Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

We propose a spectral filter based on Plastic Optical Fiber with micro-holes as a low-cost, robust, and highly reproducible spectral filter. The spectral filter is explored for two configurations: fiber extended in a straight line, and a fiber optic loop mirror scheme configuration. The transmission traces indicate a spectral blue shift of peak transmission, at 587 nm, 567 nm, 556 nm, and 536 nm for 0, 1, 2, and 3 holes in the fiber, respectively. The filter exhibits a bandpass period of approximately 120 nm. Additionally, we conducted a comparison of the transmission with holes separated by distances of 1 cm and 500 μm. The results demonstrate that the distance between holes does not alter the spectral transmission of the filter. In the case of the fiber loop mirror configuration, we observed that the bandpass can be adjusted, suggesting the presence of multimode interference. Exploring variations in the refractive index within the holes by filling them with glucose solutions at various concentrations, we determined that the filtering band and spectral shape remains unaltered, ensuring a stable and robust operation of our spectral filter.

Plastic contamination of small dimensions (

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

The aim of this research work is to get a method for Galfenol electrodeposition thought which we can control the desired percentage of Ga versus Fe that has the maximum magnetostriction constant. Galfenol is electrodeposited on an optical fiber with an imbedded Fiber Bragg Grating (FBG) in its core. The final objective, that goes further of the scope of this research, is to get an optical magnetostrictive sensor. The device will sense magnetic field or current based on the combination of this magnetostrictive Galfenol, that will stress the optical fiber with the application of magnetic field or current and will change the reflected wavelength of the FBG as a consequence of the variation of the Bragg wavelength. We have developed a method of electrodeposition that allows controlling the density of current in the electrodeposition process in order to get the desired percentage of Ga and Fe in the alloy Ga X Fe 1-x. We have manufactured a set of samples with different parameters (as density of current and pH) and we have characterized these samples morphological, structural and magnetically. With this research we want to give to the scientific community the groundwork to design magnetostrictive optical sensors based on and FBG coated by giant magnetostrictive material. In this paper we have developed a method of covering the optical fiber controlling the composition of (Ga X Fe 1-X) in order to be able to get the maximum magnetostriction constant.

Optical fiber sensors based on tapered optical fiber (TOF) structure have attracted a considerable amount of attention from researchers due to the advantages of simple fabrication, high stability, diverse structures, and have great potential for applications in many fields such as physics, chemistry and biology. Compared with ordinary optical fibers, TOF with their unique structural characteristics significantly improve the sensitivity and response speed of fiber-optic sensors and broaden the application range. This review presents an overview of the latest research status and characteristics of fiber-optic sensors and TOF sensors. Then the working principle of TOF sensors, fabrication schemes of TOF structures, novel TOF structures in recent years, and the growing emerging application areas are described. Finally, the development trends and challenges of TOF sensors are prospected. The objective of this review is to convey novel perspectives and strategies for the performance optimization and design of TOF sensors based on fiber-optic sensing technologies.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

Flexible wearable pressure sensors offer numerous benefits, including superior sensing capabilities, a lightweight and compact design, and exceptional conformal properties, making them highly sought after in various applications including medical monitoring, human-computer interaction, and electronic skin. Because of their excellent characteristics, such as simple fabrication, low power consumption, and short response time, capacitive pressure sensors have received widespread attention. As a flexible polymer material, polydimethylsiloxane (PDMS) is widely used in the preparation of dielectric layers for capacitive pressure sensors. The Young's modulus of the flexible polymer can be effectively decreased through the synergistic application of sacrificial template and laser ablation techniques, thereby improving the functionality of capacitive pressure sensors. In this study, a novel sensor was developed through a series of processes including sacrificial template method using NaCl microparticles, CO₂ laser ablation, and sandwiching a porous PDMS dielectric layer between two flexible electrodes to create a capacitive pressure sensor. The sensor demonstrates a sensitivity of 0.694 kPa-1 within the pressure range of 0-1 kPa, and can effectively detect pressures ranging from 3 Pa to 200 kPa. The sensor demonstrates stability for up to 500 cycles, with a rapid response time of 96ms and a recovery time of 118ms, coupled with a low hysteresis of 6.8%. Furthermore, our testing indicates that the sensor possesses limitless potential for use in detecting human physiological activities and signaling emergencies.

Conventional methods for pathogen detection in water rely on time-consuming enrichment steps followed by biochemical identification strategies, which require assay times ranging from 24 hours to up to a week. However, in recent years, significant efforts have been made towards the development of biosensing technologies enabling rapid and close-to-real-time detection of waterborne pathogens. In previous studies, we developed a plastic optical fiber (POF) immunosensor using an optoelectronic configuration consisting of a U-Shape probe connected to an LED and a photodetector. Bacterial detection was evaluated with the immunosensor immersed in a bacterial suspension in water with a known concentration. Here, we report on the sensitivity of a new optoelectronic configuration consisting of two POF U-Shape probes, one as the reference and the other as the immunosensor, for the detection of Escherichia coli. In addition, another way of detection was tested where the sensors were calibrated in the air, before immersed in bacterial suspension and then read in the air, making the immunosensor more sensitive and with a faster detection time. This new sensor detected the presence of E. coli at 104 CFU/mL in less than 10 minutes. Currently sub 10 minutes is faster than previous studies using fiber-optic based biosensors. It is also a much simpler and quicker methodology when compared with conventional laboratory technology.

Due to the renewed variation in government and political systems inside and outside countries, and with the high tariffs at borders, the latter have become an outlet for terrorism and smugglers. Therefore, each country seeks to develop its own protection system, and the technologies used in these systems vary according to the severity and the importance of the installations to be protected, it is found that some of them are expensive and unnecessary, but other have good and variable levels of efficiency. Consequently, the idea of designing a surveillance system that can monitor and control access becomes indispensable. In the same context, this work is of crucial strategic and geopolitical importance. It combines pre-existing alarm and monitoring methods and revolutionary Internet of Things (IoT) application products, of which Wireless Sensor Networks (WSN) and Optical Fiber Sensors (OFS) are part of this application. This article presents the distribution of wireless radar nodes accompanying with a Bragg fiber sensor to identify each rolling intruder incoming the zone to be monitored, from the determination of its speed, weight and wheelbase distance.

In the realm of power delivery to end-users, transformers are indispensable, with their malfunctions leading to substantial economic, safety, and environmental repercussions. The need for persistent surveillance is accentuated for in-situ oil-filled transformers, given the potential degradation of oil and the emergence of related ageing by-products. As the focus tilts towards online detection methodologies for transformer oil ageing, bypassing challenges associated with traditional offline methods such as sample contamination and misinterpretation, fiber optic sensors are gaining trac-tion due to their compact nature, cost-effectiveness, and resilience to electromagnetic disturbances typical in high-voltage environments. This work delves into the sensitivity analysis of intensi-ty-modulated plastic optical fiber sensors. The investigation encompasses key determinants such as the influence of optical source wavelengths, noise response dynamics, ramifications of varying sensing lengths, and repeatability assessments. Findings underscore that elongating the sensing length detrimentally affects both the linearity response and repeatability, largely attributed to the diminished resistance to external noise. Additionally, the choice of the optical source wavelength proved to be a critical variable in assessing sensor sensitivity.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Umbilical cord-derived mesenchymal stem cells (UC-MSCs) are reported to have features intermediate between fetal and adult mesenchymal cells. Hence, UC-MSCs were cocultured with chondrocytes and Schwann cells to induce differentiation because of their flexible differentiation potential. US-MSCs were obtained from umbilical cords and cells at second passage were used in the experiments. Atelocollagen sponge was used as the scaffold for coculture; a horizontal, interactive coculture plate with a 0.6-μm pore size filter was placed between the connected vessels. US-MSCs were cocultured separately with chondrocytes and Schwann cells and culture alone served as a control. Five weeks after induction of differentiation, each specimen was evaluated histologically. In specimens cocultured with chondrocytes and the controls, cartilage tissues were detected using hematoxylin-eosin and toluidine blue staining. Cells positive for S100 protein were detected in the specimens cocultured with Schwann cells, but not in the controls. UC-MSCs were easily induced to differentiate into chondrocytes and neural cells by coculture. This indicates that continuously-shared humoral factors were effective in inducing differentiation of UC-MSCs. Coculture appears to be a potential technique for tissue regeneration using MSCs.

Addressing real-time aircraft target detection in microsatellite-based visible light remote sensing video imaging requires considering the limitations of imaging payload resolution, complex ground backgrounds, and the relative positional changes between the platform and aircraft. These factors lead to multi-scale variations in aircraft targets, making high-precision real-time detection of small targets in complex backgrounds a significant challenge for the detection algorithms. Hence, this paper introduces a real-time aircraft target detection algorithm for remote sensing imaging using an improved lightweight attention mechanism that relies on the YOLOv7 framework (SE-CBAM-YOLOv7). The proposed algorithm replaces the standard convolution (Conv) with a lightweight convolutional SEConv to reduce the computational parameters and accelerate the detection process of small aircraft targets, thus enhancing real-time onboard processing capabilities. Besides, the SEConv-based SPPCSPC (Spatial Pyramid Pooling and Connected Spatial Pyramid Convolution) module extracts image features. It improves detection accuracy while the feature fusion section integrates the CBAM hybrid attention network, forming the CBAMCAT module. Furthermore, it optimizes small aircraft target features in channel and spatial dimensions, improving the model's feature fusion capabilities. Experiments on public remote sensing datasets reveal the proposed SE-CBAM-YOLOv7 improves detection accuracy by 3% and mAP value by 4.2% compared to YOLOv7, significantly enhancing the detection capability for small-sized aircraft targets in satellite remote sensing imaging.

Human-robot collaboration is a new trend in modern manufacture. The safety or human protection is of great significance due to the share of the same workshop between humans and robots. To achieve effective protection, in this paper, a contact force sensor based on the 8-shaped wound polymer optical fiber is proposed. The 8-shaped wound structure can convert the normal contact force to the shrinkage of the 8-shaped optical fiber ring. The macro-bending loss of the optical fiber is used to detect the contact force. Compared with conventional sensors, the proposed scheme has the advantage of high flexibility, low cost, fast response, high repeatability, which shows the great promise on actively alarming collision and passively reducing the hurt.

