Background: A large percentage of deaths in an epidemic or pandemic can be due to overshoot of population (herd) immunity, either from the initial peak or from planned or unplanned exit from lockdown or social distancing conditions. Objectives: We study partial unlock or reopening interaction with seasonal effects in a managed epidemic to quantify overshoot effects on small and large unlock steps and discover robust strategies for reducing overshoot. Methods: We simulate partial unlock of social distancing for epidemics over a range of replication factor, immunity duration and seasonality factor for strategies targeting immunity thresholds using overshoot optimization. Results: Seasonality change must be taken into account as one of the steps in an easing sequence, and a two step unlock, including seasonal effects, minimizes overshoot and deaths. It may cause undershoot, which causes rebounds and assists survival of the pathogen. Conclusions: Partial easing levels, even low levels for economic relief while waiting on a vaccine, have population immunity thresholds based on the reduced replication rates and may experience overshoot as well. We further find a two step strategy remains highly sensitive to variations in case ratio, replication factor, seasonality and timing. We demonstrate a three or more step strategy is more robust, and conclude that the best possible approach minimizes deaths under a range of likely actual conditions which include public response.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

Partial Differential Equations (PDEs) constitute a fundamental framework for modeling various physical phenomena across diverse fields such as physics, engineering, and finance. Solving PDEs accurately and efficiently remains a significant challenge, particularly when dealing with complex systems or high-dimensional data. In this paper, we present a novel approach based on deep learning techniques to investigate the effective factors in solving PDEs. Our methodology leverages the expressive power of deep neural networks to learn and represent the underlying relationships between input parameters and the solutions of PDEs. By incorporating domain knowledge into the network architecture and training process, our approach aims to provide insights into the key factors influencing the solution of PDEs. We demonstrate the effectiveness of our method through numerical experiments on various PDEs, showcasing its capability to identify important features and improve predictive accuracy. Our findings suggest that deep learning techniques offer a promising avenue for understanding and analyzing the complex dynamics inherent in PDEs, paving the way for enhanced computational methods in scientific and engineering applications.

CO₂ enhanced oil recovery (EOR) has been proven its capability to explore the unconventional tight oil reservoirs and potential for geological carbon storage. Meanwhile, the extremely low permeability pores exaggerate the difficulty CO₂ EOR and geological storage processing in the actual field. This paper initiates the ultrasonic-assisted approach to facilitate the oil-gas miscibility development and finally contribute to unlock more tight oils. First, the physical properties of crude oil with and without ultrasonic treatments were experimentally analysed through gas chromatography (GC), Fourier-transform infrared spectroscopy (FTIR) and viscometer. Second, the oil-gas minimum miscibility pressures (MMPs) were measured from the slim-tube test and the miscibility developments with and without ultrasonic treatments were interpreted from the mixing-cell method. Third, the nuclear-magnetic resonance (NMR) assisted coreflood tests were conducted to physically model the recovery process in porous media and directly obtain the recovery factor. Basically, the ultrasonic treatment (40KHz and 200W for 8 hours) was found to substantially change the oil properties, with viscosity (at 60°C) reduced from 4.1 to 2.8mPa·s, contents of resin and asphaltene decreased from 27.94% and 6.03% to 14.2% and 3.79%, respectively. The FTIR spectrum shows the unsaturated C-H bond, C-O bond and C≡C bond in macromolecules were broken from ultrasonic, which caused the macromolecules (e.g., resin and asphaltenes) to be decomposed into smaller carbon-number molecules. Accordingly, the MMP was determined to be reduced from 15.8 to 14.9MPa from the slim-tube test and the oil recovery factor increased by over 10%. This study reveals the mechanisms of ultrasonic-assisted CO₂ miscible EOR in producing tight oils.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

The optimization of photovoltaic (PV) systems is vital for enhancing efficiency and economic viability, especially under Partial Shading Conditions (PSCs). This study focuses on the development and comparison of traditional and advanced algorithms, including Perturb and Observe (P&O), Incremental Conductance (IC), Fuzzy Logic Control (FLC), Grey Wolf Optimization (GWO), Particle Swarm Optimization (PSO), and Artificial Neural Networks (ANN), for efficient Maximum Power Point Tracking (MPPT). Simulations conducted in MATLAB/SIMULINK evaluated these algorithms’ performance under various shading scenarios. The results indicate that while traditional methods like P&O and IC are effective under uniform conditions, advanced techniques, particularly ANN-based MPPT, exhibit superior efficiency and faster convergence under PSCs. The study concludes that integrating AI and ML into MPPT algorithms significantly enhances the reliability and efficiency of PV systems, paving the way for broader adoption of solar energy technologies in diverse environmental conditions. These findings contribute to advancing renewable energy technology and support the green energy transition.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

Background: Intrauterine transfusion (IUT) of the donor and partial exchange (pET) of the recipient is a temporizing treatment for pregnancies with Twin Anemia Polycythemia Sequence (TAPS). We sought to give a detailed description of the procedural approach and outcomes for sequential donor IUT and recipient pET in TAPS. Methods: Retrospective study of spontaneous TAPS referred to the Johns Hopkins Center for Fetal Therapy treated with donor IUT followed by recipient pET utilizing a double-syringe set up. Procedure characteristics and outcomes as well as accuracy of existing transfusion formulas were analyzed and compared with the literature. Results: 5 of 78 patients with spontaneous TAPS underwent a total of 19 combined IUT/pET procedures (median first procedure to delivery interval 5.6 weeks [interquartile range IQR 1.9-6.0]). One pET was stopped for fetal decelerations. Patients delivered at 33.0 weeks [IQR 31.9-33.3] with two survivors and no neonatal transfusion requirements. IUT volumes were 48 ml [IQR 39-63 ml] and pET volumes 32 ml [IQR 20-50] utilizing aliquots of 5 – 20 mls for the latter (p=0.021). For IUTs, assumption of a fetal blood volume below 150 ml/kg underestimated required transfusion volume. For pETs, all formulas required adjustment of dilution volume based on bedside testing (p<0.05 for all). Conclusions: Donor transfusion followed by partial exchange in the recipient can prolong pregnancy in spontaneous TAPS and obviate the need for neonatal transfusion. A double-syringe setup facilitates efficient saline exchange. Because the accuracy of volume formulas is limited, bedside testing is recommended to achieve the target hemoglobin.

Group A rotaviruses (RVA) have been identified as the leading cause of neonatal calf diarrhea (NCD) In Yunnan, China, despite the limited documentation on this issue within the country. Given the significant impact on animal health and welfare, further attention is warranted to comprehend the prevalence and epidemiology of this disease. In this study, we isolated RVA strains from NCD clinical samples to support RVA epidemic study and further disease control in Yunnan. Material and Methods: Ten fecal samples were obtained from calves with a single episode of neonate calf diarrhea from a farmer during a severe NCD outbreak. For the diagnosis of Group A rotavirus (RVA) infection, fecal reverse transcription-polymerase chain reaction (RT-PCR) was employed as the primary method. Subsequently, RVA isolation was conducted on MA104 cells, with inoculates being pretreated with trypsin TPCK to enhance viral infectivity. The isolated RVA strain was further confirmed through RT-PCR and immunofluorescence assay. Results: RVA virus was isolated from clinical samples following six passages depended on trypsin treatment of inoculates. The sign of CPE detected consisted of increased cell granularity, obscure cell boundaries, cell rounding, and eventual degeneration and detachment of cells. Analysis of sequencing revealed that field isolates was of group A serotype. Phylogenetic analysis based on the ORF sequences of the VP4 and VP7 sequences segments indicated that the isolate was classified as the P[1] genotype. VP4 gene of strain YN-1 shares 75.2%-99.7% nucleotide identity of and 81.6%–99.7% amino acid identity with the complete VP4 sequences of the P[1]. The complete VP7 gene of YN-1 is 981 nucleotide long and encode 326 amino acids. The RotaC v2.0 analysis classified the sequence as the G8 genotype. The VP7 gene of strain YN-1 shares 88.5%-97.7% nucleotide identity and 94.2%-99.1% amino acid identity. Conclusion: This is the first study in China which reports the circulation of Group A NCD on cattle farms in the field. Our study constitutes a crucial and a necessary step allowing preventive and veterinary medicine to support RVA disease controls in Yunnan province, China.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.

In pediatric burn care, achieving swift healing with minimal complications remains paramount. This investigation assesses polyhexamethylene biguanide (PHMB)'s role in managing superficial partial-thickness burns in children, focusing on the effects of various patient-specific factors on recovery. Through a retrospective analysis of 27 pediatric cases treated with PHMB, we explored the impact of age, burn size, dressing frequency, treatment delay, cold therapy application, and analgesic usage on the duration until reepithelialization. Notably, the majority of patients benefited from early cold therapy, yet only 1 in 3 patients received analgesics. The study reveals a mean healing time of 8.78 days, with the extent of the burn showing a strong correlation to recovery speed. Most treatments were managed outpatient, evidenced by a negligible average hospital stay. Impressively, the intervention recorded no complications. Our findings endorse PHMB as a promising treatment for second-degree burns in young patients, offering healing efficiency on par with or surpassing traditional methods, without increasing complication risks. This investigation underscores the necessity for continued exploration into the optimal application of prehospital interventions and the comprehensive benefits of PHMB in pediatric burn management, advocating for future research aimed at assessing long-term outcomes, including scar quality and patient satisfaction.

The partial information decomposition (PID) framework is concerned with decomposing the information that a set of random variables has with respect to a target variable into three types of components: redundant, synergistic, and unique. Classical information theory alone does not provide a unique way to decompose information in this manner and additional assumptions have to be made. Inspired by Kolchinsky's recent proposal for measures of intersection information, we introduce three new measures based on well-known partial orders between communication channels and study some of their properties.

Epithelial-mesenchymal transition (EMT) is a cellular biological process involved in migration of primary cancer cells to secondary sites facilitating metastasis. Besides, EMT also confers properties such as stemness, drug resistance and immune evasion which can aid a successful colonization at the distant site. EMT is not a binary process; recent evidence suggests that cells in partial EMT or hybrid E/M phenotype(s) can have enhanced stemness and drug resistance as compared to those undergoing a complete EMT. Moreover, partial EMT enables collective migration of cells as clusters of circulating tumor cells or emboli, further endorsing that cells in hybrid E/M phenotypes may be the ‘fittest’ for metastasis. Here, we review mechanisms and implications of hybrid E/M phenotypes, including their reported association with hypoxia. Hypoxia-driven activation of HIF-1α can drive EMT. In addition, cyclic hypoxia, as compared to acute or chronic hypoxia, shows the highest levels of active HIF-1α and can augment cancer aggressiveness to a greater extent, including enriching for a partial EMT phenotype. We also discuss how metastasis is influenced by hypoxia, partial EMT and collective cell migration, and call for a better understanding of interconnections among these mechanisms. We discuss the known regulators of hypoxia, hybrid EMT and collective cell migration and highlight the gaps which needs to be filled for connecting these three axes which will increase our understanding of dynamics of metastasis and help control it more effectively.

Partial sums of analytic univalent functions and partial sums of starlike have been investigated extensively by several researchers. In this paper, we investigate a partial sums of convex harmonic functions that are univalent and sense preserving in the open unit disk.

