In this research, Cellulose Nanofibers (NFC) modified with a eutectic of lauric acid (LA) was prepared as a new form-stable phase change material (NFC-LA). Thermal properties of this composite were investigated by Differential Scanning Calorimetry (DSC). The results revealed that the melting temperature and latent heat of NFC/LA were 21.56 °C and 88.5 J/g, respectively; and the super cooling degree for the NFC-LA composite decreased to 13.99 °C when compared to 20.28 °C of the pure lauric acid. Natural clay was purified and modified with Cetyltrimethyl ammonium bromide (CTAB) to prepare organoclay. Through FTIR spectra, we have confirmed that the clay was successfully modified. The PCM-composite was then added to the organoclay to obtain a new composite denoted NFC-LA-OC. this latter was added to cement and was investigated as a reinforcement material in cement mortars for thermal energy storage application. The prepared material can both solve the leakage problem associated to the phase change material, and reduce or even avoid the use of heating and air conditioning systems, which are energy-intensive systems, and therefore reduce energy consumption.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

The energy crisis is currently a major topic in scientific and managerial discussions in the building and construction industry. While employing low-cost strategies for reducing energy usage is beneficial for principals and decision-makers, the primary purpose of this study is to recommend the use of phase change materials (PCM) to improve cooling and heating load management in buildings. In order to accomplish this, the study applies design-builder simulations to a developing country case study. The results indicate that integrating PCM in buildings can reduce energy usage by around 6 percent. Although this value may be lower than other techniques, it is nevertheless important for reaching green building goals in both developed and developing nations. The case study, which takes place in a four-season region, demonstrates the significant potential of the PCM system for both cooling and heating energy management. In addition, the reciprocal performance improvement of PCMs is a remarkable characteristic, especially when contrasted to some conventional systems that focus on a single energy management objective in buildings. Lastly, it should be underlined that the suggested platform is consistent with Sustainable Development Goal 7 (Affordable and Clean Energy Targets).

Plastic contamination of small dimensions (

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

Batch combustion in wood log stoves is a promising application for latent heat storage (LHS), due to the transient heat production with high peak effects. The current study aimed at designing a compact, passive and durable LHS system storing a substantial part of the heat release during batch combustion and effectively releasing the stored heat to the room for 6 to 10 hours after the last batch. The LHS system consists of a coaxial cylinder located at the top of the wood stove, replacing part of the regular stovepipe. Internal metallic fins were applied as heat transfer enhancement to homogenize the temperature distribution inside the PCM. The effect of radial fin lengths was numerically investigated through a parametric study using five different fin lengths within the PCM. Using 35-mm fins in the 70-mm PCM layer yielded the best trade-off for the application. This configuration enabled achieving a slow but close to complete melting of the PCM within a realistic combustion duration, while avoiding overheating the PCM above its degradation temperature. Thereafter, the discharge allowed releasing the stored latent heat for 6 hours. The exhaust gas inlet temperature proved to have a strong influence on the PCM thermal performance.

Over the last two decades, a considerable amount of equipment has been acquired (spreaders, seeders, sprayers, among others) to respond to the challenges of Precision Agriculture (PA) concept. Most of this equipment has been purchased at a high cost. However, many of them, despite still being functional and equipped with sensors, actuators, and electronic processing units capable of adjusting to variations in speed, have become obsolete in terms of communication, and incompatible with new monitoring and control systems based on the “Isobus” protocol. This work aims to present a solution for updating the control system (“Ferticontrol”) of a “Vicon RS-EDW” spreader with variable rate application (VRA), making it compatible with the “InCommand” system from “Ag Leader”. The solution includes low-cost “Arduino” and “Raspberry Pi” microcontrollers and open-source software. The development shows that it is possible to implement a solution that is accessible to farmers in general. It also provides a niche business opportunity for young researchers to set up small technology-based enterprises associated with universities and research centers. These partnerships guarantee permanent innovation and represent a decisive step towards modern, technological, competitive, and sustainable agriculture.

Wounds are an increasing global concern, mainly due to a sedentary lifestyle, frequently associated to the occidental way of life. The current prevalence of obesity in western societies, leading to an increase in type II diabetes, and an elderly population, are also a key factor associated to the problem of wounds healing. Therefore, it stands essential to find wound dressing systems allowing reestablishing the skin integrity in the shortest possible time and with the lowest cost, avoiding further damage and promoting patients´ well-being. Wounds can be classified into acute or chronic, depending essentially on the duration of the healing process, which is associated with. It depends on the extent and depth of wound, localization, level of infection and on the patient health status. For each kind of wound and respective healing stage there is a more suitable dressing. The aim of this review was to focus on the possible wound dressing management, aiming the more adequate healing approach for each kind of wound.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

Miniaturization of electronics devices is often limited by the concomitant high heat fluxes (cooling load) and maldistribution of temperature profiles (hot spots). Thermal energy storage (TES) platforms providing supplemental cooling can be a cost-effective solution, that often leverages phase change materials (PCM). Although salt hydrates provide higher storage capacities and power ratings (as compared to that of the organic PCMs), they suffer from reliability issues (e.g., supercooling). ‘Cold Finger Technique (CFT)’ can obviate supercooling by maintaining a small mass fraction of the PCM in solid state for enabling spontaneous nucleation. Optimization of CFT necessitates real-time forecasting of the transient values of the melt-fraction. In this study artificial neural network (ANN) is explored for real-time prediction of the time remaining to reach a target value of melt-fraction based on the prior history of the spatial distribution of the surface temperature transients. Two different approaches were explored for training the ANN model, using: (1) transient PCM-temperature data; or (2) transient surface-temperature data. When deployed in a heat sink that leverages PCM based passive thermal management systems for cooling of electronic chips and packages, this maverick approach (using the second method) affords cheaper costs, better sustainability, higher reliability and resilience.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (>0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

Pseudolysimachion nakaianum (Ohwi) T.Yamaz. is an endemic species that is an important species in the forest ecosystems of South Korea. This study aimed to develop an in vitro propagation system for P. nakaianum, to enhance the availability of this rare and endemic plant for commercial horticulture and restoration efforts. We utilized cotyledon explants from in vitro germinated seeds and two types of explants (petiole and leaf) from in vitro seedlings to assess the impact of five different cytokinins on adventitious shoot organogenesis in P. nakaianum. The half-strength Murashige and Skoog (MS) medium, supplemented with 10 µM thidiazuron (TDZ) for both cotyledon and petiole explants, yielded the highest shoot induction rates (61.1 ± 9.6% and 26.7 ± 8.8%, respectively) and the greatest number of shoots (3 ± 0.6 and 4.4 ± 0.5, respectively). Responses from leaf explants were variable, with none showing in vitro regeneration. Successfully acclimatized P. nakaianum plantlets in a greenhouse demonstrated normal growth. This protocol outlines an effective method for the direct in vitro regeneration from cotyledon and petiole explants of P. nakaianum, providing valuable information for the conservation of this species.

