Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

The article offers a comprehensive overview of recent breakthroughs in eco-friendly polymers and polymer composites, underscoring their pivotal role in addressing sustainability challenges across diverse industrial sectors. Despite encountering obstacles related to performance and processability, biopolymers sourced from renewable materials emerge as promising alternatives for the plastics that are currently used by human beings. Natural fillers are highlighted as a strategic avenue for crafting sustainable composites, with residual natural fillers being particularly explored. Heightened environmental concerns propel discussions on the criticality of integrating biodegradable materials with natural fillers, underlining the urgency for clear frameworks and financial incentives to support adoption of these materials. Additionally, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on the utilization of polyhydroxyalkanoate (PHA) in composite materials and its market prospects. Moreover, it emphasizes the indispensable need for ongoing research and development endeavors to address environmental challenges within the polymer sector, reflecting a mounting interest in sustainable materials across industries.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

In a previous study we could show a change of membrane morphology and gas separation performance by varying the recipe of a casting solution based on polysulfone in a determined solvent system. Although all results were very reproducible, all used solvents were harmful and not sustainable. In this study therefore, the solvents tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAc) are replaced by the more sustainable solvents 2-methyl-tetrahydrofuran (2M-THF), N-butyl pyrrolidinone (NBP) and cyclopentyl methyl ether (CPME). The gas permeation performance and for the first time morphology of the membranes before and after solvent replacement were determined and compared by single gas permeation measurements and SEM microscopy. It is shown, that THF can be replaced by 2M-THF and NBP without decreasing the gas permeation performance. With CPME replacing THF no membranes were formed. Best gas permeation results showed systems with 2M-THF as THF alternative. Permeances for the tested gases oxygen (O2), nitrogen (N2), carbon dioxide (CO2) and methane (CH4) were 2.66·10-4, 3.89·10-5, 1.53·10-3 and 4.52·10-5 mL(STP)/cm²·min·bar, respectively. permselectivities of those membranes for the gas pairs O2/N2, CO2/N2 and CO2/CH4 were 6.7, 38.3 and 34.0, respectively. When additionally replacing DMAc in the solvent system no or only porous membranes were obtained, even if the precipitation procedure was adjusted. These findings indicate that a complete replacement of the solvent system without affecting the membrane morphology or gas permeation performance is not possible. By varying the temperature of the precipitation bath an easy adjustment to mechanically stable PSU membranes is possible, if just THF was replaced by 2M-THF.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

The goal of this work was to develop the acrylonitrile-butadiene (NBR) elastomer composites filled with hydroxyapatite (HAP), which were characterized with improved cure characteristics and burning resistance. Silane, i.e., (3-aminopropyl)-triethoxysilane, ionic liquid, i.e., 1-decyl-3-methylimidazolium bromide and surfactant, i.e., cetyltrimethylammonium bromide, were used to improve the filler’s dispersibility in the elastomer matrix and to reduce the time and temperature of vulcanization. The effect of HAP and dispersants on the cure characteristics, crosslink density and physico-chemical properties of NBR composites was explored. The additives used, especially the ionic liquid and surfactant, effectively improved the dispersion of HAP in NBR matrix. The amount of HAP and the dispersant used strongly affected the cure characteristics and crosslink density of NBR. The optimal vulcanization time significantly increased with HAP content and was pronouncedly reduced when ionic liquid and surfactant were applied. In addition, ionic liquid and surfactant significantly lowered the onset vulcanization temperature, improved the crosslink density and hardness of the vulcanizates, while impairing their elasticity. HAP and dispersants did not significantly affect the damping properties and chemical resistance of NBR vulcanizates. Above all, application of HAP considerably enhanced the resistance of vulcanizates to thermo-oxidative aging and reduced their flammability compared to the unfilled NBR.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The achievement of size uniformity and monodispersity in perovskite quantum dots (QDs) requires the implementation of precise temperature control and the establishment of optimal reaction conditions. Nevertheless, the accurate control of a range of reaction variables represents a considerable challenge. This study addresses the aforementioned challenge by employing manganese (Mn) doping to achieve size uniformity in CsPbBr₃ perovskite QDs without the necessity for precise control of the reaction conditions. By optimizing the Mn:Pb ratio, it is possible to successfully dope CsPbBr₃ QDs with appropriate concentrations of Mn²⁺ and achieve a uniform size distribution. The spectroscopic measurements on single QDs indicate that the appropriate Mn²⁺ concentrations can result in a narrower spectral linewidth, a longer photoluminescence (PL) lifetime, and a reduced biexciton Auger recombination rate, thus positively affecting the PL properties. This study not only simplifies the size control of perovskite QDs, but also demonstrates the potential of Mn-doped CsPbBr₃ QDs for narrow linewidth light-emitting diode applications.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

We study theoretically the Josephson diode effect (JDE) realized in a system composed of parallel-coupled double quantum dots (DQDs) sandwiched between two semiconductor nanowires deposited on an s-wave superconductor surface. Due to the combined effects of the proximity-caused superconductivity, strong Rashba spin-orbit interaction and Zeeman splitting inside the nanowires, a pair of Majorana bound states (MBSs) may possibly emerge at opposite ends of each nanowire. Different phase factors arisen from the superconductor substrate can be generated in the coupling amplitudes between the DQDs and MBSs prepared at the left and right nanowires, and will result in the Josephson current. We find that the critical Josephson currents in positive and negative directions are different from each other in amplitude within an oscillation period with respective to the magnetic flux penetrating through the system, a phenomenon known as the JDE. It arises from the quantum interference effect in this double-path device, and can hardly occur in system of one QD coupled to MBSs. Our results also show that the diode efficiency can reach up to 50%, and depends on the overlap amplitude between the MBSs and the energy levels of the DQDs adjustable by gate voltages. The present model is realizable within current nanofabitication technologies and may find practical use in interdisciplinary field of Majorana and Josephson physics.

As an important organelle in eukaryotic cells, Golgi apparatus is responsible for processing and transporting proteins and lipids in cells. Precise monitoring the status of Golgi apparatus by targeting fluorescence imaging technology is of enormous importance but remains an attractive yet dramatically challenging task. In this study, we report the construction of the first Golgi apparatus targeted sensor with bright near-infrared fluorescence, termed as Golgi-Pdots. As a start point of our investigation, hydrophobic CDs with bright NIR fluorescence at 674 nm (fluorescence quantum yield : 12.18%), narrow emission band of 23 nm, and excellent stability were facilely prepared from Magnolia Denudata flowers through an ultrasonic method. Incorporating the CDs into a polymer matrix modified with Golgi-targeting molecules can produce the water-soluble Golgi-Pdots, which showed high colloidal stability and similar optical properties as compared to CDs. Further studies revealed that the Golgi-Pdots showed good biocompatibility and Golgi-targeting ability. Based on these fascinating properties, Golgi-Pdots have been successfully used for long term bioimaging of Golgi apparatus inside live cells.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

The present investigation highlights the synthesis of polyaniline (PANI) coated graphene oxide doped with SrTiO3 nanocube nanocomposites through facile in-situ oxidative polymerization method for the efficient removal of carcinogenic dyes, namely, the cationic dye methylene blue (MB) and the anionic dye methyl orange (MO). The synthesised nanocomposites were characterised by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adsorption efficiencies of graphene oxide (GO), PANI homopolymer and SrTiO3 nanocubes-doped nanocomposites were assessed by monitoring the adsorption of methylene blue and methyl orange dyes from aqueous solution. The adsorption efficiency of nanocomposites doped with SrTiO3 nanocubes were found to be of higher magnitude as compared with undoped nanocomposite. Moreover, the nanocomposite with 2 wt% SrTiO3 with respect to graphene oxide demonstrated excellent adsorption behaviour with 99% and 91% removal of MB and MO respectively, in a very short duration of time.

The leather industry is one of the most polluting industries in the world due to the large amounts of waste following the raw hides processing, but also due to the high content of chemicals present in their composition. The main problem of chromium-tanned leather solid waste is related to their storage, because of the ability of chromium to leach in soil or water, and also owing to the high ability of trivalent chromium to oxidize to its toxic form, hexavalent chromium. The purpose of this study is to present the latest methods for extracting trivalent chromium from the composition of solid leather wastes. The extraction methods identified in the present study are based on acid/basic/enzymatic hydrolysis and substitution with the help of organic chelators (organic acids and organic acid salts). In addition, the study includes a comparative analysis between the advantages and disadvantages of each identified extraction method. At the same time, the study also presentes alternative chromium extraction methods based on the combination of conventional extraction methods and ultrasound-assisted extraction.

