Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (>70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

The article offers a comprehensive overview of recent breakthroughs in eco-friendly polymers and polymer composites, underscoring their pivotal role in addressing sustainability challenges across diverse industrial sectors. Despite encountering obstacles related to performance and processability, biopolymers sourced from renewable materials emerge as promising alternatives for the plastics that are currently used by human beings. Natural fillers are highlighted as a strategic avenue for crafting sustainable composites, with residual natural fillers being particularly explored. Heightened environmental concerns propel discussions on the criticality of integrating biodegradable materials with natural fillers, underlining the urgency for clear frameworks and financial incentives to support adoption of these materials. Additionally, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on the utilization of polyhydroxyalkanoate (PHA) in composite materials and its market prospects. Moreover, it emphasizes the indispensable need for ongoing research and development endeavors to address environmental challenges within the polymer sector, reflecting a mounting interest in sustainable materials across industries.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Chemical flooding is one of the effective methods to recover large volumes of oil from sandstone formations after primary depletion. However, silica dissolution often occurs during Alkaline-Surfactant-Polymer (ASP) flooding, affecting the petro-physical properties of the formation. To address this issue, samples from Berea sandstone formations were treated with various brine solutions, through static tube tests and core flooding experiments. Analytical tests such as DR/2800 spectrophotometer and scanning electron microscope were used to evaluate the silica solubility and the alteration in mineral content. The results indicated that the silicate contents decreased after the saturation due to silica solubility in the solution. Increasing brine salinity to 40,000ppm and introducing Magnesium and Calcium ions to the solution, reduces the silicate contents by 5.03 % and 7.32 %. Moreover, saturating the samples with ASP solution, further reduced the silicate contents by 14.86 %. This reduction is associated with a relative increase in silica solubility and pH of the solution. Silica dissolution affects the pore microstructure, which resulted in increasing the porosity and pore volume after the core flooding. The injection of the ASP solution increased the porosity by 5.83%, thus the pore volume increased from 17.72 to 18.76cc. This is associated with the high silica solubility and the increase of solution pH in the ASP solution. The permeability of the samples generally reduced after the core flooding, due to the silica solubility. However, injecting the ASP solution, resulted in a major reduction of the permeability by more than 75%. These changes in the petro-physical properties can lead to severe formation damage, and affect hydrocarbon production. This study assists in understanding the impact of silica dissolution during ASP treatment and addresses the factors involved. Efficient utilization of chemical flooding can help mitigating silicate scaling within the formation, and extend field productivity.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

In a previous study we could show a change of membrane morphology and gas separation performance by varying the recipe of a casting solution based on polysulfone in a determined solvent system. Although all results were very reproducible, all used solvents were harmful and not sustainable. In this study therefore, the solvents tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAc) are replaced by the more sustainable solvents 2-methyl-tetrahydrofuran (2M-THF), N-butyl pyrrolidinone (NBP) and cyclopentyl methyl ether (CPME). The gas permeation performance and for the first time morphology of the membranes before and after solvent replacement were determined and compared by single gas permeation measurements and SEM microscopy. It is shown, that THF can be replaced by 2M-THF and NBP without decreasing the gas permeation performance. With CPME replacing THF no membranes were formed. Best gas permeation results showed systems with 2M-THF as THF alternative. Permeances for the tested gases oxygen (O2), nitrogen (N2), carbon dioxide (CO2) and methane (CH4) were 2.66·10-4, 3.89·10-5, 1.53·10-3 and 4.52·10-5 mL(STP)/cm²·min·bar, respectively. permselectivities of those membranes for the gas pairs O2/N2, CO2/N2 and CO2/CH4 were 6.7, 38.3 and 34.0, respectively. When additionally replacing DMAc in the solvent system no or only porous membranes were obtained, even if the precipitation procedure was adjusted. These findings indicate that a complete replacement of the solvent system without affecting the membrane morphology or gas permeation performance is not possible. By varying the temperature of the precipitation bath an easy adjustment to mechanically stable PSU membranes is possible, if just THF was replaced by 2M-THF.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Optimum selectivity of enhanced oil recovery techniques would play a substantial role in the economic prosperity of petroleum industries which might be virtually eliminated unnecessary expenditures. In this paper, the simultaneous utilization of foaming agent, surfactant polymer (SP), and supercritical carbon dioxide were taken into the investigation under the miscible condition to evaluate the efficiency of each scenario on the cumulative recovery factor, water cut and pressure drop. According to the results of this experimental evaluation, SP-foam flooding had witnessed the highest blockage which is caused to have the maximum recovery factor due to the mobilization of more oil volume in the low permeable pores and cracks. Furthermore, the utilization of surfactant with supercritical carbon dioxide had experienced the least recovery factor regarding the insufficient foam generation which is led to less mobilization of oil phase in the pore throats.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

The objective of this research project was to evaluate the effects of the addition of inorganic fillers into PEBA at various loading levels on the processing, mechanical, thermal and physical properties of the polymer. The composites investigated in this study were Pebax® 6333 SA01 MED (PEBA100) with 10 wt.%, 20 wt.% and 30 wt.% Barium Sulphate (PEBA/BaSO4) and Bismuth Oxychloride (PEBA/BiOCl) respectively. Composites were prepared using twin screw extrusion and injection moulding. Post-processing, composite samples were analysed for their mechanical properties (via tensile, impact and flexural analysis), thermal properties (via differential scanning calorimetry), rheological performance (via melt flow index) and physical properties (via density analysis and ash content testing). The results of which reveal how filler type and concentration influence PEBA composites. The results of the study suggest that BiOCl filler enhances the aesthetic properties, increases the stiffness, while maintaining some level of flexibility with minimal adverse effects on the tensile and impact strength. When comparing BiOCl to BaSO4 filled composites, it was clear that depending on the application of the polymer composite, BiOCl may provide more desirable properties. The study highlights the importance of optimising filler concentration and processing conditions to achieve desired composite properties for specific medical applications.

The goal of this work was to develop the acrylonitrile-butadiene (NBR) elastomer composites filled with hydroxyapatite (HAP), which were characterized with improved cure characteristics and burning resistance. Silane, i.e., (3-aminopropyl)-triethoxysilane, ionic liquid, i.e., 1-decyl-3-methylimidazolium bromide and surfactant, i.e., cetyltrimethylammonium bromide, were used to improve the filler’s dispersibility in the elastomer matrix and to reduce the time and temperature of vulcanization. The effect of HAP and dispersants on the cure characteristics, crosslink density and physico-chemical properties of NBR composites was explored. The additives used, especially the ionic liquid and surfactant, effectively improved the dispersion of HAP in NBR matrix. The amount of HAP and the dispersant used strongly affected the cure characteristics and crosslink density of NBR. The optimal vulcanization time significantly increased with HAP content and was pronouncedly reduced when ionic liquid and surfactant were applied. In addition, ionic liquid and surfactant significantly lowered the onset vulcanization temperature, improved the crosslink density and hardness of the vulcanizates, while impairing their elasticity. HAP and dispersants did not significantly affect the damping properties and chemical resistance of NBR vulcanizates. Above all, application of HAP considerably enhanced the resistance of vulcanizates to thermo-oxidative aging and reduced their flammability compared to the unfilled NBR.

The characteristics of tight sandstone, such as small pores, complex pore structures, low permeability, and low porosity, make it difficult to accurately characterize its pore structure. This represents a major challenge in the exploration and development of tight sandstone oil and gas reservoirs. This article conducts a simulation study on the impact of characteristic parameters such as pore size, coordination number, pore-throat ratio, and wettability on microscopic remaining oil after polymer flooding, thereby quantifying the types of remaining oil.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

Infill drilling is one of the most effective methods to improve the performance of poly-mer flooding. The difficulties related to infill drilling are determining the optimal numbers and placements of infill wells. In this study, an improved archimedes optimization algorithm with Halton sequence (HS-AOA) was proposed to overcome the aforementioned difficulties. First, to optimize the infill well placement for polymer flooding, an objective function that considered the economic influence of infill drilling was developed. Then, the novel optimization algorithm (HS-AOA) for infill well placement was developed by combining the AOA with the Halton se-quence. The codes were developed in MATLAB and connected to a commercial reservoir simula-tor CMG STARS to carry out the infill well placement optimization. Finally, the HS-AOA was compared to the basic AOA to confirm its reliability and then used to optimize the infill well placements for polymer flooding in a typical offshore oil reservoir. The results showed that the introduction of the Halton sequence into AOA effectively increased the diversity of the initial ob-jects in the AOA and avoided the HS-AOA trapping into the local optimal solutions. The HS–AOA outperformed the AOA. It was an effective approach to optimize the infill well placement for polymer flooding processes. In addition, infill drilling could effectively and economically im-prove the polymer flooding performance in offshore oil reservoirs. The NPV of the polymer flooding case with infill wells determined by HS-AOA reached 3.5 × 108 $, which was an increase of 7% over that of the polymer flooding case. This study presents an effective method for opti-mizing infill well placement for polymer flooding processes. It also can serve as a valuable refer-ence for other optimization problems in the petroleum industry, such as joint optimization of well control and placement.

The present investigation highlights the synthesis of polyaniline (PANI) coated graphene oxide doped with SrTiO3 nanocube nanocomposites through facile in-situ oxidative polymerization method for the efficient removal of carcinogenic dyes, namely, the cationic dye methylene blue (MB) and the anionic dye methyl orange (MO). The synthesised nanocomposites were characterised by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adsorption efficiencies of graphene oxide (GO), PANI homopolymer and SrTiO3 nanocubes-doped nanocomposites were assessed by monitoring the adsorption of methylene blue and methyl orange dyes from aqueous solution. The adsorption efficiency of nanocomposites doped with SrTiO3 nanocubes were found to be of higher magnitude as compared with undoped nanocomposite. Moreover, the nanocomposite with 2 wt% SrTiO3 with respect to graphene oxide demonstrated excellent adsorption behaviour with 99% and 91% removal of MB and MO respectively, in a very short duration of time.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

Salt marshes in the southern North Sea are part of the UNESCO World Heritage Site Wadden Sea, the largest unbroken system of intertidal sand and mud flats in the world. They provide a very high nature value while significantly contributing to coastal flood and erosion risk management as a nature-based element of flood and erosion risk management systems for the densely populated coastal area. Climate change-induced sea-level rise is a significant concern: An integrated approach to salt marsh management adapted to the effects of climate change necessitates a understanding of the impact of different management strategies. This review commences with a description of the biogeomorphological conditions and processes in salt marshes for a better understanding of the natural dynamics and how they are influenced by management and climate change. In a second step, the impact of salt marshes on hydrodynamic processes and their role as nature-based element of flood and erosion risk management is presented. Management options and implementation methods are discussed and analysed concerning coastal flood management and nature conservation requirements. In conclusion, a targeted salt marsh management needs to consider the initial conditions and the development aims of the specific site integrated in a conceptual framework. Salt marshes have the potential to adapt to sea-level rise, thereby contributing to the long-term protection of coastal areas.

