Motion related human activity recognition using wearable sensors can potentially enable various useful daily applications. So far, most studies view it as a stand-alone mathematical classification problem without considering the physical nature of human motions. Consequently, they suffer from data dependencies and encounter the dimension disaster problem and the over-fitting issue, and their models are never human-readable. In this study, we start from a deep analysis on natural physical properties of human motions, and then propose a useful feature selection method to quantify each feature's classification contribution capability. On one hand, the "dimension disaster" problem can be avoid to some extent, due to the affined dimension of key features; On the other hand, over-fitting issue can be depressed since the knowledge implied in human motions are nearly invariant, which compensates the possible data inadequacy. The experiment results indicate that the proposed method performs superior to those adopted in related works, such as decision tree, k-NN, SVM, neural networks.

We propose a neural-network-based watermarking method that introduces the quantized activation function that approximates the quantization of JPEG compression. Many neural-network-based watermarking methods have been proposed. Conventional methods have acquired robustness against various attacks by introducing an attack simulation layer between the embedding network and the extraction network. The quantization process of JPEG compression was replaced by the noise addition process in the attack layer of the conventional methods. In this paper, we propose a quantized activation function that can simulate the JPEG quantization standard as it is in order to improve the robustness against the JPEG compression. Our quantized activation function consists of several hyperbolic tangent functions and is applied as an activation function for neural networks. Our network was introduced in the attack layer of ReDMark proposed by Ahmadi et al. to compare it with their method. That is, the embedding and extraction networks had the same structure. We compared the usual JPEG compressed images and the images applying the quantized activation function. The results showed that a network with quantized activation functions can approximate JPEG compression with high accuracy. We also compared the bit error rate (BER) of estimated watermarks generated by our network with those generated by ReDMark. We found that our network was able to produce estimated watermarks with lower BERs than those of ReDMark. Therefore, our network outperformed the conventional method with respect to image quality and BER.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

Abstract The value of the mass of the particles is one more mystery that current theories cannot predict, so they have to be determined experimentally. In this paper we will see how the quantization of 4D space gives rise to the quantization of mass and, in turn, the quantization of mass implies that space-time is discrete.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

Canonical quantization is a wonderful procedure for selected problems, but there are many problems for which it fails. Affine quantization is a different procedure that has shown that it can solve many problems that canonical quantization cannot. Here, words like succeed and fail refer to whether the quantization results are correct or incorrect. This paper offers two simple examples that serve to introduce affine quantization, and compare studies of two different quantization procedures. Brief comments about field theory and gravity problems undergoing quantization by affine procedures completes the paper.

Many experiments and collected data support general relativity as it explains spacetime as a smooth Riemannian manifold. However, general relativity does not explain the chaotic nature of spacetime on the quantum level, where determinism is almost impossible. This is one of the major problems in physics yet it requires a deeper theory to solve this incompatibility. In this research, a derivation made from Newton’s law of gravitation to better explain the behavior of spacetime in the quantum world with the assumption that spacetime is quantized with energy wave-particles and these wave-particles accumulate to form massive wave like particles (hence the standard model of particle physics). In the end, the derivation and the assumption together clearly illustrate general relativity and quantum theory.

In a previous work by the author it was shown that the Koopman-von Neumann formulation of classical mechanics (KvN) exhibits quantum interference. As such it was there claimed that KvN ought to be considered as a proper quantum mechanical theory in a similar sense as ordinary non-relativistic quantum mechanics (OQM) is. In this article this claim is made manifest by showing that KvN and OQM can be taken as merely inequivalent representations resulting from one and the same quantization scheme. Of course, as the typical notion of quantization necessitates the canonical commutation relations (CCR) to hold, which they do not in KvN, the concept needs to be properly revised. To justify such a revision the typical reasons for necessitation the CCR, reductionism and quantization as 'turning brackets to commutators', are examined and found insufficient.

We have shown in previous work that the equivalence of the Heisenberg and Schrödinger pictures of quantum mechanics requires the use of the Born and Jordan quantization rules. In the present work we give further evidence that the Born--Jordan rule is the correct quantization scheme for quantum mechanics. For this purpose we use correct short-time approximations to the action functional, initially due to Makri and Miller, and show that these lead to the desired quantization of the classical Hamiltonian.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

This article proposes a novel formulation of quantization, which considers the Koopman-von Neumann formulation (KvN) and ordinary non-relativistic quantum mechanics (OQM) as unitarily inequivalent representations of the same underlying structure. The approach is grounded in the notion that contextuality, rather than occurrence if Plank's constant, is the fundamental aspect of quantum mechanics. The motivation for this novel view arises from the limitations of traditional approaches to quantization, combined with previous research demonstrating contextuality in KvN. Using a representation-theoretic approach, both KvN and OQM are regarded as valid quantum theories, separated by a superselection rule.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

Affine quantization is a relatively new procedure, and it can solve many new problems. This essay reviews this new, and novel, procedure for particle problems, as well as those of fields and gravity. New quantization tools, which are extremely close to, and even constructed from, the tools of canonical quantization, are able to fully solve selected problems that using the standard canonical quantization would fail. In particular, improvements can even be found with an affine quantization of fields, as well as gravity.

A half-harmonic oscillator, which gets its name because the coordinate is strictly positive, has been quantized and determined that it was a physically correct quantization. This positive result was found using affine quantization (AQ). The main purpose of this paper is to compare results of this new quantization procedure with those of canonical quantization (CQ). Using Ashtekar-like classical variables and CQ, we quantize the same toy model. While these two quantizations lead to different results, they both would reduce to the same classical Hamiltonian if $\hbar\rightarrow0$. Since these two quantizations have differing results, only one of the quantizations can be physically correct. Two brief sections illustrate how AQ can correctly help quantum gravity and the quantization of most field theory problems.

In this paper we use Toeplitz quantization to extend in a very natural way Kostant's theorem for the group $SU(m)$ to the group of symplectomorphisms of the unit sphere and we also give another proof of the infinite dimensional version of Schur and Horn theorem for the sphere based on Schur and Horn theorem for Hermitian matrices.

In industry 4.0 era, video applications such as surveillance visual systems, video conferencing, or video broadcasting have been playing a vital role. In these applications, for manipulating and tracking objects in decoded video, the quality of decoded video should be consistent because it largely affects to the performance of the machine analysis. To cope with this problem, we propose a novel perceptual video coding (PVC) solution in which a full reference quality metric named Video Multimethod Assessment Fusion (VMAF) is employed together with a deep convolutional neural network (CNN) to obtain the consistent quality while still achieving the high compression performance. First of all, to achieve the consistent quality requirement, we propose a CNN model with an expected VMAF as input to adaptively adjust the quantization parameters (QP) for each coding block. Afterwards, to increase the compression performance, a Lagrange coefficient of Rate-Distortion optimization (RDO) mechanism is adaptively computed under Rate-QP and Quality-QP models. Experimental results show that the proposed PVC has achieved two targets simultaneously: the quality of video sequence is kept consistently with an expected quality level and the bit rate saving of the proposed method is higher than traditional video coding standards and relevant benchmark, notably with around 10% bitrate saving in average.

