In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

In the electric distribution systems, the “Smart Grid” concept is implemented to encourage energy savings and integration of the innovative technologies, helping the Distribution Network Operators (DNOs) in choosing the investment plans which to lead the optimal operation of the networks and increasing the energy efficiency. In this context, a new phase load balancing algorithm was proposed to be implemented in the low voltage distribution networks with hybrid structures of the consumption points (switchable and non-switchable consumers). It can work in both operation modes (on-line and off-line), uploading information from different databases of the DNO which contain: the consumers’ characteristics, the real loads of the consumers integrated into the Smart Metering System (SMS), and the typical load profiles for the consumers non-integrated in the SMS. The algorithm was tested in a real network, having a hybrid structure of the consumption points, on a time interval by 24 hours. The obtained results were analyzed and compared with other algorithms from the heuristic (Minimum Count of Loads Adjustment algorithm) and the metaheuristic (Particle Swarm Optimization and Genetic Algorithms) categories. The best performances were provided by the proposed algorithm, such that the unbalance coefficient resulted in the smallest value (1.0017). The phase load balancing led to the following technical effects: decreasing the average current in the neutral conductor with 94% and for the energy losses with 61.75 %, and increasing the minimum value of the phase voltage at the farthest pillar with the 7.14 %, compared to the unbalanced case.

In the last years, the Distribution Grid Operators (DGOs) assumed transition strategies of the distribution grids towards an active area associated with the "Smart Grids" concept. They are considering the use of Artificial Intelligence techniques, combined with advanced technologies and real-time remote communication solutions of the enormous data amounts, to develop smart solutions into the small size distribution grids, also called microgrids (μGs). These solutions will provide support for the DGOs to ensure an optimal operation of the technical infrastructure of the μGs. In this context, a bi-level methodology for solving the phase load balancing problem in the μGs with complex topologies and a high number of single-phase consumers, considering a clustering-based selection criterion of the consumers for placement of the switching devices, was proposed in the paper. A real μG from a rural area, with 114 consumers integrated into the Smart Metering System (SMS), belonging to the DGO from Romania, was considered in testing the proposed methodology. An implementation degree of 17.5%, corresponding to the phase load balancing equipment installed to only 20 consumers from the μG, led to a faster computational time with 43% and reducing the number of switching operations by 92% than in the case of a full implementation degree (100%). The performance indicators related to the unbalance factor and energy-saving used in the evaluation of the technical benefits highlighted the efficiency of the proposed methodology.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

The ultimate aim of dynamic load balancing in cloud computing systems is to maximise the efficiency with which resources are utilised and workloads are distributed. Given that load balancing is a multi-objective process and that response time is a priority, the Harris hawk optimisation (HHO) algorithm was developed as a unique solution for dynamic load balancing. Based on burden distribution and resource utilisation, the HHO algorithm is responsible for dynamically assigning workloads to virtual machines (VMs). Through iterative interactions and position updates, the hawks investigate the solution space, determine the optimal method for dividing the work, and adapt to the ever-changing conditions of the workload. The HHO algorithm has been demonstrated to be effective and efficient in the management of dynamic load balancing via a series of experimental evaluations and comparisons with other load-balancing approaches. These discoveries have led to quicker response times and more efficient resource utilisation. Utilising the collaborative search behaviour of hawks, this technique provides a solution that is both practicable and effective for addressing load balancing concerns in dynamic scenarios.

With large-scale distributed generators (DGs) in an active distribution network (ADN), conventional load flow convergence failure is incurred by heavy power transmission. The Holomorphic Embedding Load Flow Method (HELM) has proven to be more robust than the Newton–Raphson method under heavy power transmission. At present, HELM is mainly designed for balanced transmission networks. In this study, we developed a three-phase HELM model to accommodate DGs, delta connection loads, and ZIP loads for ADN. The effectiveness and better performance of the proposed method under heavy load situations were validated using modified unbalanced IEEE 13, 34, 37, and 123 test feeders.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

With the progression of AI, embedding advanced AI technologies into small robotics and mobile devices has become essential, driving research towards lightweighting AI models. Our study enhances the EPINET depth estimation model for light field images, aiming for compactness and faster inference while preserving accuracy. We conducted two-step experiments aimed at enhancing inference efficiency: Initially, by adjusting input streams and convolution layers, we simplified the CNN model, achieving faster inference times at the cost of reduced accuracy. To address this reduction in accuracy, we then applied knowledge distillation, allowing the simplified model to learn from the original model’s more complex patterns. In our quantitative experiments using two error metrics, MSE (Mean Squared Error) and BadPix, we identified optimal knowledge positions and evaluated the required complexity for the student model. As a result, our method improved MSE by 21% and BadPix by 14% compared to training without it. Furthermore, the student model achieved an inference speed 13% faster than the teacher model and surpassed its accuracy by 10% in MSE. Additionally, we demonstrated that repeatedly applying our approach could further enhance both model compactness and accuracy.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

Background: Previous neuroimaging studies have identified brain regions related to respiratory motor control and perception. However, little is known about the resting-state functional connectivity (FC) associated with respiratory impairment. We aimed to determine the FC involved in mild respiratory impairment without changing the saturation of percutaneous oxygen. Methods: We obtained resting-state functional magnetic resonance imaging data from 36 healthy volunteers during normal respiration and mild respiratory impairment induced by resistive load (effort breathing). ROI-to-ROI and seed-to-voxel analyses were performed using Statistical Parametric Mapping 12 and the CONN toolbox. Results: Compared to normal respiration, effort breathing activated FCs within and between the sensory perceptive area of respiration (the postcentral gyrus, anterior insular cortex (AInsula), and anterior cingulate cortex) and visual cortex (the visual occipital, occipital pole (OP), and occipital fusiform gyrus). Graph theoretical analysis showed strong centrality in the visual cortex. A significant positive correlation was observed between the dyspnoea score (modified Borg scale) and FC between the left AInsula and right OP. Conclusions: These results suggested that the FCs within the respiratory sensory area via the network hub may be neural mechanisms underlying effort breathing and modified Borg scale scores.

This general review assesses the impact of physical exercise on oxidative and nitrosative stress and the counteractive role of antioxidants, drawing from a systematic literature search up to March 2024 in databases like PubMed and Web of Science. The review highlights studies on the effect of exercise on the production of reactive oxygen species (ROS) and reactive nitrogen species (RNS) and antioxidant responses in both human and animal models based on rigorous inclusion and exclusion criteria. Due to the variety of exercise types and participants' characteristics, a narrative synthesis approach was adopted. The findings indicate that moderate exercise boosts antioxidant defenses, known as hormesis, whereas excessive physical activity may increase oxidative and nitrosative damage. The review also explores the complex effects of antioxidant supplementation, revealing that while natural dietary antioxidants support health, high-dose supplements could potentially hinder positive adaptations to exercise. Recommendations for athletes and the general active population highlight the importance of balancing exercise and dietary intake to optimize health benefits. The review concludes with a call for more detailed research on tailored exercise and nutrition plans to dissect these intricate relationships further.

