The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

In Yaoundé, Cameroon, excessive and inappropriate speeding remains a major public health concern. Part of the problem are the unsafe speed limits, lack of evidence, and effective evaluation of speeding safety performance indicators (SSPIs), and the absence of speed management, hindering the city's ability to mitigate the risks associated with speeding. This study aimed to address this knowledge gap by assessing SSPIs using a well-defined methodology and suggesting speed management strategies. Data on speed, traffic volumes and road attributes were collected from a random selection of 16 representative road sections in Yaoundé. Seven SSPIs were calculated, and weights were assigned to evaluate city-level SSPIs. The findings showed that 66.8% of drivers drive within the speed limit, generally operating at speeds of 54 km/h with a speed variation of 26 km/h. Based on the speed analysis, evidence-based strategies are proposed, and implementing these strategies could potentially reduce fatalities and serious injuries by 16% to 84% across study locations, as indicated by Elvik's model. These findings have significant policy implications for reducing speeding in Yaoundé, and the methodological approach can be replicated in other urban settings. Future research should extend SSPI evaluation to the national level and test the effectiveness of the recommended strategies.

The effectiveness of combining strength-specific training with endurance training to enhance the performance of endurance runners remains uncertain. This study aimed to analyze effect of practising maximum-strength (MAX), explosive strength (EXP) or both combined (COMB) on seven runners’ performance-indicators: vertical jump (VJ), one-repetition-maximum-squat (1RM), peak-velocity/peak-running-speed (PV), lactate-threshold (over incremental-test-protocols, LT), middle-distance-time-trial (TT), maximum-oxygen-consumption (VO2max), running-economy (RE). Systematic-review (Scopus, Wed of Science, Sports Discuss, PubMed) with meta-analysis was conducted following PRISMA standards. Inclusion-criteria (PICOS) were: recreational or well-trained athletes aged 18-45 performing concurrent-training ≥five-week. Used search-terms were related to different types of strength/endurance, participants’ age, sport-modality. 20 manuscripts were selected, quality-assessed with PEDro. MAX training is more effective than EXP, COMB in improving VJ, 1RM, PV, while COMB is more effective than MAX, EXP to enhance TT. MAX is more effective than EXP in improving LT. Concurrent-workouts do not provide additional benefits to VO2max. It is unknown which strength-modality (MAX, EXP or COMB) is more effective in improving RE. Concurrent-training is more effective than single-mode-endurance-training for enhancing specific performance-variables in adult-endurance-runners. Middle-, long-distance-runners may consider incorporating MAX-training to target specific goals, e.g., improving VJ, 1RM, LT, PV while utilizing COMB-training to enhance TT. Certain variables may benefit from EXP. New randomized-controlled-trials are required to confirm these findings.

This article conceptualises the link between firms’ value chains and distribution networks and the requirements for double materiality assessments in contemporary reporting regulations worldwide. The new European Sustainability Reporting Standards (ESRS) and the standards for sustainability reporting issued by the International Sustainability Standards Board (ISSB), called IFRS S1 and IFRS S2, require companies to report their own direct (scope 1) and indirect (scope 2) greenhouse gas (GHG) emissions as well as GHG emissions in their value chains and distribution networks (both scope 3). However, GHG emissions comprise just one dimension of information that is relevant to understand when assessing, managing and reporting the footprints and impacts of a firm and are, therefore, only a fraction of the key performance indicators (KPIs) related to ESG that should be disclosed. Through a case study, this article demonstrates the connection between the due diligence analysis of firms’ value chains and distribution networks, the analysis of the competitive parameters of the business model, the identified impacts, risks and opportunities, and the double materiality perspective. The double materiality perspective prioritises actions based on probability and significance, creating a natural space to identify KPIs. The article concludes by applying the REGS model and illustrating how it can assist firms in identifying relevant KPIs based on double-materiality assessments.

The vast array of interconnected microbes across earth’s ecosystems and within holobionts has been called the “Internet of Microbes.” Research into the fundamental microbial properties has demonstrated that bacteria and archaea are masters of energy and information collection, storage, transformation, and dissemination using both “wired” and wireless (at a distance) capacities. These features suggest that microbes are quantum entangled within and between earth’s holobionts, and that specific tools affecting energy and information functions could provide an effective strategy for managing microbial populations. Microbes use four critically important microbial networking functions (sound, light, electricity, and magnetism). This narrative review focuses on microbial management based on two of the four: sound and light (as well as related vibrations). These are examined as: 1) tools for managing microbial populations, 2) tools to support new technologies, and 3) tools for healing humans and other holobionts. Given microbial sensitivity to sound, light, and vibrations, it is critical that microbial populations and microbe-laden holobionts are protected from potentially damaging exposures. We conclude that sound, light, and vibrations are useful therapeutic tools that can help support useful microbial populations and help to address ongoing challenges of holobiont disease.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.

The purpose of this paper is to explore which financial performance indicators (FPIs) evaluate the level of supply chain capability (SCC) that explicitly touches all of the business functions and processes within and beyond the company. The authors investigated nine FPIs that were selected from the financial statements of 155 companies within nine industries. The authors find that suitable FPIs to measure SCC for shareholders’ value are return-on-assets (ROA), days-sales-outstanding (DSO), and current ratio (CR). This means that higher ROA, shortened DSO, and an appropriate level of CR could reach a sustainable supply chain. These results will help the industry to avert a major disruption in supply chain processes and activities using suitable financial performance indicators.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

Taekwondo masters and coaches believe that they have a kind of “eagle eye” and that is why they feel comfortable to analyze athletes’ skills without using essential tools. The aim of this study was to analyze the athletes’ technical indicators during performance of the Miluh-chagi kick. To analyze the reliability and precision of the cycle of ten kicks (n = 120), performed by 5 women and 7 men senior athletes, we used an expert panel and a previously published observational tool. The coefficient of variation was calculated to verify precision. The intraclass correlation coefficient was calculated to confirm the reliability among the evaluators. Student’s t-test was used for group-to-group analysis. Correlation analyses were accessed using Spearman’s rho. The data quality sample reliability results, for group, intra- and inter-rater were excellent and good re-spectively. Statistically significant differences, with a large effect size, were found in the foot take-off, knee up and start leg flexion observational moments. The values showed a small and negative to moderate correlation between the conducts and aggregates criteria. Perfect correlation values were found between support leg foot and contact leg position. These findings meet the measurement requirements of athletes’ technical indicators to analyze motor behavior, develop-ment and performance of this technique.

The performance of OpenFOAM in strong scaling tests on HPC systems with AMD EPYC processors exhibits a pronounced superlinear speedup. Simple test cases show superlinear speedups of over 300%, which significantly impacts the efficient use of computing resources. With the last generation of HPC architectures, a superlinear speedup of about 10% to 20% was well expected and accepted by CFD users. The measured superlinear speedup is much more pronounced and withstands the communication overhead to even larger scales. A detailed performance analysis of OpenFOAM follows, employing various High-Performance Computing (HPC) architectures, including AMD, ARM and Intel systems. The performance metric FVOPS (Finite VOlumes solved Per Second) is introduced to compare the performance of Computational Fluid Dynamics (CFD) applications when varying the grid size, as occurs in a strong scaling test. The achievable FVOPS depends on various factors, including the simulation type, boundary conditions, and especially the grid size of a use case. Analysing FVOPS on a single node level with varying grid size shows a significant difference in performance and cache utilization, which explains the large superlinear speedups seen in the strong scaling tests. Furthermore, FVOPS can be used as a simple benchmark to determine the optimal number of grid elements per rank to simulate a given use case at peak efficiency on a given platform, resulting in time, energy, and cost savings. The FVOPS metric also facilitates the direct comparison between different HPC architectures. The tests using AMD, ARM, and Intel processors show a peak in performance when employing around 10,000 grid elements per core. The presence of a large L3 cache on AMD processors is particularly advantageous, as indicated by L3 cache miss rates observed on AMD EPYC processors. Our results suggest that future HPC architectures with larger caches and higher memory bandwidth would benefit the CFD community.

