The aim of this retrospective study was to compare the clinical outcomes of treating isolated surgical neck fractures of the humerus using either the intramedullary nail or the MIROS (Minimally Invasive Reduction and Osteosynthesis System®) system. The study included 42 patients who underwent surgical treatment at the Polyclinic from January 2014 to June 2020. The results indicated that both treatments were effective; however, the MIROS system exhibited a higher complication rate. Intramedullary nailing was more reliable, thus recommended as the primary treatment method. This study underscores the importance of selecting the appropriate fixation technique to minimize complications and enhance patient outcomes.

In order to achieve the dual carbon goal and simplify the decarbonization process, a CO2 recovery process of the fire-flooding exhaust was designed. The process adopted the two-stage membrane separation method to recover CO2 and obtain high purity CO2 rich flow, and then through the mixed refrigerant liquefaction and rectification column, food grade liquid CO2 was obtained. HYSYS process simulation shows that for the fire-flooding exhaust with a flow rate of 1000 kg/h and a given composition, the process can achieve a CO2 recovery of 69.02%, total product sales S=2086.8 yuan/h, and specific power consumption of 2.818 kW∙h/kg. On this basis, a hybrid simulation platform of HYSYS & Matlab was established. Taking the specific power consumption of the product as the objective function, sequential quadratic programming (SQP) algorithm was adopted to optimize the process, and the optimized specific power consumption was reduced by 18.8%. Finally, by adjusting N2/CO2 components, the adaptability of the optimization condition was analyzed.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.

With the advent of microservice-based software architectures, an increasing number of modern cloud environments and enterprises use operating system level virtualization, often referred to as containers. Docker Swarm is one of the most popular container orchestration infrastructures, providing high availability and fault tolerance. Occasionally discovered container escape vulnerabilities allow adversaries to execute code on the host operating system and operate within the cloud infrastructure. We show that docker swarm is currently not secured against misbehaving manager nodes and allows a high impact, high probability privilege escalation attack that we refer to as leadership hijacking. Cloud lateral movement and defense evasion payloads allow an adversary to leverage the docker swarm functionality to control each and every host in the underlying cluster. We demonstrate an end-to-end attack, in which an adversary with access to an application running on the cluster achieves full control of the cluster. To reduce the probability of a successful high impact attack, container orchestration infrastructures must reduce the trust level of participating nodes and in particular, incorporate adversary immune leader election algorithms.

In the last decades, we have witnessed a spectacular information explosion over the Internet. Millions of users are consuming the Internet through various services, such as mobile applications, and online games. The service providers, at the back-end side, are supported by state-of-art infrastructures. Targeting on providing the services at scale, virtualization is one of the emerging technologies used in data centers and cloud environments to improve the quality of services. In this project, we aim to develop a dynamic resource management scheme based on virtual containers. It collects the runtime job progress from the running tasks and allocates the resources dynamically to improve the overall system performance.

All types of sports are potential application scenarios for automatic and real-time visual object and event detection. In rink hockey, the popular roller quad skate variant of hockey team sports, it is of great interest to automatically track player’s movements and positions, player’s sticks and, also, making other judgments, such as being able to locate the ball. In this work, we introduce a real-time pipeline composed by an object detection model, created specifically for rink hockey games, followed by a knowledge-based event detection module. Even in the presence of occlusions and quick motions, our deep learning object detection model effectively identifies and tracks, in real-time, important visual elements such as: ball; players; sticks; referees; crowd; goalkeeper; and goal. Using a curated dataset composed by a collection of videos of rink hockey, comprising 2525 annotated frames, we trained and evaluated the algorithm performance and compare it to state of the art object detection techniques. Our object detection model, based on YOLOv7, presents a global accuracy of 80%, and presents a good performance in terms of accuracy and speed, according to our results, making it a good choice for rink hockey applications. In our initial tests, the event detection module successfully detected one important event type in rink hockey games, the occurrence of penalties.

Summary Genome assembly projects have grown exponentially due to breakthroughs in sequencing technologies and assembly algorithms. Evaluating the quality of genome assemblies is critical to ensure the reliability of downstream analysis and interpretation. To fulfil this task, we have developed the AssemblyQC pipeline that performs file-format validation, contaminant checking, contiguity measurement, gene- and repeat-space completeness quantification, telomere inspection, taxonomic assignment, synteny alignment, scaffold examination through Hi-C contact-map visualisation, and assessments of completeness, consensus quality and phasing through K-mer analysis. It produces a comprehensive HTML report with method descriptions, tables, and visualisations. Availability and Implementation The pipeline uses NextFlow for workflow orchestration and adheres to the best-practice established by the nf-core community. This pipeline offers a reproducible, scalable, and portable method to assess the quality of genome assemblies – the code is available online.GitHub: https://github.com/Plant-Food-Research-Open/assemblyqc Supplementary information Pipeline usage documentation, parameter descriptions and example outputs are available on GitHub: https://github.com/Plant-Food-Research-Open/assemblyqc/tree/main/docs. A preview report is also hosted online: https://plant-food-research-open.github.io/assemblyqc

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

This paper thoroughly assesses the ARM and RISC-V architectures in the context of High-Performance Computing (HPC). It includes an analysis of Docker, Kubernetes, and KVM virtualization integration. Our study aims to evaluate and compare these systems' performance, scalability, and practicality in a general context and then assess the impact that might have on special use cases, like HPC. ARM-based systems exhibited better performance and seamless integration with Docker and Kubernetes, underscoring their advanced development and effectiveness in managing high-performance computing workloads. On the other hand, despite their open-source architecture, RISC-V platforms presented considerable intricacy and difficulties in coordinating with Kubernetes, which hurt their overall effectiveness and ease of management. The results of our study offer valuable insights into the practical consequences of implementing these architectures for HPC, highlighting ARM's preparedness and the potential of RISC-V while acknowledging the increased complexity involved and significant trade-offs at this point.

RNA sequencing techniques, like bulk RNA-seq and Single Cell (sc) RNA-seq, are critical tools for the biologist looking to analyze the genetic activity/transcriptome of a tissue or cell during an experimental procedure. Platforms like Illumina's next-generation sequencing (NGS) are used to produce the raw data for this experimental procedure. This raw FASTQ data must then be prepared via a complex series of data manipulations by bioinformaticians. This process currently takes place on an unwieldy textual user interface like a terminal/command line that requires the user to install and import multiple program packages, preventing the untrained biologist from initiating data analysis. Open-source platforms like Galaxy have produced a more user-friendly pipeline, yet the visual interface remains cluttered and highly technical, remaining uninviting for the natural scientist. To address this, SeqMate is a user-friendly tool that allows for one-click analytics by utilizing the power of a large language model (LLM) to automate both data preparation and analysis (differential expression, trajectory analysis, etc). Furthermore, by utilizing the power of generative AI, SeqMate is also capable of analyzing such findings and producing written reports of upregulated/downregulated/user-prompted genes with sources cited from known repositories like PubMed, PDB, and Uniprot.

The rapid and accurate detection of viruses and the discovery of single nucleotide polymorphisms (SNPs) are crucial for disease management and understanding viral evolution. In this study, a pipeline for virus detection, validation, and SNP discovery from next-generation sequencing (NGS) data is presented. By integrating state-of-the-art bioinformatics tools with artificial intelligence, the pipeline processes raw sequencing data to identify viral sequences with high accuracy and sensitivity. Before aligning the reads to the reference genomes, quality control measures and adapter trimming are performed to ensure the integrity of the data. Unmapped reads are subjected to de novo assembly to reveal novel viral sequences and genetic elements. The effectiveness of the pipeline is demonstrated by the identification of virus sequences, illustrating its potential for the detection of known and emerging pathogens. SNP discovery is performed using a custom Python script that compares the entire population of sequenced viral reads to a reference genome. This approach provides a comprehensive overview of viral genetic diversity and identifies dominant variants and a spectrum of genetic variations. The robustness of the pipeline is confirmed by the recovery of complete viral sequences, which improves our understanding of viral genomics. This study highlights the synergy between traditional bioinformatics techniques and modern approaches, providing a robust tool for analyzing viral genomes and contributing to the broader field of viral genomics.

This study presents the design and implementation of a piezoelectric power harvesting device to capture vibrational strength from pipelines to autonomous strength IoT devices. The gadget utilizes key components along with the PPA-1001 piezoelectric sensor, STM32F103C8T6 microcontroller, and LTC-3588 energy harvesting strength delivery. Experimental results verified the gadget's performance in harvesting strength within a specific frequency variety of 10 Hz to 50 Hz, with the foremost overall performance at 30 Hz. The device generated the highest voltage of 3.3V, delivering a strength output of 2.18 mW, which is sufficient to power low-strength electronic gadgets. The device maintained solid performance across a temperature range of 20°C to 35°C, underscoring its robustness in various environmental situations. The findings highlight the capacity of this generation to offer a sustainable power source for far-off pipeline tracking, contributing to stronger protection and operational efficiency.

Developing a dependable gas and condensate value chain is vital for the ongoing prosperity of the oil and gas industries. To achieve this, NNPC is enhancing its production facilities by employing process modeling and simulation with the assistance of Symmetry iCON®. As a part of this initiative, a simulation model was created using the Symmetry iCON® pipe plexus solver to simulate the dynamic environment of the gas and condensate pipeline network in the Nigerian Southern region. To validate the model, data from a single month, specifically December 2022, was utilized. Furthermore, the algorithm was utilized to generate projections for the month of January 2023, providing valuable insights into its effectiveness. The study also highlighted the significance of accurately estimating the characteristics and properties of a pseudo component of C6+ in relation to thermodynamics and material properties, which was a particularly insightful finding. he assessment of this property has transitioned from being relatively unimportant to becoming critically important, primarily due to the lack of condensate data monitoring at specific terminals. However, it's worth noting that the model currently has an error margin of 4-6% when predicting the data. As more information becomes available in the future, the model can be easily fine-tuned to better align with the actual conditions, allowing for more accurate predictions.

This research delves into the water hammer occurrences, in the transmission pipeline of the SMD (Manda Daba) Multi Village Water Supply Schemes in Afar, Ethiopia. It utilizes simulation software, Bentley HAMMER version 8i to assess transient flow issues and the effectiveness of protective measures. The study pinpoints high risk areas in Scenario 1 marked by pressure spikes, negative pressures and frequent cavitation highlighting the importance of efforts. Prior to safeguards significant pressures reaching 288.27 m H₂O and minimum pressures dropping as low as 9.98 m H₂O are observed. In Scenario 2 where protective measures are implemented notable enhancements are seen with pressures ranging from 121.38 m H₂O to 150.49 m H₂O improved safety levels and substantial reductions in minimum pressures at pump stations. Moreover the study delves into Scenario 3 which explores pipe materials and diameters to provide insights, for pipeline design standards. It emphasizes how protective measures effectively mitigate water hammer effects while also highlighting cost saving potential by incorporating 2000 liter hydro tanks at pump stations. This integration leads to decreased pipeline collapses and maintenance expenses underscoring the significance of addressing challenges pinpointing failure causes and offering solutions to enhance system performance and strengthen reliability within the SMD water supply system

Pipelines extend thousands of kilometers to transport and distribute oil and gas. Given the challenges often faced with corrosion, fatigue, and other issues on steel pipes, the demand for glass fiber reinforced plastics (GFRP) pipes is increasing in the oil and gas gathering and transmission systems. However, the medium transported through these pipelines contains multiple acid gases such as CO2 and H2S, as well as ions including Cl-、Ca2+、Mg2+、SO42-、CO32- and HCO3-. These substances can cause a series of problems, such as aging, debonding, delamination, and fracture. In this study, a series of aging damage experiments were conducted on V-shaped GFRP pipes with depths of 2mm and 5mm. The aging and failure of GFRP were studied under the combined effects of external force and acidic solution using acoustic emission (AE) techniques. It was found that the acidic aging solution promoted matrix damage, fiber/matrix desorption, and delamination damage in GFRP pipes over a short period. However, the overall aging effect was relatively weak. Based on the experimental data, the SSA-LSSVM algorithm was proposed and applied to the damage pattern recognition of GFRP. An average recognition rate of up to 90% was achieved, indicating that this method is highly suitable for analyzing AE signals related to GFRP damage.

