The structure and physicochemical properties of polyvinyl alcohol (PVA) and PVA/glycerol films have been investigated by Fourier-transform infrared spectroscopy (FT-IR), X-ray Diffraction (XRD), thermogravimetry/differential thermal analysis (TG/DTA), and advanced scanning probe microscopy (SPM). In the pure PVA films, SPM allowed us to observe ribbon-shaped domains with a different frictional and elastic contrast, which apparently originated from a correlated growth or assembly of PVA crystalline nuclei located within individual PVA clusters. The incorporation of 1.0 wt.% glycerol led to modification in shape of those domains from ribbon-like in pure PVA to rounded in PVA/glycerol 1.0 wt.% films; changes in the relative intensities of the XRD peaks and a decrease of the amorphous halo in the XRD pattern were also detected, while the DTA peak corresponding to the melting point remained at almost the same temperature. For higher glycerol content, FT-IR revealed additional glycerol-characteristic peaks presumably related to the formation of glycerol aggregates, and XRD, FT-IR, and DTA all indicated a reduction in crystallinity. For more than 2.0 wt.% glycerol, the plasticization of the films complicated the acquisition of SPM images without tip-induced surface modification. Our study contributes to the understanding of crystallinity in PVA and how it is altered by a plasticizer such as glycerol.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

This paper addresses the capability to alter the wettability characteristics of poly(vinyl alcohol) (PVA) polymer films doped with glycerol. Films of PVA and glycerol-choline chloride (GCC) blends have been prepared by solution casting method with different glycerol dopants ranging from 0% to 10% (wt %). The results show that as the dopant content increases from 0% to 10%, the wettability increases and hence increases the surface energy of the solid film. The wettability changes are observed by identifying the contact angle of 10 µL deionized water droplet which altered from 55o to 28o as dopant content changed from 0% to 10% per PVA solution weight. The results show that the roughness of film surfaces increases as the content of dopant (GCC) increases in the film which indicates that roughness has a strong influence on the wettability of the casted films.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

Vinyltriethoxysilane (VTES) was covalently bonded onto graphene oxide. Several methods, including X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and X-ray diffraction, were used to demonstrate the presence of VTES on the surface of graphene oxide and the creation of this covalent link. Following that, different quantities of the resultant vinyltriethoxysilane functionalized graphene oxide (VTESFGO) were mixed with polyvinyl alcohol (PVA) to form VTESFGO/PVA nanocomposite films (NCFs) with a 3-dimensional network structure. The creation of these NCFs and the presence of a three-dimensional network were confirmed by Fourier transform infrared spectroscopy. The three-dimensional network structure provided these NCFs extraordinary characteristics. The mechanical and thermal stability, oxygen transfer rate (OTR), and water resistance pressure (WRP) of the NCFs were investigated. The nanocomposite film (NCF) with the highest weight percentage of VTESFGO (3.0 wt.%) was 47.5% more thermally stable than pure PVA, with an oxygen transmission rate of 0.3 cm3/m2 per day and a water resistance pressure of 780 mm/cm2. However, as the weight percentage of VTESFGO increased, the mechanical strength of the NCFs decreased as a result of silanol self-condensation, resulting in particulate formation, as confirmed by scanning electron microscopy.

Anthocyanins extract from purple tomato (PTA) was incorporated with polyvinyl alcohol (PVA) so that a series of colorimetric films of PVA/PTA (based on PVA) were prepared. The role of anthocyanin on color response, FTIR, thickness, water content, mechanical properties, antioxidant activity, and permeation of water vapor through the films was examined. In addition, its application in smart packaging to assess the freshness of shrimp was studied. It was found that the tensile strength, contact angle and WVP of PVA/PTA films increases with the addition of more PTA, while the elongation at break and water content decreased. FTIR analysis showed that there are interactions between PTA and PVA matrix. The addition of anthocyanins caused to a significant improvement for the antioxidant properties of PVA films. Furthermore, the total volatile alkaline nitrogen (TVB-N), total plate count (TPC) and pH value of shrimp were monitored after 4 days of refrigeration, and the color change of the indexes was recorded. The PVA/PTA films changed color from purple to yellow-green during the storage time of 0-4d for shrimp, this suggests that the film could be used in smart packaging as a real-time freshness indicator for shrimp.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

In this study, a slow-release urea fertilizer hydrogel was synthesized from hydroxyl propyl methyl cellulose, polyvinyl alcohol and glycerol blends with paper (blended paper) as second layer. The fertilizer hydrogel was characterized by SEM, XRD and FTIR. Its retention in sandy soil, swelling behavior in distilled and tap water as well as slow-release behavior to urea were investigated. The results indicated that the fertilizer had good slow-release properties and ability to retain water in soil. However, the addition of blended paper as a second layer matrix was found to help improve the release properties of the fertilizer. The swelling kinetic of the hydrogel followed the Schott’s Second order model. The release kinetics of urea in water was best described by the Zero order model signifying that the release behavior was independent of fertilizer concentration

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

The design of an antimicrobial coating materials becomes ideal in order to prevent infections caused by the transmision of pathogens coming from human’s contact with contaminated surfaces. In that aim layered single hydroxides (LSH) and layered double hydroxides (LDH) containing Zn and Cu, in nitrate form and intercalated with antimicrobial molecules, were synthe-sized and characterized. Cinnamate and salicylate anions were chosen to be intercalated in the fillers because of their well known antimicrobial activity. Several coatings based on polyvinyl alcohol (PVA) and LDH or LSH with increasing amounts of filler were prepared and filmed on a polyethylene terephthalate (PET) substrate. Coatings were characterized and their antimi-crobial activity was evaluated against pathogens critical in nosocomial infections, giving interesting results.

The pursuit of an environmentally sustainable manufacturing process advocates for the substitution of harmful reagents for less damaging and recyclable solutions. This study aims to assess the effectiveness of using cellulose microfibrils synthesized via different hydrolysis reactions as reinforcing agents in polyvinyl alcohol (PVA) at varying con-centrations. The investigation explores the morphology, thermal properties, and chemi-cal behavior of the cellulose particles. The cellulose microfibrils (CMF) produced using citric acid exhibited the highest yield and aspect ratio. Notably, particles from organic acids demonstrated greater thermal stability, with oxalic acid-derived particles displaying the maximum thermal degrada-tion temperature. Subsequently, cast films of PVA reinforced with the cellulose microfibrils underwent comprehensive analyses, including Fourier transfer infrared (FTIR) spectroscopy, thermal degradation temperature (Td), differential scanning calorimetry (DSC), and tensile strength tests. The thermal behavior of cast films experienced notable changes with the addition of cellulose particles, evidenced by increased melting and crystallinity temperatures, along with a rise in the degree of crystallinity. The incorporation of cellulose particles led to a substantial improvement in mechanical properties. Films containing CMF dis-played higher Young’s modulus, and the sample incorporating 5% CMF derived from citric acid exhibited the most significant increase in modulus.

Abstract: This study aims to analyze the physico-mechanical properties and dynamic models of tissue-simulating hydrogels, specifically the photoacoustic (PA) response signals, by varying the concentrations of polyvinyl alcohol (PVA) and molecular weight (MW). A state space model (SSM) is proposed to study the PVA hydrogels to retrieve the PA-related signal's damping ratio and nat-ural frequency. Nine box-shaped PVA hydrogels containing saline solution were used, with five concentrations of PVA (7, 9, 12, 15, 20%) for MW1 and four for MW2. The results indicated that the concentration of PVA and MW played an important role in the PA wave's amplitude, arrival time, and speed of sound over the hydrogels. The SSM parameters showed that increasing PVA and MW concentrations improved the hydrogels' ability to absorb and transfer energy under the PA effect. These parameters were also found to be correlated with density and modulus of elasticity. Addi-tionally, the concentrations of PVA and MW affected the absorption and optical scattering coeffi-cients. The physical-mechanical properties, including porosity, density, and modulus of elasticity, improved as the concentration of PVA and MW increased. The ultimate goal of this study is to develop hydrogels as phantoms that can be used for tissue simulation and imaging.

In order to improve the strength of PVA/xylan composite films and endow them with ultraviolet (UV) shielding ability, TiO2-KH550 nanoparticle was synthesized and added into the PVA/xylan matrix. The TiO2-KH550 nanoparticle dispersed well in the 0.04% sodium hexametaphosphate (SHMP) solution under ultrasonic and stirring treatments. Investigations on the properties of films showed that TiO2-KH550 had the positive impact on improving the strength, moisture and oxygen barrier properties of the composite films. The maximum tensile strength (27.3 MPa), the minimum water vapor permeability (2.75×10-11 g•m-1•s-1•Pa-1) and oxygen permeability (4.013 cm3•m-2•24h-1•0.1MPa-1) were obtained under the addition of 1.5% TiO2-KH550. The tensile strength of TiO2-KH550 reinforced composite film was increased by 70% than that of the pure PVA/xylan composite film, and the water vapor and oxygen permeability were decreased by 31% and 41%, respectively. Moreover, the UV transmittance of film at the wavelength of 400 nm was almost zero when adding 1.5~2.5% of TiO2-KH550, which indicated the PVA/xylan composite films were endowed with excellent UV light shielding ability.

This article discusses the fabrication of pullulan/polyvinyl alcohol (PVA) and PVA blends as carrier polymers for drug delivery. This study utilized coaxial electrospinning to encapsulate doxorubicin (DOX), a common anticancer drug, within nanofibers, which helped mitigate the adverse effects of DOX on normal cells. The study also demonstrated that the coaxial electrospinning technique using PVA/pullulan cores was effective in inhibiting the attachment and proliferation of HeLa cells, a type of cervical cancer cell. The use of pullulan/PVA and PVA blends as carrier polymers in conjunction with coaxial electrospinning could provide a safe and effective drug delivery system for the treatment of cervical and other solid malignancies. The study concluded that nanofibers showed promising results in inhibiting the growth of HeLa cells, indicating their potential as safe and effective drug delivery systems for treating cervical cancer and other solid malignant tumors.

We report the synthesis and characterization of Poly Methyl-Meth-Acrylate (PMMA)/Poly vinylalcohol (PVA) polymeric blend doped with different concentrations of Copper oxide (CuO) nanoparticles (NPs). The (PMMA-PVA)/CuO nanocomposite hybrid thin films (wt. % = 0%, 2%, 4%, 8%, and 16%) of CuO NPs are deposited on glass substrates via dip-coating technique. The transmittance (T%), reflectance (R%), the absorption coefficient (α), the optical constants [refractive index (n), extinction coefficient (k)], optical dielectric functions [ɛ',ɛ''] are investigated and interpreted. Tauc, Urbach, Spitzer-Fan, and Drude models are employed to calculate the optical bandgap energy (Eg) and the optoelectronic parameters of the nanocomposite thin films. The refractive index and optical bandgap energy of of (PMMA-PVA) polymeric thin film are found to be (1.5 to 1.85) and 4.101 eV, respectively. Incorporation of specific concentrations of CuO-NPs in (PMMA-PVA) polymeric thin films leads to a noticeable decrease in the optical bandgap energy and to an increase of the refractive index. Moreover, Fourier Transform Infrared Spectroscopy (FTIR) transmittance spectra are measured and analyzed for undoped and doped polymeric thin films to pinpoint the major vibrational modes in the spectral range (500 and 4000 cm-1), as well as, the nature of network bonding in both systems. Thermal stability of thin films is investigated by performing thermogravimetric analysis (TGA). The TGA thermograms confirm that both doped polymeric thin films are thermally stable at temperatures below 110°C which enables them to be attractive for a wide range of optical and optoelectronic applications. Our results indicate that optical, vibrational and thermal properties of both polymeric thin films can be tuned for specific applications by the appropriate corporation of particular concentrations of CuO-NPs.