In 1982, MIT physicist Frank Wilczek predicted and named ANYONS, quasiparticles (particle-like formations) that are confined to 2 dimensions and were discovered in 2020. The name might come from Prof. Wilczek's lighthearted comment "anything goes". This article's main goal is to show that anyons could be another name for 1) virtual particles, 2) Mobius strips, and 3) figure-8 Klein bottles. Along the way, we'll see the picture painted by the article confirm that Einstein's dream of gravitational-electromagnetic unity fits in with anyons being Mobius strips. The topological hypothesis offers an explanation of dark matter and dark energy. We'll also have encounters with intergalactic travel and imaginary computers. They really could exist but are imaginary in the sense that they use imaginary time (as well as space-time warping).

The main goal of this study was to evaluate sugarcane bagasse ash as a partial cement replacement material. Sugarcane bagasse ash is a by-product of fuel blending in the sugar industry. Yet all economic sugar is obtained after extraction from the cane. The disposal of the discharged waste in agriculture causes environmental problems in the sugar industry. The cement industry also creates environmental problems due to carbon dioxide emissions during cement manufacturing. Initially, bagasse ash samples were collected from the rubble of the Arjo Didessa sugar factory. The crude bagasse ash was sieved with a sieve size of 250µm. The strength of grade C-25 concrete was designed using five different concrete mixture proportions ranging from 5 to 20% cement by weight, including a water-cement ratio of 0.45. Impact strength tests were conducted at 7, 14, 21, and 28 days of age for each replacement ratio. For the experimental work, a total of 60 cubic concrete specimens were cast for compressive strength tests, and 15 cylindrical concrete specimens were cast for water absorption tests. Working compressive strength results indicated that bagasse ash could replace up to 5% of ordinary Portland cement concrete.

We propose a partial information decomposition based on the newly introduced framework of causal tensors, i.e., multilinear stochastic maps that transform source data into destination data. The innovation that causal tensors introduce is that the framework allows for an exact expression of an indirect association in terms of the constituting, direct associations. This is not possible when expressing associations only in measures like mutual information or transfer entropy. Instead of a priori expressing associations in terms of mutual information or transfer entropy, the a posteriori expression of associations in these terms results in an intuitive definition of a nonnegative and left monotonic redundancy, which also meets the identity property. Our proposed redundancy satisfies the three axioms introduced by Williams and Beer. Symmetry and self-redundancy axioms follow directly from our definition. The data processing inequality ensures that the monotonicity axiom is satisfied. Because causal tensors can describe both mutual information as transfer entropy, the partial information decomposition applies to both measures. Results show that the decomposition closely resembles the decomposition of other another approach that expresses associations in terms of mutual information a posteriori. A negative synergistic term could indicate that there is an unobserved common cause.

Introduction: The aim of the present systematic review was to evaluate the clinical and radiographic success of partial pulpotomies in deep caries processes or post-eruptive defects in young, vital permanent teeth. Methods: Electronic databases, PubMed, Scopus, and Embase, were searched, followed by a manual search. Randomized controlled trials evaluating partial pulpo-tomy with a follow-up period of ≥12 months were included. Meta-analyses using a random effect model were performed. Results: A total of 3.127 articles were retrieved, and after duplicate re-moval, 2.642 were screened by title and abstract; 1 additional article was found during the manual search in the reference lists, and 79 were identified. Finally, 6 papers were included in the review. Regardless of the partial pulpotomy modalities or material used, there were no signifi-cant differences between clinical and radiographic success rates (cumulative success rate 91,8%-92,3%, respectively). Five studies were included in the meta-analysis that did not indicate any statistically significant differences in success rates when Mineral Trioxide Aggregate was compared to other materials (95% CI 0,239 to 1,016 p=0.055). Conclusion: This research system-atically evaluates the evidence and summarises the available data on partial pulpotomy in young permanent teeth. Given its high clinical and radiographic success rate, partial pulpotomy should be considered when vital pulpal therapy needs to be performed in highly damaged young per-manent teeth, as this procedure provides a biological benefit and allows more invasive endodon-tic treatments to be postponed.

This work presents a methodology for the generation and classification of phase resolved partial discharges (PRPD) patterns based on the use of a printed UHF monopole antenna and signal con-ditioning circuit to reduce hardware requirements. For this purpose, envelope detection technique was applied. In addition, test objects such as a hydrogenerator bar, dielectric disks with internal cavities in an oil cell, potential transformer, and tip-tip electrodes immersed in oil were used to generate partial discharge (PD) signals. To detect and classify partial discharges, the standard IEC 60270 (2000) method was used as reference. After acquisition of conditioned UHF signals, digital signal filtering threshold technique was used, and peaks of partial discharges envelopes pulses were extracted. Feature selection techniques were used to classify the discharges and choose the best features to train machine learning algorithms, such as multilayer perceptron, support vector ma-chine and decision tree. Accuracies greater than 84% were met, revealing the classification potential of the methodology proposed in this work.

Despite the clinical significance of partial posttraumatic stress disorder (PTSD), research on its associated cognitive function profiles is notably lacking. This study aimed to identify distinct cognitive function profiles in patients with partial PTSD. Medical records of Vietnamese War Korean Veterans undergoing psychiatric assessments, including the Clinician-Administered PTSD Scale (CAPS) and neurocognitive tests on the same day, were retrospectively reviewed. The participants were divided into partial PTSD (N = 10) and non-PTSD (N = 36) groups based on the CAPS interview. Neurocognitive test score profiles of the partial PTSD and non-PTSD groups were compared. Covariance analysis adjusted for potential confounders in cognitive function. In cognitive profiles, executive function, mental flexibility (measured by Trail Making Test B), and concentration (measured by the Mini-Mental Status Exam) were significantly poorer in the partial PTSD group. When adjusted for age, depressive symptoms, and education level, no significant differences were observed in the cognitive profiles between the partial PTSD and non-PTSD groups. In the current study, executive function and concentration showed deficits in patients with partial PTSD compared with those without PTSD. Partial PTSD cognitive profiles displayed no significant differences from non-PTSD profiles when adjusted for possible confounders such as depressive symptoms.

When we are asleep we lose the ability to promptly respond to external stimuli and yet we spend many hours every day in this inherently risky behavioral state. This simple fact strongly suggests that sleep must serve essential functions that rely on the brain going offline, on a daily basis, and for long periods of time. If these functions did not require partial sensory disconnection, it would be difficult to explain why they are not performed during waking. Paradoxically, despite its central role in defining sleep and what sleep does, sensory disconnection during sleep remains a mystery. We have a limited understanding of how it is implemented along the sensory pathways, we do not know whether the same mechanisms apply to all sensory modalities, nor do we know to which extent these mechanisms are shared between non-rapid eye movement (NREM) sleep and REM sleep. The main goal of this contribution is to review some knowns and unknowns about sensory disconnection during sleep as a first step to fill this gap.

The k-means is one of the most popular and widely used clustering algorithm, however, it is limited to only numeric data. The k-prototypes algorithm is one of the famous algorithms for dealing with both numeric and categorical data. However, there have been no studies to accelerate k-prototypes algorithm. In this paper, we propose a new fast k-prototypes algorithm that gives the same answer as original k-prototypes. The proposed algorithm avoids distance computations using partial distance computation. Our k-prototypes algorithm finds minimum distance without distance computations of all attributes between an object and a cluster center, which allows it to reduce time complexity. A partial distance computation uses a fact that a value of the maximum difference between two categorical attributes is 1 during distance computations. If data objects have m categorical attributes, maximum difference of categorical attributes between an object and a cluster center is m. Our algorithm first computes distance with only numeric attributes. If a difference of the minimum distance and the second smallest with numeric attributes is higher than m, we can find minimum distance between an object and a cluster center without distance computations of categorical attributes. The experimental shows proposed k-prototypes algorithm improves computational performance than original k-prototypes algorithm in our dataset.

We generalize the concept of a fuzzy metric by introducing its approximating counterpart in order to make it more appropriate for the study of some problems related to words combinatorics. We establish close relations between fuzzy approximating metrics in case of special $t$-norms and approximating parametrized metrics, discuss some relations between fuzzy approximating metrics and fuzzy partial metrics as well as show some possible applications of approximating parametrized metrics in the problems of words combinatorics.

Detection of partial discharge (PD) activities in high-voltage equipment can be done according to the several mechanisms of signal detection, which are electromagnetic wave signal detection, acoustic signal detection, chemical reactions, electrical signal detection, or optical emission detection. Recently, multiple methods of detection and localization of partial discharge activities occurred in power transformers and gas-insulated switchgear (GIS) have been proposed to monitor the health condition of high-voltage equipment, especially when the awareness regarding preventive maintenance has been emphasized at the industrial level and electrical providers. In aligning the needs of industrial and the improvement of PD detection methods, this manuscript focused on reviewing the current practice methods for the detection and localization of PD signals in high-voltage equipment and comparing their efficacy, in summarizing the future direction of research work-related methods of PD detection. The comparative reviews are discussed in terms of the mechanism of PD signal detection, indication parameters, calibration technique, advantages, and limitations of each method of PD measurement in detail.

Partial differential equations (PDEs) are used to describe a wide range of phenomena, such as heat transfer, fluid dynamics, and quantum mechanics. By solving PDEs, we can ob- tain insights into the behavior of the system and make predictions about its future evolution. Conventional numerical methods for obtaining the approximate solutions of PDEs may re- quire extensive computational resources and time, especially for complex PDEs and large- scale problems. The recently developed physics-informed neural network (PINN) has shown promise in a variety of scientific and engineering fields by incorporating physical laws into the loss functions of the neural network (NN). In addition, the training of PINN does not require ground truth data, but it has poor generalization ability to unseen domains. On the other hand, a convolutional neural network (CNN) has fast inference and better generalization ability, but it requires a large amount of training data. Taking the advantages of PINN and CNN by using Legendre multiwavelets (LMWs) as basis functions, we introduce a new method to approach the PDEs in this paper, namely Physics-Informed Legendre Multiwavelets CNN (PiLMWs-CNN), in order to continuously approximate a grid-based state representation that can be handled by a CNN. PiLMWs-CNN enable us to train our models using only physics-informed loss functions without any pre- computed training data, simultaneously providing fast and continuous solutions that gener- alize to previously unknown domains. In particular, the LMWs can simultaneously possess compact support, orthogonality, symmetry, high smoothness, and high approximation order. Compared to orthonormal polynomial (OP) bases, the approximation accuracy can be greatly increased and computation costs can be significantly reduced by using LMWs. We applied PiLMWs-CNN to approximate the damped wave equation, incompressible Navier-Stokes (N- S) equation, and two-dimensional heat conduction equation. The experimental results show that this method provides more accurate, efficient, and fast convergence with better stability when approximating the solution of PDEs.

The most common source of transformer failure is in the insulation, and the most prevalent warning signal for insulation weakness is partial discharge (PD). Locating positons of these partial discharges would help repair the transformer to prevent failures. This work investigates algorithms that could be deployed to locate the position of a PD event using data from ultra-high frequency (UHF) sensors inside the transformer. These algorithms typically proceed in two steps: first determine the signal arrival time and then locate the position based on time differences. This paper reviews available methods for each task and then propose new algorithms: a convolutional iterative filter with thresholding (CIFT) to determine the signal arrival time and a reference table of travel times to resolve the source location. The effectiveness of these algorithms are tested with a set of laboratory-triggered PD events and two sets of simulated PD events inside transfers in production use. Tests show the new approach provides more accurate locations than the best-known data analysis algorithms, and the difference is particularly large, 3.7X, when the signal sources are far from sensors.