There is need to accurately design pipelines to transport the expected increase of CO₂ captured from industrial processes after the signing of the Paris Climate Agreement in 2016. This paper reviews several aspects of CO₂ pipeline design with emphasis on pressure drop and models for the calculation of pipeline diameter. Two categories of pipeline equations were identified. The first category is independent of pipeline length and has two different equations. This category is used to specify adequate pipeline diameter for the volume of fluid transported. The optimum economic pipe diameter equation (Eq. 17) with nearly uniform resultant velocity values at different flow rates performed better than the standard velocity flow equation (Eq. 20). The second category has four different equations and is used to calculate pipeline pressure drop or pipeline distance for the installation of booster stations after specifying minimum and maximum pipeline pressures. The hydraulic equation is preferred because it gave better resultant velocity values and the closest diameter value obtained using Aspen HYSYS (V.10) simulation. The effect of impurities on the pressure behaviour and optimal pipeline diameter and pressure loss due to acceleration were ignored in the development of the models. Further work is ongoing to incorporate these effects into the models.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

During our digital transition, Docker containers have become essential for adaptable application deployment, although posing inherent security threats. This study utilizes Trivy for static analysis and Falco for dynamic analysis to identify and address vulnerabilities in Docker environments before deployment and in real-time. The IoT sector is now dealing with security issues that are made more severe by extensive connectivity and the prevalence of WiFi. This research promotes the use of AWS cloud security technologies such as IoT Core, CloudWatch, and GuardDuty to protect IoT devices from threats, with the goal of maintaining user privacy and ensuring safety in our interconnected digital world. This comprehensive strategy aims to enhance security measures in both Docker and IoT sectors, strengthening the security framework in our interconnected world.

Cloud-induced atmospheric extinction and occlusion have a major effect on the effectiveness and quality of telescope observations. Real-time cloud cover distribution and long-term statistical data are essential for astronomical siting and telescope operations. At ground-based astronomical telescope sites, cloud cover distribution is currently analyzed using manual observation methods. However, the main disadvantages of manual observation methods are human subjective, heavy workloads and poor real-time performance. Therefore, a real-time automatic cloud images classification method is desperately needed. This paper presents a new cloud identification method, which is named PSO+XGBoost model by combining eXtreme Gradient Boosting (XGBoost) and Particle Swarm Optimization (PSO). The entire cloud image is divided into 37 sub-regions in order to more precisely identify the distribution of the clouds. 19 features are then extracted, including the sky background, star density, lighting conditions, and subregion grayscale values. The experimental results have shown that the overall classification accuracy of 96.91% and our model is able to outperform several state-of-the-art baseline methods. Our approach achieves high accuracy in comparison with the manual observation methods. Moreover, this method meets telescope real-time scheduling requirements.

This paper employs the Finite Element Method (FEM) to simulate and analyze the effects of corrosion defect parameters on the stress and failure pressure of pipelines. It investigates how the boundary conditions of the pipeline model influence stress and examines the sensitivity of failure pressure to corrosion defect parameters. A nonlinear regression equation has been developed from a dataset obtained through simulation experiments to predict the failure pressure of corroded pipelines. To validate the effects of corrosion defect parameters on failure pressure, a hydrostatic test platform for an API 5L X65 pipeline with corrosion defects was established to measure stress levels and failure pressures across varying corrosion defects. The study reveals that failure pressure is negatively correlated with corrosion length and depth, while positively correlated with corrosion width. Among these parameters, corrosion depth exerts a more significant influence on the pipeline's failure pressure than corrosion length and width. Within the range of corrosion defect parameters examined, the maximum deviation of the prediction equation's results from the simulation results is 8.71%, with an average deviation of 5.81%. The standard deviation of the fitted residuals is 0.01837. Additionally, the maximum deviation between the predicted results and experimental measurements is 8.39%, with an average deviation of 7.77%. The strong agreement between the predicted results from the equation and the actual measured data underscores the effectiveness of the nonlinear regression equation.

ABSTRACT Purpose: Tongue image analysis for disease diagnosis is an ancient traditional non-invasive diagnosis technique widely used by traditional medicine practitioners. Deep Learning based multi-label disease detection models offer tremendous potential to clinical decision support systems, by facilitating preliminary diagnosis. Methods: In this work, we propose a multi-label disease detection pipeline, where in observation and analysis of tongue images captured and received via smartphones assist in predicting the health status of an individual. All images are voluntarily given by subjects consulting collaborating physicians. Images thus acquired are first and foremost classified either into a diseased or a normal category by a 5-fold cross-validation algorithm using a convolution neural network (MobileNetV2) model for binary classification. Once the diseased label is predicted, the image is used to diagnose multiple diseases using the prediction algorithm based on DenseNet121. Results: Average accuracy of 93 % was achieved in classifying diseased from normal healthy tongue by detection model with MobileNetV2 architecture. Multilabel disease classification produced more than 90% accurate results for the seven class labels considered. Conclusion: AI based image analysis shows promising results and an extensive dataset could provide further improvements to this approach. Rather than employing high-cost sophisticated image capturing setup, experimenting with smartphone images opens opportunity to provide preliminary health status to individuals on smartphone prior to further line of treatment and diagnosis.

YOLOv8, as an efficient object detection method, can swiftly and precisely identify objects within images. However, traditional algorithms encounter difficulties when detecting small targets in remote sensing images, such as missing information, background noise, and interactions among multiple objects in complex scenes, which may affect performance. To tackle these challenges, we propose an enhanced algorithm optimized for detecting small objects in remote sensing images, named HP-YOLOv8. Firstly, we design the C2f-D-Mixer (C2f-DM) module as a replacement for the original C2f module. This module integrates both local and global information, significantly improving the ability to detect features of small objects. Secondly, we introduce a feature fusion technique based on attention mechanisms, named Bi-Level Routing Attention in Gated Feature Pyramid Network (BGFPN). This technique utilizes an efficient feature aggregation network and reparameterization technology to optimize information interaction between different scale feature maps, and through the Bi-level Routing Attention (BRA) mechanism, it effectively captures critical feature information of small target objects. Finally, we propose the Smooth Mean Perpendicular Distance Intersection over Union (SMPDIoU) loss function. The method comprehensively considers the shape and size of detection boxes, enhances the model's focus on the attributes of detection boxes and provides a more accurate bounding box regression loss calculation method. To demonstrate our approach's efficacy, we conduct comprehensive experiments across the RSOD, NWPU VHR-10, and VisDrone2019 datasets. The experimental results show that the HP-YOLOv8 achieves 95.11%, 93.05%, and 53.49% in the [email protected] metric, and 72.03%, 65.37%, and 38.91% in the more stringent [email protected]:0.95 metric, respectively.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

Transcatheter Aortic Valve Implantation (TAVI) now represents the mainstay in the treatment of severe aortic stenosis. Owing to its exceptional procedural efficacy and safety, TAVI has been extended to include patients at lower surgical risk, thus now encompassing a diverse patient population receiving this treatment. Yet, long-term outcomes also depend on optimal medical therapy for secondary vascular prevention, with antithrombotic therapy serving as a cornerstone. Leveraging data from multiple randomized controlled trials, current guidelines generally recommend single antithrombotic therapy, with either single antiplatelet therapy (SAPT) or oral anticoagulation (OAC) alone in those patients without, or with atrial fibrillation respectively. Yet, individualization of this pattern, as well as specific case uses, may be needed based on individual-patient characteristics and concurrent procedures. This review aims to discuss the evidence supporting antithrombotic treatments in patients treated with TAVI, indications for a standardized treatment, as well as specific considerations for an individualized approach to treatment.

Pavement crack detection is one of the key links in highway pavement maintenance management. In the current road crack detection, the network model easily ignores the shallow geometric features of cracks and cannot extract the key feature information of cracks. Aiming at the above problems, an EC-YOLOX network model is proposed. The CFPN is constructed to cross-fuse different scale features to solve the feature scale invariance. In the strengthen feature extraction layer, ECANet is fused to enhance the ability to pay attention to key information. The WEIoU loss function is proposed, which assigns different penalty terms to the target box in the vertical and horizontal directions. In terms of data, geometric distortion constraint correction is performed on the single-point perspective pavement image. The experimental data show that the accuracy of EC-YOLOX on the self-built data set reaches 76.34% [email protected], which is 4.45% higher than that of YOLOX. The loss curve of EC-YOLOX is smoother than that of YOLOX, and the minimum training loss value is 2.136, which is 0.648 lower than the minimum loss value 2.784 of YOLOX. Many experiments have verified the effectiveness of EC-YOLOX in improving the detection effect in pavement crack detection.

Many have speculated that events of personal and financial loss in Rembrandt’s life caused depression and that this is revealed by examination of his self-portraits particularly those painted in old age. Some report detecting various physiological diseases associated with aging, including vision impairment, which may have affected his mood and work. Aging and neurodegenerative disease which often accompanies it, are both associated with depression. Recent advances in imaging and computer technology make it possible to empirically examine changes in artistic style which can contribute to understanding artists’ physical and mental health. In the current study changes in contrast, colour and fractal dimension were measured in the entire corpus of Rembrandt’s painted self-portraits and portraits to determine whether changes in style indicate depression or disease. Productivity was also examined as an indirect indicator. Given the high salience attributed to self-images, it also examined whether differences in style could be detected between self-portraits and portraits of related and unrelated others. The results indicate that it is unlikely that Rembrandt suffered from unipolar or bipolar depression, age-related cognitive decline, or neurodegenerative disease. The data are consistent with someone experiencing episodes of low mood consistent with normal grieving and adversity followed by resilient recovery. There is evidence of a gradient in saliency and complexity between self-portraits and related and unrelated portraits, of a less formal style in portraits of related others and of a ‘late’ style identified by leading art historians consistent with macular degeneration. The results are also consistent with an association of aesthetic preference with mid-level fractal values tending towards the Golden Mean long associated with beauty in nature and in art.

Within the research of pressure pipeline inspection methods there is an industry that is constantly growing and becoming more efficient. The purpose of inspection methods on pressure pipelines comes back to the issue of resolving leaks, corrosion, and inability of a pipeline to function (eventually). Evidently, these issues can hurt the environment, the public using the material being carried out by these pressure pipelines such as natural gas or petroleum and can hurt the pockets of pipeline companies that did not react quick enough to their pipeline solely for the reason that they may have not noticed there was an issue with their pressure pipeline. In-line inspection methods are continuously growing and have already made an impact to prevent the catastrophes that occur when a pipeline is not maintained. Technology such as smart pigs, MFLs, and ultrasounds are the future of pressure pipeline inspection. This research paper explains their pros and cons and how they’re overall more efficient and preferred as the primary inspection method for a pipeline. Older, more traditional methods such as aerial inspection, by-foot inspection, hydrostatic pressure testing, and Direct Assessment does not cover every base of inspection like in-line inspection technology does and this research explains why that is and the areas of where in-line inspection technology can be improved and deemed not as useful. This is where trenchless renewal and replacement methods come into play with inspection methods and determining the characteristics of a pipeline that matches with which inspection method and which trenchless method to use. The future of inspection methods for pressure pipelines is attainable and is somewhat already here, this research discusses the new emerging technologies and how designing in-line inspection technology to be cheaper and more versatile with pipeline characteristics can make everyone a winner in the future. A winner as far the environment being safe, neighborhoods near pressure pipelines being safe, companies being able to install in-line inspection technology at a fraction of the cost of today and the efficiency of pipelines by monitoring the characteristics with this new technology.

