We report on the use of quartz-enhanced photoacoustic spectroscopy (QEPAS) for multi-gas detection. Photo-acoustic (PA) spectra of mixtures of water (H2O), ammonia (NH3) and methane (CH4) were measured in the mid-infrared (MIR) wavelength range using a MIR (mid-infrared) optical parametric oscillator (OPO) light source. Highly overlapping absorption spectra is a common challenge for gas spectroscopy. To mitigate this, we use a partial least-squares regression (PLS) method to estimate the mixing ratio and concentrations of the individual gasses. The concentration range explored in the analysis varies from a few parts-per-million (ppm) to thousands of ppm. Spectra obtained from HITRAN and experimental single-molecule reference spectra of each of the molecular species were acquired and used as training data sets. These spectra were used to generate simulated spectra of the gas mixtures (linear combinations of the reference spectra). Here in this proof-of-concept experiment we demonstrate that after an absolute calibration of the QEPAS cell, the PLS analyses could be used to determine concentrations of single molecular species with a relative accuracy within a few % for mixtures of H2O, NH3 and CH4 and with an absolute sensitivity of approximately 300(±50) ppm/V, 50(±5) ppm/V and 5(±2) ppm/V for water, ammonia and methane, respectively. Thus, demonstrating that QEPAS assisted by PLS is a powerful approach to estimate concentrations of individual gas components with considerable spectral overlap, which is a typical scenario for real-life adoptions and applications.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

In economics, especially econometrics, fixed-effects are widely recognized as powerful tools for heterogeneity analysis of longitudinal data sets. However, the existing research pays more attention to such as the variable selection, parameter estimation and dimension reduction on linear relationships with too many assumptions while nonlinear relationships are ubiquitous. In this paper, an extension fixed-effects model is proposed on the curve_fit nonlinear least squares. First, with the help of expert knowledge, the series regressions between independent variables including time and dependent variable is estimated on each series data, and the parameters are estimated by curve_fit. Similarly, the coeffection between independent variables including time and dependent variable is also initially estimated on the whole panel data. Second, the distance between regressions is defined, and then the coeffect function between the series regressions is obtained on the initial co-effect with curve_fit. Third, the time-effects and individual fixed-effects for each series data in the panel data are estimated on the differences of series regressions and co-effect function. Additionally, the effectiveness of the proposed method is varified on the synthetic data.

Acrylamide is probably carcinogenic to humans (International Agency for Research on Cancer, group 2A) with major occurrence in heated, mainly carbohydrate-rich foods. For roasted coffee, a European Union benchmark level of 400 µg/kg acrylamide is of importance. Regularly, the acrylamide contents are controlled using liquid chromatography combined with tandem mass spectrometry (LC-MS/MS). This reference method is reliable and precise but laborious because of the necessary sample clean-up procedure and instrument requirements. This research investigates the possibility of predicting the acrylamide content from proton nuclear magnetic resonance (NMR) spectra that are already recorded for other purposes of coffee control. In the NMR spectrum acrylamide is not directly quantifiable, so that the aim was to establish a correlation between the reference value and the corresponding NMR spectrum by means of a partial least squares (PLS) regression. Therefore, 40 commercially available coffee samples with already available LC-MS/MS data and NMR spectra were used as calibration data. To test the accuracy and robustness of the model and its limitations, 50 coffee samples with extreme roasting degrees and blends were additionally prepared as test set. The PLS model shows an applicability for the varieties C. arabica and C. canephora, which were medium to very dark roasted using drum or infrared roasters. The root mean square error of prediction (RMSEP) is 79 µg/kg acrylamide (n=32). The PLS model is judged as suitable to predict the acrylamide values of commercially available coffee samples. On the other hand, very light roasts containing more than 1000 µg/kg acrylamide are currently not suitable for PLS prediction.

The purpose of this paper is threefold: (i) to introduce and study the Euler-Lagrange prolongations of flatness PDEs solutions (best approximation of flatness) via associated least squares Lagrangian densities and integral functionals on Riemannian manifolds; (ii) to analyze some decomposable multivariate dynamics represented by Euler-Lagrange PDEs of least squares Lagrangians generated by flatness PDEs and Riemannian metrics; (iii) to give examples of explicit flat extremals and non-flat approximations.

Stroke often results in impaired gait, which can limit community ambulation and the quality of life. Recent works have shown the feasibility of transcranial Direct Current Stimulation (tDCS) as an adjuvant treatment to facilitate gait rehabilitation. Since the cerebellum plays an essential role in balance and movement coordination, which is crucial for independent overground ambulation, so, we investigated the effects of cerebellar tDCS (ctDCS) on the post-stroke overground gait performance in chronic stroke survivors. Fourteen chronic post-stroke male subjects were recruited based on convenience sampling at the collaborating hospitals where ten subjects finally participated in the ctDCS study. We evaluated the effects of two ctDCS montages with 2mA direct current, a) optimized configuration for dentate stimulation with 3.14cm² disc anode at PO10h (10/5 EEG system) and 3.14cm² disc cathode at PO9h (10/5 EEG system), and b) optimized configuration for leg lobules VII-IX stimulation with 3.14cm² disc anode at Exx8 (electrodes defined by ROAST) and 3.14cm² disc cathode at Exx7. We found ctDCS to be acceptable by all the exposed subjects. The ctDCS intervention had an effect on the 'Normalised Step length Affected side' (p=0.1) and 'Gait Stability Ratio' (p=0.0569), which was found using Wilcoxon signed-rank test at 10% significance level. Also, ctDCS montage specific effect was found using a two-sided Wilcoxon rank-sum test at a 5% significance level for 'Step Time Affected Leg' (p=0.0257) and '%Stance Time Unaffected Leg' (p=0.0376). Moreover, the changes in the quantitative gait parameters across both the montages were found to be correlated to the mean electric field strength in the lobules based on partial least squares regression analysis (R² statistic = 0.6574) where the mean electric field strength at the cerebellar lobules, Vermis VIIIb, Ipsilesional IX, Vermis IX, Ipsilesional X, had the most loading. In conclusion, our feasibility study indicated the potential of a single session of ctDCS to contribute to the immediate improvement in the balance and gait performance in terms of gait-related indices and clinical gait measures.

Although, staging models gained momentum to stage define affective disorders, no attempts were made to construct mathematical staging models using clinical and biomarker data in patients with major depression and bipolar disorder.The aims of this study were to use clinical and biomarker data to construct statistically-derived staging models, which are associated with early lifetime traumata (ELTs), affective phenomenology and biomarkers.In the current study, 172 subjects participated, 105 with affective disorders (both bipolar and unipolar) and 67 controls. Staging scores were computed by extracting latent vectors (LVs) from clinical data including ELTs, recurring flare ups and suicidal behaviors, outcome data such as disabilities and health-related quality of life (HR-QoL), and paraoxonase (PON)1 actvities and nitro-oxidative stress biomarkers.Recurrence of episodes and suicidal behaviors could reliably be combined into a LV with adequate composite reliability (the “recurrence LV”), which was associated with female sex, the combined effects of multiple ELTs, disabilities, HR-QoL and impairments in cognitive tests. All those factors could be combined into a reliable “ELT-staging LV” which was significantly associated with nitro-oxidative stress biomarkers. A reliable LV could be extracted from serum PON1 activities, recurrent flare ups, disabilities and HR-QoL.Our ELT-staging index scores the severity of a relevant affective dimension, shared by both major depression and bipolar disorder, namely the trajectory from ELTs, a relapsing course and suicidal behaviors to progressive disabilities. Patients were classified into three stages, namely an early stage; a relapse-regression stage; and a suicidal-regression stage. Lowered lipid-associated antioxidant defenses may be a drug target to prevent the transition from the early to the later regression stages.

In this paper, the optimal approximation algorithm is proposed to simplify non-linear functions and/or discrete data as piecewise polynomials by using the constrained least squares. In time-sensitive applications or in embedded systems with limited resources, the runtime of the approximate function is as crucial as its accuracy. The proposed algorithm search to find the Optimal Piecewise Polynomial (OPP) with minimum computational cost while ensuring the error below a specified threshold. This was accomplished by using smooth piecewise polynomials with optimal order and number of intervals. The computational cost only depends on polynomial complexity, i.e., the order and the number of intervals at runtime function call. For optimal approximation, computational costs for all the possible combinations of piecewise polynomials were calculated and tabulated as ascending order for the specific target CPU off-line. Each combination was optimized through constrained least squares and random selection method for given sample points. Afterward, whether the approximation error is below the predetermined value is examined. When the error is permissible, the combination is selected as the optimal approximation or the next combination was examined. To verify the performance, several representative functions were examined and analyzed.

Empirical equations representing, interpolating and smoothing groups of measurement results by regression methods are in widespread use in metrology and other fields of science and engineering. Standard equations for the propagation of measurement uncertainties to values computed from such equations are available but suffer from a lack of general acceptance and are only infrequently applied in practice. One reason for the slow uptake is the lack of clear methods to account for systematic error. In this paper, uncertainty propagation equations in terms of covariance matrices are generalized to allow for systematic errors in least-squares regression, and effects of the resulting uncertainties are investigated analytically. A stochastic ensemble model of systematic error is proposed for the computation of the non-diagonal elements of the weight matrix of the Generalized Least-Squares method (GLS) from the measurement uncertainty. A GLS projector formalism is described which separates the effects of measurement scatter on values calculated by the equation from those on the related “residuals”, i.e., the residual errors in the fitted data. The same projectors act similarly on the associated uncertainties and covariance matrices and permit the effects of systematic errors on the simulation covariance to be quantified. It is demonstrated that, in order to include systematic errors in the uncertainty estimates of GLS, covariance matrices may be substituted by novel, specifically defined dispersion matrices that are not specified yet by the GUM[1]. Systematic measurement errors may be estimated from various sources; a particularly easy way suggested here involves analyzing the structure in the regression residuals. It is demonstrated that GLS projectors exhibit inherent features of “error blindness” also with respect to systematic errors. [1] GUM: Guide to the Expression of Uncertainty in Measurement, http://www.bipm.org/en/publications/guides

Intelligent transportation systems (ITS) have recently evolved rapidly, which requires development of highly trustworthy and effective communication technologies for uses, including vehicle-to-vehicle (V2V) and vehicle-to-everything (V2X) communication; where Orthogonal Frequency Division Multiplexing (OFDM) is regarded as a strong candidate and highly popular option technique among these methods. However, the movement of vehicles introduces Doppler frequencies which produce inter-carrier interference (ICI), that is frequently occurs in V2X channels. This interference has the potential to compromise the integrity of subcarrier orthogonality within OFDM, leading to lower-quality communication and an increased likelihood of data transmission errors. When employing channels with doubly dispersive fading, OFDM necessitates the usage of a complex equalization based on the minimum mean-square error (MMSE) equalizer, which requires channel matrix inversion. Several low-complexity equalizers for OFDM have been developed and are based on band factorization, time domain LSQR (Least-Square QR) iterative computing, and banded minimum mean squared error (BMMSE). This paper proposes Conjugate Gradient Least Squares (CGLS), which is a novel iterative computation algorithm integrated with nonlinear equalizers. The suggested nonlinear equalization technique determines the trade-off between computations and performance. According to simulation data, the suggested nonlinear equalizer performs better than the current BMMSE and linear CGLS algorithms across doubly dispersive fading channels.