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

Climate simulations in West Africa have been attributed with large uncertainties. Global climate projections are not consistent with changes in observations at the regional or local level of the Niger basin, making management of hydrological projects in the basin uncertain. This study evaluates the potential of using the quantile mapping bias correction to improve the Coupled Model Intercomparison Project (CMIP5) outputs for use in hydrology impact studies. Rainfall and temperature projections from 8 CMIP5 Global Climate Models (GCM) were bias corrected using the quantile mapping approach. Impacts of climate change was evaluated with bias corrected rainfall, temperature and potential evapotranspiration (PET). The IHACRES hydrological model was adapted to the Niger basin and used to simulate impacts of climate change on discharge under present and future conditions. Bias correction significantly improved the accuracy of rainfall and temperature simulations compared to observations. Nash coefficient (NSE) for monthly rainfall comparisons of 8 GCMs to the observed was improved by bias correction from 0.69 to 0.84. The standard deviations among the 8 GCM rainfall data were significantly reduced from 0.13 to 0.03. Increasing rainfall, temperature, PET and river discharge were projected for all GCMs used in this study under the RCP8.5 scenario. These results will help improving projections and contribute to the development of sustainable climate change adaptation strategies.

The extent of access to energy of displaced populations in settlements and camps in Africa is largely 14 unknown. A multitude of contextual factors, such as the location and the characteristics of housing, 15 the legal status, the socio-cultural background, and the availability of humanitarian and public ser- 16 vices impact the living conditions and the needed energy services. Limitations in accessing energy 17 services have direct, multilayered, and far-reaching implications, including impacts on health, nu- 18 trition, education, protection, and livelihood. The objective of this article is to contribute to a more 19 comprehensive overview of the current state of energy access in displacement contexts on the Afri- 20 can continent by identifying and utilizing existing data. After a screening of the vast and various 21 available information, setting up of a database, consolidating the gathered data as well as assessing 22 the quality through a quality assessment method, the currently available information is visualized 23 and discussed. Considerable differences in the access to electricity for displaced persons across the 24 countries are found. For both electricity and clean cooking, the availability for displaced persons 25 ranges from nearly no access at all up to an access rate of 100%. More strikingly, the results also 26 show that besides South Africa and countries in the Maghreb region, the access to both clean cook- 27 ing and electricity for displaced persons is very low. At the same time, the fragmented data availa- 28 bility, the poor data quality, and the questionable expediency of available data allows neither solid 29 theoretical conclusions nor planning of effective practical implementation measures. Novel inter- 30 disciplinary research, conceptual frameworks and indicators are needed for the purpose of compa- 31 rability and consistency. Future research has the potential to more comprehensively capture the 32 current state of access to energy in displacements contexts and in a next step to examine how energy 33 is interwoven in the lives of displaced people to derive a set of more detailed context-sensitive en- 34 ergy indicators. It is essential that the concerned persons, the displaced persons themselves are in- 35 cluded in the research in a meaningful way.

In the past two decades, several floods have affected people and their properties in Burkina Faso, with the unprecedented flooding occurring in Ouagadougou in September 2009. So far, most studies have focused on Ouagadougou and surrounding localities and have paid little attention to other flood-prone regions in Burkina Faso. Specifically, there is a data and knowledge gap about the flood risk in the Haut-Bassins region, which in turn hampers the development of mitigation strategies and risk reduction measures in communities. This study demonstrates how data collected at the household level can be used to understand flood risk and its components at the village level in this data-scarce region. Using an indicator-based method, we analyze both flood risk and flood risk perception at the village level. Moreover, we determine the factors influencing flood risk perception at the household level using an ordered logit model. We find that 12 out of the 14 villages considered, experience high levels of flood risk. The management of runoff from the nearest urban areas and poorly designed civil engineering infrastructures, such as roads, were highlighted by the households as significant factors that increase their vulnerability. Hence, dependencies in space and between urban and rural areas may play a substantial role in modifying risk. The perceived flood risk consistently exceeds the estimated flood risk, with an insignificant positive correlation between both risk indices. Regression results indicate that flood risk perception is mainly influenced by informational and behavioral factors of the households. The findings of this study can provide valuable information to municipal and regional authorities involved in disaster risk management in the study area. Moreover, the method is transferable to other data-scarce regions

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

As novel materials for carbon capture, phase change solvents can separate into two immiscible phases during the CO2 capturing procedure under a certain temperature. The solvent systems can significantly decrease the energy consumption since the solvents can be regenerated by only heating the rich-CO2 phase. In this work, amino acid ionic liquids (AAILs) were synthesized using quaternary ammonium salts and amino acids as raw materials, and the aqueous solutions were prepared as novel liquid-solid phase change solvents. The results showed that the solvents had excellent CO2 absorption capacity, and the AAILs functionalized by glycine and tryptophan exhibited significant phase change properties. The mechanism of phase-change of the solvent were mainly due to the lower solubility of the product after reaction between AAILs and CO2. The solvent with tryptophan as anion could be regenerated by only heating the CO2-riched solid phase, which might significantly decrease energy consumption of regeneration. And the absorbent could be reused with the regenerated absorption ratio up to 79%. The solvent system has great potential in industrial application due to the easy operation process and efficient recycling ability.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

This article focuses on the issue of motor oils used in the engines of off-road mobile machinery (NRMM), more specifically tractors. The primary goal of the paper is to determine the appropriate replacement interval for these oils. The physical properties of the examined samples were first determined by conventional instruments. Furthermore, the concentration of abrasive metals, contaminants, and additive elements were measured using an optical emission spectrometer. Lastly, the content of water, fuel, glycol, and the products of oxidation, nitration, and sulphation were determined by using infrared spectrometry. The measured values were compared to the limit values. Based on the processing and evaluation of these analyses, the overall condition of the oils was assessed and subsequently the optimal exchange interval of the examined oils was determined. In addition, a risk analysis of the outage was performed. Due to the high yields of crops, farmers can lose a significant amount of product when a tractor is not functioning during the harvest period. This loss for calculated in the paper.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

In contrast to animals, adult organs in plants are not determined during embryogenesis but gen-erated from meristematic cells as plants advance through development. Plant development in-volves a succession of different phenotypic stages and the transition between these stages is termed phase transition. Phase transitions need to be tightly regulated and coordinated to ensure they occur under optimal seasonal, environmental conditions. Polycarpic perennials transition through vegetative stages and the mature, reproductive stage many times during their lifecycles and, in both perennial and annual species, environmental factors and culturing methods can re-verse the otherwise unidirectional vector of plant development. Epigenetic factors regulating gene expression in response to internal cues and external (environmental) stimuli influencing the plant’s phenotype and development have been shown to control phase transitions. How develop-mental and environmental cues interact to epigenetically alter gene expression and influence these transitions are not well understood and understanding this interaction is important considering the current climate change scenarios, since epigenetic maladaptation could have catastrophic con-sequences for perennial plants in natural and agricultural ecosystems. Here we review studies focussing on the epigenetic regulators of the vegetative phase change and highlight how these mechanisms might act in exogenously induced plant rejuvenation and regrowth following stress.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

