Tablets are the most used solid dosage form in medical treatments. The realistic modeling 1 of such specific object shapes in computer simulations has been demonstrated already by the author 2 for bi-convex round tablets but needs to be extended for a wider range of tablet shapes. Moreover, 3 the number of tablets must be large enough to simulate industrial drum coaters, which are typically 4 used for film coating processes. Whilst this long lasting process where tablets flow continuously, 5 tablets are loaded by frequent changes of individual contacts. Using a tailored simulation tool named 6 pharmAssist , written for GPUs (modern massively parallel processors in graphics cards and HPC 7 accelerators), we implemented the widely used oblong tablet shape. We are able to simulate flows 8 involving industrial scale number of such tablets. Data mining allows for statistical analyzis of 9 pair-wise contacts of different geometric features. Our simulation results serves as an observation 10 space, which cannot be addressed by experimental analyzis and will help to avoid degradation of 11 tablets like chipping or other defect phenomena. This paper reflects current development work in 12 order to extend the DEM with a new shape class, which comprises the modelling of compacted or 13 extruded objects, which have a smooth exterior, a flat band and sharp contour edges

Spectral photon counting cone-beam CT imaging is challenged by individual pixel response behaviour, which leads to noisy projection images and subsequent image artefacts like rings. Existing methods to correct for this either use calibration measurements, like signal-to-thickness calibration (STC), or perform post-processing ring artefact correction of sinogram data or scan reconstructions, without taking the pixel response explicitly into account. Here we present a novel post-processing method (DAC-shifting), which explicitly measures the current pixel response using flat field images, and subsequently corrects the projection data. The DAC-shifting method was evaluated with a repeat series of spectral photon counting imaging (Medipix3) of a phantom with different density inserts, and in iodine K-edge imaging. The method was also compared against PMMA based STC. The DAC-shifting method was shown to be effective in correcting individual pixel response, and was robust against detector instability. On the contrary, STC correction showed varying results, which was almost as good as DAC-shifting when data was acquired just after STC calibration, but worse with larger time differences. In K-edge imaging, DAC-shifting provides a sharper attenuation peak, and more uniform CT values, which is expected to benefit iodine concentration quantification.

The applicability of the distance aggregation problem has attracted the interest of many authors. Motivated by this fact, in this paper we face the modular quasi-(pseudo-)metric aggregation problem. We characterize those functions that allow merging a collection of modular quasi-(pseudo-)metrics into a single one. Specifically, a description of such functions in terms of triangle triplets is given and, in addition, the relationship between modular quasi-(pseudo-)metric aggregation functions and modular (pseudo-)metric aggregation functions is discussed. Such characterizations are illustrated with appropriate examples. A few methods to construct modular quasi-(pseudo-)metrics are yielded. Several properties of modular quasi-(pseudo-)metric aggregation functions are explored and used to develop quick tests for discarding candidate functions to aggregate modular quasi-(pseudo-)metrics. Moreover, a characterization of those modular quasi-(pseudo-)metric aggregation functions that preserve modular quasi-(pseudo-)metrics is also provided. Furthermore, the relationship between modular quasi-(pseudo-)metric aggregation functions and quasi-(pseudo-)metric aggregation functions is studied in such a way that significative differences are displayed.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

Timber-concrete composite (TCC) systems join the positive aspects of engineered wood products (good seismic behaviour, low thermal conductivity, environmental sustainability, good behaviour under fire if appropriately designed) with those of concrete (high thermal inertia, durability, excellent fire resistance). TCC facades are typically composed by an internal insulated timber-frame wall and an external concrete slab, separated by a ventilated air cavity. However, there is very limited knowledge concerning the performance of TCC facades, especially for what concerns their thermal behaviour. The present paper deals with the development and optimisation of a 2D CFD model for the analysis of TCC ventilated façades thermal behaviour. The model is calibrated and validated against the experimental data collected during the annual monitoring of a real TCC ventilated envelope in the north of Italy. Also, a new solver algorithm is developed to significantly speed up the simulation. The final model can be used for the time-efficient analysis and optimisation of the thermal performance of TCC ventilated facades, as well as other ventilated facades with external massive cladding, avoiding the expensive and time-consuming construction of mock-ups, or the use of comparably slow (conventional) CFD solvers that are less suitable for optimization studies.

Fiber aggregation in nanocomposites has an important effect on the macroscopic electrical performance. To quantitatively evaluate its effect, an index to characterize the degree of aggregation is imperative, and ideally it should have three features simultaneously, i.e., single-parametric, dimensionless and physically meaningful, applicable to different aggregation topologies, and one-to-one corresponding to material electrical properties. To this end, a new aggregation degree is proposed, which is defined as the average increased number of fibers that connect with each one when fibers aggregate from a uniformly distributed state. This index is applicable to different aggregation topologies from lump-like aggregating clusters to network-like aggregating clusters. This index is proven to only depend on the local features of aggregating clusters, and can be concisely expressed by the characteristic parameters of local structure, via geometric probability analysis and numerical validations. Further, a one-to-one linear relation between the aggregation degree and percolation threshold is established by Monte Carlo simulations, which is independent of the distribution law of the fibers. This work provides a guide to the property characterization, performance prediction and material design of nanocomposites, and also gives a physical insight into the understanding of systems with similar non-uniform distributions.

The control of the fine particle emission from the coal-fired power plants has been a big challenge in china. Either the conventional electrostatic precipitator or the fabric filter has some shortages. The electrostatic precipitator is hard to keep high efficiency for the submicron particles. The fabric filter could keep high efficiency but with very high pressure drop. One solution is to combine them together. Several types of hybrid particle collectors (HPC) combining the electrostatic precipitator and the fabric filter together have been developed and applied in a number of projects in China. In recent years, numerical simulation technology has been widely used in the design of the collectors. In this paper, an unsteady numerical model is used to investigate the particle deposition characteristics in a scale hybrid collector. The fluid field is modeled by using incompressible Navier-Stokes equations with the RNG turbulence equations. The corona discharge is solved by using a finite volume method. The particle charging is modeled by using a filed-diffusing combined model. And an unsteady cake formation model is used to simulate the filtration process.

This work presents the results regarding the synthesis of tungsten nanoparticles (W NPs) by magnetron sputtering combined with gas aggregation (MSGA) when H2 mixed with Ar is used as working gas, the amount of H2 being increased up to 82%. The results show that up to 40% H2 in discharge the synthesis rate increases over 60 times, rapidly decreasing for over 50% H2 in discharge. The W dust is still produced in H2 dominated discharge (82%), the deposition rate being small but not negligible (20 mg/hour). The obtained WNPs are isolated, with the diameter decreasing from 50 nm to 15 nm when the amount of H2 in discharge is smaller than 41%. Over this value, the particles tend to agglomerate, forming structures similar to film-like deposits. Also, the diameter of the deposited spots on substrates is dependent on the H2 content in discharge. This allows the efficient coating of substrates with dimensions up to 26 mm by translating them in front of the MSGA cluster source exit aperture. Supplementary, for 41% H2 in discharge, the influence of synthetic air leaks (0-5%) in discharge was investigated. The deposition rate decreases rapidly (ceasing for around 4% air in discharge) and the obtained nanoparticles tend to agglomerate (at 2% air content, the dust deposit has the aspect of a near continuous film). Chemical composition investigations show a pronounced tendency of oxidation, nitridation and oxynitride formation in the presence of air leaks.

Asphaltene is a component of crude oil that, if mishandled, may create substantial transportation and industrial concerns. It is a solid by nature, with a diverse set of molecular compositions. Furthermore, the oil industry has identified emulsion generation and clogging precipitate as key concerns. The emulsified water droplets in the process are just what give the raw oil its increased viscosity; hence, power is squandered to transport the oil around. The information has been separated into sections based on simulation, solubilization, agglomeration, precipitation, and evidence of model chemicals in the literature. We have included research that investigates the bulk rheology and interfacial rheology of asphaltene to describe its interfacial activity more clearly.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

The Fuzzy Transportation Problem (FTP) represents a significant extension of the Classical Transportation Problem (TP) by introducing uncertainly and imprecision into the parameters involved. Various algorithms have been proposed to solve the FTP, including fuzzy linear programming, metaheuristic algorithms and fuzzy mathematical programming techniques combined with Artificial Neural Networks. This paper presents the application of Trigonometric Acceleration Coefficients-PSO (TrigAc-PSO), a variation of the Classical Particle Swarm optimization algorithm, which is an innovative algorithm originally developed for solving the TP. TrigAC-PSO, has demonstrated remarkable success in optimizing various problem domains in crisp environments.

Background: The antisense oligonucleotide against APOC3 mRNA volanesorsen was recently introduced to treat Familial Chylomicronemia Syndrome (FCS). Cases of decreased platelet count are reported among patients treated with volanesorsen. The aim of the study is to evaluate platelet function and thrombin generation (TG) assessment in FCS patients receiving volanesorsen. We performed a cross-sectional study on FCS patients treated with volanesorsen. Methods: changes in PLC were assessed from baseline to Tw12 and Tw36. To assess TG, samples were processed by CAT (with PPP-reagent LOW). The results were expressed by the trombogram graphic (thrombin variation over time); lagTime; Endogenous Thormbin Potential(ETP); peak; time to reach peak(ttpeak), startTail e velocity Index. Platelet aggregation was assessed by testing different agonists using turbidimetry method. Results: Four FCS patients and 4 matched healthy controls were included in the present study. Changes in PLC at Tw12 was 30% and 34% at T36w. Thrombin generation results show values in normal range (for patients and controls respectively lagTime:10,42±4,40 and 9,25±0,99; ttPeak:14,33± 4,01 and 13,10±0,67; startTail:32,13±3,54 and 29,46±1,69; velocityIndex:20,21±3,63 and 33,05±13,21; ETP 599,80±73,47 and 900,2±210,99; peak value 76,84±1,07 and 123,30±39,45) and no significant difference between cases and controls. Platelet aggregation test showed values in range with no significant difference with healthy controls Conclusions: Our study showed for the first time that no significant changes in the general haemostasis assessed by TG and in platelet function have been observed in FCS patients receiving volanesorsen.

Advanced glycation end-products (AGEs) form through non-enzymatic glycation of various proteins. Optic nerve degeneration is a frequent complication of diabetes, and retinal AGEs accumulation is strongly linked to diabetic retinopathy development. Type 2 diabetes mellitus (T2DM) is a major risk factor for Alzheimer's disease (AD), with patients often exhibiting optic axon degeneration in the nerve fiber layer. Notably, a gap exists in our understanding of how AGEs contribute to neuronal degeneration in the optic nerve within the context of both diabetes and AD. Our previous work demonstrated that glyceraldehyde (GA)-derived toxic advanced glycation end-products (TAGE) disrupt neurite outgrowth through TAGE-β-tubulin aggregation and tau phosphorylation in neural cultures. In this study, we further illustrated GA-induced suppression of optic nerve axonal elongation via abnormal β-tubulin aggregation in mouse retinas. Elucidating this optic nerve degeneration mechanism holds promise for bridging the knowledge gap regarding vision loss associated with DM and AD.