Dhaka one of the fastest-growing megacities in the world is increasingly vulnerable to urban flooding due to rapid urbanization, inadequate drainage infrastructure, and climate change-induced extreme weather events. This study presents the development of an urban flood forecasting system for Dhaka City using the MIKE+ hydrodynamic modeling software. The system integrates detailed hydrological and hydraulic models to simulate urban flooding scenarios, accounting for complex drainage networks and catchment characteristics. Real-time data from river gauges, rainfall stations, and drainage systems are incorporated to enhance the accuracy and reliability of the forecasts. The model's predictive capability is validated against historical flood events, demonstrating its effectiveness in forecasting flood extents, depths, and durations in critical areas of the city. This system serves as a valuable tool for city planners, emergency response teams, and decision-makers, enabling proactive flood management and risk mitigation. The study underscores the importance of such advanced modeling tools in safeguarding urban populations and infrastructures from the increasing threat of urban floods in Dhaka and similar rapidly urbanizing cities.

Spatial interpolation of meteorological data can have immense implications on risk management and climate change planning. Kriging with external drift (KED) is a spatial interpolation variant that uses auxiliary information in the estimation of target variable at unobserved locations. However, the traditional KED methods with linear trend functions may not be able to capture the complex and non-linear interdependence between target and auxiliary variables, which can lead to an inaccurate estimation. In this work, a novel KED method using least squares support vector regression (LSSVR) is proposed. This machine learning algorithm is employed to construct trend functions regardless of the type of variable interrelations being considered. To evaluate the efficiency of the proposed method (KED with LSSVR) relative to the traditional method (KED with a linear trend function), a systematic simulation study for estimating the monthly means temperature and pressure in Thailand in 2017 was conducted. The KED with LSSVR is shown to have superior performance over the KED with the linear trend function.

Introducing the Moving Least-Squares Aided Finite Element Method (MLS-FEM), we present a robust computational technique that effectively evaluates the development of mixing in polymeric mixing devices. Our approach uses the Moving Least-Squares (MLS) interpolant to enhance the classic finite element shape functions. As a result, it becomes possible to treat fixed or moving components, such as rotors of a mixer, as discontinuities within the flow domain. This allows analysis of the flow field with a background mesh independent of the rotors' shape, orientation, and position. We compared the MLS-FEM results with the classical boundary-fitted mesh FEM, which comprises the mesh regeneration steps by the movement of the rotors. We then showed that the new method provides accurate results for the flow field parameters (i.e., the velocity components and the pressure values) and the mixing evolution without requiring mesh regeneration and without compromising accuracy.

Reverse-order laws for generalized inverses of matrix products is a classic object of study in the theory of generalized inverses. One of the well-known reverse-order laws for a matrix product AB is (AB)^(i,...,j) = B^(i,...,j)A^(i,...,j), where (·)^i,...,j denotes an {i,...,j}-generalized inverse of matrix. Because {i,...,j}-generalized inverse of a general matrix is not necessarily unique, the relationships between both sides of the reverse-order law can be divided into four situations for consideration. In this article, we first introduce a linear mixed model y = ABβ + Aγ + ε, present two least-squares methodologies to estimate the fixed parameter vector  in the model, and describe the connections between the two least-squares estimators and the reverse-order laws for generalized inverses of the matrix product AB. We then prepare some valued matrix analysis tools, including a general theory on linear or nonlinear matrix identities, a group of expansion formulas for calculating ranks of block matrices, two groups of explicit formulas for calculating the maximum and minimum ranks of B^(i,...,j)A^(i,...,j), as well as necessary and sufficient conditions for B^(i,...,j)A^(i,...,j) to be invariant with respect to the choice of A^(i,...,j) and B^(i,...,j). We then present a unied approach to the 512 set inclusion problems {(AB)^(i,...,j) ⊇ {B^(i,...,j)A^(i,...,j)}for the eight commonly-used types of generalized inverses of A, B, and AB using the block matrix representation method (BMRM), matrix equation method (MEM), and matrix rank method (MRM), where {(·)^(i,...,j)} denotes the collection of all {i,...,j}-generalized inverse of a matrix.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

Partial least square (PLS) regression is a well-known chemometric method used for predictive modelling, especially in the presence of many variables. Although PLS was not initially developed as a technique for classification tasks, scientists have reportedly used this approach successfully for discrimination purposes. Whereas some non-supervised learning approaches including but not limited to PCA, and k-means clustering do well in identifying/understanding grouping and clustering patterns in multidimensional data, they are limited when the end target is discrimination, making PLS a preferable alternative. A total of fertilized 672 chicken egg hyperspectral imaging data, consisting of 336 white eggs and 336 brown eggs were used in this study. Hyperspectral images in the NIR region of 900-1700 nm wavelength range were captured prior to incubation on day 0 and on days 1-4 after incubation. Eggs were candled on incubation day 5 and broken out on day 10 to confirm fertility. While a total number of 312 and 314 eggs were found to be fertile in the brown and white egg batches respectively, total numbers of non-fertile eggs in the same set of batches were 23 and 21 respectively. Spectral information was extracted from a segmented region of interest (ROI) of each hyperspectral image and spectral transmission characteristics were obtained by averaging the spectral information. A moving-thresholding technique was implemented for discrimination based on PLS regression results on the calibration set. With true positive rates (TPR) of up to 100% obtained at selected threshold values of between 0.50-0.85 and on different days of incubation, the results indicated that the proposed PLS technique can accurately discriminate between fertile and non-fertile eggs. The adaptive PLS approach was thereby presented as suitable for handling hyperspectral imaging-based chicken egg fertility data

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

Empirical models for intensive or extensive margins of trade that relate measures of exports to firm characteristics are usually estimated by variants of (generalized) linear models. Usually, the firm characteristics that explain these export margins enter the empirical model in linear form, sometimes augmented by quadratic terms or higher order polynomials, or interaction terms, to take care or test for non-linear relationships. If these non-linear relationships do matter and if they are ignored in the specification of the empirical model this leads to biased results. Researchers, however, can never be sure that all possible non-linear relationships are taken care of in their chosen specifications. This note uses for the first time the Kernel-Regularized Least Squares (KRLS) estimator to deal with this issue in empirical models for margins of exports. KRLS is a machine learning method that learns the functional form from the data. Empirical examples show that it is easy to apply and works well. Therefore, it is considered as a useful addition to the box of tools of empirical trade economists.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

Lap joints were friction stir welded in AA 7075-T6 at 1320 rpm and using two welding speeds: 70 mm/min and 120 mm/min. The temperature profiles of the weld zone were registered during the process; furthermore, the microhardness, tensile strength, and microstructure of the joints produced were examined. This study brings new insights into the thermomechanical behavior of the material during the process. The peak temperature obtained with the lower welding speed (70 mm/min) is 10% higher than that obtained with the higher speed (120 mm/min). Moreover, a 5% increase in microhardness and a 6% increase in tensile strength were were observed increasing the welding speed. Addition-ally, the microstructure examination demonstrated that, by decreasing the welding speed, the larger interaction between the tool and the material results in a deeper stir zone due to the increased heat diffusion downwards to the material. This heat flow affects the thermal profile and influences the resulting mechanical properties of the welded joints.

The concept of green energy is now at the forefront of development discourse, with the United Nations Sustainable Development Goals (SDGs) 7, 11, and 12 all aimed at promoting green energy consumption to combat the three planetary crises: climate change, biodiversity loss, and pollution. Similarly, issues regarding Africa’s natural resource curse have caused a stir in the growth and development literature for some time now and there is no sign that it will die out. This study, the first of its kind, simultaneously assesses the impact of green energy consumption and Africa’s natural resources rents on economic growth by applying the Feasible Generalized Least Square (FGLS) estimator and the dynamic panel models of the Pooled Mean Group (PMG) and Mean Group (MG) estimators on data from 1990 to 2020 for 24 selected African countries. The results show that green energy consumption has a short-run growth-limiting effect and a long-run growth-enhancing effect in Africa. The study also found evidence of the natural resource curse phenomenon in Africa. The study, therefore, calls for the advancement and usage of green energy for both domestic and industrial production in Africa. The study further calls for a revamp in the global tax policy to curb illicit financial activities and strengthening institutional quality for transparency and accountability in the entire value chain of natural resource management in Africa.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

This paper investigates the energy dissipation level of a nonlinear vehicle suspension system. The suspension system is modelled as a mass-spring-damper system, which is designed using the output frequency response function (OFRF) method. This method enables the derivation of an explicit relationship, between the system output spectrum (or Performance metric) and the system nonlinear parameters of interest. The OFRF polynomial, of the energy dissipation level, was derived in terms of the nonlinear parameters of interest. The results obtained show that the OFRF model, of the energy dissipation level, could be used to estimate the amount of heat dissipated, for a set of design parameters. This has potentials of providing some insights, in the design of vibration-based energy harvesters, as some of the wasted heat energy could be converted to electrical energy.

The article deals with auxetic structures made on the basis of suitably connected rigid rotating squares (from Grima and Evans), with axes of rotation on the squares’ surface. The geometric model and the resulting relationships that allow for the determination of Poisson’s ratio are considered in detail. It is demonstrated that changing the rotation axis position does not affect the negative Poisson’s ratio, equal to -1. The models built confirm the initial considerations and can offer new application possibilities.

As matrix representations of magic labelings of related hypergraphs, magic squares and their various variants have been applied to many domains. Among various subclasses, trimagic squares have been investigated for over a hundred years. The existence problem for trimagic squares with singly even orders and orders 16n has been solved completely. However, very little is known for the existence of trimagic squares with other even orders except for the only three examples and three families. We construct normal trimagic squares by using product constructions, row-square magic rectangles, and trimagic pairs of orthogonal diagonal Latin squares. We give a new product construction: For positive integers p, q, and r having the same parity other than 1, 2, 3, 6, if normal p × q and r × q row-square magic rectangles exist, then a normal trimagic square with order pqr exists. As its application, we construct normal trimagic squares of orders 8q^3 and 8pqr for all odd integers q not less than 7 and p,r ∈ {7, 11, 13, 17, 19, 23, 29, 31, 37}. Our construction can easily be extended to construct multimagic squares.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

In the paper, the authors consider the generating functions of the Hermite polynomials and their squares, present explicit formulas for higher order derivatives of the generating functions of the Hermite polynomials and their squares, which can be viewed as ordinary differential equations or derivative polynomials, find differential equations that the generating functions of the Hermite polynomials and their squares satisfy, and derive explicit formulas and recurrence relations for the Hermite polynomials and their squares.