In order to design effective protective coatings against corrosion, the polyvinyl alcohol (PVA) as compound and composite with silver nanoparticles (nAg/PVA) were electrodeposited on copper surface employing electrochemical techniques such as linear potentiometry and cyclic voltammetry. A new paradigm was used to distinguish the features of coatings, i.e., a Deep Convolutional Neural Network (CNN) was implemented to automatically and hierarchically extract the discriminative characteristics from the information given by optical microscopy images. The main arguments that invoke a CNN implementation in the surface science of materials are the following: artificial intelligence techniques can be successfully applied to learn differences between surface coatings; based on their popularity for image processing, CNN can model images related to the problem of coatings; deep learning is able to extract the features that are distinguishable between material surfaces. To provide an overview of the copper surface, CNN was applied on microscope slides (CNN@microscopy) and inherently learnt distinctive characteristics for each class of surface morphology. The material surface morphology controlled by CNN without the interference of the human factor was successfully conducted, in our study, to extract the similarities/differences between unprotected and protected surfaces to establish the PVA and nAg/PVA performance to retard the copper corrosion.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

In this study, multilayer composite nanofiber membranes of sodium alginate (SA) /polyethyleneimine (PEI)/polyvinyl alcohol (PVA) was fabricated via electrospinning technique to enhance the adsorption of Cu2+ from wastewater. The preparation and adsorption mechanisms of the SA/PEI/PVA nanofiber membranes were analyzed by utilizing analytical techniques such as SEM, FTIR, EDS, UV-vis, XRD, and TG. The obtained nanofiber membrane characterized by small diameter, high uniformity, and extensive surface area, demonstrate significant potential for heavy metal ion filtration. Optimal spinning parameters were identified, including a voltage of 19.5 KV, a distance of 8 cm, and specific mass ratios (SA: PEI: PVA, 1:2:6) and injection speeds (8 μL/min) and. The resulting nanofibers with an average diameter of 112.5 nm exhibited excellent morphology and high efficiency, retaining over 85% adsorption capacity for Cu2+ in initial tests and maintaining above 80% efficacy through four successive filtration cycles.

We report on the effects of the film morphology on the fluorescence spectra for a thin film including a quinoxaline-based co-polymer (TQ1) and a fullerene derivative (PC₇₀BM). The ratio between the polymer and the fullerene derivative, as well as the processing solvent were varied. Beside the main emission peak at 700 nm in the fluorescence spectra of thin films of this phase-separated blend, a broad emission band is observed with a maximum at 520 - 550 nm. The intensity of this emission band decreases with an increasing degree of mixing in the film and becomes most prominent in thicker films, films with high PC₇₀BM content, and films that were spin-coated from solvents with lower PC₇₀BM solubility. We assign this emission band to aggregated PC₇₀BM.

This paper presents a proof-of-concept study on the biocolonization of 3D-printed hydroxyapatite scaffolds with mesenchymal stem cells (MSCs). Three-dimensional (3D) printed biomimetic bone structure made of Calcium Deficient HydroxyApatite (CDHA) intended as future bone graft was made from newly developed composite material for FDM printing. The biopolymer polyvinyl alcohol serves in this material as a thermoplastic binder for 3D molding of the printed object with a passive function and is completely removed during sintering. The study presents the material, the process of fused deposition modeling (FDM) of CDHA scaffolds and its post-processing at three temperatures (1200, 1300, 1400 °C), as well it evaluates the cytotoxicity and biocompatibility of scaffolds with MTT and LDH release assays after 14 days. The study also includes a morphological evaluation of the cellular colonization with scanning electron microscopy (SEM) in two different filament orientations (rectilinear and gyroid). The results of the MTT assay showed that the tested material was not toxic, and cells were preserved in both orientations, with most cells present on the material fired at 1300°C. Results of the LDH release assay showed a slight increase in LDH leakage from all samples. Visual evaluation of SEM confirmed the ideal post-processing temperature of the 3D-printed FDM framework for samples fired at 1300°C and 1400°C, with a porosity of 0.3 mm between filaments. In conclusion, the presented fabrication and colonization of CDHA scaffolds have great potential to be used in the tissue engineering of bones.

Agriculture technical development exclusively relies on the effective delivery of agrochemicals and water to the plants and reduce the harmful effects of the agrochemicals on the useful organisms in the soil. Wherefore, super absorbent hydrogels were prepared by copolymerization of gum Arabic (GA) with chitosan (CS) or poly(vinyl alcohol) (PVA), and cross-linked by N,’N-methylenebisacrylamide (MBA) chemically (CH) or using sodium hexametaphosphate (SHMP) as physical (PH) cross-linker. The prepared hydrogels include PVA/GA-CH, PVA/GA-PH, CS/GA-CH and CS/GA-PH showed different degree of swelling (DS) in the following swelling medium, deionized water (DW), river water(RW) and buffer solution pH9. PVA/GA-CH and CS/GA-CH hydrogels have showed 84g/g and 63g/g maximum DS in RW respectively, while PVA/GA-PH and CS/GA-PH hydrogels have showed 81g/g and 69g/g maximum DS in pH9 respectively. The water- retention capability of some hydrogels were studied using a mixture of 0.5%(w/w) hydrogel in agricultural soil and the composite showed about 20 days extra retain of water with a control sample of soil alone. The hydrogels were loaded using urea the important fertilizer in agriculture field. The hydrogels of higher DS were only loaded, where PVA/GA-CH hydrogel has shown 89%(w/w) maximum loading percentage (Lmax%), and CS/GA-PH hydrogel reached 79.75%(w/w) of urea. The release behavior in different medium and degree of temperatures of loaded hydrogels were studied. Generally, PVA/GA-CH hydrogel have shown better release profile in RW medium at 10oC, while CS/GA-PH hydrogel showed more controlled release in pH9 medium at 30oC. Different analytical methods of SEM, FTIR of loaded hydrogel and after their release were achieved, whereas XRD,1H NMR and (TGA, DSC) of prepared hydrogels have been characterized.

The aim of this research study was to develop hydrogels samples for using in potential biomedical applications. Hydrogels consisting of different volumes of keratin, polyvinyl alcohol (PVA), Polyvinylpyrrolidone (PVP), and starch. The keratin is derived from the chicken was the primary material on the hydrogels due to attractively for the potential wound healing application. The hydrogel samples were made by using the freeze‑thawing method, and they were examined using the Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), porosity amusement, swelling ratio and keratin release kinetic models that analyzed using (zero-order, first-order Higuchi and Korsmeyer-Peppas models). These results were indicated that feather keratin could use with formulated hydrogels suitably for controlled keratin release studies .

Frequent and excessive consumption of alcohol, be it episodic or sustained misuse, ranks among the top causes of mortality globally. This comprehensive analysis seeks to elucidate how alcohol misuse precipitates death, with a particular focus on associated cardiac anomalies. Notably, the phenomenon of "Holiday Heart Syndrome," linked to binge drinking, is recognized for inducing potentially fatal cardiac arrhythmias. Moreover, persistent alcohol consumption is implicated in the development of alcoholic cardiomyopathy, a condition that underlies heart failure and arrhythmic disturbances of the heart. Additionally, individuals undergoing withdrawal from alcohol frequently exhibit disruptions in normal heart rhythm, posing a risk of death. This review further delves into additional alcohol-related mortality factors, including the heightened likelihood of hypertension, cerebrovascular accidents (strokes), and the connection between excessive alcohol use and Takotsubo syndrome.

Scaffolds are widely used in tissue engineering because their manufacture is based on natural and synthetic polymers, which allows them to have properties such as biocompatibility and biodegradability, creating an ideal environment for cell growth on their surface. In this context, among the polymers studied in Tissue Engineering are Chitosan (CH) and Polyvinyl Alcohol (PVA). CH is a versatile polymer obtained from de-acetylation of chitin, which is used for its high biodegradability and biocompatibility, although its mechanical properties must be improved. It has been found that one of the ways to improve the mechanical properties of CH is to mix it with other synthetic polymers such as PVA. PVA is known for its biocompatibility, biodegradability, zero toxicity and ease of preparation due to its solubility in water and excellent mechanical properties, such as tensile strength and ease in the formation of films and barriers. In this study we evaluated the capacity of scaffolds made with CH and PVA in different concentrations (2: 1, 1: 1, 1: 2, respectively) as a possible application in bone regeneration. This was made through different characterization tests such as Infrared Spectroscopy, AFM, Swelling test and Porosity test, where we obtained information about its structural and physicochemical properties. Additionally, a cellular quality control was performed on the material through the MTT assay. The Fourier transform infrared spectroscopy (FTIR) study showed that there are strong intermolecular hydrogen bonds between the chitosan and polyvinyl alcohol molecules. The Swelling and Porosity tests showed favorable results, obtaining maximum values ​​of 5519% and 72.17% respectively. MTT tests determined that the prepared materials are not cytotoxic. These findings suggest that scaffolds possess properties suitable for use in Tissue Engineering.

Pyrolyzed organic matter – commonly referred to as biochar – generally has positive effects on plant growth and can enhance early seedling development. Biochar-based seed coatings may thus be beneficial, specifically under adverse soil conditions such as high soil salinity. We evaluated germination and early plant development in radish (Raphinus sativa) seeds coated with conifer-feedstock slow-pyrolysis biochar; following the precedent of prior studies, polyvinyl acetate (PVAc) was used as the binding agent. Biochar-based seed coatings reduced germination rates and radicle extension in Petri dish trials; however, leaching of coated seeds largely eliminated this effect. PVAc applied in solution inhibited seed germination to a similar extent, suggesting that toxicity of PVAc or chemical products derived from it is the main mechanism for germination inhibition; a meta-analysis of published literature also indicates negative effects of biochar-based seed coatings using PVAc. In greenhouse trials the same biochar seed coatings improved aspects of plant growth and physiological status relative to controls, specifically enhancing root development. We conclude that biochar-based seed coatings have promise in promoting early seedling growth, and in combating salinity stress in agronomic and restoration applications. However, our findings contraindicate PVAc use as a binding agent. Further research is needed to test non-phytotoxic, readily biodegradable binding agents and to optimize biochars and seed coating processes for specific applications in agronomy and ecological restoration.