Present paper is dealing with the adaptive static balancing of robot or other mechatronic arms that are moving in vertical plane and whose static loads are variable, by using counterweights and springs. Some simple passive and approximate solutions are proposed and an example is shown. The active and exact solutions by using adaptive real time control in the case of unknown variation of static loads are simulated on VIPRO platform developed at Institute of Solid Mechanics of Romanian Academy.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Mechanical properties of cardiomyocytes from different transmural regions are heterogeneous in the left ventricular wall. The cardiomyocyte mechanical environment affects this heterogeneity because of mechano-electric feedback mechanisms. In the present study, we investigated the effects of load upon transmural differences in contraction of subendocardial (ENDO) and subepicardial (EPI) single cells isolated from the murine left ventricle. Various loads were applied to the cells using carbon fiber techniques for single myocytes. To simulate experimentally obtained results and to predict mechanisms underlying the cellular response to change in load, our mathematical models of the ENDO and EPI cells were used. Extent of the transmural gradient in the time course of contractions was independent of the loading conditions where unloaded and heavy loaded (isometric) contractions were examined, but the regional gradient of the relaxation time characteristics tended to decrease when the load decreased. Under auxotonic contractions, time to peak contraction (T_max) was significantly longer in ENDO cells than in EPI cells at low preload. An increase in preload (axial stretch) prolonged T_max in both cell types; however, the prolongation was greater in EPI cells, resulting in a decrease in transmural gradient in T_max at high preload. The [Ca²⁺]_i transient decay time constant was consistent with the greater preload dependency in T_max of EPI cells. Our modified mathematical models reproduced experimental results, suggesting that differences in cooperativity of cross bridges and calcium troponin C complex interactions between the ENDO and EPI cardiomyocytes may contribute to the different cellular responses to stretch, which may provide a decrease in transmural dispersion of cellular shortening in the intact heart.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

This study examined the impact of differences in fruit load of olive trees on the rate of stem refilling. The experiment was conducted in a commercial olive orchard over the consecutive years of 2021 and 2022, during which the biennial bearing cycle of olive trees resulted in minimal fruit production in 2021 and maximal production in 2022. The rate of stem refilling was determined by quantifying the differences in water volume traversing the apex and base of the principal branches of experimental trees using sap flow sensors. Concurrent measurements of tree water status were also conducted using psychrometers, while soil moisture content dynamics were continuously recorded. Results indicate that alternate bearing significantly influences the stem refilling process, while soil moisture availability also plays a pivotal role. Water reserves were more intensively utilized during the year of full production (“ON” year) primarily to fulfill the water demands of developing fruits. This replenishment occurred in various periods during the day, including early morning, afternoon, and night, when stomatal conductance measurements indicated stomatal closure. The study suggests a more intense replenishment of reserves during the night in "ON" year trees, irrespective of soil moisture, water vapor pressure deficit, or phenological fruit development stage.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

Due to related uncertainties brought by changes in energy consumption and the integration of rooftop photovoltaic systems, the accuracy and availability of load profiling data are difficult to achieve. However, project managers and planners use a precise load profile as a crucial tool when determining whether the feeder must be updated or de-loaded. The paper aims to create a non-intrusive monitoring system that predicts the synthetic load profiles behavior of energy consumption using a Light Gradient Boosted and Support Vector Machine (SVM) machine learning technique. The most effective ML algorithm is chosen, and it has the potential to be assessed and verified using validation curves, residuals model generation, and prediction error metrics based on the following key statistical indicators: Mean Absolute Error, Mean Square Error, Root Mean Square Error, R-Square, Root Mean Squared Logarithmic Error, and Mean Absolute Percentage Error. The most effective ML has the potential to be assessed and verified using validation curves, residual model generation, and prediction error metrics based on the following key statistical indicators. The result shows that the estimation of the Irms avg -based on LightGBM is more accurate than the SVM because of its quick, economical, and difficult to overfit, particularly with high-dimensional data, speed, and efficiency of the MAE (3.0698), MSE (15.2757), RMSE (3.9020), RMSLE (0.1433), and MAPE (0.0049) respectively. Additionally, the machine learning model shows that, when compared to the SVM, the LightGBM model had the highest accurate prediction, with R-Square values of 89.8%, 90.3%, and 88.5% for Irms_A_avg, Irms_B_avg, and Irms_C_avg, respectively for Brakfontein Substation supply region, and best represents a diverse customer base.

The success of Toxoplasma gondii (intracellular parasite) host cell invasion relies on the apical complex, a specialized microtubule cytoskeleton structure associated with secretory organelles. The genome encodes three isoforms of both α- and β-tubulin which are altered by specific post-translational modifications (PTMs), changing the biochemical/biophysical proprieties of microtubules, and modulating their interaction with associated proteins. Tubulin PTMs are a powerful and evolutionarily conserved mechanism to generate tubulin diversity, forming a biochemical ‘tubulin code’ that can be ‘read’ by microtubule-interacting factors. The T. gondii tubulin PTMs are: α-tubulin acetylation, α-tubulin detyrosination, Δ5α-tubulin, Δ2α-tubulin, α- and β-tubulin polyglutamylation, and α- and α-tubulin methylation. Tubulin glutamylation is a key candidate to assist microtubule remodeling in Toxoplasma, being involved in the regulation of microtubule stability, dynamics, interaction with motor proteins, and severing enzymes. The correct balance of tubulin glutamylation is achieved by the coordinated action of polyglutamylases and deglutamylating enzymes. In this work we will review and discuss the current knowledge on T. gondii tubulin glutamylation. By in silico identification of mammalian protein orthologs we explored and updated the identification of putative proteins related to glutamylation, contributing to a better understanding of the role of tubulin glutamylation in T. gondii.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Abstract Purpose: In this study, the Pre-implantation embryonic sex ratio in 125 couples who had three or more female children and underwent pre-implantation genetic diagnosis (PGD) for non-medical reason was included. Besides, we have aimed to find out whether these couples had more chances of getting a girl child once again. Methods: 125 couples who had three or more female offspring and those who underwent PGD for non-medical sex selection (XY) between 2015 and 2019 were included. Nuclear DNA was analyzed by Fluorescent in situ Hybridization (FISH). 2-chromosome (X, Y), 3-chromosome (21, X, Y), 5-chromosome (13, 18, 21, X, Y) probes were used for FISH. The standard protocol was followed for sperm processing and embryo culture for IVF and PGD. Result: Independent sample t-test showed that there is no significant difference between equal and unequal embryonic groups in patients’ age, husbands’ age, sperm count, sperm motility, total male embryos, total female embryos, normal male embryos, and normal female embryos. For patients with positive pregnancy outcome, 84.6% had unequal embryonic ratio while 15.4% had equal embryonic ratio. Similarly, patients those who were treated by short protocol had 85% of unequal embryonic ratio and 15% had equal ratio. Conclusion: Greater variability in the female to male embryos was found in these couples, confirms the fact that couples previously having girl offspring may predominantly not produce embryo of the same sex every time.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

In the dynamic landscape of Sabah's socio-economic development, the integration of AI technologies holds both promise and challenge. While AI has the potential to drive economic growth, enhance productivity, and elevate quality of life, it also brings forth concerns regarding job displacement, skill gaps, and unequal distribution of benefits. The latest research problem in the realm of AI and employment in Sabah revolves around ensuring inclusive and sustainable development amidst this technological disruption. This encompasses two key dimensions: skill development and education, and labor market dynamics. Addressing the research questions necessitates a multifaceted approach. Firstly, in the realm of skill development and education, there is a critical need to assess the adequacy of existing programs in equipping the workforce with AI-driven skills. Strategies such as promoting STEM education, fostering digital literacy, and facilitating lifelong learning initiatives, particularly among marginalized communities, are essential. Additionally, fostering collaboration between stakeholders and implementing curriculum reforms are pivotal steps in enhancing the alignment between educational curricula and the demands of an AI-driven economy.

This paper investigates the critical factors for balancing environmental sustainability and economic development through the lens of New Structural Economics. Specifically, we utilize the congruence index to access the alignment between local factor endowment structure and firm production input structure. Using a comprehensive manufacturing firm-level pollutant emissions dataset from the Yangtze River Economic Belt (YEB) region in China, we find that firms demonstrating higher congruence exhibit improved economic performance and alignment with comparative advantages. This not only contributes to increased economic efficiency for these firms but also leads to a reduction in pollutant emissions, including wastewater discharge and Chemical Oxygen Demand (COD) emissions. Our study provides valuable insights into achieving mutually beneficial environmental and economic outcomes.

