In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

Positioning based on wireless signals such as mobile communication networks has become an important means to provide high-precision location services in environments where satellite signals are blocked. In complex environments such as indoor and underground, wireless signal propagation is obstructed and non-line-of-sight (NLOS) phenomena appears due to serious occlusion and reflection. The time delay caused by NLOS effects has little impact on communication system but can significantly increase positioning errors in positioning systems. Therefore, effective suppression of NLOS errors is crucial to improving 5G positioning accuracy. To address the insufficient feature extraction of existing NLOS error suppression methods, the neglect of residual NLOS measurement errors, and poor stability of position estimation results, this paper innovatively proposes a NLOS mitigation and location estimation method for 5G positioning terminals. Simulation and experimental test results demonstrate that the proposed method outperforms the comparative methods both theoretically and practically, achieving an average positioning accuracy of 1.85 meters in complex indoor NLOS environments. The method proposed in this paper provides a new strategy for NLOS error suppression in indoor 5G positioning, which can significantly contribute to high-precision location services based on commercial 5G networks.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

A large proportion of chronic stroke survivors still struggle with upper limb (UL) problems in daily activities. We investigated clinical outcomes and assessed the quality of movement before and after a 5-hour error-enhancement training. The pilot study had a pre-post intervention design, recruiting 22 patients in the chronic phase post-stroke with UL motor impairments. Patients received 1-hour robot treatment for five days. Patients were assessed at baseline and after training, collecting (1) clinical (UL Fugl-Meyer assessment (FMA-UE)), action research arm test (ARAT), motor assessment scale UL and tone), (2) patient-reported (hand subscale of the stroke impact scale, motor activity log (MAL), visual analogue scale of pain and tone) and (3) kinematic (KINARM, BKIN Technologies Ltd., Canada) outcome measures. Our analysis revealed significant improvements (median im-provement (Q1-Q3); p<0.05) in (1) FMA-UE (1.0 (0.8–3.0), p<0.001) and ARAT (2 (0.8–2.0), p<0.001); (2) MAL amount of use (0.1 (0.0–0.3), p<0.001) and MAL quality of use (0.1 (0.1–0.5), p<0.001); (3) KINARM-evaluated position sense ((-0.45 (-0.81–0.09), p=0.030) after training. These findings provide insight into kinematic, clinical, and self-reported improvements in UL functioning after five hours of error-enhancement UL training.

In view of the limitations of the existing eccentricity error separation method of the rotary table, an eccentricity error separation method based on the phase feature of the moiré signal of single reading head is proposed herein. A grating pair transmission model is established based on the analysis of the principle of the rotary table, thereby the influence of eccentricity error on the phase feature of the moiré signal in the rotation course of the rotary table is clarified, and the corresponding model between the phase feature spectral components and the eccentricity error is established. The verification experiments of the proposed method are carried out based on the laboratory-made circuit system. After verifying the accuracy of the data acquisition of the laboratory-made circuit board, the verification experiments of the eccentricity error separation effect of the proposed method are carried out. The experimental data are compared with those of the traditional method and the results show that the error between the two methods is 2.34μm and the relative error is 2.3%.

This paper focuses on improving the tracking accuracy for servo systems and increasing the contouring performance of precision machining. The dynamic friction during precision machining is analyzed using the LuGre model. The dynamic and static parameters in the friction model are efficiently and accurately identified using the improved Drosophila Swarm Algorithm based on cross-mutation. The friction tracking error can be deduced by the friction state space and an expression is derived. To compensate for the tracking error caused by friction, a feedforward compensation control is designed to avoid signal lag in traditional friction controllers. Furthermore, the factors of multi-axis parameter mismatching that impact the machining profile accuracy are analyzed for multi-axis control. An adaptive cross-coupled control-based pre-compensation strategy of contour error is designed to reduce both the tracking error and the contour error. The effectiveness of the proposed method is validated through several experiments, which demonstrate a remarkable improvement in tracking performance and contour accuracy.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

We are losing love. By studying porn movies to understand love, I discovered that love originally comes from the body, from positive emotions and vibrations of the wonderful body, from the heart and all other parts of the body, such as sexual organs. António Damásio made Descartes’ error by postulating that feelings increase their power from homeostasis (mechanisms of life regu-lation from bacteria to humans). He made this mistake unconsciously because many people un-consciously have a very bad opinion of sexual organs. We consider them ugly because they come from the prehistoric period. I have combined António and Hanna Damásio’s work (body emotions, thinking and language). I discovered that porn actors do not talk during sex, and this is striking. Porn actors mirror what happens in society. This means that people come from prehistory, do not talk during sex, and still unconsciously behave like primitive animals during sexual intercourse; we do not respect the body sufficiently during sex. Therefore, love, which comes from the body, is smothered and buried. We must very delicately talk to the wonderful, delicious and respectful body to wake up love feelings, body emotions and vibrations during sex. We must invent talking movies with porn films. Language of positive emotions associated with the language of wonderful and delicious body will warm love feelings and will give envy to love through sexual intercourse because António Damásio discovered that emotions are social.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

As one of the fastest-growing new energy sources, wind power technology has attracted widespread attention from all over the world. In order to improve the quality of wind power generation, wind speed prediction is an indispensable task. In this paper, an error correction based Variational Mode Decomposition and Broad Learning System (VMD-BLS) hybrid model is proposed for wind speed prediction. First, the wind speed is decomposed into multiple components by the VMD algorithm, and then an ARMA model is established for each component to find the optimal number of sequence divisions. Second, the BLS model is used to predict each component, and the prediction results are summed to obtain the wind speed forecast value. However, in some traditional methods, there is always time lag, which will reduce the forecast accuracy. To deal with this, a novel error correction technique is developed by utilizing BLS. Through verification experiment with actual data, it proves that the proposed method can reduce the phenomenon of prediction lag, and can achieve higher prediction accuracy than traditional approaches, which shows our method’s effectiveness in practice.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

Using geometric considerations, we provide a clear derivation of the integral representation for the error function, known as the Craig formula. We calculate the corresponding power series expansion and prove the convergence. The same geometric means finally help to systematically derive handy formulas that approximate the inverse error function. Our approach can be used for applications in e.g. high-speed Monte Carlo simulations where this function is used extensively.

Introduction: While preparing for dive exams, divers are trained to perform rescue exercises. Currently, divers think they will manage and control their body at any time.Methods: At the bottom of the water, the student takes the instructor who simulates a sickness, up to the surface, by controlling the going up. Then, if the exercise is wrong, both divers go down and exercise again. If the exercise is successful, both divers go down to perform another exercise until they are tired or until they have no more air. Results: I discovered that there was a mistake in the preparation of divers for rescue training due to Descartes’ error, “I think, thus I am”, which is part of our collective memory. Going up and going down after a sickness simulation is a repetitive action of the body and going down is therefore part of the automatisms of rescue, which is very dangerous. Conclusions: The body is not necessarily controlled by the present thinking, and if divers forget sickness while going up in a real rescue situation, they will go down automatically because their bodies were trained like this. In addition, it is very easy to forget sickness. Divers should not go down after rescue, they should be on the dive boat or on the land. Descartes’ error has to be reversed: “I am, thus I think” is right. The divers’ rescue exercises must be simplified and divers should never go down after the simulation of a sickness.

