The most commonly used real-time augmentation services in China are International GNSS Service (IGS) real-time service, PPP-B2b service, and BeiDou Satellite-Based Augmentation System (BDSBAS) dual-frequency augmentation service. However, the research on the performance evaluation, comparison and application scope of these three products is still unknown and unrevealed. This article introduces methods for obtaining real-time augmentation information and real-time orbit and clock offset recovery. Based on real-time orbit and clock offset accuracy, positioning accuracy, and positioning availability, it systematically evaluates the performance of CNES, PPP-B2b, and BDSBAS augmentation information. The results indicate that the radial accuracy of CNES and PPP-B2b real-time orbit products is consistent, and the Root Mean Square (RMS) is better than 5 cm. CNES can achieve centimeter-level accuracy in both along-track and cross-track components, surpassing the decimeter-level accuracy of PPP-B2b. Both services demonstrate consistent accuracy in real-time clock offset, with PPP-B2b showing similar standard deviations (STD) of 0.16 ns for different satellites. However, for CNES, the STD of real-time clock offset varies for GPS, BDS-3 MEO, and BDS-3 IGSO satellites, with values of 0.10 ns, 0.19 ns, and 0.60 ns, respectively. The accuracy and availability of the two PPP services exhibit the same levels, with centimeter-level accuracy achieved after convergence and positioning availability exceeding 99%. Therefore, the difference between the two services in application areas depends on the acquisition of augmentation information. However, BDSBAS, which concentrates on code observations, demonstrates lower accuracy in real-time orbit and clock offset, positioning accuracy, and positioning availability compared to the other two services. Its primary application is in the aviation and maritime domains, where there is a greater need for service integrity, continuity, and reliability.

The domain of construction engineering and management is evolving rapidly. Optimizing resource positioning is crucial for meeting the challenges of efficiency and productivity. This research presents a novel methodology that incorporates Agent-Based Modeling (ABM), Building Information Modeling (BIM), and Bluetooth Low Energy (BLE) technologies, augmented with a Client Early Warning System (CEWS) and a Decision Support System (DSS). What makes this study unique is that it provides a real-time methodology for resource allocation and project management, tailored to address the complexities of modern construction projects. The application of this integrated technological framework marks a significant leap in construction management, empowering data-driven decision-making and significantly improving project efficiency. Empirically validated through a case study at Helwan University's College of Engineering and substantiated by expert surveys, this research showcases a transformative model for resource management. The findings not only underscore the practical applicability of this approach but also open new horizons for its adoption in global construction practices, offering insights for future research endeavors focused on expanding these methodologies to a wider range of resources.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

Crop phenotyping data collection is the basis for precision agriculture and smart decisionmaking applications. In this study, a dynamic slicing and reconstruction canopy volume (DR) algorithm is proposed to accurately estimate citrus canopy volume. The algorithm dynamically slices nearby slices based on their proportional area change and density difference, subsequently conducting AS reconstruction and volume calculation for each slice using an iterative mean point spacing as the α-value. Compared with six point cloud-based reconstruction algorithms, the DR approach achieved the best results in removing perforations and lacunae (0.84) and exhibited volumetric consistency (1.53) that closely aligned with the growth pattern of citrus trees. The DR algorithm effectively addresses the challenges of adapting the thickness and number of canopy point cloud slices to the shape and size of the canopy in the ASBS and CHBS algorithms, as well as overcoming inaccuracies and incompleteness in reconstructed canopy models caused by limitations in capturing detailed features using the PCH algorithm. It offers improved adaptive ability, finer volume computations, better noise reduction, and anomaly removal. In conclusion, we recommend selecting appropriate operating environments for each algorithm based on their principles, geometric properties, volumetric values, running time, and linear relationships with one another to guide orchard mechanization and intelligent operation.