Tailings generated by mining account for the largest proportion of global waste from industrial activities. Copper is relatively uncommon world-wide, with low concentrations in sediments and waters, yet is very elevated around mining sites. On the Keweenaw Peninsula of Michigan, USA, jutting out into Lake Superior, 140 mines extracted native copper from the Portage Lake Volcanic Series, part of an intercontinental rift system. Between 1901-1932, two mills at Gay (Mohawk, Wolverine) sluiced 22.7 million metric tonnes (MMT) of copper-rich tailings (stamp sands) into Grand (Big) Traverse Bay. Here we examine: 1) 3D coastal elevation and reef bathymetry, 2) particle dispersal, 3) copper concentrations and leaching, plus 4) shoreline toxicity. About 10 MMT of tailings created a migrating coastal beach that stretches 7 km from the Gay pile to the Traverse River Seawall. Another 10 MMT are moving underwater on the coastal shelf, threatening Buffalo Reef, an important lake trout and whitefish breeding ground. Aerial photos, ALS (plane) LiDAR, and relatively inexpensive UAS (drone) surveys characterize shoreline structure and aid initial remediation. Because sands (natural beach quartz, stamp sand basalt) are silicates of similar density, particle dispersal is similar and challenging. However, stamp sand beaches contrast greatly with natural sand beaches in both physical profile and chemistry. Dispersing particles retain copper, and release toxic concentrations. Leaching is elevated by exposure to high DOC and low pH waters. Field experiments, shoreline seining, and benthic sampling confirm serious impacts on aquatic biota, supporting tailings removal.

This review article is devoted to the colloidal properties of fullerene solutions. According to generally accepted understanding, all solvents in relations to fullerenes are divided into “good” (or “strong” or “high-solubility” ones), “poor” (usually polar) and “reactive”. Water occupies a special place, close to “poor” solvents. We have consistently considered and discussed the state of fullerenes in these systems. In "good", predominantly non-polar aromatic solvents and CS2, nonequilibrium dissolution methods lead to the formation of colloidal aggregates, whereas utilization of equilibrium methods results in the formation of molecular solutions. The latter, however, have some unusual properties; new results confirm previously expressed ideas about colloidal properties of these solutions. Both experimental and theoretical methods devoted to such systems are considered. In “poor” (polar) solvents, typical lyophobic colloidal systems appear. Both “bottom-up” and “top-down” methods of preparation are now well documented in the literature. However, some of these polar solvents dissolve fullerenes rather easily and with less energy consumption. In addition to N-methylpyrrolidin-2-one, which has been well studied for fullerenes, DMSO and DMF have now been described. These solvents can be considered a subset of poor solvents that have some features of being “reactive” at the expense of basic (“cationophilic”) properties. Room temperature ionic liquids are also used to dissolve fullerenes, but there is little experimental research. Hydrosols and aqueous suspensions of fullerenes are typical hydrophobic colloids that obey the Schulze–Hardy rule and other regularities in the presence of electrolytes. New experimental data confirm the previously obtained results. Organosols in acetonitrile and methanol are much less stable with respect to electrolytes; the difference in critical coagulation concentrations of electrolytes reaches two to three orders of magnitude. This allows us to conclude that there is an additional, so-called non-DLVO, stabilizing factor in the hydrosols. Accordingly, the value of the Hamaker constant of fullerene-fullerene interaction may be higher than that derived from coagulation data in water. Contrary to the mentioned “poor” polar solvents, the stability of fullerene sols in DMSO is even higher than in water. These results, as well as data obtained with DMF demonstrate strong solvation of fullerenes with basic solvents.

With the growing demand for positioning services, angle-of-arrival (AoA) estimation or direction-finding (DF) has been widely investigated for applications in fifth-generation (5G) technologies. Many existing AoA estimation algorithms only require the measurement of the direction of the incident wave at the transmitter to obtain correct results. However, for most of the cellular systems such as Bluetooth indoor positioning system due to multipath and non-line-of-sight (NLOS) propagation, the indoor positioning accuracy is severely affected. In this paper a comprehensive algorithm is investigated that combines radio measurements from Bluetooth AoA local navigation systems with indoor position estimates obtained using particle filtering, which allows us to explore new optimised methods to reduce estimation errors in indoor positioning. First, particle filtering is used to predict the rough position of a moving target. Then, an algorithm with robust beam weighting is used to estimate the AoA of the multipath components. Based on this, a system of pseudo-linear equations for target positioning based on the probabilistic framework of PF and AoA measurement is derived. Theoretical analysis and simulation results show that the algorithm can improve the positioning accuracy by about 25.7% on average.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

Platelet P2Y₁₂ is an important ADP receptor that is involved in agonist-induced platelet aggregation and is a valuable target for the development of anti-platelet drugs. Here we characterise the effects of thio-analogues of uridine triphosphate (UTP) on ADP-induced platelet aggregation. Using human platelet-rich plasma we demonstrate that UTP inhibits P2Y₁₂ but not P2Y₁ receptors and antagonises 10 μM ADP-induced platelet aggregation in a concentration-dependent manner with an IC₅₀ value of ~250 μM. An 8-fold higher platelet inhibitory activity was observed with a 2-thio analogue of UTP (2S-UTP), with an IC₅₀ of 30 μM. The 4-thio analogue (4S-UTP) with an IC₅₀ of 7.5 μM was 33-fold more effective. A 3-fold decrease in inhibitory activity, however, was observed by introducing an isobutyl group at the 4S- position. A complete loss of inhibition was observed with thio-modification of the γ phosphate of the sugar moiety, which yields an enzymatically stable analogue. The interaction of UTP analogues with P2Y₁₂ receptors was verified by P2Y₁₂ receptor binding and cAMP assays. These novel data demonstrate for the first time that 2- and 4-thio analogues of UTP are potent P2Y₁₂ receptor antagonists that may be useful for therapeutic intervention.

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (<0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (>2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.

Amyloids result from the aggregation of several unrelated proteins, due to either specific mutations or promoting intra- or extra-cellular conditions. Structurally, they are rich in intermolecular β-sheets and are the causative agents of several diseases, both neurodegenerative and systemic. It is believed that the most toxic species are small aggregates, referred to as oligomers, rather than the final fibrillar assemblies. Their mechanisms of toxicity are mostly mediated by aberrant interactions with the cell membranes, with resulting derangement of membrane-related functions. Much effort is being put in the search for natural antiamyloid agents, and/or in the development of synthetic molecules. Actually, it is well documented that the prevention of amyloid aggregation results in several cytoprotective effects. Here, we portray the state of the art in the field. Several natural compounds are effective antiamyloid agents, notably tetracyclines and polyphenols. They are generally non-specific, as documented by their partially overlapping mechanisms, and the capability to interfere with the aggregation of several unrelated proteins. Among rationally designed molecules, we mention the prominent examples of β-breakers peptides, whole antibodies and fragments thereof, and the special case of drugs contrasting transthyretin aggregation. In this framework, we stress the pivotal role of the computational approaches. When combined with biophysical methods, in several cases they have helped clarify in detail the protein/drug modes of interaction, which make it plausible that more effective drugs will be developed in the future.

While the standard model accurately describes data at the electroweak scale without inclusion of gravity, beyond the standard model physics is increasingly intertwined with gravitational phenomena and cosmology. Thus gravity mediated breaking of supersymmetry in supergravity models lead to sparticles masses, which are gravitational in origin, observable at TeV scales and testable at the LHC, and supergravity also provides candidate for dark matter, a possible framework for inflationary models and for models of dark energy. Further, extended supergravity models, and string and D-brane models contain hidden sectors some of which may be feebly coupled to the visible sector resulting in heat exchange between the visible and hidden sectors. Because of the couplings between the sectors both particle physics and cosmology are effected. The above implies that particle physics and cosmology are intrinsically intertwined in the resolution of essentially all of the cosmological phenomena such as dark matter and dark energy and in the resolution of cosmological puzzles such as Hubble tension and EDGES anomaly. Here we give a brief overview of the intertwining and implications for the discovery of sparticles, and the resolution of the cosmological anomalies and identification of dark matter and dark energy as major challenges for the coming decades.

Candida albicans is an opportunistic fungus that becomes pathogenic and problematic under certain biological conditions. C.albicans may cause painful and uncomfortable symptoms, as well as deaths in immunocompromised patients. Therefore, early detection of c.albicans is essential. However, conventional detection methods are costly, slow and inaccessible to women in remote or developing areas. To address these concerns, we have developed a wearable and discrete naked-eye detectable, colorimetric platform for c.albicans detection. With some modification, this platform is designed to be directly adhered to existing feminine hygiene pads. Our platform is rapid, inexpensive, user-friendly, disposable and only requires three steps: i) addition of vaginal fluid onto sample pads; ii) addition of gold nanoparticle gel and running buffer, and iii) naked eye detection. Our platform is underpinned by selective thiolated aptamer-based recognition of 1,3-β-D glucan molecules- a hallmark of c.albicans cell walls. In the absence of c.albicans, wearable sample pads turn bright pink. In the presence of c. albicans, the wearable pads turn dark blue due to significant nanoparticle target-induced aggregation. We demonstrate naked eye colorimetric detection of 4.4 ×106 c.albicans cells per ml. We believe that this proof-of-concept platform has the potential to have a significant impact on women’s health, globally.

Alzheimer’s disease is associated with prion-like aggregation of the amyloid β (Aβ) peptide and the subsequent accumulation of misfolded neurotoxic aggregates in the brain. Therefore, it is critical to clearly identify the factors that trigger the cascade of Aβ misfolding and aggregation. Numerous studies have pointed out the association between microorganisms and their virulence factors and Alzheimer’s disease; however, their exact mechanisms of action remain unclear. Recently, we discovered a new pathogenic role of bacterial extracellular DNA, triggering the formation of misfolded Tau aggregates. In this study, we investigated the possible role of DNA extracted from different bacterial and eukaryotic cells in triggering Aβ aggregation in vitro. Interestingly, we found that the extracellular DNA of some, but not all, bacteria is an effective trigger of Aβ aggregation. Furthermore, the acceleration of Aβ nucleation and elongation can vary based on the concentration of the bacterial DNA and the bacterial strain from which this DNA had originated. Our findings suggest that bacterial extracellular DNA might play a previously overlooked role in the Aβ protein misfolding associated with Alzheimer’s disease pathogenesis. Moreover, it highlights a new mechanism of how distantly localized bacteria can remotely contribute to protein misfolding and diseases associated with this process. These findings might lead to the use of bacterial DNA as a novel therapeutic target for the prevention and treatment of Alzheimer’s disease.

This study analyzes the correlation between the lifetime and the rest energy of the unstable particle states with a lifetime greater than the zeptosecond (10⁻²¹ s), using data available from the Particle Data Group. This set of states seems to be divided into three groups, in each of which the two quantities can be correlated through a remarkably accurate power law. Although this fact does not represent anything new compared to the predictions of the Standard Model, it nevertheless reveals an unexpected order structure in the set of particle decays, emerging from such predictions.