The susceptible-infected-recovered-vaccinated-deceased (SIRVD) epidemic compartment model extends the SIR model to include the effects of vaccination campaigns and time-dependent fatality rates on epidemic outbreaks. It encompasses the SIR, SIRV, SIRD, and SI models as special cases, with individual time-dependent rates governing transitions between different fractions. We investigate a special class of exact solutions and accurate analytical approximations for the SIRVD and SIRD compartment models. While the SIRVD and SIRD equations pose complex integro-differential equations for the rate of new infections and the fractions as a function of time, a simpler approach considers determining equations for the sum of ratios for given variations. This approach enables us to derive fully exact analytical solutions for the SIRVD and SIRD models. For nonlinear models with a high-dimensional parameter space, such as the SIRVD and SIRD models, analytical solutions, exact or accurately approximative, are of high importance and interest: not only as suitable benchmarks for numerical codes, but especially as they allow us to understand the critical behavior of epidemic outbursts as well as the decisive role of certain parameters. In the second part of our study, we apply a recently developed analytical approximation for the SIR and SIRV models to the more general SIRVD model. This approximation offers accurate analytical expressions for epidemic quantities, such as the rate of new infections and the fraction of infected persons, particularly when the cumulative fraction of infections is small. The distinction between recovered and deceased individuals in the SIRVD model affects the calculation of the death rate, which is proportional to the infected fraction in the SIRVD/SIRD cases but often proportional to the rate of new infections in many SIR models using a posteriori approach. We demonstrate that the temporal dependence of the infected fraction and the rate of new infections differs when considering the effects of vaccinations and when the real-time dependence of fatality and recovery rates diverge. These differences are highlighted for stationary ratios and gradually decreasing fatality rates. \Revised{The case of stationary ratios allows one to construct a new powerful diagnostics method to extract analytically all SIRVD model parameters from measured COVID-19 data of a completed pandemic wave.

Context: Mental and menstrual health, two emerging aspects of health critical to the female population, are bidirectionally linked. But there is limited empirical evidence that establishes the association between these entities. This essay aims to draw the attention of researchers to this healthcare niche. Evidence Acquisition: A systematic review was carried out on literatures sourced from medical databases (e.g. PubMed, Google Scholar, Scopus, Science Direct, and Web of Science), and gray sources—popular and reputable institutional and journalistic websites that publishes mental or menstrual health research. The key words used for the search are “Menstruation, menstrual hygiene, menstrual disorders, premenstrual syndrome, period poverty, menarche, menopause, mental health, mental disorder, mental illness, depression, anxiety, phobia, mania, mood, and affect”. The initial search generated 368 results. But after the duplicates were removed, the exclusion criteria (publication before 2000) was applied, and manual review of abstract (for relevance) was done, 21 publications from the databases and 5 from gray sources were included in this essay. Results: Associations were found between menstrual cycle irregularities and disorders; and mental disorders such as premenstrual syndrome, premenstrual dysphoric disorder, major depressive disorder, major anxiety disorder, psychotic disorder, bipolar disorder, borderline personality disorder, sleep disorder, substance use/abuse, and suicidal ideation and attempts.Few positive associations between mental and menstrual health were recorded, and several research and treatment gaps were identified. Conclusion: Research into the links between mental and menstrual health should not remain a fringe area of scientific curiosity, as it shows tremendous promise in improving healthcare offered to women/girls globally.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

A key component of nanomaterials, carbon dots (CDs) are zero-dimensional solids, smaller than 10 nm in size that include carbon as their backbone structure. Herbal medicine carbon dots (HM-CDs) are nanoparticles developed from medicinal plants. Owing to their advantageous properties, they are extensively employed in biological domains such as drug administration, bio-imaging, biosensors, and DNA interactions. It's interesting to note that, carbon dots pro-duced from herbal medicines as a raw material have surfaced as the most recent addition to the CD family. This article provides an overview of the several sources of green precursor, preparation tech-niques, characterization, and applications of CDs. It reviews recent advancements in synthe-sizing CDs made from green carbon materials and their potential uses as bioimaging, catalysts and sensing. Furthermore, several difficult issues and future directions for this potent and amazing content are also covered.

Background: Parkinson's disease (PD) is a global disease. However, there is a lack of research specifically focused on the AfrAbia population. Climate change, driven mainly by global warming, is linked to detrimental health impacts, including an increased frequency and intensity of heat waves. Neurological diseases, including neurodegenerative syndromes like Alzheimer's disease, Parkinson's disease, and motor neuron illnesses, have been increasingly seen and recorded in scientific literature. Although there is much literature demonstrating the growth in neurodegenerative disorders, the relationship between environmental variables such as global warming, air pollution, heavy metals, and pesticides and the higher occurrence of these illnesses is still unknown. Objective: The current article primarily aims to examine the relationship between climatic changes, air pollution, pesticides, heavy metals, and the occurrence of PD. Initially, we evaluate the influence of exposure to these variables on the cause or origin of Parkinson's disease. In addition, we will investigate how these variables disrupt processes such as excitotoxicity, oxidative stress, and neuroinflammation, all of which are strongly linked to Parkinson's disease (PD). Conclusions: This research presents a plausible rationale for the adverse effects of environmental influences on the brain, which are pivotal in the progression or onset of Parkinson's disease from an AfrAbian standpoint.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (>70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

Composite membranes formed by sulfonated poly(ether ether ketone) (SPEEK) with embedded carbon quantum dots (CQDs) were used for detection and removal of heavy metal ions, such as lead and cadmium, from water. SPEEK is responsible for the capture of heavy metals based on the cation exchange mechanism, while CQDs detect their contamination by exhibiting changes in fluorescence. Water-insoluble “red” carbon quantum dots (rCQDs) were synthesized from p-phenylenediamine so that their photoluminescence was shifted from that of the polymer matrix. CQDs and the composites were characterized by several techniques: FTIR, Raman, UV/VIS, photoluminescence, XPS spectroscopies and AFM microscopy. The heavy metal ion concentration was analyzed by inductively coupled plasma–optical emission spectroscopy (ICP-OES). The concentration ranges were 10.8 - 0.1 mM for Pb2+ and 10.0 - 0.27 mM for Cd2+. The composite achieved 100% removal efficiency for lead and cadmium if the concentration was below a half of the ion exchange capacity of SPEEK. The regeneration of membranes in 1 M NaCl was also studied. SPEEK/rCQDs showed a turn-off effect more pronounced for lead. A second order law was effective to describe the kinetics of the process.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

As the world grapples with a pandemic with various and expanding epicenters, a flurry of medical and scientific activity has gained speed and momentum in a race to halt COVID-19. A controversial topic has been the connection between COVID-19 and the Renin-Angiotensin system (RAS). COVID-19, like Sars before it, enters by way of the Angiotensin Converting Enzyme 2 (ACE2). ACE2 is ubiquitously expressed in many tissues in the body serving as the doorway by which the virus can enter and spread causing inflammatory havoc. Demographic evidence coming out of China and other locations make it clear that the elderly and those suffering cardiovascular complications such as hypertension etc are most at risk. The connection to RAS and the demographic nature of the data coming out has led many to advance hypothesis, recommendations and even therapies based on existing RAS inhibitors and other components of the renin-Angiotensin system. It is pertinent to review the literature in the context of our understanding of the renin-angiotesnin system to allow better judgements to be made as well as lines of research initiated advancing a quick resolution to COVID-19. Covid-19 appears invincible as if dipped in the river Styx, but even Achilles had a vulnerable heel. Understanding the homeostatic balance that the coronavirus disrupts, we can discover the arrow in corona’s heel.

We present a simple strategy to generate a family of carbon dot/iron oxide nanoparticles (C/Fe-NPs) that relies on the thermal decomposition of iron (III) acetylacetonate in the presence of a highly fluorescent carbon-rich precursor, while polyethylene glycol serves as the passivation agent. By varying the molar ratio of the reactants, a series of C/Fe-NPs have been synthesized with tuneable elemental composition in terms of C, H, O, N, Fe. The quantum yield is enhanced from 6% to 9% as the carbon content increases from 27% to 36%, while the room temperature saturation magnetization is improved from 4.1 emu/g to 17.7 emu/g as the iron content is enriched from 17 to 31%. In addition, the C/Fe-NPs show excellent antimicrobial properties, minimal cytotoxicity and demonstrate promising bioimaging capabilities, thus showing great potential for the development of advanced diagnostic tools.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Novel bio-inspired materials have gained recently great attention, especially in medical applications. Applying sophisticated design and engineering methods, various polymer-polymer hybrid systems with outstanding performance have been developed in last decades. Hybrid systems composed of bioelastomers and hydrogels are very attractive due to their high biocompatibility and elastic nature for advanced biomaterials used in various medical applications such as drug delivery systems and scaffolds for tissue engineering. Herein, we describe the advances in current state-of-the-art design, properties and applications of polymer-polymer hybrid systems in medical applications. Bio-inspired functionalities, including bioadhesiveness, injectability, antibacterial properties and degradability applicable to advanced drug delivery systems and medical devices will be discussed in a context of future efforts towards development of bioinspired materials.