Background: In the functional data analysis (FDA), the hybrid or mixed data are scalar and functional datasets. The semi-functional partial linear regression model (SFPLR) is one of the first semiparametric models for the scalar response with hybrid covariates. Various extensions of this model are explored and summarized. Methods: Two first research articles, including “semi-functional partial linear regression model”, and “Partial functional linear regression” have more than 300 citations in Google Scholar. Finally, only 106 articles remained according to the inclusion and exclusion criteria such as 1) including the published articles in the ISI journals and excluding 2) non-English and 3) preprints, slides, and conference papers. We use the PRISMA standard for systematic review. Results: The articles are categorized into the following main topics: estimation procedures, confidence regions, time series, and panel data, Bayesian, spatial, robust, testing, quantile regression, varying Coefficient Models, Variable Selection, Single-index model, Measurement error, Multiple Functions, Missing values, Rank Method and Others. There are different applications and datasets such as the Tecator dataset, air quality, electricity consumption, and Neuroimaging, among others. Conclusions: SFPLR is one of the most famous regression modeling methods for hybrid data that has a lot of extensions among other models.

Conventionally, partial differential equations (PDE) problems are solved numerically through discretization process by using finite difference approximations. The algebraic systems generated by this process are then finalized by using an iterative method. Recently, scientists invented a short cut approach, without discretization process, to solve the PDE problems, namely by using machine learning (ML). This is potential to make scientific machine learning as a new sub-field of research. Thus, given the interest in developing ML for solving PDEs, it makes an abundance of an easy-to-use methods that allows researchers to quickly set up and solve problems. In this review paper, we discussed at least three methods for solving high dimensional of PDEs, namely PyDEns, NeuroDiffEq, and Nangs, which are all based on artificial neural networks (ANNs). ANN is one of the methods under ML which proven to be a universal estimator function. Comparison of numerical results presented in solving the classical PDEs such as heat, wave, and Poisson equations, to look at the accuracy and efficiency of the methods. The results showed that the NeuroDiffEq and Nangs algorithms performed better to solve higher dimensional of PDEs than the PyDEns.

In this paper, we propose a partial differential equation model based on phase-field for sentiment analysis in the field of hotel comment texts. The comment texts are converted into word vectors using the Word2Vec tool, and then we utilize the multifractal detrended fluctuation analysis (MF-DFA) model to extract the generalized Hurst exponent of the word vector time series to achieve dimensionality reduction of the word vector data. The dimensionality reduced data is represented in a two-dimensional computational domain, and the modified Allen-Cahn (AC) function is used to evolve the phase values of the data to obtain a stable nonlinear boundary, thereby achieving automatic classification of hotel comment texts. The experimental results show that the proposed method can effectively classify positive and negative samples and achieve excellent results in classification indicators. We compared our proposed classifier with traditional machine learning models and the results indicate that our method possesses a better performance.

This paper proposes a solution for the development of microclimate monitoring for Low Voltage / High Voltage switchgear using the PRTG Internet of Things (IoT) platform. This IoT-based real time monitoring system can enable predictive maintenance to reduce the risk of electrical station malfunctions due to unfavorable environmental conditions. The combination of humidity and dust can lead to unplanned electrical discharges along the isolators inside a low or medium voltage electric table. If no predictive measures are taken, the situation may deteriorate and lead to significant damage inside and outside the switchgear cell. Thus, the mentioned situation can lead to unprogrammed maintenance interventions that can conduct to the change of the entire affected switchgear cell. Using a low-cost and efficient system, the climate conditions inside and outside the switchgear is monitored and transmitted remotely to a monitoring center. From the results obtained using a 365-day time interval, we can conclude that the proposed system is integrated successfully in the switchgear maintaining process, having as result the reducing of maintenance costs.

Information theory provides robust measures of multivariable interdependence, but classically does little to characterize the multivariable relationships it detects. The Partial Information Decomposition (PID) characterizes the mutual information between variables by decomposing it into unique, redundant, and synergistic components. This has been usefully applied, particularly in neuroscience, but there is currently no generally accepted method for its computation. Independently, the Information Delta framework characterizes non-pairwise dependencies in genetic datasets. This framework has developed an intuitive geometric interpretation for how discrete functions encode information, but lacks some important generalizations. This paper shows that the PID and Delta frameworks are largely equivalent. We equate their key expressions, allowing for results in one framework to apply towards open questions in the other. For example, we find that the approach of Bertschinger et al. is useful for the open Information Delta question of how to deal with linkage disequilibrium. We also show how PID solutions can be mapped onto the space of delta measures. Using Bertschinger et al. as an example solution, we identify a specific plane in delta-space on which this approach’s optimization is constrained, and compute it for all possible three-variable discrete functions of a three-letter alphabet. This yields a clear geometric picture of how a given solution decomposes information

Electric Transformers make up some of the most critical components of a power system. Their reliable operation is critical for an efficient power grid as well as economic viability for the transformer operators and owners. Power transformers, like other High Voltage (HV) electrical equipment experience aging and insulation degradation due to chemical, mechanical and electrical forces during their operation. Partial Dischargers (PD) are localized electrical discharges that develop within insulation systems of HV electrical equipment such as transformers. In transformers, PD occurs in different forms and various locations and insulation both internal and external of the transformer. PD originates as small pulses but tends to increase in size and intensity which can result in complete insulation failure. Monitoring partial discharges has proven to provide valuable information on the state of the insulation systems of the power transformer, allowing transformer operators to make calculated decisions for the maintenance and life of plant plans. This systematic literature review aims to systematically examine the use of machine learning techniques in classifying PD in transformers to present a complete indicator to allow for future research in the field. The systematic review surveyed a total of 81 research literature published from 2010 to 2023 that fulfilled a specific methodology which was developed as part of this study. The results revealed that supervised learning has been the most widely used Artificial Intelligence (AI) algorithm utilized, primarily in the form of Support Vector Machine (SVM). Regarding PD, the survey revealed that most researchers tend to use numerous types of PD and compare them to one another. Furthermore, the use of artificial PD defect models to simulate the occurrence of PD is widely used versus the use of actual power transformers. Most of the literature tends to not specify the physical characteristics of PD, such as the magnitude of PD, PD inception voltage and PD extinction voltage.

This study aimed at exploring what role artificial intelligence techniques could play in the futural numerical analysis. In this paper, a convolutional neural network techniques based on modified loss function is proposed as a surrogate of finite element method(FEM). Several surrogate-based physics-informed neural networks(PINNs) are developed to solve representative boundary value problems based on elliptic partial differential equations (PDEs). Results from the proposed surrogate-based approach are in good agreement with ones from conventional FEM. It is found that modification of the loss function could improve the prediction accuracy of the neural network. It is indicated that to some extent the artificial intelligence technique could replace conventional numerical analysis as a great surrogate model.

The technique of obtaining information or data about any feature or object from afar, called in technical parlance as remote sensing, has proven extremely useful in diverse fields. In the ecological sphere, especially, remote sensing has enabled collection of data or information about large swaths of areas or landscapes. Even then, in remote sensing the task of identifying and monitoring of different water reservoirs has proved a tough one. This is mainly because getting correct appraisals about the spread and boundaries of the area under study and the contours of any water surfaces lodged therein becomes a factor of utmost importance. Identification of water reservoirs is rendered even tougher because of presence of cloud in satellite images, which becomes the largest source of error in identification of water surfaces. To overcome this glitch, the method of the shape matching approach for analysis of cloudy images in reference to cloud-free images of water surfaces with the help of vector data processing, is recommended. It includes the database of water bodies in vector format, which is a complex polygon structure. This analysis highlights three steps: First, the creation of vector database for the analysis; second, simplification of multi-scale vector polygon features; and third, the matching of reference and target water bodies database within defined distance tolerance. This feature matching approach provides matching of one to many and many to many features. It also gives the corrected images that are free of clouds.

Background. Coronary artery disease (CAD) with extensive stenosis presents significant clinical challenges. This case report details the management and outcomes of a 61-year-old male with a notable history of CAD, initially treated with coronary artery bypass grafting (CABG), followed by an innovative intravenous hydrogen and oxygen nanobubble therapy due to recurrent symptoms.Case Presentation. Mr. BH was diagnosed with significant stenosis in the left anterior descending (LAD) artery and left circumflex (LCx) artery, initially managed by CABG. Recurring symptoms led to the adoption of a novel treatment involving hydrogen and oxygen nanobubbles. Following treatment initiation, Mr. BH experienced substantial improvements in physical capacity and symptomatic relief, with an ability to climb 22 flights of stairs and resolution of previous symptoms such as dyspnea and cough. Despite these improvements, subsequent imaging revealed in-stent restenosis and progression of graft disease.Discussion. The application of hydrogen and oxygen nanobubbles as a therapy in CAD is explored, highlighting potential mechanisms such as reduction of oxidative stress and improvement in endothelial function. This case contrasts the effects of conventional surgical and pharmaceutical interventions with the novel nanobubble therapy, illustrating both the benefits and complexities of managing advanced CAD with innovative treatments.Conclusion. While Mr. BH showed clinical improvement with nanobubble therapy, the development of new severe stenosis and restenosis underscores the need for further research to understand the long-term efficacy and mechanisms of nanobubble therapy in complex CAD cases. This case suggests that while innovative therapies may provide symptomatic relief and functional improvement, they do not obviate the need for ongoing surveillance and possibly further intervention.

Coral reefs are one of the most productive yet vulnerable ecosystems on Earth. An important step in understanding the functioning of coral communities is studying the environmental impact on the state of reefs. The present study aimed to assess the impacts of the water temperature, precipitation, wave action and population density on the seasonal bleaching, partial and complete mortality of shallow-water branching corals of Pocillopora verrucosa species complex. The present study was conducted at the Dam Bay research station (Nha Trang Bay) from 26 April 2020 to 2 April 2021. Throughout the study the percentage of bleached coral colonies varied from 1 to 41.5% with two peaks, in autumn (October) and spring (April). Rates of the development of partial mortality varied from 0 to 10%, with a pronounced peak in December. At the end of the experiment, the percentage of coral colonies suffering from partial mortality reached 47%. Only 4,5% of experimental colonies died by the end of the study. Analysis revealed that water temperature and partial mortality are the drivers of bleaching, while wave action, temperature and bleaching are the factors with a significant impact on partial mortality. In the present study, the main cause of coral death was the development of algal fouling at the sites of colony lesions, which gradually spread over the entire surface of the colony. We showed also that the impact of individual stress on mortality prevailed over the impact of seasonal bleaching and partial mortality events.

The conversion of methane into chemicals is of interest to achieve a decarbonized future. Fuel cells are electrochemical devices commonly used to obtain electrical energy, but can be utilized either for chemicals production or both energy and chemicals cogeneration. In this work, the partial oxidation of methane in fuel cells for electricity generation and valuable chemicals production at the same time is reviewed. For this purpose, different types of methane-fed fuel cells, both low temperature fuel cells, such as PEMFCs and AAEMFCs, and high temperature fuel cells, such as SOFCs, have been used. Also if few works have been devoted to this topic, the promising results drive the development of fuel cells using methane as the source for the cogeneration of power and valuable chemicals.