Evans' Syndrome (ES) is a rare autoimmune disorder characterized by the simultaneous occurrence of immune thrombocytopenia (ITP) and autoimmune hemolytic anemia (AIHA). Thrombotic complications in ES patients are uncommon, particularly involving Buerger's Disease (BD). We report a case of a 49-year-old male with ES and a history of diabetes and heavy smoking, presenting with a necrotic wound on his right great toe. Diagnostic evaluations revealed severe stenosis and thrombosis in the lower limb arteries, diagnosed as BD. The patient underwent successful popliteal-tibioperoneal artery bypass surgery and subsequent disarticulation and revision of the distal phalanx, followed by the application of an acellular dermal matrix (ADM) to promote healing. Post-surgery, the patient showed significant improvement in blood flow and complete epithelialization without complications. This case highlights the importance of a multidisciplinary approach in managing complex wounds in ES patients, suggesting potential treatment pathways for future cases involving BD

To address the issue of reduced orbit estimation accuracy resulting from discrepancies between in-orbit measured geomagnetic field values and IGRF model values in autonomous orbit estimation of microsatellites based on geomagnetic field measurements, this study introduces an adaptive cubature H-infinity filtering algorithm. Firstly, it presents the low-altitude orbital dynamics model and geomagnetic field measurement model for microsatellites. Subsequently, within the adaptive cubature H-infinity filtering algorithm, a spherical simplex rule and a second-order Gaussian-Legendre quadrature criterion are employed to compute the spherical surface integral and radial integral. Additionally, a spherical simplex-radial quadrature rule is proposed to enhance the approximation accuracy of nonlinear Gaussian weighted integrals. Furthermore, by integrating extended H-infinity filtering based on game theory with the cubature quadrature rule, an inverse proportional relationship between constraint level and filtering innovation is established. This allows for adaptive adjustment of the constraint level to enhance robustness against model errors. Finally, through semi-physical simulation experiments, it is demonstrated that compared with traditional algorithms, the proposed algorithm improves autonomous orbit estimation position accuracy of microsatellites by 7.49%, while also enhancing velocity accuracy by 3.1%, thus validating its effectiveness.

Background. Cervical esophageal reconstruction is vital for improving the quality of life in cancer surgery patients. Microsurgery is crucial, providing vascularized tissue for defect repair, particularly in secondary cases with a higher risk of failure due to larger defects and damage from previous surgery and radiotherapy. The purpose of this study was to describe the clinical characteristics of a series of patients who underwent secondary repair of esophageal defects and provide practical information for the management and treatment of such cases based on the authors' experience and the literature review. Methods. We retrospectively reviewed the electronic medical records of the Plastic Surgery Clinic at the University of Trieste to identify cases of patients who underwent secondary esophageal microsurgical reconstructions following oncological surgery. Patient demographics, etiology of esophageal defects, previous surgical history, and preoperative assessments were collected from medical records. Surgical techniques employed for reconstruction, such as pedicled flaps or free tissue transfers, were documented along with intraoperative details. Postoperative outcomes, including complications, graft viability, and functional outcomes, were evaluated during follow-up. Results. We treated 13 cases of secondary esophageal reconstructions from 2011 to 2022. Most commonly, Antero-Lateral Thigh (ALT) flaps were used in 10 cases, while 2 cases employed Radial Forearm Flap (RFF), and 1 a chimeric parascapular flap. No flap failures occurred during a median 50-month follow-up. One ALT flap patient experienced post-op stricture but maintained swallowing ability. A single tracheoesophageal fistula occurred in a RFF patient with a history of radiotherapy and completion lymph node dissection. Conclusions. Cervical esophageal reconstruction significantly impacts patients' quality of life by restoring oral feeding and phonation. When local flaps fall short, microsurgical reconstruction with intestinal flaps is valuable, but burdened by limitations. For challenging secondary cases, ALT or RFF flaps emerge as safer options due to their robust pedicles, yielding low complication rates and positive functional outcomes.

DIEP-based breast reconstruction necessitates wide undermining at the abdominal donor-site, creating large wound areas. Flap harvesting is usually conducted using electrosurgical dissection devices. This study sought to compare the clinical outcomes in patients after using the PEAK PlasmaBlade (PPB) versus monopolar electrocautery (MPE). This retrospective cohort study included 128 patients with DIEP-based breast reconstruction. Patient characteristics as well as information on the postoperative course were collected and a comparative evaluation was conducted. The MPE group exhibited significantly (p* = 0.0324) higher abdominal drainage volume (351.11 ± 185.96 ml) compared to the PPB group (279.38 ± 183.38 ml). Subgroup analysis demonstrated that PPB significantly reduced postoperative wound fluid in patients with BMI > 30 kg/m² (p* = 0.0284), without prior neoadjuvant chemotherapy (p** = 0.0041), and among non-smokers (p = 0.0046). Furthermore, postoperative pain was significantly (p**** < 0.0001) lower in the PPB cohort. This study confirms the non-inferiority of the PEAK PlasmaBlade to conventional electrocautery for abdominal flap harvesting. The PPB demonstrated advantages, notably reduced drainage volume and lower postoperative pain levels. Recognizing patient subsets that benefit more from the PPB highlights the importance of personalized device selection based on patient characteristics.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

Calcium sulphate (CS) is currently used as a bioabsorbable, completely synthetic and sterile material in the management of infected tissues and dead spaces (DS) mainly resulting from surgical procedures. Residual DS in the postoperative, may create an environment where hematomas fill up and bacteria can proliferate, leading to a high incidence of postoperative infections. Considering the available reviews in the literature, CS has been mainly studied in orthopedic surgery mostly giving brilliant results and low complication rates. Nowadays, orthopedists avail it in the form of pearls both as a bone void filler and as an “off-label” delivery agent for antibiotics in arthroplasty, chronic osteomyelitis and open fractures, paving the way of its application in many other contexts given its natural dis-position to biodegradation. In the last years, CS beads have been gaining ground in the general, vascular and endocrinological surgical specialties. Despite its clear potential and the increasing number of scientific evidences on the safety and effectiveness of CS application in the prophylaxis and treatment of infections, there are not many studies reporting on its application in fields other than orthopedics, with a substantial paucity in plastic and reconstructive surgery literature. This is some-how surprising, since reconstructive surgery often deals with complex wounds secondary to bone and soft tissue exposure, suture dehiscence, trauma, and surgical site infections. As far as we know this is the first updated systematic review assessing the state of the art, indications and new perspectives on the application of CS beads in plastic and reconstructive surgery.

The high prevalence of human papillomavirus (HPV) infection in oropharyngeal squamous cell carcinoma (OPSCC) is well-established, with p16 expression being a strong predictor. HPV-related tumors exhibit unique mechanisms targeting p16 and p53 proteins. However, re-search on HPV prevalence and the combined predictive value of p16 and p53 expression in head and neck cutaneous squamous cell carcinomas (HNCSCC), especially in Asian populations, is limited. This retrospective study surveyed 62 HNCSCC patients (2011–2020), excluding those with facial warts or other skin cancers. All patients underwent wide excision and biopsy. Immuno-histochemical staining for HPV, p16, and p53 yielded both positive and negative results. The relevance of each marker was investigated by categorizing the tumor locations into high-risk (Area H) and mid-risk (Area M) zones based on recurrence frequency. Of the 62 patients, 20 (32.26%) were male, with an average age of 82.27 years (26–103). Area H included 19 cases (30.65%), with the eyelid and lip being the most common sites (five cases, 8.06%). Area M in-cluded 43 cases (69.35%), with the cheek being the most common site (29 cases, 46.77%). p16 ex-pression was positive in 24 patients (38.71%), p53 expression in 42 patients (72.58%), and HPV in five patients (8.06%). No significant association was found between p16 expression and HPV presence (p > 0.99), with a positive predictive value of 8.33%. This indicates that p16, a surrogate marker of HPV in OPSCC, is not a reliable marker for HPV in HNCSCC. This study enhances our understanding of the relationship between HPV, p53, and p16 in HNCSCC in Asian populations and offers valuable insights for further research.

Background: This study aimed to investigate the impact of the COVID-19 pandemic on breast reconstruction trends in the United States, focusing on implant-based and autologous techniques, as well as the timing of reconstruction (immediate vs. delayed). Methods: A retrospective analysis of data from the American Society of Plastic Surgeons' National Plastic Surgery Statistics from 2015 to 2022 was conducted. Annual trends in breast reconstruction procedures were analyzed, comparing the pre-pandemic (2015-2019) and pandemic (2020-2022) periods. Results: The total number of breast reconstructions increased from 106,338 in 2015 to 151,641 in 2022. The proportion of implant-based reconstructions decreased from 81.41% pre-pandemic to 76.51% during the pandemic (p < 0.001), with a notable rise in direct-to-implant procedures from 10.37% to 19.12% (p < 0.001). Autologous reconstructions increased from 18.59% to 23.49% (p < 0.001). Among autologous techniques, DIEP flaps remained the most popular. Immediate reconstruction rates increased from 72.61% pre-pandemic to 75.57% during the pandemic, while delayed recon-struction rates decreased from 27.39% to 24.43% (p < 0.001). Conclusions: The COVID-19 pandemic has significantly influenced breast reconstruction trends in the United States, with a shift towards autologous techniques, particularly DIEP flaps, and an in-crease in immediate reconstructions. These changes may reflect adaptations in surgical practice and decision-making processes in response to the unique challenges posed by the pandemic. Further research is needed to assess the long-term outcomes and patient satisfaction associated with these trends.