Hydrogels prepared from natural polymer have attracted extensive attentions in biomedical fields such as drug delivery, wound healing, and regenerative medicine due to their good biocompatibility, degradability and flexibility. This review outlines the commonly used natural polymer in hydrogel preparation, including cellulose, chitosan, collagen/gelatin, alginate, hyaluronic acid and starch. The polymeric structure and process/synthesis of natural polymers are illustrated, and natural polymer-based hydrogels including the hydrogel formation and properties are elaborated. Subsequently, the biomedical application of hydrogels based on natural polymer in drug delivery, tissue regeneration, wound healing and other biomedical field is summarized. Finally, the future perspectives of natural polymers and hydrogels based on them are discussed. For natural polymer, novel technologies such as enzymatic and biological methods are developed to improve the structural properties and the development of new natural based polymers or natural polymer derivatives with high performance is still very important and challenging. For natural polymer-based hydrogels, novel hydrogel materials, like double-network hydrogel, multifunctional composite hydrogels and hydrogel microrobots are designed to meet the advanced requirements in biomedical application, and new strategies such as dual-crosslinking, microfluidic chip, micropatterning and 3D/4D bioprinting, have been explored to fabricate advanced hydrogel materials with designed properties for biomedical application. Overall, natural polymeric hydrogels have attracted increasing interests in biomedical application, and the development of novel natural polymer-based materials and new strategies/methods for hydrogel fabrication is badly desirable and still challenging.

Carbon dots (C-dots) represent an emerging class of non-toxic nano-emitters that show excitation wavelength dependent photoluminescence (PL) with high quantum yield (QY) and minimal photobleaching. The vast majority of studies focus on C-dots that exhibit the strongest PL emission in the blue/green region of the spectrum, while longer wavelength emissions are ideal for applications such as bioimaging, photothermal and photodynamic therapy and light emitting diodes. Effective strategies to modulate the PL emission of C-dot based systems towards the red end of the spectrum rely on extensive conjugation of sp2 domains, heteroatom doping, solvatochromism, surface functionalization and passivation. Those approaches are systematically presented in this review, while emphasis is given on important applications of red-emissive suspensions, nanopowders and polymer nanocomposites.

Carbon dots are carbon based nanoparticles, which have the characteristics of simple preparation process, photoluminescence, biocompatibility, adjustable surface function, water solubility, and low toxicity. They are widely used in biological applications such as imaging, biosensing, photocatalysis, and molecular transfer. It has also aroused great interest among researchers in agriculture and has made significant progress in improving crop growth and production. This review presents the physiological functions of carbon dots for crop growth and development, photosynthesis, water and nutrient absorption, and abiotic stress resistance and their applications in improving ecological environment and agriculture as biosensors, and the future application prospects and research directions of carbon dots in agriculture were prospected.

The graphene based highly conductive and flexible devices has received momentous attraction and growth in recent years for potential multifunctional uses. The development of flexible and washable textile sensors, actuators, energy storage and energy harvesting systems. Textile fabrics coated with graphene and conductive polymers have been used for wearable self-powered e-textiles, such as tribo-electric, piezoelectric, and Thermoelectric. Herein this research, 100% woven cotton fabric is Fictionalized with graphene oxide (GO) using industrial-scale cold pad batch dyeing technique for the development of low-grade body heat into self-powered wearable e-textiles. The conductive polymer PEDOT: PSS was coated using layer by layer approach. The study demonstrates that the resultant textile electrodes showed reduced electrical sheet resistance from 2.5 MΩ to 15KΩ, with a reduced graphene oxide and further reduced to (2.5 -12.5 Ω) for conductive polymer. The sheet resistance was decreased with the number of dyeing cycles (10-15) and increased with 20 washing cycles vice versa. The study demonstrates that the sensor response and performance were improved with increasing the content percent of rGO and PEDOT: PSS. The tensile strength of as coated fabric electrodes was improved from (25.0-85.5 mPa) and fabric thickness was increased to (26-38µm) without compromising or influencing the air permeability. The resultant textile electrodes may potentially be used in smart textiles for self-powered flexible wearable generators, sensors, and energy storage. The study demonstrates that the cold pad batch dyeing method is a suitable and effective method for the fabrication of graphene-based textiles.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Nano medicine seeks to deliver a valuable set of research tools and clinically useful devices in the near future. The current medical field is in dire need of new commercial applications in the pharmaceutical industry that may include advanced drug delivery systems, new therapies, and in vivo imaging. Here in this experimental study, the nano materials used in DNA biosensors like silver nano dots were incorporated as nano biosensors are used for both therapeutic and diagnostic applications. The most important step while preparing a DNA biosensor is the immobilization of DNA probe on the surface of a sensing device such as an electrode. The amount of immobilized DNA probe will influence the accuracy sensitivity, selectivity and life of a DNA biosensor directly. Because of the high surface to volume ratio and excellent biological compatibility, nano materials can enlarge the sensing surface area to increase the amount of immobilized DNA and the DNA mixed with nano materials can keep its biologically activity well.In this study,silver nano dots created in our lab were functionalized with thio nucleides and were used as nano sensor probes in bio bar code assays.

Due to the growing interest in biopolymers, biosynthesizable and biodegradable polymers currently occupy a special place. Unfortunately, the properties of native biopolymers are not satisfactory, which explain that attempts are being made to modify them. The work attempts to improve the properties of poly(3-hydroxybutyrate) (P3HB) using linear aliphatic polyurethane (PU) based on 1,4-butanediol and hexamethylene 1,6-diisocyanate. The conducted studies on the effect of the amount of PU used (5, 10, 15 and 20 wt.%) showed an improvement in the thermal properties of the prepared polymer blends. There was an increase in the degradation temperature of the ob-tained blends in relation to the native P3HB by 12-57C, and the difference between the melting point and the degradation point was above 100°C for most of the obtained blends. As part of the tested mechanical properties of the new polymer blends, we noted the desired increase in the tensile strength, in the relative elongation at break and in the impact strength with a decrease in hardness, in particular with the presence of 5 wt.% PU. Therefore, for further improvement, hybrid nanobiocomposites with 5 wt.% PU and organically modified montmorillonite (MMT – Cloisite 30B) were produced. The nanoadditive was used in typical amount of 1-3 wt.%. The nanostructure of the biocomposites produced by extrusion was examined by small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM), the morphology by scanning electron microscopy (SEM), and compatibility by infrared spectroscopy (FT IR). In addition, selected mechanical properties were determined and thermal properties were tested by the thermogravimetric analysis (TGA) and the standard differential scanning calorimetry (DSC). The polyester and polyurethane chains penetrated into the interlayer spaces of organically modi-fied nanoclay – Cloisite30B and the complete delamination occurred during direct mixing in the extrusion process. FT IR spectral analysis showed the compatibility of the polymer biocomposite components by the coexistence of intermolecular interactions in the form of hydrogen bonds. The morphology studies of the produced hybrid nanobiocomposites showed an interaction of the bi-opolymer matrix with PU and Cloisite30B and the formation of easily migrating polyester-polyurethane-montmorillonite adducts, which resulted in improved mechanical properties com-pared to the properties of the native P3HB and P3HB-PU compositions. The influence of the presence of a nanofiller on the properties of the prepared nanobiocomposites was tested and it was found that, as expected, the smallest amount of nanofiller provides the best results.It was found that the obtained nanobiocomposites containing the smallest amount of nano-fillers, i.e. 1 wt.% Cloisite30B exhibited the best mechanical and thermal properties. The desired decrease in hardness by 15% and a higher value of impact strength by 15%, an increase in elonga-tion at break by 60% and an increase in thermal stability of the newly produced biocomposites compared to to the native P3HB were observed. The prepared nanobiocomposites combined the best features caused by the elasticizing effect of polyurethane and the formation of P3HB-PU-MMT adducts.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

The temperature-dependent intensities of the exciton (X) and biexciton (XX) peaks from single GaAs cone-shell quantum dots (QDs) are studied with micro photoluminescence (PL) at varied excitation power and QD size. The QDs are fabricated by filling of self-assembled nanoholes, which are drilled in an AlGaAs barrier by local droplet etching (LDE) during molecular beam epitaxy (MBE). This method allows the fabrication of strain-free QDs with sizes precisely controlled by the amount of material deposited for hole filling. Starting from the base temperature T = 3.2 K of the cryostat, single-dot PL measurements demonstrate a strong enhancement of the exciton emission up to a factor of five with increasing T. Both, the maximum exciton intensity and the temperature Tx,max of the maximum intensity depend on excitation power and dot size. At an elevated excitation power, Tx,max becomes larger than 30 K. This allows an operation using an inexpensive and compact Stirling cryocooler. Above Tx,max, the exciton intensity decreases strongly up to its disappearance. The experimental data are quantitatively reproduced by a model which considers the competing processes of exciton generation, annihilation, and recombination. Exciton generation in the QDs is given by the sum of direct excitation in the dot plus additional bulk excitons diffusing from the barrier layers into the dot. The thermally-driven bulk-exciton diffusion from the barriers causes the temperature enhancement of the exciton emission. Above Tx,max, the intensity decreases due to exciton annihilation processes. In comparison to the exciton, the biexciton intensity shows an only very weak enhancement, which is attributed to more efficient annihilation processes.

