In order to improve contrast and restore color for underwater image captured by camera sensors without suffering from insufficient details and color cast, a fusion algorithm for image enhancement in different color spaces based on contrast limited adaptive histogram equalization (CLAHE) is proposed in this article. The original color image is first converted from RGB color space to two different special color spaces: YIQ and HSI. The color space conversion from RGB to YIQ is a linear transformation, while the RGB to HSI conversion is nonlinear. Then, the algorithm separately operates CLAHE in YIQ and HSI color spaces to obtain two different enhancement images. The luminance component (Y) in the YIQ color space and the intensity component (I) in the HSI color space are enhanced with CLAHE algorithm. The CLAHE has two key parameters: Block Size and Clip Limit, which mainly control the quality of CLAHE enhancement image. After that, the YIQ and HSI enhancement images are respectively converted backward to RGB color. When the three components of red, green, and blue are not coherent in the YIQ-RGB or HSI-RGB images, the three components will have to be harmonized with the CLAHE algorithm in RGB space. Finally, with 4 direction Sobel edge detector in the bounded general logarithm ratio operation, a self-adaptive weight selection nonlinear image enhancement is carried out to fuse YIQ-RGB and HSI-RGB images together to achieve the final fused image. The enhancement fusion algorithm has two key factors: average of Sobel edge detector and fusion coefficient, and these two factors determine the effects of enhancement fusion algorithm. A series of evaluate metrics such as mean, contrast, entropy, colorfulness metric (CM), mean square error (MSE) and peak signal to noise ratio (PSNR) are used to assess the proposed enhancement algorithm. The experiments results showed that the proposed algorithm provides more detail enhancement and higher values of colorfulness restoration as compared to other existing image enhancement algorithms. The proposed algorithm can suppress effectively noise interference, improve the image quality for underwater image availably.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

To obtain an accurate and reproducible experimental results in microbial fuel cell (MFC), it is important to know ‘anode maturation biofilm’ to produce a stable and maximum performance. For this purpose, four single chamber MFCs were tested in this study. The linear sweep voltammetry (LSV) polarization tests illustrated that maximum power densities of three MFCs became stable after 9 weeks. Although there were variations afterwards, such variations were negligible. Average maximum power densities from the 9th to the 17th week were 2,990 mW/m2 (MFC-4), 2,983 mW/m2 (MFC-2), 2,368 mW/m2 (MFC-3) and 837 mW/m2 (MFC-1). Polarization resistance shows that MFC-1 had much larger anode resistance (36.6-85.4 Ω) than the other MFCs (1.7-11.6 Ω). Anodic cyclic voltammetry (CV) shows that current production increased over time and MFC-1 had much smaller current production (24.4 mA) than the other MFCs (31.0-34.9 mA) at 17th week. The increased current production indicates anode biofilm became more mature over time, but overall cell performance did not increased accordingly. Possibly due to the bad inoculation, MFC-1 showed the lowest performance. However, its performance was restored to the initial performance and anode resistance was reduced by 47% at 17th week. This study shows that the optimum anode maturation time is 9 weeks and that bioanode performance is a key factor for MFC performance. This study also shows than LSV polarization and CV tests are accurate and non-destructive measurement methods for diagnosing anode performance.

Improving photobioreactor performance for microalgae cultivation has attracted many researchers over the past years. One of the primary challenges associated with existing photobioreactors is the light penetration. An effective photobioreactor design should maximize light penetration, ensuring uniform illumination throughout the reactor. This study aims to assess the impact of light intensity on microalgal growth from the perspective of energy efficiency and productivity in two photobioreactors. A novel cactus-like and a cylindrical photobioreactor were designed and fabricated using 3D printing technology. These two photobioreactors were used to cultivate two strains of microalgae. The novel photobioreactor achieved a maximum biomass productivity of 0.99 g/L/d and a maximum energy efficiency of 0.3139 g/d/kWh. The cylindrical photobioreactor reached a maximum biomass productivity of 0.74 g/L/d and 0.2199 g/d/kWh of energy efficiency. The increase in biomass productivity can be linked to enhancements in the photobioreactor's surface-to-volume ratio and better light utilization.

The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a serial of PMoA-PWA/ZnO/PVP hybrid films which had different ratio of PMoA/PWA was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer while PMoA/PWA was the chromophore. The photochromic mechanism of PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A3) on A4 paper. Application test showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words and could replace the ordinary paper to realize the reuse of paper.

By planting LEDs on the surfaces of orifice baffles, a novel batch oscillatory baffled photoreactor (OBPR) together with polymer-supported Rose Bengal (Ps-RB) beads are used to investigate reaction kinetics of a photo-oxidation reaction between α-terpinene and singlet oxygen (1O2). In the widely used NMR data analysis for this reaction, α-terpinene and ascaridole are treated as a reaction pair, assuming kinetically singlet oxygen is in excess or constant. We have, for the first time, examined the validity of the method, discovered that increasing α-terpinene initially leads to an increase of ascaridole, indicating that the supply of singlet oxygen is in excess. Applying kinetic analysis, a pseudo first order reaction kinetics is confirmed, supporting this assumption. We have subsequently initiated a methodology of estimating the 1O2 concentrations based on the proportionality of ascaridole concentrations with respect to its maximum under these conditions. With the help of the estimated singlet oxygen data, the efficiency of 1O2 utilization and the photo efficiency of converting molecular oxygen to 1O2 are further proposed and evaluated. We have also identified conditions where further increase of α-terpinene has caused decreases in ascaridole, implying kinetically that 1O2 has now become a limiting reagent, the method of treating α-terpinene and ascaridole as a reaction pair in the data analysis would no longer be valid under those conditions.

Asymmetric lithium salts, such as Lithium (difluoromethanesulfonyl)(trifluoromethanesulfonyl)imide (LiDFTFSI), have been demonstrated to surpass traditional symmetric lithium salts with improved Li+ conductivity and the capacity to generate stable solid electrolyte interphase (SEI) while maintaining compatibility with aluminum (Al0) current collector. However, the intrinsic reductive mechanism through which LiDFTFSI influences battery performance remains unclear and under debate. Herein, the detailed SEI reactions of LiDFTFSI-based electrolytes were investigated by combining density functional theory and molecular dynamics, aiming to clarify the formation process and atomic structure of SEI. Our results show that asymmetric DFTFSI– weakens the interaction between carbonate solvents and Li+, and substantially alter the solvation structure, exhibiting a well-balanced coordination capacity to bis(trifluoromethanesulfonyl)imide (TFSI–). Nanoseconds hybrid molecular dynamics simulation further reveals that the preferential decomposition of LiDFTFSI produces sufficient LiF and Li2O to facilitate a robust SEI. Moreover, the abundant F– generated from LiDFTFSI decomposition accumulates on the Al surface and subsequently combines with Al3+ from the current collector to form AlF3, potentially inhibiting corrosion of the current collector. Overall, these findings elucidate how LiDFTFSI regulates the solvation sheath and SEI structure, advancing the development of high-performance electrolytes compatible with current collector.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

Stimuli-responsive polymeric materials have attracted significant attentions in a variety of high-value-added and industrial applications during the past decade. Among various stimuli, light is of particular interest as a stimulus due to its unique advantages such as precisely spatiotemporal control, mild conditions, ease of use, and tunability. In recent years, a lot of effort toward synthesis of biocompatible and biodegradable polypeptide has resulted in many examples of photo-responsive nanoparticles. Depending on the specific photochemistry, those polypeptide derived nano-assemblies are capable of crosslinking, disassembling, or morphing into other shapes upon light irradiation. In this mini-review, we aim to assess the current state of photo-responsive polypeptide based nanomaterials. First, those “smart” nanomaterials will be categorized by their photo-triggered events (i.e., crosslinking, degradation, and isomerization) which are inherently governed by photo-sensitive functionalities including o-nitrobenzyl, coumarin, azobenzene, cinnamyl, and spiropyran. In addition, the properties and applications of those polypeptide nanomaterials will be highlighted as well. Finally, the current challenges and future directions of this subject will be evaluated.