Plant biomass could become a new world-class "currency" because almost everything can be made of it: fuels, foods, feeds, constructing materials, furniture, etc. Currently, growing biomass for energy needs is particularly relevant in so complicated socioeconomical situation. There are important its productivity and the lowest possible ecological footprint. Can increasing crop biodiversity address these challenges? A field experiment was started at the Vytautas Magnus University Agricultural Academy in 2020-2022. Maize, hemp and faba bean were grown as single, binary and ternary crops to determine its effect on soil properties. Studies have shown that most intercrops failed to stabilize soil aggregate composition, NPK levels and pH, and enzyme urease activity. Binary maize-hemp and the ternary crops reduced the amount of the main macroelements in the soil the most because of the highest yields, which were removed from the fields. Regardless of the ecological services provided by faba beans, biomass removal leads to degradation of most soil properties and making the soil vulnerable to erosion. In the future, the cultivation of such multicrops should be investigated under conditions of more abundant fertilization or the effect of green manure should be used by increasing the number of fast- and short-growing interior plant species in the cultivation.

In this paper, we consider the formation of quantum black holes (QBHs) through a genuine quantum process. We treat particles at the Planck energy as QBHs. The Hawking temperature and entropy of QBHs are estimated. We also show that a QBH has a discrete energy spectrum. By analogy with supersymmetric theory, the mass of the superpartner of a QBH is estimated.

The air is not the same as thousands and hundreds of years ago. In the air, suspended particles originate from natural phenomena like dust storms or volcanic activities, as well as anthropogenic pollutants such as fuel engine exhaust and everyday activities at home. The total particles in the air can be classified by sizes, such as PM10, PM2.5 or ultrafine particles. However, there are many other important factors in addition to the particle size, influencing the particle behavior and affecting our health. The surface area, chemical and biological composition, aspect ratio, and the charge are all factors characteristic of particles. OoC microfluidic chips are very useful for the pollutant toxicity measurements on various body tissues. A better understanding of pollutants will help to trace these to the potential sources. The data from the on-the-ground and satellite monitoring can be integrated into models, helping to predict and prevent pollution exposure.

Utilizing lignocellulosic biosourced platforms, we synthesized novel cyanostilbene (CS) deriva-tives featuring the 3,4-dimethoxyphenyl moiety. These derivatives were investigated for their emission properties in both solution and solid states. The two simple CS derivatives exhibit very weak luminescence in solution but significant luminescence in the solid state, indicating distinct Aggregation-Induced Emission (AIE) characteristic. Furthermore, combining these two CS units, without conjugation and with quasi perpendicular orientation, results in Dual-State Emission (DSE) fluorophore showing luminescence both in solution and solid states. X-ray crys-tallography studies on the solid-state compounds reveal a structure-emission relationship, demonstrating that the colour emission correlates with the conformations adopted by the mol-ecules in the solid state, which influence the type of stacking.

Due to the uniqueness of the underwater environment, traditional data aggregation schemes face many challenges. Most existing data aggregation solutions do not fully consider node trustworthiness, which may result in the inclusion of falsified data sent by malicious nodes during the aggregation process, thereby affecting the accuracy of the aggregated results. Additionally, because of the dynamically changing nature of the underwater environment, current solutions often lack sufficient flexibility to handle situations such as node movement and network topology changes, significantly impacting the stability and reliability of data transmission. To address the aforementioned issues, this paper proposes a secure data aggregation algorithm based on a trust mechanism. By dynamically adjusting the number and size of node slices based on node trust values and transmission distances, the proposed algorithm effectively reduces network communication overhead and improves the accuracy of data aggregation. Due to the variability in the number of node slices, even if attackers intercept some slices, it is difficult for them to reconstruct the complete data, thereby ensuring data security.

Centralized/Cloud Radio Access Networks (C-RAN) are deployed in converged fixed-mobile networks to exploit the flexibility coming from joint application of Network Function Virtualization (NFV) and Software Defined Networking (SDN). In this context, optical links connecting C-RAN nodes, possibly based on the Ethernet standards, may carry traffic with different requirements in terms of latency and throughput. This paper considers the problem of traffic aggregation on C-RAN optical Ethernet links with latency control for fronthaul traffic and throughput capability for backhaul traffic. Integrated hybrid nework technique is applied to show how time transparency can be enforced for Ethernet encapsulated Common Public Radio Interface (CPRI) traffic while allowing statistical multiplexing of backhaul traffic. Simulation results show the effectiveness of segmentation of backhaul traffic to allow exploitation of the available bandwidth even with high capacity CPRI options.

Neurodegenerative diseases, including Alzheimer's, Huntington's, Parkinson’s, and Amyotrophic Lateral Sclerosis, involve neuron degeneration linked to the misfolding of amyloidogenic proteins, resulting in β-sheet-enriched aggregates. This phenomenon disrupts the normal folding of proteins critical for cellular function. Genetic mutations, proteolytic cleavage, oxidative stress, and aging contribute to misfolding. Parkinson's disease (PD) is closely tied to alpha-synuclein (αS) misfolding, with A53T mutation and Lewy bodies (LB) in PD brains pivotal to understanding the disease mechanism. Other synuclein homologues (βS, γS) further contribute to synucleinopathies. Mutants (A30P, A53T, E46K, H50Q, and G51D) underscore αS's role in PD development. This concise review focuses on molecular and pathological aspects of neurodegenerative diseases, emphasizing αS in PD. The integration of genetic, structural, and mechanistic insights highlights the disorders. complexity, paving the way for future therapeutic strategies targeting protein misfolding and aggregation.

We investigate the Friedmann–Lemaitre–Robertson–Walker cosmological models within the framework of Rastall gravity incorporating particle creation. The modified field equations for Rastall gravity are derived and exact solutions are obtained under various choices of scale factors. The qualitative behaviour of our solutions depends on the Rastall coupling parameter ψ=kλ. Following the literature, we have restricted the Rastall coupling parameter ψ(k=1) to the range −0.0001 < ψ < 0.0007 at 68% CL from CMB+BAO data. Further, we have discussed the distinct physical behaviour of the derived models in detail.

Fake news detection has become a significant topic based on the fast-spreading and detrimental effects of such news. Many methods based on deep neural networks learn clues from claim content and message propagation structure or temporal information, which have been widely recognized. However, such models (i) ignore the fact that information quality is uneven in propagation, which makes semantic representations unreliable. (ii) Most models do not fully leverage spatial and temporal structure in combination. (iii) Finally, internal decision-making processes and results are non-transparent and unexplained. In this study, we develop a trust-aware evidence reasoning and spatiotemporal feature aggregation model for more interpretable and accurate fake news detection. Specifically, we first design a trust-aware evidence reasoning module to calculate the credibility of posts based on a random walk model to discover high-quality evidence. Next, from the perspective of spatiotemporal structure, we design an evidence-representation module to capture the semantic interactions granularly and enhance the reliable representation of evidence. Finally, a two-layer capsule network is designed to aggregate the implicit bias in evidence while capturing the false portions of source information in a transparent and interpretable manner. Extensive experiments on two benchmark datasets indicate that the proposed model can provide explanations for fake news detection results, as well as can achieve better performance, boosting 3.5% in F1-score on average.

Identifying fake news on the media has been an important issue. This is especially true considering the wide spread of rumors on the popular social networks such as Twitter. Various kinds of techniques have been proposed for automatic rumor detection. In this work, we study the application of graph neural networks for rumor classification at a lower level, instead of applying existing neural network architectures to detect rumors. The responses to true rumors and false rumors display distinct characteristics. This suggests that it is essential to capture such interactions in an effective manner for a deep learning network to achieve better rumor detection performance. To this end we present a simplified aggregation graph neural network architecture. Experiments on publicly available Twitter datasets demonstrate that the proposed network has performance on a par with or even better than that of state-of-the-art graph convolutional networks, while significantly reducing the computational complexity.

The multidrug-resistant fungal pathogens belonging to the Candida haemulonii complex and the phylogenetically related species Candida auris are well-known for causing infections that are difficult to treat due to their multidrug-resistance profile. C. auris is even more worrisome due to its ability to cause outbreaks in healthcare settings. These emerging yeasts produce a wide range of virulence factors that facilitate the development of the infectious process. In recent years, the aggregative phenotype has been receiving attention, as it is mainly associated with defects in cellular division and its possible involvement in helping the fungus to escape from host immune responses. In this study, we initially investigated the aggregation ability of 18 clinical isolates belonging to the C. haemulonii species complex and C. auris. Subsequently, we evaluated the effects of physicochemical factors on the fungal aggregation competence. The results demonstrated that cell aggregation was a typically time-dependent event, in which almost all studied fungal isolates exhibited high aggregation after 2 h of incubation at 37°C. The aggregation was not impacted by pH, temperature, -mercaptoethanol (a protein-denaturing agent) and EDTA (a chelator agent). Conversely, proteinase K, trypsin and sodium dodecyl sulfate significantly diminished the aggregation. Collectively, our results demonstrated that the aggregation ability in these opportunistic yeast pathogens is time-dependent, and surface proteins and hydrophobic interactions seem to mediate cell aggregation, since the presence of proteases and anionic detergent affected the aggregation ability. However, further studies are necessary to better elucidate this phenomenon.

Information Technology (IT) has become an essential part of our lives and due to the emergence of Internet-of-Things (IoT), technology has encompassed a majority of things that humans rely on in their daily lives. Further, as IT becomes more relevant in daily lives, the need for IT to serve public emergency services has become more important. However, due to the infancy status of IoT, there is a need for a data consortium that would prove to be best used in servicing policing in a technological driven society. This paper will discuss the plausibility of creating a universal format for use in carrying out public services, such as emergency response by the police and regular law maintenance. In this research we will discuss what the police requires in their line-of-duty and how smart devices can be used to satisfy those needs. A data formatting framework is developed and demonstrated, with the goal of showing what can be done to unifying data from smart city sensors.

The purpose of this paper is twofold. First, we introduce a geometric approach to study the circular orbit of a particle in static and spherically symmetric spacetime based on Jacobi metric. Second, we apply the circular orbit to study the weak gravitational deflection of null and time-like particles based on Gauss-Bonnet theorem. By this way, we obtain an expression of deflection angle and extend the study of deflection angle to asymptotically non-flat black hole spacetimes. Some black holes as lens are considered such as a static and spherically symmetric black hole in the conformal Weyl gravity and a Schwarzschild-like black hole in bumblebee gravity. Our results are consistent with the previous literature. In particular, we find that the connection between Gaussian curvature and the radius of a circular orbit greatly simplifies the calculation.

Epidermal growth factor (EGF) repeats are present in various proteins and form well-defined structures with three disulfide bonds. One representative protein is the Notch receptor. Each EGF repeat contains unique atypical O-linked glycans such as O-linked N-acetylglucosamine (O-GlcNAc). To generate a monoclonal antibody against the O-GlcNAc moiety in mouse Notch1, we expressed the recombinant C-terminal His6-tagged Notch1 EGF14-15 protein in HEK293T cells to prepare the immunogen. Most of the proteins were not secreted and showed higher molecular weight ladders in the cell lysate, suggesting protein aggregation. To overcome this issue, we fused Sparcl1 as an extracellular escorting tag to the N-terminus of Notch1 EGF14-15-His6. The fusion protein was efficiently secreted extracellularly without protein aggregates in the lysates. Following PreScission protease treatment, EGF14-15-His6 was efficiently released from the escorting tag. EGF14-15-His6 prepared using this method was indeed O-GlcNAcylated. The optimal length of the escorting tag was determined by generating deletion mutants to improve the extracellular secretion of EGF14-15-His6. Hence, a large amount of EGF14-15-His6 was successfully prepared from the culture supernatant of HEK293T cells, which were otherwise prone to aggregation.

