In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

Advancements in 3D printing technologies have led to new implementations in rapid prototyping, microfluidics, tooling, dentistry, biomedical devices, drug delivery, and tissue engineering. Stereolithography techniques, which are photopolymerization-based processes, contribute to the optical, chemical, and mechanical properties of 3D printed materials using versatile polymer chemistry. This study used potassium titanate powder (K2Ti8O17) as an additive to enhance the mechanical strength of photocurable resins. PEG was selected as the stabilizer to optimize the dispersion and precipitation of potassium titanate. The flexural strength, hardness, and tensile strength were compared to assess the mechanical strength of the 3D printing resin. The flexural strengths of the printed specimens were in the range of 15–39 N/mm2. The measured surface hardness and tensile strength were 41–80 HV and 2.3–15 N/mm2, respectively. The output resolution of the potassium titanate/acrylate resin was tested using a line-pattern structure. 3D printing resin without stabilizers produced lines with a thickness of 0.3 mm, whereas 3D printing resin containing a stabilizer produced lines with a thickness of 0.2 mm. The flexural strength and pattern thickness results suggest that the potassium titanate/acrylate resin can be utilized as a 3D printer resin, suggesting new possibilities for potassium titanate materials.

Hybrid materials are a recent addition in the field of Restorative Dentistry for computer-assisted design/ computer-assisted manufacturing (CAD/CAM) indirect restorations. The long–term clinical success of modern dental restorative materials follows a multifactorial pattern. Among the characteristics, affecting the longevity of a restoration, mechanical properties and physicο – chemical interactions are of utmost importance. While numerous researchers constantly evaluate the mechanical properties, the biological background of resin–based CAD/CAM biomaterials is scarcely investigated and, therefore, less described in the literature. This review aims to analyze the biofilm formation on the surfaces of novel hybrid, resin–based CAD/CAM materials and evaluate the methodological protocols followed to assess microbial growth. It is demonstrated that the surface structure, the composition and the finishing and polishing procedures on the surface of a dental restorative material influence the initial bacterial adhesion; however most studies focus on in vitro protocols, whereas in vivo and/or in situ research of microbiomics in CAD/CAM restorative materials is lacking, obstructing in that manner the accurate understanding of the bioadhesion phenomenon in the oral cavity.

The objective of this study was to detail the monomer composition of resin-based dental materials sold in the market in 2023 and to evaluate the proportion of BPA derivatives in relation with their applications. A search on manufacturers’ websites was performed to reference resin-based dental materials currently on the market. Their monomer composition was determined from material safety data sheets and completed with a search on PubMed database. Among the 543 material compositions exploitable, 382 (70.3%) contained BPA derivatives. Among them, 56.2% contained BisGMA, 28% BisEMA, the most frequently reported. A total of 59 monomers of which 6 BPA-derivatives were found. 309 materials (56.9%) contained UDMA and 292 (53.8%) TEGDMA. Less than one third of materials identified contained no BPA derivatives. These proportions vary a lot depending on their applications with materials dedicated to dental care of young populations containing the highest proportions of BPA-derivatives monomers. The long-term effects on human health of the different monomers identified including BPA-derivatives monomers is a source of concern. For children and pregnant or lactating women arises the question to take a precautionary principle and avoid the use of resin-based dental materials likely to release BPA by opting for alternative materials.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

The aim of this study was to investigate the effect of laser irradiation to computer-aided de-sign/computer-aided fabrication (CAD/CAM) resin blocks coated with a silane coupling agent on the bond strength between the resin blocks and composite resin. The CAD/CAM resin blocks used in this study were Cerasmart 300 (GC) and Vita Enamic (Vita); they were cut into plates and then subjected to a series of treatments. After processing with a silane coupling agent, treatment with a semiconductor laser was performed at 3.0, 5.0, and 7.0 W, followed by the bonding procedures. The control group included those exposed to silane and bonded without laser application. After bonding, a mold with a simulated cavity was formed on the specimen and filled with flowable composite resin, and they were stored for 24 h or stressed by thermal cycling for subsequent testing that assessed the shear bond strength (n = 10). The results revealed that the bond strength was significantly enhanced by laser irradiation after applying a silane coupling agent, whereas significant effect was not detected between the materials. Particularly, 7 W laser irradiation had a significant effect on the bond strength between the composite resin and Cerasmart block after thermal cycling.

Purpose: This study aimed to evaluate the nanomechanical properties and chemical composition of restorative materials and dental surfaces using different toothpastes. Methods: Enamel (n=60) and dentin (n=60) bovine blocks were obtained and restored using resin-modified glass ionomer cement (RMGIC, n=30) or composite resin (CR, n=30) to form the dentin adjacent to RMGIC (DRMGIC), enamel adjacent to RMGIC (ERMGIC), dentin adjacent to CR (DCR), and enamel adjacent to CR (ECR). After restoration, one hemiface of each specimen was coated with an acid-resistant varnish to create the control (C) and eroded (E) sides (erosion: 5 days, 4 × 2 min/day; 1% citric acid / abrasion: 2 × 15 s followed by immersion on slurries 2 min). Three toothpastes were used: without fluoride (WF; n=10), sodium fluoride (NaF; n=10), and stannous fluoride (SnF2; n=10). The specimens were analyzed for nanohardness (H), elastic modulus (Er), and chemical composition using energy-dispersive X-ray spectroscopy (EDS) and Raman microscopy. Data were analyzed using ANOVA two-way repeated measures and Tukey’s test (α = 0.05). Results: The NaF presented lower values of H for DRMGIC-C, with a statistical difference for WF (p < 0.05). SnF2 resulted in lower Er values for ERMGIC-E and RMGIC-E than WF and NaF (p < 0.05). WF showed lower calcium and phosphorus concentrations for DCR-E than other types of toothpastes (p < 0.05). Only stannous-based toothpaste damaged the elasticity of eroded glass ionomer restorations performed in enamel. Toothpastes with fluoride was capable for maintaining main chemical elements of dentin adjacent to restorative materials under challenge conditions.

