In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

The month of May 2024 was characterized by solar energetic particles events directed towards the Earth, especially the big event causing a strong terrestrial geomagnetic storm during the night from 10 to 11 May 2024, with auroras observed everywhere in Europe. This was the strongest storm for the last 20 years with a Dst < -400 nT. In the present work, we show with observations of GOES, PROBA-V/EPT and MetOP/MEPED that this exceptional event was associated with the injection of energetic protons in the proton radiation belt, with important consequences for the South part of the South Atlantic Anomaly (SAA). In addition, the geomagnetic storm caused by the solar eruption has had tremendous impacts on the electron radiation belts. Indeed, we show that for 0.3 to 1 MeV electrons, the storm led to a long lasting four belts configuration which was not observed before with EPT launched in 2013, until a smaller geomagnetic storm on June 15 took place. Moreover, for the first time since its launch, observations of the EPT show that ultra-relativistic electrons with E>2 MeV have been injected into the inner belt until L=2.4, violating the impenetrable barrier previously estimated to be located at L=2.8.

The effect of doublet state metalloradical complex in a solar cell inside the common active layer poly(3-hexylthiophene)/ [6,6]-phenyl-C61-butyric acid methyl ester (P3HT/PC60BM) is explored. In this work is demonstrated that the role of the Bis-[1,3-Bis-(2,6-diisopropylphenyl)-4,5-dichloroimidazol-2-ylidene]palladium(I) hexafluoridophosphate dopant, [Pd(IPrCl)2][PF6], is crucial because, by having a stable unpaired electron in the molecule, it significantly improves the optoelectronic performance of the devices. We found the optimal concentration of this molecule in the active layer, and we demonstrated that the presence of this additive in the active layer helps to significantly improve the morphology of the device. The improvements in optoelectronic and morphological parameters are associated with a remarkable increase of photocurrent generation due to more favourable mechanisms of charge separation at the donor/acceptor (D/A) interfaces of the active layer and reduced recombinations. Moreover, the presence of this additive improves the stability of the unencapsulated solar cell against photochemical degradation produced by sunlight.

The power conversion efficiency (PCE) of polymer solar cells (PSCs) are strongly depended on the bulk-heterojunction active layer. Here, the 1,8-diiodooctane (DIO) additives have been added into the PCDTBT: PC70BM blend PSCs. Based on the higher boiling point than host solvent ODB and better solubility of PC71BM, the device photovoltaic properties with DIO additive were changed obviously. The investigations of EQE indicate that the DIO can influence the charge recombination and transportation process, and absorption studies demonstrate that the charge carriers generation process can also be affected by DIO. The overall impact reflected on the decreased equivalent resistant. With 3% v/v DIO, the Jsc, Voc and FF are both increased. Correspondingly, a highest PCE is achieved of 6.15%, while the reference device without DIO only has a PCE of 5.23%. Hence, adding DIO solvent additive is a effective method for the photovoltaic properties improving of PCDTBT: PC70BM blend PSCs.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

The article offers a comprehensive overview of recent breakthroughs in eco-friendly polymers and polymer composites, underscoring their pivotal role in addressing sustainability challenges across diverse industrial sectors. Despite encountering obstacles related to performance and processability, biopolymers sourced from renewable materials emerge as promising alternatives for the plastics that are currently used by human beings. Natural fillers are highlighted as a strategic avenue for crafting sustainable composites, with residual natural fillers being particularly explored. Heightened environmental concerns propel discussions on the criticality of integrating biodegradable materials with natural fillers, underlining the urgency for clear frameworks and financial incentives to support adoption of these materials. Additionally, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on the utilization of polyhydroxyalkanoate (PHA) in composite materials and its market prospects. Moreover, it emphasizes the indispensable need for ongoing research and development endeavors to address environmental challenges within the polymer sector, reflecting a mounting interest in sustainable materials across industries.

Two region asymmetric polymers PR2F and PR1F with three repeat units of A-D-A, π-D-A, and π-D-π along the polymer backbone were attained by polymerizing different fluorinated benzothiadiazole-thiophene units, FBT-T and 2FBT-T units (A–π), with benzodithiophene unit (D), respectively. Here, the new region asymmetric polymers were in contrast to the traditional polymers featuring a D–A or D–π–A–π backbone. Both the region asymmetric polymers showed a low lying of HOMO energy level in relation to that of the PC61BM acceptor and then obtained the high open-circuit voltage of ~1 V in both PR2F and PR1F devices. Bulk-heterojunction devices based on PR2F with difluorinated BT exhibited an appreciable power conversion efficiency (PCE) of 4.73% due to the relatively high and balanced charge carrier mobilities, while the mono-fluorinated BT polymer PR1F-based devices gave a lower PCE of 2.92%. These results indicate that the region asymmetric conjugated polymer is a promising class of materials for polymer solar cell applications, and it is significant to further understand the influence of polymer structure on optoelectronic properties.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Dehydration of hydrogen gas is one of the important steps in many industrial purposes thus, drying systems have been developed with high-efficiency and relative effect. In this article, the basic principles and design of a three-bed TSA (Temperature Swing Adsorption) dryer for dehydration operation of hydrogen gas drying are described in detail. The text commences with an in-depth explanation of the basic principles behind TSA technology such as adsorption and desorption mechanisms, thermodynamic considerations and material selection for adsorbents. This paper also deals with the detailed design of a three-bed TSA dryer, explaining about various fabricating details that influences both performance and total operability. The third part focuses the operational phase, and especially in cycle time, regeneration strategy and efficiency of energy. Advanced optimisation techniques are employed to lower energy consumption, increase throughput capacity and improve overall system. This detailed study will be of great help for engineers and investigators working on TSA systems design and optimization to dehydrate hydrogen gas, contributing towards the betterment in this important field dealing with industrial gas processing.

At present, the world is now passing a very far different time than normal situation due to the COVID-19 pandemic crisis. The global life-style and human civilization is currently progressing with down-stream that affecting almost every sectors necessary for human civilizations except the current environmental situation. To control the COVID-19 spreading, most of the countries are following lockdown process that reduces human mobility, thus reducing the CO2 emission to the environment. Though the COVID-19 pandemic is a blessing for the present environment, however, the post-COVID world will face a massive thrust of energy and only conventional energy resources may not be enough to mitigate the energy demands. Solar power generation technology mainly the photovoltaic (PV) systems and their advancement can be the leading possibilities to minimize the gap between the power demand and generation. It is now time to think how we can improve the PV power generation in future and the post-COVID world. In this encyclopaedia communication, we report on Nano-technological approach to improve the conversion efficiency of GaAs solar cells. We have designed and optimized several types of nano-structured assemblies that can be implemented to reduce the front surface incident light reflection losses thus can assist to improve the conversion efficiency of GaAs solar cells.

This study presents an advanced defect detection approach for solar cells using the YOLOv10 deep learning model. Leveraging a comprehensive dataset of 10,500 solar cell images, annotated with 12 distinct defect types, our model integrates Compact Inverted Blocks (CIB) and Partial Self-Attention (PSA) modules to enhance feature extraction and classification accuracy. Training on the Viking cluster with state-of-the-art GPUs, our model achieved remarkable results, including a mean Average Precision ([email protected]) of 98.5%. Detailed analysis of the model's performance revealed exceptional precision and recall rates for most defect classes, notably achieving 100% accuracy in detecting black core, corner, fragment, scratch, and short circuit defects. Even for challenging defect types such as thick line and star crack, the model maintained high performance with accuracies of 94% and 96%, respectively. The recall-confidence and precision-recall curves further demonstrate the model's robustness and reliability across varying confidence thresholds. This research not only advances the state of automated defect detection in photovoltaic manufacturing but also underscores the potential of YOLOv10 for real-time applications. Our findings suggest significant implications for improving the quality control process in solar cell production.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP:PMMA or BCP:PVP/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

In a previous study we could show a change of membrane morphology and gas separation performance by varying the recipe of a casting solution based on polysulfone in a determined solvent system. Although all results were very reproducible, all used solvents were harmful and not sustainable. In this study therefore, the solvents tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAc) are replaced by the more sustainable solvents 2-methyl-tetrahydrofuran (2M-THF), N-butyl pyrrolidinone (NBP) and cyclopentyl methyl ether (CPME). The gas permeation performance and for the first time morphology of the membranes before and after solvent replacement were determined and compared by single gas permeation measurements and SEM microscopy. It is shown, that THF can be replaced by 2M-THF and NBP without decreasing the gas permeation performance. With CPME replacing THF no membranes were formed. Best gas permeation results showed systems with 2M-THF as THF alternative. Permeances for the tested gases oxygen (O2), nitrogen (N2), carbon dioxide (CO2) and methane (CH4) were 2.66·10-4, 3.89·10-5, 1.53·10-3 and 4.52·10-5 mL(STP)/cm²·min·bar, respectively. permselectivities of those membranes for the gas pairs O2/N2, CO2/N2 and CO2/CH4 were 6.7, 38.3 and 34.0, respectively. When additionally replacing DMAc in the solvent system no or only porous membranes were obtained, even if the precipitation procedure was adjusted. These findings indicate that a complete replacement of the solvent system without affecting the membrane morphology or gas permeation performance is not possible. By varying the temperature of the precipitation bath an easy adjustment to mechanically stable PSU membranes is possible, if just THF was replaced by 2M-THF.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, polymer D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via LBL fabrication method in regulating microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