This work investigates how to balance the electricity supply and demand in a carbon-neutral northern Europe. Applying a cost-minimizing electricity system model including options to invest in eleven different flexibility measures, cost-efficient combinations of strategies to manage varia-tions are identified. The results of the model are post-processed using a novel method to map the net load before and after flexibility measures are applied to reveal the contribution of each flexi-bility measure. The net load is mapped in the space spanned by the amplitude, duration, and number of occur-rences. The mapping shows that, depending on cost structure, flexibility measures contribute to reduce the net load in three different ways; 1) by reducing variations of long duration but low amplitude, 2) by reducing variations of high amplitude but short duration and low occurrence or 3) by reducing variations of high amplitude, short duration and high occurrence. It is found that cost-efficient variation management is achieved by combining wind and solar power and by combining strategies (1-3) to manage variations. The cost-efficient combination of strategies de-pends on electricity system context where electricity trade, flexible hydrogen and heat production (1) manage the majority of variations in regions with good conditions for wind power while sta-tionary batteries (3) are the main contributors in regions with good conditions for solar power.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

A defining feature of a productive infection is the co-opting of host cell resources for viral replication. Despite their repertoire of molecular functions, viruses subvert host defenses to take control of cellular factors such as RNA binding proteins (RBPs). RBPs are involved in virtually all steps of mRNA life forming ribonucleoprotein complexes (mRNPs) in a highly ordered and regulated process to control RNA fate and stability in the cell. Thus, the hallmark of this viral takeover is to reshape RNA fate in the cell to modulate host gene expression and evade immune responses. Here we provide an extensive review of work in this area, particularly how the host-viral interplay influences RBP functions to modulate the host cell. Overall, in this review, we highlight the myriad of ways RBPs can regulate RNA stability in either a pro-viral or antiviral manner by gathering novel insights gained from research studies in this field.

This paper proposes a new battery balancing control strategy based on state of charge (SOC) for addressing the problem of cell-to-cell differences in lithium-ion battery systems. The strategy utilizes a reconfigurable converter system to transfer energy from high-SOC battery modules to low-SOC battery modules and allows balancing the battery modules while they are powering the load. A MATLAB/Simulink simulation model with five batteries was built to validate the effectiveness of the proposed balancing strategy under unloaded and loaded conditions. The simulation results demonstrate that the proposed strategy achieves more efficient and accurate battery module balancing compared to the previous balancing modes, thus increasing the overall lifespan and safety of the battery pack.

This paper experimentally reveals some of the resources offered by the evolution of the instantaneous active electric power in describing the state of three-phase AC induction asynchronous electric motors (with squirrel-cage rotor) operating under no-load conditions. A mechanical power is required to rotate the rotor at no-load and this mechanical power is satisfactorily reflected in the constant and variable part of instantaneous active electric power. The variable part of this electrical power should necessarily have a periodic component with the same period as the period of rotation of the rotor. The paper proposes a procedure for extracting this periodic component description (as a pattern, by means of a selective averaging of instantaneous active electrical power) and analysis. The time origin of this pattern is defined by the time of a selected first passage through the origin of an angular marker placed on the rotor, detectable by a proximity sensor (e.g. a laser sensor). The usefulness of the pattern in describing the state of the motor rotor has been demonstrated by several simple experiments which show that a slight change in the no-load running conditions of the motor (e.g. by placing a dynamically unbalanced mass on the rotor) has clear effects in changing the shape of the pattern.

Power Electronic development determines introduction of nonlinear devices in Electric Power Systems. Introduction of nonlinear devices increase current harmonics in Transmission and Distribution Power Systems. Distribution transformers and feeders increase power losses and their nominal parameters are reduced. Present work introduces a procedure to evaluate maximum permissible load in single phase distribution transformers with massive introduction of a new type of nonlinear load which changes daily demand graphs.

Authors evaluated the relevant literature related to the purging which is the interaction between selection and inbreeding where the population may get rid of its inbreeding load at least partially. The backroad of the relevant theory was given and the available methods were described both based on the conventional quantitative genetic approach (based on genealogy data) and based on the latest genomic methods. The different parameters necessary for signalling purging (highlighting those inbreeding coefficients which are not yet been widely known in animal and veterinary science) were presented together with the relevant results of the literature. The available statistical methods together with the softwares and R packages to calculate various inbreeding coefficients and to determine inbreeding depression and purging were provided. The main results of the different approaches obtained in laboratory ZOO and domesticated populations (lethal equivalents, ancestral inbreeding, Inbreeding-Purging Model, genomic approaches) were summarized and presented. Application possibilities and future prospective of purging was also discussed.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

The variation of mutual inductance and load parameters will affect the transmission power and efficiency of the inductive power transfer (IPT) system. The identification of mutual inductance and load parameters is an essential part of establishing a stable and reliable IPT system. This paper presents a joint identification method of load and mutual inductance for LCC-S IPT system, which does not require the establishment of primary and secondary communication and related control. Firstly, the resistance-inductance characteristics of the equivalent load of the rectifier are analyzed by simulation, and then the rectifier and system load are equivalent to the circuit model of resistance and inductance in series. Secondly, the characteristics of the reflected impedance are analyzed, and the functional relationship between the transmitter impedance and the rectifier impedance is established by using the ratio of the real part to the imaginary part of the reflected impedance, which realizes the decoupling of the load and the mutual inductance. Thirdly, the functional relationship between the equivalent impedance of the rectifier and the load resistance of the system is obtained by data fitting. Then, the equations of the above two functional relationships are combined. By measuring the voltage of the parallel compensation capacitor at the transmitting side, the current of the transmitting coil and the phase difference between the two, the battery load can be solved first, and then the mutual inductance can be calculated, so that the high-precision identification of the load and mutual inductance can be realized. Finally, an experimental platform of LCC-S IPT system is built for experimental verification. The experimental results show that the maximum identification errors of mutual inductance and load are 5.20 % and 5.53 %, respectively, which proves that the proposed identification method can achieve high precision identification.

Voltage Source Inverters (VSI) are the integral part of Electrical Vehicles (EV) to enhance the reliability of supply power to critical loads in vehicle to load (V2L) applications. Inherent properties of sliding mode control (SMC) makes it one of the best vailable options to achieve desired voltage quality under variable load conditions. Intrinsic characteristic of robustness associated with SMC is achieved generally at the cost of unwanted chattering along the sliding surface. To manage this compromise better, optimal selection of sliding surface coefficient is applied with proposed composite exponential reaching law (C-ERL). The novelty of proposed C-ERL is associated with the intelligent mix of exponential, power and difference functions blended with rotating sliding surface selection (RSS) technique for three phase two level VSI. Moreover, proposed reaching law along with power rate exponential reaching law(PRERL), enhanced exponential reaching law(EERL) and repeatitive reaching law(RRL) are implemented on two level three phase VSI under variable load condtions. Comparative analysis of which strongly advocates the authenticity and effectiveness of proposed reaching law in achieving well regulated output voltage, with high level of robustness, reduced chattering and low %THD.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Passive balancing is a traditional choice for lithium-ion battery packs although it is regarded as highly inefficient. One opportunity to improve traditional balancing in sub-medium size battery packs is to combine two balancing methods: passive and active. Statistical analysis have been performed to rationalize battery pack division in smaller packs and use of higher level selective charging method to decrease losses of passive balancing. An experimental balancing prototype have been designed and tested for efficiency. Results indicate energy performance degradation if cells of the pack are with low capacity variation. Proposed balancing approach could improve performance under high cell mismatch conditions.