Over the last decade, the prevalence of health issues has increased by approximately 29.1%, putting a substantial strain on healthcare services. This has accelerated the integration of machine learning in healthcare, particularly following the COVID-19 pandemic. The utilization of machine learning in healthcare has grown significantly, however many present approaches are unsuitable for real-world implementation due to high memory footprints and lack of interpretability. We introduce DeClEx, a pipeline designed to address these issues. DeClEx ensures that data mirrors real-world settings by incorporating gaussian noise and blur and employing autoencoders to learn intermediate feature representations. Subsequently, our convolutional neural network, paired with spatial attention, provides comparable accuracy to state of the art pre-trained models while achieving threefold improvement in training speed. Furthermore, we provide interpretable results using explainable AI techniques. We integrate denoising and deblurring, classification and explainability in a single pipeline called DeClEx.

Personalized medicine is an aspect of the P4 medicine (predictive, preventive, personalized and participatory) based precisely on the customization of all medical characters of each subject. In personalized medicine, the development of medical treatments and drugs is tailored to the individual characteristics and needs of each subject, according to the study of diseases at different scales from genotype to phenotype scale. To make concrete the goal of personalized medicine, it is necessary to employ high-throughput methodologies such as Next Generation Sequencing (NGS), Genome-Wide Association Studies (GWAS), Mass Spectrometry or Microarrays, that are able to investigate a single disease from a broader perspective. For example, by using genotyping microarrays (e.g. collections of Single Nucleotide Polymorphism - SNP) it is possible to uncover the reasons (i.e. mutation in genes) because a treatment works properly in some patients (for example absence of mutated genes), but it does not work (presence of mutated genes) in others. A side effect of high-throughput methodologies is the massive amount of data produced for each single experiment, that poses several challenges (e.g. high execution time and required memory) to bioinformatic software. Thus a main requirement of modern bioinformatic software is the use of good software engineering methods and efficient programming techniques, able to face those challenges, that include the use of parallel programming and efficient and compact data structures. Thus, to exploit all the potential of this massive amount of data in the short possible time (before that data becomes obsolete), the necessity to develop parallel software tools for efficient data collection and analysis arise. Moreover, due to the heterogeneity of the data produced by the different kinds of experimental platforms, it is necessary to automatize in a comprehensive software pipeline, the various steps that compose a bioinformatic analysis, such as: the preprocessing of raw data to remove noise or corrupted data; the annotation of data with external knowledge (e.g. Gene Ontology), and the integration of molecular data with clinical data. It should be noted that such steps are necessary to make statistical or data mining analysis more effective. This paper presents the design and the experimentation of a comprehensive software pipeline, named microPipe, for the preprocessing, annotation and analysis of microarray-based SNP genotyping data. A case study in pharmacogenomics is presented. The main advantages of using microPipe are: the reduction of errors that may happen when trying to make data compatible among different tools; the possibility to analyze in parallel huge datasets; the easy annotation and integration of data.

Ocean exploration is crucial for utilizing its extensive resources. Images captured by underwater robots suffer from issues such as color distortion and reduced contrast. To address the issue, we propose an innovative enhancement algorithm that integrates Transformer and Convolutional Neural Network (CNN) in a parallel fusion manner. Firstly, a novel transformer model is intro-duced to capture local features, employing peak-signal-to-noise ratio (PSNR) attention and linear operations. Subsequently, to extract global features, both temporal and frequency domain features are incorporated to construct convolutional neural network. Finally, the Fourier’s high and low-frequency information of the original image are utilized to fuse different features. To demon-strate the algorithm's effectiveness, underwater images with various levels of color distortion are selected for both qualitative and quantitative analyses. The experimental results demonstrate that our approach surpasses other mainstream methods, achieving superior PSNR and structural sim-ilarity index measure (SSIM) metrics and leading to a detection performance improvement of over ten percent.

Governments worldwide are actively committed to achieving their carbon emission reduction targets, and one avenue under exploration is harnessing the potential of hydrogen. Blending hydrogen with natural gas is emerging as a promising strategy to reduce carbon emissions, as it burns cleanly without emitting carbon dioxide. This blending could significantly contribute to emissions reduction in both residential and commercial settings. However, a critical challenge associated with this approach is the potential for Hydrogen Embrittlement (HE), a phenomenon wherein the mechanical properties of pipe steels degrade due to the infiltration of hydrogen atoms into the metal lattice structure. This can result in sudden and sever failures when the steel is subjected to mechanical stress. To effectively implement hydrogen-natural gas blending, it is imperative to gain a comprehensive understanding of how hydrogen affects the integrity of pipe steel. This necessitates the development of robust experimental methodologies capable of monitoring the presence and impact of hydrogen within the microstructures of steel. Key techniques employed for this assessment include microscopic observation, hydrogen permeation tests, and tensile and fatigue testing. In this study, samples from two distinct types of pipeline steels used in the natural gas distribution network underwent rigorous examination. To induce hydrogen absorption, an electrochemical charging process is employed in a solution rich in H+ ions. This charging process, accomplished by a potentiostat applying a constant current, prompts the hydrogen evolution reaction at the steel specimen, acting as the cathode of the charging cell. Immediate tensile and fatigue testing following the charging process enables the evaluation of mechanical properties in comparison to non-charged samples. Different charging current densities are employed to simulate various hydrogen blend scenarios. The findings from this research indicate that charged samples exhibit a discernible decline in fatigue and tensile properties. This deterioration is attributed to embrittlement and reduced ductility stemming from the infiltration of hydrogen into the steel matrix. The extent of degradation in fatigue properties is correlated not only to the hydrogen content but also to the hydrogen permeability and diffusion rate influenced by steel’s microstructural features, with higher charging current densities indicating a more significant presence of hydrogen in the natural gas pipeline blend.

Pipes have been utilized since ancient times and have seen significant renewal, modification, and replacement to improve their effectiveness and efficiency in the modern era. As early as 4000 BC, Egyptians used clay pipes for drainage systems. The U.S. has the largest network of energy pipelines in the world. The ASCE 2017 Infrastructure Report Card assigned grades of D and D+ to water and wastewater pipelines, highlighting a substantial need for improvement. The paper investigates the infrastructure required for the sustainability of pipeline systems, as well as the construction of underground systems using both open-trench and trenchless technologies, along with the associated risks in the US. It concludes that trenchless methods are increasingly preferred for pipeline construction due to technological advancements, reduced surface disruptions, shorter construction times, and lower social costs. Tackling this challenge will necessitate strategic investment, decisive leadership, thorough planning, and meticulous preparation for future demands. Enhancing pipeline infrastructure can stimulate the U.S. economy, whereas postponing action will lead to higher costs.

Accent is on determination of appropriate friction factor of the pipes and on selection of the representative equation for water or natural gas flow which is valuable for existing conditions in the looped network of pipelines. Note that in a municipal gas pipeline, natural gas can be treated as incompressible fluid (liquid) i.e. as water or oil. Even under this circumstance, calculation of water pipelines cannot be literary copied and applied for calculation of gas pipelines. Inappropriate friction factor, equally as e.g. inappropriate usage of water flow equations for calculation of gas networks can lead to inaccurate final results. Few iterative methods for determining the optimal hydraulic solution of water- and gas- looped pipeline networks, such as, Hardy Cross, modified Hardy Cross, node-loop method, node and M.M. Andrijashev method, will be shown. Speed of convergence will be compared and discussed using a simple network with three loops.

Due to poor ventilation conditions in the tunnel, if gas pipeline leaks, the consequence of the accident will be more serious. Therefore, before the emergency repair, gas in the tunnel needs to be excharged so as not to explode during the repair process. Therefore, it is necessary to study the ventilation of gas in the tunnel. Based on the computational fluid dynamics (CFD) theory and taking the Yanyingshan tunnel section of China-Myanmar pipeline as an example, this paper uses Fluent software to establish the leakage model of the gas pipeline and fan model in the tunnel and analyzes the influence of different fan locations and number of fans on gas concentration. It can be concluded that: (1) the use of press-in method makes it more efficient to discharge gas out of the tunnel. (2) In order to make ventilation efficient, the fan should be arranged in a higher position and needs to be at a distance from the top of the tunnel. (3) Parallel use of two fans has better ventilation effect than single fan.

Train fault detection primarily relies on the comparative analysis of collected images with standard reference images, making the accurate identification of the collected image types crucial for effective fault detection. Most current systems achieve indirect classification of carriage images by using Automatic Equipment Identification (AEI) devices to recognize carriage identification number information while capturing the carriage images. However, damaged RF tags or blurred characters can hinder these devices, obstructing further train fault analyses. The unique features of carriage linear array images, such as high resolution, extreme aspect ratios, and local non-linear distortions, pose significant challenges to recognition algorithms. This paper proposes a method specifically designed to recognize these types of images. First, we implement an object detection algorithm to locate the positions of key components in carriage linear array images. By leveraging the spatial layout mapping between these key components and the carriage type classification, we simplify the complex image recognition problem into a sparse point set alignment task. To ensure effective registration despite local distortions in the linear array images, we propose a weighted radial basis function. To address the issues of unknown matching relationships and quantity mismatches during point set alignment, the proposed objective function is designed to maximize the similarity between Gaussian mixtures of point sets, thereby determining the RBF weights. Extensive experiments have demonstrated that our algorithm achieves 100% recognition accuracy under local nonlinear scale distortions of less than 15%. The algorithm remains effective even in the presence of some false positives or missed detections in key component object detection results. It can accurately identify the target category from 79 image categories within 24 milliseconds on an i7 CPU without GPU support. It is of great significance to reduce system cost and promote automatic exterior fault detection for train rolling stock.

With the rapid developments that have been made in computer vision and computer technology, semantic segmentation of high-resolution images has emerged as a mainstream and challenging task. The, segmentation of water areas remains a complex task due to the similar features between water areas or between water areas and other land objects. Meanwhile, since coastlines and riverbanks are typically presented in irregular shapes, it is difficult to obtain the categories of pixels at boundaries. This paper proposed the use of a Water-Land Boundary Attention Network (WLBANet) to improve the accuracy of pixels at boundaries between water and land. This network also reinforced the performance of contextual information extraction into distinguishing between water areas and other land objects. To prove the validity of this proposed network, WLBANet was performed on the Water Land Dataset (WLD), which is also by this paper, and which contains water areas and other land objects categories. The results demonstrates that the proposed method has significant effectiveness.

This study proposes and validates a novel combustion control system for Oil-Fired Boilers aimed at reducing air pollutant emissions through flame image prediction. The proposed system is easily applicable to existing ships. Traditional proportional combustion control systems supply fuel and air at fixed ratios according to the set steam load, without considering the emission of air pollutants. To address this, a stable and immediate control system is proposed, which adjusts the air supply to modify the combustion state. The combustion control system utilizes oxygen concentration predictions from flame images via SEF+SVM as control inputs, and applies Internal Model Control (IMC)-based Proportional-Integral (PI) control for real-time combustion control. Due to the complexity of modeling the image-based system, IMC parameter tuning through experimentation is essential for achieving effective control performance. Experiments conducted on a 3000 kg/h marine oil-fired boiler in actual operation optimized the controller parameters for stability and responsiveness, and validated their effectiveness. The results demonstrate the potential of the proposed system to improve combustion efficiency and reduce emissions of air pollutants. This study provides a feasible and effective solution for enhancing the environmental performance of marine oil-fired boilers. Given its ease of application to existing ships, it is expected to contribute to sustainable air pollution reduction across the maritime environment.

Fluorescence microscopic images of cells contain a large number of morphological features that are used as an unbiased source of quantitative information about cell status, through which researchers can extract quantitative information about cells and study the biological phenomena of cells through statistical and analytical analysis. As an important research object of phenotypic analysis, images have a great influence on the research results. Saturation artifacts present in the image result in a loss of grayscale information that does not reveal the true value of fluorescence intensity. From the perspective of data post-processing, we propose a two-stage cell image recovery model based on generative adversarial network to solve the problem of phenotypic feature loss caused by saturation artifacts. The model is capable of restoring large areas of missing phenotypic features. In the experiment, we adopt the strategy of progressive restore to improve the robustness of the training effect, and add the contextual attention structure to enhance the stability of the restore effect. We hope to use deep learning methods to mitigate the effects of saturation artifacts to reveal how chemical, genetic, and environmental factors affect cell state, providing an effective tool for studying the field of biological variability and improving image quality in analysis.