Talbot effect is a self-imaging or lensless imaging phenomenon of a periodic grating illuminated by a collimated light beam at regular distances from the grating. Research on the Talbot effect has recently made significant strides thanks to the quick development of optical superlattices. The emergence of various applications of this effect in fields such as optics, acoustics, X-ray, plasmonics, and information processing has led to the increasing importance of obtaining a Talbot carpet with the use of different structures. In this paper, we investigate the Talbot effect that originates from the tunneling effect between an ensemble of vertically coupled cylindrical quantum dots (QDs). The Talbot carpet can be manipulated by changing the parameters of the QD system. In the current paper, two modified Pöschl-Teller potentials were used to model the QDs ensemble. The exciton’s lifetime and tunneling time’s dependence on the first QD’s potential half-width is found for a fixed value of the external electric field. The nonlinear changes in the refractive index and absorption spectrum dependent on the tunneling effect are obtained. Afterward, the Talbot carpet formation is investigated, particularly the dependences of the formed periodic wavefront’s visibility on medium length, coupling field’s strength, and tunneling parameter. Finally, we have observed the intensity distribution of the diffraction field at Talbot half-distance.

To realize precise control of the quantum dots (Qdots) device, multi-channel precision bias source plays the key role. In this paper, the 16-channel high precision bias source with 18-bit resolution for Qdots device was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The step response time is less than 3μs. The resolution, stability, linearity and dynamic range of the bias source exhibits good performance. What's more, the bias source can be controlled locally and online. The results show that it is one effective and feasible topology for experiments in Qdots device application.

A novel type of graphene-like quantum dots, synthesized by oxidation and cage-opening of C60 buckminsterfullerene, has been studied as a fluorescent and absorptive probe for heavy-metal ions. The lattice structure of such unfolded fullerene quantum dots (UFQDs) is distinct from that of graphene since it includes both carbon hexagons and pentagons. The basic optical properties, however, are similar to those of regular graphene oxide quantum dots. On the other hand, UFQDs behave quite differently in the presence of heavy-metal ions, in that multiple sensitivity to Cu2+, Pb2+ and As(III) was observed through comparable quenching of the fluorescent emission and different variations of the transmittance spectrum. By dynamic light scattering measurements we confirmed, for the first time in metal sensing, that this response is due to multiple complexation and subsequent aggregation of UFQDs. Nonetheless, the explanation of the distinct behaviour of transmittance in the presence of As(III) and the formation of precipitate with Pb2+ require further studies. These differences, however, also make it possible to discriminate between the three metal ions in view of the implementation of a selective multiple sensor.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p<0.05; p<0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p<0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

Nanotechnology sparks discussions and concerns about the impacts of new nanomaterials on health and the environment. It holds importance in various domains due to its unique struc-tures. Carbon dots (C-dots) are versatile nanomaterials with applications in bioimaging, sensing, catalysis, polymers, solar cells, and more. They offer desirable characteristics such as stability, cost-effectiveness, biocompatibility, and high photoluminescent quantum yield. C-dots have the potential to replace expensive fluorophores in solar cells. They are catego-rized as carbon quantum dots, graphene quantum dots, and carbonized polymer dots. C-dots have outstanding optical and photoelectric properties with low toxicity. Bottom-up and top-down approaches are used for the synthesis of carbon dots (CDs), with each method im-pacting their physicochemical characteristics. The choice of synthesis method depends on de-sired properties and application requirements. Researchers combine these methods and ex-plore new approaches to enhance synthesis efficiency and tailor CD properties. CDs have di-verse chemical structures with modified oxygen, polymer-based, or amino groups on their surface. Various characterization methods such as HRTEM, XPS, and optical analysis (PL, UV) are used to determine CD structure. Carbon dots (CDs) are cutting-edge fluorescent nano-materials with remarkable qualities such as biocompatibility, low toxicity, environmental friendliness, high water solubility, and photo-stability. They are easily adjustable in terms of their optical properties, making them highly versatile in various fields. CDs find applications in bio-imaging, nanomedicine, drug delivery, solar cells, LEDs, photo-catalysis, elec-tro-catalysis, and other related areas.

A novel metal-doped carbon quantum dot, zinc-chlorine co-doped carbon quantum dots (Zn/Cl-CQDs), has been developed for the fluorescent probe detection of vitamin B2 and the analysis of the correlation properties of this carbon quantum dot and vitamin B2. Stability experiments demonstrate that Zn/Cl-CQDs possess good fluorescence properties under alkaline conditions. However, when vitamin B2 is added into Zn/Cl-CQDs, the fluorescence intensity decreases sharply, indicating that a fluorescence quenching phenomenon occurs between vitamin B2 and Zn/Cl-CQDs. Lastly, the use of Zn/Cl-CQDs in the detection of vitamin B2 tablets and vitamin B2-rich fruits resulted in recovery rates of 98.2% and 100.6%, respectively. Therefore, this method can be well applied to the detection and analysis of vitamin B2, and has great development prospects in the pharmaceutical industry and food monitoring fields.

Carbon dots have received much attention due to their unique physicochemical properties and diverse applications in bioimaging, optoelectronic devices, catalysis, and agriculture. Here in this work, we report a simple hydrothermal synthesis of nitrogen and phosphorus-doped carbon dots (N, P-CDs). The optical and physical properties of the synthesized N, P-CDs were analyzed using systematical spectroscopy and electrical characterization. The synthesized N, P-CDs show strong photoluminescence at 626 nm and demonstrate high stability under UV light and other conditions. Moreover, we incorporate the synthesized N, P-CDs into water spinach by root spraying and leaf spraying. It was found that N, P-CDs could effectively promote the growth of water spinach by increasing the photosynthetic rate, and the content of total phenols and anthocyanins in water spinach

We provide an extensive and systematic investigation of exciton dynamics in droplet epitaxial quantum dots comparing the cases of (311)A, (001) and (111)A surfaces. In spite of a similar s-shell exciton structure common to the three cases, the absence of a wetting layer for (311)A and (111)A samples leads to a larger carrier confinement with respect to (001), where a wetting layer is present. Moreover, this leads to a more pronounced dependence of the binding energies of s-shell excitons on the quantum dot size and to a strong anti-binding character of the positive charged exciton for smaller quantum dots. In-plane geometrical anisotropies of (311)A and (001) quantum dots lead to a large electron-hole fine interaction (fine structure splitting, FSS ~ 100 ueV) whereas for the three-fold symmetric (111)A counterpart this figure of merit is reduced of about one order of magnitude. In all these cases we do not observe any size dependence of the fine interactions. Heavy-hole/light-hole mixing is present in all the studied cases leading to a broad spread of linear polarization anisotropy (from 0 up to about 50%) irrespective of surface orientation (symmetry of the confinement), fine interactions and nanostructure size. These results are important for the further development of ideal single and entangled photon sources based on semiconductor quantum dots.

Graphene quantum dots (GQDs) possess the photosensitive absorption for photoelectrochemical hydrogen evolution owing to special band structures. Whereas they usually confront with photo-corrosion or undesired charge recombination during photoelectrochemical reactions. Hence, we establish the heterojunction between GQDs and MoSe2 sheets via hydrothermal process for improved stability and performance. Photoanodic water splitting with hydrogen evolution boosted by heteroatom doped N,S-GQDs/MoSe2 heterojunction has been attained due to the abundant active sites, promoted charge separation and transfer kinetics with reduced energy barriers. Diphasic 1T and 2H MoSe2 sheets hybridized quantum dots contribute to the Schottky heterojunction, which can play a key role in expedited carrier transport to inhibit accumulative photo-corrosion and increase photocurrent. Heteroatom dopants lead to favored energy band matching, bandgap narrowing, stronger light absorption and high photocurrent density. The external quantum efficiency of doped heterojunction has been elevated twofold over that of the non-doped pristine heterojunction. Modification of graphene quantum dots and MoSe2 heterojunction demonstrate a viable and adaptable platform toward photoelectrochemical hydrogen evolution processes.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

Biomass-derived carbon dots (CDs) are gaining much interest in recent times as it is a sustainable option with abundant availability, low cost, and tunable luminescence. Herein, we report a simple green synthesis method to produce highly fluorescent CDs from Eucalyptus globulus leaves using the one-pot hydrothermal approach. The fabricated CDs exhibit strong blue fluorescence with an excitation and emission maxima of 340 nm and 442 nm respectively. The highest quantum yield (QY) obtained was 60.7%. Due to its promising optical properties and biocompatibility, CDs can be a potential candidate for biosensing applications. Moreover, we employed a life cycle assessment (LCA) cradle-to-gate approach to study the environmental impacts of the synthesis strategy used for the fabrication of CDs. The results point out that citric acid is a main hotspot in CDs synthesis, regarding environmental impacts in most categories. This justifies the introduction of biomass, which reduces the amount of citric acid, thus leading to a more sustainable synthesis strategy for fabricating CDs.

Patterning, stability, and dispersion of the semiconductor quantum dots (scQDs) are the three issues strictly interconnected for successful device manufacturing. Recently several authors adopted direct optical patterning (DOP) as a step forward in photolithography to position the scQDs in a selected area. However, the chemistry behind the stability, dispersion, and patterning has to be carefully integrated to obtain a functional and therefore, commercial device. In this review are described different chemical strategies suitable to stabilize the scQDs both at a single level and as an ensemble with a special focus on the ones compatible with direct optical patterning (DOP). With the same purpose, the scQDs dispersion in a matrix was described in terms of the scQDs surface ligands interactions with the matrix itself. The chemical processes behind the DOP are illustrated and discussed for five different approaches that consider together stability, dispersion, and the patterning itself of the scQDs.