The reduction of PV prices and interest in energy independence accelerate the adoption of residential battery storage. This storage can support various functions of an energy system undergoing decarbonization. In this work, operative benefits of the storage from the system perspective, namely, generation cost reduction and congestion mitigation, are investigated. Germany is chosen as a case study due to its strong reliance on variable renewable energy. For the analysis, an economic dispatch model with a high spatial resolution is coupled with a Pan-European transmission grid model. It is shown that the system's generation costs are highest when the assets are used only to maximize the PV self-consumption, and the costs are lowest when the storage also reacts to the market dynamics. This amounts to 6% cost reduction. Both operation strategies result in an equal level of grid congestion and infrastructure loading. This is improved with a strategy that accounts regional peak reduction as a secondary objective. The high congestion level emphasizes the grid expansion need to keep pace with the generation and electrification expansion necessary to decarbonize other sectors. Lastly, policymakers should enable multipurpose utilization, e.g., via the introduction of market-oriented retail electricity prices with intervention options for grid operators.

Dye-sensitized solar cells (DSSCs) belong to the group of thin-film solar cells which have been extensively researched for over two decades due to their low cost of fabrication, flexibility and ability to function under low-light conditions. Some issues have to be addressed in terms of energy losses, material integration, weak photocurrent generation and stability to improve the performance of DSSCs. One of the approaches to enhance the performance of DSSCs is through luminescent materials. These are materials which can absorb light and re-emit at different wavelengths which can be used to convert ultraviolet (UV) and near infra-red (NIR) light that are not efficiently utilized by the DSSCs, into visible light that can be absorbed. The main objective of this article is to provide a comprehensive review on the impact of luminescent materials in DSSCs. Research interest in luminescent materials particularly, down conversion, up conversion and quantum dots were analyzed from the “Web of Science”. It reflected a remarkable number of over 200, 000 publications in the past decade. Therefore, the state of the art of luminescent materials for enhancing the performance of the solar cells were reviewed, which showed significant potential in enhancing the performance of DSSCs.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

Wood-borer extermination by a dry heat clean-up is the essential method from the point of view of sustainability of historical wooden structures like trusses and ceilings in heritage-listed buildings. The wooden components are heated by a hot air of temperature about 100°C until the temperature in the centre of the wooden structures reaches 55°C to kill the wood-borers. In this article we review the method and present solution of the heat equation for structural wooden components. We also suggest an approximate formula that enables to estimate the necessary heating time for different cross sections of wooden components and can be used in technical application of the method.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

The objective of this research project was to evaluate the effects of the addition of inorganic fillers into PEBA at various loading levels on the processing, mechanical, thermal and physical properties of the polymer. The composites investigated in this study were Pebax® 6333 SA01 MED (PEBA100) with 10 wt.%, 20 wt.% and 30 wt.% Barium Sulphate (PEBA/BaSO4) and Bismuth Oxychloride (PEBA/BiOCl) respectively. Composites were prepared using twin screw extrusion and injection moulding. Post-processing, composite samples were analysed for their mechanical properties (via tensile, impact and flexural analysis), thermal properties (via differential scanning calorimetry), rheological performance (via melt flow index) and physical properties (via density analysis and ash content testing). The results of which reveal how filler type and concentration influence PEBA composites. The results of the study suggest that BiOCl filler enhances the aesthetic properties, increases the stiffness, while maintaining some level of flexibility with minimal adverse effects on the tensile and impact strength. When comparing BiOCl to BaSO4 filled composites, it was clear that depending on the application of the polymer composite, BiOCl may provide more desirable properties. The study highlights the importance of optimising filler concentration and processing conditions to achieve desired composite properties for specific medical applications.

The goal of this work was to develop the acrylonitrile-butadiene (NBR) elastomer composites filled with hydroxyapatite (HAP), which were characterized with improved cure characteristics and burning resistance. Silane, i.e., (3-aminopropyl)-triethoxysilane, ionic liquid, i.e., 1-decyl-3-methylimidazolium bromide and surfactant, i.e., cetyltrimethylammonium bromide, were used to improve the filler’s dispersibility in the elastomer matrix and to reduce the time and temperature of vulcanization. The effect of HAP and dispersants on the cure characteristics, crosslink density and physico-chemical properties of NBR composites was explored. The additives used, especially the ionic liquid and surfactant, effectively improved the dispersion of HAP in NBR matrix. The amount of HAP and the dispersant used strongly affected the cure characteristics and crosslink density of NBR. The optimal vulcanization time significantly increased with HAP content and was pronouncedly reduced when ionic liquid and surfactant were applied. In addition, ionic liquid and surfactant significantly lowered the onset vulcanization temperature, improved the crosslink density and hardness of the vulcanizates, while impairing their elasticity. HAP and dispersants did not significantly affect the damping properties and chemical resistance of NBR vulcanizates. Above all, application of HAP considerably enhanced the resistance of vulcanizates to thermo-oxidative aging and reduced their flammability compared to the unfilled NBR.

We report on the effects of the film morphology on the fluorescence spectra for a thin film including a quinoxaline-based co-polymer (TQ1) and a fullerene derivative (PC₇₀BM). The ratio between the polymer and the fullerene derivative, as well as the processing solvent were varied. Beside the main emission peak at 700 nm in the fluorescence spectra of thin films of this phase-separated blend, a broad emission band is observed with a maximum at 520 - 550 nm. The intensity of this emission band decreases with an increasing degree of mixing in the film and becomes most prominent in thicker films, films with high PC₇₀BM content, and films that were spin-coated from solvents with lower PC₇₀BM solubility. We assign this emission band to aggregated PC₇₀BM.

Due to the optical properties of the Electron Transport Layer (ETL) and Hole Transport Layer (HTL), inverted perovskite solar cells can perform better than traditional perovskite solar cells. It is essential to compare both types to understand their efficiencies. In this article, we studied inverted perovskite solar cells with NiOx/CH3NH3Pb3/ETL (ETL = MoO3, TiO2, ZnO) structures. Our results showed that the optimal thickness of NiOx is 80 nm for all structures. The optimal perovskite thickness is 600 nm for solar cells with ZnO and MoO3, and 800 nm for those with TiO2. For the ETLs, the best thicknesses are 100 nm for ZnO, 80 nm for MoO3, and 60 nm for TiO2. We found that the efficiencies of inverted perovskite solar cells with ZnO, MoO3, and TiO2 as ETLs, and with optimal layer thicknesses, are 30.16%, 18.69%, and 35.21%, respectively. These efficiencies are 1.5%, 5.7%, and 1.5% higher than those of traditional perovskite solar cells. Our study highlights the potential of optimizing layer thicknesses in inverted perovskite solar cells to achieve higher efficiencies than traditional structures.

The surface characterization of indium tin oxide (ITO) films was processed by oxygen (O2) plasma gas using a magnetron sputtering method of varying O2-plasma gas from 20 sccm to 100 sccm for potentially fostering in electronic devices applications on dye-sensitize solar cells (DSSC) in this work. In order to gain an outstanding performance rate with high-quality thin films, the affect of correlation between the electrical, optical, and morphology properties was significantly investigated. Clearly, the content of investigation exhibited that the films properties was changed by variation of the gas composition. These changes have contemporary relevance to the sputtering gas during the deposition process. To conclude, the greatest electrical properties was displayed by O2 -plasma gas flow rate of 20 sccm, which showed the lowest resistivity. In addition to this, the final products were practically fabricated to active layers for dye-sensitize solar cells (DSSC) applications. The highest efficiency of DSSC device was indicated of approximately 0.35% which was located by 40 sccm of the O2-plasma gas. Consequently, the study could be a possibility way of preparing ITO thin films with improved special properties of substantial applications for solar cells devices in the near future.

Perovskite-silicon tandem solar cells represent a significant advancement in photovoltaic technology, aiming to overcome the efficiency limitations of traditional silicon-based solar cells. This paper explores recent developments in the fabrication and optimization of these tandem cells, focusing on improving both efficiency and long-term stability. The combination of perovskite materials with silicon allows for broader spectrum absorption, which enhances the overall power conversion efficiency. Key strategies include optimizing the perovskite layer's composition, improving the interface between layers to reduce recombination losses, and incorporating advanced encapsulation techniques to mitigate degradation from environmental factors such as moisture and UV exposure. The review also highlights the challenges faced in scaling up production while maintaining high performance and stability. Emerging trends in material engineering and device architecture are discussed, providing insights into future directions for making perovskite-silicon tandem solar cells a viable commercial technology. This study underscores the potential of these hybrid systems to significantly boost the efficiency of photovoltaic systems, offering a promising pathway towards more sustainable and costeffective solar energy solutions.

