Uncertainties in initial water saturation and early water breakthroughs of un-known sources and paths, which occurred in the low resistivity Lower Haushi sand-stone (LHS) reservoir at the beginning of oil production, imply that the bypassed oil can yet remain in the reservoir. In addition, the upper part of LHS is a tight oil reser-voir, which can still contain a significant amount of unrecovered oil. This opens the opportunity to produce the remaining oil instead of abandoning this reservoir. Low resistivity can exaggerate water saturation, leading to misinterpretation and premature water flooding due to inadequate oil-water contrast. Our analysis revealed a correlation between low resistivity and robust porous network connectivity, along-side elevated formation water salinity in highly porous layers. In regions of high po-rosity, sufficient oil-water contrast facilitates precise water saturation determination, affirming oil presence in all wells. However, within tight oil zones, near-complete wa-ter saturation contradicts actual oil presence. Factors contributing to saturation un-certainty and water breakthroughs were reassessed. Utilizing a 1:1 verti-cal-to-horizontal permeability ratio derived from core data enhanced simulation alignment with water production rates. Investigation into the impact of relative per-meabilities on water production was conducted. Water saturation maps were gener-ated to pinpoint remaining oil reserves. Depletion around wells is evident in lower po-rous regions, while oil persists across the entire tight reservoir, notably in two unex-plored sections.

Three-dimensional (3D) facies and petrophysical models were generated from previously published data of carbonate strata in the Dam Formation (eastern Saudi Arabia) to quantitatively investigate, describe, understand, model, and predict the permeability anisotropy of tidal flat carbonate within a sequence stratigraphic framework. The resulting 3D models were used to conduct fluid flow simulations to demonstrate how permeability anisotropy influences the production of hydrocarbons and ultimately affects decisions concerning future drilling in the exploration and development of carbonate reservoirs that have tidal flat strata. The constructed 3D facies model consists of four lithofacies associations, two of which were grain-dominated associations and two of which were mud-dominated associations. These lithofacies associations varied spatially in four reservoir zones (zones 1 to 4), which represent two fourth-order sequences in the uppermost part of the Dam Formation. Zones 1 and 3 consist of transgressive parasequences, and zones 2 and 4 consist of the regressive parasequences of these sequences. The 3D porosity and permeability models have a coherent match with the distribution of the lithofacies and the stratigraphic framework of the Dam Formation. The results suggested that the permeability anisotropy in zones 1 and 3 is controlled by the occurrence of the grain-dominated lithofacies associated with tidal flat channels. This lithofacies association overlies the sequence boundaries of sequences 1 and 3, forms reservoir bodies with relatively high permeability values, and is elongated perpendicular to the shoreline of the depositional environments. In contrast, permeability anisotropy in zones 2 and 4 is thought to be controlled by the occurrence of the grain-dominated lithofacies associated with the oolitic shoal. This lithofacies association overlies the maximum flooding surface of sequences 2 and 4, forms reservoir bodies with relatively high permeability values, and is elongated parallel to the shoreline of the depositional environments. Fluid flow simulation results suggested that the trend in hydrocarbon production from the constructed 3D models depends on permeability anisotropy in each reservoir zone. Thus, recognizing trends in permeability anisotropy, which might be predicted using sequences stratigraphy, could help to identify potential areas for future drilling.

Polarimetry is used to determine the Stokes parameters of a laser beam. Once all four S0,1,2,3 parameters are determined, the state of polarisation is established. Upon reflection of a laser beam with the defined S polarisation state, the directly measured S parameters can be used to determine the optical properties of the surface, which modified the S-state upon reflection. Here, we demonstrate polarimetry for the determination of surface anisotropies related to birefringence and dichroism from different materials, which have a common feature of linear patterns of different alignments and scales. It is shown that polarimetry in the back-reflected light is complementary to ellipsometry and four-polarisation camera imaging.

Blood vessels are essential for maintaining tumor growth, progression, and metastasis, yet the tumor vasculature is under a constant state of remodeling. Since the tumor vasculature is an attractive therapeutic target, there is a need to predict the dynamic changes in intratumoral fluid pressure and velocity which occur across the tumor microenvironment (TME). The goal of this study is to get insight into perfusion anisotropy within lung tumors. To achieve this goal, we used the perfusion marker Hoechst 33342 and vascular endothelial marker CD31 to stain tumor sections from C57BL/6 mice harboring Lewis Lung Carcinoma tumors on their flank. Vasculature, capillary diameter, and permeability distribution were extracted at different time points along the tumor growth curve. A computational model was generated applying a unique modeling approach based on the smeared physical fields (Kojic Transport Model, KTM). KTM predicts spatial and temporal changes in intratumoral pressure and fluid velocity within the growing tumor. Anisotropic perfusion occurs within two domains - capillary and extracellular space. Anisotropy in tumor structure causes nonuniform distribution of pressure and fluid velocity. These results provide insights regarding local vascular distribution for optimal drug dosing and delivery to better predict distribution and duration of retention within the TME.

Fluorescein anisotropy, which is a widely used technique to study the folding state of proteins or affinity of ligands, is used in the present work to study the temperature sensing of fluid in a microchannel, by adding fluorophore in the fluid. Fluorescein was used as a temperature probe, while glycerol-aq. ammonia was used as a working fluid. Fluorescence anisotropy of fluorescein were measured by varying various parameters. Apart from this, a comparison of fluorescence anisotropy and fluorescence intensity is also performed.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Gas-water relative permeability curve is the foundation of gas reservoir dynamic analysis and numerical simulation. It is generally obtained through gas displacing water experiment. Referring to the existing national standards, gas-water relative permeability test is carried out for low-permeability and tight sandstone. The flow is discontinuous and the curve smoothness is poor, which affects the application of gas-water relative permeability curve. Based on the comparative analysis of a large number of mercury injection and NMR experimental results of low-permeability and tight sandstone, a method to characterize the throat radius distribution of low-permeability tight sandstone based on NMR T2 spectrum is explored. Combined with high-speed centrifugal experiment, the calculation formulas of core water saturation, phase relative permeability of gas-water under different centrifugal force are established. A new method of "nuclear magnetic resonance + high-speed centrifugation" for gas-water relative permeability curve test of low-permeability and tight sandstone is formed, and the test is carried out on Sulige low-permeability tight sandstone core. The results show that: (1) The shape of cumulative distribution curve of throat radius by mercury injection method is basically consistent with that of T2 relaxation time by NMR, and there is a good corresponding relationship between them. (2) The centrifugation process is similar to the gas displacing water process. With the decrease of water saturation, water centrifugation in rock core becomes more and more difficult until it become irreducible. (3) The test process of the new method is unified and standard and up to 6 cores can be tested at the same time. The calculation results of water saturation and relative permeability curve are reliable and the integral curve is smooth, which greatly improves the test efficiency of gas-water relative permeability curve in low-permeability and tight sandstone. The new method can be widely used to study the gas-water two-phase seepage law in low-permeability and tight sandstone gas reservoir.

Soil transverse isotropy results in different stiffness characteristics in the horizontal and vertical directions. However, the effect is usually neglected in the seismic motion analysis. In this study, an equivalent linear anisotropic soil model was established based on the finite element method and investigated the impact of anisotropic parameters on ground motion at the site under various seismic wave inputs. It is found that the anisotropic parameters have a more significant effect for the seismic waves with the dominant frequency closer to the fundamental frequency of the site. As an example, the soil dynamic parameters in Shanghai Yangshan Port were calibrated by a series of bending elements, resonance columns, and cyclic triaxial tests. The influences of anisotropy on the peak ground acceleration (PGA) and response spectrum are studied for Yangshan Port. Addi-tionally, the standard design response spectra considering the soil anisotropy were provided. A comparison reveals that the existing isotropic design response spectrum may lead to dangerous seismic design for the structures at Yangshan port.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

Hybrid metal-organic compounds as relatively new and prosperous magnetoelectric multiferroics provide opportunities to improve the polarization, magnetization and magneto-electric coupling at the same time, which usually have some limitations in the common type-I and type-II multiferroics. In this work we investigate the crystal of guanidinium copper(II) formate [C(NH2)3]Cu(HCOO)3 and give novel insights concerning the structure, magnetic, electric and magneto-electric behaviour of this interesting material. Detailed analysis of crystal structure at 100 K is given. Magnetization points to the copper(II)-formate spin-chain phase that becomes ordered below 4.6 K into the canted antiferromagnetic (AFM) state, as a result of super-exchange interaction over different formate bridges. The performed ab-initio colinear density functional theory (DFT) calculation confirm the AFM-like ground state as a first approximation and explain the coupling of spin-chains into the AFM ordered lattice. In versatile measurements of magnetization of a crystal, including transverse component besides the longitudinal one, very large anisotropy is found that might originate from canting of the coordination octahedra around copper(II) in cooperation with the canted AFM order. With cooling down in zero fields the generation of spontaneous polarization is observed step-wise below 270 K and 210 K and the effect of magnetic field on its value is observed also in the paramagnetic phase. Measured polarization is somewhat smaller than the DFT value in the c-direction, possibly due to twin domains present in the crystal. The considerable magneto-electric coupling below the magnetic transition temperature is measured with different orientations of the crystal in magnetic field, giving altogether the new light onto the magneto-electric effect in this material.

This study aims to investigate the interfacial tension, emulsion stability, and the impact on oil displacement effectiveness of mixed systems containing nonionic surfactants and amphoteric surfactants at different ratios. To achieve this, three different emulsion stability formulations were prepared by mixing betaine and nonionic surfactants in ratios of 1:1, 3:2, and 3:1 respectively. By adjusting the proportions of betaine and nonionic surfactants, variations in interfacial tension and emulsion formation among the three mixed systems were studied to analyze the mechanism of interaction between betaine and nonionic surfactants and evaluate their effects on crude oil displacement and enhanced oil recovery in reservoirs. Subsequently, microscopic and macroscopic oil displacement experiments were conducted on the three mixed systems, along with experiments on emulsion flow resistance. The aim was to verify the oil displacement effectiveness of different mixed systems and further understand their potential applications in reservoirs. By comprehensively analyzing the experimental results, optimal ratios and conditions for the mixed systems were determined. The experimental results indicate that the emulsification system formed by mixing betaine and nonionic surfactants at a ratio of 3:1 achieves molecular synergies through electrostatic interactions and mixed adsorption with betaine, resulting in a compact arrangement of interface membranes and demonstrating a synergistic effect in reducing interfacial tension to an ultra-low value of 10 -4 mN/m. Additionally, as the proportion of betaine surfactant increases, the viscosity of the aqueous phase liquid film increases, the rate of thinning of the liquid film slows down, the rate of water release slows down, and the stability of the emulsion increases. Microscopic oil displacement experiments verified that the three mixed systems increase oil washing efficiency through low interfacial tension and emulsification stripping action, thereby increasing the oil displacement mechanism's coefficient. Emulsion flow resistance experiments demonstrated that as the proportion of betaine surfactant increases, the system exhibits better plugging ability. However, macroscopic oil displacement experiments revealed differences in compatibility between different emulsion stability solutions and rocks with different permeabilities. The mixed system of betaine and nonionic surfactants at a ratio of 3:1 exhibits the best emulsification plugging ability in rocks with a permeability of 109mD, while the 1:1 mixed system performs best in rocks with a permeability of 12mD. This holds significant theoretical and practical significance for reservoir development and enhanced production.