COVID-19 outbreak started in the Chinese city of Wuhan and spread around the globe in months due to its high contagious level. Hence, this disease posed a great challenge to researchers and mathematicians. Numerous mathematical models have been suggested to visualize the spreading speed and trends of this pandemic. In this paper, a comparison of a widely established and accepted method, the Susceptible-Exposed-Infected-Quarantined-Recovered-Death-Insusceptible (SEIQRDP) model with a newly-proposed fractional-order SEIQRDP is studied. Densely populated Countries of Asia (Pakistan, India, and Bangladesh) have been chosen as data sets and both algorithms have been applied to their data. The same comparison technique has also been used on the data of two polar countries, New Zealand and Russia, that validated our findings. Error comparison of both algorithms has been recorded in a tabulated form which shows multi-fold erroneous trends over WHO data of selected countries.

In this paper, it is proved that s-iteration with error and Picard-Mann iteration with error iterative processes converge strongly to the unique fixed point of Lipschitzian strongly pseudo-contractive map. This convergence is almost -stable and -stable. Applications of these results to the operator equations, where is a strongly accretive and accretive mappings of into itself.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

The main question proposed in this research is if different types of organizational approach, adapted from rapidly changing disciplines — such as IT industry, and software engineering in particular — could help overcome this gap by shortening the response time needed to analyze advanced solutions in accordance with changed circumstances, thus allowing for architectural programming to obtain different positions in the timeline of project planning and realization. We propose a novel methodology of architectural design as a self-reliant instrument inspired by Agile Manifesto and some of its instantiations, most notably by the Scrum Framework.

Wi-Fi fingerprinting positioning systems have been deployed for a long time in location-based services for indoor environments. Combining mobile crowdsensing and Wi-Fi fingerprinting systems could reduce the high cost for collecting the necessary data enabling the deployment of the resulting system for outdoor positioning in areas with dense Wi-Fi coverage. In this paper, we present the results attained in the designing and evaluation of an urban fingerprinting positioning system based on crowdsensed Wi-Fi measurements. We first asses the quality of the collected measurements, highlighting the influence of received signal strength on data collection. We then, evaluate the proposed system by comparing the influence of the crowdsensed fingerprints on the overall positioning accuracy for different scenarios. The evaluation helps gain valuable insight into the design and deployment of urban Wi-Fi positioning systems while also allowing the proposed system to match GPS-like accuracy in similar conditions.

All sensing systems have some inherent error. Often, these errors are systematic, and observations taken within a similar region of space and time can have correlated error structure. However, the data from these systems are frequently assumed to have completely independent and uncorrelated error. This work introduces a correlated error model for GNSS-reflectometry (GNSS-R) using observations from NASA’s Cyclone Global Navigation Satellite System (CYGNSS). We validate our model against near-simultaneous observations between two CYGNSS satellites, and double difference our results with modeled observables to extract the correlated error structure due to the observing system itself. Our results are useful to catalogue for future GNSS-R missions and can be applied to construct an error covariance matrix for weather data assimilation.

In this paper, we shall introduce the interval-valued spatial error model. Based on the idea of least square method of single-valued case, we give the parameter estimator for interval-valued spatial error model. The theoretical properties of the proposed estimator are proved. Finally, we give the numerical analysis and a real example.

Purpose: To compare refractive prediction error (PE)s between phacotrabeculectomy and phacoemulsification. Methods: Refractive PE was defined as the difference of spherical equivalent between the predicted value using the Barrett Universal II formula and the actual value obtained at postoperative one month. Forty-eight eyes that had undergone phacotrabeculectomy (19 eyes, open-angle glaucoma; 29 eyes, angle-closure glaucoma) were matched with 48 eyes that had undergone phacoemulsification by age, average keratometry value and axial length (AL), and their PEs were compared. The factors associated with PE were analyzed by multivariable regression analyses. Results: Phacotrabeculectomy group showed a larger absolute PE compared to the phacoemulsification group (0.51 ± 0.37 Diopters vs. 0.38 ± 0.22, P=0.033). Larger absolute PE was associated with longer AL (P=0.010) and higher intraocular pressure (IOP) difference (P=0.012). Hyperopic shift (PE>0) was associated with shallower preoperative anterior chamber depth (ACD) (P=0.024) and larger IOP difference (P=0.031). In the phacotrabeculectomy group, the PE was inversely correlated with AL: long eyes showed myopic shift and short eyes hyperopic shift (P=0.002). Conclusions: Surgeons should be aware of the possibility of worse refractive outcomes when planning phacotrabeculectomy especially in eyes with high preoperative IOP, shallow ACD, and/or extreme AL.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

A method of accuracy error compensation for the time interval is examined, allowing to eliminate the dependence of accuracy error on the duration of measured intervals and minimising the influence of destabilising factors - ambient temperature changes and the initial deviation of the meter clock generator frequency from the nominal value. The compensation method is based on a calibration procedure that measures precise time intervals under conditions of changing ambient temperature. Then the dependence of the accuracy error on temperature for a particular meter is recorded. Based on these data, a correction table is compiled containing correction factors and temperature values at which these factors were determined. Under real measurement conditions, the correction factor corresponding to the current temperature is determined from the table for measured results correction. The table with correction factor values could be stored in the memory of the meter or processing computer. Experimental verification of the method showed that applying a correction for a meter with a standard XO class clock generator (certificated instability of ±50 ppm) can obtain an equivalent clock generator instability of ±0.15 ppm. The application of the method is efficient in cases where the use of high-end clocking to ensure the required measurement accuracy is not economically feasible.

Real-world time series data sets contain a combination of linear and nonlinear patterns, making the time series forecasting problem more challenging. In this paper, a new hybrid methodology is introduced for forecasting univariate time series data sets using a multiplicative error modeling approach. An autoregressive integrated moving average (ARIMA) model is combined with an autoregressive neural network (ARNN) for improving the predictions of individual forecast models. The proposed multiplicative ARIMA-ARNN model glorifies the chances of capturing the different combinations of linear and nonlinear patterns in time series. The model shows outstanding performance on six standard time-series data sets compared to other widely used single and hybrid forecasting models.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Although migraine belongs to the main causes of disability worldwide the mechanisms of its pathogenesis are poorly known, which is among the reasons that this disease is underdiagnosed and undertreated. As migraine diagnosis is based on the subjective assessment of symptoms, there is a need to establish objective markers of its occurrence and severity. Tryptophan (TRP) metabolism has been associated with the pathogenesis of neurological and psychiatric disorders. In the present work, we investigated an association between migraine and the urine concentration of TRP and its metabolites 5-hydroxyindoleacetic acid (5-HIAA), kynurenine (KYN), kynurenic acid (KYNA) and quinolinic acid (QA) in 21 low-frequency episodic migraine patients and 32 controls. Migraine patients displayed lower urinary levels of 5-HIAA and KYNA, but KYN and QA were enhanced as compared with the controls. Consequently, the patients were characterized by different values of the 5-HIAA/TRP, KYN/TRP, KYNA/KYN, and KYNA/QA ratios. Furthermore, urinary concentration of 5-HIAA was negatively correlated with Migraine Disability Assessment score, monthly migraine, and monthly headache days. A negative correlation between Patient Health Questionnaire 9 scores assessing depression. In conclusion, the urinary 5-HIAA level may be an easy-to-determine marker of migraine occurrence and severity and may contribute to the identification of migraine patients with depression.