Covariant integral quantization with rotational symmetry SO(3) is established for the quantum motion on this group manifold, or, alternatively, for Gabor signal analysis on this group. We revisit the action of the related (non-unitary) Weyl-Gabor operator on the Hilbert space of square integrable functions on SO(3) and disclose a set of various properties. By selecting weight functions on the corresponding discrete-continuous phase space, one derives related coherent states and Wigner transform.

We apply Rosen’s approach to the quantization of the gravitational collapse in the simple case of a pressureless “star of dust” and we find the gravitational potential, the Schroedinger equation and the solution for the collapse’s energy levels without any approximation. By applying the constrains for a black hole (BH), we found the analogous quantum quantities and the BH mass spectrum, again without any approximation. Remarkably, such a mass spectrum is the same which was found by Beken- stein in 1974. Finally, our approach permits to find the exact quantum representation of the Schwarzschild BH ground state at the Planck scale.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

Novel approaches under the extreme conditions of ultra-high gravity of a super massive black hole allow us to assume that the spacetime degrades into the single dimension of time. A unique interpretation of the non-relativistic Schrödinger equation together with the relativistic Klein-Gordon and Dirac equations is presented by swapping the three dimensional space derivatives with the singular time derivative in the D’Alembertian operator. This apparatus reveals a unique time dependent wave equation that results in some implications such as possible time quantization with the intervals of around 3.36 × 10−21 ? which is in the order of uncertainty in time, ∆? = 1.3 × 10−21 ?, calculated from the energy-time version of the Heisenberg uncertainty principle for electrons. As a result of this, an antisymmetric wave function around the edge of the event-horizon zone appears and indicates that the virtual particle-antiparticle pairs of the electron field split into two real components with the spin-up and down states, reconfirming the Hawking radiation. Energy eigenvalues calculated from the application of the Dirac equation satisfies the preservation of energy and charge. The wave equation invoked in this study reduces into the time dependent Dirac equation within the neighborhood of zero-point, ? = 0, insuring the relevance of the evaluations.

When it comes to financial transactions and counterfeit detection systems, banknote classification is crucial. In this paper, we propose an approach for the classification of Kazakhstan banknote images integrating Learning Vector Quantization (LVQ) with Statistical Texture Feature Extraction using the Gray Level Co-occurrence matrix (GLCM). Our methodology demonstrates effectiveness in accurately classifying banknote images, as evidenced by experimental results. The comprehensive testing scenarios show promising outcomes, with the combination of GLCM and Color Histogram under the LVQ algorithm achieving a high accuracy of 94.87 percent at distance 1 and 90°. These findings indicate the robustness and practical viability of the proposed method for authenticating banknotes.

Post-training quantization is pivotal in deploying convolutional neural networks for mobile applications. Block-wise reconstruction with adaptive rounding, as employed in prior works like BrecQ and Qdrop, facilitates acceptable 4-bit quantization accuracy. However, adaptive rounding is time-intensive, and its constraint on weight optimization space curtails the potential for quantization performance. The optimality of block-wise reconstruction hinges on the quantization status of subsequent network blocks. In this investigation, we delve into the theoretical underpinnings of the limitations inherent in adaptive rounding and block-wise reconstruction. Our exploration leads to the development of a post-training quantization methodology, designated as AE-Qdrop. This algorithm operates in two distinct phases: block-wise reconstruction and global fine-tuning. The block-wise reconstruction phase introduces a progressive optimization strategy, superseding adaptive rounding, which not only augments quantization precision but also significantly improves quantization efficiency. To mitigate the risk of overfitting, we introduce a random weighted quantized activation mechanism. During the global fine-tuning phase, we account for interdependencies among quantized network blocks. The weight of each network block will be corrected with logit matching and feature matching. Extensive experiments validate that AE-Qdrop achieves high-precision and efficient quantization. For instance, in the case of 2-bit MobileNetV2, AE-Qdrop outperforms Qdrop by achieving a 6.26% enhancement in quantization accuracy and quintupling the quantization efficiency.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

If "quantization is an art" then it can be greatly rened by adopting cyclic time formalism. In past papers we have proven the effectiveness of a formulation of physics based on cyclic relativistic time. Now we can demonstrate in a general way, by using theorems of Geometric Quantization, that the Poisson brackets of intrinsically cyclic time dynamics directly imply the ordinary canonical commutation relations and the other Dirac's rules of canonical Quantum Mechanics. In other words, according to our result, canonical quantization is an implicit way of imposing intrinsically cyclic time dynamics without explicitly saying that time is a cyclic dimension.

Cosmic inflation has presented solutions for a number of important cosmological problems, yet left some unanswered. In this paper, we present a cosmological model based on the quantization of the zero-point field which is consistent with empirical data, requires fewer assumptions, and presents answers to some of those unanswered questions. A comparison between standard cosmology and the theory presented in this paper is given below. Vacuum energy density: Standard inflationary model needs both Hubble’s constant and Matter density to estimate it. But, new cosmological model needs only Hubble’s constant. Non-vacuum energy density: Standard model can’t predict it. But, the new model can predict using only Hubble’s constant. Ratio of vacuum energy to total energy: Standard model can’t predict it. But, new model can predict it, that too without using Hubble’s constant. Energy conservation: In standard model, total energy is not conserved before inflation. But, in the new model, energy is conserved right from beginning of the universe whose net energy (including gravitational potential energy) is always zero. Flatness and homogeneity: Standard model needs Inflaton field with a specific potential energy distribution to explain it. But, new model doesn’t need any such hypothetical field, just the zero-point field is sufficient. Based on the new cosmological model, in the conclusion, realistic possibility for existence of multiverse and a mechanism for end of universe are discussed.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Although migraine belongs to the main causes of disability worldwide the mechanisms of its pathogenesis are poorly known, which is among the reasons that this disease is underdiagnosed and undertreated. As migraine diagnosis is based on the subjective assessment of symptoms, there is a need to establish objective markers of its occurrence and severity. Tryptophan (TRP) metabolism has been associated with the pathogenesis of neurological and psychiatric disorders. In the present work, we investigated an association between migraine and the urine concentration of TRP and its metabolites 5-hydroxyindoleacetic acid (5-HIAA), kynurenine (KYN), kynurenic acid (KYNA) and quinolinic acid (QA) in 21 low-frequency episodic migraine patients and 32 controls. Migraine patients displayed lower urinary levels of 5-HIAA and KYNA, but KYN and QA were enhanced as compared with the controls. Consequently, the patients were characterized by different values of the 5-HIAA/TRP, KYN/TRP, KYNA/KYN, and KYNA/QA ratios. Furthermore, urinary concentration of 5-HIAA was negatively correlated with Migraine Disability Assessment score, monthly migraine, and monthly headache days. A negative correlation between Patient Health Questionnaire 9 scores assessing depression. In conclusion, the urinary 5-HIAA level may be an easy-to-determine marker of migraine occurrence and severity and may contribute to the identification of migraine patients with depression.