As a representative of Exponential Organizations, MI went from obscurity to the Fortune 500 in just ten years. Mi's success is inextricably linked to its outstanding business model. This paper summarizes the elements of MI's business model from four perspectives: value proposition, value creation, value delivery, and value capture, as well as its measures for developing into an exponential organization. Expecting to provide theoretical references for the transformation and upgrading of manufacturing organizations.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

(1) Background: The aim of the research was to present and emphasize the importance of magnetic resonance imaging (MRI) in diagnosing Achilles tendon (AT) ruptures by presenting case reports. (2) Materials and Methods: The sample of respondents included 7 patients (4 males and 3 females, 2 athletes and 5 non-athletes), aged 25 to 58 years, with AT injuries, who were examined and treated at the Institute for Treatment and Rehabilitation "Niška Banja", Niš, Serbia. Ankle examinations with MRI were conducted using the Esaote O-scan 0.3 T machine. The examinations were performed without the application of a paramagnetic contrast agent and without the use of anesthesia. Results: The MRI method's sensitivity and overall diagnostic accuracy were excellent, with 100% true positives. In our study, the method accurately detected the presence, location, and severity of AT injuries in all cases. MRI is an important and reliable method for detecting AT injuries, classifying them, monitoring the course of recovery, and assessing the effects of therapy. Conclusions: An unrecognized or delayed diagnosis of an AT injury can lead to chronic changes. Timely diagnosis (clinical examination, ultrasonography, magnetic resonance imaging) and appropriate treatment (conservative or operative) enable patients to return to normal activities, including sports. Unfortunately, the use of MRI is limited by restricted access and the cost of the examination.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

Distracted driving is a major cause of road traffic crashes in Yaoundé. Partly due to scarcity of enforcement, lack of evidence and investigation of distraction safety performance indicator (SPI), hindering evidence-based intervention. This study aimed to address this evidence gap by evaluating the distraction SPI using proven methodology. Data on distracted driving (handheld mobile device; interaction; eating/smoking/drinking) were collected from roadside observation on 36 randomly selected road sections carefully spread to cover the city. SPI were computed and weighted with traffic volume to ensure representativeness of values. A total of 41,004 drivers were observed (38,248 in car; 1,116 in van; 977 in truck; 663 in bus). The prevalence of distracted driving in Yaoundé is 13.69% for the three distractions type combined. The prevalence is 7.84% for interaction, 4.89% for handled mobile device usage and 0.96% for eating/smoking/drinking. Leveraging these insights, a seven year (2024 - 2030) fighting strategy aiming at halving the prevalence was developed. The strategy contains intervention including on legislation/enforcement, which have been proven effective. This study, pioneer in Yaoundé, provide stakeholders with evidence of the issue and measures to implement and can also serve when developing road safety strategy.Future research should consider investigation at national level.

The missing link between cross-sectoral resource utilisation and management, and full-scale adoption of the water-energy-food (WEF) nexus has been lack of analytical tools to support policy and decision-making. This paper defined WEF nexus sustainability indicators and developed a methodology to calculate composite indices to facilitate WEF nexus performance, monitoring and evaluation. WEF nexus indicators were integrated through the Analytic Hierarchy Process (AHP) in a multi-criteria decision-making (MCDM). Data were normalised to determine composite indices. The method established quantitative relationships among WEF nexus sectors to indicate resource utilisation and performance over time, using South Africa as a case study. A spider graph of normalised indices was used to illustrate WEF nexus indicator performance and inter-relationships, providing a synopsis of the level of interactions and inter-connectedness of WEF nexus sectors. The shape of the spider graph is determined by the level of the interdependencies and interactions among the WEF nexus sectors, whose management is viewed either as sustainable or unsustainable depending on the classification of the developed integrated index. The spider graph produced for South Africa shows an over emphasis on food self-sufficiency and water productivity at the expense of other sectors, which results from the sectoral approach in resource management. Although the calculated integrated index of 0.203 for South Africa is classified as lowly sustainable, the emphasis is on the quantitative relationships among the indicators and on how to improve them to achieve sustainability. The developed method provides evidence to decision makers, indicating priority areas for intervention. The analytical model is another niche area for the WEF nexus, as it is now capable to evaluate synergies and trade-offs in a holistic way to improve efficiency and productivity in resource use and management for sustainable development.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

The purpose of this study is to examine the match-related performance (scores and penalties) of the athletes in the Junior EJC (European Judo Championship) and U23 EJC categories before and immediately after the Covid-19 quarantine, according to gender and weight category groups. Our sample was based on the junior and U23, male and females, 2019-2020 Junior European Judo Championships and 2019-2020 U23 European Judo Championships. A total of 1431 matches in these tournaments were analyzed: male (n=812) and female (n=619). The main findings of this study showed that most matches in both the male and female categories resulted in ippon (2019-2020 average: 64,35% for Junior male, 70,55% for U23 male and 69,3% for Junior female, 64,4% for U23 female). No significant differences (p > 0.05) were observed between gender and age groups concerning the match scores. In the formation phase of the technique, considerations of high- and low-intensity actions, and analysis of the speed of athletes during matches in official competitions can help to better understand the dynamics of the variability of movements in judo matches. In addition, suggestions are presented to be applied to athletes in different age categories who are on the way to become Olympic athletes.

Quality of life (QoL) assessments are integral to cancer care, yet their effectiveness in providing essential information for supporting survivors varies. This study aimed to elucidate key indicators of QoL among colorectal cancer survivors from the perspective of healthcare professionals, and to evaluate existing QoL questionnaires in relation to these indicators. Two studies were conducted: a Delphi study to identify key QoL indicators and a scoping review of questionnaires suitable for colorectal cancer survivors. Fifty-four healthcare professionals participated in the Delphi study's first round, with 25 in the second. The study identified two primary QoL domains (Physical and Psychological) and 17 subdomains deemed most critical. Additionally, a review of 12 questionnaires revealed two instruments assessing the most important general domains. Findings underscored a misalignment between existing assessment tools and healthcare professionals' clinical priorities in working with colorectal cancer survivors. To enhance support for survivors' QoL, efforts are needed to develop instruments that better align with the demands of routine QoL assessment in clinical practice.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

A lead zirconate titanate [PZT;Pb(Zr_0.52Ti_0.48)O₃] layer embedded infrared (IR) detector decorated with wavelength-selective plasmonic crystals has been investigated for high-performance non-dispersive infrared (NDIR) spectroscopy. A plasmonic IR detector with an enhanced IR absorption band has been designed based on numerical simulations, fabricated by conventional microfabrication techniques, and characterized with a broadly tunable quantum cascade laser. The enhanced responsivity of the plasmonic IR detector at specific wavelength band has improved the performance of NDIR spectroscopy and pushed the limit of detection (LOD) by an order of magnitude. In this paper, a 13 fold enhancement in the LOD of a methane gas sensing using NDIR spectroscopy is demonstrated with the plasmonic IR detector.

With the rise of Blockchain technology, the cryptocurrency market has been gaining significant interest. In particular, the number of cryptocurrency traders and the market capitalization have grown tremendously. However, predicting cryptocurrency price is very challenging and difficult due to the high price volatility. In this paper, we propose a classification machine learning approach in order to predict the direction of the market (i.e., if the market is going up or down). We identify key features such as Relative Strength Index (RSI) and Moving Average Convergence Divergence (MACD) to feed the machine learning model. We illustrate our approach through the analysis of Bitcoin close price. We evaluate the proposed approach via different simulations. Particularly, we provide a backtesting strategy. The evaluation results show that the proposed machine learning approach provides buy and sell signals with more than 86% accuracy.

