In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

A new two-dimensional nanomaterial – Titanium Carbide MXene (Ti₃C₂-MXene) – was reported in 2011. In this work, the microscale models of Ti₃C₂-MXene nanomaterial are considered with polymer matrix. The nanocomposites are modeled using nacre-mimetic brick-and-mortar assembly configurations due to enhanced mechanical properties and interlocking mechanism between the Ti₃C₂-MXene (brick) and polymer matrices (mortar). The polymer matrix material (Epoxy-resin) is modeled with elastic and viscoelastic behavior (Kelvin-Voigt Model). The Finite Element Method is used for numerical analysis of the microscale models with the multi-point constraint method to include Ti₃C₂-MXene fillers in the polymer matrix. Ti₃C₂-MXenes are considered as thick plate elements with transverse shear effects. The response of elastic and viscoelastic models of polymer matrix are studied. Finally, a tensile and compressive load is applied at the microscale and the effective load transfer due to nacre-mimetic configuration is discussed. This paper provides nacre-mimetic models to pre-design the nanocomposite for optimal performance with damage resistance and enhanced strength.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

The present investigation highlights the synthesis of polyaniline (PANI) coated graphene oxide doped with SrTiO3 nanocube nanocomposites through facile in-situ oxidative polymerization method for the efficient removal of carcinogenic dyes, namely, the cationic dye methylene blue (MB) and the anionic dye methyl orange (MO). The synthesised nanocomposites were characterised by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adsorption efficiencies of graphene oxide (GO), PANI homopolymer and SrTiO3 nanocubes-doped nanocomposites were assessed by monitoring the adsorption of methylene blue and methyl orange dyes from aqueous solution. The adsorption efficiency of nanocomposites doped with SrTiO3 nanocubes were found to be of higher magnitude as compared with undoped nanocomposite. Moreover, the nanocomposite with 2 wt% SrTiO3 with respect to graphene oxide demonstrated excellent adsorption behaviour with 99% and 91% removal of MB and MO respectively, in a very short duration of time.

Modern medical needs call for the efficient remedies against bacterial diseases including severe pulmonary infections reported as a secondary SARS-Cov-2 infection. Here, we propose imprinted drug ciprofloxacin (CF) into the polymer based on methyl-β-cyclodextrin (MCD) via template synthesis. The obtained polycarbamide nanoparticles possess CF's sustained drug release. The interaction of human serum albumin (HSA) with CF and CF-MCD carriers was conducted by FRET, FTIR, fluorescence, and circular dichroism spectroscopy. These studies uncovered that MCD decreases CF's binding efficiency by 2 times, whereas CF’s encapsulation in polymer matrix doubles the Ka value. The changes in HSA’s secondary structure indicate no alterations in the main mechanism of complex formation between CF and HSA in the presence of MCD-based carries. The drug delivery system demonstrates prolonged CF release at pH 7.4 in presence of HSA (model conditions of blood plasma). CF-MCD carriers inhibit E. coli and B. subtilis growth, but for MAX systems we observed a MIC’s increase (~2 times). We believe that our findings are important for further development of new efficient drug forms.

The goal of this article is to provide a review of the experimental techniques and procedures using vibration methods for the Structural Health Monitoring (SHM) of Polymer-Matrix Composites (PMC). It aims to be a guide for any researchers to carry out vibration experiments. The linear methods are first introduced. But as PMC is a complex material, these classic methods showed some limits, such as low accuracy for small damages, and a high environmental dependency. This is why the nonlinear methods are secondly studied, considering that the complexity of PMC induces a nonlinear behavior of the structure after damage occurrence. The different damage mechanisms are well explained in order to evaluate the potential of each vibration method to detect them.

Due to satisfactory mechanical properties, low specific weight and other advantages, a substantial utilization of laminated structural composites in many components and equipments of several industry sectors, especially in the past two decades, has been made. This class of materials has a good potential to be an important ally to support scientists and engineers with the main current world challenge: an energy transition process that must occur with sustainability, eco-friendly materials and based on an efficient reduction of greenhouse gas emissions. In this context, a microanalysis (scale length: 10μm to 1mm) of mechanical behavior that considers the multiphase characteristics, at leastwise a matrix and a reinforcement phase, of this kind of composites must be explored, i. e., a heterogeneous material is assumed to predict, for example, the effective tensors of stiffness or compliance by a homogenization process, modeling to damage analyses, studies about progressive delamination and other specific aspects of a composite can be previously investigated using micromechanical approaches. Therefore, the understanding of fundamental micromechanics as well as some advanced models are essential to apply these materials in structural industry components. In this sense, this systematic literature review is designed to investigate the main basic and advanced models of laminated composites micromechanics and using this overall study, have been developed, in the end, an analysis of research trends to the topic, in which, lines to future researches are indicated.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

The susceptible-infected-recovered-vaccinated-deceased (SIRVD) epidemic compartment model extends the SIR model to include the effects of vaccination campaigns and time-dependent fatality rates on epidemic outbreaks. It encompasses the SIR, SIRV, SIRD, and SI models as special cases, with individual time-dependent rates governing transitions between different fractions. We investigate a special class of exact solutions and accurate analytical approximations for the SIRVD and SIRD compartment models. While the SIRVD and SIRD equations pose complex integro-differential equations for the rate of new infections and the fractions as a function of time, a simpler approach considers determining equations for the sum of ratios for given variations. This approach enables us to derive fully exact analytical solutions for the SIRVD and SIRD models. For nonlinear models with a high-dimensional parameter space, such as the SIRVD and SIRD models, analytical solutions, exact or accurately approximative, are of high importance and interest: not only as suitable benchmarks for numerical codes, but especially as they allow us to understand the critical behavior of epidemic outbursts as well as the decisive role of certain parameters. In the second part of our study, we apply a recently developed analytical approximation for the SIR and SIRV models to the more general SIRVD model. This approximation offers accurate analytical expressions for epidemic quantities, such as the rate of new infections and the fraction of infected persons, particularly when the cumulative fraction of infections is small. The distinction between recovered and deceased individuals in the SIRVD model affects the calculation of the death rate, which is proportional to the infected fraction in the SIRVD/SIRD cases but often proportional to the rate of new infections in many SIR models using a posteriori approach. We demonstrate that the temporal dependence of the infected fraction and the rate of new infections differs when considering the effects of vaccinations and when the real-time dependence of fatality and recovery rates diverge. These differences are highlighted for stationary ratios and gradually decreasing fatality rates. \Revised{The case of stationary ratios allows one to construct a new powerful diagnostics method to extract analytically all SIRVD model parameters from measured COVID-19 data of a completed pandemic wave.

In the last two decades, the application of composite structures in many industrial sectors has been made progressively. For the current major scientific and technological challenge, the energy transition with sustainable and eco-friendly initiatives, the polymer matrix laminated composites have been revealed as an excellent alternative for the renewable energy sector. In this context, the knowledge about mechanical behavior of multiphase materials is required. Then, researches related to macro, mesomechanical and multiscale approaches are very important to improve accuracy of the models to predict effective mechanical properties and to develop a better understanding about complex phenomena such as progressive damage, creep and fatigue. Due to theses needs, this research is a synthesis of fundamentals and advanced topics concerning to global modeling of laminated composite structures, layerwise analyzes and micro-macromechanical models, in which mainly fiber, matrix, interface and damage characteristics are studied and used in the macroscale approach. At the end of this study, some final remarks and a trend analysis are proposed based on literature consulted, in other words, expectations for the future works are made by the authors.

This paper considers the Hermitian solutions of a new system of commutative quaternion matrix equations, we establish both necessary and sufficient conditions for the existence of solutions. Furthermore, we derive an explicit general expression when it is solvable. To illustrate our main findings, we present two numerical algorithms and examples in this paper.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

The release of the active substance from the matrix modified-release tablets based on Kollidon®SR and chitosan depends on its solubility in the dissolution medium and on the composition of the matrix-forming polymers. The study is based on new oral matrix tablets based on Kollidon®SR and chitosan, formulated to optimize the low oral bioavailability of chlorzoxazone, a non-steroidal anti-inflammatory drug, a class II Biopharmaceutical Classification System. Nine types of chlorzoxazone matrix tablets were obtained using the direct compression method, and their combination at 1:1, 1:2, 1:3 chlorzoxazone/ excipients, 20%-40% (w/w) Kollidon®SR, 3-7% (w/w) chitosan and the auxiliary substances were formulated in constant concentrations. Pharmaco-technical characterization included the analysis of flowability and compressibility properties (flow time, friction coefficient, angle of repose, Hausner ratio, Carr Index), and of pharmaco-chemical characteristics (mass and dose uniformity, thickness, diameter, mechanical strength, Friability, degree of softening, in vitro release profile) of the tablets. Based on the initial evaluation of the pharmaco-technical analysis, pharmaco-chemical characteristics, and in vitro release profile, only three matrix tablet formulations (F1b, F2b, and F3b) were further tested. They were evaluated through Fourier-transform infrared spectrometry, X-ray Diffraction, thermogravimetry, differential scanning calorimetry, and in vitro dissolution tests. The three formulations were comparatively studied regarding the release kinetics of active substances using in vitro release testing. The results were analyzed by fitting into four representative mathematical models for the modified release oral formulations. In vitro kinetic study reveals a complex mechanism of release occurring in the first (0 - 2 hours) and second (2.0 hours – 36 hours) steps of drug release. Two factors have been calculated to assess the release profile of chlorzoxazone: f1 - the similarity factor and f2 - the factor difference. The results have shown that both Kollidon®SR and chitosan may be used as matrix-forming agents when combined with chlorzoxazone. In vitro dissolution tests revealed the F2b sample, data suggesting a faster drug release. The three formulations showed optimum pharmaco-technical properties and in vitro kinetic study, and they had tremendous potential to be used in oral pharmaceutical products for the controlled delivery of chlorzoxazone.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