Nickelate superconductors, R1-xAxNiO2 (where R is a rare earth metal and A = Sr, Ca), experimentally discovered in 2019 exhibit many unexplained mysteries as the existence of a superconducting state with Tc (up to 18 K) in thin films and its absence in bulk materials. Another unexplained mystery of nickelates is their temperature-dependent upper critical field, Bc2T, which can be nicely fitted to two-dimensional (2D) models; however the deduced film thickness, dsc,GL, exceeds the physical film thickness, dsc, by a manifold. To address the latter, it should be noted that 2D models assume that dsc is less than the in-plane and out-of-plane ground state coherence lengths, dsc<ξab0 and dsc<ξc0, respectively, and, in addition, that the inequality ξc0<ξab0 satisfies. Analysis of the reported experimental Bc2T data showed that at least one of these conditions does not satisfy for R1-xAxNiO2 films. This implies that nickelate films are not 2D superconductors, even despite though that the superconducting state is observed only in thin films. Based on this, here we proposed analytical three dimensional (3D) model for global data fit of in-plane and out-of-plane Bc2T in nickelates. The model is based on a heuristic expression for temperature dependent coherence length anisotropy: γξT=γξ01-1a×TTc, where a>1 is a unitless free-fitting parameter. The proposed expression for γξT, perhaps, has a much broader application because it has been successfully applied to bulk pnictide and chalcogenide superconductors.

Two anisotropic exact Bianchi type I solutions of Einstein’s field equations that generalize the isotropic ΛCDM universe model, are used to investigate the Hubble tension. It is shown that the cosmic anisotropy as deduced from the Planck measurements of the fluctuations in the temperature of the cosmic microwave background radiation, is ten billion times too small to solve the Hubble tension.

We have investigated the canine of olive flounder in terms of the nonlinear optical signals of two-photon excitation autofluorescence (2PEF) and second harmonic generation (SHG), whereby two kinds of nonlinear microscope images of the canine were obtained using ~140 femtosecond pulses. For increasing excitation power of laser pulses, a photobleaching effect was found to be significant in the red and green ranges of autofluorescence, where a double-exponential decay of the intensity occurs within hundreds of second due to collagen fluorophores in the canine. In the blue range of autofluorescence, the photobleaching is suppressed due to an energy conversion of the incident laser pulse to SHG signal. As a result, the signal in blue range remains constant for long term exposure to laser. We have also found that the SHG intensity depends on the orienta-tion of linearly polarized excitation, and the optical anisotropy of SHG can be attributed to the collagen alignment of canines.

Monolayered MoS₂ is energetically most stable when it has a 1H phase, but 1H to 1T phase transition (1H→1T) is easily realized by various ways. Even though magnetic moment is not observed during 1H1T, 0.049 µB/MoS₂ is obtained in local 1T phase; 75% 2H and 25% 1T phases are mixed in (2×2) supercell. Furthermore, non-negligible magnetocrystalline anisotropy (MCA) energy is occured. Most magnetic moment as well as MCA are originated by 1T phased Mo atom5 in the supercell, while electronic structures of other atoms are similar to non-magnetic. Due to this, magnetic/non-magnetic boundary is created in the monolayered MoS2. Our result suggests that MoS₂ can be applied for spintronics such as a spin transistor.

Polarisation analysis in the mid-infrared fingerprint region was carried out on thin (∼1μm) Si and SiO2 films evaporated via glancing angle deposition (GLAD) method at 70∘ to the normal. Synchrotron-based infrared microspectroscopic measurements were carried out on the Infrared Microspectroscopy (IRM) beamline at Australian Synchrotron. Specific absorption bands, particularly Si-O-Si stretching vibration, was found to follow the angular dependence of ∼cos2θ, consistent with the absorption anisotropy. This unexpected anisotropy stems from the enhanced absorption in nano-crevices, which have orientation following the cos2θ angular dependence as revealed by Fourier transforming the image of the surface of 3D columnar films and numerical modeling of light field enhancement by sub-wavelength nano-crevices.

Nanostructured carriers have been widely used in pharmaceutical formulations for dermatological treatment. They offer targeted drug delivery, sustained release, improved biostability, and low toxicity, usually presenting advantages over conventional formulations. Due to its large surface area, small size and photothermal properties, graphene oxide (GO) has the potential to be used for such applications. Nanographene oxide (GOn) presented average sizes of 197.6 ± 11.8 nm, and a surface charge of -39.4 ± 1.8 mV, being stable in water for over 6 months. 55.5 % of the mass of GOn dispersion (at a concentration of 1 mg mL-1) permeated the skin after 6 h of exposure. GOn dispersions have been shown to absorb near-infrared radiation, reaching temperatures up to 45.7 °C, within mild photothermal therapy temperature range. Furthermore, GOn in amounts superior to those which could permeate the skin were shown not to affect human skin fibroblasts (HFF-1) morphology or viability, after 24 h of incubation. Due to its large size, no skin permeation was observed for graphite particles in aqueous dispersions stabilized with Pluronic P-123 (Gt-P-123). Altogether, for the first time, GOn potential as a topic administration agent and for delivery of photothermal therapy has been demonstrated.

The current study aims to develop a methodology for obtaining topology-optimal structures made of short fiber-reinforced polymers, which include the fluid-structure interaction. Accounting for the molding process during the internal iterations of topology optimization makes it possible to enhance the weight efficiency of structures—a crucial aspect, especially in aerospace. Anisotropy is considered through the fiber orientation tensor, which is modeled by solving the plastic molding equations for non-Newtonian fluids, and then introduced as a variable of the stiffness matrix during the structural analysis. The materials used were non-linearly modeled using an exponential-and-linear hardening law. The evaluation of weight efficiency in structures composed of short-reinforced composite materials using a dimensionless criterion is addressed. Experimental verification was performed to confirm the validity of the developed methodology. The evidence illustrates that considering anisotropy leads to stiffer structures and structural elements should be oriented in the direction of maximal stiffness. The load-carrying factor can be expressed in terms of failure criteria. The presented multidisciplinary methodology can be used to improve the quality of the design of structures made of short fiber-reinforced composites (SFRC) where high stiffness, high strength, and minimum mass are the primary required structural characteristics.

The latest experimental measurements of cosmic rays (CRs) have discovered a series of anomalies, including the hardening of the nuclear spectra at R ∼200 GV followed by softening at R ∼10 TV and complicated energy dependence of anisotropy from GeV to PeV. Recent works have demonstrated nearby sources are crucial for these anomalies of spectra and anisotropy. In this work, we analyze the contributions of five nearby sources within 1 kpc around solar system to the spectra and anisotropy, finally find out which source is the best candidate source. In the calculation process, we also introduce the anisotropic diffusion of CRs induced by the local interstellar magnetic field (LIMF) nearby the solar system based on spatial-dependent propagation (SDP) model. As a result, we find Geminga SNR source can simultaneously account for CR spectra and anisotropy, whereas the other sources can not . Measurements of CR anisotropy and spectra by experiments such as LHAASO and HAWC are expected to test this scenario in the near future.

Evaluation of drug permeability using cell monolayers is an important in vitro assay in the process of drug development, to identify compounds with favourable pharmacokinetics that may proceed to in vivo studies. When allowed to differentiate on permeable filters for at least 21 days, monolayers of Caco-2 cells develop morphological and functional properties similar to those of the intestinal epithelium. Permeability through Caco-2 monolayers is thus particularly relevant to assess drug absorption after oral administration. The major drawback of this assay is its very low throughput, with the cell monolayers being used in a single permeability assay. We have previously proposed a protocol to allow the re-use of the Caco-2 monolayer on additional permeability assays during the stable period and shown that cell monolayer integrity is maintained. In this work we evaluate the effect of re-use on the permeability of several reference compounds that permeate through passive pathways and show that the cell monolayers can be re-used twice in additional permeability assays. Preliminary results were also obtained regarding active transport pathways, and a new methodology is proposed to quantify the contribution from passive and active transport. This is a major step towards the full validation of the re-use methodology proposed, which at least triplicates the throughput of this important in vitro assay.

Appling the controlling relative permittivity and permeability in the equations for the gravitational-magnetic-electric field interaction, a very large variation of the gravitational acceleration of the Earth by electric/magnetic field could be arrived at. This conclusion may be supported by some of the experiments for the gravitational effect of superconductivity.

The activity of the mitochondrial Permeability Transition Pore, mPTP, a highly regulated multi-component mega-channel, is enhanced in aging and in aging-driven degenerative diseases. mPTP activity accelerates aging by releasing large amounts of cell-damaging Reactive Oxygen Species, Ca2+ and NAD+. The various pathways that control the channel activity, directly or indirectly, can therefore either, inhibit, or accelerate aging, retards, or enhance the progression of aging-driven degenerative diseases, and determine lifespan and healthspan. Autophagy, a catabolic process that removes and digests damaged proteins and organelles protects the cell against aging and disease. However, the protective effect of autophagy depends on mTORC2/SKG1 inhibition of mPTP. Autophagy is inhibited in aging cells. Mitophagy, a specialized form of autophagy, which retards aging by removing mitochondrial fragments with activated mPTP, is also inhibited in aging cells, and this inhibition leads to increased mPTP activation, which is a major contributor to neurodegenerative diseases, such as Alzheimer’s and Parkinson’s Diseases. The Increased activity of mPTP in aging turns autophagy/mitophagy into a destructive process leading to cell aging and death. Several drugs and lifestyle modifications that enhance healthspan and lifespan enhance autophagy and inhibit the activation of mPTP. Therefore, elucidating the intricate connections between pathways that activate and inhibit mPTP, in the context of aging and degenerative diseases, could enhance the discovery of new drugs and lifestyle modifications that slow aging and degenerative disease.