The redshifted 21 cm line signal is a powerful probe of the cosmic dawn and the epoch of reionisation. The global spectrum can potentially be detected with a single antenna and spectrometer. However, this measurement requires an extremely accurate calibration of the instrument to facilitate the separation of the 21 cm signal from the much brighter foregrounds and possible variations in the instrument response. Understanding how the measurement errors propagate in a realistic instrument system and affect system calibration is the focus of this work. We simulate a 21 cm global spectrum observation based on the noise wave calibration scheme. We focus on how measurement errors in reflection coefficients affect the noise temperature, and how typical errors impact on the recovery of the 21 cm signal, especially in the frequency domain. Results show that for our example set up, a typical VNA measurement error in the magnitude of the reflection coefficients of the antenna, receiver, open cable which are 0.001, 0.001, 0.002 (linear) respectively would result in a 200 mK deviation on the detected signal, and a typical measurement error of 0.48∘, 0.78∘, 0.15∘ in the respective phases would cause a 40 mK deviation. The VNA measurement error can greatly affect the result of a 21 cm global spectrum experiment using this calibration technique, and such a feature could be mistaken for or be combined with the 21 cm signal.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

Formula feeding, as an alternative to breastfeeding, offers benefits such as convenience and consistent nutrition. Among the drawbacks of formula feeding, however, is potential dilution or concentration errors in the of formula during preparation that may lead to infant health issues. The present study aimed to investigate the accuracy of caregiver measurements as they prepared infant formula under multiple conditions, compared with manufacturer specifications. A diverse sample of caregivers (N = 84) participated in this cross-over experimental study. Participants hand-scooped infant formula powder and poured water to prepare 4oz and 7oz feedings, using both a standardized set of infant formula products and participants’ own products. Linear mixed effects models were used to estimate fixed effects of target amount (4oz versus 7oz) and products (participant versus researcher) on mean absolute percent error (MAPE) of measurement. Across all conditions MAPE was significantly greater for measuring powder than for water (9.0% vs. 4.4%; p&lt;0.001) with a combined powder and water MAPE at 13.0%. Greater measurement error was associated with the odd-sized 7oz preparation and participants’ own products. We observed considerable variability and substantial error during infant formula preparation, particularly for hand-scooping of powder, which tended toward higher values than the theoretical gold standard.

Academic publishing is undergoing a highly transformative process, and many rules and value systems that were in place for years are being challenged in unprecedented forms leading to the evolution of novel ways of dealing with new pressures. One of the most important aspects of an integrated and valid academic literature is the ability to screen publications for errors during peer review to weed out mistakes, fraud and inconsistencies, such that the final published product represents a product that has value, intellectually, and otherwise. It is difficult to claim the existence of perfect manuscripts. The level of errors that exist in a manuscript will depend on the rigor of the research group and of the peer review process that was used to screen that paper. When errors slip into a final published paper, either through honest error or misconduct, and are not detected during peer review and editorial screening, but are spotted during post-publication peer review, an opportunity is created to set the record straight, and to correct it. To date, the most common forms of correcting the literature have been errata, corrigenda, expressions of concern, and retractions. Despite this range of corrective measures, which represent artificially created corrals around pockets of imperfect literature, certain cases do not quite fit this mold, and new suggested measures for correcting the literature have been proposed, including manuscript versioning, amendments, partial retractions and retract and replace. In this commentary, a discussion of the evolving correction of the literature is provided, as are perspectives of the risks and benefits of such new measures to improve it.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

During the hand-eye calibration process of the manipulator, the Euclidean distance error of the calibration results cannot be calculated because the true values of the hand-eye conversion matrix cannot be obtained. In this paper, a new method of projection error analysis is presented. Error analysis is carried out by using a priori knowledge that the location of AR markers is fixed in the calibration process. The coordinates of the AR marker center point are reprojected to the pixel coordinate system, and then compared with the true pixel coordinates of the AR marker center point obtained by corner detection or manual labeling in order to obtain the Euclidean distance between the two coordinates as the basis for error analysis. Experimental results show that the proposed optimization method can greatly improve the accuracy of hand-eye calibration results.

In this paper we compare the effects of forecasting demand using individual (disaggregated) components versus first aggregating the components either fully or into several clusters. Demand streams are assumed to follow autoregressive moving average (ARMA) processes. Using individual demand streams will always lead to a superior forecast compared to any aggregates, however we show that if several aggregated clusters are formed in a structured manner then these subaggregated clusters will lead to a forecast with minimal increase in mean-squared forecast error. We show this result based on theoretical MSFE obtained directly from the models generating the clusters as well as estimated MSFE obtained directly from simulated demand observations. We suggest a pivot-algorithm, that we call Pivot Clustering, to create these clusters. We also provide theoretical results to investigate sub-aggregation, including for special cases such as, aggregating MA(1) streams and ARMA streams with similar or same parameters.

This study proposes self-calibration of capacitor mismatch errors for high-resolution pipeline analog-to-digital converters (ADCs). The proposed calibration circuit recursively amplifies the capacitor mismatch error by re-utilizing a multiplying digital-to-analog converter in a pipeline stage without increasing the circuit complexity, and the amplified error voltage is converted into digital code by utilizing the remaining pipeline stages. Error correction is performed by subtracting the digital code from the ADC output during normal operation. A prototype of a 12-bit pipeline ADC is fabricated in a 0.18 µm standard CMOS process. The ADC comprises eight 1.5-bit stages, followed by a 4-bit flash ADC as the final stage; the capacitor mismatch errors in the first two pipeline stages are corrected by utilizing the proposed self-calibration technique. At a sampling rate of 30 MS/s, the measured differential and integral nonlinearities improve from +0.82/-0.75 and +1.12/-1.79 to +0.45/-0.41 and +0.47/-0.91 after calibration, respectively. Further, the measured dynamic performances improve significantly with calibration. For an input frequency of 2.09 MHz, the ADC achieves a spurious-free dynamic range (SFDR) and signal-to-noise and distortion ratios (SNDR) of 69.3dB and 63.9dB before calibration, respectively. After calibration, the SFDR and SNDR increase to 84.1dB and 68.9dB, respectively, and the effective number of bits is approximately 11.1bit. The power consumption of the ADC is 35mW under 1.8V supply, and the resulting figure of merit is 514fJ/conversion step.

The Kwee van Woerden (KvW) method for the determination of eclipse minimum times has been a staple in eclipsing binary research for decades, due its simplicity and independence of external input parameters. However, its estimates of the timing error have been known to be of low reliability. During the analysis of very precise photometry of CM Draconis eclipses from TESS space mission data, KvW’s original equation for the timing error estimate produced numerical errors, which evidenced a fundamental problem in this equation. This contribution introduces an improved way to calculate the timing error with the KvW method. A code that implements this improved method, together with several further updates over the original method is presented as well. An example application on the CM Draconis light curves from TESS is given, where we show that its timing error estimates of about 1 second are in excellent agreement with error estimates obtained by other means.

Plantar flexors (PF) spasticity is known to poorly correlate with active dorsiflexion (DF) impairment throughout the swing phase of hemiparetic gait. Spastic Cocontraction, instead, stemming from descending pathways, potentially misdirect antagonist PF activity opposing DF during swing. Electromyographic (EMG) recordings, while unable to differentiate between reflex-based and descending origins, may offer valuable insights into this distinction by exploring PF EMG activity after tibial nerve neurotomy (which eliminates PF spasticity). Eleven subjects with hemiparesis walking at comfortable velocity and 11 controls walking at comfortable and slow velocity, underwent kinematic and PF/DF EMG analysis. Five of the hemiparetic subjects underwent tibial neurotomy &gt;1 year prior. We evaluated spasticity at rest (Tardieu scale), maximal ankle dorsiflexion, tibialis anterior agonist recruitment and gastrocnemius medialis and soleus cocontraction coefficients during swing. At slow velocity, controls (0.80±0.12 m/s) moved at a similar pace as hemiparetic subjects (0.73±0.37 m/s, NS). Hemiparetic subjects showed: (i) reduced ankle DF across swing (ii) increased PF cocontraction, including before any DF (iii) higher cocontraction despite absent spasticity in tibial neurotomy subjects (iv) higher tibialis anterior recruitment. Increased PF cocontraction occurs in the absence of spasticity or ankle DF despite higher agonist recruitment. Spastic cocontraction is a major factor limiting active DF at swing, unlike spasticity.