Photovoltaic is one of the promising renewable sources of power to meet the future challenge of energy need. Organic and perovskite thin film solar cells are an emerging cost-effective photovoltaic technology because of low-cost manufacturing processing and a light-weight. The main barrier of commercial use of organic and perovskite solar cells is the poor stability of devices. Encapsulation of these photovoltaic devices is one of the best ways to address this stability issue and enhance the device lifetime by employing materials and structures that possess high barrier performance for oxygen and moisture. The aim of this review paper is to find different encapsulation materials and techniques for perovskite and organic solar cells according to the present understanding of reliability issues. It discusses the available encapsulate materials and their utility in limiting chemicals such as water vapour, oxygen penetration. It also covers the mechanisms of mechanical degradation within the individual layers and solar cell as a whole, and possible obstacles to their application in both organic and perovskite solar cells. The contemporary understanding of these degradation mechanisms, their interplay and their initiating factors (both internal and external) are also discussed.

The tandem Solar cell has high power conversion efficiency (PCE), so they are taken as the next step in photovoltaic evolution. The tandem solar cell also overcome the limitations of Single-junction solar cells by reducing thermalization losses and also reduce the fabrication cost. The fabrication of tandem solar cells is highly efficient after the origination of halide perovskite absorber material, this material will shape the future of tandem solar cells. Researchers have already shown that this material can convert light more efficiently than standalone sub cell. Today, researchers around the world are keeping the configuration of a tandem solar cell as their agenda. A Tandem solar cell is a stacking of multiple layers having different bandgaps with specific maximum absorption and width. We reviewed perovskite/silicon tandem solar cells with different sub-module configurations. Move forward, we discuss the tandem module technology, sub cell of a tandem can be wired in several ways two terminals 2T monolithic and mechanically stacked, a four-terminal 4T mechanically stacked, and three-terminal 3T monolithic stack devices. This review paper provides a side-by-side comparison of theoretical efficiencies of multijunction solar cells. The highest efficiency has been evaluated at 39.4% for a three-level structure.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

Interface solar steam generation (ISSG) are charming for its applications in desalination and wastewater treatment. Biomass is an attractive substrate for utilizing solar vapor evaporators because of its natural pore structure and water transportability. Polymers like polydopamine (PDA) and polypyrrole (PPy) with broadband spectrum absorption are fascinating in photothermal materials (PTMs). Herein, PDA coated daikon-based (PDA-DK) and PPy coated daikon-based (PPy-DK) PTMs have been exploited for solar steam generation. When polyethylene foam (PEF) was used as an insulating layer to limit heat loss from the PTMs to bulk water, the evaporation rate of PDA-DK and PPy-DK was raised from 0.82 kg m–2 h–1 and 0.96 kg m–2 h–1 to 1.50 kg m–2 h–1 and 1.60 kg m–2 h–1, respectively. Meanwhile, the corresponding photothermal conversion efficiency was increased to 89.01% and 98.97%, which was increased by nearly 40% under 1-sun irradiation. In addition, PDA-DK and PPy-DK exhibited remarkable stability for the solar steam generation without significant change through 15 cycles. Furthermore, PDA-DK and PPy-DK could effectively desalt seawater and purify dyeing wastewater. All the results indicate that PDA-DK and PPy-DK have great potential in real-world applications for solar steam generation.

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.

The aim of this study is to characterize the compound extremes of rainfall and temperature in Côte d’Ivoire. For this purpose, we analyzed the outputs of fourteen (14) climate models from the CORDEX-Africa project. Results show an increase (approximately 4.3°C) of the surface temperature and a decrease (5,90 %) of the mean rainfall in the near (2036-2065) and far futures (2071-2100) over Côte d’Ivoire during January-February-March (JFM) period. The analysis of the compound extremes of wet/warm type highlights an increase in the frequency of this climatic hazard in the northern and central parts of the country during January-March (JFM) season in the near and far futures. The dry/warm mode will increase in the central and southern parts of the country during the near future and in the whole country during the far future. These increase in compound extremes could lead to an increase in droughts and natural disasters over the country and could have a negative impact on socio-economic activities, such as transportation and agricultural production. This work could provide decision support for political decision-makers in formulating future public policies for managing agricultural production, food security, and natural disasters.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

This paper presents a comprehensive evaluation of metal foam employment within polymer electrolyte fuel cells (PEFCs) and compares it with conventional serpentine channels from both experiment viewpoints and computational fluid dynamics simulation. The experiments are designed to study the effects of material, area density, compression ratio, and final thickness of metal foam. Additionally, the influence of housing plate material and relative humidity (RH) is also tested for the first time. The results reveal that at RH=75-100%, the best distributor design is nickel foam with a compression ratio of 70%, a final thickness of 0.5mm, and SS-304 housing plate, which delivers 3110 mA cm^-2 as limiting current density that is scarce in the literature. The PEFC with this foam distributor shows a 10% improvement in maximum power density and 45% in limiting current density compared to the serpentine channel case. While at RH=30%, the same foam flow field with a final thickness of 1mm is a superior option. The experiments also indicate that maximum power density increases by 23% as the compression ratio rises from 0 to 70%, while reducing final thickness from 1 to 0.5 mm causes a 19% enhancement in cell performance. Simulation results reveal that metal foam is more successful in evenly reactant distribution so that the average oxygen mass fraction at the cathode catalyst layer is increased by 38% in the metal foam case compared to the serpentine channel.

The present investigation highlights the synthesis of polyaniline (PANI) coated graphene oxide doped with SrTiO3 nanocube nanocomposites through facile in-situ oxidative polymerization method for the efficient removal of carcinogenic dyes, namely, the cationic dye methylene blue (MB) and the anionic dye methyl orange (MO). The synthesised nanocomposites were characterised by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adsorption efficiencies of graphene oxide (GO), PANI homopolymer and SrTiO3 nanocubes-doped nanocomposites were assessed by monitoring the adsorption of methylene blue and methyl orange dyes from aqueous solution. The adsorption efficiency of nanocomposites doped with SrTiO3 nanocubes were found to be of higher magnitude as compared with undoped nanocomposite. Moreover, the nanocomposite with 2 wt% SrTiO3 with respect to graphene oxide demonstrated excellent adsorption behaviour with 99% and 91% removal of MB and MO respectively, in a very short duration of time.

The accurate prediction of heat load profiles with a daily resolution is required for a broad range of applications such as potential studies, design, or predictive operation of heating systems. If the heat demand of a consumer is mainly caused by (production) processes independent of the ambient temperature, existing load profile prediction methods fail. To close this gap, this study develops two ex post machine learning models for the prediction of the heat demand with a daily resolution. The selected input features are commonly available to each consumer connected to public natural gas and electricity grids or operating an energy monitoring system: Ambient temperature, weekday, electricity consumption, and heat consumption of the last seven days directly before the predicted day. The study’s database covers electricity and natural gas consumption load profiles from 82 German consumers over a period of two years. Electricity and heat consumption correlate strongly with individual patterns for many consumers. Both, shallow and deep learning algorithms are evaluated. The highest accuracy is achieved by a Long Short Term Memory (LSTM) model with a median of R² of 0.94. The ex post model architecture makes the model suitable for automated anomaly detection in energy monitoring systems.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

This paper deals with the problem of determining the optimal capacity of Concentrated Solar Power (CSP) plants, especially in the context of hybrid solar power plants. This work presents an innovative analytical approach to optimize the capacity of concentrated solar plants. The proposed method is based on the use of additional non-dimensional parameters, in particular the design factor and the solar multiple factor. The paper presents a mathematical optimization model that focuses on the capacity of concentrated solar power plants where thermal storage plays a key role in the energy source. The analytical approach provides a more complete understanding of the design process for hybrid power plants. In addition, the use of additional factors and the combination of the proposed method with existing numerical methods allows for a more refined optimization, which allows for a more accurate selection of the capacity for specific geographical conditions. Importantly, the proposed method significantly increases the speed of computation compared to traditional numerical methods. Finally, the authors present the results of the analysis of the proposed system of equations for calculating the levelized cost of electricity (LCOE) for hybrid solar power plants. The nonlinearity of the LCOE on the main calculation parameters is shown.

