This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity and low cost. However, the thorniest issue for wider application of IRT is the quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Carbon Fiber Reinforced Polymer(CFRP) embedded with flat bottom holes were designed via Finite Element Method (FEM) modeling in order to precisely control the depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

The prevalence of hepatitis B and delta viruses (HBV/HDV) among people who use drugs (PWUD) remains largely unknown. In the context of one Philadelphia-based harm reduction organization (HRO), this study aimed to assess HBV/HDV prevalence and facilitate linkage to care. Participants completed a demographic HBV/HDV risk factor survey and were screened for HBV and reflexively for HDV if positive for HBV surface antigen or isolated core antibody. Fisher’s exact tests and regression were used to understand relationships between risks and HBV blood markers. Of the 498 participants, 126 (25.3%) were susceptible to HBV, 52.6% had been vaccinated against HBV, and 17.9% had recovered from a past infection. Eleven (2.2%) participants tested positive for isolated HBV core antibody, 10 (2.0%) for HBV surface antigen, and one (0.2%) for HDV antibody. History of incarceration was associated with current HBV infection, while transactional sex and experience of homelessness were predictive of previous exposure. This study found high rates of current and past HBV infection, and a 10% HBV/HDV co-infection rate. Despite availability of vaccine, one quarter of participants remained vulnerable to infection. Findings demonstrate the need to improve low-threshold HBV/HDV screening, vaccination, and linkage to care among PWUD. The study also identified gaps in the HBV/HDV care cascade, including lack of point-of-care diagnostics and lack of support for HROs to provide HBV services.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

Accurate prediction of defects in software components plays a vital role in administrating the quality of the quality and efficiency of the system to be developed. So we have written a systematic literature review in order to evaluate the four main defect prediction techniques. Defect prediction paves way for the testers to find bugs and modify them in order to achieve input to output conformance. In this paper we have discussed the open issues in predicting software defects and have provided with a detailed analyzation of different methods including Machine Learning, Integrated Approach, Cross-Project and Deep Forest algorithm in order to prevent these flaws. However, it is almost impossible to rule which method is better than the other so every technique can be analyzed separately and the best technique according to the problem at hand can be used or can be altered to create hybrid technique suitable for the cause.

Poultry farming in Slovakia has a tradition and an irreplaceable position to ensure rational nutrition for the population. In terms of a nutritional value, poultrymeat (Galliformes) contains a high amount of proteins, essential amino acids, essential unsaturated fatty acids, minerals, vitamins and a low fat content. Poultrymeat production has a relatively short reproductive cycle and thus allows regulating the demand and supply. The poultry market also influences the development of domestic consumption. According to the Statistical Office of the Slovak Republic, the consumption of meat has witnessed a persistent increase over the last 10 years. [1] According to the 2023 AVEC (The Voice of European Meat Sector) annual report, the consumption of poultrymeat in Slovakia was 20.0 kg per person per year. The average consumption in the EU-27 (2021) was 23.4 kg, with the countries with the highest consumption being Portugal (37.8 kg), Ireland (36.0 kg), Hungary (33.5 kg) and Spain (29.9 kg). On the other hand, the countries with the lowest consumption of poultrymeat, apart from Slovakia, also include Austria and Greece with a consumption of 21.5, resp. 21.0 kg [2]. The breeding of broiler chickens, as well as the production and placing on the market of poultrymeat must comply with the requirements laid down by legislation, while the compliance is regularly checked by the competent authorities.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

Currently, most deep learning methods cannot solve the problem of scarcity of industrial product defect samples and significant differences in characteristics. This paper proposes an unsupervised defect detection algorithm based on a reconstruction network, which is realized using only a large number of easily obtained defect-free sample data. The network includes two parts: image reconstruction and surface defect area detection. The reconstruction network is designed through a fully convolutional autoencoder with a lightweight structure. Only a small number of normal samples are used for training so that the reconstruction network can be A defect-free reconstructed image is generated. A function combining structural loss and L1 loss is proposed as the loss function of the reconstruction network to solve the problem of poor detection of irregular texture surface defects. Further, the residual of the reconstructed image and the image to be tested is used as the possible region of the defect, and conventional image operations can realize the location of the fault. The unsupervised defect detection algorithm of the proposed reconstruction network is used on multiple defect image sample sets. Compared with other similar algorithms, the results show that the unsupervised defect detection algorithm of the reconstructed network has strong robustness and accuracy.

Software defect prediction models enable test managers to predict defect-prone modules and assist with delivering quality products. A test manager would be willing to identify the attributes that can influence defect prediction and should be able to trust the model outcomes. The objective of this research is to create software defect prediction models with a focus on interpretability. Additionally, it aims to investigate the impact of size, complexity, and other source code metrics on the prediction of software defects. This research will also assess the reliability of cross-project defect prediction. Well-known machine learning techniques such as support vector machines, k-nearest neighbors, random forest classifiers, and artificial neural networks were applied to publicly available PROMISE datasets. The interpretability of this approach has been demonstrated by SHapley Additive exPlanations (SHAP) and local interpretable model-agnostic explanations (LIME) techniques. The developed interpretable software defect prediction models showed reliability on independent and cross-project data. Finally, the results demonstrate that static code metrics can contribute to the defect prediction models, and the inclusion of explainability assists in establishing trust in the developed models.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Methylmalonic acidemia (MMA), propionic acidemia (PA), and cobalamin C deficiency (cblC) share a defect in propionic acid metabolism. In addition, cblC is also involved in the process of homocysteine remethylation. These three diseases produce various phenotypes and complex downstream metabolic effects. In this study we used an untargeted metabolomics approach to investigate the biochemical differences and the possible connections with the pathophysiology of each disease. Untargeted urine metabolomic profiles of 21 patients (7 MMA, 7 PA, 7 cblC) were identified through statistical analysis (p<0.05; log2FC >|1|) and then used for the annotation. Annotated features were associated with different metabolic pathways potentially involved in the diseases development. Comparative statistic showed markedly different metabolomic profiles between MMA, PA and cblC, highlighting characteristic species for each disease. The most affected pathways were related to the metabolism of organic acids (MMA, PA, cblC), amino acids (MMA, PA, cblC), glycine and its conjugates (PA), transsulfuration pathway (cblC), oxidative processes (cblC) and neurosteroid hormones (cblC). The untargeted metabolomics study highlighted the presence of significant differences between the three diseases, pointing to the most relevant contrast of cblC profile compared to MMA and PA. Some new biomarkers are proposed for PA, while novel data regarding the alterations of steroid hormone profiles and biomarkers of oxidative stress were obtained for cblC disease. The elevation of neurosteroids in cblC may indicate a potential connection with the development of ocular and neuronal deterioration.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity, and low cost. However, the thorniest issue for the wider application of IRT is quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Finite Element Method (FEM) modeling provides the economic examination of the response pulsed thermography. In this work, Carbon Fiber Reinforced Polymer (CFRP) specimens embedded with flat bottom holes are stimulated by a FEM modeling (COMSOL) with precisely controlled depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the stimulated CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

Software defect prediction is an important means to guarantee software quality. Because there are no sufficient historical data within a project to train the classifier, cross-project defect prediction (CPDP) has been recognized as a fundamental approach. However, traditional defect prediction methods using feature attributes to represent samples, which can not avoid negative transferring, may result in poor performance model in CPDP. This paper proposes a multi-source cross-project defect prediction method based on dissimilarity space ( DM-CPDP). This method first uses the density-based clustering method to construct the prototype set with the cluster center of samples in the target set. Then, the arc-cosine kernel is used to form the dissimilarity space, and in this space the training set is obtained with the earth mover’s distance (EMD) method. For the unlabeled samples converted from the target set, the KNN algorithm is used to label those samples. Finally, we use TrAdaBoost method to establish the prediction model. The experimental results show that our approach has better performance than other traditional CPDP methods.

The timely diagnosis of defects at their incipient stage of formation is crucial to extend the life-cycle of technical appliances. This is the case of mechanical-related stress, either due to long aging degradation processes (e.g., corrosion) or in-operation forces (e.g., impact events), which might provoke detrimental damages, such as cracks, disbonding or delaminations, most commonly followed by the release of acoustic energy. The localization of these sources can be successfully fulfilled via adoption of Acoustic Emission (AE)-based inspection techniques through the computation of the Time of Arrival (ToA), namely the time at which the induced mechanical wave released at the occurrence of the acoustic event arrives to the acquisition unit. However, the accurate estimation of the ToA may be hampered by poor Signal-to-Noise ratios (SNRs). In these conditions, standard statistical methods typically fail. In this work, two alternative Deep Learning methods are proposed for ToA retrieval, namely a Dilated Convolutional Neural Network (DilCNN) and a Capsule Neural Network for ToA (CapsToA). These methods have the additional benefit of being portable on resource-constrained microprocessors. Their performance has been extensively studied on both synthetic and experimental data, focusing on the problem of ToA identification for the case of a metallic plate. Results show that the two novel methods can achieve localization errors which are up to 70% more precise than those yielded by conventional strategies, even when the SNR is severely compromised (i.e., down to 2 dB). Moreover, DilCNN and CapsNet have been implemented in a tiny machine learning environment and then deployed on microcontroller units, showing a negligible loss of performance with respect to offline realizations.

The lack of defect image data is one of the main factors affecting the accuracy of supervised deep learning-based defect detection models. In response to the insufficient training data of defect images with complex backgrounds such as rust and surface oil leakage in substation equipment, leading to poor performance of the detection model, this paper proposed a novel adversarial deep learning model for substation defect generation: ADD-GAN. In comparison to existing generative adversarial networks, this model generates defect images based on effectively segmented local areas of substation equipment images, avoiding image distortion caused by global style changes. Additionally, the model utilizes a joint discriminator for overall image and defect image to address the issue of low attention to local defect areas, thereby improving the loss of image features. This enhances the overall quality of generated images as well as locally generated defect images, ultimately improving image realism. Experimental results demonstrate that the YOLOV7 object detection model trained on the dataset generated using the ADD-GAN method achieves an mAP of 81.5% on the test dataset, representing an improvement of 9.6% over the original dataset, 5.7% over traditional augmentation methods, and 7% over typical adversarial deep learning methods. This confirms that the ADD-GAN method can generate a high-fidelity dataset of substation equipment defects.