The report introduces hybrid polyelectrolyte-stabilized colloids combining blue and green emitting building blocks, that are citrate carbon dots (CDs) and [TbL]+ chelate complexes with 1,3-diketonate derivatives of calix[4]arene. The joint incorporation of green and blue emitting blocks into the polysodium polystyrenesulfonate (PSS) aggregates is carried out through the solvent-exchange synthetic technique. The coordinative binding between Tb3+ centers and CD surface groups in initial DMF solutions both facilitates joint incorporation of [TbL]+ complexes and the CDs into the PSS-based nanobeads and affects fluorescence properties of [TbL]+ complexes and CDs, as well as their ability to temperature sensing. The variation of the synthetic conditions is represented herein as a tool for tuning the fluorescent response of the blue and green emitting blocks upon heating and cooling. The revealed regularities enable developing either dual band luminescent colloids for monitoring temperature changes within 25-50 C through double color emission, or to transform the colloids into ratiometric temperature sensors via simple concentration variation of [TbL]+ and CDs in initial DMF solution. Novel hybrid carbon dots-terbium chelate PSS-based nanoplatform opens an avenue for new generation of sensitive and customizable single excited dual band nanothermometers.

Fatigue performance and self-repairing activity of asphalt binders are two properties that highly influence the fatigue cracking response of asphalt pavement. There are still numerous gaps of knowledge to fill linked with these two characteristics. For instance, current parameters fail to fully accommodate these two bitumen phenomena. This study aims to propose a new procedure to address this issue utilizing the linear amplitude sweep (LAS) test, LAS with rest period (RP) (LASH) test, and simplified viscoelastic continuum damage (S-VECD) model. This research work used four different types of asphalt binders: neat asphalt (NA), self-healing thermoplastic polyurethane (STPU)-modified bitumen (STPB), self-healing poly (dimethyl siloxane) crosslinked with urea bond (IPA1w)-modified bitumen (IPAB), and styrene–butadiene–styrene (SBS)-modified bitumen (SBSB). Before the testing process, all the materials were subjected to short-term and long-term aging. The new procedure showed a superior capacity to analyze and accommodate all bitumen fatigue performances and self-repairing activities compared to the current method. Another finding proved that asphalt binders with higher self-restoration behavior failed to show better fatigue performance. A breakthrough finding demonstrated that asphalt binder fatigue response augmented when the RP was applied at a higher damage intensity (S) value. STPBs and IPABs reached their highest increments of fatigue response, containing 1.0% of STPU and 0.5% of IPA1w, respectively. Those augmentations were 207.54% and 232.64%, respectively.

Polymer hydrogels are 3D networks consisting of hydrophilic crosslinked macromolecular chains, able to swell and retain water. Since their invention in the 1960s, they have become an outstanding pillar in the design, development, and application of engineered polymer systems suitable for biomedical and pharmaceutical applications (such as drug or cell delivery, regeneration of hard and soft tissues, wound healing, and bleeding prevention, among others). Despite several well-established synthetic routes of polymer hydrogels based on batch polymerization techniques, about fifteen years ago academia started to look for alternative methods involving simpler reaction paths, shorter reaction times, and lower energy consumption. In this context, frontal polymerization (FP) undoubtedly has become an alternative and efficient reaction model that allows for converting monomers into polymers via a localized and propagating reaction, by exploiting the formation and propagation of a “hot” polymerization front, able to self-sustain and propagate throughout the monomeric mixture. Therefore, the present work aims to summarize the main research outcomes, achieved during the last years, concerning the design, preparation, and application of FP-derived polymeric hydrogels, demonstrating the feasibility of this technique for the obtainment of functional 3D networks, and providing the reader with some perspectives for the forthcoming years.

Polymer flooding is one of the most successful chemical EOR methods, and is primarily implemented to accelerate oil production by sweep improvement. However, other benefits have extended the utility of polymers. During the last decade, it has been evaluated for an increasing number of fields, both offshore and onshore. This is a consequence of improved polymer properties, which extends the use to HTHS (high temperature high salinity) conditions and of improved understanding of flow mechanisms such as for heavy oil mobilization. A key issue in understanding polymer performance is to control and predict in-situ porous medium rheology. The first part of this paper reviews recent developments in understanding polymer flow in porous medium. Especially, polymer in-situ rheology and injectivity is discussed. The second part of this paper reports polymer flow experiments using the most applied polymer for EOR processes, HPAM (partially hydrolyzed polyacrylamide). The experiments address high rate near-wellbore behavior (radial flow) as well as reservoir rate steady state flow (linear flow) and discuss differences observed in terms of flow conditions. In addition, impact of oil on polymer rheology was investigated, and compared to single-phase polymer flow in Bentheimer sandstone rock material. Presence of oil leads to a reduction in apparent viscosity.

Fluorescent semiconductor nanocrystals called quantum dots (QDs) have gained attention in biomedical applications, including imaging, molecular tracking, and drug delivery, due to their unique optical properties. However, their use is limited because of safety issues. This study was aimed at assessment the acute toxicity of QDs with different core chemical compositions and surface charges in mice. In addition, the immunotoxicity of CdSe/ZnS QDs was estimated. CdSe/ZnS, PbS/CdS/ZnS, and CuInS2/ZnS QDs were synthesized and modified with PEG derivatives. The hydrodynamic diameters and surface charges of solubilized QDs were characterized. The QD acute toxicity has been shown to depend on both surface charge and core composition. The immunotoxicity of CdSe/ZnS-PEG-OH QDs in mice was assessed after a single intravenous administration of 0.2 LD100 of the QDs. The QDs have been found to increase the spleen weight and cause spleen, thymus, and bone marrow cell depletion. However, these changes are reversible. A transient increase in the levels of proinflammatory cytokines (MCP1 and IL-6) indicates an acute inflammatory response to a single low dose of QDs. Thus, systemic comparative analysis of QD toxicity has shown how the QD core composition and surface properties affect living organisms.

In this work, we investigate by ab initio calculations and optical experiments the sensitiv- ity of graphene quantum dots in their use as devices to measure the presence, and concentration, of heavy metals in water. We demonstrate that the quenching or enhancement in the optical response (absorption, emission) depends on the metallic ion considered. In particular, two test cases of opposite behaviour are considered: Cd 2+ , where we observe an increase in the optical response for increasing concentration, and Pb 2 whose emission spectra are quenched along the concentration rise. We envisage that quantum dots of graphene may be routinely used as cheap detectors to measure the degree of poisoning ions in water

Uniform water soluble MoS2 quantum dots (WS-MSQDs) are synthesized via a sequential combination of sintering/etching/exfoliation method and solvothermal route. The obtained WS-MSQDs with average size of approximately 3.4 nm exhibit sufficient water solubility and remarkable fluorescence properties. The WS-MSQDs have been utilized as a probe for detection of Fe3+ ions with high selectivity and specificity. Furthermore, the WS-MSQDs exhibit high fluorescence stability under different conditions. Finally, the WS-MSQDs are successfully applied for the fluorescence imaging of Fe3+ in living cells, which exhibited practical potential for biomedical applications.

The utilization of black mulberry fruit as a precursor for C-dot synthesis represents a novel ap-proach to biosynthesizing C-dots. Through the implementation of a hydrothermal autoclave, we successfully produced C-dots using the fruit extract. This environmentally conscious and sustain-able method of synthesis presents a promising avenue for C-dot production. Our findings demon-strate the remarkable photocatalytic activity of the C-dots, as evidenced by their effective degra-dation of pollutants under visible light irradiation. This discovery holds significant implications for addressing water contamination issues and promoting environmental remediation efforts. Fur-thermore, we conducted a thorough investigation to determine the optimal doping concentration of C-dots, ultimately identifying 0.2 M as the ideal concentration. At this specific concentration, the photo catalytic degradation of pollutants reached an impressive rate of 95.8%. The enhanced photocatalytic activity can be attributed to the increased electron trapping resulting from the presence of additional surface sites and the absorption of different wavelengths of light. In sum-mary, this research contributes to the sustainable synthesis of carbon dots using black mulberry fruits as a precursor, while also providing a comprehensive analysis of their optical and photo-catalytic properties.

This research review explores the synthesis of graphene quantum dots (GQDs) from biowaste for supercapacitor applications, driven by the need for sustainable and efficient energy storage technologies. GQDs, with their unique properties like high surface area and excellent conductivity, hold promise for enhancing supercapacitor performance. Various synthesis methods, including hydrothermal/solvothermal processes, chemical exfoliation, carbonization/pyrolysis, and microwave-assisted synthesis, are discussed alongside characterization techniques to evaluate GQD properties. Biowaste-derived GQDs demonstrate significant potential by improving specific capacitance and cycling stability in supercapacitor electrodes. Challenges such as scalability and material purity are identified, with future directions focusing on enhancing energy density, cycle life, and cost-effectiveness to propel the adoption of biowaste-derived GQDs in commercial energy storage applications.

Graphene quantum dots (GQDs) have garnered significant attention in recent years due to their unique properties and promising applications in various fields such as electronics, optoelectronics, bioimaging, and sensing. The synthesis of GQDs is a critical step in harnessing their potential, and numerous methods have been developed to produce GQDs with specific properties. This review provides an overview of the different techniques employed for synthesizing GQDs, including top-down and bottom-up approaches. Furthermore, it discusses the advantages, limitations, and potential applications of each method, offering insights into the future direction of GQD synthesis research.