Different materials prepared by appropriate synthesis methods and applying different post syn-thesis processes could be used as hole transport layer in perovskite solar cells. In the present work annealing was employed to enhance physical properties of copper oxide (CuO) thin films fabricated via spin coating technique and the effects of annealing on their optical, morphological, electrical and structural properties were investigated. The XRD findings revealed the polycrystalline structure with large crystallite size. Optical spectra showed larger transmission beyond the visible region, reduced absorption, and a decrease in bandgap energy from 1.93 eV to 1.81 eV. The Ag phonon modes at 299.22 and 304 cm-1 shown by the Raman shift confirmed the development of the CuO pure phase. FTIR spectra showed the Cu-O stretching band at 759, 764 and 446 cm−1. SEM revealed the agglomeration of nano crystallites with large grains on the surface. The carrier type conductivity of annealed CuO thin films was determined via two-point hot probe technique. Low resistivity values were determined via four-point probe method. These findings indicate that CuO thin films may be successfully used as a companion with an n-type layer in p-n junction solar cells, and a hole transport layer in perovskite solar cells.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Three filamentous freshwater cyanobacterial strains were grown at high light intensity to produce lipidic dyes composed of xanthophylls, carotenes and chlorophyll a. The properties of the pigments were evaluated as suitable natural compounds to be applied in dye-sensitized solar cells (DSSC). The assembled DSSC were characterized using the density current vs. potential profiles and electrochemical impedance spectroscopy. With an efficiency of 0.127 %, our results are higher than those previously reported using similar structured compounds from natural sources as algae and cyanobacteria, among others. The best efficiencies were probably related to the strains with high content in pigments probably related to myxoxanthophyll-like derivates and aphanizophyll, carotenoids with many hydroxyl groups able to interact with the semiconductor surface. The stability of the bonding between the dyes and the titanium oxide of the photoelectrode is crucial to ensuring acceptable performance of the DSSC, which was successfully achieved in our experiments with carotenoids with many hydroxyl groups. Our results point to cyanobacterial pigments as a promising source of natural dyes for use in solar cells.

Perovskite Solar Cell (PSC) is a third-generation photovoltaic device known for its rapid improvement in efficiency levels over the past decade. Moreover, the added benefits of abundant sourcing of raw materials, uncomplicated fabrication process, organic and inorganic device materials, and tuneable bandgaps make this technology a sustainable energy alternative. However, the efficiency values of these devices are subjected to variation depending on factors such as material compatibility, environmental conditions, energy band alignment of device components and stability characteristics to extrinsic and intrinsic factors. One such vital intrinsic factor is film morphology, homogenous and superior film quality formation and pinhole and trap-free films. In this study, we have investigated the formation of perovskite films on a qualitative basis using metal chloride washing of salts such as Erbium, Antimony, Cadmium and Chromium Chloride. The study aims to analyse the difference in film formation with various metal chloride washing and how this could potentially impact or contribute to photovoltaic performance if the devices are fabricated.

We conducted this systematic review with the objective to understand the efficacy and safety of proton pump inhibitors [PPIs] in the pediatric population. We have used PubMed to identify randomized controlled trials [RCTs] published between 1st June 2010 and 30th June 2023, in patients from birth to 18 years old, with gastroesophageal reflux disease [GERD], who received treatment with any PPI. The literature yielded 76 articles and 13 met inclusion criteria. For infants, PPIs were equal to placebo in reducing GERD symptoms in 4 articles. In 1, the number of GER episodes and esophageal acid exposure were lower in infants who received PPIs and left lateral position, but there was no significant improvement in symptoms. In another publication, the combination of PPIs and feeding modifications [FM] was not more effective than PPIs alone. For children and adolescents, PPIs were effective in improving symptoms and achieving mucosal and histological healing, which was subsequently maintained. To conclude, PPIs are not effective to reduce symptoms related to GERD in infants, but are effective in older children, along with histological remission. Generally, PPIs are well tolerated, but it is important to not forget the possible adverse events [AE], especially if they are used for a long time.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O2 plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O2. Plasma production is stimulated with an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formation. The film preparation at RF power 300 W will give the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 x 10-4 Ω-cm. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. This is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.

Flexible polymer-based dye-sensitized solar cells (DSSCs) offer promising potential for lightweight, cost-effective and versatile photovoltaic applications. However, the critical challenge in their widespread applications is the weak thermal stability of the majority of polymeric substrates, which can only withstand a maximum temperature processing of 150°C. In this study, we propose a facile and low-cost strategy to develop at low temperature DSSC flexible photoanode based on a polymeric matrix. Highly porous nanocomposites fibrous mats composed of polyethylene terephthalate (PET) and titanium dioxide (TiO2) nanobars were prepared through electrospinning process using different configurations (uniaxial electrospinning, coaxial electrospinning, and electrospray-assisted electrospinning). These techniques enabled precise control of the microstructure and the positioning of TiO2 within the composite nanofibers. Therefore, the as-produced photoanodes were loaded with N719 dye and tested in DSSC prototype using iodide-triiodide electrolyte and platinum (Pt) coated counter electrode. The results show that incorporating TiO2 on the fiber surface through the electrospray-assisted electrospinning enhanced the performance of the nanofiber composite, leading to improved dye loading capacity, electron transfer efficiency and photovoltaic performance.

Developing low-cost and stable materials for converting solar energy into electricity is vital in meeting the world's energy demand. Metal-organic frameworks (MOFs) have gained attention for solar cells due to their natural porous architectures and tunable chemical structures. This review commences with an exploration of the synthetic methods of MOFs. Moreover, we discuss the various roles of MOFs, including photoanodes and counter electrodes in dye-sensitized solar cells and interfacial layers and charge carriers in perovskite solar cells. Ultimately, burdensome tasks and possible directions for advancing MOFs-based nanomaterials are provided for solar cells.

Hybrid lead halide perovskites have been revolutionary in the photovoltaic research field, reaching efficiencies comparable with the most established photovoltaic technologies, although they do not yet reach their competitor stability. The search for a stable configuration required the engineering of the charge extraction layers; in this work, molecular doping is used as an efficient method for small molecule and polymer, employed as hole transport materials in planar heterojunction configuration on compact-TiO2. We proved the viability of this approach, obtaining significantly increased performances and reduced hysteresis on compact titania-based devices. We investigated the photovoltaic performance, correlating to the hole transport material structure. We have demonstrated that the molecular doping mechanism is more reliable than the oxidative doping, and verified that molecular doping in polymeric hole transport materials leads to highly efficient perovskite solar cell, with long-term stability.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

Programmed cell death protein 1 (PD-1) is a biomarker on the surface of cells that has a role in promoting self-tolerance by suppressing the inflammatory activity of T cells. In this work, one peptide of PD-1 was used as the template in molecular imprinting. The magnetic peptide-imprinted poly(ethylene-co-vinyl alcohol) composite nanoparticles (MPIP NPs) were characterized by dynamic light scattering (DLS), high-performance liquid chromatography (HPLC), Brunauer-Emmett-Teller (BET) analysis and superconducting quantum interference device (SQUID) analysis. Natural killer-92 (NK-92) cells were added to these composite nanoparticles and then incubated with human hepatoma (HepG2) cells. The viability and apoptosis pathway of HepG2 were then studied using cell counting kit-8 (CCK8) and the quantitative real-time polymerase chain reaction (qRT-PCR), respectively. These nanoparticles were found significantly enhance the activity of natural killer cells toward HepG2 cells by increasing expression of NK-kB, caspase 8 and especially caspase 3.

Particle layers employing conductive transition metal nitrides have been proposed as possible alternative plasmonic materials for photovoltaic applications due to their reduced losses compared to metal nanostructures. We critically compare the photocurrent gain due to an additional layer made of nanopillars of nitrides with other material classes obtained in an already highly optimized doped c-Si baseline solar cell with accurate doping profile from measurements. A relative photocurrent gain with respect to the baseline cell of on average 5% to 10% is observed, with a few cases achieving around 30% gain. While the local field enhancement is moderate resonances for nitrides spread over the whole UV-VIS range. For some nitrides, the shading effect remains a problem similar as for metals, but others behave more like dielectric scatterers with high photocurrent gain.

In this paper, by developing a mathematical model, the operating temperature of perovskite solar cells (PSCs) under different operating conditions has been calculated. It is found that by reducing the density of tail states at the interfaces, acting as recombination centres, through some passivation mechanisms, the operating temperature can be reduced significantly at higher applied voltages. The results show that if the density of tail states at the interfaces is reduced by three orders of magnitude through some passivation mechanisms, then the active layer may not undergo any phase change up to an ambient temperature 300 K and it may not degrade up to 320 K. The calculated heat generation at the interfaces at different applied voltages with and without passivation shows that the heat generation can be reduced by passivating the interfaces. It is expected that this study may provide a deeper understanding of the influence of interface passivation on the operating temperature of PSCs.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

The efficiency of organic solar cells (OSCs) is influenced by various factors, among which environmental temperature plays a significant role. Previous studies have shown that the thermal stability of these cells can be enhanced by incorporating a third component into their structure. Ternary organic solar cells, in particular, have shown promising results in improving thermal stability. A well-designed electron transport layer (ETL) can significantly bolster thermal stability by facilitating efficient charge transport and reducing charge recombination. In this study, we investigated the effect of temperature on the efficiency of inverted ternary structures, ranging from 300 K to 400 K. The structures examined include FTO/SnO2/PM6:D18:L8-BO/PEDOT: PSS/Ag, FTO/Spiro-OMeTAD/PM6:D18:L8-BO/PEDOT: PSS/Ag, and FTO/PC60BM/PM6:D18:L8-BO/PEDOT: PSS/Ag. Through simulations employing three different electron transport layers—SnO2, Spiro-OMeTAD, and PC60BM—we observed that at 340 K (65°C) these structures maintained 92% of their original high efficiency of ~20% at 300 K, which represents a high level of thermal stability under the high PCE condition.