Meteorological drought indicators are commonly used for agricultural drought contingency planning in Ethiopia. Agricultural droughts arise due to soil moisture deficits. While these deficits may be caused by meteorological droughts, the timing and duration of agricultural droughts need not coincide with the onset of meteorological droughts due to soil moisture buffering. Similarly, agricultural droughts can persist even after the cessation of meteorological droughts due to delayed hydrologic processes. Understanding the relationship between meteorological and agricultural droughts is therefore crucial. An evaluation framework was developed to compare meteorological and agricultural droughts using a suite of exploratory and confirmatory tools. Receiver operator characteristics (ROC) was used to understand the covariation of meteorological and agricultural droughts. Comparisons were carried out between SPI-2, SPEI-2 and Palmer Z-index to assess intra-seasonal droughts and between SPI-6, SPEI-6 and PDSI for full-season evaluations. SPI was seen to correlate well with selected agricultural drought indicators but did not explain all the variability noted in agricultural droughts. The relationships between meteorological and agricultural droughts exhibited spatial variability which varied across indicators. SPI is better suited to predict non-agricultural drought states more so than agricultural drought states. Differences between agricultural and meteorological droughts must be accounted for better drought-preparedness planning.

Recovery of forest after logging can be tested in many ways: the presence of particular species of fauna or flora, the similarity of the biodiversity of the recovering forest to that on neighbouring areas of undisturbed forest; or the characteristics of soils and streams whose conditions may have drastically changed during logging. Three cases of rainforest recovery after logging and clearance from Australia and Borneo exhibit different starting and different goals for recovery. Faunal indicators of recovery vary with size and with species dependence of the rainforest. Endemic forest species may have difficulty in recovering. Tree species richness and abundance may recover in two decades, but canopy closure takes longer. Compacted soils may retain low infiltration capacities for many decades. This diversity in recovery rates is confirmed when compared with those used elsewhere. Because the starting points for recovery vary, from damage by tropical cyclones and landslides, to clearance for shifting cultivation, pasture or agriculture, to post-logging conditions, universal indicators may be inappropriate. The desired endpoints of recovery also range from a “wilderness” state to a National Park for human enjoyment, biodiversity preservation, safeguarding rights of traditional forest-dwelling peoples, or a second round of selective logging.

Building Country Resilience is a long-term process particularly in the hyper connected world we are living today; and depends on good governance and appropriate equilibrium of respect for people, planet and profits as well as avoiding depleting natural resources that end up affecting the biosphere. Hence represent a most needed Learning ability that may be seeing to be related to the process of Sustainable Development. So, this paper seeks to find best practices and a Ranking of Countries that may help as guides to foster Country Resilience. For this purpose, it was developed a World Resilience Index - WRI based on a Statistical Analysis with updated data from 108 Countries divided into 3 Groups: American Countries – AMER (20 Countries), Advanced Economies - AVECO (22 Countries) mostly from Europe and OTHER (66 Countries); and using a set of Synthetic Variables like the Social Progress Index – SPI, the Environmental Performance Index – EPI, and the Sustainable Development Goals Index – SDGI, besides some related to Governance and the World Risk Index – WRI.

Precise individual tree or sample-based inventories derived from 3D point cloud data of mobile laser scanning can improve our comprehensive understanding of the structure, function, resilience, biodiversity, and ecosystem services of urban forests. This study assessed the performance of a hand-held laser scanning system for the extraction of tree position, diameter at breast height (DBH) and tree height (H) in an urban area. A total of 2083 trees of 13 species from 34 plots were analyzed. The results showed that the registration of tree positions using ground control points (GCPs) demonstrated high accuracy, with errors consistently below 0.4 m, except for a few instances. The extraction accuracy of DBH for all trees and individual species remained consistently high, with a total root mean square error (RMSE) of 2.06 cm (6.89%) and a bias of 0.62 cm (2.07%). Notably, broad-leaved trees outperformed coniferous trees, with RMSE and bias values of 1.86 cm (6%) and 0.76 cm (2.46%) compared to 2.54 cm (9.46%) and 0.23 cm (0.84%). Tree height extraction accuracy varied significantly among different species, with R2 values ranging from 0.65 to 0.92. Generally, both DBH and height were underestimated. Linear mixed effects models (LME) were applied to evaluate factors affecting the performance of HLS with the plot as a random factor. LME analysis revealed that plant type and terrain significantly influenced the accuracy of DBH and H derived from HLS data. Other fixed factors of plot area, tree density and trajectory length didn’t have significance. With a large sample size, we concluded that the HLS demonstrated sufficient accuracy in extracting individual tree parameters in urban forests.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Understanding the dynamics of teamwork and communication among healthcare professionals is crucial in the face of evolving healthcare challenges. This study assessed relational coordination among healthcare professionals in the South Tyrolean healthcare system in Italy, focusing on communication and teamwork dynamics in a cross-sectional survey. Using the validated Relational Coordination Survey (RCS) instrument and 525 completed online responses, the questionnaire aimed to understand the implications of different levels of relational coordination ratings by general practitioners, hospital physicians, nurses, and administrative personnel (response rate 26%). The demographics of the participants revealed a predominance of female professionals (64%), with an average age of 50 and 18 years of service. The resulting RCS scores varied significantly across professional groups, with nurses reporting the highest within-group scores, indicating moderate coordination, and administrators reporting the lowest scores, reflecting areas of weak coordination. Between-group relational coordination was generally perceived as weak across professional groups, with the least weakness observed between general practitioners and nurses. German or Italian language and health district affiliation emerged as significant factors influencing relational coordination ratings, highlighting the need for differentiated understanding and strategies in multilingual and diverse regional settings. Assessments of interdisciplinary feedback and referral practices highlight the variation in teamwork and communication weaknesses and underscore the need for targeted interventions to improve relational coordination. This study provides insights into the complexity of relational dynamics in health care settings. It suggests that improving relational coordination through tailored strategies could significantly improve team effectiveness, quality of patient care, and overall system efficiency.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

The aim of the present trial was to evaluate the growth performance of buffalo calves fed diets characterized by different forage/concentrate ratio with or without the Saccharomyces Cerevisiae supplementation (CBS 493.94, Yea-Sacc®). Twenty-four male buffalo calves (mean age 145.1 ± 16.1 days; mean weight 108.0 ± 18.7) were assigned randomly to 4 groups, homogeneous for age, fed four different diets: diet 1 F:C ratio 50:50; diet 2 F:C ratio 30:70; diet 3 F:C ratio 50:50 + Yea-Sacc® and diet 4 F:C ratio 30:70 + Yea-Sacc®. Buffalo calves were individually weighted before the start of the experiment and the data were used as a covariate, monthly until the end of the trial. Dry matter intake (DMI), daily weight gain (DWG) and feed conversion ratio (FCR) were calculated. The differences in diets’ composition significantly (p

The article deals with human resource management and selected personnel indicators in 10 sustainable development. The main goal of this paper is to analyse and describe human resource 11 management focused on audit of workload, motivation of employees, the competence of staff, their 12 knowledge and experience. The article shows how the selected personnel indicators are examined 13 in selected establishments of multinational company in Slovakia, as an attractive employer inter-14 ested in growth of its employees, thus employer branding. For research methods, a case study meth-15 odology is used. Data collection was carried out through a questionnaire survey with employees in 16 the company as well as an interview with sale advisors and managers. The research aimed to point 17 out a case study of the investigation of selected personnel indicators in human resources manage-18 ment in a selected company and to examine the perception of the performance of employees in 19 connection with their financial evaluation and their satisfaction in the selected company with an 20 impact on employees´ performance. Furthermore, the research aimed to determine whether there 21 was a dependence between the subjectively perceived performance of the employees and selected 22 aspects. Further indicators were calculated, such as employment rate, proportion of wasted time 23 and labour productivity.

