Pseudolysimachion nakaianum (Ohwi) T.Yamaz. is an endemic species that is an important species in the forest ecosystems of South Korea. This study aimed to develop an in vitro propagation system for P. nakaianum, to enhance the availability of this rare and endemic plant for commercial horticulture and restoration efforts. We utilized cotyledon explants from in vitro germinated seeds and two types of explants (petiole and leaf) from in vitro seedlings to assess the impact of five different cytokinins on adventitious shoot organogenesis in P. nakaianum. The half-strength Murashige and Skoog (MS) medium, supplemented with 10 µM thidiazuron (TDZ) for both cotyledon and petiole explants, yielded the highest shoot induction rates (61.1 ± 9.6% and 26.7 ± 8.8%, respectively) and the greatest number of shoots (3 ± 0.6 and 4.4 ± 0.5, respectively). Responses from leaf explants were variable, with none showing in vitro regeneration. Successfully acclimatized P. nakaianum plantlets in a greenhouse demonstrated normal growth. This protocol outlines an effective method for the direct in vitro regeneration from cotyledon and petiole explants of P. nakaianum, providing valuable information for the conservation of this species.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Matrix asphalt material has poor road performance, which is improved by adding polymer modified agents. The original asphalt material experiment research has a certain limitation in that it cannot truly expose the mechanism and influence of modifiers on asphalt materials. To explore the gain effect of the modified agent on the asphalt material's road performance, the molecular dynamic simulation technology is used to explain its mechanism in the micro dimension. The three parameters of the free volume score, radial distribution function and average directional shift diffusion coefficient are analysed to improve the performance of the modifier on asphalt material, an exploration of the microdimension shows that the amount of SBS modifiers is 6% and the amount of rubber modified asphalt material is 22%. The improvement of materials is better than that of rubber modifiers.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

In the article, the authors presented the problem of the transition effect in bridge engineering, its causes, negative consequences, and suggested a solution involving the use of integral bridges with the embankment through a spatial bars structure using reinforced composite polymer material. Integral bridges are designed to collaborate with road or railway embankments in bearing loads. Additionally, their application minimizes maintenance and construction costs while enhancing durability. Current solutions in bridge engineering were described. It is predicted that the presented concept will reduce the amount of plastic waste and contribute to the long-term use of materials. The article emphasized the importance of sustainable development, recycling, and the potential application of substitute materials.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

The present investigation highlights the synthesis of polyaniline (PANI) coated graphene oxide doped with SrTiO3 nanocube nanocomposites through facile in-situ oxidative polymerization method for the efficient removal of carcinogenic dyes, namely, the cationic dye methylene blue (MB) and the anionic dye methyl orange (MO). The synthesised nanocomposites were characterised by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adsorption efficiencies of graphene oxide (GO), PANI homopolymer and SrTiO3 nanocubes-doped nanocomposites were assessed by monitoring the adsorption of methylene blue and methyl orange dyes from aqueous solution. The adsorption efficiency of nanocomposites doped with SrTiO3 nanocubes were found to be of higher magnitude as compared with undoped nanocomposite. Moreover, the nanocomposite with 2 wt% SrTiO3 with respect to graphene oxide demonstrated excellent adsorption behaviour with 99% and 91% removal of MB and MO respectively, in a very short duration of time.

The popularity and growth of additive manufacturing(AM) in recent years are due to its ability to provide innovative solutions to complex manufacturing challenges and its potential to transform the way products are designed, developed, and produced. In this work, the numerical simulation geometry of the model extruder from nozzle is established along with the material extrusion process. The high gravity material extrusion system (HG-MEX) properties and characteristics during filament fabrication are evaluated. This work investigates the effects of gravity on the material extrusion process from nozzle extrusion. This work is unique in the incorporation of fluid surface characteristics to represent the performance and contact with the material extrusion in additive manufacturing. The use of simulation in high gravity material extrusion in additive manufacturing is a meaningful and valuable approach to improving the quality and efficiency of the process.

Polymers are one of the most widely used chemicals in the oil and gas industry. They are used for mobility control in enhanced oil recovery, in conformance control as a crosslinked plugging agent, as a fracking fluid for fracture propagation and proppant transportation, and in drilling fluids as an additive for drilling mud enhancement. In the majority of its applications in the petroleum industry, the polymer needs to be injected under high pressures and temperatures. This can impact the polymer structure significantly and compromises the possibility of reusing the injected polymer for cost reduction and material sustainability. This research characterizes the polymer injectivity in different pore sizes under different conditions and evaluates the polymer conditions after injection. Based on this, the ability to reinject the polymer in the porous media is discussed. The factors studied include the pore size, the polymer concentration, the polymer injection flowrate, and polymer injectivity. Results showed that the polymer usually undergoes four main degradations during injection including dehydration, syneresis, shearing, and excessive hydrolysis. The experimental results showed that one or more of the polymer degradations resulted in the inability to reinject the polymer in most cases.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

The study of the tribological behavior of the braking system in auto vehicles requires knowing the characteristics of the material in contact and, in the work process, for the friction pair, brake disc-pads. Materials structural analysis is necessary because the wear process depends on the friction pair chemical composition, and brake disk-pads, respectively on the work process parameters (pressing force, rotational speed, traffic conditions, etc.). The material of the brake discs is generally the same gray cast iron, but the brake pads can be semi-metallic (particles of steel, copper, brass, and graphite, all united with a special resin), organic materials (particles of rubber, glass, and kevlar all joined with the help of a resin), composite materials that contain different constituents and ceramic materials (rarely have small copper particles). Therefore, the purpose of the paper is to know the crystalline structure and the mechanical properties of the brake pad materials, through specific studies and analyses, with important implications on the friction and wear behavior.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