The fractional reduced differential transform method is a finite iterative method based on infinite fractional expansions. The result obtained is the approximation of the real value. There are few reports on the approximate error and the applicable condition. In this paper, according to the fractional expansions, we study the factors related to the approximate errors. Our research shows that the approximate errors relate not only to fractional order but also to time $t$ and increase rapidly with time $t$. This method can only be applied within a certain time range and the time range is relevant to fractional order and fractional expansions. Then, many obtained achievements may be incorrect if the applicable conditions are not satisfied. Some examples presented in this paper verify our analysis.

Cooperative non-orthogonal multiple access (CNOMA) has been recently adapted with energy harvesting (EH) to increase energy efficiency and extend the lifetime of energy-constrained wireless networks. In EH, two protocols are usually used for CNOMA, namely, power splitting (PS) and time switching (TS). In order to improve the existing EH protocols, this paper investigates a hybrid EH protocol-assisted CNOMA, which is a combination of the two aforementioned main existing EH protocols. The end-to-end bit error rate (BER) and outage probability (OP) expressions of users in our scheme are derived over Nakagami-m fading channels. For the sake of comparison and to highlight the achievable gains, the performance of the hybrid EH (HEH) protocol is compared with the benchmark schemes (i.e., existing EH protocols and no-EH). Based on extensive simulations, it is shown that the analytical results match perfectly with simulations which demonstrates the correctness of the derivations. Numerical results clearly indicate the superiority of the proposed scheme over all the considered benchmarks. In addition, we discuss the optimum value of EH factors to minimize the error and outage in the proposed scheme and show that an optimum value can be obtained according to channel parameters.

In this work, we derive the spectral efficiency, secrecy outage probability, and bit error rate of a communication system assisted by a large intelligent surface (LIS). We consider a single-antenna user and an array of antennas at the transmitter side and the possibility of a direct link between transmitter and receiver. Additionally, there is a single-antenna eavesdropper with a direct link to the transmitter, which is modeled as a Nakagami-m distributed fading coefficient. The channels from transmitter to the LIS and from the LIS to the user may or may not have the line-of-sight (LoS) and are modeled by the Nakagami- m distribution. Moreover, we assume that the LIS elements perform non-ideal phase cancellation leading to a residual phase error that assumes a Von Mises distribution. We show that the resulting channel can be accurately approximated by a Gamma distribution whose parameters are analytically estimated using the moments of the equivalent signal-to-noise ratio. We also provide an upper bound for the error probability for M-QAM modulations. With the derived formulas, we analyze the effect of the strength of the LoS link by varying the Nakagami parameter, m.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

In this paper, we propose a pre-configured error pattern ordered statistics decoding (PEPOSD) algorithm and discuss its application to short cyclic redundancy check (CRC)-polar codes. Unlike the traditional OSD that changes the most reliable independent symbols, we regard the decoding process as testing the error patterns, like guessing random additive noise decoding (GRAND). Also, the pre-configurator referred from ordered reliability bits (ORB) GRAND can better control the range and testing order of EPs. Offline-online structure can accelerate the decoding process. Additionally, we also introduce two orders to optimize the search order for testing EPs. Compared with CRC-aided OSD and list decoding, PEPOSD can achieve a better trade-off between accuracy and complexity.

The intercomparison among different atmospheric monitoring systems is key for instrument calibration and validation. Common cases involve satellites, radiosonde, radio occultation (e.g. GNSS-RO) and atmospheric model outputs (e.g. ERA5 reanalysis). Since instruments and/or measures are not perfectly collocated, the miss-collocation uncertainty must be considered in the related intercomparison uncertainty budgets.

Culture exploits the acquisition of meaningful content by crafting regimes of shared attention, determining what is relevant, valuable, and salient. Culture changes the field of relevant social affordances worthy of being acted upon in a context-sensitive manner. When relevant affordances are highly weighted, their attentional capture and their salience increase the probability of them being enacted due to the associated expectation for minimizing prediction error. This process is known as active inference. In the digital era, individuals need to infer the action-related attributes of digital cues, here characterized as digital affordances. The digital affordances of digital social platforms are of particular interest here. Digital social affordances are defined as online possibilities of social interactions. By their own nature, these are salient because they are related to social interactions and relevant social cues. However, the problem of digital social platforms is that they are not equivalent to situated social interactions because their structure is built, mediated, and defined by third-parties with diverse interests. The third-parties behind the digital social platforms are using the same mechanism exploited by culture to manipulate the shared patterns of attention. Moreover, digital social platforms are deliberately designed to be hyper-stimulating, making digital social affordances highly rewarding and increasingly salient. This appropriation, for economic purposes, is an issue of great importance, especially as the COVID-19 pandemic brought deep global changes, pushing societies to an online digital way of life. Here, we examined different types of digital social affordances under an active inference view, placing them into two categories, those for self-identity formation, and those for belief-updating. This paper aims to analyze digital social affordances in light of the prediction error dynamics they might elicit to their users. Although each of the analyzed digital social affordances allows different epistemic and instrumental digital actions, they all share the characteristic of having an "easy" and a fast expected rate of error reduction. Here, we aim to provide a new hypothesis about how the design behind digital social affordances is built on our natural attractiveness to minimize prediction error and the resulting positive embodied feelings when doing so. Finally, it is suggested that because digital social affordances are becoming highly weighted in the field of affordances, this might be putting at risk our context-sensitive grip on a rich, dynamic and varied field of relevant affordances.

Fundamentals of Laparoscopic Surgery (FLS) is a training module designed to provide basic surgical skills. During skill training of the FLS "suturing and intracorporeal knot-tying" task – the most difficult among the five psychomotor FLS tasks, learning from errors is one of the basic principles of motor skill acquisition where appropriate contextual switching of the brain state on error is postulated. This study investigated changes in the brain state following an error event based on the fusion of simultaneously acquired functional near-infrared spectroscopy (fNIRS) and electroencephalography (EEG) signals. Here, human error processing is postulated to differentiate experts from novices based on the differences in the error-related chain of mental processes. Thirteen right-handed novice medical students and nine expert surgeons participated in this study. Error-related microstate analysis was performed using 32-channel EEG data at a high temporal resolution. Six microstate prototypes were identified from combined EEG data from experts and novices during the FLS task. Analysis of variance (ANOVA) found that the proportion of the total time spent in different microstates during the 10 sec error epoch was significantly affected by the skill level (p<0.01), microstate type (p<0.01), and the interaction between the skill level and the microstate type (p<0.01). Then, the EEG band power (1-40Hz) related to slower oxyhemoglobin (HbO) changes were found using regularized temporally embedded Canonical Correlation Analysis of the fNIRS-EEG signals. The HbO signal from the fNIRS channel overlying ‘Frontal_Inf_Oper_L’, ‘Frontal_Mid_Orb_L’, ‘Postcentral_L’, ‘Temporal_Sup_L’, ‘Frontal_Mid_Orb_R’ cortical areas from Automatic Anatomical Labelling showed significant (p<0.05) difference between experts and novices in the 10-sec error epoch. Here, the frontal/prefrontal cortical areas are postulated to be related to the perception and the activation of the primary somatosensory cortex at the postcentral cortical area is hypothesized to be related to the action underpinning perception-action coupling model for the error-related chain of mental processes. Therefore, our study highlighted the importance of error-related brain states from portable brain imaging when comparing complex surgical skill levels.