The article deals with human resource management and selected personnel indicators in sus-tainable development. The main goal of this paper is to analyse and describe human resource management focused on audit of workload, motivation of employees, the competence of staff, their knowledge and experience. The article shows how the selected personnel indicators are examined in selected establishments of multinational company in Slovakia, as an attractive em-ployer interested in growth of its employees, thus employer branding. For research methods, a case study methodology is used. Data collection was carried out through a questionnaire survey with employees in the company as well as an interview with sale advisors and managers. The research aimed to point out a case study of the investigation of selected personnel indicators in human resources management in a selected company and to examine the perception of the per-formance of employees in connection with their financial evaluation and their satisfaction in the selected company with an impact on employees´ performance. Furthermore, the research aimed to determine whether there was a dependence between the subjectively perceived performance of the employees and selected aspects. Further indicators were calculated, such as employment rate, proportion of wasted time and labour productivity.

The performance of the presurgical test (preSurg) for temporal lobe epilepsy (TLE) was evaluated via video-electroencephalography (VEEG), electroencephalography (EEG), 99mTc-HmPAO single-photon emission tomography (SPECT) and 1.5 T magnetic resonance imaging (MRI) in a group of 112 men (37.0 ± 1.1 years) and 106 women (39.7 ± 1.1 years) operated on for TLE. The epileptic zone (EZ) was adequately identified to determine whether the patient reached an Engel I grade (EI) at least one year postop. Accuracy was evaluated by the coefficient α, ranging from 3 (when result = EZ) to 2 (result in the same hemisphere as the EZ), 1 (noninformative result) or 0 (EZ in the contralateral hemisphere). The simplicity of diagnosis was defined as the number of preSurg surgeries needed to identify the EZ. EI was obtained in 85.8% of patients even though 42.2% of patients had noninformative MRI results. For preSurg α was (mean ± SEM) = VEEG (2.83 ± 0.04) > MRI (2.14 ± 0.08) > EEG (1.87 ± 0.09) > SPECT (1.71 ± 0.09). The accuracy (combination of sensitivity and specificity) was calculated as follows: VEEG (0.797) > MRI (0.518) > EEG (0.446) > SPECT (0.360). The likelihood positive ratio was greater, and the likelihood negative ratio was lower for VEEG. The most relevant factor for the regression model was VEEG (3.106) > MRI (2.558) > EEG (1.905), and the factors were not significantly related to SPECT. EZs in EI patients with low simplicity were identified mainly by VEEG. A very good postoperative outcome can be obtained even in TLE patients with no lesions on MRI. The VEEG is the most reliable preSurg test and may be the only reliable test for patients with very low simplicity (i.e., difficult).single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Diaminomaleonitrile (DAMN) is an electron-rich ligand which is commonly used in the synthesis of purines, amides and Schiff base ligands. In the last case lies the interest in this molecule, given its symmetry and apparent facility to form various ligands and complexes of interest in fields such as organic solar cells and catalysis among others. Nevertheless, its bisubstitution with aldehydes displays certain difficulty due to the double conjugated presence of the nitrile group (C≡N) in its structure, which significantly affect its coordination behavior by modulating the chemical reactivity of its amines. In addition to presenting a practical resume of guidelines for the preparation of different bisubstituted compounds from DAMN, this paper reviews the possibility of attaining a precise characterization by simple spectroscopic techniques. We provide an additional discussion for one of these techniques (commonly reported but often overlooked), given its potential to provide both the symmetry and E/Z configuration of the product. We hope the comprehensive evidence discussed and shown in this review will be helpful to further develop and understand the products derived of this interesting molecule in their broad applications.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

The main purpose of the study was to study the effects of a specific rowing ergometer training program on the athletic performance of young adolescents (n=56; 11.73 ± 1.4 years old) com-pared to a workout based on general strength training. Eight-week training program was im-plemented, with four sessions per week and two-hours per session. Sample was divided in two groups: a control group (CG) that performed circuit training with exercises aimed at building general strength and an experimental group (EG) who focused on specifically training on a rowing ergometer (rowing machine). The data obtained in a rowing meter test over the compe-tition distance were analyzed to obtain the average power attained (W) at the beginning of the training, at the middle (4 weeks), at the end of the training (8 weeks) and one year after the ex-perimentation. The results show that, although both forms of training improve the average W obtained in both categories, the EG subjects (+29.94W) obtained better averages in all phases of the study compared to the CG (+5.88W). Furthermore, this increase was greater in male rowers (+ 34.06W) than in female rowers (+24.54W). These results reveal that a specific rower rowing ergometer training program has a significant effect than a general strength program and these effects can even be observed a year after the intervention.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

This paper investigates the feasibility of a backend design for real-time, multiple-channel processing digital phased array system, particularly for high-performance embedded computing platforms constructed of using general purpose digital signal processors. Frist, we obtained the lab-scale backend performance benchmark from simulating beamforming, pulse compression, and Doppler filtering based on MicroTCA chassis using Serial RapidIO protocol in backplane communication. Next, a field-scale demonstrator of a multifunctional phased array radar is emulated by using the similar configuration. Interestingly, the performance of a barebone design is compared to that of emerging tools that systematically take advantage of parallelism and multicore capabilities, including Open Computing Language.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

The notion of potential-growth indicator came to being in the field of matrix population models long ago, almost simultaneously with the pioneering Leslie model for age-structured population dynamics, albeit the term has been given and the theory developed only recent years. The indicator represents an explicit function, R(L), of matrix L elements and indicates the position of the spectral radius of L relative to 1 on the real axis, thus signifying the population growth, or decline, or stabilization. Some indicators turned out useful in theoretical layouts and practical applications prior to calculating the spectral radius itself. The most senior (1994) and popular indicator, R0(L), is known as the net reproductive rate, and we consider two more ones, R1(L) and RRT(A), developed later on. All the three are different in what concerns their simplicity and the level of generality, and we illustrate them with a case study of Calamagrostis epigeios, a long-rhizome perennial weed actively colonizing open spaces in the temperate zone. While the R0(L) and R1(L) fail respectively because of complexity and insufficient generality, the RRT(L) does succeed, justifying the merit of indication.

Recently, more and more countries are entering the global race for university competitiveness. On the one hand, global rankings are a convenient tool for quantitative analysis. On the other hand, their indicators are often difficult to quickly calculate, they often contradict each other. We thought about using widely available indicators for a quick analysis of the University's publication strategy. We opted for the normalized citation indicators available in SciVal analytical tool, i.e. Source Normalized Impact per Paper (SNIP) and Field-Weighted Citation Impact (FWCI). We have demonstrated the possibility of applying the correlation analysis to the impact indicators of a document and a journal on the sample of the social and humanitarian fields at Peoples' Friendship University of Russia. Particular attention was paid to the application of the results in practice.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Capital structure decision plays an imperative role in firm’s performance. Recognizing the importance, there has been many studies inspected the rapport of capital structure with performance of firms and findings of those studies are inconclusive. In addition, there is relative deficiency of empirical studies examining the link of capital structure with performance of banks in Bangladesh. This paper attempted to fill this gap. Using panel data of 22 banks for the period of 2005-2014, this study empirically examined the impacts of capital structure on the performance of Bangladeshi banks assessed by return on equity, return on assets and earnings per share. Results from pooled ordinary least square analysis show that there are inverse impacts of capital structure on bank’s performance. Empirical findings of this study is of greater significance for the developing countries like Bangladesh because it will call upon concentration of the bank management and policy makers to pursue such policies to reduce reliance on debt and to accomplish optimal level capital structure. This research also contributes to empirical literatures by reconfirming (or otherwise) findings of previous studies.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