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

Immobilization of enzymes is a good field of study to expand the life of enzyme in and lowering the cost of the chemical processes such as separation processes. Urease is an important enzyme with medical and industrial applications. The aim of the present study is to prepare an immobilized urease on a strong cation exchange resin (Amberlite IR120 -Na) and study of its activity and stability. We monitored the liberation of Na ions in the collected fractions and searching for protein in the fractions as an indicators of immobilization by ion exchange phenomenon. Sodium is measured using atomic absorption spectroscopy techniques, while protein tested by Bradford’s method. Immobilized urease activity was evaluated by salicylate-hypochlorite method. The results indicated a complete immobilization of urease enzyme on the resin surface with reserving 92% of the activity of free enzyme. The immobilized urease enzyme on resin showed good stability and it has a 62% of its activity after 154 days of storage at room temperature. It is concluded that a new immobilized urease enzyme system is prepared with good enzyme activity and stability.

The crosslinking behavior of polyethylene (PE) determines its exceptional performance and application. In this study, we investigated the crosslinking behaviors of different PE resins through model simulation and rheological methods. Specifically, the mathematical equation of "S" model was established for PE resin. According to this equation, the optimal maximum gel content for high-density polyethylene (HDPE) was found to be around 85%. Moreover, the maximum crosslinking degrees for different PE resins depended largely on their density and molecular weight. The melt viscosities before crosslinking in PE resins were highly influenced by their melt index. The higher melt indexes resulted in the lower storage moduli, improving melt processability during processing. In addition, the crosslinking rates of PE resins were strongly influenced by peroxide concentration, independent of PE resin structures. For high molecular weight and low-density PE resins, they exhibited decreased ti values, increased A0 values, and decreased k6 values. However, there were no noticeable variations in the values of k2 and phi among different PE resins. And all simulated modeling outcomes showed the remarkable consistency with the experimental rheological data. These findings are of utmost significance in the industrial manufacture of PE resin.

Nano-titanium has excellent corrosion resistance and can be widely used in the field of corrosion resistant coatings. This paper introduces nano-weight titanium modified phenolic resin coatings and their anti-corrosion properties to explore the principle of nano-titanium modification and the mechanism of anti-corrosion to further develop more advanced corrosion resistant coatings. The article uses scanning electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and UV-Vis spectrophotometer to characterise the morphology and structure of the nano-titanium modified phenolic resin coatings and to determine the corrosion resistance properties of the modified phenolic resin coatings. The results show that the 4% nano-titanium modified phenolic resin coating, nano-titanium powder and phenolic resin will maximize the dispersion and combination, and the structure is good; nano-titanium grafted on phenolic resin, the successful preparation of nano-titanium modified phenolic resin; modified nano-titanium added to improve the coating's ability of UV absorption. The corrosion resistance of the coating is much better than that of the unmodified phenolic resin coating.

Introduction: To indentify the most effective actors(authors, countries, and journals) about composite resin restorations in the period 2000-2020.Material and Methods: An electronis research was conducted in the Scopus database by selecting the words ‘composite resin’ and ‘restoration and English language, article and review types, dentistry field. Their bibliometric data including publication title, authorship, citation count, citation dentistry, year of publication, country and institution of origin, journal of publication, study design, and keywords were extracted and analyzed.Results and Discussion: To our knowledge, this is the first bibliometric article on composite resin restorations. This study provides information about authors, institutions and countries that contribute to significant improvements in composite resin restorations. From 2000 to 2020, there were 7118 articles published from 99 countries.Articles originate primarily from the USA and Brazil. Results indicate that the USA, Brazil, Germany, Turkey, the United Kingdom, Japan, Swtizerland, Italy, Netherlands and India are the leading countries in composite resin restoration research and account for 51.8% of the total number of publications. The total number of citations are 158.404, corresponding to 22 citations per paper publication. During the time period examined, 776 hot articles and 228 classic articles on composite resin restorations were found.The journal with the most publications is ‘Operative Dentistry’. The publishing houses of the top 10 journals are from 4 countries: USA(6),Netherlands(2),Germany(1),Japan(1). The most cited article within the boundaires of this study is Ferracane’s article titled ‘Resin composite-State of the art’, which was published in Dental Materials in 2011 and received 913 citations.

In Mexico there is a deficit in the production of pine resin, because it depends on natural forests. Therefore, it is necessary to select provenances and phenotypes of potential species such as P. oocarpa. The objective was to determine the difference between provenances and the variation of resin components and quality, as well as the effect of geographic and climatic factors. Resin from five provenances was collected from southern Mexico. The percentage of rosin, turpentine and water was obtained, as well as the acidity and saponification index. P. oocarpa resin had 80.94 % rosin, 7.7 % turpentine and 11.49 % water. The saponification and acidity index was 125.47 and 117.49 mg KOH.g_1, respectively. All variables showed differences (p≤ 0.0001) between provenances. The provenance contributed between 6.44 and 11.71 % to the total variance, the error contributed between 88.29 and 93.56 %. Geographic and climatic variables only had an effect on the percentage of turpentine; the correlation was negative with altitude and longitude, but positive with temperature and precipitation. The results allow defining seed collection sites for resin plantations and orienting the selection for a P. oocarpa improvement program.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

In this present study, 3-pentadecyl-phenol was selected as a modifier to prepare a foamable phenolic resin with excellent performance, which was successfully prepared by in-situ modification. Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance (¹H NMR, ¹³C-NMR) were used to test and characterize the molecular structure of the modified resin. The results showed that 3-pentadecyl-phenol successfully modified the molecular structure of phenolic resin with a reduction in resin gel time. The effect of changing the added amount of 3-pentadecyl-phenol on the mechanical properties, microstructure and flame retardancy of the modified foam was investigated. The results showed that when the amount of added 3-pentadecyl-phenol was 15% of the total amount of phenol, this resulted in the best toughness of the modified foam, which could be increased to 300% compared to the bending deflection of the unmodified phenolic foam. The cell structure showed that the modified phenolic foam formed a more regular and dense network structure and the closed cell ratio was high. Furthermore, the compressive strength, bending strength, and limited oxygen index were improved, while the water absorption rate was lowered. However, the foam density could be kept below 40 mg/cm³, which does not affect the load.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Palm fatty acid distillate (PFAD) is a by-product from the refining of crude palm oil. It comprises mainly of free fatty acids, having around 45% of palmitic and 33% oleic acids as the major components. Ultra-violet (UV) curable urethane acrylate (UA) oligomers could be synthesized from PFAD by the following procedure. A hydroxyl terminated macromer was first prepared by reacting PFAD with a mixture of isophthalic acid, phthalic anhydride, neopentagylcol (NPG) and pentaerythritol. The macromer is then reacted with 2-hydroxylethylacrylate (2HEA) and toluene diisocynate (TDI) to generate a resin containing acrylate side chains for UV curable application. A series of UA resins were prepared by using 15, 25, 45, 55 and 70% of PFAD respectively. The UA resin has Mw in the range of 3200 to 27,000. They could be cured by UV irradiation at intensity of 225mW/cm². Glass transition temperature (T_g) of the cured film was measured by differential scanning calorimeter (DSC), and hardness of the film was determined by pendulum hardness tester according to ASTM4366. The resins were used in wood coating application. All of the cured films showed good adhesion, hardness and chemical resistant for resins using up to 55% PFAD; however the resin at 70% did not cure properly.