When wildlife and motor vehicles collide, the result for the animals is often death (roadkill). A commercial roadkill Virtual Fence (VF) mitigation device (iPTE Traffic Solutions) was used in a field trial to test its effectiveness along a 4.9-km segment of road on Bruny Island, Tasmania. A total of 585 days of monitoring of roadkill by species was conducted, with six sections alternatively switched on or off, according to a variation of a Crossover and Multiple Before-After-Control-Impact (MBACI) experimental designs that divided monitoring into “off-on” then “on-off” blocks of periods with each “on” period followed by a 16 d “wash-out” period. For the six sections over the four periods that exclude wash-outs, the 24 aggregated values of daily counts of roadkill of Tasmanian pademelons (Thylogale billardierii), that gave a total count of 222, were modelled. Other species were killed in insufficient numbers for analysis to be informative. The statistical analysis exploited the MBACI design to estimate the VF effect using a log-odds ratio parameter (LORP) while accounting for local spatio-temporal effects. Both versions of the analysis, either averaging over the three spatial replicates (paired sections) or two temporal replicates (blocks) gave no statistically significant effect of the VF judged as a LORP estimate not sufficiently below zero. Corresponding percentage reduction estimates of 9% and 16% were derived from the LORP estimates and given parameter uncertainty estimates the power to detect as significant a LORP corresponding to a 50% reduction in rate were 0.5 and 0.6, respectively. This study confirms results from a similar field trial carried out in 2018 also in southern Tasmania and adds to the evidence that this VF is likely to give if anything only a minor reduction in roadkill for a commonly killed species for which researchers have the best chance of detecting any practically useful reduction.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Partial Differential Equations (PDEs) constitute a fundamental framework for modeling various physical phenomena across diverse fields such as physics, engineering, and finance. Solving PDEs accurately and efficiently remains a significant challenge, particularly when dealing with complex systems or high-dimensional data. In this paper, we present a novel approach based on deep learning techniques to investigate the effective factors in solving PDEs. Our methodology leverages the expressive power of deep neural networks to learn and represent the underlying relationships between input parameters and the solutions of PDEs. By incorporating domain knowledge into the network architecture and training process, our approach aims to provide insights into the key factors influencing the solution of PDEs. We demonstrate the effectiveness of our method through numerical experiments on various PDEs, showcasing its capability to identify important features and improve predictive accuracy. Our findings suggest that deep learning techniques offer a promising avenue for understanding and analyzing the complex dynamics inherent in PDEs, paving the way for enhanced computational methods in scientific and engineering applications.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

This paper presents the results of investigations on the kinetic of Brilliant Blue FCF (BB) discoloration reactions in aqueous solutions with different ozone concentrations and pH conditions. Kinetic studies involve knowledge of the structure and properties of the dye and ozone, as well as the experimental conditions. In general, scientists admit that the predominant oxidation pathway is direct (by free oxygen atoms) or indirect (by free hydroxyl radicals), it will depend on influencing factors such as: the physicochemical properties of the dye, the pH of the aqueous solution, ozone concentration, reaction time and the contact mode with/without stirring. In the experimental research, two pathways were chosen following CBB = f(t): 1. constant dye concentration and different ozone concentration on the concentration range (100 - 250 mg/L) at three pH media (acidic, neutral and basic) with and without stirring; 2. Constant concentration of ozone and different dye in the range of concentrations (2.5 - 10 mg/L) under the conditions of point 1. With obtained experimental data the curves CBB = f(t) were drawn and were processed by the integral method of classical kinetic based on first and second order equations. Unfortunately, this simple procedure this not yield any minim full results and any pH level. The rate constants been negative and/or the reaction order been dependent on initial conditions. Due to its structure, the BB dye has several chromophore groups, thus multiple attack centers, resulting in more oxidation by-products, which is why the 1H - NMR spectrum of BB discoloration with ozone was recorded.

Rationale: Post-hepatectomy liver failure (PHLF) remains a significant risk for patients undergoing partial hepatectomy (PHx). Reliable prognostic markers and treatments to enhance liver regeneration are lacking. Plasma nanoparticles, including lipoproteins, exosomes, and extracellular vesicles (EVs), can reflect systemic and tissue-wide proteostasis and stress, potentially aiding liver regeneration. However, their role in PHLF is still unknow. Methods: Our study included 9 patients with hepatocellular carcinoma (HCC) undergoing PHx: 3 patients with PHLF, 3 patients undergoing the Associating Liver Partition and Portal vein Ligation for Staged hepatectomy (ALPPS) procedure and three matched controls without complications after PHx. Patient plasma was collected before (PRE), 1 and 5 days (POD1, POD5) after PHx. EVs were isolated by ultracentrifugation and extracted proteins subjected to quantitative mass spectrometry using a super-SILAC mix prepared from primary and cancer cell-lines. Results: We identified 2625 and quantified 2570 proteins in EVs in PHx patients. Among these, 53 proteins were significantly upregulated and 32 were downregulated in patients with PHLF compared to those without PHLF. Furthermore, 110 proteins were upregulated and 78 were downregulated in PHLF compared to patients undergoing ALPPS. The EV-proteomic signature in PHLF indicates significant disruptions in protein translation, proteostasis, intracellular vesicle biogenesis, as well as alterations in proteins involved in extracellular matrix (ECM) remodeling, metabolic and cell cycle pathways, present already before PHx. Conclusion: Longitudinal proteomic analysis of EV´s circulating in human patient plasma undergoing PHx uncovers proteomic signatures associated with PHLF which reflect dying hepatocytes and endothelial cells and are present before PHx already. Our results support EVs as potential biomarkers and therapeutic targets for liver regeneration and failure.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

Energy consumption modelling is of critical importance for improving energy efficiency in the drive towards sustainable manufacturing. Modern manufacturing processes and machine tools are very complex as they involve interplay of several advanced technologies. Therefore, energy modelling of modern machine tools is a complex multi-disciplinary task. This paper proposes a systematic and practical framework to choose the appropriate modelling approach for a given industrial problem. The framework was validated by applying it to diverse industrial scenarios.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

The optimization of photovoltaic (PV) systems is vital for enhancing efficiency and economic viability, especially under Partial Shading Conditions (PSCs). This study focuses on the development and comparison of traditional and advanced algorithms, including Perturb and Observe (P&O), Incremental Conductance (IC), Fuzzy Logic Control (FLC), Grey Wolf Optimization (GWO), Particle Swarm Optimization (PSO), and Artificial Neural Networks (ANN), for efficient Maximum Power Point Tracking (MPPT). Simulations conducted in MATLAB/SIMULINK evaluated these algorithms’ performance under various shading scenarios. The results indicate that while traditional methods like P&O and IC are effective under uniform conditions, advanced techniques, particularly ANN-based MPPT, exhibit superior efficiency and faster convergence under PSCs. The study concludes that integrating AI and ML into MPPT algorithms significantly enhances the reliability and efficiency of PV systems, paving the way for broader adoption of solar energy technologies in diverse environmental conditions. These findings contribute to advancing renewable energy technology and support the green energy transition.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

Nowadays, inquiries are one of the most important tasks to be executed in order to get valued information. When an inquiry is done to gather information about a human behavior there are some problems inherent to it. One of the main problems is how the information about many different persons can be processed to give good information about their environment. Most of the information gathered by these inquiries is used to analyze the behavior of the respondents. It can be used to estimate the success of a certain product on the market or just to validate the satisfaction of current costumers. The veracity of this information can be critical to model environments with some acceptable level of precision. Modelling environments through Artificial Neural Networks (ANN) is highly common because ANN’s are excellent to model predictable environments using a set of data. ANN’s are good in deal with sets of data with some noise, but they are fundamentally surjective mathematical functions and they aren’t able to give different results for the same input. So if an ANN is trained using data where the same input has different images which can be the case of survey data, this can be a problem for the success of modelling the environment. Therefore is necessary to process the data in order to adjust and eliminate invalid data.

In two previous articles, the extended $(k, t)$--Fibonacci numbers were presented and some of their properties were studied, both in general and particularizing them for the Leonardo numbers. In a second article we study the sum of the extended $(k, t)$--Fibonacci numbers as well as the sums of these odd and even numbers.\\ In this article we study the sum of the squares of these numbers with their properties as well as the generating function, the recurrence relation and the Binet formula.\\ Finally we particularize these results for the generalized $t$--Leonardo numbers.

In this paper, closed forms of the summation formulas for generalized Fibonacci numbers are presented. As special cases, we give summation formulas of Fibonacci, Lucas, Pell, Pell-Lucas, Jacobsthal, Jacobsthal-Lucas numbers.

We are witnessing a progressive divestment of some institutions with strong traditions and skills in physical modelling and their consequent impoverishment, to the detriment of numerical modelling. For many reasons, the economic imperatives and the exponential growth of computational means and numerical methods should certainly not be excluded. In this work, we aimed to highlight the new requirements of the recent sophisticated developments in physical modelling, precisely due to the new needs imposed on them by mathematical and numerical modelling and the growing risks in civil construction works. In this context, reflections are reported, justified by scientific and real-world examples, on the need for maintenance and reinforcement of investments in physical modelling, both to support the scientific community and to design buildings of significant economic, social and environmental impact.

Background: Intrauterine transfusion (IUT) of the donor and partial exchange (pET) of the recipient is a temporizing treatment for pregnancies with Twin Anemia Polycythemia Sequence (TAPS). We sought to give a detailed description of the procedural approach and outcomes for sequential donor IUT and recipient pET in TAPS. Methods: Retrospective study of spontaneous TAPS referred to the Johns Hopkins Center for Fetal Therapy treated with donor IUT followed by recipient pET utilizing a double-syringe set up. Procedure characteristics and outcomes as well as accuracy of existing transfusion formulas were analyzed and compared with the literature. Results: 5 of 78 patients with spontaneous TAPS underwent a total of 19 combined IUT/pET procedures (median first procedure to delivery interval 5.6 weeks [interquartile range IQR 1.9-6.0]). One pET was stopped for fetal decelerations. Patients delivered at 33.0 weeks [IQR 31.9-33.3] with two survivors and no neonatal transfusion requirements. IUT volumes were 48 ml [IQR 39-63 ml] and pET volumes 32 ml [IQR 20-50] utilizing aliquots of 5 – 20 mls for the latter (p=0.021). For IUTs, assumption of a fetal blood volume below 150 ml/kg underestimated required transfusion volume. For pETs, all formulas required adjustment of dilution volume based on bedside testing (p<0.05 for all). Conclusions: Donor transfusion followed by partial exchange in the recipient can prolong pregnancy in spontaneous TAPS and obviate the need for neonatal transfusion. A double-syringe setup facilitates efficient saline exchange. Because the accuracy of volume formulas is limited, bedside testing is recommended to achieve the target hemoglobin.