Building defects are very prevalent and contribute significantly to a building's economic value. There are numerous information sources on building defects that have a lot potential for learning more about building defects. This study aimed to identify the information sources used in previous building defect studies and to identify the motivation for carrying out such studies. To fulfil this aim a scoping study was carried out. The information sources identified included insurance companies, private databases, questionnaire surveys, lawsuits, building surveys, client complaint forms, and maintenance reports. This study found that insurance company and client complaint forms include the largest collection of real building defect cases, but such databases may lack detailed descriptions of the causes of the defects. The main purposes of building defects studies identified here included design challenges, identification of defects, building maintenance management, quality management, systematization in data collection, providing an overview of typical defects, and classifying defects. Identification was found to be the most common purpose, indicating that the industry wants to learn more. This study identified research gaps in the climate perspective in relation to building defects. Most of the studies focused on the economical perspective, and none focused on the carbon footprint perspective.

In Taiwan, peanuts are classified by hand. The kernel quality is judged based on the appearance of peanuts. The identification takes considerable time and labor. Fatigue can induce misrecogni-tion or grade cognition instability due. Peanut defects are generally divided into health, underde-velopment, insect bite, and rupture. This study employed two imaging methods push-boom FX10 and Snapshot. Deep learning was used to detect peanut defects. A push-broom instrument was used for testing. There were 1,560 peanuts, including 240 good and 240 bad ones. There were a total of 1,080 good peanuts and bad peanuts in the test set data, the band selection was used, and a CNN model was built. Based on the results from three methods, 3DCNN could classify with 97%accuracy. The Snapshot was used to achieve the real-time design of a lightweight CNN model. Finally, five bands were selected using PCA, and the screening could be accurate and efficient. The maximum overall accuracy was about 98.5%. Kappa was 97.3% with real-time recognition. This will be a major advantage in the future practical application and commercialization processes. This technique can reduce labor costs, achieve intelligent detection and intelligent grading, and bring breakthroughs to smart agriculture for other crops as well.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.

The point cloud is a form of three-dimensional data that comprises various detailed features at multiple scales. Due to this characteristic and its irregularity, point cloud analysis based on deep learning is challenging. While previous works utilize the sampling-grouping operation of PointNet++ for feature description and then explore geometry by means of sophisticated feature extractors or deep networks, such operations fail to describe multi-scale features effectively. Additionally, these techniques have led to performance saturation. And it is difficult for standard MLPs to directly "mine" point cloud. To address above problems, we propose the Detail Activation (DA) module, which encodes data based on Fourier transform after sampling and grouping. We activate the channels at different frequency levels from low to high in the DA module to gradually recover finer point cloud details. As training progresses, the proposed Point-MDA can uncover local and global geometries of point cloud progressively. Our experiments show that Point-MDA achieves superior classification accuracy, outperforming PointNet++ by 3.3% and 7.9% in terms of overall accuracy on the ModelNet40 and ScanObjectNN dataset, respectively. Furthermore, it accomplishes this without employing complicated operations, while exploring the full potential of PointNet++.

A software defined radio (SDR) is a communication system that makes use of components that can be configured through software, in contrast to traditional systems where these components are variable through hardware, these radio devices are much more versatile, this article describes the factors that must be considered when implementing a communication system based on Software Defined Radios (SDR), in order to reduce the attenuation factors and thus obtain the maximum distance for a transmission of data effectively in the UHF band. The calculations made for the first Fresnel zone and for the design of the Ground Plane type antennas used in the transmission/reception stages of the x40 bladeRF platforms are also presented. The tests were carried out at the facilities of the Huarangal Nuclear Center of the Peruvian Institute of Nuclear Energy, obtaining favorable results that allow ratifying the versatility and performance of the SDRs.

The detection accuracy of bridge superficial defect using the deep neural network approach decreases significantly under light variation and weak texture condition. To address these issues, an enhanced intelligent detection method based on the YOLOv8 deep neural network is proposed in this study. Firstly, multi-branch coordinate attention (MBCA) is proposed to improve the accuracy of coordinate positioning by introducing a global perception module in coordinate attention mechanism. Furthermore, a deformable convolution based on MBCA is developed to improve the adaptability for complex feature shapes. Lastly, the deformable convolutional network-attention-YOLO (DAC-YOLO) detection algorithm is formed by replacing the deep C2F structure in the YOLOv8 architecture with deformable convolution. A supervised dataset consisting of 4794 bridge surface damage images is employed to verify the proposed method, and results show that it achieves improvements of 2.0% and 3.4% in mAP and R. Meanwhile, the model complexity decreases by 1.2G, increasing the detection speed by 3.5/f·s-1.

An 8-months old male American Staffordshire terrier was referred for a no weightbearing lameness of the right pelvic limb, hyperthermia, lethargy and inappetence caused by hematogenous osteomyelitis. Orthopedic, radiographic and tomographic examinations revealed a bone sequestrum of 4 x 1.4 cm and active periosteal reaction of the caudo-lateral cortical in the metaphysis and the distal third of the right femoral diaphysis, medullary osteolysis and interruption of the cranio-medial cortical profile, with involvement of the femoral trochlea leading to a secondary medial patella luxation. Once skeletally mature, after 4 months from surgical debridement and aggressive antibiotic therapy against Klebsiella oxytoca revealed by bacteriological exam, the patient underwent prosthetic surgery for the application of a custom-made patellar groove replacement (PGR) to fill the bone defect and restore the femoral trochlea surface. Despite the serious injury that afflicted the right pelvic limb, the surgery had satisfactory outcomes until the last 18-months postoperative follow up.

Point defects induced by doping rare earth elements RE (Nd, Er) into the magnesium oxide host were investigated by classical atomistic simulations utilising the General Utility Lattice Program (GULP). Formation and association energies were calculated for the potential defect structures. Both isolated defects and defect complexes were considered. The most energetically favourable structures of defect complexes were found for rare earth doped and Li co-doped systems. The correlation between the association energy and the structure of the defect complex was investigated. The influences of Li were revealed with respect to energy and structure. The simulation results contribute to the understanding of the point defects of doped MgO and how Li influences the doping of rare earth elements in the MgO host.

Defect detection plays a pivotal role in quality control for fabrics. In order to enhance the accuracy and efficiency of fabric defect detection, we have proposed the PRC-Light YOLO model for fabric defect detection and have established a detection system. Firstly, we add new convolution operators in Backbone for the YOLOv7 and integrate them with Extended-Efficient Layer Aggregation Network. This combination constructs a new feature extraction module that not only reduces the computational effort of the network model, but also extracts spatial features effectively. Secondly, we employ multi-branch dilated convolutions feature pyramid, and introduce lightweight upsampling operators to improve performance of the feature fusion network. This module achieves an expanded receptive field by generating real-time adaptive convolution kernels, allowing for the collection of crucial information from regions with a richer contextual context. To further minimize the computation during network model training, we adopt the HardSwish activation function. Finally, we apply the Wise-IOU v3 bounding box loss function as a dynamic non-monotonic focusing mechanism, which decreases adverse gradients from low-quality instances. We conduct data augmentation on real fabric dataset to raise the generalization capability of the PRC-Light YOLO model. Compared with the YOLOv7 model, numerous simulation experiments show that our proposed methods reduce the model’s parameters and computation by 18.03% and 20.53%, respectively. Simultaneously, there has been a 7.6% improvement in mAP.

Defect recognition in ballastless track structures, based on distributed acoustic sensors (DASs), was researched in order to improve detection efficiency and ensure the safe operation of trains on high-speed railways. A line in southern China was selected, and equipment was installed and debugged to collect the signals of trains and events along it. Track vibration signals were extracted by identifying a train track, denoising, framing and labeling to build a defect dataset. Time–frequency-domain statistical features, wavelet packet energy spectra and the MFCCs of vibration signals were extracted to form a multi-dimensional vector. An XGBoost model was trained and its accuracy reached 89.34%. A time-domain residual network (ResNet) that would expand the receptive field and test the accuracies obtained from convolution kernels of different sizes was proposed, and its accuracy reached 94.82%. In conclusion, both methods showed good performance with the built dataset. Additionally, the ResNet delivered more effective detection of DAS signals compared to conventional feature engineering methods.

Surface defect detection is a crucial step in the process of automotive wheel production. However, the task possesses challenges due to complex background and a wide range of defect types. In order to detect the defects on the wheel surface accurately and quickly, this paper proposes a YOLOv5-based algorithm for automotive wheel surface defect detection. The algorithm trains and tests the YOLOv5s model using the self-created automotive wheel surface defect dataset, which contains four kinds of defects: linear, dotted, sludge, pinhole. The extensive experimental results demonstrate that the deep learning network trained by our method can achieve an average accuracy of 71.7% and 57.14 FPS. Our findings prove that this detection algorithm performs better than other common target detection algorithms and meets the real-time requirements of industrial applications.

The success of a software system is highly dependent upon its quality which is a very critical aspect and is the ultimate goal to be achieved. Defect Management is the most important process in ensuring software quality, it involves defect detection, defect categorization, defect prioritization, defect removal and defect verification. The main purpose of this process is to develop and produce defect free or least defected software systems of high quality. It plays a vital role in gaining customer confidence and satisfaction which is essential for the reputation of the organization developing the system. The central objective of this study is to explain the importance of defect management and its impact on the quality of the software along with various defect management techniques to support the objective.