In this study, the relationship between air diffusivity and permeability in cementitious materials was investigated. First, we derived an equation to correlate air diffusivity and permeability in a straight circular tube. Then, we reviewed existing studies that measured both air diffusivity and permeability and compared reported data and calculated values to verify the applicability of the derived equation to cementitious materials. Although a correction factor was not used, the two sets of data showed good agreement quantitatively. This indicates that the derived equation can be applied to cementitious materials including concrete, and measured air diffusivity can be converted to permeability of concrete and vice versa using the derived equation.

In this perspective, we give an overview of several less explored structural and optical characterisation techniques useful for biomaterials. New insights into the structure of natural fibres such as spider silk can be gained with minimal sample preparation. Electromagnetic radiation (EMR) over a broad range of wavelengths (from X-ray to THz) provides information of the structure of the material at cor- respondingly different length scales (nm-to-mm). When the sample features, such as the alignment of certain fibres, cannot be characterised optically, polarisation analysis of the optical images can provide further information on feature alignment. The 3D complexity of biological samples necessitates that there be feature measure- ments and characterisation over a large range of length scales. We discuss the issue of characterising complex shapes by analysis of the link between the color and struc- ture of spider scales and silk. For example, it is shown that the green-blue color of a spider scale is dominated by the chitin slab’s Fabry-P ́erot type reflectivity rather than the surface nanostructure. The use of a chromaticity plot simplifies complex spectra and enables quantification of the apparent colors. All the experimental data presented herein are used to support the discussion on the structure-color link in the characterisation of materials.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

Band structure calculations using the spin-polarized relativistic Korringa-Kohn-Rostoker (SPRKKR) band structure method have been performed to determine the intrinsic magnetic properties (magnetic moments, magneto-crystalline anisotropy -MAE and Curie temperatures) of the Fe5-x-yCoxMySiB2 (M = Re, W) alloys. The general gradient approximation for ex-change-correlation potential and the atomic sphere approximation (GGA ASA) have been em-ployed. Previous studies showed that the Co doping is turning the in-plane into axial anisotropy for a certain doping range, whilst the 5d doping enables a strong spin-orbit coupling of Fe-3d and M-5d states which is needed to enhance the MAE. The theoretical calculations aim to find the dependence of the anisotropy constant K1 for combined Co and M doping, building a two-dimensional (2D) map of K1 for 0 ≤ x ≤ 2 and 0 ≤ y ≤ 1. Similar theoretical 2D maps for magnetization and Curie temperature vs. Co and M content (M = W and Re) have been built, allowing to select alloy compositions with enhanced values of uniaxial anisotropy, magnetization and Curie temperature. Magnetic properties of Fe4.1W0.9SiB2 alloy that meets the selection criteria for axial anisotropy K1 > 0.2 meV/f.u., Curie temperature Tc > 800 K determined by mean field approach and magnetization µ0Ms > 1 T are discussed.

This work is a natural extension of the author’s previous work: “Multiple scattering theory for heterogeneous elastic continua with strong property fluctuation: theoretical fundamentals and applications” (arXiv:1706.09137 [physics.geo-ph]), which established the foundation for developing multiple scattering model for heterogeneous elastic continua with either weak or strong fluctuations in mass density and elastic stiffness. Polycrystalline material is another type of heterogeneous materials that widely exists in nature and extensively used in industry. In this work, the corresponding multiple scattering theory for polycrystalline materials with randomly oriented anisotropic crystallites is developed. To validate the theory, the theoretical results for a series of materials such as OFHC copper, 304 stainless steel, and Inconel 600 are compared to experimental measurements and the numerical results obtained using finite element simulations. Detailed analysis shows that the new theory is capable of predicting the dispersion and attenuation of polycrystals with satisfactory accuracy. The results also show the new model can give an estimate on the average grain size with a relative error equal to or less than ten percent. As applications in ultrasonic nondestructive evaluation, we calculated the dispersion and attenuation coefficient of one of the most important polycrystalline materials in aeronautics engineering: high-temperature titanium alloys. The effects of grain symmetry, grain size, and alloying elements on the dispersion and attenuation behaviors are examined. Key information is obtained which has significant implications for quantitatively evaluating the average grain size, monitoring the phase transition, and even estimating gradual change in chemical composition of titanium components in gas turbine engines. For applications in seismology, the velocities and Q-factors for both hexagonal and cubic polycrystalline iron models for the Earth’s uppermost inner core are obtained in the whole frequency range. Using the realistic material parameters of iron under the high temperature and high-pressure conditions calculated from ab initio simulations, the numerical results show that the Q-factors range from 0.001 to 0.05, which shows good agreement with that inferred from real seismic data. The new model predicts the velocity of longitudinal waves varies between ± 1% to ± 5 % relative to the Voight average velocity, while the velocity of transverse waves varies from ± 10% to ± 20%, which gives promising explanation to the abnormally slow transverse velocity observed in practical measurements. The numerical results support the conjecture that the Earth’s uppermost inner core is a solid polycrystalline medium. The comprehensive numerical examples show the new model is capable of capturing the most important scattering features of both ultrasonic and seismic waves with satisfactory accuracy. This work provides a universal, quantitative model for characterization of a large variety of polycrystalline materials. It also can be extended to incorporate more complicated microstructures, including ellipsoidal grains with or without textures, and even multi-phase polycrystalline materials. The new model demonstrates great potential of applications in ultrasonic nondestructive evaluation and inspection of aerospace and aeronautic structures. It also provides a theoretical framework for quantitative seismic data explanation and inversion for the material composition and structural formations of the Earth’s inner core.

We have performed first-principles calculations to study the interfacial exchange coupling and magnetocrystalline anisotropy (MCA) energy in a SmCo₅/Sm₂Co₁₇ multilayer model systems. The phase of SmCo₅ and Sm₂Co₁₇ stacking along (0001) direction are structurally well matched. The atomic structure, including the alignment and the separation between layers, were firstly optimized. Then the non-collinear magnetic structures were calculated to explore the exchange coupling across the interface and the variation of MCA energy. We found that the inter-phase exchange coupling strength, rotating behavior and MCA energy are strongly dependent on the atomic thickness of the SmCo₅ and Sm₂Co₁₇ phase.

Current progress in the prediction of mechanical behavior of solids requires understanding of spatiotemporal complexity of plastic flow caused by self-organization of crystal defects. It may be particularly important in hexagonal materials because of their strong anisotropy and combination of different mechanisms of plasticity, such as dislocation glide and twinning. These materials often display complex behavior even on the macroscopic scale of deformation curves, e.g., a peculiar three-stage elastoplastic transition, the origin of which is a matter of debates. The present work is devoted to a multiscale study of plastic flow in α-Ti, based on simultaneous recording of deformation curves, 1D local strain field, and acoustic emission (AE). It is found that the average AE activity also reveals three-stage behavior, but in a qualitatively different way depending on the crystallographic orientation of the sample axis. On the finer scale, the statistical analysis of AE events and local strain rates testifies to an avalanche-like character of dislocation processes, reflected in power-law probability distribution functions. The results are discussed from the viewpoint of collective dislocation dynamics and are confronted to predictions of a recent micromechanical model of Ti strain hardening.

We studied the performance of a quantum magnetic Stirling cycle that uses a working substance composed of two entangled antiferromagnetic qubits (J) under the influence of an external magnetic field (Bz) and an uniaxial anisotropy field (K) along the total spin in the y-direction. The efficiency and work were calculated as a function of Bz and for different values of the anisotropy constant K given hot and cold reservoir temperatures. The anisotropy has been shown to extend the region of the external magnetic field in which the Stirling cycle is more efficient compared to the ideal case.

Hantavirus cardiopulmonary syndrome (HCPS) is characterized by capillary leak, pulmonary edema (PE) and shock that leads to death in up to 40% of patients. Treatment is supportive, including mechanical ventilation (MV) and extracorporeal membrane oxygenation (ECMO). Hemodynamic monitoring is critical to titrate therapy and to decide ECMO support. Transpulmonary thermodilution (TPTD) provides hemodynamic and PE data that has not been systematically used to understand HCPS pathophysiology. We identified 11 HCPS patients monitored with TPTD; 5 on MV, 3 on ECMO. We analyzed 133 measurements to describe the hemodynamic pattern and its association to PE. The main findings were reduced stroke volume, global ejection fraction (GEF) and preload parameters associated to increased extravascular lung water and pulmonary vascular permeability compatible with hypovolemia, myocardial dysfunction and increased permeability PE. Lung water correlated positively with heart rate (HR, r=0.20) and negatively with mean arterial pressure (r=-0.27) and GEF (r=-0.36), suggesting that PE is linked to hemodynamic impairment. Pulmonary vascular permeability correlated positively with HR (r=0.31) and negatively with cardiac index (r=-0.49), end-diastolic volume (r=-0.48) and GEF (r=-0.40), suggesting that capillary leak contributes to hypovolemia and systolic dysfunction. In conclusion, TPTD data suggests that in HCPS patients, increased permeability leads to PE, hypovolemia and circulatory impairment.

Correlations between the air permeability coefficient and various pore structure indicators in cementitious materials were examined to determine the pore structure indicator that best evaluated air permeability using data from previous studies of air permeabilities and pore structures. The determination coefficients of air permeability with total pore volume, critical pore diameter, and ordinary threshold pore diameter were low, although these have often been used as indicators. The median and threshold pore diameters obtained by percolation theory showed high determination coefficients. The equation using the threshold pore diameter better estimated the air permeability coefficient than the Katz–Thompson equation.

To understand the relationship between water permeability and the pore structure of cementitious materials, literature that studied both water permeability and the pore structure are reviewed, and their correlation is studied. Although the majority of this data is for cement paste, mortar, concrete, and cemented soil are also included. Based on this study, it is established the determination coefficient between water permeability and the total pore volume is very low; however, those between water permeability and the critical, threshold, and median pore diameters, respectively, are moderate. On the other hand, the threshold pore diameter, derived based on the percolation theory, exhibits a very high determination coefficient. The calculated water permeability, using the Katz and Thompson equation, agrees with the reported water permeability quantitatively to a certain level, but is overestimated.

The paper shows that it is possible to obtain reliable information on the dependence of radial distribution of longitudinal birefringence in glass cylindrical elements with radial distribution of refractive index (GRIN lenses) on the basis of transverse polarization tomography data of residual stresses. This does not require complicated procedures of sample preparation, as is necessary in the case of longitudinal translucency measurements. The approach developed was verified in the experiments with a set of different GRIN lenses formed with ion exchange technique, and the closeness of the data obtained from transversal and conventional longitudinal transmission measurements was demonstrated.