Hazardous chemicals like toxic organic dyes are very harmful to the environment and their removal is quite challenging. Therefore there is a necessity to develop techniques, which are environment friendly, cost-effective and easily available in nature for water purification and re-mediation. The present research work is focused on the development` and characterization of the ecofriendly polyvinyl alcohol (PVA) and alginate (Alg) hydrogel beads incorporating natural bentonite (Bent) clay as beneficial adsorbents for removal of toxic methylene blue (MB) from industrial water. PVA−Alg/Bent nanocomposite hydrogel beads with different Bent content (0, 10, 20, and 30 wt%) were synthesized via external ionic gelation method. The designed porous and steady structure beads were characterized by the use of Fourier transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDX), and scanning electron microscopy (SEM). The performance of the beads as MB adsorbents was investigated by treating batch aqueous solutions. The experimental results indicated that the incorporation of Bent (30 w%) in the nanocomposite formulation sustained porous structure, preserved water uptake, and increased MB removal effi-ciency by 230 % compared to empty beads. Designed beads possessed higher affinity to MB at high pH 8, 30 °C, and fitted well to pseudo-second-order kinetic model a high correlation coefficient. Moreover, designed beads had a good stability and reusability as they exhibited excellent removal efficiency (90%) after six consecutive adsorption-desorption cycles. Adsorption process was found be combination of both monolayer adsorption on homogeneous surface and multilayer adsorption on heterogeneous surface. The maximum adsorption capacity of the designed beads system as calculated by Langmuir isotherm was found to be 51.34 mg/g, which is in good agreement with the reported clay-related adsorbents. The designed PVA−Alg/Bent nanocomposite hydrogel beads demonstrated good adsorbent properties and could be potentially used for MB removal from polluted water.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

: Intracellular tripeptide glutathione is an important agent of cell survival in hypoxia. Glutathione covalently binds to SH-groups of hemoglobin cysteine residues, protecting them from irreversible oxidation and changes its affinity to oxygen. Reduced glutathione (GSH) can also form a non-covalent complex with hemoglobin. Previously, we showed that hemoglobin tetramer has four noncovalent binding sites of glutathione GSH molecules inside, two of which are released during hemoglobin transition to deoxy form. In this study, we characterized the conserved cysteine residues and residues of non-covalent glutathione binding sites in the sequences of a number of hypoxia tolerant and hypoxia-sensitive mammals. The alpha subunit of all species considered was found to have no conserved cysteines, whereas the beta subunit contains Cys94 residue, which is conserved across species and whose glutathionylation changes the affinity of hemoglobin for oxygen 5-6-fold. In addition, the key residues of noncovalent glutathione binding sites in both alpha and beta subunits are absolutely conserved in all species considered, suggesting a common mechanism of hemoglobin redox regulation for both hypoxia-sensitive and hypoxia-tolerant mammals. The solvent accessibility of all HbA and HbB residues in oxy- and deoxy- forms was analyzed. The key residue betaCys94 is solvent accessible only in the deoxy form.

The focus of this article is the evaluation of the quality and the degree of community engagement in an expert-based, public-health communicative intervention for Alcohol Use Disorder (AUD). In 2023 the Canadian Alcohol Use Disorder Society collaborated with a grass-roots community health group, a regional health authority, and an academic participatory researcher to organize a working group to mount a social-marketing campaign to increase community support for AUD medical treatment in family-practice settings in a rural community in British Columbia. The partnership working group conducted a series of activities in the school system, the town council, and the community. This article covers the formative evaluation and the summative evaluation of the working group's effectiveness. The formative evaluation ("lessons learned" and "recommendations") consists of consensus evaluations of the quality of each activity using a variety of data sources. The formative evaluation followed improvement science methods and used consensus meetings to provide and reflect on formal and informal feedback. Formative results reflect the consensus of the participants in the working group and they record the reactions in the community. The summative evaluation measures evidence of community engagement found in transcribed text from meeting minutes. The summative evaluation used theory-based frameworks and text data visualization to assess the engagement dynamics of the working group. The summative evaluation helps to put the formative evaluation into perspective as communicative action. The summative evaluation validates the formative evaluation by revealing the communicative dynamics of engagement which resulted in the community’s increased capacity to understand and support Alcohol Use Disorder Treatment options. The working group and the entire intervention was seen by the participants and the public as a success and capable of replication. In a small community, it instilled new understandings and attitudes, bringing an emerging awareness of medication as an optional health mitigation strategy for Alcohol Use Disorder. Our study furthers this overall assessment by using theoretical constructs and analysis of communicative records to trace engagement characteristics of interest to researchers, societies, and community groups contemplating similar interventions in the future. The study also validates the effectiveness of communicative analysis as a measure of social-marketing for expert-based public health interventions.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.

The composites of heteropolyacids (H3PW12, H3PMo12) incorporated into amine-functionalized silica materials, were used for the first time as heterogeneous catalysts in the valorisation of glycerol (a large waste from biodiesel industry) by acetalization reaction with acetone. The polyoxotungstate catalyst H3PW12@AptesSBA-15 presented higher catalytic efficiency than the phosphomolybdate, with 97% of conversion with 97% of solketal selectivity, after 60 min at 25 °C, or 91% of glycerol conversion and the same selectivity, after 5 min, performing the reaction at 60 ºC. A relation of catalytic performance and acidity of the catalyst is here presented. Furthermore, the stability of the solid catalyst was investigated and discussed.

Fused deposition modeling (FDM) is a rather new technology in the production of personalized dosage forms. Melting and printing of polymer–active pharmaceutical ingredient (API) – mixtures can be used to produce oral dosage forms with different dosage as well as release behavior. This process is utilized to increase the bioavailability of pharmaceutically relevant active ingredients that are poorly soluble in physiological medium by transforming them into solid amorphous dispersions (ASD). Release from such ASDs is expected to be faster and higher compared to the raw materials and thus enhance bioavailability. Printing directly from powder while forming ASDs was realized. Different techniques to change release patterns as well as a non-destructive way for determination of API distribution were shown. By measuring the melt viscosities of mixtures printed a rheological model for the printer used is proposed.

The development of biofuels and biodiesel industry specifically, has resulted in the generation of large amounts of glycerol as a surplus. The conversion of glycerol, into chemicals with indus-trial interest, through anaerobic fermentation using E. coli as a biocatalyst is an attractive alter-native to improve economic performance in the biodiesel industry, for example through the bi-otransformation of residual glycerol into ethanol. For 2019, the size of the global ethanol market was valued at $ 89.1 billion US dollar. Biodiesel can be produced from several materials like rapeseed, palm, soya, corn, palm kernel, frying oil or olive-pomace oil (OPO). The last, can be extracted from alperujo, byproduct of olive oil process. However, olive-pomace oil converting into biodiesel is not enough established to achieve a global olive-oil/biodiesel derived process with minimized waste generation. Traditionally biodiesel production process produces an equivalent of 10% by mass of glycerol as a waste or by-product. This work explores the conver-sion of residual glycerol into chemicals like ethanol and hydrogen with a focus on projecting raw material potential availability from OPO, contributing to the promotion of the use of biofu-els and biodegradable compounds.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

A series of supported CuO-based nanoparticle catalysts were prepared by impregnation method and used for the synthesis of glycerol carbonate from glycerol and CO2 in the presence of 2-cyanopyridine as a dehydrant and DMF as a solvent. The effects of supports (activated alumina, silicon dioxide, graphene oxide, graphene, and activated carbon), CuO loading amount, calcination temperature, and reaction parameters on the catalytic activity of catalyst were investigated in detail. XRD, FTIR, SEM, BET, and CO2-TPD were used for the characterization of the prepared catalysts. It is found that CuO/Al2O3 shows a higher catalytic activity, which depends on the CuO loading amount and calcination temperature. The surface area and amount of basic sites of the catalyst exhibit crucial effect on the catalytic activity of CuO/Al2O3. Furthermore, there is a synergistic effect between the catalyst and 2-cyanopyridine that the former has higher activation ability for glycerol and the latter acts not only as a dehydrant, but also as a promoter for CO2 activation. Recycling experiments reveal that this catalyst can be reused at least five cycles without any inactivation. Based on the experiment results and FTIR characterization, a possible reaction mechanism for the carbonylation of glycerol and CO2 is proposed.

While the number of publications on wine and health is steadily increasing, ranging from molecular level to epidemiological studies, often with contradictory results, little attention has been given to an holistic approach. In this review some unusual concepts are considered, such as phytocomplex, vehicle and the Matrix effect. As an example, three mono/polyphenols present in wine, Tyrosol, Hydroxytyrosol and Resveratrol, have been selected and the consequences of respecting, disregarding or ignoring the Matrix effect are shown. Underestimation of the wine Matrix effect could lead to deceiving results, as in the case of de-alcoholized wine or wine-compound-based nutritional supplements,or in emphasizing a single component toxic activity, in this case alcohol, ignoring the specific protective action at molecular level of other compounds (polyphenols) present in the same Matrix. The dark side of Matrix effect is also discussed. It is suggested that specificity of wine should be always taken in consideration by public health Authorities.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Glycerol conversion to valuable biomolecules has been a research avenue that has attracted a significant interest in recent years due to its increasing over production, with possibilities for chemical transformation for eco-friendly processes and distinct compounds with biological activities. Also, in the current climate change in which a major emphasis is being placed on the design of green processes, solvents are key factors from both an economic and environmental point of view. In this context, due to its abundance and low-price, glycerol represents an innovative solvent coming from biomass and produce in high amount. On the other hand, Epichlorydrin, Glycidol and Solketal have become useful intermediates in chemical transformations when using glycerol as a raw material. This review focuses on glycerol as a green solvent in the synthesis of complex molecules, Epichlorydrin, Glycidol, Solketal and Tosyl solketal as an efficient recycling process for glycerol, as well as building blocks in the synthesis of glycerol derivatives, which are undeniable new source of potentials drugs.

Owing to the growing concerns due to dwindling fossil fuel reserves, increasing energy demand and climate emergency, it is imperative to develop and deploy sustainable energy technologies to ensure future energy supply as well as transition to the net zero world. In this context, there is great potential in the biorefinery concept for supplying drop in biofuels in the form of biodiesel. Biodiesel as a fuel can certainly bridge the gap where electrification or the use of hydrogen is not feasible, for instance heavy vehicles, farm and marine transportation sector. However, biodiesel industry also leads to formation of large amount of crude glycerol as the byproduct. Crude glycerol due to presence of several impurities may not be a suitable feedstock for all high value products derived from glycerol but fits well with glycerol esterification for producing glycerol acetins, which have numerous applications. This review critically looks at the processes using nanostructured solid/liquid acid catalysts for glycerol esterification including the economic viability of the scale up.