Group A rotaviruses (RVA) have been identified as the leading cause of neonatal calf diarrhea (NCD) In Yunnan, China, despite the limited documentation on this issue within the country. Given the significant impact on animal health and welfare, further attention is warranted to comprehend the prevalence and epidemiology of this disease. In this study, we isolated RVA strains from NCD clinical samples to support RVA epidemic study and further disease control in Yunnan. Material and Methods: Ten fecal samples were obtained from calves with a single episode of neonate calf diarrhea from a farmer during a severe NCD outbreak. For the diagnosis of Group A rotavirus (RVA) infection, fecal reverse transcription-polymerase chain reaction (RT-PCR) was employed as the primary method. Subsequently, RVA isolation was conducted on MA104 cells, with inoculates being pretreated with trypsin TPCK to enhance viral infectivity. The isolated RVA strain was further confirmed through RT-PCR and immunofluorescence assay. Results: RVA virus was isolated from clinical samples following six passages depended on trypsin treatment of inoculates. The sign of CPE detected consisted of increased cell granularity, obscure cell boundaries, cell rounding, and eventual degeneration and detachment of cells. Analysis of sequencing revealed that field isolates was of group A serotype. Phylogenetic analysis based on the ORF sequences of the VP4 and VP7 sequences segments indicated that the isolate was classified as the P[1] genotype. VP4 gene of strain YN-1 shares 75.2%-99.7% nucleotide identity of and 81.6%–99.7% amino acid identity with the complete VP4 sequences of the P[1]. The complete VP7 gene of YN-1 is 981 nucleotide long and encode 326 amino acids. The RotaC v2.0 analysis classified the sequence as the G8 genotype. The VP7 gene of strain YN-1 shares 88.5%-97.7% nucleotide identity and 94.2%-99.1% amino acid identity. Conclusion: This is the first study in China which reports the circulation of Group A NCD on cattle farms in the field. Our study constitutes a crucial and a necessary step allowing preventive and veterinary medicine to support RVA disease controls in Yunnan province, China.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

The research aims to present an innovative methodology to execute the Heritage conservation processes in a collaborative and interdisciplinary BIM project, with an effective management of the deterioration suffered over time, emphasizing the structures and coatings. The research begins with the architectural survey using scanning techniques (TLS) and terrestrial photogrammetry (SfM) and taking as a study the Duomo of Molfetta (Italy), a unique Romanesque architecture of Puglia (Italy). The methodological process is mainly aided by the precise semantic segmentation of global point clouds, a semi-automatic process assisted by classification algorithms implemented in the post-processing software, and which has allowed the classification of the unstructured information provided by the remote sensing equipment when identifying the architectural-structural systems of a building with high historical values. Subsequently, it has been possible to develop an efficient Scan-to-HBIM workflow, where the Heritage-BIM (HBIM) project has fulfilled the function of a database by incorporating and organizing all the information (graphic and non-graphic) to optimize the tasks of auscultation, identification, classification, quantification and, in turn, facilitating the parametric modeling of unique structures and architectural elements. The results have shown great effectiveness in the processes of characterization of architectural and artistic heritage, focusing on the deformations and deterioration of the masonry in columns, and making multidisciplinary conservation work in an HBIM project more flexible. But there are still some difficulties for the automatic interpretation of 3D point cloud data, related to specific systems of the historical architecture. In conclusion, human action and interpretation continues to be a fundamental pillar to achieve precise results in a heritage environment.

Schistosomiasis, acquired by skin-penetrating cercariae of dioecious digenean schistosomes during freshwater contact, afflicts nearly 260 and 440 million people with active infections and residual morbidity, respectively; about 10 million women at reproductive age contract schistosomiasis during gestation every year. Acute schistosomiasis is characterized by pre-patent pro-inflammatory CD4+ T-helper 1 or CD4+ Th1/T-helper 17 reactivity against immature schistosomulae. Chronic schistosomiasis is dominated by post-patent anti-inflammatory CD4+ T-helper 2 reactivity against ova epitopes; flukes co-exist in immunocompetent definitive hosts as they are capable of evading their defense mechanisms. Preventive measures should be complemented by vaccination, inducing long-term protection against transmission, infection, and disease recurrence, given the latest advancements in schistosomal vaccines. Transmission models incorporating vaccination available in PubMed, Embase and Web of Science up to December 31, 2023 are presented. Besides conceptual model differences, predictions meant to guide decision- and policymaking reveal continued worm harboring facilitating transmission besides residual infections, and increased susceptibility to re-infection and rebound morbidity, both shifted to later life stages following the intervention. Consequently, a vaccination schedule is pivotal considering the optimal age for initial immunization, i.e., pre-schoolchildren or schoolchildren, in a cohort-based or population-based manner while incorporating potential non-adherers promoting ongoing transmission; longevity over magnitude of vaccine protection to antigenic schistosomal moieties is crucial including accounting for existing pre-acquired immunity from natural exposure, in utero priming besides herd immunity, and induced by chemotherapy. Combining as one multi-component approach long-term effects of vaccination with short-term effects of chemotherapy as regular repeated vaccine-linked therapy in contrast to a single-component intervention seems most promising for achieving WHO’s endpoints of transmission elimination and morbidity control.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

The resilience of towns and cities refers to their ability to adapt and recover when confronted with pressures or challenges. This study employs ten variables as indicators to assess the resilience of urban areas by analyzing official data and constructing a multilevel mixed-effects structural equation model. The empirical findings demonstrate that enhancing resilience significantly influ-ences urban service functions, such as strengthening healthcare systems, stabilizing the real estate market, and addressing socio-economic challenges. Specifically, factors such as healthcare re-sources, housing demand, population structure, and social security exhibit varying levels of resil-ience, which profoundly impact the spatial distribution of these factors and socio-economic de-velopment. Disparities in healthcare resource allocation, demographic aging trends, and shifts in the housing market closely correlate with resilience levels in different regions. Additionally, the study emphasizes that improving resilience not only boosts the reliability and security of urban services but also ensures that communities receive necessary support and protection during times of adversity. Consequently, policymakers should recognize the pivotal role of urban resilience in resource allocation and social equity, devising corresponding strategies to enhance the resilience of these areas.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

Despite improvements in participation in population-based screening programs, colorectal cancer remains a major cause of cancer-related mortality worldwide. Targeted interventions are desirable to reduce the health and economic burden of this disease. Two-dimensional monolayers of colorectal cancer cell lines represent the traditional in vitro models for disease and are often used for diverse purposes, including delineation of molecular pathways associated with disease aetiology or to gauge drug efficacy. The lack of complexity in such models, chiefly the limited epithelial cell diversity and differentiation, attenuated mucus production, lack of microbial interactions and mechanical stresses, has driven interest in development of more holistic and physiologically relevant in vitro model systems. In particular, established ex vivo patient-derived explant and patient-derived tumour xenograft models have been supplemented by progress in organoid and microfluidic organ-on-a-chip cultures. Here we discuss the applicability of advanced culturing technologies, such as organoid systems, as models for colorectal cancer and for testing chemotherapeutic drug sensitivity and efficacy. We highlight current challenges associated with organoid technologies and discuss their future for more accurate disease modelling and personalized medicine.

Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.

Water footprint has been widely used to illustrate the consumption of water in many situations; for instance, in products, processes or regions of interest. In this work, we analyzed – using a sensitivity analysis approach – the effect of some variables in the calculation of the water footprint in the viticulture in Brazilian Serra Gaúcha (the major producing region of Brazilian Wine).The classical Penman-Monteith model for evapotransporation was considered, with uncertainties in some parameters (dead mulch covering fraction in the vineyard, maximum temperatures for some months, altitudes and latitudes of the site). The sensitivity analysis was conducted using the SAFE toolbox under Octave framework. The results indicated that the the portion of the water footprint corresponding to the evapotranspiration is more sensitive to the values of mulch covering fraction and the altitude of the site in comparison with the latitude and the maximum temperatures.

The following article analyzes Italian companies with more than 10 employees that use online sales tools. The data used were acquired from the ISTAT-BES database. The article first presents a static analysis of the data aimed at framing the phenomenon in the context of Italian regional disparities. Subsequently, a clustering with k-Means algorithm is proposed by comparing the Silhouette coefficient and the Elbow method. The investigation of the innovative and technological determinants of the observed variable is carried out through the application of a panel econometric model. Finally, different machine learning algorithms for prediction are compared. The results are critically discussed with economic policy suggestions.

Marine species are declining at an unprecedented rate, catalyzing many nations to adopt conservation and management targets within their jurisdictions. However, marine species and the biophysical processes that sustain them are naive to international borders. An understanding of the prevalence of cross-border species distributions is important for informing high-level conservation strategies, such as bilateral or regional agreements. Here, we examined 28,252 distribution maps to determine the number and locations of transboundary marine plants and animals. Over 90% of species have ranges spanning at least two jurisdictions, with 58% covering more than ten jurisdictions. All jurisdictions have at least one transboundary species, with the highest concentrations of transboundary species in the USA, Australia, Indonesia, and the Areas Beyond National Jurisdiction. Distributions of mapped biodiversity indicate that overcoming the challenges of multinational governance is critical for a much wider suite of species than migratory megavertebrates and commercially exploited fish stocks—the groups that have received the vast majority of multinational management attention. To effectively protect marine biodiversity, international governance mechanisms (particularly those related to the Convention on Biological Diversity, the Convention on Migratory Species, and Regional Seas Organizations) must be expanded to promote multinational conservation planning, and complimented by a holistic governance framework for biodiversity beyond national jurisdiction.