The base excitation of mechanical equipment can result in pipeline system vibration which seriously affects the safe operation of the equipment. Particle damping technology is based on the particle collision dissipation principle to realize the structural vibration energy dissipation. This paper introduces the particle damping method into the vibration control of pipeline system. A particle damper has been designed for the structural characteristics of the pipeline. The influence of the material and structure of the pipeline particle damper, the external excitation and other parameters on the energy dissipation characteristics of particle damping are revealed. The energy dissipation mechanism of the pipeline particle collision damper under various parameter is analyzed. A pipeline vibration reduction test system with particle damping has been established. The effects of different excitation conditions, damper materials and number of unit structures of particle damper on the vibration damping effect of pipeline systems are investigated comparatively. The influence of damper parameters on the vibration suppression of pipeline system is obtained. The research in this paper can provide technical references for vibration suppression of pipeline systems.

A crucial component for developing an automated speaker or speech recognition system is voice preprocessing, which filters unwanted noise and detects the speech part. This study aimed to develop a computerized model to remove background noise and improve signal quality for future applications. This model was developed on a large longitudinal dataset containing varying real-world noise and validated on both a public dataset and a locally collected test dataset in different environments. An overall voice pre-processing pipeline is presented in this study, including denoising, segmentation, feature extraction, and ease of storage. The backbone of the denoising model is a Kalman filter, where the parameters were obtained from a grid search method; the signal-to-noise ratio (SNR) was used as the performance metric. Also, the segmentation was done to remove the pauses from the audio signal before the feature extraction. Finally, the data was stored as a template with the most common features. The SNR result suggested that the Kalman filter-based proposed method performed successfully across diverse datasets. Thus, this model provides a robust and adaptable solution for real-world scenarios and also ensures the data storing quality for future applications.

Ophthalmological services face global inadequacies, especially in low- and middle-income countries, which are marked by a shortage of both practitioners and equipment. This study employed a portable slit-lamp microscope with video capabilities and cloud storage for a more equitable global diagnostic resource distribution. To enhance accessibility and quality of care, this study targeted corneal opacity, a global cause of blindness. To boost the online diagnosis efficiency, an AI pipeline was developed using anterior segment videos to detect corneal opacity. First, we extracted image frames from videos and learned them using a Convolutional Neural Network(CNN) model. Second, we manually annotated to extract only the corneal margins, adjusted the contrast with CLAHE, and learned using the CNN model. Finally, we performed semantic segmentation of the cornea using the annotated data. The results showed an accuracy of 0.8 for image frames, and 0.96 for corneal margins. Dice and IoU were 0.94 for semantic segmentation of corneal margins. While corneal opacity detection from video frames seemed challenging in the early stages of this study, manual annotation, corneal extraction, and CLAHE contrast adjustment significantly improved accuracy. Integrating manual annotation into the AI pipeline through semantic segmentation achieved a high accuracy in detecting corneal opacity.

Reservoirs created by damming rivers significantly modify the environment and problems may arise: the storage of nutrients and organic matter in reservoirs often leads to decreased water quality due to eutrophication. Reservoirs built on lowland rivers are exposed to significant nutrient loads, often leading to eutrophication. In this article, the Sulejów Reservoir, in Central Poland, was the subject of the research, which focused on the use of Sentinel-2 remote sensing data to detect phytoplankton blooms, and on understanding the pattern of wind-driven surface currents using the CCHE2D model (a depth-averaged hydrodynamic model). The calculation of the total phosphorus load has shown that the reservoir mainly acts as nutrient storage. Still, during the low flow and intensive phytoplankton bloom, it can be a source of nutrients. The distribution of phytoplankton bloom on the Sulejów Reservoir was documented using eight Sentinel-2 satellite images from the vegetation season of 2020 and the Normalized Difference Chlorophyll Index (NDCl). Coupling remote sensing data and numerical modelling helps to interpret the hydrodynamic model results and understand nutrients and sediment dynamics within the reservoir. Hydrodynamic modelling combined with remote sensing data can be a valuable tool for selecting appropriate locations for water quality measurements at monitoring stations.

Catastrophic mass flows originating from the high mountain cryosphere often cause hazard cascades. With increasing human activities in the alpine region and the sensitivity of glaciers, snow and permafrost to climate warming, the cryospheric hazard risks tend to be more active in the Tibetan Plateau(TP). The remoteness and inaccessibility of high mountain regions make the remote sensing technology the most effective approach for monitoring and investigating the cryospheric hazards. Exploring the evolution process and impact of ice avalanches and subsequent hazards are crucial to understand drivers and nature of mass flow process chain in order to prevent and mitigate potential hazard consequences. In this study, the glacier and ice-rock avalanches occurred in Arutso and Sedongpu basins in Tibet were investigated on the basis of Sentinel-2 time-series images and in-situ investigation, the evolution process of these events were reconstructed, and impacts and driving factors were analyzed. The massive Chamoli rock-ice avalanche occurred in February 2021 in the western Himalayas was also reviewed using using same methods. The study shows that Arutso glacier No. 53 (Arutso-53) avalanche completely melted away in July 2018 after two years from occurrence to final disappearance, while Arutso glacier No. 50 (Arutso-50) avalanche completely melted by the end of August 2023 after lasting for seven years. Four large-scale ice-rock avalanche and debris flow events in the Sedongpu basin in 2017 and 2018 not only had significant impacts on the river flow, landscape and geomorphologic shape in the basin, but also caused serious disasters in the basin and downstream. In March 2021, a small-scale ice-rock avalanche and debris flow event occurred again in the Sedongpu basin. The glacier and ice-rock avalanches occurred in Tibet area were mainly induced by climate warming, heavy precipitation and seismic activity, which acting on specific topographic and geomorphic structure of glacier properties in the high mountain regions. Catastrophic hazard events originating from the high-elevation glacier and ice-rock collapses in the mountain cryosphere and subsequent hazard cascades in the TP and Himalayas highlight the importance of mountain hazard monitoring, early warning systems and sustainable mountain development.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

Vaginitis is a widespread issue for women worldwide, yet current diagnostic tools are lacking. Bacterial vaginosis (BV) is the most prevalent type of vaginitis, found in 10-50% of reproductive aged women. Current diagnostic methods for BV rely on clinical criteria, microscopy, or detection of a few microbes by qPCR. However, many vaginal infections lack a single etiological agent and are characterized by changes in the vaginal microbiome community structure (e.g. BV is defined as a loss of protective lactobacilli resulting in an overgrowth of anaerobic bacteria). Shotgun metagenomic sequencing provides a comprehensive view of all the organisms present in the vaginal microbiome (VMB) allowing for a better understanding of all potential etiologies. Here, we describe a robust VMB metagenomics sequencing test with a sensitivity of 93.1%, specificity of 90%, a negative predictive value of 93.4%, and a positive predictive value of 89.6% certified by Clinical Laboratory Improvement Amendments (CLIA), the College of American Pathologist (CAP) and the Clinical Laboratory Evaluation Program (CLEP). We sequenced over 7,000 human vaginal samples with this pipeline and described general findings and comparison to US census data.

The importance of detecting and diagnosing the imminence of aneurysm rupture before it occurs cannot be overstated. However, this process is often time-consuming and challenging, with variability in conclusions not uncommon among experts. Furthermore, current state-of-the-art models in medical image segmentation suffer from limited availability of large annotated datasets for training, exacerbated by an immense data imbalance. In most segmentation tasks, 3D segmentation is preferred due to its capacity to leverage more contextual information. However, these models require more data, which is constrained by the aforementioned issues. In the realm of current diagnosis models, those lacking geographic context are notably ineffective. To address these issues, the aim is to develop a model pipeline to accurately detect cerebral intracranial aneurysms and diagnose rupture imminence through 3D magnetic resonance angiography (MRA) and tabular input, augmented with the implementation of neuro-symbolic ai. The utilization of data fusion to tackle the lack of context in tabular models is proposed, leveraging extracted geographical features from a segmentation model. To enhance segmentation results and tackle the data imbalance in aneurysm segmentation, a two-stage model pipeline that extracts contextual geographic features before aneurysm segmentation is suggested. Segmentation results are additionally improved through ensemble techniques and novel preprocessing techniques. Finally, a neuro-symbolic aspect is introduced to enhance model diagnosis, interpretability and performance. The multi-step Integrated Neuro-Symbolic Analysis Pipeline for Cerebral Aneurysm Rupture Diagnosis is introduced.

Infant electrocardiograms (ECG) and heart rates (HR) are very useful biosignals for psychological research and clinical work, but can be hard to analyze properly, particularly long form (≥5 minutes) recordings taken in naturalistic environments. Infant HRs are typically much faster than adult HRs, and so some of the underlying frequency assumptions made about adult ECGs may not hold for infants. However, the bulk of publicly available ECG approaches focus on adult data. Here, existing open-source ECG approaches are tested on infant datasets. The best performing open-source method is then modified to maximize its performance on infant data (e.g., including a 15Hz high pass filter, adding local peak correction). The HR signal is then subsequently analyzed, developing an approach for cleaning data with separate sets of parameters for the analysis of cleaner and noisier HR. A Signal Quality Index (SQI) for HR is also developed, providing insight into where a signal is recoverable and where it is not, allowing for more confidence in analysis performed on naturalistic recordings. The tools developed and reported in this paper provide a base for future analysis of infant ECG and related biophysical characteristics. Of particular importance, the proposed solutions outlined here can be efficiently applied to real-world large datasets.

This study proposes self-calibration of capacitor mismatch errors for high-resolution pipeline analog-to-digital converters (ADCs). The proposed calibration circuit recursively amplifies the capacitor mismatch error by re-utilizing a multiplying digital-to-analog converter in a pipeline stage without increasing the circuit complexity, and the amplified error voltage is converted into digital code by utilizing the remaining pipeline stages. Error correction is performed by subtracting the digital code from the ADC output during normal operation. A prototype of a 12-bit pipeline ADC is fabricated in a 0.18 µm standard CMOS process. The ADC comprises eight 1.5-bit stages, followed by a 4-bit flash ADC as the final stage; the capacitor mismatch errors in the first two pipeline stages are corrected by utilizing the proposed self-calibration technique. At a sampling rate of 30 MS/s, the measured differential and integral nonlinearities improve from +0.82/-0.75 and +1.12/-1.79 to +0.45/-0.41 and +0.47/-0.91 after calibration, respectively. Further, the measured dynamic performances improve significantly with calibration. For an input frequency of 2.09 MHz, the ADC achieves a spurious-free dynamic range (SFDR) and signal-to-noise and distortion ratios (SNDR) of 69.3dB and 63.9dB before calibration, respectively. After calibration, the SFDR and SNDR increase to 84.1dB and 68.9dB, respectively, and the effective number of bits is approximately 11.1bit. The power consumption of the ADC is 35mW under 1.8V supply, and the resulting figure of merit is 514fJ/conversion step.