The susceptible-infected-recovered-vaccinated-deceased (SIRVD) epidemic compartment model extends the SIR model to include the effects of vaccination campaigns and time-dependent fatality rates on epidemic outbreaks. It encompasses the SIR, SIRV, SIRD, and SI models as special cases, with individual time-dependent rates governing transitions between different fractions. We investigate a special class of exact solutions and accurate analytical approximations for the SIRVD and SIRD compartment models. While the SIRVD and SIRD equations pose complex integro-differential equations for the rate of new infections and the fractions as a function of time, a simpler approach considers determining equations for the sum of ratios for given variations. This approach enables us to derive fully exact analytical solutions for the SIRVD and SIRD models. For nonlinear models with a high-dimensional parameter space, such as the SIRVD and SIRD models, analytical solutions, exact or accurately approximative, are of high importance and interest: not only as suitable benchmarks for numerical codes, but especially as they allow us to understand the critical behavior of epidemic outbursts as well as the decisive role of certain parameters. In the second part of our study, we apply a recently developed analytical approximation for the SIR and SIRV models to the more general SIRVD model. This approximation offers accurate analytical expressions for epidemic quantities, such as the rate of new infections and the fraction of infected persons, particularly when the cumulative fraction of infections is small. The distinction between recovered and deceased individuals in the SIRVD model affects the calculation of the death rate, which is proportional to the infected fraction in the SIRVD/SIRD cases but often proportional to the rate of new infections in many SIR models using a posteriori approach. We demonstrate that the temporal dependence of the infected fraction and the rate of new infections differs when considering the effects of vaccinations and when the real-time dependence of fatality and recovery rates diverge. These differences are highlighted for stationary ratios and gradually decreasing fatality rates. \Revised{The case of stationary ratios allows one to construct a new powerful diagnostics method to extract analytically all SIRVD model parameters from measured COVID-19 data of a completed pandemic wave.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Kamchatka berries (Lonicera caerulea L.) are known for their high content of phenolic compounds or vitamins, which is reflected in their antibacterial, detoxifying and anti-inflammatory properties. They are used in the production of jams, juices, wines and as natural dye. A bioferment was prepared from the pomace of the Kamchatka berry varieties Aurora and Indigo Gem and the strains Saccharomyces cerevisiae and Lacticaseibacillus paracasei, which was used to prepare a cosmetic preparation with a concentration of 5% in accordance with the guidelines of the COSMOS certification body. Conducted physico-chemical and organoleptic analyses and bioactive profile characterisation (UHPLC-DAD and UHPLC-ESI-MS/MS). The results showed that the presence of caffeic acid 4.47 ± 0.07 mg/100g was detected after fermentation of Kamchatka berry pomace. Vitamin C content increased by 141% after fermentation of Kamchatka berry pomace. The results of stability tests showed that in the process of physicochemical analysis of cosmetic preparation with bioferment of Kamchatka berry pomace the pH should oscillate in the range of 4.38-4.76 ± 0.01. Stability tests showed that the cosmetic should be protected from high temperatures and UV radiation and proved that the product is stable under changing conditions, resulting in lower transport and storage costs.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

Microplastics (MPs) are a critical environmental issue, with impacts ranging from ecosystem contamination to health risks through bioaccumulation. This review addresses the inefficacy of traditional water treatments in removing MPs and proposes photodegradation, particularly via nanomaterial-enhanced photocatalysts, as a solution. Utilizing their unique properties like large surface area and tunable bandgap, nanomaterials significantly improve degradation efficiency. Different strategies for photocatalysts modification to improve photocatalytic performance are thoroughly summarized, with the particular emphasis on element doping and heterojunction construction. Furthermore, this review thoroughly summarizes the possible fundamental mechanisms driving photodegradation of microplastics facilitated by nanomaterials, with a focus on processes like free radical formation and singlet oxygen oxidation. By clearly elucidating these strategies and mechanisms, this review aims to provide valuable insights and inspire further progress in microplastic photodegradation.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Novel bio-inspired materials have gained recently great attention, especially in medical applications. Applying sophisticated design and engineering methods, various polymer-polymer hybrid systems with outstanding performance have been developed in last decades. Hybrid systems composed of bioelastomers and hydrogels are very attractive due to their high biocompatibility and elastic nature for advanced biomaterials used in various medical applications such as drug delivery systems and scaffolds for tissue engineering. Herein, we describe the advances in current state-of-the-art design, properties and applications of polymer-polymer hybrid systems in medical applications. Bio-inspired functionalities, including bioadhesiveness, injectability, antibacterial properties and degradability applicable to advanced drug delivery systems and medical devices will be discussed in a context of future efforts towards development of bioinspired materials.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Hydrogels prepared from natural polymer have attracted extensive attentions in biomedical fields such as drug delivery, wound healing, and regenerative medicine due to their good biocompatibility, degradability and flexibility. This review outlines the commonly used natural polymer in hydrogel preparation, including cellulose, chitosan, collagen/gelatin, alginate, hyaluronic acid and starch. The polymeric structure and process/synthesis of natural polymers are illustrated, and natural polymer-based hydrogels including the hydrogel formation and properties are elaborated. Subsequently, the biomedical application of hydrogels based on natural polymer in drug delivery, tissue regeneration, wound healing and other biomedical field is summarized. Finally, the future perspectives of natural polymers and hydrogels based on them are discussed. For natural polymer, novel technologies such as enzymatic and biological methods are developed to improve the structural properties and the development of new natural based polymers or natural polymer derivatives with high performance is still very important and challenging. For natural polymer-based hydrogels, novel hydrogel materials, like double-network hydrogel, multifunctional composite hydrogels and hydrogel microrobots are designed to meet the advanced requirements in biomedical application, and new strategies such as dual-crosslinking, microfluidic chip, micropatterning and 3D/4D bioprinting, have been explored to fabricate advanced hydrogel materials with designed properties for biomedical application. Overall, natural polymeric hydrogels have attracted increasing interests in biomedical application, and the development of novel natural polymer-based materials and new strategies/methods for hydrogel fabrication is badly desirable and still challenging.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p<0.05; p<0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p<0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

Due to the growing interest in biopolymers, biosynthesizable and biodegradable polymers currently occupy a special place. Unfortunately, the properties of native biopolymers are not satisfactory, which explain that attempts are being made to modify them. The work attempts to improve the properties of poly(3-hydroxybutyrate) (P3HB) using linear aliphatic polyurethane (PU) based on 1,4-butanediol and hexamethylene 1,6-diisocyanate. The conducted studies on the effect of the amount of PU used (5, 10, 15 and 20 wt.%) showed an improvement in the thermal properties of the prepared polymer blends. There was an increase in the degradation temperature of the ob-tained blends in relation to the native P3HB by 12-57C, and the difference between the melting point and the degradation point was above 100°C for most of the obtained blends. As part of the tested mechanical properties of the new polymer blends, we noted the desired increase in the tensile strength, in the relative elongation at break and in the impact strength with a decrease in hardness, in particular with the presence of 5 wt.% PU. Therefore, for further improvement, hybrid nanobiocomposites with 5 wt.% PU and organically modified montmorillonite (MMT – Cloisite 30B) were produced. The nanoadditive was used in typical amount of 1-3 wt.%. The nanostructure of the biocomposites produced by extrusion was examined by small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM), the morphology by scanning electron microscopy (SEM), and compatibility by infrared spectroscopy (FT IR). In addition, selected mechanical properties were determined and thermal properties were tested by the thermogravimetric analysis (TGA) and the standard differential scanning calorimetry (DSC). The polyester and polyurethane chains penetrated into the interlayer spaces of organically modi-fied nanoclay – Cloisite30B and the complete delamination occurred during direct mixing in the extrusion process. FT IR spectral analysis showed the compatibility of the polymer biocomposite components by the coexistence of intermolecular interactions in the form of hydrogen bonds. The morphology studies of the produced hybrid nanobiocomposites showed an interaction of the bi-opolymer matrix with PU and Cloisite30B and the formation of easily migrating polyester-polyurethane-montmorillonite adducts, which resulted in improved mechanical properties com-pared to the properties of the native P3HB and P3HB-PU compositions. The influence of the presence of a nanofiller on the properties of the prepared nanobiocomposites was tested and it was found that, as expected, the smallest amount of nanofiller provides the best results.It was found that the obtained nanobiocomposites containing the smallest amount of nano-fillers, i.e. 1 wt.% Cloisite30B exhibited the best mechanical and thermal properties. The desired decrease in hardness by 15% and a higher value of impact strength by 15%, an increase in elonga-tion at break by 60% and an increase in thermal stability of the newly produced biocomposites compared to to the native P3HB were observed. The prepared nanobiocomposites combined the best features caused by the elasticizing effect of polyurethane and the formation of P3HB-PU-MMT adducts.