Interactions between mobile robots and human operators in common areas require a high safety especially in terms of trajectory planning, obstacle avoidance and mutual cooperation. In this connection the crossings of planned trajectories, their uncertainty based on model fluctuations, system noise and sensor noise,play an outstanding role. This paper discusses the calculation of expected areas of interactions du ring human-robot navigation with respect to fuzzy and noisy information. Expected crossing points of possible trajectories are nonlinearily associated with positions and orientations of robot and human. The nonlinear transformation of a noisy system input, such as directions of motion of human and robot, to a system output, the expected area of intersection of their trajectories, is done by two methods: statistical linearization and the sigma-point-transformation. For both approaches fuzzy approximations are presented and the inverse problem is discussed where the input distribution parameters are computed from given output distribution parameters.

Abstract: For the problem of small target of printed circuit board surface defects and low detection accuracy, the printed circuit board surface defect detection network DCR-YOLO is designed to meet the premise of real-time detection speed and effectively improve the detection accuracy. Firstly, the backbone feature extraction network DCR-backbone, consisting of two CR residual blocks and one common residual block, is used for small target defect extraction on printed circuit boards. Secondly, the SDDT-FPN feature fusion module is responsible for the fusion of high level features to low level features, while enhancing feature fusion for the feature fusion layer where the small target prediction head YOLO Head-P3 is located to further enhance the low level feature representation. the PCR module enhances the feature fusion mechanism between the backbone feature extraction network and the SDDT-FPN feature fusion module at different scales of feature layers. the C5ECA module is responsible for adaptive adjustment of feature weights and adaptive attention to the requirements of small target defect information, further enhancing the adaptive feature extraction capability of the feature fusion module. Finally, three YOLO-Heads are responsible for predicting small target defects for different scales. Experiments show that the DCR-YOLO network model detection Map reaches 98.58%, the model size is 7.73MB, which meets the lightweight requirement, and the detection speed reaches 103.15fps, which meets the application requirements for real-time detection of small target defects.

With the increasing occurrence of rotator cuff injuries every year, there is a great need for a reliable treatment option. Wharton’s Jelly contains several components that can positively impact the replacement and repair of musculoskeletal defects. The overall objective of this study is to evaluate the improvement of patient-reported pain scales after applying Wharton’s Jelly (WJ) in rotator cuff defects. Eighty-seven patients with rotator cuff defects who failed at least eight weeks of conservative treatment were selected from the retrospective repository. 2cc of WJ flowable allograft was applied to the specific affected anatomy, the most common being supraspinatus tendon, biceps tendon insertion, labral tear, and subscapularis tear. No adverse reactions were reported. Statistically significant improvements were found from the initial to Day 90 in all scales. Patient satisfaction was calculated using minimal clinically important differences. No statistically significant differences were found in mean changes between gender, BMI, and age. Scanning Electron Microscopy images reveal the similarities between the collagen matrix in WJ and the rotator cuff. The significant improvement in patient outcomes coincides with current literature analyzing WJ applications with other structural defects around the body. WJ is a promising alternative for musculoskeletal defects when the standard of care fails.

We investigate the impact of aging on exchangeable inter-arrival times in mixed renewal processes, exploring its implications for reliability and survival analysis. In this study, first, we revisit the definition of renewal point processes, where inter-event time intervals are considered as exchangeable non-negative random variables. Then, we define the concept of statistical aging as latency in the observational process of event counting. Latency affects event detection but preserves exchangeability. However, it may alter the statistical properties of inter-event time intervals. Our analytical and numerical assessments highlight the significance of aging in exchangeable lifetimes, offering insights into key metrics such as the failure survival function, renewal function, and hazard rate function. Through archetypal examples and empirical findings, we illustrate the implications of aging on renewal processes. In particular, employing a Bayesian perspective, we analyze high-frequency currency exchange rate data to assess the impact of aging on volatility risk evaluation. This study contributes novel insights to the literature of renewal theory and survival analysis, emphasizing the role of latency aging in stochastic point processes under exchangeability assumption.

We consider a Cauchy problem for differential equations in a Hilbert space $X$. The problem is stated in a time interval $I$, which can be finite or infinite. Weuse a fixed point argument for history-dependent operators to prove the unique solvability of the problem. Then, we state and prove convergence criteria for both a general fixed point problem and thecorresponding Cauchy problem. These criteria provide necessary and sufficient conditions on a sequence $\{u_n\}$ which guarantee its convergence to the solution of the corresponding problem, in the space of both continuous and continuously differentiable functions. We then specify our results in the study of a particular differential equation governed by two nonlinear operators. Finally, we provide an application in viscoelasticity and give a mechanical interpretation of the corresponding convergence result.

First came the digital banks without offices, and then the “fintech” companies that combined technology and finance to achieve greater efficiency and new business models. Later was the turn of transport and logistics, understood as the sector whose economic activities derived from the transport of people and goods, while on the one hand, it has had a new spring thanks to factors such as online sales. Then, perhaps catalyzed by the pandemic scenario, the turn has reached education, where years ago was only a complement of traditional education, now is a central part with multiple modern methodologies. Numerous studies exist about using or implementing these e-learning procedures, but technical analysis is barely found in references. This work aims to analyze the digital transformation of the main sectors of our society, including finances, transport, and education, together with several examples of how technology was helping to fight the pandemic scenario.

(1) Background: Considering highly selected patients with ductal carcinoma in situ (DCIS), active surveillance is a valid alternative to surgery. Our study is aimed at showing the reliability of post-biopsy complete lesion removal, documented by mammogram, as additional criterion to select these patients. (2) Methods: 2173 Vacuum Assisted Breast Biopsies (VABB) documented as DCIS have been reviewed. Surgery has been performed in all cases. We retrospectively collected the reports of post-VABB complete lesion removal and the histological results of the biopsy and surgery. We calculated the rate of upgrade of DCIS identified on VABB upon excision for patients with post-biopsy complete lesion removal and for those showing residual lesion. (3) Results: We observed 2173 cases of DCIS: 408 classified as low grade; 1262 as intermediate grade; 503 as high grade. The overall upgrading rate to invasive carcinoma was 15.2% (330/2173). The upgrade rate was significantly lower (8.2%) when considering patients showing mammographically documented complete removal of the lesion. (4) Conclusion: The absence of mammographically documented residual lesion following VABB is associated to a lower upgrading rate of DCIS to invasive carcinoma on surgical excision and should be considered when deciding the proper management DCIS diagnosis.

Insulator defect detection is of great significance to compromise the stability of the power transmission line. The state-of-the-art network of object detection, YOLOv5, has been widely used on insulator and defect detection. However, YOLOv5 network has some limitations like poor detection rate and high computational loads in detecting small insulator defects. To solve these problems, we proposed a light-weight network for insulator and defect detection. In this network, we introduced Ghost module into YOLOv5 backbone and neck to reduce the parameters and model size to enhance the performance in unmanned aerial vehicles (UAVs). Besides, we added small object detection anchors and layers for small defect detection. In addition, we optimized the backbone of YOLOv5 by applying convolutional block attention module (CBAM) to focus on critical information for insulator and defect detection and suppress uncritical information. The experiment result shows the mean average precision (mAP) 0.5 and the mAP0.5:0.95 of our model can reach 99.4% and 91.7%, the parameters and model weight are reduced to 3807372 and 8.79M, which can easily deploy to embedded devices like UAVs. And the speed of detection can reach 10.9ms/image, which can meet the real-time detection requirement.

Lymphedema is a chronic and debilitating disease that affects up to 250 million patients worldwide. Recent advances in understanding its pathophysiology, along with improved diagnosis and microsurgical techniques, have enhanced our ability to cope with the challenging task of treating this disease. This review provides an overview of the disease from a surgeon's point of view, including existing imaging modalities used for preoperative assessment, as well as surgical procedures used in its treatment. Advantages and drawbacks of various existing modalities used for pre or intraoperative assessment of lymphatic vessels are discussed. Lymphedema treatment has shifted from palliative debulking procedures (liposuction and direct excision) to those aimed at restoring lymphatic flow and countering the pathophysiology of the disease (lymphaticovenous anastomosis and vascularized lymph node transfer). A combination of both approaches can result in a synergistic benefit for patients and are discussed in this review. Despite recent advances, some controversies persist, and further studies are needed to better define surgical treatment algorithms.

In this paper, we investigate the structural, microstructural, dielectric, and energy storage properties of Nd and Mn co-doped Ba0.7Sr0.3TiO3 [(Ba0.7Sr0.3)1-xNdxTi1-yMnyO3 (BSNTM) ceramics (x = 0, 0.005, and y = 0, 0.0025, 0.005, and 0.01)] via a defect dipole engineering method. The complex defect dipoles (MnTi"-VO∙∙)∙ and (MnTi"-VO∙∙) between acceptor ions and oxygen vacancies capture electrons, enhancing the breakdown electric field and energy storage performances. XRD, Raman spectroscopy, and microscopic investigations of BSNTM ceramics revealed the formation of a tetragonal phase, increased oxygen vacancies, and reduced grain size with Mn dopant, respectively. The BSNTM ceramics with x=0.005 and y=0 exhibit a high dielectric constant of 2058 and a dielectric loss of 0.026 at 1 kHz. These values gradually decreased to 1876 and 0.019 for x=0.005 and y=0.01 due to the Mn2+ ions at Ti4+-site, which facilitates the formation of oxygen vacancies, and prevents the decrease of Ti4+. In addition, the defect dipoles act as a driving force for depolarization to tailor the domain formation energy and domain wall energy, which provides a high difference between the maximum polarization of Pmax and remnant polarization of Pr (ΔP=10.39 µC/cm2). Moreover, the complex defect dipoles with optimum oxygen vacancies in BSNTM ceramics can provide not only a high ΔP but also reduce grain size, which together improve the breakdown strength from 60.4 to 110.6 kV/cm, giving rise to a high energy storage density of 0.41 J/cm3 and high efficiency of 84.6% for x=0.005 and y=0.01. These findings demonstrate that defect dipoles engineering is an effective method to enhance the energy storage performance of dielectrics for capacitor applications.