In this paper, we considered two phenomena in acoustically excited aqueous solutions of a strong electrolyte. These are the well-known Debye ionic vibrational potential (IVP), and radiofrequency anisotropy we discovered earlier , apparently, for the first time. Since both occur due to the accelerated motion of the solution, we have tried to combine them in one simple model. We have established that for a polarized UHF radio wave passed through a NaCl aqueous solution excited by an acoustic pulse the rotation angle of its vector E is proportional to the integral of the square of the observing IVP over time. An equivalent electrical circuit simulating the observed phenomena has been proposed and tested for physical feasibility. Several arguments are given in favour of the fluid-gyroscopic mechanism of RF anisotropy-related effects. We also found out that the IVP is practically independent of the vibrational velocity for frequencies below 10 kHz and it tends to zero at zero frequency. The latter is consistent with the law of conservation of energy but contradicts the incomplete existing theory.

Consideration of physical processes in the reference frame K' moving relative to the CMB, provided that clocks synchronization in this frame ensures the independence of time from spatial coordinates, leads to the conclusion about the existence in the K' of spatial anisotropy which should manifest itself in the dependence of physical effects on the speed vector V of the frame relative to the CМB. Some of these effects in the fields of electrodynamics and optics are considered. In particular, it is shown that weak magnetic fields proportional to the vector V should exist in this frame around motionless electric charges. Experimental verification, according to our assessment, is apparently possible.

Four-polarisation camera was used to map absorbance of olivine micro-grains before and after high temperature annealing (HTA). It is shown that HTA of olivine xenolith at above 1200∘C in O2 flow makes it magnetised. Different mode of operation of polariscope with polarisation control before and after the sample in transmission and reflection modes was used. The reflection type was assembled for non-transparent samples of olivine after HTA. Sample for optical observation in transmission was placed on an achromatic plastic quarter-wavelength waveplate as a sample holder. Inspection for sample’s birefringence (retardance) as well as absorbance can be made. A best fit of transmitted intensity or transmittance T (hence absorbance A=−log10T) becomes accessible by simple best-fit using only three orientations (from measured four orientations by the camera). When intensity of transmitted light at one of the orientations was very low due to cross-polarised condition (polariser-analyser arrangement), the three-points fit can be used. Three-point fit in transmission and reflection modes was validated for T(θ)=Amp×cos(2θ−2θshift)+offset, where amplitude Amp, offset offset and orientation azimuth θshift are extracted for each pixel via the best fit.

Fractures are present in hydrocarbon reservoirs of different porosity ranges. Seismic anisotropy has been widely used in fracture characterization and shown to be sensitive to background matrix porosities in theoretical studies. An understanding of the effects of background porosity on seismic anisotropy could improve seismic characterization in different fractured reservoirs. Based on synthetic rocks with controlled fractures, we conducted laboratory experiments to investigate the influence background porosity has on P wave anisotropy and shear wave splitting. A set of rocks containing the same fracture density (0.06) with varying porosities of 15.3%, 22.1%, and 30.8% were constructed. P and S wave velocities were measured at 0.5 MHz as rocks were water saturated. Results show that when porosity increased from 15.3% to 22.1%, P wave anisotropy and shear wave splitting exhibit slight fluctuations. However, when porosity continued to increase to 30.8%, P wave anisotropy declined sharply while shear wave splitting stayed nearly constant. The measured results were compared with predictions from equivalent medium theories. Qualitative agreements were found between theoretical predictions and measured results. In Eshelby-Cheng model, the increase of porosity reduces the fracture-induced perturbation in the fracture normal direction, resulting in a lower P wave anisotropy. In Gurevich(2003) model, the increase of porosity can reduce the compressional stiffness in parallel direction to a larger extent than that in perpendicular direction, thus leading to lower P wave anisotropy.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

Cell monolayers, including endothelial and epithelial cells, play crucial roles in regulating the transport of biomolecules to underlying tissues and structures via intercellular junctions. Moreover, the monolayers form a semipermeable barrier across which leukocyte transmigration is tightly regulated. The inflammatory cytokines can disrupt the epithelial and endothelial permeability, thus the reduced barrier integrity is a hallmark of epithelial and endothelial dysfunction related with numerous pathological conditions, including cancer-related inflammation. Therefore, the assessment of barrier function is critical in in vitro models of barrier-forming tissues. This review summarizes the commercially available in vitro systems used to measure the permeability of cellular monolayers. The presented techniques are separated in two large groups: macromolecular tracer flux assays, and electrical impedance measurement-based permeability assays. The presented techniques are briefly described and compared.

This study presents a methodology to fabricate Ti6Al4V cylindrical compacts with a highly porous core and dense shell with the purpose to mimic the bone microstructure. Compacts with different core diameters were obtained by conventionally press and sintering. Large pores were created with the aid of pore formers. Sintering kinetics was determined by dilatometry, whereas characterization was performed by X-ray computed tomography. Also, permeability was evaluated on the 3D microstructure and the mechanical strength was evaluated by compression tests. Results indicated that sintering is constraint by the different densification rates of the porous and dense layers. Nonetheless, defectless compacts were obtained due to neck bonding between Ti6Al4V particles. Large pores were located in the designed core with similar pore size distribution. Permeability increased following a power law as a function of the pore volume fraction. Stiffness of bilayer components was driven by the porous core, meanwhile, the strength resulted from the combination of both layers. Bilayer materials obtained showed a permeability and mechanical properties, as well as admissible strain (σy /E) similar to those of human bones.

Thin Pd-40%Cu films were obtained by the classical melting and rolling method, magnetron sputtering and modified with nanostructured functional coatings to intensify the process of hydrogen transport. The films were modified by electrodeposition according to the classical method of obtaining palladium black and "Pd-Au nanoflowers" with spherical and pentagonal particles, respectively. The experiment results demonstrated the highest catalytic activity (89.47 mA cm–2), good resistance to CO poisoning and long-term stability of Pd-40%Cu films with a pentagonal structured coating. The investigation of the developed membranes in the hydrogen transport processes in the temperature range of 25-300°C also demonstrated high and stable fluxes up to 475.28 mmol s–1 m–2 (deposited membranes) and 59.41 mmol s–1 m–2 (dense-metal membranes), which turned out to be up to 1.5 higher compared to membrane materials with classic niello. For all-metal modified membranes, the increase in flux was up to 7 times, compared with a smooth membrane made of pure palladium, and for deposited films, this difference was several tens of times. The membrane materials selectivity was also high up to 4419. The developed strategy for modifying membrane materials with functional coatings of a fundamentally new complex geometry can shed new light on the development and fabrication of durable and highly selective palladium-based membranes for gas steam reformers.

The lung epithelium regulates gas exchange and is the first line of defense against airborne toxicants and microbial infections. Disruption of the integrity of lung epithelium results in altered permeability and severely impacts normal lung functions. To develop biomarkers of potential harm (BoPH) for assessing adverse health effects of cigarette smoking, we have evaluated lung barrier function. In a single-center, ambulatory, clinical study we measured lung permeability, as the half-life (T1/2) of inhaled 99mTC-DTPA, in 17 subjects consisting of 6 Smokers (SMK), 5 Moist Snuff Consumers (MSC), and 6 Non-Tobacco Consumers (NTC) at three weekly test visits. Smokers, relative to MSC and NTC, exhibited significantly faster clearance of the inhaled probe (shorter T1/2), indicating increased lung permeability. NTC and MSC had comparable clearance times of the inhaled probe (longer T1/2). Least squares regression modeling showed that the variability of the test was minimal and was not significant. Prediction profiling showed that the repeatability of the lung permeability test was robust and was able to differentiate the tobacco product use groups in this study. Thus, altered lung barrier function may serve as a BoPH for assessing the effects of tobacco use.

Doxorubicin (Dox) is a commonly used chemotherapeutic that can adversely affect skeletal muscle, including causing muscle atrophy. Dox is known to induce an event known as mitochondrial permeability transition (MPT) in cardiac muscle and this plays an important role in Dox-mediated cardiac toxicity. Further to this, recent evidence identifies MPT as a mechanism of atrophy in skeletal muscle, suggesting that MPT may underlie some of the Dox-related toxicity in skeletal muscle. To test this hypothesis, we used cultured human primary myotubes, C2C12 myotubes, and single adult mouse flexor digitorum brevis (FDB) muscle fibers in experiments involving Dox treatment with or without inhibitors of MPT. Dox treatment of myotubes caused myonuclear translocation of the mitochondrial protein apoptosis inducing factor (AIF) and increased mitochondrial reactive oxygen species (mROS), consistent with the known consequences of MPT. Furthermore, Dox caused atrophy in C2C12 myotubes grown on patterned plates, human primary myotubes, and single muscle fibers from adult mice. Notably, Dox-induced atrophy could be prevented by a wide variety of agents that inhibit MPT, as well as by inhibiting mROS or Caspase 3. In conclusion, our results indicate that MPT plays an important role in driving Dox-mediated skeletal muscle atrophy.

Abstract: The Saccharomyces cerevisiae mitochondrial unspecific pore (ScMUC) is an uncoupling unspecific pore that shares some similarities with the mammalian permeability transition pore (mPTP). When open, both channels deplete ion and proton gradients across the inner mitochon-drial membrane. However, the role of mPTP is to reversibly open to protect cells against stress. If mPTP remains stuck in the open position the cell dies. In contrast, ScMUC is probably dedicated to deplete oxygen from the medium in order to kill competing organisms. Such O2 depletion would be better achieved if oxidative phosphorylation is at least mildly uncoupled. Still, when oxida-tive phosphorylation is needed ScMUC should be able to close. To test this, the reversible opening and closing of ScMUC in the presence of different effectors was tested in isolated mitochondria from S. cerevisiae. Evaluations were conducted at different incubation times, monitoring the rate of O2 consumption, mitochondrial swelling and the transmembrane potential. It was observed that ScMUC did remain reversibly open for minutes. A low energy charge (ATP/ADP) closed the chan-nel. In addition, high Ca2+ promoted closing and it was a highly powerful effector.

In-situ injection of steam for heating of the subsurface is an efficient method for the recovery of oil and gas from oil shale where permeability typically evolves with temperature. We reported measurements on Jimusar oil shales(Xinjiang, China) at different temperatures to 600℃ and under recreated in situ triaxial stresses to obtain permeability evolution with temperature and stress. Permeability of tight oil shales evolves with temperature to a threshold temperature and peak temperature. The threshold temperature was subjected to triaxial stresses. For Jimusar oil shale, the threshold temperature ranges from 200℃ to 250℃ at ground stress of buried depth of 500m and from 350℃ to 400℃ at buried depth of 1000m. The peak temperature was almost not subjected to triaxial stress and the range is from 450℃ to 500℃ for all Jimusar samples. Pyrolysis plays an important role in permeability evolution and fundamentally changes permeability tendency and magnitude. At high temperature permeability exhibits a little reduction due to stress effect but still remains a high level due to pyrolysis. The above results show that oil shale mass can change from tight porous media into highly permeable media and oil & gas can easily flow through oil shale stratum.