Sodium-potassium (NaK) liquid alloy is a promising candidate for use as anode material in sodium batteries because of its fluidity, which effectively suppresses the growth of sodium or potassium dendrites. However, the poor wettability of the NaK liquid alloy on conventional metal substrates is unfavorable for cell fabrication due to its strong surface tension. In this paper, low-density and low-cost fluorinated aluminum foam is used as a substrate support material for NaK liquid alloy. By combining low surface tension NaK@C with fluorinated aluminum foam, we obtain a uniformly distributed and structurally stable electrode material. The composite electrode has a cycling stability of more than 3000 hours in a symmetrical cell. Furthermore, when coupled with a sulfurized polyacrylonitrile cathode in carbonate electrolyte, it maintains excellent stability even after 800 cycles, with 72% of capacity retention.

Turbulent flow is the first and fundamental physical phenomena to evaluate when optimising cost and reducing emissions from an Anode Baking Furnace (ABF). Gas flow patterns, velocity field, pressure drop, shear stress, and turbulent dissipation rate variables are the main operational parameters to be optimised, considering a specific geometry. Computational Fluid Dynamics (CFD) allows simulating physical phenomena using numerical methods with computer resources. In particular, the finite element method is one of the most used methods to solve the flow equations. This method requires a discretisation of the geometry of the ABF, called mesh. Hence, mesh is the main input to the finite element method. A suitable mesh for applying a discretisation method determines whether the problem can be simulated or not. Generating an appropriate mesh remains a challenge to perform accurate simulations. In this work, a comparison between meshes generated using two mesh generation tools is presented. Results of different study cases are included.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

We experimentally investigate power-sensitive photo-thermal tuning (PTT) of two-dimensional (2D) graphene oxide (GO) films coated on integrated optical waveguides. We measure the light power thresholds for reversible and permanent GO reduction in silicon nitride (SiN) waveguides integrated with 1 and 2 layers of GO. Raman spectra at different positions of a hybrid waveguide with permanently reduced GO are characterized, verifying the inhomogeneous GO reduction along the direction of light propagation through the waveguide. The differences between the PTT induced by a continuous-wave laser and a pulsed laser are also compared, confirming that the PTT mainly depend on the average input power. These results reveal interesting features for 2D GO films coated on integrated optical waveguides, which are of fundamental importance for the control and engineering of GO’s properties in hybrid integrated photonic devices.

Bio-devices are designed to allow biological matter to perform in vitro almost the same functions it performs in vivo. Therefore, they can benefit from the specificities of such materials and are expected to perform better than traditional devices. On the other hand, the integration of biological material with electronic/electrochemical instrumentation requires careful attention and can produce unconventional results. In this paper, we describe the impedance response of an electrochemical cell that converts sunlight into electrical power. It uses the photosynthetic system known as Reaction Center, which is the core of photosynthesis in several living beings. Under illumination, an abrupt transformation drives the cell electrical response from insulator to conductor and a photocurrent is observed. The impedance spectrum shows a peculiar shape which significantly modifies with the protein activation. It has been analyzed by means of a graphical/analytical/ numerical procedure. The modelling identifies an analogue electrical circuit, whose parameters give quantitative information about the underlying process. Finally, an appropriate normalization of data is proposed which validates data in dark and light and can be useful as a fast screening of measurements.

Optimal conditions for maximum efficacy of photoinitiated polymerization are theoretically presented. Analytic formulas are shown for the crosslink time, crosslink depth and efficacy function. The roles of photoinitiator (PI) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented. For optimal efficacy, a strategy via controlled PI concentration is proposed, where re-supply of PI in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced. Experimental data are analyzed for the role of PI concentration and light intensity on the gelation time and efficacy.

In this research paper a novel Ultra Violet Photo Catalyst Oxidation (UVPCO) sensor for air and surface sanitization using Common Source (CS) amplifier is presented. The ultra violet photo catalysis is the process in which the highly reactive radicals like H+, OH-and peroxides ions are produced from air in the presence of the ultra violet radiation and photo catalyst. In this process, the free radicals outbreaks the bio aerosols like bacteria, fungus and volatile organic compounds (VOCs) and destroy them. The proposed system is relies on the fast operation of PCS which operates under sub-threshold conditions and reduced computation time. The properties of common source amplifier like very high voltage gain and input output resistance increased the sensitivity as well as stability of the circuit. The system is more user friendly and the outcomes of simulation are fairly in agreement with the theoretical estimation. Keywords: bio aerosol, Photo Catalytic Oxidation (PCO), hydroxyl, hydrogen peroxide, SPICE, surface sanitizer.

Li3FeN2 material was synthesized by two-step solid-state method from Li3N (adiabatic camera) and FeN2 (tube furnace) powders. Phase investigation of Li3N, FeN2 and Li3FeN2 were carried out. Discharge capacity of Li3FeN2 is 343 mAh g-1, that is about 44.7% of theoretic capacity. The molar heat capacity of Li3FeN2 at constant pressure in the temperature range 298-900 K should be calculated as Cp,m = 77,831 + 0,130 × T – 6,289 × T-2, where T is absolute temperature, . Thermodynamic characteristics of Li3FeN2 were determined as next: entropy S0298 = 116.2 J mol-1 K-1, molar enthalpy of dissolution ΔdHLFN = ˗ 206,537 ± 2,8 kJ mol−1, the standard enthalpy of formation ΔfH0 = ˗ 291.331 ± 5.7 kJ mol−1, entropy S0298 = 113.2 J mol-1 K-1 (Neumann-Kopp rule) and 116.2 J mol-1 K-1 (W.Herz rule), the standard Gibbs free energy of formation ∆f G0298 = ˗276,7 kJ mol-1.

High-performance anodes are contributed to nanostructure of transition metal oxides for rechargeable Li-ion batteries (LIBs). In this work, we report the fabrication of high-performance anode materials for lithium-ion batteries, MnO2 nanotube directly grown into fabrics of carbon nanofibers, the MnO2/Carbon nanofibers (CNFs) were investigated by X-ray diffraction, scanning and transmission electron microscopies. When tested as the anode material in LIBs, the MnO2/CNFs exhibit superior performance and excellent long cycling performance with a reversible capacity of 835 mA h g-1 at 0.1 A g-1 after the 133 th cycle, a high initial specific capacity of 1094 mA h g-1 at a current density of 0.1 A g-1. The MnO2/CNFs demonstrates notable specific capacities, specifically, with a coulombic efficiency of 99.5 %, both stability and capacity are conspicuously above literature data. These impressive results indicate that MnO2/CNFs has great potential for high-energy and high-power energy storage applications.

Using structured light to drive colloidal motors, due to its advantages of remote manipulation, energy tunability, programmability, and controllability of spatiotemporal distribution, has been attracting much attention in the fields of targeted drug delivery, environmental control, chemical agent detection, and smart device design. Here, we focus on studying the group control of colloidal made from a photo-responsive organic polymer molecule NO-COP (N,O-Covalent organic polymer). These colloidal motors mainly respond to the light intensity patterns. We chose a digital micromirror device (DMD) to modulate the structured light field shining on the sample, by considering its merit of fast refreshing speed, good programmability, and high-power threshold. It is found that under ultraviolet or green light modulation, such colloidal motors exhibit various group behaviors including group diffusion, group patterning, and group migration. The qualitative interpretation is also provided for these observations.