Pandemics, and other risk-related contexts, require dynamic changes in behavior as situations develop. Human behavior is influenced by both explicit (cognitive) and implicit (intuitive) factors. In this study, we used psychological distance as a lens to understand what influences our decision-making with regards to risk in the context of COVID-19. The study was based on the rationale that our relational needs are more concrete to us than the risk of the virus. First, we explored the impact of social-psychological distance on participants’ risk perceptions and behavioral willingness. As hypothesized, we found that close social relationships of agents promoted willingness to engage in risky behavior. In the second phase, we tested an intervention designed to increase the concreteness of information about virus transmission as a mechanism to mitigate the bias of social influence. We found that the concreteness intervention resulted in significantly reduced willingness to engage in risky behavior. As such, communications aimed at changing the behavior of citizens during times of increased risk or danger, should consider conceptually concrete messaging when communicating complex risk, and hence may provide a valuable tool in promoting health-related behavior.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

Biosolids from stabilized sludge presents a high fertilization potential due to its rich content of nutrients and organic matter. Three formulas of organo-mineral fertilizers based on biosolids were manufactured having at least 2 % N, 2 % P2O5, and 2 % K2O and characterized by classical and advanced methods. The content of N and P in the final formula was measured using specific reactants combined with VIS-nearIR spectroscopy. Additionally, all three formulas were characterized by advanced 1H NMR relaxometry, double-quantum and FT-IR spectroscopy. Structural characterization was performed using SEM, EDX and X-ray diffraction. Four dynamical components were identified in the T2-distribution showing that the rigid component is into a percentage larger than 90 %. In order to evaluate the release properties of organo-mineral fertilizers dynamic measurements of electric conductivity and pH were performed, by placing 0.25 g of formulas (V1, V2 and V3) in 200 ml of distillate water. It was found that V3 present the smallest release velocity, but release the largest amount of fertilizers. Two release mechanisms were also observed.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

This work exclusively focuses on the assessment of the thermal performance of a multifunctional facade panel incorporating PCM in foam layers, recurring to a hot box heat flux meter method to determine the thermal transmittance (U-value). The experimental setup is based on the steady-state approach using climatic chambers, assuring a stable thermal environment. Even small fractions of PCM achieved a small reduction in thermal amplitude. Numerical simulations using Ansys Fluent were developed to evaluate the performance of PCM use over a wide range of temperature boundary conditions and operating modes. These numerical models were calibrated and validated using the results of experimental tests, achieving a correlation factor of 0.9674, thus accurately representing a real-world scenario. The decrement factor (f) was used to analyse the data. It was identified that the efficiency of the panel and size of the optimum region increased with the PCM fraction growth. The simulated behaviour was optimum when the input mean temperature is of 20 °C for a room temperature of between 18-20 °C. The results show the significant potential of the multi-layered panel and the thermal regulator effect of the PCM incorporated on indoor space temperature to reach good thermal comfort levels.

Promoting the use of solar energy resources has always faced the challenges of instability and supply-demand mismatch. The key to solving these issues is to efficiently store and utilize solar energy resources using high-performance heat storage devices. This study designed a high-performance shell-and-tube phase change thermal storage device and established a numerical model using ANSYS software to summarize the device's dynamic melting law. To verify the accuracy of the numerical simulation, a performance testing platform for the phase change thermal storage device was built to investigate the impact of factors such as inlet water temperature, inlet water flow rate, type of heat storage, and initial temperature of the device, and to reveal the change law of the device's performance. The results show that the inlet water temperature has the most significant impact on the device's heat storage and release performance. When the device's heat storage or release is used for heating, changing the inlet water flow rate has a weak and limited effect on the device's performance. However, when the device's heat release is used to provide domestic hot water, increasing the makeup water temperature and reducing the inlet water flow rate can significantly improve the device's effective heat release. Furthermore, based on the experimental validation of the model's correctness, this study further simulated and studied the impact of different factors on the device's heat storage process to optimize its structural design and provide technical references for the device's actual operation and installation. The results show that the placement of fins has a negligible effect on the performance of the heat storage device while reducing the fin spacing and increasing the fin thickness can significantly improve the melting efficiency of the phase change material (PCM). Additionally, the heat storage characteristics of the device are significantly better in the vertical installation mode than in the horizontal installation mode. This study provides theoretical guidance and technical references for the design and use of phase change thermal storage devices.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

A characteristic feature of lightweight constructions is their low thermal mass which causes high internal temperature fluctuations that require high heating and cooling demand throughout the year. Phase Change Materials (PCMs) is effective in providing thermal inertia to low thermal mass buildings. The aim of this paper is to analyse the thermal behaviour of two proposed lightweight buildings designed for homeless people and to investigate the potential benefit achievable through the use of different types of PCM in the temperate climatic conditions of Christchurch, New Zealand. For this purpose, over 300 numerical simulations have been conducted using the simulation software DesignBuilder®. The bulk of the simulations were carried out under the assumption that the whole opaque building envelope is equipped with PCM. The results showed significant energy saving and comfort enhancement through the application of PCMs. Thereby, annual energy saving of over 50 % was reached for some of the PCMs considered. Additionally, the effectiveness of single, PCM-equipped structure components was investigated and substantial benefits between 19 and 27 % annual energy saving were achieved. However, occupant behaviour in terms of ventilation habits, occupancy of zones etc. remains one of the biggest challenges in any simulation work due to insufficient data.

Buttonweed (Cotula coronopifolia) is native to South Africa but invasive in wetlands in Europe, North America, and Australasia, where it excludes native plants. Despite being dry-fruited, field studies suggest migratory waterbirds can disperse its seeds via gut passage (endozoochory), aiding its expansion. To explore the potential for endozoochory in different regions and habitats, we collected seeds from six populations in Spain, Sweden, and the UK. Germination was tested under different salinity levels (0, 5, 10, 15 g/L) and simulated gut passage treatments: scarification, acidification, or both. No germination occurred at 15 g/L. Higher salinity reduced and delayed germination, but full gut passage treatment increased germinability and accelerated germination. Scarification or acid treatment alone resulted in intermediate germination patterns. There were significant salinity x population and gut passage x population interactions on germinability. The acceleration effect of gut passage on germination was stronger at 5-10 g/L than at 0 g/L. This study highlights how migratory birds can facilitate the spread of alien plants introduced by humans. Non-classical endozoochory by waterbirds is an understudied mechanism for the long-distance dispersal of dry-fruited alien plants. Further research on C. coronopifolia, including population genetics, is necessary to understand dispersal mechanisms and facilitate management strategies.

The imperative to achieve carbon neutrality has driven significant advancements in the construction sector, particularly in the production and utilization of building materials. This paper explores innovative strategies and practices designed to reduce the carbon footprint of construction materials, with a focus on both the production processes and the application of sustainable materials. Key innovations include the development of low-carbon and carbon-negative materials, the integration of renewable energy sources in production, and the implementation of advanced recycling technologies. Case studies of successful projects demonstrate how these strategies can be applied in real-world scenarios, highlighting both the benefits and challenges encountered. The analysis also delves into the technical and economic aspects of these innovations, addressing the barriers to their widespread adoption and proposing solutions to overcome these challenges. Through a comprehensive examination of current practices and future trends, this paper aims to provide a roadmap for the construction industry to achieve carbon neutrality, contributing to broader climate change mitigation efforts and fostering a more sustainable built environment.