Magnetoelectric sensors based on microelectromechanical cantilevers consisting of TiN / AlN / Ni are investigated using finite element simulations in regard of the anisotropy of the E effect and its impact on the sensor sensitivity. The E effect is derived from the anisotropic magnetostriction and magnetization of single crystalline Nickel. The magnetic hardening of Nickel in saturation is demonstrated for the (110) as well as the (111) orientation. It is shown further, that magnetostrictive bending of the cantilever has a negligible impact on the eigenfrequency and thus sensitivity. The intrinsic E effect of Nickel decreases in magnitude depending on the crystal orientation when integrated into the magnetoelectric sensor design. The transitions of the individual magnetic domain states are found to be the dominant influencing factor on the sensitivity for all crystal orientations. The peak sensitivity was determined to 41.3 T-1 for (110) in-plane orientated Nickel at a magnetic bias flux of 1.78 mT. It is found, that the transition from domain wall shift to domain rotation along the hard axes yields much higher sensitivity than the transition from domain rotation to magnetization reversal. The results achieved in this work show that Nickel as hard magnetic material is able to reach almost identical sensitivities as soft magnetic materials, such as FeCoSiB.

Permeability is a fundamental property of porous media, especially when studying resin transfer within a dense fibrous medium to manufacture composite materials. When the measurement of permeability tensor of composite reinforcements is difficult and time consuming, especially in thick, heterogeneous fibrous structures, a numerical approach based on the calculation of the tensor components on a 3D image of the material can be very advantageous. A new finite element based method proposed in this study allows solving very high-dimensional flow problems while limiting the biases associated with boundary conditions and the small size of the numerical samples addressed. The method is validated against academic test cases and against the results of a recent permeability benchmark exercise. The results emphasize that for heterogeneous and anisotropic microstructures, it is important to perform calculations on large samples using boundary conditions that do not suppress the transverse flows that occur when flow is forced out of the principal directions. Since these are not necessarily known in complex media, the permeability determination method must not introduce bias by generating non-physical flows.

Various empirical models are available to evaluate the temperature effects on relative permeability of the different rock and fluid systems. However, the implementation of limited experimental data points may hinder the applicability of such models to other systems. This study aims to develop new predictive models for k_ro estimation based on multilayer perceptron artificial neural network (MLP-ANN), adaptive neuro-fuzzy inference system (ANFIS), and least squares support vector machine (LSSVM) approaches. A database comprising of 626 data points applied to the model development. The independent variables are temperature, oil viscosity, water viscosity, water saturation ( ), and the absolute permeability. Each variable covers a wide range of variations which increases models’ potential to be applied in various systems with different characteristics. The doubtful experimental data points excluded using a leverage value approach and a sensitivity analysis carried out to determine the quantitative impact of every individual independent variable on the k_ro. Statistical error analyses demonstrated the coefficient of determination (R²) values of 0.985, 0.975, and 0.999 for MLP-ANN, ANFIS, and LSSVM, respectively. The comparative study indicated that the LSSVM had the best performance regarding both graphical and statistical error analyses among the newly proposed models and previously reported models in the literature.

This paper investigates the influence of different vegetation on the permeability of the shallow soil layers of slopes under rainfall infiltration. Firstly, four large slopes are filled in the outdoor natural environment, and the overburdens of the four slopes are Magnolia multiflora, Cynodon dactylon, Magnolia multiflora mixed with Cynodon dactylon, and no vegetation. Secondly, the four slopes are cultivated in the outdoor natural environment for one year. After the vegetation overburdens are matured, the field artificial rainfall test is carried out through the self-developed artificial rainfall device to monitor the water migration law inside the four slopes in real time. Finally, the unsaturated permeability coefficients of the shallow soil layers of slopes are calculated. The results show that the infiltration rate of rainwater in each overburden slope from fast to slow is Magnolia multiflora overburden slope, no vegetation slope, Cynodon dactylon overburden slope, Magnolia multiflora mixed with Cynodon dactylon overburden slope. In the early stage of rainfall, Magnolia multiflora increases the permeability coefficient of the shallow soil layer of the slope, thus weakening the anti-seepage ability of the slope, but the influence of Magnolia multiflora is not obvious in the later stage. Cynodon dactylon and Magnolia multiflora mixed with Cynodon dactylon can significantly reduce the permeability coefficient of the shallow soil layers of the slopes, thereby increasing the anti-seepage ability of the slopes, and the mixed planting of Magnolia multiflora and Cynodon dactylon can minimize the permeability coefficient of the shallow soil of the slope, resulting in the best anti-seepage effect.

There is a growing need for novel in vitro corneal models to replace animal-based ex vivo test in drug permeability studies. In this study we demonstrate a corneal mimetic that models the stromal and epithelial compartments of human cornea. Human corneal epithelial cells (HCE-T) were grown on top of a self-supporting porcine collagen-based hydrogel. Cross sections of the multilayers were characterized by histological staining and immunocytochemistry of zonula occludens-1 protein (ZO-1) and occludin. Furthermore, water content and elastic properties of the synthetized collagen type I-based hydrogels were measured. The apparent permeability coefficient (Papp) values of a representative set of ophthalmic drugs were measured and correlated to rabbit cornea Papp values found in the literature. Multilayered structure of HCE-T cells and expression of ZO-1 and occludin in full thickness of multilayer were observed. The hydrogel-based corneal model exhibited excellent correlation to rabbit corneal permeability (r=0.96), whereas insert-grown HCE-T multilayer was more permeable and the correlation to the rabbit corneal permeability was lower (r=0.89). The hydrogel-based human corneal model predicts the rabbit corneal permeability more reliably in comparison to HCE-T cells grown in inserts. This in vitro human corneal model can be successfully employed for drug permeability tests whilst avoiding ethical issues and reducing costs.

The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.

A major parameter controlling the extent and rate of oral drug absorption is permeability through the lipid bilayer of intestinal epithelial cells. Here, a biomimetic artificial membrane permeability assay (Franz-Bampa) was validated using Franz cells apparatus. Both high and low permeability drugs (metoprolol and mannitol, respectively) were used as external standards. Biomimetic properties of Franz-Bampa were also characterized by electron paramagnetic resonance spectroscopy (EPR). Moreover, the permeation profile for the 14 BCS class I-IV drugs cited in the FDA guidance (including other drugs as acyclovir, cimetidine, diclofenac, ibuprofen, piroxicam, and trimethoprim) were measured across Franz-Bampa. Apparent permeability (Papp) was compared to literature fraction dose absorbed in humans (Fa%). Papp in Caco-2 cells and Corti artificial membrane were likewise compared to Fa% to assess Franz-Bampa performance. Mannitol and metoprolol Papp values across Franz-Bampa were lower (3.20 x 10-7 and 1.61 x 10-5 cm/s, respectively) than those obtained across non-impregnated membrane (2.27 x 10-5 and 2.55 x 10-5 cm/s, respectively), confirming lipidic barrier resistivity. Performance of the Franz cell permeation apparatus using an artificial membrane showed similar log linear correlation (R2 = 0.664) with Fa%, as seen for Papp in Caco-2 cells (R2 = 0.805). Data support the validation of the Franz-Bampa method for use during drug discovery process.

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

The controls of depositional environments on reservoir quality have been evaluated in terms of porosity and permeability of the Gabo Field, Niger Delta, Nigeria. Data used in this research include Well logs, Core data and photos, and grain size analysis for Wells 51 and 52 in the study area. Standard methods as applicable in petrophysical and sedimentological analysis has been adopted. Thirteen reservoir units have been identified in wells 51 and 52 which had 5 reservoirs cored each. The lithofacies units of the identified reservoirs across the study area, comprise pebbly sands, coarse -, medium -, fine- and very fine-grained sands, sandy mud, silty sands and heteroliths. The heteroliths – very fine-grained silty muds are highly bioturbated. Ophiomorpha and skolithos are the major trace fossils with sedimentary structures (ripple lamination, wavy lenticular and planar beds, cross bedded sands, coarsening and fining upward). The facies associations interpreted for the study area are Channel and Coastal barrier systems and the environment of deposition as distributary channel, upper and lower shoreface. The sedimentary processes that deposited facies ranged from high energy regimes, reworking by waves to low energy with periodic influx of silts and muds. The average porosity and permeability for reservoirs in Well 51 is 16.7% and 1317 Md, reservoirs in Well 52 is 28.2% and 2330Md whereas porosity range for the study area is 2% - 32% and permeability is 1.2 – 10600 Md. The reservoir quality reservoir of the sand units in Well 51 (7, 9 and 13) and Well 52 (5, 7, 9, 11 and 13) is excellent - good, this is because of the dynamics environments of deposition (upper shoreface and distributary channel) as well as the mechanisms that play out during deposition such as bioturbation, sorting, sedimentary structures formed. Whereas the poor quality across the reservoirs especially the lower shoreface and prodelta facies is as result of lack bioturbation, connectivity, multiplicity of burrows that may have been plugged by clay and intercalation of shale and sand (heteroliths). This research has shown that environments of deposition have direct influence the reservoir quality in terms of porosity and permeability.