The microscopic pore structure of tight sandstone reservoir significantly influences the characteris-tics of CO2 flooding after water flooding. The research was conducted using various techniques such as casting thin sections, high pressure mercury injection, scanning electron microscopy, Nu-clear magnetic resonance (NMR) testing, and a self-designed high-temperatures and high-pressures microscopic visualization displacement system. Three type cores with different pore structures were selected for the flooding experiments and the microscopic visualization displace-ment experiments, including CO2 immiscible flooding, near-miscible flooding, and miscible flood-ing after the conventional water flooding. The characteristics of CO2 flooding and the residual oil distribution after water flooding were quantitatively analyzed and evaluated. The results show that: (1) During the water flooding process, the oil produced from type I and type III samples mainly comes from large and some medium pores. Oil utilization of all pores is significant for type II samples. The physical properties and pore types have a greater impact on water flooding. Type I and II samples are more suitable for near-miscible flooding after water flooding. Type III samples are more suitable for miscible flooding after water flooding. (2) In the CO2 flooding, oil recovery increases gradually with increasing pressure for all three types of samples. Type II core samples have the highest recovery. Before miscibility, the oil recovered from type I and type II samples was primarily from large pores, however, the oil recovery mainly comes from medium pores when reaching miscibility. As for the type III samples, the oil produced in the immiscible state mainly comes from large and medium pores, and the enhanced oil recovery mainly comes from medium and small pores after reaching the near-miscible phase. (3) It can be seen from the microscopic re-sidual oil distribution that oil recovery will increase as the petrophysical properties of the rock model improve. The oil recovery of near-miscible flooding after water flooding regarding the type II model is up to 68.11%. The oil recovery of miscible flooding after water flooding about type III model is the highest at 74.57%. With increasing pressure, the proportion of flake residual oil grad-ually decreases, while the proportion of droplet-like and film-like residual oil gradually increases. Type II samples have a relatively large percentage of reticulated residual oil in the near-miscible stage.

Nanomaterials have shown significant promise for enhancing the performance of composite materials and increasing their functionality for various industrial applications. This review explores the unique properties of nanomaterials, particularly carbon-based nanomaterials, and provides key findings in utilizing them to enhance composite performance. It highlights specific nano-based composite materials and their significant potential in advancing the field of nanocomposites. Challenges associated with nanocomposite production and utilization are also discussed, along with possible solutions to address them. Finally, the study provides recommendations for continued research and innovation in nanocomposites to fully unlock the benefits of these advanced materials for broader future applications.

This paper presents GeoFlood, a new open-source software package for solving shallow water equations (SWE) on a quadtree hierarchy of mapped, logically Cartesian grids managed by the parallel, adaptive library ForestClaw (Calhoun and Burstedde, 2017). The GeoFlood model is validated using standard benchmark tests from Neelz and Pender (2013) and against George (2011) results obtained from the GeoClaw software (Clawpack Development Team, 2020) for the historical Malpasset dam failure problem. The benchmark test results are compared against GeoClaw and software package HEC-RAS (Hydraulic Engineering Center - River Analysis System, Army Corp of Engineers) results (Brunner, 2018). This comparison demonstrates the capability of GeoFlood to accurately and efficiently predict flood wave propagation on complex terrain. The results from comparisons with the Malpasset dam break show good agreement with the GeoClaw results and are consistent with the historical records of the event.

Coastal inundation is recently requiring a significant attention worldwide. The increasing frequency and intensity of extreme events (sea storms, tsunami waves) are highly stressing the coastal envi-ronments, e.g. endangering a large number of residential areas, ecosystems, tourist facilities, and also leading to potential environmental risks. Predicting such events and the generated coastal flooding is thus of paramount importance and can be reached by exploiting the potential of different tools, like remote sensors and numerical modeling. To this aim, a combination is possible between marine radars and wave-resolving propagation models. While instruments like X-band radars are able at precisely reconstructing both wave field and bathymetry within a coastal area that is some kilometers offshore, wave-resolving Boussinesq-type models can reproduce the wave propagation in the nearshore and the consequent coastal flooding. The present work illustrates the reconstruc-tion of coastal data (wave field and seabed depth) conducted using radar signals and a specifically suited data processing, named “Local Method”, and the use of such coastal data to run numerical simulations of wave propagation (using the FUNWAVE-TVD solver) aimed at reproducing coastal inundation over different scenarios. Such scenarios are built using two different European beaches, i.e. Senigallia (Italy) and Oostende (Belgium), and three different directional spreading values, to evaluate the performances in case of either long- or short-crested waves. The overall validation of the methodology, in terms of maximum inundation, shows good performances, especially in case of short-crested wind waves. Furthermore, the application on the Oostende beach demonstrates that the present methodology might work only using open-access tools, i.e. an easy investigation of the coastal inundation and a potential low-cost integration into early warning systems.

The susceptible-infected-recovered-vaccinated-deceased (SIRVD) epidemic compartment model extends the SIR model to include the effects of vaccination campaigns and time-dependent fatality rates on epidemic outbreaks. It encompasses the SIR, SIRV, SIRD, and SI models as special cases, with individual time-dependent rates governing transitions between different fractions. We investigate a special class of exact solutions and accurate analytical approximations for the SIRVD and SIRD compartment models. While the SIRVD and SIRD equations pose complex integro-differential equations for the rate of new infections and the fractions as a function of time, a simpler approach considers determining equations for the sum of ratios for given variations. This approach enables us to derive fully exact analytical solutions for the SIRVD and SIRD models. For nonlinear models with a high-dimensional parameter space, such as the SIRVD and SIRD models, analytical solutions, exact or accurately approximative, are of high importance and interest: not only as suitable benchmarks for numerical codes, but especially as they allow us to understand the critical behavior of epidemic outbursts as well as the decisive role of certain parameters. In the second part of our study, we apply a recently developed analytical approximation for the SIR and SIRV models to the more general SIRVD model. This approximation offers accurate analytical expressions for epidemic quantities, such as the rate of new infections and the fraction of infected persons, particularly when the cumulative fraction of infections is small. The distinction between recovered and deceased individuals in the SIRVD model affects the calculation of the death rate, which is proportional to the infected fraction in the SIRVD/SIRD cases but often proportional to the rate of new infections in many SIR models using a posteriori approach. We demonstrate that the temporal dependence of the infected fraction and the rate of new infections differs when considering the effects of vaccinations and when the real-time dependence of fatality and recovery rates diverge. These differences are highlighted for stationary ratios and gradually decreasing fatality rates. \Revised{The case of stationary ratios allows one to construct a new powerful diagnostics method to extract analytically all SIRVD model parameters from measured COVID-19 data of a completed pandemic wave.

The leather industry is one of the most polluting industries in the world due to the large amounts of waste following the raw hides processing, but also due to the high content of chemicals present in their composition. The main problem of chromium-tanned leather solid waste is related to their storage, because of the ability of chromium to leach in soil or water, and also owing to the high ability of trivalent chromium to oxidize to its toxic form, hexavalent chromium. The purpose of this study is to present the latest methods for extracting trivalent chromium from the composition of solid leather wastes. The extraction methods identified in the present study are based on acid/basic/enzymatic hydrolysis and substitution with the help of organic chelators (organic acids and organic acid salts). In addition, the study includes a comparative analysis between the advantages and disadvantages of each identified extraction method. At the same time, the study also presentes alternative chromium extraction methods based on the combination of conventional extraction methods and ultrasound-assisted extraction.

In order to achieve the dual carbon goal and simplify the decarbonization process, a CO2 recovery process of the fire-flooding exhaust was designed. The process adopted the two-stage membrane separation method to recover CO2 and obtain high purity CO2 rich flow, and then through the mixed refrigerant liquefaction and rectification column, food grade liquid CO2 was obtained. HYSYS process simulation shows that for the fire-flooding exhaust with a flow rate of 1000 kg/h and a given composition, the process can achieve a CO2 recovery of 69.02%, total product sales S=2086.8 yuan/h, and specific power consumption of 2.818 kW∙h/kg. On this basis, a hybrid simulation platform of HYSYS & Matlab was established. Taking the specific power consumption of the product as the objective function, sequential quadratic programming (SQP) algorithm was adopted to optimize the process, and the optimized specific power consumption was reduced by 18.8%. Finally, by adjusting N2/CO2 components, the adaptability of the optimization condition was analyzed.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

IoTs and WSNs utilize their connectivity to enable solutions supporting a spectrum of industries in different and volatile environments. To effectively enhance the security and quality of service of networks, empirical research should take into account a variety of factors and be structured in a replicable manner. This will not only ensure scalability but also enable verification of conclusions, leading to more constructive outcomes. Cooja offers limited performance analysis capabilities of simulations, which are often extracted and calculated manually. In this paper, we introduce a framework and a toolkit that enable researchers to conduct structured and conclusive experiments considering different factors and metrics, experiment design to results analysis. Besides, this tool summarizes multiple network metrics and allows multiple scenarios. As proof of concept, this paper studies the flooding attacks on IoT and illustrates their impact on the network, leveraging the proposed framework and tools.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

Novel bio-inspired materials have gained recently great attention, especially in medical applications. Applying sophisticated design and engineering methods, various polymer-polymer hybrid systems with outstanding performance have been developed in last decades. Hybrid systems composed of bioelastomers and hydrogels are very attractive due to their high biocompatibility and elastic nature for advanced biomaterials used in various medical applications such as drug delivery systems and scaffolds for tissue engineering. Herein, we describe the advances in current state-of-the-art design, properties and applications of polymer-polymer hybrid systems in medical applications. Bio-inspired functionalities, including bioadhesiveness, injectability, antibacterial properties and degradability applicable to advanced drug delivery systems and medical devices will be discussed in a context of future efforts towards development of bioinspired materials.