The stability issues in the widely known organic inorganic halide perovskite, CH₃NH₃PbI_3, lead to the development of alternative halide double perovskite materials which get great attention in recent times. Although the stability issue seems promising, both materials and device performance of these photovoltaic materials remain inferior and challenging for improvements. Furthermore, the power conversion efficiency of single junction organic inorganic halide perovskite is now 24.2% and 29.15% for textured monolithic perovskite/silicon tandem solar cell, but for all-inorganic halide perovskite solar cell is 7.11% and halide double perovskite solar cells based on Cs₂AgBiBr₆ and Cs₂TiBr₆ is 2.8% and 3.3%, respectively, which is far less than 24.2% and 29.15%, respectively. This creates big question and concern that can both all-inorganic halide perovskite solar cell and halide double perovskites solar cells really be an acceptable alternatives to replace organic inorganic halide perovskite solar cells or lead based perovskite solar cells in the market in order to realize the sustainable practical applications? Not only this concern, but also there are many other big challenges facing by halide double perovskite solar cells. Such big challenges include: a) geometric constraints and limited integration with interfacial materials, b) dynamic disorder and a wide band gap and localized conduction band caused by cubic unit cell which restrains the interactions of orbitals, c) high processing temperature which may limit on the diverse applications, d) low electronic dimensionality making them less appropriate for single junction solar cell purpose and etc. Moreover, origin of electronic and optical properties such as the polarizability, the presence of molecular dipoles and their influence on the dynamics of the photo-excitations in the halide double perovskites remains unlock concern that need to be elucidated. Now, another big question is how to develop overcoming mechanisms for such challenges. Can we really overcome these current limitations faced by halide double perovskites so that we use them for sustainable commercialization? This research roadmap for performance improvement is suggested focusing on: materials surface and bulk engineering, band gap engineering, interfacial engineering, composition engineering, doping engineering, device architectural engineering, polar and domain order engineering. This was the reason that this review was developed in order to forward great contributions to the readers and commercial ventures.

The perovskite solar cells (PSCs) have been significantly improved by utilizing inorganic hole transporting layer (HTL), such as nickel oxide. Despite the promising properties, there are still limitations due to defects. Recently, research on self-assembled monolayers (SAM) is being actively conducted, which show promise in reducing defects and enhancing device performance. In this study, we successfully engineered a p-i-n perovskite solar cell structure utilizing HC-A1 and HC-A4 molecules. These SAM molecules were found to enhance the grain morphology and uniformity of the perovskite film, which are critical factors in determining optical properties and device performance. Notably, HC-A4 demonstrated superior performance due to its distinct hydrophilic properties with a contact angle of 50.3°, attributable to its unique functional groups. Overall, the HC-A4 applied film exhibited efficient carrier extraction properties, attaining a carrier lifetime of 117.33 ns. Furthermore, HC-A4 contributed the superior device performance with its favorable band alignment, achieving the highest device efficiency of 20%.

The cutting-edge photovoltaic cells are an indispensable part of the ongoing progress of earth-friendly plans for daily life energy consumption. However, the continuous electrical demand that extends to the night time requires a prior deployment of efficient real-time storage systems. In this regard, metal-air batteries have presented themselves as the most suitable candidates for solar energy storage, combining extra lightweight with higher power outputs and promises of longer life cycles. Scientific research over non-precious functional catalysts has always been the milestone and still contributing significantly to exploring new advanced materials and moderating the cost of both complementary technologies. Metal-organic frameworks (MOFs) derived functional materials have found their way to the application as storage and conversion materials, owing to their structural variety, porous advantages, as well as the tunability and high reactivity. In this review, we provide a detailed overview of the latest progress of MOF-based materials operating in metal-air batteries and photovoltaic cells.

The characterization of thin-film solar cells is of huge importance for obtaining high open-circuit voltage and low recombination rates from the interfaces or within the bulk of the main materials. Among the many electrical characterization techniques, the two- and four-wire probe using the Cascade instrument is of interest since the resistance of the wires, and the electrical contacts can be excluded by the additional two wires in 4-wire probe configuration. In this paper, both two and four-point probes configuration are employed to characterize the CIGS chalcogenide thin-film solar cells. The two-wire probe has been used to measure the current-voltage characteristics of the cell which results in a huge internal resistance. Therefore, the four-wire connection is also used to eliminate the lead resistance to enhance the characterization’s accuracy. The load resistance in the two-wire probe diminishes the photogenerated current density at smaller voltage ranges. In contrast, the proposed four-wire probe collects more current at higher voltages due to enhanced carrier collection efficiency from contact electrodes. The current conduction mechanism is also identified at every voltage region represented by the value of the ideality factor of that voltage region. It is observed that a long time given to the charge collection results in increased current density at a higher voltage. According to the results and device characteristics, a novel double-diode model is suggested to extract the saturation current density, shunt and series resistances and the ideality factor of the cells. These cells are shown to be efficient in terms of low recombination at the interfaces and with lower series resistance as the quality of the materials is in its most possible conductive form. The measured internal resistance and saturation current density and ideality factor of the two measurement configuration is measured and compared.

The dynamic evolution and variation of electrical loads is now a priority for optimum management and, above all, forecasting. Indeed, these dynamic load variations require computer tools able to implement optimal load forecasting models. Scientific research into automated models for forecasting electrical loads therefore represents a challenge for scientific researchers. Several research studies have therefore been carried out. These include machine learning approaches such as: LSTM (Long Short-Term Memory), Support Vector Machine (SVM) and others. This article proposes a comparison study between a hybrid model based on the wavelet transform coupled with the adaboost method, and LSTM, for forecasting electricity consumption loads. Python 3.10 was used for the studies. The first results obtained consisted in the study of electricity load forecasts over four (04) data sets of the year (January, April, August and December). These results are very satisfactory, showing a good correlation between the real results of the electrical load consumption data, and the results of the implemented model. The electrical load consumption data are collected from a renewable energy production source: photovoltaic solar energy. The model test results (R2) obtained range from 0.919 to 0.958. These results are representative of real data and reflect the model's performance. The second set of results concerns a comparative study between the methods used by Y. Xie et al (CNN, MLP, LSTM-AM and LSTM-AM-MLP), and our approach. The prediction results obtained between the approaches show a prediction gap ranging from 0.15 to 0.78 for RMSE and 0.83 for MAPE. These results show significant differences between the methods. The minimization of errors by our model, therefore, reflects the model's performance in terms of accuracy, which is necessary for the optimal management of consumer electricity load forecasts in order to ensure balance between supply and demand.

Nanomaterials have shown significant promise for enhancing the performance of composite materials and increasing their functionality for various industrial applications. This review explores the unique properties of nanomaterials, particularly carbon-based nanomaterials, and provides key findings in utilizing them to enhance composite performance. It highlights specific nano-based composite materials and their significant potential in advancing the field of nanocomposites. Challenges associated with nanocomposite production and utilization are also discussed, along with possible solutions to address them. Finally, the study provides recommendations for continued research and innovation in nanocomposites to fully unlock the benefits of these advanced materials for broader future applications.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

There is a global demand for alternative energy sources away from unsustainable fossil fuels. COP26 agreed that fossil fuels should be phased down; at COP27, anxiety about the cost and availability of energy was raised, and COP28 reiterated the phasedown of coal power. Solar technology in the form of Perovskite solar cells is one such alternative energy source. This article considers the fabrication of the Perovskite layer in a solar cell and postulates the extent to which Material Flow Cost Accounting (MFCA) could be used as a feasible costing method, among other things, to address byproduct and waste generation. Through MFCA, the monetary and physical flows of materials are identified and can be applied throughout the supply chain to facilitate affordability, from the extraction of the ore, transportation, fabrication of the chemicals, manufacturing and distribution of the solar cell and panels, and finally, the recycling of the panel. Informed by these observations, a conceptual framework for applying MFCA in fabricating the Perovskite layer in the supply chain is developed based on sets of qualitative propositions. Future work will be researching the processes of manufacturing solar cells, costing raw materials, energy flows, and solar cell manufacturing emissions.