As a novel concept in technology and communication world, “Internet of Things (IoT)” has been emerged. In such modern technology, the capability to transmit data through data communication networks (such as Internet or Intranet) is provided for each organism (e.g. human being, animals, things, and so forth). Due to the limited hardware and communication operational capability as well as small dimensions, IoT undergoes quite a few challenges. Such inherent challenges not only cause fundamental restrictions in the efficiency of aggregation, transmission, and communication between nodes; but they also degrade routing performance. To cope with the reduced availability time and unstable communications among nodes, data aggregation and transmission approaches in such networks are designed more intelligently. In this paper, a distributed method is proposed to set child balance among nodes. In this method, the height of the network graph is increased through restricting the degree; and network congestion is reduced as a result. Besides, a dynamic data aggregation approach -named as LA-RPL- is proposed for RPL networks. More specifically, each node is equipped with learning automata in order to perform data aggregation and transmissions. Simulation results demonstrate that the proposed approach outperforms previously suggested based approaches in terms of energy consumption, network control overhead, and packet loss rate.

The Pythagorean fuzzy set (PFS), which is characterized by a membership and a non-membership degree and the square sum of them is less or equal to one, can act as an effective tool to express decision makers’ fuzziness and uncertainty. Considering that the Heronian mean (HM) is a powerful aggregation operator which can take the interrelationship between any two arguments, we study the HM in Pythagorean fuzzy environment and propose new operators for aggregating interval-valued Pythagorean fuzzy information. First, we investigate the HM and geometric HM (GHM) under interval-valued intuitionistic fuzzy environment and develop a series of aggregation operators for interval-valued intuitionistic fuzzy numbers (IVIFNs) including interval-valued intuitionistic fuzzy Heronian mean (IVIFHM), interval-valued intuitionistic fuzzy geometric Heronian mean (IVIFGHM), interval-valued intuitionistic fuzzy weighted Heronian mean (IVIFWHM) and interval-valued intuitionistic fuzzy weighted geometric Heronian mean (IVIFWGHM). Second, some desirable and important properties of these aggregation operators are discussed. Third, based on these aggregation operators, a novel approach to multi-attribute decision making (MADM) is proposed. Finally, to demonstrate the validity of the approach, a numerical example is provided and discussed. Moreover, we discuss several real-world applications of these operators within policy-making contexts.

Satellite scene classification is challenging because of the high variability inherent in satellite data. Although rapid progress in remote sensing techniques has been witnessed in recent years, the resolution of the available satellite images remains limited compared with the general images acquired using a common camera. On the other hand, a satellite image usually has a greater number of spectral bands than a general image, thereby permitting the multi-spectral analysis of different land materials and promoting low-resolution satellite scene recognition. This study advocates multi-spectral analysis and explores the middle-level statistics of spectral information for satellite scene representation instead of using spatial analysis. This approach is widely utilized in general image and natural scene classification and achieved promising recognition performance for different applications. The proposed multi-spectral analysis firstly learns the multi-spectral prototypes (codebook) for representing any pixel-wise spectral data, and then based on the learned codebook, a sparse coded spectral vector can be obtained with machine learning techniques. Furthermore, in order to combine the set of coded spectral vectors in a satellite scene image, we propose a hybrid aggregation (pooling) approach, instead of conventional averaging and max pooling, which includes the benefits of the two existing methods but avoids extremely noisy coded values. Experiments on three satellite datasets validated that the performance of our proposed approach is much more accurate than even the deep learning framework for spatial analysis.

In this study, a novel theory to investigate the mass oscillation of particles is proposed. It has been proven that, at high-energy conditions, the fermion field described by Dirac’s Lagrangian interacts with the half-integer spin tachyon field with negative energy, causing the formation of composite particles whose mass depends on the total angular momentum. The proposed theory is based on a new interpretation of the Majorana equation for particles with arbitrary spin and shows that mass oscillation is a phenomenon in which the component of particle decay prevails over that of mixing mass states. Using the kinematic of Lemke for spacelike particle decay, we propose a mechanism able to explain the neutrino flavour change. The proposed mechanism is also investigated concerning the shape of its spectrum. Finally, the Lagrangian field of composite particles is formulated.

In the present study we tested the effect of small molecular weight redox molecules on collagen-induced platelet aggregation. We used N-acetylcysteine amide (AD4), the amide form of N-acetylcysteine (NAC), a thiol antioxidant with improved lipophilicity and bio-availability compared to NAC, and the thioredoxin mimetics (TXM) peptides, TXM-CB3, TXM-CB13, and TXM-CB30. All compounds significantly inhibited platelet aggregation induced by collagen, with TXM-peptides and AD4 being more effective than NAC. The levels of TxB2 and 12-HETE, the main metabolites derived from the cyclooxygenase and lipoxygenase pathways following platelet activation, were significantly reduced in the presence of AD4, TXM-peptides, or NAC, when tested at the highest concentration (0.6 mM). The effect of AD4, TXM-peptides, and NAC was tested also on the clotting time (CT) of whole blood. TXM-CB3 and TXM-CB30 showed the highest increase of CT. Furthermore, two representative compounds, TXM-CB3, and NAC, showed an increase in the an-ti-oxidant free sulfhydryl groups of plasma detected by Ellman’s method, suggesting a contribution of plasma factors to the antiaggregating effects. Our results suggest that these small molecular weight redox peptides might become useful for the prevention and/or treatment of oxidative stress conditions associated with platelet activation.

Meta-aminobenzoic acid, an important model system in the study of polymorphism and crystallization of active pharmaceutical ingredients, exist in water in both the nonionic (mABA) and zwitterionic (mABA^±) forms. However, the constituent molecules of the polymorph that crystallizes from aqueous solutions are zwitterionic. This study reports atomistic simulations of the events surrounding the early stage of crystal nucleation of meta-aminobenzoic acid from aqueous solutions. Ab initio molecular dynamics was used to simulate the hydration of mABA± and mABA, and to quantify the interaction of these molecules with the surrounding water molecules. Density functional theory calculations were conducted to determine the low-lying energy conformers of meta-aminobenzoic acid dimers and compute the Gibbs free energies in water of nonionic, (mABA)₂, zwitterionic, (mABA^±)₂ and nonionic-zwitterionic, (mABA)(mABA^±), species. Classical molecular dynamics simulations of mixed mABA–mABA^± aqueous solutions were carried out to examine the aggregation of meta-aminobenzoic acid. According to these simulations the selective crystallization of the polymorph which constituent molecules are zwitterionic is driven by the formation of zwitterionic dimers in solution, which are thermodynamically more stable than (mABA)₂ and (mABA)(mABA^±) pairs. This work represents a paradigm of the role of molecular processes during the early stages of crystal nucleation in affecting polymorph selection during crystallization from solution.

Single-particle inductively coupled plasma mass spectrometry (spICP-MS) has been used for particle size measurement of diverse types of individual nanoparticles and micrometer-sized carbon-based particles, such as microplastics. However, its applicability to the measurement of micrometer-sized non-carbon-based particles such as silica (SiO2) is unclear. In this study, the applicability of spICP-MS to particle size measurement of non-porous/mesoporous SiO2 micro-spheres with a nominal diameter of 5.0 µm or smaller was investigated. Particle sizes of these microspheres were measured using both spICP-MS based on a conventional calibration approach using an ion standard solution and scanning electron microscopy (SEM) as a reference technique and the results were compared. The particle size distributions obtained using both techniques were in agreement within analytical uncertainty. The applicability of this technique to the detection of metal-containing protein-binding mesoporous SiO2 microspheres was also investigated. Bound iron (Fe)-containing proteins (i.e., lactoferrin and transferrin) of mesoporous SiO2 microspheres were detected using Fe as a presence marker for the proteins. Thus, spICP-MS is applicable to the particle size measurement of large-sized and non-porous/mesoporous SiO2 microspheres; it has considerable potential for element-based detection and qualification of bound proteins of mes-oporous SiO2 microspheres in a variety of applications.

The supramolecular aggregation processes occurring on metallic (aluminum and gold) surfaces in aqueous solutions of bovine serum albumin (BSA) during drying were studied using advanced scanning electron microscopy (SEM). The possible mechanism for the formation of amazing intricate fractal structures on metallic surfaces was proposed based on the analysis of SEM images, size distribution diagrams and EDX-scanning elements distribution maps.

Coffee is rich in caffeine (CF), chlorogenic acid (CGA) and phenolics. Differing types of coffee beverages and brewing procedures may result in differences in total phenolic contents (TPC) and biological activities. Inflammation and increases of platelet activation and aggregation can lead to thrombosis. We focused on determining the chemical composition, antioxidant activity and inhibitory effects on agonist-induced platelet aggregation and cyclooxygenase (COX) of coffee beverages in relation to their preparation method. We prepared instant coffee and brewed coffee beverages using drip, espresso and boiling techniques. Coffee extracts were assayed for their CF and CGA contents using HPLC, TPC using colourimetry, platelet aggregation with an aggregometer and COX activity using ELISA. The findings have shown all coffee extracts, except the decaffeinated types, contained nearly equal amounts of CF, CGA and TPC. Inhibitory effects of coffee extracts on platelet aggregation differed depending on the activation pathways induced by different agonists. All espresso, drip and boiled coffee extracts caused dose dependent inhibition of platelet aggregation induced by ADP, collagen, epinephrine, and arachidonic acid (ARA). The most marked inhibition was seen at low doses of collagen or ARA. Espresso and drip extracts inhibited collagen-induced platelet aggregation more than purified caffeine or CGA. Espresso, boiled and drip coffee extracts were also a more potent inhibitors of COX-1 and COX-2 than purified caffeine or CGA. We conclude that inhibition of platelet aggregation and COX-1 and COX-2 may contribute to anti-platelet and anti-inflammatory effects of espresso and drip coffee extracts.

Several studies show that air pollution has become a major problem and a source of great concern. Part of the observed poor air quality can be attributed to the levels of ultrafine particles (UFP), generally defined as the fraction of particles with diameter less than 100 nm which, by their size, are able to enter the blood circulation causing adverse health effects. As the main route of entry into the body is inhalation, several epidemiological studies associate the presence of UFP to total mortality, cardiovascular and respiratory problems. Since there are apparently no worldwide normative references for the control of these particles, this global study aimed to characterise the methods and techniques used worldwide regarding the monitoring and management of UFP. For this purpose, a survey was carried out based on a questionnaire applied at global scale. The questionnaire design was based on a preliminary literature review on the main search engines for scientific publications to establish the state of the art. As a result of the application of the questionnaire, a total of 51 responses were obtained from 20 different countries on five continents, which provided an insight into the global profile of professionals interested in the control/study of UFP, the measurement methodologies they follow and the guideline values they apply, if any. Among them are public health professionals, academics and health engineers from various institutions, such as education, hospitals, research centers and regulators in the health sector. Most responses said are no specific methodologies for the measurement of UFP, nor national standards for it. Through the results obtained in this study, it can be concluded that it is urgent to adopt regulations to standardize the assessments as well as to establish guide values for the protection of the human health.