Rice, as a staple crop feeding billions, faces constant threats from various diseases jeopardizing global food security. Precise understanding of disease resistance mechanisms is crucial for developing resilient rice varieties. Traditional genetic mapping methods, such as QTL mapping, provide valuable insights into the genetic basis of diseases. However, the complex nature of rice diseases demands a holistic approach to gain accurate knowledge of it. Omics technologies, including genomics, transcriptomics, proteomics, and metabolomics, enable a comprehensive analysis of biological molecules, uncovering intricate molecular interactions within the rice plant. Integration of various mapping techniques using multi-omics data has revolutionized our understanding of rice disease resistance. By overlaying genetic maps with high-throughput omics datasets, researchers can pinpoint specific genes, proteins, or metabolites associated with disease resistance. This integration enhances the precision of disease-related biomarkers with better understanding of their functional roles in disease resistance. Improvement of rice breeding for disease resistance through this integration represents a significant stride in agricultural science because better understanding of the molecular intricacies and interactions underlying disease resistance architecture leads to more precise and efficient development of resilient and productive rice varieties. In this review, we explore how the integration of mapping and omics data can give a transformative impact on rice breeding for enhancing disease resistance.

The Range–Doppler (R-D) model is extensively employed for the geometric processing of Synthetic Aperture Radar (SAR) images. Refining the sensor motion state and imaging parameters is the most common method for achieving high-precision geometric processing using the R-D model, comprising a process that involves numerous parameters and complex computations. In this study, we introduce a novel approach to improve the positioning accuracy of the R-D model, implementing a low-order polynomial to compensate for the original imaging errors without altering the initial positioning parameters. We also design low-order polynomial compensation models with different parameters. The models are evaluated on various SAR images from different platforms and bands, including spaceborne TerraSAR-X and GF3-C images, manned airborne SAR-X images, and unmanned aerial vehicle-mounted miniSAR-Ku images. Furthermore, image positioning experiments involving the use of different polynomial compensation models and various numbers and distributions of Ground Control Points (GCPs) are conducted. The experimental results demonstrate that geometric processing accuracy comparable to that of the classical rigorous positioning method can be achieved even when applying only an affine transformation model to the images. Compared to classical refinement models, however, the proposed image-compensated R-D model is much simpler and easy to implement. Thus, this study provides a convenient, robust, and widely applicable method for the geometric positioning processing of SAR images, offering a potential approach for the joint-positioning processing of multi-source SAR images.

Positioning based on wireless signals such as mobile communication networks has become an important means to provide high-precision location services in environments where satellite signals are blocked. In complex environments such as indoor and underground, wireless signal propagation is obstructed and non-line-of-sight (NLOS) phenomena appears due to serious occlusion and reflection. The time delay caused by NLOS effects has little impact on communication system but can significantly increase positioning errors in positioning systems. Therefore, effective suppression of NLOS errors is crucial to improving 5G positioning accuracy. To address the insufficient feature extraction of existing NLOS error suppression methods, the neglect of residual NLOS measurement errors, and poor stability of position estimation results, this paper innovatively proposes a NLOS mitigation and location estimation method for 5G positioning terminals. Simulation and experimental test results demonstrate that the proposed method outperforms the comparative methods both theoretically and practically, achieving an average positioning accuracy of 1.85 meters in complex indoor NLOS environments. The method proposed in this paper provides a new strategy for NLOS error suppression in indoor 5G positioning, which can significantly contribute to high-precision location services based on commercial 5G networks.

Protection suit is vital for fireman’ safety. Traditional protection suit just physically protects fireman from empyrosis, but can not locate the body injury position from the impact debris. Herein, we present a wearable impact debris positioning system for fireman protection suit alarming based on accelerometer array. The wearable piezoelectric accelerometers with distribute regularly on the suit to detect the vibration on different body parts, which is conducive to positioning injured body parts. In addition, the injured parts can be displayed on the dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11ms attributing to smart signal processing method. This work provides a reliable and smart method for locating and assessing the body injury position from the impact debris, which is significant for fire disaster commander to rescue injured fireman in time.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