Silica on Silicon is a major optical integration platform, while the emergent class of integrated Laser written circuits' platform offers additionally high customizability, and flexibility for rapid prototyping. However, the inherent waveguides' low core/cladding refractive index contrast characteristic compared to other photonic platforms in silicon or silicon nitride, sets serious limitations for on-chip efficient coupling with single photon emitters, like semiconductor nanowires with quantum dots limiting the applications in quantum computing. A new light coupling scheme proposed here overcomes this limitation providing means for light coupling >50%. The scheme is based on the incorporation of an optical microsphere between the nanowire and the waveguide, properly optimized and arranged in terms of: size, refractive index, distance of microsphere between nanowire and waveguide. Upon suitable design of the optical arrangement, the photonic nanojet emitted by the illuminated microsphere excites efficiently the guided eigenmodes of the input channel waveguide, thus launching light with high coupling efficiency. The method is tolerant in displacements, misalignments, and imperfections and is fabricationally feasible by current state of the art techniques. The proposed method enables the on-chip multiple single photon emitters' integration thus allowing the development of highly customizable and scalable quantum photonic integrated circuits for quantum computing.

The first hyperpolarizability of graphene quantum dots (GQDs) suspended in water was determined using the hyper-Rayleigh scattering (HRS) technique. To the best of our knowledge, this is the first application of the HRS technique to characterize GQDs. Two commercial GQDs (Acqua-Cyan and Acqua-Green) with different compositions were studied. The HRS experiments were performed with an excitation laser at 1064 nm. The measured hyperpolarizabilities were (1.0±0.1) × 10^(-27) esu and (0.9±0.1) × 10^(-27) esu for Acqua-Cyan and Acqua-Green, respectively. The results were used to estimate the hyperpolarizability per nanosheet obtained by assuming that each GQDs has five nanosheets with 0.3 nm thickness. The two-level model, used to calculate the static hyperpolarizability per nanosheet, provides the values of (2.4±0.1) × 10^(-28) esu (Acqua-Cyan) and (0.5±0.1) × 10^(-28) esu (Aqua-Green). The origin of the nonlinearity is discussed on the basis of polarized resolved HRS experiments, and an electric quadrupolar behavior with a strong dependence on surface effects is found. The nontoxic characteristics and order of magnitude indicate that these GQDs may be useful for biological microscopy imaging.

In the last 10 years, carbon dots (CDs) synthesized from renewable organic resources have been gathered a considerable amount of attention in different fields for their peculiar photoluminescent properties. Moreover, the synthesis of CDs fully responds to the principles of the circular chemistry and the concept of safe-by-design. This review will focus on the different strategies for the incorporation of CDs in organic light-emitting devices (OLEDs) and on the study of the impact of CDs properties on the OLEDs performance. The main current research outcomes and highlights are summarized to guide users towards the fully exploitation of use these materials in optoelectronic applications.

An ethanol vapor sensor based on a microfiber with quantum-dots (QDs) gel coating is proposed and demonstrated. The QDs gel was made from UV glue as the gel matrix and the CdSe/ZnS QDs with a concentration of 1mg/mL. The drawing and coating process were conducted by using a simple and low-cost home-made system. The bending, ethanol sensing, temperature response and time response tests were carried out, alternatively. The experimental results show that the fabricated sensor has a high sensitivity of -3.3%/ppm, a really low temperature cross-sensitivity of 0.17 ppm/℃ and a fast response time of 1.1s. The robust structure with ease of fabrication and excellent sensing performance render it a promising platform for real ethanol sensing application.

Semiconductor nanocrystals or quantum dots (QDs), have unique optical and physical properties that make them potential imaging tools in biological and medical applications. However, concerns such as the aqueous dispersivity, toxicity to cells and stability in biological environments may limit the use of QDs in bioapplications. Here, we report an investigation into the cytotoxicity of aqueously dispersed CdSe(S) and CdSe(S)/ZnO core/shell QDs in the presence of human colorectal carcinoma cells (HCT-116) and a human skin fibroblast cell line (WS-1). The cytotoxicity of the precursor solutions used in the synthesis of the CdSe(S) QDs was also determined in the presence of HCT-116 cells and compared to that of the heat-shock protein (Hsp90) inhibitor, 17-AAG. CdSe(S) QDs were found to have a low toxicity at concentrations up to 100 µg/ml, with a decreased cell viability at higher concentrations, indicating a highly dose-dependent response. Meanwhile, CdSe(S)/ZnO core/shell QDs exhibited lower toxicity than uncoated QDs at higher concentrations. Confocal microscopy images of HCT-116 cells after incubation with CdSe(S) and CdSe(S)/ZnO QDs showed that the cells were stable in aqueous concentrations of 100 µg of QDs per ml, with no sign of cell necrosis, confirming the cytotoxicity data. Key words: HCT-116, WS1, water dispersive QDs, aqueous synthesis, cytotoxicity of QDs.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

The escalating demand for multifunctional and advanced materials for growing industries has turned scientific exploration to graphene-based hybrid filler polymer composites. The introduction of graphene with other fillers into polymer matrices results in astonishing properties and thus has gained significant attention in recent years. This study addresses the significance of graphene-based hybrid filler polymer composites in progressive materials science and engineering. The paper encloses some traditional and current preparation techniques employed in the fabrication of composites and a comprehensive review of successfully prepared graphene hybrid polymer composites with enhanced mechanical, thermal, and electrical properties reported in published research. The role of different factors, e.g., filler type, aspect ratios, filler-matrix compatibility, dispersion effects, homogeneity, filler orientation through polymer matrices, and curing conditions, are summarized. Finally, the applications in heavy industries, e.g., aerospace, electronics, energy storage, and automotive sectors were also analyzed. We hope this study will serve as a practical resource for new researchers and practitioners to understand and harness the full potential of these composites in various scientific and industrial fields.

(1) Background: This manuscript introduces the "Lines and Dots" (LAD) technique, a novel method for administering Botulinum Toxin Type A (BoNT-A) in treating horizontal forehead lines. This technique emphasizes precision in targeting nerve endplates, considering individual anatomical variations, and optimizing treatment efficacy. (2) Methods: The LAD technique focus on using the frontalis muscle contraction dynamics to identify the specific distribution of the supraorbital and supratrochlear nerves It involves creating a grid of predetermined lines and points on the forehead that align with nerve paths and motor endplate zones. (3) Results: By targeting injections along these precise lines and points, the LAD technique ensures more effective utilization of BoNT-A. This approach not only enhances the toxin's effect but also allows for a reduction in the overall dosage. The strategic placement of injections results in a more natural, symmetrical, and sustained therapeutic effect, ensuring an improved aesthetic outcome. (4) Conclusions: The LAD technique represents a significant advancement in the realm of cosmetic injectables. It offers a tailored, patient-specific approach, maximizing the effectiveness of BoNT-A injections for treating forehead lines while minimizing risks and enhancing patient satisfaction. This method underscores the importance of a deep anatomical understanding and precision in cosmetic procedures.

In this article, we describe an immunochromatographic test system developed for rapid serodiagnostics of cattle brucellosis using two markers: gold nanoparticles (GNPs) and quantum dots (QDs). The test system was compared with immunochromatographic serodiagnostics systems that use only one marker. The approbation of the test system was conducted on samples of cattle sera with low, but diagnostically significant titers of specific antibodies. We show that when two conjugates are used, the intensity of the detectable signal increases by 2–3 times compared with the test system using the QD conjugate and by more than 9 times compared with the system using the GNP conjugate.

Polyvinyl alcohol (PVA) is highly compatible polymer with biological environments. Specifically, it has been used as a trap for different types of microorganisms in Bio-MEMS, and its properties can be modified to act as an electrode for electrochemical analysis. This study presents a nano-composite developed with PVA, multiwall carbon nanotubes (CNTs) doped with nitrogen, which changes the electrical properties of the polymer and its viscosity to obtain nanofibers by electro-spinning. The proposed nanocomposite was characterized using Fourier transform-infrared and Raman spectroscopy techniques, confirming the presence of the CNTs immersed in the polymer. High-resolution transmission electron microscopy was used to obtain the micrographs that showed the characteristic interplanar distances of the multiwall CNT in the polymeric matrix with values of 3.63 Å. Finally, the CNx mats were exposed to various aqueous solutions in a po-tentiostat to demonstrate the effectiveness of the nanofibers for electrochemical analysis. The CNx-induced changes in the electrical properties of the polymer were identified using cyclic voltammograms, while the electrochemical analysis revealed supercapacitor behavior.

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15%wt) and the sliding regime parameters (load: 1 N, 2.5 N and 5 N, the sliding speed: 0.25 m/s, 0.5 m/s and 0.75 m/s, and the sliding distance: 2500 m, 5000 m and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix.

We present here a theory of Majorana excitons, photo-excited conduction electron-valence band hole pairs, interacting with Majorana Fermions in a Kitaev chain of semiconductor quantum dots embedded in a nanowire. Using analytical tools and exact diagonalisation methods we identify the presence of Majorana Zero Modes in the nanowire absorption spectra.