Abstract: Comparing outcrop data to laboratory results is important to verify and validate experiments of analogue and reservoir materials especially regarding conditions for deformation experiments. This is important better understand highly complex carbonate reservoir strata and their response to changes in subsurface conditions, reducing subsurface uncertainty. This study develops methods to allow for a more straightforward comparison of outcrop data (m-scale) with experimentally created fracture arrays developed in cylindrical samples (cm-scale). The main objective is to assess usefulness of experimentally-produced fracture networks as analogues for subsurface structures, typically at the meter and above scale by developing new techniques to use the lab deformation. It analyses key characteristics of laboratory-induced fracture networks by adapting scanline methods to use with x-ray tomography (XRT) images to allow for comparison with outcrop and field data. To test and verify these new methods two low permeability carbonate samples were used for deformation testing and analysis. Applying the different scanline methods we show that they can be used to analyse lab induced fractures (mm to cm-scale) identified in XRT images for comparison with outcrop data (m-scale). In addition, these methods also allow for quantification of fracture network attributes e.g. fracture spacing, fracture apertures, orientation. This new data bridges the gap between micro-scanlines using thin sections and outcrop scanlines.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

This research evaluated the role and feasibility of the granular nanocellulose particles (GNC) from sugarcane bagasse obtained from enzymatic hydrolysis in reducing lipid digestibility and permeability in the in vitro simulated gastrointestinal (GI) system. GNC concentration (0.02%, w/v) had significantly affected the released free fatty acid (FFA) reduction of approximately 20%. The Pick-ring emulsion of the GNC and olive oil simulation mixture revealed higher oil droplet size distribution and stability in the initial stage than the vortexed mixture formation. The difference in particle size distribution and zeta potential of the ingested GNC suspension and GNC-olive oil emulsion were displayed during the in vitro gastrointestinal simulation. GNC particles interacted and distributed surrounding the oil droplet leading to the interfacial emulsion. The GNC concentration (0.01-0.10%, w/v) showed low toxicity on the HIEC-6 cell, ranging from 80.0 to 99% of cell viability. The release of FFA containing the ingested GNC suspension and GNC-olive oil emulsion was about 30% reduction compared to without GNC digest solution. The FFA and triglyceride permeability through the HIEC-6 intestinal epithelium monolayer were deceased in the digesta containing the ingested GNC and emulsion. This work indicated that GNC represented a significantly critical role and properties in the GI tract and reduced lipid digestion and absorption. This GNC could be utilized as an alternative food additive or supplement in fatty food for weight control due to their inhibiting lipid digestibility and assimilation.

The vacuum preloading method effectively strengthens the soft soil foundations with vertical drainage, which will produce a smear effect when laying sand drains. Meanwhile, the seepage of pore water and soil deformation during consolidation exhibits nonlinear characteristics. Therefore, based on Gibson's 1D large strain consolidation theory, this paper developed a more generalized large strain radical consolidation model of sand-drained soft foundations under free strain assumption. In this system, the double logarithmic compression permeability relationships for soft soils with large strain properties, the variation of the radical permeability coefficient in the smear zone, and the effect of the non-Darcy flow were all included. Then, the partial differential control equations were numerically solved by the finite difference method and validated with existing radical consolidation test results and derived analytical solutions. Finally, the influences of relevant model parameters on consolidation are discussed. The analysis shows that the greater the maximum dimensionless vacuum negative pressure P0, the faster the consolidation rate of sand-drained foundations. Meanwhile, the decrease in the negative pressure transfer coefficient k1 will result in a decreasing final settlement amount. Moreover, the consolidation rate of sand-drained foundations is slower considering the non-Darcy flow, but the final settlement is unaffected.

Rapid and extensive urbanization has adversely impacted humans and ecological entities in the recent decades through a decrease in surface permeability and the emergence of urban heat islands (UHI). While detailed and continuous assessments of surface permeability and UHI are crucial for urban planning and management of landuse zones, they have mostly involved time consuming and expensive field studies, and single sensor derived large scale aerial and satellite imageries. We demonstrated the advantage of fusing imageries from multiple sensors for landuse and landcover (LULC) change assessments as well as for assessing surface permeability and UHI emergence in Tirunelveli, Tamilnadu, India. Cartosat-2 and Landsat-7 ETM+ imageries from 2007 and 2017 were fused and classified using a Rotation Forest (RF), while surface permeability and temperature were quantified using Soil-Adjusted Vegetation Index (SAVI) and Land Surface Temperature (LST) index, respectively. Fused images exhibited higher classification accuracies than non-fused images, i.e. overall kappa coefficient values 0.83 and 0.75, respectively. We observed an overall increase of 20 km2 (45%) in the coverage of urban (dry, real estate plots and built-up) areas, while a decrease of 27 km2 (37%) for vegetated (cropland and forest) areas in Tirunelveli between 2007 and 2017. The SAVI values indicated an extensive decrease in surface permeability for Tirunelveli overall (0.4) and also for almost all LULC zones. The LST values exhibited an associated overall increase (1.30C) of surface temperature in Tirunelveli with the highest increase (2.40C) for urban built-up areas between 2007 and 2017. The SAVI-LST combined metric depicted the Southeastern built-up areas in Tirunelveli as a potential UHI hotspot, while a caution for the Western riparian zone for UHI emergence in 2017. Our results provide important metrics for surface permeability and UHI monitoring, and inform urban and zonal planning authorities about the advantages of satellite image fusion.

Development of new neurotherapeutics is strongly depending on appropriate animal model chosen in preclinical studies. A cuprizone model is an effective tool for studying demyelination and re-myelination processes in the brain, but BBB integrity in cuprizone model is still a topic for debate. Several publications claim that BBB remains intact during cuprizone-induced demyelination; others demonstrate results that could be explained by the increased BBB permeability. In our work we aim to analyze permeability of BBB for different macromolecules, particularly, antibody-conjugates in cuprizone-intoxicated mice. We compared the traditional approach using Evans blue injection with following dye extraction and detection of antibody-conjugates using magnetic resonance imaging (MRI) and confocal microscopy to analyze BBB permeability in cuprizone model. First, we validated our model of demyelination by detecting changes in gene expression of myelin basic protein and proteolipid protein, and by performing MRI and histological analysis. Our results suggest that the methods with better sensitivity were able to detect the accumulation of macromolecules (such as fluorescent-labeled or gadolinium-labeled antibody conjugates) in the brain, suggesting a local BBB disruption in the demyelinating area. These findings support previous investigations that ques-tioned BBB integrity in cuprizone model and demonstrate possibility for delivery of anti-body-conjugates to demyelinated corpus callosum

Aquaporins (AQPs) are water channels widely distributed in living organisms and involved in many pathophysiologies as well as in cell volume regulations (CVR). In the present study, based on the structural homology existing between mineralocorticoids receptors (MR), glucocorticoids receptors (GR), cholesterol consensus motif (CCM) and the extra-cellular vestibules of AQPs, we investigated the binding of corticosteroids on AQP family through in silico molecular dynamics simulations of AQP2 interactions with cortisol. We propose for the first time a putative AQPs corticosteroids binding site (ACBS) and discussed its conservation through structural alignment. Corticosteroids can mediate non-genomic effects, nonetheless, the transduction pathways involved are still misunderstood. Moreover, a growing body of evidence is pointing out toward the existence of a novel membrane receptor mediating part of these rapid corticosteroids effects. Our results suggest that the naturally produced glucocorticoid cortisol inhibits channel water permeability. Based on these results, we propose a detailed description of a putative underlying molecular mechanism. In this process, we also bring new insights on the regulatory function of AQPs extra-cellular loops and on the role of ions in tuning the water permeability. Altogether, this work brings new insights into corticosteroids non-genomic effects through the proposition of AQPs as membrane receptor of this family of regulatory molecules. This original result is the starting point for future investigations to define more in depth and in vivo the validity of this functional model.

Electromagnetic sensing has been used for diverse applications of non-destructive testing, including the surface inspection, measurement of properties, object characterization. However, the measurement accuracy could be significantly influenced by the lift-off between sensors and samples. To address the issue caused by lift-offs, various strategies have been proposed for the permeability measurement of ferromagnetic steels, which mainly involves different sensor designs and signal features (e.g., the zero-crossing feature). In this paper, a single high-frequency scenario for the permeability retrieval is introduced. By combining the signal of two sensing pairs, the retrieval of magnetic permeability is less affected by the lift-off of sensors. Unlike the previous strategy on reducing the lift-off effect (directly taking the phase term out of the integration) using the Dodd-Deeds analytical method, the proposed method is based on a high-frequency linear feature of the phase term. Therefore, this method has the merit of high accuracy and fast processing for the permeability retrieval (a simplified version of Dodd-Deeds analytical formulas after the integration). Experimental measurement has been carried out on the impedance measurement of designed sensors interrogating ferromagnetic dual-phase steels. For sensor lift-offs of up to 10 mm, the error of the permeability retrieval is controlled within 4 % under the optimal frequency.

The importance of oxygen role during aging process of wine has been long known. Many articles evaluating oxygen inlet for different wine stoppers have been published. However, none of these have studied the impact of the natural cork stoppers production process over oxygen inlet. At the moment, a standardized methodology widely accepted for measuring the oxygen transfer rate (OTR) and/or oxygen permeability of the stopper does not exist. Thus, this article is focused on the aging process (the final phase of the winemaking) and aims to test how some production process of natural cork stoppers impact on the stoppers permeability using chemiluminescence methodology and how also this affects wine ageing. In this study it has been seen that some of its processes such as the application of a surface treatment modify the permeability of the stopper. Surface plays an important role in the corks stoppers production and allows an easier insertion and extraction of the stopper into the bottle, avoiding leaks and homogenizing the stoppers. It was shown that the cork stoppers sample with surface treatment 1 had three times higher oxygen transfer rate than the cork stoppers sample with surface treatment 2 after one year of evolution. The two groups of stoppers had the same in terms of dimensions, density, visual class, batch and manufacture, the only difference between them was the surface treatment used. A red wine was corked with these two types of cork stoppers and its evolution was monitored up to 30 months of ageing. Differences were observed in the evolution of the wines both in certain oenological parameters such as the free SO2, the colour and the evolution of the polyphenols as well as at the sensory level. The wine corked with the stoppers of treatment 1 presented a faster evolution and a higher valuation in the sensory tastes of months 12th, while from the 18th month it presented an over evolution, and the score was below that of the wine with the corks of treatment 2.The data collected in this study shows that the differences observed with the chemiluminescence methodology of cork permeability test at a laboratory level are transferred to wine at the cellar. Therefore, it paves the way to standardize chemiluminescence as a methodology for permeability testing of cork stoppers. This opens a new field for the regulation of the permeability of natural cork stoppers by type of surface treatment applied.

Obstructive sleep apnea (OSA) is a chronic condition characterized by intermittent hypoxia (IH) and sleep fragmentation (SF). In murine models, chronic SF can impair endothelial function and induce cognitive declines. These deficits are likely mediated, at least in part, by alterations in Blood-Brain Barrier (BBB) integrity. Male C57Bl/6J mice were randomly assigned to SF or sleep control (SC) conditions for 4 or 9 weeks, and in a subset 2 or 6 weeks of normal sleep recovery. Presence of inflammation and microglia activation were evaluated. Explicit memory function was assessed with the novel object recognition (NOR) test, while BBB permeability was determined by systemic dextran-4kDA-FITC injection and Claudin 5 expression. SF exposures resulted in decreased NOR performance and in increased inflammatory markers and microglial activation as well as enhanced BBB permeability. Explicit memory and BBB permeability were significantly associated. BBB permeability remained elevated after 2 weeks of sleep recovery (p<0.01) and returned to baseline values only after 6 weeks. Chronic SF exposures mimicking the fragmentation of sleep that characterizes patient with OSA elicits evidence of inflammation in brain regions and explicit memory impairments in mice. Similarly, SF is also associated with increased BBB permeability, the magnitude of which is closely associated with cognitive functional losses. Despite normalization of sleep patterns, BBB functional recovery is a protracted process that merits further investigation.