In this research work, we describe the preparation process, characterization, and photo-physical studies of an ionic liquid (IL) based semiconductor Zinc Oxide (ZnO) nanoparticles synthesized by an economical wet chemical precipitation method. For the first time, an IL was synthesized with the help of a chemical reaction between triethylamine (TEA) and bromoacetic acid (BAA). A polyamide dye was prepared by a reaction between two monomers, ethylenediamine (EDA) and trimesoylchloride (TMC), under room temperature conditions. The polyamide dye was capped on ZnO nanoparticles, and the final product was divided into three different samples, A, B, and C, according to level of concentrations of IL and Polyamide dye. These samples were characterized with X-Ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Dynamic Light Scattering (DLS) spectra, Ultraviolet-Visible (UV-Vis), and Fluorescence spectroscopies. The formation of polyamide linkages in the ionic liquid has been confirmed by a spectroscopic method using Fourier Transform Infrared (FTIR) spectroscopy. The capping of polyamide dye molecules on the surface of ZnO nanoparticles revealed two things: (i) improved UV absorption spectra and (ii) enhanced luminescence in the photoluminescence spectra. Hence, during investigations, broad absorption bands were observed at peaks 263 nm, 278 nm, and 276 nm respectively for samples A, B, and C. Further, IL was used as an electrolyte or redox mediator and polyamide as a dye material in the fabrication of ZnO Dye-Sensitized Solar Cells (DSSCs). The samples A, B, and C were used in the fabrication of photo-anode assemblies for ZnO DSSCs. The ZnO DSSCs were tested under strong simulated light at Air Mass (AM) 1.5 solar irradiations. The observed photovoltaic results shown that solar cell SCB generated a maximum power conversion efficiency (η) of 5.65%, higher than the power conversion efficiencies of solar cells SCA (3.99%) and SCC (4.46%) respectively. The Incident Photon to Current Conversion Efficiency (IPCE) spectra values of ZnO DSSCs shown a significant improvement in the incident photon to current conversion efficiency of solar cell SCB (IPCE=61%) as compared to SCC (enhanced by 6%) and SCA (enhanced by 4%). Such solar cell assemblies can be suitable for green and clean energy applications.

In this paper, the overall performance of Cu-(In,Ga)-Se₂ (CIGSe) solar cells was improved in the ultraviolet (UV)–visible wavelength region by two-segment process. In which, adjusting DC sputtering powers (20–40 W) for absorbers (segment I), and metal-alloy compositions (CdS, ZnO/CdS, ZnMgO/CdS and ZnMgO) for buffers (segment II) were explored and characterized. Upon choosing the optimal-30-W CIGSe-absorber (with 0.95-CGI ratio) sputtered by the segment-I process, the Cu-rich film can distinctly boost grain growth, thus reducing the trap state density. After segment-II process as the toxic-CdS alternative, the optimal Zn_0.9Mg_0.1O-alloy buffer can reach the best conversion efficiency (η = 8.70%) was attained for the environmental protection. Meanwhile, and the overall internal/external quantum efficiencies (IQE/EQE) were improved by 13.15%, respectively for the 2.48–3.62-eV bandgap (short wavelength) range. The developed photovoltaic (PV) module (with 9 optimum-CIGSe cells) exhibits acceptable stability with a variance within ±5% over the 60-day experiment. This discovery in PV-device research contributes to a new scientific understanding of renewable energy. Furthermore, this study undeniably enhances the progress of practical applications for PV-modules in alignment with sustainable development goals. It also actively supports the development of eco-friendly communities.

Due to increased energy intensive human activities resulting accelerated demand for electric power coupled with occurrence of natural disasters with increased frequency, intensity, and duration, it becomes essential to explore and advance renewable energy technology for sustainability of the society. Addressing the stated problem and providing a radical solution has been attempted in this study. To harvest the renewable energy, among variety of solar cells reported, a composite a-Si/CZTS photovoltaic devices has not yet been investigated. The calculated parameters for solar cell based on the new array of layers consisting of a-Si/CZTS are reported in this study. The variation of i) solar cell efficiency as a function of CZTS layer thickness, temperature, acceptor, and donor defect concentration; ii) variation of the open circuit current density as a function of temperature, open circuit voltage; iii) variation of open circuit voltage as a function of the thickness of the CZTS layer has been determined. There has been no reported study on a-Si/CZTS configuration-based solar cell, analysis of the parameters, and study to address the challenges imped efficiency of the photovoltaic device and the same has been discussed in this work. The value of the SnO2/a-Si/CZTS solar cells obtained from the simulation is 23.9 %.

Surface passivation, which has been intensively studied recently, is essential for the perovskite solar cells (PSCs), due to the intrinsic defects in perovskite crystal. A series of chemical or physical methods have been published for passivating the defects of perovskite, which effectively suppressed the charge recombination and enhanced the photovoltaic performance. In this study, the n-type semiconductor of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) is dissolved in chlorobenzene (CB) for the surface passivation during the spin-coating process for depositing the two-dimensional (2D) perovskite film. This approach simplifies the fabrication process of 2D PSCs and benefits the film quality. As a result, the defects of perovskite film are effectively passivated by this method. A better perovskite/PCBM heterojunction is generated, exhibiting an increased film coverage and improved film morphology of PCBM. It is found that this technology results in an improved electron transporting performance as well as suppressed charge recombination for electron transport layer. As a result, PSCs based on the one-step formed perovskite/PCBM heterojunctions exhibit the optimized power conversion efficiency of 15.69% which is about 37% higher than that of regular perovskite devices. The device environmental stability is also enhanced due to the quality-improved electron transport layer.

Two gallium porphyrins, a tetraphenyl GaCl porphyrin, termed as (TPP)GaCl, and an octaethylporphyrin GaCl porphyrin, termed as (OEP)GaCl were synthesized to use as electron cascade in ternary organic bulk heterojunction films. A perfect matching of both gallium porphyrins energy levels with that of poly(3-hexylthiophene-2,5-diyl) (P3HT) or poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) polymer donor and the 6,6-phenyl C71 butyric acid methyl ester (PCBM) fullerene acceptor forming an efficient cascade system that could facilitate electron transfer between donor and acceptor was demonstrated. Therefore, ternary organic solar cells (OSCs) using the two porphyrins in various concentration were fabricated, where a performance enhancement was obtained. In particular, (TPP)GaCl-based ternary OSCs of low concentration (1:0.05 vv%) exhibited a ~17 % increase of the power conversion efficiency (PCE) compared with the binary device due to improved exciton dissociation, electron transport and reduced recombination. On the other hand, ternary OSCs with the (TPP)GaCl of high concentration (1:0.1 vv%) and (OEP)GaCl (1:0.05 and 1:0.1 vv%) showed poorest efficiencies due to very rough nanomorphology and suppressed crystallinity of ternary films when the GaCl porphyrin introduced in the blend, as revealed from X-ray diffraction (XRD) and atomic force microscopy (AFM). The best performed devices exhibited also improved photostability, when exposed to sunlight illumination for a period of 8 h than the binary OSCs, attributed to the suppressed photodegradation of the ternary (TPP)GaCl 1:0.05-based photoactive film.

The susceptible-infected-recovered-vaccinated-deceased (SIRVD) epidemic compartment model extends the SIR model to include the effects of vaccination campaigns and time-dependent fatality rates on epidemic outbreaks. It encompasses the SIR, SIRV, SIRD, and SI models as special cases, with individual time-dependent rates governing transitions between different fractions. We investigate a special class of exact solutions and accurate analytical approximations for the SIRVD and SIRD compartment models. While the SIRVD and SIRD equations pose complex integro-differential equations for the rate of new infections and the fractions as a function of time, a simpler approach considers determining equations for the sum of ratios for given variations. This approach enables us to derive fully exact analytical solutions for the SIRVD and SIRD models. For nonlinear models with a high-dimensional parameter space, such as the SIRVD and SIRD models, analytical solutions, exact or accurately approximative, are of high importance and interest: not only as suitable benchmarks for numerical codes, but especially as they allow us to understand the critical behavior of epidemic outbursts as well as the decisive role of certain parameters. In the second part of our study, we apply a recently developed analytical approximation for the SIR and SIRV models to the more general SIRVD model. This approximation offers accurate analytical expressions for epidemic quantities, such as the rate of new infections and the fraction of infected persons, particularly when the cumulative fraction of infections is small. The distinction between recovered and deceased individuals in the SIRVD model affects the calculation of the death rate, which is proportional to the infected fraction in the SIRVD/SIRD cases but often proportional to the rate of new infections in many SIR models using a posteriori approach. We demonstrate that the temporal dependence of the infected fraction and the rate of new infections differs when considering the effects of vaccinations and when the real-time dependence of fatality and recovery rates diverge. These differences are highlighted for stationary ratios and gradually decreasing fatality rates. \Revised{The case of stationary ratios allows one to construct a new powerful diagnostics method to extract analytically all SIRVD model parameters from measured COVID-19 data of a completed pandemic wave.

The leather industry is one of the most polluting industries in the world due to the large amounts of waste following the raw hides processing, but also due to the high content of chemicals present in their composition. The main problem of chromium-tanned leather solid waste is related to their storage, because of the ability of chromium to leach in soil or water, and also owing to the high ability of trivalent chromium to oxidize to its toxic form, hexavalent chromium. The purpose of this study is to present the latest methods for extracting trivalent chromium from the composition of solid leather wastes. The extraction methods identified in the present study are based on acid/basic/enzymatic hydrolysis and substitution with the help of organic chelators (organic acids and organic acid salts). In addition, the study includes a comparative analysis between the advantages and disadvantages of each identified extraction method. At the same time, the study also presentes alternative chromium extraction methods based on the combination of conventional extraction methods and ultrasound-assisted extraction.