Background: Functional Movement Screening (FMS) allows for rapid assessment of an individual’s physical activity level and timely detection of sports injury risk. However, traditional functional movement screening often requires on-site assessment by experts, which is time-consuming and prone to subjective bias. Therefore, the study of automated functional movement screening has become increasingly important. Methods: In this study, we propose an automated assessment method for FMS based on the improved Gaussian Mixture Model (GMM). First, the oversampling of minority samples is conducted, the movement features are manually extracted from the FMS dataset collected with two Azure Kinect depth sensors, then we train the Gaussian mixture model with different scores (1 point, 2 points, 3 points) of feature data separately, finally, we conducted FMS assessment by the Maximum Likelihood estimation. Results: The improved GMM has a higher scoring accuracy (Improved GMM:0.8) compared to other models (Traditional GMM=0.38, Adaboost.M1=0.7, Naïve-Bayes=0.75), and the scoring results of improved GMM have a high level of agreement with the expert scoring (kappa=0.67). Conclusions: The results show that the proposed method based on the improved Gaussian mixture model can effectively perform the FMS assessment task and it is potentially feasible to use depth cameras for FMS assessment.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

We reduplicate the Book “Dark Energy” by M. Li, X-D. Li, and Y. Wang, zero-point energy calculation with an unexpected “length’ added to the ‘width’ of a graviton wavefunction just prior to the entrance of ‘gravitons’ to a small region of space-time prior to a nonsingular start to the universe. We compare this to a solution worked out using Klauder Enhanced quantization, for the same given problem. The solution of the first Cosmological Constant problem relies upon the geometry of the multiverse generalization of CCC cosmology which is explained in this paper. The second solution, used involves Klauder enhanced quantization. We look at energy given by our methods and compare and contrast it with the negative energy of the Rosen model for a mini sub universe and estimate GW frequencies

The circular photogalvanic effect (CPGE) is the photocurrent generated in an optically active material in response to an applied ac electric field, and it changes sign depending on the chirality of the incident circularly polarized light. It is a non-linear dc current as it is second-order in the applied electric field, and for a certain range of low frequencies, takes on a quantized value proportional to the topological charge for a system which is a source of nonzero Berry flux. We show that for a non-interacting double-Weyl node, the CPGE is proportional to two quanta of Berry flux. On examining the effect of short-ranged Hubbard interactions upto first-order corrections, we find that this quantization is destroyed. This implies that unlike the quantum Hall effect in gapped phases or the chiral anomaly in field theories, the quantization of the CPGE in topological semimetals is not protected.

Plantar flexors (PF) spasticity is known to poorly correlate with active dorsiflexion (DF) impairment throughout the swing phase of hemiparetic gait. Spastic Cocontraction, instead, stemming from descending pathways, potentially misdirect antagonist PF activity opposing DF during swing. Electromyographic (EMG) recordings, while unable to differentiate between reflex-based and descending origins, may offer valuable insights into this distinction by exploring PF EMG activity after tibial nerve neurotomy (which eliminates PF spasticity). Eleven subjects with hemiparesis walking at comfortable velocity and 11 controls walking at comfortable and slow velocity, underwent kinematic and PF/DF EMG analysis. Five of the hemiparetic subjects underwent tibial neurotomy &gt;1 year prior. We evaluated spasticity at rest (Tardieu scale), maximal ankle dorsiflexion, tibialis anterior agonist recruitment and gastrocnemius medialis and soleus cocontraction coefficients during swing. At slow velocity, controls (0.80±0.12 m/s) moved at a similar pace as hemiparetic subjects (0.73±0.37 m/s, NS). Hemiparetic subjects showed: (i) reduced ankle DF across swing (ii) increased PF cocontraction, including before any DF (iii) higher cocontraction despite absent spasticity in tibial neurotomy subjects (iv) higher tibialis anterior recruitment. Increased PF cocontraction occurs in the absence of spasticity or ankle DF despite higher agonist recruitment. Spastic cocontraction is a major factor limiting active DF at swing, unlike spasticity.

The precise determination of the State-of-Health (SOH) of lithium-ion batteries is critical in the domain of battery management systems. The proposed model in this research paper emulates any deep learning or machine learning model by utilizing a Look Up Table (LUT) memory to store all activation inputs and their corresponding outputs. The operation that follows the completion of training is referred to as the LUT memory preparation procedure. The lookup operation performed on this method simply substitutes for the inference process. This is achieved by discretizing the input data and features before binarizing them. The term for the aforementioned operation is the LUT inference method. The procedure was evaluated in this study using two distinct neural network architectures: a bidirectional long short-term memory (LSTM) architecture and a standard fully connected neural network (FCNN). It is anticipated that considerably greater efficiency and velocity will be achieved during the inference procedure when the pre-trained deep neural network architecture is inferred directly. The principal aim of this research is to construct a lookup table that effectively establishes correlations between the SOH of lithium-ion batteries and ensures a degree of imprecision that is tolerable. According to the results obtained from the NASA PCoE lithium-ion battery dataset, the proposed methodology exhibits performance that is largely comparable to that of the initial machine learning models. Utilising the error assessment metrics RMSE, MAE, and (MAPE), the accuracy of SOH prediction has been quantitatively evaluated. The indicators mentioned above demonstrate a significant degree of accuracy when predicting SOH.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Density distribution function of classical statistical mechanics is generally generalized as a product of a general complex function and its complex Hermitian conjugate function, and the average of classical statistical mechanics is generalized as the average of the quantum mechanics. Furthermore, this paper derives three ones of the five axiom presumptions of quantum mechanics, e.g., deduces Schrȍdinger equation by two general ways, makes the three axiom presumptions into three theorems of quantum mechanics, not only solves the crisis to hard understand, but also gets new theories and new discoveries, e.g., this paper solves the crisis of the origin of the wave-particle duality, derives operators, eigenvalues and eigenstates, deduces commutation relations for coordinate and momentum as well as the time and energy, and discovers quantum mechanics is just a generalization ( mechanics ) theory of the complex square root of ( real density function of ) classical statistical mechanics. Quantum mechanics being just a generalization theory of the complex square root of classical statistical mechanics is both new physics and revolutionary discovery, which are affecting people’s deep philosophical thinking for modern physics development, solve all the crisises of quantum mechanics, quantum information and so on, and make quantum mechanics have scientific solid bases being checked and both no basic axiom presumption and no all the quantum strange incomprehensible properties, because classical statistical mechanics and the complex square root of classical statistical mechanics have the scientific solid bases being checked. In addition, this paper discovers the reason no taking the time derivative of space coordinates in Schrȍdinger equation. Therefore, this paper gives solution to the crisis of the first quantization origin, and mainly deduces quantum physics no all the quantum current strange incomprehensible properties.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

The efficient recognition and classification of personal protective equipment are essential for en-suring the safety of personnel in complex industrial settings. Using the existing methods, manually performing macro-level classification and identification of personnel in intricate spheres is tedious, time-consuming, and inefficient. The availability of several artificial intelligence models in recent times presents a new paradigm shift in object classification and tracking in complex settings. In this study, several compact and efficient deep learning model architectures are explored, and a new efficient model is constructed by fusing the learning capabilities of the individual, efficient models for better object feature learning and optimal inferencing. The new model construct follows the contributory learning theory whereby each fussed model brings its learned features, which are then combined to obtain a more accurate and rapid model using normalized quantization-aware learning. During the investigation, a separable convolutional driven model was constructed as a base model, and then the various efficient architectures combined for the rapid identification and classification of the various hardhat classes used in complex industrial settings. A remarkable rapid classification and accuracy were recorded with the new resultant model.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Quantum physics is intrinsically probabilistic. The entropy of a quantum state quantifies the amount of randomness (or information loss) of such state. The degrees of freedom of a quantum state are position and spin, and upon their specification Born's rule in phase space defines randomness. We focus on the spin degree of freedom and elucidate the spin entropy. Then, we present some of its properties and show how entanglement increases spin entropy. Some speculative predictions on the decay of the $Z^0,W^{+,-}$ gauge bosons conclude the paper.