This paper provides a methodology for the production of synthetic images for training neural networks to recognise shapes and objects. There are many scenarios in which it is difficult, expensive and even dangerous to produce a set of images that is satisfactory for the training of a neural network. The development of 3D modelling software has nowadays reached such a level of realism and ease of use that it seemed natural to explore this innovative path and to give an answer regarding the reliability of this method that bases the training of the neural network on synthetic images. The results obtained in the two proposed use cases, that of the recognition of a pictorial style and that of the recognition of migrants at sea, leads us to support the validity of the approach, provided that the work is conducted in a very scrupulous and rigorous manner, exploiting the full potential of the modelling software. The code produced, which automatically generates the transformations necessary for the data augmentation of each image, and the generation of random environmental conditions in the case of Blender and Unity3D software, is available under the GPL licence on GitHub. The results obtained lead us to affirm that through the good practices presented in the article, we have defined a simple, reliable, economic and safe method to feed the training phase of a neural network dedicated to the recognition of objects and features, to be applied to various contexts.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

In the context of global climate change, the frequency of sudden natural disasters is increasing. Assessing traffic road damage post-disaster is crucial for emergency decision-making and disaster management. Traditional ground observation methods for evaluating traffic road damage are limited by the timeliness and coverage of data updates. Relying solely on these methods does not adequately support rapid assessment and emergency management during extreme natural disasters. Social media, a major source of big data, can effectively address these limitations by providing more timely and comprehensive disaster information. Motivated by this, we utilized multi-source heterogeneous data to assess the damage to traffic roads under extreme conditions and established a new framework for evaluating traffic roads in cities prone to flood disasters caused by rainstorms. The approach involves several steps: First, extracting the surface area affected by precipitation using a threshold method constrained by confidence intervals derived from microwave remote sensing images; Second, collecting disaster information from the Sina Weibo platform, where social media information is screened and cleaned. A quantification table for road traffic loss assessment was defined, and a social media disaster information classification model combining text convolutional neural networks and attention mechanisms was proposed (TextCNN-Attention Disaster Classification); Finally, matching traffic road information on social media with basic geographic data, visualizing the classification of traffic road disaster risk levels, and completing the assessment of traffic road disaster levels based on multi-source heterogeneous data. Using the "7.20" rainstorm event in Henan Province as an example, this study categorizes the disaster impact on traffic roads into five levels: particularly severe, severe, moderate, mild, and affected, as interpreted from remote sensing images. The evaluation framework for flood disaster traffic roads based on multi-source heterogeneous data provides important data support and methodological support for enhancing disaster management capabilities and systems.

The quality of wine depends upon the quality of the grapes, which, in turn, are affected by different viticulture aspects and the climate during the grape-growing season. Obtaining wine professionals’ judgments of the intrinsic qualities of selected wine products is a time-consuming task. It is also expensive. Instead of waiting for the wine to be produced, it is better to have an idea of the quality before harvesting, so that wine growers and wine manufacturers can use high-quality grapes. The main aim of the present study was to investigate the use of machine learning aspects in predicting wine quality and to develop a pipeline which represents the major steps from vineyards to wine quality indices. This pipeline outputs the predicted yield, values for basic parameters of grape juice composition, values for basic parameters of the wine composition, and quality. We also found that the yield could be predicted because of input data related to the characteristics of the vineyards. Finally, through the creation of a web-based application, we have investigated the balance berry yield and wine quality. Using these tools further developed, vineyard owners should be able to predict the quality of the wine they intend to produce from their vineyards before the grapes are even harvested.

Here is shown method for the hydraulic solution of a looped gas-pipeline networks. Calculation of presented network is done according to principles of Hardy Cross method. The optimization was carried out by iteration of the pipes diameters, node consumptions are known and flow velocities through pipes have to stand below certain values. Accent is on determination of appropriate friction factor, and on selection of representative equation for natural gas flow under presented conditions in the network. Inappropriate usage of friction factor, equally as inappropriate usage of gas flow equation can lead to inaccurate final results. Here is shown new facts in comparison to previous calculation of gas distribution network in Kragujevac, Serbia which is done in 1994. After the implementation, measurements in situ have performed, and real measured values deviate from calculated. Causes for these errors are investigated, and improved and more accurate procedure is shown.

Traditional underground pipeline inspection primarily relies on closed-circuit television (CCTV) systems, capturing visual data of deformations within sewer systems for manual assessment of their types and severity. However, these methods heavily rely on human expertise, which leads to subjective detection with limited accuracy. Moreover, they lack the capability for quantitative analysis of deformation extent, hindering accurate assessments and limiting overall inspection effectiveness. To address these challenges, this paper proposes a method for quantitatively detecting geometric deformations in underground pipe corridors using laser point cloud data. The approach, employing laser scanning with a 3D scanner, enables objective detection of internal pipeline deformations and quantitative assessment of blockage levels. In comparison to traditional CCTV-based methods, this approach offers advantages in objectivity and quantification, thereby improving detection reliability, accuracy, and overall efficiency.

Trailing oil is the tail section of contamination. There are two main reasons for the formation of trailing oil, one is the effect of laminar flow boundary layer, the other is the outflow of the preceding batch remained in the dead-legs. In the batch transportation of refined oil, under the action of viscous force, the preceding batch forms laminar boundary layer near the pipe wall and stays on the pipe wall, resulting in the phenomenon of contamination trailing and formation of trailing oil. When oil passes through the valve chamber of the oil transportation station, dead-leg will be formed. Due to gravity and convection diffusion, preceding batch flowing from dead-legs will form trailing oil in the pipeline. The phenomenon of trailing oil exists in the process of batch transportation, which will have an effect on the quality of oil. In this paper, Reynolds time-averaged method is used to simulate turbulence.Computational Fluid Dynamics(CFD) software is used to simulate different flow rates and bypass lengths to obtain contamination-related experimental data.Matlab software is used to perform multi-nonlinear regression for the oil substitution time, the length of the bypass and the flow rate. The formula for calculating the length of the trailing oil produced by the dead-leg is obtained. The modified formula for calculating the length of the contamination is obtained by combining the existing formula for calculating the length of the contamination.

This paper shows a method for pipeline leak detection using a transient-based method with MATLAB® functions. The simulation of a pipeline systems in the time domain are very complex. In the case of the dissipative model, transfer functions are hyperbolic Bessel functions. Simulating a pipeline system in the frequency domain using a dissipative model we could find an approximate transfer function with equal frequency domain response to in order get the pipeline system's time domain response. The method described in this paper can be used to detect, by comparison, to detect a leak in a pipeline system model.

During the last 25 years the scientific community has coexisted with the most fascinating protocol due to Quantum Physics: quantum teleportation (QTele), which would have been impossible if quantum entanglement, so questioned by Einstein, did not exist. In this work, a complete architecture for the teleportation of Computational Basis States (CBS) is presented. Such CBS will represent each of the possible 24 classical bits commonly used to encode every pixel of a 3-color-channel-image (red-green-blue, or cyan-yellow-magenta). For this purpose, a couple of interfaces: classical-to-quantum (Cl2Qu) and quantum-to-classical (Qu2Cl) are presented with two versions of the teleportation protocol: standard and simplified.

Semantic segmentation of high-resolution remote sensing images provides detailed and precise feature information, playing a pivotal role in decision-making and analysis in sectors such as water management, agriculture, military, and environmental protection. However, most methods merely combine features from various branches directly, without a mechanism for spatial location feature screening, and treat all extracted features as equally important. To overcome these limitations, we introduce a novel spatially adaptive interaction network (SAINet) for dynamic interaction across different features in remote sensing semantic segmentation task. Specifically, we propose a spatial refined module that leverages local context information to filter spatial locations and extract salient regions. Following this, we introduce an innovative spatial interaction module that uses a spatial adaptive modulation mechanism to dynamically select and allocate spatial position weights. This facilitates interaction between local salient areas and global information, allowing the network to focus more on relevant regions. This flexible approach enables the network to capture more informative features, thereby enhancing segmentation accuracy. Experiments conducted on the DeepGlobe, Vaihingen, and Potsdam public datasets confirm the effectiveness and capability of SAINet. Our code and models will be publicly available

The rapid spread of African swine fever virus (ASFV), causing severe and often lethal disease in domestic pigs and Eurasian wild boar, continues to be a threat for pig populations and dependent industries. Despite scientific achievements that deepen our understanding of ASFV pathogenesis, alternative transmission routes for ASFV remain to be elucidated. We previously demonstrated the efficient transmission of ASFV from infected boars to naïve recipient gilts via artificial insemination, thereby highlighting the importance of surveillance in boar semen prior to shipment. Since accurate and reliable detection of even low amounts of ASFV in boar semen is key for disease prevention and control, we established a suitable diagnostic pipeline to efficiently detect ASFV genome in boar semen. Here, we assessed sensitivity, specificity and overall performance of various routine nucleic acid extraction kits as well as qPCR protocols in detecting ASFV genome in blood and semen of boars. Feasibility of respective kits and methods for future use in boar studs was also considered. Variability in sensitivity mostly concerned samples with low to very low amounts of ASFV genome. Ultimately, we defined a well-suited pipeline to precisely detect ASFV genome in boar semen, as early as 2 days post ASFV infection.

We apply the Canny Edge algorithm to the Utqiaġvik coastal sea ice radar system (CSIRS) to quantify open water and sea ice (landfast or drifting) concentration. The radar-derived sea ice concentration is compared against the 25-km resolution NSIDC Climate Data Record (CDR, one pixel closest to the radar field of view) and the 1-km merged MODIS-AMSR2 sea ice concentrations in the ∼11 km field of view for the year 2022-2023, when improved image contrast was first implemented. The algorithm was first optimized using sea ice concentration from 14 different images and 10 ice analysts (140 analysis in total) covering a wide range of ice condition with landfast ice, drifting ice and open water. The algorithm is also validated quantitatively against high-resolution MODIS-Terra in the visible range. Results show a correlation coefficient and mean bias error between the optimized algorithm, the CDR and MODIS-AMSR2 daily SIC of 0.18 and 0.54, and ∼ -1 and 0.9%, respectively, with an averaged inter-analyst error of ± 3%. In general, the CDR captures the melt period correctly and overestimates the SIC during the winter and freeze-up period, while the merged MODIS-AMSR2 better captures the punctual break-out events in winter including those during the freeze-up events (reduction of in SIC). Remnant issues with the detection algorithm include the false detection of sea ice in the presence, fog or precipitation (up to 20%), quantified from the summer reconstruction with known open water conditions. Coastal marine radars provide prove very useful in bridging the gap between (lower) resolution satellite-derived and in-situ (visual) sea ice conditions, and to quantify land contamination from lower resolution satellite-derived SIC.

The advent of deep learning (DL) has revolutionized medical imaging, offering unprecedented avenues for accurate disease classification and diagnosis. DL models have shown remarkable promise for classifying brain tumor from Magnetic Resonance Imaging (MRI) scans. However, despite their impressive performance, the opaque nature of DL models poses challenges in understanding their decision-making processes, particularly crucial in medical contexts where interpretability is essential. This paper explores the intersection of medical image analysis and DL interpretability, aiming to elucidate the decision-making rationale of DL models in brain tumor classification. Leveraging state-of-the-art DL frameworks with transfer learning, we conduct a comprehensive evaluation encompassing both classification accuracy and interpretability. Using state-of-the-art DL frameworks with transfer learning, we conduct a thorough evaluation covering both classification accuracy and interpretability. We employ adaptive path-based techniques to understand the underlying decision-making mechanisms of these models. Grad-CAM and Grad-CAM++ highlight critical image regions where the tumors are located.

This study focuses on enhancing the prediction of flow characteristics in gas pipelines under hydrate-forming conditions using a validated CFD model. Four-Quadrants approach was introduced to analyse the relationship between gas and water flowrates, and to provide further insights into hydrate formation, agglomeration, deposition, and pipeline plugging. The analysis considered subcooling temperatures, water volume fractions, and gas velocities, to assess the risk of hydrate plugging in subsea gas pipelines. Results indicate that higher subcooling temperatures significantly increase the risk of hydrate formation and plugging, especially at lower gas velocities. At subcooling temperatures above 7.1 K, hydrate agglomeration and deposition become more pronounced, leading to a greater risk of plugging. Similarly, water volume fractions above 0.06 were found to increase the likelihood of hydrate blockages. However, higher gas velocities were shown to reduce this risk by promoting the sloughing of hydrates and preventing deposition. The findings align with existing literature and offer practical insights for flow assurance in gas pipeline operations.