On-chip integration of two-dimensional (2D) materials with unique structures and distinctive properties endow integrated devices with new functionalities and improved performance. With a high flexibility in modifying its properties and a strong compatibility with various integrated platforms, graphene oxide (GO) becomes an attractive 2D material for implementing functional hybrid integrated devices. Here, we demonstrate novel functionalities that go beyond the capabilities of conventional photonic integrated circuits, by harnessing the photo-thermal effects in 2D GO films integrated onto them. These include all-optical control and switching, optical power limiting, and non-reciprocal light transmission. The 2D layered GO films are on-chip integrated with precise control of their thicknesses and sizes. Benefitting from the broadband response of 2D GO films, all the three functionalities feature a very wide operational bandwidth. By fitting the experimental results with theory, we also extract the changes in material properties induced by the photo-thermal effects, which reveal interesting insights about 2D GO films. These results highlight the versatility of 2D GO films in implementing functional integrated photonic devices for a range of applications.

In this study, we investigate the structural changes, electronic properties, and charge redistribution within azo-bithiophene (Azo-BT) chemisorbed monolayers under different light stimuli using density functional theory and molecular dynamics simulations. We consider two types of switches, Azo-BT and BT-Azo, with different arrangements of the Azo and BT blocks counting from the anchor thiol group. The chemisorbed monolayers of pure cis- and trans-isomers with a surface concentration of approximately 2.7 molecules per nm2 are modeled on a gold surface using classical all-atom molecular dynamics. Our results reveal significant shrinkage of the BT-Azo layer under UV illumination, whereas the thicknesses of the Azo-BT layer remain comparable for both isomers. This difference in behavior is attributed to the ordering of the trans-molecules in the layers, which is more pronounced for Azo-BT, leading to a narrow distribution of the inclination angle to the gold surface. Conversely, both layers consisting of cis-switches exhibit disorder, resulting in similar brush heights. To study charge transfer within the immobilized layers, we analyze each snapshot of the layer and calculate mean charge transfer integrals using Nelsen’s algorithm for a number of interacting neighboring molecules. Combining these integrals with reorganization energies defined for the isolated molecules, we evaluate the charge transfer rates and mobilities for electron and hole hopping within the layers at room temperature based on Marcus’ theory. This research offers new perspectives for the innovative design of electrode surface modifications and provides insights into controlling charge transfer within immobilized layers using light triggers. Additionally, we identify molecular properties that are enhanced through specific molecular design, which contributes to the development of more efficient molecular switches for various electronic applications.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

The kinetics and efficacy profiles of photoinitiated polymerization are theoretically presented. For the same dose, lower light intensity achieves a higher steady-state-efficacy (SSE) in type-I; in contrast, type-II has an equal SSE. Higher light intensity has a faster rising efficacy, due to faster depletion of photoinitiator (PS) concentration. However, type-II process is also affected by the available oxygen. Higher light intensity produces more efficient singlet oxygen, resulting a higher transient efficacy, in which all intensities reach the same SSE when oxygen is completely depleted. With external oxygen, type-II efficacy increases with time, otherwise, it is governed only by the light dose, i.e., same dose achieves same efficacy. Moreover, type-II has an efficacy follows Bunsen Roscoe law (BRL), whereas type-I follows non-BRL. The measured type-I efficacy and gelation profile are analyzed by our analytic formulas. Schematics of the photocrosslinking stage defined by the availability of oxygen is developed, where both type-I and –II coexist until the oxygen is depleted. The overall efficacy may be enhanced by resupply of PS or oxygen during the light exposure. The roles of light dose and PS concentration on the efficacy of photoinitiated polymerization should be are governed a new concept of a volume efficacy (Ve), defined by the product of the crosslink (or gelation) depth (CD) and local [efficacy].

In this research work, we describe the preparation process, characterization, and photo-physical studies of an ionic liquid (IL) based semiconductor Zinc Oxide (ZnO) nanoparticles synthesized by an economical wet chemical precipitation method. For the first time, an IL was synthesized with the help of a chemical reaction between triethylamine (TEA) and bromoacetic acid (BAA). A polyamide dye was prepared by a reaction between two monomers, ethylenediamine (EDA) and trimesoylchloride (TMC), under room temperature conditions. The polyamide dye was capped on ZnO nanoparticles, and the final product was divided into three different samples, A, B, and C, according to level of concentrations of IL and Polyamide dye. These samples were characterized with X-Ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Dynamic Light Scattering (DLS) spectra, Ultraviolet-Visible (UV-Vis), and Fluorescence spectroscopies. The formation of polyamide linkages in the ionic liquid has been confirmed by a spectroscopic method using Fourier Transform Infrared (FTIR) spectroscopy. The capping of polyamide dye molecules on the surface of ZnO nanoparticles revealed two things: (i) improved UV absorption spectra and (ii) enhanced luminescence in the photoluminescence spectra. Hence, during investigations, broad absorption bands were observed at peaks 263 nm, 278 nm, and 276 nm respectively for samples A, B, and C. Further, IL was used as an electrolyte or redox mediator and polyamide as a dye material in the fabrication of ZnO Dye-Sensitized Solar Cells (DSSCs). The samples A, B, and C were used in the fabrication of photo-anode assemblies for ZnO DSSCs. The ZnO DSSCs were tested under strong simulated light at Air Mass (AM) 1.5 solar irradiations. The observed photovoltaic results shown that solar cell SCB generated a maximum power conversion efficiency (η) of 5.65%, higher than the power conversion efficiencies of solar cells SCA (3.99%) and SCC (4.46%) respectively. The Incident Photon to Current Conversion Efficiency (IPCE) spectra values of ZnO DSSCs shown a significant improvement in the incident photon to current conversion efficiency of solar cell SCB (IPCE=61%) as compared to SCC (enhanced by 6%) and SCA (enhanced by 4%). Such solar cell assemblies can be suitable for green and clean energy applications.

Silicon-based photoelectrochemical (PEC) conversion system has recently gained attention with its ability to provide cost-efficient and superior photoresponsive behavior in regard to other various semiconductor photoelectrodes. Carbon-based co-catalysts have always shared the spotlight for being rendered as alternative metal-free electrocatalysts intended for hydrogen evolution reaction (HER). In particular, a representative carbon-derived material, reduced Graphene Oxide (rGO) has attracted much attention as a non-metal catalyst for efficient and durable HER. Herein, we have deposited rGO on silicon nanowire (SiNW) structure which shows the highest reduction in the overpotential for HER up to date. This could be attributed to the synergistic effects of rGO and SiNW with unique anisotropic morphology, facile tuning capabilities, and scalable fabrication methods. Combined with nanostructured photocathode, rGO deposited SiNW showed better applied bias photon to current conversion efficiency of 3.16%, which is 158 times higher than that of bare planar Si system. In regard to this development we believe that rGO-SiNW photoelectrodes would pave the way for state-of-the-art highly efficient non-metal catalysts for energy conversion technologies.

The primary goal of this review is to provide a comprehensive overview of the state-of-the-art in solid-state batteries (SSBs), with a focus on recent advancements in solid electrolytes and anodes. The paper begins with a background on the evolution from liquid electrolyte lithium-ion batteries to advanced SSBs, highlighting their enhanced safety and energy density. It addresses the increasing demand for efficient, safe energy storage in applications like electric vehicles and portable electronics. A major part of the paper analyzes solid electrolytes, key to SSB technology. It classifies solid electrolytes as polymer-based, oxide-based, and sulfide-based, discussing their distinct properties and application suitability. The review also covers advancements in anode materials for SSBs, exploring materials like lithium metal, silicon, and intermetallic compounds, focusing on their capacity, durability, and compatibility with solid electrolytes. It addresses challenges in integrating these anode materials, like interface stability and lithium dendrite growth. This review includes a discussion on the latest analytical techniques, experimental studies, and computational models to understand and improve the anode-solid electrolyte interface. These are crucial for tackling interfacial resistance and ensuring SSBs' long-term stability and efficiency. Concluding, the paper suggests future research and development directions, highlighting SSBs' potential in revolutionizing energy storage technologies. This review serves as a vital resource for academics, researchers, and industry professionals in advanced battery technology development. It offers a detailed overview of materials and technologies shaping SSBs' future, providing insights into current challenges and potential solutions in this rapidly evolving field.