In this study, nanostructured cerium-doped TiO2 (Ce-TiO2) films with the addition of different amounts of cerium (0.00, 0.08, 0.40, 0.80, 2.40, and 4.10 wt. %) were deposited on a borosilicate glass substrate, by flow coating sol-gel process. After flow coating, deposited films were dried at the temperature of 100 °C for 1 h, followed by calcination at the temperature of 450 °C for 2 h. For the characterization of sol-gel TiO2 films, the following analytic techniques were used: X-ray diffraction (XRD), thermal gravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry (DSC). Sol-gel derived Ce-TiO2 films were used for photocatalytic degrada-tion of the ciprofloxacin (CIP). The influence of the amount of Ce in TiO2 films, the duration of the photocatalytic decomposition, and the irradiation type (UV-A and simulated solar light) on the CIP degradation were monitored. Kinetics parameters (reaction kinetics constants and the half-life) of the CIP degradation, as well as photocatalytic degradation efficiency, were determined. The best photocatalytic activity was achieved by the TiO2 film doped with 0.08 wt.% Ce, under both UV-A, and solar irradiation.

One of the hallmarks of Alzheimer’s disease (AD) is the accumulation of beta-amyloid peptide (Aβ) leading to formation of soluble neurotoxic Aβ oligomers and insoluble amyloid plaques in various parts of the brain. Aβ undergoes post-translational modifications that alter its pathogenic properties. Aβ is produced not only in brain, but also in the peripheral tissues. Such Aβ, including its post-translationally modified forms, can enter the brain from circulation by binding to RAGE and contribute to the pathology of AD. However, the transport of modified forms of Aβ across the blood–brain barrier (BBB) has not been investigated. Here, we used a transwell BBB model as a controlled environment for permeability studies. We found that Aβ42 containing isomerized Asp7 residue (iso-Aβ42) and Aβ42 containing phosphorylated Ser8 residue crossed the BBB better than unmodified Aβ42, which correlated with different contribution of endocytosis mechanisms to the transport of these isoforms. Using microscale thermophoresis, we observed that RAGE binds to iso-Aβ42 an order of magnitude weaker than to Aβ42. Thus, post-translational modifications of Aβ increase the rate of its transport across the BBB and modify the mechanisms of the transport, which may be important for AD pathology and treatment.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

A great deal of studies have assessed the expression of noncoding RNAs (ncRNAs) as well as their relevant molecular functions and biological mechanisms in the individuals of alcohol dependence. Alcohol dependence is one of the most prevalent neuropsychological disorders worldwide, and its pathogenesis is intricate and inadequately understood. There is considerable evidence demonstrating substantial links between multiple genetic factors and the development of alcohol dependence. Critical roles of ncRNAs have been emphasized in the pathophysiology of mental diseases including alcohol dependence. In the comprehension of ncRNAs action and their mechanisms of modification, they have emerged as therapeutic targets for a variety of psychiatric illness including alcohol dependence. Worth mentioning, dysregulated expression of ncRNAs has been regularly detected in individuals of alcohol dependence. An in-depth knowledge of roles of ncRNAs and m6A modification may be valuable for the development of a novel treatment against alcohol dependence. In general, a deeper comprehension of functional roles ncRNAs may make significant contributions to the precise diagnosis and/or actual treatment of alcohol dependence. Here in this review, we mostly focused on the up-to-date knowledge regarding alterations and/or modifications in the expression of ncRNAs in alcohol dependence, and then, presented their prospects for future research and therapeutic application with a novel concept of engram-system.

Recently, polyacetylene (PA) is receiving a renewed scientific attention due to its electrical properties potentially useful for energy applications (e.g., fabrication of electrodes for batteries and supercapacitors) and unique functional characteristics (e.g., flame retardant, oxygen scavenger, EMI-shielding, etc.). This chemical compound can be obtained in form of a polyacetylene-PVOH copolymers simply by chemical dehydration of poly(vinyl alcohol) (PVOH), which is a very common type of polymer, widely used in packaging and other technological areas. This very inexpensive chemical reaction for the large-scale synthesis of PA/polyvinylenes has been investigated by reacting PVOH with fuming sulfuric acid at room temperature. In this process, PVOH, shaped in form of film, is dipped in fuming sulfuric acid (i.e., H₂SO₄ at 95-97%) and, after complete chemical-dehydration, it has been mechanically removed from the liquid phase by using a nylon sieve. The reduction process leads to a substantial PVOH film conversion to PA as it has been proved by infrared spectroscopy (ATR-mode). Indeed, the ATR spectrum of the reaction product included all characteristic absorption bands of PA. The reaction product has been also characterized by UV-Vis spectroscopy in order to evidence the presence in the structure of conjugated carbon-carbon double bonds of various lengths. Differential scanning calorimetry (DSC) and thermogravimetric analysis have been used respectively to investigate the PA solid-state cis-trans isomerization and thermal stability in air and nitrogen, respectively.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

Walls-like structured monoclinic WO3 thin films were obtained by spray deposition method for further integration in gas sensors. For sensing applications, it is very important to achieve a high surface-to-volume ratio surface together with a proper thin films structure. The present communication reports on the effect of the sprayed solution volume variation (as a thickness variation element) on the detailed Raman spectroscopy for WO3 thin films with different thicknesses grown from precursor solutions with two different concentrations. Detailed analysis of the two series of samples shows that the growing thickness strongly affects the films morphology while their crystalline structure is only slightly affected. The Raman analysis contribute to refining the structural features clarifications. It was observed that, for both concentrations, the increase in thickness seems to slightly affect the stoichiometry of material and, in association with surface morphology variations, provide new possibilities for fine tuning of films properties towards enhanced as sensing applications. Further studies are ongoing.

Polyvinyl guanidineacetic (PVG) was prepared by the chemical grafting between poly(vinyl alcohol) (PVA) and guanidineacetic acid. The results showed that the guanidineacetic groups were successfully introduced into the polyvinyl alcohol by fourier transform infrared (FTIR) and thermogravimetry (TG). The effects of the amount of catalyst and reaction time on the PVG grafting rate were investigated. The PVG/NWF composite membrane as a heterogeneous catalyst for biodiesel production was successfully prepared by the solvent phase inversion. The effects of mass ratio of methanol/soybean oil and reaction temperature on the conversions using the composite membrane for transesterification were studied. And the reusability of the composite membrane and the kinetics of the reaction catalyzed by the composite membrane were also investigated. The conversions obtained from the model are in good agreement with the experimental data.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a Ultra-high performance concrete (UHPC) has gained worldwide popularity because of its notable mechanical response. This research studied the compressive strength, modulus of elasticity, and flexural tensile strength of UHPC. Batches were made with the addition of steel and PVA fibers using a standard procedure defined in the research. The experimental data from the compressive strength test was analyzed in the Statistica 10 software to investigate the fibers' influence on UHPC's mechanical properties. An analysis of the elastic modulus prediction was carried out according to international standards. It was found that the normalized equations for the elastic modulus are not adequate for its estimation. The statistical analysis indicated that the range of fiber quantities analyzed did not significantly affect the compressive strength and the elastic modulus. Regarding the optimized mix, its flexural tensile strength indicates that the fiber content must be higher for UHPC to be suitable for structural use.

Alcoholic liver disease (ALD) develops when the immunotolerant environment of the liver is compromised due to excessive alcohol consumption. ALD progression involves variations in the expression of multiple genes, resulting in liver inflammation and the development of a leaky gut. Molecular mechanism involved for ALD progression is still unclear, and due to that there are currently no FDA-approved drugs available for its treatment. In this study, the protective effects of Graphene oxide nanoparticles (GO) was investigated against ethanol-induced damage in the gut-liver axis in in vitro. GO was synthesized using a modified Hummer's method and characterization was done. Given the general concerns regarding nanoparticle toxicity, assessment of cell viability, lipid accumulation, DNA damage, cell death, and the generation of reactive oxygen species (ROS) were conducted using various techniques. Furthermore, gene expression of pro- and anti-inflammatory cytokines was done using RT-qPCR. The findings revealed that GOs promoted cell viability even against ethanol treatment. Additionally, lipid accumulation significantly decreased when cells were treated with GO alongside ethanol compared to ethanol treatment alone, with similar trends observed for other assays. Gene expression analysis indicated that GO treatment reduced the expression of proinflammatory cytokines while enhancing the expression of antioxidant genes. Moreover, GO treatment led to improvements in gut permeability and a reduction in proinflammatory cytokines in colon cells damaged by ethanol. These findings suggest that GO holds promise as a drug carrier, exhibiting no observed toxic effects. By shedding light on the protective effects of GO against ethanol-induced damage, this study contributes to the burgeoning field of nanoparticle-mediated therapy for ALD.

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15%wt) and the sliding regime parameters (load: 1 N, 2.5 N and 5 N, the sliding speed: 0.25 m/s, 0.5 m/s and 0.75 m/s, and the sliding distance: 2500 m, 5000 m and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix.

This study explored the effects of cryogenic treatment on the microstructure, hardness, and wear-resistance of diamond-like carbon (DLC) by cryogenically treating NAK 80 mold steel coated with DLC. Raman spectroscopy analyzed the structure of the DLC film. Nanoindenter analyzed the hardness and Young’s modulus of the film, and their relationship determined the wear resistance. Wear test assessed the wear rate and friction coefficient of the DLC film. The results showed that cryogenic treatment increased the rate of carbide precipitation and refined the grain structure. Raman spectroscopy indicated that the Raman intensity rate (I_D/I_G) of treated DLC films was smaller than those without cryogenic treatment. When the sp3 bond increased, the hardness and wear-resistance of the DLC film also increased.

Core chlorophytes possess glycerol-3-phosphate dehydrogenases (GPDs) with an unusual bidomain structure, consisting of a glycerol-3-phosphate phosphatase (GPP) domain fused to canonical GPD domains. These plastid-localized enzymes have been implicated in stress responses, being required for the synthesis of glycerol under high salinity and triacylglycerols under nutrient deprivation. However, their regulation under varying environmental conditions is poorly understood. C. reinhardtii transgenic strains expressing constitutively bidomain GPD2 did not accumulate glycerol or triacylglycerols in the absence of any environmental stress. Although, the glycerol contents of both wild type and transgenic strains increased significantly upon exposure to high salinity. Cycloheximide, an inhibitor of cytoplasmic protein synthesis, abolished this response in the wild type. In contrast, GPD2 transgenic strains were still capable of glycerol accumulation when cultured in medium containing cycloheximide and NaCl. Thus, pre-existing GPD2 protein appears to become activated for glycerol synthesis upon salt stress. Interestingly, staurosporine, a non-specific inhibitor of protein kinases, prevented this post-translational GPD2 protein activation. Structural modeling analyses suggested that substantial conformational rearrangements, possibly triggered by high salinity, may characterize an active GPD2 GPP domain. Understanding this mechanism(s) may provide insights into the rapid acclimation responses of microalgae to osmotic/salinity stress.