The review aims to assess fifteen (15) academic literature sources, highlighting the application of machine learning algorithms in the maintenance operations of optical fiber networks. It exhibits the collection of data using PRISMA methodology—Preferred Reporting Item for Systems Review and Meta-Analyses. The application, results, and performance metrics are discussed based on the collected observations, computations, and statistics in the studies, which revealed records of high accuracy degrees ranging from 86% to 98% on average and quality ML models including Neural Networks (NNs), Support Vector Machines (SVMs), and LSTM, as well as deep learning models that disclosed effective results of determining challenges and problems within the optical fiber lines. The review mainly centralized on superior machine learning technologies that surpass traditional techniques in fault detection and localization for improved optical fiber networks’ operations while providing insights into the limitations and challenges encountered in real-world applications of these models, offering a comprehensive perspective on the optical fiber network’s domain.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

Cutaneous squamous cell carcinoma is a prevalent malignancy with a rising incidence and notably high mutational load. Exploring the genetic nuances of cSCC and investigating molecular approaches stands as a potential avenue for improving outcome in high-risk patients. This retrospective case-control study involved two cohorts of 14 patients (“discovery cohort”) and 12 patients (“validation cohort”) with cSCC located in head-neck anatomical district and diagnosed at pT2 stage. Overall, cases developed early local relapse of the disease whereas controls never re-lapsed during the entire follow-up period. Next generation sequencing (NGS) approach conducted on histological samples revealed that TP53 and CDKN2A were the most frequently mutated genes in our series. No specific mutation was identified as potential prognostic or therapeutic targets. Controls exhibited a tendency toward a higher mutational rate compared to cases. It is possible that an increased number of mutations could prompt the cSCC to expose more antigens, becoming more immunogenic and facilitating the recognition by the immune system. This could enhance and sustain immunological response, potentially preventing future recurrences.

Aiming at solving difficulties related to aero-engine classification and identification, the infrared spectra of aero-engine hot jets are measured by telemetry Fourier transform infrared spectrometer, and a six types aero-engine hot jet spectrum data set is generated. The spectrum data set were randomly sampled at a ratio of 8:1:1 to generate training set, validation set and prediction set. In this paper, a Peak Finding Siamese Convolutional Neural Network (PF-SCNN) is designed to match and classify spectrum data. In the first place, the matching pairs of training set and validation set are made independently with the labels of positive and negative samples creating. The spectrum feature extraction and distance similarity calculation are carried out by the Siamese convolutional neural network (SCNN). When entering the prediction phase, the prediction set and training set are integrated to predict in the trained model. The prediction set labels are ultimately determined by matching them with the training set labels having the highest similarities to ensure accurate predictions. To improve the operation efficiency of the SCNN, a peak finding method is introduced to extract the spectrum peaks. Peak positions of high frequency are counted, while the peak data are extracted. The peak data are used to take the place of the original data for training and prediction. The performance measures are defined as Accuracy, Precision, Recall, Confusion matrix and F1-score, and the prediction accuracy was up to 99%. The experimental results indicate that the proposed PF-SCNN is suitable for our spectral dataset and can complete the task of infrared spectrum classification of aero-engine hot jets.

Focusing on the problem of identifying and classifying aero-engine models, this paper measures the infrared spectrum data of aero-engine hot jets using a telemetry Fourier transform infrared spectrometer. Simultaneously, infrared spectral data sets with the six different types of aero-engines are created. For the purpose of classifying and identifying infrared spectral data, a CNN architecture based on the continuous wavelet transform peak seeking attention mechanism (CWT-AM-CNN) is suggested. This method calculates the peak value of middle wave band by continuous wavelet transform, and the peak data is extracted by the statistics of the wave number locations with high frequency. Attention mechanism is used for the peak data, and the attention mechanism is weighted to the feature map of the feature extraction block. The training set, vali-dation set and prediction set are divided in the ratio of 8:1:1 for the infrared spectral data sets. For three different data sets, CWT-AM-CNN proposed in this paper is compared with the classical classifier algorithm based on CO2 feature vector and the popular AE, RNN and LSTM spectral processing networks. The prediction accuracy of the proposed algorithm in the three data sets is as high as 97%, and the lightweight network structure design not only guarantees high precision, but also has a fast running speed, which can realize the rapid and high-precision classification of the infrared spectral data of the aero-engine hot jets.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

The distributed long-range sensing system using the standard telecommunication single-mode optical fiber in a function of a distributed sensor for sensing of mechanical vibrations is described. Various events generating vibrations such as walking or running person, moving cars, trains and others can be detected, localized and classified. The sensor and related sensing system components were designed and constructed and the system was tested both in the laboratory and in the real situation with 88 km telecom optical link, and the results are presented.

Monte Carlo techniques have been extensively used for planning laser-based clinical procedures such as photobiomodulation. However, the effect of several biological tissue characteristics, including morphological structure and physiological parameters, has not been carefully addressed in many applications. Specifically, many questions remain concerning the effect of skin phototype and body mass index on the efficacy of photobiomodulation for extraoral therapies. To address these questions, a Monte Carlo simulation model was developed to analyze the effects of body mass index-dependent skin structure and Fitzpatrick skin type, specifically tailored for the morphological characteristics of cheek tissue. The model describes the settings of a typical oral photobiomodulation treatment protocol for pain relief, namely the use of 660 nm and 808 nm laser wavelengths and a therapeutic dose of 2.0 J/cm² on the masseter muscle. The simulations were used to train a machine learning predictive model aimed at accelerating the treatment planning stage and assessing the importance of patient-specific parameters. A multiple regression approach was adopted to predict muscle dose and treatment time for the effective delivered dose.

Objectives: Describe the epidemiology of burns in the pediatric population. Analyze and compare the results obtained from the treatment of burn wounds by using the bio-preserved human epidermis allograft (BHEA) and other types of dressings and determine the need for further need of a skin graft. Methods: A retrospective cross-sectional study of pediatric population with burn injuries was conducted, grouped into categories based on their age group, and the mechanisms of injury into 6 categories: scald, flame, contact, electrical, chemical and friction. Describing the extension and depth of the burn injury. The results of treatment of two groups; the patients who used (BHEA) and the group with “other dressings” were analyzed by inferential statistics to establish the relationship between the use of BHEA and the need for skin grafts compared to the other group. Results: A total of 65 patients were obtained. The average age was 4.5 years (±3.8). Preschoolers (1-5 years old) were the most frequent age group 64% (n=42). Male patients represented 61% (n=40) of cases. Scald was the most reported mechanism 64% (n=42). The average total body surface area burned (TBSAB) was 10.8% (± 9.2). Mixed partial thickness burn (superficial and deep) was the most common with a 55%. The head was the most affected anatomical site; 30%. The face was the most reported “special anatomical site” with a 40% (n=30). 32.2 % of the population (n=21) was treated with BHEA. The average time of epithelialization of the BHEA group was 8 days (±7.2), and their average hospital stay time was 7 days (±5.7). In the “other dressing” group, the average epithelialization time was 18 days (±13.6), and the average hospital stay time was 11 days (±12.6). Fifty percent (n=22) of the “other dressing” group required skin grafts. In the BHEA group only 19% (n=4) required skin grafts. An OR of 0.23 and CI of 95% (0.06 – 0.81) with a p value of (0.017) for the need of skin grafts after de use of BHEA was obtained. Conclusion: The epidemiological results reported are similar to those described in the literature. The use of (BHEA) proved to be a good option for the management of partial thickness burns and burns in transition, promoting timely epithelilization and avoiding deepening of the burns while reducing morbidity, hospital stay and care costs.

A new-type vibration sensor based on a fiber Bragg grating combining with a special structure-packaged design is proposed for monitoring the mechanical vibration signals. Three different sensing structures including the film squeeze type, new film squeeze type and elastic tape squeeze type are proposed for measuring the vibration signals with the frequency range from tens to thousands of Hz. In the comparison of experimental results, the new film squeeze structure has a nice sensing performance in the range from 100 to 1000 Hz with the sensitivity of 35 mV/V. For the elastic tape squeeze structure, the elastic tape is designed to encapsulate the optical fiber with a good frequency response from 1100 to 3100 Hz. In addition, by using the new film squeeze structure to measure the steady-state and non-steady-state vibration signals, the spectral components of sensing signals are analyzed by using the wavelet transformation for confirming the testing signals. These vibration fiber sensors can be applied in the measurement of high-end manufacture-facility vibration or earthquake vibrations etc.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Neurofibromas, rare benign tumors of the peripheral nerve sheath, present diagnostic challenges, particularly in diabetic patients with toe ulcers. This case involves a 55-year-old female with type 2 diabetes mellitus who developed an enlarging ulcer on her right second toe. The initial evaluation suggested a diabetic ulcer; however, advanced imaging revealed a mass-like lesion. Partial excision and biopsy confirmed a neurofibroma with spindle cells within the myxoid stroma and S100 protein expression. One month later, total excision and Z-plasty reconstruction were performed under general anesthesia. The patient’s postoperative recovery was uneventful, and the patient was discharged without complications. Follow-up revealed successful healing with no recurrence or functional issues. This case highlights the importance of considering neurofibromas in the differential diagnosis of diabetic toe ulcers to avoid misdiagnosis and ensure appropriate management.

Treatment techniques for facial paralysis have evolved significantly over the past few decades, offering a variety of options to improve facial symmetry and muscle function. The purpose of this paper is to introduce a novel static treatment technique for the surface of the nasolabial fold (NLF) in patients with chronic facial nerve paralysis, aged between 40 and 80 years, who are not candidates for dynamic rehabilitation and present with NLF erasure. The surgical marking process was initiated by determining the projection of the nasolabial fold on the paralyzed side, through measurement of the NLF on the non-paralyzed side. Subsequently, a line was drawn around the nasal ala, and a second line was demarcated in the medial region of the sulcus. In the region close to the nasal ala, along this second line, a notch was planned. The procedure was conducted under local anesthesia. In this study, four procedures were performed without any complications. Comparatively, the outcomes demonstrated an improvement in facial symmetry, the creation of a new NLF, elevation of the ipsilateral lip commissure, and correction of nasal deviation. The proposed technique is straightforward, reproducible, and can be performed in an outpatient setting.