Successful fertilization treatments targeted to improve stand productivity while reducing operational complexities and cost depend on a clear understanding of soil nutrient availability under varying environmental conditions. Soil nutrient data collected from 154 forest sites throughout the Inland Northwest, USA were analyzed to examine soil nutrient characteristics on different geologic soil parent materials and to rank soil fertility. Results show that soil parent material explains significant differences in soil nutrient availability. Soils developed from volcanic rocks have the highest CEC and are relatively high in P, K, S, Mg, Cu, Ca, and B, but generally poor in N. Forest soils developed from plutonic rocks exhibit the lowest CEC and are low in N, S, K, Mg, Cu, and Ca, but higher in P. Some soils located on mixed glacial till are low only in K, Cu, Mg, and Ca, but many glacial soils are relatively rich in other nutrients, albeit the second lowest CEC. Soils developed from metasedimentary and sedimentary rocks are among those with lowest soil nutrient availability for P and B. Sulfur was found to have the highest concentrations in metasedimentary influenced soils and the least in sedimentary derived soils. Our results should be useful in designing site-specific fertilizer and nutrient management prescriptions for forest stands growing on soils developed from these major geologies within the Inland Northwest region of the United States.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

A series of waterborne polyurethane (WBPU)/modified lignin amine (MLA) adhesives was prepared using modified lignin amine (MLA) as a chain extender by a prepolymer mixing process. A successful Mannich reaction was achieved during the synthesis of MLA by reacting lignin with bis(3-aminopropyl)amine. Higher tensile strength, Young’s modulus and thermal stability were recorded for WBPU/MLA adhesives with higher MLA contents. The WBPU/MLA adhesive materials were used to coat PVC substrates. The adhesive strength increased with increasing MLA content. More importantly, the MLA also enhanced the WBPU/MLA coating in terms of adhesive strength at moderately high temperatures as well as under natural weather exposed conditions. The adhesive strength was essentially unaffected with 6.48 mole% MLA in the WBPU/MLA coating after exposure to natural weather conditions for 180 days.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

The escalating demand for multifunctional and advanced materials for growing industries has turned scientific exploration to graphene-based hybrid filler polymer composites. The introduction of graphene with other fillers into polymer matrices results in astonishing properties and thus has gained significant attention in recent years. This study addresses the significance of graphene-based hybrid filler polymer composites in progressive materials science and engineering. The paper encloses some traditional and current preparation techniques employed in the fabrication of composites and a comprehensive review of successfully prepared graphene hybrid polymer composites with enhanced mechanical, thermal, and electrical properties reported in published research. The role of different factors, e.g., filler type, aspect ratios, filler-matrix compatibility, dispersion effects, homogeneity, filler orientation through polymer matrices, and curing conditions, are summarized. Finally, the applications in heavy industries, e.g., aerospace, electronics, energy storage, and automotive sectors were also analyzed. We hope this study will serve as a practical resource for new researchers and practitioners to understand and harness the full potential of these composites in various scientific and industrial fields.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

Because this issue journal is dedicated to Gelatin here we present a few applications of gelatin in the field of optics. It is understood that optics is the science that studies the production, propagation, interaction and detection of light. Regarding the detection there are some materials sensitive to light (photosensitive) that are used like photomultipliers, CCD’s, crystals, two dimension (2D) materials and more. Among the 2D materials the most popular through several centuries has been gelatin based photographic emulsion that records spatial distributions of light. More recently (1970) films made of Gelatin with Dichromate (DCG) and dyes have been used. We describe some characteristics and applications of these two photosensitive materials. Also we describe examples where gelatin is used as Relative Humidity (RH) sensor and in the fabrication of optical elements based on gelatin. This article is intended to researchers outside the optics community.

Polymer hydrogels are 3D networks consisting of hydrophilic crosslinked macromolecular chains, able to swell and retain water. Since their invention in the 1960s, they have become an outstanding pillar in the design, development, and application of engineered polymer systems suitable for biomedical and pharmaceutical applications (such as drug or cell delivery, regeneration of hard and soft tissues, wound healing, and bleeding prevention, among others). Despite several well-established synthetic routes of polymer hydrogels based on batch polymerization techniques, about fifteen years ago academia started to look for alternative methods involving simpler reaction paths, shorter reaction times, and lower energy consumption. In this context, frontal polymerization (FP) undoubtedly has become an alternative and efficient reaction model that allows for converting monomers into polymers via a localized and propagating reaction, by exploiting the formation and propagation of a “hot” polymerization front, able to self-sustain and propagate throughout the monomeric mixture. Therefore, the present work aims to summarize the main research outcomes, achieved during the last years, concerning the design, preparation, and application of FP-derived polymeric hydrogels, demonstrating the feasibility of this technique for the obtainment of functional 3D networks, and providing the reader with some perspectives for the forthcoming years.

Polymer flooding is one of the most successful chemical EOR methods, and is primarily implemented to accelerate oil production by sweep improvement. However, other benefits have extended the utility of polymers. During the last decade, it has been evaluated for an increasing number of fields, both offshore and onshore. This is a consequence of improved polymer properties, which extends the use to HTHS (high temperature high salinity) conditions and of improved understanding of flow mechanisms such as for heavy oil mobilization. A key issue in understanding polymer performance is to control and predict in-situ porous medium rheology. The first part of this paper reviews recent developments in understanding polymer flow in porous medium. Especially, polymer in-situ rheology and injectivity is discussed. The second part of this paper reports polymer flow experiments using the most applied polymer for EOR processes, HPAM (partially hydrolyzed polyacrylamide). The experiments address high rate near-wellbore behavior (radial flow) as well as reservoir rate steady state flow (linear flow) and discuss differences observed in terms of flow conditions. In addition, impact of oil on polymer rheology was investigated, and compared to single-phase polymer flow in Bentheimer sandstone rock material. Presence of oil leads to a reduction in apparent viscosity.