Asphaltene precipitation and deposition pose significant operational challenges in both reservoirs and surface facilities by inducing formation damage. To understand the kinetics involved in asphaltene particle nucleation, growth, and aggregation, this study employed confocal microscopy and centrifuge-based methods under a unified set of experimental parameters. The acquired time-resolved particle size images were analyzed using MIPAR image processing software, while asphaltene mass yield was quantitatively evaluated through centrifugation. Experimental conditions were varied to study the effects of heptane concentration, asphaltene concentration, and shear rate. Notably, this investigation introduces, for the first time, the parameter of particle count as an additional variable influencing asphaltene mass production. This study aims to discern how particle count correlates with asphaltene mass yield over time. Results indicate that the minimum mean particle diameter was observed to be 2 microns, which progressively grew up to 80 microns. The mean particle diameter exhibited a positive correlation with both asphaltene concentration and shear rate, whereas an inverse correlation was seen with heptane concentration. Furthermore, the asphaltene mass yield was found to increase with greater asphaltene and heptane concentrations, as well as with higher shear rates. The relationship between mean particle diameter and mass yield was found to be nonlinear. In the early stages, a higher prevalence of small particles contributed to a greater total particle count, while at later stages, particle aggregation led to the formation of larger particles that influenced the overall asphaltene mass. The insights gained from understanding the relationship between particle diameter, count, and mass yield are crucial for advancing the fundamental science of asphaltene precipitation and deposition. These findings may also guide future research that relies solely on particle counts for assessing asphaltene deposition.

Some optimal control problems need metaheuristics in searching for the optimal solution, especially when the process has certain characteristics like the Photobioreactor for Algae Growth (distributed parameter, nonlinearities, etc.). Particle Swarm Optimization (PSO) algorithms within control structures are a realistic approach; their task is often to predict the optimal control values working with a process model (PM). Owing to numerous numerical integrations, there is a big computational effort that is reflected in a large controller execution time. The authors propose to replace the PSO predictor with a machine learning model that has “learned” the quasi-optimal behavior of the couple (PSO, PM); the training data is obtained through closed-loop simulations over the control horizon. The new controller should preserve the process’s quasi-optimal control. In identical conditions, the process evolutions must also be quasi-optimal. The multiple Linear Regression and the Regression Neural Networks were considered as predicting models. The paper first proposes algorithms for collecting and aggregating data sets for the learning process. Algorithms for constructing the machine learning models, implementing the controllers, and closed-loop simulations are also proposed. The simulations prove that the two machine learning predictors have learned the PSO predictor’s behavior such that the process evolves almost identically. The resulting controllers’ execution time drastically decreased while keeping their optimality.

Titanium dioxide nanoparticles have risen concerns about their possible toxicity and the European Food Safety Authority recently banned the use of TiO2 nano-additive in food products. Following the intent of relating nanomaterials atomic structure with their toxicity without having to conduct large scale experiments on living organisms, we investigate the aggregation of titanium dioxide nanoparticles using a multi-scale technique: starting from ab initio Density Functional Theory to get an accurate determination of the energetics and electronic structure, we switch to classical Molecular Dynamics simulations to calculate the Potential of Mean Force for the connection of two identical nanoparticles in water; the fitting of the latter by a set of mathematical equations is the key for the upscale. Lastly, we perform Brownian Dynamics simulations where each nanoparticle is a spherical bead. This coarsening strategy allows studying the aggregation of a few thousand nanoparticles. Applying this novel procedure, we find three new molecular descriptors, namely, the aggregation free energy and two numerical parameters used to correct the observed deviation from the aggregation kinetic described by the Smoluchowski theory. Molecular descriptors can be fed into QSAR models to predict the toxicity of a material knowing its physicochemical properties, without having to conduct large scale experiments on living organisms.

Fractal behavior and long-range dependence are widely observed in measurements and characterization of traffic flow in high-speed computer networks of different technologies and coverage levels. This paper presents the results obtained when applying fractal analysis techniques on a time series obtained from traffic captures coming from an application server connected to the Internet through a high-speed link. The results obtained show that traffic flow in the dedicated high-speed network link have fractal behavior when the Hurst exponent is in the range of 0.5, 1, the fractal dimension between 1, 1.5, and the correlation coefficient between –0.5, 0. Based on these results, it is ideal to characterize both the singularities of the traffic and its impulsiveness during a fractal analysis of temporal scales. Finally, based on the results of the time series analyses, the fact that the traffic flows of current computer networks exhibit fractal behavior with a long-range dependency is reaffirmed.

Aggregating data is the main line of any discipline dealing with fusion of information from the knowledge-based systems to the decision-making. The purpose of aggregation methods is to convert a list of objects, all belonging to a given set, into a single representative object of the same set usually by an n-ary function, so-called aggregation operator. Since the useful aggregation functions for modeling real-life problems are limit, the basic problem is to construct a proper aggregation operator for each situation. During the last decades, a number of construction methods for aggregation functions have been developed to build new classes based on the well-known operators. This paper reviews some of these construction methods where they are based on transformation, composition and weighted rule.

We report on the effects of the film morphology on the fluorescence spectra for a thin film including a quinoxaline-based co-polymer (TQ1) and a fullerene derivative (PC₇₀BM). The ratio between the polymer and the fullerene derivative, as well as the processing solvent were varied. Beside the main emission peak at 700 nm in the fluorescence spectra of thin films of this phase-separated blend, a broad emission band is observed with a maximum at 520 - 550 nm. The intensity of this emission band decreases with an increasing degree of mixing in the film and becomes most prominent in thicker films, films with high PC₇₀BM content, and films that were spin-coated from solvents with lower PC₇₀BM solubility. We assign this emission band to aggregated PC₇₀BM.

The concept of neutrosophic number is a significant mathematical tool to deal with real scientific problems because it can tackle indeterminate and incomplete information which exists generally in real problems. In this article, we use neutrosophic numbers (a + bI), where a and bI denote determinate component and indeterminate component respectively. We explore the situations in which the input information is needed to express in terms of neutrosophic numbers. We define score functions and accuracy functions for ranking neutrosophic numbers. We then define a cosine function to determine unknown criteria weights. We define neutrosophic number harmonic mean operators and proved their basic properties. Then, we develop two novel MCGDM strategies using the proposed aggregation operators. We solve a numerical example to demonstrate the feasibility and effectiveness of the proposed two strategies. Sensitivity analysis with variation of “I” on neutrosophic numbers is performed to demonstrate how the preference ranking order of alternatives is sensitive to the change of “I”. The efficiency of the developed strategies is ascertained by comparing the obtained results from the proposed strategies with the existing strategies in the literature.

Identification and segmentation of rock particles is very important in geology, mining, engineering construction, and environmental monitoring. Traditional methods for recognizing the rock particle characteristics are time-consuming, labor-intensive, and limited by the geographical scope of the sampling sites, which makes it more difficult to represent the spatial distribution of the rock particles accurately. Recent advancements in deep learning techniques offer promising solutions to automate this process. This study aims at utilizing state-of-the-art (SOTA) Mask R-CNN deep learning algorithm from the Detectron2 framework, to capture global features of rocks that will enable the recognition of rock particles more efficiently, just from having the rock images. These images are subject to image processing techniques such as a Gaussian filter, to denoise and smoothen the image, and an Illumination Adaptive Transformer (IAT) framework, to adjust the lighting exposure; all of which add to improve the quality of the image dataset. Afterward, the Mask R-CNN and Detectron2 models are utilized in training the images using transfer learning. Experimental results from evaluating the performance of the proposed algorithms showcase the effectiveness of the approach, thereby highlighting its potential to revolutionize rock particle segmentation across various domains.

Amplitudes of quantum transitions containing time zigzags are considered. The discussion is carried out in the framework of the Minkowski metric and the standard quantum mechanics without adding new postulates. We argue that time zigzags are not suppressed at the quantum level, but their contribution to the amplitude is zero. The result is valid for a single particle and a non-interacting scalar field.

In order to improve the stiffness of the flexible robot,this paper proposes a variable-stiffness elastic actuator to improve the rigidity of flexible robots. The actuator integrates the working principles of a pneumatic drive, wedge structure, and particle blockage. the tensile stiffness of the actuator is nonlinearly negatively correlated with the air pressure because of the structural and material properties.The compressive stiffness and lateral stiffness increases nonlinearly as air pressure increases, being 3and 121 times greater at 0.17 MPa compared to 0 MPa, respectively. Beyond 0.17 MPa, the two stiffness of the actuator experiences incremental growth due to wedge impedance forces.

In a previous paper we have shown that superluminal particles are allowed by the general relativistic theory of gravity provided that the metric is locally Euclidean. Here we calculate the probability density function of a canonical ensemble of superluminal particles as function of temperature. Although only the Lorentzian metric is stable for normal matter density, an Euclidian metric can be created under special gravitational circumstances and persist in a limited region of space-time consisting of the very early universe which is characterized by extremely high densities and temperatures. Superluminal particles also allow attaining thermodynamic equilibrium at a shorter duration and also suggest a rapid expansion of the matter density, thus making mechanism such as inflation (which demands invoking and ad-hoc scalar field) redundant. This is in accordance with Occam’s razor.

Particle swarm optimization (PSO) is an effective algorithm to solve the optimization problem in case that derivative of target function is inexistent or difficult to be determined. Because PSO has many parameters and variants, I propose a general framework of PSO called GPSO which aggregates important parameters and generalizes important variants so that researchers can customize PSO easily. Moreover, two main properties of PSO are exploration and exploitation. The exploration property aims to avoid premature converging so as to reach global optimal solution whereas the exploitation property aims to motivate PSO to converge as fast as possible. These two aspects are equally important. Therefore, GPSO also aims to balance the exploration and the exploitation. It is expected that GPSO supports users to tune parameters for not only solving premature problem but also fast convergence.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

This work aims to develop an integrated fault location and restoration approach for microgrids (MGs). This work contains two parts. Part I presents the fault location algorithm, and Part II shows the restoration algorithm. The proposed algorithms are implemented by particle swarm optimization (PSO). The fault location algorithm is based on network connection matrices, which are the modifications of bus-injection to branch-current and branch-current to bus-voltage (BCBV) matrices, to form the new system topology. The backward/forward sweep approach is used for the prefault power flow analysis. After the occurrence of fault, the voltage variation at each bus is calculated by using the Zbus modification algorithm to modify Zbus. Subsequently, the voltage error matrix is computed to search for the fault section by using PSO. After the allocation of the fault section, the multi-objective function is implemented by PSO for optimal restoration with its constraints. Finally, the IEEE 37-bus test system connected to distributed generations is utilized as the sample system for a series simulation and analysis. The outcomes demonstrated that the proposed optimal algorithm can effectively solve the fault location and restoration problem in MGs.

