on the phosphorescence of singlet oxygen photogenerated through a stimulated Raman process. Nanosecond radiation in the green spectral region focused on hexane induces a Raman transition of the dissolved in the solvent oxygen molecules toward the singlet oxygen state producing a Stokes signal in the near infrared. The excited oxygen relaxes to ground emitting an infrared photon at 1269 nm. While the Stokes signal’s wavelength changes with the pumping light’s wavelength, the wavelength of the phosphorescent photon remains unaltered. The result confirms previously reports on stimulated Raman excitation of singlet oxygen.

Addressing global environmental problem, water splitting to produce hydrogen fuel by solar energy is getting so much attention. In the water splitting, the essential problem to solve is the development of efficient　catalysts for oxygen production. In this paper, having the prospect for a practical application of photocatalysts to artificial photosynthesis, molecular mechanisms in the current literature are briefly reviewed. At first, recent progress in the function of Mn cluster at the natural photosystem II is briefly described. The kinds of devices in which oxygen evolution reaction (OER) catalysts are used were designated; water electrolyzers, photoelectrodes, and photocatalysts. Some methods for analyzing molecular mechanism in OER catalysis, emphasized by FTIR method, are shown briefly. After describing common OER mechanisms, the molecular mechanisms are discussed for TiO2 and BiVO4 photoelectrodes with our novel data, followed by presenting of co-catalysts IrO2, RuO2, NiO2, and other metal oxides for OER catalysts. Recent reports describing OER catalysts of perovskites, layered double hydroxides (LDH), metal-organic frameworks (MOF), single atom catalysts, as well as metal complexes are reviewed. Finally, by comparing with natural photosystem, the requiring factors to improve the activity of the catalysts for artificial photosynthesis will be discussed.

Oxygen based heterocyclic moieties hold an ample range of therapeutic activities. Heterocyclic molecules are nominated as vital components of an extensive array of structural motifs with both biological and pharmaceutical significance. The oxygen-based scaffolds act as anticancer candidates and are also present in numerous phytomolecules viz; irinotecan, camptothecin, topotecan, taxol, taxotere, podophylotoxin, etoposide, daunorubicin and teniposide. The architectural design of numerous structural motifs for amelioration of cancer has become progressively amplified in recent past years. Until now presently there is no strategic treatment which is so capable that can cure cancer from its roots. Henceforth, it is very indispensible to design novel anticancer structural motifs with least side effects. The oxygen containing heterocyclic scaffolds includes flavonoids, pyrans, xanthones and coumarins are of utmost importance in medical chemistry for the mitigation of cancer. This assemblage offers several recent developments as anticancer oxygen containing heterocyclic molecules all-round the globe and attracted the structural motifs of auspicious molecules, along with their mechanistic insights, IC50 values, structure–activity relationships, and molecular docking studies. The encouraging properties discovered by these oxygen-based scaffolds unconditionally engaging them at frontline in invention of potential drug candidates. Consequently, these probably will be of amazing attention to scientists working on the design and synthesis of antitumor candidates.

The surface fluorination of polypropylene (PP) was performed using F2 and O2 gas mixtures with different F2 gas proportions at 25 °C and 13.3 kPa for 1 h. The surface roughness of the fluorinated PP samples was approximately 1.5 times higher than that of the untreated sample (5 nm). The Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results showed that the PP-derived bonds (-C-C- and -CHx) decreased because they were converted into polar groups (-C–O, -CHF-, and -CFx), which increased the surface electronegativity of PP. The variation in the F2 gas proportion in the gas mixture significantly affected the hydrophilicity and surface composition of PP. At F2 gas proportions of <70%, the hydrophilicity of the fluorinated PP samples improved. Notably, the hydrophilic and negatively charged PP surface enhanced the dyeing of the polymer with basic methylene blue (MB). In contrast, at F2 gas proportions of >90%, the PP surface became hydrophobic owing to increased hydrophobic -CF3 bonds. Thus, enhanced PP dyeing can be controlled based on the composition of the F2 and O2 gas mixture.

Worldwide, oral lesions and cancers are still being significant public health conditions. Thus, an introduction of new oral healthcare protocols is becoming essential. Oral diseases are related to many causative factors, manly dental plaque/biofilm due to poor hygiene. New anti-biofilm therapies are needed to develop. The strategies of anti-biofilm therapies should help to control biofilm formation and microbial attachment to dental surfaces. The present review aimed to provide a comprehensive over-view on evidence related to the potential utility of topical oxygen therapy (BlueM formula) as novel oral care therapies in clinical practice.