Nanostructured polymer dispersed liquid crystals (nano-PDLCs) are transparent and optically isotropic materials, in which submicron-sized liquid crystal (LC) domains are dispersed within a polymer matrix. Nano-PDLCs can induce their birefringence by applying an electric field (E-field) based on reorientation of LC molecules. If nano-PDLCs are utilized as light scattering-less birefringence memory materials, it is necessary to suppress the relaxation of LC molecules orientation after removal of the E-field. We focused on a ferroelectric smectic A (SmA) to suppress the relaxation of LC molecules due to their layered structure and high viscosity. Although nano-PDLCs require a strong E-field to reorient LC molecules due to the anchoring effect on the LC/polymer interface, the required field strength can be reduced by using a ferroelectric smectic A (SmAF) LC with a large dielectric constant. In this study, we fabricated a nano-PDLC by irradiating an ultraviolet light to a mixture comprising of a SmAF LC, photocurable monomers and a photo-initiator and its electro-birefringence effect was evaluated using a polarizing optical microscopy. After removal of an E-field, enhanced memory effect was observed on the sample using SmAFLC comparing to nematic LC based nano-PDLCs. (193 words/ 200 words)

Evaluating flood risk though numerical simulations in areas where hydrometric and bathymetric data are scarcely available is a challenge. This is however of paramount importance, particularly in urban areas, where huge losses of human life and extensive damage can occur. This paper focuses on the June 2-3, 2023 event at Léogâne in Haiti, where the Rouyonne River partly flooded the city. Water depths in the river were recorded since April 2022 and a few discharges were measured manually but it was not sufficient to produce a reliable rating curve. Using a uniform flow assumption combined with the BaRatin method (Bayesian rating curve), it was possible to extrapolate the existing data to higher discharges. From there, a rainfall-runoff relation was developed for the site using the AtHyS distributed hydrological model, which allowed to determine the discharge of the June 2023 event, which was estimated as twice the maximum conveying capacity of the river in the measurement section. Bathymetric data were obtained using drone-based photogrammetry and two-dimensional simulations were carried out using the WATLAB computational environment to represent the flooded area and the associated water depths. By comparing the water depths of 21 measured high-water marks with the simulation results, we obtain KGE and NSE criteria of, respectively, 0.890 and 0.882. This allows us to conclude that the model is sufficiently accurate and could be used by flood managers and decision-makers to assess flood risk and vulnerability in Haiti.

Significant amount of oil remains in the reservoir after primary and secondary operations and to recover the remaining oil, enhanced oil recovery (EOR) can be applied as one of the feasible options remaining nowadays. In this study new nano polymeric materials have been prepared from purple yam and cassava starches. The yield of purple yam nanoparticles (PYNPs) was 85% and that of cassava nanoparticles (CSNPs) is 90.53%. Synthesized materials were characterized through particle size distribution (PSA), zeta potential distribution, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The performance of PYNPs in recovering oil was better than CSNPs as found from recovery experiments. Zeta potential distribution results confirmed the stability of PYNPs over CSNPs (-36.3 mV for PYNPs and -10.7 mV for CSNPs). The optimum concentration for these nanoparticles has been found from interfacial tension measurements and rheological properties and it was 0.60 wt.% for PYNPs and 0.80 wt.% for CSNPs. More incremental recovery (33.46%) has achieved for the polymer that contained PYNPs in comparison to the other nano-polymer (31.3%). This opens the inception for a new technology for polymer flooding that may replace the conventional method that depends on partially hydrolyzed polyacrylamide (HPAM).

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

Cross-linked polyethylene (XLPE) is a highly all-important material renowned for its exceptional physical and chemical properties, and it is extensively utilized in various industries such as con-struction, piping, cable insulation and medical equipment. The cross-linking process of polyethylene involves chemical or physical bonding of polymer chains to enhance its resistance to heat, chemicals and mechanical stress. This study offers a comprehensive overview of recent research and potential advancements in this field, with a particular focus on the development of efficient techniques and environmentally sustainable cross-linking systems. It evaluates the opportunities and challenges faced by cross-linked polyethylene materials across diverse applications, providing valuable insights for future research in this area.

Hydrogels prepared from natural polymer have attracted extensive attentions in biomedical fields such as drug delivery, wound healing, and regenerative medicine due to their good biocompatibility, degradability and flexibility. This review outlines the commonly used natural polymer in hydrogel preparation, including cellulose, chitosan, collagen/gelatin, alginate, hyaluronic acid and starch. The polymeric structure and process/synthesis of natural polymers are illustrated, and natural polymer-based hydrogels including the hydrogel formation and properties are elaborated. Subsequently, the biomedical application of hydrogels based on natural polymer in drug delivery, tissue regeneration, wound healing and other biomedical field is summarized. Finally, the future perspectives of natural polymers and hydrogels based on them are discussed. For natural polymer, novel technologies such as enzymatic and biological methods are developed to improve the structural properties and the development of new natural based polymers or natural polymer derivatives with high performance is still very important and challenging. For natural polymer-based hydrogels, novel hydrogel materials, like double-network hydrogel, multifunctional composite hydrogels and hydrogel microrobots are designed to meet the advanced requirements in biomedical application, and new strategies such as dual-crosslinking, microfluidic chip, micropatterning and 3D/4D bioprinting, have been explored to fabricate advanced hydrogel materials with designed properties for biomedical application. Overall, natural polymeric hydrogels have attracted increasing interests in biomedical application, and the development of novel natural polymer-based materials and new strategies/methods for hydrogel fabrication is badly desirable and still challenging.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Sea level rise due to global warming is a continuing and, disappointingly, accelerating process, which has already affected and will further impact coastal lowlands and the social and economic activities in these areas. Delos Island, situated in the middle of the Cyclades in the Aegean Sea, was considered the most sacred of all islands in ancient Greek culture and a trading hub for the entire eastern Mediterranean. Uninhabited since the 7th century AD, and consistently the focus of research and touristic attention, the island is designated as an archaeological site and inscribed on the Unesco World Heritage List. Previous studies on the relative sea level (rsl) changes suggest a steadily rsl rise during the last 6,300 years, starting from a sea level at -4.80±0.20m in the Late Neolithic. The seafront of the ancient city of Delos is subject to the effects of the rsl rise, which have caused significant coastline retreat and exposure to the northerly winds and waves, whereas parts of the coastal lowland where the remains of the ancient city lie are inundated, forming extended wetlands. The future impacts of rsl rise on the seafront of ancient Delos are illustrated on very high-resolution digital surface models, evaluating both the flooding risk under different climatic projections, as provided by the IPCC AR6 report, and the ongoing land subsidence, as recorded by GNSS data. An rsl rise ranging from 87cm (SSP1-2.6 scenario) to 148cm (SSP5-8.5 scenario) is anticipated by 2150, requiring both resilience strategies and adaptation solutions as well as mitigation policies to cope with the effects of climate change.

Computational fluid dynamics (CFD) modeling has emerged as a valuable tool for investigating complex processes like microencapsulation. This paper aims to validate the ability of CFD simulations to predict particle size distribution in a polymer microencapsulation process. The CFD modeling approach employed an Eulerian multiphase framework, incorporating a discrete population balance model to track the evolution of the droplet population. A realizable k-ε turbulence model and a multiple reference frame strategy were utilized to capture the system’s flow dynamics. The results reveal that while the CFD simulations align well with experimental data at higher agitation speeds (>10000 rpm), discrepancies arise at lower speeds (<7500 rpm), indicating a challenge in accurately capturing turbulent viscous regimes. Despite these challenges, the CFD model demonstrates robust predictive capabilities for droplet formation and distribution in microencapsulation processes, validated by error margins within acceptable limits. The validated model can be used as a reliable tool to guide experimental efforts and optimize process parameters, contributing to an enhanced understanding and control of microencapsulation processes.

CO2 flooding stands as a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in its oil recovery, yet a comprehensive quantitative analysis remains an area in need of refinement. In this study, we have developed 1D and 2D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly-miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns are determined. A novel approach of the contour area calculation method is introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding geological parameters, oil viscosity, and injection-production parameters. Furthermore, the Random Forest (RF) algorithm is employed to identify the controlling factor of the sweep coefficient, as determined by out-of-bag (OOB) data displacement analysis. The results show that the miscible front is located at the point of maximum CO2 content in the oil phase. The immiscible front occurs at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moves at a faster rate compared to the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impact the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibits the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio is a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection-production parameters also play a pivotal role in sweep coefficient. Decreased well spacing and increased gas injection rates are found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates can improve the miscibility degree of partly-miscible flooding from 0.69 to 1.0. Oil viscosity proves to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly-miscible flooding patterns. Conversely, gravity segregation primarily governs the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerges as a paramount influence, with a factor importance value (FI) reaching 1.04. these results provide a theoretical foundation for the application of CO2 flooding, enhancing the understanding of the critical factors governing its success.