Cardiotonic steroids (CTS) are a group of steroid compounds derived from certain plants and animals. CTS are selective inhibitors of Na,K-ATPase, so for a long time they were widely used for medical purposes to treat heart failure and some other diseases. However, over time, doctors gradually began to refuse this group of drugs due to their narrow therapeutic range and a number of serious side effects. However, in parallel with the rise and fall of interest in CTS as a drug, interest in them as a single class of high-affinity Na,K-ATPase inhibitors has only increased. Numerous data on the effect of CTS on signaling cascades and cell viability made impelling a search for a rationale for the existence of such a subtle biological regulator. A large number of studies devoted to the potential use of CTS in the treatment of neurodegenerative, oncological, immune and other diseases "revitalized" the already "written off" group of the drugs. If initially the role of exogenous (mainly plant origin) CTS was studied, then by the 90s of the XX century the study of the role of endogenous CTS and their regulatory effects became a popular trend in biology and physiology. The role of endogenous CTS was studied in details in the pathogenesis of cardiovascular diseases [1]. A large number of researchers have unanimously stated that endogenous CTS are very complex regulators of the development of pathological processes; however, the exact cause-and-effect relationship that would unambiguously explain the processes of synthesis, utilization, and the role of endogenous CTS has not yet been established. The effects of CTS in the frame of various regulatory schemes have been described, but the predominant number of studies was devoted to arterial hypertension, heart and renal failure, cancer [2–4], aging [5,6], and neuroinflammation. The effects of both endo- and exogenous CTS on blood cells and have been studied to a much lesser extent.

Biodiesel has several drawbacks, such as being prone to oxidation, having reduced stability, and having limited storage time. Antioxidants compatible with biodiesel are being used to address its drawbacks. Utilizing antioxidants effectively improves the quality of biodiesel. Enhancing the quality of biodiesel for use as a clean energy source benefits both the global economy and ecology. Therefore, we believe that our work will contribute to the advancement of the worldwide industry. The study used blends consisting of 20% biodiesel and 80% diesel fuel. Isatin-thiosemicarbazones were tested as additives in blends at a concentration of 3000 parts per million (ppm) using an oxifast device. Comparing them to the chemical antioxidant Trolox. FT-IR, DSC, and TGA were used to characterize these samples. DSC measured sample crystallization temperatures (Tc). Samples with antioxidants showed decreased values compared to the non-antioxidant diesel sample D100. Several DSC tests were conducted to determine the antioxidant strengths of various samples. The results showed that the FT-IR spectrum's antioxidant effect regions grow clearer with antioxidants. The extra antioxidant is effective. Biodiesel's oxidative stability improves with isatin-thiosemicarbazones at varying concentrations. The kinetics of thermal decomposition of isatin-thiosemicarbazones under non-isothermal conditions have been determined using the Kissinger, Ozawa, and Boswell techniques. The activation energies of compounds 1 and 2 were calculated 137–147 kJ mol^-1 and 173–183 kJ mol^-1, respectively.

Polyvinyl chloride (PVC) electric wires were subjected to dechlorination in subcritical water at three different temperatures in a high-pressure reactor. About 2.09, 73.08 and 95.96 wt. % of chlorine in PVC wires was removed during dechlorination at 200, 250 and 300 °C, respectively. The solid residues were analyzed and characterized by thermogravimetry, at three different heating rates (5, 10 and 20 °C/min) in inert and oxidizing atmosphere. With the purpose of studying the emission of chlorinated pollutants, pyrolysis experiments at 850 °C were also performed in a laboratory scale reactor with the dechlorinated materials, as well as with the original PVC electric wire. Polycyclic aromatic hydrocarbons (PAH) formation increased, but chlorobenzenes (ClBz) and chlorophenols (ClPh) formation decreased as the temperature of dechlorination increased; naphthalene was the most abundant PAH and monochlorobenzene and monochlorinated phenols (3-+4-) were the most abundant chlorinated compounds.

Biodegradable poly(ɛ-caprolactone) (PCL) and its composites or blends have gotten a lot of attention in the last decade because of their potential applications in human life and environmental remediation. As a result, there is a growing interest in the synthesis of PCL-composites/blends and their applications. Greater efforts have been made to develop biodegradable chemical materials as adsorbents that do not pollute the environment in order to replace traditional materials. Among the numerous types of degradable materials, PCL is currently the most promising, the most popular, and the best material to be developed, and it is referred to as the "green" eco-friendly material. Membranes and adsorbents for water treatment, packaging and compost bags, controlled drug carriers, biomaterials for tissues such as bone, cartilage, ligament, skeletal muscle, skin, cardiovascular and nerve tissues are just some of the applications of this biodegradable polymer (PCL). The goal of this review is to present a brief overview of PCL, its properties, syntheses of PCL, PCL composites, and PCL blends, but to provide a detailed investigation into the utility of PCL/PCL-based adsorbing agents in the removal of dyes/heavy metal ions.

Keywords: glycerin; Ni-based catalyst; lanthanum; semi-industrial scale; hydrogen production; biorefinery; monitoring.

While DNA serves as the fundamental genetic blueprint for an organism, it is not a static entity. Gene expression, the process by which genetic information is utilized to create functional products like proteins, can be modulated by a diverse range of environmental factors. Epigenetic mechanisms, encompassing DNA methylation, histone modification, and microRNAs, play a pivotal role in mediating the intricate interplay between the environment and gene expression. Intriguingly, alterations in the epigenome have the potential to be inherited across generations. Ethanol abuse poses significant health issues worldwide. Ethanol has the capability to induce changes in the epigenome, which can be inherited by offspring, thus impacting them even in the absence of direct ethanol exposure. This review article reviewed the alterations caused by ethanol on the epigenome. We thoroughly gathered all relevant papers investigating the behavioral and molecular consequences of parental ethanol exposure on their offspring. In conclusion, the comprehensive analysis of the literature supports the notion that ethanol exposure induces lasting epigenetic alterations, which can influence the behavior and health of future generations. This knowledge emphasizes the significance of addressing the potential transgenerational effects of ethanol and highlights the importance of preventive measures to minimize the adverse impact on offspring.

Governments worldwide are actively committed to achieving their carbon emission reduction targets, and one avenue under exploration is harnessing the potential of hydrogen. Blending hydrogen with natural gas is emerging as a promising strategy to reduce carbon emissions, as it burns cleanly without emitting carbon dioxide. This blending could significantly contribute to emissions reduction in both residential and commercial settings. However, a critical challenge associated with this approach is the potential for Hydrogen Embrittlement (HE), a phenomenon wherein the mechanical properties of pipe steels degrade due to the infiltration of hydrogen atoms into the metal lattice structure. This can result in sudden and sever failures when the steel is subjected to mechanical stress. To effectively implement hydrogen-natural gas blending, it is imperative to gain a comprehensive understanding of how hydrogen affects the integrity of pipe steel. This necessitates the development of robust experimental methodologies capable of monitoring the presence and impact of hydrogen within the microstructures of steel. Key techniques employed for this assessment include microscopic observation, hydrogen permeation tests, and tensile and fatigue testing. In this study, samples from two distinct types of pipeline steels used in the natural gas distribution network underwent rigorous examination. To induce hydrogen absorption, an electrochemical charging process is employed in a solution rich in H+ ions. This charging process, accomplished by a potentiostat applying a constant current, prompts the hydrogen evolution reaction at the steel specimen, acting as the cathode of the charging cell. Immediate tensile and fatigue testing following the charging process enables the evaluation of mechanical properties in comparison to non-charged samples. Different charging current densities are employed to simulate various hydrogen blend scenarios. The findings from this research indicate that charged samples exhibit a discernible decline in fatigue and tensile properties. This deterioration is attributed to embrittlement and reduced ductility stemming from the infiltration of hydrogen into the steel matrix. The extent of degradation in fatigue properties is correlated not only to the hydrogen content but also to the hydrogen permeability and diffusion rate influenced by steel’s microstructural features, with higher charging current densities indicating a more significant presence of hydrogen in the natural gas pipeline blend.

: The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating technique was employed. Pre-crystallization was achieved by annealing the films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dissolve the perovskite film. Subsequently, residual solvent was removed through spin coating. The mor-phological analysis of the perovskite film surface after recrystallization at temperatures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was confirmed by the peaks observed in the X-ray diffraction patterns.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

Introduction: Substance-induced psychotic disorder (SIPD) is a mental health condition linked to the use of a psychotropic substance whose pathogenesis has not been totally clarified. The present retrospective observational study has the objective to identify differences in clinical features and peripheral biomarkers in SIPD patients according to the main substance of abuse.Methods: A total sample of 218 patients was divided in 3 groups according to the type of consumed substance: alcohol, cannabis and psychostimulants. The 3 groups were compared for continuous variables by one-way analyses of variance (ANOVAs) and for qualitative variables by χ² tests. After removing alcohol-induced psychotic disorder group, the same analyses were repeated. Statistically significant variables from these latter analyses were included in a binary logistic regression model to confirm their reliability as predictors for cannabis- or psychostimulants-induced psychotic disorders. Results: Psychotic cannabis abusers were younger (p<0.01) and had an earlier age at onset (p<0.01). On the contrary, alcohol consumers resulted to have a longer duration of illness (p<0.01), more previous hospitalizations (p=0.04), more frequent medical comorbidity (p<0.01), higher mean Modified Sad Person Scale scores (p<0.01). Finally, psychostimulant abusers had more frequently a lifetime history of poly-substance use disorders (p<0.01). Binary logistic regression revealed that higher mean Brief Psychiatric Rating Scale scores (p<0.01) higher sodium (p=0.012) and haemoglobin(p=0.040) plasma levels were predictors of cannabis misuse in SIPD patients.Conclusions: Different clinical factors and biochemical parameters con be associated to SIPD according to the main substance of abuse, thus requiring a specific management by clinicians.

Herein, we investigated hydrogels composed of boronic Acid functionalized alginate and blended with polyvinyl alcohol of different molecular weights to control the release of metoclopramide hydrochloride (MTC) as a function of pH and shear stress. The functionalization of alginate introduced dynamic covalent bonding and pH-responsive properties that can modulate network connectivity. The study investigated the viscoelastic properties of the hydrogels, their drug release profiles, and their responsiveness to changes in pH and shear forces. The results showed higher PVA molecular weight and alkaline pH conditions increased hydrogel viscosity and stiffness due to a more stable and interconnected network structure than acidic pH. Metoclopramide release revealed that the hydrogels exhibited pH-responsive drug release behavior. The drug was more readily released under acidic conditions due to the instability of sp2-hybridized boronate ester bonds. The influence of shear forces on the release of metoclopramide was also investigated at shear rates of 1, 10, and 100 s-1, revealing their effect on matrix stiffening. The research shows that AlgBA/PVA hydrogels have unique properties, such as dynamic covalent bonding, that make them sensitive to external mechanical forces. This sensitivity makes them ideal for applications where physiological conditions trigger drug release

Polyglycerols (PGs) are biocompatible and highly functional polyols with a wide range of applications, such as emulsifiers, stabilizers, antimicrobial agents, in many industries including cosmetics, food, plastic and biomedical. The demand increase for biobased PGs encourages researchers to develop new catalytic systems for glycerol polymerization. This review focuses on alkaline homogeneous and heterogeneous catalysts. The performances of the alkaline catalysts are compared in terms of conversion and selectivity, and their respective advantages and disadvantages are commented. While homogeneous catalysts exhibit a high catalytic activity, they cannot be recycled and reused, whereas solid catalysts can be partially recycled. The key issue for heterogenous catalytic systems, which is unsolved so far, is linked to their instability due to partial dissolution in the reaction medium. Further, this paper also reviews the proposed mechanisms of glycerol polymerization over alkaline-based catalysts and discuss the various operating conditions with an impact on the performances. More particularly, temperature and amount of catalyst proved to have a significant influence on glycerol conversion and on its polymerization extent.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Transdermal alcohol biosensors have the ability to detect the alcohol that emanates from the bloodstream and diffuses through the skin. However, they have suffered from long-term fouling of the sensor element and drift in the resulting sensor readings over time. Here, we report a disposable cartridge platform that solves the problem of sensor fouling, and an enzymatic detection pathway that minimizes baseline drift for sensitive detection. Laboratory characterization of the enzymatic alcohol sensor demonstrates a linear sensor range of between 0 and 50 mM. Further, we show continuous transdermal alcohol data recorded with a human subject over 48 hours.