The operation of transformers suffers from natural or man-made disasters, subjecting the equipment to prolonged exposure to temperature, lightning strikes, transient over-voltages, and over-current, gradually producing insulation aging phenomenon, which results in partial discharges within the transformer. Without dealing with it beforehand properly, it may lead to insulation breakdown. Nowadays, with the mature development of microchip control technology and wireless communication technology, which is helpful for realizing the research for online real-time and long-term monitoring capabilities for power equipment. A transformer operating condition monitoring and diagnostic system that can rapidly and effectively prevent the breakdown of transformer insulation, which can impact the overall power supply system is developed in this paper. The system is divided into two parts based on its function. The first part is the operating condition monitoring and real-time alert unit for the transformer, primarily composed of an embedded computing module, a sensor module, and a transmission module. Its work content is to capture real-time online partial discharge ultrasonic signals and high frequency current comparator pulse signals, and analyze and determine the condition of the internal insulation and operational status whether it is fault or not. The second part is the central control unit, consisting mainly of an industrial computer and a transmission module. Its work content is to store the ultrasonic and high frequency current comparator pulse signals from the transformer operation monitoring and real-time alert unit. It uses the software to eliminate signal noise and interference, and then utilizes artificial neural networks to identify the type of fault. In this paper, the research for the phenomenon of insulation degradation in transformer equipment aims to establish aging trend profiles through the dual malfunctioning alert and aging process analysis, as well as the long-term measurement of ultrasonic signals from partial discharges and high-frequency current comparator pulse signals. This approach provides crucial reference data and a foundation for disposable on-site measurement, assessing the phenomenon of insulation aging stages, defects and damage of the transformers effectively. It allows for timely replacement or maintenance in advance, achieving the prevention of malfunctioning and predictive diagnosis of aging.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

The aim of this paper is to study a semi-functional partial linear regression model (SFPLR) for spatial data with responses missing at random. The estimators are constructed by the kernel method, and some asymptotic properties such as probability convergence rates of the nonparametric component and asymptotic distribution of the parametric and nonparametric components are established under certain conditions. Next, the performances and the superiority of these estimators are presented and examined using a study on simulated data and on real data by carrying out a comparison between our semi-functional partially linear model with MAR estimator (SFPLRM), the semi-functional partially linear model with the full-case estimator (SFPLRC) and the nonparametric functional model estimator with MAR (FNPM). The results show that the proposed estimators outperform existing estimators as the number of random missing data increases.

In this work, the analytical treatment of Fourth order pd equations has been discussed with the variational iteration algorithm with an auxiliary parameter. The technique has the capability of reducing the size of computational work and easily overcomes the difficulty of the perturbation method or Adomian polynomials. Comparison with the classic variational iteration algorithm- is carried out, showing that the modification is more efficient and reliable.

With the advancement of photoelectric technology and computer image processing technology, the visual measurement method based on point clouds is gradually applied to the 3D measurement of large workpieces. Point cloud registration is a key step in 3D measurement, and its registration accuracy directly affects the accuracy of 3D measurements. In this study, we designed a novel MPCR-Net for multiple partial point cloud registration networks. First, an ideal point cloud was extracted from the CAD model of the workpiece and was used as the global template. Next, a deep neural network was used to search for the corresponding point groups between each partial point cloud and the global template point cloud. Then, the rigid body transformation matrix was learned according to these correspondence point groups to realize the registration of each partial point cloud. Finally, the iterative closest point algorithm was used to optimize the registration results to obtain a final point cloud model of the workpiece. We conducted point cloud registration experiments on untrained models and actual workpieces, and by comparing them with existing point cloud registration methods, we verified that the MPCR-Net could improve the accuracy and robustness of the 3D point cloud registration.

The comparison of group means in item response models constitutes an important issue in empirical research. The present article discusses an extension of Haebara linking by proposing a flexible class of robust linking functions for comparisons of many groups. These robust linking functions are particularly suited to item response data that are generated under partial invariance. In a simulation study, it is shown that the newly proposed robust Haebara linking approach outperforms existing approaches of Haebara linking. In an empirical application using PISA data, it is illustrated that country means can be sensitive to the choice of linking functions.

In this study, we first present a time-fractional L$\hat{e}$vy diffusion equation of the exponential option pricing models of European option pricing and the risk-neutral parameter. Then, we modify a particular L$\hat{e}$vy-time fractional diffusion equation of European-style options. Introduce a more general model from the models based on the L$\hat{e}$vy-time fractional diffusion equation and review some recent findings regarding of the Europe option pricing of risk-neutral free.

With the increasing demand for precise condition monitoring and diagnosis of gas-insulated switchgears (GIS), it has become a challenge to improve the detection sensitivity of partial discharge (PD) induced in the GIS spacer. This paper deals with the elimination of the capacitive component from the phase resolved partial discharge (PRPD) signal generated in GIS spacer based on the discrete wavelet transform. Three types of typical insulation defects were simulated using PD cells. The single PD pulses were detected and were further used to determine the optimal mother wavelet. As a result, the bior6.8 was selected to decompose the PD signal into 8 levels and the signal energy at each level was calculated. The decomposed components related with capacitive disturbance were discarded whereas those associated with PD were de-noised by a threshold and a thresholding function. Finally, the PRPD signals were reconstructed using the de-noised components.

: Protease-producing yeasts were isolated from potato wastes and screened for protease production on skim milk agar plates The best producer of protease isolate was identified as Clavispora lusitaniae. The strain showed better enzyme production using tomato pomace and bread waste mix as a solid fermentation substrate. The optimized conditions improved enzyme activity and showed a maximal production of 33450±503 IU/g compared with the initial activity of 11205,78 ±360 without medium optimization. A threefold increase in protease activity after medium optimization proved the reliability of using the PBD and CCD design. A 19.76-fold purified enzyme and a yield of 32.94% were obtained after purification. The protease showed maximum activity at pH 4 and 60 °C and was resistant to Tween 20, Tween 40, SDS, and β-mercaptoethanol, Ca2+, and Mg2+ stimulated it. The protease activity was strongly inhibited in the presence of urea, and EDTA. The results revealed Clavispora lusitaniae protease's ability to degrade wheat seeds and flour gluten by 98.7% and 97% respectively under pH 4 for 24 hours at 40 °C. According to this study, this enzyme could be a potential candidate for the food industry, particularly for treating wheat seed and flour to reduce the immunogenicity of gluten.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

This study aims at the sustainable valorization of eggshells (ES) from different countries of origin in cement concrete as a cement replacement for Hong Kong. For this purpose, sixteen different eggs from different regions across the world were selected from the local market. Firstly, the extent of uniformity in the weight and mineral content of sampled eggshells were assessed by a specific gravity test and thermogravimetric analysis (TGA), respectively. It was found that specific gravity varies between 2.02 and 2.39, with an average value of 2.20 ± 0.01, whereas CaCO₃ varies between 94.65% and 97.23%, with an average value of 96.33%. These values were a bit lower than those of extra-pure limestone (LS) because of the organic part and the porous structure of eggshells. Secondly, three different eggshells were selected for cement replacement in cement concrete, both in the uncalcined and calcined states, based on having the highest, medium, and lowest CaCO₃ content, respectively. To get the calcined eggshells, the eggshells were calcined at 800^oC for three hours. It was found that the strength of eggshells varies with CaCO₃, but the variation was acceptable. The calcined eggshells showed comparatively more compressive strength and were close to the LS because of the free CaO and the absence of an organic part. In general, the variation in the basic properties of eggshells from different regions across the world is negligible and suitable to use as a cement replacement with acceptable variation in strength in Hong Kong.

The correct classification of defects originating from partial discharges (PD) in medium-voltage (MV) switchgears with air insulation (AIS) remains a challenging research topic for scientists worldwide. In this article, the authors simulated four possible defects occurring in the power industry, including one that is a simultaneous combination of two commonly ones. In addition, the correctness of the algorithm was checked by adding a classification class without any fault. The measurement signals were recorded with TEV sensors. The effectiveness of various hy-brid-connected neural networks was tested and discussed: GoogleNet and SqueezeNet based on spectrograms, SAE with FNN, 2D-CNN with LSTM, and hybrid AE combined with CNN and LSTM. The highest effectiveness – approximately 97% – was demonstrated by the GoogleNet and SqueezeNet networks. The research results are expected to form the basis for the development of a universal and wireless capacitive sensor for monitoring the level of PD in switchgears.

Asphalt cement will not last for a long time as the world encounters a diminishment in the crude oil. For sustainable, flexible pavement development, new resources can provide a contribution to replace it partially or entirely. In this study, asphalt was partially and entirely replaced by guayule resin as a bioresource by-product, extracted during the guayule natural rubber production. Crumb rubber modifier (CRM) was used as an asphalt enhancer. The Superpave grading system was followed at high, intermediate, and low temperatures to evaluate such innovative binder for rutting, fatigue, and thermal cracking, respectively, in addition to viscosity. Therefore, the original, short-term aging and long-term aging were simulated using tank, rolling thin film oven, and pressure aging vessel materials. Additionally, component analysis using Fourier-transform infrared spectroscopy was provided to link the rheological properties with the chemical changes. Outcomes showed a relatively much lower viscosity of guayule in the same high-temperature asphalt grade indicating savings in plant energy consumption and reduced environmental emissions. CRM enhanced guayule, but not as much as asphalt, proven by polymeric component migration through liquid binder. This enhancement was reflected in the rheological performance besides other factors. As-received guayule seems to have high oxygen content proven by strong absorption peak intensities of oxidative bonds (e.g., Carbonyl and sulfoxide). Such pre-oxidation was negatively reflected in the intermediate- and low-temperature performance of guayule and guayule-based binders. However, the investigated guayule had potential to compensate for asphalt replacement in the presence of CRM by 23–42% by weight of blend.

This study documents the conditions associated to white spruce and balsam fir regeneration after partial cutting. Measurements were collected 9 to 30 years after partial cutting in 12 natural fir stands and 5 white spruce plantations. We estimated seed input, measured light reaching the undergrowth, recorded seedlings (<150 cm) and their age on 6 different seedling establishment substrates: mineral soil, moss, rotten wood, litterfall, herbaceous and dead wood. Partial cutting generally favours the establishment and growth of seedlings. The number of fir and spruce seedlings is always greater in natural stands than in plantations, a trend likely associated with the reduced abundance of preferential establishment substrate in the latter. White spruce significantly prefers rotten wood while fir settles on all types of substrates that cover at least 10% of the forest floor. There is a strong relationship between light intensity and the median height of spruce seedlings, but this relationship is non-significant for fir. Seedlings of both species can survive at incident light intensities as low as 3%, but an intensity of 15% or more seems to offer the best growth conditions. The conditions for successful forest regeneration proposed in this study should be applied when the goal is to establish a new stand prior to clear cutting or to convert stand structure.

: We report the case of a 2-year-old Norwegian Forest cat diagnosed with pulmonary edema and pulmonary hypertension (PH) secondary to cor triatriatum sinister, who showed improved breathing following furosemide treatment. Sildenafil was prescribed post-discharge without diuretic. Thirty-eight days later, no abnormalities were observed in the septum or accessory chamber of the left atrium; however, continuous mosaic blood flow (maximum velocity, 3.14 m/s) was observed in two enlarged pulmonary veins. Pulmonary artery enlargement (main pulmonary artery to thoracic aorta ratio: 1.90), pulmonary vein stenosis (PVS), and diffuse bilateral ground-glass lung opacities were observed using computed tomography. PH with partial PVS and pulmonary parenchymal disease was diagnosed. The cat was further treated with furosemide with no clinical symptoms, but succumbed to acute dyspnea 51 days after the first visit. PH, despite partial PVS, may also be associated with concurrent parenchymal lung disease. Sildenafil can worsen pulmonary edema in the affected lung but did not in this case.