Sinonasal carcinomas are aggressive neoplasms that present a high morbidity and mortality rate with unfavorable prognosis. This group of tumors exhibits morphological and genetic diversity. Genetic and epigenetic alterations in these neoplasms are currently targets for diagnosis and treatment. The most common type of cancer originated in the sinonasal tract are sinonasal squa-mous cell carcinomas (SNSCC), which presents different histological patterns and variable his-tological aggressiveness. A significant number of alterations have been reported in sinonasal tu-mors, including deficiencies in the SwItch/Sucrose non-fermentable (SWI/SNF) chromatin remod-eling complex. In the sinonasal tract, deficiencies of the subunits SMARCB1/INI1, SMAR-CA4/BRG1 and SMARCA2 have been noted in carcinomas, adenocarcinomas, and soft tissue tu-mors with distinctive high-grade morphology and fatal prognosis. Objective: To identify the status of the SWI/SNF complex using immunohistochemistry in sinonasal squamous cell carci-nomas and its association with morphology and survival. Methods: A total of 1582 SNSCC cases were analyzed, selecting those with high-grade malignancy morphology, which were then evalu-ated immunohistochemically for SMARCB1 and SMARCA4 proteins. Their expression was compared with the biological behavior and survival of the patients. Results: Among the SNSCC, 47% corresponded to the non-keratinizing squamous cell carcinoma (NKSCC) type with high-grade characteristics, 40% were keratinizing squamous cell carcinomas (KSCC), 9% were SMARCB1-deficient carcinomas, and 4% were SMARCA4-deficient carcinomas. Mosaic expres-sion for SMARCB1 (NKSCC 33%, KSCC 21.9%) and SMARCA4 (NKSCC 14.6%, KSCC 12.2%) was identified, showing an impact on tumor size and progression. Conclusions: We identified that the mosaic expression of INI1 in NKSCC exhibited a worse prognosis compared to intact carcinomas and was similar to SMARCB1-deficent carcinoma.

This paper introduces a three-layer system, proposing a comprehensive model of granular mixture transport over a mobile sloped bed in a steady flow. This system, consisting of the bottom, contact and upper zones, provides complete, continuous sediment velocity and concentration vertical profiles. The model considers gravity’s effect on sediment transport in the bottom (dense) layer, a crucial factor often overlooked in previous studies. The induced movement in the mobile sublayer of the dense layer causes an increase in velocity at the upper boundary of this layer, significantly affecting the vertical distributions of velocity and concentration above this layer. We described the interactions between fractions and an intensive sediment mixing and sorting process in the contact layer. The proposed shear variation, with an increase in its maximum value at the bed, adds to the novelty of our approach. The data sets used for the model’s validation cover various conditions, including slopes, grain diameters, densities and grain mobility conditions, from incipient motion to a fully mobilised bed. This extensive validation process instils confidence in the theoretical description and its applicability to real-world scenarios.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

The extensive use of polypropylene (PP) in various industries has heightened interest in devel-oping efficient methods for recycling and optimising its mixtures. This study focuses on formu-lating predictive models for the Melt Flow Rate (MFR) and shear viscosity of PP blends. The in-vestigation involved characterising various grades, including virgin homopolymers, copolymers, and post-consumer recyclates, in accordance with ISO 1133 standards. The research examined both binary and ternary blends, utilising traditional mixing rules and symbolic regression to predict rheological properties. High accuracy was achieved with the Arrhenius and Cragoe models, at-taining R² values over 0.99. Symbolic regression further enhanced these models, offering signif-icant improvements. To mitigate overfitting, empirical noise and variable swapping were in-troduced, increasing the models' robustness and generalisability. The results demonstrated that the developed models could reliably predict MFR and shear viscosity, providing a valuable tool for improving the quality and consistency of PP mixtures. These advancements support the de-velopment of recycling technologies and sustainable practices in the polymer industry by opti-mising processing and enhancing the use of recycled materials.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.

Reservoirs created by damming rivers significantly modify the environment and problems may arise: the storage of nutrients and organic matter in reservoirs often leads to decreased water quality due to eutrophication. Reservoirs built on lowland rivers are exposed to significant nutrient loads, often leading to eutrophication. In this article, the Sulejów Reservoir, in Central Poland, was the subject of the research, which focused on the use of Sentinel-2 remote sensing data to detect phytoplankton blooms, and on understanding the pattern of wind-driven surface currents using the CCHE2D model (a depth-averaged hydrodynamic model). The calculation of the total phosphorus load has shown that the reservoir mainly acts as nutrient storage. Still, during the low flow and intensive phytoplankton bloom, it can be a source of nutrients. The distribution of phytoplankton bloom on the Sulejów Reservoir was documented using eight Sentinel-2 satellite images from the vegetation season of 2020 and the Normalized Difference Chlorophyll Index (NDCl). Coupling remote sensing data and numerical modelling helps to interpret the hydrodynamic model results and understand nutrients and sediment dynamics within the reservoir. Hydrodynamic modelling combined with remote sensing data can be a valuable tool for selecting appropriate locations for water quality measurements at monitoring stations.

In pediatric burn care, achieving swift healing with minimal complications remains paramount. This investigation assesses polyhexamethylene biguanide (PHMB)'s role in managing superficial partial-thickness burns in children, focusing on the effects of various patient-specific factors on recovery. Through a retrospective analysis of 27 pediatric cases treated with PHMB, we explored the impact of age, burn size, dressing frequency, treatment delay, cold therapy application, and analgesic usage on the duration until reepithelialization. Notably, the majority of patients benefited from early cold therapy, yet only 1 in 3 patients received analgesics. The study reveals a mean healing time of 8.78 days, with the extent of the burn showing a strong correlation to recovery speed. Most treatments were managed outpatient, evidenced by a negligible average hospital stay. Impressively, the intervention recorded no complications. Our findings endorse PHMB as a promising treatment for second-degree burns in young patients, offering healing efficiency on par with or surpassing traditional methods, without increasing complication risks. This investigation underscores the necessity for continued exploration into the optimal application of prehospital interventions and the comprehensive benefits of PHMB in pediatric burn management, advocating for future research aimed at assessing long-term outcomes, including scar quality and patient satisfaction.

Due to an urgent need for reducing the fast progressing climate changes, a rapid, standardized and replicable solution for the infrastructure restructuring of heat demand coverage of buildings at district and city level must be developed. As more and more communities in Europe, especially in Germany, are obligated to have plans for coverage of heat demand, city planners, energy agencies seek a tool, which will help them to design the first drafts of heating network routes, which can supply whole districts and cities with renewable energy. ArcGIS Pro Tools like Least-Cost-Path-Analysis (LCPA) and Closest Facility (CF) allow to find the shortest and “cheapest” way between the heat source and heat consumers in the analyzed areas. Starting from the community level, through the district, county, voivodeship and whole country levels, the replication of the methods for generating district heating (DH) network infrastructure can be achieved. The proposed LCPA and CF based methods help to design the most suitable and efficient DH networks in the analyzed areas. As only few open-source data input, like street networks and building footprints are needed, the methods can be implemented in all communities of the country of Poland. In this paper one example of one community of Wroclaw county, called Siechnice and surroundings is presented.

The objective of this study was to develop the least-cost starter’s diet and evaluated its effect on the growth performance of Sasso breeds and Indigenous ecotype of chicks under the local condition of the South Gondar Zone. The effects of substitution of different levels of commercial starters ration with homemade diet on the growth performance of Sasso and Indigenous chicks were studied in Hiruy Abaregay village of Farta district. The research area is 586km distant from the capital city of Addis Ababa, Ethiopia. A total of 510 Sasso T-44 and 90 Indigenous local ecotypes day-old chicks were randomly divided into five groups, each with 102 and 18 chicks, respectively. These were assigned into five treatments in which 100 (T1), 75 (T2), 50 (T3), 25 (T4), and 0% (T5) of commercial starter’s diet in factorial completely randomized design (CRD) with 3 replications for 60 days feeding period. The results obtained indicated that increased levels of substitution of a commercial diet with a homemade diet significantly depressed (p<0.001) mean daily feed consumption and retention of dry matter, nitrogen, and metabolizable energy. Growth rate as measured by mean daily weight gain, mean final body weight, and total feed consumption and feed cost were significantly miserable (p<0.001) in an increased homemade diet. On the contrary, there was an increase in feed conversion ratio and fiber content in high-level dilution of starter’s commercial diet with a homemade diet. However, the groups of chicks on 0, 25, and 50% commercial starters diets replaced by homemade diet were significantly higher (p<0.001) in mean daily feed intake, daily weight gain, feed conversion ratio, and final body weight attained. The results of this study indicated that up to 50% of expensive commercial starter’s diet could economically be replaced with the least cost homemade diet without adversely affecting the growth performance of chicks.

Human induced climate change led to the recognition of Community-Based Adaptation (CBA) as one of the remedies in building adaptive capacity and resilience of communities. It recognizes the resources and the skills as well as the agency of communities in shaping the optimal strategy. CBA interventions are vital in addressing community needs and contextual specificities, enable participatory and inclusive engagement and thereby facilitate more profound adaptation impacts. Agent-based modelling (ABM) harbors the potential to be the ideal tool to support developing of tailored adaptation strategies while considering capacities, resources, skills, priorities, needs and the cultural context of local communities. ABM allows to capture the complex relationships among various components within community decision making on CBA actions, the CBA actions themselves and the environment. There exist plenty of tools, however they provide for varying degrees of freedom in agent definition, sensitivity analysis, scalability, experiment design and output analysis to name a few. A set of required key criteria for CBA modelling is developed and all available ABM modelling and simulation tools are assessed for their suitability for CBA. NetLogo emerges as the most fitting tool for incorporating and handling the special features of CBA. It is closely followed by GAMA and Envision. The article provides insights and guidance to researchers and practitioners in selecting ABM tools aligned with the specific requirements of their CBA simulations and projects.

Sustainable water resource management in Bangladesh's Gumti River Basin faces challenges from climate change, urbanization, and population growth. This study aimed to calibrate and validate the HEC-HMS model for the Gumti River to enhance flood prediction and water resource planning. The model was set up using precipitation, temperature, and discharge data from 2019-2021, with SRTM elevation data for catchment delineation. Manual calibration was performed for 2019-2020, followed by validation for 2021, using parameters such as Muskingum routing and SCS Curve Number. Model performance was evaluated using R², Nash-Sutcliffe efficiency (NSE), RSR, and PBIAS metrics. Results showed satisfactory to good performance, with R² values of 0.64 and 0.68 for calibration and validation, respectively. NSE values were within the satisfactory range, while PBIAS indicated very good performance with slight underestimation. The study concludes that the calibrated HEC-HMS model provides a reliable tool for simulating the Gumti River's hydrology, though there's room for improvement. Integration with flood frequency analysis, water quality monitoring, and climate change projections is recommended for comprehensive water resource management, alongside the implementation of Sustainable Water Resource Management principles and community engagement strategies.