Abstract: Calcium-based catalysts are of a high interest for glycerol polymerization due to their high catalytic activity and large availability. However, their poor stability under reaction conditions is an issue. In the present study, we investigated the stability and catalytic activity of Ca-hydroxyapatites (HAps) as one of the most abundant Ca-source in nature. A stochiometric, a Ca-deficient and a Ca-rich HAps have been synthetized and tested as catalysts in the glycerol polymerization reaction. Deficient and stochiometric HAps exhibited a remarkable 100% selectivity to triglycerol at 15 % of glycerol conversion at 245 °C after 8 h of reaction in the presence 0.5 mol.% of catalyst. Moreover, under the same reaction conditions, Ca-rich HAp showed a high selectivity (88 %) to di- and triglycerol at a glycerol conversion of 27 %. Most importantly, these catalysts were unexpectedly stable towards leaching under the reaction conditions based on the ICP-OES results. However, based on the catalytic tests and characterization analysis performed by XRD, XPS, IR, TGA-DSC and ICP-OES, we found that HAps can be deactivated by the presence of the reaction products themselves, i.e., water and polymers.

Giant unilamellar vesicles (GUVs) are membrane model used to study membrane properties. Electroformation is one of the methods used to produce GUVs. During electroformation protocol dry lipid film is formed. Drying of the lipid film induce Cholesterol (Chol) demixing artifact, in which Chol forms anhydrous crystals, where these crystals does not participate in formation of vesicles. This leads to a lower Chol concentration in the vesicle bilayers compared to the Chol concentration in the initial lipid solution. To address this problem, we propose novel electroformation protocol that includes rapid solvent exchange, plasma cleaning and spin-coating methods to produce GUVs. We tested the protocol focusing on vesicles with high Chol content using different spin-coating durations and vesicle types deposition. Additionally, we compared the novel protocol using completely dry lipid film. The optimal spin-coating duration for vesicles made out of phosphatidylcholine/Chol mixture was 30 s. Mulitlamellar vesicles (MLVs), large unilamellar vesicles (LUVs) obtained by extrusion of MLVs through 100 nm membrane pores and LUVs obtained by extrusion of previously obtained LUVs through 50 nm membrane pores were deposited on electrode for 1.5/1 Chol/phosphatidylcholine lipid mixture and the results were compared. Electroformation using all three deposited vesicle types gave a high GUVs yield, but deposition of LUVs obtained by extrusion of MLVs through 100 nm membrane pores gave the most reproducible results. Using deposition of these LUVs, we produced GUVs with high yield for 6 different Chol concentrations (from 0 % to 71.4%). Using protocol that includes dry lipid film GUVs yield was lower and Chol demixing artifact was induced, proving that the lipid film should never undergo drying when Chol content is high.

Two important types of metal oxide nanoparticle catalysts Copper (II) oxide (CuO) and Cerium oxide (CeO₂) are prepared by a suitable method which was traditional precipitation (PT) method at calcination temperature of 400^oC for 5h and used for the synthesis of glycerol carbonate GC (C₄H₆O₄) from the direct reaction by the carbonylation of Glycerol GL (C₃H₈O₃) with Carbone Dioxide. The precipitation (PT) was an important route for the preparation of nanoparticles catalyst. The effects of performance of (CuO and CeO₂) nanoparticle catalysts on the conversion of glycerol GL, yield of glycerol carbonate GC, selectivity of glycerol carbonate are researched. XRD, XPS, BET, FT-IR, CO₂-TPD, H₂-TPR are used for the characterization of the prepared catalysts. Comparing the optimal performance between them under reaction conditions were 150 ^oC, 4MPa (40 bar.), 5h, and both CuO and CeO₂ catalyst amount 37.6 % (based on ratio of glycerol weight) by using 2-pyridinecarbonitrate (C₆H₄N₂) as dehydrating agent and dimethylformamide (DMF), (C₃H₇NO) as solvent. The glycerol conversion (X_GL), glycerol carbonate yield (Y_GC) and glycerol carbonate selectivity (S_GC) over 0.7g CuO are 57.151%, 47.524%, and 83.156%, respectively, and glycerol carbonate yield over 0.7 CeO₂ is 36.2185% or 35.076%, and the yield of GC could reach as high as 78.234% over 1.73g CeO₂, the both catalysts could be easily regenerated by washing with methanol and water after a reaction and then dried at 60 ^oC overnight after that calcination at 400 ^oC for 5h without loss of activity after five recycling times, In addition to, the (ICP- MS) results confirmed that the leaching of CuO and CeO₂ was below the detection limit.

The occurrence of bone-related disorders and diseases has increased dramatically in recent years around the world. Demineralized bone matrix (DBM) has been widely used as a bone implant due to its osteoinduction and bioactivity. However, the use of DBM is limited because it is a particulate material, which makes it difficult to manipulate and implant with precision, in addition, these particles are susceptible to migrate to other sites. To address this situation, DBM is commonly incorporated into a variety of carriers. An injectable scaffold has advantages over bone grafts or preformed scaffolds, such as the ability to flow and fill the bone defect. The aim of this research is to develop a DBM carrier with such viscoelastic properties to obtain an injectable bone substitute (IBS). The DBM carrier developed consisted of a PVA/glycerol network cross-linked with borax and reinforced with CaCO3 as a pH neutralizer, porosity generator, and source of Ca. The physicochemical properties were determined by the injectability test, FTIR, SEM, and TGA. Porosity, degradation, bioactivity, possible cytotoxic effect, and proliferation in osteoblasts were also determined. The results show that the developed material has great potential to be used in bone tissue regeneration

The study was conducted to prepare juice blend by using Orange, Carrot and Tiger-nut juices. Fully mature raw Orange, Tiger-nut and Carrot were processed into juice forms and combined in different ratios which were analyzed for their composition and Consumer’s acceptability. The analysis showed that the juice with higher Orange juice content had higher levels of acidity. This implies that they would last longer as they are not susceptible to spoilage by most organisms. The Juice with higher orange juice content was also found to be very rich in Vitamin C, due to inherent high amount of Vitamin C in raw Orange Fruit. However, it scored lowest in terms of general acceptability because the raw fruit was purchased separately and there’s a likelihood some of the Orange used in the Juice preparation were sour. This led to a sour taste in this Juice blend. The Juice blend that contained equal proportions of all three juices was the most acceptable to the consumers in terms of color, taste and Nutritional composition. It gave equal amounts of the unique properties of each fruit and provided a unique color and taste that was very appealing to the panelists. This product makes it possible to properly utilize these fruits, reduce post harvest losses, cater to different health needs of the consumers and ensure food security. It is recommended that further work should be done on antioxidant properties, other fruit blends and storage stability of the beverage to determine the shelf-life.

A novel hybrid material based on Polyvinyl alcohol-Chitosan (PVA-Cs) was made, reinforced with conductive polymer fillers such as polypyrrole (PPy), Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS), carbon black (CB) and multi-wall carbon nanotubes (MW CNT). Our proposal is to use these fillers, which have not been studied in this context before, for obtaining composite materials, and to characterize them for the development of applications in microelectronics. FTIR analysis made evident the different func-tional groups present in the matrix and the fillers used. The use of quaternary mixtures (4 fillers) increased the contact angle, which increased the degree of hydrophobicity of the biocomposite. The Nyquist diagram of the analyzed samples showed a decrease in resistance and energy diffu-sion; the latter due to the transfer of electrons caused by the conductive polymers CB and the MWCNT. In the mechanical tension tests, Young's modulus values of 18.386 MPa were obtained, in contrast with the material matrix of PVA-Cs, which showed values of 11.628 MPa. Further-more, morphological analysis by SEM showed that the materials obtained were homogeneous, with no phase formation. The materials obtained showed higher electrical conductivity in the presence of the OH and NH2 groups, which could have possible applications in biopolymer elec-trodes.

This study investigates the cyclic load application impact on fly ash-based geopolymer composites that are reinforced with a low amount of fibre reinforcement. For reinforcement purposes, PVA and steel fibres are used. For testing purposes, four geopolymer composite mixes were made, 3 of which had fibre reinforcement. Simultaneously specimens were tested for shrinkage, static load-induced creep, and cyclic load-induced creep. For static and cyclic creep testing, specimens were loaded with 20% of their strength. For cyclic creep testing, load application and release cycles were seven days long. When each cycle was introduced, the load was added in steps. In 5 minutes, by 25% steps of the necessary load, the specimens were loaded or unloaded. Only plain specimens show that static creep strains are within cyclic creep strains. For all the other specimens, the static load is higher than the cyclic load-induced creep amplitude. Also, 1% PVA fibre-reinforced specimens show the most elastic characteristics under cyclic load, and 1% steel fibre-reinforced specimens appear to be the most resistant to the cyclic load introduction.

The surface characterization of indium tin oxide (ITO) films was processed by oxygen (O2) plasma gas using a magnetron sputtering method of varying O2-plasma gas from 20 sccm to 100 sccm for potentially fostering in electronic devices applications on dye-sensitize solar cells (DSSC) in this work. In order to gain an outstanding performance rate with high-quality thin films, the affect of correlation between the electrical, optical, and morphology properties was significantly investigated. Clearly, the content of investigation exhibited that the films properties was changed by variation of the gas composition. These changes have contemporary relevance to the sputtering gas during the deposition process. To conclude, the greatest electrical properties was displayed by O2 -plasma gas flow rate of 20 sccm, which showed the lowest resistivity. In addition to this, the final products were practically fabricated to active layers for dye-sensitize solar cells (DSSC) applications. The highest efficiency of DSSC device was indicated of approximately 0.35% which was located by 40 sccm of the O2-plasma gas. Consequently, the study could be a possibility way of preparing ITO thin films with improved special properties of substantial applications for solar cells devices in the near future.