Bioactive glass (BG) represents a promising biomaterial for bone healing; here injectable BG pastes biological properties were improved by 25 wt% gelatin or chitosan, as well as mechanical resistance was enhanced by adding 10 or 20 wt% 3-Glycidyloxypropyl trimethoxysilane (GPTMS) cross-linker. Composites exhibited bioactivity as apatite formation was observed by SEM and XRD after 14 days immersion in SBF; moreover, polymers did not enhance degradability as weight loss was >10% after 30 days in physiological conditions. BG-gelatin-20 wt% GPTMS composites demonstrated the highest compressive strength (4.8±0.5 MPa) in comparison with 100% BG control (1.9±0.1 MPa). Cytocompatibility was demonstrated towards human mesenchymal stem cells (hMSC), osteoblasts progenitors and endothelial cells. The presence of 20 wt% GPTMS conferred antibacterial properties thus inhibiting the joint pathogens Staphylococcus aureus and Staphylococcus epidermidis infection. Finally, hMSC osteogenesis was successfully supported in a 3D model as demonstrated by alkaline phosphatase release and osteogenic genes expression.

This report elucidates the first surgical correction of an infundibular muscular ventricular septal defect (VSD) in a one-year-old Ragdoll cat via cardiac arrest using cardiopulmonary bypass, a method that is rarely used in feline cardiac surgery. VSDs can lead to congestive heart failure and pulmonary hypertension, particularly in patients with large shunts. This case involved a VSD that was atypically located and classified under the Soto classification instead of the standard Kirklin classification. Detailed echocardiography revealed that the defect required intervention owing to left heart and main pulmonary artery enlargement. Despite the VSD being located on the contralateral side, as anticipated in the preoperative examinations, the choice of median sternotomy allowed for successful closure of the defect. Conversely, the insertion of two cannulas into the ascending aorta resulted in damage to the adjacent thoracic duct, causing transient chylothorax, which resolved with conservative treatment. Cardiac arrest induced by a cardioplegic solution facilitated the surgical procedure, although it has led to anemia in cats. However, on postoperative day 490, the patient exhibited only minor residual shunting with normalized heart size, and remained healthy. This technique appears to be a viable treatment option for congenital heart disease in cats.

Rationale: Chronic Granulomatous Disease (CGD) is a rare primary immunodeficiency. Although most mutations are linked to the X chromosome, therefore affecting males, there are autosomal recessive forms that therefore affect both sexes. Clinically it is characterized by recurrent and severe bacterial and fungal infections, with formation of granulomas, due to the inability of phagocytes to generate reactive oxygen compounds, necessary for the intracellular death of phagocytosed microorganisms. Patient concerns: We reported a 12-year-old boy with pneumonia with pneumatocele of possible staphylococcal etiology at one year of age, bilateral orchitis secondary to Salmonella with hematogenous spread, osteomyelitis due to Salmonella, gastroenteritis due to Salmonella enteritidis, liver abscesses due to Staphycococcus aureus and lymphomatoid papulosis and pyodermititis. Diagnoses: In the biochemical diagnosis, the presence of yellow dye (NBT) and absence of dark bluish black dye (formazan) was evidenced. Regarding the genetic diagnosis, the presence of the mutation in exon 10 of CYBB (OMIM 306400) (Xp21.1) that encodes the gp91phox protein was demonstrated. Interventions and outcomes: Treatment was started with trimethoprim/sulfamethoxazole 400/80 mg every 24 hours via oral, and antifungal prophylaxis with itraconazole 200 mg every 24 hours orally is added, after which he does not present serious bacterial or fungal infections, not being able to administer immunomodulatory treatment with recombinant human Interferon gamma-1b. Lessons: The clinical finding of frequent severe infections associated with granulomas, CGD should be suspected. Treatment of this primary immunodeficiency is trimethoprim/sulfamethoxazole and itraconazole. Importantly, it indicated that the mutation in exon 10 of CYBB (Xp21.1) that encodes the gp91phox might influence the pathogenesis of CGD.

Texture is essential information for image representation, capturing patterns, and structures. Consequently, texture plays a crucial role in the manufacturing industry and has been extensively studied in the fields of computer vision and pattern recognition. However, real-world textures are susceptible to defects, which can degrade the image quality and cause various issues. Therefore, there is a need for accurate and effective methods to detect texture defects. In this study, a simple autoencoder and Fourier transform were employed for texture defect detection. The proposed method combines Fourier transform analysis with the reconstructed template obtained from the simple autoencoder. Fourier transform is a powerful tool for analyzing the frequency domain of images and signals. Moreover, analyzing the frequency domain enables effective defect detection because texture defects often exhibit characteristic changes in specific frequency ranges. The proposed method demonstrates effectiveness and accuracy in detecting texture defects. Experimental results are presented to evaluate its performance and compare it with those of existing approaches.

A common challenge in real-world classification scenarios with sequentially appending target domain data is insufficient training datasets during the training phase. Therefore, conventional deep learning and transfer learning classifiers are not applicable especially when individual classes are not represented or are severely underrepresented at the outset. Domain Generalization approaches reach their limits when domain shifts become too large, making them occasionally unsuitable as well. In many (technical) domains, however, it is only the defect/ worn/ reject classes that are insufficiently represented, while the non-defect class is often available from the beginning. The proposed classification approach addresses such conditions and is based on a CNN encoder. Following a contrastive learning approach, it is trained with a modified triplet loss function using two datasets: Besides the non-defective target domain class (= 1st dataset), a state-of-the-art labeled source domain dataset that contains highly related classes (e.g., a related manufacturing error or wear defect) but originates from a (highly) different domain (e.g., different product, material, or appearance) (= 2nd dataset) is utilized. The approach learns the classification features from the source domain dataset while at the same time learning the differences between the source and the target domain in a single training step, aiming to transfer the relevant features to the target domain. The classifier becomes sensitive to the classification features and – by architecture – robust against the highly domain-specific context. The approach is benchmarked in a technical and a non-technical domain and shows convincing classification results. In particular, it is shown that the domain generalization capabilities and classification results are improved by the proposed architecture, allowing for larger domain shifts between source and target domains.

Schizoaffective disorder and its classification have always been a topic of discrepancy among researchers. The overlapping presentations of schizoaffective disorder, schizophrenia and psychotic bipolar disorder makes it difficult to classify and diagnose. This study is a narrative review of literatures and genetic and epidemiological research evidences, done to determine the similarities and differences between schizoaffective and psychotic bipolar disorder. Beginning from the introduction of schizoaffective disorder as "schizoaffective psychosis" by Kasanin in 1933, various researchers have proposed different views regarding the diagnosis and classifications for schizoaffective disorder. DSM-III considered schizoaffective disorder as a diagnosis of exclusion as it fails to fit the definite diagnostic criteria of schizophrenia, major affective disorders, or schizophreniform disorder. DSM-V updated the criteria of schizoaffective disorder and stated it as a life time illness rather than being an episodic disorder as in DSM-IV and hence is more reliable. However, some studies show that schizoaffective disorder patients are more like schizophrenia than mood disorder. It still remains unclear whether schizoaffective disorder is a heterogenous disease, a form of schizophrenia, a form of mood disorder or a midpoint in the continuation spectrum of schizophrenia and psychotic bipolar disease.

3D object detection is essential for an accurate and reliable autonomous driving system. Currently, the methods used by the state-of-the-art two-stage detectors are not flexible enough and their fea-ture extraction capabilities are very limited to cope effectively with the disorder and irregularity of point clouds. In this paper, we combine the advantages of both PV-RCNN and PAConv (Position Adaptive Convolution) to create a completely new network, FANet, in order to overcome the ir-regularity and disorder of point clouds. The convolution in our network builds convolutional ker-nels from a basic weight matrix, whose combined coefficients are learned adaptively by LearnNet from relative points. This network allows for flexible modeling of complex spatial variations and geometric structures in the 3D point cloud, enabling better extraction of point cloud features and producing high-quality 3D proposal boxes. Compared to other methods, FANet is superior in terms of 3D object detection accuracy. Extensive experiments on the KITTI dataset have shown a signif-icant improvement in our approach.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

Vienna Atomic Line Database (VALD) contains data on atomic and molecular energy levels and parameters of spectral lines required for stellar spectra analysis. Hundreds of millions lines for fine spectral synthesis and for opacity calculations are collected in present version of VALD (VALD3). Critical evaluation of the data and the diversity of extraction tools support high popularity of VALD among users. The data model of VALD3 incorporates obligatory links to the bibliography making our database more attractive as publishing platform for data producers. The VALD data quality and completeness are constantly improving allowing better reproduction of stellar spectra. To illustrate continuous evolution of the data content we present a comparative analysis of the recent experimental and theoretical atomic data for Fe-group elements, which will be included in the next VALD release. This release will also include a possibility for extracting the line data with full isotopic and hyperfine structures.

The late universe contains a wealth of information about fundamental physics and gravity, wrapped up in non-Gaussian fields. To make use of as much information as possible it is necessary to go beyond two-point statistics. Rather than going to higher order N-point correlation functions, we demonstrate that the probability distribution function (PDF) of spheres in the matter field (a one-point function) already contains a significant amount of this non-Gaussian information. The matter PDF dissects different density environments which are lumped together in two-point statistics, making it particularly useful for probing modifications of gravity or expansion history. Our approach in Cataneo et. al. 2021 extends the success of Large Deviation Theory for predicting the matter PDF in ΛCDM in these “extended” cosmologies. A Fisher forecast demonstrates the information content in the matter PDF via constraints for a Euclid-like survey volume combining the 3D matter PDF with the 3D matter power spectrum. Adding the matter PDF halves the uncertainties on parameters in an evolving dark energy model, relative to the power spectrum alone. Additionally, the matter PDF contains enough non-linear information to substantially increase the detection significance of departures from General Relativity, with improvements up to six times the power spectrum alone. This analysis demonstrates that the matter PDF is a promising non-Gaussian statistic for extracting cosmological information, particularly for beyond ΛCDM models.