This article presents a review of resources for batteries with a specific focus on sustainability aspects related to raw materials, electrode and electrolyte chemistries suitable for the automobile industry. We emphasize the importance of prioritizing sustainability in battery technology evolution, which is expected to shift towards earth-abundant materials. One notable advancement in this direction is the utilization of glass solid-state electrolytes, known for their high ionic conductivity, low electronic conductivity, and high dielectric constant. However, our review suggests that further research should explore synthesis methods to modify anisotropic properties, enhancing the performance of solid-state electrolytes, particularly in facilitating the flow of ions.

This study investigates the relationship between energy metals and precious metals to assess their suitability as safe haven assets in clean energy investment portfolios. It focuses on the impact of events in 2020 and 2022, characterized by substantial investments in clean energy. The research reveals that, except for Nickel Futures (NICKELc1), energy metals are positively linked with clean energy indexes. This suggests that they can serve as a secure investment option for green investors looking to diversify their portfolios. As a result, the study dismisses the initial question, indicating that energy metals can indeed be considered safe havens within the context of clean energy investments. Additionally, the research reinforces prior findings that precious metals like gold, silver, and platinum possess safe haven characteristics in relation to specific clean energy stock indexes. These results have significant implications, particularly given the increasing investments in clean energy stocks and the recurring uncertainties in the market. In summary, this study supports the idea that both energy metals and precious metals can play valuable roles in clean energy portfolios, providing stability during turbulent times in the market.

Electric vehicles (EVs) will have a greater need for the amount of electricity needed to charge them as their popularity grows. It is anticipated that in order to accomplish this objective, it will be essential to implement a variety of solutions for grid transportation that are designed to complement one another and to make significant changes to the transmission infrastructure. It is possible to reduce the amount of energy that is lost on the power network through strategic planning and control, which may include economic models and methods to engage and reward users. This would eliminate the need for grid upgrades. Charging electric vehicles can also assist alleviate problems with transmission systems that are caused by the allocation of electric vehicles (EVs) using bidirectional charging method. The most significant problems that can occur with a transmission network are power loss and unstable voltage. Adding EV units to the transmission network is typically an effective method for resolving these challenges. As a result, EVs need to have the appropriate arrangement and dimensions. This research establishes where and how many electric vehicles (EVs) should be in a radial transmission network both before and after the adjustment is made. An artificially intelligent (AI) approach, known as a hybrid genetic algorithm particle swarm optimization (HGAIPSO), is used both before and after the radial network modification to find the optimal EV location and size. When electric vehicles are coordinated in an active transmission network, power losses are decreased, voltage profiles are raised, and system stability is increased. These benefits can be attributed to the greater use of electric vehicles. The simulation found that incorporating EVs into the testing system resulted in a considerable decrease in the quantity of power that was wasted. The minimal bus voltage of the system also undergoes similar kinds of enhancements. According to the findings of the comparative study, the proposed method mitigates both the voltage fluctuations and the power losses that occur in the transmission system. For type 1, type 2, and type 3 EV allocations, the IEEE-30 bus test system reduced real power loss by 40.70%, 36.24%, and 42.94%, respectively. IEEE-30 bus voltage reaches 1.01 pu.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

The BH 25 railway bridge, located in Indonesia, consists of three spans: 9.5 m (span-1 girder type), 21.9 m (span-2 truss type), and 9.6 m (span-3 girder type). Despite the initial plan for camber, it was not achieved, leading to the installation of temporary support on span-2. To assess the level of damage and determine the necessary steps, static and dynamic tests were conducted using a CC206 locomotive. The maximum deflection was recorded at -4.60 mm for span-1, -11.30 mm for span-2, and -3.42 mm for span-3. The dominant frequency in the vertical direction of span-2 was found to be 14.65 Hz. Due to the inability to achieve the planned camber and the subsequent removal of temporary support, external prestressing will be implemented, resulting in a camber of 11.82 mm. This change in prestressing also affects the dominant frequency of span-2, which becomes 17.07 Hz.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

Incorporating AI tools like ChatGPT into higher educational settings has been beneficial for education, yet the extent of user satisfaction with the information provided by these tools, known as user information satisfaction (UIS), remains underexplored. Our study introduces a UIS model specifically designed for ChatGPT's application in the educational sector. Drawing from established UIS theory, we crafted a model centered around seven essential factors that influence the effective use of ChatGPT, aiming to guide both educators and learners in overcoming common challenges such as plagiarism and ensuring the ethical use of AI. We gathered data from Indonesian university participants and applied Structural Equation Modeling using Smart-PLS 4.0 for our data analysis. The results reveal that completeness, precision, timeliness, convenience, and the format of information as the most influential factors driving user satisfaction with ChatGPT. Interestingly, our research indicated that the accuracy and reliability of the information, typically deemed paramount, were not the primary concerns in the academic use of ChatGPT. Our findings lead to a recommendation for a cautious approach to the integration of ChatGPT in higher education. We advocate for a strategic use that recognizes its innovative potential while also acknowledging its limitations, thus ensuring a responsible and effective application in educational contexts. This balanced perspective is crucial for integrating AI tools into the academic fabric without compromising educational integrity or quality.

This paper explores the challenges and opportunities of balancing cultural preservation and tourism investment in historic Syrian cities in the post-war period. The Syrian conflict has caused significant damage to the country's cultural heritage, including its ancient cities, which are UNESCO World Heritage sites. Key issues raised include what challenges local governments to face, the impact of the war on the preservation of historic sites, how tourism can be used as a tool for economic development, and how to ensure that cultural heritage is preserved while also allowing for tourism investment. To gain an in-depth understanding of the old Syrian cities, extensive research has been conducted, including a review of existing literature and interviews with key stakeholders. The researcher found that rebuilding historic Syrian cities is a complex task that requires balancing cultural preservation with tourism investment. It will require collaboration between government officials, preservationists, developers, and local communities to ensure that these cities are restored in a way that respects their history and culture while also promoting economic growth through tourism.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

We provide a comprehensive framework for forecasting five minute load using Gaussian processes with a positive definite kernel specifically designed for load forecasts. Gaussian processes are probabilistic, enabling us to draw samples from a posterior distribution and provide rigorous uncertainty estimates to complement the point forecast, an important benefit for forecast consumers. As part of the modeling process, we discuss various methods for dimension reduction and explore their use in effectively incorporating weather data to the load forecast. We provide guidance for every step of the modeling process, from model construction through optimization and model combination. We provide results on data from the PJMISO for various periods in 2018. The process is transparent, mathematically motivated, and reproducible. The resulting model provides a probability density of five-minute forecasts for 24 hours.

Although migraine belongs to the main causes of disability worldwide the mechanisms of its pathogenesis are poorly known, which is among the reasons that this disease is underdiagnosed and undertreated. As migraine diagnosis is based on the subjective assessment of symptoms, there is a need to establish objective markers of its occurrence and severity. Tryptophan (TRP) metabolism has been associated with the pathogenesis of neurological and psychiatric disorders. In the present work, we investigated an association between migraine and the urine concentration of TRP and its metabolites 5-hydroxyindoleacetic acid (5-HIAA), kynurenine (KYN), kynurenic acid (KYNA) and quinolinic acid (QA) in 21 low-frequency episodic migraine patients and 32 controls. Migraine patients displayed lower urinary levels of 5-HIAA and KYNA, but KYN and QA were enhanced as compared with the controls. Consequently, the patients were characterized by different values of the 5-HIAA/TRP, KYN/TRP, KYNA/KYN, and KYNA/QA ratios. Furthermore, urinary concentration of 5-HIAA was negatively correlated with Migraine Disability Assessment score, monthly migraine, and monthly headache days. A negative correlation between Patient Health Questionnaire 9 scores assessing depression. In conclusion, the urinary 5-HIAA level may be an easy-to-determine marker of migraine occurrence and severity and may contribute to the identification of migraine patients with depression.