The prevalence of hepatitis B and delta viruses (HBV/HDV) among people who use drugs (PWUD) remains largely unknown. In the context of one Philadelphia-based harm reduction organization (HRO), this study aimed to assess HBV/HDV prevalence and facilitate linkage to care. Participants completed a demographic HBV/HDV risk factor survey and were screened for HBV and reflexively for HDV if positive for HBV surface antigen or isolated core antibody. Fisher’s exact tests and regression were used to understand relationships between risks and HBV blood markers. Of the 498 participants, 126 (25.3%) were susceptible to HBV, 52.6% had been vaccinated against HBV, and 17.9% had recovered from a past infection. Eleven (2.2%) participants tested positive for isolated HBV core antibody, 10 (2.0%) for HBV surface antigen, and one (0.2%) for HDV antibody. History of incarceration was associated with current HBV infection, while transactional sex and experience of homelessness were predictive of previous exposure. This study found high rates of current and past HBV infection, and a 10% HBV/HDV co-infection rate. Despite availability of vaccine, one quarter of participants remained vulnerable to infection. Findings demonstrate the need to improve low-threshold HBV/HDV screening, vaccination, and linkage to care among PWUD. The study also identified gaps in the HBV/HDV care cascade, including lack of point-of-care diagnostics and lack of support for HROs to provide HBV services.

Antifragility, a concept pioneered by Nassim Nicholas Taleb, has undergone significant development over the past decades. In his work, Taleb describes antifragility as the opposite of fragility—a system that not only withstands stress and volatility but actually thrives and improves as a result. However, many existing systems, including those in Information Technology (IT) and complex economic models, tend to fail under stress. This paper aims to explore the potential implementation of antifragility principles into software architecture. By embracing the concept of an- tifragility, software systems could be designed to not only withstand stressors but also harness them to enhance their robustness and performance. The authors recognize that traditional approaches to software architecture often focus on minimizing failure points and ensuring stability. While these approaches are valuable, they often neglect the dynamic nature of real-world systems and fail to adapt to unforeseen challenges. The paper proposes an alternative perspective that considers stress as an opportunity for improvement. By introducing antifragile elements into software architec- ture, such as decentralized decision-making, self-healing mechanisms, and adaptive resource allocation, the authors argue that software systems can become more resilient, responsive, and capable of capitalizing on stress-induced dis- ruptions. To validate their ideas, the authors present case studies and practical examples of how antifragile software architectures could operate in various domains. They also discuss potential challenges and trade-offs associated with implementing antifragility, such as increased complexity and resource requirements. By shedding light on the possi- bility of embracing antifragility in software architecture, this paper seeks to inspire further research and innovation in creating more adaptive and robust software systems that thrive in the face of stress and uncertainty.

We present a modified version of the Szilard Engine, demonstrating that an explicit measurement procedure is entirely unnecessary for its operation. By considering our modified engine, we are able to provide a new interpretation of Landauer’s original argument for the cost of erasure. From this view, we demonstrate that a reset operation is strictly impossible in a dynamical system with only conservative forces. Then, we prove that to approach a reset yields an unavoidable instability at the reset point. Finally, we present an original proof of Landauer’s principle that is completely independent from the Second Law of Thermodynamics.

Why do neurons communicate through spikes? By definition, spikes are all-or-none neural events which occur at continuous times. In other words, spikes are on one side binary, existing or not without further details, and on the other can occur at any asynchronous time, without the need for a centralized clock. This stands in stark contrast to the analog representation of values and the discretized timing classically used in digital processing and at the base of modern-day neural networks. As neural systems almost systematically use this so-called event-based representation in the living world, a better understanding of this phenomenon remains a fundamental challenge in neurobiology in order to better interpret the profusion of recorded data. With the growing need for intelligent embedded systems, it also emerges as a new computing paradigm to enable the efficient operation of a new class of sensors and event-based computers, called neuromorphic, which could enable significant gains in computation time and energy consumption — a major societal issue in the era of the digital economy and global warming. In this review paper, we provide evidence from biology, theory and engineering that the precise timing of spikes plays a crucial role in our understanding of the efficiency of neural networks.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