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

Commiphora molmol myrrh resin extracts, which have different physical properties such as polarity and dielectric constant, were prepared by immersion in extraction solvents (hot water, DMSO, hexane, ethanol, and methanol). Methanolic myrrh resin extracts showed broad antibacterial activity against isolated airborne bacteria. Furanoeudesma-1,3-diene and curzerene, as the main terpenoids in the methanolic myrrh resin extract, were analyzed using GC-MS, and the methanolic myrrh resin extracts were found to have antiviral activity (81.2% viral RNA inhibition) against H1N1 influenza virus. Biochars (wood powder-and rice husk-derived) coated with myrrh resin extracts also showed antiviral activity (22.6% and 24.3% viral RNA inhibition), due to the adsorption of terpenoids onto biochar. Myrrh resin extract using methanol as the extraction solvent is a promising agent with antibacterial and antiviral efficacy, and it can be utilized as a novel material via adsorption onto biochar for air filtration processes, cosmetics, fertilizers, drug delivery, and corrosion inhibition.

To develop a lower-cost, excellent performance, and environmentally friendly phe-nol-formaldehyde (PF) resin, soybean meal was used to modify PF resin, and soybean meal-phenol-formaldehyde (SMPF) resins were prepared. Their physicochemical properties and curing performance were investigated, showing that SMPF resins have higher curing tempera-tures than PF resin. The Fourier transform infrared spectroscopy (FTIR) results indicated that the cross-linking reaction occurred between the amino groups of soybean protein and the hy-droxymethyl phenol. Moreover, with the addition of soybean meal, the viscosity of SMPF in-creased while the gel time decreased. It is worth mentioning that SMPF-2 resin has favorable viscosity, short gel time, low curing temperature (135.78 °C), and high water resistance and bonding strength (1.01 MPa). Finally, all the plywoods bonded with SMPF resins have good water resistance and bonding strength, which could meet the Standard (GB/T 17657-2013, type I) for plywood. The optimized SMPF resins showed the potential application to replace part of PF resin in the wood industry.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

Polyurethane (PU) foam adhesives were prepared from castor oil as a polyol with isocyanate poly (4,4′-methylene diphenyl isocyanate) (PMDI) using a solvent-free process. The NCO/OH molar ratio used for the preparation of PU foams was 1.5. Water, organosiloxane and dibutyltin dilaurate were blowing agent, surfactant and catalyst, respectively. Effects of the ratio of blowing agent and catalyst were adjusted to optimize the properties. The results show that 4 wt% of castor oil of catalyst and blowing agent minimizes water absorption and maximizes volume expansion in the PU foams. FT-IR analysis shows that urethane bond was formed by hydroxyl group of castor oil and –NCO group of isocyanate PMDI. More blowing agent and catalyst could improve the volume expansion ratio and reduce water retention of PU foams. It was found that Moso bamboo charcoal (Phyllostachys pubescens) or/and China fir wood particle (Cunninghamia lanceolate) composites with setting densities of 500 and 600 kg/m³ can be prepared from optimized castor oil-based PU foam adhesive at 100 °C for 5 min under a pressure of 1.5 MPa. Increasing the amount of bamboo charcoal decreases the equilibrium moisture content, water absorption and internal bonding strength of the composite. Notably, bamboo charcoal composite exhibits excellent dimensional stability. The optimized density and bamboo charcoal percentages of the composite were 500 kg/m³ and 50 to 100%. The castor oil-based PU composites containing bamboo charcoal fulfilled the CNS 2215 standards for particleboard. This dimensionally stable, low-density bamboo charcoal composite has high potential to replace current indoor building materials.

The aim of this study was to using a lignin based resin (LB) to improve the performance of the soy flour based adhesive. Soy flour (SF), polyamidoamine-epichlorohydrin (PAE), LB was used to develop a plywood adhesive. The solid content and viscosity of the adhesive, functional groups, thermo-stability, and crystallinity of the cured adhesive were characterized and the performance of the resultant adhesive was evaluated by fabricating three-ply plywood. Results showed using LB and PAE mixture to modify SF adhesive improves dry and wet bond strength by 66.3 and 184.2%. PAE contributed more for the wet bond strength improvement and the LB contributed more for the dry bond strength. The improvement was attributed to: 1) LB/PAE reacted with the functions of the soy protein and form a cross-linking network; 2) Polycondensation reaction between LB molecules further improved crosslinking density of the adhesive and formed a interpenetration structure with crosslinked protein; 3)The easy penetration of LB on wood surface and formed more interlock with wood. The denser structure created by LB and PAE mixture improved the thermal stability and decreased the crystallinity of cured adhesive. The usage of the LB and PAE mixture increased solid content by 35.5%, meanwhile, makes its viscosity acceptable for the industrial application.

Shell nacre from Pinctada species has been extensively researched for managing bone defects. However, there is a gap in the research on using shell nacre as cement with improved physico-chemical properties. To address this, the current study aimed to develop a chemical curable com-posite shell nacre cement (SNC) using shell nacre powder and an organically modified ceramic resin shell nacre containing ladder-structured siloxane methacrylate (SNLSM). Different amounts of shell nacre (24, 48, and 72 weight(wt)%) were added to the SNLSM resin matrix and the effect on the physicochemical properties of the cement was studied. The composite shell nacre cement SNC 72 containing 72 wt% shell nacre exhibited significantly higher mechanical properties (com-pressive strength >100 MPa, flexural strength > 35 MPa) and low linear polymerization shrinkage (0.4%) than other compositions. SNC 72 was radiopaque and the exotherm generated during the curing of the cement was minimal. Direct contact of cured SNC 72 with L929 cells revealed the non-cytotoxic nature of the cement. Overall, the results of the study proved that the composite SNC 72 would be a promising candidate for bone defect management.