This study explores individual and contextual risk factors for the onset of work interfering with private life (WIL) and private life interfering with work (LIW) among self-employed men and women across European countries. It also studies the relationship between interference (LIW and WIL) and wellbeing among self-employed men and women and the effect of macro level risk factors. Data from the fifth round of European Working Conditions Survey was utilized and a sample of self-employed men and women with active businesses was extracted. Applying multilevel regressions, results show that though business characteristics are important for level of WIL, time demand is the most evident risk factor for WIL and LIW. There is a relationship between wellbeing and WIL and LIW respectively, and time demands is the most important factor in this relationship. Gender equality on the labor market did not relate to level of interference, nor did it mediate the relationship between interference and wellbeing. However, the main and most important risk factor for experiencing WIL and LIW and for how interference relate to wellbeing is gender relation processes in work and life, both on individual and contextual level.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

AbstractThe escalating impact of artificial intelligence (AI) has birthed the fascinating technology of deepfakes, capable of meticulously crafting hyper-realistic audio-visual manipulations. Within the realm of healthcare, this technology presents a double-edged sword, brimming with potential for revolutionizing various facets of care delivery while simultaneously harboring significant ethical and practical challenges. This research delves into the complex narrative surrounding AI deepfakes in healthcare, meticulously analyzing both the exciting opportunities they offer, and the inherent risks associated with their implementation.Background:Traditional healthcare practices face limitations in patient engagement, accessibility, and training efficacy. Deepfakes, with their ability to simulate real-world scenarios and interactions, emerge as a potential solution, offering personalized patient education, immersive mental health interventions, remote consultations with virtual avatars, and realistic training simulations for medical professionals.Objective:This research aims to comprehensively understand the multifaceted impact of AI deepfakes in healthcare systems. It seeks to: Identify and analyze the potential benefits of deepfakes in specific healthcare applications. Assess the ethical and practical challenges associated with deepfake implementation in healthcare settings. Propose recommendations for safe, responsible, and ethical integration of deepfakes within the healthcare system.Results/Conclusion:The research findings illuminate a landscape replete with opportunities and challenges. Deepfakes offer the potential to enhance patient education, personalize mental health interventions, facilitate remote consultations, and revolutionize medical training. However, concerns regarding misinformation, ethical breaches, data privacy, and technical limitations pose significant challenges.The conclusion emphasizes the need for a balanced approach that capitalizes on the innovative potential of deepfakes while mitigating potential harm. Collaborative efforts involving healthcare professionals, technologists, and policymakers are crucial for establishing ethical frameworks, ensuring responsible development, and harnessing the positive power of deepfakes to build a future where healthcare benefits from cutting-edge technology while prioritizing patient well-being and ethical principles.

Finnish government's carbon neutrality goal by 2035 requires integration of renewable energy sources into the power grid. Considering the stochasticity of these resources, additional sources of flexibility are necessary to balance supply and demand in the power grid. District heating network (DHN) operators in Finland plan to shut down fossil-fuel-based combined heat and power plants and electrify heating systems by deploying heat pumps (HPs) and electric boilers. Techno-economic analysis and optimal operation of DHN-connected HPs and electric boilers in providing ancillary balancing services considering the 15-minute granularity in the balancing markets in Finland were investigated. The objective was to maximize the potential revenue for DHN operators gained from the day-ahead electricity market and frequency containment reserve (FCR) balancing markets. Three inter-connected DHNs in the Helsinki metropolitan area were optimized considering the reference year 2019 and each operator's decarbonization strategies for 2025. HPs could gain the highest profit from FCR-D up-regulation market, while the electric boiler may gain considerable profits from FCR-D down-regulation market. Compared to other balancing markets studied, the FCR-N market had a limited profit margin. Sensitivity analysis indicated that spot electricity prices and CO2 emission allowance prices have a significant impact on the profit from balancing markets.

Drag-dominant tidal turbine energy holds tremendous clean energy potential but faces significant hurdles as unsuitability of Disk Actuator theory due to the varying swept blockage area, unaccounted bypass flow downstream interaction and rotor parasitic drag whereas Blade Element Momentum theory is computably effective for majorly 3-blade lift-dominated aerofoil. This study proposes a novel method to find the optimal TSR of any turbine with a cost-effective and user-friendly Moment Balancing algorithm to support robust tidal energy development. Performance analysis CFD study of Pinwheel and Savonius tidal turbines was carried out. Dynamic TSR matrix was developed with varying rotational speeds and fluid velocities for reliability, unlike previous works simulated at a fixed fluid velocity. Novel parameters such as thrust and idle moment are introduced as functions of only inlet fluid velocity and rotational speed respectively. These relationships are verified through regression analysis, and the turbines' net moment equations are established based on these parameters. Rotational speed was a reliable predictor for Pinwheel's idle moment, while inlet velocity was a reliable predictor for thrust moment in both models. The optimal (Cp, TSR) values for Pinwheel and Savonius turbines were (2.37, 0.223) and (0.63, 0.16) respectively, within an acceptable error range for experimental validation.

This study is designed to assess and improve apparel sewing section efficiency and productivity throughout line balancing. Apparel industry is one of the oldest and among the most global industry, being primarily concerned with the design and production of cloth and their supply. The central process in apparel manufacturing is the joining together of components which is known as the sewing process , which is the most labour intensive type of manufacturing process .Proper utilization of resources in garment sewing section is more critical to enhance the performance of the apparel industry by reducing production cost and minimizing wastage. For effective utilization of resources in the sewing section, good line balancing is important to increase productivity and production efficiency. This research was a design to analyse and improve the assembling line in the case of Telaje garment manufacturing and sales plc. The study was first conduct observations in the production floor and start work with the selection of sewing line in the garment production process. Among the nine lines of the factory select one on the production floor and one garment ordered product known as five pocket men’s jeans trousers are selected. For this study, both qualitative and quantitative research approaches were employed. Both primary and secondary data sources are used to detail the collected relevant data to understand the current efficiency scenario of the factory. The main challenges to minimizing line efficiency and productivity with the expected performance measurement are improper utilization of resources and improper implementation of line balancing in sewing section, therefore this thesis work shows that the bottleneck process and consequence solution will be searched, and finally significantly improving the productivity by 418 unit products/ day and, hence the efficiency will increase from 28.83% to 50.04% of the line

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

As rotary machines have become more complicated, balancing processes have been classified as a vital step in condition monitoring to ensure machines operate both reliably and safely. This is especially important for flexible machines which normally work at rotations speeds above critical limits. Imbalance is a common problem in flexible rotating machinery that can lead to extreme vibration and noise levels. This is one of the major reasons for studying various balancing methods applied to the vibration response of rotating machines. Recently, the relation between acoustic and vibration response during a rotary machine balancing process based on the Four-Run method has been presented for constant speed machines. This method cannot be applied to machines in start-up or shut-off. Hence, by considering the acoustic and vibration responses of a machine between its critical speeds, this research presents a new innovative speed-variant balancing method based on the original Four-Run method, named as "Peak to Peak for Critical Speeds (PPCS)". The proposed method consists of two major types of application: the first is in the Run-up of the machine and the second is in Shut-down. Experimental laboratory results show that the PPCS method can be implemented for speed-variant and flexible rotary machines during run-up or shut-down transient processes based on acoustic and vibration measurements. As a phase-less and a contactless method, the PPCS can be employed as an innovative and readily available method for condition monitoring in the future.