In this study, we present a numerical method for solving two--dimensional space--time fractional partial differential equations (FPDEs), where the solutions of the FPDEs are expanded in terms of the shifted Chebyshev polynomials. The numerical approximations are evaluated at the Chebyshev-Gauss-Lobatto points. In the case when the FPDE is nonlinear, we employ a Newton-Raphson approach to linearize the equation. Both the linear and nonlinear cases lead to a consistent system of linear algebraic equations. The scheme is tested on selected FPDEs and the numerical results show that the proposed numerical scheme is accurate and computationally efficient in terms of CPU times. To establish the accuracy of the method, we also present an error analysis which shows the convergence of the numerical method. These positive attributes make the proposed method a good approach for solving two--dimensional fractional partial differential equations with both space and time fractional orders.

Bohrnstedt’s (1969) attempt to derive a formula to compute the partial correlation coefficient and simultaneously correct for attenuation sought to simplify the process of performing each task separately. He suggested that his formula, developed from algebraic and psychometric manipulations of the partial correlation coefficient, produces a corrected partial correlation value. However, an algebraic error exists within his derivations. Consequently, the formula proposed by Bohrnstedt does not appropriately represent the value he intended it to estimate. By correcting the erroneous step and continuing the derivation based upon his proposed procedure, the steps outlined in this paper ultimately produce the formula that Bohrnstedt desired.

The removable partial denture, despite new technologies and new materials, continues to play a significant role in clinical dental practice. The purpose of the following study was to evaluate the design of new retention devices in Kennedy's second grade classrooms. For the study of "lamellar" retentive devices, 4 prosthetists were chosen and selected, according to inclusion and exclusion criteria, 16 patients, 8 women and 8 men, whose upper arch had to be rehabilitated with a removable partial prosthesis. The results showed that the parameters taken into consideration such as satisfaction, stability, aesthetics and retention had an average score higher than 3.30 (range 1-4), with an average standard deviation of 0.6225 in the 4 indicative parameters that the data they are relatively homogeneous and coherent. In conclusion we can state that the skeletonized prosthesis with lamellar retentions, designed in Kennedy's second grade classes, has shown good acceptance in selected patients

In the research we consider a structure-fluid interaction of oscillating piezodevice and acoustic liquid. Such problem requires finding resonance or anti-resonance frequencies of the solid structure to use them in the latter frequency-response analyses step. After finite element discretization of the issue, we need to solve a generalized eigenvalue problem (GEP). The most efficient numerical method for solving the partial GEP is the shift-and-invert Lanczos method. Each step of this algorithm requires solving a large scale system of linear algebraic equations (SLAEs) with special properties. Various ways of ordering grid nodes lead to coefficient matrices with different structure. Several methods are compared in terms of efficiency. The results of the numerical experiments are presented.

In order to obtain the good match between yield strength and low-temperature toughness, the short-time partial austenitization (SPA) process was employed for V-microalloying 0.22C-5.24Mn steel. The initial microstructure after intercritical tempering was dual-phase ferrite and reversed austenite (RA), while the final microstructure was consisted of ferrite, RA and secondary martensite (SM) after subjected to SPA process. (V, Mo)C with disc-like morphology mainly precipitated during intercritial tempering, and the aspect ratio of particle decreased, leading to the appearance of near-spherical morphology. After subjected to SPA process, the resultant multiphase hierarchical microstructure (three layers: out layer of ferrite, interlayer of SM and inner layer RA) enabled high yield strength of 1097 MPa, total elongation of 14%, and impressive impact energy of 33.3 J at -20 °C. The strengthening contribution of (V, Mo)C precipitation was estimated about 108 MPa.

Zidovudine (AZT) has significantly reduced the mortality and morbidity rates among AIDS patients, but it has been associated with hepatotoxicity. AZT treatment has been linked to disrupted lipid and glucose metabolism, and the enhancement of pro-inflammatory chemokines and other mediators, which can lead to liver steatosis. In contrast, the administration of adenosine (ADO) has proven to be an effective hepatoprotector against both acute and chronic liver damage. Therefore, present study was aimed to investigate the harmful effects of chronic AZT administration and the beneficial effects of the co-administered ADO. Chronic oral AZT administration did not induce hyperglycemia or dyslipidemia, but serum liver marker enzyme activities were increased, as well as evidence of liver steatosis and inflammation. These findings were associated with low insulin and glucagon levels, elevated serum levels of pro-inflammatory cytokines and disruptions in cell redox states in these animals. ADO co-administration attenuated the deleterious effects induced by AZT: blocking the production of inflammatory molecules, increasing serum insulin and glucagon levels, and restoring liver cellular redox state. Then, blood insulin levels seemed to be greatly influenced by the cellular redox state, which was altered by AZT administration. This alteration is likely to be connected to mitochondrial integrity and metabolism.

Alzheimer’s Disease (AD) has no cure. Earlier, we showed that partial inhibition of mitochondrial complex I (MCI) with small molecule CP2 induces adaptive stress response activating multiple neuroprotective mechanisms. Chronic treatment reduced inflammation, improved synaptic and mitochondrial functions, and blocked neurodegeneration in symptomatic APP/PS1 mice, a translational model of AD. Here, using serial block-face scanning electron microscopy (SBFSEM) and three-dimensional (3D) EM reconstructions combined with Western blot analysis and next-generation RNA sequencing, we demonstrate that CP2 treatment also restores mitochondrial morphology and mitochondria-endoplasmic reticulum (ER) communication in the APP/PS1 mouse brain. Using 3D EM volume reconstructions, we show that mitochondria in AD dendrites exist primarily as mitochondria-on-a-string (MOAS). Compared to other morphological phenotypes, MOAS are extensively enveloped in the ER membranes forming multiple mitochondria-ER contact sites (MERCS) known to contribute to abnormal lipid and calcium homeostasis. CP2 treatment specifically reduced MOAS formation, consistent with improved energy homeostasis in the brain, with concomitant reduction in MERCS, ER stress, and improved lipid homeostasis. These data provide novel information on the role MOAS play in AD and additional support for further development of partial MCI inhibitors as disease modifying strategy for AD.

Objective: About a third of schizophrenia patients are treatment-resistant to antipsychotic therapy. No studies established the fingerprints or pathway-phenotypes of treatment-resistant schizophrenia. The present study aimed to delineate the pathway-phenotypes of non-responders (NRTT) and partial responders (PRTT) to treatment using machine learning. Methods: We recruited 115 schizophrenia patients and 43 healthy controls and measured schizophrenia symptom dimensions, neurocognitive tests, plasma CCL11, interleukin-(IL)-6, IL-10, Dickkopf protein 1 (DKK1), high mobility group box-1 protein (HMGB1), κ- and µ-opioid receptors (KOR and MOR, respectively), endomorphin-2 (EM-2), and β-endorphin. Results: Machine learning showed that the NRTT group is a qualitatively distinct class and is significantly discriminated from PRTT with an accuracy of 100% using a neuro-immune-opioid-cognitive (NIOC) pathway-phenotype with as main determinants list learning, controlled word association, and Tower of London test scores, CCL11, IL-6, and EM2. The top-5 symptom domains separating NRTT from PRTT were in descending order: psychomotor retardation, negative symptoms, psychosis, depression, and mannerism. Moreover, a NIOC pathway also discriminated PRTT from healthy controls with an accuracy of 100% while all PRTT and controls were authenticated as belonging to their respective classes. Conclusion: A non-response to treatment with antipsychotics is determined by increased severity of specific symptom profiles coupled with deficits in executive functions, and episodic and semantic memory, and aberrations in neuro-immune and opioid pathways. No patients showed complete remission after treatment indicating that non-remitting in PRTT is attributable to increased HMGB1 and residual deficits in attention, executive functions, and semantic memory.

As society becomes more reliant on Lithium-ion (Li-ion) batteries, state-of-health (SOH) estimation will need to become more accurate and reliable. Therefore, SOH modelling is in the process of shifting from using simple and continuous charge/discharge profiles, to more dynamic profiles constructed to mimic real operation, when ageing the Li-ion batteries. However, in most cases, when ageing the batteries, the same exact profile is just repeated until the battery reaches its end-of-life. Using data from batteries aged in this fashion to build a model, there is a very real possibility that the model will rely on the built-in repetitiveness of the profile. Therefore, this work will examine the dependence of the performance of a multiple linear regression on the number of charges used to train the model, and their location within the profile used to age the batteries. The investigation shows that it is possible to build models using randomly selected partial charges while still reaching errors as low as 0.5%. Furthermore, it shows that only two randomly sampled partial charges are needed to achieve errors of less than 1%. Lastly, as the number of randomly sampled partial charges used to create the model increases, then the dependence on particular partial charges tends to decrease.

Biodiesel is one of the most popular biofuels as it is a promising substitute of the conventional diesel fuel, but for now it cannot be used as a stand-alone fuel due to its low oxidative stability. For this reason, the last years there have been efforts for its upgrading through the partial hydrogenation of the fatty acid methyl esters (FAMEs) that biodiesel consists of. This procedure succeeds in resolving the problem of low oxidative stability, but in some cases a new problem arises as the non-selective hydrogenation is deteriorating the fuel’s cold flow properties, which are crucial for its operation without damaging the vehicle’s engine. More specifically, the problem of deteriorated cold flow properties is caused by the formation of trans-monounsaturated FAMEs and fully saturated FAMEs while the hydrogenation reaction is taking place. The hydrogenated biodiesels are preferred to contain more cis-monounsaturated FAMEs, because these are considered to have the best combination between high oxidative stability and good cold flow properties. As a result, various systems and methods have been tested in order to achieve a selective partial hydrogenation of biodiesel’s FAMEs. In this review article, the catalytic systems and methods that stood out in various researches are presented and the factors that lead to the best possible outcome are investigated and discussed.

We report on the use of quartz-enhanced photoacoustic spectroscopy (QEPAS) for multi-gas detection. Photo-acoustic (PA) spectra of mixtures of water (H2O), ammonia (NH3) and methane (CH4) were measured in the mid-infrared (MIR) wavelength range using a MIR (mid-infrared) optical parametric oscillator (OPO) light source. Highly overlapping absorption spectra is a common challenge for gas spectroscopy. To mitigate this, we use a partial least-squares regression (PLS) method to estimate the mixing ratio and concentrations of the individual gasses. The concentration range explored in the analysis varies from a few parts-per-million (ppm) to thousands of ppm. Spectra obtained from HITRAN and experimental single-molecule reference spectra of each of the molecular species were acquired and used as training data sets. These spectra were used to generate simulated spectra of the gas mixtures (linear combinations of the reference spectra). Here in this proof-of-concept experiment we demonstrate that after an absolute calibration of the QEPAS cell, the PLS analyses could be used to determine concentrations of single molecular species with a relative accuracy within a few % for mixtures of H2O, NH3 and CH4 and with an absolute sensitivity of approximately 300(±50) ppm/V, 50(±5) ppm/V and 5(±2) ppm/V for water, ammonia and methane, respectively. Thus, demonstrating that QEPAS assisted by PLS is a powerful approach to estimate concentrations of individual gas components with considerable spectral overlap, which is a typical scenario for real-life adoptions and applications.

The use of artificial intelligence in natural language processing (NLP) has significantly contributed to the advancement of natural language applications such as sentimental analysis, topic modeling, text classification, chatbots, and spam filtering. With a large amount of text generated each day from different sources such as webpages, blogs, emails, social media, and articles, one of the most common tasks in natural language processing is the classification of a text corpus. This is important in many institutions for planning, decision-making, and archives of their projects. Many algorithms exist to automate text classification operations but the most intriguing of them is that which also learns these operations automatically. In this study, we present a new model to infer and learn from data using probabilistic logic and apply it to text classification. This model, called GenCo, is a multi-input single-output (MISO) learning model that uses a collaboration of partial classifications to generate the desired output. It provides a heterogeneity measure to explain its classification results and enables the reduction of the curse of dimensionality in text classification. The classification results are compared with those of conventional text classification models, and it shows that our proposed model has a higher classification performance than conventional models.