Asphalt cement will not last for a long time as the world encounters a diminishment in the crude oil. For sustainable, flexible pavement development, new resources can provide a contribution to replace it partially or entirely. In this study, asphalt was partially and entirely replaced by guayule resin as a bioresource by-product, extracted during the guayule natural rubber production. Crumb rubber modifier (CRM) was used as an asphalt enhancer. The Superpave grading system was followed at high, intermediate, and low temperatures to evaluate such innovative binder for rutting, fatigue, and thermal cracking, respectively, in addition to viscosity. Therefore, the original, short-term aging and long-term aging were simulated using tank, rolling thin film oven, and pressure aging vessel materials. Additionally, component analysis using Fourier-transform infrared spectroscopy was provided to link the rheological properties with the chemical changes. Outcomes showed a relatively much lower viscosity of guayule in the same high-temperature asphalt grade indicating savings in plant energy consumption and reduced environmental emissions. CRM enhanced guayule, but not as much as asphalt, proven by polymeric component migration through liquid binder. This enhancement was reflected in the rheological performance besides other factors. As-received guayule seems to have high oxygen content proven by strong absorption peak intensities of oxidative bonds (e.g., Carbonyl and sulfoxide). Such pre-oxidation was negatively reflected in the intermediate- and low-temperature performance of guayule and guayule-based binders. However, the investigated guayule had potential to compensate for asphalt replacement in the presence of CRM by 23–42% by weight of blend.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

In order to improve the performance of soft plantation wood, an environmentally friendly inorganic-organic hybrid wood modifier was developed. First, using urea and melamine as crosslinking agents, the waterborne glucose silicone resin (MUG) was prepared with glucose under the catalysis of inorganic acid and metal ions. Then MUG resin was diluted to 10% and 20% mass fraction, and compounded with sodium silicate (S) of 20% and 10% mass fraction, so the inorganic-organic hybrid G10S20 and G20S10 wood modifier were obtained respectively. Then plantation poplar wood (Populus tomentosa) were impregnated and modified with them. Their physical and mechanical properties were tested and compared with those of the wood treated with S of 20% mass fraction (S20). Infrared analysis showed that amino resin characteristic structure (CO-NH-) existed in MUG resin. The resin has good permeability. Compared with S20 modified wood, the degree of shrinkage of G10S20 or G20S10 modified wood is reduced, their moisture absorption is reduced, and their dimensional stability is improved. Waterborne glucose silicone modifier can effectively improve the wood density, modulus of elasticity, modulus of rapture and compression strength. SEM analysis showed that the cell wall of G20S10 modified wood was significantly thicker than the untreated wood, and there were columnar and granular solid substances attached in some cell cavities, ducts and corners, etc. EDX showed that the number of Si elements on the cell wall was significantly increased compared with the control, indicating that the modifier effectively entered the wood cell wall. The waterborne glucose silicone resin can greatly improve the physical and mechanical properties of wood through organic-inorganic hybridization. It is a green, non-formaldehyde, eco-friendly, low cost, compound wood modifier with broad application prospects.

In these last years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product's lifespan. The main purpose of this study is to investigate the nano-indentation response in terms of hardness, reduced modulus, contact depth and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating a good agreement. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

In this study, the effect of ZnO nanoparticles (Zn NPs) on the performance of epoxy resin composites was investigated. The new ZnO/epoxy resin composites were synthesized using halloysite nanotubes (HNT) and different types of ZnO nanoparticles (commercial ZnO and ZnO-ODTES). These ZnO nanoparticles were utilized for intending to enhance the interfacial bonding between the epoxy resin and the reinforcement. Various methods such as FTIR, TGA, DSC, TEM-EDX, and Nanoindentation analyses were used to prove that the ZnO nanoparticles can improve the properties of epoxy resin composites. The thermal properties of the epoxy resin composites were enhanced to a greater extent by the addition of ZnO NPS. DSC testing proved that the epoxy resin composites modified with ZnO NPS are more flexible and elastic than unmodified epoxy resin. It was seen that the epoxy resin modified with ZnO-ODTES shows a much improved hardness and penetration depth compared to the other samples. These findings can pave the way for the developing of ZnO-based marine coatings with improved properties.

In this study, cotton fabric reinforced phenolic resin (CPF) composites were modified by adding four two-dimensional fillers: graphitic carbon nitride (g-C3N4), graphite (Gr), molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN). The tribological properties of these modified materials were investigated under dry friction and water lubrication conditions. CPF/ Gr composite exhibits significantly better tribological performance than the other three fillers modified CPF composites under dry friction, with a 24% reduction in friction coefficient and a 78% reduction in wear rate compared to unmodified CPF composite. Under water lubrication conditions, all four fillers did not significantly alter the friction coefficient of the CPF composite. However, except for an excessive amount of Gr, the other three fillers can reduce the wear rate. Particularly, in the case of 10% MoS2 content, the wear rate decreased by 56%. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were employed for the analysis of the morphology and composition of the transfer films. Additionally, molecular dynamics (MD) simulations were conducted to investigate the adsorption effects of Gr, MoS2, and PF on the counterpart surface under both dry friction and water lubrication conditions. The difference in the adsorption capacity of Gr and MoS2 on the counterpart, as well as the resulting formation of transfer films, accounts for the variation in tribological behavior between CPF/Gr and CPF/MoS2 composites. By combining the lubrication properties of MoS2 and Gr under dry friction and water lubrication conditions, using them as co-fillers can achieve a synergistic lubrication effect.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

Literature revealed the potential of using guayule resin for asphalt cement replacement from the binder’s perspective. However, monitoring guayule resin through binder-aggregate mixture could disclose its performance through field. In this study, designated binders were employed to investigate the applicability of such an innovative replacer through mixture, which were neat asphalt and guayule-based binders (neat guayule, asphalt-rubber-guayule, guayule-rubber binders). Consecutively, field-simulated lab mixtures were prepared to investigate the major distresses. Moisture damage, rutting, fatigue cracking, and thermal cracking resistances were investigated using the modified Lottman (TSR) test, rut test by asphalt pavement analyzer (APA), semi-circular bending (SCB) test, and disk-shaped compact tension (DCT) test, respectively. Additionally, the Hamburg wheel-tracking (HWT) test was employed to evaluate moisture susceptibility and rutting resistance. Outcomes revealed that the neat guayule was susceptible to moisture damage at a 7% air content (V_a) when the TSR test was employed. In contrast, all investigated mixtures yielded perfect performances against moisture susceptibility under the HWT test. Guayule-based mixtures perfectly resisted rutting, as analyzed by the rut test and HWT test. Generally, changing parameters (e.g., V_a, rubber addition, and partial asphalt replacement by guayule and rubber) enhanced the guayule-based mixture resistance to rutting and moisture damage resulting in acceptable performances. Guayule-based mixture had a high fracture toughness at low temperatures, hence fatigue fracture resistance at intermediate temperatures. Neat guayule mixture with or without rubber addition did not entirely resist thermal fracture. However, partial asphalt replacement by guayule and rubber resisted the thermal fracture to a great extent.