Current commitments by European governments seek to improve energy consumption as a means to reduce carbon emissions from building stock by 2050. Within such context, retrieving reliable three-dimensional contours from point clouds becomes an important step in developing facade retrofitting solutions since facade retrofitting projects often make use of as-built 3D models to help reduce inaccuracies by narrowing interpretation and measurement errors. This work aims to provide a method that uses topology-based parametric modelling for reconstructing building envelopes from point clouds. Through a semi-automated process that gives permanent visual feedback, the user adjusts parameters to custom standards of acceptability. A solution under the form of a Grasshopper definition delivers building envelope 3D contours in various file formats as a means for increasing interoperability. The main contributions of this work consist of a parametric reconstruction workflow capable of solving building topology for retrieving 3D contours, a strategy to bypass point cloud occlusion, and a strategy for converting those contours into an IFC model directly from the parametric modelling environment.

In this paper, we present a relapse based demonstrating way to deal with investigate various arrangement MTC information. A commonplace use of this displaying approach incorporates three stages: first, define a model that approximates the connection between quality articulation and trial factors, with boundaries consolidated to address the exploration premium; second, utilize least-squares and assessing condition methods to gauge boundaries and their relating standard blunders; third, register test insights, P-qualities and NFD as proportions of factual criticalness. The benefits of this methodology are as per the following. To begin with, it tends to the exploration interest in a particular, precise way, and maximally uses all the information and other important data. Second, it represents both orderly and irregular varieties related with the information, and the consequences of such examination give not just quality explicit data applicable to the exploration objective, yet additionally its dependability, in this way helping agents to settle on better choices for subsequent investigations. Third, this methodology is truly adaptable, and can undoubtedly be stretched out to different sorts of MTC considers or other microarray explores by detailing various models dependent on the test plan of the investigations.

Non-destructive testing of metallic objects that may contain embedded defects of different sizes is an important application in many industrial branches for quality control. Most of these techniques allow defect detection and its approximate localization, but very few give enough information for its 3D reconstruction. Here we present a hybrid laser – transducer system that combines remote laser-generated ultrasound excitation and non-contact ultrasonic transducer detection. This fully non-contact method gives access to separating scan areas on different object’s faces and defect details from different angles/perspectives can be analysed. This hybrid system can analyse the whole object’s volume data and allow a 3D reconstruction image of the embedded defects. As a novelty for the signal processing improvement, we use a 2D apodization window filtering technique, applied along with the synthetic aperture focusing algorithm in order to remove the undesired effects of side lobes and wide-angle reflections of propagating ultrasound waves, thus, enhancing the resulting 3D image of the defect. We provide both qualitative and quantitative volumetric results with high accuracy and resolution compared with conventional techniques.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

Large volume bone defect regeneration is complex and demands time to complete. Several regeneration phases with unique characteristics including immune responses follow, overlap, and interdepend on each other and, if successful, lead to the regeneration of the organ bone's form and function. However, during traumatic, infectious, or neoplastic clinical cases, the intrinsic bone regeneration capacity may exceed, and surgical intervention is indicated. Scaffold-guided bone regeneration (SGBR) has recently shown efficacy in preclinical and clinical studies. To investigate different SGBR strategies over periods of up to 3 years we have established a well characterized large segmental tibial bone defect ovine model, for which we have developed and optimized immunohistochemistry (IHC) protocols. We present an overview of the immunohistochemical characterization of different experimental groups in which all ovine segmental defects were treated with a bone grafting technique combined with a three-dimensionally printed medical-grade polycaprolactone-tricalcium phosphate (mPCL-TCP) scaffold. The qualitative data set is based on osteoimmunological findings gained from IHC analyses of over >350 sheep surgeries over the past two decades. Our systematic and standardized IHC protocols enabled us to gain further insight into the complex and long-drawn-out bone regeneration processes, which ultimately proved to be a critical element for successful translational research.

Objective: Regeneration of bone defects remains a challenge for maxillofacial and reparative surgeons. The purpose of this histological study was to assess the osteogenic potential of octacalcium phosphate (OCP) and bone matrix gelatin (BMG) alone and in combination in artificially created mandibular bone defects in rats. The quality of the newly formed bone was also evaluated. Methods: Thirty-six male Sprague Dawley rats (6-8 weeks old with 120-150 g weight) were randomly divided into four groups. Defects (3 mm in diameter and 2 mm in depth) were created in the mandible of rats and filled with 6 mg of OCP, BMG or a combination of both (1/4 ratio), respectively. Defects were left unfilled in the control group. To assess osteoinduction and bone regeneration and determine the quality of the newly formed bone, tissue specimens were harvested at seven, 14, and 21 days post-implantation. The specimens were processed, stained with hematoxylin and eosin (H&E) and histologically analyzed under light microscopy. Results: In the experimental groups, new bone formation was initiated at the margins of defects from seventh day after implantation. At the end of the study period, the amount of the newly formed bone increased and the bone was relatively mature. Osteoinduction and new bone formation were greater in OCP/BMG group. In the control group, slight amount of new bone had been formed at the defect margins (next to host bone) on day 21. Conclusion: Combination of OCP/BMG may serve as an optimal biomaterial for treatment of mandibular bone defects.

Coastal cliffs erode in response to short- and long-term environmental changes but predicting these changes continues to be a challenge. In addition to a chronic lack of data on the cliff face, vegetation presence and growth can bias our erosion measurements and limit our ability to detect geomorphic erosion by obscuring the cliff face. This paper builds on past research segmenting vegetation in 3-band red, green, blue (RGB) imagery and presents two approaches to segmenting and filtering vegetation from the bare cliff face in dense point clouds constructed from RGB images and structure-from-motion (SfM) software. Vegetation indices were computed from previously published research and their utility in segmenting vegetation from bare cliff face were compared against machine learning (ML) models for point cloud segmentation. Results demonstrate that, while existing vegetation indices and ML models are both capable of segmenting vegetation and bare cliff face sediments, ML models can be more efficient and robust across different growing seasons. ML model accuracy quickly reached an asymptote with only two layers and RGB images only (i.e., no vegetation indices), suggesting that these more parsimonious models may be more robust to a range of environmental conditions than existing vegetation indices which vary substantially from one growing season to another with changes in vegetation phenology.

This paper introduces a method for tunnel point cloud and BIM model integration and cross-section monitoring, providing information to analyse tunnel cross-sections and surrounding rock deformation, and support for tunnel maintenance and reconstruction. Three types of data are processed for the integration: laser scanning point cloud, BIM tunnel model and terrain model from oblique photogrammetry. An adaptive BIM modelling scheme is proposed for tunnels with alien structures. Precise spatial registration of the data sets is conducted by applying singular value decomposition (SVD) algorithm to calculate transformation parameters from the point cloud model to the BIM model. Since the tunnel central line has high-order derivability, a cross-section calculation method based on tangent vector is proposed to obtain the cross-sectional profile of tunnels at any mileage. The proposed method has been verified by applying it to a tunnel reconstruction project. The experiment results show that the tunnel point cloud and the BIM model were highly coincident after the integration. The developed program can effectively get the cross-section of the tunnel at any mileage, and correctly express the spatial relationship between the BIM tunnel, the point cloud of tunnel and the external mountainous terrain.

A 68-year-old man with malignant metastatic melanoma in complete remission after Pembrolizumab treatment, developed 10 months after Pembrolizumab cessation due a grade 3 diarrhea, confusion, altered mental status, progressive memory loss, gait disturbance. He was admitted to the neurologic department and comprehensive neurological workup, brain magnetic resonance imaging, cerebral fluid analysis, EEG, blood test allowed the diagnosis of autoimmune encephalitis. The patient was treated with plasmapheresis, high dose of intravenous steroids and intravenous immunoglobulins. The patient improved and he is now well with a performance status 1. This case is interesting since the AE developed approximately 10 months after the cessation of immunotherapy, the underlying cancer was in complete remission and the AE showed a good response to the treatment done.

This study aims to theoretically address the design and analysis of an efficient pressure sensor designed by using a polymer-based defective 1D annular photonic crystal (APC). The 1D APC comprises an alternate arrangement of Si and SiO2 in a cylindrical fashion, incorporating a central defect layer. The investigation of the reflectance characteristics of the proposed structure is conducted by separately considering the polystyrene (PS) and the polymethyl methacrylate (PMMA) polymer materials as the defect layer. The pressure-sensitive refractive index of the polymers and the constituent materials of the APC plays a vital role in envisaging the pressure-sensing application. The cornerstone of this study is represented by the shift analysis in the wavelength of the defect mode inside the band gap using different applied pressures by employing the modified transfer matrix method (MTMM). Various geometrical parameters like the defect polymer layer’s thickness and the APC period were carefully optimized to achieve higher sensing performance. The proposed design demonstrated a remarkable pressure sensitivity and FoM of 51.29 nm/GPa and 301.7 GPa-1, respectively, which is considerably high in the current research scenario. It is believed that the proposed structure can be an apt candidate as an innovative high-performance pressure sensor, and it can play a key role in photonic integrated circuits.

The notion of Critical Point Theory has extensive application in the filed of Partial Differential Equations, one of which is studying the existence and commenting on the uniqueness and multiplicity (in case when the solution is not unique) of weak solutions to Elliptic PDEs under certain boundary conditions.\par This article provides a brief survey about specific concepts like : differentiation on Banach Spaces, maxima and minima and its applications to PDEs. Furthermore, we've discussed the notion of defining a weak topology on Banach Spaces, before introducing the Variational Principle and its applications.\par The epilogue of the article primarily deals with results which studies the existence of weak solutions to Dirichlet Boundary Value Problems under specific conditions. The most notable aspect of this article is the proof of \textit{Rabinowitz's Saddle Point Theorem} using the method of \textit{Brouwer Degree}. Readers who are highly motivated in pursuing research in any of the topics relevent to the contents of this paper will surely find the \texttt{References} section to be extremely resourceful.