Despite the recognized influence of maximum or acceleration strength on combat techniques and countermovement jump (CMJ) performance, the relationship between body segment weights and combat techniques remains unexplored. This study aimed to examine the impact of body segment weights, including striking arm weight (SAW), kicking leg weight (KLW), and trunk weight (TW), on the dynamics of direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and CMJ performance. Sixteen male military cadets (22.3±1.8 years, 181.4±7.0 cm, 83.0±8.1 kg) performed combat techniques, with performance measured by using a force plate and body segment weights assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis was applied. Results indicated a strong correlation between KLW and FK impulse (r = 0.64, p ≤ 0.01) and CMJ impact force (r = 0.80, p ≤ 0.01). SAW showed moderate correlations with DP impulse (r = 0.53, p ≤ 0.05) and ES impulse (r = 0.54, p ≤ 0.05). Additionally, FK peak and impact forces were strongly correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01), and FK peak force moderately correlated with CMJ peak velocity (r = 0.63, p ≤ 0.05). These findings suggest targeted arm strength training could enhance striking abilities, while improvements in leg acceleration strength may directly boost kicking performance and vertical jump capabilities, which are crucial in combat scenarios.

ADHD, one of the most prevalent diseases during childhood, we still do not know its precisely origin, although oxidative/nitrosative stress and the hypothalamic-pituitary-adrenal axis are suggested contributors. Methylphenidate, among others, is the main drug used in these patients, but its effects on relevant markers and structures remain unclear. This study, involving 59 patients diagnosed with ADHD according to DSM-5 criteria, aimed to assess changes in cortisol levels (using cortisol awakening response, CAR) and oxidative/nitrosative status with the treatment. Blood samples before and 3 months after treatment with methylphenidate were used to measure oxidative and inflammatory markers, and the endogenous antioxidant activity, while saliva samples tracked cortisol awakening response (CAR). The results show a treatment-related improvement in the redox profile, with the reduction of advanced oxidation protein products (AOPP), lipid peroxidation (LPO), and nitrite plus nitrate (NOx) levels, and the increase of the enzymatic activities of glutathione reductase (GRd) and catalase (CAT). Moreover, the area under the curve (AUC) of CAR increased significantly, indicating increased reactivity of the HPA axis. These result support by the first time the involvement of the endogenous antioxidant system in the pathophysiology of ADHD.

Correlations between the air permeability coefficient and various pore structure indicators in cementitious materials were examined to determine the pore structure indicator that best evaluated air permeability using data from previous studies of air permeabilities and pore structures. The determination coefficients of air permeability with total pore volume, critical pore diameter, and ordinary threshold pore diameter were low, although these have often been used as indicators. The median and threshold pore diameters obtained by percolation theory showed high determination coefficients. The equation using the threshold pore diameter better estimated the air permeability coefficient than the Katz–Thompson equation.

To understand the relationship between water permeability and the pore structure of cementitious materials, literature that studied both water permeability and the pore structure are reviewed, and their correlation is studied. Although the majority of this data is for cement paste, mortar, concrete, and cemented soil are also included. Based on this study, it is established the determination coefficient between water permeability and the total pore volume is very low; however, those between water permeability and the critical, threshold, and median pore diameters, respectively, are moderate. On the other hand, the threshold pore diameter, derived based on the percolation theory, exhibits a very high determination coefficient. The calculated water permeability, using the Katz and Thompson equation, agrees with the reported water permeability quantitatively to a certain level, but is overestimated.

Emerging autologous cellular therapies that utilize platelet-rich plasma (PRP) applications have the potential to play adjunctive roles in a variety of regenerative medicine treatment plans. There is a global unmet need for tissue repair strategies to treat musculoskeletal (MSK) and spinal disorders, osteoarthritis (OA), and patients with chronic complex and recalcitrant wounds. PRP therapy is based on the fact that platelet growth factors (PGFs) support the three phases of wound healing and repair cascade (inflammation, proliferation, remodeling). Many different PRP formulations have been evaluated, originating from human, in vitro, and animal studies. However, recommendations from in vitro and animal research often lead to different clinical outcomes because it is difficult to translate non-clinical study outcomes and methodology recommendations to human clinical treatment protocols. In recent years, progress has been made in understanding PRP technology and the concepts for bioformulation, and new research directives and new indications have been suggested. In this review, we will discuss recent developments regarding PRP preparation and composition regarding platelet dosing, leukocyte activities concerning innate and adaptive immunomodulation, serotonin (5-HT) effects and pain killing. Furthermore, we discuss PRP mechanisms related to inflammation and angiogenesis in tissue repair and regenerative processes. Lastly, we will review the effect of certain drugs on PRP activity, and the combination of PRP and rehabilitation protocols.

Classical Arabic poetry is a form of Arabic literature, and almost every piece of Arabic poetry follows one of the 16 meters. The rhythmic framework of the poems or the verses is called meters. The deep learning (DL) model was implemented using TensorFlow in this work using a large dataset of Arabic poetry. The character level encoding was used to convert text to integers for classifying the full-verse and half-verse data. The study evaluates the data without removing diacritics from the text. The train-test-split method with a 70-15-15 split was employed for classification. 15% of the total data was considered unseen test data for all models. The work was conducted with multiple deep learning models, including the Long Short-Term Memory (LSTM), Gated Recurrent Units (GRU), and Bidirectional LSTM (Bi-LSTM). The Bi-LSTM model shows the best accuracy of all the models specified, with 97.53% for full-verse and 95.23% for half-verse without removing diacritic data.

The oil and gas industry in Nigeria, a vital contributor to the nation's economy, has long been associated with significant environmental challenges. Pollution, habitat destruction, and greenhouse gas emissions have raised global concerns about sustainability and corporate responsibility. This empirical study explores the relationship between environmental accounting practices and the financial performance of listed oil and gas companies in Nigeria. We investigated eight oil and gas companies that are publicly traded on the Nigerian Stock Exchange Market (NGX) as of January 17, 2022, from 2011 to 2022. The study employs Driscoll-Kraay standard errors and reveals that environmental accounting had significant effects on returns on assets, earnings per share, and liquidity ratio. The study revealed that the implementation of environmental accounting practices had diverse effects on the performance of oil and gas companies in Nigeria. The findings encourage policymakers and stakeholders in the sector to utilise the insights and design more effective regulations and incentives that promote environmental corporate responsibility. Also, valuable insights into the potential benefits and challenges associated with adopting environmental accounting practices, and influencing the decision-making processes of corporate stakeholders were provided to ensure sustainability in terms of improved financial performance of the oil and gas sector in Nigeria.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

The paper proposes a human explainable artificial intelligence approach for mapping the status of environmental phenomena from multisource geo data. It is both knowledge and data driven: it exploits remote sensing expert’s knowledge to define the contributing factors from which partial evidence of the environmental status can be computed. Furthermore, it aggregates the partial evidences to compute a map of the environmental status by adapting to a region of interest through a learning mechanism exploiting Volunteered Geographic Information (VGI), both from in situ observations and photointerpretation. The approach is capable to capture the specificities of local context as well as to cope with the subjectivity and incompleteness of expert’s knowledge. The proposal is exemplified to map the status of standing water areas (i.e. water bodies and river, human driven or natural hazard flooding) by considering satellite data and geotagged observations. Results of the validation experiments were performed in three areas of Northern Italy, characterized by distinct ecosystems. Results of the proposed methodological framework showed better performances than traditional approaches based on single spectral indexes thresholding. The use of expert’s knowledge, possibly imprecise/uncertain and incomplete, the need of few ground truth data for learning, and finally the explainability of learned rules are the distinguishing characteristics of the proposal with respect to traditional machine learning methods.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