This note reconsiders a matrix equality $A_1A_2^{-}A_3A_4^{-}A_5 = A$ composed by six matrices of appropriate sizes, where $A_2^{-}$ and $A_4^{-}$ are generalized inverses of $A_2$ and $A_4$, respectively, and solves a selection of matrix set inclusion problems associated with various mixed reverse order laws for generalized inverses of products of two, three, and four matrices by means of this equality and its variations.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Thin people who undergo implant insertion into the chest wall face a high risk of implant exposure to the external environment. Five months after an 8-year-old boy underwent implantable cardioverter-defibrillator (ICD) implantation in a subcutaneous pocket in the left anterolateral chest wall to manage long QT syndrome, ICD replacement became necessary owing to exposure risk from distal and lateral thinning of the ICD pocket. Pocket rupture and exposure would increase the risk of infection; therefore, we performed ICD removal and primary pocket closure. Two weeks later, a new suprafascial pocket was created, acellular dermal matrix (ADM) was attached to the inner wall to prevent ICD protrusion, and a new ICD was inserted. One year postoperatively, the ADM was engrafted, and no complications were observed. A thin subcutaneous layer increases the risk of ICD implantation complications. Inner wall strengthening with ADM can help prevent pocket rupture.

In Indonesia, types of meat are still identified manually due to increasing prices for beef and buf-falo ahead of Idul Fitri. Traders mix beef with pork to thwart the beef scam. Haar wavelet and GLCM, GLCM with angles of 0°, 45°, 90°, and 135°, as well as matrices using contrast, correlation, energy, homogeneity, and entropy, are used in feature extraction. The following are the results of meat image classification testing using k-NN, Haar wavelet, and GLCM: The k-NN algorithm shows superiority in identifying fresh (99%), frozen (99%), and rotten (96%) meat texture images with the most fantastic accuracy results in every situation. Meanwhile, GLCM routinely provides good results, especially regarding the texture image of fresh meat (183.21) and rotten meat (115.79). However, despite delivering less throughput than k-NN and GLCM, Haar wavelets are still helpful, especially when dealing with fresh meat texture images (89,96).

Novel bio-inspired materials have gained recently great attention, especially in medical applications. Applying sophisticated design and engineering methods, various polymer-polymer hybrid systems with outstanding performance have been developed in last decades. Hybrid systems composed of bioelastomers and hydrogels are very attractive due to their high biocompatibility and elastic nature for advanced biomaterials used in various medical applications such as drug delivery systems and scaffolds for tissue engineering. Herein, we describe the advances in current state-of-the-art design, properties and applications of polymer-polymer hybrid systems in medical applications. Bio-inspired functionalities, including bioadhesiveness, injectability, antibacterial properties and degradability applicable to advanced drug delivery systems and medical devices will be discussed in a context of future efforts towards development of bioinspired materials.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Hydrogels prepared from natural polymer have attracted extensive attentions in biomedical fields such as drug delivery, wound healing, and regenerative medicine due to their good biocompatibility, degradability and flexibility. This review outlines the commonly used natural polymer in hydrogel preparation, including cellulose, chitosan, collagen/gelatin, alginate, hyaluronic acid and starch. The polymeric structure and process/synthesis of natural polymers are illustrated, and natural polymer-based hydrogels including the hydrogel formation and properties are elaborated. Subsequently, the biomedical application of hydrogels based on natural polymer in drug delivery, tissue regeneration, wound healing and other biomedical field is summarized. Finally, the future perspectives of natural polymers and hydrogels based on them are discussed. For natural polymer, novel technologies such as enzymatic and biological methods are developed to improve the structural properties and the development of new natural based polymers or natural polymer derivatives with high performance is still very important and challenging. For natural polymer-based hydrogels, novel hydrogel materials, like double-network hydrogel, multifunctional composite hydrogels and hydrogel microrobots are designed to meet the advanced requirements in biomedical application, and new strategies such as dual-crosslinking, microfluidic chip, micropatterning and 3D/4D bioprinting, have been explored to fabricate advanced hydrogel materials with designed properties for biomedical application. Overall, natural polymeric hydrogels have attracted increasing interests in biomedical application, and the development of novel natural polymer-based materials and new strategies/methods for hydrogel fabrication is badly desirable and still challenging.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p<0.05; p<0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p<0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

Due to the growing interest in biopolymers, biosynthesizable and biodegradable polymers currently occupy a special place. Unfortunately, the properties of native biopolymers are not satisfactory, which explain that attempts are being made to modify them. The work attempts to improve the properties of poly(3-hydroxybutyrate) (P3HB) using linear aliphatic polyurethane (PU) based on 1,4-butanediol and hexamethylene 1,6-diisocyanate. The conducted studies on the effect of the amount of PU used (5, 10, 15 and 20 wt.%) showed an improvement in the thermal properties of the prepared polymer blends. There was an increase in the degradation temperature of the ob-tained blends in relation to the native P3HB by 12-57C, and the difference between the melting point and the degradation point was above 100°C for most of the obtained blends. As part of the tested mechanical properties of the new polymer blends, we noted the desired increase in the tensile strength, in the relative elongation at break and in the impact strength with a decrease in hardness, in particular with the presence of 5 wt.% PU. Therefore, for further improvement, hybrid nanobiocomposites with 5 wt.% PU and organically modified montmorillonite (MMT – Cloisite 30B) were produced. The nanoadditive was used in typical amount of 1-3 wt.%. The nanostructure of the biocomposites produced by extrusion was examined by small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM), the morphology by scanning electron microscopy (SEM), and compatibility by infrared spectroscopy (FT IR). In addition, selected mechanical properties were determined and thermal properties were tested by the thermogravimetric analysis (TGA) and the standard differential scanning calorimetry (DSC). The polyester and polyurethane chains penetrated into the interlayer spaces of organically modi-fied nanoclay – Cloisite30B and the complete delamination occurred during direct mixing in the extrusion process. FT IR spectral analysis showed the compatibility of the polymer biocomposite components by the coexistence of intermolecular interactions in the form of hydrogen bonds. The morphology studies of the produced hybrid nanobiocomposites showed an interaction of the bi-opolymer matrix with PU and Cloisite30B and the formation of easily migrating polyester-polyurethane-montmorillonite adducts, which resulted in improved mechanical properties com-pared to the properties of the native P3HB and P3HB-PU compositions. The influence of the presence of a nanofiller on the properties of the prepared nanobiocomposites was tested and it was found that, as expected, the smallest amount of nanofiller provides the best results.It was found that the obtained nanobiocomposites containing the smallest amount of nano-fillers, i.e. 1 wt.% Cloisite30B exhibited the best mechanical and thermal properties. The desired decrease in hardness by 15% and a higher value of impact strength by 15%, an increase in elonga-tion at break by 60% and an increase in thermal stability of the newly produced biocomposites compared to to the native P3HB were observed. The prepared nanobiocomposites combined the best features caused by the elasticizing effect of polyurethane and the formation of P3HB-PU-MMT adducts.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

The transformation of the states of polarization of electromagnetic waves that interact with polarimetrically linear media can be represented by means of the associated Mueller matrix. A global measure of the ability of a linear medium to modify the states of polarization of incident waves, due to any combination of enpolarizing, depolarizing and retarding properties, is introduced as a distance of the Mueller matrix to the identity matrix. This new descriptor, called the polarizing power, is applicable to any Mueller matrix and can be expressed as a function of the degree of polarimetric purity and the trace of the Mueller matrix. The graphical representation of the feasible values of the polarizing power provides a general view of its main peculiarities and features. The values of the polarizing power for several typical devices are analyzed.