Capacity Expansion Models (CEMs) are optimization models used for long-term energy planning on national to continental scale. They are typically computationally demanding, thus in need of simplification, where one such simplification is to reduce the temporal representation. This paper investigates how using representative periods to reduce the temporal representation in CEMs distorts results compared to a benchmark model of a full chronological year. The test model is a generic CEM applied to Europe, equipped with a novel formulation for storage in model versions with reduced temporal representation. We test the performance of reduced models at penetration levels of wind and solar of 90%. Three measures for accuracy are used: (i) system cost, (ii) total capacity mix and (iii) regional capacity. We find that: (i) the system cost is well represented (~5% deviation from benchmark) with as few as ten representative days, (ii) the capacity mix is in general fairly well (~20% deviation) represented with 50 or more representative days, and (iii) the regional capacity mix displays large deviations (>50%) from benchmark for as many as 250 representative days. We conclude that modelers should be aware of the error margins when presenting results on these three aspects.

Linear regression is a basic tool in mobile robotics, since it enables accurate estimation of straight lines from range-bearing scans or in digital images, which is a prerequisite for reliable data association and sensor fusing in the context of feature-based SLAM. This paper discusses, extends and compares existing algorithms for line fitting applicable also in case of strong covariances between the coordinates at each single data point, which must not be neglected if range-bearing sensors are used. Besides, particularly the determination of the covariance matrix is considered, which is required for stochastic modeling. The main contribution is a new error model of straight lines in closed form for calculating fast and reliably the covariance matrix dependent on just a few comprehensible and easily obtainable parameters. The model can be applied widely in any case when a line is fitted from a number of distinct points also without a-priori knowledge of the specific measurement noise. By means of extensive simulations the performance and robustness of the new model in comparison to existing approaches is shown.

We present a general theory of estimation of analysis error covariances based on cross-validation as well as a geometric interpretation of the method. In particular we use the variance of passive observation–minus-analysis residuals and show that the true analysis error variance can be estimated, without relying on the optimality assumption. This approach is used to obtain near optimal analyses that are then used to evaluate the air quality analysis error using several different methods at active and passive observation sites. We compare the estimates according to the method of Hollingsworth-Lönnberg, Desroziers et al., a new diagnostic we developed, and the perceived analysis error computed from the analysis scheme, to conclude that, as long as the analysis is near optimal, all estimates agree within a certain error margin.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

Spatial regression models have garnered significant attention across several disciplines, including functional magnetic resonance imaging analysis, econometrics, home price analysis, and many other domains. The phenomenon of sparsity is often found in nature, when a limited number of factors contribute significantly to the overall variation. Spatial regression models frequently use sparsity to indicate less complex computational and more superficial covariance structures. The spatial error model is a significant spatial regression model that focuses on the geographical dependence present in the error terms rather than the response variable. This study proposes an effective approach for estimating the vector of regression coefficients in the spatial error model, taking into consideration of the prior knowledge that some coefficients are insignificant and there is multicollinearity among the regressors. It also introduces pretest and shrinkage ridge estimators for spatial error regression models, evaluating their performance compared to traditional maximum likelihood estimators. It also assesses their efficacy using real-world data and bootstrapping techniques for comparison purposes.

Tipping bucket rain gauges (TBRs) have been, and apparently will continue to be one of the most widely used pieces of equipment for rainfall monitoring, being frequently used for the calibration, validation and downscaling of radar and remote sensing data, due to their major advantages–low cost, simplicity, and low energy consumption. Thus, many works have focused and continue to focus on their main disadvantage–measurement biases (mainly in wind and mechanical underestimations). However, despite arduous scientific effort, calibration methodologies are not frequently implemented by monitoring networks operators or data users, propagating bias in databases and in the different applications of such data, causing uncertainty in the modeling, management, and forecasting in hydrological research, mainly due to a lack of knowledge. Within this context, this work presents a review of the scientific advances in TBR measurement uncertainties, calibration, and error reduction strategies from a hydrological point of view, by describing different rainfall monitoring techniques in Section 2, summarizing TBR measurement uncertainties in Section 3, focusing on calibration, and error reduction strategies in Section 4, a discussion and perspectives in Section 5, and conclusions in Section 6, providing an overview of the of the state of the art and future perspectives of the technology.

We propose an approach for estimating the error in depth data provided by generic 3D sensors, which are modern devices capable of generating an image (RGB data) and a depth map (distance) or other similar 2.5D structure (e.g. stereo disparity) of the scene. Our approach starts capturing images of a checkerboard pattern devised for the method. Then proceed with the construction of a dense depth map using functions that generally comes with the device SDK (based on disparity or depth). The 2D processing of RGB data is performed next to find the checkerboard corners. Clouds of corner points are finally created (in 3D), over which an RMS error estimation is computed. We come up with a multi-platform system and its verification and evaluation has been done, using the development kit of the board nVIDIA Jetson TK1 with the MS Kinects v1/v2 and the Stereolabs ZED camera. So the main contribution is the error determination procedure that does not need any data set or benchmark, thus relying only on data acquired on-the-fly. With a simple checkerboard, our approach is able to determine the error for any device. Envisioned application is on 3D reconstruction for robotic vision, with a series of 3D vision sensors embarked in robots (UAV of type quadcopter and terrestrial robots) for high-precision map construction, which can be used for sensing and monitoring.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Highly-skilled migrants and refugees finding employment in low-skill vocations, despite professional qualifications and educational background, has become a global tendency, mainly due to the language barrier. Employment prospects for displaced communities are mostly decided by their knowledge of the sublanguage of the vocational domain they are interested in working. Common vocational domains include agriculture, cooking, crafting, construction, and hospitality. The increasing amount of user-generated content in wikis and social networks provides a valuable source of data for data mining, Natural Language Processing and machine learning applications. This paper extends the contribution of the authors’ previous research on automatic vocational domain identification by further analyzing the results of the machine learning experiments with the domain-specific textual data set, considering 2 research directions: a. predictions analysis and b. data balancing. Wrong predictions analysis and the features that contributed to misclassification, along with correct predictions analysis and the features that were the most dominant, contributed to the identification of a primary set of terms for the vocational domains. Data balancing techniques were applied on the data set to observe their impact on the performance of the classification model. A novel 4-step methodology is proposed in this paper for the first time, consisting of successive applications of SMOTE oversampling on imbalanced data. Data oversampling obtains better results than data undersampling in imbalanced data sets, while hybrid approaches perform reasonably well.

Quantum physics is intrinsically probabilistic. The entropy of a quantum state quantifies the amount of randomness (or information loss) of such state. The degrees of freedom of a quantum state are position and spin, and upon their specification Born's rule in phase space defines randomness. We focus on the spin degree of freedom and elucidate the spin entropy. Then, we present some of its properties and show how entanglement increases spin entropy. Some speculative predictions on the decay of the $Z^0,W^{+,-}$ gauge bosons conclude the paper.

Viruses have established symbiotic relationships with almost every other living organism on Earth and at all levels of biological organisation, from other viruses up to entire ecosystems. In most cases, peacefully coexisting with their hosts, but in most relevant cases, parasitising them and inducing diseases. Viruses are playing an essential role in shaping the eco-evolutionary dynamics of their hosts, and have been also involved in some of the major evolutionary innovations either by working as vectors of genetic information or by being themselves coopted by the host into their genomes. Viruses can be studied at different levels of biological organisation, from the molecular mechanisms of genome replication, gene expression and encapsidation, to global pandemics. All these levels are different and yet connected through the presence of threshold conditions allowing for the formation of a capsid, the loss of genetic information or epidemic spreading. These thresholds, as it occurs with temperatures separating phases in a liquid, define sharp qualitative types of behaviour. These {\em phase transitions} are very well known in Physics. They have been studied by means of simple, but powerful models able to capture their essential properties, allowing to understand them. Can the physics of phase transitions be an inspiration for our understanding of viral dynamics at different scales? Here we review well-known examples of transition phenomena in virology and their simplest mathematical modelling approaches. We suggest that the advantages of abstract, simplified pictures used in Physics are also the key to properly understand the origins and evolution of complexity in viruses. By means of several examples, we explore this multilevel landscape and how minimal models provide deep insights into a diverse array of problems. The relevance of these transitions in connecting dynamical patterns across levels and their evolutionary and clinical implications are outlined.