Oral health surveys are essential to assess the dental caries experience and to influence national policies. This retrospective cross-sectional study aims to analysis dental caries experience who sought dental treatment in a reference university dental hospital at the Lisbon Metropolitan Area between January 2016 and March 2020. Full-mouth examination, sociodemographic, behaviors and medical information were included. Descriptive analyses and logistic regression analysis were applied to ascertain risk indicators associated with dental caries experience. A final sample of 9,349 participants (5,592 females/3,757 males) were included, aged 18 to 99 years old. In this population, caries experience was 91.1%, higher in female participants. Age (OR= 1.01, 95% CI [1.00-1.02], occupation (OR= 2.94, 95% CI [2.37-3.65], OR= 3.35, 95% CI [2.40-4.67], OR= 2.55, 95% CI [1.66-3.91], for employed, unemployed and retired, respectively), overweight (OR= 1.52, 95% CI [1.18-1.96]), reporting to never visited a dentist (OR= 0.38, 95% CI [0.23-0.64] and self-reported week teeth status (OR= 2.14, 95% CI [1.40-3.28]) were identified as risk indicators for the presence of dental caries, according to adjusted multivariable logistic analyses. These results highlight a substantial rate of dental experience in a Portuguese cohort and will pave the way for future tailored oral public health programs in Portugal.

An increasingly frail population in nursing homes accentuates the need for high quality care at the end of life and better access to palliative care in this context. Implementation of palliative care and its outcomes can be monitored by using quality indicators. Therefore, we developed a quality indicator set for palliative care in nursing homes and a tailored measurement procedure using a mixed-methods design. We developed the instrument in three phases: 1) literature search, 2) interviews with experts and 3) indicator and measurement selection by expert consensus (RAND/UCLA). Second, we pilot tested and evaluated the instrument in nine nursing homes in Flanders, Belgium. After identifying 26 indicators in the literature and expert interviews, 19 of them were selected through expert consensus. Setting-specific themes were advance care planning, autonomy and communication with family. The quantitative and qualitative analyses showed the indicators were measurable, had good preliminary face validity and discriminative power and were considered useful in terms of quality monitoring according to the caregivers. The quality indicators can be used in a large implementation study and process evaluation in order to achieve continuous monitoring of the access to palliative care for all residents in nursing homes.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Serum biochemical indicators serve as vital proxies that reflect the physiological state and functions of different organs. The genetic parameters and molecular mechanisms underlying serum biochemical indicators of sheep (Ovis aries) have not been well understood. Therefore, the aim of the present study was to identify genetic architecture and genomic loci underlying ten serum biochemical indicators in sheep, including alanine transaminase, aspartate transferase, lactate dehydrogenase, cholesterol, glucose, phosphorus, calcium, creatinine, urea concentrations and total protein levels. We implemented genetic parameter estimations and GWAS for each trait in 422 Akkaraman lambs. Overall, low to moderate heritability estimates were found, in the range 0.14–0.55. Additionally, low to high genetic correlations were observed among traits. In total, 23 SNP loci were associated with serum biochemical indicators leading to 19 genes . These are SPTA1, MGST2, CACUL1, IGFBP7, PARD3, PHB1, SLC15A5, TRIM35, RGS6, NUP93, CNTNAP2, SLC7A11, B3GALT5, DPP10, HST2ST1, NRP1, LRP1B, MAP3K9, ENSOARG00020040484.1 as well as LOC101103187, LOC101117162, LOC105611309 and LOC101118029. To our knowledge, these data provide the first association between SPTA1 and serum cholesterol and between ENSOARG00020040484.1 and serum glucose. The current findings provide a comprehensive inventory of the relationships between serum biochemical parameters, genetic variants, and disease-relevant characteristics. This information may facilitate the identification of therapeutic targets and fluid biomarkers and establish a strong framework for comprehending the pathobiology of complex diseases as well as providing targets for sheep genetic improvement programmes.

Key performance indicators are essential for any company to enhance its competitiveness. How-ever, a common issue is the manual collection of production data using record sheets, which are later digitized on desktop computers and processed in Excel sheets. Shockingly, 41% of companies in Mexico have no plans for digitalization. This work aims to develop a Real-time Productivity Indicator Monitoring System using Industry 4.0 technologies for a medium-sized manufacturing firm specializing in die-cutting automotive parts. The Advanced Quality Planning methodology was applied to develop the Conceptual, Product, and Process Engineering and its validation. The experimental tests demonstrated a reliability level of 99.98%, which exceeded initial expectations. The primary contributions presented in this work are related to the development of algorithms, communication protocols, data analysis, and general optimization of the calculation process. The study's only limitation was the short experimentation time.

Loess provides a valuable terrestrial record of past environmental conditions, including the dynamics of air mass circulation responsible for dust transport. Here we explore variations in the luminescence characteristics of sedimentary quartz and feldspar – dominant minerals in loess-palaeosol sequences (LPS) - as possible tools for identifying changes in source. We investigate luminescence sensitivity, a rapidly measurable index which is the product of interplay between source lithology and the history of the mineral in question. Variations in sensitivity down profile may therefore reflect, among other factors such as pedogenesis and reworking, changes in sediment provenance. We undertake an empirical investigation of the luminescence sensitivity of quartz and feldspar from different grain-size fractions from the climatically sensitive Schwalbenberg LPS in the German Rhine valley, comparing samples from a 30 m core spanning the last full glacial cycle with samples of oxygen isotope stage (OIS) 3-2 age exposed within a c. 6 m profile downslope. The temporal overlap enables comparison of luminescence characteristics with respect to possible provenance change during that timeframe. We find an overall inverse relationship between quartz and feldspar sensitivity, as well as variability in sensitivity between different quartz grain sizes. There is some indication that feldspar sensitivity increases during periods of soil formation down the core. In particular, measurements of IR50 sensitivity on unprocessed sediments show correlation with down-profile trends in more established indicators of provenance. This suggests it may be used to provide a reliable, rapid scan of sensitivity changes, and may suggest source variability over millennial timescales.

A study analyzed financial statements in the beer sectors of Italy and Spain during 2019-2021 using compositional data analysis (CoDa) to gauge pre- and post-pandemic financial health and aid sector-level decision-making. Geometric averages were employed to mitigate statistical issues, offering more accurate insights than arithmetic averages. The exploratory, quantitative methodology calculated key financial ratios and profitability metrics. Results indicated satisfactory short-term solvency. Returns and margins remained subpar despite pandemic policies. Geometric averages proved essential in portraying sector health accurately, underscoring the need for their use in classic brewing sector ratios. The study also showcased CoDa's efficacy in diagnosing sectoral financial health for informed decision-making. Furthermore, a web analysis revealed varying transparency levels in communicating non-financial indicators, with Spain excelling in waste, water, and energy disclosures, while Italy prioritized energy and waste with less transparency.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

Prolonged ethanol (EtOH) consumption is associated with male infertility with a decreased spermatogenesis rate as one cause. Defective maturation and development of sperm during their storage in the cauda epididymis and transit in the seminal vesicle can be another cause, possibly occurring before the drastic spermatogenesis disruption. Herein, we demonstrated that the cauda epididymis and seminal vesicle of rats, orally fed with EtOH under a regimen that spermatogenesis was still ongoing, showed histological damage, including lesion and decreased height of the epithelial cells, and increased collagen fibers in the muscle layer, which implicated fibrosis. Lipid peroxidation (shown by malondialdehyde (MDA) levels) was observed, indicating that reactive oxygen species (ROS) was produced along with acetaldehyde during EtOH metabolism by CYP2E1. MDA, acetaldehyde and other lipid peroxidation products could further damage cellular components of the cauda epididymis and seminal vesicle and this was supported by increased apoptosis (shown by TUNEL assay and caspase 9/caspase 3 expression) in these two tissues of EtOH-treated rats. Consequently, functionality of the cauda epididymis and seminal vesicle in EtOH-treated rats was impaired, as demonstrated by decreases in 1H NMR-analyzed metabolites (e.g., carnitine, fructose), which were important for sperm development, metabolism and survival in their lumen.