In this paper after introducing a model of binary data matrix (BDM) for physical parameters of an evolving system (of particles), we develop a Hilbert space as an ambient space to derive induced metric tensor on embedded parametric manifold identified by associated joint probabilities of particles observables (parameters). Parameter manifold assumed as space-like hypersurface evolving along time axis, an approach that resembles 3+1 formalism of ADM and numerical relativity. We show the relation of endowed metric with related density matrix. Identification of system density matrix by this metric tensor, leads to the equivalence of quantum Liouville equation and metric compatibility condition while covariant derivative of metric tensor has been calculated respect to Wick rotated time or spatial coordinates. After deriving a formula for expected energy per particles, we prove the equality of this expected energy with local scalar curvature of related manifold. We show the compatibility of BDM model with Hamilton-Jacobi formalism and canonical forms. On the basis of the model, I derive the Ricci flow like dynamics as the governing dynamics and subsequently derive the action of BDM model and Einstein field equations. Given examples clarify the compatibility of the results with well-known principles such as equipartition energy principle and Landauer’s principle. This model provides a background for geometrization of quantum mechanics compatible with curved manifolds and information geometry. Finally, we conclude a “bit density principle” which predicts the Planck equation, De Broglie wave particle relation, , Beckenstein bound and Bremermann limit.

The present paper discusses a study of a class of Charlier matrix polynomials and its generalized analogue. Certain generating matrix functions, recurrence matrix relations, matrix differential equation, summation formulas and many new results have been discussed for these matrix polynomials. Weisner's group theoretic method is used to obtain matrix generating relations for Charlier matrix polynomials and the details of this method were given in this paper. Finally, we will discuss only briefly the procedure followed.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

The escalating demand for multifunctional and advanced materials for growing industries has turned scientific exploration to graphene-based hybrid filler polymer composites. The introduction of graphene with other fillers into polymer matrices results in astonishing properties and thus has gained significant attention in recent years. This study addresses the significance of graphene-based hybrid filler polymer composites in progressive materials science and engineering. The paper encloses some traditional and current preparation techniques employed in the fabrication of composites and a comprehensive review of successfully prepared graphene hybrid polymer composites with enhanced mechanical, thermal, and electrical properties reported in published research. The role of different factors, e.g., filler type, aspect ratios, filler-matrix compatibility, dispersion effects, homogeneity, filler orientation through polymer matrices, and curing conditions, are summarized. Finally, the applications in heavy industries, e.g., aerospace, electronics, energy storage, and automotive sectors were also analyzed. We hope this study will serve as a practical resource for new researchers and practitioners to understand and harness the full potential of these composites in various scientific and industrial fields.

In this paper, we define Tetranacci and Tetranacci-Lucas matrix sequences and investigate their properties.

Hydrogels can be considered as mimics of extracellular matrix (ECM).Cytoskeleton through integrins is connected with ECM and cytoskeleton tension depends on ECM stiffness.A number of age-related diseases depend on cellular processes related with cytoskeleton function.Some examples of cancer initiation and progression and heart disease in relationship with ECM stiffness has been analysed.Incorporation of rigid particles in ECM can increase ECM stifness and to promote formation of internal residual stresses. Water migration, changes of water binding energy to biomactomolecules, changes of the state of water from tightly bound water to free and loosely bound water changes stiffness of ECM. Risks related with rigid particles incorporation into ECM have been also iscussed.

Cells actively sense differences in topology, matrix elasticity and protein composition of the extracellular microenvironment and adapt their function and morphology. In this study, we focus on the cross-talk between matrix stiffness and protein coating density that regulate morphology and proliferation dynamics of single myocytes. For this, C2C12 myocytes were monitored on L-DOPA functionalized hydrogels of 22 different elasticity and fibronectin density compositions. Static images were recorded and statistically analyzed to determine morphological differences and to identify the optimized extracellular matrix (ECM). Using that information, selected ECMs were used to study the dynamics before and after cell proliferation by statistical comparison of distinct cell states. We observed a fibronectin density independent increase of the projected cell area until 12 kPa. Additionally, changes in the fibronectin density led to an area optimum at about 2.6 μg/cm, which was confirmed by an independent F-actin analysis, revealing a maximum actin filament to cell area ratio of 7.5 %. The proliferation evaluation showed an opposite correlation between cell spreading duration and speed to the matrix elasticity and protein density, which did not affect the cell cycle duration. In summary, we identified an optimized ECM composition, while independent matrix properties regulate distinct cell characteristics.

Polymer hydrogels are 3D networks consisting of hydrophilic crosslinked macromolecular chains, able to swell and retain water. Since their invention in the 1960s, they have become an outstanding pillar in the design, development, and application of engineered polymer systems suitable for biomedical and pharmaceutical applications (such as drug or cell delivery, regeneration of hard and soft tissues, wound healing, and bleeding prevention, among others). Despite several well-established synthetic routes of polymer hydrogels based on batch polymerization techniques, about fifteen years ago academia started to look for alternative methods involving simpler reaction paths, shorter reaction times, and lower energy consumption. In this context, frontal polymerization (FP) undoubtedly has become an alternative and efficient reaction model that allows for converting monomers into polymers via a localized and propagating reaction, by exploiting the formation and propagation of a “hot” polymerization front, able to self-sustain and propagate throughout the monomeric mixture. Therefore, the present work aims to summarize the main research outcomes, achieved during the last years, concerning the design, preparation, and application of FP-derived polymeric hydrogels, demonstrating the feasibility of this technique for the obtainment of functional 3D networks, and providing the reader with some perspectives for the forthcoming years.

Bonchev and Trinajstic defined two distance based entropy measures to measure the molecular branching of molecular graphs in 1977 [Information theory, distance matrix, and molecular branching, J. Chem. Phys., 38 (1977), 4517–4533]. In this paper we use these entropy measures which are based on distance matrices of graphs. The first one is based on distribution of distances in distance matrix and the second one is based on distribution of distances in upper triangular submatrix. We obtain the two entropy measures of paths, stars, complete graphs, cycles and complete bipartite graphs. Finally we obtain the minimal trees with respect to these entropy measures with fixed diameter.

Polymer flooding is one of the most successful chemical EOR methods, and is primarily implemented to accelerate oil production by sweep improvement. However, other benefits have extended the utility of polymers. During the last decade, it has been evaluated for an increasing number of fields, both offshore and onshore. This is a consequence of improved polymer properties, which extends the use to HTHS (high temperature high salinity) conditions and of improved understanding of flow mechanisms such as for heavy oil mobilization. A key issue in understanding polymer performance is to control and predict in-situ porous medium rheology. The first part of this paper reviews recent developments in understanding polymer flow in porous medium. Especially, polymer in-situ rheology and injectivity is discussed. The second part of this paper reports polymer flow experiments using the most applied polymer for EOR processes, HPAM (partially hydrolyzed polyacrylamide). The experiments address high rate near-wellbore behavior (radial flow) as well as reservoir rate steady state flow (linear flow) and discuss differences observed in terms of flow conditions. In addition, impact of oil on polymer rheology was investigated, and compared to single-phase polymer flow in Bentheimer sandstone rock material. Presence of oil leads to a reduction in apparent viscosity.

Matrix metalloproteinases (MMPs) have been demonstrated to have both detrimental and protective functions in inflammatory diseases. Several MMP inhibitors, with the exception of Periostat®, have failed in Phase III clinical trials. As an alternative strategy, recent efforts have been focussed on the development of more selective inhibitors or targeting other domains than their active sites (e.g., exosites, ectosites) through specific small molecule inhibitors or monoclonal antibodies. Here, we present some examples that aim to better understand the mechanisms of conformational changes/allosteric control of MMPs functions. In addition to MMP inhibitors, we discuss unbiased global approaches such as proteomics and N-terminomics to identify new MMP substrates and achieve a better understanding of the roles of these proteases in diseases.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

Introduced in 1967 by Lov\'{a}sz, graph exponentiation has received little attention over the past several decades. Since graph exponentiation produces large graphs and any graph can be constructed utilizing its adjacency matrix, we provide a four step linear construction algorithm that generates the adjacency matrix for the graph exponential.

Biofilm matrix is akin to bacterial abodes, primarily composed of proteins, polysaccharides, extracellular DNA, and lipids, providing essential structural support to bacteria. While some biofilm matrix offers significant benefits, such as engineered biofilm reactors that assist in water pollutant removal, others pose risks to human health, potentially leading to conditions like lung infections. Realizing the potential of advantageous biofilm matrix and mitigating the harmful effects of detrimental ones necessitates a comprehensive and systematic exploration of this intricate domain. To facilitate this examination, our study leveraged a dataset of the 1000 most pivotal papers in the field and conducted an exhaustive bibliographic review. This paper serves as a valuable resource for understanding the current progress in biofilm matrix research and delving into vital avenues for future exploration in this dynamic field.