Empirical equations representing, interpolating and smoothing groups of measurement results by regression methods are in widespread use in metrology and other fields of science and engineering. Standard equations for the propagation of measurement uncertainties to values computed from such equations are available but suffer from a lack of general acceptance and are only infrequently applied in practice. One reason for the slow uptake is the lack of clear methods to account for systematic error. In this paper, uncertainty propagation equations in terms of covariance matrices are generalized to allow for systematic errors in least-squares regression, and effects of the resulting uncertainties are investigated analytically. A stochastic ensemble model of systematic error is proposed for the computation of the non-diagonal elements of the weight matrix of the Generalized Least-Squares method (GLS) from the measurement uncertainty. A GLS projector formalism is described which separates the effects of measurement scatter on values calculated by the equation from those on the related “residuals”, i.e., the residual errors in the fitted data. The same projectors act similarly on the associated uncertainties and covariance matrices and permit the effects of systematic errors on the simulation covariance to be quantified. It is demonstrated that, in order to include systematic errors in the uncertainty estimates of GLS, covariance matrices may be substituted by novel, specifically defined dispersion matrices that are not specified yet by the GUM[1]. Systematic measurement errors may be estimated from various sources; a particularly easy way suggested here involves analyzing the structure in the regression residuals. It is demonstrated that GLS projectors exhibit inherent features of “error blindness” also with respect to systematic errors. [1] GUM: Guide to the Expression of Uncertainty in Measurement, http://www.bipm.org/en/publications/guides

Quantum image representation is a widely researched area of quantum computing. Currently developed methods use angle parameter of the rotation gate (e.g., the FRQI method), sequences of qubits (ex. NEQR method) or phase shift (ex. LPIQE method) for storing color information of pixels. All of those methods are affected by decoherence and other classical and quantum noise, which is an inseparable part of quantum computing in a NISQ (Noisy Intermediate Scale Quantum) era. These all phenomenons influence the measurements, its probability distribution over the measurement basis and, as the result, makes the extracted images not even similar to those, which was stored in quantum computers. Since this process is, in its foundation, quantum as well, the computational reversal of this process is possible. There are a lot of methods for error correction, mitigation and reduction, but all of them use quantum computer time, or additional qubits to achieve desired result. We report a successful use of the Generative Adversarial Network tuned for image-to-image translation in conjunction with PDU method, for error reduction in images encoded using LIPQE (Local Phase Image Quantum Encoding) method.

Aimed for the difficulty and complexity of detecting the piston error for segmented telescope, this paper proposed a new piston error measurement method based on a hybrid artificial neural net-work. Firstly, we use Resnet network to learn the mapping relationship between the focal plane degradation image and the signs of the piston error. Then, based on the established theoretical re-lationship between modulation transfer function and the piston error, BP neural network is used here to learn the mapping relationship between the MTF and the absolute value of the piston error. After the training of the hybrid network is completed, a wide-range and high-precision detection of the piston error of the sub-mirrors can be achieved using the combined output of the two net-works only a focal plane image of a point source with broadband illumination is used as input. The detection range can reach the whole coherent length of the input broadband light, and the detec-tion accuracy can reach 10nm. The method proposed in this paper has the advantages of high de-tection accuracy, wide detection range, low hardware cost, small network scale and low training difficult.

Projected future sea level rise and marine storminess is a serious threat for beaches as they induce beach flooding and erosion. Among other factors, wave runup play an important role in beach evolution and must be robustly assessed. However, little attention has been paid to the uncertainties associated to its characterization and how do they compare to other sources of uncertainty. As a first step towards this goal, we have quantified the impact of several sources of error in the estimation of wave runup on sandy beaches. Understanding what factors are more influential in the quality of the results will help to determine the main sources of uncertainty in beach flooding projections. To reach that goal, a calibrated state-of-the-art numerical modelling system has been setup for two beaches in the Mallorca islands (NW Mediterranean). The system has been forced with the best available information of nearshore incoming waves and has been validated against observations to define the benchmark quality. To determine the key factors affecting the quality of the system’s results, different systems configurations have been tested with different degrees of complexity.Our results show that using the most sophisticated modelling system with the best information on boundary conditions, bottom bathymetry, and submerged vegetation leads to a swash RMSE comparable to the standard deviation of the observed swash. We have also found that the choice of lateral boundary conditions (i.e., source of information for the incoming waves) can double the RMSE and induce large biases. Our results also show that using a simple empirical approach usually underestimates the wave runup. However, in locations with vegetated seabed there is a compensation error, and the empirical approach can lead to acceptable results if forced by nearshore waves. In addition, we have compared the error estimates obtained with uncertainties associated to projected sea level rise. Our findings suggest that the uncertainty associated with wave runup modelling should be considered in the assessment of the total uncertainty of future beach flooding, since the analysis performed indicates that this uncertainty can account for between 16% to 60% of the uncertainties linked to mean sea level projections.

A drug repositioning effort supported the possible use of the anti-HIV drug etravirine as a treatment for Friedreich Ataxia (FRDA). Etravirine increases frataxin protein and corrects the biochemical defects in cells derived from FRDA patients. Because of these findings, and since etravirine displays a favorable safety profile, we conducted this pilot open-label phase 2 clinical trial assessing the safety and potential efficacy of etravirine in FRDA patients. Thirty-five patients were stratified into 3 severity groups and randomized to etravirine 200 mg/day or 400 mg/day. They were treated for 4 months. Efficacy endpoints were represented by changes in peak oxygen uptake and workload as measured by incremental exercise test, SARA score, cardiac measures, measures of QoL and disability. Data were collected 4 months before the start of the treatment (T-4), at the start (T0), at the end (T4) and 4 months after the termination of the treatment (T+4). Etravirine was well tolerated. Etravirine completely stopped the progression of the SARA score during the 4-months treatment period, compared to the 4 months pre and post treatment. It increased peak workload, while the improvement of peak oxygen uptake was not statistically significant. No changes in the cardiac measures were observed. Health and QoL measures showed a worsening at the suspension of the drug. In this open trial etravirine significantly improved neurological function and was generally safe and reasonably tolerated. This suggests that etravirine represents a potential therapeutic agent in FRDA deserving testing in a randomized placebo controlled clinical trial.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

We found an important fact that the beam footprint line of Ping will intersect with the real water depth when the initial incidence angle is about 45°, and sound velocity error hardly has an effect on it. This is contrary to our previous experience that the soundings of the central beam of multi-beam bathymetric system (MBS) is the most accurate. Firstly, the influence of sound velocity errors on central beam and seafloor topography distortion was analyzed. Secondly, the process of proving this fact was given, and the topography correction method was proposed by compensating the sound velocity profile area (SVP area). Finally, we showed in the first simulation of four type errors in SVPs that this fact is verified. The topography correction method used in the second simulation to correct the topography distortion of the first simulation is also verified.