In order to the effect of hydrated phase change materials on suppressing coal spontaneous combustion, the thermogravimetric experiment and reaction activation energy analysis experiment were used to explore the changes of combustion characteristic, parameters characteristic temperature and activating energy of gas coal, long flame coal, meagre coal, and lean coal before and after adding hydrated phase change materials. The research results showed that hydrated phase change materials increased the coal samples’characteristic temperature point and have effective inhibitory effects on different stages of oxidation process.However, the effect was best at low temperatures, as hydrated phase change materials undergo phase change and absorb heat when heated at low temperatures, isolating coal from contact with oxygen. The activating energy increased by 1.138 KJmol-1～23.048 KJmol-1 and the mass loss reduced by 1.6%～9.3% after the inhibition of the coal sample,indicating that the oxidation rate of various coal samples can be slowed down and the spontaneous combustion can be suppressed by using hydrated phase change materials.At the same time, this material can also reduce the combustibility index of meagre coal and lean coal, as well as the comprehensive combustion index and maximum loss rate of long flame coal and gas coal.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

The purpose of this study was to evaluate the bioactivity and cell response of a well-characterized Nurse´s A-phase (7CaO•P2O5•2SiO2) ceramic and his effect compared to a control (tissue culture polystyrene-TCPS) on the adhesion, viability, proliferation and osteogenic differentiation of ahMSCs in vitro. Cell proliferation (Alamar Blue Assay), Alizarin Red-S (AR-s) staining, alkaline phosphatase (ALP) activity, osteocalcin (OCN) and collagen I (Col I) were evaluated. Also, field emission scanning electron microscopy (FESEM) images were acquired in order to visualise the cells and the topography of the material. The proliferation of cells growing in a direct contact with the material was slower at early stages of the study because of the new environmental conditions. However, the entire surface was colonized after 28 days of culture in growth medium (GM). Osteoblastic differentiation markers were significantly enhanced in cells growing on Nurse´s A phase ceramic and cultured with osteogenic medium (OM), probably due to the role of silica to stimulate the differentiation of ahMSCs. Moreover, calcium nodules were formed under the influence of ceramic material. Therefore, it is predicted that Nurse´s A-phase ceramic would present high biocompatibility and osteoinductive properties being a good candidate to be used as a biomaterial for bone tissue engineering.

To overcome the two-phase flow instability of traditional boiling heat dissipation technologies, a porous wick was used for liquid-vapor isolation, thus realizing efficient and stable boiling heat dissipation. A pump-assisted capillary phase-change loop with methanol as working medium was established to study the effect of liquid-vapor pressure difference and heating power on its start-up and steady-state characteristics. The results indicated that the evaporator undergoes four heat transfer modes including flooded, partial flooded, thin film evaporation and overheating. The thin film evaporation mode was the most efficient one with the shortest start-up period. Besides, the heat transfer modes were determined by liquid-vapor pressure difference and power. The heat transfer coefficient could be significantly improved and the thermal resistance could be reduced by increasing liquid-vapor pressure difference as long as it did not exceed 8 kPa. However, when the liquid-vapor pressure difference exceeded 8kPa, its influence on the heat transfer coefficient weakened. In addition, a two-dimensional heat transfer mode distribution diagram considering both liquid-vapor pressure difference and power was drawn through a great number of experiments. During engineering application, the liquid-vapor pressure difference can be controlled to maintain efficient thin film evaporation in order to achieve the optimum heat dissipation effect.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

The agronomic characteristics of Cenchrus purpureus were assessed through a randomized block experimental design with seven accessions (Taiwan grass, King grass, Elephant grass, Merkeron, CT-115, Purpule grass and Maralfalfa) as treatments and four replications research was carried out at the Instituto Tecnológico Superior de Tantoyuca, in 2019 and 2020, under rainfed conditions. Sowing density was established at 36 tillers in 25 m2. Green and dry matter yield, daily rates of dry matter accumulation in leaves, leaf/stem ratio, height, leaf area index and cutting frequency were assessed. Rainfall amount, temperature, relative humidity and global radiation levels were recorded to assess their effect on the evaluated variables. One-way ANOVA and multivariate analysis techniques, such as multiple linear regression (MLR), Clustering, and Principal component analysis (PCA) with the Statistica V7 software, were used. The leaf area index was greatest (p < 0.05) on the dry season. Green and dry matter yield were greatest in Maralfalfa (p < 0.05). Variation in the results is attributed to weather phenomena; nonetheless, Elephant grass and Maralfalfa showed the highest yields. Quality parameters must be evaluated to identify those grasses with the best attributes.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Lamb waves occur in thin-walled structures in two wave modes, the symmetric and antisymmetric mode. Their oscillation on the structures‘ surfaces is either in phase (symmetric) or shifted by a phase angle of π (antisymmetric). In this work, a method is developed to compare the surfaces‘ oscillation phase relation. It is based on the evaluation of time signals regarding the instantaneous phase angle using the continuous wavelet transformation and as a comparative method the short-time Fourier transformation. For this purpose, numerical simulations utilizing the finite element method provide time signals from the top and bottom surface of different thin-walled structures. They differ with respect to their material settings and laminate configurations. The numerically obtained time signals are evaluated by the developed methods. The occurring oscillation phase differences on the top and bottom surface are studied and both methods are compared. Subsequently, the oscillation phase is evaluated experimentally for the wave propagation in a fiber metal laminate. It is shown that the method based on the continuous wavelet transformation is suitable for the evaluation of oscillation phase relations in time signals. Additionally, it is proven that fiber metal laminates show only two phase relations which indicates the occurrence of Lamb waves.

This study presents PlanteSaine, a novel mobile application powered by Artificial Intelligence (AI) models explicitly designed for maize, tomato, and onion farmers in Burkina Faso. Agriculture in Burkina Faso, like many developing nations, faces substantial challenges from plant pests and diseases, posing threats to both food security and economic stability. PlanteSaine addresses these challenges by offering a comprehensive solution that provides farmers with real-time identification of pests and diseases. Farmers capture images of affected plants with their smartphones, and PlanteSaine's AI system analyzes these images to provide accurate diagnoses. The application's offline functionality ensures accessibility even in remote areas with limited internet connectivity, while its messaging feature facilitates communication with agricultural authorities for guidance and support. Additionally, PlanteSaine includes an emergency alert mechanism to notify farmers about pest and disease outbreaks, enhancing their preparedness to deal with these threats. An AI-driven framework, featuring an image feature extraction phase with EfficientNetB3 and an artificial neural network (ANN) classifier, was developed and integrated into PlanteSaine. The evaluation of PlanteSaine demonstrates its superior performance compared to baseline models, showcasing its effectiveness in accurately detecting diseases and pests across maize, tomato, and onion crops. Overall, this study highlights the potential of PlanteSaine to revolutionize agricultural technology in Burkina Faso and beyond. Leveraging AI and mobile computing, PlanteSaine provides farmers with accessible and reliable pest and disease management tools, ultimately contributing to sustainable farming practices and enhancing food security. The success of PlanteSaine underscores the importance of interdisciplinary approaches in addressing pressing challenges in global agriculture