We report a theoretical derivation of the Cabibbo-Kobayashi-Maskawa (CKM) matrix parameters and the accompanying mixing angles. These results are arrived at from the exceptional Jordan algebra applied to quark states, and from expressing flavor eigenstates (i.e. left-chiral states) as superposition of mass eigenstates (i.e. the right-chiral states) weighted by square-root of mass. Flavor mixing for quarks is mediated by the square-root mass eigenstates, and the mass ratios used have been derived in earlier work from a left-right symmetric extension of the standard model. This permits a construction of the CKM matrix from first principles. There exist only four normed division algebras, they can be listed as follows - the real numbers $\mathbb{R}$, the complex numbers $\mathbb{C}$, the quaternions $\mathbb{H}$ and the octonions $\mathbb{O}$. The first three algebras are fairly well known; however, octonions as algebra are less studied. Recent research has pointed towards the importance of octonions in the study of high energy physics. Clifford algebras and the standard model are being studied closely. The main advantage of this approach is that the spinor representations of the fundamental fermions can be constructed easily here as the left ideals of the algebra. Also the action of various Spin Groups on these representations too can be studied easily. In this work, we build on some recent advances in the field and try to determine the CKM angles from an algebraic framework. We obtain the mixing angle values as $\theta_{12}=11.093^o, \theta_{13}=0.172^o, \theta_{23}=4.054^o$. In comparison, the corresponding experimentally measured values for these angles are $13.04^o \pm 0.05^o, 0.201^o \pm 0.011^o, 2.38^o \pm 0.06^o $. The agreement of theory with experiment is likely to improve when running of quark masses is taken into account.

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

Polyvinyl alcohol (PVA) is highly compatible polymer with biological environments. Specifically, it has been used as a trap for different types of microorganisms in Bio-MEMS, and its properties can be modified to act as an electrode for electrochemical analysis. This study presents a nano-composite developed with PVA, multiwall carbon nanotubes (CNTs) doped with nitrogen, which changes the electrical properties of the polymer and its viscosity to obtain nanofibers by electro-spinning. The proposed nanocomposite was characterized using Fourier transform-infrared and Raman spectroscopy techniques, confirming the presence of the CNTs immersed in the polymer. High-resolution transmission electron microscopy was used to obtain the micrographs that showed the characteristic interplanar distances of the multiwall CNT in the polymeric matrix with values of 3.63 Å. Finally, the CNx mats were exposed to various aqueous solutions in a po-tentiostat to demonstrate the effectiveness of the nanofibers for electrochemical analysis. The CNx-induced changes in the electrical properties of the polymer were identified using cyclic voltammograms, while the electrochemical analysis revealed supercapacitor behavior.

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15%wt) and the sliding regime parameters (load: 1 N, 2.5 N and 5 N, the sliding speed: 0.25 m/s, 0.5 m/s and 0.75 m/s, and the sliding distance: 2500 m, 5000 m and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix.

Gastric inflammation-related disorders are commonly observed digestive system illnesses char-acterized by the activation of proinflammatory cytokines, particularly tumor necrosis factor-α (TNF-α). This results in the induction of cyclooxygenase-2 (COX-2)/prostaglandin E2 (PEG2) and matrix metallopeptidase-9 (MMP-9). These factors contribute to the pathogenesis of gastric in-flammation disorders. We examined the preventive effects of Lonicera japonica Thunb. ethanol ex-tract (Lj-EtOH) on gastric inflammation induced by TNF-α in normal GES-1 cells. The GES-1 cell line was used to establish a model that simulated the overexpression of COX-2/PGE2 and MMP-9 proteins induced by TNF-α, to examine the anti-inflammatory properties of Lj extracts. The re-sults indicated that Lj-EtOH exhibits significant inhibitory effects on COX-2/PEG2 and MMP-9 ac-tivity, attenuates cell migration, and provides protection against TNF-α-induced gastric inflam-mation. The protective effects of Lj-EtOH are associated with the modulation of COX-2/PEG2 and MMP-9 through activation of TNFR–ERK 1/2 signaling pathways as well as the involvement of c-Fos and nuclear factor kappa B (NF-κB) signaling pathways. Based on our findings, Lj-EtOH ex-hibits a preventive effect on human gastric epithelial cells. Consequently, it may represent a novel treatment for the management of gastric inflammation.

Novel tetragonal matrix Ba0.5Gd0.5-xNaxF2.5-x, where x = 0.05, doped by Yb3+, Ho3+, Er3+, was synthesized by molten salt synthesis (MSS) from nitrate flux. XRD data show that tetragonal phase with a = 4.122(1) Å, c = 17.672(1) Å is stable in argon atmosphere up to 960 °C. Luminescence spectra recorded in 500-900 nm and 1050-1700 nm upon 974 nm pumping demonstrated the characteristic luminescence at 1550 nm (4I13/2 → 4I15/2) for Er3+ and 1150 nm (5I6 → 5I8) for Ho3+. The relative thermal sensitivity (Sr) at 296-316 K were 0.3 %*K-1 and 5.5%*К-1 in shortwave infrared (SWIR) and visible range, respectively. Synthesized luminophores can be used as dual-range optical temperature sensors, which simultaneously operating in visible and SWIR ranges.

It is shown that a Mueller quaternion can be formulated as a quaternion with matrix coefficients, and this Mueller quaternion transforms the Stokes quaternion for depolarizing process as well as for nondepolarizing process. Mueller quaternion keeps track of the phase acquired by the Stokes quaternion and, in general, quaternion states of optical media comprises all properties of Jones, Mueller-Jones and Mueller matrices.

This paper is focused on understanding multiscale modelling to obtain a bridge among different time and length scales of simulation techniques. These techniques are vital as it holds the potential to understand and predict the capabilities of polymer nanocomposites (PNCs). However, an appropriate approach in controlling the interfacial interaction between nanoparticle and polymer in nanocomposites structure is still needed to develop. In this review, an initial brief introduction to various trending simulation techniques has been discussed at all three levels of scale (nm, μm, mm). Later, descriptive study on fundamental issues such as thermodynamics, kinetics, mechanical properties, and morphology has been studied deeply. The multiscale modeling bridges the gaps of simulation between the different scales of models from molecular to mesoscale levels working over the broad range of length and timescale. Through the sequential, adaptive, and concurrent approaches, we can develop a system that may comprehend multiscale mode modeling adaptive resolution approach has recently added approach the molecule of the subject can shift their position freely in the domain and through this approach and studied the Brownian motion. Co-The co-current coach is also termed as handshaking path and it is linked aiming at different scale models. Covering the rigid techniques smoothly and linking them at different scales helps in normalizing the statistical behaviour.

Abstract: Congenital cytomegalovirus (cCMV) infection poses significant risks to fetal development, particularly affecting the nervous system. This study reports a fetal autopsy case, examining cCMV infection and focusing on CMV DNA measurements in various fetal organs before formalin fixation, a novel approach for comprehensive CMV DNA evaluations in fetal organs affected by cCMV. A 20-week-old male fetus was diagnosed with cCMV following the detection of CMV DNA in ascites obtained via abdominocentesis in utero. After termination of pregnancy, multiple organs of the fetus, including the cerebrum, thyroid gland, heart, lungs, liver, spleen, kidneys, and adrenal glands, were extracted and examined for CMV DNA loads using real-time polymerase chain reaction. Histopathological examination involved hematoxylin-eosin and CMV-specific immunostaining. A correlation was found between CMV DNA loads and pathology, with higher CMV-infected cell numbers observed in organs positively identified with both staining methods, exhibiting CMV DNA levels of ≥1.0 × 104 copies/mL, compared to those detected solely by CMV-specific immunostaining, where CMV DNA levels ranged from 1.0 x 103 to 1.0 x 104 copies/mL. These results highlight a quantifiable relationship between organ infection extent and CMV DNA concentration, providing insights into cCMV pathogenesis and potentially informing future diagnostic and therapeutic strategies for cCMV infection.

Iyer Markoulakis Helmholtz Hamiltonian mechanics formalisms mathematically modeled physics with vortex rotational fields acting with gradient fields, typically in zero-point microblackhole general fields. Here, Helmholtz metrics have been gaged to Coulombic Hilbert metrics, representing Gilbertian and Amperian natures of electromagnetic fields out of the mechanical fields from Helmholtz Hamiltonian mechanics. This ansatz general gaging helps to properly isolate field effects – mechanical, electric, magnetic components within the analytical processes. Vacuum gravitational fields and the flavor Higgs-Boson matter inertial gravitational fields have been thus quantified extending to stringmetrics constructs matrix showing charge asymmetry gage metrics, having the power to analyze dark energy superluminal phase, dark matter luminal phase, and light matter subluminal phase. Interpreting particle physics gage matrix pointing to Dirac seas electrons, monopoles with positrons, electron-positron annihilation leading to energy production, relativistic energy generating matter, and both monopoles – vacuum and compressed out of vortex Helmholtz decomposition fields have been interpolated. Quantum ASTROPHYSICS gage metrix posits superluminal profile of signals velocity generating electron-positron chain like “curdling” action that is consistent with physics literature reporting nature electron photon observed oscillatory fields configurations. This helps proposing creation of neutrino antineutrino pair orthogonal to electron positron “curdling” planes, that may lead to formation of protonic hydrogen of stars or orthogonally muon. These aspects will explain receding or fast expanding universe with dark matter in terms of flavor metrics versus gage associating metrics flavor. Additional interpretations of virtual gravitational dipoles that have gravitational charge of opposite signs, reported per physics literature at Planck dimensions, that may originate at the center of supermassive blackhole. On the other hands, vacuum monopoles occur probably at infinity with cosmos extent.