Electrode is a key component in a microbial electrolysis cell (MEC) and it needs significant improvement for practical implementation of MEC. For effective development of electrode technology, accurate and reproducible analytical methods are very important. Linear sweep voltammetry (LSV) is an essential analytical method for evaluating electrode performance; however, it has not been firmly established yet in the MEC field. In this study, biological brush (BB), abiotic brush (AB), Pt wire (PtW), stainless steel wire (SSW) and mesh (SSM)) were tested to explore the most suitable counter electrode in different medium conditions. Coefficient of variation (CV) for Imax of LSV were comparatively analyzed. In BB-anode LSV, SSW (0.48%) and SSM (2.17%) showed higher reproducibility as a counter electrode. In SSM-cathode LSV, BB (1.76%) and PtW (2.01%) produced more reproducible results. In the Ni-AC-SSM-cathode LSV, PtW (3.54%) and BB (8.81%) produced more reproducible result. It shows electrode used in the operation is an appropriate counter electrode in the acetate-added condition. However, in the absence of acetate, PtW (1.24%) and BB (1.71%) produced more reproducible results in SSM cathode and PtW (0.61%) and SSW (1.21%) did in the Ni-AC-SSM-cathode, showing PtW is an appropriate counter electrode. These results also shows that PtW is an appropriate counter electrode in cathode LSV.

Herpes simplex virus (HSV) infections can be treated with direct acting antivirals like acyclovir and foscarnet, but long-term use can lead to drug resistance, which motivates research into broadly-acting antivirals that can provide a greater genetic barrier to resistance. Photodynamic inactivation (PDI) employs a photosensitizer, light, and oxygen to create a local burst of reactive oxygen species that inactivate microorganisms. The botanical plant extract Orthoquin^TM is a powerful photosensitizer with antimicrobial properties. Here we report that Orthoquin also has antiviral properties. Photoactivated Orthoquin inhibited herpes simplex virus type 1 (HSV-1) and herpes simplex virus type 2 (HSV-2) infection of target cells in a dose-dependent manner, across a broad range of sub-cytotoxic concentrations. HSV inactivation required direct contact between Orthoquin and the inoculum, whereas pre-treatment of target cells had no effect. Orthoquin did not cause appreciable damage to viral capsids or pre-mature release of viral genomes as measured by qPCR for the HSV-1 genome. By contrast, immunoblotting for HSV-1 antigens in purified virion preparations suggested that higher doses of Orthoquin had a physical impact on certain HSV-1 proteins that altered protein mobility or antigen detection. Orthoquin PDI also inhibited the non-enveloped adenovirus (AdV) in a dose-dependent manner, whereas Orthoquin-mediated inhibition of the enveloped vesicular stomatitis virus (VSV) was light-independent. Together, these findings suggest that broad antiviral effects of Orthoquin-mediated PDI may stem from damage to viral attachment proteins.

Following the occurrence of a typhoon, quick damage assessment related to residents can facilitate quick dispatch of house repair and disaster insurance works. Employing a deep learning method, this study used aerial photos of the Chiba prefecture obtained following the Typhoon Faxai in 2019 to automatically detect and evaluate the roof damage. This study comprised three parts: training deep learning model, detecting the roof damage using trained model, and classifying the level of roof damage. The detection object comprised roof outline, blue tarps, and roof completely destroyed. The roofs were divided into three categories: roof without damage, roof with blue tarps and roof completely destroyed. the F value obtained using the proposed method was higher than those obtained using other methods. In addition, it can be further divided into 5 levels from level 0 to 4. Finally, the spatial distribution of the roof damage was analyzed using ArcGIS tools. The proposed method is expected to provide certain reference for the real-time detection of the roof damage after the occurrence of a typhoon.

Lithium batteries and an increasing focus on CO₂ reduction have become an integral part of daily life and business for many people. Boron and boron compounds have been widely studied together in the history and development of lithium batteries. With a broad examination of battery components and systems but a boron-centric approach to raw materials, this review seeks to summarize past and recent studies on the following: which boron compounds are studied in lithium battery, in which parts of lithium batteries, what improvements are offered for battery performance, and what improvement mechanisms can be explained. The uniqueness of boron and its extensive application beyond batteries contextualizes the interesting similarity with studies on batteries. The paper predominantly focuses on lithium-ion batteries (LIBs) but also mentions other lithium batteries. At the end, the article aims to predict prospective trends for future studies that may lead to the successful and extensive use of boron compounds on a commercial scale.

Electric vehicles (EVs) are being endorsed as the uppermost successor to fuel-powered cars, with timetables for banning the sale of petrol-fueled vehicles announced in many countries. However, the range and charging times of EVs are still considerable concerns. Fast charging could be a solution to consumers' range anxiety and the acceptance of EVs. Nevertheless, it is a complicated and systematized challenge to realize the fast charging of EVs because it includes the coordinated development of battery cells, including electrode materials, EV battery power systems, charging piles, electric grids, etc. This paper aims to serve as an analysis for the development of fast-charging technology, with a discussion of the current situation, constraints and development direction of EV fast-charging technologies from the macroscale and microscale perspectives of fast-charging challenges. It is emphasized that to essentially solve the problem of fast charging, the development of new battery materials, especially anode materials with improved lithium ion diffusion coefficients, is the key. It is highlighted that red phosphorus is the most promising anode that can simultaneously satisfy the double standards of high-energy density and fast-charging performance to a maximum degree.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

Porous MnO/C microspheres have been successfully fabricated by a fast co-precipitation method in a T-shaped microchannel reactor. The structures, compositions and electrochemical performances of the obtained MnO/C microspheres are characterized by X-ray diffraction, emission scanning electron microscopy, transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller analysis, charge-discharge testing, cyclic voltammograms, and electrochemical impedance spectra. Experimental results reveal that the as-prepared MnO/C, with a specific surface area of 96.66 m²·g^–1 and average pore size of 24.37 nm, exhibits excellent electrochemical performance, with a discharge capacity of 655.4 mAh·g^–1 after cycling 50 times at 1 C and capacities of 808.3, 743.7, 642.6, 450.1, and 803.1 mAh·g^–1 at 0.2, 0.5, 1, 2, and 0.2 C, respectively. Moreover, the controlled method of using a micro-channel reactor, which can produce larger specific surface area porous MnO/C with improved cycling performance by shortening lithium-ion diffusion distances, can be easily applied in real production on a large-scale.

In fuel-cell technological development, one of the most important objectives is to minimize the amount of Pt, the most employed material as oxygen reduction and methanol oxidation electro-catalyst. In this paper we report the synthesis and characterization of Te nanotubes (TeNTs) decorated with Pt nanoparticles, readily prepared from stirred aqueous solutions of PtCl2 containing a suspension of TeNTs and ethanol acting as a reducing agent, avoiding the use of any hydrophobic surfactants as capping stabilizing substance. The as obtained TeNTs decorated with Pt nanoparticles (TeNTs/PtNPs) have been fully characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area diffraction patterns (SAD), X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV). We demonstrate that the new material can be successfully employed in fuel cell either as anodic (for methanol oxidation reaction) and cathodic (for oxygen reduction reaction) electrode with high efficiency in terms of related mass activities and on-set improvement. Remarkably, the cell operates in aqueous electrolyte buffered at pH 7.0, thus avoiding acidic or alkaline conditions that may lead e. g. to Pt dissolution (at low pH) and paving the way for the development of biocompatible devices and on chip fuel cells.

The Ce0.5Y0.35Tb0.15F3 nanoparticles with CeF3 hexagonal structure were synthesized by co-precipitation technique. The average nanoparticle diameter was 14±1 nm. The luminescence decay curves of Ce0.5Y0.35Tb0.15F3 nanoparticles (λem = 541 nm, 5D4 – 7F5 transition of Tb3+) conjugated with Radachlorin by means of polyvinylpyrrolidone coating as well as without Radachlorin were detected. Efficient nonradiative energy transfer from Tb3+ to the Radachlorin was demonstrated. The maximum energy transfer coefficient for nanoparticles conjugated with Radachlorin via polyvinylpyrrolidone and without the coating were 82% and 55%, respectively. The average distance between nanoparticle surface and Radachlorin was R0 =4.5 nm. The best results for X-ray induced cytotoxicity was observed for NP-PVP-Rch sample at the lowest Rch concentration. In particular, after X-ray irradiation the survival A 549 human lung carcinoma cells decreased by ~12%.