A common challenge in real-world classification scenarios with sequentially appending target domain data is insufficient training datasets during the training phase. Therefore, conventional deep learning and transfer learning classifiers are not applicable especially when individual classes are not represented or are severely underrepresented at the outset. Domain Generalization approaches reach their limits when domain shifts become too large, making them occasionally unsuitable as well. In many (technical) domains, however, it is only the defect/ worn/ reject classes that are insufficiently represented, while the non-defect class is often available from the beginning. The proposed classification approach addresses such conditions and is based on a CNN encoder. Following a contrastive learning approach, it is trained with a modified triplet loss function using two datasets: Besides the non-defective target domain class (= 1st dataset), a state-of-the-art labeled source domain dataset that contains highly related classes (e.g., a related manufacturing error or wear defect) but originates from a (highly) different domain (e.g., different product, material, or appearance) (= 2nd dataset) is utilized. The approach learns the classification features from the source domain dataset while at the same time learning the differences between the source and the target domain in a single training step, aiming to transfer the relevant features to the target domain. The classifier becomes sensitive to the classification features and – by architecture – robust against the highly domain-specific context. The approach is benchmarked in a technical and a non-technical domain and shows convincing classification results. In particular, it is shown that the domain generalization capabilities and classification results are improved by the proposed architecture, allowing for larger domain shifts between source and target domains.

A partial aperture onboard calibration method can solve the onboard calibration problems of some large aperture remote sensors, which is of great significance for the development trend of increasingly large apertures in optical remote sensors. In this paper, the solar diffuser reflectance degradation monitor (SDRDM) in the onboard calibration assembly (CA) of the FengYun-4 (FY-4) advanced geostationary radiance imager (AGRI) is used as the reference radiometer for measuring the partial aperture factor (PAF) for the AGRI onboard calibration. First, the linear response count variation relationship between the two is established under the same radiance source input. Then, according to the known bidirectional reflection distribution function (BRDF) of the solar diffuser (SD) in the CA, the relative reflectance ratio coefficient between the AGRI observation direction and the SDRDM observation direction is calculated. On this basis, the response count value of the AGRI and the SDRDM is used to realize the high-precision measurement of the PAF of the AGRI B1 ~ B3 bands by simulating the AGRI onboard calibration measurement under the illumination of a solar simulator in the laboratory. According to the determination process of the relevant parameters of the PAF, the measurement uncertainty of the PAF is analyzed; this uncertainty is better than 2.04% and provides an important reference for the evaluation of the onboard absolute radiometric calibration uncertainty after launch.

We investigate the behavior of the partial derivative approach to the change of scale formula and prove relationships among the analytic Wiener integral and the analytic Feynman integral of the partial derivative for the function space integral.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.

Image restoration plays a vital role in image processing and pattern recognition in producing better recognition accuracy. It was observed that, most of the traditional restoration algorithms were meant for removing a single type of noise and efforts have been made towards the use of partial differential equation model (PDE), to restore different types of images such as super-resolution, bleeding through and deblurring. This research work deployed hybridized shock filter, shock diffusion of higher order PDE to remove degraded images that have been affected by atmospheric turbulence and water smear images. Degraded images of different types were acquired from various sources. The degraded images were subjected to shock filter algorithm, shock diffusion of higher order PDE. The shock filter was combined with PDE, likewise the shock diffusion was also combined with PDE, and the three algorithms were also combined to test the efficiency of the hybridized method on different degraded images. The result was validated using Mean Square Error, Structural Similarity Index Measure (SSIM), Peak-to-Noise-Signal -Ratio (PNSR) and universal quality index (UQI). From the result, it was observed that the combination of many image restoration algorithms does not give better results whereas, the combination of two of the algorithms has really proved effective.

Background. Gene rearrangements affecting KMT2A are frequent in acute myeloid leukemia (AML) and are often associated with a poor prognosis. KMT2A gene fusions are often detected by chromosome banding analysis and confirmed by fluorescence in-situ hybridization. However, small intragenic insertions, termed KMT2A partial tandem duplication (PTD), are particularly challenging to detect using standard molecular and cytogenetic approaches. Methods. We have validated the use of a custom hybrid capture based next-generation sequencing (NGS) panel for comprehensive profiling of AML patients seen at our institution. This NGS panel targets the entire consensus coding DNA sequence of KMT2A; to deduce the presence of a PTD we used the relative ratio of KMT2A exons coverage. We sought to corroborate the KMT2A-PTD NGS results using (1) multiplex-ligation probe amplification (MLPA) and (2) optical genome mapping (OGM). Results. We analyzed 932 AML cases and identified 41 individuals harboring a KMT2A-PTD. MLPA, NGS and OGM confirmed the presence of a KMT2A-PTD in 22 of the cases analyzed where orthogonal testing was possible. Two false positive PTD calls by NGS could be explained by the presence of cryptic structural variants impacting KMT2A and interfering with PTD analysis. OGM revealed the nature of these previously undetected gene rearrangements in KMT2A, while MLPA yielded in-conclusive results. MLPA analysis for KMT2A-PTD is limited to exon 4, whereas NGS and OGM resolved KMT2A-PTD sizes and copy number levels. Conclusion. KMT2A-PTDs are complex gene rearrangements that cannot be fully ascertained using a single genomic platform. MLPA, NGS panels and OGM are complementary technologies applied in standard of care testing for AML patients. MLPA and NGS panels are designed for targeted copy number analysis; however, our results show that integration of concurrent genomic alterations is needed for accurate KMT2A-PTD identification. Unbalanced chromosomal rearrangements overlapping with KMT2A can interfere with the diagnostic sensitivity and specificity of copy number based KMT2A-PTD detection methodologies.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

Partial least square (PLS) regression is a well-known chemometric method used for predictive modelling, especially in the presence of many variables. Although PLS was not initially developed as a technique for classification tasks, scientists have reportedly used this approach successfully for discrimination purposes. Whereas some non-supervised learning approaches including but not limited to PCA, and k-means clustering do well in identifying/understanding grouping and clustering patterns in multidimensional data, they are limited when the end target is discrimination, making PLS a preferable alternative. A total of fertilized 672 chicken egg hyperspectral imaging data, consisting of 336 white eggs and 336 brown eggs were used in this study. Hyperspectral images in the NIR region of 900-1700 nm wavelength range were captured prior to incubation on day 0 and on days 1-4 after incubation. Eggs were candled on incubation day 5 and broken out on day 10 to confirm fertility. While a total number of 312 and 314 eggs were found to be fertile in the brown and white egg batches respectively, total numbers of non-fertile eggs in the same set of batches were 23 and 21 respectively. Spectral information was extracted from a segmented region of interest (ROI) of each hyperspectral image and spectral transmission characteristics were obtained by averaging the spectral information. A moving-thresholding technique was implemented for discrimination based on PLS regression results on the calibration set. With true positive rates (TPR) of up to 100% obtained at selected threshold values of between 0.50-0.85 and on different days of incubation, the results indicated that the proposed PLS technique can accurately discriminate between fertile and non-fertile eggs. The adaptive PLS approach was thereby presented as suitable for handling hyperspectral imaging-based chicken egg fertility data

The information data accuracy affects the working reliability of production management system directly. Mobile equipment is an important part of integrated manufacturing system, in the course of its works, due to the complex working environment and the dynamic change of its position, it lead to the important problem of information detection distortion. Because the application of fractional differential operator has the dual functions of enhancing signal strength and reducing data error, we puts forward a data processing method of obtaining production information data of various accuracy by changing the parameters of fractional differential operator. Establish a mobile equipment detection data fusion processing model based on fractional order partial differential equations and apply it in the processing experiment of mobile equipment testing information detection data in an integrated manufacturing system, the feasibility and effectiveness of the method are verified. We conclude that the fractional order partial differential equations used in the processing of mobile equipment monitoring information data of an integrated manufacturing system has the function of obtaining production information data of various accuracy, which are of great significance to improve the working reliability in integrated manufacturing system. which is of great significance to improve the working reliability and scientific decision of integrated manufacturing system.

Objective: One of the major causes of cerebral ventricular shunt failure is proximal catheter occlusion. We describe a novel ventricular cerebrospinal fluid (CSF) flow replicating system that assesses pressure and flow responses to varied degrees of catheter occlusion. Methods: Ventricular catheter performance was assessed during conditions of partial and complete occlusion. The catheters were placed into a three-dimensionally printed phantom ventricular replicating system. Artificial CSF was pumped through the ventricular system at a constant rate of 1 ml/min to mimic CSF flow, with the proximal end of the catheter in the phantom ventricle. Pressure transducer and flow rate sensors were used to measure intra-phantom pressure, outflow pressure and CSF flow rates. The catheters were also inserted into silicone tubing and pressure was measured in the same manner for comparison with the phantom. Results: Pressure measured in the phantom ventricle did not change when the outflow of the ventricular catheter was partially occluded. However, the intraventricular phantom pressure significantly increased when the outflow catheter was 100% occluded. Flow through the catheter showed no significant difference in rate with any degree of partial occlusion of the catheter. At the distal end of the partially occluded catheters, there was less pressure compared with the nonoccluded catheters. This difference in pressure in partially occluded catheters correlated with the percentage of catheter hole occlusion. Conclusions: Our model mimics physiological dynamics of the CSF flow in partially and completely obstructed ventricular catheters. We found that partial occlusion of the catheter had no effect on CSF flow rate, but did reduce outflow pressure of the catheter.

Often, when solving forward, inverse or data assimilation problems, only a part of the solution is needed. As a model, we consider the stationary diffusion problem. We demonstrate an algorithm that can compute only a part or a functional of the solution, without calculating the full inversion operator and the complete solution. It is a well-known fact about partial differential equations that the solution at each discretisation point depends on the solutions at all other discretisation points. Therefore, it is impossible to compute the solution only at one point, without calculating the solution at all other points. The standard numerical methods like a conjugate gradient or Gauss elimination compute the whole solution and/or the complete inverse operator. We suggest a method which can compute the solution of the given partial differential equation 1) at a point; 2) at few points; 3) on an interface; or a functional of the solution, without computing the solution at all points. The required storage cost and computational resources will be lower as in the standard approach. With this new method, we can speed up, for instance, computation of the innovation in filtering or the likelihood distribution, which measures the data misfit (mismatch). Further, we can speed up the solution of the regression, Bayesian inversion, data assimilation, and Kalman filter update problems. Applying additionally the hierarchical matrix approximation, we reduce the cubic computational cost to almost linear $\mathcal{O}(k^2n \log^2 n)$, where $k\ll n$ and $n$ is the number of degrees of freedom. Up to the hierarchical matrix approximation error, the computed solution is exact. One of the disadvantages of this method is the need to modify the existing deterministic solver.

Researchers in different disciplines studied liver’s genetic expression of organogenesis in embryogenesis; however, organogenesis has not been studied as an independent and a complementary process during adult liver regeneration. This paper reviewed studies and extracted information related to organogenesis in adult liver regeneration because of organogenesis’ important role in cancer and tissue regeneration.