The nanocomposites with reversible cross-linking covalent bonds were prepared by reacting furfurylamine (FA)-modified diglycidyl ether of bisphenol A (DGEBA) and furfuryl-functionalized aniline trimer-modified graphene (TFAT-G) with bismaleimide (BMI) via Diels-Alder (DA) reaction. The successful synthesis of the TFAT modifier is confirmed by NMR hydrogen spectroscopy and IR spectroscopy tests. The structure and properties of TFAT-G epoxy nanocomposites are characterized by SEM, DSC, tensile and resistivity CES. The results show that TFAT-G was uniformly dispersed in the resin, and 1wt% TFAT-G composites increase to 233% for tensile strength, 63% for elongation at break, 66.1% for modulus and 7.8℃ for Tg. Overall, the graphene/self-healing resin nanocomposites have both good self-healing function and electrical conductivity by adding 1% modified graphene and still maintain the original 83% strength and 89% electrical conductivity after one cycle of heating repair.

Repairing of small and isolated delamination area in carbon fiber reinforced polymer (CFRP) without significantly altering the composite structure is studied in this research. A small drilled hole was introduced at the center of the delamination section of CFRP, providing the channel for epoxy infill of sharp delamination cracks. The pressureless infill repair was achieved through the capillary action of an acetone-diluted resin solution (without hardener) with CNT reinforcement, e.g., 89 m/m% of acetone, 10 m/m% of resin and 1m/m% of CNT. Such an acetone-rich resin pre-coating (RPC) solution is easy to prepare and apply to the drilled hole area. Curing of CNT-toughened resin infill was induced by filling the small-drilled hole with a resin-hardener mixture toughened by CNT/Aramid pulp. The effectiveness of delamination repair with curing periods of two weeks and three months were compared. Flexural strength measurements indicated that 77% (potentially 100%) of the restoration was achievable.

This research seeks to interpret the component analysis of an innovative bio-asphalt binder using guayule resin in addition to crumb rubber modifier (CRM) at high concentrations. Such asphalt modification aims to minimize the dependency on virgin asphalt binder and provide new solutions concerning sustainable, flexible pavement industry. Guayule resin is a promising bioresource for asphalt binder replacement. By now, it could be considered a no value byproduct extracted during the guayule natural rubber production. CRM is a recycled material derived from scrap tires. The provided interpretation could help in understanding the asphalt-rubber-guayule interaction mechanism. Fourier transform infrared spectroscopy (FTIR), supported by thermo-gravimetric analysis (TGA), was used to investigate the component analyses of guayule resin composition, asphalt guayule interaction, and asphalt rubber guayule interaction, compared to corresponding asphalt rubber interaction. Additionally, the rheological properties at elevated temperatures were provided to link the microscale properties with the final product performance. The study clarified the distinct carbon and hydrogen compositional elements of guayule resin. Asphalt and guayule resin have similarities in chemical composition and rheological behavior with temperature susceptibility. The asphalt guayule binder had physical interaction. However, when both interacted with rubber, a chemical interaction was attributed, with no difference in rubber dissolution tendency, in asphalt rubber guayule, compared to asphalt rubber. A bio-binder composed of 62.5% asphalt, 25% guayule and 12.5% CRM had the potential to provide rheological properties better than base asphalt. Such behavior was interpreted by a high release of rubber components.

Objectives: The current study aimed to compare the adaptation of the restored class-I cavities with two self-etch adhesives bonded to two resin composite using cross-polarization optical coherence tomography (CP-OCT). Materials and Methods: Cylindrical class-I cavities were prepared on twenty, extracted human premolars. Two self-etch adhesives; Clearfil SE bond 2 (SE; Kuraray Noritake Dental, Japan) and Bond Force (Palfique Bond) adhesive (PL; Tokuyama Dental, Japan) were used in this study that were bonded to either resin composites materials; Herculite XRV microhybrid dental composite (HRV; Kerr, Italy) or Estelite Alpha composite (ESA; Tokuyama Dental, Japan). The specimens were divided into four groups (n=5); SE-HRV, SE-ESA, PL-HRV and PL-ESA. All specimens were varnished and stored in distilled water for 24h. Then, they were submerged in a contrasting medium. After that, all groups were optically imaged under CP-OCT at every 250 µm interval distance. Later, image binarization and gap quantification were carried out using Image analysis software. Result: There was a significant difference between all the groups except between SE-ESA and PL-ESA (p = 0.51). The highest median gap % was seen in PL-HRV group followed by SE-ESA, PL-ESA and SE-HRV. Conclusion: Other than composite filler loading and adhesive formula, the interactions of the adhesive and composite copolymers have great influence on composite adaptation.

Mechanical properties of three-dimensional (3D) printed resin can be improved by decreasing oxygen concentrations during post-curing, and nitrogen saturated post-curing has been applied for the purpose. This study aimed to evaluate and compare the color stability of 3D printed resin crowns post-cured in normal air and nitrogen saturated conditions. Crowns were fabricated with 3D printer and post-cured in normal air (control group; air) or nitrogen saturated condition (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed through repeated measures ANOVA. Fourier Transform Infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Comparing the effects of post-curing conditions, significant difference was found between control and experimental groups over immersion time in wine and curry subgroups. In FT-IR analysis, there was significant difference in degree of conversion between the air and nitrogen groups from 10 to 300 seconds. The findings suggest that nitrogen saturated post-curing can potentially enhances the conversion rate of 3D printed resin crowns, thereby improving their color stability.