Industrial fires at facilities including waste management sites, warehouses, factories, chemical works and fuel storage depots are relatively frequent occurrences. Often, these fires occur adjacent to urban communities and result in ground-level airborne pollutant concentrations that are well above guideline values. Land, water, livestock and crops may also be contaminated by the emissions and by firefighting activities. Moreover, impacted communities tend to have a higher proportion of minority ethnic populations, individuals with underlying health vulnerabilities, as well as those of lower socio-economic status. Nevertheless, this is an aspect of air quality that is under-researched, and so this review aims to highlight the public health hazards associated with industrial fires and the need for an effective, coordinated, public health response. We also review the range of monitoring techniques that have been utilised in such fires and highlight the role of dispersion modelling in predicting plume trajectories and in estimating population exposure. We recommend establishing 1-h guideline values for particulate matter to facilitate timely public health interventions and we highlight the need to review regulatory and technical controls for sites prone to fires, particularly in the waste sector.

The partial information decomposition (PID) framework is concerned with decomposing the information that a set of random variables has with respect to a target variable into three types of components: redundant, synergistic, and unique. Classical information theory alone does not provide a unique way to decompose information in this manner and additional assumptions have to be made. Inspired by Kolchinsky's recent proposal for measures of intersection information, we introduce three new measures based on well-known partial orders between communication channels and study some of their properties.

Epithelial-mesenchymal transition (EMT) is a cellular biological process involved in migration of primary cancer cells to secondary sites facilitating metastasis. Besides, EMT also confers properties such as stemness, drug resistance and immune evasion which can aid a successful colonization at the distant site. EMT is not a binary process; recent evidence suggests that cells in partial EMT or hybrid E/M phenotype(s) can have enhanced stemness and drug resistance as compared to those undergoing a complete EMT. Moreover, partial EMT enables collective migration of cells as clusters of circulating tumor cells or emboli, further endorsing that cells in hybrid E/M phenotypes may be the ‘fittest’ for metastasis. Here, we review mechanisms and implications of hybrid E/M phenotypes, including their reported association with hypoxia. Hypoxia-driven activation of HIF-1α can drive EMT. In addition, cyclic hypoxia, as compared to acute or chronic hypoxia, shows the highest levels of active HIF-1α and can augment cancer aggressiveness to a greater extent, including enriching for a partial EMT phenotype. We also discuss how metastasis is influenced by hypoxia, partial EMT and collective cell migration, and call for a better understanding of interconnections among these mechanisms. We discuss the known regulators of hypoxia, hybrid EMT and collective cell migration and highlight the gaps which needs to be filled for connecting these three axes which will increase our understanding of dynamics of metastasis and help control it more effectively.

Reduction of the density operator for quantum subsystems is derived without the use of the Born Rule.

Partial sums of analytic univalent functions and partial sums of starlike have been investigated extensively by several researchers. In this paper, we investigate a partial sums of convex harmonic functions that are univalent and sense preserving in the open unit disk.

Elderly individuals frequently perceive companion robots devoid of warmth, resulting in a reluctance to accept these robots' services. This perception has become a significant barrier to the introduction of companion robots into households. To address this issue, this study employs KE methods to translate the elderly's need for warmth perception from companion robots into elements of modelling design. Initially, 20 pairs of affective words and 22 sample images of companion robots were chosen. The "rational-emotional" and "dim-bright" dimensions were identified as positively influencing the elderly's warmth perception of companion robots through SD method analysis. Subsequently, a hierarchical analysis table was established, with warmth perception as the root layer, modelling style and color matching as the basic layer, "rational-emotional" and "dim-bright" as the expansion layer, and the eight characteristic elements of companion robots as the morphological layer. The link between affective imagery and design elements was then established from the sample robots with higher warmth perception scores. Based on the correlation between the two, various design schemes were formed through random combinations. Finally, the design schemes were evaluated using the warmth perception scale, and the warmth perception scores of each sample model were obtained. This research provides design references for designing companion robots for the elderly with a "sense of warmth".

Problem solving is one of the most important components of the human cognition that affects for ages the progress of the human society. Mathematical modelling is a special type of problem solving concerning problems related to science or everyday life situations. The present study is a review of the author’s earlier works on problem solving and mathematical modelling from the scope of Education. Its real goal is that it presents in a systematic way and in a few pages only the results of many years research on the subject. This helps the reader to get a comprehensive idea about a very important topic belonging to the core of Mathematics Education, which is very useful to those wanting to study deeper the subject and get directions for further research in the area.

Small Shallow Lakes (SSL) support exceptionally high and original biodiversity, providing numerous ecosystem services. Their small size makes them especially sensitive to anthropic activities, that causes a shift to dysfunctional turbid states and induces loss of services and biodiversity. In this study we investigated the relationships between environmental factors and macrophyte communities. Macrophytes play a crucial role in maintaining functional clear states. Better understanding factors determining the composition and richness of aquatic plant communities in least-impacted conditions may be useful to protect them. We inventoried macrophyte communities and collected chemical, climatic and morphological data from 89 least-impacted SSL widely distributed in France. SSL were sampled across four climatic ecoregions, various geologies and elevations. Hierarchical cluster analysis showed a clear separation of four macrophyte assemblages strongly associated with mineralisation. Determinant factors identified by db-RDA analysis are, in order of importance, geology, distance from source (DIS, a proxy for connectivity with river hydrosystems), surface area, climate and hydroperiod (water permanency). Surprisingly, at country-wide scale, climate and hydroperiod filter macrophyte composition weakly. Geology and DIS are the major determinants of community composition, whereas surface area determines floristic richness. DIS is identified as determinant in freshwater lentic ecosystems for the first time.

Identification of recurrent driver mutations in genes encoding tyrosine kinases has resulted in the development of molecularly targeted strategies designed to improve the outcomes for patients diagnosed with acute myeloid leukemia (AML). The receptor tyrosine kinase FLT3, is the most commonly mutated gene in AML, with internal tandem duplications within the juxtamembrane domain (FLT3-ITD) or missense mutations in the tyrosine kinase domain (FLT3-TKD), present in 30%-35% of AML patients at diagnosis. An established driver mutation and marker of poor prognosis, the FLT3 tyrosine kinase has emerged as an attractive therapeutic target, and thus has encouraged the development of FLT3 tyrosine kinase inhibitors (TKIs). However, the therapeutic benefit of FLT3 inhibition, particularly as monotherapy, frequently results in the development of treatment resistance and disease relapse. Commonly, FLT3 inhibitor resistance is induced by the emergence of secondary lesions in the FLT3 gene, particularly in the second tyrosine kinase domain at residue Asp835 (D835) to form a ‘dual mutation’ (ITD-D835). Individual FLT3-ITD and FLT3-TKD mutations influence independent signaling cascades however, currently little is known which divergent signaling pathways are controlled by each of these FLT3 specific mutations, particularly in the context of patients harboring dual ITD-D835 mutations. This review provides a comprehensive analysis of the known discrete and cooperative signaling pathways regulated by each of the FLT3 specific mutations, as well as the therapeutic approaches that hold the most promise for development of more durable and personalized therapeutic approaches targeting mutant FLT3, to improve the treatment of AML.

Species distribution models (SDMs) are usually used to predict current species’ geographic distributions and to forecast the impact of climate change, with different aims, such as conservation, and biodiversity management. SDMs use has been increasing in the last decades, however, they are vulnerable to parametrization and data quality input. Thus, inappropriate input can lead to potential unreliability in results. In this context, the most used data and methodologies in SDM, and putative deviations from the consensual best practices, were identified, by analysing recent literature (2018 to 2022). Results show that the parameters presented more consistently are the chosen algorithm (MaxEnt was used in 98% of the studies), the accuracy measures, and the time windows. Many papers fail to specify other parameters, limiting the reproducibility of the studies. Some papers also fail to provide information about the target species: only a fraction of the species' range is considered, or no justification for including specific variables in the model is provided. These options can decrease reliability in predictions under future scenarios since data provided to the model is inaccurate from the start or there is insufficient information for outputs discussion.

The synchronous generator, as the main component of power systems, plays a key role in these system’s stability. Therefore, utilizing the most effective control strategy for modeling and control the synchronous generator results in the best outcomes in power systems’ performances. The advantage of using a powerful controller is to have the synchronous generator modeled and controlled as well as its main task i.e. stabilizing power systems. Since the synchronous generator is known as a complicated nonlinear system, modeling and control of it is a difficult task. This paper presents a sum of squares (SOS) approach to modeling and control the synchronous generator using polynomial fuzzy systems. This method as an efficacious control strategy has numerous superiorities to the well-known T–S fuzzy controller, due to the control framework is a polynomial fuzzy model, which is more general and effectual than the well-known T–S fuzzy model. In this case, a polynomial Lyapunov function is used for analyzing the stability of the polynomial fuzzy system. Then, the number of rules in a polynomial fuzzy model is less than in a T-S fuzzy model. Besides, derived stability conditions are represented in terms of the SOS approach, which can be numerically solved via the recently developed SOSTOOLS. This approach avoids the difficulty of solving LMI (Linear Matrix Inequality). The Effectiveness of the proposed control strategy is verified by using the third-part Matlab toolbox, SOSTOOLS.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Two-dimensional periodic Stokes flow of viscous incompressible fluid in a rectangular cavity with constant velocities applied to the top and bottom walls is considered. The study of chaotic advection regimes is reduced to the sequential solving of two problems. To solve the first problem, the analytical method of superposition, that allows to obtain any desired accuracy of the velocity field, is used. To solve the second problem, which is associated with obtaining the trajectories of individual fluid particles, numerical calculations of the Cauchy problem were performed. An analysis of the boundary conditions accuracy was performed based on the control of local integration. The advection of the selected volume of fluid in the rectangular cavity under the periodic motion of walls for a finite period time based on piecewise spline cubic interpolation is modelled. The obtained numerical results agree with well-known experimental data.

The main goal of this study was to evaluate sugarcane bagasse ash as a partial cement replacement material. Sugarcane bagasse ash is a by-product of fuel blending in the sugar industry. Yet all economic sugar is obtained after extraction from the cane. The disposal of the discharged waste in agriculture causes environmental problems in the sugar industry. The cement industry also creates environmental problems due to carbon dioxide emissions during cement manufacturing. Initially, bagasse ash samples were collected from the rubble of the Arjo Didessa sugar factory. The crude bagasse ash was sieved with a sieve size of 250µm. The strength of grade C-25 concrete was designed using five different concrete mixture proportions ranging from 5 to 20% cement by weight, including a water-cement ratio of 0.45. Impact strength tests were conducted at 7, 14, 21, and 28 days of age for each replacement ratio. For the experimental work, a total of 60 cubic concrete specimens were cast for compressive strength tests, and 15 cylindrical concrete specimens were cast for water absorption tests. Working compressive strength results indicated that bagasse ash could replace up to 5% of ordinary Portland cement concrete.