We work with reference to a well-known semiclassical model, in which quantum degrees of freedom interact with classical ones. We show that, in the classical limit, it is possible to represent classical results (e.g., classical chaos) by means a pure-state density matrix.

Portfolio weights solely based on risk avoid estimation error from the sample mean, but they are still affected from the misspecification in the sample covariance matrix. To solve this problem, we shrink the covariance matrix towards the Identity, the Variance Identity, the Single-index model, the Common Covariance, the Constant Correlation and the Exponential Weighted Moving Average target matrices. By an extensive Monte Carlo simulation, we offer a comparative study of these target estimators, testing their ability in reproducing the true portfolio weights. We control for the dataset dimensionality and the shrinkage intensity in the Minimum Variance, Inverse Volatility, Equal-risk-contribution and Maximum Diversification portfolios. We find out that the Identity and Variance Identity have very good statistical properties, being well-conditioned also in high-dimensional dataset. In addition, the these two models are the best target towards to shrink: they minimise the misspecification in risk-based portfolio weights, generating estimates very close to the population values. Overall, shrinking the sample covariance matrix helps reducing weights misspecification, especially in the Minimum Variance and the Maximum Diversification portfolios. The Inverse Volatility and the Equal-Risk-Contribution portfolios are less sensitive to covariance misspecification, hence they benefit less from shrinkage.

The aim of this research was to undertake laboratory testing to investigate the beneficial effects of epoxy resin grouts on the physical and mechanical properties of sands with a wide range of granulometric characteristics. Six sands, of different particle size and uniformity coefficients, were grouted using epoxy resin solutions with three ratios of epoxy resin to water (3.0, 2.0 and 1.5). A set of unconfined compressive strength tests were conducted on grouted samples at different curing periods and a set of long-term unconfined compressive creep tests in dry and wet conditions after 180 days of curing were also carried out, in order to evaluate the development of the mechanical properties of the sands, as well as, the impact of water on them. The findings of the investigation showed that epoxy resin resulted in appreciable strength values in the specimens, especially those of fine sands, grouted with the different epoxy resin grouts. In general, the compressive strength varied between 0.68 - 5.60 MPa and the modulus of elasticity between 75 - 480 MPa, after a curing period of 180 days. In terms of physical properties, the permeability and porosity (before and after the grouting process) were estimated. Grouts with an epoxy resin to water ratio of 3 decreased permeability by up to four orders of magnitude. Using laboratory results and regression analysis, three mathematical equations were developed that relate each of the dependent variables; compressive strength, elastic modulus, and coefficient of permeability, with particular explanatory variables.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

Chitosan arouses large interest due to its properties and possible applications. Every year the number of publications and patents based on this polymer increases. Chitosan exhibits poor solubility in neutral and basic media limiting its use in such conditions. Another serious obstacle is directly related to its natural origin. Chitosan is not a single polymer with a defined structure but a family of molecules with differences in their composition, size, and monomer distribution. These properties have a fundamental effect on the biological and technological performance of the polymer. Moreover, some of the biological properties claimed are discrete. In this review, we discuss how chitosan chemistry can solve the problems related to its poor solubility and can boost the polymer properties. We focus on some of the main biological properties of chitosan and the relationship with the physicochemical properties of the polymer. Then, we visit two polymer applications related to green processes: the use of chitosan in the green synthesis of metallic na-noparticles and its use as support in biocatalyst. Finally, we briefly describe how making use of the technological properties of chitosan it is possible to develop a variety of systems for drug delivery

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

This article is devoted to the results of in-depth analysis of the system of binary-oppositional structures in DNA n-plet alphabets and their algebraic-matrix representations. These results show that the molecular complementary replication of DNA strands is accompanied by the presence of an algebraic version of the principle "like begets like" in matrix representations of DNA alphabets having internal structures. This algebraic version is based on binary-oppositional structures in the genetic molecular system, which can be represented by binary numbers and corresponding matrices of DNA alphabets. The received results allow thinking that the phenomenon "like begets like" (or a complementary replication in a wide sense) is systemic in the genetic organization and is connected with algebraic features of biological organization. Correspondingly, the biological principle "like begets like" can be additionally modeled by algebraic-matrix methods and approaches. Such algebra-matrix modeling of the genetic coding system gives new ways for studying and understanding the key role of the named principle in genetic and other inherited physiological complexes. On this way, the author discovered general rules of stochastic organization of information binary sequences of genomic DNAs of eukaryotes and prokaryotes. The presented rules are connected with information dichotomies of probabilities and corresponding fractal-like trees of probabilities, which fundamentally differ from constructional dichotomies in biological bodies. The received phenomenological data and rules lead to new biological ideas.

The extracellular matrix (ECM) is a ubiquitous member of the body and is key to the maintenance of tissues and organs integrity. Initially thought to be a by-stander in many cellular processes, the extracellular matrix has been shown to have diverse components that regulate and activate many cellular processes and ultimately influence cell phenotype. Importantly, the ECM composition, architecture, and stiffness/elasticity influence cellular phenotypes. Under normal conditions and during development, the synthesized ECM is constantly undergoing degradation and remodeling processes via the action of matrix proteases that maintain tissue homeostasis. In many pathological conditions including fibrosis and cancer, the ECM synthesis, remodeling, and degradation is dysregulated causing its integrity to be altered. Both physical and chemical cues from the ECM are sensed via receptors including integrins and play key roles in driving cellular proliferation and differentiation and in various disease progression such as cancers. Advances in ‘omics’ technologies have seen an increase in studies focussing on bi-directional cell-matrix interactions and here we highlight emerging knowledge on the role played by the ECM during normal development and in pathological conditions. This review summarizes current ECM-targeted-therapies that can modify tumor ECM to overcome drug resistance and better cancer treatment.

By constructing a static map, the library robot can navigate and access documents autonomously, which greatly improves efficiency; however, for libraries where shelves can be moved, map changes do not allow for direct navigation, and also sensors such as radar and camera are relatively expensive, so we propose a low-cost navigation algorithm based on real-time ranging data and map matrices, and designed a mobile archive access robot. In order to obtain real-time distance data, nine near/long range sensors were mounted on the chassis and a composite digital filtering algorithm was designed based on different moving area characteristics; then the access task matrix and map matrix were designed based on the archive access task and the location characteristics of the archive shelf placement, the robot can rely on the range data to update the map matrix during the moving process, complete its own positioning, and use the task matrix The robot can use the task matrix to complete autonomous navigation and access to multiple files. Experiments show that the filtered positioning accuracy can reach 1cm, while the robot can move to the target shelf autonomously, which is more practical and less costly.

The paper summarizes in a step by step ‘recipe’ format a model of developing new ideas (Ideation) that can be used to form a new venture or develop a new product. The proposed ‘recipes’ are widely used and can be applied in tandem with other prevalently available models or tools. The intention of the paper is also to serve as a resource for entrepreneurs and innovators, and the links and references munificently used in the paper are serving this purpose. The author has used the outline and the tools described here in numerous Ideation classes taught for over a decade in several countries around the world. The paper’s intention is not to conduct a systematic review on the subject of new venture creation or propose new research agenda (for that, see for example Shepherd et al., 2021). The purpose is to provide an effective and efficient set of tools, models and techniques that can assist the entrepreneur in her journey to create and achieve her dreams. One such tool is the matrix of Reasonings-Outcomes introduced here for the first time.

The bottleneck in creating dynamic models of biological networks and processes often lies in estimating unknown kinetic model parameters from experimental data. In this regard, experimental conditions have a strong influence on parameter identifiability and should therefore be optimized to give the maximum information for parameter estimation. Existing model-based design of experiment (MBDOE) methods commonly rely on the Fisher Information Matrix (FIM) for defining a metric of data informativeness. When the model behavior is highly nonlinear, FIM-based criteria may lead to suboptimal designs since the FIM only accounts for the linear variation of the model outputs with respect to the parameters. In this work, we developed a multi-objective optimization (MOO) MBDOE, where model nonlinearity was taken into consideration through the use of curvature. The proposed MOO MBDOE involved maximizing data informativeness using a FIM-based metric and at the same time minimizing the model curvature. We demonstrated the advantages of the MOO MBDOE over existing FIM-based and other curvature-based MBDOEs in an application to the kinetic modeling of fed-batch fermentation of Baker's yeast.