River renaturation can be an effective management method for restoring the floodplain's natural capacity and minimizing the effects during high flow periods. A 1D-2D HEC-RAS model, in which the flood plain was considered as 2D and the main channel as 1D, was used to simulate flooding in the restored reach of the Spree River. When computing in this model, finite volume and finite difference approximations using the Preissmann approach are used for the 1D and 2D models, respectively. To comprehend the sensitivity of the parameters and model, several scenarios were simulated using different time steps and grid sizes. Additionally, dykes, dredging, and changes to the vegetation pattern have been used to simulate flood mitigation measures. The model predicted that flooding would occur mostly in the downstream portion of the channel in the majority of the scenarios without mitigation measures, whereas with mitigation measures, flooding in the floodplain would be greatly reduced. By preserving the natural balance on the channel's floodplain, the restored area needs to be kept in good condition. Therefore, mitigating measures that balance the area's economic and environmental aspects must be considered in light of the potential for floods.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Due to the growing interest in biopolymers, biosynthesizable and biodegradable polymers currently occupy a special place. Unfortunately, the properties of native biopolymers are not satisfactory, which explain that attempts are being made to modify them. The work attempts to improve the properties of poly(3-hydroxybutyrate) (P3HB) using linear aliphatic polyurethane (PU) based on 1,4-butanediol and hexamethylene 1,6-diisocyanate. The conducted studies on the effect of the amount of PU used (5, 10, 15 and 20 wt.%) showed an improvement in the thermal properties of the prepared polymer blends. There was an increase in the degradation temperature of the ob-tained blends in relation to the native P3HB by 12-57C, and the difference between the melting point and the degradation point was above 100°C for most of the obtained blends. As part of the tested mechanical properties of the new polymer blends, we noted the desired increase in the tensile strength, in the relative elongation at break and in the impact strength with a decrease in hardness, in particular with the presence of 5 wt.% PU. Therefore, for further improvement, hybrid nanobiocomposites with 5 wt.% PU and organically modified montmorillonite (MMT – Cloisite 30B) were produced. The nanoadditive was used in typical amount of 1-3 wt.%. The nanostructure of the biocomposites produced by extrusion was examined by small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM), the morphology by scanning electron microscopy (SEM), and compatibility by infrared spectroscopy (FT IR). In addition, selected mechanical properties were determined and thermal properties were tested by the thermogravimetric analysis (TGA) and the standard differential scanning calorimetry (DSC). The polyester and polyurethane chains penetrated into the interlayer spaces of organically modi-fied nanoclay – Cloisite30B and the complete delamination occurred during direct mixing in the extrusion process. FT IR spectral analysis showed the compatibility of the polymer biocomposite components by the coexistence of intermolecular interactions in the form of hydrogen bonds. The morphology studies of the produced hybrid nanobiocomposites showed an interaction of the bi-opolymer matrix with PU and Cloisite30B and the formation of easily migrating polyester-polyurethane-montmorillonite adducts, which resulted in improved mechanical properties com-pared to the properties of the native P3HB and P3HB-PU compositions. The influence of the presence of a nanofiller on the properties of the prepared nanobiocomposites was tested and it was found that, as expected, the smallest amount of nanofiller provides the best results.It was found that the obtained nanobiocomposites containing the smallest amount of nano-fillers, i.e. 1 wt.% Cloisite30B exhibited the best mechanical and thermal properties. The desired decrease in hardness by 15% and a higher value of impact strength by 15%, an increase in elonga-tion at break by 60% and an increase in thermal stability of the newly produced biocomposites compared to to the native P3HB were observed. The prepared nanobiocomposites combined the best features caused by the elasticizing effect of polyurethane and the formation of P3HB-PU-MMT adducts.

The graphene based highly conductive and flexible devices has received momentous attraction and growth in recent years for potential multifunctional uses. The development of flexible and washable textile sensors, actuators, energy storage and energy harvesting systems. Textile fabrics coated with graphene and conductive polymers have been used for wearable self-powered e-textiles, such as tribo-electric, piezoelectric, and Thermoelectric. Herein this research, 100% woven cotton fabric is Fictionalized with graphene oxide (GO) using industrial-scale cold pad batch dyeing technique for the development of low-grade body heat into self-powered wearable e-textiles. The conductive polymer PEDOT: PSS was coated using layer by layer approach. The study demonstrates that the resultant textile electrodes showed reduced electrical sheet resistance from 2.5 MΩ to 15KΩ, with a reduced graphene oxide and further reduced to (2.5 -12.5 Ω) for conductive polymer. The sheet resistance was decreased with the number of dyeing cycles (10-15) and increased with 20 washing cycles vice versa. The study demonstrates that the sensor response and performance were improved with increasing the content percent of rGO and PEDOT: PSS. The tensile strength of as coated fabric electrodes was improved from (25.0-85.5 mPa) and fabric thickness was increased to (26-38µm) without compromising or influencing the air permeability. The resultant textile electrodes may potentially be used in smart textiles for self-powered flexible wearable generators, sensors, and energy storage. The study demonstrates that the cold pad batch dyeing method is a suitable and effective method for the fabrication of graphene-based textiles.

The risk related to embankment dam breaches needs to be evaluated in order to prepare emergency action plans. The physical and hydrodynamic parameters of the flood wave generated from dam-failure event correspond to various breach parameters such as width, slope and formation time. This study aimed to simulate dam-breach failure scenario of Yabous dam (NE Algeria) and analyze its influence on areas (urban and natural environments) downstream the dam. The simulation was completed using the sensitivity analysis method in order to assess the impact of breach parameters on the dam-break scenario. The propagation of flood wave associated to dam-break was simulated using the one-dimensional HEC-RAS hydraulic model. This study ap-plied a sensitivity analysis of three breach parameters (slope, width, and formation time) in five sites selected downstream the embankment dam. The simulation showed that the maximum flow of the flood wave recorded at the level of the breach was 8768 m3/s, which gradually attenuated along the river course to reach 1579.2m3/s at about 8.5km downstream the dam. This study estab-lished the map of flood-prone areas that illustrated zones threatened with the flooding wave trig-gered by the dam failure due to extreme rainfall events. The sensitivity analysis showed that flood wave flow, height and width revealed positive and similar changes for the increase in adjustments (±25% and ±50%) of breach width and slope in the 5 sites. However, flood wave parameters of breach formation time showed significant trends that changed in the opposite direction compared to breach slope and width.

The article presents the results of a morpho-physiological assessment of rice samples by the strength of growth, as well as an assessment of the degree of development of the conducting system of the flag leaves of rice plants. The resistance of varieties to flooding is very relevant in the fight against weeds due to the deep layer of water that weeds cannot overcome. Currently, there are no zoned varieties in Russia that would meet these requirements. Therefore, the problem of creating such rice varieties is urgent, as it will reduce production costs, reduce grain losses during harvesting, improve the quality of the products obtained, and also reduce the pesticide load on the ecosystem. As a result of research, a number of studied samples revealed the potential to quickly lengthen the first leaves, overcome a large layer of water and accumulate vegetative mass. As a result of the evaluation of the conducting system of the flag leaf of rice plants, it was found that in plants with the flood resistance gene Sub1A, which stops growth under water, the conductive beams were smaller in comparison with other fast-growing samples with the AG, Sk genes. Consequently, fast-growing samples have bigger sizes of the conducting system as a resistance mechanism.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

Polyethylene terephthalate (PET) is one of the most produced plastic materials in the world. The emer-gence of microplastics and nanoplastics (MPs/NPs) as a significant environmental contaminant has become a matter of increasing concern. While the toxicological effects of PET NPs have been widely re-searched, there is a lack of methodologies for studying their accumulation. The present study introduces a novel method to monitor the distribution of PET NPs in germinating wheat (Triticum aestivum L.) seeds. This involves the functionalization of superparamagnetic iron oxide nanoparticles (SPIONs) with PET NPs (PET-fSPION) coupled with magnetic resonance microimaging (µMRI) to provide insight into their distribution within the seed. The present study has demonstrated that PET-fSPION accumulates in specific regions of germinating wheat seeds, including the shoot apical meristem, the radicle, the cole-optile, the plumule, and the scutellum. Furthermore, the accumulation of PET-fSPION has been shown to exert a discernible effect on spin-spin relaxation, as observed via MRI and quantitative T2 relaxation time analysis. The accumulation of PET NPs in embryo regions was also confirmed by SEM. Diffu-sion-weighted magnetic resonance imaging (DW-MRI) and non-invasive chemical shift imaging analyses demonstrated that PET NPs resulted in restricted diffusion within the highlighted areas, as well as an impact on lipid content. Our study reveals that using µMRI with fSPION provides a non-invasive method to monitor the biodistribution of PET nanoparticles in wheat seeds. Additionally, it offers valuable in-sights into the microstructural interactions of PET.

In today's context of rising sea levels and subsiding land topography, coastal flooding is a major concern for coastal areas, both nationally, regionally, and internationally. A detailed understanding of these two phenomena is a prerequisite for effective coastal flood management. The main objective of the present study is to contribute to the understanding of the impact of subsidence and sea-level rise on coastal flooding in Saint-Louis, and in particular the Langue de Barbarie, by producing a vulnerability map of submerged surfaces. To this end, the Synthetic Aperture Radar (SAR) interferometry technique is used to process a time series of Sentinel-1 images and estimate land subsidence in the Saint-Louis and Langue de Barbarie area. Interferometric SAR (InSAR) measurements are merged with RCP 2.6 sea-level rise scenarios to identify predicted flooded areas and provide a flood vulnerability map. At the Langue de Barbarie, topographic subsidence is estimated at between -6.4 and -0.4mm/year. In this study, we show that local land subsidence may increase vulnerability to flooding caused by sea-level rise based on 2100 projections. This may represent an increase in the flood zone in the study area. Based on the RCP 2.6 scenario and the subsidence rates obtained, a significant part of the St. Louis coastline and city would be subject to coastal and fluvial flooding for the years 2040 and 2100. For these dates, 29 to and 36 Km2 of the studied area would be occupied by water. Given this situation, research in Saint-Louis needs to focus on adaptation scenarios to coastal risks, to protect coastal communities and safeguard the city's historical heritage.

Sinkhole flooding is an essential hydrological process to recharge karst aquifer in arid to dry sub-humid regions. On the other hand, the increase of rain extremes is one of the major consequences of the global warming, together with the expansion of drylands. Thus, appropriate runoff regulation in endorheic karst basins in order to reduce the risk of flooding and improve the quantity and quality of the water drained by sinkholes will be more and more crucial. With these premises, a systematic review was performed by using WoS engine to infer the best practices for the karst water management in regions actually or potentially affected by water scarcity. Hydrological models are essential to manage the consequences of climate change on karst water resource, however the review shows that providing the tools necessary for reliable modeling is still challenging. Finally, due to the intrinsic vulnerability of the karst aquifers, pollution reduction and wastewater recycling policy will play key role in the next decades.

This article raise a topic of critical examination of polypropylene, a key polymeric material, and its extensive application within the automotive industry, particularly focusing on the manufacturing of brake fluid reservoirs. The study aims to enhance the understanding of polypropylene's behavior under mechanical stresses through a series of laboratory destruction tests and numerical simulations, emphasizing the Finite Element Method (FEM). A novel aspect of this research is the introduction of the PEAK parameter, a groundbreaking approach designed to assess the material's resilience against varying states of strain, known as triaxiality. This parameter facilitates the identification of critical areas prone to crack initiation, thereby enabling the optimization of component design with a minimized safety margin, which is crucial for cost-effective production. The methodology involves conducting burst tests to locate crack initiation sites, followed by FEM simulations to determine the PEAK threshold value for the Sabic 83MF10 polypropylene material. The study successfully validates the predictive capability of the PEAK parameter, demonstrating a high correlation between simulated results and actual laboratory tests. This validation underscores the potential of the PEAK parameter as a predictive tool for enhancing the reliability and safety of polypropylene automotive components. The research presented in this article contributes significantly to the field of material science and engineering by providing a deeper insight into the mechanical behavior of polypropylene and introducing an effective tool for predicting crack initiation in automotive components. The findings hold promise for advancing the design and manufacturing processes in the automotive industry, with potential applications extending to other sectors.