The notion of oriented set is the basic elementary concept of the theory of changeable sets. The main motivation for the introduction of changeable sets was the sixth Hilbert problem, that is, the problem of mathematically rigorous formulation of the fundamentals of theoretical physics. In the present paper the necessary and sufficient condition of the existence of one-point time on an oriented set is established. From the intuitive point of view, one-point time is the time associated with the evolution of a system consisting of only one object (for example, from one material point). Namely, it is proven that the one-point time exists on the oriented set if and only if this oriented set is a quasi-chain. Also, using the obtained result, the problem of describing all possible images of linearly ordered sets is solved. This problem naturally arises in the theory of ordered sets.

This work condenses various modeling techniques for different Point Absorber configurations. A combined frequency - time domain model will be developed in Matlab-FORTRAN in order to compute the displacement, velocities and the power absorbed in the heave mode. Additionally, a single buoy motion including multiple degrees of freedom will be investigated as well. Therefore, the diffraction-radiation Boundary Element Method solvers NEMOH and BEMIO will be applied in the calculation of the hydrodynamic coefficients, which will determine the solution of Newtons impulse equations of motion. Initially, the Wave to wire model will be validated through comparison with previous experimental results for a submerged cone cylinder shape (Buldra-FO3). A single, generic, vertical floating cylinder will be contemplated then, that responds to the action of the passing waves excitation. Later, two vertical floating cylinders aligned with the incident wave direction will be modeled for a variable distance between the bodies. For both unidirectional regular and irregular waves as an input in deep water, the convolutive radiation force function term will be hereby approximated through the Prony method. By changing the spatial disposition of the axisymmetric buoys, using for instance triangular or diamond shaped arrays of three and four bodies respectively, the study will focus on the interaction effects for regular waves. The results will highlight the most efficient layout for maximizing the energy production whilst providing important insights into their performance, revealing for instance displacement amplification or capture width ratios in near-resonance conditions.

Measuring bias is important as it helps identify flaws in quantitative forecasting methods or judgmental forecasts. It can, therefore, potentially help improve forecasts. Despite this, bias tends to be under-represented in the literature: many studies focus solely on measuring accuracy. Methods for assessing bias in single series are relatively well-known and well-researched, but for datasets containing thousands of observations for multiple series, the methodology for measuring and reporting bias is less obvious. We compare alternative approaches against a number of criteria when rolling-origin point forecasts are available for different forecasting methods and for multiple horizons over multiple series. We focus on relatively simple, yet interpretable and easy-to-implement metrics and visualization tools that are likely to be applicable in practice. To study the statistical properties of alternative measures we use theoretical concepts and simulation experiments based on artificial data with predetermined features. We describe the difference between mean and median bias, describe the connection between metrics for accuracy and bias, provide suitable bias measures depending on the loss function used to optimise forecasts, and suggest which measures for accuracy should be used to accompany bias indicators. We propose several new measures and provide our recommendations on how to evaluate forecast bias across multiple series.

In this paper, we prove some common fi xed point theorems on complex partial metric space. The presented results gener- alize and expand some of the literature well-known results. We also explore some of the application of our key results.

This paper presents the validation of the End Point Rate (EPR) tool for QGIS (EPR4Q), a tool built-in QGIS Graphical Modeler to calculate the shoreline change by End Point Rate method. The EPR4Q tries to fill the gap of user-friendly and free open-source tool for shoreline analysis in Geographic Information System environment, since the most used software - Digital Shoreline Analysis System (DSAS) - although is a free extension, is suited for commercial software. Besides, the best free open-source option to calculate EPR called Analyzing Moving Boundaries Using R (AMBUR), since it is a robust and powerful tool, the complexity and heavy processes can restrict the accessibility and simple usage. The validation methodology consists of applying the EPR4Q, DSAS, and AMBUR on different examples of shorelines found in nature, extracted from the U.S. Geological Survey Open-File. The obtained results of each tool were compared with Pearson correlation coefficient. The validation results indicate that the EPR4Q tool created acquired high correlation values with DSAS and AMBUR, reaching a coefficient of 0.98 to 1.00 on linear, extensive, and non-extensive shorelines, guarantying that the EPR4Q tool is ready to be freely used by the academic, scientific, engineering, and coastal managers communities worldwide.

Technological defects in the organoleptic characteristics of cheese (odour, colour, texture and flavour) reduce quality and consumer acceptance. A red colour defect in Cabrales cheese (a traditional, blue-veined, Spanish cheese made from raw milk) occurs infrequently but can have a notable economic impact on family-owned, artisanal cheesemaking businesses. This work reports the culture-based determination of Serratia marcescens strain R01 as the microbe involved in the appearance of red spots on the surface and nearby inner areas of such cheese. Sequencing and analysis of its genome revealed a cluster of 16 genes involved in the production of prodigiosin, a tripyrrole red pigment. HPLC analysis confirmed the presence of prodigiosin in methanol extracts of S. marcescens RO1 cultures. The same was also observed in extracts from red areas of affected cheeses. The strain showed low survival rates under acidic conditions, but was not affected by concentrations of up to 5% NaCl (the usual value for blue cheese). The optimal conditions for prodigiosin production by S. marscescens RO1 on agar plates were 32 ºC and aerobic conditions. Prodigiosin has been reported to possess antimicrobial activity, which agrees with the here-observed inhibitory effect of RO1 supernatants on different bacteria, its inhibition of Enterobacteriaceae, and the delayed development of Penicillium roqueforti during cheesemaking. The association between S. marcescens and the red colour defect was strengthened by recreating the fault in experimental cheeses inoculated with RO1. The data gathered in this study points towards the starting milk to be the origin of this bacterium in cheese. These findings should help in the development of strategies that minimize the incidence of pigmenting S. marcescens in milk, the red defect the bacterium causes in cheese, and its associated economic losses.

Software is playing the most important role in recent vehicle innovation, and consequently the amount of software has been rapidly growing last decades. Safety-critical nature of ships, one sort of vehicles, makes Software Quality Assurance (SQA) has gotten to be a fundamental prerequisite. Just-In-Time Software Defect Prediction (JIT-SDP) aims to conduct software defect prediction (SDP) on commit-level code changes to achieve effective SQA resource allocation. The first case study of SDP in maritime domain reported feasible prediction performance. However, we still consider that the prediction model has still rooms for improvement since the parameters of the model are not optimized yet. Harmony Search (HS) is a widely used music-inspired meta-heuristic optimization algorithm. In this article, we demonstrated that JIT-SDP can produce the better performance of prediction by applying HS-based parameter optimization with balanced fitness value. Using two real-world datasets from the maritime software project, we obtained an optimized model that meets the performance criterion beyond baseline of previous case study throughout various defect to non-defect class imbalance ratio of datasets. Experiments with open source software also showed better recall for all datasets despite we considered balance as performance index. HS-based parameter optimized JIT-SDP can be applied to the maritime domain software with high class imbalance ratio. Finally, we expect that our research can be extended to improve performance of JIT-SDP not only in maritime domain software but also in open source software.

High-Level Synthesis (HLS) tools have revolutionized FPGA application development by providing a more efficient and streamlined approach, significantly impacting digital design methodologies. Despite the capability of FPGAs to customize numerical representations in data paths, most HLS projects have focused on fixed-point precision, while floating-point representations remain limited to vendor-provided single, double, and half-precision formats. This paper proposes a customized floating-point library compatible with HLS to address these limitations. This library allows programmers to define the number of exponent and mantissa bits at compile time, providing greater flexibility and enabling the use of mixed precision. Moreover, this library includes optimized implementations of common components such as vector summation (VSUM), dot-product (DP), and matrix-vector multiplication (MVM). Results demonstrate that the proposed library reduces latency and resource utilization compared to vendor IP blocks, particularly in VSUM, DP, and MVM operations. For example, the MVM operation involving a 32x32 matrix, using vendor IP requires 22 clock cycles, whereas CuFP completes the same task in just 7 clock cycles, using approximately 60% fewer DSPs, 10% fewer LUTs, and 60% fewer FFs.

In this short communication, following a brief introduction, we undertake a comprehensive analytical study of the weighted Simpson index. Our primary emphasis concerns the precise determination of the optimal point (minimizer) coordinates and of the minimum value of the index, a differentiable convex function, which is related to the harmonic mean concept. Furthermore, we address and solve the inversion problem and show the tight connection between both approaches. Last, we give some insights and final remarks on this subject.

While the language model using the stop sign as an independent token has been widely used to decide when the model should stop, it may lead to the growth of vocabulary dimensions and further problems. Similarly, present research on game algorithms usually estimate stopping point related problems based on the evaluation of the winning rate. However, information redundancy may also exist in such models, thus increasing the training difficulty. Above two types of tasks (and similar autoregressive tasks) show a common problem of stopping point prediction. In this paper, we describe a design of separated model, trying to separate the complexity of stopping point prediction from the main task model, so that the information used for estimating stopping point can be reduced. On this basis, in order to verify the rationality of using separated model, we propose a model-free test method. It judges the separability of transformed data based on point difference and sequence difference metrics. In this way, it can predict the credibility of the separated model inference.

Most real-time terrain point cloud rendering techniques do not address the empty space between the points but rather try to minimize it by changing the way how the points are rendered by either rendering them bigger or with more appropriate shapes such as paraboloids. In this work, we propose an alternative approach to point cloud rendering, which addresses the empty space between the points and tries to fill it with appropriate values to achieve the best possible output. The proposed approach runs in real time and outperforms several existing point cloud rendering techniques in terms of speed and render quality.