The need to develop novel lightweight materials and their manufacturing processes is sets out to meet the new aerospace, automotive and construction requirements. Within this context, this research work is proposed to develop a novel thermoplastic composite material with high mechanical properties. These composites will be based on thermoplastic matrixes made from polyamide and 35% short glass fiber filled-polyamide reinforced with different types of fabrics. As reinforcement, glass fiber fabrics will be used as the base. They will be treated with different processes, both chemical and physical, to promote adherence to the matrix. Textile overmoulding technology was selected for manufacturing these composites. This technology was primarily developed to manufacture aesthetic lined components and has achieved a great implantation. Once these new composites are manufactured, they will be submitted to different tests to evaluate their behavior regarding adhesion, impact strength and stiffness. It is expected an improvement on stiffness and impact absorption.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

It is often difficult to extract data on material and energy wates and related costs in the value chain of conventional production units. Many organizations are not fully aware of the actual cost of material and energy waste. For this purpose, advanced costing methods should be used. This study uses material and energy flow cost accounting to determine material costs, losses, and waste management. The case study of this research is the construction of turbine blades in Iran Power Plant Company. In this study, using the extracted data, the construction costs of turbine blades have been studied. The conventional method of making a turbine blade is the machining method, which we will see has a huge amount of wastes of materials and energy. By studying different methods, we will find that there is an alternative method called forging, which reduces losses and costs. Finally, the costs of the two methods are compared. Engineering economics techniques have also been used to compare two methods on a long-term planning horizon.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

When different strain hardening and strain rate sensitive materials are used for scaled model and prototype, the traditional pure geometrical similarity laws of solid mechanics will fail. Although correcting the basic scaling factors of velocity, density and geometry have been developed to compensate for the material distortion in recent non-geometric scaling works, it is difficult to be widely used because of its inherent indirect (depending on the structural strain and strain rate responses) and inexact (having significant prediction errors for prototype) defects. In this paper, a framework of material similarity, based on the new suggested material dimensionless numbers and the ‘Material number vs. strain/strain-rate’ function curves, are further developed, which represents the objective requirement of similarity theory for the basic mechanical properties of materials. It is demonstrated what is similitude materials of solid mechanics and how to use the best similitude materials to overcome the non-scalabilities of materials for identical or different materials. The direct and exact solution of the basic correction factors is further obtained and therefore overcomes the previous inherent indirect and inexact defects radically. Based on the similarity evaluation of different materials of the classical constitutive models, the impacted structures of circular plate and crooked plate with strain hardening and strain rate sensitive materials are verified numerically. The results show the completely different materials can be exact similitude for various structural behaviors (strain, strain rate, stress and displacement) of time and space fields after using the best similitude materials; and the basic correction factors do not depend on the structural strain and strain rate responses. As a contrast, when the non-similitude materials are used, the similarity results are very sensitive to the selection of strain/strain-rate and often leads to failed predictions. In addition, for the material elastic and temperature effects, the proposed method is also discussed to be valid.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

Dermal wound healing describes the progressive repair and recalcitrant mechanism of damaged skin and eventually reformatting and reshaping the skin. Many probiotics, nutraceuticals, metal nanoparticles have been associated with improved healing process of intra and inter tissue wounds. Despite the vast nature on material based wound healing mediators, the exact mechanism on material-cellular interaction is still point of repent issue particularly in diabetics and pathological condition. The use of bioengineered alternative agents will likely only continue to dominate the outpatient and perioperative management of chronic, recalcitrant wounds as new additional products continue to cut costs and improve wound healing process. This review article provides an update of the various remedies with confirmed wound healing activities by a diverse group of agents from previous experiments conducted by various researchers

Polyvinyl alcohol (PVA) is highly compatible polymer with biological environments. Specifically, it has been used as a trap for different types of microorganisms in Bio-MEMS, and its properties can be modified to act as an electrode for electrochemical analysis. This study presents a nano-composite developed with PVA, multiwall carbon nanotubes (CNTs) doped with nitrogen, which changes the electrical properties of the polymer and its viscosity to obtain nanofibers by electro-spinning. The proposed nanocomposite was characterized using Fourier transform-infrared and Raman spectroscopy techniques, confirming the presence of the CNTs immersed in the polymer. High-resolution transmission electron microscopy was used to obtain the micrographs that showed the characteristic interplanar distances of the multiwall CNT in the polymeric matrix with values of 3.63 Å. Finally, the CNx mats were exposed to various aqueous solutions in a po-tentiostat to demonstrate the effectiveness of the nanofibers for electrochemical analysis. The CNx-induced changes in the electrical properties of the polymer were identified using cyclic voltammograms, while the electrochemical analysis revealed supercapacitor behavior.

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15%wt) and the sliding regime parameters (load: 1 N, 2.5 N and 5 N, the sliding speed: 0.25 m/s, 0.5 m/s and 0.75 m/s, and the sliding distance: 2500 m, 5000 m and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix.

The practice of teaching and scientific research on cadaveric material remains crucial for medical education, especially in surgical disciplines. However, in Italy, this practice has been neglected due to legislative insufficiency and financial constraints. Although innovative methods and tools like simulators and e-learning have been adopted, direct hands-on experience with human cadavers remains irreplaceable for medical and surgical education. The absence of clear legislation governing cadaveric dissection has limited availability for teaching and research, resulting in economic burdens for universities and individuals seeking proper surgical training. To address this issue, the Law No. 10/2020 and the recent implementing decree were introduced in Italy, providing detailed legislation on the donation of bodies for educational and research purposes. The law emphasizes the importance of respecting the donor's specific choices and aligns with constitutional principles promoting culture, research, and health protection. However, some critical issues related to consent procedures, duration of body availability, and preservation of anatomical parts remain. Additionally, the law's dissemination among the population needs improvement. Future optimization could include allowing donors to choose the timing of body donation and considering different timeframes for body availability. Furthermore, the implementation of consent procedures could be simplified to increase donations. The law should also address the need for appropriate reception centers and allocate resources for effective dissemination. Despite these challenges, Law No. 10/2020 represents a significant step forward in enhancing medical-surgical training, scientific research, and the overall quality of patient care in Italy.

This paper is focused on understanding multiscale modelling to obtain a bridge among different time and length scales of simulation techniques. These techniques are vital as it holds the potential to understand and predict the capabilities of polymer nanocomposites (PNCs). However, an appropriate approach in controlling the interfacial interaction between nanoparticle and polymer in nanocomposites structure is still needed to develop. In this review, an initial brief introduction to various trending simulation techniques has been discussed at all three levels of scale (nm, μm, mm). Later, descriptive study on fundamental issues such as thermodynamics, kinetics, mechanical properties, and morphology has been studied deeply. The multiscale modeling bridges the gaps of simulation between the different scales of models from molecular to mesoscale levels working over the broad range of length and timescale. Through the sequential, adaptive, and concurrent approaches, we can develop a system that may comprehend multiscale mode modeling adaptive resolution approach has recently added approach the molecule of the subject can shift their position freely in the domain and through this approach and studied the Brownian motion. Co-The co-current coach is also termed as handshaking path and it is linked aiming at different scale models. Covering the rigid techniques smoothly and linking them at different scales helps in normalizing the statistical behaviour.