Thin people who undergo implant insertion into the chest wall face a high risk of implant exposure to the external environment. Five months after an 8-year-old boy underwent implantable cardioverter-defibrillator (ICD) implantation in a subcutaneous pocket in the left anterolateral chest wall to manage long QT syndrome, ICD replacement became necessary owing to exposure risk from distal and lateral thinning of the ICD pocket. Pocket rupture and exposure would increase the risk of infection; therefore, we performed ICD removal and primary pocket closure. Two weeks later, a new suprafascial pocket was created, acellular dermal matrix (ADM) was attached to the inner wall to prevent ICD protrusion, and a new ICD was inserted. One year postoperatively, the ADM was engrafted, and no complications were observed. A thin subcutaneous layer increases the risk of ICD implantation complications. Inner wall strengthening with ADM can help prevent pocket rupture.

Road infrastructure is a key public asset because it benefits the social and economic development of any country. It plays an important role for the development of the industrial complex, the production sector and the road surfaces of transport roads should be of high quality, have a long service life. Road infrastructure, as well as all infrastructure, requires preservation, maintenance and repair. There are special requirements for the roadway that must be observed during construction or repair. This article is devoted to a detailed study of the use of fiber optics sensors (FOS) based on the fiber Bragg grating (FBG) for road surface monitoring. Such a fiber sensor consisting of a fiber Bragg grid and a pair of grids can offer the possibility of simultaneous measurement of deformation and temperature for monitoring the pavement. Temperature and deformation measurements were carried out by installing a sensor on the surface of a made asphalt sample. The built-in fiber sensor based on FBG provides important information about how the pavement structure can withstand the load, subsidence of soil, timely implement road safety and stability measures evaluate and predict the service life of the pavement. The results of the study showed that the synchronicity, repeatability and linearity of the characteristics of the fiber sensor are excellent. The difference between the experimental and theoretical results is about 7%. Thus, based on the results of the obtained data, the fiber sensor on the FBG can be used for monitoring, designing road surfaces and in general transport infrastructure.

Distributed fiber optic vibration sensors based on Φ-OTDR using Rayleigh backscattering of highly coherent light source pulses are very popular type in the area of sensors due to many attractive features, mainly due to its distributed manner of sensing, i.e. they can operate as thousands of local sensors simultaneously. The paper summarizes and describes several important modifications of the original sensor scheme to enhance its key performance parameters and to extend its application potential. A multi-fiber sensor form was proposed. Single- and two-fiber sensors were designed, constructed and tested both in the laboratory and in a real environment. Variants of two-fiber sensor utilizing optical switches for the sensor flexibility enhancement are proposed and their applications are described.

The aim of this paper is to create a sensor model based on optical crystal fibers (PCF). The aim of this model is to find and identify zinc cadmium. This thesis looked at three different categories of concentrations. For sensor architecture, PCF was generated using single-mode fiber-to-end split fusion (SM-PCF-SM). In this experiment, a specific wavelength spectrum was used to alter the concentration of materials covering the fiber in order to demonstrate the fiber's sensing capability. The 550nm wavelength has been used as the optical source for the fiber. The change in the output power of the external light was monitored and changes were observed for each concentration of the concentrations around the fiber. It has been found that the fiber is sensitive to small changes in concentrations. The absorption of the fiber has been calculated for the incoming capacity, as well as the losses in the capacity outside the fiber.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

In this study, Brillouin optical time-domain analysis (BOTDA) sensing technology was utilized for monitoring settlement in a similarity model of a highway subgrade. As contact winding cannot be used for an optical fiber that is buried directly in soil, uncoupling between. the fiber and the soil can occur. Thus, an optical-fiber-embedded beam (OFEB) was developed, and a method for measuring and calculating the beam deformation was proposed. A calibration test and a test on a similarity model of a subgrade were carried out to investigate the applicability and monitoring accuracy of the OFEB. It was concluded that the OFEB can accurately measure beam deflection, where the maximum relative error between measurements by the optical fiber and a displacement transducer was approximately 5%. The OFEB was embedded directly into a similarity model of a subgrade to monitor settlement. The deflection deformation of the OFEB was found to be close to the subgrade settlement over a certain settlement range with a relative error below 8.1%. Thus, the OFEB can be used to realize measure large-range distributed settlement in a subgrade. A numerical simulation was performed to identify appropriate beam dimensions and material design parameters, thereby extending the measurement range before decoupling of the OFEB and soil occurs. The enhancement of the measurement range and accuracy of the OFEB based on the preliminary experiments carried out in this study enables further investigation of settlement monitoring.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

Breast cancer in patients with prior breast augmentation poses unique challenges for detection, diagnosis, and management. Mastectomy rates are increasing, and patients with prior augmen-tation often have a lower body mass index, making autologous techniques unsuitable. This study aims to assess the best reconstructive option in patients with a history of subglandular or dual plane breast augmentation. Materials and methods: a prospective analysis was conducted on pa-tients who underwent breast reconstruction after mastectomy. Patients with subglandular or dual plane breast augmentation were included. Patients were divided into submuscular breast recon-struction (group 2) or prepectoral breast reconstruction (group 1) groups. Demographic and sur-gical data were collected. Results: A total of 47 patients were included, with 23 in Group 1 and 24 in the Group 2. Complications occurred in 11 patients (23.4%), with significant differences be-tween groups. The most common complication was seroma formation. Implant loss occurred in 4.3% of cases in the Group 1, while no implant loss was observed in the Group 2. Patient-reported satisfaction scores were similar between groups at 12 months postoperatively. Conclusions: sub-pectoral breast reconstruction with a tissue expander seems a safer and effective technique for pa-tients with prior breast augmentation. It resulted in fewer complications. This approach should be considered as an option for breast reconstruction after mastectomy in this cohort of patients.

This paper presents the results of experimental and numerical investigations aimed at enhancing the flexural capacity of Precast Concrete Corbel Beam-Column Connections (PC-CBCC) using Fiber-Reinforced Plastic (FRP) sheets. The experimental study primarily focused on assessing the flexural capacity of pinned PC-CBCCs reinforced with FRP layers, comparing them to a moment-resisting connection. A series of half-scale specimens, including three PC-CBCCs with varying FRP configurations, were tested alongside one in-situ concrete fixed connection. The objective was to quantify the ultimate flexural capacity of PC-CBCCs reinforced by FRP sheets. The effects of FRP layer thickness, locations, and potential debonding were examined under unidirectional static tests while applying a constant axial compressive load to the columns and subjecting the beams to lateral loads until fracture. Additionally, a precise finite element model of the PC-CBCCs and a fixed joint was developed and verified to simulate nonlinear static analyses of the connections in ANSYS software. A comprehensive comparison was conducted to determine their responses by employing various FRP configurations and properties. The tests and numerical results demonstrate that wrapping PC-CBCCs with anchored FRPs can transform pin connections into moment-resistant joints. Moreover, critical design parameters such as bond length, thickness, and placement of FRP sheets, along with appropriate mechanical anchorage, are identified to prevent debonding and delamination.

Burnout in healthcare affects the quality of patient care. In 2020, Mayo Clinic implemented Advanced Care at Home (ACH), a new hospital-at-home program. We aimed to assess burnout levels among ACH providers, analyzing data from quarterly surveys. Physicians and nurse practitioners registered in ACH completed a 16-question anonymous survey distributed via email. Ten questions from the original survey used the Maslach Burnout Inventory to measure the three domains associated with burnout: depersonalization, emotional exhaustion, and personal achievement. We conducted a descriptive analysis using frequency distribution and percentages. A total of 27 providers participated, with response rates of 38%, 23%, and 66% in the first, second, and third quarters. Over 75% of the participants responded satisfactorily to nine of the ten questions associated with the risk of burnout. Moreover, 77% of providers felt joyful at work "always or most of the time." Of the 74% of participants who responded to the question about feeling burned out from work, 48% of the participants "strongly” or “somewhat” disagreed, while only 26% "strongly” or “somewhat” agreed. Mayo Clinic's ACH has demonstrated low levels of burnout among providers, positively impacting the well-being of healthcare workers and contributing to a high standard of patient care.

Over the past decade, Deep Learning (DL) had been applied in a large number of optical sensors’ applications. DL algorithms can improve the accuracy and reduce the noise level in optical sensors. Optical sensors are considered as promise technology for the modern intelligent sensing platforms. These sensors are widely used to process monitoring, quality prediction, pollution, defense, security and many other applications. However, they suffer major challenges such as the large generated data and low processing speed for that data and moreover the much cost of these sensor. These challenges can be mitigated by integrating deep learning system with the optical sensor technologies. This paper presents recent studies that integrate DL algorithms with optical sensors applications. This paper also highlights several of DL algorithms directions that promise a considerable impact on use for optical sensor applications. Moreover, this study provides new directions for the future related research development.

This paper presents a new optical, multi-functional, high-resolution 3-axis sensor which serves to navigate and can, for example, replace standard joysticks in medical devices such as electric wheelchairs, surgical robots or medical diagnosis devices. A light source, e.g. a laser diode is affixed to a movable axis and projects a random geometric shape on an image sensor (CMOS or CCD). The software in the downstream microcontroller identifies the geometric shape’s center, distortion and size, then calculates X, Y, and Z coordinates. These coordinates can then be processed in attached devices. The 3-axis sensor is characterized by its very high resolution, precise reproducibility and plausibility of the coordinates produced. In addition, optical processing of the signal provides a high level of safety against electromagnetic and radio frequency interference. The sensor presented here is adaptive and can be adjusted to fit a user’s range of motion (stroke and force). This recommendation aims to optimize sensor systems such as joysticks in medical devices in terms of safety, ease of use, and adaptability.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

In this study, different configurations based on linear fiber lasers were proposed and experimentally demonstrated to measure the concentration of paracetamol liquid solutions in a range of 52.61 to 201.33 g/kg. The optical gain was provided by a commercial bidirectional Erbium-Doped Fiber Amplifier (EDFA) and the linear cavity was obtained using two commercial Fiber Bragg Gratings (FBGs). The main difference of each configuration was the coupling ratio of the optical coupler used to extract the system signal. The sensing head corresponded to a Single-Mode Fiber (SMF) tip that worked as an intensity sensor. The results reveal that, despite the optical coupler used (50:50, 60:40, 70:30 or 80:20), all the configurations reached the laser condition, however, the concentration sensing was only possible using a laser drive current near to the threshold value. The configurations using a 70:30 and an 80:20 optical coupler allowed to perform paracetamol concentration measurements with a higher sensitivity of (-3.00±0.24) pW/(g/kg). In terms of resolution, the highest value obtained was 1.75 g/kg, when it was extracted 20% of the output power to the linear cavity fiber laser configuration.