Spatial light modulators (SLMs) have been widely used to achieve dynamic control of optical traps. Often, holographic optical tweezers have been presumed to provide nanometer or sub-nanometer positioning accuracy. It is known that some features concerning the digitalized structure of SLMs cause a loss in steering efficiency of the optical trap, but their effect on trap positioning accuracy has been scarcely analyzed. On the one hand, the SLM look-up-table, which we found to depend on laser power, produces positioning deviations when the trap is moved at the micron scale. On the other hand, phase quantization, which makes linear phase gratings become phase staircase profiles, leads to unexpected local errors in the steering angle. We have tracked optically-trapped microspheres with sub-nanometer accuracy to study the effects on trap positioning, which can be as high as 2 nm in certain cases. We have also implemented a correction strategy that enabled the reduction of errors down to 0.3 nm.

Glioblastoma multiforme (GBM) is a glioma and the most aggressive type of brain tumor with a dismal average survival time, despite the standard of care. One promising alternative therapy is boron neutron capture therapy (BNCT), which is a noninvasive therapy for treating locally invasive malignant tumors, including glioma. BNCT involves boron-10-released radiation directly into tumor cells with minimal damage to healthy tissues. This therapy lacks clinically approved targeted blood-brain-barrier-permeating delivery vehicles for therapeutic drug/ boron-10. Nanoparticles, particularly gold nanoparticles (GNPs), are selective and effective drug-delivery vehicles because of their desirable properties, facile synthesis, and biocompatibility. This review discusses historical and current GNP therapeutic applications as a drug delivery vehicle for treating glioma. Furthermore, GNPs loaded with therapeutic drugs, imaging agents, and GBM-targeting antibodies/ peptides to treat GBM will be discussed. Additionally, the importance of upper and lower limits on therapeutic efficacy will be described and explored followed by highlighting their advantages, limitations, and possible toxicity. Recent research and selected important findings for GNP-mediated pharmaceutics in GBM will also be considered.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

Poultry farming in Slovakia has a tradition and an irreplaceable position to ensure rational nutrition for the population. In terms of a nutritional value, poultrymeat (Galliformes) contains a high amount of proteins, essential amino acids, essential unsaturated fatty acids, minerals, vitamins and a low fat content. Poultrymeat production has a relatively short reproductive cycle and thus allows regulating the demand and supply. The poultry market also influences the development of domestic consumption. According to the Statistical Office of the Slovak Republic, the consumption of meat has witnessed a persistent increase over the last 10 years. [1] According to the 2023 AVEC (The Voice of European Meat Sector) annual report, the consumption of poultrymeat in Slovakia was 20.0 kg per person per year. The average consumption in the EU-27 (2021) was 23.4 kg, with the countries with the highest consumption being Portugal (37.8 kg), Ireland (36.0 kg), Hungary (33.5 kg) and Spain (29.9 kg). On the other hand, the countries with the lowest consumption of poultrymeat, apart from Slovakia, also include Austria and Greece with a consumption of 21.5, resp. 21.0 kg [2]. The breeding of broiler chickens, as well as the production and placing on the market of poultrymeat must comply with the requirements laid down by legislation, while the compliance is regularly checked by the competent authorities.

A relativistic positioning system is a set of four emitters broadcasting their proper times by means of light signals. The four emitter times received at an event constitute the emission coordinates of the event. Covariant quantities associated with relativistic positioning systems are analysed relatively to an observer in Minkowski space-time by splitting them in their relative space-like and time-like components. The location of a user in inertial coordinates from a standard set of emission data (emitted times and satellite trajectories) is solved in the underlying 3+1 formalism. The analytical location solution obtained by Kleusberg for the GPS system is recovered and interpreted in a Minkowskian context.