One of the most popular techniques for determining electrical properties of material is the free-space measurement technique. With the potential for new applications requiring efficient, accurate and broadband material measurement systems using higher millimeter-wave and terahertz frequencies, the free-space measurement method has received renewed interest. This is mainly due to its simplicity, favorable properties as a non-destructive method, and it allows transmission and reflection measurements without any physical contact with the sample. This paper reviews and discusses state- of-the-art free space material measurement systems, starting with the different measurement techniques available for material characterization, their important concepts, post-processing in determining their properties, and progress towards expanding their use at higher frequencies. Also, this paper reviews dielectric material characterization using the free space method focusing on their application extension towards the higher frequencies. Besides, the algorithms for conversion methods and usage of lens in free space material measurement system was discussed in this paper. Finally, a future perspective on the outlook of this free space method is presented prior to the conclusion.

The aim of this research was to undertake laboratory testing to investigate the beneficial effects of epoxy resin grouts on the physical and mechanical properties of sands with a wide range of granulometric characteristics. Six sands, of different particle size and uniformity coefficients, were grouted using epoxy resin solutions with three ratios of epoxy resin to water (3.0, 2.0 and 1.5). A set of unconfined compressive strength tests were conducted on grouted samples at different curing periods and a set of long-term unconfined compressive creep tests in dry and wet conditions after 180 days of curing were also carried out, in order to evaluate the development of the mechanical properties of the sands, as well as, the impact of water on them. The findings of the investigation showed that epoxy resin resulted in appreciable strength values in the specimens, especially those of fine sands, grouted with the different epoxy resin grouts. In general, the compressive strength varied between 0.68 - 5.60 MPa and the modulus of elasticity between 75 - 480 MPa, after a curing period of 180 days. In terms of physical properties, the permeability and porosity (before and after the grouting process) were estimated. Grouts with an epoxy resin to water ratio of 3 decreased permeability by up to four orders of magnitude. Using laboratory results and regression analysis, three mathematical equations were developed that relate each of the dependent variables; compressive strength, elastic modulus, and coefficient of permeability, with particular explanatory variables.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

Chitosan arouses large interest due to its properties and possible applications. Every year the number of publications and patents based on this polymer increases. Chitosan exhibits poor solubility in neutral and basic media limiting its use in such conditions. Another serious obstacle is directly related to its natural origin. Chitosan is not a single polymer with a defined structure but a family of molecules with differences in their composition, size, and monomer distribution. These properties have a fundamental effect on the biological and technological performance of the polymer. Moreover, some of the biological properties claimed are discrete. In this review, we discuss how chitosan chemistry can solve the problems related to its poor solubility and can boost the polymer properties. We focus on some of the main biological properties of chitosan and the relationship with the physicochemical properties of the polymer. Then, we visit two polymer applications related to green processes: the use of chitosan in the green synthesis of metallic na-noparticles and its use as support in biocatalyst. Finally, we briefly describe how making use of the technological properties of chitosan it is possible to develop a variety of systems for drug delivery

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

The recent years various, there huge interest to improve the efficiency of smart electronic and optoelectronic devices via developing emerging materials and printing technologies. However, printing technologies becomes one of the most interesting areas for researcher over a convenient coating method because it not only helps to improve the efficiency of device but also help for rapid, reproducible, and low-cost production which open as a new window for mass production for commercial use. Inkjet printing technology has become the most attractive among various printing technologies due to which it is acceptable in most of scientific and various of industrial applications. This review paper presents an overview of the investigations on formulation of the ink, fabrication, and the applications of conductive polymer via inkjet printing for variety of devices including supercapacitors, sensors, electrochromic devices, and patterning of conductive polymers on flexible substrates. The review covers the different conducting polymer explored for supercapacitors, sensors, electrochromic devices, and patterning of conductive polymers, their ink formulation, inkjet printing process and their keys features. This review also presented future perspectives for inkjet printing technology for advanced electronic, optoelectronic, and other conductive polymer-based devices. We believe this review provides new direction to next generation conductive polymer-based devices for various applications.

In this study, we examine microscale waterflooding in a randomly close-packed porous medium. Three different porosities are prepared in a microfluidic platform and saturated with silicone oil. Optical video fluorescence microscopy is used to track the water front as it flows through the porous packed bed. The degree of water saturation is compared to water containing two different types of chemical modifiers, sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP), with water in the absence of a surfactant used as a control. Image analysis of our video data yield saturation curves and calculate fractal dimension, which we use to identify how morphology changes the way an invading water phase moves through the porous media. An inverse analysis based on the implicit pressure explicit saturation (IMPES) simulation technique uses mobility ratio as an adjustable parameter to fit our experimental saturation curves. The results from our inverse analysis combined with our image analysis show that this platform can be used to evaluate the effectiveness of surfactants or polymers as additives for enhancing the transport of water through an oil-saturated porous medium.

The global polyvinyldene flouride market is estimated to reach $937,278.5 thousand by 2019, therefore to develop new membranes and gain pioneering ideas, which could create innovative business opportunities, a fundamental knowledge about membrane properties fabricated from recent commercially available PVDF polymers is highly mandatory. In this study, we successfully prepared nine non-woven supported PVDF membranes using a phase inversion precipitation method starting from a 15 wt% PVDF solution in N-methyl-2-pyrrolidone. Various membrane morphologies were obtained by using (1) PVDF polymers with diverse molecular weight in a range from 300.000 Da to 700.000 Da and (2) different temperatures of the coagulation bath (20, 40, and 60 ±2°C) used for the films precipitation. Environmental Scanning Electron Microscope (ESEM) was used for surface and cross-section morphologies characterization. Atomic Force Microscope (AFM) was employed to investigate surface roughness, while Contact Angle (CA) instrument was used for membranes wettability studies. Fourier Transform Infrared Spectroscopy (FTIR) results show that the fabricated membranes are formed by a mixture of TGTG’ chains in α phase crystalline domains and all-TTTT trans planar zigzag chains characteristic to β phase. Moreover, generated results indicate that the phases content and membrane morphologies depend on the polymer molecular weight and conditions used for the membranes preparation. The diversity of fabricated membranes could be applied by the End User Industries for different applications.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

We confidently approach current issues in Green Finance (GF) from the perspective of an international organization, where the first author has previous experience as a support assistant. In fact, the economy of the EU (European Union) is deeply involved in the changing needs related to the dramatic consequences of climate change and environmental degradation, which has placed the needs of a more sustainable economy at the top of the international agenda. The environmental, social and governance (ESG) aspects are marginally addressed to arouse a major interest in questions raised by green financial products which require long-term profit expectations, and which above all contain a margin of risk that is difficult to calculate in the landscape of traditional financial instruments. Through a careful approach akin to artificial intelligence research methods, we attempt to “materialize” at least the most visible clues of this fashionable economic shift through what we call SMC (sustainable material culture) objects. The presented SMC objects serve as tangible representations of sustainable practices and can promote awareness and action incorporating into everyday life and business practices a powerful reminder and catalyst for a shift towards more sustainable investment and consumption patterns.