The effects of global warming combined with the progressive expansion of urbanization have considerably increased exposure to urban flooding and runoff widespread erosion risk, also causing shallow landslides and mud flows, respectively in urbanized areas of lowland and hill/foothill environments. Increasing urban flooding resilience has become a priority at virtually all levels of governance. The analysis of a different hazard scenarios, in which various hydro-meteorological conditions and management alternatives are examined, should act as the basis for the effective design and evaluation of interventions to improve urban flooding resilience. Turin Metropolitan Area (TMA), located in north-western Italy, represents a unique case due to its complex orography, with a mountainous sector in the west side and a flat or hilly part in the east side. During the warm season, these environmental conditions make the urban area prone to severe atmospheric convection causing frequent hailstorms and rainstorms of high intensity that may impact on urban infrastructures (i.e., drainage system and road network), thus requiring an adequate management as a key factor to reducing risk and losses. The urban areas of TMA are monitored by polarimetric Doppler weather radars and by a dense rain gauges network. Analyzing several case studies of urban flooding, this research work assesses the feasibility of a meteorological radar early warning system based on the identification of rainfall thresholds that characterize urban flooding, occurring in the lowlands, and the runoff erosion phenomena affecting the urbanized hills and foothills.

Downpours are increasing in frequency and severity due to climate change. Cities are particularly susceptible to downpours because of their large share of impervious surfaces. Minimising pluvial flood risk requires all involved stakeholders to collaborate and overcome probable barriers. Simultaneously, an increase in citizen engagement in climate adaptation is preferred, whereas experiences with inclusive decision-making are still limited. The aim of this paper is to obtain a deeper understanding of how the capacity to govern pluvial flood risk can be developed through citizen engagement. We scrutinised the capacity of local actors to govern pluvial flood risk in the city of Utrecht, the Netherlands. For the analysis of Utrecht’s problem-solving capacity, the Governance Capacity Framework provided a consistent assessment of governance components. The results indicate that Utrecht’s capacity to govern pluvial flooding is relatively well-developed. Collaboration between public authorities is advanced, sufficient financial resources are available and smart monitoring enables high levels of evaluation and learning. However, citizen awareness and engagement in policy making is rather low. Accordingly, citizens’ willingness to pay for flood adaptation is limited. Stimulating flood risk awareness by combining financial incentives with more advanced arrangements for active citizen engagement is key for Utrecht and other cities.

The field of polymer additive manufacturing (AM) has experienced rapid evolution, marked by significant advancements in materials science and technology. This paper reviews recent innovations in polymer materials tailored for additive manufacturing processes, focusing on enhancements in mechanical properties, functionalization, and processability. Key developments include the introduction of high-performance thermoplastics, composite materials incorporating fibers or nanoparticles, and novel photocurable resins. These materials offer improved strength, durability, and versatility compared to traditional polymers. Furthermore, research into bio-based and recyclable polymers highlights a growing trend towards sustainable manufacturing practices. Advances in material formulations, including self-healing and shape-memory polymers, are also examined for their potential to transform applications across various industries. This review synthesizes current research trends and provides a comprehensive overview of the state-of-the-art in polymer AM materials, emphasizing the impact of these innovations on the future of manufacturing technologies.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p&lt;0.05; p&lt;0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p&lt;0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

Abstract: Conventional antibiotic and multidrug treatments become less and less effective and a discovery of new effective and safe antibacterial agents got a global priority. The returning to the natural antibacterial product is relatively new current trend. Terrestrial biota is a rich source of biologically active substances whose antibacterial potential was not fully utilized. Aim of this review is to present the current state-of-the art of terrestrial biota-derived antibacterial agents and inspired by nature treatments. It is a summary of the most important sources and new identified or modified antibacterial agents and treatments during the last 5 years. It focuses on the significance of plants- animals- and bacteria-derived biologically active agents as powerful alternatives to antibiotics as well as on the advantages of utilizing natural antibacterial molecules alone or in combinations with antibiotics. The main conclusion is that the terrestrial biota derived antibacterial products and substances open variety of new ways to modern improved therapeutic strategies. New terrestrial sources of known antibacterial agents and new antibacterial agents from terrestrial biota were discovered during the last 5 years, which are under investigation together with some long ago known but now surviving their renaissance for the development of new medical treatments. Use of natural antibacterial peptides as well as combinational therapy by commercial antibiotics and natural products outlines as the most promising for treating of bacterial infections. In vivo testing and clinical trials are necessary to reach clinical application.

The storm 'Daniel' has caused the most severe flood phenomenon that Greece has ever experienced, with thousands of hectares of farmland submerged for days. This led to sediment deposition in the inundated areas, which significantly altered the chemical properties of the soil, as revealed by extensive soil sampling and laboratory analysis. Causal relationships between soil chemical properties and sediment deposition were extracted using the DirectLiNGAM algorithm. Results of causality analysis showed that the sediment deposition affected the CaCO3 concentration in the soil. Also, causal relationships were identified between CaCO3 and available phosphorus (P-Olsen), as well as between sediment deposit depth and available manganese. The quantified relationships between the soil variables were then used to generate data using a Multiple Linear Perceptron (MLP) regressor for various levels of deposit depth (0, 5, 10, 15, 20, 25 and 30 cm). Then linear regression equations were fitted across the different levels of deposit depth to determine the effect of deposit depth on CaCO3, P, and Mn. The results show that there is a linear slope of 0.12, -0.16, and 0.13, for CaCO3, P, and Mn with deposit depth, respectively. Statistical analysis indicates that corn growing in soils with sediment over 10 cm requires a 31.8% increase in P rate to prevent yield decline. Additional notifications regarding cropping strategies in the near future are also discussed.

In order to explore the effect of fertilization patterns on the growth of rapeseed seedlings under waterlogging stress, three fertilization patterns (conventional fertilization, supplemental organic fertilization, and supplemental microbial fertilization) were set up using the variety Xiangyou 708 as the material, and waterlogging treatment was carried out during the seedling stage of rapeseed. The effects of fertilization patterns on the growth of rapeseed seedlings and rhizosphere microorganisms under waterlogging stress were investigated. The results showed that all three fertilization patterns exhibited that waterlogging stress inhibited the growth of rapeseed seedlings, inhibited root activity, and changed the structure of rhizosphere bacterial colonies. However, supplemental organic fertilization and microbial fertilization could better promote the growth of rapeseed seedlings, reduce the impact of waterlogging stress on the growth of rapeseed seedlings, and accelerate the recovery of rapeseed seedlings after waterlogging stress. In addition, supplemental microbial fertilization could also change the structure of rhizosphere bacterial colonies. Under normal water supply, supplemental organic fertilization enriched P_Bacteroidota, P_Actinobacteriota, P_Chloroflexi, and G_Flavisolibacter in the rhizosphere soil of rapeseed, while supplemental microbial fertilization enriched P_Bacteroidota and G_Flavisolibacter in the rhizosphere soil of rapeseed. After 7 days of waterlogging treatment, supplemental organic fertilization enriched P_Verrucomicrobiota in the rhizosphere soil of rapeseed, while supplemental microbial fertilization enriched P_Actinobacteriota, G_SC-I-84, and G_Ellin6067 in the rhizosphere soil of rapeseed. The enrichment of these bacteria may be related to the growth promotion and waterlogging tolerance of rapeseed. This study provides evidence that microbial fertilizer and organic fertilizer can promote the growth of rapeseed and enhance its waterlogging tolerance, as well as evidence that some rhizosphere microorganisms have a potential role in promoting the growth and waterlogging tolerance of rapeseed.

Polymer hydrogels are 3D networks consisting of hydrophilic crosslinked macromolecular chains, able to swell and retain water. Since their invention in the 1960s, they have become an outstanding pillar in the design, development, and application of engineered polymer systems suitable for biomedical and pharmaceutical applications (such as drug or cell delivery, regeneration of hard and soft tissues, wound healing, and bleeding prevention, among others). Despite several well-established synthetic routes of polymer hydrogels based on batch polymerization techniques, about fifteen years ago academia started to look for alternative methods involving simpler reaction paths, shorter reaction times, and lower energy consumption. In this context, frontal polymerization (FP) undoubtedly has become an alternative and efficient reaction model that allows for converting monomers into polymers via a localized and propagating reaction, by exploiting the formation and propagation of a “hot” polymerization front, able to self-sustain and propagate throughout the monomeric mixture. Therefore, the present work aims to summarize the main research outcomes, achieved during the last years, concerning the design, preparation, and application of FP-derived polymeric hydrogels, demonstrating the feasibility of this technique for the obtainment of functional 3D networks, and providing the reader with some perspectives for the forthcoming years.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

Metal-reinforced polymethyl-methacrylate (PMMA) is considered the gold standard material for immediate loading on dental implants. However, mechanical problems under loading cycles can occur, such as fractures. To overcome these drawbacks, a novel polymer-based material has been proposed. The aim of the present in vitro comparative research is to validate a novel composite polymer developed to replace metal-reinforced PMMA interim restoration due to its advantages of good mechanical proprieties, easier manufacturing, and handling. Ten interim restorations were CAD/CAM designed and fabricated (five in the composite "ONLY" group, and five in the metal-reinforced PMMA group). All the samples were screwed into the prototype models, simulating a complete edentulous mandible rehabilitated with six straight implants. Outcome measures were breakpoint (load, N) and displacement (mm) thought a static, compression test and material behavior under dynamic cyclic test method (fatigue test). A total of twenty samples were tested. Ten samples were used for each test (10 for static and 10 for dynamic), five samples were used in each group (test and control). All the specimens completed the mechanical tests, as planned. There was no statistically significant difference between groups for all, breakpoint, displacement and fatigue tests. Breakpoint in the test group was 1953.19 ± 543.73 N, while, it was 2031.10 ± 716.68 N in the control group, with no statistically significant difference (P=0.775). The displacement was 1.89 ± 0.34 mm in the test group and 1.98 ± 0.75 mm in the control group, again, with no statistically significant difference (P=0.763). Under dynamic cyclic test method, in the control group the mean load was 2504.6 ± 972.15 N, while, in the test group the mean load was 3382 ± 578.5 N. The difference between group was 877.4 ± 579.3 N (p value=0.121). With the limitation of this in vitro study, the novel composite polymer can be used to immediately load dental implants. Further clinical researches are needed to confirm this preliminary results.