The article describes the use of microwave irradiation in the synthesis of bis(cyclo carbonate) compounds (BCC) in bulk (without solvent) from carbon dioxide capture using an epoxidized compound - a commercial epoxy resin, and compares this process to the conventional method. CO2 cycloaddition to epoxides is an ecological and efficient method for the formation of bis(cyclic carbonates). Moreover, the introduction of gas into the reaction mixture was carried out at atmospheric pressure with a controlled flow rate, which is advantageous from an economic point of view. Progressive structural changes and the presence of characteristic chemical groups were monitored using attenuated total reflectance infrared spectroscopy with Fourier transform. The obtained crude products were purified to obtain three fractions, which were subjected to detailed structural analysis using FT-IR and 13CNMR. The formation of the main product with two cyclic carbonates was confirmed. The presence of monomers, dimers and trimers in individual fractions as well as their thermal stability were determined, and the molecular masses in individual fractions were determined using gel permeation chromatography (GPC).

Tree resin, which in addition to its widespread use in industry is also a macroergic component which has not yet been used for energy purposes. The main goal of this work is to determine the energy content of the resin of spruce, pine and larch and wood components – pulp and turpentine. The combustion heats of resin (MJ/kg) from each timber was determined calorimetrically. The energy values of tree resin (&gt;38.0 MJ.kg-1) were 2.2 and 2.4 times higher than that of bleached and unbleached cellulose, the highest value was recorded for the turpentine (&gt;39.0 MJ.kg-1). The best way of resin tapping is the America method, providing 5 kg resin ha-1 yr-1. The resin quantity tapped was raised at least 3 times applying stimulant, its production cost compared to other feedstocks was the cheapest. The tree resin can be applied as a good means to mitigate global warming and consequently dampen climate change. One tonne of tree resin burned instead of coal spares the atmosphere by 5.0 Mt CO2 since it is environmentally neutral. As resin heating values approach to the lower end of ones of liquid hydrocarbon fuels, greater efforts are needed to examine the most efficient energy use of resin.

Nymphaea lotus L. is the medicinal plant that has long been used as food, cosmetic and traditional medicines in Africa and Asia since the ancient time. Its flavonoids and other interesting phytochemical compounds from rhizome, leaf, and the whole flowers have been reported in the previous published researches. However, stamens, which are essential for reproductive functions, may also represent new alternative sources of potential antioxidant flavonoids as investigated in this study. The innovative green chemistry method i.e. ultrasound-assisted extraction (USAE) as well as macroporous resin (MPR) purification procedure were employed in this current research. The optimal ultrasound-assisted extraction condition is 90 % (v/v) aqEtOH with 34.65 khz ultrasonic frequency and 46 minutes of extraction time. Comparing with heat reflux extraction (HRE) conventional method, the significant gain of 1.35 total flavonoids content was obtained using optimized USAE conditions, jumping to 2.80 when this USAE associated with MPR purification. Not only in vitro cell free antioxidant activity of N. lotus stamen extracts, but also in cellulo antioxidant investigation using yeast model showed the same trend to indicate that the best antioxidant flavonoid can be found in USAE coupled with MPR purification. Moreover, the key antioxidant genes expression in yeast model such as SIR2 and SOD2 were also expressed at the highest level in yeast cell treated with the extract from USAE together with MPR purification. Consequently, it can be seen that the USAE combined with MPR purification can help to enhance the flavonoids antioxidant potential of the stamens extract from this medicinal species.

The objective was to compare the color match and color stability behavior of single and multishade resin-based composites (RBCs) used for direct restorations. This review was conducted according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines. Randomized clinical trials evaluating the shade performance of single-shade RBCs in direct restorations were included. A search of the scientific literature was performed in 5 databases (April 2024). The meta-analysis was performed using RevMan 5.4, calculating the risk difference (RD) and 95% confidence interval (CI) of the dichotomous outcome using a random effects model. Bias was assessed using the RoB 2.0 tool, and certainty of evidence was assessed using the GRADE tool. Four studies with 263 restorations analyzed were selected. The results showed comparable performance between single-shade RBCs and multishade RBCs in terms of color match and color stability over 12 months. Three studies had a low risk of bias with all expected results, and one study had some concerns. The certainty of evidence for color stability was considered low for all follow-up periods due to the small number of events and sample size. According to the United States Public Health Service Evaluation (USPHS) and the World Dental Federation (FDI), there is comparable clinical color performance between single-shade and multishade RBCs over 12 months.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

Nanocomposites of cyanate ester resin (CER) filled with three different reactive amino-functionalized polyhedral oligomeric silsesquioxane (POSS) were synthesized and characterized. The addition of a small quantity (0.1 wt.%) of amino-POSS chemically grafted to the CER network led to increasing thermal stability of CER matrix. A significant increase of the glass transition temperature, Tg (DSC data), and the temperature of α relaxation, Tα (DMTA data), by 45-55 оС of CER matrix with loading of nanofillers was evidenced. CER/POSS films exhibited a higher storage modulus than that of neat CER in the temperature range investigated. It was evidenced that CER/aminopropylisobutyl (APIB)-POSS, CER/N-phenylaminopropyl (NPAP)-POSS, and CER/aminoethyl aminopropylisobutyl (AEAPIB)-POSS nanocomposites induced a more homogenous α relaxation phenomenon with higher Tα values and an enhanced nanocomposite elastic behavior. Furthermore, CER/amino-POSS nanocomposites possessed higher specific surface area, gas permeability (CO2, He), and diffusion coefficients (CO2) values than those for neat CER, due to increasing free volume of the nanocomposites studied that is very important for their gas transport properties. Permeability grew respectively by about 2 (He) and 3.5-4 times (СО2), and diffusion coefficient of CO2 increased approximately twice for CER/amino-POSS nanocomposites in comparison with the neat CER network. The efficiency of amino-functionalized POSS in improving the thermal and transport properties of the CER/amino-POSS nanocomposites increased in a raw of reactive POSS containing one primary (APIB-POSS) &lt; eight secondary (NPAP-POSS) &lt; one secondary and one primary (AEAPIB-POSS) amino groups. APIB-POSS had the least strongly pronounced effect, since it could form covalent bonds with the CER network only by reaction of one –NH2 group, while AEAPIB-POSS displayed the most highly marked effect, since it could easily be incorporated into the CER network via reaction of –NH2 and –NH– groups with –O–C≡N groups from CER.