In this work, we compiled our research on lanthanide-based luminescent materials, prepared down-shifter layers, and studied their effect on photovoltaic (PV) mini-modules. The compounds we have prepared (C1-C17), with formulas [Eu2(phen)2(bz)6] (C1), [Eu2(bphen)2(bz)6] (C2), [Eu(tta)3bphen] (C3), [Eu(bta)3pyz-phen] (C4), [Eu(tta)3pyz-phen] (C5), [Eu(bta)3me-phen] (C6), [Er(bta)3me-phen] (C7), [Yb(bta)3me-phen] (C8), [Gd(bta)3me-phen] (C9), [Yb(bta)3pyz-phen] (C10), [Er(tta)3pyz-phen] (C11), [Eu2(bz)4(tta)2(phen)2] (C12), [Gd2(bz)4(tta)2(phen)2] (C13), [EuTb(bz)4(tta)2(phen)2] (C14), [EuGd(bz)4(tta)2(phen)2] (C15), [Eu1.2Gd0.8(bz)4(tta)2(phen)2] (C16) and [Eu1.6Gd0.4(bz)4(tta)2(phen)2] (C17), can be grouped into three families based on their composition: Series C1–6 were synthesized using Eu3+ ions and phenanthroline derivatives as the neutral ligands, and fluorinated β-diketonates as the anionic ligands. Complexes C7–11 were prepared with ligands similar to those of compounds C1–6 but were synthesized with Er3+, Yb3+, or Gd3+ ions. Series C12–17 exhibit the general formula [M1M2(bz)4(tta)2(phen)2], where M1 and M2 can be Eu3+, Gd3+, or Tb3+ ions, and the ligands are benzoate (bz–), 2-thenoyltrifluoroacetone (tta–) and 1,10–phenanthroline (phen). All compounds were characterized using X-ray techniques, and their photoluminescent properties were studied. We then examined their impact on the EQE (External Quantum Efficiency) of PV mini-modules and their durability in a climate chamber when embedded in PMMA and EVA films. This review emphasizes the methodology employed and the key findings, including enhanced mini-module efficiency. Additionally, we present promising results on the application of compound C6 in a bifacial solar cell.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

In the past decade, considerable efforts have been devoted to the development of semitransparent organic solar cells. Numerous materials and architectures have been proposed for the future commercialization of these devices. Among these, the use of ternary active layers demonstrated a great promise for the development of efficient semi-transparent organic solar cells with the potential for future applications including self-powered greenhouses and powered windows. Researchers seek alternative solutions to the trade-off between device power conversion efficiency (PCE) and average visible transmittance (AVT), with photoactive materials being the key parameters that govern both (PCE) and (AVT) as well as device stability. Several new organic materials, including polymers and small molecules, were synthesized, and used in conjunction with a variety of techniques to achieve semitransparent conditions. In this review paper, we will look at the working principle and key parameters of semi-transparent organic solar cells, as well as the methods that have been used to improve the performance of ternary-based semi-transparent organic solar cells. The main approaches were concluded to be spectral enhancement and transparency increment of the active layer through bandgap tuning, utilizing novel organic semiconductors, and design architecture of the active layers.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

This study was conducted to recover valuable metals (silicon and silver) using acid leaching and substitution reactions with copper powder from the pulverized solar cell separated from the PV ribbon. Leaching experiments were conducted according to nitric acid concentration by molar solution as 1M, 2M, and 3M using an ultrasonic cleaner at a reaction temperature of 60 °C for the leaching times of 30 to 120 minutes. Si phases were detected at all leaching reaction times, it was confirmed that the aluminium was removed effectively if the nitric acid leaching time was more than 30 minutes, and silicon with a purity above 99% could be recovered. The silver was precipitated by adding copper, which has greater reducibility than Cu, Al, Si, Pb, and Sn. When the addition of copper powder was 0.75 and 1.0 g, precipitate was produced 0.23 and 0.55 g, respectively. The optimal condition for the recovery of silver by the addition of copper powder was 1 g, where is recovery rate reached 93.3%.

This paper presents the novel development of a shape memory polymer foam based on polymer-polymer nanocomposites. Herein, polylactide (PLA)/biosourced polyamide (PA) foams are fabricated by in-situ fibrillation of polymer blends and subsequent supercritical CO2 foaming technique. In this system, PLA serves as a shape memory polymer to endow this foam with a shape memory effect (SME), and in-situ generated PA nanofibers are employed to reinforce the PLA cell walls and provide an additional permanent phase. Concentration of PA, 5 wt.%, is chosen to form an entangled nanofibrillar network. Foams of PLA/PA nanoblends with the same content of constituents are fabricated to reveal the effect of minor phase morphology on the cell structure and shape memory behavior of polymer foams. Profiting from the reinforcing effect of PA nanofibers, the PLA/PA nanocomposite foam exhibits smaller foam cells, a narrower cell size distribution and a comparable cell concentration than the PLA/PA nanoblend foam. In addition, PA nanofibers, unlike PA nanodroplets, favor the shape fixation ratio and recovery ratio and shorten the shape recovery time.

The purpose of this disquisition is to analyze bullfighting, its advances and setbacks at a global and local level in terms of animal law. It was developed as a descriptive documentary research with a non-experimental design, using the observation and interpretation of documents related to the subject, from the global level, to the local, the national, specific to the regions and communities, being interpreted through the hermeneutic method. In the analysis, results were reached such as: every day more countries are willing to assume that bulls, because they are living beings that feel, are being attended to from the legal and the ethical, propitiating changes in the way of thinking of people in terms of wanting to consider bullfighting, a sport, art and hobby considered cultural heritage of many countries. For this reason, different actions have been generated from surveys, to define the acceptance or not of these events. It is concluded that there are important advances in this regard, as bullfighting is being prohibited in different parts of the world, taking into account the protection that protects animals, but the laws do not establish specific prohibition in this regard worldwide.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

The optimized design of catalyst layer (CL) plays a vital role to improve the performance of polymer electrolyte membrane fuel cells (PEMFCs). The need to improve transport and catalyst activity is especially important at low Pt loading, where local oxygen and ionic transport resistances decrease the performance due to an inevitable reduction of active catalyst sites. In this work, local oxygen and ionic transport are analyzed using direct numerical simulation on virtually reconstructed microstructures. Four morphologies are examined: (i) heterogeneous, (ii) uniform, (iii) uniform vertically-aligned, and (iv) meso-porous ionomer distributions. The results show that the local oxygen transport resistance can be significantly reduced, while maintaining good ionic conductivity, through the design of high porosity CLs (ε≃0.6−0.7) with low agglomerated ionomer morphologies. Ionomer coalescence into thick films can be effectively mitigated by increasing the uniformity of thin films and reducing the tortuosity of ionomer distribution (e.g., good ionomer interconnection in supports with a vertical arrangement). The local oxygen resistance can be further decreased by the use of blended ionomers with enhanced oxygen permeability and meso-porous ionomers with oxygen transport routes in both water and ionomer. In summary, achieving high performance at low Pt loading in next-generation CLs must be accomplished through a combination of high porosity, uniform and low tortuosity ionomer distribution, and oxygen transport through activated water.

The assessment of photovoltaic devices, which convert light energy into electricity, becomes significantly relevant due to the aspiration to reduce pollution on a global scale. In this context, the pursuit of optimizing the efficiency in converting light energy into electrical energy involves exhaustive studies and structural analyses of solar cells, all directed toward achieving this goal. This study introduces a research proposal aimed at analyzing the losses associated with series resistance (Rs). The analysis takes into account each component comprising this resistance, pro-posing a network of resistances that precisely models each of these elements. The aforementioned research focused on simple-structured crystalline silicon cells. During this investigation, the junction depth (xj) of n-p materials was varied with the aim of achieving efficiencies in the range of 12%. However, in the pursuit of this desired efficiency, a significant impact on series resistance was observed when analyzing the I-V curves of the cells obtained in each manufacturing process.

The feasibility of replacing the toxic chlorobenzene antisolvent with the environmentally friendly anisole in the fabrication of planar triple cation perovskite solar cells was explored. The successful integration of anisole not only ensures comparable device performance but also contributes to the development of more sustainable and green fabrication processes for next-generation photovoltaic technologies. Nevertheless, to ensure the possibility to achieve well-functioning unencapsulated devices, at any time of the year, with changed temperature and relative humidity, several batches with different cesium concentration were realized. We found that 10% of CsI in the precursor solution makes devices with low hysteresis index and sustained performance stability over a 90-day period both with cholorobenzene and anisole antisolvent. However the use of anisole as a green antisolvent ensures enhanced performance.