Viruses have established symbiotic relationships with almost every other living organism on Earth and at all levels of biological organisation, from other viruses up to entire ecosystems. In most cases, peacefully coexisting with their hosts, but in most relevant cases, parasitising them and inducing diseases. Viruses are playing an essential role in shaping the eco-evolutionary dynamics of their hosts, and have been also involved in some of the major evolutionary innovations either by working as vectors of genetic information or by being themselves coopted by the host into their genomes. Viruses can be studied at different levels of biological organisation, from the molecular mechanisms of genome replication, gene expression and encapsidation, to global pandemics. All these levels are different and yet connected through the presence of threshold conditions allowing for the formation of a capsid, the loss of genetic information or epidemic spreading. These thresholds, as it occurs with temperatures separating phases in a liquid, define sharp qualitative types of behaviour. These {\em phase transitions} are very well known in Physics. They have been studied by means of simple, but powerful models able to capture their essential properties, allowing to understand them. Can the physics of phase transitions be an inspiration for our understanding of viral dynamics at different scales? Here we review well-known examples of transition phenomena in virology and their simplest mathematical modelling approaches. We suggest that the advantages of abstract, simplified pictures used in Physics are also the key to properly understand the origins and evolution of complexity in viruses. By means of several examples, we explore this multilevel landscape and how minimal models provide deep insights into a diverse array of problems. The relevance of these transitions in connecting dynamical patterns across levels and their evolutionary and clinical implications are outlined.

A drug repositioning effort supported the possible use of the anti-HIV drug etravirine as a treatment for Friedreich Ataxia (FRDA). Etravirine increases frataxin protein and corrects the biochemical defects in cells derived from FRDA patients. Because of these findings, and since etravirine displays a favorable safety profile, we conducted this pilot open-label phase 2 clinical trial assessing the safety and potential efficacy of etravirine in FRDA patients. Thirty-five patients were stratified into 3 severity groups and randomized to etravirine 200 mg/day or 400 mg/day. They were treated for 4 months. Efficacy endpoints were represented by changes in peak oxygen uptake and workload as measured by incremental exercise test, SARA score, cardiac measures, measures of QoL and disability. Data were collected 4 months before the start of the treatment (T-4), at the start (T0), at the end (T4) and 4 months after the termination of the treatment (T+4). Etravirine was well tolerated. Etravirine completely stopped the progression of the SARA score during the 4-months treatment period, compared to the 4 months pre and post treatment. It increased peak workload, while the improvement of peak oxygen uptake was not statistically significant. No changes in the cardiac measures were observed. Health and QoL measures showed a worsening at the suspension of the drug. In this open trial etravirine significantly improved neurological function and was generally safe and reasonably tolerated. This suggests that etravirine represents a potential therapeutic agent in FRDA deserving testing in a randomized placebo controlled clinical trial.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

Viral infection can regulate the cell cycle, thereby promoting viral replication. Hijacking and altering the cell cycle are important for the virus to establish and maintain latent infection. Previously, Spodoptera exigua multiple nucleopolyhedrovirus (SeMNPV) latently infected P8-Se301-C1 cells, which grew more slowly than Se301 cells and interfered with homologous SeMNNPV superinfection, were established. However, the effects of latent and superinfection with baculoviruses on cell cycle progression remain unknown. In this study, the cell cycle profiles of P8-Se301-C1 cells, and SeMNPV or Autographa californica mutiple nucleopolyhedrovirus (AcMNPV) infected P8-Se301-C1 cells were characterized by flow cytometry. The results showed that replication-related genes MCM4, PCNA, and BAF were down-regulated (p < 0.05) in P8-Se301-C1 cells and the S phase of P8-Se301-C1 cells was longer than that of Se301 cells. P8-Se301-C1 cells infected with SeMNPV did not arrest in G2/M phase and or affect the expression of Cyclin B and cyclin-dependent kinase 1 (CDK1). Furthermore, when P8-Se301-C1 cells were infected with SeMNPV after synchronized treatment with hydroxyurea and nocodazole, light microscopy and qRT-PCR analysis showed that compared with unsynchronized cells and S and G2/M phase cells, SeMNPV-infected P8-Se301-C1 cells in G1 phase induced G2/M phase arrest, and the amount of virus adsorption and intracellular viral DNA replication were significantly increased (p < 0.05). In addition, the BV production and the OB containing cells were both increased at 120 h post-infection (p < 0.05). The expression of Cyclin B and CDK1 was significantly down-regulated at 48 h post infection (p < 0.05). Finally, arrest of SeMNPV-infected G1 phase cells in the G2/M phase increased BV production (p < 0.05) and the number of OB containing cells. In conclusion, G1 phase infection and G2/M arrest are favorable to SeMNPV proliferation in P8-Se301-C1 cells, thereby alleviating the homologous superinfection exclusion. The results contribute to a better understanding of the relationship between baculoviruses and insect cell cycle progression regulation.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

The idealized rhombohedral unit cell of boron carbide is formed by a 12-atom icosahedron and a 3-atom linear chain. Phase transitions are second order and caused by the exchange of B and C sites or by vacancies in the structure. Nevertheless, the impact of such minimal structural changes on the properties can be significant. As the X-ray scattering cross sections of B and C atoms are very similar, the capability of X-ray fine structure investigation is restricted. Phonon spectroscopy helps closing this gap. Phase transitions known to date have been identified due to significant changes of properties: (1) The phase transition near the chemical composition B8C by clear change of the electronic structure; (2) The endothermic temperature-dependent phase transition at 712 K by the according change of specific heat; (3) The high-pressure phase transition at 33.2 GPa by the drastic change of optical appearance from opacity to transparency. These phase transitions affect IR- and Raman-active phonons and other solid-state properties. The phase transitions at B~8C and 712 K mean that a well-defined distorted structure is converted into another one each. In the high-pressure phase transition, an apparently well-defined distorted structure changes into a highly ordered one. In all these cases, the distribution of polar C atoms in the icosahedra plays a crucial role.

Quantum physics through the lenses of Bayesian statistics consider probabilities to be degree of believes or knowledge and subjective. A Bayesian derivation of the probability density function in phase space is presented. The entropy proposed by Geiger and Kedem \cite{GeiKed2022a,GeiKed2022b} in phase space is expanded to define quantitatively interference and entanglement. Comparisons between each of these two quantities and the entropy are made. A brief presentation of entanglement in phase space to the spin degree of freedom and to mixed states completes the work.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

We study the deterministic dynamics of N point particles moving at constant speed in a 2D table made of two polygonal urns connected by an active rectangular channel, which applies a feedback-control on the particles, inverting the horizontal component of their velocities, when their number in the channel exceeds a fixed threshold. Such a bounce--back mechanism is non-dissipative: it preserves volumes in phase space. An additional passive channel closes the billiard table forming a circuit in which a stationary current may flow. Under specific constraints on the geometry and on the initial conditions, the large N limit allows nonequilibrium phase transitions between homogeneous and inhomogeneous phases. The role of ergodicity in making a probabilistic theory applicable is discussed both for rational and irrational urns. The theoretical predictions are compared with the numerical simulation results. Connections with the dynamics of feedback-controlled biological systems are highlighted.