A standard method assessing postural control is the measurement in standing position. However, the implementation is usually only possible to a limited extent. Recording of postural control directly on the trunk, in seated position, could provide an alternative diagnostic method for quantifying neuromuscular control. Comparison of the measurements of Center of Pressure (CoP) in standing and seated position was performed on 66 healthy adult subjects. Reliability of measurements in seated position was tested on 23 subjects. In addition, the extension force of all test subjects was recorded. The assessments of CoP fluctuations in standing and seated position showed adequate agreement (deviation 9.1%). Furthermore, good internal consistencies with a sufficient test re test reliability could be demonstrated for the measurements in seated position. Both CoP measurement methods showed a comparable Spearman correlation to obtained extension force measurements (standing: 0.24, seated: 0.23). Our results show that recording CoP flucutations in the seated position is a reliable and valid additional method to measurements in the single legged stance. It could serve as an additional alternative to quantify neuromuscular control in impaired patients in whom single-leg stance cannot be performed adequately. In addition, the measurement in sitting position enables the direct recording of neuromuscular control on the trunk.

In this study, a carbon fiber microelectrode (CF) was applied for the investigation of electrochemical behavior and determination of natural antioxidant, apocynin (APO). Given the limited solubility of APO in water, a mixture of anhydrous acetic acid (AcH) with 20%, v/v acetonitrile (AN) and 0.1 mol L-1 sodium acetate (AcNa) was used. The electrochemical properties of APO were examined through linear sweep voltammetry (LSV), differential pulse voltammetry (DPV), and cyclic voltammetry (CV). The anodic oxidation of APO, which is the basis of the method used, proved to be diffusion-controlled and proceeded with a two-electron and one proton exchange. Both radicals and radical cations, arising from the first and second step of electrode reactions, respectively, underwent subsequent chemical transformations to yield more stable final products (EqCiEiCi mechanism). Using optimized DPV conditions, the anodic peak current of APO at potential of 0.925 V vs Ag/AgCl showed a good linear response within the concentration range of 2.7×10-6 – 2.6×10-4 mol L-1. The detection and quantification limits were determined as 8.9×10-7 and 2.7×10-6 mol L-1, respectively. The developed DPV method enabled the successful determination of APO in herbal extracts and in dietary supplements. It should be noted that this is the first method of voltammetric determination of APO.

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

This study's objective was to propose the use of textile braiding manufacturing methods, thus facilitating the application of the high precision and accurate measurability of optical fiber Bragg grating sensors to various structures. The purpose of this study was to Combine 3d braid processing with the optical Bragg grating sensor's accurate metrology. Out of limits of the sensor's epoxy attachment methods, the textile braiding method can make applicable scope diversify. The braiding processing is capable of designing a 3D fabric module processing, multiple objective mechanical fiber arrangement, and material characteristics. Optical stress-strain response conditions were explored through the optimization of design elements between the Bragg grating sensor and braiding. For this study, Bragg grating sensors were located 75% apart from the fiber center. The sensor core structure is helical of 1.54 pitch. A polyurethane synthetic yarn was braided together with the sensor on the Weaving machine core part in a braiding. Prototyping results, a negative Poisson's ratio makes curled the braided Bragg grating sensor. The number of polyurethane string yarns has been conducted the role of wrap angle in braiding. The 12 strands condition showed an increase in double stress-strain response rate at a Poisson ratio of 1.3%, and 16 strands condition was found to affect the sensor with noise at a Poisson ratio of 1.5%. This study can suggest applying braid processing of the Bragg grating sensor, which is expected to create and develop a new monitoring sensor.

This study's objective was to propose the use of textile braiding manufacturing methods, thus facilitating the application of the high precision and accurate measurability of optical fiber Bragg grating sensors to various structures.The purpose of this study was to Combine 3d braid processing with the optical Bragg grating sensor's accurate metrology. Out of limits of the sensor's epoxy attachment methods, the textile braiding method can make applicable scope diversify. The braiding processing is capable of designing a 3D fabric module processing, multiple objective mechanical fiber arrangement, and material characteristics. Optical stress-strain response conditions were explored through the optimization of design elements between the Bragg grating sensor and braiding. For this study, Bragg grating sensors were located 75% apart from the fiber center. The sensor core structure is helical of 1.54 pitch. A polyurethane synthetic yarn was braided together with the sensor on the Weaving machine core part in a braiding.Prototyping results, a negative Poisson's ratio makes curled the braided Bragg grating sensor. The number of polyurethan string yarns has been conducted the role of wrap angle in braiding. The 12 strands condition showed an increase in double stress-strain response rate at a Poisson ratio of 1.3%, and 16 strands condition was found to affect the sensor with noise at a Poisson ratio of 1.5%. This study can suggest applying braid processing of the Bragg grating sensor, which is expected to create and develop a new monitoring sensor.

Adipose tissue-derived stem cells (ADSCs) represent a subset of mesenchymal stem cells in every adipose compartment throughout the body. ADSCs can differentiate into various cell types, including chondrocytes, osteocytes, myocytes, and adipocytes. Moreover, they exhibit a notable potential to differentiate in vitro into cells from other germinal lineages, including endothelial cells and neurons. ADSCs have a wide range of clinical applications, from breast surgery to chronic wounds. Furthermore, they are a promising cell population for future tissue-engineering uses. Accumulating evidence indicates decreased proliferation and differentiation potential of ADSCs with increasing age, body mass index, diabetes mellitus, metabolic syndrome, or exposure to radiotherapy. Therefore, recent literature thoroughly investigates this cell population's senescence mechanisms and how they can hinder their possible therapeutic applications. This review will discuss the biological mechanisms and the physio-pathological causes behind ADSC senescence and how they can impact cellular functionality. Moreover, we will examine the possible strategies to invert these processes, re-establishing the full regenerative potential of this progenitor population.

Technological advancements in the Internet of Things (IoT), unmanned aerial vehicles (UAVs), and novel technological tools have transformed disaster management practices from localized approaches to a global framework. These innovations necessitate a unified understanding and application of diverse methodologies at an international level, ensuring they are accessible and operational across different sectors. This integration is crucial not only for technical personnel but also for medical teams, who play a pivotal role in disaster response and management. By fostering a comprehensive grasp of these methods, we can enhance coordination, efficiency, and effectiveness in addressing disasters on a global scale. The authors aimed to provide a comprehensive overview of emerging techniques that are driving shifts in strategic approaches and treatment technologies. Recognized as a domain of continuous research and development, this overview, by necessity, remains an incomplete snapshot of an evolving field. It highlights the dynamic nature of technological and strategic advancements, underscoring the importance of ongoing investigation and innovation to stay abreast of current trends and future directions. The article also highlights the importance of international collaboration beyond societal and national boundaries A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

Currently, the use of recycled waste plastic in road construction is not just considered ecofriendly but also considered advantageous for improving road performance over time. This research explores using recycled plastic bags, made of low-density polyethylene (LDPE), in asphalt mixtures to improve road performance and manage waste. The study aims to assess the effects of incorporating different amounts of shredded waste plastic into asphalt mixes and determine the optimal percentage. The aggregate used was obtained from Sargodha quarry Pakistan and asphalt used was 60/70 grade obtained from national refinery limited Pakistan. Using the Marshall mix design, the optimum bitumen content (OBC) was found to be 4.5% of the asphalt mix weight. Thirty samples were tested with waste plastic proportions of 6%, 8%, 10%, 12%, and 14% of OBC weight, along with a standard mix. Tests on stability, bulk density, flow, and air voids showed that a 10% plastic content significantly enhances asphalt performance, increasing stability by around 25%. The study recommends using 10% plastic by OBC weight in asphalt mixes for better performance and suggests further research on optimal incorporation techniques of waste materials in asphalt mixtures.

A novel fiber optic sensing technology for high frequency dynamics detection is proposed in this paper, specifically tailored for structural health monitoring applications based on strain wave analysis, including both passive impact identification and active Lamb wave monitoring. The sensing solution relies on a fiber optic-based interferometric architecture associated to an innovative coherent detection scheme, which retrieves in a completely passive way the high-frequency phase information of the received optical signal. The optical fiber can be arranged into different configurations in order to meet the requirement of the specific application, the sensor sensitivity being maximized while still ensuring a limited gauge length if a local measure is required. For the active Lamb wave monitoring, this results in a sensing fiber arranged in multiple loops glued on an aluminum thin panel in order to increase the phase signal relative only to the sensing points of interest. Instead, for passive impact identification, the sensitivity is simply increased by exploiting a longer gauge length glued to the structure. The fiber optic coherent (FOC) sensor detects the strain waves emitted by a piezoelectric transducer placed on the aluminum panel or generated by an impulse hammer, respectively. The FOC sensor measurements have been compared with both a numerical model based on Finite Elements and traditional piezoelectric sensors, confirming a very good agreement between experimental and simulated results for both the active and passive impact monitoring scenarios.

Electrowetting display (EWD) device is a new type of electrowetting-on-dielectric (EWOD) equipment which can achieve a paper-like display effect under the control of electric field. In this microfluidic system, the stability of grayscale could be affected by various factors, such as the physicochemical properties of materials, device structure, and electric field distribution. To improve the grayscale stability of active matrix electrowetting displays (AM-EWDs), the impact of different polarities of driving voltage on oil backflow was investigated in this study. Based on the driving principles of AM-EWD, an optimized inter-frame bipolar reset driving waveform was designed to overcome oil backflow. The proposed driving waveform maintained the stability of the oil state by periodically and rapidly releasing trapped charges in the dielectric layer through a reverse driving voltage. Additionally, the effect of feed through voltage on the pixel driving voltage was eliminated by compensating for the driving voltage on common electrode. Finally, the performance of the designed driving waveform was evaluated with a 6-inch AM-EWD driving platform. Compared to the conventional unipolar reset driving waveform, the backflow speed decreased by 2.70 a.u./s. The standard deviation of the display luminance was also reduced by 11.24 a.u. Experimental results indicated that both the oil backflow speed and the fluctuation range of luminance were effectively suppressed by the proposed driving waveform.