Electron-hole recombination and narrow range utilization of sunlight limit the photocatalytic efficiency of TiO2. We synthesized a carbon dots (CDs) modified TiO2 nanoparticles (NPs) with flower-like mesoporous structure, i.e., porous TiO2/CDs nanoflowers. Among such hybrid parti-cles, CDs worked as photosensitizers for the mesoporous TiO2 and enabled the resultant TiO2/CDs nanoflowers with a wide-range light absorption. Rhodamine B (Rh-B) was employed as a model organic pollutant to investigate the photocatalytic activity of the TiO2/CDs nanoflowers. The results demonstrated that the decoration of CDs on both TiO2 nanoflowers and P25 NPs enabled a significant improvement of the photocatalytic degradation efficiency compared with the pristine TiO2. TiO2/CDs nanoflowers with porous structure and larger surface areas than P25 showed a higher efficiency owing to prevent local aggregation of carbon materials. All the results revealed that the introduced CDs and the unique mesoporous structure, large surface areas and loads of pore channels of the prepared TiO2 NPs played important roles in the enhancement of the photocatalytic efficiency of the TiO2/CDs hybrid nanoflowers. Such TiO2/CDs composite NPs also opens a door for photodegradation, photocatalytic water splitting and enhanced solar sun-light as light source.

Droplet epitaxy allows the efficient fabrication of a plethora of 3D, III-V-based nanostructures on different crystalline orientations. Quantum dots grown on (311)A-oriented surface are obtained with record surface density, with or without a wetting layer. These are appealing features for quantum-dot lasing, thanks to the large density of quantum emitters and a truly 3D lateral confinement. However, the intimate photophysics of this class of nanostructures has not yet been investigated. Here we address the main optical and electronic properties of s-shell excitons in individual quantum dots grown on (311)A substrates with photoluminescence spectroscopy experiments. We show the presence of neutral exciton and biexciton as well as positive and negative charged excitons. We investigate the origins of spectral broadening, identifying them in spectral diffusion at low temperature and phonon-interaction at higher temperature, the presence of fine interactions between electron and hole spin, and a relevant heavy-hole/light-hole mixing. We interpret the level filling with a simple Poissonian model reproducing the power excitation dependence of the s-shell excitons. These results are relevant for the further improvement of this class of quantum emitters and their exploitation as single photon sources for low density samples as well as for efficient lasers for high density samples.

Highly photoluminescent C-Dots are prepared by hydrothermal reaction of citric acid and piperazine as dual reason in both hydrolysis and surface passivation agent along with the N-doping agent. The resulting C-Dots without external passivation showed PL enhancement by electron transfer from C-Dots-donor to piperazine-acceptor with the maximum emission yields of more than 84%. After mixing the prepared C-Dots with the mixture of EtOH and acetone (1:1 vol %), a novel washing process was performed by centrifugation to remove the precursors and by-products. The resulting C-Dots showed much better stability than dialysis. For evaluating the possible application of the C-Dots as a fluorescent biological probe which possess the wide dosing window and multicolor properties. The C-Dots were localized in perinuclear vacuole-like structures with granular pattern in cytoplasm sparing the nucleus. No signs of any morphological deterioration like nuclear shrinkage were observed.

Cutting-edge technologies are intensifying into new skylines and this remarkable progress has been successfully influenced by the tiny level engineering of carbon dots technology, their syn-thesis advancement and impressive applications in the field of allied sciences. The advances of science and its conjugation with interdisciplinary fields emerged in carbon dots making, their controlled characterization and applications into faster, cheaper as well as more reliable prod-ucts in various scientific domains. Thus, a new era in nanotechnology has developed into carbon dots technology. The understanding of the generation process, control on making processes and selected applications of carbon dots such as energy storage, environmental monitoring, catalysis, contaminates detections and complex environmental forensics, drug delivery, drug targeting and other biomedical applications etc. are among the most promising applications of carbon dots and thus a thrust area of research today. In this regard, various types of carbon dots nano-materials such as oxides, their composites and conjugations etc. have been flocking significant attention due to their remarkable potential in this thrust area of energy, the environment and technology. Thus, the present paper highlights the role and importance of carbon dots, recent advancements in their synthesis methods, properties and emerging applications.

In this paper, based on our previous expertise on ceramic artifacts, several archaeometric methods applied to some samples collected from the Dudești archaeological site (Oltenia region, Romania) are reported for the first time in the literature. The chemical composition and microstructural and morphological characterization of these samples offer important conclusions about the processing conditions. Some specific techniques such as X-ray diffraction (XRD), wave-length-dispersive X-ray fluorescence (WDXRF), Optical microscopy (OM), stereomicroscopy, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy, provide composition information about pigments and their decay processes. Additionally, the Brunauer-Emmett-Teller (BET) method helps to estimate pore sizes and specific surface areas. Thermal analysis (TGA) was used to establish details regarding the production technology and the raw materials source used to make the ceramics, too. The obtained results indicated that the ceramics are based on a paste of muscovite, feldspar, with high plasticity, quartz, melanterite, and calcite, the latter in very low concentrations. According to the obtained results, we could assume that non-calcareous clays are present in the investigated samples because calcium exists in low concentrations. Gypsum is present, too, in very low concentration, identified by the presence of sulfate group in WDXRF. In the same context, iron oxides significantly impact the firing atmosphere of iron-rich clay, resulting in blackening under reducing conditions and reddish coloration under oxidative conditions. Using hematite and gypsum as pigments further contributes to the color variations in the pottery. The consistent firing temperature range of 200-600 °C in Dudești pottery implies a standardized production process, the variation in color being dependent on the specific reducing/oxidative regime conditions. This relationship between clay composition and local sources suggests a connection to Neolithic pottery production in the region and their color depending on the reducing/oxidative regime conditions.

This paper is focused on understanding multiscale modelling to obtain a bridge among different time and length scales of simulation techniques. These techniques are vital as it holds the potential to understand and predict the capabilities of polymer nanocomposites (PNCs). However, an appropriate approach in controlling the interfacial interaction between nanoparticle and polymer in nanocomposites structure is still needed to develop. In this review, an initial brief introduction to various trending simulation techniques has been discussed at all three levels of scale (nm, μm, mm). Later, descriptive study on fundamental issues such as thermodynamics, kinetics, mechanical properties, and morphology has been studied deeply. The multiscale modeling bridges the gaps of simulation between the different scales of models from molecular to mesoscale levels working over the broad range of length and timescale. Through the sequential, adaptive, and concurrent approaches, we can develop a system that may comprehend multiscale mode modeling adaptive resolution approach has recently added approach the molecule of the subject can shift their position freely in the domain and through this approach and studied the Brownian motion. Co-The co-current coach is also termed as handshaking path and it is linked aiming at different scale models. Covering the rigid techniques smoothly and linking them at different scales helps in normalizing the statistical behaviour.

Luminescent carbon dots (CDs) were locally synthesized in the core of CYTOP fibers using IR femtosecond laser direct writing (FLDW), a one-step simple method serving as a post-treatment of the genuine fiber. This approach enables the creation of several types of modifications such as ellipsoid voids. The CDs and photoluminescence (PL) distribute at the periphery of the voids. The PL spectral properties were studied through Excitation Emission Matrix in the visible range and excitation/emission spectrum in UV/visible range. Our finding reveals the presence of at least 3 distinct luminescent species, facilitating a broad excitation range extending from UV to green, and light emission spanning from blue to red. The average laser power and dose influence the quantity and ratio of these luminescent CD species. Additionally, we measured the spatially resolved lifetime of the luminescence during and after the irradiation. We found longer lifetimes at the periphery of the laser-induced modified regions and shorter ones closer to the center, with a dominant lifetime ~ 2ns. Notably, unlike many other luminophores, these laser-induced CDs are insensitive to oxygen, enhancing their potential for display or data storage applications.

Cs2NaInCl6 double perovskites, which have excellent photoelectric conversion properties and are non-toxic and lead-free, have recently attracted much attention. In particular, double perovskite quantum dots (QDs) are considered to be a promising material for optoelectronic device applications. Ligands such as oleic acid (OA) and oleylamine (OAm) are essential for the synthesis of perovskite QDs, but their roles on double perovskite QDs are not yet clear. In this study, we have investigated the binding of OA and OAm to Cs2NaInCl6 QDs through FTIR and NMR and their effects on the surface defect reduction and stability improvement for Cs2NaInCl6 QDs. We found that only OAm was bound to the QD surfaces while OA was not. The OAm has a great effect on photoluminescence quantum yield (PLQY) improvement by passivate the QD surface defects. The stability of the QDs was also investigated, and it was shown that OA played a significant role in the stability of the QDs. Our findings provide critical insights into the roles of the ligands for photophysical properties and stability of lead-free double perovskite QDs.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Hydrogels have gained significant attention as vehicles for transdermal delivery systems. These polymeric-structured substances have been implemented in pharmaceutical and cosmetic applications. Many factors are employed in their preparation. Light, pH, temperature and specific molecules ligands are commonly used in the production of hydrogels. The Transdermal delivery system (TDD) is a widely used route, used to deliver actives/drugs via the skin. Hydrogels as a TDD have been shown to be efficient in enhancing the efficacy in delivering the actives and drugs. The aim of this review is to discuss the hydrogels application in both dermatological therapeutic and cosmetic applications, covering the types, and properties of hydrogel polymer networks. Furthermore, this review presents one of the most extensively used polymers (Hyaluronic acid HA) in this field and discusses the properties, preparation methods and applications of HA hydrogel patches as a delivery system, including methods of loading the actives and the releasing of these actives from them.