Highly-skilled migrants and refugees finding employment in low-skill vocations, despite professional qualifications and educational background, has become a global tendency, mainly due to the language barrier. Employment prospects for displaced communities are mostly decided by their knowledge of the sublanguage of the vocational domain they are interested in working. Common vocational domains include agriculture, cooking, crafting, construction, and hospitality. The increasing amount of user-generated content in wikis and social networks provides a valuable source of data for data mining, Natural Language Processing and machine learning applications. This paper extends the contribution of the authors’ previous research on automatic vocational domain identification by further analyzing the results of the machine learning experiments with the domain-specific textual data set, considering 2 research directions: a. predictions analysis and b. data balancing. Wrong predictions analysis and the features that contributed to misclassification, along with correct predictions analysis and the features that were the most dominant, contributed to the identification of a primary set of terms for the vocational domains. Data balancing techniques were applied on the data set to observe their impact on the performance of the classification model. A novel 4-step methodology is proposed in this paper for the first time, consisting of successive applications of SMOTE oversampling on imbalanced data. Data oversampling obtains better results than data undersampling in imbalanced data sets, while hybrid approaches perform reasonably well.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Plantar flexors (PF) spasticity is known to poorly correlate with active dorsiflexion (DF) impairment throughout the swing phase of hemiparetic gait. Spastic Cocontraction, instead, stemming from descending pathways, potentially misdirect antagonist PF activity opposing DF during swing. Electromyographic (EMG) recordings, while unable to differentiate between reflex-based and descending origins, may offer valuable insights into this distinction by exploring PF EMG activity after tibial nerve neurotomy (which eliminates PF spasticity). Eleven subjects with hemiparesis walking at comfortable velocity and 11 controls walking at comfortable and slow velocity, underwent kinematic and PF/DF EMG analysis. Five of the hemiparetic subjects underwent tibial neurotomy &gt;1 year prior. We evaluated spasticity at rest (Tardieu scale), maximal ankle dorsiflexion, tibialis anterior agonist recruitment and gastrocnemius medialis and soleus cocontraction coefficients during swing. At slow velocity, controls (0.80±0.12 m/s) moved at a similar pace as hemiparetic subjects (0.73±0.37 m/s, NS). Hemiparetic subjects showed: (i) reduced ankle DF across swing (ii) increased PF cocontraction, including before any DF (iii) higher cocontraction despite absent spasticity in tibial neurotomy subjects (iv) higher tibialis anterior recruitment. Increased PF cocontraction occurs in the absence of spasticity or ankle DF despite higher agonist recruitment. Spastic cocontraction is a major factor limiting active DF at swing, unlike spasticity.

Upon inbreeding, the architecture of the inbreeding load shifts as selection purges strongly deleterious recessive mutations and drift fixes many milder ones. Most small inbred populations show limited genetic variation while crosses between such populations commonly express pronounced heterosis, confirming fixation. In contrast, purging appears to be limited in that inbred populations often retain substantial inbreeding depression. In addition we have the enigma Darwin noted: purely selfing taxa are unknown. Because both purging and fixation reduce inbreeding depression and load, another mechanism must exist to sustain these. Background selection and the associations that develop among alleles in small inbred populations will shift the architecture of the load potentially creating blocks of recessive mutations linked in repulsion. This would generate pseudo-overdominance that could sustain these “PODs” and inbreeding load. Recombination and crosses between lineages could erode PODs. Crosses between populations fixed for different mutations would generate high pseudo-overdominance, enhancing heterosis and potentially POD formation. New recessive mutations arising within PODs would reinforce overdominance. PODs should generate clear genetic signatures including genomic hotspots of heterozygosity and linkage disequilibrium containing alleles at intermediate frequency generating segregating load. Results from several simulation and empirical studies match these predictions. Further simulations and comparative genomic analyses are needed to rigorously test whether PODs exist in sufficient strength and number to generate persistent inbreeding depression and load in inbred lineages.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

Towards smart batteries for electric vehicles (EVs) smart algorithms to control battery packs, mainly reconfigurable batteries, have to be developed. This work proposes a reinforcement learning (RL) algorithm to balance the State of Charge (SoC) of reconfigurable batteries based on the topologies half-bridge and battery modular multilevel management (BM3). As RL algorithm, Amortized Q-learning (AQL) is implemented, which allows enourmous numbers of possible configurations of the reconfigurable battery to be controlled, as well as the combination of classical controlling approach and machine learning methods. This enables safety mechanisms in control. As a neural network of the AQL a Feedforward Neuronal Network (FNN) is implemented consisting of three hidden layers. The experimental evaluation using a 12-cell hybrid cascaded multilevel converter illustrates the applicability of the method to balance the SoC and maintain the balanced state during discharge. The evaluation shows a 20.3% slower balancing compared to the classical. Nevertheless, AQL shows great potential to be applied for multiobjective optimizations as an applicable RL algorithm for control in power electronics.

The IDS serves as a security system that maintains constant surveillance over network traffic and host systems in order to identify any security breaches or potentially concerning activities. Recently. the rise in cyber-attacks has driven the necessity for the development of automated and intelligent network intrusion detection systems. These systems are designed to learn the typical patterns of network traffic, allowing them to identify any deviations from normal behaviour, which can be classified as anomalous or malicious. Machine learning methods are widely used to exhibit a satisfactory effectiveness in detecting malicious payloads in the network traffic. While the volume of the data generated from IDS is increasing exponentially results in the emergence of substantial security risks, it highlighted the imperative to strengthen network security. The performance of traditional machine learning methods depends on the dataset and the data balance distribution in it. while most of IDS datasets suffer from unbalancing, this limits the performance of the machine learning method used in the system and results in missed detections and false alarms in the conventional IDSs. To address this issue, this paper presents a new model-based Generative Adversarial Network (GAN) called TDCGAN to enhance the detection rate of less of minor class in the dataset while maintaining efficiency. The proposed model consists of one generator and three discriminators with an election layer at the end of architecture. The UGR’16 data set is used for evaluation purposes. In order to demonstrate the efficacy of our proposed model, various machine learning algorithms have been utilized for comparison. The experimental findings have determined that TDCGAN presents an efficient resolution for addressing imbalanced intrusion detection and surpasses the performance of other oversampling machine learning methods.

In modern inverter applications, multilevel converters are used thanks to their capability of reducing the passive fi lter volumes, improving the overall THD, sharing the power sources across the several converter cells, and providing a reconfi guration ability in case of failure. However, increasing the number of cells makes more complex the control of the converter. This article proposes a decentralized control technique based on the use of elementary modular controllers, associated with each converter cell and communicating with their close neighbors to obtain the balancing of the powers they supplied. Each modular controller can be dynamically removed or added to allow reconfi guration of the converter for functional safety purpose. This method is applied to a 240V/3A 5-cells Cascaded Full-Bridge Multilevel Converter. The response of the system to load transients and cell voltage disturbances demonstrates the robustness of the proposed decentralized control method. Thanks to the use of modular controllers, the number of levels of the converter can be extended to the order N without adding complexity to its control.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Tourism carrying capacity remains pivotal for ensuring sustainable development within protected terrains, accentuating the balance between conservation, socio-economic benefits, and visitor satisfaction. This study delves into the intricate dimensions of this balance, focusing on the Katon-Karagay National Park (KKNP). Merging comprehensive empirical data accrued from fieldwork within the park, calculations surrounding recreational loads, and a synthesis of relevant literature, the study designed a methodology. This included calculated techniques incorporating ecological and tourist social capacities, the psychocomfort approach, and an ongoing monitoring approach, supplemented by exclusive data from the park's administration. Key findings underscored the significance of an adaptive balance, revealing specific permissible recreational loads for different park zones. For instance, zones of quiet recreation evidenced up to 5 people/ha, while active recreation zones fluctuated between 20 to 100 people/ha. Monitoring evidenced critical environmental changes, shaping recommendations for effective tourism flow regulation, ensuring alignment with established norms and ecological preservation. The exploration substantiates the indispensability of a meticulously structured approach to ascertain tourism carrying capacity, emphasizing the harmony achievable between environmental sanctity and human pursuits. KKNP's empirical data serves as a paradigm, guiding sustainable tourism frameworks for similar ecologically sensitive regions.