The production of biodiesel through transesterification routes generates large amounts of glycerol, approximately 10 m3 for every 90 m3 of the biodiesel produced. Taking into account this scenario, the valorization of glycerol using chemical routes that could be operated in biodiesel industry constitutes a promising approach to achieve added-value products. An interesting option is the production of ethers, which can be used as fuel additives in diesel engines to improve the combustion efficiency, reducing soot emission and increasing cetane index. In this study, a purification route was applied to crude glycerol and its valorization by etherification was evaluated. The glycerol contents of purified samples were above 98% wt. The purified and commercial glycerol was used to obtain ethers. Etherification reactions were carried out with different alcohols (ethanol, isopropanol and 3-methyl-1-butanol) into a batch reactor, using small amount of Amberlyst 15 as a catalyst, at autogenous pressure and solvent-free conditions. The glycerol conversion, selectivity and yield to ethers were evaluated. A glycerol conversion of 97% wt. with selectivity of 80% to monoether was obtained when using ethanol. For isopropanol, the glycerol conversion was up to 95% (76% of monoether and 22% of diether). However, the selectivity to ethers for 3-methyl-1-butanol was negligible (&lt;3% wt.). A process simulation for purification and etherification steps integrated with a biodiesel production was assessed in terms of productivity and energy consumption, considering different scenarios of glycerol/alcohol molar ratios.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

Fetal Alcohol Spectrum Disorders (FASD) represent a continuum of lifelong impairments resulting from prenatal exposure to alcohol, with significant global impact. The “spectrum” of disorders includes a continuum of physical, cognitive, behavioral, and developmental impairments, which can have profound and lasting effects on individuals throughout their lives impacting their health, social interactions, psychological well-being and every aspect of their lives. This narrative paper explores the intricate relationship between oxidative stress and epigenetics in FASD pathogenesis and its therapeutic implications. Oxidative stress, induced by alcohol metabolism, disrupts cellular components, particularly in the vulnerable fetal brain, leading to aberrant development. Furthermore, oxidative stress is implicated in epigenetic changes, including alterations in DNA methylation, histone modifications, and microRNA expression, which influence gene regulation in FASD patients. Moreover, mitochondrial dysfunction and neuroinflammation contribute to epigenetic changes associated with FASD. Understanding these mechanisms holds promise for targeted therapeutic interventions. This includes antioxidant supplementation and lifestyle modifications to mitigate FASD-related impairments. While preclinical studies show promise, further clinical trials are needed to validate these interventions' efficacy in improving clinical outcomes for individuals affected by FASD. This comprehensive understanding of the role of oxidative stress on epigenetics in FASD underscores the importance of multidisciplinary approaches for diagnosis, management, and prevention strategies. Continued research in this field is crucial for advancing our knowledge and developing effective interventions to address this significant public health concern.

This study presents, for the first time, the development of fibers with favorable properties for biodegradable wound dressings made from the Ecovio® (EC) polymer blend, composed of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT), incorporated with tea tree essential oil (TTE). TTE presented antimicrobial activity against Pseudomonas aeruginosa and Staphylococcus aureus, achieving minimal inhibitory concentrations of 15 and 7.5 mg/mL, respectively. The TTE was mixed with EC in a binary chloroform and formic acid (85/15 v/v) mixture, leading to homogeneous and wettable fibers by electrospinning. The EC/TTE fibers were characterized confirming the TTE in the fibers. The tests showed that TTE (0.5, 1.0 or 1.5 mL) improved the polymer blend electrospinnability. TTE (1.5 mL or 75 w% concerning the EC) lead to homogeneous fibers with an average diameter of 278 nm. TTE (75 w%) increased the wettability of the EC fibers from 120±2° to 69±1°. Preliminary bacterial adhesion and proliferation assays demonstrated that the EC/TTE fibers have anti-adhesive activity e seems to be more toxic against P. aeruginosa compared to S. aureus after 24 hours of incubation. Compatibility tests with human blood indicated that the EC/TTE fibers accelerate blood coagulation. The EC/TTE fibers exhibit promising chemical and biological properties (in vitro) for the development of wound dressings.

Given the high levels of overall volume of alcohol use, detrimental drinking patterns, and high levels of alcohol-attributable mortality and burden of disease, Lithuania implemented a series of alcohol control policies within a relatively short period of time (2008 to 2019). Based on their expected impact on alcohol consumption and alcohol-attributable harm, as well as their target population, the respective policies were classified using a set of objective criteria and expert opin-ion. The classification criteria included: positive vs. negative outcomes, mainly immediate versus delayed outcomes, and general population versus specific group outcomes. The judgement of the alcohol policy experts converged on the objective criteria, and, as a result, two tiers of inter-vention were identified: Tier 1 – general population interventions with an anticipated immediate impact; Tier 2 – other interventions aimed at the general population. In addition, interventions for specific populations were identified. This adaptable methodological approach to alcohol control policy classification is intended to provide guidance and support the evaluation of alcohol policies elsewhere, lay the foundation for the critical assessment of the respective policies to im-prove health and increase life expectancy, and to reduce crime and violence.

CMC/PVA composite nanofiber membrane was prepared by electrostatic spinning method, using carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) as raw materials and glutaraldehyde as cross-linking agent. The structure, morphology, thermal stability, and filtration performance of CMC/PVA nanofiber membranes were characterized by advanced instrumental analysis methods such as scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, ultraviolet analysis and energy spectrum analysis. The results show that the average fiber diameter decreases from 381 nm to 183 nm, when the spinning voltage is 23 KV and the jet speed is 2 µL/min. The obtained fiber has the smallest particle size and the most uniform distribution. Infrared spectroscopy analysis confirms that the adsorption behavior of nanofiber membranes on Cu2+ and Cr6+ is chemical adsorption. The retention rates of CMC/PVA nanofiber membranes for Cu2+ and Cr6+ reached 97% and 98%, respectively.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

In order to assess the human exposure risks from the release of contaminants from water pipes made of polyvinyl chloride (PVC), experiments were carried out by subjecting the PVC pipe material to burning and leaching conditions followed by analysis of the emission and leachate samples. The emissions of burning pipes were analyzed by both infrared spectrometry and gas chromatography-mass spectrometry (GC-MS). The emission results indicate the presence of chlorinated components including chlorine dioxide, methyl chloride, methylene chloride, allyl chloride, vinyl chloride, ethyl chloride, 1-chlorobutane, tetrachloroethylene, chlorobenzene, and hydrogen chloride were detected in the emissions of burning PVC pipes. Furthermore, the concentrations of benzene, 1,3-butadiene, methyl methacrylate, carbon monoxide, acrolein, and formaldehyde were found at levels capable of affecting human health adversely. The analysis of PVC pipe leachates using GC-MS shows that there are 40-60 tentatively identified compounds, mostly long-chain hydrocarbons such as tetradecane, hexadecane, octadecane, and docosane, were released when the burned PVC materials were soaked in deionized water for one week. Quantitative analysis shows that 2-butoxyethanol, 2-ethyl-1-hexanol, and diethyl phthalate were found in the burned PVC polymer at the average levels of 2.7, 14.0, and 3.1 micrograms per gram (g/g) of pipe material. This study has significant implications for understanding the benzene contamination of drinking water in the aftermath of wildfires that burned polymer pipes in California.

Climate change, increasing global food needs, and decreasing global resources brought a new era to human every-day live with a strong turn to circular economy and sustainability. Food packaging and preservation is an important global sector where enchanced research is carried out. New methods such as active packaging and chemical preservatives replacement are of major interest. Many researchers were published studies about active packaging films, replacement of chemical preservatives with natural originated extracts, and novel incorporation procedures. Sequentially to our and other scientists’ previous work, in this paper we present the results of the improvement which was achieved by incorporating the developed nanohybrid of natural-halloysite/carvacrol-extract, the pure natural carvacrol extract and the commonly used low-density-polyethylene. The well known corona-treatment procedure was employed to produced the optimum final film and the results shown that the low-density-polyethylene incorporated with natural-halloysite/carvacrol-extract nanohybrid and coated external with extra carvacrol extract exhibited aproximatelly 100% higher Young-Modulus values, slightly decreased ultimate strength by 20%, and almost stable elonation at break properties. The water-vapor and oxygen barrier increased by 40%. Finally, the antioxidant activity of the corrona-treated film increased by 28% compared to the similar but untreated product because of the lower release rate of the carvacrol.

Polyvinyl alcohol-engineering cementitious composites (PVA-ECC) has been widely applied in bridge deck repairing or widening, the common practice for doing this is that a portion of a bridge is left open to traffic while the closed portion is constructed, which expose the early age PVA-ECC to the vehicle-induced vibrations. However, whether vehicle-induced vibrations affect the tensile performance of early age PVA-ECC remains unknow. The purpose of this study was to conduct laboratory test programs on how much vehicle-induced vibrations during early ages affected the tensile performance of PVA-ECC. A self-improved device was used to simulate the vehicle-induced vibrations, and after vibrating with the designed variables, both a uniaxial tensile test and a grey correlation analysis were performed. The results indicated that: the effects of vehicle-induced vibrations on the tensile performance of early age PVA-ECC were significant, and they generally tended to be negative in this investigation. In particular, for all of the vibrated PVA-ECC specimens, the most negative age when vibrated occurred during the period between the initial set and the final set. We concluded that although vehicle-induced vibrations during the setting periods had no substantial effects on the inherent strain-hardening characteristics of PVA-ECC, the effects should not be ignored.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Rigid polyurethane foams were synthesized using a renewable polyol from the simple physical mixture of castor oil and crude glycerol. The effect of the catalyst and blowing agent in the foams properties was evaluated. The use of physical blowing agent (cyclopentane and n-pentane) allowed obtaining foams with smaller cells in comparison with the foams produced with a chemical blowing agent (water). The increase of water content caused a decrease of density, thermal conductivity, compressive strength and Young's modulus, which indicates that the increment of CO₂ production contributes to the formation of larger cells. Higher amount of catalyst in the foam formulations caused a slight density decrease and an increase small significance of thermal conductivity, compressive strength and Young's modulus values. These green foams presented properties that indicate a great potential to be used as thermal insulation, as density (23 - 41 kg m^-3), thermal conductivity (0.0128 – 0.0207 W m^-1 K^-1), compressive strength (45 - 188 kPa) and Young's modulus (3 - 28 kPa). These biofoams are also environmental friendly alternatives and can aggregate revenue to biodiesel industry, contributing for reduction of this fuel prices.