The recent years various, there huge interest to improve the efficiency of smart electronic and optoelectronic devices via developing emerging materials and printing technologies. However, printing technologies becomes one of the most interesting areas for researcher over a convenient coating method because it not only helps to improve the efficiency of device but also help for rapid, reproducible, and low-cost production which open as a new window for mass production for commercial use. Inkjet printing technology has become the most attractive among various printing technologies due to which it is acceptable in most of scientific and various of industrial applications. This review paper presents an overview of the investigations on formulation of the ink, fabrication, and the applications of conductive polymer via inkjet printing for variety of devices including supercapacitors, sensors, electrochromic devices, and patterning of conductive polymers on flexible substrates. The review covers the different conducting polymer explored for supercapacitors, sensors, electrochromic devices, and patterning of conductive polymers, their ink formulation, inkjet printing process and their keys features. This review also presented future perspectives for inkjet printing technology for advanced electronic, optoelectronic, and other conductive polymer-based devices. We believe this review provides new direction to next generation conductive polymer-based devices for various applications.

In this study, we examine microscale waterflooding in a randomly close-packed porous medium. Three different porosities are prepared in a microfluidic platform and saturated with silicone oil. Optical video fluorescence microscopy is used to track the water front as it flows through the porous packed bed. The degree of water saturation is compared to water containing two different types of chemical modifiers, sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP), with water in the absence of a surfactant used as a control. Image analysis of our video data yield saturation curves and calculate fractal dimension, which we use to identify how morphology changes the way an invading water phase moves through the porous media. An inverse analysis based on the implicit pressure explicit saturation (IMPES) simulation technique uses mobility ratio as an adjustable parameter to fit our experimental saturation curves. The results from our inverse analysis combined with our image analysis show that this platform can be used to evaluate the effectiveness of surfactants or polymers as additives for enhancing the transport of water through an oil-saturated porous medium.

The global polyvinyldene flouride market is estimated to reach $937,278.5 thousand by 2019, therefore to develop new membranes and gain pioneering ideas, which could create innovative business opportunities, a fundamental knowledge about membrane properties fabricated from recent commercially available PVDF polymers is highly mandatory. In this study, we successfully prepared nine non-woven supported PVDF membranes using a phase inversion precipitation method starting from a 15 wt% PVDF solution in N-methyl-2-pyrrolidone. Various membrane morphologies were obtained by using (1) PVDF polymers with diverse molecular weight in a range from 300.000 Da to 700.000 Da and (2) different temperatures of the coagulation bath (20, 40, and 60 ±2°C) used for the films precipitation. Environmental Scanning Electron Microscope (ESEM) was used for surface and cross-section morphologies characterization. Atomic Force Microscope (AFM) was employed to investigate surface roughness, while Contact Angle (CA) instrument was used for membranes wettability studies. Fourier Transform Infrared Spectroscopy (FTIR) results show that the fabricated membranes are formed by a mixture of TGTG’ chains in α phase crystalline domains and all-TTTT trans planar zigzag chains characteristic to β phase. Moreover, generated results indicate that the phases content and membrane morphologies depend on the polymer molecular weight and conditions used for the membranes preparation. The diversity of fabricated membranes could be applied by the End User Industries for different applications.

This paper explores the application of Random Matrix Theory (RMT) as a methodological enhancement for portfolio selection within financial markets. Traditional approaches to portfolio optimization often rely on historical estimates of correlation matrices, particularly susceptible to instability. To address this challenge, we combine a data preprocessing technique based on the Hilbert transformation of returns with RMT to refine the accuracy and robustness of correlation matrix estimation. By contrasting empirical correlations with those derived from random matrices, we uncover non-random properties and underlying relationships within financial data. We then utilize this methodology to construct the correlation network dependence structure used in portfolio optimization. The empirical analysis presented in this paper validates the effectiveness of RMT in enhancing portfolio diversification and risk management strategies. This research contributes by offering investors and portfolio managers with methodological insights to construct portfolios that are more stable, robust, and diversified. At the same time, it advances our comprehension of the intricate statistical principles underlying multivariate financial data.

Matrix-variate Gaussian type or Wishart type distributions in the real domain are widely used in the literature. When the exponential trace has an arbitrary power and when a factor involving a determinant enters into the model or a matrix-variate gamma type or Wishart type model with exponential trace having an arbitrary power, is extremely difficult to handle. Evaluation of the normalizing constant in such a model is the most important part because when studying the properties of such a model, the method used in the evaluation of the normalizing constant will be the relevant steps in all the computations involved. One such model with a factor involving a trace and the exponential trace having an arbitrary power, in the real domain, is known in the literature as Kotz' model. No explicit evaluation of the normalizing constant in the model involving trace with an exponent and determinant with an exponent entering into the model and at the same time the exponential trace having an arbitrary exponent seems to be available in the literature. The normalizing constant widely used in the literature and interpreted as the normalizing constant in the general model and refers to as a Kotz' model does not seem to be correct. Corresponding model in the complex domain, with the correct normalizing constant, does not seem to be available in the literature. One of the main contributions in this paper is the matrix-variate distributions in the complex domain belonging to Gaussian type, gamma type, type-1 and type-2 beta type when the exponential trace has an arbitrary power. All these models are believed to be new. A second main contribution is the explicit evaluation of the the normalizing constants, in the real and complex domains especially in the complex domain, in a matrix-variate model involving a determinant and a trace as multiplicative factors and at the same time the exponential trace having an arbitrary power. Another main contribution is the introduction of matrix-variate models with exponential trace having an arbitrary exponent, in the categories of type-1 beta, type-2 beta and gamma distributions or in the family of Mathai's pathway models [1], both in the real and complex domains. Another new contribution is the logistic-based extensions of models in the real and complex domains with exponential trace having an arbitrary exponent and connecting to extended zeta functions introduced by this author recently. Some properties of such models are indicated but not derived in detail in order to limit the size of the paper. The techniques and steps used at various stages in this paper will be highly useful for people working in multivariate statistical analysis as well as people applying such models in engineering problems, communication theory, quantum physics and related areas, apart from statistical applications.

Matrix metalloproteinases are involved in extracellular matrix remodeling through the degradation of extracellular matrix components and are involved in the inflammatory response by regulating the activities of TNF-alpha and IL-1beta, which are pro-inflammatory cytokines, in addition to extracellular matrix components. Since the regulation of inflammatory response and changes in the extracellular matrix by MMPs are related to the development of various diseases including lung and cardiovascular diseases, many studies have been conducted on the role of MMPs in pathogenesis. In addition, various studies have demonstrated that MMPs are involved in the pathogenesis of infectious diseases by regulating the expression and activity of MMPs by infection with pathogens. In this review, we discuss the role of MMPs in infectious diseases and the role of MMPs in inflammatory responses and present their potential as therapeutic targets in infectious diseases.

The theory of one-photon ionization and two-photon above-threshold ionization is formulated for applications to heavy atoms in attosecond science using the Dirac-Fock formalism. A direct comparison of the Wigner-Smith-Eisenbud delays for photoionization is made with delays from the Reconstruction of Attosecond Beating By Interference of Two-photon Transitions (RABBIT) method. Photoionization by an attosecond pulse train, consisting of monochromatic fields in the extreme ultraviolet range, is computed with many-body effects at the level of the Relativistic Random Phase Approximation (RRPA). Subsequent absorption and emission processes of infrared laser photons in RABBIT are evaluated using static ionic potentials as well as asymptotic properties of relativistic Coulomb functions. As expected, light elements, such as Argon, show negligible relativistic effects, while heavier elements, such a Krypton and Xenon, exhibit delays that depend on the fine-structure of the ionic target. The relativistic effects are notable close to ionization thresholds and Cooper minima with differences in fine-structure delays predicted to be as large as tens of attoseconds. The separability of relativistic RABBIT delays into a Wigner-Smith-Eisenbud delay and a universal continuum--continuum delay is studied with reasonable separability found for photoelectrons emitted along the laser polarization axis in agreement with prior non-relativistic results.

Formalism proofing general derivation, applying matrix properties operations, showing fundamental relationships with inner product to outer product has been advanced here. This general proof formalism has direct application with physics to quantify quantum density at micro scale level to time commutator at macro scale level. System of operator algebraic equations have been rigorously derived to obtain analytic solutions which are physically acceptable. Extended physics application will include metricizing towards unitarization to achieve gaging Hamiltonian mechanics to electromagnetic gravitational strong theory, towards grand unifying physics atomistic to astrophysics or vice versa via quantum relativistic general physics thereby patching to classical physics fields energy.

The matrix converter converts the input line voltage into a variable voltage with an unrestricted output frequency without using an intermediate circuit, dc link circuit. A pure sine in and pure sine out is the unique feature of the matrix converter. This research paper also analyzes the basic operating principle and the simulation modeling of the direct matrix converter, which is controlled by the Space Vector Pulse Width Modulation technique by using the software which is known as MATLAB/Simulink. The most desirable features in the power frequency changes can be fulfilled by using the matrix converters, and this is the reason for the tremendous interest in the topology. Since the power electronic circuits which is known as the motor drives are used to operate the AC motors at the frequencies other than that of the supply.