This study employed the Fully Modified Ordinary Least Squares (FMOLS) and the Error Correction Model (ECM) to investigate the long-run and short-run determinants of unemployment rate in Nigeria. To achieve this annual data on unemployment rate, inflation rate, interest rate, exchange rate and population growth from 1981 to 2016 was collected from Central Bank Statistical Bulletins and the World Bank website. The ADF test revealed that the macroeconomic variables are stationary at first difference while the Cointegration test revealed that the variables are cointegrated. Using unemployment rate as dependent variable, the FMOLS model revealed that exchange rate and population growth are positively significantly related to unemployment rate, interest rate and inflation rate were negatively related to unemployment rate but only interest rate was significant. The short run relationship revealed that the coefficient of the ecm(-1) is negative and statistically significant at 5% level indicating that the system corrects its previous period disequilibrium at the speed of 48.93% yearly. This study concludes that high exchange rate and population growth can lead to increase in unemployment rate in Nigeria while the government should develop the industrial sector and non-oil sector in order to generate employment and boost export in Nigeria.

Laser scanning 3D imaging technology, because it can get accurate three-dimensional surface data, has been widely used in the search for wrecks and rescue operations, underwater resource development, and other fields. At present, the conventional underwater rotating laser scanning imaging system maintains a relatively fixed light window. However, in low-light situations underwater, the rotation of the scanning device causes some degree of water fluctuation, which warps the light strip data that the system sensor receives about the object's surface. To solve the problem, this research studies an underwater 3D scanning and imaging system that makes use of a fixed-light window and a spinning laser (FWLS). A refraction error compensation algorithm is investigated that is based on the fundamentals of linear laser scanning imaging and the dynamic refraction mathematical model is established by the motion of the imaging device. During the imaging process, the incident angle between the laser and the light window varies due to the scanning mode of the system. The experimental results show that the reconstruction radius error is reduced by 60% (from 2.5 mm to about 1 mm) when the measurement data for a standard sphere with a radius of 20 mm are compensated. Moreover, the compensated point cloud data exhibits a higher degree of correspondence with the model of the standard spherical point cloud. This study has a specific reference value for the refractive error analysis of an underwater laser scanning imaging system, and it provides certain research ideas for the subsequent refractive error analysis of various scanning imaging modalities.

In this work, in spite of Milne’s recommendation using the three-point Newton–Cotes open formula (Milne’s rule) as a predictor rule and three-point Newton–Cotes closed formula (Simpson’s rule) as a corrector rule for 4-th differentiable functions with bounded derivatives. There is still a great need to introduce such formulas in other Lp spaces. Often, we need to approximate real integrals under the assumptions of the function involved. Because of that, the aim of this work is to introduce several Lp error estimates for the proposed perturbed Milne’s quadrature rule. Numerical experiments showing that our proposed quadrature rule is better than the classical Milne rule for certain types of functions are provided as well.

Previously, using the conjugate frame-based reconciliation approach, we defined a method to correct errors produced in pairs of non-orthogonal quantum states that are transmitted through a quantum key distribution (QKD) link. The security of the frame-based reconciliation was discussed in order to deal with Photon Number Division (PNS) attack and Intercept and Forward (IR) attack, among others. However, until the time of publication we did not have the distillation software to test our method. In this article, following the conjugate frame distillation method, we present the implementation of the post-processing system that demonstrates that it is capable of correcting errors in the presence of error rates close to unity. The system shows that when the number of double-sensing events at Bob's station is as low as 100, the number of secret bits stays above 4500 bits in about 12 seconds, giving a secret rate of 375 bits per second while that the channel error rate reaches 90\%.

In this work we develop a new algorithm for efficient computation of the Voigt/complex error function. In particular, in this approach we propose a two-domain scheme where number of the grid-points is dependent on the input parameter $y$. The error analysis we performed shows that the MATLAB implementation meets the requirements for radiative transfer applications involving the HITRAN spectroscopic database. The run-time test shows that this MATLAB implementation provides rapid computation especially at smaller range of the parameter x.

In addition to the traditional QoS metrics of delay, delay jitter, and packet loss probability (PLP), Quality of Experience (QoE) is now widely accepted as a numerical proxy for actual user experience. The literature has reported many mathematical mappings between QoE and QoS. These QoS parameters are measured by the network providers using sampling. There are some papers studying sampling errors in QoS measurements; however there is no account of propagation of these sampling errors to QoE evaluation. In this paper, we used industrially acquired measurements of PLP and jitter to evaluate the sampling errors and correlation in measurements. Focussing on Video-on-demand (VoD) applications, we use subjective testing and regression to map QoE metrics onto PLP and jitter. The resulting mathematical functions of QoE and theory of error propagation was used to evaluate the propagated error in QoE, and this error was represented as confidence interval. Using the guidelines of UK government for sampling, our results indicate that confidence intervals around estimated QoE in a busy hour can be between MOS=1 to MOS=5 at targeted operating point of QoS parameters. These results are a new perspective on QoE evaluation, and are of great significance to all organisations that need to estimate the QoE VoD applications precisely.

This paper proposes a real-time local positioning system (RT-LPs) utilizing a mobile platform equipped with three anchor nodes placed in a right-angle triangle formation for a real-time locating system (RTLS). After deriving an analytic formula to calculate the target position utilizing the measured distances among anchor nodes and the target node, we find that four parameters have an effect on the position error of the target node. The spacing between anchors is a design parameter that must be large enough to the reduce position error. However, the distance from the anchor node to the target node is an operation parameter that must be small enough to reduce the position error. Additionally, the measured ranges among the anchors and the target node have probabilistic distributions with a mean and variance, which are dominant parameters that have effects on the position error. A comparison study was conducted to determine the effects of the parameters of the target position in both a simulation and an experiment, showing rates of approximately 4% ~ 10%. These findings indicate that our simulation can work properly with the proposed method after assuming that the distance error is a Gaussian model.

Multi-step ahead streamflow forecasting is of practical interest for the operation of hydropower reservoirs. We provide generalized results on the error evolution in multi-step ahead forecasting by conducting several large-scale experiments based on simulations. We also present a multiple-case study using monthly time series of streamflow. Our findings suggest that some forecasting methods are more useful than others. However, the errors computed at each time step of a forecast horizon within a specific case study strongly depend on the case examined and can be either small or large, regardless of the forecasting method used and the time step of interest.

Viral infection can regulate the cell cycle, thereby promoting viral replication. Hijacking and altering the cell cycle are important for the virus to establish and maintain latent infection. Previously, Spodoptera exigua multiple nucleopolyhedrovirus (SeMNPV) latently infected P8-Se301-C1 cells, which grew more slowly than Se301 cells and interfered with homologous SeMNNPV superinfection, were established. However, the effects of latent and superinfection with baculoviruses on cell cycle progression remain unknown. In this study, the cell cycle profiles of P8-Se301-C1 cells, and SeMNPV or Autographa californica mutiple nucleopolyhedrovirus (AcMNPV) infected P8-Se301-C1 cells were characterized by flow cytometry. The results showed that replication-related genes MCM4, PCNA, and BAF were down-regulated (p < 0.05) in P8-Se301-C1 cells and the S phase of P8-Se301-C1 cells was longer than that of Se301 cells. P8-Se301-C1 cells infected with SeMNPV did not arrest in G2/M phase and or affect the expression of Cyclin B and cyclin-dependent kinase 1 (CDK1). Furthermore, when P8-Se301-C1 cells were infected with SeMNPV after synchronized treatment with hydroxyurea and nocodazole, light microscopy and qRT-PCR analysis showed that compared with unsynchronized cells and S and G2/M phase cells, SeMNPV-infected P8-Se301-C1 cells in G1 phase induced G2/M phase arrest, and the amount of virus adsorption and intracellular viral DNA replication were significantly increased (p < 0.05). In addition, the BV production and the OB containing cells were both increased at 120 h post-infection (p < 0.05). The expression of Cyclin B and CDK1 was significantly down-regulated at 48 h post infection (p < 0.05). Finally, arrest of SeMNPV-infected G1 phase cells in the G2/M phase increased BV production (p < 0.05) and the number of OB containing cells. In conclusion, G1 phase infection and G2/M arrest are favorable to SeMNPV proliferation in P8-Se301-C1 cells, thereby alleviating the homologous superinfection exclusion. The results contribute to a better understanding of the relationship between baculoviruses and insect cell cycle progression regulation.