In a world where conventional sources of energy are fast depleting, the quest for alternative energy sources may hold the key for the survival of humanity. In the present work, emphasis has been given to the idea of producing energy from perovskite based solar cells. In order to bring this idea into fruition, a unique and novel nano structured perovskite material n-propyl ammonium lead chloride (C₃H₇NH₃⁺PbCl₃⁻) was prepared through a unique co-precipitation route using n-propyl amine (n-C₃H₇NH₂) and hydrochloric acid as the starting precursors with aqueous solution of Pb(CH₃COO)₂3H₂O. Finally acetic acid was added to the solution and this solution was allowed to concentrate and then gradually cooled down to room temperature. After math, the synthesized material was spin-coated on TiO₂ film to fabricate the solar cell. The device was then undergone systematic analysis using XRD, SEM, UV and Photo Conversion to get a transparent idea regarding its structural, electrical and optical properties. When experimentally applied, this perovskite-based solar cell has shown energy conversion efficiency (η) of around 6.01 % which is noticeably good. Thus it can be concluded that this material is promising for fabrication of vastly efficient solar cells. This technology can be tried in large scale as an alternative of conventional energy in the near future.

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of their electrode materials. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to the advantages of high flexibility and bendability. However, it is still a big challenge to realize 1D flexible fiber lithium-ion batteries with excellent electro-chemical properties and good mechanical performance. In this work, a reduced graphene ox-ide-based printing ink is proposed to fabricate flexible Li4Ti5O12/graphene fiber electrodes through a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce graphene oxide in one step, which improved the conductivity of the fiber elec-trode. Furthermore, a 3D conductive network is constructed inside the fiber electrodes due to the high specific surface area of reduced graphene oxide, which enhances the electronic conductivity and ion mobility. The fiber electrode not only has good mechanical performance, but also has ex-cellent electrochemical properties. Equally important, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of fu-ture flexible electronic devices.

A Invasive emerging pollutants from wastewater effluent discharge, such as dyes, pesticides, etc., pose a serious threat to the ecosystem. Advanced oxidation processes (AOPs) under visible light irradiation have emerged as a promising technology to overcome toxic and recalcitrant organic compounds. In this work, the impact of operational factors, including the concentration of Fe3+ or Fe2+, [H2O2], the molar ratio (Oxalate/ Fe3+ or Fe2+), and the initial pH, was studied to obtain high efficiency in the degradation and mineralization of such a food dye to reduce their pollution. The study deals with the comparison of the efficiency of UV, LED, and sunlight irradiation on the photocatalytic degradation of the dye using Fe3+/Lig and Fe2+/Lig complexes. The results showed that sunlight irradiation gave a very rapid kinetic and higher degradation efficiency of over 70%. The optimized conditions for the maximum elimination of the dye with a photocatalytic degradation efficiency (98%) and a mineralization rate of 96% were obtained with the Fe3+/Lig complex, based on the Box Benhken surface design analysis. In the presence of H2O2, the degradation reached an equilibrium stage after 15 min (97.57%) for the Fe(III)/Lig system. Moreover, the inhibition effect of inorganic ions on the photo-Fenton performance of Fe3+/Lig and Fe2+/Lig was studied. The study suggests that the use of nanocrystals of hematite as a Fenton reagent for treating textile effluents needs further investigation. The results showed that the proposed models were well-suited to batch treatment under sunlight. This study not only proposes a Fe3+/Lig and Fe2+/Lig system for the elimination of a food dye without adjusting the pH of the medium, but it also provides insight into the best source of light irradiation for the photocatalytic degradation process.

In this paper, mesoporous electrodes consisted of Sb-doped SnO2 deposited onto Ti plates controlled corroded under acidic medium were synthesized by spin-coating method, and morpho structurally characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrodes were electrochemical testing in the degradation/mineralization by electrooxidation (EO) of doxorubicin (DOX) as single-component and multi-component together with capecitabine (CCB)-from cytostatic class and humic acid (HA)-from natural organic matter (NOM) class in the absence/the presence of activated carbon (AC) as particulate electrode. The best mineralization efficiency of 67 % was achieved for DOX mineralization using Sb-doped SnO2 deposited onto Ti plate controlled corroded with oxalic acid in electrooxidation process. The presence of AC within the electrolysis process generated a synergy effect of 52.75 % for TOC parameter removal, which is in accordance and quite better than the result reported in the literature. The aspects related to the complex mechanism of DOX degradation and mineralization are discussed. The superiority of AC assisted electrooxidation, as electrochemical filtering (EF), was proved considering simultaneous degradation and mineralization of mixture of doxorubicin, capecitabine and humic acid.

To mitigate lithium dissolution and polysulfide shuttle effect phenomena in high energy lithium sulfur batteries (LISBs), a conductive, flexible, and easily modified polymer composite layer was applied on the anode. The polymer composite layer includes polyaniline and functionalized graphite. The electrochemical behavior of LISBs was studied by galvanostatic charge/discharge tests from 1.7 to 2.8 V up to 90 cycles and via COMSOL Multiphysics simulation software. No apparent overcharge occurred during the charge state, which suggests that the shuttle effect of polysulfides was effectively prevented. The COMSOL Multiphysics simulation provides a venue for optimal prediction of the ideal concentration and properties of the polymer composite layer to be used in the LISBs. The testing and simulation results determined that the polymer composite layer diminished the amount of lithium polysulfide species and decreased the amount of dissolved lithium ions in the LISBs. In addition, the charge/discharge rate of up to 2.0 C with a cycle life of 90 cycles was achieved. The knowledge acquired in this study was important not only for the design of efficient new electrode materials, but also for understanding the effect of the polymer composite layer on the electrochemical cycle stability.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

The low relative humidity (RH) levels in a greenhouse during the daytime in a strawberry (Fragaria × ananassa Duch) cultivation period negatively affect the growth of strawberry related to photo-physiology. Therefore, this study was conducted to confirm an efficient RH management method by analyzing the phenotypic characteristics related to photo-physiology by controlling the RH in a greenhouse during the daytime with a fog system. Strawberry plants were grown respectively in a greenhouse affected by natural RH changes (control) and in a greenhouse with 40% ~ 50% RH adjusted during the daytime using a fog system. In the greenhouse, with controlled RH, the temperature decreased, and the RH was higher in the initial growth stage of strawberry planting than the control. It was observed a significant increase in the survival rate of the strawberry plant, as well as the incidence of powdery mildew, was lowered. In addition, the photosynthetic rate and OJIP chlorophyll a fluorescence transients related to photosystem II efficiency of strawberry leaves were significantly higher in the fog treatment than in the control. In winter, during the day, the number of days on which the temperature dropped below 20℃ has increased, the greenhouse temperature with controlled RH was lower due to the fog system. When the yield per strawberry plant in January and February was investigated, the control was higher than the RH treatment. Therefore, RH management using a fog system must be controlled at a level where a temperature range is adequate for plant growth, in which the efficient control of these parameters increases strawberry productivity.