We propose a partial information decomposition based on the newly introduced framework of causal tensors, i.e., multilinear stochastic maps that transform source data into destination data. The innovation that causal tensors introduce is that the framework allows for an exact expression of an indirect association in terms of the constituting, direct associations. This is not possible when expressing associations only in measures like mutual information or transfer entropy. Instead of a priori expressing associations in terms of mutual information or transfer entropy, the a posteriori expression of associations in these terms results in an intuitive definition of a nonnegative and left monotonic redundancy, which also meets the identity property. Our proposed redundancy satisfies the three axioms introduced by Williams and Beer. Symmetry and self-redundancy axioms follow directly from our definition. The data processing inequality ensures that the monotonicity axiom is satisfied. Because causal tensors can describe both mutual information as transfer entropy, the partial information decomposition applies to both measures. Results show that the decomposition closely resembles the decomposition of other another approach that expresses associations in terms of mutual information a posteriori. A negative synergistic term could indicate that there is an unobserved common cause.

Historical city textures are living history embodying public open spaces of former civilizations, their landscapes and traditional life cultures, carrying them to the present and giving them life. The squares, which form the public open spaces, have been important meeting centers in the social lives of people. City furniture are the important elements in these public open spaces, reflecting the identity of the city and improving quality of life. City furniture improve the reflection of cultural value in historical city textures and their usability. The walled city center, where the historical city texture of Nicosia lies, has a very rich historical texture with the cultural heritage of various civilizations in the history of Cyprus. Public open spaces within the texture, which have acquired the quality of squares with their functions throughout the social history of Nicosia, are still important social spaces for the people of the city. This study analyzed Asmaaltı and Selimiye Squares, two important spaces of the walled city, through examining the city furniture in terms of their material, shape, and functionality, and their conformity with the historical texture. Their deficiencies and nonconformities with the historical texture were identified accordingly. In consideration with such examples, city furniture in historical city textures were assessed for their conformity with the texture characteristics, architectural styles, social, cultural, and economical characteristics, and relevant recommendations are presented respectively.

Tarihi kent dokuları, eski uygarlıkların kamusal açık alanlarını, peyzajlarını ve geleneksel yaşam kültürlerini bünyesinde barındıran, günümüze taşıyan ve yaşatan yaşayan bir tarihtir. Kamusal açık alanları oluşturan meydanlar, insanların sosyal yaşamlarında önemli buluşma merkezleri olmuştur. Kent mobilyaları bu kamusal açık alanlarda kentin kimliğini yansıtan ve yaşam kalitesini artıran önemli unsurlardır. Kent mobilyaları, kültürel değerlerin tarihi kent dokularına yansımasını ve kullanılabilirliğini artırır. Lefkoşa'nın tarihi kent dokusunun yattığı Suriçi kent merkezi, Kıbrıs tarihindeki çeşitli uygarlıkların kültürel mirası ile oldukça zengin bir tarihi dokuya sahiptir. Doku içinde kamusal açık alanlar, Lefkoşa'nın sosyal tarihi boyunca işlevleriyle meydan niteliği kazanan meydanlar, kent insanı için halen önemli sosyal mekanlardır. Bu çalışmada, Suriçi kentin iki önemli mekanı olan Asmaaltı ve Selimiye Meydanları, kent mobilyaları malzeme, biçim, işlevsellik ve tarihi dokuya uygunluk açısından incelenerek incelenmiştir. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur. kentliler için hala önemli sosyal mekanlardır. Bu çalışmada, Suriçi kentin iki önemli mekanı olan Asmaaltı ve Selimiye Meydanları, kent mobilyaları malzeme, biçim, işlevsellik ve tarihi dokuya uygunluk açısından incelenerek incelenmiştir. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur. kentliler için hala önemli sosyal mekanlardır. Bu çalışmada, Suriçi kentin iki önemli mekanı olan Asmaaltı ve Selimiye Meydanları, kent mobilyaları malzeme, biçim, işlevsellik ve tarihi dokuya uygunluk açısından incelenerek incelenmiştir. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur. ve tarihi dokuya uygunluğu. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur. ve tarihi dokuya uygunluğu. Buna göre eksiklikleri ve tarihi dokuya uymayanları tespit edilmiştir. Bu örnekler ışığında tarihi kent dokularındaki kent mobilyalarının doku özellikleri, mimari üsluplar, sosyal, kültürel ve ekonomik özelliklerle uygunluğu değerlendirilmiş ve öneriler sunulmuştur.

Lung cancer remains the most common cancer worldwide with a limited prognosis despite personalized treatment regimens. Low-dose computed tomography (CT) scanning as a means to early diagnosis has been disappointing due to the high false positive rate. Other non-invasive means of testing need to be developed that offer both timely diagnosis and predict prognosis. Methods: In the course of stool testing in a large-scale testing of 2,922 patients at increased risk of CRC we were able to ascertain 112 patients documented to have prospectively been diagnosed with lung cancer. Stool and colonic effluents were tested for p87 with anti-adenoma antibody (Adnab-9) reactivity by ELISA and western blot. Survival data were obtained where available. Results: Of 112 cancers, approximately 27.6% were squamous (SSC), 17.9% were adenocarcinoma, 8% small, 6.25% large cell and 3.57% were designated non-small cell cancer (NSCLC), 0.89% indeterminate, 0.89% lepidic spread (1), 3.57% had metastasis and in 31.25% data was unavailable. 49.1% of the lung cancer patients had fecal Adnab-9 testing. Overall, 60% had positive testing compared to 38%, which was significant (OR2.19[1/06-4.53];p=0.045). Cancers with higher lethality were less likely to test positive (approximately, 8.5% each for both small and large cell lung cancers), and higher, 56% with SCC and 25% for adenocarcinoma. 0% NSCLC). In the larger groups overall survival was worse in those testing positive: 474 testing positive versus 844 days in SCC and 54 testing positive versus 749 days in adenocarcinoma patients. Most importantly, the time from a positive test to the clinical diagnosis ranged from 2.72 years for small cell, 3.13 for adenocarcinoma, 5.07 for NSCLC, 6.07 for SSC, and 6.24 for large cell cancer. In excluded cases where cancer in the lung was believed to be metastatic,83.3% of cancers were positive. Conclusions: At a projected real-world sensitivity of 0.60 and specificity of 0.60 and the ability to predate diagnosis by up to 4.7 years overall, this test could help direct lung cancer screening. In addition, the Adnab-9 testing selectively detects worse tumor types (87.5%) and those with worse prognosis amongst the more common, favorable phenotypes thus making early diagnosis possible in those patients who stand to benefit most from this strategy. Metastatic lung cancer also detected by the test should be identified by the follow-up imaging studies and therefore would not be considered to be a major pitfall.

The increase in life expectancy, according to the World Health Organization, is a fact, and with it rises the incidence of age-related neurodegenerative diseases. The most recurrent symptoms are those associated with tremors resulting from Parkinson's Disease (PD) or Essential Tremors (ET). The main alternatives for the treatment of these patients are medication and surgical intervention, which sometimes have restrictions and side effects. Through computer simulations in Matlab software, this work investigates the performance of adaptive algorithms based on least mean squares (LMS) to suppress tremors in upper limbs, especially in the hands. The signals resulting from pathological hand tremors, related to PD, present components at frequencies that vary between 3~Hz and 6~Hz, with the more significant energy present in the fundamental and second harmonics, while physiological hand tremors, referred to as ET, vary between 4~Hz and 12~Hz. We simulated and used these signals as reference signals in adaptive algorithms, Filtered-x Least Mean Square (Fx-LMS), Filtered-x Normalized Least Mean Square (Fx-NLMS), and a hybrid Fx-LMS\&NLMS purpose. Our results showed that the vibration control provided by the Fx-LMS\&LMS algorithm is the most suitable for physiological tremors. For pathological tremors, we have used a proposed algorithm with a filtered sinusoidal input signal, Fsinx-LMS, which presented the best results in this specific case.

This paper is motivated by spatio-temporal pattern in the occurrence of Leishmaniasis in Afghanistan and the relatively high number of zero counts. We hold the view that correlations that arise from spatial and temporal sources are inherently distinct. Our method decouples these two sources of correlations, there are at least two advantages in taking this approach. First, it circumvents the need to inverting a large correlation matrix, which is a commonly encountered problem in spatio-temporal analyses. Second, it simplifies the modelling of complex relationships such as anisotropy, which would have been extremely difficult or impossible if spatio-temporal correlations were simultaneously considered. We identify three challenges in the modelling of a spatio-temporal process: (1) accommodation of covariances that arise from spatial and temporal sources; (2) choosing the correct covariance structure and (3) extending to situations where a covariance is not the natural measure of association. Moreover, because the data covers a period that overlaps with the US invasion of Afghanistan, the high number of zero counts may be the result of no disease incidence or lapse of data collection. To resolve this issue, a model truncated at zero built on a foundation of the generalized estimating equations was proposed.

The e-commerce sector is in a constant state of growth and evolution, particularly within its subdomain of online food delivery. As such, ensuring customer satisfaction is critical for companies working in this field. One way to achieve this is by providing accurate delivery time estimation. While companies can track couriers via GPS, they often lack real-time data on traffic and road conditions, complicating delivery time predictions. To address this, a range of statistical and machine learning techniques are being employed, including neural networks and specialized expert systems, with different degree of success. One issue with neural networks and machine learning models is their heavy dependence on vast, high quality data. To mitigate this issue we propose two Bayesian generalized linear models to predict time of the delivery. Utilizing a linear combination of predictor variables, we generate practical range of outputs with Hamiltonian Monte Carlo sampling method. These models offer a balance of generality and adaptability, allowing for tuning with expert knowledge. They were compared with PSIS-LOO and WAIC criteria. Results show that both models accurately estimated delivery times from the dataset, while maintaining numerical stability. Model with more predictor variables proved to be more accurate.

Human Papillomavirus (HPV) related cancers account for a large percentage of cancers. The tumor microenvironment (TME) is a complex structure and contributes significantly to tumor development, progression, and invasion. The TME is particularly pronounced in HPV-related cancers and HPV is known to influence the TME. In cancer research, there is an urgent need for new models to deepen our understanding of the pathophysiology of the disease and to facilitate the development of innovative therapies. In this context, 3D cell culture has emerged as a promising method in cancer research, that offers significant potential compared to conventional approaches. 3D modelling can produce results that are more consistent with clinical outcomes without the ethical concerns and problems of animal models. In this review, our aim is to discuss the tumor microenvironment in HPV-related cancers and demonstrate the importance of advancing 3D cell culture models for this purpose.