Metabolic and ionic changes during ischaemia predispose the heart to the damaging effects of reperfusion. Such changes and the resulting injury differ between immature and adult heart. Therefore, cardioprotective strategies for adults need to be tested in immature heart. We have recently shown that simultaneous activation of PKA and EPAC confers marked cardioprotection in adult hearts. The aim of this study is to investigate the efficacy of this intervention in immature hearts and determine whether the mitochondrial permeability transition pore (MPTP) is involved. Isolated perfused Langendorff hearts from both adult and immature rats were exposed to global ischaemia and reperfusion injury (I/R) following control perfusion or perfusion after an equilibra-tion period with activators of PKA and/or EPAC. Functional outcome and reperfusion injury were measured and in parallel, mitochondria were isolated following 5 min reperfusion to determine whether cardioprotective interventions involved changes in MPTP opening behaviour. Perfusion for 5 minutes preceding ischaemia of injury- matched adult and immature hearts with 5 µM 8-Br (8-Br-cAMP-AM), an activator of both PKA and EPAC, led to significant reduction in post-reperfusion CK release and infarct size. Perfusion with this agent also led to a reduction in MPTP opening propensity in both adult and immature hearts. These data show that immature hearts are innately more resistant to I/R injury than adults, and that this is due to a reduced ten-dency to MPTP opening following reperfusion. Further, simultaneous stimulation of PKA & EPAC causes cardioprotection which is additive to the innate resistance.

Under the dual erosion conditions of the dry-wet cycle, which is caused by the high chloride salt concentrations in mine water and fluctuations in mine water level, cemented paste backfill (CPB) suffers serious damage and deterioration. To discuss the mechanical properties and permeability characteristics of CPB under erosion, this study designs an immersion experiment for CPB under chloride salt and dry-wet cycle conditions. Through a uniaxial compressive strength (UCS) test, the change law for the mechanical parameters of the CPB was explored, strength constitutive equation of the CPB was constructed, and the process of deterioration of the CPB was analyzed. Through the penetration test, the diffusion characteristics of packing under chloride salt and dry-wet cycle conditions were explored. The results demonstrated that the strength and elastic modulus of the CPB first increased and then decreased rapidly, with maximum decrease rates of 32.2% and 38.2%, respectively. The CPB structure presents an initial non-damage stage, initial damage stage, damage development stage, damage destruction, and residual damage stage. The chloride ion penetration depth gradually increased with an increase in the number of dry-wet cycles, with a maximum diffusion depth of 20.5 mm. The maximum apparent diffusion coefficient of chloride ion was 18.99×10-10m2/s, and the maximum concentration was 0.303 mol/L. Under the double erosion conditions due to chloride salt and dry-wet cycle, the CPB structure is seriously damaged.

Permeability is an important transport property of porous materials, and its accurate evaluation is relevant in studying applied tasks such as CO2 injection into reservoirs and investigating groundwater quality issues. This study examines the dependence of permeability on total and connected porosity, hydraulic tortuosity, specific surface area, and mean pore radius based on the data of 408 cubic sub-volumes extracted from heterogeneous and naturally fractured cylindrical carbonate samples before and after injection of HCl solutions into them. These parameters were computed using pore-scale modeling of fluid flow. It has been shown that permeability correlates well with porosity and mean pore radius with correlation coefficients of R2≈0.65-0.79 for heterogeneous samples. It was found that the presence of natural fractures significantly influenced the relationship between permeability and other parameters. The relationship between permeability k, tortuosity τ, and specific surface area S is described by power laws k~τ-α and k~S-β, with coefficients α and β substantially exceeding those in the Kozeny-Carman equation. It was also found that there is a parabolic relationship between connected and total porosities both before and after rock dissolution with R2≈0.96-0.99. This allowed for estimation of percolation threshold porosity that are in good agreement with the literature data.

Injuries from exposure to blasts are of significant concern in military operational settings, including tactical training, and is associated with self-reported concussion-like symptomology and physiological changes as increased intestinal permeability (IP) investigated herein. Timeseries gene expression and IP biomarker data were generated from “breachers” exposed to controlled, low-level explosive blast during training. Samples from 30 male participants at pre, post, follow-up blast exposure the next day were assayed via RNA-seq and ELISA. A battery of symptom data was also collected at each of these time points that acutely showed elevated symptom reporting related to headache, concentration, dizziness, and slowed thinking, dissipating ~16hrs following blast exposure. Evidence for bacterial translocation into circulation following blast exposure was detected by significant stepwise increase in microbial diversity (measured via alpha-diversity p=0.049). Alterations in levels of IP protein biomarkers (i.e., Zonulin, LBP, Claudin-3, I-FABP) assessed in a subset of these participants (n=23) further evidenced blast exposure associates with IP. The observed symptom profile was consistent with mTBI and was further associated with changes in bacterial translocation and intestinal permeability, suggesting that IP may be linked to a decrease in cognitive performance. These preliminary findings show for the first

It is widely reported that the mitochondrial membrane potential, ∆Ψm, is reduced in aging animals. It was recently suggested that the lower ∆Ψm in aged animals modulate mitochondrial bioenergetics and that this effect is a major cause of aging since artificially increased ∆Ψm in C. elegans increased lifespan. Here I review, critically, studies that reported reduction of ∆Ψm in aged animals, including worms, and conclude that many of these observations are best interpreted as evidence that the fraction of depolarized mitochondria is increased in aged cells because of the enhanced activation of the mitochondrial Permeability Transition Pore, mPTP. Activation of the voltage-gated mPTP depolarizes the mitochondria, inhibits oxidative phosphorylation, releases large amounts of calcium and mROS, and depletes cellular NAD+, thus accelerating degenerative diseases and aging. Since the inhibition of mPTP was shown to restore ∆Ψm and retard aging, the reported lifespan extension by artificially generated ∆Ψm in C. elegans is best explained by inhibition of the voltage-gated mPTP. Similarly, the reported activation of the mitochondrial Unfolded Protein Response by reduction of ∆Ψm, and the reported preservation of ∆Ψm in dietary restriction treatment in C. elegans are best explained as a resulting from activation or inhibition of the voltage-gated mPTP, respectively.

A self-protective metal/ liquid microcapsule composite plating coating has been prepared in our previous research. The release speed of liquid core material from microcapsules is crucial for the coating surface properties. The aim of this paper is to study the permeability rule of liquid microcapsules within composite coatings. According to permeability experimental data’s linear characteristics, multiple linear regression is firstly used to set up permeability model of liquid microcapsules. The results show that a reliable mathematical model about membrane porosity, viscosity of core material and membrane thickness is established under ambient temperature and moisture. Meanwhile, the predictive capacity and reliability of this model are analyzed carefully.

Objective: To examine associations between IgA responses to Gram-negative gut-commensal bacteria and peri-menstrual symptoms and sex hormone levels during the menstrual cycle in women with and without premenstrual symptoms. Methods: Forty women aged 18-45 years completed the Daily Record of Severity of Problems (DRSP) during all 28 consecutive days of the menstrual cycle. We assayed, in plasma,, IgA responses to 6 Gram-negative bacteria, i.e. Hafnei alvei, Pseudomonas aeruginosa, Morganella morganii, Klebsiella pneumoniae, Pseudomonas putida and Citrobacter pylori, progesterone and oestradiol at days 7, 14, 21 and 28 of the menstrual cycle. Results: Significant changes in Δ (actual minus one week earlier) IgA to LPS of the 6 Gram-negative bacteria during the menstrual cycle were observed with peak IgA levels at T4 (day 28) and lows at T1 or T2 (day 7 or 14). The Δ IgA changes in H. alvei, M. Morganii, P. putida during the menstrual cycle were significantly and positively associated with changes in the total DRSP score, and severity of physio-somatic, anxiety and breast-craving, but not depressive, symptoms. The changes in IgA responses to LPS were largely predicted by changes in progesterone and steady-state levels of progesterone averaged over the luteal phase. Discussion: Menstrual cycle-associated changes in IgA directed against LPS and by inference bacterial translocation may be driven by effects of progesterone on transcellular, paracellular and vascular pathways thereby contributing to the severity of physio-somatic and anxiety symptoms as well as fatigue, breast swelling and food cravings.

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

Coal permeability data are critical in the prevention and control of coal and gas outbursts in mines and are an important reservoir parameter for the development of coalbed methane. The mechanism by which permeability is affected by gas pressure is complex. We used a self-developed true triaxial seepage experimental device that collects lignite and anthracite coal samples, sets fixed axial pressure and confining pressure, and changes gas pressure by changing the orientation of the coal seam to study the influence of the gas pressure on the permeability of the coal seam under the conditions of different coal types and different bedding orientations. Coal permeability decreased rapidly and then decreased slowly and tended to be stable with the increase in gas pressure. This conforms to the power exponential fitting relationship, and the fitting degree reaches more than 99%. The permeabilities of lignite and anthracite were basically the same under various pressure conditions, indicating that the influence of coal type on coal permeability was not significant. The comparison of the two anthracite coal samples showed that the sample's permeability with a bedding plane vertical to the seepage direction was significantly lower than that of the bedding plane parallel to the seepage direction, indicating that gas seeped more easily along the bedding. The sensitivity coefficient of permeability with the change in gas pressure was calculated. The analysis showed that coal permeability was sensitive to changes in gas pressure during the low-pressure stage. When the gas pressure was greater than 0.8 MPa, the sensitivity coefficient was significantly reduced, which may be related to the slow increase in the amount of gas absorbed by the coal seam in the high-pressure stage. A theoretical calculation model of coal seam permeability considering adsorption/desorption and seepage effects was proposed and then verified with experimental results showing that the theoretical model better reflected the permeability characteristics of coal and predicted its permeability. Using the finite element simulation software COMSOL, the extraction efficiency of the coal seam gas under different gas pressure conditions was simulated. The results showed that with an increase in gas pressure, coal permeability and extraction efficiency decreased. In the low-pressure stage, the reduction in the extraction efficiency was more obvious than that in the high-pressure stage.