We show that the van der Waals gas does not exhibit just the celebrated liquid-gas 1 transition but also a quantum-classical one. We study the issue with reference to the LMC statistical 2 complexity and in relation to the order-disorder contrast.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

We utilize how Weber in 1961 initiated the process of quantization of early universe fields to the problem of what may be emitted at the mouth of a wormhole. While the wormhole models are well developed, there is as of yet no consensus as to how, say GW or other signals from a wormhole mouth could be quantized, or made to be in adherence to a procedure Weber cribbed from Feynman, in 1961. In addition, we utilize an approximation for the Hubble parameter parameterized from Temperature using Sarkar’s H ~ Temperature relations, as given in the text . Finally after doing this we go to the Energy as E also ~ Temperature, and from there use E (energy) as ~ signal frequency. This gives us an idea of how to estimate frequency generated at the mouth of a wormhole.

The quantization error (QE) from Self-Organizing Map (SOM) output after learning is exploited in this studies. SOM learning is applied on time series of spatial contrast images with variable relative amount of white and dark pixel contents, as in monochromatic medical images or satellite images. It is proven that the QE from the SOM output after learning provides a reliable indicator of potentially critical changes in images across time. The QE increases linearly with the variability in spatial contrast contents of images across time when contrast intensity is kept constant. The hitherto unsuspected capacity of this metric to capture even the smallest changes in large bodies of image time series after using ultra-fast SOM learning is illustrated on examples from SOM learning studies on computer generated images, MRI image time series, and satellite image time series. Linear trend analysis of the changes in QE as a function of the time an image of a given series was taken gives proof of the statistical reliability of this metric as an indicator of local change. It is shown that the QE is correlated with significant clinical, demographic, and environmental data from the same reference time period during which test image series were recorded. The findings show that the QE from SOM, which is easily implemented and requires computation times no longer than a few minutes for a given image series of 20 to 25, is useful for a fast analysis of whole series of image data when the goal is to provide an instant statistical decision relative to change/no change between images.

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography-mass spectrometry. The reaction mechanism of alkane solution concentration and temperature in the adsorption process was investigated. The adsorption characteristics of heptadecane on the surface and pores of illite and kerogen were elucidated by adsorption isotherm model and adsorption thermodynamic model. The results show that: The concentration of alkane solution contributes to the adsorption of illite and kerogen. As the concentration of the solution continues to increase, the adsorption rate gradually slows down. However, the temperature hardly affects the adsorption rate. At 25℃, 50℃ and 60℃, the adsorption process of illite on alkane solution is more consistent with Langmuir model and Freundlich model, respectively. The difference is that Langmuir model is suitable for describing the whole adsorption process of kerogen on alkane solution. 3) The adsorption process of illite and kerogen to heptadecane solution is an endothermic reaction. Heating helps to accelerate the migration rate of alkanes, which is conducive to the adsorption reaction. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level, and fill the research gap in the application of solid-liquid isothermal adsorption physical experiments to the adsorption and occurrence of shale oil.

Sarcopenia becomes more common with age, being most prevalent among elderly individuals. According to the EWGSOP, muscle mass is one of the criteria for the evaluation of sarcopenia. The main methods for evaluating muscle mass are CT, MRI, and DXA, but these methods are difficult to apply in the field due to equipment costs, radioactivity, and lack of portability. BIVA and PhA are alternative approaches for assessing somatic cell mass and volume and do not require predictive equations. These variables are clinically relevant parameters that indicate cell health, especially cell membrane integrity and cell function. This study in sarcopenic and nonsarcopenic elderly volunteers aimed to determine the BIVA distribution pattern among individual sarcopenia patients; to evaluate the relationship between PhA and muscle strength, muscle quality, and physical function; and to find any correlates of PhA. The sample comprised 134 free-living elderly individuals of both sexes aged 69–91 years. Anthropometric parameters, grip strength, DXA findings, BIA results, and physical performance (the 6-meter walk test) were measured. Impedance vector distributions were evaluated in sarcopenia patients and healthy elderly individuals using BIVA. According to the AWGS criteria, sarcopenia was diagnosed according to DXA findings, grip strength and physical performance test results. Group differences were evaluated using the t test, Mann‒Whitney U test, and Hotelling's T2 test. Correlation analysis was performed to identify variables significantly associated with PhA. Linear regression analysis was performed to determine whether PhA was associated with muscle strength, muscle quality and physical function. BIVA detected a significant difference between the sarcopenia and non-sarcopenia groups (both sexes) due to higher R/H values and lower phase angles in a few individuals, whereas Xc/Ht values did not differ between the two groups. The sarcopenia group had a significantly lower PhA than the non-sarcopenia group among both males (p&lt;0.01) and females (p&lt;0.05). PhA was significantly correlated with age, ASM, HGS, and muscle quality in both sexes and significantly correlated with ASM/Ht2 and physical performance in males. PhA was a significant indicator of muscle strength in both males (β = 2.6; p&lt;0.01) and females (β = 3.4; p&lt;0.01), a significant indicator of muscle quality in both males (β = 0.07; p&lt;0.05) and females (β = 0.17; p&lt;0.01), and a significant indicator of physical performance in males (β = 0.3; p&lt;0.01). BIVA can detect changes in muscle mass in individuals with sarcopenia and is a practical method for the assessment of sarcopenia in the field. PhA is a good indicator of muscle strength, muscle quality and physical performance (in males). These methods can help diagnose sarcopenia in elderly individuals with reduced mobility.

The 8Nb isopleth section of a Ti-Al-Nb system is experimentally determined based on thermal analysis and thermodynamic calculation methods to obtain the phase transformation and equilibrium relations required for material design and fabrication. The phase transus and relations for the 8Nb-TiAl system show some deviations from the calculated thermodynamic results. The ordered βo phase transforms from the disordered β/α phases at 1200–1400 °C over a large Al concentration range, and this transformation is considered to be an intermediate type between the first- and second-order phase transitions. Moreover, the βo phases are retained at the ambient temperature in the 8Nb-TiAl microstructures. The ωo phase transforms from the highly ordered βo phase, rather than from α2 or βo with low degree of atom ordering B2 (LOB2) structure, with Al concentration of 32–43 at.% at approximately 850 °C. From the experimental detection, the transition of the ωo phase from the βo phase is considered to be a further ordering process.

Zinc oxide (ZnO) nanostructures have been studied extensively in the past years due to the novel electronic, photonic, mechanical and electrochemical properties. Recently, more attention has been paid to assemble nanoscale building blocks into three dimensional (3D) complex hierarchical structures, which not only inherit the excellent properties of the single building blocks but also provide potential applications in the bottom-up fabrication of functional devices. This review article focuses on 3D ZnO hierarchical nanostructures, and summarizes major advances in the solution phase synthesis, applications in environment, and electrical/electrochemical devices. We present the principles and growth mechanisms of ZnO nanostructures via different solution methods, with an emphasis on rational control of the morphology and assembly. We then discuss the applications of 3D ZnO hierarchical nanostructures in photocatalysis, field emission, electrochemical sensor, and lithium ion batteries. Throughout the discussion, the relationship between the device performance and the microstructures of 3D ZnO hierarchical nanostructures will be highlighted. This review concludes with a personal perspective on the current challenges and future researches.