In the past two decades the world experienced an exceptional number of unprecedented extreme weather events, some causing major human suffering and economic damage, such as the March 2012 heat event, which was called “Meteorological March Madness.” From the beginning of space era a correlation of solar flares with pressure changes in atmosphere within 2–3 days or even less was reported. In this study we wanted to test the possible relation of highly warm weather events in North-East America with Solar Energetic Particle (SEP) events. For this reason we compared ground temperatures T_M in Madison, Wisconsin, with energetic particle fluxes P measured by the EPAM instrument onboard the ACE spacecraft. In particular, we elaborated case events and the results of a statistical study of the SEP events related with the largest (Dst ≤ −150nT) Coronal Mass Ejection (CME)-induced geomagnetic storms, between with the years 1997–2015. The most striking result of our statistical analysis is a very significant positive correlation between the highest temperature increase_. ΔT_M and the time duration of the temperature increase ΔT_M (r = 0.8, p <0.001) at “winter times” ( r = 0.5, p , 0.01 for the whole sample of 26 SEP examined events). The time response of T_M to P was found to be in general short (a few days), but in the case of March 2015, during a gradual P8 increase, a cross-correlation test indicated highest c.c. within 1 day (p < 0.05). The March 2012 “meteorological anomaly” was elaborated in the case of South-East Europe, where, beside a period of strong winds and rainfall (6-13.3.2012), intense precipitation in North-East Greece (Alexandroupoli) were found to be correlated with distinct high energy flux enhancements. A rough theoretical interpretation is discussed for the space—atmospheric extreme weather relationship we found. However, much work should be done to achieve early warning of space weather dependent extreme meteorological events. Such future advances in understanding the relationships between space weather and extreme atmospheric events would improve atmospheric models and help people’s safety, health and life.

More than fifty million people over the age of fifty have osteoporosis issues due to low bone mass, disease contribution, and not exercising continuously. Certain most important risk factors and causes of osteoporosis contain age, gender, hormones, visits to inexperienced doctors, and certain medical conditions. In this manuscript, we diagnosed certain frank operational laws under the availability of complex intuitionistic fuzzy (CIF) information. Furthermore, using the evaluated operational laws, we pioneered the theory of CIF frank weighted averaging (CIFFWA), CIF frank ordered weighted averaging (CIFFOWA), CIF frank hybrid averaging (CIFFHA), CIF frank weighted geometric (CIFFWG), CIF frank ordered weighted geometric (CIFFOWG), CIF frank hybrid geometric (CIFFHG) operators, and described their beneficial and valuable results with certain useful properties. Moreover, we aim to evaluate the most dangerous type of osteoporosis based on their symptoms, causes, and risk factors using diagnosed approaches. Finally, to enhance the worth of the evaluated operators, we compare the diagnosed result with certain prevailing results and illustrated their geometrical representation with the help of MATLAB.

regulating translational speed and accuracy. Threonylcarbamoyl adenosine (t6A37) and 5-methoxycarbonylmethyl-thiouridine (mcm5s2U34) are critical ASL modifications that have been linked to several human diseases. The model yeast Saccharomyces cerevisiae is viable despite the absence of both modifications, growth is however greatly impaired. The major observed consequence is a subsequent increase in protein aggregates and aberrant morphology. Proteomic analysis of the t6A-deficient strain revealed a global mistranslation leading to protein aggregation without regard to physicochemical properties or t6A-dependent or biased codon usage in parent genes. However, loss of sua5 led to increased expression of soluble proteins for mitochondrial function, protein quality processing/trafficking, oxidative stress response, and energy homeostasis. These results point to a global function for t6A in protein homeostasis very similar to mcm5/s2U modifications.

Pathogen genomics is a critical tool for public health surveillance, infection control, outbreak investigations, as well as research. In order to make use of pathogen genomics data, it must be interpreted using contextual data (metadata). Contextual data includes sample metadata, laboratory methods, patient demographics, clinical outcomes, and epidemiological information. However, the variability in how contextual information is captured by different authorities and how it is encoded in different databases poses challenges for data interpretation, integration, and its use/re-use. The DataHarmonizer is a template-driven spreadsheet application for harmonizing, validating, and transforming genomics contextual data into submission-ready formats for public or private repositories. The tool’s web browser-based JavaScript environment enables validation and its offline functionality and local installation increases data security. The DataHarmonizer was developed to address the data sharing needs that arose during the COVID-19 pandemic, and was used by members of the Canadian COVID Genomics Network (CanCOGeN) to harmonize SARS-CoV-2 contextual data for national surveillance and for public repository submission.In order to support coordination of international surveillance efforts, we have partnered with the Public Health Alliance for Genomic Epidemiology to also provide a template conforming to its SARS-CoV-2 contextual data specification for use worldwide. Templates are also being developed for One Health and foodborne pathogens. Overall, the DataHarmonizer tool improves the effectiveness and fidelity of contextual data capture as well as its subsequent usability. Harmonization of contextual information across authorities, platforms and systems globally improves interoperability and reusability of data for concerted public health and research initiatives to fight the current pandemic and future public health emergencies. While initially developed for the COVID-19 pandemic, its expansion to other data management applications and pathogens is already underway.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

In this work, a generalized analogue to the Pauli spin matrices is presented and investigated. The proposed Hermitian spin matrices exhibit a general symmetry. The generalized spin projection operators are derived and the electrodynamics for hypothetical fermions are explored using the proposed spin matrices. The fermionic quantum Heisenberg model is constructed using the proposed spin matrices and comparative studies against simulation results using the Pauli spin matrices are conducted. Further analysis on key findings as well as discussions on extending the proposed spin matrix framework to describe hypothetical bosonic systems (spin-1) are provided.

An analysis is presented of the possible existence of a second anomalous dipole moment of Dirac’s particle next to the one associated with the angular momentum. It includes a discussion why, in spite of his own derivation, Dirac has doubted about its relevancy. It is shown why since then it has been overlooked and why it has vanished from leading textbooks. A critical survey is given on the reasons of its reject, including the failure of attempts to measure and the perceived violations of time reversal symmetry and charge-parity symmetry. It is emphasized that the anomalous electric dipole moment of the pointlike electron (AEDM) is fundamentally different from the quantum field type electric dipole moment of an electron (eEDM) as defined in the standard model of particle physics. The analysis has resulted into the identification of a third type Dirac particle, next to the electron type and the Majorana particle. It is shown that, unlike as in the case of the electron type, its second anomalous dipole moment is real valued and is therefore subject to polarization in a vector field. Examples are given that it may have a possible impact in the nuclear domain and in the gravitational domain.

In this paper, we implement a new method binary Particle Swarm Optimization (PSO) for solving the kidney exchange problem, which will improve the future decisions of kidney exchange programs. Because using a kidney exchange, we can help incompatible patient-donor couples to swap donors to receive a compatible kidney. Kidney paired donation programs provide an innovative approach for increasing the number of available kidneys. Further, we implementing binary particle swarm optimization in parallel with MATLAB with one, two, three and four threads and from the computations point of view, the authors compare the performance to reduce the running time for kidney exchange to match patients as fast as possible to help clinicians. Moreover, implementing binary particle swarm optimization in solving the kidney exchange problem is an effective method. The obtained results indicate that binary PSO outperforms other stochastic-based methods such as genetic algorithm, ant lion optimization, and efficient the number of resulting exchanges.

We study the effect of the degeneracy factor in the energy levels of the well-known Landau problem for a magnetic engine. The scheme of the cycle is composed of two adiabatic processes and two isomagnetic processes driven by a quasi-static modulation of external magnetic field intensity. We derive the analytical expression of the relation between the magnetic field and temperature along the adiabatic process and, in particular, reproduce the expression for the efficiency as a function of the compression ratio.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

The surface configurations of the low-index facets of a set of spinel oxides are investigated using DFT+U calculations to derive surface energies and predict equilibrium nanoparticle shapes via the Wulff construction. Two very different conditions are investigated, corresponding to application either in heterogeneous catalysis or in electrocatalysis. First, the bare stoichiometric surfaces of NiFe₂O₄, CoFe₂O₄, NiCo₂O₄, ZnCo₂O₄ spinels are studied to model their use as high-temperature oxidation catalysts. Second, focusing attention on the electrochemical oxygen evolution reaction (OER), and on the CoFe₂O₄ inverse spinel as the most promising OER catalyst, we generate surface configurations by adsorbing OER intermediates, and, in an innovative study, we recalculate surface energies taking into account adsorption and environmental conditions, i.e., applied electrode potential and O₂ pressure. We predict that, under OER operating conditions, (111) facets are dominant in CoFe₂O₄ nanoparticle shapes, in fair agreement with microscopy measurements. Importantly, in the OER case we predict a strong dependence of nanoparticle shape upon O₂ pressure. Increasing O₂ pressure increases the size of the higher-index (111) and (110) facets at the expense of the (001) more catalytically active facet, whereas the opposite occurs at low O₂ pressure. These predictions should be experimentally verifiable and help define the optimal OER operative conditions.

The base excitation of mechanical equipment can result in pipeline system vibration which seriously affects the safe operation of the equipment. Particle damping technology is based on the particle collision dissipation principle to realize the structural vibration energy dissipation. This paper introduces the particle damping method into the vibration control of pipeline system. A particle damper has been designed for the structural characteristics of the pipeline. The influence of the material and structure of the pipeline particle damper, the external excitation and other parameters on the energy dissipation characteristics of particle damping are revealed. The energy dissipation mechanism of the pipeline particle collision damper under various parameter is analyzed. A pipeline vibration reduction test system with particle damping has been established. The effects of different excitation conditions, damper materials and number of unit structures of particle damper on the vibration damping effect of pipeline systems are investigated comparatively. The influence of damper parameters on the vibration suppression of pipeline system is obtained. The research in this paper can provide technical references for vibration suppression of pipeline systems.

Pyrolyzed waste biomass, or biochar, has been suggested as a means to increase plant growth and to mitigate soil salinization, which is a widespread agricultural issue and can reach extreme levels in urban soils impacted by de-icing salts. Soil mixing is enhanced by reduced biochar particle size; however, biochar properties vary with particle size and recent studies suggest that plant growth responses may be maximized at intermediate particle sizes. We examined the responses of two plant species (cowpea (Vigna unguiculata) and velvetleaf (Abutilon theophrasti)) to biochar amendments that spanned a wide range of particle sizes obtained by sieving, with and without de-icing salt additions. The smallest size fractions of biochar reduced plant growth relative to unamended controls. Plant biomass production was generally maximized at intermediate biochar particle size treatments, with particles sizes of 0.5-2.0 mm showing the best response. Mitigation of salt effects was also improved at intermediate biochar particle sizes in this particles size range. Our results emphasize the importance of optimizing biochar particle size to best enhance plant responses to biochar, with particular reference to saline soils.

Detecting rotated objects in remote sensing images poses a substantial challenge. These images usually cover a wide field of view, containing diverse and complex backgrounds with variously sized ground objects densely distributed. Therefore, identifying objects of interest in remote-sensing images is challenging. While integrating Convolutional Neural Networks (CNNs) and Transformer networks has exhibited progress in detecting rotated objects, there is still scope for enhancing feature extraction and fusion. To address this issue, we propose a feature extraction module, a feature context aggregation module, and a multi-scale feature fusion module. Initially, we substitute the Spatial Pyramid Pooling Bottleneck (SPPFBottleneck) with a new module aimed at extracting multi-scale features, thereby enhancing the detection of small objects in complex backgrounds. Next, we develop a novel module for the multi-scale fusion of contextual information within feature maps, extracting valuable information. Finally, we combine the original features with the fused ones to prevent the loss of specific features in the fusion process. We refer to our newly proposed model as the "Multi-scale Feature Context Aggregation Network" (MFCANet). We assess our approach on three challenging remote sensing datasets: MAR20, SRSDD, and HRSC. Comprehensive experimental results show that our method surpasses baseline models by 2.13%, 10.28%, and 1.46% mAP on the MAR20, SRSDD, and HRSC datasets, respectively.