Robot Operating System 2 (ROS 2) is a robotic software that uses a set of Quality of Service (QoS) policies to manage the quality of robot data transmissions in a network, such as the RELIABLE and KEEP_LAST options. In ROS 2 node communication, the RELIABLE connection guarantees that all message data can be properly sent from the publisher to the subscriber. However, strict reliability is not guaranteed if the RELIABLE connection uses the KEEP_LAST option to transmit the robot data in the publish-subscribe communication. This study aims to analyze the efficiency of local cache, cache control, and QoS balancing optimization to improve ROS 2 node communication when using the RELIABLE and KEEP_LAST options to transmit multi-robot data in Aggregated Robot Processing (ARP) architecture. Our idea in local cache and cache control is to streamline the sensor data output before processing it when the sensor device produces the data with the same value in a row. Furthermore, QoS balancing optimization aims to balance the DEPTH and DEADLINE QoS configuration to determine the rates and buffer size in ROS 2 node communication. This study shows that combining local cache and QoS balancing optimization improves multi-robot data transmission and cooperation in ARP architecture.

Electricity demand forecasting has been a real challenge for power system scheduling in the different levels of the energy sectors. Various computational intelligence techniques and methodologies have been employed in the electricity market for load forecasting; although, scant evidence is available about the feasibility of each of these methods considering the type of data and other potential factors. This work introduces several scientific, technical rationale behind intelligent forecasting methods, based on the work of previous researchers in the field of energy. The fundamental benefits and main drawbacks of the aforementioned methods are discussed in order to depict the efficiency of each approach in various situations. In the end, a proposed hybrid strategy is represented.

Electricity demand forecasting has been a real challenge for power system scheduling in the different levels of the energy sectors. Various computational intelligence techniques and methodologies have been employed in the electricity market for load forecasting; although, scant evidence is available about the feasibility of each of these methods considering the type of data and other potential factors. This work introduces several scientific, technical rationale behind intelligent forecasting methods, based on the work of previous researchers in the field of energy. The fundamental benefits and main drawbacks of the aforementioned methods are discussed in order to depict the efficiency of each approach in various situations. In the end, a proposed hybrid strategy is represented.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

The paper presents an extensometer designed to measure two mechanical strains at the same time—one from tensile load and the other from torsion load. Strain transducers provide different electric signals, which, after calibration, lead to the simultaneous measurement of linear (ε) and angular (γ) strains. Each of these two signals depends on the measured process and is not influenced by the other strain process. This extensometer is designed to be easily mounted on the sample with only two mounting points and can be used to measure the combined cyclical fatigue of tensile and torsional loadings. This extensometer has two bars—one rigid, reported at the resulting stress points, and one elastic and deformable. The elastic deformable bar has two beams with different orientations. When the sample is deformed, both beams are loaded by two bending moments (perpendicular to each other and both perpendicular on the longitudinal axis of the bars).

Reliable hydrological monitoring is crucial for effective water resource management, but establishing observatories in remote areas with extreme weather presents significant challenges. This study aimed at identifying cost-effective methods for streamflow estimation in such environments. We evaluated the performance of the Soil and Water Assessment Tool (SWAT) model using various precipitation data sources: ground-based rain gauge networks with different densities (one-gauge (1RG), two-gauge (2RG), and five-gauge (5RG) configurations) and satellite-derived Integrated Multi-satellite Retrievals for GPM (IMERG) data. The study focused on the Sahafihitry catchment, a 200 km² area in northeastern Madagascar. The results demonstrated that denser rain gauge networks (5RG and 2RG) captured the spatial variability of rainfall more effectively than a single gauge or IMERG data. This translated into superior SWAT model performance. Denser networks achieved higher statistical metrics (R², slope of regression a, Nash-Sutcliffe efficiency NSE, root mean square error RMSE, Kling-Gupta efficiency KGE) indicating a better fit between simulated and observed streamflow. Specifically, 5RG: R² = 0.84, a = 0.92, NSE = 0.83, RMSE = 3.33, KGE = 0.82; 2RG: R² = 0.85, a = 0.95, NSE = 0.83, RMSE = 3.36, KGE = 0.88; 1RG: R² = 0.73, a = 0.80, NSE = 0.72, RMSE = 4.28, KGE = 0.88; IMERG: R² = 0.48, a = 0.63, NSE = 0.37, RMSE = 6.46, KGE = 0.66. Furthermore, rain gauge data outperformed IMERG in simulating both flood events and low-flow periods. While IMERG offers low cost, readily available data, its lower performance introduces significant uncertainty into hydrological modeling. In contrast, the two-gauge network (2RG) achieved satisfactory streamflow simulations and represents the most cost-effective option for establishing reliable observatories within the specific characteristics of this study area.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

There are two basic methods for radial external load distribution calculation on rolling elements in a rolling element bearing: the discrete method and the integral method. Solving the discrete equilibrium quasi-static equation using the Newton-Raphson scheme, more accurate results are derived than those based on the integral method, with small theoretical and computational efforts. The Sjövall’s radial integral factors, as well as some approximations proposed in the literature, for line- and point-contacts, are revisited. Numerical approximations for the Sjövall's radial integrals are proposed. The approximations’ errors with respect to the Sjövall’s radial integral’s numerical integration are shown. The numerical results of the displacement between inner and outer rigid rings, maximum hertzian contact deflection and the most loaded element load are shown for some ball and roller bearings, for radial external load ranging from 0 to 10,000 N, and for positive, negative and zero radial clearance, solving the discrete equilibrium quasi-static equation using the Newton-Raphson method. A total of 16 figures is shown in this work, many of which are made up of sub-figures. A total of 58 figures and sub-figures is shown.

The ever-growing repertoire of genomic techniques continues to expand our understanding of true diversity and richness of prokaryotic genomes. Riboproteogenomics laid the foundation for dynamic studies of previously overlooked genomic elements. Most strikingly, bacterial genomes were revealed to harbour robust repertoires of small open reading frames (sORFs) encoding a diverse and broadly expressed range of small proteins, or sORF-encoded polypeptides (SEPs). In recent years, continuous efforts led to great improvements in annotation and characterization of such proteins, yet many challenges remain to fully understand the pervasive nature of small proteins and their impact on bacterial biology. In this work we review recent developments in the dynamic field of bacterial genome reannotation, catalogue important biological roles carried out by small proteins and identify challenges obstructing the way to full understanding of these elusive proteins.

Nowadays energy saving is a topical issue due to increasing fuel costs and this aspect is amplified by more stringent emissions regulations that impact on vehicle development. A recent study conducted by the U.S. Department of Energy shows that about five percent of the U.S. energy consumption is transmitted by fluid power equipment. Nevertheless, this study also shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications. These facts dictate a continuous strive toward improvements and more efficient solutions: to accomplish this objective a strong reduction of hydraulic losses and better control strategies of the hydraulic systems are needed. In fluid power, there exist many techniques to reduce/recover energy losses of the conventional layouts, e.g. load sensing, electrohydraulic flow matching, independent metering, etc. One of the most efficient ways to analyze these different layouts and identify the best hydraulic solution is done through virtual simulations instead of prototyping, since the latter involves higher investment costs to deliver the product into the market. However, to build a fluid power machine virtual model, some problems arise relative to different aspects, for instance: loads on actuators (both linear and rotational) are not constant and pumps are driven by a real engine whose speed depends on required torque. Furthermore, it is important to achieve higher level of detail to simulate each component in the circuit: the greater detail, the better the machine behavior is portrayed, but it obviously entails heavy impact on simulation time and computational resources. Therefore, there is a need to create mathematical model of components and systems with sufficient level of detail to easily acquire all those phenomena necessary to correctly evaluate machine performance and make modifications to the fluid power component design. In this context, a hydraulic proportional valve PVG 32 by Danfoss is taken as an object of study, its performance is analyzed with suitable mathematical model and simulation is done to observe closeness of a model to the laboratory experiment.