Ant Colony Optimization (ACO) is a stochastic optimization algorithm inspired by the foraging behavior of ants. We investigate a simplified computational model of ACO, wherein ants sequentially engage in binary decision-making tasks, leaving pheromone trails contingent upon their choices. The quantity of pheromone left is the number of correct answers. We scrutinize the impact of a salient parameter in the ACO algorithm, specifically, the exponent $\alpha$ that governs the pheromone levels in the stochastic choice function. In the absence of pheromone evaporation, the system is accurately modeled as a multivariate nonlinear P\'{o}lya urn, undergoing a phase transition as $\alpha$ varies. The probability of selecting the correct answer for each question asymptotically approaches the stable fixed point of the nonlinear P\'{o}lya urn. The system exhibits dual stable fixed points for $\alpha\ge \alpha_c$ and a singular stable fixed point for $\alpha<\alpha_c$. When pheromone evaporates over a time scale $\tau$, the phase transition does not occur and leads to a bimodal stationary distribution of probabilities for $\alpha\ge \alpha_c$ and a monomodal distribution for $\alpha<\alpha_c$.

The need for continuous research to refine the models used in accident reconstruction appears with the development of new car models that satisfy consumer complaints. The paper analyzed a sub-sequence of car and pedestrian accidents, from the perspective of the distance traveled by them in the contact phase, with the aim of improving the information regarding the reconstruction of road accidents. The research included the analysis of some accidents with pedestrian dummies, as well as the simulation of the impact between different classes of vehicles and pedestrians in two different walking positions. Specialized software was used with complex multibody models of pedestrians, modifying the speed and deceleration parameters at the time of the collision. The research results highlight the differences between bilinear models used in accident reconstruction and the proposed study. They can also be used to determine the distance traveled by the vehicle in the first phase of the collision with pedestrians.

This paper discusses the basic concepts of phase dislocations and vortex formation in the electric fields of fundamental air core mode of hollow core waveguides with specific types of rotational symmetry of the core – cladding boundary. Analysis of the behavior of the electric field phase in the transmission bands shows that the mechanism of light localization in the hollow core waveguides with discrete rotational symmetry of the core – cladding boundary cannot be completely described by the ARROW model. For an accurate description of the phase behavior, it is necessary to account for phase jumps of the magnitude of π when passing through the phase dislocations.

Mereotopology is a concept rooted in analytical philosophy. The phase-field concept is based on mathematical physics and finds applications in materials engineering. The two concepts seem to be disjoint at a first glance. While mereotopology qualitatively describes static relations between things like x isConnected y (topology) or x isPartOf y (mereology) by first order logic and Boolean algebra, the phase-field concept describes the geometric shape of things and its dynamic evolution by drawing on a scalar field. The geometric shape of any thing is defined by its boundaries to one or more neighboring things. The notion and description of boundaries thus provides a bridge between mereotopology and the phase-field concept. The present article aims to relate phase-field expressions describing boundaries and especially triple junctions to their Boolean counterparts in mereotopology and contact algebra. An introductory overview on mereotopology is followed by an introduction to the phase-field concept already indicating first relations to mereo- topology. Mereotopological axioms and definitions are then discussed in detail from a phase-field perspective. A dedicated section introduces and discusses further notions of the isConnected relation emerging from the phase-field perspective like isSpatiallyConnected, isTemporallyConnected, isPhysicallyConnected, isPathConnected and wasConnected. Such relations introduce dynamics and thus physics into mereotopology as transitions from isDisconnected to isPartOf can be described.

In the article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal aging after so-lution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC), and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) during cooling (from +1500C to -500C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20 and 100 hours at 500°C; (2) during heating (from -500C to +1500C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19’) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time, (4) the width of the total temperature range of the transformation M(B19’)  A(B2) during heating changes from large (∆T=49,7°C), after solution annealing, to narrow (∆T=19.3°C and ∆T=17.9°C after 20 h and 100 h of ageing) and, most importantly, (5) a comparison with literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of the fact whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite  austenite transformation in the same temperature range.

As novel materials for carbon capture, phase change solvents can separate into two immiscible phases during the CO2 capturing procedure under a certain temperature. The solvent systems can significantly decrease the energy consumption since the solvents can be regenerated by only heating the rich-CO2 phase. In this work, amino acid ionic liquids (AAILs) were synthesized using quaternary ammonium salts and amino acids as raw materials, and the aqueous solutions were prepared as novel liquid-solid phase change solvents. The results showed that the solvents had excellent CO2 absorption capacity, and the AAILs functionalized by glycine and tryptophan exhibited significant phase change properties. The mechanism of phase-change of the solvent were mainly due to the lower solubility of the product after reaction between AAILs and CO2. The solvent with tryptophan as anion could be regenerated by only heating the CO2-riched solid phase, which might significantly decrease energy consumption of regeneration. And the absorbent could be reused with the regenerated absorption ratio up to 79%. The solvent system has great potential in industrial application due to the easy operation process and efficient recycling ability.

Pulsed-field gradient (PFG) diffusion experiments can be used to measure anomalous diffusion in many polymer or biological systems. However, it is still complicated to analyze PFG anomalous diffusion, particularly the finite gradient pulse width (FGPW) effect. In practical applications, the FGPW effect may not be neglected such as in clinical diffusion magnetic resonance imaging (MRI). Here, two significantly different methods are proposed to analyze PFG anomalous diffusion: the effective phase shift diffusion equation (EPSDE) method and an observing the signal intensity at the origin method. The EPSDE method describes the phase evolution in virtual phase space, while the method to observe the signal intensity at the origin describes the magnetization evolution in real space. However, these two approaches give the same general PFG signal attenuation including FGPW effect, which can be numerically evaluated by a direct integration method. The direct integration method is fast and without overflow. It is a convenient numerical evaluation method for Mittag-Leffler function type PFG signal attenuation. The methods here provide a clear view of spin evolution under field gradient, and their results will help the analysis of PFG anomalous diffusion.

Numerical models widely used for hydrocarbon phase behavior and compositional flow simulations are based on assumption of thermodynamic equilibrium. However, it is not uncommon for oil and gas-condensate reservoirs to exhibit essentially non-equilibrium phase behavior, e.g., in the processes of secondary recovery after pressure depletion below saturation pressure, or during gas injection, or for condensate evaporation at low pressures. In many cases the ability to match field data with equilibrium model depends on simulation scale. The only method to account for non-equilibrium phase behavior adopted by the majority of flow simulators is the option of limited rate of gas dissolution (condensate evaporation) in black oil models. For compositional simulations no practical yet thermodynamically consistent method has been presented so far except for some upscaling techniques in gas injection problems. Previously reported academic non-equilibrium formulations have a common drawback of doubling the number of flow equations and unknowns compared to the equilibrium formulation. In the paper a unified thermodynamically-consistent formulation for compositional flow simulations with non-equilibrium phase behavior model is presented. Same formulation and a special scale-up technique can be used for upscaling of an equilibrium or non-equilibrium model to a coarse-scale non-equilibrium model. A number of test cases for real oil and gas-condensate mixtures are given. Model implementation specifics in a flow simulator are discussed and illustrated with test simulations. A non-equilibrium constant volume depletion algorithm is presented to simulate condensate recovery at low pressures in gas-condensate reservoirs. Results of satisfactory model matching to field data are reported and discussed.