Femtosecond laser two-photon polymerization (TPP) technology, known for its high precision and capability to fabricate arbitrary 3D structures, has been widely applied in the production of various micro-nano optical devices, achieving significant advancements particularly in the field of photonic wire bonding (PWB) for optical interconnects. Currently, research on optimizing both the optical loss and production reliability of polymeric photonic wires is still in its early stages. One of the key challenges is that inadequate metrology methods cannot meet the demand for multiphysical measurements in practical scenarios. This study utilizes in-situ scanning electron microscopy (SEM), for the first time, to monitor the working PWBs fabricated by TPP technology at the microscale. Optical and mechanical measurements are made simultaneously to evaluate the production qualities and to study the multiphysical coupling effects of PWBs. The results reveal that photonic wires with larger local curvature radii are more prone to plastic failure, while those with smaller local curvature radii recover elastically. Furthermore, larger cross-sectional dimensions contribute dominantly to the improved mechanical robustness. The optical loss deterioration of the elastically deformed photonic wire is only temporary, which can be fully recovered when the load is removed. After further optimization based on the results of multiphysical metrology, the PWBs fabricated in this work achieve a minimum insertion loss of 0.6 dB. In this study, the multiphysical analysis of PWBs carried out by in-situ SEM metrology offers a novel perspective for optimizing the design and performance of microscale polymeric waveguides, which could potentially promote the mass production reliability of TPP technology in the field of chip-level optical interconnection.

This study introduces a Fiber Specklegram Sensor (FSS) design for temperature measurement utilizing a single-multi-single mode optical fiber configuration. FSS technology offers unique advantages for potential development into portable sensing systems. This investigation explores an FSS design compatible with miniaturization by optimizing the interrogation system based on the relationship between speckle grain size and filtering fiber area. Temperature variations are detected through fluctuations in optical power at the sensor output, offering a simple and reduced interrogation scheme. The performance of the FSS is assessed through post-calibration measurements compared to a commercial Fiber Bragg Grating (FBG) sensor, demonstrating comparable results. These findings pave the way for compact and portable fiber optic temperature sensing systems leveraging FSS advantages while maintaining compatibility with established fiber optic measurements.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.

This paper reports on the fabrication of alumina doped preforms using MCVD-vapor phase chelate delivery system with Al(acac)3 as the precursor. The objectives of the work are to study the deposition process, the efficiency of the fabrication process, and the quality of the fabricated fiber preforms. Two parameters are studied, Al(acac)3 sublimator temperature (TAl°C) and deposition direction (i.e. downstream and upstream). Other parameters such as oxygen flow and deposition temperature are fixed. The results showed that a high uniformity of refractive index difference (%RSD &lt; 2%) and core size (%RSD &lt; 2.4%) was obtained along the preform length using downstream deposition while for the combined upstream and downstream deposition the uniformity was deteriorated. The process efficiency was found to be about 21% for TAl°C of 185°C and downstream deposition. From the EDX elemental analysis, the refractive index was found to increase by 0.0025 per mole percent of alumina.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

Fiber-based flexible sensors have promising applications potential in human motion and healthcare monitoring, owing to their merits of lightweight, flexibility, and easy processing. Now, high-performance elastic fiber-based strain sensors with high sensitivity, large working range and excellent durability are in great demand. Herein, we have easily and quickly prepared a highly-sensitive, durable fiber-based strain sensor by dip-coating of highly-stretchable polyurethane (PU) elastic fiber in MXene/ waterborne polyurethane (WPU) dispersion solution. Benefiting from the electrostatic repulsion force between the negatively charged WPU and MXene sheets in the mixed solution, very homogeneous and stable MXene/WPU dispersion was successfully obtained and the interconnected conducting networks were correspondingly formed in coated MXene/WPU shell layer, which makes as-prepared strain sensor exhibit a gauge factor of over 960, a large sensing range of over 90% and detection limit as low as 0.5% strain. As elastic fiber and mixed solution have the same polymer constitute, tight bonding of MXene/WPU conductive composite on PU fibers was achieved, enabling the as-prepared strain sensor endure over 2500 stretching-releasing cycles and thus show good durability. Full-scale human motion detection was also performed by the strain sensor, and a body posture monitoring, analysis, and correction prototype system was developed via embedding the fiber-based strain sensors into sweater, strongly indicating the great application prospect in exercise, sports and healthcare.

The calibration of length is related to the national economy and people's livelihood. The traditional calibration of length value was sent the uncalibrated instrument to the laboratory and the intrinsic error of the tested instrument was obtained in the laboratory. However, calibrating the instrument in the site produced additional error. In this article, a remote calibration method of length measurement based on optical fiber information transmission following with a proof of principle system was studied to reduce the additional error. The 1.0-level displacement guide rail was calibrated according to this method. The results showed that the relative error of guide rail displacement under different lengths was within 0.6%. The expanded uncertainties of 10 μm, 100 μm and 1 mm were analyzed respectively. The calibration results meet the actual standards of the guide rail. This optical method is a good candidate for remote calibration.

This work presents results of property researches of fabricated samples of silica few-mode optical fiber (FMF) with induced chirality under twisting 10 and 66 revolutions per meter, core diameter 11 µm, typical “telecommunication” cladding diameter 125 µm and improved height of quasi-step refractive index profile. Proposed FMF supports 4 guided modes over “C”-band. We represent results of computed characteristics, as well as experimentally measured spectral responses of laser-excited optical signals, including researches and analysis of few-mode effects, occurring after fiber Bragg grating writing.

Optical fiber sensors have become a widely-used tool to perform life-long monitoring of large structures. Different set-ups of sensors can be used to obtain information at different scopes. In this paper, the application of a portable Brillouin optical time domain analysis sensor applied to reinforced concrete beams is presented. The sensor is made up of a single-mode optical fiber applied to the structure that enables the measurement of tensile and compressive axial strain along the beams. The fiber is embedded into a concrete casting and fixed along the reinforcement bars so that a complete correlation can be obtained regarding strain and displacements in linear and non-linear flexural response. The use of four sensing fibers positioned along the beam's length at different vertical positions makes it possible to read the strain variation within the cross-section. In accordance with Bernoulli’s hypothesis, this allows curvature diagrams to be obtained across the structure. The measured curvature is used to set up the moment–curvature relationship, which highlights the possibility of the sensor monitoring structures continuously in space and time.

Turbidity is an important water quality parameter, especially for drinking water. The ability to actively monitor the turbidity level in Drinking Water Distribution Systems is of critical importance to the safety and wellbeing of the public. Traditional turbidity monitoring methods involve manual collection of water samples at set locations and times followed by laboratory analysis, which are labor intensive and time consuming. Fiber-optic measurement permits real-time, in-situ turbidity monitoring. But the current technology is based on plastic fibers, which suffer from high optical attenuation and hence are unsuitable for large-scale remote monitoring. In this paper, we report the demonstration of a fiber-optic turbidity sensor based on multi-mode glass fibers. The system uses a single fiber to both deliver laser light into the water sample and collect the back-scattered light for detection. A balanced-detection scheme is utilized to remove the common-mode noise to enhance the turbidity sensitivity. Highly linear turbidity responses are obtained and a turbidity resolution as low as 0.1 NTU is achieved. The test unit is also shown to have excellent reproducibility against repeated measurements and good stability against temperature changes. Turbidity measurement in real environmental matrices such as tap water and pond water is also reported with an assessment of the impact of flow rate. This work demonstrates the feasibility of future large scale distributed fiber-optic turbidity monitoring networks.

A realistic implementation of an all-fiber CO₂ sensor, using 74 cm of hollow core PCF fiber as the cavity for light/gas interaction, has been implemented. It is based on CO₂ absorbance in the 2 μm region. The working range is from 2% to 100% CO₂ concentration at 1 atm total pressure. The response time obtained was 10 min. The use of an FBG tuned fiber ring laser, specifically designed for this application, is discussed and preliminary results with this laser are also presented.

Background: Extracellular Vesicles are pivotal mediators in intercellular communication, facilitating the exchange of biological information among healthy, pathological and tumor cells. Between the diverse subtypes of extracellular vesicles, exosomes have unique properties, clinical and therapeutical applications, even towards cancer. Breast cancer ranks as one of the most prevalent malignancies across the globe. Both the tumor core and its surrounding microenvironment engage in a complex, orchestrated interaction that facilitates the cancer’s growth and spread. Methods: The most valuable and significant PubMed Literature about extracellular vesicles and adipose–derived stem cells exosomes was selected and analyzed in order to report their biological properties and potential applications, in particular on the Triple–Negative Breast Cancer. Results: Adipose–derived stem cells exosomes represent a potential tool to target the tumor core of the Triple–Negative Breast Cancer, its microenvironment and surrounding tissues including metastasis. The authors are developing a supportive Triple–Adipose–derived stem cells Exosomes [T.A.E.] Technology against breast cancer in order to perform a selective preconditioning of the cancer before or while the traditional oncological treatments are running. Conclusion: The possibility to exploit the impact of Adipose–derived stem cells exosomes within the T.A.E. Technology against the Triple–Negative breast cancer is real, highlighting a new era for supportive measures against breast cancer.Keywords: Extracellular vesicles; Exosomes; Adipose–derived stem cells, Tumor microenvironment, Triple–Negative Breast Cancer, T.A.E. Technology.