The definition of UTC in 1972 balanced the needs of the time and frequency community for a universal time scale that was traceable to the definition of frequency in the SI system of units with the needs of the astronomical community for a time scale that was closely linked to UT1, a time scale related to the rotation of Earth. The balance between these two considerations has changed very significantly since 1972, and there is widespread agreement that the method of relating UTC to UT1 should be changed by increasing the maximum tolerance between the two scales to more than the current limit of 0.9 s. I propose to realize this decision by means of an algorithmic adjustment process based on the variation in the length of the day over the previous centuries. I use these historical data to extrapolate the length of the day for a century into the future, and to compute a periodic rate adjustment to UTC based on this extrapolation. The adjustment process will not use time steps. The magnitude of the periodic rate adjustment will be re-considered every century, but the basic adjustment algorithm will not change. I suggest a maximum tolerance between UT1 and UTC that is large enough to absorb the irregular and unpredictable variations in the length of the day with respect to the long-term average increase in this value but plays no role in determining the parameters of the adjustment process that is proposed. I also propose that the adjustment be implemented at 12 UTC on 1 January since that is closest to a universal holiday in all time zones.

The study of the tribological behavior of the braking system in auto vehicles requires knowing the characteristics of the material in contact and, in the work process, for the friction pair, brake disc-pads. Materials structural analysis is necessary because the wear process depends on the friction pair chemical composition, and brake disk-pads, respectively on the work process parameters (pressing force, rotational speed, traffic conditions, etc.). The material of the brake discs is generally the same gray cast iron, but the brake pads can be semi-metallic (particles of steel, copper, brass, and graphite, all united with a special resin), organic materials (particles of rubber, glass, and kevlar all joined with the help of a resin), composite materials that contain different constituents and ceramic materials (rarely have small copper particles). Therefore, the purpose of the paper is to know the crystalline structure and the mechanical properties of the brake pad materials, through specific studies and analyses, with important implications on the friction and wear behavior.

This paper, from the perspective of Mode 3 of knowledge production, takes the important carrier of knowledge, scientific research papers, as the research object. The mainstream databases (SCIE and SSCI) are chosen as the data sources. Firstly, bibliometric methods are applied to analyze the cooperation status among the main bodies of paper production, including authors and their affiliated institutions, countries, and disciplines; secondly, the Analytic Hierarchy Process (AHP) is used to construct a comprehensive evaluation model for the state of research cooperation in carbon neutrality. Based on the evaluation model, the cooperation characteristics of different disciplinary fields and the relationship between paper cooperation status and high-impact research papers are comparatively analyzed. At the same time, an analysis is conducted on the support from the government, the sponsorship from enterprises, and the participation of the public in the process of paper production. Finally, some suggestions are put forward on how to build an innovative ecosystem for carbon neutrality research from the perspective of Mode 3 of knowledge production.

The poor solvent crystallization of carbapenem CS-023 has been performed at 25 °C. The following results have been obtained: 1) A solvate crystal Form A (5/2 Ethanol·1/2 H2O) is recovered from 80 v/v% ethanol solution, 2) Form A transforms to Form H (4H2O) by the solid-phase transition through the solvate-free polymorph, Form A-2, and Form A also transformed to Form C (1Ethanol·3H2O) by the solvent-mediated transformation. In the present study, we found that Form C also transforms to Form H by the solid-phase transition through the solvate-free polymorph, Form C-2. The three polymorphs, Form A, H, and C, were composed of the helical-chain structures, respectively. However, there was an incomprehensible affair in the solid phase transition among the three polymorphs. Namely, Form A comprised a left-handed helix.On the other hand, Form C and Form H’s helix chains were in a left- and right-handed helix complex. The solid-phase transition of Form A into Form H suggested the switch of helicity in the solid. We attempted to explain the helicity change in the solid phase transition. As a result, it was suggested that the over-absorption of water of Form A-2 at high humidity plays a vital role in the helicity change.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

A general procedure is described, to generate material parameter sets to simulate fire propagation in horizontal cable tray installations. Cone Calorimeter test data is processed in an inverse modelling approach. Here, parameter sets are generated procedurally and serve as input for simulations conducted with the Fire Dynamics Simulator (FDS). The simulation responses are compared with the experimental data and ranked based on their fitness. The best fitness was found for a test condition of \SI{50}{\kilo\watt\per\meter^2}. Low flux conditions \SI{25}{\kilo\watt\per\meter^2} and less exhibited difficulties to be simulated accurately. As a validation step, the best parameter sets are then utilised to simulate fire propagation within a horizontal cable tray installation and are compared with experimental data. It is important to note, the inverse modelling process is focused on the Cone Calorimeter and not aware of the actual validation step. Despite this handicap, the general features in the fire development can be reproduced, however not exact. The fire in the tray simulation extinguishes earlier and the total energy release is slightly higher as compared to the experiment. The responses of the material parameter sets are briefly compared with a selection of state of the art procedures.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Corresponding to the principles of biological synapses, an essential prerequisite for hardware neural networks using electronics devices is continuous regulation of conductance. We implemented artificial synaptic characteristics in a (GeTe/Sb2Te3)16 iPCM with a superlattice structure under optimized identical pulse trains. Based on atomically controlling the Ge switch in the phase transition that appears in the GeTe/Sb2Te3 superlattice structure, multiple conductance states were implemented by applying the appropriate electrical pulses. Furthermore, we found that the bidirectional switching behavior of a (GeTe/Sb2Te3)16 iPCM can achieve a desired resistance level using the pulse width. Therefore, we also fabricated a Ge2Sb2Te5 PCM and designed a pulse scheme based on the phase transition mechanism to compare to the (GeTe/Sb2Te3)16 iPCM. We designed an identical pulse scheme that implements linear and symmetrical LTP and LTD based on the iPCM mechanism. As a result, the (GeTe/Sb2Te3)16 iPCM showed relatively excellent synaptic characteristics by implementing gradual conductance modulation, a nonlinearity value of 0.32, and LTP/LTD 40 conductance states using identical pulses trains. Our results demonstrate the general applicability of the artificial synaptic device for potential use in neuro-inspired computing and next generation non-volatile memory.