Angola is vulnerable to climate change, as most of its agriculture is rain-fed and repre-sents the backbone of the people of the southern region of the country, and many peo-ple’s livelihoods depend on it. All crops can suffer from the impacts of climate change, which can lead to challenges in agricultural production and food security in different regions of the world. The work consisted of a systematic review of the impacts of climate change on agriculture in Angola, particularly in the southern region. To achieve this objective the PRISMA2020 methodology was used, using the flowcharts for the selection of studies evaluated from the databases that are: Scopus and Web Sci-ence, resulting in 431 documents published between 1996 and 2023, and of these only 63 were included in the systematic review, with inclusion and exclusion criteria. Research on the short and long-term effects of climate change impacts in agriculture in Angola and in particular the southern region is scarce and insufficient. Temperatures are pre-dicted to rise and precipitation generally decreases over time (approximately -2% by 2100), with the southern region experiencing a stronger drop in precipitation. Agri-culture in Angola will be hit hard and some models show that agricultural productiv-ity will be up to 7% lower by 2050 owing to climate change.

Current pharmacological treatments of Fibromyalgia (FM) are merely symptom palliative, as clinical trials have so far failed to provide overall benefits without associated harms. Polypharmacy often leads to patient´s health deterioration and chronic drug use to an eventual lack of patient´s response. Emerging evidence support that physiotherapy treatments based on mechanical triggers improve FM symptoms and therefore could be used for therapeutic purposes by themselves, or in combination with current pharmacological treatments, as part of integrative medicine programs. However, a paucity of studies rigorously and systematically evaluating this possibility exists. This study uses scores from validated standardized questionnaires, algometer pressure point threshold (PPT) readings and responses from a custom self-developed questionnaire to determine the impact of a pressure-controlled manual protocol on FM hyperalgesia/allodynia, fatigue and patient´s quality of life. The results show that patient´s baseline sensitivity to pain inversely correlates with treatment response in FM. Moreover, patients presenting comorbid ME/CFS do not seem to respond to the applied therapy as those presenting FM only. Thus, pre-treatment PPTs and ME/CFS comorbidity may serve as indicators to predict patient´s response to physiotherapy programs based on mechanical triggers, as the one evaluated here. These unexpected findings grant further explorations including the study of gene expression profiles associating to patient´s treatment response in the blood collection of samples generated by this study.

The Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost deviations using proprietary T/S and T/C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

The present study aims at investigating the relationship between Initial Public Offerings (IPOs) variables mainly underpricing on one hand, and the brand value measures on the other. Our final data set is 104 international brand companies. We implement empirical approach using hierarchical OLS regression and descriptive statistics. We show that underpricing is positively related to brand value which emphasizes the marketing role of going public and underpricing in enhancing brand equity through the product market, which additionally confirms some information asymmetry models. We also find that on average brand companies had not been recognized as brands at the IPO time. Moreover, we show the positive role of private equity in enhancing brand value, additionally, the non-linear association between underpricing and brand value is not evident. Finally, we draw some policy implication and suggestions for future research.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

For this research we are selected three indicators of wheat: yield (t/ha), producer price (USD/t) and share of the harvested area under wheat in relation to the total land area of country (%). The mentioned indicators were analyzed for the period 2006-2021 in thirty-two European countries. The purpose of the research is to determine which of the mentioned indicators achieve average annual growth/decrease rates, what is the correlation between them, how European countries are grouped with their similarities and differences. The research examines the impact of the COVID-19 pandemic on the mentioned indicators in a two time phases: Phase I, before the pandemic (2006-2019); Phase II, during the pandemic (2020-2021). The methodological approach to the research topic involved the application of descriptive statistics, as the method of principal components analysis (abbr. PCA) with graphics. A positive correlation exists only between the yield of wheat and the share of the harvested area under wheat in the total area of the land (0.291). PCA method showed that countries are grouped differently depending on the observed indicator and the analyzed time phase.

The review aims to examine how well numerical indicators of business bankruptcy can predict outcomes. The paper examines ten critical studies that concentrate on statistical models for bankruptcy predictions utilizing PRISMA criteria. The findings highlight the usefulness of numerical indicators in indicating financial hardship, particularly cash flow ratios. In order to connect theoretical knowledge with real-world corporate strategy applications, the study ends by reaffirming the importance of these indicators in strategic decision-making.

Background: Autoimmune inner ear disease (AIED) is a rare autoimmune condition characterized by progressive sensorineural hearing loss with hearing fluctuations over weeks to months, presenting significant challenges in both diagnosis and treatment. Due to its rarity, treatment responses and prognosis in AIED remain poorly understood. Methods: This study reviewed medical records from Taipei Medical University Hospital documented between August 2016 and August 2021. Among 67 patients experiencing fluctuating hearing loss, 11 met the diagnostic criteria for AIED and underwent regular follow-up assessments within a 5-year timeframe. ROC curve was used to discriminate the power of these prognostic parameters. Results: In this study, several factors including younger age, milder initial hearing loss, meeting criteria for bilateral Meniere's disease (MD), having an ascending audiogram pattern, longer time interval between hearing impairment attacks in contralateral ears and responding well to steroids were associated with better prognosis. ROC curve demonstrated the diagnostic value of specific parameters such as the presence of bilateral MD (AUC 0.825, 95% CI 0.640–1.000), pretreatment HI ≤ 45 dB HL (AUC 0.808, 95% CI 0.610–1.000), response to steroids (AUC 0.800, 95% CI 0.595–1.000), and ascending audiogram (AUC 0.858, 95% CI 0.683–0.858). Conclusions: This study identified key prognostic factors for AIED, providing valuable insights for predicting AIED prognosis and facilitating personalized patient management.

Effective prediction of wastewater treatment is beneficial for precise control of wastewater treatment processes. The nonlinearity of pollutant indicators such as COD and TP makes the model difficult to fit and has low prediction accuracy. The classical deep learning methods have been shown to perform nonlinear modeling. However, there are enormous numerical differences between multi-dimensional data in the prediction problem of wastewater treatment, such as COD above 3000 mg/L and TP around 30 mg/L. It will make current normalization methods challenging to handle effectively, leading to the training failing to converge and the gradient disappears or exploding. This paper proposes a multi-factor prediction model based on deep learning. The model consists of a combined normalization layer and a codec. The combined normalization layer combines the advantages of three normalization calculation methods: z-score, Interval, and Max, which can realize the adaptive processing of multi-factor data, fully retain the characteristics of the data, and finally cooperate with the codec to learn the data characteristics and output the prediction results. Experiments show that the proposed model can overcome data differences and complex nonlinearity in predicting industrial wastewater pollutant indicators and achieve better prediction accuracy than classical models.

Spatial planning processes generally consider three levels of planning, which are applied to three types of territory: state, county and city. As the coastal areas are of a significant natural, cultural, economic and social value, as well as are characterized by a diverse range of involved society with specific interests and needs, there is a necessity for an innovative and new approach to sustainable development planning in accordance with the modern age of growth, as well as to work with local communities in specific areas. Planning of a small populated area like village territory is more diverse and subject to the wishes and needs of the population. Small territory planning involves a very narrow circle of individuals or communities that identify spatial development needs for the future, including socio-economic, cultural, and environmental and climate change scenarios. In order to assess the development opportunities and needs of the area, it is necessary to monitor the area by regularly updating data. As it is well known, methodically derived data (facts) provide objectivity and transparency. Nowadays, when information about the present and the past is circulating very fast, it is possible to analyze the current situation, to forecast the future using databases, and to show several constructed realities (scenarios) using the geographic information system (GIS). Therefore, it is crucial to explore and find out the local needs-based planning approach to the development of village in coastal areas.