Biopolymers are of growing interest, but to improve some of their poor properties and performance, it is required the formulation of bio-based blends and/or adding of nanoparticles. For this purpose, in this work, two different metal oxides, such as zinc oxide (ZnO) and titanium dioxide (TiO2), at different concentrations (0.5, 1 and 2 %wt.) have been added in polylactic acid (PLA) and polylactic acid/polyamide 11 (PLA/PA11) blends to establish their effects on solid-state properties, morphology, melt behaviour, and photo-oxidation resistance. It seems that the addition of ZnO in PLA leads to a significant reduction of its rigidity probably due to an inefficient dispersion in the melt state, while the addition of TiO2 does not penalise PLA rigidity. Interestingly, the addition of both ZnO and TiO2 in PLA/PA11 blend has a positive effect on the rigidity because of blend morphology refinement and leads to a slight increase in film hydrophobicity. The photo-oxidation resistance of neat PLA and PLA/PA11 blend is significantly reduced due to the presence of both metal oxides, and this must be considered when designing the potential applications. The last results suggest that both metal oxides could be considered as photo-sensitive degradant agents for biopolymer and biopolymer blends.

Despite chronic fibrosis and associated excess extracellular matrix (ECM) deposition and crosslinking occurring in many pathological conditions, few in vitro studies examine how fibrosis-induced ECM stiffening impacts lymphatic endothelial cells (LEC) behavior and subsequent new lymphatic vessel growth and function. This study examined the stiffening profile of PhotoCol®—commercially available methacrylated type I collagen—photo-crosslinked with photoinitiators Lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP), Irgacure 2959 (IRG), and Ruthenium/Sodium Persulfate (Ru/SPS) prior to evaluating PhotoCol® permeability and LEC response to PhotoCol® at low and high stiffness levels representing normal and fibrotic ECM stiffness. Ru/SPS produced the highest maximum stiffness for photo-crosslinked PhotoCol® hydrogels. While Ru/SPS stiffness values did not differ significantly with increased light exposure, permeability decreased significantly with increasing light exposure for 40 kDa dextran. Finally, LECs on softer PhotoCol® appeared smaller with less prominent VE-Cadherin (cell-cell junction) and F-actin expression compared to cells on stiffer PhotoCol®. Overall, PhotoCol® with Ru/SPS photoinitiator provides the fibrillar microstructure and dynamic stiffness range that enables systematic study of LEC stiffness responses relevant to the stiffened ECM observed in pathologies with significant fibrotic activity. Therefore, this study demonstrates the utility of PhotoCol® with Ru/SPS for disease modeling applications, particularly modeling lymphatic vascular growth and function during fibrosis.

Dendrite growth and parasitic reactions with liquid electrolyte are the two key factors that restrict the practical application of the lithium metal anode. Herein, a bis(benzene sulfonyl)imide based single-ion polymer artificial layer for lithium metal anode is successfully constructed, which is prepared via blending the as-prepared copolymer of lithiated 4, 4’-dicarboxyl bis(benzene sulfonyl)imide and 4,4’-diaminodiphenyl ether on the surface of lithium foil. This single-ion polymer artificial layer enables compact structure with unique continuous aggregated Li+ clusters, thus reducing the direct contact between lithium metal and electrolyte, and ensuring Li+ transport fast and homogeneous simultaneously. Based on which, the coulombic efficiency of the Li|Cu half-cell is effectively improved, and the cycle stability of the Li|Li symmetric cell can be prolonged from 160 h to 240 h. Surficial morphology and elemental valence analysis confirm that the bis(benzene sulfonyl)imide based single-ion polymer artificial layer effectively facilitates the Li+ uniform deposition and suppresses parasitic reactions between lithium metal anode and liquid electrolyte in the LFP|Li full-cell. This strategy provides a new perspective to achieve steady lithium metal anode, which can be a promising candidate in practical application.

Exsolved perovskites can be obtained from lanthanum ferrites, such as La0.6Sr0.4Fe0.8Co0.2O3, as result of Ni doping and thermal treatments. Ni can be simply added to the perovskite by an incipient wetness method. Thermal treatments include calcination in air (e.g., 500 °C) and subsequent reduction in diluted H2 at 800 °C to favor the exsolution process. The chemistry of the nanoparticles exsoluted on the substrate surface can be further modulated by a post treatment in air. These processes allow to produce a two-phase material consisting of a Ruddlesden-Popper type structure and a solid oxide solution e.g. α-Fe100-y-zCoyNizOx oxide. The formed electro-catalyst shows sufficient electronic conductivity under reducing environment at the SOFC anode. Outstanding catalytic properties are observed for the direct oxidation of dry fuels in SOFCs, including H2, methane, syngas, methanol, glycerol and propane. This anode electrocatalyst can be combined with full density electrolyte based on Gadolinia-doped Ceria or with La0.8Sr0.2Ga0.8Mg0.2O3 (LSGM) or BaCe0.9Y0.1O3-δ (BYCO) to form a complete perovskite structure-based cell. Moreover, the exsolved perovskite can be used as a coating layer or catalytic pre-layer of a conventional Ni-YSZ anode. Beside the excellent catalytic activity, this material also shows proper durability and tolerance to sulphur poisoning. In this mini review, preparation methods, physico-chemical characteristics, surface properties of exsoluted and core-shell nanoparticles encapsulated on the metal-depleted perovskite substrate surface, electrochemical properties for the direct oxidation of dry fuels and related electrooxidation mechanisms are examined and discussed.

Li₂TiO₃ nanopowders were synthesized by hydrothermal process using anatase TiO₂ and LiOH H₂O as raw materials. Li₂TiO₃ crystallizes in the layered monoclinic structure (space group C2/c) with average crystallite size of 34 nm. Morphology, elemental composition and local structure of products were carried out using HRTEM, FESEM, EDS, Raman and FTIR spectroscopy. Transport properties investigated by d.c. (4-probe measurements) and a.c. (complex impedance spectroscopy) show the activation energy of 0.71 and 0.65 eV, respectively. The ionic transport properties of Li⁺ ions in nanocrystalline Li₂TiO₃ characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) validate the good electrochemical properties of this anode material for lithium-ion batteries.

As a photo-catalytic titanium oxide film deposition process, thermal spray is hoped to be utilized practically on the condition that it is relatively easy to deposit anatase rich films. However, because of its high equipment and feedstock powder costs, it is very difficult to introduce thermal spray equipment into small companies. In this study, to develop a low cost thermal spray system, low power atmospheric suspension plasma spray equipment with titanium hydroxide suspension created by hydrolysis of titanium tetra iso butoxide using Ar, N2 as working gases. For avoiding sedimentation of the hydroxide particles in the suspension, mechanical milling of the suspension was conducted to create colloidal suspension before using it as feedstock. Moreover, an Ultrasonic wave container was used to keep the suspension particles moving while the spray process was conducted. After the film deposition, with As for the coating, anatase rich TiO2 film could be obtained. For characterization of the film, microstructure observation by optical microscope and X-ray diffraction was carried out. Consequently, by creation of colloidal suspension, deposition could be conducted without sedimentation of the hydroxide particle in the suspension during operation. Besides, it was proved the film had enough photo-catalytic property to decolor methylene-blue droplet

The growing interest in Na-ion batteries as a “beyond lithium” technologies for energy storage drives the research for high-performance and environment-friendly materials. Na2Ti3O7 (NTO) as an eco-friendly, low-cost anode material shows a very low working potential of 0.3 V vs Na+/Na but suffers from poor cycling stability, which properties can be significantly influenced by materials synthesis and treatment. Thus, in this work, the influence of the calcination time on the electrochemical performance and the reaction mechanism during cycling were investigated. NTO heat-treated for 48 h at 800 °C (NTO-48h) demonstrated enhanced cycling performance in comparison to NTO heat-treated for only 8 h (NTO-8h). The pristine material was thoroughully characterized by X-ray diffraction, laser granulometry, X-ray photoelectron spectroscopy, and specific surface area measurements. The reaction mechanisms induced by sodiation/desodiation and cycling were investigated by opernado XRD. Electrochemical impedance spectroscopy was used to evidence the evolution of the solid electrolyte interface layer (SEI) and modification of charge transfer resistances as well as the influence of cycling on capacity decay. The evolution of the crystallographic structure of NTO-48h revealed a more ordered structure and lower surface contamination compared to NTO-8h. Moreover, the residual Na4Ti3O7 phase detected after the sodium extraction step in NTO-8h seems correlated to the lower electrochemical performance of NTO-8h compared to NTO-48h.