Next-generation sequencing is now a mature technology, allowing partial animal genomes to be produced for many clades. Though many software exist for genome assembly and annotation, a simple pipeline that allows researchers to input raw sequencing reads in fastq format and allow the retrieval of a completely assembled and annotated mitochondrial genome is still missing. mitoMaker 1.0 is a pipeline developed in python that implements (i) recursive de novo assembly of mitochondrial genomes using a set of increasing k-mers; (ii) search for the best matching result to a target mitogenome and; (iii) performs iterative reference-based strategies to optimize the assembly. After (iv) checking for circularization and (v) positioning tRNA-Phe at the beginning, (vi) geneChecker.py module performs a complete annotation of the mitochondrial genome and provides a GenBank formatted file as output.

This study introduces SkinLiTE, a lightweight supervised contrastive learning model, tailored to enhance the detection and typification of skin lesions in dermoscopic images. The core of SkinLiTE lies in its unique integration of supervised and contrastive learning approaches, which leverages labeled data to learn generalizable representations. This approach is particularly adept at handling the complexities and imbalances inherent in skin lesions datasets. The methodology encompasses a two-phase learning process. In the first phase, SkinLiTE utilizes an encoder network and a projection head to transform and project dermoscopic images into a feature space where contrastive loss is applied, focusing on minimizing intra-class variations while maximizing inter-class differences. The second phase freezes the encoder's weights, leveraging the learned representations for classification through a series of dense and dropout layers. The model was evaluated using three datasets from Skin Cancer ISIC 2019-2020, covering a wide range of skin conditions. SkinLiTE demonstrated superior performance across various metrics—accuracy, AUC , and F1 score—particularly when compared with traditional supervised learning models. Notably, SkinLiTE achieved an accuracy of 0.9087 using AugMix augmentation for binary classification of skin lesions. It also showed comparable results with the state-of-the-art approaches of ISIC challenge without relying on external data, underscoring its efficacy and efficiency. The results highlight the potential of SkinLiTE as a significant step forward in the field of dermatological AI, offering a robust, efficient, and accurate tool for skin lesion detection and classification. Its lightweight architecture and ability to handle imbalanced datasets make it particularly suited for integration into Internet of Medical Things environments, paving the way for enhanced remote patient monitoring and diagnostic capabilities. This research contributes to the evolving landscape of AI in healthcare, demonstrating the impact of innovative learning methodologies in medical image analysis.

Sentinel-2 can provide multi-spectral optical remote sensing images in RGBN bands with a spatial resolution of 10m, but the spatial details provided are not enough for many applications. WorldView can provide HR multi-spectral images less than 2m, but it is a commercial paid resource with relatively high usage costs. In this paper, without any available reference images, Sentinel-2 images at 10m resolution are improved to a resolution of 2.5m through super-resolution (SR) based on deep learning technology. Our model, named DKN-SR-GAN, uses degradation kernel estimation and noise injection to construct a dataset of near-natural low-high-resolution (LHR) image pairs, with only low-resolution (LR) images and no high-resolution (HR) prior information. DKN-SR-GAN uses the Generative Adversarial Networks (GAN) combined of ESRGAN-type generator, PatchGAN-type discriminator and the VGG-19-type feature extractor, using perceptual loss to optimize the network, so as to obtain SR images with clearer details and better perceptual effects. Experiments demonstrate that in the quantitative comparison of the non-reference image quality assessment (NR-IQA) metrics like NIQE, BRISQUE and PIQE, as well as the intuitive visual effects of the generated images, compared with state-of-the-art models such as EDSR8-RGB, RCAN and RS-ESRGAN, our proposed model has obvious advantages.

Ondol, a heating system unique to Korean homes, raises indoor temperatures by supplying hot water through pipes embedded in the floor slab. Known for its comfort and sustained heat advantages, Ondol has garnered international interest in countries requiring efficient heating solutions. Given the inherent challenges during installation and operation, timely inspection is crucial due to difficulties in detecting and pinpointing defects in the buried concrete pipes, often leading to costly rework and removal. Yet, specialized inspection systems tailored for Ondol pipes remain underexplored. Therefore, this study proposes a robotic inspection system capable of assessing the condition of Ondol pipelines. We analyzed the characteristics of Ondol piping to establish the system requirements and developed a prototype of a compact capsule-shaped inspection robot tailored for Ondol pipe inspection. Subsequent laboratory testing validated its performance and usability, confirming its capability for field application through tests on curvature maneuverability and image reception quality. This research aims to motivate advancements in Ondol-specific system implementation and performance validation, potentially contributing to the smartification of Ondol maintenance practices.

InSAR and associated analytic methods can measure surface deformation from low earth orbit with a claimed accuracy of centimeters to millimeters. The realized accuracy depends on the area being measured and on the choice of analytic method, suggesting one choose a method in response to the area being measured. Here we consider a specific fixed analytic method and compare the results it produces to measurements gathered from other means in a variety of settings. In particular we compare Sentinel-1 InSAR with GPS at the Kilauea volcano around the 2018 eruption, with GPS in the city of Arica, Chile, and with public survey data at a decommissioned tailings mine. In addition, we compare two independent Sentinel-1 InSAR analyses for a railway station in Oslo, Norway. Our goal is estimate the accuracy of a fully automated Sentinel-1 InSAR pipeline in various settings. Our conclusions are that centimeter level accuracy is a reasonable claim in many, but not all settings, and that accuracy is typically not lost by using an automated pipeline, instead of hand-selecting and tuning parameters.

Medical brain image analysis is a necessary step in the Computers Assisted /Aided Diagnosis (CAD) systems. Advancements in both hardware and software in the past few years have led to improved segmentation and classification of various diseases. In the present work, we review the published literature on systems and algorithms that allow for classification, identification, and detection of White Matter Hyperintensities (WMHs) of brain MRI images specifically in cases of ischemic stroke and demyelinating diseases. For the selection criteria, we used the bibliometric networks. Out of a total of 140 documents we selected 38 articles that deal with the main objectives of this study. Based on the analysis and discussion of the revised documents, there is constant growth in the research and proposal of new models of deep learning to achieve the highest accuracy and reliability of the segmentation of ischemic and demyelinating lesions. Models with indicators (Dice Score, DSC: 0.99) were found, however with little practical application due to the uses of small datasets and lack of reproducibility. Therefore, the main conclusion is to establish multidisciplinary research groups to overcome the gap between CAD developments and their complete utilization in the clinical environment.

Condition monitoring is a crucial process for ensuring industrial assets' reliability and operational efficiency. In the age of the digital industry, AI-based data-driven condition monitoring is proving extremely effective in detecting potential issues before they escalate into major problems, thereby reducing downtime, minimizing maintenance costs, and extending the lifespan of the equipment. The availability of tools that can enable the operationalization of these data-driven solutions is, therefore, critical. In this direction, this work proposes a comprehensive, modular, and scalable pipeline covering all the steps from the data acquisition to the AI model training and inference phases. The tool integrates the data acquisition and processing steps with a configurable feature extraction phase. Moreover, the system also integrates deep learning algorithms for diagnosis and prognosis, including a domain adaptation stage to permit transfer learning and increase generalizability. In addition, it features a communication system using MQTT, which allows for an online data stream to enable real-time monitoring and maintenance. The overall infrastructure was deployed in actual industrial settings and tested in a real-time experiment, demonstrating the proposed approach's validity.

The purpose of this study was to identify candidate novel species performing beneficial ecological functions from soil. The hypothesis was that novel culturable species with antibiotic production potential could be readily found from soil in the Nature Canyon at Los Angeles Pierce College. 137 bacterial isolates from soil were grown on nutrient agar, ISP-6 medium, or LB agar and partial 16S was ascertained using the Sanger platform for regions V1-V4. One of the potentially novel isolates, Pseudomonas sp. 21-C3-ER, was isolated on nutrient agar from fallow soil in an agricultural nature preserve in Los Angeles. The soil conditions were 3.7% moisture, clay texture by touch, 13.37% organic matter, pH=6.63, TDS=638, 150 ppm nitrogen, 114 ppm phosphate, and 42 ppm potash. Whole genome sequencing was performed on the DNBseq platform and species identification was performed with TRUEBacID; the closest relative was Pseudomonas brassicacearum subsp. neoaurantiaca which was 92.05% similar by genomic evidence. 197 virulence factors were identified including flagellar biosynthesis, motor proteins, Beta-lactamase, Fosfomycin, copper, and sulfur drug resistance. Gram stain of strain 21-C3-ER revealed gram negative rods. Rods were visualized with scanning electron microscopy, revealing individuals approximately 1 µm in length. Secondary metabolite analysis using antiSMASH showed a variety of post-translationally modified proteins and a promysalin analog. The qualitative test for pyoverdine siderophore production using UV light was positive. Metabolic analysis using RAST indicated genes were present for pyoverdine production, antimicrobial resistance, and ammonification. The nitrate reduction test was positive. Denitrifying bacteria may prevent leaching of nitrates from soil, since ammonia has a higher affinity to soil and organic matter than nitrate. We propose Pseudomonas fernandeno as a novel species. The type stain is 21-C3-ER.

Certain configurations of liquefied natural gas refueling stations exhibit a deficiency in managing boil-off gas. Furthermore, the ill-conceived linkage between the submersible pump and the gas storage tank pipeline leads to impeded natural gas transmission. This study employs Computational Fluid Dynamics (CFD) methodology to scrutinize the hydrodynamic attributes of T-type tee and dovetail tee configurations implemented in the pipeline design connecting the submersible pump and storage tank in an LNG filling station across diverse operational scenarios. The T-type tee induces detachment of the primary flow from the inner wall due to inertial forces, resulting in vortex formation and heightened resistance, accompanied by increased energy dissipation. Conversely, the dovetail tee, with its circular wall transition, mitigates vortex generation, reducing the separation zone and consequently minimizing resistance and energy loss. The maximum static differential pressure between the inlet and outlet of the dovetail tee is diminished by 52.52% when compared to that of the T-type tee. In the most noteworthy scenarios, the local resistance coefficient of the dovetail tee is even less than 1/10 of that of the T-type tee. In practical engineering applications, the incorporation of dovetail tees leads to a 17.58% reduction in the required elevation difference. This results in a more uniform flow field and enhanced stability in both flow rate and pressure. Such improvements contribute to heightened engineering efficiency and environmental sustainability, particularly evident in the design of LNG filling stations.

To date, the development of unmanned technologies using autonomous underwater vehicles (AUV) has become an urgent demand for solving the problem of inspection of industrial sub-sea structures. A key issue here is precise localization of AUVs relative to underwater objects. However, the well-known challenges of recognizing and coordinating underwater objects (impossibility to use GPS, undercurrents, etc.) do not allow high-precision navigation if based solely on a standard suite of AUV navigation tools (sonars, etc.). An alternative is a technology of processing of optical images that, at short distances, can provide higher accuracy of AUV navigation compared to a technology of acoustic measurement processing. In this study, in the context of the problem of subsea production system inspection, we propose a method to recognize underwater objects and provide coordinate reference of AUV to them, based on stereo-image processing. Its distinctive features are the use of a non-standard technique for generating a geometric model of an object from its views (foreshortening) taken from positions of a pre-made overview trajectory, the use of various characteristic geometric elements when recognizing objects, and the original algorithms for comparing visual data of the inspection trajectory with an a priori model of the object.

The previous studies on the diversion pipe of pumped storage power stations (PSPS) primarily focused on numerical simulations of pulsating pressure propagation within the pipe and its inducing factors. However, there was a lack of field monitoring and analysis of measured data to support surface ambient vibration, resulting in insufficient credibility and practicality of the numerical results. Based on ambient monitoring and data analysis, this paper examines the factors contributing to the ambient vibration of the water diversion pipeline in Changlongshan (CLS) PSPS. It is concluded that: (1) The primary source of vibration originates from units operation-induced ambient vibrations; (2) Vibration during pumping conditions exceeds that during power generation conditions; (3) The ground measuring point's vibration acceleration primarily depends on the distance from the vibration source; (4) Different types of units have varying effects on water diversion pipeline vibrations.