Photoacoustic imaging is attracting a great deal of interest owing to its distinct advantages over other imaging techniques such as fluorescence or magnetic resonance image. Availability of photoacoustic probes for reactive oxygen and nitrogen species (ROS/RNS) could shed light on a plethora of biological processes mediated by these key intermediates. Tetramethylbenzidine (TMB) is a non-toxic and non-mutagenic colorless dye that develops a distinctive blue color upon oxidation. In this work we have investigated the potential of TMB as photoacoustic probe for ROS/RNS. Our results indicate that TMB reacts with hypochlorite, hydrogen peroxide, singlet oxygen and nitrogen dioxide to produce the blue oxidation product, while ROS such as the superoxide radical anion, sodium peroxide, hydroxyl radical or peroxynitrite yield a colorless oxidation product. TMB does not penetrate Escherichia coli cytoplasm but is capable of detecting singlet oxygen generated in its outer membrane.

Dissolved Oxygen (DO) concentration is a vital parameter that indicates water quality. DO short term forecasting using time series analysis on data collected from an aquaculture pond is presented here. This can provide data support for an early warning system for an improved management of the aquaculture farm. The conventional forecasting approaches are commonly characterized by low accuracy and poor generalization problems. In this article, we present a novel hybrid DO concentration forecasting method with ensemble empirical mode decomposition (EEMD) based LSTM (Long short-term memory) neural network (NN). With this method, first, the sensor data integrity is improved through linear interpolation and moving average filtering methods of data preprocessing. Next, the EEMD algorithm is applied to decompose the original sensor data into multiple intrinsic mode functions (IMFs). Finally, the feature selection is used to carefully select IMFs that are strongly correlated with the original sensor data and integrate both into inputs for the NN. The hybrid EEMD-based LSTM forecasting model is then constructed. Performance of this proposed model in training and validation sets was compared with the observed real sensor data. To obtain the exact evaluation accuracy of the forecasted results of the hybrid EEMD-based LSTM forecasting model, three statistical performance indices were adopted: MAE, MSE, and RMSE. Results presented for short term (12-hour period) and long term (1-month period) give a strong indication of suitability of this method for forecasting DO values.

Cellular oxidation is responsive to external and internal stimulation and is generated via signal molecules in defense mechanisms through networks of cell proliferation, differentiation, intracellular detoxification, bacterial infection, and immune reactions. Oxidative stress is not necessarily harmful per se; it depends on the balance between oxidation and antioxidation cascades, which are induced according to stimuli and can maintain oxygen homeostasis. The reactive oxygen species (ROS) that are generated during influenza virus (IV) infection have critical effects on both the virus and host cells. In this review, we outline the link between viral infection and ROS production, using IV as an example. We introduce the current state of knowledge on the molecular relationship between cellular oxidation mediated by ROS production and various effects of IV infection. We also summarize the potential anti-IV agents that act by targeting oxidative stress.

A heterobifunctional reactive oxygen species (ROS)-responsive linker for directed drug assembly onto and delivery from a quantum dot (QD) nanoparticle carrier was synthesized and coupled to doxorubicin using EDC/sulfo-NHS coupling. The doxorubicin conjugate was characterized using ¹H NMR and LC-MS and subsequently reacted under conditions of ROS formation (Cu²⁺/H₂O₂) resulting in successful and rapid thioacetal oxidative cleavage which was monitored using ¹H NMR. The deprotected amine linker is amenable to peptide or protein conjugation prior to QD assembly or to direct conjugation to cognate reactive groups on ligands that cap the QD surface.

The brain's unique characteristics make it exceptionally susceptible to oxidative stress, which arises from an imbalance between reactive oxygen species (ROS) production, reactive nitrogen species (RNS) production, and antioxidant defense mechanisms. This review explores the factors contributing to the brain vascular tone vulnerability in the presence of oxidative damage, which can be of clinical interest in critically ill patients or presenting acute brain injuries. The brain's high metabolic rate and inefficient electron transport chain in mitochondria lead to significant ROS generation. Moreover, non-replicating neuronal cells and low repair capacity increase susceptibility to oxidative insult. ROS can influence cerebral vascular tone and permeability, with a potential impact on cerebral autoregulation. Different ROS species, including superoxide and hydrogen peroxide, exhibit vasodilatory or vasoconstrictive effects on cerebral blood vessels. Reactive nitrogen species (RNS), particularly NO and peroxynitrite, also exert vasoactive effects. This review further investigates the neuroprotective effects of antioxidants, including superoxide dismutase (SOD), vitamin C, vitamin E, and the glutathione redox system. Various studies suggest that these antioxidants could be used as adjunct therapies to protect the cerebral vascular tone during high oxidative stress conditions. Nevertheless, more extensive research is required to comprehensively grasp the relationship between oxidative stress and cerebrovascular tone, as well as to explore the potential benefits of antioxidants as adjunctive therapies in critical illnesses and acute brain injuries.