The field of power harvesting has experienced significant growth over the past few years due to the ever-increasing desire to produce portable and wireless electronics with extended lifespans. The present work aims to introduce an approach to harvesting electrical energy from a mechanically excited piezoelectric element and investigates a power analytical model generated by a smart structure of type polyvinylidene fluoride(PVDF) that can be stuck onto fabrics and flexible substrates, although we report the effects of various substrates and investigates the sticking of these substrates on the characterization of the piezoelectric material.

The Maxwell equations of electrodynamics describe electrical and magnetic forces with great accuracy in the vacuum of space. But the equations of electrodynamics applied to material systems are usually written in a way that obscures their accuracy. The usual formulation of the Maxwell equations includes a dielectric constant as a single real number that grossly over-approximates the actual properties of matter, particularly liquid matter so important in applications of electrodynamics to biology and chemistry. We rewrite two Maxwell equations here to make clear the precision of the Maxwell equations in the presence or absence of matter. We discuss and derive two well known corollaries that are as universal and precise as the Maxwell equations themselves: (1) a continuity equation that relates charge and flux and (2) a conservation equation in which total current never accumulates at all. The total current is the right hand side of the Ampere-Maxwell law. Total current is perfectly incompressible. It is conserved exactly, everywhere and at every time, independent of the microphysics of charge conduction. The total current combines the flux of charges and the ethereal current. The ethereal current \varepsilon_{o\ }\sfrac{\partial\mathbf{E}}{\partial t}\ exists everywhere, including the interior of atoms, because it is a property of space, not matter. The ethereal current exists, and thus flows, in a vacuum devoid of mass. The ethereal current is a consequence of the relativistic (Lorentz) invariance of charge. Charge does not change even if it moves at speeds approaching the velocity of light. Total current has properties quite distinct from flux of mass because of the ethereal current. Most strikingly, in the one dimensional unbranched systems of electronic circuits and biological ion channels, the total current is independent of location, even if the flux of charges varies a great deal. Indeed, the Maxwell equations—and thus conservation of total current—act as a perfect low pass spatial filter, converting the infinite variation of (the Brownian model of) thermal motion of charges to the zero variation of the total current.

Dampers provide safety by control of unwanted motion, due to conversion of mechanical work into another form of energy (e.g., heat). State of the art materials are elastomers including thermoplastic-elastomers. For polymer-appropriate replacement of multi-component shock absorbers comprising mounts, rods, hydraulic fluids, pneumatic devices, or electro-magnetic devices, among others, deep insights of the dynamic thermo-mechanical characteristics of damper materials have to be gained. The ultimate objective is to reduce complexity by utilizing inherent material damping rather than structural (multi-component) damping properties. The objective of this work was to compare the damping behavior of different elastomeric materials including thermoplastic poly(urethane) (TPU), and silicone rubber blends (mixtures of different poly(dimethylsiloxane) (PDMS)). Therefore, the materials were hyper- and viscoelastic characterized, a finite element calculation of a ball-drop test was performed, and for validation the rebound resilience was measured experimentally. In an attempt, the coil-over shock absorber of a model car was replaced by a damper made of the examined and modeled materials. The results revealed that the material parameter determination methodology is reliable, and the data applied for simulation lead to realistic predictions. Interestingly, the rebound resilience of the mixture of soft and hard PDMS (50:50)w% is the highest and the lowest values were measured for TPU.

Additive manufacturing has already been established as a highly versatile manufacturing technique with demonstrated potential to completely transform conventional manufacturing in the future. The objective of this paper is to review the latest progress and challenges associated with the fabrication of multi-material parts using additive manufacturing technologies. Various manufacturing processes and materials used to produce functional components were investigated and summarized. The latest applications of multi-material additive manufacturing (MMAM) in automotive, aerospace, biomedical and dentistry field were demonstrated. Investigation on the current challenges were also carried out to predict the future direction of MMAM processes. It is concluded that the further research and development needed in the design of multi-material interfaces, manufacturing processes and material compatibility of MMAM parts are necessary.

3D-printing with foam concrete, which is known for its distinct physical and mechanical properties, has not yet been purposefully investigated. The article at hand presents a methodological approach for the mixture design of 3D-printable foam concretes and a systematic investigation of the potential application of this type of material in digital construction. Three different foam concrete compositions with water-to-binder ratios between 0.33 and 0.36 and having densities of 1100 to 1580 kg/m³ in the fresh state were produced with a pre-foaming technique using a protein-based foaming agent. Based on the fresh-state tests, including 3D-printing as such, an optimum composition was identified and its compressive and flexural strengths were characterised. The printable foam concrete showed compressive strength above 10 MPa and low thermal conductivity, which make it suitable for 3D-printing applications, while fulfilling both load-carrying and insulating functions.

Metal nanoparticles are used to modify/enhance the properties of a polymer matrix for a broad range of applications in bio-nanotechnology. Here, we study the properties of polymer/gold nanoparticle (NP) nanocomposites through atomistic molecular dynamics, MD, simulations. We probe the structural, conformational and dynamical properties of polymer chains at the vicinity of a gold (Au) NP and a functionalized (core/shell) Au NP, and compare them against the behavior of bulk PE. The bare Au NPs were constructed via a systematic methodology starting from ab-initio calculations and an atomistic Wulff construction algorithm resulting in the crystal shape with the minimum surface energy. For the functionalized NPs the interactions between gold atoms and chemically adsorbed functional groups change their shape. As a model polymer matrix we consider polyethylene of different molecular lengths, from the oligomer to unentangled Rouse like systems. By computing the different properties the concept of the interface, and the interphase as well, in polymer nanocomposites with metal NPs are critically examined. Results concerning polymer density profiles, bond order parameter, segmental and terminal dynamics show clearly that the size of the interface / interphase, depends on the actual property under study. In addition, the anchored polymeric chains change the behavior/properties, and especially the chain density profile and the dynamics, of the polymer chain at the vicinity of the Au NP.