The paper describes the research findings on dynamic and mechanical properties of composite elastomers with high permeability magnetic filling agent capable of rapidly and reversibly changing its properties when exposed to an external magnetic field, which makes it a perspective material for application in a wide range of engineering areas. The research has analyzed the trends in the strength properties of the materials obtained through the use of filling agents of different fineness, content, and structural organization in the final polymer, under different conditions. This allowed to obtain the correlations between the influence of the filler's relative fineness on the dynamic and mechanical properties of composite polymers, and to estimate the trends in the parameters describing the material strength under the complex magnetic and thermal influence. The results obtained by the authors allowed to ground the composition and structural organization of the final material with the best set of dynamic and mechanical properties.

Rutin, a flavonoid compound found in various plants, has gained attention for its potential applications in the cosmetic industry due to its antioxidant, anti-inflammatory, and potential photoprotective properties. Our review explored the use of rutin (rutoside, 3-O-rutinoside-quercetin) in cosmetics/dermocosmetics, focusing on its physicochemical properties and stability, cutaneous permeability, and efficacy in sunscreen systems, involving in vitro tests and the current state of clinical trials. Rutin's ability to scavenge free radicals, prevent peroxidation, and reduce vascular fragility makes this flavonoid a promising ingredient for photoprotection. Studies have shown that rutin can enhance the sun protection factor (SPF) of sunscreen formulations, especially when combined with organic UV filters. The encapsulation of rutin in nanostructures has also been investigated to improve its applicability. Overall, rutin shows potential as a safe and effective ingredient in cosmetic/dermocosmetic formulations, offering protection against the harmful effects of UV radiation and oxidative stress on the skin.

We report the effect of doping Cd1-xZnxS/ZnS core/shell quantum dot (CSQDs) in nematic liquid crystal p-methoxybenzylidene p-decylaniline (MBDA) at 0.05 wt/wt%, 0.1 wt/wt%, 0.15 wt/wt%, 0.2 wt/wt%, 0.25 wt/wt% and 0.3 wt/wt% concentrations of CSQDs in MBDA. Dielectric parameters with and without bias with respect to frequency has been investigated. The change in electro - optical parameters with temperature has also been demonstrated. The increase in the mean dielectric permittivity has been found due to large dipole moment of CSQDs which impose stronger interactions with the liquid crystal molecules. The dielectric anisotropy changes sign on doping CSQDs in MBDA liquid crystal. It was concluded that the CSQDs doping noticeably increases the dielectric permittivity of nematic MBDA in the presence of electric field. The doping of CSQDs in nematic MBDA liquid crystal reduces the ion screening effect effectively. This phenomenon is attributed to the competition between the generated ionic impurities during assembling process and the ion trapping effect of the CSQDs. The rotational viscosity of nematic liquid crystal decreases with increasing concentration of the CSQDs with faster response time observed for 0.05 wt/wt% concentration. The birefringence of the doped system increases with the inclusion of CSQDs in MBDA. These results find application in the field of display devices, phase shifters, industries and projectors.

This work discusses the feasibility of multiple linear regression in predicting water/CO₂ relative permeability using training and testing datasets from two nearby wells, separately, of the Lower Cretaceous Lakota Sandstone, Jurassic Hulett Sandstone, and Pennsylvanian Minnelusa Formation at the Dry Fork Station site. The outcome is promising as the predicted and measured relative permeability data are decently comparable. Yet, whether this approach could be generally applicable needs more delicate models and larger training datasets to be determined.

We create a model universe by equipping a topological surface (system) with compact dimensions insulated by an information blocking horizon. The insulated compact WF can produce entanglement independent of distance. Interaction between the system and the WF changes the curvature of the first and the quantum state (frequency) of the second in an interconnected relationship. Thus, the field curvature measures the evolution of the particle WF as time. Positive field curvature creates pressure, whereas negative field curvature generates a vacuum, satisfying the Borsuk-Ulam Theorem and the Page and Wootters mechanism of static time. The accumulation of pressure or vacuum generates poles with contrasting dimensionalities, two-dimensional black hole horizons (time infinite), and four-dimensional cosmic voids (time zero). The orthogonality of the field and the compact WF give rise to global self-regulation that fine-tunes the cosmic parameters and can promote fractal topology. The four-dimensional vacuum in cosmic voids can produce an accelerating expansion without dark energy. When gravity effects are eliminated, we find a new, so far unexplored, order-increasing side of entropy. The verifiable and elegant hypothesis satisfies Mach's principle.

Angiostrongylus cantonensis, a zoonotic parasite, can invade the human central nervous system (CNS) and cause acute eosinophilic meningitis or eosinophilic meningoencephalitis. Mice infected with A. cantonensis show elevated levels of pro-inflammatory cytokines, plasminogen activators, and matrix metalloproteinase-9, resulting in disruption of the blood-brain barrier (BBB) and immune cell infiltration into the CNS. Caveolin-1 (Cav-1) regulates the permeability of the BBB, which affects immune cells and cerebrospinal fluid. This intricate interaction ultimately fuels the progression of brain damage and edema. This study aims to investigate the regulatory role of Cav-1 in the pathogenesis of meningoencephalitis induced by A. cantonensis infection. We investigate pathological alterations by triphenyl-tetrazolium chloride, brain water content, BBB permeability, Western blot analysis, and gelatin zymography in BALB/c mice after A. cantonensis. The study evaluates the critical role of Cav-1 regulation through the TLR4 / MyD88 signaling pathway, modulates tight junction proteins, influences BBB permeability, and contributes to brain damage in A. cantonensis-induced meningoencephalitis.

Enhanced oil recovery using nanoparticles is a promising method. However, when injected into a reservoir, nanoparticles can block pores and cause permeability damage. Therefore, enhancing their performance to lower the permeability damage effect is crucial. This study investigated the effect of pH alteration through carbon dioxide (CO2) injection on the permeability damage of limestone caused by the aluminum oxide (α-Al2O3) nanofluid. The methodology involved nanofluid alternating CO2 core flooding experiments by using nanofluids with pH of 4.5 and 2.8. After core flooding, permeability damage was calculated as a percentage of the reduction of the original permeability. The results revealed that the permeability damage in the case of nanofluid alternating CO2 injection was 23.23%. In only nanofluid with a pH of 4.5 injection case, permeability damage was 47.53%. In the 2.8 pH nanofluid injection case, permeability damage was 31.01%. The retention of nanoparticles was confirmed through scanning electron microscopy and energy dispersive X-ray analysis. Permeability damage could be attributed to a large nanoparticles’ agglomeration size, roughness of pore surfaces, and nanoparticle sedimentation. The results of the study revealed that altering pH through the α-Al2O3 nanofluid alternating CO2 injection can effectively reduce the permeability damage of limestone.

A key component of efforts to identify the biological and drug-specific aspects that contribute to therapeutic failure or unexpected exposure-associated toxicity is the study of drug-intestinal barrier interactions. While methods supporting such assessments are widely described for human therapeutics, there is relatively little information available for similar evaluation in support of veterinary pharmaceuticals. There is, therefore, a critical need to develop novel approaches for evaluating drug-gut interactions in veterinary medicine. Three-dimensional (3D) organoids can address these difficulties in a reasonably affordable system that circumvents the need for more invasive in vivo assays in live animals. However, a first step in the development of such systems is understanding organoid interactions in a 2D monolayer. Given the importance of orally administered medications for meeting the therapeutic need of companion animals, we demonstrate growth conditions under which canine colonoid-derived intestinal epithelial cells survive, mature, and differentiate into confluent cell systems with high monolayer integrity. We further examine the applicability of this canine colonoid-derived 2D model to assess the permeability of three structurally diverse, passively absorbed β-blockers (e.g., propranolol, metoprolol, and atenolol). Both absorptive and secretive apparent permeability (Papp) of these drugs at two different pH conditions were evaluated in canine colonoid-derived monolayers and were compared with that of Caco-2 cells. This proof-of-concept study provides promising preliminary results with regard to the utility of canine-derived organoid monolayers for species-specific assessments of therapeutic drug passive permeability.

Engineering of drug nanocarriers combining fine-tuned mucoadhesive/mucopenetrating properties is currently being investigated to ensure more efficient mucosal drug delivery. Aiming to improve the transmucosal delivery of hydrophobic drugs, we designed a novel kind nanogel produced by the self-assembly of amphiphilic chitosan graft copolymers ionotropically crosslinked with sodium tripolyphosphate. In this work, we synthesized for the first time chitosan-g-poly(methyl methacrylate) nanoparticles thiolated by the conjugation of N-acetyl cysteine. First, we confirmed that both non-crosslinked and crosslinked nanoparticles in the 0.05-0.1% w/v concentration range display very good cell compatibility in two cell lines that are relevant to oral delivery, Caco2 cells that mimic the intestinal epithelium and HT29-MTX cells that produce mucin. Then, we evaluated the effect of crosslinking, nanoparticle concentration and thiolation on the permeability in vitro utilizing monolayers of (i) Caco2 and (ii) Caco2:HT29-MTX cells (9:1 cell number ratio). Results confirmed that the ability of the nanoparticles to cross Caco2 monolayer was affected by the crosslinking. In addition, thiolated nanoparticles interact more strongly with mucin, resulting in a decrease of the apparent permeability coefficient (Papp) compared to the pristine nanoparticles. Moreover, for all the nanoparticles, higher concentration resulted in lower Papp suggesting indicating that the transport pathways could undergo saturation.

In the implementation of thermal enhanced oil recovery (TEOR) techniques, the temperature impact on relative permeability in oil - water systems is of special concern. Hence, developing a fast and reliable tool to model the temperature effect on two-phase oil - water relative permeability is still a major challenge for precise studying and evaluation of TEOR processes. To reach the goal of this work, two promising soft-computing algorithms, namely Group Method of Data Handling (GMDH) and Gene Expression Programming (GEP) were employed to develop reliable, accurate, simple and quick to use paradigms to predict the temperature dependency of relative permeability in oil - water systems (K_rw and K_ro). To do so, a large database encompassing wide-ranging temperatures and fluids/rock parameters, including oil and water viscosities, absolute permeability and water saturation, was considered to establish these correlations. Statistical results and graphical analyses disclosed the high degree of accuracy for the proposed correlations in emulating the experimental results. In addition, GEP based correlations were found to be the most consistent with root mean square error (RMSE) values of 0.0284 and 0.0636 for K_rw and K_ro, respectively. Lastly, the comparison of the performances of our correlations against those of the preexisting ones indicated the large superiority of the introduced correlations compared to previously published methods. The findings of this study can help for better understanding and studying the temperature dependency of oil - water relative permeability in thermal enhanced oil recovery processes.

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. Without changing the oil displacement capability of high molecular weight ASP solution in high permeability oil layers, the ASP solution is actively sheared in low permeability oil layers by using a partial quality tool to increase the injection capability of the solution and improve the overall oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, firstly, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.