This study aims to construct simple devices to ascertain the concentrations of ammonium (NH4+) and nitrate (NO3-). The device structure comprises a visible and near-infrared absorption meas-urement room, along with an RGB (red, green, and blue) absorption measurement room, con-stituting the two measuring rooms. Both the measurement rooms are equipped with light sources and detectors configured to operate in opposed or thru-beam modes. A tiny processor is utilized for processing the measurements, with an algorithm implemented within its memory. During the algorithm development phase, ranges for measuring the quantity of nutrients were categorized using a discriminant analysis approach. Thirty percent of the soil sample data were utilized as verification data, while the remaining 70 percent served as training data. Nutrient content values from reliable measuring instruments were incorporated into all datasets. Discriminant analysis was employed to classify the amount of NH4+ into five ranges based on the test results. When tested with soil samples, the accuracy was 66.13% compared to the reference value of a reliable measuring device. Similarly, NO3- was classified into four ranges with an accuracy of 81% com-pared to the reference value of a reliable measuring device.

Luminescent carbon dots (CDs) were locally synthesized in the core of CYTOP fibers using IR femtosecond laser direct writing (FLDW), a one-step simple method serving as a post-treatment of the genuine fiber. This approach enables the creation of several types of modifications such as ellipsoid voids. The CDs and photoluminescence (PL) distribute at the periphery of the voids. The PL spectral properties were studied through Excitation Emission Matrix in the visible range and excitation/emission spectrum in UV/visible range. Our finding reveals the presence of at least 3 distinct luminescent species, facilitating a broad excitation range extending from UV to green, and light emission spanning from blue to red. The average laser power and dose influence the quantity and ratio of these luminescent CD species. Additionally, we measured the spatially resolved lifetime of the luminescence during and after the irradiation. We found longer lifetimes at the periphery of the laser-induced modified regions and shorter ones closer to the center, with a dominant lifetime ~ 2ns. Notably, unlike many other luminophores, these laser-induced CDs are insensitive to oxygen, enhancing their potential for display or data storage applications.

Polarimetry is used to determine the Stokes parameters of a laser beam. Once all four S0,1,2,3 parameters are determined, the state of polarisation is established. Upon reflection of a laser beam with the defined S polarisation state, the directly measured S parameters can be used to determine the optical properties of the surface, which modified the S-state upon reflection. Here, we demonstrate polarimetry for the determination of surface anisotropies related to birefringence and dichroism from different materials, which have a common feature of linear patterns of different alignments and scales. It is shown that polarimetry in the back-reflected light is complementary to ellipsometry and four-polarisation camera imaging.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high precision seawater refractive index measurement. In this paper, we propose a method for measuring the refractive index of seawater based on a Position Sensitive Detector (PSD). Theoretical model is established to depict the correlation between laser spot displacement and refractive index change, utilizing a combination of position sensitive detector and laser beam deflection principle. Based on this optical measurement method, a seawater refractive index measurement system was established. To effectively enhance the sensitivity of refractive index detection, a focusing lens was incorporated into the optical path of the measuring system, and simulations were conducted to investigate the impact of focal length on refractive index sensitivity. The calibration experiment of the measuring system was performed based on the relationship between refractive index of seawater and underwater pressure (depth). By measuring laser spot displacement at different depths, changes in displacement with respect to both refractive index and depth were determined. Experimental results demonstrate that the system exhibits a sensitivity of 9.9277×10−9RIU (refractive index unit), the refractive index deviation due to stability is calculated as ±7.545×10−9RIU. Thereby the feasibility of highly sensitive measurement of seawater refractive index is verified.

We present an innovative method harnessing multistability within a diode-pumped erbium-doped fiber laser to construct logic gates. Our approach involves manipulating the intensity of external noise to regulate the probability of transitioning among four concurrent attractors. In this manner, we facilitate the realization of OR, AND, NOT, and NOR logic operations, aligning with the coexisting period-1, period-3, period-4, and period-5 orbits. Employing detrended fluctuation analysis, we establish equilibrium in the probability distributions of these states. The obtained results denote a substantial advancement in the field of optical logic gate development, representing a pivotal stride toward the seamless integration of an all-optical logic gate within laser oscillator-based systems.

Reconstruction of acoustic relaxation absorption curve is a powerful approach to ultrasonic gas sensing, but requires known of a series ultrasonic absorption at various frequencies around effective relaxation frequency. Ultrasonic transducer is a most widely deployed sensor for ultrasonic wave propagation measurement and works only at a fixed frequency or specific environment like water, so a large number of ultrasonic transducers operating at various frequencies are required to recover an acoustic absorption curve with a relative large bandwidth, which cannot suit for large-scale practical applications. This paper proposes a wideband ultrasonic sensor using a distributed Bragg reflector (DBR) fiber laser for gas concentration detection through acoustic relaxation absorption curve reconstruction. With a relative wide and flat frequency response, the DBR fiber laser sensor measures and restores a full acoustic relaxation absorption spectrum of CO2 using a decompression gas chamber between 0.1 and 1 atm to accommodate the main molecular relaxation processes, and interrogates with a non-equilibrium Mach-Zehnder (M-Z) interferometer to gain a sound pressure sensitivity of -45.4 dB. The measurement error of the acoustic relaxation absorption spectrum is less than 1.32%.

The Tisza River is the longest tributary of the Danube, draining the eastern part of the Carpathian Basin (Central Europe). Five countries share its catchment with different waste production and management practices. Large amounts of waste, including macroplastics (MaPs), are washed into the river. Some of the litter is trapped by the riparian vegetation forming litter accumulations. The study aimed to map the amount of litter by a citizen science program and remote sensing data and to compare the MaP data to the amount of microplastic fragments in sediments. Volunteers reported 3216 riverine litter accumulations from five countries along the entire length of the Tisza (2016–2022). The results suggest that low flow conditions (e.g., impoundment by dams) support litter and MaP trapping. The volume of large accumulations registered by the citizens showed a good correlation with the area of drifting litter revealed on Sentinel-2 images (2015–2021) using machine learning algorithms. Though the MaPs probably fragmentate during their fluvial transport, no clear connection was found between the volume of litter accumulations and the mean microplastic fragment content of sediments (2019–2022). The “Clean Tisza Map“ reveals the high degree of stranded pollutants along rivers and supports public cleanup activities.

In this paper, a sensitivity sensor of dual-core photonic crystal fiber (DC-PCF) filled with magnetic liquid is introduced and investigated by the finite element method (FEM). To regulate the energy coupling involving the two cores, the magnetic fluid is filled into the pore between the two cores. To adjust the coupling between the supermodes in the DC-PCF, the refractive index of the magnetic fluid-filled air hole may change due to the external magnetic field. This specifically created a magnetic fluid-filled DC-PCF, the magnetic fluid-filled hole is not used as the core for energy transmission, thus avoiding transmission loss. The dip wavelength and the magnetic field displayed an excellent linear connection between 80 and 260 Oe, depending on the numerical data. The detection sensitivity of the magnetic field reached 515.75 pm/Oe at a short fiber length of 482 m. The designed magnetic fluid-filled DC-PCF has high sensitivity and small volume and has great application prospects in medical and industrial field magnetic field detection.

The design and usage of the addressed combined fiber-optic sensors (ACFOS) and the multisensory control systems of the greenhouse gas concentration on their basis are investigated. The main development trend of the combined fiber-optic sensors (CFOS), consisting of the fiber Bragg grating (FBG) and the Fabry-Perot resonator (FPR), which are successively formed at the optical fiber end, is highlighted. The addressed fiber Bragg structures (AFBS) usage instead of the FBG in the CFOS leads not only to significant cheapening of the sensor system due to microwave photonics interrogating methods, but also to increasing its metrological characteristics. The structural scheme of the multisensory gas concentration monitoring system is suggested. The suggested scheme allows detecting four types of the greenhouse gases (СО2, NO2, CH4, OX) depending on the material and thickness of the polymer film, which is the FPR sensitive element. The usage of Karunen-Loeff transform (KLT), which allows separating each component contribution to the reflected spectrum according to its efficiency, is proposed. In the future, it allows determining the gas concentration at the AFBS address frequencies. The estimations have shown that the ACFOS design in the multisensory system allows measuring the environment temperature in the range of −60…+300 °C with an accuracy of 0.1–0.01 °C, and the gas concentration in the range of 10…90% with the accuracy of 0.1–0.5%.

In this paper, an ultracompact combined sensor for displacement and angle synchronous measurement is proposed based on self-imaging effect of optical microgratings. Using a two-grating structure, linear and angular displacement can be measured by detecting the change of phase and amplitude of the optical transmission respectively within one single structure in meantime. The optical transmitted properties of the two-grating structure are investigated in both theory and simulation. Simulated results indicate that, the optical transmission changes in a sinusoidal relationship to the input linear displacement. Meanwhile, the amplitude of the curve decreases with an input pitch angle, indicating the ability for synchronous measurement within one single compact structure. The synchronous measurement of the linear displacement and the angle is also demonstrated experimentally. The results show a resolution down to 4nm for linear displacement measurement, and a sensitivity of 0.26mV/arcsec within a range of ±1° for angle measurement. Benefitting from a simple common-path structure without using optical components including reflectors and polarizers, the sensor shows an ultrahigh compactness for multiple-degrees-of-freedom measuring, indicating the great potential for this sensor in the fields such as integrated mechanical positioning and semiconductor fabrication.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Background: Elevated respiratory rates (RR) have been described in several disease states, such as pneumonia, asthma and bronchiolitis. Despite this, there are few studies defining the range of RR found in healthy children. Available age percentiles for RR have been generated using methods that have the potential themselves to alter the rate. Aim: The aim of this study was to develop accurate percentile charts of RR specific for age in healthy children for potential use in pre-hospital care (first-aid), clinical medicine and for reference in respiratory research. Method: A newly developed optical respiratory sensor was used to measure RR which placed no restrictions on respiratory excursion. This technique enabled recording in awake children without the artefact of the observer’s presence on the subject’s RR. A cross-sectional sample of healthy children was obtained from maternity wards, childcare centres and schools in Brisbane, Queensland, Australia. Results: RR were observed in 560 awake and 103 sleeping children of which data from 343 awake and 94 sleeping children was used to create reference ranges for healthy children from newborn to 13 years of age. The recorded rates were significantly higher when children were awake compared to asleep. During quiet sleep, RR decreased from 40 (interquartile range 7) bpm at one month to 20 (interquartile range 3) in children aged 3 years. In awake children, RR ranged from a median of 40 bpm (interquartile range 18) at 1 year to 12 bpm (interquartile range 11) at 13 years respectively. Conclusion: The optical sensor was found to be an appropriate respiratory transducer, capable of measuring RR and reducing artefact by the subjective responses of alert children. The centile charts will be helpful as an aid to detecting abnormal RR in children and will contribute to further systematic reviews related to this vital sign.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