The short-lived positron-emitter carbon-11 (t1/2 = 20.4 min; b+, 99.8%) is prominent for labeling tracers for use in biomedical research with positron emission tomography (PET). Carbon-11 is produced for this purpose with a cyclotron, nowadays almost exclusively by the 14N(p,a)11C nuclear reaction, either on nitrogen containing a low concentration of oxygen (0.1–0.5%) or hydrogen (~ 5%) to produce [11C]carbon dioxide or [11C]methane, respectively. These primary radioactive products can be produced in high yields and with high molar activities. However, only [11C]carbon dioxide has some utility for directly labeling PET tracers. Primary products are required to be converted rapidly and efficiently into secondary labeling synthons to provide versatile radiochemistry for labeling diverse tracer chemotypes at molecular positions of choice. This review surveys known gas phase transformations of carbon-11 and summarizes the important roles that many of these transformations now play for producing a broad range of labeling synthons in carbon-11 chemistry.

One of the intriguing recent results in the field of high-entropy alloys is the discovery of single-phase equiatomic multi-component Laves intermetallics. However, there is no clear understanding that a combination of chemical elements will form such high-entropy compounds. Here we contribute to understanding this issue by modifying the composition of duodenary TiZrHfNbVCrMoMnFeCoNiAl (12x) alloy in which we recently reported the fabrication of hexagonal C14 Laves phase. We consider three alloys based on 12x: 7x=12x-VCrMoMnFe, 12x+Sc, 12x+Be and observe that all of them crystalize with the formation of C14 Laves phase as a dominant structure. We report that 12x+Be alloy reveals single-phase C14 structure with very high concentration of structural defects and ultra-fine dendritic microstructure with almost homogenous distribution of the constituted elements over the alloy matrix. The 7x and 12x+Sc alloys contain C14 as a main phase and unknown impurity phases. To characterize the materials, we examine their heat capacity, electrical conductivity and magnetic properties. The measurements reveal that the Laves phases are Curie-Weiss paramagnets, which demonstrate metallic conduction; 7x and 12x alloys also reveal a pronounced Kondo-like anomaly. Analysis of experimental data as well as ab initio calculations suggests that chemical complexity and compositional disorder cause strong s-d band scattering and thus the rather high density of d-states in the conduction band. Analysis of the results suggests that the mechanism of Laves phase formation in multicomponent multi-principal element metallic alloys is may be the same as in polydisperse hardspheres mixtures. Another important conclusion is that the configurational entropy is a negligible factor in the stabilization of multi-element Laves phases.

Solar neutrinos have played a central role in the discovery of the neutrino oscillation mechanism. They still are proving to be a unique tool to help investigate the fusion reactions that power stars and further probe basic neutrino properties. The Borexino neutrino observatory has been operationally acquiring data at Laboratori Nazionali del Gran Sasso in Italy since 2007. Its main goal is the real-time study of low energy neutrinos (solar or originated elsewhere, such as geo-neutrinos). The latest analysis of experimental data, taken during the so-called Borexino Phase-II (2011-present), will be showcased in this talk - yielding new high-precision, simultaneous wide band flux measurements of the four main solar neutrino components belonging to the "pp" fusion chain (pp, pep, ⁷Be, ⁸B), as well as upper limits on the remaining two solar neutrino fluxes (CNO and hep).

Quantitative phase microscopy (QPM), a technique combining phase imaging and microscopy, enables visualization of the 3-D topography in reflective samples as well as the inner structure or refractive index distribution of transparent and translucent samples. However, as in conventional optical microscopy, QPM provides either a large field of view (FOV) or a high resolution but not both. Many approaches such as oblique illumination, structured illumination and speckle illumination have been proposed to improve the spatial resolution of phase microscopy by restricting other degrees of freedom (mostly time). Therefore, the space bandwidth product (SBP) of QPM becomes enlarged. This paper aims to provide an up-to-date review on the resolution enhancement approaches of QPM, discussing the pros and cons of each technique as well as the confusion on resolution definition claim on QPM and other coherent microscopy.

Interface between matrix/coating or coating/coating in fact represents a very complicate thin interfacial layer. So interface model is necessary to avoid the difficulty on considering such a complicate thin layer in analysis. Classic interface model and cohesive model have been widely used in stress analysis of coating materials, though they cannot represent the effect of very thin interfacial layer accurately. A complete interface model has been deduced from the equivalent constitutive of interfacial layer in this paper. It is found that both classic interface model and cohesive model sometimes cannot give correct analysis results, while the complete interface model can always give a correct result. Moreover, the stress parallel to interface within the interfacial layer can also be analyzed by the new model. Besides, this model can also be used to describe the equivalent properties of interfacial layer, thereby, can provide a quantitative characterizing method for interfacial layer itself.

In contrast to animals, adult organs in plants are not determined during embryogenesis but gen-erated from meristematic cells as plants advance through development. Plant development in-volves a succession of different phenotypic stages and the transition between these stages is termed phase transition. Phase transitions need to be tightly regulated and coordinated to ensure they occur under optimal seasonal, environmental conditions. Polycarpic perennials transition through vegetative stages and the mature, reproductive stage many times during their lifecycles and, in both perennial and annual species, environmental factors and culturing methods can re-verse the otherwise unidirectional vector of plant development. Epigenetic factors regulating gene expression in response to internal cues and external (environmental) stimuli influencing the plant’s phenotype and development have been shown to control phase transitions. How develop-mental and environmental cues interact to epigenetically alter gene expression and influence these transitions are not well understood and understanding this interaction is important considering the current climate change scenarios, since epigenetic maladaptation could have catastrophic con-sequences for perennial plants in natural and agricultural ecosystems. Here we review studies focussing on the epigenetic regulators of the vegetative phase change and highlight how these mechanisms might act in exogenously induced plant rejuvenation and regrowth following stress.

1,3,5-Tris-(α-naphthyl)benzene is an organic non-electrolyte with notable stability of an amorphous phase. Its glassy and supercooled liquid states were previously studied by spectroscopic and calorimetric methods. However, the thermodynamic parameters of phase transitions available from the literature are inconsistent. In this work, the heat capacities of crystalline and liquid phases, the temperature dependence of the saturated vapor pressures, fusion and vaporization enthalpies were determined using differential and fast scanning calorimetry and verified using the estimates based on solution calorimetry. The structural features of 1,3,5-tris-(α-naphthyl)benzene are discussed based on the computations performed and the data on the molecular refractivity. The consistency between the values obtained by independent techniques was demonstrated. The deviations in the previously published data were attributed to possible polymorphism.