Long-acting (LA) drug-delivery system (DDS) successes are linked to their abilities to harness biocompatible polymers and materials for sustained and predictable release of therapeutic agents over an extended period of time. For human immune deficiency virus type one (HIV-1) infections, LA DDSs hold great promise in closing the gaps of daily oral therapy for treatment and prevention. Examples are Cabenuva, Apretude and Sunlenca, which have been shown to be safe and effective. Alternative promising drug delivery technologies such as implants, prodrugs, vaginal rings, and microarray patches are being explored to further meet patients’ needs. We posit that improved physicochemical properties of the formulation payloads and material chemistry design with optimal drug release kinetics holds the potential to optimize release profiles. Furthermore, for the treatment and prevention of HIV-1 infection, the landscape of LA medicines now in clinical or preclinical development offers hope that the strategic design of polymers will further improve upon controlled delivery of drugs to simplify dosing schedules.

Temperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in hazardous working environments (air pollution, chemical or ionizing contamination), and the presence of electromagnetic disturbances. The use of fiber optic temperature sensors in polymer technology can significantly reduce the cost of their production. Moreover, the installation process and usage would be simplified. As a result, these types of sensors would becoming increasingly popular in industrial solutions. This review provides a critical overview of the latest development of fiber optic temperature sensors based on Fabry-Perot interferometer made with polymer technology.

Nanometer-curved surfaces are abundant in biological systems as well as in nano-sized technologies. Properly functionalized polymer-grafted nanoparticles (PGNs) adhere to surfaces with different geometries and curvatures. This work explores some of the energetic and mechanical characteristics of the adhesion of PGNs to surfaces with positive, negative and zero curvatures using Coarse-Grained Molecular Dynamics (CGMD) simulations. Our calculated free energies of binding of the PGN to the curved and flat surfaces as a function of separation distance show that curvature of the surfaces critically impacts the adhesion strength. We find that the flat surface is the most adhesive, and the concave surface is the least adhesive surface. This somewhat counterintuitive finding suggests that while a bare nanoparticle is more likely to adhere to a positively curved surface than a flat surface, grafting polymer chains to the nanoparticle surface inverts this behavior. Moreover, we studied the rheological behavior of PGN upon separation from the flat and curved surfaces under external pulling force. The results presented herein can be exploited in drug delivery and self-assembly applications.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

Hybrid inorganic-polymer nanocomposites can be employed in diverse applications due to the potential combination of desired properties from both the organic and inorganic components. The use of novel bottom-up in situ synthesis methods for the fabrication of these nanocomposites is advantageous compared to top-down ex situ mixing methods, as it offers increased control over the structure and properties of the material. In this review, the focus will be on the application of the sol-gel process for the synthesis of inorganic oxide nanoparticles in epoxy and polysiloxane matrices. The effect of the synthesis conditions and the reactants used on the inorganic structures formed, the interactions between the polymer chains and the inorganic nanoparticles, and the resulting properties of the nanocomposites are appraised from several studies over the last two decades. Lastly, alternative in situ techniques and the applications of various polymer-inorganic oxide nanocomposites are briefly discussed.

Polymer nanocomposites are composed of polymer materials reinforced with nano fillers. In the present study the effective thermal conductivity of the composites filled with nanofillers has been investigated using commercially available finite element software ABAQUS 6.11. The nanofillers used were alumina particles and multi-walled carbon nanotubes (MWNTs) and the matrix was considered to be made of epoxy. For the analysis 2D and 3D Representative Volume Elements (RVEs) were generated using Random Sequential Adsorption (RSA) algorithm using MATLAB and Python scripts. Thermal conductivity was found out for 2D and 3D RVEs for different area and weight fractions respectively. Two different shapes of the alumina nanoparticles were considered: spherical (circular) and ellipsoidal (elliptical) for 3D (2D) analysis. It was found that the thermal conductivity was increased with the addition of nanofillers. The increase in thermal conductivity was approximately same for both types of inclusions at corresponding area or weight fractions in 2D or 3D analysis. The results showed that addition of MWNTs to the composites lead to a significant increase in thermal conductivity than spherical or ellipsoidal inclusions.

Lithium-ion batteries (LIBs) have become indispensable energy storage devices for various applications, ranging from portable electronics to electric vehicles and renewable energy systems. The performance and reliability of LIBs depend on several key components, including the electrodes, separators, and electrolytes. Among these, the choice of binder materials for the electrodes plays a critical role in determining the overall performance and durability of LIBs. This review introduces polymer binders that have been traditionally used in the cathode, anode, and separator materials of LIBs. Furthermore, it explores the problems identified in traditional polymer binders and examines the research trends in next-generation polymer binder materials for lithium-ion battery as alternatives.

The selection of biomaterials for biomedical application is a significant challenge. In the last few decades, various bioabsorbable and stable biopolymers have been applied for use as biomedical devices in orthopedic applications. Ultra-high molecular weight polyethylene (UHMWPE) has been extensively used in medical implants, notably in the bearings of hip, knee, and other joint prostheses, owing to its biocompatibility and high wear resistance. For the ACL graft, synthetic UHMWPE is an ideal candidate due to its biocompatibility and its extremely high tensile strength. Despite the appeal of new advanced materials such as carbon fiber, poly-ether-ether ketone, and other load-bearing materials, UHMWPE remains a primary load-bearing candidate material for ACL reconstructions because of its extremely high strength, the simplicity of the fabrication process, its biocompatibility, and low friction. However, some significant problems are observed in UHMWPE based implants, such as wear debris, and oxidative degradation due to the generation of free radicals when exposed to irradiation with gamma rays for grafting or sterilization. Various innovative methodologies have been developed to resolve those problems and enhance the properties of UHMWPE. In this review, we will explore in detail the methods for surface functionalization of UHMWPE and will apply these findings to the case study of UHMWPE for Anterior Cruciate Ligament repair.

In this scientific research, thermally stable nickel nanoparticles were synthesized and characterized. Nickel nanoparticles were synthesized using phenol –formaldehyde by chemical method followed by calcination. The polymer metal complex was confirmed by FTIR and NMR. The spherical morphology of nickel nanoparticles confirmed by SEM. The crystallographic structure is confirmed by XRD and size of cobalt nanoparticles is 24.0 nm. The TGA analysis was performed over a range of 29-600OC. The TGA thermograph predicts mass decomposition of 11%, for nickel phenol-formaldehyde nanocomposite. The decomposition rate of composites is very low 2% weight loss per 100OC increment in temperature.

Herein, we present preparation of solid polymer electrolyte (SPE) comprising of PEO, NaPF₆ and varying fraction of Succinonitrile (SN) by standard solution cast technique. The morphological features and structural properties were studied by the FESEM, XRD, respectively. FTIR was performed to study the interactions between polymer host, salt, and SN. Impedance spectroscopy, Transference number measurements, LSV and CV were used to examine the electrochemical properties. The complex permittivity/conductivity & modulus were studied to understand the dielectric properties by evaluating the dielectric strength, relaxation time, hopping frequency and dc conductivity. Based on the experimental results an interaction mechanism is presented.