The positional deviation of the Automatic Emergency Call System (AECS) under collision conditions brings difficulties for post-rescue operations. Currently, there is a lack of analysis on the system operating conditions during collisions in the reliability assessment methods for the Global Navigation Satellite System (GNSS) deployed in AECS. Therefore, this paper establishes an in-vehicle collision environment simulation model for emergency calls to explore the influence of parameters such as temperature and vibration on the data deviation of the simulated GNSS system. We also propose environmental limits applicable to comprehensive AECS tests, which can objec-tively evaluate the reliability of AECS and provide data support for AECS bench test. Through the satellite signal-based semi-physical simulation, AECS is subjected to bench test under different operating conditions. The findings of this study demonstrate that the occurrence of random vibra-tion and impact stress, induced by vibration, exerts considerable disruptive effects on positional signal data during collisions. Consequently, it leads to substantial interference with the accurate detection of post-collision satellite positioning information. When the simulation operates under a 2.4gRMS vibration condition, the maximum phase noise error in the positioning system is 8.95%, which does not meet the AECS test accuracy requirements. On the other hand, the semi-simulation system is less affected by temperature changes, and at the maximum allowable temperature dif-ference of the equipment, the maximum phase noise error in the simulated signal is 2.12%. Therefore, based on the influence of phase noise variation on the accuracy of satellite signal simulation, nec-essary environmental conditions for AECS test are obtained, including the temperature consistent with the maximum operating temperature of the vector generator and the vibration Power Spectral Density (PSD) lower than 1.2gRMS.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

The idealized rhombohedral unit cell of boron carbide is formed by a 12-atom icosahedron and a 3-atom linear chain. Phase transitions are second order and caused by the exchange of B and C sites or by vacancies in the structure. Nevertheless, the impact of such minimal structural changes on the properties can be significant. As the X-ray scattering cross sections of B and C atoms are very similar, the capability of X-ray fine structure investigation is restricted. Phonon spectroscopy helps closing this gap. Phase transitions known to date have been identified due to significant changes of properties: (1) The phase transition near the chemical composition B8C by clear change of the electronic structure; (2) The endothermic temperature-dependent phase transition at 712 K by the according change of specific heat; (3) The high-pressure phase transition at 33.2 GPa by the drastic change of optical appearance from opacity to transparency. These phase transitions affect IR- and Raman-active phonons and other solid-state properties. The phase transitions at B~8C and 712 K mean that a well-defined distorted structure is converted into another one each. In the high-pressure phase transition, an apparently well-defined distorted structure changes into a highly ordered one. In all these cases, the distribution of polar C atoms in the icosahedra plays a crucial role.

Quantum physics through the lenses of Bayesian statistics consider probabilities to be degree of believes or knowledge and subjective. A Bayesian derivation of the probability density function in phase space is presented. The entropy proposed by Geiger and Kedem \cite{GeiKed2022a,GeiKed2022b} in phase space is expanded to define quantitatively interference and entanglement. Comparisons between each of these two quantities and the entropy are made. A brief presentation of entanglement in phase space to the spin degree of freedom and to mixed states completes the work.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

We study the deterministic dynamics of N point particles moving at constant speed in a 2D table made of two polygonal urns connected by an active rectangular channel, which applies a feedback-control on the particles, inverting the horizontal component of their velocities, when their number in the channel exceeds a fixed threshold. Such a bounce--back mechanism is non-dissipative: it preserves volumes in phase space. An additional passive channel closes the billiard table forming a circuit in which a stationary current may flow. Under specific constraints on the geometry and on the initial conditions, the large N limit allows nonequilibrium phase transitions between homogeneous and inhomogeneous phases. The role of ergodicity in making a probabilistic theory applicable is discussed both for rational and irrational urns. The theoretical predictions are compared with the numerical simulation results. Connections with the dynamics of feedback-controlled biological systems are highlighted.

We show that the van der Waals gas does not exhibit just the celebrated liquid-gas 1 transition but also a quantum-classical one. We study the issue with reference to the LMC statistical 2 complexity and in relation to the order-disorder contrast.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

This study presents the numerical investigation of bioconvective nanofluid (NF) flow compris-ing gyrotactic microorganisms through convective boundary conditions (CBC) enclosing heat and mass transmission analysis above an inclined extending cylinder. Via appropriate transfor-mation, the set of Partial Differential Equations is transformed into a scheme of nonlinear ODEs. A new set of variables are presented in the directive to get the first-order convectional equations and, then solved numerically by using bvp4c. The influence of several factors on velocity, ener-gy, concentration, and the density of motile microorganisms (DMM) is investigated and exam-ined. The analysis describes and addresses all physical measures of concentration such as Skin Friction (SF), Sherwood number (SN), DMM, and Nusselt number (NN). The present conse-quences display a validation with published. For confirmation of bvp4c, the ND-solve approach is also applied. Error analysis is also examined for the confirmation of the mathematical model.

Infectious mononucleosis (Mono) is mostly caused by the Epstein-Barr virus (EBV), and can spread through infected people sharing food and drinks with others. Once this virus gets into your system, it is there to stay. The virus can get activated when a person has low immunity and can cause major complications. Furthermore, if physicians miss the diagnosis of this disease, and prescribe penicillin-based antibiotics, it can cause severe rash and adverse reactions that compromise patient safety. This paper develops a simple Hidden Markov Model using which a Viterbi algorithm provides the maximum a posteriori probability estimate for the most likely hidden state path, given a sequence of symptoms arising as observations from a patient with hidden EBV positive or negative states. Apart from bringing awareness to help reduce missed diagnoses and subsequent adverse events, this work provides a tool for health care systems to better incorporate prompts during electronic medical record (EMR) interactions to help physicians catch potential missed diagnoses during a visit. This research demonstrates how statistical models can be used to assess likelihood of underlying conditions that require tests to be offered by physicians in order to make a definitive diagnosis. The model developed and applied herein for estimating likelihood of EBV infection from a series of observations has the potential to alter guidelines within healthcare systems to ensure that the safety of patients, particularly teens, is not compromised due to a lack of definitive diagnosis for Mono at point of care.

Building fires are preventable incidents that have proven to be both deadly and costly. Addressing their root causes will lead to safer neighbourhoods for families and businesses to live and operate in. Multiple studies have established the effect of residents’ socioeconomic compositions on an area’s building fire rates; however, the existing model based on the classical stepwise regression procedure has several limitations. This paper aims to construct a more accurate predictive model of building fire rates based on a set of explanatory socioeconomic variables. In building the socioeconomic model, a backward elimination by Robust Final Predictor Error (RFPE) criterion is proposed to enhance the forecasting capability of the model. The proposed method has been implemented on the census data and the fire incident data of the South East Queensland region in Australia. A cross-validation was then conducted to assess the model’s accuracy. In addition, comparative analyses of other elimination criteria, such as p-value, adjusted R-squared, Akaike’s Information Criterion (AIC), Bayesian Information Criterion (BIC) and predicted residual error sum of squared (PRESS), were conducted. The cross-validation analyses demonstrate that the proposed criterion is a more accurate predictive model based on a couple of goodness-of-fit measures. All in all, the RFPE equation was found to be a suitable criterion for the backward elimination procedure in the socioeconomic modelling of building fires.

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.