This study assesses coastal flooding extension mapping based on two innovative approaches. The first is based on the coupling of two robust numerical models (SWASH and LISFLOOD), in this case, discharges were extracted from the wave overtopping results from SWASH 1D and set as boundary conditions for LISFLOOD on the crest of an existing seawall where overtopping typically occurs. The second, hereby called the ‘Tilted Bathtub Approach’ (TBTA), is based on wave run-up levels and buffering the affected area of a prior flooding event, adjusting it for expected sea-states according to different return periods. The proposed approaches are applied to a case study on the Northern Portuguese coast, at Furadouro beach, in the municipality of Ovar, which has been facing multiple flooding episodes throughout recent years, including a dramatic storm in February 2014. This event was used as validation for the proposed methods. A 30 years long hourly local wave climate time series was used both to perform an extreme value analysis in order to obtain expected sea-states according to different return periods, and also for performing a sensitivity test for established empirical formulas to estimate wave run-up at this particular case. Results indicate both approaches are valuable: they yield coherent flood extension predictions that align well with the real inundated area from the 2014 storm. The convergence of these findings underscores the potential for these methods in future coastal flood risk assessment and planning.

The interaction between oceanographic, meteorological, and hydrological factors can result in an extreme flooding scenario in the low-lying coastal area, called compound flooding (CF) events. For instance, rainfall and storm surge (or high river discharge) can be driven by the same meteorological, tropical or extra-tropical cyclones, resulting in a CF phenomenon. The trivariate distributional framework can significantly explain compound events' statistical behaviour reducing the associated high-impact flood risk. Resolving heterogenous dependency of the multidimensional CF events by incorporating traditional 3-D symmetric or fully nested Archimedean copula is quite complex. The main challenge is to preserve all lower-level dependencies. An approach based on decomposing the full multivariate density into simple local building blocks via conditional independence called vine or pair-copulas is a much more comprehensive way of approximating the trivariate flood dependence structure. In this study, a parametric vine copula of a drawable (D-vine) structure is introduced in the trivariate modelling of flooding events with 46 years of observations of the west Coast of Canada. This trivariate framework searches dependency by combining the joint impact of annual maximum 24-hr rainfall and the highest storm surge and river discharge observed within the time ±1 day of the highest rainfall event. The D-vine structures are constructed in three alternative ways by permutation of the conditioning variables. The most appropriate D-vine structure is selected using the fitness test statistics and estimating trivariate joint and conditional joint return periods. The investigation confirms that the D-vine copula can effectively define the compound phenomenon's dependency. The failure probability (FP) method is also adopted in assessing the trivariate hydrologic risk. It is observed that hydrologic events defined in the trivariate case produce higher FP than in the bivariate (or univariate) case. It is also concluded that hydrologic risk increases (i) with an increase in the service design life of the hydraulic facilities and (ii) with a decrease in return periods.

AbstractLocal estimates of coastal flood risk are required for coastal planning and development, including the location and design of sea-defences and coastal buildings, such as harbours and associated infrastructure. This paper discusses the use of three parameters associated with estimating such risks; the flood return period, the instantaneous flood probability and the flood design risk, and it describes the mathematical background for their derivation. The discussion is extended to include the effects of sea level rise and how it can be incorporated into the calculations. Flood height can vary quite rapidly with distance along the coast, being affected by coastal topology, which may magnify or diminish the tidal and surge effects. Similarly land heave influences the local effects of sea level rise and can be influenced by water extraction, tectonic movements and melting ice. Tide gauge measurements provide a local historical record from which the various parameters can be retrieved. This paper discusses the algorithms used to derive these measures from tide-gauge records. The figures have been derived for four tide gauges located on the UK east coast.

Previous reviews by the authors [1, 2] indicate the continuing development and improvement of thermal protective systems through the introduction of polymer nanocomposites into polymer matrix composites. These materials perform as thermal protective systems for a variety of aerospace applications, such as thermal protection systems (TPS), solid rocket motors (SRM) nozzles, internal insulation of SRM, leading edges of hypersonic vehicles, and missile launch structures. A summary of the most recent, global technical research is presented. Polymeric resin systems continue to emphasize phenolic resins and other materials. New high-temperature organic resins based on phthalonitrile (PN), and polysiloxane are described and extend the increased temperature range of resin matrix systems.

Polymer flooding is one of the most successful chemical EOR methods, and is primarily implemented to accelerate oil production by sweep improvement. However, other benefits have extended the utility of polymers. During the last decade, it has been evaluated for an increasing number of fields, both offshore and onshore. This is a consequence of improved polymer properties, which extends the use to HTHS (high temperature high salinity) conditions and of improved understanding of flow mechanisms such as for heavy oil mobilization. A key issue in understanding polymer performance is to control and predict in-situ porous medium rheology. The first part of this paper reviews recent developments in understanding polymer flow in porous medium. Especially, polymer in-situ rheology and injectivity is discussed. The second part of this paper reports polymer flow experiments using the most applied polymer for EOR processes, HPAM (partially hydrolyzed polyacrylamide). The experiments address high rate near-wellbore behavior (radial flow) as well as reservoir rate steady state flow (linear flow) and discuss differences observed in terms of flow conditions. In addition, impact of oil on polymer rheology was investigated, and compared to single-phase polymer flow in Bentheimer sandstone rock material. Presence of oil leads to a reduction in apparent viscosity.

This study integrated coastal-watershed models and combined a risk assessment method to develop a methodology to investigate the impact resulting from coastal disasters under climate change. The mid-western coast of Taiwan suffering from land subsidence was selected as the demonstrative area for the vulnerability analysis based on prediction of sea level rise (SLR), wave run-up, overtopping, and coastal flooding under the scenarios of 2020 to 2039. Database from tidal gauges and satellite images were used to analyze sea level rise using EEMD (Ensemble Empirical Mode Decomposition). Extreme wave condition and storm surge were estimated by numerical simulation using WWM (Wind Wave Model) and POM (Princeton Ocean Model). Coastal inundation was then simulated via WASH123D watershed model. The risk map of study areas based on the analyses of vulnerability and disaster were established using the AHP (Analytic Hierarchy Process) technique. Predictions of sea level rise, the maximum wave condition and storm surge under the scenarios of 2020 to 2039 are presented. The results indicate that the sea level at the mid-western coast of Taiwan will rise in an average of 5.8 cm, equivalent to a rising velocity of 2.8 mm/year. The analysis indicates that Wuqi, Lukang, Mailiao, and Taixi townships are susceptive, low resistant and low resilient, and reaches the high risk level. The assessment provides that important information for making adaption policy in the mid-western coast of Taiwan.

Water pollution associated with flooding is one of the major problems in cities in the global South. However, studies of water quality dynamics during flood events are not often reported in literature, probably due to difficult conditions for sampling during flood events. Water quality parameters in open water (canals, rivers, and lakes), floodwater on roads and water in sewers have been monitored during the extreme fluvial flood event on 7 October 2013 in Can Tho city, Vietnam. This is the pioneering study of urban flood water pollution in real time in Vietnam. The results showed that water quality is very dynamic during flooding, especially at the beginning of the event. In addition, it was observed that the pathogen and contaminant levels in the floodwater are almost as high as in sewers. The findings show that population exposed to flood water runs a health risk that is nearly equal to that of being in contact with sewer water. Therefore the people of Can Tho not only face physical risk due to flooding, but also exposed to health risk.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

Carbon nanodots (CNDs) have garnered significant attention as viable drug delivery vehicles in recent years, especially in the field of phytomedicine. Although there is much promise for therapeutic applications with phytomedicine, its effectiveness is frequently restricted by its low solubility, stability, and bioavailability. This paper offers a thorough synopsis of the developing field of phytomedicine drug delivery based on CND. It explores CND synthesis processes, surface functionalization strategies, and structural and optical characteristics. Additionally, the advantages and difficulties of phytomedicine are examined, with a focus on the contribution of drug delivery methods to the increased effectiveness of phytomedicine. The applications of CNDs in drug delivery are also included in the review, along with the mechanisms that underlie their improved drug delivery capabilities. Additionally, it looks at controlled release methods, stability augmentation, and phytomedicine loading tactics onto CNDs. The potential of polymeric carbon nanodots in drug delivery is also covered, along with difficulties and prospective directions going forward, such as resolving toxicity and biocompatibility issues. In summary, the present review highlights the encouraging contribution of CNDs to the field of drug delivery, specifically in enhancing the potential of phytomedicine for therapeutic purposes.

Fatigue performance and self-repairing activity of asphalt binders are two properties that highly influence the fatigue cracking response of asphalt pavement. There are still numerous gaps of knowledge to fill linked with these two characteristics. For instance, current parameters fail to fully accommodate these two bitumen phenomena. This study aims to propose a new procedure to address this issue utilizing the linear amplitude sweep (LAS) test, LAS with rest period (RP) (LASH) test, and simplified viscoelastic continuum damage (S-VECD) model. This research work used four different types of asphalt binders: neat asphalt (NA), self-healing thermoplastic polyurethane (STPU)-modified bitumen (STPB), self-healing poly (dimethyl siloxane) crosslinked with urea bond (IPA1w)-modified bitumen (IPAB), and styrene–butadiene–styrene (SBS)-modified bitumen (SBSB). Before the testing process, all the materials were subjected to short-term and long-term aging. The new procedure showed a superior capacity to analyze and accommodate all bitumen fatigue performances and self-repairing activities compared to the current method. Another finding proved that asphalt binders with higher self-restoration behavior failed to show better fatigue performance. A breakthrough finding demonstrated that asphalt binder fatigue response augmented when the RP was applied at a higher damage intensity (S) value. STPBs and IPABs reached their highest increments of fatigue response, containing 1.0% of STPU and 0.5% of IPA1w, respectively. Those augmentations were 207.54% and 232.64%, respectively.

Polyvinyl alcohol (PVA) is highly compatible polymer with biological environments. Specifically, it has been used as a trap for different types of microorganisms in Bio-MEMS, and its properties can be modified to act as an electrode for electrochemical analysis. This study presents a nano-composite developed with PVA, multiwall carbon nanotubes (CNTs) doped with nitrogen, which changes the electrical properties of the polymer and its viscosity to obtain nanofibers by electro-spinning. The proposed nanocomposite was characterized using Fourier transform-infrared and Raman spectroscopy techniques, confirming the presence of the CNTs immersed in the polymer. High-resolution transmission electron microscopy was used to obtain the micrographs that showed the characteristic interplanar distances of the multiwall CNT in the polymeric matrix with values of 3.63 Å. Finally, the CNx mats were exposed to various aqueous solutions in a po-tentiostat to demonstrate the effectiveness of the nanofibers for electrochemical analysis. The CNx-induced changes in the electrical properties of the polymer were identified using cyclic voltammograms, while the electrochemical analysis revealed supercapacitor behavior.