An oil and vinegar scheme is a signature scheme based on multivariate quadratic polynomials over finite fields. The system of polynomials contains $n$ variables, divided into two groups: $v$ vinegar variables and $o$ oil variables. The scheme is called balanced (OV) or unbalanced (UOV), depending on whether $v = 0$ or not, respectively. These schemes are very fast and require modest computational resources, which make them ideal for low-cost devices such as smart cards. However, the OV scheme has been already proven to be insecure and the UOV scheme has been proven to be very vulnerable for many parameter choices. In this paper, we propose a new multivariate public key signature whose central map consists of a set of polynomials obtained from the multiplication of block matrices. Our construction is motivated by the design of the Simple Matrix Scheme for Encryption and the UOV scheme. We show that it is secure against the Separation Method, which can be used to attack the UOV scheme, and against the Rank Attack, which is one of the deadliest attacks against multivariate public-key cryptosystems. Some theoretical results on matrices with polynomial entries are also given, to support the construction of the scheme.

This paper attempts to extend the Riemann Zeta function of a complex number to a function of a matrix and/or a tensor $A$, namely $$\zeta (A)=\sum _{n=1}^{\infty} \frac{1}{n^{A}}= \sum _{n=1}^{\infty} \sum_{k=1}^n\lambda_k A^k$$ and inverse $$A=\sum _{n=1}^{\infty} \sum_{k=1}^n \mu(n)\lambda_k \zeta(A^k)$$ where $\mu(n)$ is the M\"obius function, $A$ is a complex matrix or tensor with any order, and $\lambda_k$ is eigenvalue of the matri/tensor $A$. This kind of calculations on the Riemann Zeta function has never been seen in the literature. Some examples are provided.

Metal nanoparticles are used to modify/enhance the properties of a polymer matrix for a broad range of applications in bio-nanotechnology. Here, we study the properties of polymer/gold nanoparticle (NP) nanocomposites through atomistic molecular dynamics, MD, simulations. We probe the structural, conformational and dynamical properties of polymer chains at the vicinity of a gold (Au) NP and a functionalized (core/shell) Au NP, and compare them against the behavior of bulk PE. The bare Au NPs were constructed via a systematic methodology starting from ab-initio calculations and an atomistic Wulff construction algorithm resulting in the crystal shape with the minimum surface energy. For the functionalized NPs the interactions between gold atoms and chemically adsorbed functional groups change their shape. As a model polymer matrix we consider polyethylene of different molecular lengths, from the oligomer to unentangled Rouse like systems. By computing the different properties the concept of the interface, and the interphase as well, in polymer nanocomposites with metal NPs are critically examined. Results concerning polymer density profiles, bond order parameter, segmental and terminal dynamics show clearly that the size of the interface / interphase, depends on the actual property under study. In addition, the anchored polymeric chains change the behavior/properties, and especially the chain density profile and the dynamics, of the polymer chain at the vicinity of the Au NP.

Long-acting (LA) drug-delivery system (DDS) successes are linked to their abilities to harness biocompatible polymers and materials for sustained and predictable release of therapeutic agents over an extended period of time. For human immune deficiency virus type one (HIV-1) infections, LA DDSs hold great promise in closing the gaps of daily oral therapy for treatment and prevention. Examples are Cabenuva, Apretude and Sunlenca, which have been shown to be safe and effective. Alternative promising drug delivery technologies such as implants, prodrugs, vaginal rings, and microarray patches are being explored to further meet patients’ needs. We posit that improved physicochemical properties of the formulation payloads and material chemistry design with optimal drug release kinetics holds the potential to optimize release profiles. Furthermore, for the treatment and prevention of HIV-1 infection, the landscape of LA medicines now in clinical or preclinical development offers hope that the strategic design of polymers will further improve upon controlled delivery of drugs to simplify dosing schedules.

Temperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in hazardous working environments (air pollution, chemical or ionizing contamination), and the presence of electromagnetic disturbances. The use of fiber optic temperature sensors in polymer technology can significantly reduce the cost of their production. Moreover, the installation process and usage would be simplified. As a result, these types of sensors would becoming increasingly popular in industrial solutions. This review provides a critical overview of the latest development of fiber optic temperature sensors based on Fabry-Perot interferometer made with polymer technology.

Nanometer-curved surfaces are abundant in biological systems as well as in nano-sized technologies. Properly functionalized polymer-grafted nanoparticles (PGNs) adhere to surfaces with different geometries and curvatures. This work explores some of the energetic and mechanical characteristics of the adhesion of PGNs to surfaces with positive, negative and zero curvatures using Coarse-Grained Molecular Dynamics (CGMD) simulations. Our calculated free energies of binding of the PGN to the curved and flat surfaces as a function of separation distance show that curvature of the surfaces critically impacts the adhesion strength. We find that the flat surface is the most adhesive, and the concave surface is the least adhesive surface. This somewhat counterintuitive finding suggests that while a bare nanoparticle is more likely to adhere to a positively curved surface than a flat surface, grafting polymer chains to the nanoparticle surface inverts this behavior. Moreover, we studied the rheological behavior of PGN upon separation from the flat and curved surfaces under external pulling force. The results presented herein can be exploited in drug delivery and self-assembly applications.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

Hybrid inorganic-polymer nanocomposites can be employed in diverse applications due to the potential combination of desired properties from both the organic and inorganic components. The use of novel bottom-up in situ synthesis methods for the fabrication of these nanocomposites is advantageous compared to top-down ex situ mixing methods, as it offers increased control over the structure and properties of the material. In this review, the focus will be on the application of the sol-gel process for the synthesis of inorganic oxide nanoparticles in epoxy and polysiloxane matrices. The effect of the synthesis conditions and the reactants used on the inorganic structures formed, the interactions between the polymer chains and the inorganic nanoparticles, and the resulting properties of the nanocomposites are appraised from several studies over the last two decades. Lastly, alternative in situ techniques and the applications of various polymer-inorganic oxide nanocomposites are briefly discussed.

Polymer nanocomposites are composed of polymer materials reinforced with nano fillers. In the present study the effective thermal conductivity of the composites filled with nanofillers has been investigated using commercially available finite element software ABAQUS 6.11. The nanofillers used were alumina particles and multi-walled carbon nanotubes (MWNTs) and the matrix was considered to be made of epoxy. For the analysis 2D and 3D Representative Volume Elements (RVEs) were generated using Random Sequential Adsorption (RSA) algorithm using MATLAB and Python scripts. Thermal conductivity was found out for 2D and 3D RVEs for different area and weight fractions respectively. Two different shapes of the alumina nanoparticles were considered: spherical (circular) and ellipsoidal (elliptical) for 3D (2D) analysis. It was found that the thermal conductivity was increased with the addition of nanofillers. The increase in thermal conductivity was approximately same for both types of inclusions at corresponding area or weight fractions in 2D or 3D analysis. The results showed that addition of MWNTs to the composites lead to a significant increase in thermal conductivity than spherical or ellipsoidal inclusions.

Epoxy matrix composites reinforced with high-performance fibers such as carbon, Kevlar, and glass, exhibit excellent specific stiffness and strength in many mechanical applications. However, these composites are disappointingly non-recyclable and are usually disposed of in landfill sites, with no realistic prospect for biodegradation in reasonable time. In contrast, moldable composites with carbonized elastomeric matrices developed in the last decades possess attractive mechanical properties in final net-shape products and can also be incinerated or recycled. Many carbon and inorganic fillers have recently been evaluated to adjust the properties of carbonized elastomeric composites. Renewable organic fillers such as human or animal hair offer an attractive fibrous material with substantial potential for reinforcing composites with elastomeric matrices. Samples of unidirectional fiber composites (with hair volume fraction up to 7 %) and quasi-isotropic short fiber composites (with hair volume fraction up to 20 %) of human hair-reinforced nitrile butadiene rubbers (HH-NBR) were produced in the peroxide-cured and carbonized states. The samples were characterized using SEM, Raman spectroscopy and photoacoustic microscopy. Mechanical tests were performed in tension using a miniature universal testing machine. The expected effect of fiber reinforcement on the overall mechanical performance has been demonstrated for both cured and carbonized composites. Considerable enhancement of the elastic modulus (up to 10 times), ultimate tensile strength (up to 3 times) and damage tolerance was achieved. The evidence of satisfactory interfacial bonding between hair and rubber was confirmed by SEM imaging of fracture surfaces. The suitability of photoacoustic microscopy was assessed for 3D reconstruction of the fiber sub-system spatial distribution and non-destructive testing.