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

Objective: To provide mechanistic evidence for the epidemiological link between long-term use of alcohol containing mouthwashes and oral cancer.Methods: Human epithelial keratinocytes were exposed for 30 seconds to concentrations of ethanol commonly present in mouthwashes. After a recovery period, cell viability was assessed with the MTT assay.Results: A marked cytotoxic effect was observed for ethanol concentrations of 20% and above. Conclusions: The cytotoxicity of ethanol can explain the epidemiological association between mouthwash use and oral cancer. Recent findings indicate that the risk of developing cancer in a tissue is strongly determined by the number of stem cell divisions accumulated by the tissue during a person's lifetime; cell division is a major source of mutations and other cancer-promoting errors. Since cell death activates the division of stem cells, the cytotoxicity of ethanol on the cells lining the oral mucosa will promote the division of the stem cells located in deeper layers to produce new cells to regenerate the damaged epithelium. If we regularly use mouthwashes containing cytotoxic concentrations of ethanol, we will force the stem cells of the oral cavity to divide more often than usual and our risk of developing oral cancer will probably increase.Clinical significance: Many mouthwashes contain percentages of ethanol above 20%. Because ethanol is not crucial to prevent and reduce gingivitis and plaque, members of the dental team should consider the potential risk of oral cancer associated with frequent use of alcohol containing mouthwashes when advising their patients.

Glycerol is a subproduct of biodiesel production and represents an important problem when generated in large scale. Alternatives that can utilize this unrefined byproduct is of potential interest. It is herein described the synthesis of a series of 1,2,3-triazoles using glycerol as starting material. The key step involved in the preparation of triazolic derivatives corresponded to the Copper(I)-catalyzed Azide-Alkyne Cycloaddition (CuAAC), also known as click reaction, between 4-(azidomethyl)-2,2-dimethyl-1,3-dioxolane (3) and different terminal alkynes. The eight prepared derivatives were evaluated with regard to their fungicide, phytotoxic and cytotoxic activities. The fungicide activity was assessed in vitro against Colletotrichum gloeosporioides, the causing agent of papaya anthracnose. It was found that the compounds 1-(1-((2,2-dimethyl-1,3-dioxolan-4-yl)methyl)-1H-1,2,3-triazol-4-yl)cyclohexanol (4g) and 2-(1-((2,2-dimethyl-1,3-dioxolan-4-yl)methyl)-1H-1,2,3-triazol-4-yl)propan-2-ol (4h) demonstrated high efficiency on controlling C. gloeosporioides when compared to the commercial fungicide tebuconazole. The triazoles did not present any phytotoxic effect when evaluated against Lactuca sativa. However, five derivatives were mitodepressive, inducing cell death detected by the presence of condensed nuclei and acted as aneugenic agents in the cell cycle of L. sativa. It is believed that glycerol derivatives bearing 1,2,3-triazole functionalities may represent a scaffold to be explored toward the development of new agents to control C. gloeosporioides.

This study introduces a novel nanocomposite coating composed of PANI/CeO2 nanocomposite films, aimed at addressing corrosion protection needs. Analysis through FTIR spectra and XRD patterns confirms the successful formation of the nanocomposite films. Notably, the PANI/CeO2 nanocomposite films exhibit a hydrophilic nature. The bandgap energy of the PANI composite film measures at 3.74 eV, while the introduction of CeO2 NPs into the PANI matrix reduces the bandgap energy to 3.67 eV. Furthermore, the electrical conductivity of the PANI composite film is observed to be 0.40 S.cm-1, with the incorporation of CeO2 NPs leading to an increase in electrical conductivity to 1.07 S.cm-1. To evaluate its efficacy, electrochemical measurements were conducted to assess the corrosion protection performance. Results indicate a high protection efficiency of 92.25% for the PANI/CeO2 nanocomposite film.

Stress during a pandemic increased the risk of alcohol consumption, which may require pharmacological management. The characteristics of emergency calls for alcohol-related issues for patients pharmacologically treated, admitted to, or not admitted to the emergency department (ED) were analyzed. An observational single-center retrospective study was conducted from January 1, 2018 to December 31, 2021, and divided into 2-year periods (2018–2019 and 2020–2021). This study focused on calls to one of the EDs of seven hospitals in the Bari (Italy) metropolitan area for patients requiring emergency services (ES) who were either admitted or not admitted, due to their refusal. A 30% reduction in emergency calls for alcohol-related issues and a 41.17% reduction in calls for patients who refused to be admitted to the ED were observed during the pandemic. During the pandemic, a reduced rate of pharmacological treatment for calls coded green (non-critical), and an increase in calls coded yellow (fairly critical) and red (very critical) were recorded. Metadoxine was administered in almost all alcohol-related emergencies, primarily in conjunction with drugs acting on the gastrointestinal tract, irrespective of age, the period considered, and whether patients were admitted or not admitted to the ED. ES is the first and only out-of-hospital service encountered by numerous patients with alcohol-use disorders who refuse to be admitted to the ED. These patients should be directed by ES personnel to a multidisciplinary program to receive treatment for drinking, improve their quality of life, and reduce sanitation costs.

We investigated the structural evolution of the two-phase blends of polycarbonate (PC) and poly(methyl methacrylate) (PMMA) at various blend compositions by simultaneous biaxial stretching using optical microscopy and SEM observation. The spherical PMMA domains and PC matrix in 30/70 PC/PMMA were enlarged uniformly at all in-plane direction, while the anisotropic-shaped co-continuous structure in 50/50 PC/PMMA was deformed to crosshatched one by in-plane bimodal orientation. In 70/30 PC/PMMA, the phase inversion was found to occur by simultaneous biaxial stretching; i.e., the spherical PMMA domains were changed to crosshatched matrix by in-plane bimodal orientation due to coalescence of the PMMA domains during the stretching. Owing to the phase inversion, the surface hardness estimated by pencil hardness test became harder from 2B to 2H with increasing the strain from 1.0 to 2.0.

Background: This study, conducted in October 2017 at two Canadian universities, aimed to explore the relationships between gender expression, protective coping strategies, alcohol saliency, and high-risk alcohol use. Methods: Validated scales were employed to assess these variables using survey data. Multivariate analyses were conducted to investigate the associations between these factors and high-risk drinking. Results: The study revealed significant associations between high-risk drinking and androgynous gender roles (OR=1.58, 95% CI: 1.19-2.10) as well as among self-reported males (OR=2.21; 95% CI: 1.77-2.75). Additionally, protective behavioral strategies were inversely related to high-risk drinking (OR=0.95; 95% CI: 0.94-0.96), while higher alcohol saliency exhibited a positive correlation with high-risk drinking (OR=1.12; 95% CI: 1.11-1.14). Conclusions: These findings underscore the importance of considering gender, alcohol saliency beliefs, and protective behavioral strategies in the development and refinement of interventions aimed at reducing high-risk alcohol use on Canadian campuses.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

Apathy is a fundamental neuropsychiatric symptom of Korsakoff’s syndrome (KS) and has also been reported in patients with alcohol use disorder with no (AUD) or less severe cognitive disorders (ALC). However, research on the nature of apathy is limited in these groups. Aim of this study was to examine the multidimensional nature of apathy in patients with KS, ALC and AUD. Moreover, we examined differences between apathy ratings by patients and their professional caregivers, and related apathy to everyday functioning and overall cognition. Twenty-four patients with KS, 24 patients with ALC and 21 patients with AUD participated in this study. Apathy was measured using the Apathy Motivation Index (AMI), which distinguishes behavioral, emotional and social apathy. Both patients and professional caregivers reported social apathy as most prominent symptom, compared to behavioral and emotional apathy. Apathy ratings did not differ across the three patient groups. Discrepancies between patient and caregiver ratings were observed in patients with KS and ALC, with more severe apathy reported by caregivers. Caregiver-reported behavioral and social, but not emotional, apathy was related to everyday functioning. These results show that apathy is present in a substantial proportion of patients with alcohol addiction with or without cognitive impairments.

Increased motivation towards alcohol use and suboptimal behavioural control are suggested to predispose adolescents to Alcohol Use Disorders (AUDs). Paradoxically however, most adolescent AUDs resolve over time without any formal intervention, suggesting adolescent resilience to AUDs. Importantly, studies directly comparing adolescent and adult alcohol use are largely missing. We therefore aimed to unravel the moderating role of age in the relation between alcohol use and motivational and control-related cognitive processes in 45 adolescent drinkers compared to 45 adults. The results showed that enhancement drinking motives and impulsivity related positively to alcohol use. Although enhancement drinking motives and impulsivity were higher in adolescents, the strength of the relation between these measures and alcohol use did not differ between age groups. None of the alcohol use-related motivational measures (i.e., craving, attentional bias, approach bias) and behavioral control measures (i.e., interference control, risky decision making, working-memory) were associated with alcohol use or differed between age groups. These findings support the role of impulsivity and affective sensitivity in adolescent drinking, but question the moderating role of age therein. The current study contributes towards understanding the role of age in the relation between alcohol use and cognition.

Introduction: Liver cirrhosis develops in about 10% of alcohol abusers. To date, a number of cells and cytokines have been identified, which are involved in induction of liver fibrotic processes. Nevertheless, the pathogenesis of liver cirrhosis has not been fully elucidated. The aim of the present study was to determine serum concentrations of afamin and adropin in patients with alcoholic liver cirrhosis and to define their correlation with the stage of disease. Materials and methods: The study included 99 patients with alcoholic cirrhosis from the region of Lublin, (Eastern Poland). Liver cirrhosis was diagnosed based on clinical features, history of heavy alcohol consumption, laboratory tests and abdominal ultrasonography. The control group consisted of 20 healthy individuals without liver disease who did not abuse alcohol. The serum afamin and adropin concentrations were determined using ELISA kits. Results: The concentration of afamin was found to be significantly lower in patients with compensated alcoholic liver cirrhosis, i.e. P-Ch B (85.1±40.6 μg/ml) and P-Ch C (56.4±32.3 μg/ml) individuals, as compared to the control group (135.9±43.6 μg/ml); p-value was <0.01 and <0.001, respectively. As far as adropin is concerned, a reverse relationship was demonstrated: the highest concentration was found in patients with P-Ch C (11.7±5.7 ng/ml) cirrhosis. Furthermore, the above concentration was significantly higher compared to patients with P-Ch A cirrhosis (7.2±2.8 ng/ml; p<0.05) and controls (7.5±2.6 ng/ml; p<0.05). Conclusions: The concentration of afamin decreases with the severity of alcoholic liver cirrhosis, which most likely results from impaired hepatic synthesis. Otherwise, the higher the stage of disease according to the Child-Pugh score, the higher the concentration of adropin.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

Pancreatic cancer is one of the most fatal common cancers affecting both men and women, representing about 3 percent of all new cancer cases in the United States. In this study, we aimed to investigate the association of pancreatic cancer risk with alcohol consumption as well as folate intake. We performed a case-control study of 384 patients diagnosed with pancreatic cancer from May 2004 to December 2009 and 983 primary care healthy controls. Our findings showed no significant association between risk of pancreatic cancer and either overall alcohol consumption or type of alcohol consumed (drinks/day). Our study showed dietary folate intake was modestly but significantly inversely associated with pancreatic cancer (OR=0.99, P <.0001). The current study supports the hypothesis that pancreatic cancer risk is reduced with higher food-based folate intake.