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15%wt) and the sliding regime parameters (load: 1 N, 2.5 N and 5 N, the sliding speed: 0.25 m/s, 0.5 m/s and 0.75 m/s, and the sliding distance: 2500 m, 5000 m and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix.

The escalating demand for multifunctional and advanced materials for growing industries has turned scientific exploration to graphene-based hybrid filler polymer composites. The introduction of graphene with other fillers into polymer matrices results in astonishing properties and thus has gained significant attention in recent years. This study addresses the significance of graphene-based hybrid filler polymer composites in progressive materials science and engineering. The paper encloses some traditional and current preparation techniques employed in the fabrication of composites and a comprehensive review of successfully prepared graphene hybrid polymer composites with enhanced mechanical, thermal, and electrical properties reported in published research. The role of different factors, e.g., filler type, aspect ratios, filler-matrix compatibility, dispersion effects, homogeneity, filler orientation through polymer matrices, and curing conditions, are summarized. Finally, the applications in heavy industries, e.g., aerospace, electronics, energy storage, and automotive sectors were also analyzed. We hope this study will serve as a practical resource for new researchers and practitioners to understand and harness the full potential of these composites in various scientific and industrial fields.

The sudden onset of natural hazards such as a flash flood events can be devastating to a country or region, often affecting numerous communities, and humanitarian supply chains play a major role in enabling the timely recovery of economic and social activities. However, the uncertainty and suddenness of natural disasters such as flash floods, as well as the potential for aftershocks, require humanitarian supply chains to be resilient during the relief process. This research first adopts the Delphi and literature review methods to identify the key indicators in the humanitarian supply chain to form an evaluation index system. Then, taking the 2021 mega-flash flood event which affected four cities in the mountainous region under the jurisdiction of the Zhengzhou municipal government, the ANP method is used to calculate the weights of each indicator and combines the weighted results with the Multi-styling and stereotyping method under Pythagorean fuzzy (PFs-VIKOR) to make an evaluation of the resilience of the humanitarian supply chain in the relief process. The findings suggest that policy makers and decision makers should pay close attention to the coordination of the parties involved in the humanitarian supply chain and improve the level of resilience of the entire supply chain by enhancing the resource scheduling capacity and responsiveness. At the same time, the VIKOR evaluation of the 4 cities highlighted the humanitarian supply chain in Dengfeng City to be most effective in this event due to the close cooperation and positive response of all parties involved in the humanitarian supply chain. The findings of this research provide some useful suggestions and guidance to the various practitioners involved in the humanitarian supply chain. Furthermore, the evaluation of the performance of the four cities in this mega-flash flood event provides some helpful indication of the importance of the various emergency measures which can help to inform policy recommendations for the Zhengzhou municipal government.

The naphtha cracking process results in the production of ethylene, propylene, mixed C4, and pygas, which are all olefins. Distillation columns and cracking furnaces are the primary units of operation. The price of raw materials accounts for 80% of production costs. There is also the pos-sibility of using LPG, a less expensive raw material, in place of some of the naphtha. A change in the raw material will affect the operability of the distillation columns and influence the yield on the cracking side. To determine the best naphtha substitution for LPG without creating a hydraulic problem (Jet Flooding) in distillation columns, analysis utilizing simulation tools must be done. To simulate the substitution of naphtha for other feedstocks, a reliability model is being built by comparing simulation results with data from the actual plant. LPG flow is a free variable that is being used to substitute naphtha. The effects of economically advantageous naphtha substitution for LPG can be assessed with the use of simulation tools without impairing plant operability. Optimum naphtha substitution rate is 21.14% from base case which resulting jet flooding occurred at Propylene Fractionator No 2. By implementing this substitution case, benefit that can be driven $22,772.02/ hour.

This paper is focused on understanding multiscale modelling to obtain a bridge among different time and length scales of simulation techniques. These techniques are vital as it holds the potential to understand and predict the capabilities of polymer nanocomposites (PNCs). However, an appropriate approach in controlling the interfacial interaction between nanoparticle and polymer in nanocomposites structure is still needed to develop. In this review, an initial brief introduction to various trending simulation techniques has been discussed at all three levels of scale (nm, μm, mm). Later, descriptive study on fundamental issues such as thermodynamics, kinetics, mechanical properties, and morphology has been studied deeply. The multiscale modeling bridges the gaps of simulation between the different scales of models from molecular to mesoscale levels working over the broad range of length and timescale. Through the sequential, adaptive, and concurrent approaches, we can develop a system that may comprehend multiscale mode modeling adaptive resolution approach has recently added approach the molecule of the subject can shift their position freely in the domain and through this approach and studied the Brownian motion. Co-The co-current coach is also termed as handshaking path and it is linked aiming at different scale models. Covering the rigid techniques smoothly and linking them at different scales helps in normalizing the statistical behaviour.

Climate change and development have increased urban flooding, requiring modernization of stormwater infrastructure. Retrofitting standard passive systems with controllable valves/pumps is promising, but requires real-time control (RTC). One method of automating RTC is reinforcement learning (RL), a general technique for sequential optimization and control in uncertain environments. The notion is that an RL algorithm can use inputs of real-time flood data and rainfall forecasts to learn a policy for controlling the stormwater infrastructure to minimize measures of flooding. In real-world conditions, rainfall forecasts and other state information, are subject to noise and uncertainty. To account for these characteristics of the problem data, we implemented Deep Deterministic Policy Gradient (DDPG), an RL algorithm that is distinguished by its capability to handle noise in the input data. DDPG implementations were trained and tested against a passive flood control policy. Three primary cases were studied: (i) perfect data, (ii) imperfect rainfall forecasts, and (iii) imperfect water level and forecast data. Rainfall episodes (100) that caused flooding in the passive system were selected from 10 years of observations in Norfolk, Virginia, USA; 85 randomly selected episodes were used for training and the remaining 15 unseen episodes served as test cases. Compared to the passive system, all RL implementations reduced flooding volume by 70.5% on average, and performed within a range of 5%. This suggests that DDPG is robust to noisy input data, which is essential knowledge to advance the real-world applicability of RL for stormwater RTC.

The aim of this research was to undertake laboratory testing to investigate the beneficial effects of epoxy resin grouts on the physical and mechanical properties of sands with a wide range of granulometric characteristics. Six sands, of different particle size and uniformity coefficients, were grouted using epoxy resin solutions with three ratios of epoxy resin to water (3.0, 2.0 and 1.5). A set of unconfined compressive strength tests were conducted on grouted samples at different curing periods and a set of long-term unconfined compressive creep tests in dry and wet conditions after 180 days of curing were also carried out, in order to evaluate the development of the mechanical properties of the sands, as well as, the impact of water on them. The findings of the investigation showed that epoxy resin resulted in appreciable strength values in the specimens, especially those of fine sands, grouted with the different epoxy resin grouts. In general, the compressive strength varied between 0.68 - 5.60 MPa and the modulus of elasticity between 75 - 480 MPa, after a curing period of 180 days. In terms of physical properties, the permeability and porosity (before and after the grouting process) were estimated. Grouts with an epoxy resin to water ratio of 3 decreased permeability by up to four orders of magnitude. Using laboratory results and regression analysis, three mathematical equations were developed that relate each of the dependent variables; compressive strength, elastic modulus, and coefficient of permeability, with particular explanatory variables.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

Chitosan arouses large interest due to its properties and possible applications. Every year the number of publications and patents based on this polymer increases. Chitosan exhibits poor solubility in neutral and basic media limiting its use in such conditions. Another serious obstacle is directly related to its natural origin. Chitosan is not a single polymer with a defined structure but a family of molecules with differences in their composition, size, and monomer distribution. These properties have a fundamental effect on the biological and technological performance of the polymer. Moreover, some of the biological properties claimed are discrete. In this review, we discuss how chitosan chemistry can solve the problems related to its poor solubility and can boost the polymer properties. We focus on some of the main biological properties of chitosan and the relationship with the physicochemical properties of the polymer. Then, we visit two polymer applications related to green processes: the use of chitosan in the green synthesis of metallic na-noparticles and its use as support in biocatalyst. Finally, we briefly describe how making use of the technological properties of chitosan it is possible to develop a variety of systems for drug delivery

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

The evaluation of the possibility of obtaining dihaploids by the method of anther culture in vitro to accelerate selection for resistance to prolonged flooding of seeded rice with water was carried out. The object of research is rice hybrids F2 of the Rice Breeding and Seed Production Laboratory of the “Donskoy” ASC, obtained as a result of interbreeding the best economically valuable varieties with samples bearing genes of resistance to prolonged flooding with water. Basic nutrient medium with an optimal composition of nutrition elements and growth hormones stimulating callo- and morphogenesis were used. For the induction of callus formation, 12604 anthers were planted, according to 26 hybrid combinations represented by 68 plants, as a result, 716 neoplasms were obtained, including 586 non–morphogenic callus, 130 regenerating plants. Cultivation of anthers revealed large genotypic differences in the samples. According to the responsiveness to neoplasms, 60% of the panicles showed a positive result, the rest did not give callus. The most responsive to the formation of callus were hybrid combinations: 5009/2 – 84 pcs., 5010/2 – 94 pcs., 4565/3 – 85 pcs., 4641/2 – 69 pcs. They also showed the ability to morphogenesis. Androgenic plants were obtained by 14 hybrid combinations, their share was 1.03% of the total number of inoculated anthers. 30 green regenerative lines from four rice hybrids were obtained, differing in visual morphological assessment: 5009/2 - 5 pcs., 5010/2 – 5 pcs., 4565/3 – 2 pcs., 4641/2 – 18 pcs. The isolated lines are characterized by good responsiveness in the culture of anthers in vitro, carry genes for resistance to prolonged flooding, and can be used in rice breeding programs using DG technologies.