Viral infection can regulate the cell cycle, thereby promoting viral replication. Hijacking and altering the cell cycle are important for the virus to establish and maintain latent infection. Previously, Spodoptera exigua multiple nucleopolyhedrovirus (SeMNPV) latently infected P8-Se301-C1 cells, which grew more slowly than Se301 cells and interfered with homologous SeMNNPV superinfection, were established. However, the effects of latent and superinfection with baculoviruses on cell cycle progression remain unknown. In this study, the cell cycle profiles of P8-Se301-C1 cells, and SeMNPV or Autographa californica mutiple nucleopolyhedrovirus (AcMNPV) infected P8-Se301-C1 cells were characterized by flow cytometry. The results showed that replication-related genes MCM4, PCNA, and BAF were down-regulated (p < 0.05) in P8-Se301-C1 cells and the S phase of P8-Se301-C1 cells was longer than that of Se301 cells. P8-Se301-C1 cells infected with SeMNPV did not arrest in G2/M phase and or affect the expression of Cyclin B and cyclin-dependent kinase 1 (CDK1). Furthermore, when P8-Se301-C1 cells were infected with SeMNPV after synchronized treatment with hydroxyurea and nocodazole, light microscopy and qRT-PCR analysis showed that compared with unsynchronized cells and S and G2/M phase cells, SeMNPV-infected P8-Se301-C1 cells in G1 phase induced G2/M phase arrest, and the amount of virus adsorption and intracellular viral DNA replication were significantly increased (p < 0.05). In addition, the BV production and the OB containing cells were both increased at 120 h post-infection (p < 0.05). The expression of Cyclin B and CDK1 was significantly down-regulated at 48 h post infection (p < 0.05). Finally, arrest of SeMNPV-infected G1 phase cells in the G2/M phase increased BV production (p < 0.05) and the number of OB containing cells. In conclusion, G1 phase infection and G2/M arrest are favorable to SeMNPV proliferation in P8-Se301-C1 cells, thereby alleviating the homologous superinfection exclusion. The results contribute to a better understanding of the relationship between baculoviruses and insect cell cycle progression regulation.

This prospective observational cohort pilot study included 22 cats diagnosed with partial traumatic brachial plexus injury (PTBPI), aiming to explore the response of an early intensive neurorehabilitation protocol in a clinical setting. This protocol included functional electrical stimulation (FES), locomotor treadmill training and kinesiotherapy exercises, starting at the time with highest probability of nerve repair. The synergetic benefits of this multimodal ap-proach were based on the potential structural and protective role of proteins and release of neurotrophic factors. Furthermore, parametrization of FES was according to the presence or absence of deep pain. Results have shown that 72.6% (16/22) cats achieved ambulation, with 9 cats within 15 days, 2 cats until 30 days and 5 cats until 60 days. During the 4 years follow-up, there was evidence of improvement on both muscle mass and muscle weakness, in addition to the disappearance of neuropathic pain. Notably, after the 60 days of neurorehabilitation, 3 cats improved ambulation after arthrodesis of the carpus. Thus, early rehabilitation, with FES ap-plied at the first weeks after injury and accurate parametrization according to the deep pain perception, is suggestive to help in functional recovery and ambulation, reducing probability of amputation.

Congenital diseases of the large intestine have scarcely been reported and mostly include fistula, atresia, or colonic duplication. Cases of partial colonic agenesis have rarely been described. The purpose of this study was to report a cohort of dogs and cats diagnosed with partial colonic agenesis. The colon was measured during colonoscopy or contrast-radiography and compared to the average length described in the literature. Six dogs and 17 cats were retrospectively included. Depending on the case, partial colonic agenesis could represent an incidental finding or the likeliest cause of clinical signs. Diarrhea was reported in most cases, and no specific clinical or biological abnormality was observed. Median age of presentation was variable and long asymptomatic periods were common. Abdominal ultrasound was useful and identified a short colon in 14/17 cats but only in one dog. Endoscopy was useful to confirm the diagnosis and to identify associated lesions and complications. Among others, colonic stenosis was reported in 8/9 cases that had lifelong clinical signs and the shortest colon length. This anatomical abnormality could promote chronic inflammation that might generate fibrosis and ultimately stenosis.

An irreparable rotator cuff tear is a challenging condition to treat, and various treatment modalities are being introduced. Medialization in the partial repair method has the limitation of exposing the tuberosity, while tension-free biologic interpositioning tuberoplasty using acellular dermal matrix (ADM) has the limitation of exposing the humeral head. The authors believe that by combining these two techniques, it is possible to complement each other's limitations. Therefore, they propose a surgical method that combines medialization and biologic interpositioning tuberoplasty for addressing these constraints.

This prospective cohort pilot study included 22 cats diagnosed with partial traumatic brachial plexus injury (PTBPI), aiming to explore the response of an early intensive neurorehabilitation protocol. This protocol included functional electrical stimulation (FES), locomotor treadmill training and kinesiotherapy exercises, starting at the time with highest probability of nerve repair. The synergetic benefits of this multimodal approach were based on the structural and protective role of proteins and release of neurotrophic factors. Furthermore, parametrization of FES was according to presence or absence of deep pain. Results have shown 72.6% (16/22) cats that achieved ambulation, with 9 cats within 15 days, 2 cats until 30 days and 5 cats until 60 days, however with persistent knuckling position. During the 4 years follow-up, there was evidence of improvement on both muscle mass and muscle weakness, in addition to the disappearance of neuropathic pain. Notably, after the 60 days of neurorehabilitation, 3 cats improved ambulation after arthrodesis of the carpus. Thus, early rehabilitation, with FES applied at the first weeks after injury and accurate parametrization according to deep pain perception, may improve functionality and ambulation, reducing probability of amputation of the affected limb.

(1) Background: Surgical phases form the basic building blocks for surgical skill assessment, feedback and teaching. Phase duration itself and its correlation to clinical parameters has not yet been investigated. Novel commercial platforms provide phase indications but have not been assessed for accuracy yet. (2) Methods: We assess 100 robot-assisted partial nephrectomy videos for phase duration based on previously defined proficiency metrics. We develop an annotation framework and subsequently compare our annotations to an existing commercial solution (Touch Surgery, Medtronic™). We subsequently explore clinical correlations between phase durations and peri-operative parameters. (3) Results: Objective and uniform phase assessment requires precise definitions derived from an iterative revision process. Comparison to a commercial solution shows large differences in definitions across phases. BMI and duration of renal tumor identification correlate positively, as well as tumor complexity and both tumor excision and renorraphy duration. (4) Conclusions: Surgical phase duration can be correlated with certain clinical outcomes. Further research should investigate if retrieved correlations are also clinically meaningful. This requires increasing dataset sizes and facilitation through intelligent computer vision algorithms. Commercial platforms can facilitate this dataset expansion and help unlock the full potential, provided the disclosure of phase annotation details.

Keywords: oligozoospermia; male infertility; epididymis; scrotal exploration; scrotal ultrasound; partial epididymal obstruction

Increasing CO2 concentration ([CO2]) in atmosphere decreases mineral nutrients concentration in crops whereas increasing water use efficiency (WUE) especially in drought conditions. Partial root-zone irrigation (PRI) could stimulate soil nutrient mineralization and improve crop nutrient status. Yet the effect of PRI combined with elevated CO2 concentration (e[CO2]) on the element stoichiometry of tomato leaves remains unknown. This study was to investigate the responses of leaf mineral nutrients status and element stoichiometric ratio in tomato grown at PRI exposed to e[CO2]. Tomato plants (cv. Ailsa Craig) were grown in pots in climate-controlled growth chambers with ambient [CO2] (a[CO2], 400ppm) and elevated [CO2] (e[CO2] 800ppm), respectively. Three irrigation regimes (IR) i.e. full irrigation (FI), deficit irrigation (DI) and partial root-zone irrigation (PRI) were applied to tomato plants at flowering stage. The result showed that plants exposed to both reduced irrigations had a similar biomass, an enhanced root growth including greater root to shoot ratio (R/S), root length (RL), surface area (RS), volume (RV) and specific length (RSL), and an improved WUE under e[CO2]. Compared to a[CO2], e[CO2] growth environment resulted in a similar leaf [C], [K] and [Mg], leaf C/K and C/Mg, increased leaf [Ca], [S] and leaf C/N, C/P and N/P, but decreased leaf [N], [P], leaf C/Ca, C/S and N/K at PRI. Additionally, under e[CO2], PRI showed an increase in leaf [C], [N] and [S], no decrease in leaf [K], Ca], [Mg], [S] and [15N], but a decrease in leaf C/N and C/S as compared with FI. Conclusively, PRI had the ability to alleviate the negative effects on mineral nutrient concentrations and maintain or improve most leaf element stoichiometric ratios under e[CO2]. Therefore PRI would be a practicable irrigation for optimizing WUE and nutrient status in tomato leaves in a future freshwater-limited and higher CO2 environment.

Background: Wilms tumor (WT) is the main renal tumor in children. SIOP-UMBRELLA Guidelines admit Nephron sparing surgery (NSS) in syndromic patients, and in small (&lt;300 ml) nonsyndromic unilateral WTs, without lymph node involvement, and with a substantial expected remnant renal function, after neoadjuvant chemotherapy. We report our prechemotherapy transperitoneal robot-assisted partial nephrectomy (RAPN) in a unilateral non-syndromic Wilms tumor. Methods: A 6-year-old-child showed an exophytic 3.6 cm diameter solid rounding mass involving the upper right renal pole at an incidental abdominal echotomography. CT-scan and abdominal MRI proved no local infiltration neither lymph node involvement was appreciated, suggesting an exophytic mass easily resectable through a NSS robotic approach, with a low risk of rupture and no subverted renal anatomy. The preoperative imaging was not suggestive for WT. A virtual 3D reconstruction of the tumor was performed. Results: the oncologic board approved a robot-assisted partial nephrectomy with the intraperitoneal approach. The histopathologic analysis displayed a WT. The patient underwent 10 vincristine-doses adjuvant chemotherapy. 28-months follow-up showed no tumor recurrence. Conclusions: Intraperitoneal RAPN can represent an opportunity for WT and needs to be assessed as a challenging possibility. This case suggests a potential role of prechemotherapy RAPN in the near future for highly selected patients.

In recent years, the number of open preservation surgeries for treatment of laryngeal Cancer has increased. The purpose of this surgery is to avoid the highly mutilating intervention of a total laryngectomy (TL) and to maintain laryngeal function while ensuring oncological radicality. The aim of this study was to assess the oncologic results of OPHL I and II and to identify prognostic factors that could impact patient survival and local failure rates. This study was conducted on 182 patients with laryngeal squamous cell carcinoma treated with OPHLs between 2005 and 2015. The survival rates of a group of patients treated with TL between 2004 and 2014 were taken into con-sideration to compare survival outcomes. The DSS in pT2 and pT3 tumors in relation to the type of surgery showed no statistically significant difference between OPHLs and TL (p=0.54 and p=0.63 respectively). The 5-years T-recurrence free survival showed that pT4 tumors, perineural/vascular positive invasion and OPHL IIb + ARY treated tumors were associated with a higher risk of tumor recurrence (p<0.0001, p=0.0005 and p=0.016 respectively). OPHLs represent an excellent alterna-tive to TL considering the characteristics of the tumor and the general conditions of the patient.