Copper ferrite attracts a lot of interest from researchers as a material with unique magnetic, optical, catalytic and structural properties. In particular, the magnetic properties of this material are structurally sensitive and can be tuned by changing the distribution of Cu and Fe cations in octahedral and tetrahedral positions by controlling synthesis parameters. In this study, we propose a new simple and convenient method for the synthesis of copper ferrite nanoparticles using a strongly basic anion exchange resin in OH form. The effect and possible mechanism of polysaccharides addition on the elemental composition, yield and particle size of CuFe2O4 is investigated and discussed. It is shown that anion exchange resin precipitation leads to a mixture of unstable at standard temperature cubic (c-CuFe2O4) and stable tetragonal (t-CuFe2O4) phases. The effect of the reaction conditions on the c-CuFe2O4 stability is studied by temperature-dependent XRD measurements and discussed in terms of the cations distribution, Jahn−Teller distortion and Cu2+ and oxygen vacancies in the copper ferrite lattice. The obtained differences in the values of saturation magnetization and the coercive force of prepared samples are explained with a reference to variations in the particle sizes and the structural characteristics of copper ferrite.

This study evaluated the efficacy of experimental TEGDMA-functionalized dicalcium phosphate dihydrate (T-DCPD) filler-based resin-based composites (RBC) in preventing caries lesions around the restoration margins (secondary caries”, SC). Standardized Class-II cavities were made in sound molars having the cervical margin in dentin. Cavities were filled with a commercial resin-modified glass-ionomer cement (RMGIC) or experimental RBCs containing a BisGMA-TEGDMA resin blend and one of the following inorganic fractions: 60 wt.% Ba glass (RBC-0); 40 wt.% Ba glass, 20 wt.% T-DCPD (RBC-20); 20 wt.% Ba glass, 40 wt.% T-DCPD (RBC-40). An open-system bioreactor produced S. mutans biofilm-driven SC. Specimens were scanned using micro-CT to evaluate demineralization depths. Scanning Electron Microscopy and Energy-dispersive X-ray Spectroscopy characterized the specimens’ surfaces, while antimicrobial activity, buffering effect, and ion uptake by the biofilms were also evaluated. ANOVA and Tukey’s test were applied at p<0.05. RBC-0 and RBC-20 showed SC development in dentin, while RBC-40 and RMGIC significantly reduced the lesion depth at the restoration margin (p<0.0001). Initial enamel demineralization could be observed only around RBC-0 and RBC-20 restorations. A direct antibiofilm activity could explain SC reduction by RMGIC, while a buffering effect on biofilm’s acidogenicity explained the behavior of RBC-40. Experimental RBC with CaP-releasing functionalized T-DCPD filler could prevent SC with the same efficacy as F-releasing materials.

Tooth decay, also known as caries, is a significant medical problem that harms teeth. Treatment is based on the removal of the carious material and then filling the cavity left in the tooth, most commonly with amalgam or composite resin. The consequences of filling failure include repeating the filling, or performing another treatment, such as a root canal, or extraction. Dental amalgam contains mercury, and there is a global effort to reduce its use. However, no consensus has been reached using randomized clinical trials, regarding whether amalgam or composite resin materials are more durable, and which is the best restorative material. To determine which material is superior, we performed a retrospective cohort study using a large database where members of the 58 dental clinics with 440 dental units were treated. The number of failures of the amalgam compared to composite resin restorations between 2014 and 2021 were compared. Our data included information from over 650,000 patients. Between 2014 - 2021, 260,905 patients were treated. 19,692 out of 113,281 first amalgam restorations failed (17.49%), whereas significantly fewer composite restorations failed (11.98%) 65,943 out of 555,671. This study indicates that composite is superior to amalgam and therefore it is reasonable to cease using mercury containing amalgam.

The pressing process and density profile of particleboards produced with addition of waste wood containing phenol-formaldehyde (PF) resin was presented. The particles were melamine-urea-phenol-formaldehyde (MUPF) resinated. Recovered particles were obtained from post-industrial waste plywood. The press closing time recorded during the pressing of mats containing only recovered particles in the core layer (100%), at a unit pressure of 3 MPa, in which the face layer rate was 50%, resin load for face and core layer was 12% and 10% was shorter by 29% than for the industrial particle mats. Regardless of the level of variability of independent factors the overheating time of mats to a temperature of 100 °C, containing recovered particles was 10% - 20% shorter than the time of overheating mats with industrial particles. The greatest impact (52%) on maximum density of the face layer of particleboards was demonstrated by the content of the recovered particles and the resin load (32%). The maximum density area of the face layer was located closer to the surface in particleboards produced with a higher (80%, 100%) content of the recovered particles, a higher (i.e. 12% and 10%, respectively, for face and core layer) resin load, a lower (35%) face layer rate and a higher (3 MPa ) unit pressure.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

The reinforcing effect of boehmite nanoparticles (BNP) in epoxy resins for fiber composite lightweight construction is related to the formation of a soft but bound interphase between filler and polymer. The interphase is able to dissipate crack propagation energy and consequently increases the fracture toughness of the epoxy resin. Usually, the nanoparticles are dispersed in the resin and then mixed with the hardener to form an applicable mixture to impregnate the fibers. If one wishes to locally increase the fracture toughness at particularly stressed positions of the fiber-reinforced polymer composites (FRPC), this could be done by spraying nanoparticles from a suspension. However, this would entail high costs for removing the nanoparticles from the ambient air. We propose that a fiber fleece containing bound nanoparticles be inserted at exposed locations. For the present proof-of-concept study, an electrospun polycarbonate nonwoven and taurine modified BNP are proposed. After fabrication of suitable PC/EP/BNP composites, the thermomechanical properties were tested by dynamic mechanical analysis (DMTA). Comparatively, the local nano-mechanical properties such as stiffness and elastic modulus were determined by atomic force microscopy (AFM). An additional investigation of the distribution of the nanoparticles in the epoxy matrix, which is a prerequisite for an effective nanocomposite, is carried out by scanning electron microscopy in transmission mode (TSEM). From the results it can be concluded that the concept of carrier fibers for nanoparticles is viable.

Antimicrobial edible coatings could eliminate pathogen contamination risk on the surface of meat and poultry products during storage. In this study, the edible coating (EC) based on wheat gluten, Pistacia vera L. tree resin (PVR), and essential oil (EO) of PVR were applied on chicken breast fillets (CBF) by dipping method to prevent the growth of Salmonella Typhimurium and Listeria monocytogenes. The samples were packed in foam trays wrapped with low-density polyethylene stretch film and stored at 8°C for 12 days to observe antimicrobial effects and sensory properties. The total bacteria count (TBC), L. monocytogenes, and S. Typhimurium were reported during the storage. All samples coated with EC containing 0.5, 1, 1.5, and 2% v/v EO (ECEO) decreased microbial growth significantly compared to control samples. The growth of TBC, L. monocytogenes, and S. Typhimurium was suppressed by 4.6, 3.2, and 1.6 logs, respectively, at the end of 12 days on the samples coated by ECEO (2%) compared to uncoated controls (p&lt;0.05). Coating with ECEO (2%) also preserved appearance, smell, and general acceptance parameters better than uncoated raw chicken (p&lt;0.05) on the 5th day of storage. In grilled chicken samples, ECEO (2%) did not significantly change the sensory properties of appearance, smell, and texture but had increased taste and general acceptance scores (p&gt;0.05). So, ECEO (2%) can be a feasible and reliable alternative to preserve chicken breast fillets without affecting their sensory properties adversely during the shelf life.