Solar concentration is the ability to harness solar radiation to increase the temperature of a receiver. The receiver is the component into which a heat transfer fluid can be flowed for an ORC system and produce electricity, or it can be used for high-temperature thermal storage, or even to implement thermochemical cycles. The choice of material is critical to ensure optimal performance and long-lasting operation. It is also essential that such material can operate at high temperatures and high thermal gradients. In short, material identification involves high thermal stresses that result in structural deformation. Different metal alloys were used to verify that the yield strength limit was not exceeded due to thermal stress induced by concentrated solar radiation. The problem was implemented in Matlab starting from the general heat equation. The purpose is to test whether thermal stress exceeds the yield strength, which is the condition in which elastic bonds in the material are changed, causing deformation. The best material identified was Inconel 740H, which had a high yield strength value and the lowest temperature difference. Under extreme working conditions, it can withstand thermally induced shocks.

The main goal of this study was to evaluate sugarcane bagasse ash as a partial cement replacement material. Sugarcane bagasse ash is a by-product of fuel blending in the sugar industry. Yet all economic sugar is obtained after extraction from the cane. The disposal of the discharged waste in agriculture causes environmental problems in the sugar industry. The cement industry also creates environmental problems due to carbon dioxide emissions during cement manufacturing. Initially, bagasse ash samples were collected from the rubble of the Arjo Didessa sugar factory. The crude bagasse ash was sieved with a sieve size of 250µm. The strength of grade C-25 concrete was designed using five different concrete mixture proportions ranging from 5 to 20% cement by weight, including a water-cement ratio of 0.45. Impact strength tests were conducted at 7, 14, 21, and 28 days of age for each replacement ratio. For the experimental work, a total of 60 cubic concrete specimens were cast for compressive strength tests, and 15 cylindrical concrete specimens were cast for water absorption tests. Working compressive strength results indicated that bagasse ash could replace up to 5% of ordinary Portland cement concrete.

Highlights: A new material with a bending strength higher than that of concrete was developed using vegetable or fruit waste. The new material maintains the color, taste, and flavor of the original vegetable or fruit. Without water resistant treatment, the material is edible and can be conditioned with seasonings

The material derivative is important in continuum physics. This Letter shows that the expression $\frac{d }{dt}=\frac{\partial }{\partial t}+(\bm v\cdot \bm \nabla)$, used in most literature and textbooks, is incorrect. The correct expression $ \frac{d (:)}{dt}=\frac{\partial }{\partial t}(:)+\bm v\cdot [\bm \nabla (:)]$ is formulated. The solution existence condition of Navier-Stokes equation has been proposed from its form-solution, the conclusion is that "\emph{The Navier-Stokes equation has a solution if and only if the determinant of flow velocity gradient is not zero, namely $\det (\bm \nabla \bm v)\neq 0$.}"

Sensory evaluation has been widely applied in assessing the quality of many consumer products that directly serve human needs such as food, beverages, clothing, etc. This paper first examined the inherent deficiencies in this approach, due mainly to the essentially subjective nature of human sensory preference. It then argued that instinctively designating certain materials attributes as sensory perceptions is unnecessary; considering every scientific concept is in essence the processed results of our sensory organs/brains, i.e., all quantities were initially human perceptions. Scientific advances have inevitably generated gradual transformation of such human perceptions as warmth and heaviness into objective parameters measurable in physical quantities like temperature and kilograms. Then using existing successful examples, it demonstrated firmly how the sensory attributes can be assessed by more reliable instrumental methods, and envisioned the key steps to turning a perception into scientifically measurable parameter(s).

With the emergence of autonomous functions in road vehicles, there has been an increased use of Advanced Driver Assistance Systems comprising various sensors to perform automated tasks. Light Detection and Ranging (LiDAR) is one of the most important types of optical sensor that detects the positions of obstacles, representing them as clusters of points in 3-dimensional space. LiDAR performance degrades significantly when driving in rain as raindrops adhere to the outer surface of the sensor assembly. The performance degradation behaviors include missing points and reduced reflectivity of the points. It was found that the extent of degradations is highly dependent on the interface material properties, which subsequently affects the shapes of the adherent droplets, causing different perturbations to the optical rays. A fundamental investigation is performed on the protective polycarbonate cover of the LiDAR assembly coated with four classes of materials – hydrophilic, almost-hydrophobic, hydrophobic, and superhydrophobic. Water droplets are controllably dispensed onto the cover to quantify the signal alteration due to each droplet of various sizes and shapes. To further understand the effects of droplet motion on LiDAR signals, sliding droplet conditions are simulated using numerical analysis and validated with physical optical tests using a 905 nm laser source and receiver to mimic the LiDAR detection mechanism. Comprehensive explanations are presented on LiDAR performance degradation in rain from both material and optical perspectives. These can aid component selection and the development of signal enhancing strategies for integrating LiDARs in vehicle designs to minimize the impact of rain.

Abstract: The centrepiece of this analytical review is the metabolism of hydroxyapatite in its natural, bone, and synthetic forms, where the mitochondria-mediated mechanism may serve as the leading mechanism. The possibility that osteoblast mitochondria play an important role in the initial stages of bone mineralisation is discussed. Furthermore, the paper highlights the key role of mitochondria in the metabolism of synthetic hydroxyapatite.Differences between the results of in vivo and in vitro studies using synthetic hydroxyapatite of different morphologies are also detailed. It is noted that long-term infiltration with immune cells and in vivo studies are necessary to adequately evaluate hydroxyapatite as a bone-plastic material.Particular attention is given to the interaction of hydroxyapatite with immune cells and its ability to affect the ribosomes and mitochondria of cells. Due to its mechanical properties, scalability and potential use for the treatment of extensive bone defects of tumor origin, hydroxyapatite is a promising material.This study also highlights the importance of further development of in vitro research methods in the context of their biomimeticity. Overall, this work offers a theoretical direction for future studies of hydroxyapatite as a bone grafting material and emphasises the value of in vivo studies.

Recently, Electric Two-Wheelers ETW are changing the face of the global automotive market. This study focused on selecting proper material and mechanical isolation gap to design a protective enclosure for the battery pack of ETW. The integration of the Failure, Modes, Mechanism and Effect Analysis (FMMEA) method is utilized to develop the interface matrix and the severity index of different components of the enclosure. By analyzing different forces from the road conditions, dynamics during turn, acceleration, and deceleration with the enclosure, it becomes a crucial load-bearing element. Employing Finite Element Modeling (FEM), structural strength using materials like AL6061, Q235, C22000, DC 01 and Teflon are assessed under varying static, dynamic and thermal conditions. Modal analysis is conducted to observe the excitation frequencies where the maximum deformation for the metal enclosure is observed beyond 500Hz. AL6061 material that can withstand the stresses and deformations that are under allowable stress limits with negligible deformation is most preferable material based on the results. Minimal of 2.5 mm gap to be provided in case of metal casing and 10mm in case of Teflon is proven.