In the present work freezing and melting characteristics of water seeded with chemically functionalized graphene nano-platelets in a vertical cylindrical capsule was experimentally studied. The volume percentage of functionalized graphene nano-platelets was varied from 0.1% to 0.5% with an interval of 0.1%. The stability of the synthesised samples were carried out by zeta potential distribution. The thermal conductivity of the nanocomposite samples were experimentally measured using transient hot wire method. A maximum enhancement of ~24% in the thermal conductivity was observed for the 0.5% volume percentage in the liquid state while a ~53% enhancement in the solid state. Freezing and melting behaviour of water dispersed with graphene nanoplatelets were carried out using a cylindrical stainless steel capsule in a constant temperature bath. The bath temperatures considered for studying freezing characteristics were considered to be −6 °C and −10 °C, while to study the melting characteristics the bath temperature was set as 31 °C and 36 °C. The freezing and melting time decreased for all the test conditions when the volume percentage of GnP increased. The freezing rate was enhanced by ~ 43% and ~32% for the bath temperatures of −6 °C and −10 °C respectively at 0.5 vol % of graphene loading. The melting rate was enhanced by ~42% and ~63% for the bath temperature of 31 °C and 36 °C respectively at 0.5 vol % of graphene loading.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

Kamchatka berries (Lonicera caerulea L.) are known for their high content of phenolic compounds or vitamins, which is reflected in their antibacterial, detoxifying and anti-inflammatory properties. They are used in the production of jams, juices, wines and as natural dye. A bioferment was prepared from the pomace of the Kamchatka berry varieties Aurora and Indigo Gem and the strains Saccharomyces cerevisiae and Lacticaseibacillus paracasei, which was used to prepare a cosmetic preparation with a concentration of 5% in accordance with the guidelines of the COSMOS certification body. Conducted physico-chemical and organoleptic analyses and bioactive profile characterisation (UHPLC-DAD and UHPLC-ESI-MS/MS). The results showed that the presence of caffeic acid 4.47 ± 0.07 mg/100g was detected after fermentation of Kamchatka berry pomace. Vitamin C content increased by 141% after fermentation of Kamchatka berry pomace. The results of stability tests showed that in the process of physicochemical analysis of cosmetic preparation with bioferment of Kamchatka berry pomace the pH should oscillate in the range of 4.38-4.76 ± 0.01. Stability tests showed that the cosmetic should be protected from high temperatures and UV radiation and proved that the product is stable under changing conditions, resulting in lower transport and storage costs.

Iron is an essential nutrient for humans and microbes, such as bacteria. Iron deficiency occurs commonly in critically ill patients, but iron replacement therapy is not considered during the acute phase of critical illness, since it increases iron availability for invading microbes and oxidative stress. However, persistent iron deficiency in the recovery phase is harmful with potential adverse outcomes such as cognitive dysfunction, fatigue and cardiopulmonary dysfunction. Therefore, it is important to treat iron deficiency timely and efficiently. This article reviews current knowledge about iron-related biomarkers in critically ill patients and provides possible criteria to guide decision-making for iron supplementation in the recovery phase of critical illness.

This bibliographic study addresses key aspects related to fishing, product safety, and climate change in the Adriatic Sea region. The examination of product safety focuses on the assessment of contaminants originating from human activities such as industry, mining, agriculture, and household waste disposal. The contamination of the aquatic environment has emerged as a pressing global concern, extending to the Adriatic subbasin. Aquatic organisms, including fish, are prone to accumulating pollutants directly from polluted water sources and indirectly through the food web. The bio-accumulation of potentially hazardous substances, particularly heavy metals, pesticides, PCBs, PAHs, and antibiotic resistance in aquatic organisms, poses a significant threat to human health. Climate change effects will deplete our seafood supply in terms of quantity and safety owing to negative consequences such as higher levels of pollution, parasites, viruses, infections, acidification, and toxicities such as shellfish poisoning. Global food safety strategies should be developed to reduce greenhouse gas emissions and promote environmentally friendly technology, which indirectly affects seafood quality and microbiological safety, especially for Adriatic Sea, which is part of the Mediterranean Sea, characterized by the most polluted waters in the world.

Microplastics (MPs) are a critical environmental issue, with impacts ranging from ecosystem contamination to health risks through bioaccumulation. This review addresses the inefficacy of traditional water treatments in removing MPs and proposes photodegradation, particularly via nanomaterial-enhanced photocatalysts, as a solution. Utilizing their unique properties like large surface area and tunable bandgap, nanomaterials significantly improve degradation efficiency. Different strategies for photocatalysts modification to improve photocatalytic performance are thoroughly summarized, with the particular emphasis on element doping and heterojunction construction. Furthermore, this review thoroughly summarizes the possible fundamental mechanisms driving photodegradation of microplastics facilitated by nanomaterials, with a focus on processes like free radical formation and singlet oxygen oxidation. By clearly elucidating these strategies and mechanisms, this review aims to provide valuable insights and inspire further progress in microplastic photodegradation.

The solar water heater must be integrated into future residential buildings as the main energy source, which will subsequently reduce the energy cost of water heating. An original configuration for efficient Domestic Hot Water "DHW" storage tank is developed and experimentally evaluated under Saharan climate. This novel DHW configuration includes a hybrid (solar and electric) energy system with a flat plate solar collector coupled with an electric heater. Additionally, phase change material "PCM" mixture that is composed of paraffin wax and animal fat with a melting temperature between 35.58°C and 62.58°C and latent heat between 180 and 210 kJ/kg is integrated into this novel tank configuration. The experimental results indicated that hot water production by using latent heat storage could be economically attractive. In this proposed configuration, one liter of hot water may cost around 0.1362 DZD/liter (i.e., 0.00096 US$/liter) compared to 0.4431 DZD/liter for the conventional water heater, an average energy cost savings of 69.26%. On a yearly basis, the average energy cost savings may reach up to 80.25% if optimal tilt for the solar collector is adopted on a monthly basis. The flat plate collector may be vulnerable to convective heat transfer, and therefore, other solar collectors such as vacuum tube collectors may provide enhanced energy performance.

Museums are called to respond to contemporary challenges and contribute to the formation of more progressive societies. One of the major challenges of our time is climate change and museums could construct cocreated narratives around climate and implement targeted actions for the audiences through their sensorial and affective experiences. More specifically, Geology and Palaeontology museums are repositories of knowledge on geoheritage and geoconservation, recognized for their scientific, pedagogical, cultural and recreational values. The educational potential of geological and paleontological exhibits could be used in informal education activities regarding the climate emergency. Taking the above into consideration, this study focuses on both the creation and evaluation of an educational program for the Natural History Museum of Arsakeio Campus at Psychicko.

Subnational governments play a key role responding to climate change risks in terms of policy strategies and instruments. This article analyzes how Brazilian municipal and state governments have developed and implemented public policies to mitigate and to adapt to climate change risks. We surveyed all cities’ and states’ climate policies within the country. The methodological approach includes five main points of analysis: 1. mitigation targets and intentions; 2. adaptation actions; 3. stakeholders’ participation; 4. policy implementation; 5. participation in networks related to climate change. Our results suggest that even though subnational climate policies in Brazil are isolated initiatives within the national context, they play an important role responding to climate change risks in different scales and levels. The strongest Brazilian policies with both mitigation and adaptation actions counted on previous mobilization for the climate issue involving different stakeholders from several segments of the society. These governments have also participated in transnational cooperation networks related to climate change.