Groundwater (GW) flooding mechanisms differ from river flooding both spatially and temporally, and preventative methods against groundwater flooding must take this into account. Although groundwater flooding caused by river water rise occurs seldom, it can occasionally become severe and last for a long time if the river is significantly flooded. In the southwest portion of the research domain, Friedrichshafen with a few urban communities, the level of the groundwater table was discovered to be roughly 1 m below the surface. It was discovered that the urban settlement area only has one-story buildings. In the study region, it is typical for the single-story building's foundation bottom level to extend up to a depth of about 1.5 meters. Therefore, flood mitigation methods are taken into account for the southwest portion of the study region. The installation of a pumping well, drainage, and a barrier in the affected area are three different flood control strategies that are taken into consideration for the study area. From a technical and cost-benefit perspective, installing a pumping well that withdraws water and lowers the groundwater table was found to be the most effective flood control measure locally in a small region (e.g., 1km x 1km). By contrast, removing groundwater by building drainage and barriers was also shown to be ineffective to lower the groundwater table over an extended region and was significantly more expensive than the installation of wells. Additionally, when river flooding is taken into account compared to the default scenario where no intake of water from the river is included along the western border of the study area, it is discovered that the spread of pollution is significantly greater.

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

In this paper, based on our previous expertise on ceramic artifacts, several archaeometric methods applied to some samples collected from the Dudești archaeological site (Oltenia region, Romania) are reported for the first time in the literature. The chemical composition and microstructural and morphological characterization of these samples offer important conclusions about the processing conditions. Some specific techniques such as X-ray diffraction (XRD), wave-length-dispersive X-ray fluorescence (WDXRF), Optical microscopy (OM), stereomicroscopy, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy, provide composition information about pigments and their decay processes. Additionally, the Brunauer-Emmett-Teller (BET) method helps to estimate pore sizes and specific surface areas. Thermal analysis (TGA) was used to establish details regarding the production technology and the raw materials source used to make the ceramics, too. The obtained results indicated that the ceramics are based on a paste of muscovite, feldspar, with high plasticity, quartz, melanterite, and calcite, the latter in very low concentrations. According to the obtained results, we could assume that non-calcareous clays are present in the investigated samples because calcium exists in low concentrations. Gypsum is present, too, in very low concentration, identified by the presence of sulfate group in WDXRF. In the same context, iron oxides significantly impact the firing atmosphere of iron-rich clay, resulting in blackening under reducing conditions and reddish coloration under oxidative conditions. Using hematite and gypsum as pigments further contributes to the color variations in the pottery. The consistent firing temperature range of 200-600 °C in Dudești pottery implies a standardized production process, the variation in color being dependent on the specific reducing/oxidative regime conditions. This relationship between clay composition and local sources suggests a connection to Neolithic pottery production in the region and their color depending on the reducing/oxidative regime conditions.

Seeing atomic configuration of single organic nanoparticles at sub-Å spatial resolution by transmission electron microscopy has been so far prevented by the high sensitivity of soft matter to radiation damage. The difficulty is related to the need to irradiate the particle with a total dose of few electrons/Å2, not compatible with the electron beam density necessary to search the low-contrast nanoparticle, to control its drift, to finely adjust the electro-optical conditions and particle orientation, and to finally acquire an effective atomic resolution image. On the other hand, the capability to study individual pristine nanoparticles, such as proteins, active pharmaceutical ingredients, and polymers, with peculiar sensitivity to the variation of the local structure, defects, and strain, would provide advancements in many fields, including materials science, medicine, biology, and pharmacology. Here we report direct sub-ångström resolution imaging at room temperature of pristine unstained crystalline polymer-based nanoparticles. This result is obtained by combining low-dose in-line electron holography and phase-contrast imaging on state-of-the-art equipment, providing an effective tool for the quantitative sub-angstrom imaging of soft matter.

The recent years various, there huge interest to improve the efficiency of smart electronic and optoelectronic devices via developing emerging materials and printing technologies. However, printing technologies becomes one of the most interesting areas for researcher over a convenient coating method because it not only helps to improve the efficiency of device but also help for rapid, reproducible, and low-cost production which open as a new window for mass production for commercial use. Inkjet printing technology has become the most attractive among various printing technologies due to which it is acceptable in most of scientific and various of industrial applications. This review paper presents an overview of the investigations on formulation of the ink, fabrication, and the applications of conductive polymer via inkjet printing for variety of devices including supercapacitors, sensors, electrochromic devices, and patterning of conductive polymers on flexible substrates. The review covers the different conducting polymer explored for supercapacitors, sensors, electrochromic devices, and patterning of conductive polymers, their ink formulation, inkjet printing process and their keys features. This review also presented future perspectives for inkjet printing technology for advanced electronic, optoelectronic, and other conductive polymer-based devices. We believe this review provides new direction to next generation conductive polymer-based devices for various applications.

In this study, we examine microscale waterflooding in a randomly close-packed porous medium. Three different porosities are prepared in a microfluidic platform and saturated with silicone oil. Optical video fluorescence microscopy is used to track the water front as it flows through the porous packed bed. The degree of water saturation is compared to water containing two different types of chemical modifiers, sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP), with water in the absence of a surfactant used as a control. Image analysis of our video data yield saturation curves and calculate fractal dimension, which we use to identify how morphology changes the way an invading water phase moves through the porous media. An inverse analysis based on the implicit pressure explicit saturation (IMPES) simulation technique uses mobility ratio as an adjustable parameter to fit our experimental saturation curves. The results from our inverse analysis combined with our image analysis show that this platform can be used to evaluate the effectiveness of surfactants or polymers as additives for enhancing the transport of water through an oil-saturated porous medium.

The global polyvinyldene flouride market is estimated to reach $937,278.5 thousand by 2019, therefore to develop new membranes and gain pioneering ideas, which could create innovative business opportunities, a fundamental knowledge about membrane properties fabricated from recent commercially available PVDF polymers is highly mandatory. In this study, we successfully prepared nine non-woven supported PVDF membranes using a phase inversion precipitation method starting from a 15 wt% PVDF solution in N-methyl-2-pyrrolidone. Various membrane morphologies were obtained by using (1) PVDF polymers with diverse molecular weight in a range from 300.000 Da to 700.000 Da and (2) different temperatures of the coagulation bath (20, 40, and 60 ±2°C) used for the films precipitation. Environmental Scanning Electron Microscope (ESEM) was used for surface and cross-section morphologies characterization. Atomic Force Microscope (AFM) was employed to investigate surface roughness, while Contact Angle (CA) instrument was used for membranes wettability studies. Fourier Transform Infrared Spectroscopy (FTIR) results show that the fabricated membranes are formed by a mixture of TGTG’ chains in α phase crystalline domains and all-TTTT trans planar zigzag chains characteristic to β phase. Moreover, generated results indicate that the phases content and membrane morphologies depend on the polymer molecular weight and conditions used for the membranes preparation. The diversity of fabricated membranes could be applied by the End User Industries for different applications.

Slimy sculpin (Uranidea cognata) inhabitat coldwater streams in southeastern Minnesota, USA, many of which were subjected to probable 2000-year flood events in August 2007. Floods scoured streambeds, created new stream channels, and greatly reduced benthic invertebrate communities that serve as the primary food resource for sculpin. Diets and Fulton condition of sculpin in Gilmore Creek (with moderate flooding) and Garvin Brook (with very severe flooding) had been examined just prior to flooding, and were re-examined two weeks after flooding to assess possible diet and condition changes. Diets, condition, and reproductive fitness of sculpin were examined seven months post-flood in these same two streams, plus nearby Trout run (also experienced very severe flooding). Sculpin condition declined significantly post-flood in Garvin Brook, but improved in Gilmore Creek. Prior to spring spawning, condition of Garvin Brook sculpin had improved, but Gilmore Creek fish condition worsened. Sculpin diets were more diverse before and after flooding in Gilmore Creek than in Garvin Brook, although diets of fish from both streams were dominated (>55%) by midge (Diptera: Chironomidae) larvae. Diets differed significantly before versus after flooding in the more severely flooded Garvin Brook, but not in Gilmore Creek. Prey number per sculpin stomach declined post-flood in Gilmore Creek, but not in Garvin Brook, although dry mass of prey/fish wet mass declined post-flood in both streams. Pre-spawn sculpin displayed no patterns in reproductive fitness (gonadosomatic index, hepatosomatic index, oocyte number) among the three streams that may have been related to flooding severity the previous summer. Although sculpin diets and condition were altered significantly immediately post-flood in the more severely flooded stream, food resource recovery apparently was rapid enough to prevent longer-term impacts on sculpin condition and reproductive fitness.

Hydrogels have gained significant attention as vehicles for transdermal delivery systems. These polymeric-structured substances have been implemented in pharmaceutical and cosmetic applications. Many factors are employed in their preparation. Light, pH, temperature and specific molecules ligands are commonly used in the production of hydrogels. The Transdermal delivery system (TDD) is a widely used route, used to deliver actives/drugs via the skin. Hydrogels as a TDD have been shown to be efficient in enhancing the efficacy in delivering the actives and drugs. The aim of this review is to discuss the hydrogels application in both dermatological therapeutic and cosmetic applications, covering the types, and properties of hydrogel polymer networks. Furthermore, this review presents one of the most extensively used polymers (Hyaluronic acid HA) in this field and discusses the properties, preparation methods and applications of HA hydrogel patches as a delivery system, including methods of loading the actives and the releasing of these actives from them.

Plastics are very versatile materials that have contributed to the development of society since the 19th century, however, their mismanagement has led to an accumulation of waste in almost every ecosystem affecting the fauna of the planet. In this way recently, studies have shown that some insects might be able to adapt, consuming a wide range of hydrocarbon base polymers. In this work it was studied the adaptive capacity of Zophobas morio larvae when feeding on different synthetic polymers derived from petroleum. Four 30-day larval feeding treatments were carried out with synthetic polymers as expanded polystyrene (PS), low density polyethylene (PBD), polyisoprene (PI) and butyl rubber (BT), in addition a positive control of organic diet was included. Intestinal bacteria were isolated from the treatments and identified by Sanger sequencing. To analyze the chemical composition and physical form of the frass produced, fourier transform infrared spectroscopy (FITR) and images of the feces surface were taken with scanning electron microscopy (SEM) respectively. Zophobas morio larvae were able to consume 54% of PS in 30 days, equivalent to 3.2 mg/d/larva. Nine bacterial strains associated with the decomposition of synthetic polymers were identified in the intestine of the larvae. As for the physicochemical analysis of the feces, FTIR spectra showed the scission of bands corresponding to functional groups of the synthetic polymers in the comparison of the plastic diet treatments versus the feces of antibiotic-treated and plastic-fed larvae, while the comparison of spectra of the plastic and control treatments also identified differences in the absorption peaks. SEM imaging demonstrated that superworm feces differed in dependence on the substrate consumed. The findings demonstrate that Zophobas morio larvae possess a gut biological complex that allows them to feed and survive by consuming various petroleum-derived polymers.