Introduction: The aim of the present systematic review was to evaluate the clinical and radiographic success of partial pulpotomies in deep caries processes or post-eruptive defects in young, vital permanent teeth. Methods: Electronic databases, PubMed, Scopus, and Embase, were searched, followed by a manual search. Randomized controlled trials evaluating partial pulpo-tomy with a follow-up period of ≥12 months were included. Meta-analyses using a random effect model were performed. Results: A total of 3.127 articles were retrieved, and after duplicate re-moval, 2.642 were screened by title and abstract; 1 additional article was found during the manual search in the reference lists, and 79 were identified. Finally, 6 papers were included in the review. Regardless of the partial pulpotomy modalities or material used, there were no signifi-cant differences between clinical and radiographic success rates (cumulative success rate 91,8%-92,3%, respectively). Five studies were included in the meta-analysis that did not indicate any statistically significant differences in success rates when Mineral Trioxide Aggregate was compared to other materials (95% CI 0,239 to 1,016 p=0.055). Conclusion: This research system-atically evaluates the evidence and summarises the available data on partial pulpotomy in young permanent teeth. Given its high clinical and radiographic success rate, partial pulpotomy should be considered when vital pulpal therapy needs to be performed in highly damaged young per-manent teeth, as this procedure provides a biological benefit and allows more invasive endodon-tic treatments to be postponed.

In this paper, the classical least square (CLS) method with molecular absorption spectrophotometric measurement was used to determine simultaneously of paracetamol (PAR), ibuprofen (IBU), and caffeine (CAF) in tablets. The absorbance spectra of the standard solutions and samples were measured over a wavelength from 220 to 300 nm with a 0.5 nm step. The concentration of PAR, IBU and CAF in the sample solutions were calculated by using a program called CLS-Excel written in Microsoft Excel 2016 and Visual Basic for Applications (VBA). The method and CLS-Excel program were tested on mixed standard laboratory samples with different PAR, IBU, and CAF concentration ratios, and they showed small errors and satisfying repeatability. An analytical procedure for tablets containing PAR, IBU, and CAF was developed. The reliability of the procedure was proved via the recovery and repeatability of the analysis results with an actual tablet sample and comparing the mean contents of active substances in the tablets obtained from the analytical procedure with the from the HPLC method. The procedure is simple with a reduced cost compared with the HPLC standard method.

The Totiviridae family of viruses has a unique genome consisting of double-stranded RNA with two open reading frames that encode the capsid protein (Cap) and the RNA-dependent RNA polymerase (RdRpol). Most virions in this family are isometric in shape, approximately 40 nm in diameter, and lack envelope. There are five genera within this family, including Totivirus, Victorivirus, Giardiavirus, Leishmaniavirus, and Trichomonasvirus. While Totivirus and Victorivirus primarily infect fungi, Giardiavirus, Leishmaniavirus, and Trichomonasvirus infect diverse hosts, including protists, insects, and vertebrates. Recently, new totivirus-like species have been discovered in fish and plant hosts, and through metagenomic analysis, a novel totivirus-like virus (named Tianjin totivirus) has been isolated from bat guano. Interestingly, Tianjin totivirus causes cytopathic effects in insect cells but cannot grow in mammalian cells, suggesting that it infects insects consumed by insectivorous bats. In this study, we used next-generation sequencing and identified totivirus-like viruses in liver tissue from Molossus molossus bats in the Amazon region of Brazil. Comparative phylogenetic analysis based on the RNA-dependent RNA polymerase region revealed that the viruses identified in Molossus bats belong to two distinct phylogenetic clades, possibly comprising different genera within the Totiviridae family. Notably, the mean similarity between Tianjin totivirus and the totiviruses identified in Molossus bats is less than 18%. These findings suggest that the diversity of totiviruses in bats is more extensive than previously recognized and highlight the potential for bats to serve as reservoirs for novel toti-like viruses.

Despite the clinical significance of partial posttraumatic stress disorder (PTSD), research on its associated cognitive function profiles is notably lacking. This study aimed to identify distinct cognitive function profiles in patients with partial PTSD. Medical records of Vietnamese War Korean Veterans undergoing psychiatric assessments, including the Clinician-Administered PTSD Scale (CAPS) and neurocognitive tests on the same day, were retrospectively reviewed. The participants were divided into partial PTSD (N = 10) and non-PTSD (N = 36) groups based on the CAPS interview. Neurocognitive test score profiles of the partial PTSD and non-PTSD groups were compared. Covariance analysis adjusted for potential confounders in cognitive function. In cognitive profiles, executive function, mental flexibility (measured by Trail Making Test B), and concentration (measured by the Mini-Mental Status Exam) were significantly poorer in the partial PTSD group. When adjusted for age, depressive symptoms, and education level, no significant differences were observed in the cognitive profiles between the partial PTSD and non-PTSD groups. In the current study, executive function and concentration showed deficits in patients with partial PTSD compared with those without PTSD. Partial PTSD cognitive profiles displayed no significant differences from non-PTSD profiles when adjusted for possible confounders such as depressive symptoms.

When we are asleep we lose the ability to promptly respond to external stimuli and yet we spend many hours every day in this inherently risky behavioral state. This simple fact strongly suggests that sleep must serve essential functions that rely on the brain going offline, on a daily basis, and for long periods of time. If these functions did not require partial sensory disconnection, it would be difficult to explain why they are not performed during waking. Paradoxically, despite its central role in defining sleep and what sleep does, sensory disconnection during sleep remains a mystery. We have a limited understanding of how it is implemented along the sensory pathways, we do not know whether the same mechanisms apply to all sensory modalities, nor do we know to which extent these mechanisms are shared between non-rapid eye movement (NREM) sleep and REM sleep. The main goal of this contribution is to review some knowns and unknowns about sensory disconnection during sleep as a first step to fill this gap.

The k-means is one of the most popular and widely used clustering algorithm, however, it is limited to only numeric data. The k-prototypes algorithm is one of the famous algorithms for dealing with both numeric and categorical data. However, there have been no studies to accelerate k-prototypes algorithm. In this paper, we propose a new fast k-prototypes algorithm that gives the same answer as original k-prototypes. The proposed algorithm avoids distance computations using partial distance computation. Our k-prototypes algorithm finds minimum distance without distance computations of all attributes between an object and a cluster center, which allows it to reduce time complexity. A partial distance computation uses a fact that a value of the maximum difference between two categorical attributes is 1 during distance computations. If data objects have m categorical attributes, maximum difference of categorical attributes between an object and a cluster center is m. Our algorithm first computes distance with only numeric attributes. If a difference of the minimum distance and the second smallest with numeric attributes is higher than m, we can find minimum distance between an object and a cluster center without distance computations of categorical attributes. The experimental shows proposed k-prototypes algorithm improves computational performance than original k-prototypes algorithm in our dataset.

In this study we discuss critical issues in modelling the structure and function of lymph nodes (LNs), with emphasis on how LN physiology is related to its multi-scale structural organization. In addition to macroscopic domains such as B-cell follicles and the T cell zone, there are vascular networks which play a key role in the delivery of information to the inner parts of the LN, i.e., the conduit and blood microvascular networks. We propose object-oriented computational algorithms to model the 3D geometry of the fibroblastic reticular cell (FRC) network and the microvasculature. Assuming that a conduit cylinder is densely packed with collagen fibers, the computational flow study predicted that the diffusion should be a dominating process in mass transport than convective flow. The geometry models are used to analyze the lymph flow properties through the conduit network in unperturbed- and damaged states of the LN. The analysis predicts that elimination of up to 60–90 % of edges is required to stop the lymph flux. This result suggests a high degree of functional robustness of the network.

This work presents a methodology for the generation and classification of phase resolved partial discharges (PRPD) patterns based on the use of a printed UHF monopole antenna and signal con-ditioning circuit to reduce hardware requirements. For this purpose, envelope detection technique was applied. In addition, test objects such as a hydrogenerator bar, dielectric disks with internal cavities in an oil cell, potential transformer, and tip-tip electrodes immersed in oil were used to generate partial discharge (PD) signals. To detect and classify partial discharges, the standard IEC 60270 (2000) method was used as reference. After acquisition of conditioned UHF signals, digital signal filtering threshold technique was used, and peaks of partial discharges envelopes pulses were extracted. Feature selection techniques were used to classify the discharges and choose the best features to train machine learning algorithms, such as multilayer perceptron, support vector ma-chine and decision tree. Accuracies greater than 84% were met, revealing the classification potential of the methodology proposed in this work.

The repeated application of herbicides has led to the development of herbicide resistance. Models are useful for identifying key processes and understanding the evolution of resistance. This study developed a spatially explicit model at a landscape scale to examine the dynamics of Lolium rigidum populations in dryland cereal crops and the evolution of herbicide resistance under var-ious management strategies. Resistance evolved rapidly under repeated herbicide use, driven by weed fecundity and herbicide efficacy. Although fitness costs associated with resistant plants re-duced resistance evolution, they did not affect the speed of spread. The most effective strategies to slow resistance involved diversifying cropping sequences (e.g., crop rotation) and the herbicide applications (e.g., rotating different herbicide modes of action). Pollen flow was the main disper-sal vector, with seed dispersal also contributing significantly. Strategies limiting seed dispersal effectively decreased resistance spread. However, the use of a seed-catching device at harvest could unintentionally enrich resistance in the area. It would be beneficial to optimise the move-ment of harvesters between fields. The model presented here is a useful tool that may assist in the exploration of novel management strategies within the context of site-specific weed management at the landscape scale, as well as in the advancement of our understanding of resistance dynamics.

Traumatic Brain Injury represents a significant public health concern due to its role in traumatic death and disability, often caused by head impacts or rapid accelerations. Despite advancements in Finite Element Head Models, existing models primarily represent adult males, neglecting anatomical and physiological differences between genders and age groups. Additionally, the mechanistic roles of specific intracranial tissues, such as the dura mater, have conventionally been overlooked. To better understand the mechanical behavior of the brain and its injured regions in the context of TBI, including the dura mater, this study proposes the development of a Female Finite Element Head Model. This model, representative of a middle-aged female subject, was developed using medical image-derived geometry and finite element modeling techniques. The validation results demonstrate a similarity between the numerical displacement curves and those obtained experimentally. In the model with dura mater, the numerical results show analogous behavior to the experimental results, despite minimal variations in the amplitude of the curves. These advancements highlight the significance of including the dura mater in biomechanical brain modeling. Incorporating the dura mater in Finite Element Head Models produces more realistic results than models without it. This emphasizes the importance of enhancing biomechanical models to better represent anatomical complexity.