Laparoscopic partial nephrectomy (LPN) after hyperselective embolization of tumor vessels (HETV) in a hybrid operating room (HOR) that combines traditional surgical equipment with advanced imaging technology, is a non-clamping surgical approach to treat localized kidney tumors that have shown promising short-term results. The aim of this study was to evaluate the long-term oncological and functional outcomes of this procedure. All consecutive patients treated for a localized kidney tumor by LPN after HETV between May 2015 and October 2022 in a single academic institution were included in the study. Clinical, pathological and biological data were collected prospectively in the uroCCR database. We evaluated perioperative data, postoperative complications, surgical margin and modification of renal function after surgery. We included 245 patients. Median tumor size was 3.2 (2.5-4.4) cm. The R.E.N.A.L. complexity was low, medium and high for 104 (43.5%), 109 (45.6%) and 26 (10.9%) patients, respectively. Median LPN time was 75 (65 -100) min and median blood loss was 100 (50-300) mL. Surgical postoperative complications occurred in 56 (22.9%) patients with 17 (5.7%) major complications. The median preoperative Glomerular Function Rate (GFR) was 90.5 (77-101.8) mL/min and the median GFR variation at 6 months was -7.5 (-15- -2) mL/min. Malignant tumors were present in 211 (86.1%) patients and 12 (4.9%) patients had positive surgical margins. After a median follow-up of 27 (8-49) months, 20 (8.2%) patients had a tumor recurrence and 4 (1.6%) died from cancer. The use of a HOR to perform LPN after HETV is a safe and efficient non-clamping approach to treat localized kidney tumors.

Legionella pneumophila RpoS (LpRpoS) is an alternative sigma factor of RNA polymerase (RNAP) essential for virulence and stress resistance. To investigate the mechanism of RpoS in the intracellular pathogen L. pneumophila, we determined the high-resolution crystal structure of the LpRpoS (residues 95-194) containing a partial region 1.2 and region 2. The structure of LpRpoS (residues 95-194) reveals that the conserved residues are critical for promoter melting, DNA and core RNAP binding. The differences in regulatory factor binding site between Escherichia coli RpoS and LpRpoS suggest that LpRpoS may employ a distinct mechanism to recruit alternative regulatory factors controlling transcription initiation.

This research work deals with the formulation of numerical scheme with algorithm to compute singularly perturbed partial differential equations(SP-PDEs) involving a significant negative shift. The problem involves small parameter which causes a rapidly changing boundary layers in the vicinity of a body, and the negative shift term causes interior layer. Such appearance of an abruptly varying layers causes difficulties to find the exact solution and it is not adequate to employ classical numerical methods. The technique presented in this research work simplifies these challenges and yields accurate numerical solution.The stability and convergence analyses of the methods are examined and proven. To test the developed technique, numerical experiments are carried out and confirmed with theoretical analysis.

The overlap of visual items in data visualization techniques is a known problem aggravated by data volume and available visual space issues. Several methods have been applied to mitigate occlusion in data visualizations, such as Random Jitter, Transparency, Layout Reconfiguration, Focus+Context Techniques, etc. This paper aims to present a comparative study to read visual variables values with partial overlap. The study focuses on categorical data representations varying the percentage limits of partial overlap and the number of distinct values for each visual variable: Hue, Lightness, Saturation, Shape, Text, Orientation, and Texture. A computational application generates random scenarios for a unique visual pattern target to perform location tasks. Each scenario presented the visual items in a grid layout with 160 elements (10 x16), each visual variable had from 3 to 5 distinct values encoded, and the partial overlap percentage applied, represented by a gray square in the center o each grid element, were 0% (control), 50%, 60%, and 70%. Similar to the preliminary tests, the tests conducted in this study involved 48 participants organized into four groups, with 126 tasks per participant, and the application captured the response and time for each task performed. The result analysis indicates that the Hue, Lightness, and Shape visual variables are robust to high percentages of occlusion and gradual increase in encoded visual values. The Text visual variable show promising results for accuracy, and resolution time was a bit higher than the last visual variables mentioned. In contrast, the Texture visual variable presented lower accuracy to high levels of occlusion and more different visual encoding values. At last, the Orientation and Saturation visual variables got the highest error and worst perfomance rates during the tests.

Acrylamide is probably carcinogenic to humans (International Agency for Research on Cancer, group 2A) with major occurrence in heated, mainly carbohydrate-rich foods. For roasted coffee, a European Union benchmark level of 400 µg/kg acrylamide is of importance. Regularly, the acrylamide contents are controlled using liquid chromatography combined with tandem mass spectrometry (LC-MS/MS). This reference method is reliable and precise but laborious because of the necessary sample clean-up procedure and instrument requirements. This research investigates the possibility of predicting the acrylamide content from proton nuclear magnetic resonance (NMR) spectra that are already recorded for other purposes of coffee control. In the NMR spectrum acrylamide is not directly quantifiable, so that the aim was to establish a correlation between the reference value and the corresponding NMR spectrum by means of a partial least squares (PLS) regression. Therefore, 40 commercially available coffee samples with already available LC-MS/MS data and NMR spectra were used as calibration data. To test the accuracy and robustness of the model and its limitations, 50 coffee samples with extreme roasting degrees and blends were additionally prepared as test set. The PLS model shows an applicability for the varieties C. arabica and C. canephora, which were medium to very dark roasted using drum or infrared roasters. The root mean square error of prediction (RMSEP) is 79 µg/kg acrylamide (n=32). The PLS model is judged as suitable to predict the acrylamide values of commercially available coffee samples. On the other hand, very light roasts containing more than 1000 µg/kg acrylamide are currently not suitable for PLS prediction.

In this paper it is shown that mathematical description of strain, constitutive law and dynamics obtained by direct replacement of integer order derivatives with Caputo or Riemann-Liouville fractional order partial derivatives, having integral representation on finite interval, in case of a guitar string, is nonobjective. The basic idea is that different observers, using this type of descriptions, obtain different results which cannot be reconciled, i.e. transformed into each other using only formulas that link the coordinates of the same point in two fixed orthogonal reference frames and formulas that link the numbers representing the same moment of time in two different choices of the origin of time measuring. This is not an academic curiosity! It is rather a problem: which one of the obtained results is correct?

This study focuses on the impact of weak partial discharges (PDs) on defect recognition accuracy in epoxy resin through phase-resolved partial discharge (PRPD) analysis. Two measurement conditions are compared until PRPD pattern saturation: one-minute and one-hour durations. The PD data specifically target three void types located at different positions within the epoxy material. The aim is to evaluate how the presence of weak PDs at the PD extinction voltage (PDEV) influences defect recognition accuracy. This research sheds light on the potential implications of neglecting the significance of weak PD signals in defect detection. A convolutional neural network (CNN) model is trained using PRPD data recorded at the PD inception voltage (PDIV) and tested using the new PRPD data from both conditions recorded from a lower PDIV to a PDEV. The trained CNN model achieves a defect recognition accuracy of 100% for a one-hour duration, highlighting the importance of not neglecting weak PD signals. This emphasizes the significance of extended measurement duration and pattern saturation in capturing and analyzing weak PD signals for improved defect recognition. This study contributes to the advancement of practical applications by understanding the behavior of the epoxy material and enhancing defect detection techniques.

The members of the Liliaceae family have been regarded as an excellent source of biologically active compounds. However, the work on antimicrobial potential and characterization of the bioactive fractions of Lilium philadelphicum flower is limited and needs to be explored. The present study reports the antimicrobial potential, anti-inflammatory and anticancer potential of the bioactive fraction extracted from the flower of L. philadelphicum (Red Lily) and characterization of these bioactive compounds. The antimicrobial activity was tested against nine different Gram-positive and Gram-negative bacterial strains. The minimum inhibitory concentration (MIC) values of methanolic extract of L. philadelphicum flower against Acinetobacter bouvetii, Achromobacter xylosoxidans, Bacillus subtilis MTCC 121, Candida albicans MTCC 183, Klebsiella pneumoniae MTCC 3384, and Salmonella typhi MTCC 537 were 25, 50, 12.5, 50, 100 and 50 μg mL-1, respectively. The phytochemical analysis of the extract reveals the presence of phenols, flavonoids, tannins, terpenoids, glycosides, coumarins, and quinones. The cytotoxicity of the partially purified compound against the HepG2 cell line in MTT assay demonstrates up to 90% cell viability with a bioactive compound concentration of 50 μg/ml. However, with the increase in bioactive compound concentration up to 1000 μg/ml results into nearly 80% cell viability, just a minor decline in cell viability suggests the importance of bioactive compounds for suitable therapeutic applications. Spectroscopic studies of the bioactive compound by UV-Visible spectroscopy, FT-Infra Red spectroscopy, Gas Chromatography-Mass Spectrometry (GCMS) as well as its phytochemical analysis suggests the presence of terpenoids moiety, responsible for the antimicrobial property of L. philadelphicum flower.

Water resources worldwide are limited, especially in desert areas like Saudi Arabia. Therefore, the rational and sustainable management of irrigation water supply is an imperative required by the conditions of space and time. This study evaluates the irrigation system through partial root-zone drying (PRD) and regulated deficit irrigation (RDI). The effect of applying the PRD and RDI systems on the efficiency and rationalization of irrigation water consumption in a greenhouse and open field cucumber was studied in addition to using the surface (S) and subsurface (SB) drip irrigation methods on irrigation efficiency. The productivity of the RDI-S regular drip irrigation treatment was considered 100% as the control on which the results of all treatments are measured. The results showed that in terms of irrigation technique, the PRD-SB technique had the highest productivity during the winter season in greenhouse cucumbers, with a general average of 13.8 kg m-2 for all irrigation levels, while the RDI-SB technique had the highest productivity during the summer season, with a general average of 16.1 kg m-2. Regarding irrigation level results, the study showed that an irrigation level of 100% is the highest productivity in all irrigation techniques, with a general average of 14.9 kg m-2 for all irrigation techniques during the winter season and 16.4 kg m-2 during the summer. However, the increase in the irrigation level to 150% did not increase productivity. In comparison, the application of the deficit irrigation technique by reducing the level of irrigation to 50% was not accompanied by a similar decrease in productivity. The study results also showed that irrigation with the PRD-SB system was the most productive in the open field at all irrigation levels, with a general average of 7.3 kg m-2. The general average of the percentage decrease in productivity in all irrigation techniques compared to reducing the irrigation percentage to 50% and 75% was 22% and 3 %. The irrigation efficiencies were higher when applying the PRD (PRD-SB) in winter. In contrast, applying a deficit irrigation system (RDI-SB) in the summer season had the highest efficiency. It could be concluded that using PRD and RDI systems for indoor and outdoor cucumber can save irrigation water.

Partial negative allosteric modulators (NAM) of the mGlu5 receptor are an excellent alternative to full antagonists and NAMs because they retain some therapeutic effects and, at the same time, have a much broader therapeutic window. Here, we investigated whether partial mGlu5 NAM, M-5MPEP induced a fast and sustained antidepressant-like effect, characteristic of rapid-acting antidepressant drugs (RAADs) like ketamine, in C57BL/6J mice. M-5MPEP caused a rapid, dose-dependent antidepressant-like action in the tail suspension test (TST) 60 min after injection. This effect was antagonized by an AMPA receptor antagonist (NBQX) and a TrkB receptor antagonist (ANA-12) but not by 5HT1A and 5HT2A/2C receptor antagonists. Furthermore, M-5MPEP (30 mg/kg) induced sustained antidepressant-like effects 24 h after the last of four administrations. These effects were revealed in the splash test, designed to measure apathy-like state, and in the TST. Western blot and ELISA analyses indicated the involvement of the TrkB/BDNF pathway in the sustained M-5MPEP effects. Additionally, prolonged effects of M-5MPEP were entirely reversed by the TrkB receptor antagonist ANA-12 in both the splash test and the TST, confirming the critical role of TrkB receptor activation in the sustained antidepressant-like effect of M-5MPEP. Importantly, M-5MPEP enhanced the subthreshold dose of (R)-ketamine in the TST, indicating both substances' convergent mechanisms of action and the possibility of their practical use in treating depression.