In this note we describe a new approach to the option pricing problem by introducing the notion of the safe (and acceptable) for the writer price of an option, in contrast to the fair price used in the Black-Scholes model. Our starting point is that the option pricing problem is closely related with the hedging problem by practical techniques. Recalling that the Black - Scholes model does not give us the price of the option but the initial value of a replicating portfolio we observe easily that has a serious disadvantage because assumes the building of this replicating portfolio continuously in time and this is a disadvantage of any model that assumes such a construction. Here we study the problem from the practical point of view concerning mainly the over the counter market. This approach is not affected by the number of the underlying assets and is particularly useful for incomplete markets. In the usual Black-Scholes or binomial or some other approaches one assumes that one can invest or borrow at the same risk free rate $r>0$ which is not true in general. Even if this is the case one can immediately observes that this risk free rate is not a universal constant but is different among different people or institutions. So, the fair price of an option is not so much fair! Moreover, the two sides are not, in general, equivalent against the risk therefore the notion of a fair price has no meaning at all. We also define a variant of the usual binomial model, by estimating safe upward and downward rates $u,d$, trying to give a cheaper safe or acceptable price for the option.

The article presents the Base Point Split (BPSplit) algorithm for generating a polygon skeleton based on sets of vector data describing lakes and rivers. A key feature of the BPSplit algorithm is that it is dependent on base points representing the source or mouth of a river or a stream. The input values of base points determine the shape of the resulting skeleton. Various skeletons can be generated with the use of different base points. Base points are applied to divide polygon boundaries into segments. Segmentation supports the selection of TIN edges inside polygons. The midpoints of selected TIN edges constitute a basis for generating a skeleton. The algorithm handles polygons with numerous holes, and it accounts for all holes. This article proposes a method for modifying a complex skeleton with numerous holes. In the discussed approach, skeleton edges that do not meet the preset criteria (e.g. that the skeleton is to be located between holes in the center of the polygon), are automatically removed. A simple algorithm for smoothing zigzag lines was proposed.

This paper presents a unified reconfigurable coordinate rotation digital computer (CORDIC) processor for floating-point arithmetic. It can be configured to operate in multi-mode to achieve a variety of operations and replaces multiple single-mode CORDIC processors. A reconfigurable pipeline-parallel mixed architecture is proposed to adapt different operations, which maximizes the sharing of common hardware circuit and achieves the area-delay-efficiency. Compared with previous unified floating-point CORDIC processors, the consumption of hardware resources is greatly reduced. As a proof of concept, we apply it to 1638416384 points target Synthetic Aperture Radar (SAR) imaging system, which is implemented on Xilinx XC7VX690T FPGA platform. The maximum relative error of each phase function between hardware and software computation and the corresponding SAR imaging result can meet the accuracy index requirements.

Nowadays, the most advanced micromachined microphones on the market are based on a capacitive coupling principle. Capacitive micro-electro-mechanical systems-based (MEMS) microphones resemble their millimetric counterparts, both in function and in performances. The most advanced MEMS microphones reached a competitive level compared to commonly used measuring microphones in most of the key performance parameters except the acoustic overload point (AOP). In an effort to find a solution for measurement of high-level acoustic fields, microphones with piezoelectric coupling principle have been proposed. Such novel microphones exploit the piezoelectric effect of a thin layer of aluminum nitride, which is incorporated in their diaphragm structure. In these microphones fabricated with micromachining technology, no fixed electrode is necessary, in contrast to capacitive microphones. This specificity significantly simplifies both the design and the fabrication and opens the door for a new improvement of the acoustic overload point as well as harsh environmental applications. Several variations of piezoelectric structures together with an idea leading to electrically controlled sensitivity of MEMS piezoelectric microphone are discussed in the paper.

In recent years, there has been significant growth in the ubiquity and popularity of three dimensional(3D) point clouds, with an increasing focus on the classification of 3D point clouds. To extract richer features from point clouds, many researchers have turned their attention to various point set regions and channels within irregular point clouds. However, this approach has limited capability in attending to crucial regions of interest in 3D point clouds and may overlook valuable information from neighboring features during feature aggregation. Therefore, this paper proposes a novel 3D point cloud classification method based on global attention and adaptive graph convolution. The method consists of two main branches: the first branch com-putes attention masks for each point, while the second branch employs adaptive graph convolu-tion to extract global features from the point set. It dynamically learns features based on point interactions, generating adaptive kernels to effectively and precisely capture diverse relationships among points from different semantic parts. Experimental results demonstrate that the proposed model achieves 93.8% in overall accuracy and 90.8% in average accuracy on the ModeNet40 dataset.

We measured the anelastic, dielectric and structural properties of the metal-free molecular perovskite (ABX$_{3}$) (MDABCO)(NH$_{4}$)I$_{3}$, which has already been demonstrated to become ferroelectric below $T_{\text{C}}=$ 448~K. Both the dielectric permittivity measured in air on discs pressed from powder and the complex Young's modulus measured on resonating bars in vacuum show that the material starts deteriorating with loss of mass just above $T_{\text{C}}$, introducing defects and markedly lowering $T_{\text{C}}$. The elastic modulus softens of 50\% when heating through the initial $T_{\mathrm{C}}$, contrary to usual ferroelectrics, which are stiffer in the paraelectric phase. This suggests improper ferroelectricity, where the primary order parameter of the transition is not the electric polarization, but the orientational order of the MDABCO molecules. The degraded material presents thermally activated relaxation peaks in the elastic energy loss, whose intensities increase together with the decrease of ~$T_{\mathrm{C}}$. The peaks are much broader than pure Debye, due to the general loss of crystallinity, also apparent from X-ray diffraction, but their relaxation times have parameters typical of point defects. It is argued that the major defects should be of the Schottky type, mainly due to the loss of (MDABCO)$^{2+} $ and I$^{-}$, leaving charge neutrality, and possibly also (NH$_{4}$)$^{+}$ vacancies. The focus is on an anelastic relaxation process peaked around 200~K at $\sim 1$~kHz, whose relaxation time follows the Arrhenius law with $\tau $$_{0}$~$\sim $\ $10^{-13}$\ s and $E\simeq 0.4$~eV. This peak is attributed to I vacancies (V$_{\text{X}}$) hopping around MDABCO vacancies (V$_{\text{A}}$) and its intensity presents a peculiar dependence on temperature and content of defects. The phenomenology is thoroughly discussed in terms of lattice disorder introduced by defects and of partition of V$_{\text{X}}$ among sites that are far from and close to the cation vacancies. A method is proposed for calculating the relative concentrations of V$_{\text{X}}$, that are untrapped, paired with V$_{\text{A}}$ or forming V$_{\text{X}}$--V$_{\text{A}}$--V$_{\text{X}}$ complexes.

This paper provides a new management method (MM) to optimally operate standalone direct current (DC) photovoltaic water pumping system (PVWPS) and synchronize its hydraulic performance to variable daily irradiance. The proposed approach well considers the issues from PV generator and a positive displacement pump mismatching to deserve a hydraulic network. Accordingly, Management Method uses small pumps mounted in parallel scheme to displace the hydraulic power point (HPP) in order to satisfy the mal adequacy between supply and load. Based on experimental Study; this approach showed a yielded standalone system, possibility of running pumping system using only photovoltaic supply (Without use of capacitance), and possibility to design more economical PV systems as the maximum peak power demand for each month can be satisfied using small power pumps in parallel and adjusting their switch with accordance to varying daily irradiance. Moreover, an analytical model was developed with reference to the obtained experimental results. This model based on a daily occurring irradiance as inputs in order to predict optimal performance outputs. It can be considered as a decision tool to track power point resulting from optimal electrical and hydraulic performances of the pumping system according to changes of the daily irradiance.

The nature of the fracture and fragmentation process of concrete medium under blast loading is the transformation process of the medium from continuum to discontinuity, coupled with the significant rate correlation of concrete medium, its mechanical behavior presents a high degree of complexity. Problems such as grid distortion and even negative volume are often encountered in the finite element method and others when solving this problem, while the material point method can effectively avoid these problems. In addition, the widely used HJC concrete constitutive model does not take into account the segmented characteristics of the calculation function for dynamic increasing factor. Therefore, in this paper, firstly, the calculation function for dynamic increasing factor in the HJC concrete model is modified by SHPB experiment, and the improved HJC concrete model is proposed; secondly, the material point method simulation program is developed, and the improved HJC concrete model is embedded into the simulation program; finally, the simulation program is verified by numerical examples, and the results show that the developed simulation program can better simulate the fracture and fragmentation process of concrete medium under blast loading, especially the pulverization characteristics of the medium in the near zone of the load.

Biosensors have shown great potential in realizing rapid, low cost and portable on-site detection for diseases. This work reports the development of a new bioelectronic sensor called AC electrokinetics-based capacitive (ABC) biosensor, for the detection of genomic DNA (gDNA) of methicillin-resistant Staphylococcus aureus (MRSA). The ABC sensor is based on interdigitated microelectrodes biofunctionalized with oligonucleotide probes. It uses a special AC signal for direct capacitive monitoring of topological change on nanostructured sensor surface, which simultaneously induce dieletrophoretic enrichment of target gDNAs. As a result, rapid and specific detection of gDNA/probe hybridization can be realized with high sensitivity. It requires no signal amplification such as labelling, hybridization chain reaction, or nucleic acid sequence-based amplification. This method involves only simple sample preparation. After optimization of nano-structured sensor surface and signal processing, the ABC sensor demonstrated fast turnaround of results (~10 s detection), excellent sensitivity (a detection limit of 4.7 DNA copies /µL MRSA gDNA) and high specificity, suitable for point of care diagnosis. As a bioelectronic sensor, the developed ABC sensors can be easily adapted for detection of other infectious agents.

Empirically based modeling is an essential aspect of design for a wave energy converter. These models are used in structural, mechanical and control design processes, as well as for performance prediction. The design of experiments and methods used to produce models from collected data have a strong impact on the quality of the model. This study considers the system identification and model validation process based on data collected from a wave tank test of a model-scale wave energy converter. Experimental design and data processing techniques based on general system identification procedures are discussed and compared with the practices often followed for wave tank testing. The general system identification processes are shown to have a number of advantages. The experimental data is then used to produce multiple models for the dynamics of the device. These models are validated and their performance is compared against one and other. While most models of wave energy converters use a formulation with wave elevation as an input, this study shows that a model using a hull pressure sensor to incorporate the wave excitation phenomenon has better accuracy.