Studies on the structure of economic systems are, most frequently, carried out by the methods of informational statistics. These methods, often accompanied by a wide range of indicators (Shannon entropy, Balassa coefficient, Herfindahl specialty index, Gini coefficient, Theil index etc.) around which a wide literature has been created over time, have a major disadvantage. Such weakness is related to the imposition of the system condition, therefore the need to know all the components of the system (as absolute values or as weights). This restriction is difficult to accomplish in some situations, and in others, this knowledge may be irrelevant, especially when there is an interest in structural changes only in some of the components of the economic system (either we refer to the typology of economic activities - NACE or of territorial units – NUTS). This article presents a procedure for characterizing the structure of a system and for comparing its evolution over time, in the case of incomplete information, thus eliminating the restriction existent in the classical methods. The proposed methodological alternative uses a parametric distribution, with subunit values for the variable. The application refers to Gross Domestic Product values for five of the 28 European Union countries, with annual values of over 1,000 billion Euros (Germany, Spain, France, Italy and United Kingdom) for the years 2003 and 2015. A form of the Wald sequential test is applied to measure changes in the structure of this group of countries, between the years compared. The results of this application validate the proposed method.

Conventional monitoring relies on "in vivo" (non-destructive) measurements of aboveground organ traits (such as stems, branches, and leaves) to analyze plantation growth trends and assess the effectiveness of management practices like watering and fertilization. This study reveals the necessity of “ex vivo” (destructive) approaches, post-excavation, to ensure fully reliable monitoring of plantation performance, including belowground organ growth and development trends. We showcase the effectiveness of dendrometric analysis, which measures the annual ring width in the secondary xylem (wood) of the taproot and stem. Monitoring above- and belowground organ growth trends allow for the exploration of similarities and differences in how different tree organs respond to internal and external factors. Such monitoring is especially crucial for assessing plantation performance in challenging climates, such as those found in arid and semi-arid lands.

Proteins play a pivotal role in supporting athletes by promoting muscle hypertrophy and minimizing protein catabolism during exercise. They stimulate muscle protein synthesis, aiding in the repair of exercise-induced muscle damage and serving as an energy source, particularly for post-exercise glycogen replenishment. In individuals with phenylketonuria (PKU), for whom protein intake is limited to essential phenylalanine (Phe), supplementation with Phe-free amino acids or glycomacropeptides is necessary. Tailored for macronutrient and micronutrient content, these protein substitutes fulfill most protein requirements, but lack Phe, unlike dietary sources of protein. Protein requirements for athletes with PKU exceed general recommendations due to limited availability in supplements and potential catabolism mitigation. Various factors influence tolerated dietary Phe in PKU, including protein substitute quantity, distribution, pharmacological treatment, age, growth rate, pregnancy, catabolic states, and physical activity. While general protein requirements for PKU surpass those of the general population, adherence to supplement regimens is crucial for athletes and patients with PKU. Strategically timed protein substitutes enhance muscle protein synthesis, body composition, and sports performance within safety limits. Individualized intake is essential for optimal outcomes, as proteins have a multifaceted role in optimizing athletic performance and addressing challenges in PKU.

Melioidosis is an endemic infectious disease caused by Burkholderia pseudomallei bacteria, which contaminates soil and water. To better understand the environmental changes that have contributed to melioidosis outbreaks, this study used spatiotemporal analyses to clarify the distribution pattern of melioidosis and the relationship between melioidosis morbidity rate and local environmental indicators (land surface temperature, normalised difference vegetation index, normalised difference water index) and rainfall. A retrospective study was conducted from January 2013 to December 2022, covering data from 219 sub-districts, with each exhibiting varying morbidity rate of melioidosis on a monthly basis. Spatial autocorrelation was determined using local Moran’s I, and the relationship between melioidosis morbidity rate and the environmental indicators was evaluated using geographically weighted Poisson regression. The results revealed clustered spatiotemporal patterns of melioidosis morbidity rate across sub-districts, with hotspots predominantly observed in the northern region. Furthermore, we observed a range of coefficients for the environmental indicators, varying from negative to positive, which provided insights into their relative contributions to melioidosis in each local area and month. These findings highlight the presence of spatial heterogeneity driven by environmental indicators and underscore the importance of public health offices implementing targeted monitoring and surveillance strategies for melioidosis in different locations.

To accurately and non-destructively monitor the growth of spring wheat in the Hetao Irrigation Area, UAV remote sensing was employed during various fertility stages. Digital image indices from diverse fertilization treatments were calculated and compared with physiological indices to identify the most sensitive digital image indices corresponding to these indices. The study underscored the critical importance of the flowering stage in the growth of spring wheat, thus highlighting the necessity of focusing on this stage. This finding reiterated that the flowering stage was pivotal for spring wheat development in the Hetao Irrigation Area. Several digital image indices, such as GLA, R, G, INT, g, GRVI, MGRVI, RGBVI, EXG, and GRRI, exhibited a high frequency of significant correlations with physiological indices during the four primary reproductive stages of wheat. Consequently, these sensitive digital image indices during the flowering stage can more effectively characterize the physiological indices of spring wheat.

This study aimed to identify sociodemographic and health indicators of diet quality in pre-frail community-dwelling older adults. Pre-frail older adults are those at risk of progression to clinical manifestations of frailty and are targets for preventative intervention. We previously reported that pre-frail older adults have reasonably good overall diet quality. However, further analyses found low intake of energy, protein and several micronutrients. Methods: We collected detailed dietary intake from pre-frail (FRAIL scale 1-2) older adults using NZ Intake24, an online version of 24-hour multiple pass dietary recall. Diet quality was ascertained with the Diet Quality Index-International (DQI-I). We used regression Generalised Linear Models to determine predictors of diet quality and Classification and Regression Tree (CART) analysis to examine the complex relationships of predictors and identified profiles of sub-groups of older adults that predict diet quality. Results. The median age in this sample (n=468) was 80.0 years (77.0-84.0). Living with others, high deprivation index and a higher BMI were independent predictors of poorer diet quality. With CART analysis, we found that those with a BMI &gt;29 kg/m2, living with others and younger than 80 years were likely to have a lower diet quality. Conclusions: We found BMI, living arrangement and socioeconomic status were independent predictors of diet quality in pre-frail older adults, with BMI being the most important variable in this sample when the interacting relationships of these variables were considered. Future research is needed to determine the similarities and/or differences in the profile of subgroups of older adults with poorer diet quality.

The optimization of the production process of metal mines has been traditionally driven only by economic benefits while ignoring resource efficiency. However, it has become increasingly aware of the importance of resource efficiency since mineral resource reserves continue to decrease while the demand continues to grow. To better utilize the mineral resources for sustainable development, this paper proposes a multi-objective optimization model of the production process of metal mines considering both economic benefits and resource efficiency. Specifically, the goals of the proposed model are to maximize the profit and resource utilization rate. Then, the fast and elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II) is used to optimize the multi-objective optimization model. The proposed model has been applied to the optimization of the production process of a stage in the Huogeqi Copper Mine. The optimization results provide a set of Pareto-optimal solutions that can meet varying needs of decision makers. Moreover, compared with those of the current production indicators, the profit and resource utilization rate of some points in the optimization results can increase respectively by 2.99% and 2.64%. Additionally, the effects of the decision variables (geological cut-off grade, minimum industrial grade and loss ratio) on objective functions (profit and resource utilization rate) were discussed using variance analysis. The sensitivities of the Pareto-optimal solutions to the unit copper concentrate price were studied. The results show that the Pareto-optimal solutions at higher profits (with lower resource utilization rates) are more sensitive to the unit copper concentrate prices than those obtained in regions with lower profits.