Introduction This study was conducted to validate the findings of a prior study published in JDD in September 2023, which reported that a topical firming and toning body lotion (FTB – SkinMedica®, Allergan Aesthetics, an AbbVie Company, Irvine, CA) upregulated several genes in a UV irradiated 3D full-thickness human skin model, outperforming other products, including TransFORM Body Treatment with TriHex Technology® (ATF – Alastin Skincare®, a Galderma company Fort Worth, Texas, USA ). Given the unique response reported for FTB, we conducted this study to assess the reproducibility of these results and explore gene expression at multiple time points, along with validating protein expression in an ex vivo model. Materials and Methods Experiments were conducted using an ex vivo model with photodamaged skin from facelift patients, under an Institutional Review Board approved study. Skin samples were processed, cultured in transwells with Skin Media, and treated daily with either TransFORM or FTB for 7 days. A control group was left untreated. Gene expression was assessed using RT-PCR on days 1 and 3, immunofluorescence after 3 and 7 days of treatment. Skin samples were fixed, paraffin-embedded, sectioned, and stained with an anti-tropoelastin antibody. Fluorescence detection and imaging were conducted to assess protein expression changes. Results Gene expression data from our study and the initial study showed a few similarities but multiple discrepancies. In particular, as opposed to results previously reported at only the 24-hour time point, additional time points showed complete reversal of many of these results. For example, COL1A1 expression at 24 hours was similar for FTB in both studies but differed for TransFORM which showed higher levels at 24 hours. However, at day 3, COL1A1 expression decreased markedly for FTB and was sustained for TransFORM. Other genes, such as COL3A1, COL5, ELN, VEGFC, ATG7, ATG12, BECN1, POMP, PSMB5, and PSMB6, exhibited varying expression patterns between the studies and across different time points. From a translational perspective, histological analysis showed that TransFORM enhanced elastin fiber presence in the dermal-epidermal junction (DEJ) more effectively than FTB at both day 3 and day 7. FTB-treated samples maintained a gap in the DEJ, while TransFORM-treated samples exhibited increased cellular proliferation and DEJ undulation, indicative of a healthier regenerative response. Conclusion This study highlights the problems of examining data and drawing conclusions using a single point of examination. In addition, when a study reports positive results for only 1 product among a range of 8 competitive products, further questioning is essential to exclude the possibility of the experimental model favoring that particular product. The additional 3-day timepoint and further translational examination of histological changes, paints a completely different picture to that reported in the prior publication TransFORM outperformed FTB in most gene expression and histological parameters when assessed over multiple time points in a physiologically relevant ex vivo model.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

For the numerical simulation of components made of short fiber-reinforced composites the correct prediction of the deformation including the elastic and plastic behavior and its spatial distribution is essential. When using purely deterministic modeling approaches the information of the probabilistic microstructure is not included in the simulation process. One possible approach for the integration of stochastic information is the use of random fields. In this study numerical simulations of tensile test specimens are conducted utilizing a finite deformation elastic-ideal plastic material model. A selection of the material parameters covering the elastic and plastic domain are represented by cross-correlated second-order Gaussian random fields to incorporate the probabilistic nature of the material parameters. To validate the modeling approach tensile tests until failure are carried out experimentally, that confirm the assumption of spatially distributed material behavior in both the elastic and plastic domain. Since the correlation lengths of the random fields cannot be determined by pure analytic treatments, additionally numerical simulations are performed for different values of the correlation length. The numerical simulations endorse the influence of the correlation length on the overall behavior. For a correlation length of 5mm a good conformity with the experimental results is obtained. Therefore, it is concluded, that the presented modeling approach is suitable to predict the elastic and plastic deformation of a set of tensile test specimens made of short fiber-reinforced composite sufficiently.

Against the background of the sky, imaging and perception of aircraft are cru- cial. Among these, the location of aircrafts is not a very difficult problem in general, because that deep learning algorithms and object detection models based on convolutional neural network(CNN) are ever-evolving. In order to have a better identification of various aircrafts, or to accurately locate different types of flying targets in the sky, it becomes significant to distinguish and recognize different types of aircrafts. One question is that, distinguishing and recognizing between sub-categories of aircrafts pose great challenges. Although fine-grained recognition focuses on exploring and studying such problems, aircrafts under different sub-categories and granularities lead us to rethink the application of features. We noticed that features in swin-transformer demonstrates the under- standing and processing of images, fully showcasing the encoding and indexing of information. Through this research and proposed approach, we discovered a better understanding of features encoding and use, which are inspired by the feature encoding and computation in swin-transformer. In our paper, our ap- proach has achieved effects on features encoded graphically, manifested from the architecture design and convolutional neural network computation, and outper- forms other famous fine-graiend classification models on this issue. Not only approach we proposed has demonstrated superior performance in fine-grained aicraft classification, but also the mechanisms of the feature encoding under different sample space partitions is revealed for this issue, which provides a re- search for the representation of aircraft fineness characteristics. The relationship between representation orientation of aircraft feature information under various grained divisions, shows that the recognition of different categories according to man-made, such as aircraft, can be achieved by means of the feature represen- tations studied in this paper, for more specific defined classification tasks and various man-made targets partition criteria, which may influences the princi- ple of design for calculation and feature extraction in fine-grained classification models.

The use of fiber optics as a tool for different kinds of geotechnical monitoring can become highly attractive and cost effective when compared to conventional instruments such as piezometers, inclinometers, among others. A single fiber optic cable may cover a larger monitoring area compared to conventional instrumentation, and the possibility of monitoring more than one physical quantity with the same fiber optic cable. Consulting the literature, it is possible to find several different examples where distributed fiber optic systems are being used. For the use of any sensor, a calibration curve is required. In the case of strain sensors, calibration is required to derive strain values from the frequency measurement quantity. However, fiber optic sensor cable manufacturers often do not provide their own calibration parameters and consult the values in specialized literature, which can result in monitoring errors. In this context, this article presents a bench adjusted for tests on single mode fiber optic cables, as well as results of tensile tests aimed at defining the function of strain variations of two different optical fiber cables, manufactured by different companies, using two different distributed interrogators. This paper also proposes a methodology for calibrating of the fiber optic cables deformation since the calibration parameters are provided by the cable manufacturers, which can result in errors depending on the application. It should be noted that there are few manufacturers of fiber optic cables aimed at application in civil engineering. Therefore, with the calibration methodology proposed in this paper, it is intended to transmit to the academic community the possibility of obtaining calibration parameters of any fiber optic cable, even those manufactured for telecommunications purposes and not only for cables manufactured with the intended use in civil engineering. Because of this fact, researchers will not be restricted to the acquisition of special cables for their applications. Based on the results, it was possible to conclude that the application of calibrated fiber optic sensors in experimental piles foundations is viable, in order to evaluate the load-displacement behavior of these elements, under different loading conditions.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

Quantum correlations, especially time correlations, are crucial in ghost imaging in order to significantly reduce the background noise on the one hand while increasing the imaging resolution. Moreover, the time correlations serve as a critical reference, distinguishing between signal and noise, which in turn enable clear visualization of biological samples. Quantum imaging also addresses the challenge involved in imaging delicate biological structures with minimal photon exposure and sample damage. Here we explore the recent progress in quantum correlation-based imaging, notably its impact on secure imaging and remote sensing protocols as well as on biological imaging. We also exploit the quantum characteristics of heralded single-photon sources (HSPS) combined with decoy-state methods for secure imaging. This method uses Quantum Key Distribution (QKD) principles to reduce measurement uncertainties and protect data integrity. It is highly effective in low-photon-number regimes for producing high-quality, noise-reduced images. The versatility of decoy-state methods with WCSs (WCS) is also discussed, highlighting their suitability for scenarios requiring higher photon numbers. We emphasize the dual advantages of these techniques: improving image quality through noise reduction and enhancing data security with quantum encryption, suggesting significant potential for quantum imaging in various applications, from delicate biological imaging to secure quantum communication.

The demand for improved service in mobile networks is always increasing. That means signal transmission with higher capacity is required. To achieve that goal a combined optical and wireless link using double polarization multiplexing has been developed. A high quality signal transmission is achieved by applying high polarization extinction ratio. The new concept is validated by experiments varying the bit rate and fiber length. A signal with 12 Gbit/s bit rate was transmitted over a 25 km long combined link with about 1.10-8 bit error rate. That result is much better than the already published data which were measured on links transmitting information with 2.5 Gbit/s bit rate. The polarization multiplexing technique is very practical for capacity enhancement in a specific section of an existing optical fiber by inserting a new link into it without deploying a new fiber.

Dermal water content is an important biophysical parameter in preserving skin integrity and preventing skin damage. Traditional electrical-based and open-chamber evaporimeters have several well-known limitations. In particular, such devices are costly, sizeable, and only provide arbitrary outputs. They also do not permit continuous and non-invasive monitoring of dermal water content, which can be beneficial for various consumer, clinical and cosmetic purposes. We report here on the design and development of a digital multi-wavelength optical sensor that performs continuous and non-invasive measurement of dermal water content. In-silico investigation on porcine skin was carried out using the Monte Carlo modelling strategy to evaluate the feasibility and characterise the sensor. Subsequently, an in-vitro experiment was carried out to evaluate the performance of the sensor and benchmark its accuracy against a high-end, broad band spectrophotometer. Reference measurements were made against gravimetric analysis. The results demonstrate that the developed sensor can deliver accurate, continuous, and non-invasive measurement of skin hydration through measurement of dermal water content. Remarkably, the novel design of the sensor exceeded the performance of the high-end spectrophotometer due to the important denoising effects of temporal averaging. The authors believe, in addition to wellbeing and skin health monitoring, the designed sensor can particularly facilitate disease management in patients presenting diabetes mellitus, hypothyroidism, malnutrition, and atopic dermatitis.