(1) Background: Breast cancer is a frequent heterogeneous disorder diagnosed in woman and is a high cause of mortality of them in reason to rapid metastasis and disease recurrence. Ferroptosis can inhibit breast cancer cell growth, improve the sensitivity of chemotherapy and radiotherapy and inhibit distant metastases so potentially acts on tumor micro-environment; (2) Methods: Ferroptosis/Extracellular matrix remodeling literature text-mining results were integrated in breast cancer transcriptome cohort according their distant relapse free survival (DRFS) under adjuvant therapy (anthracyclin+taxanes) and also in MDA-MB-231 transcriptome functional experiments with ferroptosis activations (GSE173905); (3) Results: Ferroptosis/Extracellular matrix remodeling text-mining identified 910 associated genes in at list 10 articles. Univariate Cox analyses censored on breast cancer (GSE25066) selected 252 individual significant genes and 171 of them found with an adverse expression. Functional enrichment of these 171 adverse genes predicted basal breast cancer signatures. By text-mining some ferroptosis significant adverse selected genes shared citations in domain of ECM remodeling such as: TNF, IL6, SET, CDKN2A, EGFR, HMGB1, KRAS, MET, LCN2, HIF1A, TLR4. A molecular score based on expression the eleven genes was found predictive of worst prognosis breast cancer at univariate level: basal subtype, short DRFS, high grade values 3 and 4, estrogen and progesterone receptors negative and nodal stages 2 and 3. This eleven gene signature was validated as regulated by ferroptosis inductors (erastin and RSL3) in triple negative breast cancer cellular model MDA-MB-231.; (4) Conclusions: Crosstalk between ECM remodeling-Ferroptosis functionalities allowed to define a molecular score which have been characterized as an independent adverse parameter in prognosis of breast cancer patients. Gene signature of this molecular score have been validated to be regulated by erastin/RSL3 ferroptosis activators. This molecular score could be promising to evaluate ECM impact of ferroptosis target therapies in breast cancer.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Lithium-ion batteries (LIBs) have become indispensable energy storage devices for various applications, ranging from portable electronics to electric vehicles and renewable energy systems. The performance and reliability of LIBs depend on several key components, including the electrodes, separators, and electrolytes. Among these, the choice of binder materials for the electrodes plays a critical role in determining the overall performance and durability of LIBs. This review introduces polymer binders that have been traditionally used in the cathode, anode, and separator materials of LIBs. Furthermore, it explores the problems identified in traditional polymer binders and examines the research trends in next-generation polymer binder materials for lithium-ion battery as alternatives.

The selection of biomaterials for biomedical application is a significant challenge. In the last few decades, various bioabsorbable and stable biopolymers have been applied for use as biomedical devices in orthopedic applications. Ultra-high molecular weight polyethylene (UHMWPE) has been extensively used in medical implants, notably in the bearings of hip, knee, and other joint prostheses, owing to its biocompatibility and high wear resistance. For the ACL graft, synthetic UHMWPE is an ideal candidate due to its biocompatibility and its extremely high tensile strength. Despite the appeal of new advanced materials such as carbon fiber, poly-ether-ether ketone, and other load-bearing materials, UHMWPE remains a primary load-bearing candidate material for ACL reconstructions because of its extremely high strength, the simplicity of the fabrication process, its biocompatibility, and low friction. However, some significant problems are observed in UHMWPE based implants, such as wear debris, and oxidative degradation due to the generation of free radicals when exposed to irradiation with gamma rays for grafting or sterilization. Various innovative methodologies have been developed to resolve those problems and enhance the properties of UHMWPE. In this review, we will explore in detail the methods for surface functionalization of UHMWPE and will apply these findings to the case study of UHMWPE for Anterior Cruciate Ligament repair.

In this scientific research, thermally stable nickel nanoparticles were synthesized and characterized. Nickel nanoparticles were synthesized using phenol –formaldehyde by chemical method followed by calcination. The polymer metal complex was confirmed by FTIR and NMR. The spherical morphology of nickel nanoparticles confirmed by SEM. The crystallographic structure is confirmed by XRD and size of cobalt nanoparticles is 24.0 nm. The TGA analysis was performed over a range of 29-600OC. The TGA thermograph predicts mass decomposition of 11%, for nickel phenol-formaldehyde nanocomposite. The decomposition rate of composites is very low 2% weight loss per 100OC increment in temperature.

Herein, we present preparation of solid polymer electrolyte (SPE) comprising of PEO, NaPF₆ and varying fraction of Succinonitrile (SN) by standard solution cast technique. The morphological features and structural properties were studied by the FESEM, XRD, respectively. FTIR was performed to study the interactions between polymer host, salt, and SN. Impedance spectroscopy, Transference number measurements, LSV and CV were used to examine the electrochemical properties. The complex permittivity/conductivity & modulus were studied to understand the dielectric properties by evaluating the dielectric strength, relaxation time, hopping frequency and dc conductivity. Based on the experimental results an interaction mechanism is presented.

A complex square matrix $A$ is said to be Hermitian if $A= A^{\ast}$, the conjugate transpose of $A$. The topic of the present note is concerned with the characterization of Hermitian matrix. In this note, the we show that each of the two triple matrix product equalities $AA^{\ast}A = A^{\ast}AA^{\ast}$ and $A^3 = AA^{\ast}A$ implies that $A$ is Hermitian by means of decompositions and determinants of matrices, which are named the two-sided removal and cancellation laws associated with Hermitian matrix, respectively. We also present several general removal and cancellation laws as the extensions of the preceding two facts about Hermitian matrix.

Dual quaternions have wide applications in automatic differentiation, computer graphics, mechanics and others. Due to its application in control theory, the matrix equation AXB=C has been extensively studied. However, there is currently limited information on matrix equation AXB=C over the dual quaternion algebra. In this paper, we provide the necessary and sufficient conditions for the solvability of the dual quaternion matrix equation AXB=C, and present the expression for the general solution when it is solvable. As an application, we derive the ϕ-Hermitian solutions for the dual quaternion matrix equation AXAϕ=C, where the ϕ-Hermitian extends the concepts of Hermiticity and η-Hermiticity. Lastly, we present a numerical example to verify the main research results of this paper.

In this paper, we introduce ResNetMF, a groundbreaking approach that harnesses the power of residual network matrix factorization to revolutionize recommendation systems. ResNetMF integrates residual networks, renowned for their ability to capture intricate patterns and features, with matrix factorization techniques that excel in modelling user-item interactions. This fusion presents a novel solution that surpasses the limitations of traditional recommendation systems. Through comprehensive experimentation and evaluation of diverse datasets, ResNetMF demonstrates remarkable enhancements in recommendation accuracy and efficiency. By effectively capturing both linear and nonlinear relationships in user-item interactions, ResNetMF provides superior recommendation quality. The outcomes from experiments unequivocally highlight the superiority of ResNetMF over existing state-of-the-art recommendation approaches, thereby validating its innovative nature and underscoring its potential to shape the future of recommendation systems. Through the integration of the deep residual network, ResNetMF approach facilitates the training of neural networks, enabling them to explore the underlying data layers more comprehensively. Extensive experimentation and evaluation across various datasets provide compelling evidence for the superiority of ResNetMF. Moreover, the proposed method utilized natural language processing (NLP) techniques for targeted information dissemination in recommendation systems, emphasizing the importance of personalized and relevant recommendations for user satisfaction and engagement.

There is need to address the challenges of organ shortage, through development of tissues and organs with alternatives to those of the allograft-kind. This illustrates the quest behind novel biofabrication strategies such as 3D bio-printing, which is necessary to create artificial multi-cellular tissues/organs. Several findings have been reported in this review. First, the role of ECM components in tissue regenerative medicine is presented. Different ECM components such as collagen, gelatin, elastin, fibronectin, laminins and glycosaminoglycans are concisely examined for their tissue regenerative medicine applications. Next, current state of research on extrusion-based 3D bio-printing techniques and their limitations are reviewed. For example, we show that cell viability is still a challenge with extrusion, while the use of natural polymers such as collagen in improving composites’ mechanical properties is limited. Lastly, we examine unresolved research questions necessary to advance the present state of research in the field.

Many bio-applicable materials, medical devices, and prosthetics combine both polymer and metal components to benefit from their complementary properties. This goal is normally achieved by their mechanical bonding or casting only. Here, we report an alternative easy method for the chemical grafting of a polymer on the surfaces of a metal or metal alloys using alkoxy amine salt as a coupling agent. The surface morphology of the created composites was studied by various microscopy methods, and their surface area and porosity were determined by adsorption/desorption nitrogen isotherms. The surface chemical composition was also examined by various spectroscopy techniques and electrokinetic analysis. Elements distribution on the surface was determined and successful bonding of the metal/alloys on one side with the polymer on the other one was confirmed by alkoxy amine. The composites show significantly increased wettability, reliable chemical stability of the bonding, excellent bacterial anti-adhesive properties and functionality, i.e. the characteristics promising for their application in biomedical field.