Knowledge on the health of banana trees is critical for farmers to profit from banana cultivation. Fusarium wilt and banana blood diseases (BDB), two significant diseases infecting banana trees, are caused by Fusarium oxysporum and Ralstonia syzygii, respectively. They have successfully caused a decline in crop yield as they destroy the trees, starting sequentially from the pseudostem to the fruits. The entire distribution of BDB and Fusarium on a plantation can be understood using advanced geospatial information obtained from multispectral aerial photographs taken using an unmanned aerial vehicle (UAV), combined with the reliable data field of infected trees. Vegetation and soil indices derived from a multispectral aerial photograph, such as normalized difference vegetation index, modified chlorophyll absorption ratio index, normalized difference water index (NDWI) and soil pH, may have to be relied on to explain the precise location of these two diseases. In this study, a random forest algorithm was used to handle a large dataset consisting of two models: the banana diseases multispectral model and the banana diseases spectral model. The results show that the soil indices, soil pH and NDWI are the most important variables for predicting the spatial distribution of these two diseases. Simultaneously, the plantation area affected by BDB is more extensive than that affected by Fusarium, if the variation of planted banana cultivars is not considered.

To address the limitations of the current anodes of Li+-ion batteries (LIBs), a Ge/GeO2/Carbon (Ge@GeO2-C) composite was designed by introducing a high-energy ball-milling process for advanced LIBs. Ge@GeO2-C is prepared and characterized by XPS, XRD, SEM, and TEM, which facilitate synthesis and provide controllability with respect to milling time. Interestingly, as the ball-milling time increased, the proportion of metallic Ge increased during the carbon thermal reduction reaction. The electrochemical characteristics of Ge@GeO2-C are assessed using differential capacity analysis (dQ/dV) and galvanostatic charge-discharge techniques to confirm its viability as an anode material in LIBs. The results demonstrated decent initial and secondary capacities of approximately 1800 mAh g-1 (for the first cycle) and 838 mAh g-1 (for the second cycle) at a rate of C/60 by the reaction between Ge and the Li-Ge complex. Furthermore, postmortem characterization was performed to gain an understanding of the material, suggesting future prospects for advanced LIBs.

Silicon has a theoretical specific capacity of 4200 mAh g−1, which is considered to have significant potential for anode materials in lithium-ion batteries (LIBs). However, the volume change that occurs in silicon during charging and discharging affects the development of commercial applications. In this work, a yolk-shell structured Si@void@C anode material has been developed to address this problem. The silicon nanoparticle yolk material is obtained by recycling kerf-loss (KL) Si waste from the photovoltaic industry, the carbon shell is prepared via a hydrothermal process with glucose, and the sacrificial interlayer is Al2O3. The synthesized material is used to fabricate anodes that show a high reversible capacity of 836 mAh g−1 at the current density of 0.1 A g−1 after 100 cycles, with a Coulomb efficiency of 71.4%. This work demonstrates a relatively low-cost approach to turn KL Si waste into value-added materials for LIBs.

Li4Ti5O12 (LTO) exhibits zero-strain behavior, exceptional cycle stability, low cost, and high safety. However, it is still low in electronic and ionic conductivity. Incorporating Sn into LTO materials can increase electronic conductivity and specific capacity. However, Sn still experiences volumetric expansion during the charging/discharging process. Adding activated carbon (AC) into the LTO/Sn composite can help improve the expansion resistance and electronic conductivity. In this work, the AC was first synthesized from charcoals through the carbon activation process and mixed with LTO precursors through the sol-hydrothermal method followed by mixing with Sn through the mechanochemical process to produce LTO@AC/Sn composites. The Sn content was fixed at 15 wt.%, while the AC contents were varied at 1 wt.%, 3 wt.%, and 5 wt.%. The AC specific surface area is increased by more than 100% compared to the non-activated one. The best effects of AC on grain morphology and distribution were found in the LTO/Sn contained 3 wt.% of AC, leading to transfer resistance, ohmic resistance, specific capacity, and coulombic efficiency were found to be 48.1 Ω, 8.5 Ω, 138 mAhg-1, and near 100%, respectively. The result suggests that the LTO@AC/Sn could be a favorable anode active material in lithium-ion batteries.

Ammonia produced using renewable hydrogen is being viewed as a promising media for the export of energy from locations rich in renewable energy sources. Solid oxide fuel cells (SOFCs) are efficient devices for converting such exported ammonia back into electricity at the point of use, however investigations on materials and operating regime for direct ammonia fuelled SOFCs are limited. The studies on fuel electrodes tailored specifically for ammonia fuel are limited. In this work, we evaluated the direct ammonia SOFC performance with Silver-Lanthanum Strontium Cobalt Ferrite (Ag-LSCF) composite anode and a novel Palladium (Pd) nanoparticle decorated Silver-Lanthanum Strontium Cobalt Ferrite (Pd-Ag-LSCF) composite anode in the temperature range of 500 °C to 800 °C. It is hypothesized that Palladium nanoparticles in the anode provide hydrogen dissolution and shift the ammonia decomposition reaction towards the right. The cell performance was evaluated with both hydrogen and ammonia as fuels and a clear-cut improvement in the performance was observed with the addition of Pd for both the fuels. The results showed a performance enhancement by 20% and 43% with hydrogen and ammonia fuels respectively from the Pd addition of Ag-LSCF anode. Open circuit voltage (OCV) values of the cells with hydrogen and ammonia fuel recorded over the temperature range of 500 °C to 800 °C indicated the possibility of direct electro-oxidation of ammonia in SOFCs.

To characterize the mechanisms by which the highly-conserved exocyst trafficking complex regulates eye physiology in zebrafish and mice, we focused on exoc5 (aka sec10), a central exocyst component. We analyzed both exoc5 zebrafish mutants and retinal pigmented epithelium (RPE)-specific Exoc5 knockout mice. Exoc5 is present in both the non-pigmented epithelium of the ciliary body and in the RPE. In this study we set out to establish an animal model to study the mechanisms underlying the ocular phenotype and to establish if loss of visual function is induced by postnatal RPE Exoc5-deficiency. Exoc5-/- zebrafish showed smaller eyes, with decreased number of melanocytes in the RPE and shorter photoreceptor outer segments. At 3.5 days post fertilization, loss of rod and cone opsins were observed in zebrafish Tg:exoc5 mutants. Mice with postnatal RPE-specific loss of Exoc5 showed retinal thinning associated with compromised visual function, and loss of visual photoreceptor pigments. This retinal phenotype in Exoc5-/- mice was present at 20-weeks, and the phenotype was more severe at 27-weeks, indicating progressive disease phenotype. We previously showed that the exocyst is necessary for photoreceptor ciliogenesis and retinal development. Here, we report that exoc5 mutant zebrafish and mice with RPE-specific genetic ablation of Exoc5 develop abnormal RPE pigmentation, resulting in retinal cell dystrophy and loss of visual pigments associated with compromised vision. As RPE cells are “downstream” of photoreceptor cells in the visual process, these data suggest exocyst-mediated retrograde communication and dependence between the RPE and photoreceptors.

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

In this paper, a new anode environmentally friendly for hydrogen production was developed based on 430 stainless steel with an electrodeposited cobalt layer. The novelty of this work is the cobalt source once the electrodeposition bath was obtained from recycling of spent Li-ion batteries cathode with composition LiCoO₂. The electrodeposited cobalt behaves as supercapacitor in KOH 1M. In the linear voltammetry in KOH 1M, when the overpotential reaches 370 mV, the anodic density current for 430 SS/Co is 19 mA cm⁻². Thus, the anode developed in this paper achieves the double of density current with half of production cost if compared with 316SS. Moreover the anode construction described in this paper is an excellent option for Li- ion battery recycling.