In the neuroscience research field, specific for medical imaging analysis, how to mining more latent medical information from big medical data is significant for us to find the solution of diseases. In this review, we focus on neuroimaging data that is functional Magnetic Resonance Imaging (fMRI) which non-invasive techniques, it already becomes popular tools in the clinical neuroscience and functional cognitive science research. After we get fMRI data, we actually have various software and computer programming that including open source and commercial, it's very hard to choose the best software to analyze data. What's worse, it would cause final result imbalance and unstable when we combine more than software together, so that's why we want to make a pipeline to analyze data. On the other hand, with the growing of machine learning, Python has already become one of very hot and popular computer programming. In addition, it is an open source and dynamic computer programming, the communities, libraries and contributors fast increase in the recent year. Through this review, we hope that can make neuroimaging data analysis more easy, stable and uniform base the one platform system.

The exceptional increase in molecular DNA sequence data in open repositories is mirrored by an ever-growing interest among evolutionary biologists to harvest and use those data for phylogenetic inference. Many quality issues, however, are known and the sheer amount and complexity of data available can pose considerable barriers to their usefulness. A key issue in this domain is the high frequency of sequence mislabelling encountered when searching for suitable sequences for phylogenetic analysis. These issues include the incorrect identification of sequenced species, non-standardised and ambiguous sequence annotation, and the inadvertent addition of paralogous sequences by users, among others. Taken together, these issues likely add considerable noise, error or bias to phylogenetic inference, a risk that is likely to increase with the size of phylogenies or the molecular datasets used to generate them. Here we present a software package, phylotaR, that bypasses the above issues by using instead an alignment search tool to identify orthologous sequences. Our package builds on the framework of its predecessor, PhyLoTa, by providing a modular pipeline for identifying overlapping sequence clusters using up-to-date GenBank data and providing new features, improvements and tools. We demonstrate our pipeline’s effectiveness by presenting trees generated from phylotaR clusters for two large taxonomic clades: palms and primates. Given the versatility of this package, we hope that it will become a standard tool for any research aiming to use GenBank data for phylogenetic analysis.

This paper provides orthogonal moments (OM) such as, Zernike Moments(ZM), Psuedo Zernike Moments(PZM) and Orthogonal Fourier Mellin Moments(OFMM) for the analysis of melanoma images. The moment invariants may vary with respect to geometric variations. For the analysis of orthogonal moments hundred random melanoma images and hundred non-melanoma images have been taken into consideration from the database of 570 melanoma images and 250 non-melanoma images respectively. Orthoganal moments have been computed by varying the phase angles from 10° to 40° with an equal interval of 10° degree for the orders 2, 4,8,16,32,64,128,256 respectively. For the optimal OMs Particle Swarm Optimization (PSO) technique have been used. These set of extracted optimal OMs have been further applied to classify melanoma images. Support Vector Machine (SVM) has been used for the classification of [1]sensitivity=88.78%.

The application of deep learning algorithms to predict the molecular profiles of various cancers from digital images of hematoxylin and eosin (H&E)-stained slides has been reported in recent years, mainly in gastric and colon cancers. In this study, we investigated the potential use of H&E-stained endometrial cancer slide images to predict the associated mismatch repair (MMR) status. H&E-stained slide images were collected from 127 cases of the primary lesion of endometrial cancer. After digitization using a Nanozoomer virtual slide scanner (Hamamatsu Photonics), we segmented the scanned images into 5,397 tiles of 512 × 512 pixels. The MMR proteins (PMS2, MSH6) were immunohistochemically stained, classified into MMR proficient/deficient, and annotated for each case and tile. We trained several neural networks, including convolutional and attention-based networks, using tiles annotated with the MMR status. Among the tested networks, ResNet50 exhibited the highest area under the receiver operating characteristic curve (AUROC) of 0.91 for predicting the MMR status. The constructed prediction algorithm may be applicable to other molecular profiles and useful for pre-screening before implementing other, more costly genetic profiling tests.

Considering animal welfare, the free-range laying hen farming model is increasingly gaining attention. However, in some countries, large-scale farming still relies on the cage-rearing model, making the focus on the welfare of caged laying hens equally important. To evaluate the health status of caged laying hens, a dataset comprising visible light and thermal infrared images was established for analyses, including morphological, thermographic, comb, and behavioural as-sessments, enabling a comprehensive evaluation of the hens' health, behaviour, and population counts. To address the issue of insufficient data samples in the health detection process for indi-vidual and group hens, a dataset named BClayinghens was constructed containing 61,133 images of visible light and thermal infrared images. The BClayinghens dataset was completed using three types of devices: smartphones, visible light cameras, and infrared thermal cameras. All thermal infrared images correspond to visible light images and have achieved positional alignment through coordinate correction. Additionally, the visible light images were annotated with chicken head labels, obtaining 63,693 chicken head labels, which can be directly used for training deep learning models for chicken head object detection and combined with corresponding thermal infrared data to analyze the temperature of the chicken heads. To enable the constructed deep-learning object detection and recognition models to adapt to different breeding environ-ments, various data enhancement methods such as rotation, shearing, colour enhancement, and noise addition were used for image processing. The BClayinghens dataset is important for ap-plying visible light images and corresponding thermal infrared images in the health detection, behavioural analysis, and counting of caged laying hens under large-scale farming.

The Fractal Analysis of Medical Images is an investigation field in those that numerous results of important value have been obtained. This work describes the basic foundations of the Fractal Analysis and its application has more than enough medical images, leaning on in five scientific investigations.

An image consisting of (m, n) pixels can be seen as a matrix of m × n size. Based on the formula of angles between two subspaces, a pair of angles can be defined between two matrices, by utilizing column spaces and row spaces of the two matrices. The singular values of each matrix can be used to calculate distances. Thus, a distance representation is obtained, and a pair of angles between 2 matrices of the same size.

Hyperspectral imaging provides vital information about the objects and elements present inside the image. That’s why they are very useful in satellite imagery as well as image forensics. Hyperspectral document analysis (HSDI) can be used for document authentication using ink analysis which can provide sufficient information about the composition and type of ink. In this project, we have implemented HSDI based ink classification technique using Principle Component Analysis for dimensionality reduction and K-means clustering for ink classification. This is unsupervised learning approach and it is very simple and efficient in order to classify limited number of bands. We have used this technique to classify 33 different bands of ink.

Chicory, a horticultural crop cultivated worldwide, presents many botanical varieties and local biotypes. Among these, Italian radicchio group cultivars of pure Cichorium intybus L. and interspecific hybrids with Cichorium endivia L., as the “Red of Chioggia” biotype which in turn includes several phenotypes. This study deals with a pipeline for the marker-assisted breeding of F1 hybrids: it presents the genotyping-by-sequencing results of four elite inbred lines using a RADseq approach and an original molecular assay based on CAPS markers for screening mutants with nuclear male-sterility in radicchio of Chioggia. Two thousand nine hundred fifty-three SNP-carrying RADtags were identified and used to compute the actual estimates of homozygosity, and overall genetic similarity and uniformity of the populations, as well as to determine their genetic distinctiveness and differentiation. Molecular data were further used to investigate the genomic distribution of the RADtags among the two Cichorium species, allowing their mapping in 1,131 and 1,071 coding sequences in chicory and endive, respectively. In parallel, an assay to screen the genotype at the male-sterility locus Cims-1 was developed to discriminate wild-type and mutant alleles of the causative gene myb80-like. Moreover, a RADtag mapped close to this genomic region proved the potential application of this method for future marker-assisted selection tools. Finally, combining the genotype information of the core collection, the best ten individuals from each inbred line were selected to compute the observed genetic similarity as a measure of uniformity as well as the expected homozygosity and heterozygosity estimates scorable by the putative progenies derived from selfing (pollen parent) and full-sibling (seed parent) or pair-wise crossing (F1 hybrids). This predictive approach was conducted as a pilot study for understanding the potential application of RADseq in improving molecular breeding strategies aimed at the development of inbred lines and F1 hybrids in leaf chicory.

This paper presents MADS (Multi-Agents for Data Science), an innovative and simple open-source multi-agent framework designed for systemic pipeline execution in applied supervised machine learning. By leveraging the capabilities of multi-agent systems (MAS), we introduce a universal approach to optimize and streamline machine learning pipelines. Our framework highlights the differences between various types of agents, such as reinforcement learning (RL) agents and large language model (LLM) agents, and their distinct contributions to the process. While we currently employ LLM agents to automate and enhance machine learning tasks, we acknowledge the potential of incorporating RL agents in future iterations to further improve performance and adaptability. The primary objective is to enhance the efficiency, scalability, and adaptability of supervised learning applications across various domains. This integration addresses the complexity and manual effort typically associated with machine learning workflows, paving the way for more automated, robust, and scalable solutions. Our approach demonstrates significant improvements in task automation, reduced human intervention, and enhanced model performance. The MADS framework, which will soon be available as an open-source implementation, represents a pivotal contribution to the field of machine learning, promising to facilitate broader adoption and collaborative advancement.

Extensive, but remote oil and gas fields of the United States, Canada, and Russia require the construction and operation of extremely long pipelines. Global warming and local heating effects lead to rising soil temperatures and thus a reduction in the sub-grade capacity of the soils; this causes changes in the spatial positions and forms of the pipelines, consequently increasing the number of accidents. Oil operators are compelled to monitor the soil temperature along the routes of the remoted pipelines in order to be able to perform remedial measures in time. They are therefore seeking methods for the analysis of volumetric diagnostic information. To forecast soil temperatures at the different depths we propose compiling a multidimensional dataset, defining descriptive statistics; selecting uncorrelated time series; generating synthetic features; robust scaling temperature series, tuning the additive regression model to forecast soil temperatures.

Endoscopic medical images can suffer from uneven illumination, low contrast, and lack of texture information due to the use of point directional light sources and the presence of narrow tissue structures, posing diagnostic difficulties for physicians. In this paper, a deep learning-based su-pervised illumination enhancement network is designed for low-light endoscopic images, aiming to improve both global illumination and local details. Initially, a global illumination enhancement module is formulated utilizing a higher-order curve function to improve global illumination. Sec-ondly, a local feature extraction module incorporating dual attention is designed to capture local detailed features. Considering the significance of color fidelity in biomedical scenarios, the designed loss function prioritizes introducing color loss to alleviate image color distortion. Compared with seven state-of-the-art enhancement algorithms on Endo4IE endoscopic datasets, experimental re-sults show that the proposed method can better enhance low-light endoscopic images and avoid image color distortion. It provides an efficient method to enhance images captured by endoscopes which can effectively assist clinical diagnosis and treatment.

With the development of economy, maritime transportation has increased rapidly, which has had a significant impact on the marine environment and resources. In recent years, Synthetic Aperture Radar (SAR) has been widely used to observe maritime environmental incident. Through the large coverage area of SAR, marine environmental emergencies, especially oil pollution, can be better monitored and responded to. This study first proposed an improved Full-scale Aggregated MobileUNet (FA-MobileUNet) model to achieve more complete detection results of oil spill areas. The convolutional block attention module (CBAM) in FA-MobileUNet was modified based on morphological concepts. By introducing the morphological attention module (MAM), the improved FA-MobileUNet model can reduce the fragments and holes in the detection results, providing complete oil spill areas which were more suitable for describing the location and scope of oil pollution incidents. In addition, to overcome the inherent category imbalance of the dataset, label smoothing was applied in model training to reduce the model’s overconfidence in majority class samples while improving the model’s generalization ability. The detection performance of the improved FA-MobileUNet model reached 84.55% mIoU (mean Intersection over Union), which was 17.15% higher than that of the original U-Net model. The improved FA-MobileUNet model was then examined by some oil pollution incidents. According to the detection results, if the oil spill was suspected to be caused by a ship, the corresponding Automatic Identification System (AIS) data were collected based on the acquisition time and geo-location of the SAR image to search for the ship suspected of causing oil pollution. Finally, some oil pollution incidents in Taiwan marine area were collected to verify the effectiveness of the proposed model for marine oil pollution monitoring. Experimental results showed that the extent of the detected oil spill was consistent with the oil pollution area recorded in the incident reports.