Suppressing the charge recombination at the interface of photoanode/electrolyte is the crucial way to enhance the photovoltaic performance of quantum dot sensitized solar cells (QDSSCs). In this scenario, ZnS/SiO2 blocking layer was deposited on TiO2/CuInS2 QDs to inhibit the charge recombination at photoanode/electrolyte interface. As a result, the TiO2/CuInS2/ZnS/SiO2 based QDSSCs delivers a power conversion efficiency (η) value of 4.63%, which is significantly higher than the 2.15% and 3.23% observed for QDSSCs with a TiO2/CuInS2 device and TiO2/CuInS2/ZnS, respectively. Electrochemical impedance spectroscopy and open circuit voltage decay analyses indicate that ZnS/SiO2 passivation layer on TiO2/CuInS2 suppress the charge recombination at the photoanode/electrolyte interface and prolongs the electron lifetime.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

Umbilical cord-derived mesenchymal stem cells (UC-MSCs) are reported to have features intermediate between fetal and adult mesenchymal cells. Hence, UC-MSCs were cocultured with chondrocytes and Schwann cells to induce differentiation because of their flexible differentiation potential. US-MSCs were obtained from umbilical cords and cells at second passage were used in the experiments. Atelocollagen sponge was used as the scaffold for coculture; a horizontal, interactive coculture plate with a 0.6-μm pore size filter was placed between the connected vessels. US-MSCs were cocultured separately with chondrocytes and Schwann cells and culture alone served as a control. Five weeks after induction of differentiation, each specimen was evaluated histologically. In specimens cocultured with chondrocytes and the controls, cartilage tissues were detected using hematoxylin-eosin and toluidine blue staining. Cells positive for S100 protein were detected in the specimens cocultured with Schwann cells, but not in the controls. UC-MSCs were easily induced to differentiate into chondrocytes and neural cells by coculture. This indicates that continuously-shared humoral factors were effective in inducing differentiation of UC-MSCs. Coculture appears to be a potential technique for tissue regeneration using MSCs.

In this study, 3-trimethoxy-silylpropane-1-thiol (MPTMS) was used as a surface modifier for Al2O3 powder to systematically analyze the effects of MPTMS concentration on the rheological properties, photocuring characteristics, and 3D printing performance of photocurable composite slurries. MPTMS concentration significantly influenced the rheological behavior of the slurry. Slurries containing 2 wt.% and 5 wt.% MPTMS exhibited a wide linear viscoelastic range (LVR). However, at concentrations of 10 wt.% and 20 wt.%, the LVR range narrowed, which led to reduced dispersion stability. In dispersion stability tests, the slurry with 2 wt.% MPTMS showed the most stable dispersion, while the 5 wt.% MPTMS concentration exhibited the highest photocuring rate. In 3D printing experiments, the 5 wt.% MPTMS concentration resulted in the most stable printed structures, whereas printing failures occurred with the 2 wt.% concentration. At 10 wt.% and 20 wt.%, internal cracking was observed, leading to structural defects. In conclusion, MPTMS forms silane bonds on the Al2O3 surface, significantly impacting the stability, rheological properties, and printing quality of Al2O3-acrylate composite slurries. An MPTMS concentration of 5 wt.% was found to be optimal, contributing to the formation of stable and robust structures.

We present an analysis of high-resolution, near-infrared (NIR) spectra relative to the solar transit of Venus of 5-6 June 2012, as observed with the Facility Infrared Spectropolarimeter (FIRS) at the Dunn Solar Telescope in New Mexico. These observations offer the unique opportunity to probe the upper layers (between ∼84 and 150 km in altitude) of a thick, CO2-dominated atmosphere with the transmission spectroscopy technique – a proxy for future studies of highly-irradiated atmospheres of Earth-sized exoplanets. We were able to visually identify absorption lines from the two most abundant CO2 isotopologues, and from the main isotopologue of CO in the retrieved spectrum of Venus. Furthermore, we perform a cross-correlation analysis of the transmission spectrum using transmission templates generated with petitRADTRANS. With the cross-correlation technique, it was possible to confirm detections of both CO2 isotopologues and CO. Additionally, we retrieve a cross-correlation signal for O3 on Venus. We demonstrate the feasibility of high-resolution, ground-based observations to study the chemical inventory of planetary atmospheres, employing techniques commonly used in exoplanet characterization.

The Sun is a huge gaseous body. However, we cannot observe events in the inner Sun due to the convection zone opacity according to previous models. Therefore, the flares originate from the front surface of the Sun. But the current study relied on the distance distribution of X-Ray solar flares, which concluded that the inner layers have much lower opacity than expected. It is even less than what was expected by the latest models based on helioseismology. This means that the flares may originate from the solar interior or solar core, and perhaps from the backside surface, and even appear to us from the frontside surface. Which the re-estimate and correct the currently listed solar flare’s location is needed. Additionally, the flare’s distance illustrations the solar interior layers and appears their boundaries from the core to the photosphere. This method allows us to monitor the variation of the core’s radius with time. The model of the flare’s distance has been developed in current study. But this needs to redevelopment after re-estimating the solar flares locations.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

A flat-plate unglazed solar water heater (SWH) with polymer thermal absorber was developed and tested. Polymer thermal absorber as a viable alternative to metal thermal absorber that is found in most SWH systems. The performance of this polymer SWH system is measured based on inlet and outlet water temperature, water flowrate, ambient air temperature and solar irradiance. The polymer thermal absorbers are hollow Polyvinyl Chloride (PVC) pipes with 20mm external diameter and 3 mm thick, painted in black to enhance radiation absorption. The pipes are arranged in a rectangular spiral inward-outward opposing-flow (RSioof). The collector pipes are placed in a 1 m2 square enclosure with bottom insulation and reflective surface for better radiation capture. Water circulation is a closed loop with a 16-liter uninsulated storage tank, driven by a pump and controlled by valves to maintain a mass flow rate of 0.00031 to 0.00034 kg/s. The test was conducted under partially clouded sky from 9 am to 5 pm, with solar irradiance between 105 and 1003 W/m2 and 27-36oC ambient air temperature. The SHW produced outlet hot water at 65oC by mid-day and maintained the storage temperature at 63oC until the end of test duration. Photo-thermal energy conversion was recorded with 23% maximum value. Results indicate that a flat plate solar water heater with polymer thermal absorber in RSioof design can be an effective alternative to the metal thermal absorber solar water heater and can be further optimized with glazing and tube sizing.

In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

Novel bio-inspired materials have gained recently great attention, especially in medical applications. Applying sophisticated design and engineering methods, various polymer-polymer hybrid systems with outstanding performance have been developed in last decades. Hybrid systems composed of bioelastomers and hydrogels are very attractive due to their high biocompatibility and elastic nature for advanced biomaterials used in various medical applications such as drug delivery systems and scaffolds for tissue engineering. Herein, we describe the advances in current state-of-the-art design, properties and applications of polymer-polymer hybrid systems in medical applications. Bio-inspired functionalities, including bioadhesiveness, injectability, antibacterial properties and degradability applicable to advanced drug delivery systems and medical devices will be discussed in a context of future efforts towards development of bioinspired materials.

A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

Solar flares are broadly classified as impulsive or gradual. Ions accelerated in a gradual flare are thought to be accelerated through a shock acceleration mechanism, but the particle acceleration process in an impulsive flare is still largely unexplored. To understand the acceleration process, it is necessary to measure the high-energy gamma-rays and neutrons produced by the impulsive flare. Under such circumstances, on November 7, 2004, a huge X2.0 flare occurred on the solar surface, where ions were accelerated to energies greater than 10 GeV. The accelerated primary protons collided with the solar atmosphere and produced line gamma-rays and neutrons. These particles were received as neutrons and line gamma-rays, respectively. Neutrons of a few GeV, on the other hand, decay to produce secondary protons while traveling 0.06 au in the solar-terrestrial space. These secondary protons arrived at the magnetopause. Although the flux of secondary protons is very low, the effect of collecting secondary protons arriving in a wide region of the magnetosphere (the Funnel or Horn effect) has resulted in significant signals being received by the solar neutron telescope at Mt. Sierra Negra (4,600 m). This information suggests that ions on the solar surface are accelerated to over 10 GeV with an impulsive flare.

Nanostructured polymer dispersed liquid crystals (nano-PDLCs) are transparent and optically isotropic materials, in which submicron-sized liquid crystal (LC) domains are dispersed within a polymer matrix. Nano-PDLCs can induce their birefringence by applying an electric field (E-field) based on reorientation of LC molecules. If nano-PDLCs are utilized as light scattering-less birefringence memory materials, it is necessary to suppress the relaxation of LC molecules orientation after removal of the E-field. We focused on a ferroelectric smectic A (SmA) to suppress the relaxation of LC molecules due to their layered structure and high viscosity. Although nano-PDLCs require a strong E-field to reorient LC molecules due to the anchoring effect on the LC/polymer interface, the required field strength can be reduced by using a ferroelectric smectic A (SmAF) LC with a large dielectric constant. In this study, we fabricated a nano-PDLC by irradiating an ultraviolet light to a mixture comprising of a SmAF LC, photocurable monomers and a photo-initiator and its electro-birefringence effect was evaluated using a polarizing optical microscopy. After removal of an E-field, enhanced memory effect was observed on the sample using SmAFLC comparing to nematic LC based nano-PDLCs. (193 words/ 200 words)