Novolac phenol-formaldehyde resins have gained extensive commercial utilization across diverse applications due to their exceptional mechanical, thermal, and chemical resistance properties. In this investigation, we successfully synthesized a traditional novolac, and a biobased novolac phenol-formaldehyde resin by partially substituting phenol with a bio-oil obtained from the organic phase resulting from the fast pyrolysis of pinewood biomass. Despite extensive investigations into the curing behavior of novolac resins crosslinked with hexamethylenetetramine (HMTA) through numerous model-fitting cure kinetic studies, a comprehensive model for predicting the crosslinking of bio-based phenol-formaldehyde resins in the presence of HMTA has not yet been studied. The primary objective of this research was to compare and apply several commonly used kinetic models to predict the degree of curing and cure rate of the synthesized resins, using DSC dynamic measurements. Our results demonstrated that the autocatalytic model exhibited excellent fitting for the traditional novolac resin and HMTA mixture, while the Kamal model showed better fitting with the experimental data obtained for the bio-based phenol-formaldehyde resin and HMTA system. In addition, the results evidenced a significant drop in the curing temperature by partially replacing phenol with bio-oil. Additionally, the results revealed a notable reduction in curing temperature when phenol was partially substituted with bio-oil. This substitution not only offers environmental benefits but also promotes energy efficiency and enhances production safety. The data collected in this study is pivotal for our subsequent research endeavors, which aim to develop environmentally sustainable materials optimized for use in 3D printing manufacturing processes.

The purpose of the study was to investigate the bacterial viability of the initial biofilm on the surface of experimental modified dental resin composites. Twenty-five healthy individuals with good oral hygiene were included in this study. In a split-mouth design, they received acrylic splints with five experimental composite resin specimens. Four of them were modified with either a novel polymeric hollow beads delivery system or methacrylated polymerizable Irgasan (Antibacterial B), while one specimen served as unmodified control (ST). The delivery system based on Poly-Pore® was loaded with one of the active agents Tego® Protect 5000 (Antiadhesive A), Dimethicone (Antiadhesive B) or Irgasan (Antibacterial A). All study subjects refrained from toothbrushing during the study period. Specimens were detached from the splints after 8h and given a live/dead staining before fluorescence microscopy. Friedman test and post-hoc Nemenyi test were applied with significance level at p &lt; 0.05. In summary all materials but Antibacterial B showed a significant antibacterial effect compared to ST. In conclusion dental resin composites with Poly-Pore loaded active agents show antibacterial effectiveness in situ.

A The aim of this study is to analyze the effect of different endodontic irrigants and adhesive systems on resin bond strength of fiber post cementation. 144 single-rooted, unrestored human teeth were endodontically treated and randomly divided into 12 groups according to 4 endodontic irrigants (distilled water as control; EDTA 17%; NaOCl 5%; clorhexidine 2%) and 3 different adhesive/resin cement systems (etch-and-rinse: ortofosforic acid, Parabond® A+B/Paracore®; self-etch: ParaBond® Non-Rinse Conditioner, Parabond® A+B /Paracore®; Universal: ClearfilTM Universal Bond/ ClearfilTM DC Core Plus). 48 h after post cementation ten teeth from each group were cross sectioned into 3 discs (cervical, middle and apical regions). 30 specimens of each group (n=30) were submitted to push-out test at a crosshead speed of 1 mm/min. The remaining 2 teeth of each group were sectioned in the same manner and the resin-dentin interface was evaluated using scanning electron microscopy (SEM). The results were statistically analyzed with the ANOVA and Tukey’s test (< 0,01). The adhesive protocols and post space region showed no significant effect on bond strength (> 0.01). The combination of NaOCl 5% and ClearfilTM Universal Bond reduced the adhesive strength (< 0.01). The NaOCl 5%, in relation with other irrigants, significantly decreased the push-out bond strength.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

Climate change is challenging the agricultural sector worldwide. The pressure exerted by the altered thermal conditions drives the zonal shift for various cultivations. This study presents the multiyear analysis of the Growing Degree Days (GDD) index over the Northern Mediterranean Basin (NMB), focused on the high-value vine cultivation derived from the E-OBS dataset. To handle this extensive environmental dataset, R-language scripts and packages were applied, along with the capabilities of the GIS software. The investigated time period spans from 1969 to 2018, and the performed analysis indicates a broad shift/expansion in areas of GDD exceeding 2000 heat units. The extracted results specify the viticultural areas where the GDD index surpasses the suitable values for vine cultivation, owing to the increase of the thermal stress risk. In addition to mapping areas with GDD ≥ 2000, spatial calculations of the surface of areas meeting this criterion per country in the study area were made. In the northern parts of the NMB, the rise of the GDD index values indicates the establishment of vine plantations in the future.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x104 – 2x107 CFU per ml and has a sensitivity of S = 1.655x105 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10-9 grams (g) which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Regeneration of lost tail is of great importance to lizards. Anolis carolinensis, a green lizard, is capable of regenerating its tail efficiently after autotomy. Hence, it is considered as a model organism in regeneration study. A. carolinensis shed its tail in order to distract the predator’s attention and thus makes a way to escape. Restoring of the amputated tail takes several days and the mechanism is currently clearly understood. Although save its life, tail regeneration is associated with the impairment of several vital functions in Anoles. In addition, various differences have been observed between original and regenerated tail in terms of mechanism and structure. To date, very little work has been conducted on tail autotomy and regeneration at molecular and genetic level. The genes responsible for regeneration in anoles are identified recently. These genes are evolutionarily conserved through all tetrapod vertebrates. They are, however, in a state of ‘switched-off’ in other vertebrates including humans. Consequently, a throughout study of these so called ‘switched-off’ genes may provide a way of restoring lost organs in human, and thus could revolutionize the modern medical science.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water