The subway station operation is susceptible to safety accidents when high-pressure gas pipeline overlaying, and analyzing the correlations between the safety influencing factors (SIFs) under this operation situation can provide paths to reduce safety accidents. Thus, this paper investigated the coupling correlations between the SIFs. We firstly identified the SIFs during subway station operation under high-pressure pipeline (SSOUHP) based on the literature review and experts’ discussion. Then, the analytic hierarchy process (AHP) and coupling degree analysis (CDA) were combined to assess the coupling correlations between the SIFs. And Y subway station was selected to test the proposed hybrid coupling analysis approach. Research results show that (a) 23 second-level SIFs were identified and these SIFs can be summed up into 5 first-level SIFs, namely, human-related SIFs, pipeline-related SIFs, station-related SIFs, environment-related SIFs, and management-related SIFs; (b) the proposed hybrid approach can be used to evaluate the coupling correlations between SIFs; (c) of the coupling situations during Y subway station operation, the internal coupling correlations among environment-related SIFs, the coupling correlations between pipe-related SIFs and environment-related SIFs, and the coupling correlations among human-related SIFs, pipe-related SIFs and environment-related SIFs are with higher safety risk; (d) the overall coupling correlation among all SIFs during Y subway station operation is with lower safety risk. The research can enrich the knowledge in the safety evaluation area, and provide reference for onsite safety management.

While there are millions of reptile images available online, they are not well organized and not easily findable, accessible, interoperable, or reproducible (FAIR). More importantly, they are not standardized and thus hardly comparable. Here we present a reference database of more than 14,000 standardized images of 1,045 reptile species (969 lizard and 76 snake species), that are based on preserved specimens in 20 different collections, including 533 type species of genera and type specimens of 72 species. All images were taken with standardized views, including dorsal and ventral body shots as well as dorsal, ventral, and lateral views of the heads and other body parts. Although only 11 out of the 20 collections are cross-referenced in Vertnet, some others are indexed in GBIF, and this fraction will certainly grow in the near future. The utility of this and similar image collections will further grow with additional material and further cross-referencing, e.g., to DNA sequence databases or citizen science projects. The images are searchable and freely available on Morphobank.org (Project 5121) and on Figshare.com.

The evolution in imaging technologies and artificial intelligence algorithms, coupled with improvements in UAV technology, has enabled the use of unmanned aircraft in a wide range of applications. The feasibility of this kind of approach for cattle monitoring has been demonstrated by several studies, but practical use is still challenging due to the particular characteristics of this application, such as the need to track mobile targets and the extensive areas that need to be covered in most cases. The objective of this study was to investigate the feasibility of using a tilted angle to increase the area covered by each image. Deep Convolutional Neural Networks (Xception architecture) were used to generate the models for the experiments, which covered aspects like ideal input dimensions, effect of the distance between animals and sensor, effect of classification error on the overall detection process, and impact of physical obstacles on the accuracy of the model. Experimental results indicate that oblique images can be successfully used under certain conditions, but some practical limitations need to be addressed in order to make this approach appealing.

Event-based vision is an emerging field of computer vision that offers unique properties such as asynchronous visual output, high temporal resolutions, and dependence on brightness changes to generate data. These properties can enable robust high-temporal-resolution object detection and tracking when combined with frame-based vision. In this paper, we present a hybrid, high-temporal-resolution, object detection and tracking approach, that combines learned and classical methods using synchronized images and event data. Off-the-shelf frame-based object detectors are used for initial object detection and classification. Then, event masks, generated per each detection, are used to enable inter-frame tracking at varying temporal resolutions using the event data. Detections are associated across time using a simple low-cost association metric. Moreover, we collect and label a traffic dataset using the hybrid sensor DAVIS 240c. This dataset is utilized for quantitative evaluation using state-of-the-art detection and tracking metrics. We provide ground truth bounding boxes and object IDs for each vehicle annotation. Further, we generate high-temporal-resolution ground truth data to analyze the tracking performance at different temporal rates. Our approach shows promising results with minimal performance deterioration at higher temporal resolutions (48 – 384 Hz) when compared with the baseline frame-based performance at 24 Hz.

Treating central giant cell granuloma (CGCG) is challenging due to high recurrence rates and variable therapy responses. This study examines the efficacy of various treatments in reducing CGCG recurrence. A literature review explored outcomes of surgical excision, curettage, intralesional corticosteroid injection, and adjuvant therapy, considering factors like lesion location, size, and histological features. Aggressive surgical techniques such as en bloc resection were found to potentially lower recurrence rates compared to conservative approaches. However, treatment should be tailored to individual patient needs. Further research is needed to confirm these findings and improve treatment strategies. A concise literature review was conducted using PubMed, MEDLINE, and Google Scholar, focusing on papers published from 1986 to 2024. Search terms included "central giant cell granuloma," "recurrence," "treatment modalities," and "surgical excision". Studies reporting recurrence rates and treatment outcomes for CGCG were analyzed. Twenty-nine studies were reviewed, including six studies on surgical excision and curettage, eight studies on intralesional corticosteroid injections, six studies on calcitonin therapy, five studies on interferon alpha therapy and four studies on the therapy with denosumab. Analysis indicated that aggressive surgical treatments like en bloc resection were associated with lower recurrence rates compared to conservative methods. Predictors of recurrence included lesion size (&gt;3 cm), location (mandible), and aggressive histopathological features. Aggressive surgical excision combined with nonsurgical methods may lower recurrence rates, while conservative techniques remain viable in some cases. Further prospective research is needed to validate these findings and enhance CGCG treatment options.

The visualization of hyperspectral images in display devices, having RGB colour composition channels is quite difficult due to the high dimensionality of these images. Thus, principal component analysis has been used as a dimensionality reduction algorithm to reduce information loss, by creating uncorrelated features. To classify regions in the hyperspectral images, K-means clustering has been used to form clusters/regions. These two algorithms have been implemented on the three datasets imaged by AVIRIS and ROSIS sensors.

Recent state-of-the-art scene text recognition methods have primarily focused on horizontal text in images. However, in several Asian countries, including China, large amounts of text in signs, books, and TV commercials are vertically directed. Because the horizontal and vertical texts exhibit different characteristics, developing an algorithm that can simultaneously recognize both types of text in real environments is necessary. To address this problem, we adopted the direction encoding mask (DEM) and selective attention network (SAN) methods based on supervised learning. DEM contains directional information to compensate in cases that lack text direction; therefore, our network is trained using this information to handle the vertical text. The SAN method is designed to work individually for both types of text. To train the network to recognize both types of text and to evaluate the effectiveness of the designed model, we prepared a new synthetic vertical text dataset and collected an actual vertical text dataset (VTD142) from the Web. Using these datasets, we proved that our proposed model can accurately recognize both vertical and horizontal text and can achieve state-of-the-art results in experiments using benchmark datasets, including the street view test (SVT), IIIT-5k, and ICDAR. Although our model is relatively simple as compared to its predecessors, it maintains the accuracy and is trained in an end-to-end manner.

Oil and gas pipeline vandalism is a recurrent problem in oil rich zones of Nigeria and its West African neighbors and remains a challenge for multinationals to set ahead control measures to avert possible damages to operations both in infrastructure and business profit margins. In this paper, an integrative systems model comprising of a machine intelligence technique called Hierarchical Temporal Memory (HTM) and a sequence learning neural network called the Online-Sequential Extreme Learning Machine (OS-ELM) is proposed for monitoring and prediction of pipeline pressure data. The system models the continual prediction of pipeline oil/gas pressure signals useful for secure monitoring and control to avert acts of vandalism in oil and gas installations. The HTM uses a spatial pooler operated in temporal aggregated fashion and is defined as HTM-SP. The OS-ELM technique uses an explicit hierarchical training scheme so that the best cost estimates may be found after a stipulated number of trial runs. We study the performance of three OS-ELM neural activations: the sigmoid (sig), sinusoidal (sin) and radial basis function (rbf) activations. The results indicate improvement factors of 1.297, 1.297 and 1.300 of the HTM-SP over the OS-ELM sigmoid, sinusoidal and radial basis activations respectively.

Transposable elements (TEs) are mobile genetic elements capable of rapidly altering the genome through their movements. The importance of TE activity has been documented in many biological processes, such as introducing genetic instability, altering patterns of gene expression, and accelerating genome evolution. Increasing appreciation of TEs results in the growing number of bioinformatics software to identify insertion events. However, the application of existing TE finding tools is limited by either narrow-focused design of the package, too many dependencies on other tools, or prior knowledge required as input files that may not be readily available to all users. Here, we report a simple pipeline, TEfinder, developed for the detection of new TE insertions with minimal software dependencies using four inputs that can be easily generated with popular variant calling pipelines. The external software requirements are BEDTools, SAMtools, and Picard. Necessary inputs include TEs present in the reference genome, binary paired-end alignment, reference genome index, and a list of TE names. We tested TEfinder pipeline among several evolving populations of Fusarium oxysporum generated through a short-term adaptation study. Our results demonstrate that this easy-to-use tool can effectively detect new TE insertion events, making it accessible and practical for TE analysis.

This article presents an automated vision-based algorithm for the die-scale inspection of wafer images captured using scanning acoustic tomography (SAT). This algorithm can find defective and abnormal die-scale patterns, and produce a wafer map to visualize the distribution of defects and anomalies on the wafer. The main procedures include standard template extraction, die detection through template matching, pattern candidate prediction through clustering, and pattern classification through deep learning. To conduct the template matching, we first introduce a two-step method to obtain a standard template from the original SAT image. Subsequently, a majority of the die patterns are detected through template matching. Thereafter, the columns and rows arranged from the detected dies are predicted using a clustering method; thus, an initial wafer map is produced. This map is composed of detected die patterns and predicted pattern candidates. In the final phase of the proposed algorithm, we implement a deep learning-based model to determine defective and abnormal patterns in the wafer map. The experimental results verified the effectiveness and efficiency of our proposed algorithm. In conclusion, the proposed method performs well in identifying defective and abnormal die patterns, and produces a wafer map that presents important information for solving wafer fabrication issues.

This paper highlights the importance of one-shot learning from prototype SKU images for efficient product recognition in retail and inventory management. Traditional methods require large supervised datasets to train deep neural networks, which can be costly and impractical. One-shot learning techniques mitigate this issue by enabling classification from a single prototype image per product class, thus reducing data annotation efforts. We introduce the variational prototyping-encoder (VPE), a novel deep neural network for one-shot classification. Utilizing a support set of prototype SKU images, VPE learns to classify query images by capturing image similarity and prototypical concepts. Unlike metric learning-based approaches, VPE pre-learns image translation from real-world object images to prototype images as a meta-task, facilitating efficient one-shot classification with minimal supervision. Our research demonstrates that VPE can significantly reduce the need for large datasets while accurately classifying query images into their respective categories, providing a practical solution for product classification tasks.

Nowadays, semantic segmentation is increasingly used in exploration by underwater robots, for example in autonomous navigation, so that the robot can recognise the nature and elements of its environment during the mission and act according to this classification to avoid collisions. Other applications can be found in the search for archaeological artefacts, in the inspection of underwater structures or in species monitoring. Therefore, it is necessary to try to improve the performance in these tasks as much as possible. To this end, we compare some methods for improving image quality and for data augmentation and test whether higher performance metrics can be achieved with both strategies. The experiments are performed with the SegNet implementations and the SUIM dataset with 8 common underwater classes to compare the obtained results with the already known ones. The results obtained with both strategies show that they are beneficial and lead to better performance results by achieving a mean IoU of 56% and an increased overall accuracy of 81.8%. The single result shows that there are 5 classes with an IoU value above 60% and only one class with an IoU value below 30%, which is a more reliable result and easier to use in real contexts.