In the last decades, numerous studies indicated the substantial role semiconductors could play in photocatalytic processes for environmental applications. Materials that contain a semi-conductor as a photo-catalyst have a semi-permanent capacity for removing harmful gases from the ambient air. In the present work, the focus is on TiO2. Heterogeneous photo-catalysis using TiO2 leads to the degradation of NO/NO2, benzene, toluene, and other priority air pollutants once in contact with the semiconductor surface. Preliminary evidence indicates that TiO2 containing construction materials and paints efficiently destroy the ozone precursors NO and NO2 up to 80% and 30%, respectively. Therefore, the development of innovative coatings containing TiO2 as a photo-catalyst was in the foreground of research activities with the aim to be used as building and construction materials mainly outdoors, e.g. on building facades in high traffic roads for the degradation of priority air pollutants (NOx and volatile organic compounds) in the polluted urban atmosphere. Though the advantages connected with the application of TiO2 due to its band gap of 3.2 eV are limited. TiO2 is effective only in the UV-region (ca. 5%) of the solar spectrum with wavelengths λ

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p < 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

Abstract: Transcription factors are crucial pre-transcriptional regulatory mechanisms that can modulate the expression of downstream genes by binding to their promoter regions. DOF (DNA binding with One Finger) proteins are a unique class of transcription factors with extensive roles in plant growth and development. Our previous research indicated a decrease in iron content in chlorotic bamboo leaves. However, to our knowledge, genes related to iron metabolism pathways in bamboo species have not yet been studied. Therefore, in the current study, we identified iron metabolism-related (IMR) genes in bamboo and determined the transcription factors that significantly influence them. Among these, DOFs were found to have widespread effects and potentially significant impacts on their expression. We identified specific DOF members in Dendrocalamus latiflorus with binding abilities through homology with Arabidopsis DOF proteins, and established connections between some of these members and IMR genes using RNA-seq data. Additionally, molecular docking confirmed the binding interactions between these DlDOFs and the DOF binding sites in the promoter regions of IMR genes. The co-expression relationship between the two gene sets was further validated using q-PCR experiments. This study paves the way for research into iron metabolism pathways in bamboo and lays the foundation for understanding the role of DOF transcription factors in D. latiflorus.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

Severe acute respiratory syndrome coronavirus type 2 (SARS-CoV-2) continues to be a global threat due to its ability to evolve and generate new subvariants, leading to new waves of infection. Additionally, other coronaviruses like Middle East respiratory syndrome coronavirus (MERS-CoV, formerly known as hCoV-EMC) which first emerged in 2012, persists and continues to present a threat of severe illness to humans. The continued identification of novel coronaviruses, coupled with the potential for genetic recombination between different strains, raises the possibility of new coronavirus clades of global concern emerging. As a result, there is a pressing need for pan-CoV therapeutic drugs and vaccines. After extensive optimization of an HCV protease inhibitor screening hit, a novel 3CLPro inhibitor (MK-7845) was discovered and subsequently profiled. MK-7845 exhibited nanomolar in vitro potency with broad spectrum activity against a panel of clinical SARS-CoV-2 subvariants and MERS-CoV. Furthermore, when administered orally, MK-7845 demonstrated a notable reduction of viral burdens by >6 log orders in the lungs of transgenic mice infected with SARS-CoV-2 (K18-hACE2 mice) and MERS-CoV (K18-hDDP4 mice).

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

This article presents an innovative approach to the design of a safe adaptive backstepping control system. Tailored specifically for underactuated marine robots, the system utilizes simple sensors for enhanced practicality and efficiency. Given their operation in diverse oceanic environments fraught with various sources of uncertainties, ensuring the system's safe and robust behavior holds paramount importance in the control literature. To address this concern, this paper introduces a control strategy designed to ensure robustness at both the kinematic and dynamic levels. By emphasizing the compensation for the system uncertainties, the design integrates a straightforward fuzzy system structure. To further ensure the system's safety, a funnel surface is defined, followed by the design of a suitable nonlinear sliding surface as a function of the funnel and tracking error. Specifically leveraging the Lyapunov function, the study formally establishes the Semi-globally Practically Finite-time Stability of the closed-loop system, validated through simulations conducted on underactuated marine robots.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

Cocoa (Theobroma Cacao, L.) represents an important market that gained relevance and became an esteemed commodity thanks to cocoa powder, chocolate, and other related products. This work has analyzed 59 cocoa powder samples from the European market. Three distinct subgroups were identified: organic or conventional, alkalized or not alkalized, and raw or roasted processing. The impact of the technological process was evaluated on the pH, color, and compositional traits, as content of biogenic amines and salsolinol. The phenolic fraction was also investigated trough both common and emerging methods. Results depict that the influence of the agronomical practices (organic/conventional) did not affect significatively (p<0.05) the composition of cocoa powders; similarly, the roasting process was not discriminative for the compounds traced. On the other hand, the alkalinization process greatly impacted on color, and pH, no matter of cocoa provenience, obtention, or other processes, also resulting reducing the phenolic fraction of treated samples. Principal components analysis confirmed that the alkali process acts on pH, color, and phenolic composition, but not on other bioactives molecules (BAs and salsolinol). All samples resulted safe while alkalized powders have a great reduction in beneficial biocompounds. A novel strategy could be to emphasize non-alkalized powders in the label, to meet the demand for more beneficial products.

Oral squamous cell carcinoma (OSCC) is a highly prevalent and aggressive malignancy, with mortality rates that reach 60%, mainly due to an excessive diagnostic delay. MiRNAs, a class of crucial epigenetic gene-expression regulators, have emerged as potential diagnostic biomarkers, with >200 molecules reported to be dysregulated in OSCC. We had previously established an in silico methodology for the identification of the most disease-specific molecules by bridging genetics and epigenetics. Here, we identified the stage-specific miRNAs that govern the asymptomatic early stages of oral tumorigenesis by exploiting the reverse interplay between miRNA-levels and their target-genes’ expression. Incorporating gene expression data from our group’s experimental hamster model of sequential oral oncogenesis, we bioinformatically detected the miRNAs that simultaneously target/regulate >75% of the genes that are characteristically upregulated or downregulated in the consecutive stages of hyperplasia, dysplasia and early-invasion OSCC, while exhibiting the opposite expressional dysregulation in OSCC-derived tissue and/or saliva specimens. We found that all stages share the downregulation of miR-34a-5p, miR124-3p, and miR-125b-5p, while miR-1-3p is underexpressed in dysplasia and early-invasion. Malignant early-invasion stage is distinguished by the downregulation of miR-147a and the overexpression of miR-155-5p, miR-423-3p and miR-34a-5p. The identification of stage-specific miRNA molecules may facilitate their utilization as biomarkers for presymptomatic OSCC diagnosis.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

In numerical simulations, achieving high accuracy without significantly increasing computational costs is often challenging. To address this, this paper presents an improved finite volume weighted essentially non-oscillatory (WENO) scheme tailored for applicability in computational fluid dynamics (CFD) and implemented in the flow solver NUAA-Turbo for simulating turbomachinery flows using both RANS and RANS/LES coupling. Firstly, the new WENO scheme is validated against classic numerical test cases to assess its stability and reliability in handling discontinuities, the Double problem, and Raleigh-Taylor (RT) instability issues. Compared to the original format, this enhanced finite volume WENO scheme demonstrates superior stability near discontinuities and resolves flow features with the same grid resolution more effectively. Next, for engineering applications related to turbomachinery, such as compressor and turbine characteristics, computations are performed using RANS, and the results obtained using WENO-ZQ3 and WENO-JS3 are compared. Finally, the new fifth-order WENO scheme is applied to RANS/LES coupled simulations of turbine wakes and film cooling. The results show that the enhanced finite volume WENO scheme offers improved stability and accuracy in engineering applications, allowing for high-precision calculations with fewer grid points to capture more detailed flow physics, thereby reducing computational costs in aerodynamic applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.