This study delves into the Schrödinger equation's new invariants, shedding light on their crucial implications for theoretical physics and beyond. Specifically, it explores the behavior of scattering amplitudes and bound states concerning the choice of coordinate systems. The research unveils that while the energy of bound states remains invariant under coordinate transformations, the phase of scattering amplitudes undergoes variations, underscoring its pivotal role in theories reliant on phase normalization. Moreover, these findings have played a pivotal role in constructing estimates for three-dimensional Navier-Stokes equations, enhancing our ability to model complex fluid dynamics with greater precision and reliability. Additionally, in seismic exploration, tomography, and ultrasound imaging, these properties allow researchers to optimize phase selection, facilitating the most effective interpretation of measurement results. This strategic phase manipulation ensures clearer insights into subsurface structures, tissue composition, and fluid dynamics, with the flexibility to seamlessly transition back to the original coordinate system post-interpretation. This interdisciplinary synergy underscores the profound impact of fundamental theoretical research on advancing practical applications across diverse scientific domains.

The quadratic polynomial differential systems in the plane are the easiest nonlinear differential systems. They have been studied intensively due to their nonlinearity and to their big number of applications. These systems can be classified in ten classes. Here we provide all the topologically different phase portraits in the Poincaré disc of two of these classes.

Abstract: The most common genetic cause of amyotrophic lateral sclerosis (ALS) and frontotemporal dementia (FTD) is the presence of poly-PR/GR dipeptide repeats which are encoded by the C9orf72 gene. Recently, it was shown that poly-PR/GR alters chromatin accessibility which results in stabilization and enhancement of transcriptional activity of the tumor suppressor p53 in several neurodegenerative disease models. Reduction of p53 protein levels in cell and model organisms protects against neurotoxicity of poly-PR, and partially protects against neurotoxicity of poly-GR. Here, we aimed to study the detailed molecular mechanisms how p53 contributes to poly-PR/GR mediated neurodegeneration. Using a combination of biophysical techniques such as nuclear magnetic resonance (NMR) spectroscopy, fluorescence polarization, turbidity assays and differential interference contrast (DIC) microscopy, we found that p53 physically interacts with poly-PR/GR and triggers liquid-liquid phase separation of p53. We identified p53 transactivation domain 2 (TAD2) as the main binding site for PR25/GR25 and show that binding of poly-PR/GR to p53 is mediated by a network of electrostatic and/or hydrophobic interactions. Our findings might help to understand the mechanistic role of p53 in poly-PR/GR - associated neurodegeneration.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

We scrutinize the reliability of multilooked interferograms for deformation analysis. Designing a simple approach in the evaluation of the accuracy of the estimated deformation signals, we reveal a prominent bias in the deformation velocity maps. The bias is the result of propagation of small phase error of multilooked interferograms through the time series and can sum up to 6.5 mm/yr in case of using the error prone short temporal baseline interferograms. We further discuss the role of the phase estimation algorithms in reduction of the bias and put recommend a unified intermediate InSAR product for achieving high-precision deformation monitoring.

The organo-catalyzed enantioselective benzylation reaction of α-trifluoromethoxy indanones afforded α-benzyl-α-trifluoromethoxy indanones with a tetrasubstituted stereogenic carbon center in excellent yield with moderate enantioselectivity (up to 57% ee). Cinchona alkaloid-based chiral phase transfer catalysts were found to be effective for this transformation, and both enantiomers of α-benzyl-α-trifluoromethoxy indanones were accessed, depended on the use of cinchonidine and cinchonine-derived catalyst. The method was extended to the enantioselective allylation reaction of α-trifluoromethoxy indanones to give the allylation products in moderate yield with good enantioselectivity (up to 76% ee).

We investigated fabrication of neodymium doped thin film optical waveguide-based devices as potential active sources for planar integrated optics. Liquid-phase epitaxial growth was used to fabricate neodymium-doped yttrium aluminum borate films on compatible lattice-matched un-doped yttrium aluminum borate substrates. We observed the refractive index contrast of the doped and un-doped crystal layers by differential interference contrast microscopy. In addition, characterization by X-ray powder diffraction, optical absorption and luminescence spectra demonstrated the crystal quality and uniformity and optical guiding of the resulting thin films.

Nonlinear rheological properties of chiral crystal cholesteryl oleyl carbonate (COC) in blue phase III are investigated under different shear deformations; large amplitude oscillatory shear, step shear deformation, and continuous shear flow. Rheology of the liquid crystal is significantly affected by structural rearrangement of defects under shear flow. One of the examples on the defect-mediated rheology is the blue phase rheology. Blue phase is characterized by three dimensional network structure of the disclination lines. It has been numerically studied that the rheological behavior of the blue phase is dominated by destruction and creation of the disclination networks. In this study, we find that the nonlinear viscoelasticity of BPIII is characterized by the fracture of the disclination networks. Depending on the degree of the fracture, the nonlinear viscoelasticity is divided into two regimes; the weak nonlinear regime where the disclination network locally fractures but still show elastic response, and the strong nonlinear regime where the shear deformation breaks up the networks, which results in a loss of the elasticity. Continuous shear deformation reveals that a series of the fracture process delays with shear rate. The shear rate dependence suggests that force balance between the elastic force acting on the disclination lines and the viscous force determines the fracture behavior.

Recently several papers have been published on the Liénard equation x'' +L x+m x^3+n x^5=0, where the authors studied their explicit solutions and their applications. Here we describe the complete dynamics of these differential equations in the Poincar\'e disc. The Poincar\'e disc is the closed disc centered at the origin of coordinates of radius one, the whole plane R^2 is identified with the interior of this disc, and its boundary, the circle $\sss^1$ is identified with the infinity of R^2.

Recent inference results of the sound velocity in the cores of neutron stars are summarized. Implications for the equation of state and the phase structure of highly compressed baryonic matter are discussed. In view of the strong constraints imposed by the heaviest known pulsars, the equation of state must be very stiff in order to ensure the stability of these extreme objects. This required stiffness limits the possible appearance of phase transitions in neutron star cores. In view of these empirical findings, much discussed issues such as the quest for a phase transition towards restored chiral symmetry and the active degrees of freedom in cold and dense baryonic matter, are explored.

We study the coupling of two topologcal subsystems in distinct topological states, and show that it leads to a precursor behavior of the topological phase transition in the overall system. This behavior is solely determined by the symmetry classes of the subsystem Hamiltonians and coupling terms, and is marked by the persistent existence of subgap states within the bulk energy gap. By investigating the critical current of Josephson junctions involving topological superconductors, we also illustrate that such subgap states play crucial roles in physical properties of nanoscale devices or materials.

We investigate the production of an isolated attosecond pulse (IAP) via the phase-matching gating of high-harmonic generation by intense laser pulses. Our study is based on the integration of the propagation equation for the fundamental and generated fields with nonlinear polarisation found via the numerical solution of the time-dependent Schr\"odinger equation. We study the XUV energy as a function of the propagation distance (or the medium density) and find that the onset of the IAP production corresponds to the change from linear to quadratic dependence of this energy on the propagation distance (or density). Finally, we show that the upper limit of the fundamental pulse duration for which the IAP generation is feasible is defined by the temporal spreading of the fundamental pulse during the propagation. This nonlinear spreading is defined by the difference of the group velocities for the neutral and photoionised medium.