Seeing atomic configuration of single organic nanoparticles at sub-Å spatial resolution by transmission electron microscopy has been so far prevented by the high sensitivity of soft matter to radiation damage. The difficulty is related to the need to irradiate the particle with a total dose of few electrons/Å2, not compatible with the electron beam density necessary to search the low-contrast nanoparticle, to control its drift, to finely adjust the electro-optical conditions and particle orientation, and to finally acquire an effective atomic resolution image. On the other hand, the capability to study individual pristine nanoparticles, such as proteins, active pharmaceutical ingredients, and polymers, with peculiar sensitivity to the variation of the local structure, defects, and strain, would provide advancements in many fields, including materials science, medicine, biology, and pharmacology. Here we report direct sub-ångström resolution imaging at room temperature of pristine unstained crystalline polymer-based nanoparticles. This result is obtained by combining low-dose in-line electron holography and phase-contrast imaging on state-of-the-art equipment, providing an effective tool for the quantitative sub-angstrom imaging of soft matter.

Carbon Quantum Dots (CQDs) have emerged as promising nanomaterials for enhancing the performance of supercapacitors, offering unique advantages such as high surface area, excellent electrical conductivity, and tunable surface chemistry. This review provides a comprehensive overview of recent advancements in the synthesis, characterization, and integration of CQDs into supercapacitor devices. Various synthesis methods, including chemical oxidation, hydrothermal/solvothermal methods, microwave-assisted synthesis, and pyrolysis, are discussed, highlighting their impact on the structural and electrochemical properties of CQDs. Characterization techniques such as transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy, and photoluminescence (PL) spectroscopy are elucidated for assessing the morphology, crystallinity, and optical properties of CQDs. The integration of CQDs into supercapacitors, including their utilization in composite electrodes, binder-free electrodes, and doping strategies, is explored to enhance specific capacitance, energy density, power density, and cycle stability of the devices. Challenges and future perspectives in the field are outlined, emphasizing the need for scalable synthesis methods, enhanced electrochemical performance, and sustainable device engineering to realize the full potential of CQD-based supercapacitors for various energy storage applications. This review aims to provide insights into the current state of research and guide future endeavors towards developing high-performance and environmentally sustainable energy storage technologies.

This review study, delves into the groundbreaking potential of quantum dots in revolutionizing the field of stem cell tracking for regenerative medicine. Beginning with an introduction that underscores the pivotal role of stem cell tracking in regenerative medicine, this review introduces quantum dots as promising tools for this purpose. It proceeds to explore the fundamental properties of quantum dots, including the quantum confinement effect, size-dependent emission, and exceptional brightness, which render them ideal candidates for stem cell tracking. The historical evolution and recent advancements of quantum dot technology in biomedicine are discussed, emphasizing their growing importance in terms of biocompatibility and safety. Furthermore, various labeling strategies for stem cells using quantum dots are detailed, encompassing surface modification and internalization techniques, with a comparison of their respective advantages and drawbacks. A comprehensive exploration of the wide range of imaging modalities that synergize with quantum dots for stem cell tracking is presented, accompanied by an evaluation of their strengths and limitations. Real-world applications of quantum dot-based stem cell tracking in regenerative medicine, spanning tissue regeneration to disease modeling, are showcased, with illuminating case studies. Current challenges and limitations in quantum dot-based stem cell tracking, including long-term stability and regulatory considerations, are addressed, and innovative directions and emerging trends in quantum dot technology are proposed. Safety considerations and strategies to enhance quantum dot biocompatibility within biological systems are discussed, while ethical and regulatory implications related to their use in stem cell tracking are explored, promoting responsible research and development practices. Finally, the review concludes by summarizing key insights and takeaways, reaffirming the transformative potential of quantum dots in advancing stem cell tracking and the field of regenerative medicine.

In recent years, genetic research has been developing rapidly and taking on a larger role in research and medicine. The synthesis of any particle that can be used in this research can pave the way for new developments in this field. This research aims to develop a chemical method to produce nitrogen-doped carbon quantum dots - economical and bio-sourced substances that bind to genomic DNA. Carbon quantum dots are produced by the green synthesis hydrothermal method from radish, which is abundant in nature, and economically affordable. Nitrogen is added to increase the fluorescence properties of the produced carbon quantum dots and to improve their binding to DNA. The synthesized nitrogen-doped carbon quantum dots (N-CQDs) were tested through chromosome imaging subsequently. It was shown that N-CQDs can bind to the chromosomes, and N-CQDs reflected green light better than DAPI under the FITC filter, a potential advantage of using N-CQDs over DAPI in chromosome imaging.

The aim of this research was to undertake laboratory testing to investigate the beneficial effects of epoxy resin grouts on the physical and mechanical properties of sands with a wide range of granulometric characteristics. Six sands, of different particle size and uniformity coefficients, were grouted using epoxy resin solutions with three ratios of epoxy resin to water (3.0, 2.0 and 1.5). A set of unconfined compressive strength tests were conducted on grouted samples at different curing periods and a set of long-term unconfined compressive creep tests in dry and wet conditions after 180 days of curing were also carried out, in order to evaluate the development of the mechanical properties of the sands, as well as, the impact of water on them. The findings of the investigation showed that epoxy resin resulted in appreciable strength values in the specimens, especially those of fine sands, grouted with the different epoxy resin grouts. In general, the compressive strength varied between 0.68 - 5.60 MPa and the modulus of elasticity between 75 - 480 MPa, after a curing period of 180 days. In terms of physical properties, the permeability and porosity (before and after the grouting process) were estimated. Grouts with an epoxy resin to water ratio of 3 decreased permeability by up to four orders of magnitude. Using laboratory results and regression analysis, three mathematical equations were developed that relate each of the dependent variables; compressive strength, elastic modulus, and coefficient of permeability, with particular explanatory variables.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

Chitosan arouses large interest due to its properties and possible applications. Every year the number of publications and patents based on this polymer increases. Chitosan exhibits poor solubility in neutral and basic media limiting its use in such conditions. Another serious obstacle is directly related to its natural origin. Chitosan is not a single polymer with a defined structure but a family of molecules with differences in their composition, size, and monomer distribution. These properties have a fundamental effect on the biological and technological performance of the polymer. Moreover, some of the biological properties claimed are discrete. In this review, we discuss how chitosan chemistry can solve the problems related to its poor solubility and can boost the polymer properties. We focus on some of the main biological properties of chitosan and the relationship with the physicochemical properties of the polymer. Then, we visit two polymer applications related to green processes: the use of chitosan in the green synthesis of metallic na-noparticles and its use as support in biocatalyst. Finally, we briefly describe how making use of the technological properties of chitosan it is possible to develop a variety of systems for drug delivery

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

The success of composite materials is attributed to the nature of bonding at the nanoscale and the resulting structure-related properties. This study reports the interaction, electronic, and optical properties of diamond nanothread/polymers (cellulose and epoxy) and boron nitride nanotube/calcium silicate hydrate composites using density functional theory modeling. Our findings indicate that the interaction between the nanothread and polymer is due to van der Waals-type bonding. Minor modifications in the electronic structures and absorption spectra are noticed. Conversely, the boron nitride nanotube and calcium silicate hydrate composite display an electron-shared type of interaction. The electronic structure and optical absorption spectra of the diamond nanothread and boron nitride nanotube in all configurations studied in the aforementioned composite systems are well maintained. Our findings offer an electronic-level perspective into the bonding characteristics and electronic-optical properties of diamond nanothread/polymer and boron nitride nanotube/calcium silicate hydrate composites for developing next-generation materials.

The recent years various, there huge interest to improve the efficiency of smart electronic and optoelectronic devices via developing emerging materials and printing technologies. However, printing technologies becomes one of the most interesting areas for researcher over a convenient coating method because it not only helps to improve the efficiency of device but also help for rapid, reproducible, and low-cost production which open as a new window for mass production for commercial use. Inkjet printing technology has become the most attractive among various printing technologies due to which it is acceptable in most of scientific and various of industrial applications. This review paper presents an overview of the investigations on formulation of the ink, fabrication, and the applications of conductive polymer via inkjet printing for variety of devices including supercapacitors, sensors, electrochromic devices, and patterning of conductive polymers on flexible substrates. The review covers the different conducting polymer explored for supercapacitors, sensors, electrochromic devices, and patterning of conductive polymers, their ink formulation, inkjet printing process and their keys features. This review also presented future perspectives for inkjet printing technology for advanced electronic, optoelectronic, and other conductive polymer-based devices. We believe this review provides new direction to next generation conductive polymer-based devices for various applications.