Software stands as one of the most rapidly evolving technologies in the present era, characterized by its swift expansion in both scale and complexity which leads to challenges in quality assurance. Software Defect Prediction (SDP) emerges as a methodology crafted to anticipate undiscovered defects, leveraging known defect data from existing codes. This methodology serves to facilitate software quality management, thereby ensuring overall product quality. Machine Learning (ML) and Deep Learning (DL) methodologies exhibit superior accuracy and adaptability compared to traditional statistical approaches catalyzing active researches in this domain. However, it makes us hard to generalize not only because of the disparity between open-source project and commercial project but also the difference on each industrial sectors. Consequently, further research utilizing datasets sourced from diverse real-world sectors becomes imperative to bolster the applicability of these findings. In this study, we utilized embedded software for telecommunication systems of SAMSUNG ELECTRONICS, supplemented by the introduction of nine novel features to train the model, and subsequent analysis of results ensued. Experimental outcomes revealed that the F-measurement metric has been enhanced from 0.58 to 0.63 upon integration of the new features, thereby signifying a performance augmentation of 8.62%. This case study is anticipated to contribute to bolster the application of SDP methodologies within analogous industrial sectors.

The purpose of this work was to achieve non-destructive detection of the internal defects of in-shell walnuts using X-ray radiography technology based on improved Faster R-CNN network model. First, the FPN structure was added to the feature extraction layer to extract richer image information. Then ROI Align was used to instead of ROI Pooling for eliminating the localization bias problem caused by quantization operation. Finally, the Softer-NMS module was introduced to the final regression layer with the predicted bounding box for improving the localization accuracy of the candidate boxes. The results indicated that the internal defects in intact walnuts with shells could be identified effectively using the proposed improved network model in this study. Specifically, the discrimination accuracy of the in-shell sound, shriveled and empty-shell walnuts were 96.14%, 91.72% and 94.80% respectively, and the highest overall accuracy can reach 94.22 %. Contrasted with original Faster R-CNN network model, the mAP and F1-value of the improved Faster R-CNN model increased by 5.86% and 5.65%, respectively. Consequently, the proposed method can be applied for the in-shell walnuts with shriveled and empty-shell defects.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

The treatment of large-area bone defects remains a challenge; however, various strategies have been developed to improve the performances of scaffolds in bone tissue engineering. In this study, poly(lactide-co-glycolide)/hydroxyapatite (PLGA/HA) scaffold was coated with Asp-Gly-Glu-Ala (DGEA)-incorporated collagen for the repair of rat skull defect. Our results indicated that the mechanical strength and hydrophilicity of PLGA/HA scaffold were clearly improved and conducive to cell adhesion and proliferation. The collagen-coated scaffold with DGEA significantly promoted the repair of skull defect. These findings indicated that a combination of collagen coating and DGEA improved scaffold properties for bone regeneration, thereby providing a new potential strategy for scaffold design.

This study focuses on the impact of weak partial discharges (PDs) on defect recognition accuracy in epoxy resin through phase-resolved partial discharge (PRPD) analysis. Two measurement conditions are compared until PRPD pattern saturation: one-minute and one-hour durations. The PD data specifically target three void types located at different positions within the epoxy material. The aim is to evaluate how the presence of weak PDs at the PD extinction voltage (PDEV) influences defect recognition accuracy. This research sheds light on the potential implications of neglecting the significance of weak PD signals in defect detection. A convolutional neural network (CNN) model is trained using PRPD data recorded at the PD inception voltage (PDIV) and tested using the new PRPD data from both conditions recorded from a lower PDIV to a PDEV. The trained CNN model achieves a defect recognition accuracy of 100% for a one-hour duration, highlighting the importance of not neglecting weak PD signals. This emphasizes the significance of extended measurement duration and pattern saturation in capturing and analyzing weak PD signals for improved defect recognition. This study contributes to the advancement of practical applications by understanding the behavior of the epoxy material and enhancing defect detection techniques.

Clean production of renewable fuels is a great challenge of our scientific community. Iridium complexes have demonstrated a superior catalytic activity in the water oxidation (WO) reaction, which is a crucial step in water splitting process. Herein we have used a defective zirconium MOF with UiO-66 structure as support of a highly active Ir complex based on EDTA with formula [Ir(HEDTA)Cl]Na. The defects are induced by the partial substitution of tereftalic acid with smaller formiate groups. Anchoring of the complex occurs through a post-synthetic exchange of formiate anions, coordinated at the zirconium clusters of the MOF, with the free carboxylate group of the [Ir(HEDTA)Cl]-complex. The modified material was tested as heterogenous catalyst for the WO reaction by using Cerium Ammonium Nitrate as sacrificial agent. Although TOF and TON values are comparable to those of other iridium heterogenized catalysts, the MOF exhibits iridium leaching not limited at the first catalytic run, as usually observed, suggesting a lack of stability of the hybrid system under strong oxidative conditions.

Introduction: Austere environments include the wilderness and many lower-and-middle-income countries, many of these facing unrest and war. The access to advanced diagnostic equipment is often unaffordable even if available and is often liable to breakdown. This short review paper examines the options available to medical professionals to undertake clinical and point of care diagnostic testing in resource constrained environments and also illustrates the development of mobile advanced diagnostic equipment. The aim is to provide an overview of the spectrum and functionality of these devices beyond clinical acumen.

An increasing need for better agricultural practices that are sustainable to provide increased yields of crops for the ever increasing food demand to be met for the growing world population is a current necessity. It is estimated by the UN that in 2050 the world’s populace may be as much as 9.8 billion global, yet, farmers still face several obstacles, which includes soil degradation, extreme temperatures, and drought which as increasingly becoming more severe with climate changes. Plant health monitoring is a method that will help to increase awareness about plant enhancing by studying how to increase crop yields while decreasing the environmental impacts. The use of low-cost, controlled environments, soil quality, water levels, and pathogenic and pests attacks can be regularly monitored. Currently, several diagnostic technologies and portable point-of-use methods and technologies are employed for detection of diseases, although, the current available lab-based methods used for plant’s diagnostics test are inadequate for plant point-of-use monitoring. The promotion of use of these point of use methods will enable pathogen detection, poor plant growth, unsuitable environmental conditions and nutrient use efficiency allowing for immediate and timely corrective actions to ensure minimal damage to the plants with maximal yield. Increase in the use of sustainable agri practices are required for ensuring higher yields with minimal inputs and that are non-destructive to the land and the use of improved methodologies and technologies will be useful tools for achieving sustainable agriculture.

Based on the teaching material of "Robotics" course, this paper studied the automatic knowledge graph construction, including knowledge points extraction and knowledge point relation extraction. We proposed a new method of extracting the first-level, second-level, and third-level knowledge points as well as their prerequisite relations of knowledge points in the textbook. For the problem of insufficient knowledge of the pre-trained language model in the specific field, methods such as incremental pre-training and optimization of cost functions are employed to integrate subject knowledge into the pre-trained language model, thus improving its effectiveness. To overcome the problem that the traditional method of relationship extraction can not be applied directly to the extraction of teaching materials, a new scheme for knowledge point relationship extraction based on keyword relationship is proposed. The experimental data from textbooks shows that the F1 score of knowledge point extraction reaches 93%, considerably improved compared to the traditional model. Consequently, the knowledge point entity extraction and relationship extraction methods based on the pre-trained model can effectively extract structured information and facilitate the automatic construction of knowledge graphs.

We consider a new model of a branching random walk on a multidimensional lattice with continuous time and one source of particle reproduction and death, as well as an infinite number of sources in which, in addition to the walk, only absorption of particles can occur. The asymptotic behavior of the integer moments of both the total number of particles and the number of particles at a lattice point is studied depending on the relationship between the model parameters. In the case of the existence of an isolated positive eigenvalue of the evolution operator of the average number of particles, a limit theorem is obtained on the exponential growth of both the total number of particles and the number of particles at a lattice point.

Current pharmacological treatments of Fibromyalgia (FM) are merely symptom palliative, as clinical trials have so far failed to provide overall benefits without associated harms. Polypharmacy often leads to patient´s health deterioration and chronic drug use to an eventual lack of patient´s response. Emerging evidence support that physiotherapy treatments based on mechanical triggers improve FM symptoms and therefore could be used for therapeutic purposes by themselves, or in combination with current pharmacological treatments, as part of integrative medicine programs. However, a paucity of studies rigorously and systematically evaluating this possibility exists. This study uses scores from validated standardized questionnaires, algometer pressure point threshold (PPT) readings and responses from a custom self-developed questionnaire to determine the impact of a pressure-controlled manual protocol on FM hyperalgesia/allodynia, fatigue and patient´s quality of life. The results show that patient´s baseline sensitivity to pain inversely correlates with treatment response in FM. Moreover, patients presenting comorbid ME/CFS do not seem to respond to the applied therapy as those presenting FM only. Thus, pre-treatment PPTs and ME/CFS comorbidity may serve as indicators to predict patient´s response to physiotherapy programs based on mechanical triggers, as the one evaluated here. These unexpected findings grant further explorations including the study of gene expression profiles associating to patient´s treatment response in the blood collection of samples generated by this study.

This paper aims at tackling with the task of fusion feature from images and its corresponding point clouds for 3D object detection in autonomous driving scenarios basing on AVOD, an Aggregate View Object Detection network. The proposed fusion algorithms fuse features targeted from Bird’s Eye View (BEV) LIDAR point clouds and its corresponding RGB images. Differs in existing fusion methods, which are simply the adoptions of concatenation module, element-wise sum module or element-wise mean module, our proposed fusion algorithms enhance the interaction between BEV feature maps and its corresponding images feature maps by designing a novel structure, where single level feature maps and another utilizes multilevel feature maps. Experiments show that our proposed fusion algorithm produces better results on 3D mAP and AHS with less speed loss comparing to existing fusion method used on the KITTI 3D object detection benchmark.