Detecting rotational objects in remote sensing imagery is a significant challenge. These images typically encompass a broad field of view, featuring diverse and intricate backgrounds, with ground objects of various sizes densely scattered. As a result, identifying objects of interest within these images is a daunting task. While the integration of Convolutional Neural Networks (CNN) and Transformer networks leads to some advancements in rotational object detection, there is still room for improvement, particularly in enhancing the extraction and utilization of information related to smaller objects. To address this, our paper presents a multi-scale feature fusion module and a global feature context aggregation module. Initially, we fuse original, shallow, and deep features to reduce the loss of shallow feature information, thereby improving the detection performance of small objects in complex backgrounds. Subsequently, we compute the correlation of contextual information within feature maps to extract valuable insights. We name the newly proposed model the "Multiscale Feature Context Aggregation Module" (MFCA). We evaluate our proposed methodology on three challenging remote sensing datasets: DIOR-R, HRSC, and MAR20. Comprehensive experimental results show that our approach surpasses baseline models by 2.07\% mAP, 1.02\% mAP, and 1.98\% mAP on the DIOR-R, HRSC2016, and MAR20 datasets, respectively.

Amyloids were conventionally referred to as extracellular and intracellular accumulation of Aβ42 peptide which causes the formation of plaques and neurofibrillary tangles inside the brain leading to the pathogenesis in Alzheimer’s disease. Subsequently, amyloid-like deposition was found in the etiology of Prion diseases, Parkinson disease, Type II Diabetes and Cancer which was attributed to the aggregation of Prion protein, α-Synuclein, Islet Amyloid Polypeptide Protein and p53 protein respectively. Hence, traditionally amyloids were considered as aggregates formed by the proteins or peptides exclusively. However, since the last decade it has been discovered that other metabolites like single amino acids, nucleobases, lipids, glucose derivatives etc. have propensity to form amyloid-like toxic assemblies. Several studies suggest direct implications of these metabolite assemblies in the patho-physiology of various Inborn errors of metabolisms like Phenylketonuria, Tyrosinemia, Cystinuria and Gaucher’s disease to name a few. In this review, we present a comprehensive literature overview which suggests amyloid-like structure formation as a common phenomenon for the disease progression and pathogenesis in multiple syndromes. The review on this topic is urgently required to create awareness about the understanding of fundamental molecular mechanism behind the origin of diseases from an amyloid perspective and possibly look for a common therapeutic strategy for the treatment of these maladies by designing generic amyloid inhibitors.

Global models have been developed to tackle the challenge of forecasting sets of series that are related or share similarities, but not for heterogeneous datasets. Various methods of partitioning by relatedness have been introduced to enhance the similarities of the set, resulting in improved forecasting accuracy but often at the cost of a reduced sample size, which could be harmful. To shed light on how the relatedness between series impacts the effectiveness of global models in real-world demand forecasting problems we perform an extensive empirical study using the M5 competition dataset. We examined cross-learning scenarios driven by the product hierarchy commonly employed in retail planning, which allow global models to capture interdependencies across products and regions more effectively. Our findings show that global models outperform state-of-the-art local benchmarks by a considerable margin, indicating that they are not inherently more limited than local models and can handle unrelated time series data effectively. The accuracy of data partitioning approaches increases, as the size of the data pools and the models' complexity decrease. However, there is a trade-off between data availability and data relatedness. Smaller data pools lead to increased similarity among time series, making it easier to capture cross-product and cross-region dependencies, but this comes at the cost of a reduced sample, which may not be beneficial. Finally, it's worth noting that the successful implementation of global models for heterogeneous datasets can significantly impact forecasting practice.

The human androgen receptor (AR) is a ligand inducible transcription factor harboring an amino terminal domain (AR-NTD) hosting the ligand independent activation function. AR-NTD is intrinsically disordered and display aggregation properties conferred by the presence of a poly-glutamine (polyQ) sequence of 22 residues. The length of the polyQ sequence, as well as the presence of adjacent sequence motifs modulate this aggregation property. AR-NTD contains also a conserved sequence motif KELCKAVSVSM that displays an intrinsic property to form amyloid fibrils under mild oxidative conditions of its conserved cysteine residue. As peptide sequences with intrinsic ability to oligomerize are reported to have an impact on the aggregation of polyQ tract, we determined the effect of the KELCKAVSVSM on the polyQ stretch in the context of the AR NTD, using Atomic Force Microscopy (AFM). Here, we present evidence for a crosstalk between the amyloidogenic properties of the KELCKAVSVSM motif and the polyQ stretch at the AR NTD.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

The study of interactions between polyelectrolytes (PE) and surfactants is of great interest for both fundamental and applied research. These mixtures can represent, for example, models of self-assembly and molecular organization in biological systems, but they are also relevant in industrial applications. Amphiphilic block polyelectrolytes represent an interesting class of PE, but their interactions with surfactants have not been extensively explored so far, most studies being restricted to non-associating PE. In this work, interactions between an anionic amphiphilic triblock polyelectrolyte and different types of surfactants bearing respectively negative, positive and no charge, are investigated via surface tension and solution rheology measurements for the first time. It is evidenced that the surfactants have different effects on viscosity and surface tension, depending on their charge type. Micellization of the surfactant is affected by the presence of the polymer in all cases; shear viscosity of polymer solutions decreases in presence of same charge or nonionic surfactants, while the opposite charge surfactant cause precipitation. This study highlights the importance of the charge type, and the role of the associating hydrophobic block in the PE structure, on the solution behavior of the mixtures. Moreover, a possible interaction model is proposed, based on the obtained data.

Optical forces are used to aggregate plasmonic nanoparticles and create SERS-active hot spots in liquid. When biomolecules are added to the nanoparticles, high sensitivity SERS detection is accomplished. Here we tailor this methodology to detect catalase and hemoglobin, two Raman resonant biomolecules, at concentrations down to 10 nM and 1 pM. Subsequently, we study the SERS signal in Bovine Serum Albumin as a function of the concentration, finding a monotonic dependence that suggests the possibility of quantitative detection. Finally, by exploiting nanoparticles functionalized with specific aptamers, we obtain first results on the SERS detection of Ochratoxin A, a fungal toxin found in food commodities and wine. This represents a first step towards the addition of molecular specificity to this novel biosensor strategy.

This study aimed to improve sensitivity of ferrous particle sensors used in various mechanical systems such as wind power gearboxes to detect abnormalities by measuring the amount of ferrous wear particles generated by metal-to-metal contact. Existing sensors collect ferrous particles using a permanent magnet. However, its ability to detect abnormalities is limited because it only measures amounts of ferrous particles collected on the top of the sensor. To overcome this limitation, this study evaluated sensibility of an existing sensor using a multi-physics analysis method and improved it by changing the core shape inside the sensor. The detection ability of the improved sensor was analytically shown to be better than the existing sensor. This study highlights the use of analytical methods and multi-physics analysis for developing a ferrous particle sensor and presents a method to compare sensibility analytically. Results of the improved sensor are expected to enhance the ability to detect abnormalities in the lubrication system where ferrous wear particles are generated. This study will contribute to the development of more effective ferrous particle sensors, which can potentially improve the performance and reliability of mechanical systems.

The fluid flow field at the upper airways is highly complex due to the complex structure of the airway. The inhaled particle flow, the air streamline and the interaction of the continuum and discrete phase could significantly affect the transport behaviour of the inhaled particles. A range of analytical, mathematical and computational fluid dynamics (CFD) models analyzed the airflow and particle transport in different idealized and asymmetric airway models. A precise understanding of the continuum and discrete phase interaction in realistic human airways is missing, and this study aims to develop a CFD-DEM model for particle transport in realistic airways. This study uses the CFD model for the continuum phase and the discrete element method (DEM) for the discrete phase. A soft sphere approach is used for the interaction of the discrete phase. Proper validation is performed for particle transport efficiency. The CFD-DEM model analyzed the particle transport in an idealized and realistic airway model, and different methods are used to analyze the transport behaviour. During the particle-particle interaction, a stagnation point and a high-pressure zone are observed at the airway model's carinal angle. The numerical results report higher deposition efficiency (DE) for particle-particle interaction than without interaction. The flow field becomes highly complex with the spring constant values, and higher DE is found for high spring constant values. The spring dashpot friction-dshf method shows higher deposition at the upper part of the airways than other interaction methods. The findings of this study and more case-specific analysis would improve the knowledge of aerosol transport in airways and the health risk assessment of the patient.

Prior studies have focused on the overall behavior of randomly moving particle swarms. However, the characteristics of ubiquitous special particle swarms that form in these swarms remain unknown. This study demonstrates a generalized diffusion equation for randomly moving particles that considers the velocity and location aggregation effects in a special circumstance (that is, in a moving reference frame R_u relative to a stationary reference frame R₀). This equation can be approximated as the Schrodinger equation in the microcosmic case and describes the kinetics of the total mass distribution in the macrocosmic case. The predicted density distribution of the particle swarm in the stable aggregation state is consistent with the total mass distribution of massive, relaxed galaxy clusters (at least in the range of r < r_s), preventing cuspy problems in the empirical Navarro-Frenk-White (NFW) profile. This article is helpful for inspiring people to think about the essence of universal gravitation.

The wave-particle description of quantum mechanics is briefly reviewed to set an analogy between the quantum mechanics of particles and fields and quantum cosmology. It is shown that quantum cosmology can be seen as a quantum field theory developed in the space of three metrics (the metrics of the spatial sections of the spacetime), where the classical evolution of the universe corresponds to a definite trajectory and the quantum mechanics of matter fields emerges as the first order quantum correction. Like in a quantum field theory developed in an isotropic background, the universes are created in universe-antiuniverse pairs, which might provide us with an explanation for the matter-antimatter asymmetry observed in our universe without going beyond the standard model. Moreover, the states of the matter and the antimatter fields of the pair of universes are entangled and that makes that their initial states are in a non-vacuum state (presumably in a thermal state). That might open the possibility of looking for observable imprints of the creation of universes in pairs is the astronomical data.

Astrophysical accretion processes near the black hole candidates, such as active galactic nuclei (AGN), X-ray binary (XRB), and other astrophysical sources, are associated with high-energetic emission of radiation of relativistic particles and outflows (winds and/or jets). It is widely believed that the magnetic field plays a very important role to explain such high energetic processes in the vicinity of those astrophysical sources. In the present research note, we propose that the black hole is embedded in an asymptotically uniform magnetic field. We investigate the dynamical motion of charged particles in the vicinity of a weakly magnetized black hole. We show that in the presence of the magnetic field, the radius of the innermost stable circular orbits (ISCO) for a charged particle is located close to the black hole’s horizon. The fundamental frequencies, such as Keplerian and epicyclic frequencies of the charged particle are split into two parts due to the magnetic field, as an analog of the Zeeman effect. The orbital velocity of the charged particle measured by a local observer has been computed in the presence of the external magnetic field. We also present an analytical expression for the four-acceleration of the charged particle orbiting around black holes. Finally, we determine the intensity of the radiating charged accelerating relativistic particle orbiting around the magnetized black hole.