Introduction: Subtalar Arthroereisis (STA) is a surgical intervention for pediatric flexible flatfoot (PFF), primarily targeting hindfoot alignment by limiting excessive subtalar eversion. However, its effects on forefoot parameters remain underexplored. This study aims to investigate radiological changes following STA in pediatric patients. Materials and Methods: A retrospective analysis was conducted on consecutive patients treated with STA for PFF. First ray-related angles, including Hallux Valgus Angle (HVA) and Inter-Metatarsal Angle (IMA), alongside hindfoot radiological parameters such as Meary, Calcaneal Pitch, and Costa Bartani angles, were assessed. Subgroup analysis by gender was performed, and correlations between demographic and pre-operative radiological parameters were examined. Results: Forty-one patients (81 feet) with a mean age of 11.6 years were included, with a mean follow-up duration of 6.4 months. No significant differences were observed in first ray-related an-gles pre- and post-operatively, with mean IMA changing from 7.97° to 7.18° and mean HV angles from 9.51° to 8.66°. Noteworthy improvements were seen in flat foot angles, including Meary, Calcaneal Pitch, and Costa Bartani angles, postoperatively. Age subgroup analysis revealed similar trends in IMA and HVA changes between Group A (operated before peak growth) and Group B (operated later). Higher preoperative angles tended to improve, while lower preoperative IMA and HVA tended to worsen postoperatively, all remaining within normal ranges. Conclusion: STA showed positive radiological outcomes for PFF treatment, while negligible changes in first ray-related angles were observed. Age subgroup analysis indicated similar trends regardless of operation timing. Higher preoperative angles tended to improve, while lower preoperative angles tended to worsen postoperatively, despite all falling within non-pathological ranges. Further re-search is warranted to confirm this correlation.

The enterprise software sector is experiencing a significant transformation driven by rapid technological progress and evolving business needs. An effective release management process is crucial for the solution providers and customers, as they incorporate the principles of Industry 4.0 and 5.0. With the growing dependence on software solutions and services, ensuring their quality, reliability, and security is highly necessary. The release management process incorporates strategic planning, regression testing, accurate deployment, and continuous monitoring of software updates. However, the rapid advancements in artificial intelligence (AI) and machine learning (ML) create a unique challenge to the release management process. The existing research needs to address the necessary adaptations for Industry 5.0, mainly in product-based software organizations, to the release management process without a change management system. After working with several software solution stakeholders, based on the responses from SaaS project stakeholders, we have presented a revised software release readiness workflow by incorporating a change management module. The preliminary result based on data over a limited period of time indicates that the revised workflow has the potential to improve the management of slippage, particularly by more effectively addressing NFR-related issues, thereby resulting in more predictable and reliable release cycles.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

The study presents an overview of how phase change materials (PCMs) can enhance the freeze-thaw resistance of concrete pavement and mitigate urban heat island (UHI) effects. It discusses various types of PCMs and methods for incorporating them into concrete pavement, along with the mechanical properties of concrete pavement and its compressive strength when using different PCMs. Also, a Python script was used to simulate the effect of PCMs on the surface temperature of concrete pavement in different cold regions. Previous research suggests that porous aggregates, microencapsulation, and pipelines containing liquid PCM are the most common methods for incorporating PCMs into concrete pavement. The researchers reported that using PCMs in concrete pavement results in beneficial thermal properties, indicating that PCM concrete pavement has the potential for anti-freezing and UHI applications. Additionally, this study's simulation results suggest that local climate conditions should guide the selection of PCM materials.

With a growing number of PCMs and new, suitable PCM candidates, an overview is not only important, but also increasingly complex. Classification of PCM was thus changed significantly in the past decades. A review of classification of PCMs from recent years shows that not only different classification criteria are used, but more important that they are often mixed, used inconsistently, even without a clear goal. Focusing on the main goal of current classification schemes, to give an overview of the material options for the search for new, suitable PCM candidates, including already established PCMs, a consistent classification is developed in a desktop study. For this, first, the general options for classification criteria are reviewed, and then the appropriate ones selected. Then, based on them a new, revised PCM classification is suggested. It is specifically detailed with regard to mixtures; for binary mixtures it is based on a literature review performed within the study. The result also stresses the importance of specific R&D: for pure substances the sources and the chemical modification, and for mixtures their optimization by new compositions, additives, etc.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

During the last decade, Bangladesh has been experienced a significant climatic anomalies which lead to an increase in magnitude and frequency of various climate relate extreme events. Climate scientists substantiate that global temperature and precipitation pattern is expected to change, which may result in consequential impact on agriculture, livelihood, and ecosystem. Bangladesh is therefore likely to face substantial challenges in the coming decades. In order to adequately understand this complex, dynamic phenomena, Analyzing historical Climate change scenarios as well as projecting its future trends is a great concern for researcher. This study aims to analyzes/ historical climatic data from (1901-2020), and predict future temperature and precipitation patterns in Bangladesh using CMIP6 data. Data used in this study (Observed data is from CRU TS 4.05 and future data is from CMIP6) have been acquired from WorldClim v2.1. Various methods including correlation, regression, standard deviation, correlation matrix, percentiles, cell statistics, and IDW interpolation were performed to analyze the trends, variability and spatial patterns of temperature and rainfall. This study revealed that Over the historical study period (1901-2020) Bangladesh has been experienced a significant warming trend with an average increase in temperature 2°C and with annual decline of the total precipitation 607.26 mm along with a shift towards drier conditions despite weak correlation with hotter years. Projected climate models represents that Bangladesh minimum temperature is expected to increase from 1°C to 4.4°C as well as maximum temperatures from 1°C to 4.1°C by 2100. Moreover, projected precipitation is expected to increase by 480.38 mm, with the biggest rises during monsoon months. Regional variations in temperature and precipitation are again expected, with the Southeast (SE) likely experiencing the most significant warming and the Northeast (NE) seeing the most substantial increase in precipitation.

Climate change has altered the frequency and severity of extreme weather, which can affect vegetation condition and habitat quality for wildlife. Declines in vegetation productivity during droughts and heatwaves can negatively impact animals that depend on vegetation for water and nutrition. The ability to detect such effects on habitat suitability can reveal refugia, which can be prioritised for protection to improve threatened species conservation. We used the normalised difference vegetation index (NDVI) to look at relationships between vegetation productivity and the presence of koalas (Phascolarctos cinereus) in potential habitat throughout much of their range. Using a large, long-term koala presence dataset, we tested the hypothesis that locations where koalas had been observed would exhibit higher NDVI values than a random, representative sample from the same vegetation group (i.e. woodlands, open forests or tall open forests). We also identified the minimum NDVI threshold at which koalas occurred across time for each vegetation group and compared these to the minimum NDVI values observed across potential koala habitat before and during the millennium drought; one of the worst recorded in Australia. Additionally, we investigated whether vegetation above the minimum NDVI thresholds was significantly closer to perennial water than unsuitable vegetation. We found that koalas tend to occur at locations exhibiting higher NDVI than average for all vegetation groups. We also found that 49% of all vegetation groups maintained a minimum NDVI above the koalas’ NDVI threshold before drought, equating to 190,227 km2, which declined to 166,746 km2 during drought (a 12% reduction). We also found that unsuitable vegetation tended to occur farther from perennial water than suitable vegetation for some vegetation groups. Areas that remained above the NDVI thresholds during the drought should be considered potential refugia for populations during an event of similar magnitude and could indicate future core habitat extent.