Nutrition and calorie intake are associated with subtle changes of thyroid function tests in subjects with intact Hypothalamic-Pituitary-Thyroid axis. Iodine deficiency and extreme fluctuations in calorie intake, such as those occurring during periods of starvation or overfeeding could lead to alterations of thyroid hormones. The dietary macronutrient composition could also influence the thyroid function. Recently, Low-Glycemic Load (LGL) diets are very popular and effective in the treatment and/or prevention of several medical conditions, including diabetes, obesity, cardiovascular disease, and epilepsy. In this review, we report the available data from the literature regarding the association between LGL diets and thyroid function or dysfunction. Unfortunately, there are only a few studies in this field, with inconsistent findings.

Abstract: Considering the significance of postural balance in shooting ability, and consequently soldiers’ occupational performance and survivability, it is of importance to promote the use of balance training programs to improve shooters' efficiency. This study explored how a balance training program affects shooting performance. Twenty participants were divided into two equal groups. They all performed 60 shots in a shooting simulator while standing. The participants went through this process twice, before and after a 4-week balance training program. The shoot-ing was done under four different conditions: without load on a stable surface, with load on a stable surface, without load on an unstable surface, and with load on an unstable surface. The training program had a significant impact on the experimental group, improving their balance by 76 ± 9% (p < 0.01). Additionally, in the experimental group, shooting score increased by 47% and the % center of gravity by 20% (p < 0.01). The stability of the shots, measured by holding time in the target, doubled from 2.2 to 4.5 seconds (p < 0.01). These improvements were more pronounced when participants had a load and/or were on an unstable surface. In conclusion, a balance training program can be beneficial for improving shooting performance.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

Grid energy storage system for PV Applications is connected with three different power sources i.e. PV Array, Battery and the Grid. It is advisable to have Isolation between these three different sources to provide safety for the equipment. The configuration proposed in this paper provides the complete isolation between the three sources. A Power Balancing Control (PBC) for this configuration is proposed to operate the system in three different modes of operation. Control of a dual active bridge (DAB) based battery charger which provides a galvanic isolation between batteries and other sources is explained briefly. Various modes of operation of a Grid energy storage system are also presented in this paper. Hardware-In-Loop (HIL) Simulation is carried out to check the performance of the system and the PBC algorithm. Power circuit (comprises of inverter, dual active bridge based battery charger, grid, PV cell, batteries, contactors and switches) is simulated and the controller hardware and user interface panel are connected as HIL with the simulated power circuit through Real Time Digital Simulator (RTDS). HIL simulation results are presented to explain the control operation, steady state performance in different modes of operation and the dynamic response of the system.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Quantum physics is intrinsically probabilistic. The entropy of a quantum state quantifies the amount of randomness (or information loss) of such state. The degrees of freedom of a quantum state are position and spin, and upon their specification Born's rule in phase space defines randomness. We focus on the spin degree of freedom and elucidate the spin entropy. Then, we present some of its properties and show how entanglement increases spin entropy. Some speculative predictions on the decay of the $Z^0,W^{+,-}$ gauge bosons conclude the paper.

Viruses have established symbiotic relationships with almost every other living organism on Earth and at all levels of biological organisation, from other viruses up to entire ecosystems. In most cases, peacefully coexisting with their hosts, but in most relevant cases, parasitising them and inducing diseases. Viruses are playing an essential role in shaping the eco-evolutionary dynamics of their hosts, and have been also involved in some of the major evolutionary innovations either by working as vectors of genetic information or by being themselves coopted by the host into their genomes. Viruses can be studied at different levels of biological organisation, from the molecular mechanisms of genome replication, gene expression and encapsidation, to global pandemics. All these levels are different and yet connected through the presence of threshold conditions allowing for the formation of a capsid, the loss of genetic information or epidemic spreading. These thresholds, as it occurs with temperatures separating phases in a liquid, define sharp qualitative types of behaviour. These {\em phase transitions} are very well known in Physics. They have been studied by means of simple, but powerful models able to capture their essential properties, allowing to understand them. Can the physics of phase transitions be an inspiration for our understanding of viral dynamics at different scales? Here we review well-known examples of transition phenomena in virology and their simplest mathematical modelling approaches. We suggest that the advantages of abstract, simplified pictures used in Physics are also the key to properly understand the origins and evolution of complexity in viruses. By means of several examples, we explore this multilevel landscape and how minimal models provide deep insights into a diverse array of problems. The relevance of these transitions in connecting dynamical patterns across levels and their evolutionary and clinical implications are outlined.

Inducer of C-Repeat Binding Factor (CBF) expression (ICE), a well-known MYC-type bHLH transcription factor, plays a crucial role in the ICE-CBF-cold regulated (COR) cold signaling pathway. Brassica rapa (B. rapa), an important oilseed and vegetable crop, exhibits strong chilling and freezing tolerance. However, the exact molecular mechanisms by which ICE1 functions in B. rapa remain unclear. Here, 41 ICE1 homologous genes were identified from six widely cultivated Brassica species using a bioinformatics approach. These genes exhibit high conservation but reveal evolutionary complexity between diploid and allotetraploid species. Low-temperature stress induced ICE1 homolog expression, with patterns differing between strong and weak cold-tolerant varieties. Two novel ICE1 paralogs, BrICE1 and BrICE2, were cloned from Longyou 6. They positively regulate cold tolerance in B. rapa via a CBF-dependent pathway, contributing to reactive oxygen species (ROS) scavenfging and osmotic adjustment. Immunoblot analysis revealed that low temperatures induce BrICE1 and BrICE2 degradation via the 26S-proteasome pathway. In summary, ICE1 exhibits complex evolutionary relationships in Brassica species. BrICE1 and BrICE2 positively regulate cold tolerance via the CBF-dependent pathway and ROS scavenging mechanism and are also responsible for balancing the development and cold defense of B. rapa.

A drug repositioning effort supported the possible use of the anti-HIV drug etravirine as a treatment for Friedreich Ataxia (FRDA). Etravirine increases frataxin protein and corrects the biochemical defects in cells derived from FRDA patients. Because of these findings, and since etravirine displays a favorable safety profile, we conducted this pilot open-label phase 2 clinical trial assessing the safety and potential efficacy of etravirine in FRDA patients. Thirty-five patients were stratified into 3 severity groups and randomized to etravirine 200 mg/day or 400 mg/day. They were treated for 4 months. Efficacy endpoints were represented by changes in peak oxygen uptake and workload as measured by incremental exercise test, SARA score, cardiac measures, measures of QoL and disability. Data were collected 4 months before the start of the treatment (T-4), at the start (T0), at the end (T4) and 4 months after the termination of the treatment (T+4). Etravirine was well tolerated. Etravirine completely stopped the progression of the SARA score during the 4-months treatment period, compared to the 4 months pre and post treatment. It increased peak workload, while the improvement of peak oxygen uptake was not statistically significant. No changes in the cardiac measures were observed. Health and QoL measures showed a worsening at the suspension of the drug. In this open trial etravirine significantly improved neurological function and was generally safe and reasonably tolerated. This suggests that etravirine represents a potential therapeutic agent in FRDA deserving testing in a randomized placebo controlled clinical trial.