Magnetic Particle Imaging (MPI) is a new imaging modality that sensitively and specifically detects superparamagnetic iron oxide nanoparticles (SPIONs). Many labs have been developing cellular magnetic resonance imaging (MRI) tools using both SPIONs and fluorine-19 (19F)-based contrast agents for numerous important applications, including tracking of immune and stem cells used for cellular therapies. SPION-based MRI cell tracking has very high sensitivity, but low specificity. SPIONs produce negative contrast in MRI, or signal voids. SPIO is not directly detected by MRI, but indirectly through its relaxation effects on protons, therefore, it is not possible to reliably quantify the local tissue concentration of SPION particles and cell number cannot be determined. 19F based cell tracking uses perfluorocarbons (PFC) to label cells. The number of 19F atoms can be directly measured from 19F MR images and related to cell number. 19F MRI has high specificity, but low sensitivity. MPI cell tracking displays great potential for overcoming the challenges of MRI-based cell tracking allowing for both high cellular sensitivity and high specificity and quantification of SPIO labeled cell number. In this paper we describe nanoparticle and MPI system factors that influence MPI sensitivity and resolution, quantification methods and give our perspective on testing and applying MPI for cell tracking.

Current numerical methods for simulating biophysical processes in aquatic environments are typically constructed in a grid-based Eulerian framework or as an individual-based model in a particle-based Lagrangian framework. Often, the biogeochemical processes and physical (hydrodynamic) processes occur at different time and space scales, and changes in biological processes do not affect the hydrodynamic conditions. Therefore, it is possible to develop an alternative strategy to grid-based approaches for linking hydrodynamic and biogeochemical models that can significantly improve computational efficiency for this type of linked biophysical model. In this work, we utilize a new technique which links hydrodynamic effects and biological processes through a property-carrying particle model (PCPM) in a Lagrangian/Eulerian framework. The model is tested in idealized cases and its utility is demonstrated in a practical application to Sandusky Bay. Results show the integration of Lagrangian and Eulerian approaches allows for a natural coupling of mass transport (represented by particle movements and random walk) and biological processes in water columns which is described by a nutrient-phytoplankton-zooplankton-detritus (NPZD) biological model. This method is far more efficient than traditional tracer based Eulerian biophysical models for 3-D simulation, particularly for a large domain and/or ensemble simulations.

Water is essential for living organisms. The increase in world population, global climate change and rapid growth in industrialization and urbanization have brought with them water issues around the world in recent years. Not only should existing water resources be used reasonably and efficiently but alternative water resources should also be explored and secured. Rainwater harvesting, which is one of the alternative water resources, can provide economic and environmental solutions. For rainwater harvesting, the size of reservoirs in which rainwater captured from roof catchments is stored should be determined. Determining the optimum tank capacity depending on precipitation and consumption rates allows us to make maximum use of rainwater tanks. The aim of this study is to determine the optimum tank capacity for the storage of rainwater captured from roof catchments in order to meet the water demand for agricultural production. Precipitation data were collected from the city of Isparta and its districts. Rainwater tank capacity was determined using the Rippl, residual mass curve, minimum flow and particle swarm optimization methods. Storage capacities varying according to roof areas and consumption rates are shown in a graph. Results show that particle swarm optimization is the best method.

We present a tutorial to realize a multidimensional fitting procedure capable of extracting all the relevant information contained in a sequence of charged particle images acquired as a function of time in femtosecond pump-probe experiments. The images are reproduced using a 3D fitting method, which provides the velocity (or center-of-mass kinetic energy) and angular distributions contained in the images and their time evolution. A detailed example of the method is shown through the analysis of the time-resolved predissociation dynamics of CH₃I on the B-band origin [Gitzinger et al., J. Chem. Phys. 133, 234313 (2010)]. We show that the multidimensional approach is essential for the analysis of complex images that contain several overlapping contributions where reduced dimensionality analyses cannot provide a reliable description of the features present in the image sequence. This methodology can be generalized to many types of multidimensional data analysis.

Physics of high-Tc superconducting cuprates is obscured by the effect of strong electronic correlations. One way to overcome the problem is to seek for an exact solution at least within the small cluster and expand it to the whole crystal. Such an approach is in the heart of the cluster perturbation theory (CPT). Here we develop CPT for the dynamic charge and spin susceptibilities (spin-CPT), within which the correlation effects are explicitly taken into account by the exact diagonalization. We apply spin-CPT to the effective two-band Hubbard model for the cuprates obtained from the three-band Emery model and calculate one- and two-particle correlation functions, namely, spectral function and spin and charge susceptibilities. Doping dependence of the spin susceptibility was studied within spin-CPT and CPT-RPA that is the CPT generalization of the random phase approximation (RPA). Both methods produce the low energy response at four incommensurate wave vectors in qualitative agreement to the results of the inelastic neutron scattering on overdoped cuprates.

In this paper, a relativistic scalar particle under Lorentz symmetry breaking effects in the presence of a scalar potential is investigated. We introduce the scalar potential by modifying the mass via transformation M → M+S(r) in the wave equation and analyze the behaviour of a scalar particle. We see that the analytical solution to the KleinGordon equation can be achieved, and the energy eigenvalues and the wave function depends on the Lorentz symmetry breaking parameters as well as potential

Multi-wire saw machining (MWSM) used for slicing hard-brittle materials in semiconductor, is an important material removal process that uses free abrasives. Cutting model of single-wire saw machining (SWSM) is the basis of MWSM, and the material removal mechanism of SWSM can better understand than MWSM. Mathematical model (includes brittle fracture and plastic deformation) is presented in this paper for SWSM ceramic with abrasives. This paper determines the effect of various machining parameters on the removal of hard-brittle materials. For brittle fracture of SWSM ceramics, the minimum of the strain energy density is used as a fracture criterion. The material removed of SWSM ceramics due to plastic deformation is calculated using the equations of motion. Actual wire-sawing experiments are conducted to verify the results from the developed mathematical model. Theoretical results agree with experimental data and practical experience. The developed mathematical model shows that brittle fracture plays a major concern role in material removed of SWSM ceramics. Wire speed and working load have positively correlated with material removed of SWSM ceramics. The coefficient of friction is low, a lateral crack, which propagates almost parallel to the working surface, leads to more brittle fracture and material removed is increased on SWSM ceramics.

Particle Swarm Optimization (PSO) is a metaheuristic global optimization paradigm that has gained prominence in the last two decades due to its ease of application in unsupervised, complex multidimensional problems which cannot be solved using traditional deterministic algorithms. The canonical particle swarm optimizer is based on the flocking behavior and social co-operation of birds and fish schools and draws heavily from the evolutionary behavior of these organisms. This paper serves to provide a thorough survey of the PSO algorithm with special emphasis on the development, deployment and improvements of its most basic as well as some of the very recent state–of-the-art implementations. Concepts and directions on choosing the inertia weight, constriction factor, cognition and social weights and perspectives on convergence, parallelization, elitism, niching and discrete optimization as well as neighborhood topologies are outlined. Hybridization attempts with other evolutionary and swarm paradigms in selected applications are covered and an up-to-date review is put forward for the interested reader.

The increasing micro and nanoplastic pollution is of immense concern. Recent studies show that biofilm substances in contact with nanoplastics play an important role in aggregation and sedimentation of nanoplastics. Consequences of these processes are changes in biofilm formation and stability and changes in transport and fate of pollutants in the environment. Having a deeper understanding of the nanoplastics-biofilm interaction would help to evaluate the risks posed by uncontrolled nanoplastic pollution. These interactions are impacted by environmental changes due to climate change, such as e.g. acidification of surface waters. We apply fluorescence correlation spectroscopy (FCS) to investigate the pH-dependent aggregation tendency of non-functionalized polystyrene (PS) nanoparticles (NPs) due to intermolecular forces with model extracellular biofilm substances. Our biofilm model consists of bovine serum albumin (BSA), which serves as a representative for globular proteins, and the polysaccharide alginate, which is a main component in many biofilms, in solutions containing Na+ with ionic strength being realistic for fresh water conditions. Biomolecule concentrations ranging from 0.5 g/l up to at maximum 21 g/l are considered. We use non-functionalized polystyrene NPs as representative for mostly negatively charged nanoplastics. BSA promotes NP aggregation through adsorption onto the NPs and BSA mediated bridging. In BSA-alginate mixtures the alginate hampers this interaction, most likely due to alginate-BSA complex formation. Thus, the NP are more stable in the BSA-alginate mixtures compared to solutions containing solely BSA. In most BSA-alginate mixtures and alginate alone, other weaker attractive forces, mainly depletion forces, seem to cause NP aggregation. These forces are not electrostatic in nature and thus are less influenced by the pH-value. At high BSA contents the electrostatic BSA-BSA attraction is not sufficiently screened leading to a destabilization of the NP. This study clearly shows that it is crucial to consider correlative effects between multiple biofilm components to better understand the NP aggregation in the presence of complex biofilm substances. Single component biofilm model systems based on comparing the total organic carbon content of the extracellular biofilm substances, as usually considered, would have led to an misjudgment of the stability towards aggregation. Nevertheless, if the protein content is not too high, a simple model that only depends on polysaccharide concentration could be feasible to predict aggregation under environmental relevant conditions.

RNA, as an important substance for regulating biological growth and development, has significant implications for visualization research. However, many spontaneously fluorescent substances in plants greatly interfere with the effectiveness of plant bioimaging. Aggregetion- induced emission luminogens (AIEgens), due to their luminescent properties, tunable molecular size, high fluorescence intensity, good photostability, and low cell toxicity, have been widely applied in the animal and medical fields. We have found that AIEgens have great potential as RNA fluorescent probes for efficient imaging in plants. In this review, we first introduce several common RNA labeling forms and point out their pros and cons. We briefly describe the development of AIEgens and the AIE mechanism, and then present various practical applications of AIEgens, including detailed examples of their use as biological markers. To further promote the application of AIE in the field of RNA, we suggest the use of AIEgens to modify target RNA via techniques such as click chemistry or CRISPR/Cas, to achieve RNA visualization in plants. highly possible to modify target RNA with AIEgens in vivo for RNA visualization.

Underwater robotics equipped with visual detection systems have the function of detecting un-derwater artifacts, which is of great significance to deep-sea archaeology. Underwater artifacts are located in complex environments with poor imaging conditions, and the targets have chal-lenging problems such as breakage, stacking, and sediment burial, which causes the marine cul-tural target detection failures. To solve these problems, this paper proposes an underwater cul-tural target detection algorithm based on the deformable deep aggregation network model for underwater robotics exploration. To fully extract the target feature information of underwater targets in complex environments, this paper designs a multi-scale deep aggregation network with deformable convolutional layers. Besides, the BAM attention module is designed for fea-ture optimization, which enhances the potential feature information of the target while weak-ening the background interference information. Finally, the target prediction is achieved through feature fusion at different scales. The proposed algorithm has been extensively validat-ed and analyzed on the collected underwater artifact datasets, and the precision, recall, and mAP of the algorithm have reached 93.1%, 91.4%, and 92.8%, respectively. In addition, the present al-gorithm has been practically deployed on the underwater robotics. In the deep-sea tests, the ar-tifact detection frame rate reaches up to 19 fps, which satisfies the real-time target detection。