Currently, one of the main challenges is the mitigation of the effects of climate change on the agricultural sector. Conventional agriculture, with the intensive use of herbicides and pesticides to control weeds and pests, and the improper use of mineral fertilizers, contributes to climate change by causing increased greenhouse gases and groundwater pollution. Therefore, more innovative technologies must be used to overcome these problems. One possible solution is nanotechnology, which has the potential to revolutionize the conventional agricultural system. Active nanoparticles can be used both as a direct source of micronutrients and as a delivery platform for bioactive agrochemicals to improve crop growth, yield and quality. The use of nanoparticle formulations, including nanopesticides, nanoherbicides, nano-fertilizers and nano-emulsions, has been extensively studied to improve crop health and shelf life of agricultural products. Comprehensive knowledge of the interactions between plants and nanoparticles opens up new opportunities to improve cropping practices through the enhancement of properties such as disease resistance, crop yield, and nutrient use. The main objective of this review is to analyze the main effects of climate change on conventional agricultural practices, such as the use of pesticides, herbicides and fertilizers. It also focuses on how the introduction of nanoparticles into conventional practices can improve the efficiency of chemical pest control and crop nutrition. Finally, this review examines in depth the last 10 years (2014-2024) of scientific literature regarding the use of nanoparticles in agriculture to mitigate the effects of climate change.

The study examines projected changes in dry- and wet-spell probabilities in West Africa using a Markov chain approach. Four simulations of regional climate models from the CORDEX-Africa program were used to analyze projected changes in intraseasonal variability. The results show an increase in the probability of having a dry day, a dry day preceding a wet day and a dry day preceding a dry day, and a decrease in the probability of wet days in the Sahel region under anthropogenic forcing scenarios RCP4.5 and RCP8.5. The decrease in wet days is stronger in the far future and under the RCP8.5 scenario (up to -30%). The study also finds that the probability of consecutive dry days (lasting at least 7 days and 10 days) is expected to increase in the Western Sahel, the Central Sahel, and the Sudanian Area under both scenarios, with stronger increases in the RCP8.5 scenario. In contrast, the decrease is expected over the Guinea Coast, with the changes more important under the RCP4.5. These changes in dry- and wet-spell probabilities are important for water management decisions and risk reduction in the energy and agricultural sectors. The study also highlights the need for decision-makers to implement mitigation and adaptation policies to minimize the adverse effects of climate change.

(1) Background: The aim of the work was to characterize the climatic evolution and change based on the Multi Criteria Classification through the dynamics of bioclimatic indices in viticulture across Italy and its regional administrative boundaries, focusing on latitudes and elevations. (2) Methods: The impact of climate change on viticulture in Italy was analysed and spatialized with reference to historical data from 1991 to 2021 and to the Future Scenarios up to 2080 assumed by SSP2-4.5 and SSP5-8.5, taking into account 13 GCMs. (3) Results: The bioclimatic indices have all shown a significant trend in the historical period, with an increase in temperature and a decrease in precipitation, reflecting their effects on the entire Italian territory with respect to HI, up to 44°N for CI and up to 46°N for DI, regardless of altitude. The Future Scenarios highlighted a shift towards the warmer classes of the two temperature-based indices (HI and CI) for both SSPs, especially for altitudes up to 900 m a.s.l.. The DI-based classification based on DI remained relatively stable in Italy over time, although DI values will become increasingly negative in the near future. (4) Conclusions: The climate in Italy is warming, especially in the south and in the coastal regions. By 2080, more areas will be “Very Hot” with “Warm Nights.” Drought will also increase and have a negative impact on viticulture. The importance of higher latitudes and altitudes in mitigating the effects of climate change justifies the continuing trend towards the relocation of vineyards as a medium-term solution and as an alternative to targeted cultivation methods that must be adopted in the short-term to safeguard the suitability of an area to quality viticulture.

This article examines the impact of climate change on the hydrometeorological state of some lakes and reservoirs in the Akmola and North Kazakhstan regions. Time series with values of various climate parameters for the period 1986-2023 are used for the climate analysis; the reliability of the results was assessed using the Fisher criteria. Hydrometric indicators were studied using the ArcGIG program. Using GIS to spatially analyze water climate data, 8-channel satellite images from 1995 to 2023 were used. During the study, it was found that the area of the main lakes has undergone changes.

In plants, phase change from the juvenile stage to maturity is a tightly controlled process at the physiological and genetic level, which is controlled by evolutionary highly conserved microRNAs. These phase changes are more pronounced in woody plant species, but the majority of molecular genetic studies on the regulation of this transition has been done in annual model or crop species. This process is of particular significance for the in vitro propagation of woody plant species, as individuals or tissues that have undergone the transition to vegetative maturity are recalcitrant to propagation. Development of effective methodologies for silver birch vegetative propagation are required to increase the efficiency of breeding programs. Conserved miRNAs that were differentially expressed between juvenile and mature silver birch tissues were identified using high-throughput sequencing of small RNA libraries. These differentially expressed miRNAs could potentially be utilized to develop markers indicating the juvenility or maturity of silver birch explants and in vitro cultures. In addition, the obtained results will provide an insight into the molecular mechanisms regulating vegetative phase change in silver birch and other perennial woody plant species.

Recent research efforts in bone tissue engineering have been primarily directed towards manufacture-viable synthesis of biomaterials that can significantly enhance the biocompatibilities and osteogenic capabilities on the new biomaterials. This paper presents a straightforward, cost-effective, optimized, and well-controlled hydrothermal synthesis of Nb-doped potassium titanate nanofibers in high-purity. Characterization data revealed that the Nb-doping potassium titanate maintained the crystal structure, showing great promise for applications in bone tissue engineering.

This study investigates the impacts of climate change policies on businesses across various sectors, aiming to understand how these regulations affect operational, financial, and strategic aspects of business management. Utilizing a mixed-methods approach, data was collected from 500 businesses through surveys and interviews, encompassing a wide range of industries, sizes, and geographic locations. The findings reveal a complex landscape where 30% of businesses report positive impacts, primarily in the renewable energy and technology sectors, citing increased demand for green products and improvements in energy efficiency. Conversely, 45% of businesses, especially from manufacturing and agriculture, experience negative impacts, including increased operational costs and regulatory compliance challenges. Notwithstanding, a significant majority of businesses are committed to enhancing their sustainability practices, viewing climate change policies as an opportunity for innovation and long-term growth. The study highlights the nuanced effects of climate change policies, emphasizing the need for sector-specific support measures to alleviate financial and operational burdens on negatively impacted businesses. Moreover, it points to a broader shift towards sustainability within the business community, suggesting that climate policies, despite their varied impacts, are driving significant changes in business strategies towards environmental stewardship.