The formal transfer of GNSS under water is not possible. It probably makes sense to talk only about the transformation of GPS into LPS, that is, in the Local Position System. However, the basic methods that are used to solve the problem of Spoofing Detection above water can be used under water. It should be understood that engineering problems are significantly different, since the nature of the propagation of acoustic waves in water and electromagnetic waves in the atmosphere are fundamentally different. In this article, we will limit the navigation with acoustically passive receiver. The receiver “listens” to the buoys and solves the problem of finding its own position based on the coordinates of the buoys (such systems are called GNSS-like Underwater Positioning Systems or GNSS-like UPS). Depending on the scale of system service areas, GNSS-like UPS are divided into global, regional, zonal and local system. In this article, we will limit ourselves to considering only local GNSS-like UPS. The acoustic signal generator transmits a signal simulation of several satellites. If the level of the simulated signal exceeds the signal strength of real satellites, the receiver of UPS will “capture” the fake signal and calculate the false position based on it.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

Aiming at the defects of low precision and time cumulative error, an external wireless signal weighted centroid localization algorithm aided inertial positioning method is designed in this paper. According to the signal strength of each anchor node received at the test point, the distance between the anchor node and the anchor node is obtained by using the attenuation model of the wireless signal. Three anchor nodes are used to measure the distance between the anchor node and the measured point. We can obtain the area to be measured according to the actual situation, the position of the measured point is obtained by the weighted centroid localization algorithm and a combined model of wireless signal aided inertial navigation system is established. The simulation results show that the method can greatly improve the positioning accuracy and restrain the divergence of the longitude error and latitude error.

Wi-Fi fingerprinting positioning systems have been deployed for a long time in location-based services for indoor environments. Combining mobile crowdsensing and Wi-Fi fingerprinting systems could reduce the high cost for collecting the necessary data enabling the deployment of the resulting system for outdoor positioning in areas with dense Wi-Fi coverage. In this paper, we present the results attained in the designing and evaluation of an urban fingerprinting positioning system based on crowdsensed Wi-Fi measurements. We first asses the quality of the collected measurements, highlighting the influence of received signal strength on data collection. We then, evaluate the proposed system by comparing the influence of the crowdsensed fingerprints on the overall positioning accuracy for different scenarios. The evaluation helps gain valuable insight into the design and deployment of urban Wi-Fi positioning systems while also allowing the proposed system to match GPS-like accuracy in similar conditions.

This study sheds light on personal characteristics of and the coping strategies that older Canadians self-identifying as severely anxious post-COVID-19 were more and less prone to gravitate to. Our studied sample consisted of 606 older people residing in 10 Canadian provinces. Participants completed the Geriatric Anxiety Scale – 10 and a personal checklist of everyday coping strategies for mitigating anxiety. Severely anxious older Canadians tended to be in their 60s, and in poor to fair health. They were not significantly more likely to be women or to be chronically ill, nor to self-identify as non-binary or as having a life partner. Older Canadians experiencing severe anxiety were, however, far more likely to normalize their fear and anxiety, challenge their worries, and to relax or meditate. They were less inclined to decrease other sources of stress in their lives, to stay active, and to get enough sleep. We offer anticipatory guidance for mental health program planners and practitioners, and researchers, fruitful avenues of inquiry.

This study focused on the precise detection and concordant analysis of circulating tumor cells (CTCs) to verify the usefulness of CTCs as promising clinical markers. CTCs are traditionally achieved using immune-fluorescence and morphological techniques. By combining two prostate cancer-specific genes (PSA and PSMA) and two epithelial-specific genes (EpCAM and KRT19), the CTC detection efficiency can be enhanced. The detection rates of localized prostate cancer (LPC), locally advanced prostate cancer (LAPC), metastatic hormone-sensitive prostate cancer (mHSPC), and metastatic castration-resistive prostate cancer (mCRPC) were 63.04 % (29/46), 70.59% (34/51), 94.34% (50/53), and 90% (126/140), respectively. Subsequent correlation analysis between the four genes, baseline PSA, and CTC count revealed that only the CTC count correlated with baseline PSA in the localized stages of prostate cancer, whereas all four genes were correlated with baseline PSA and CTC count in the metastatic stages of prostate cancer. The precise detection of CTCs using both numerical and transcriptomic analyses can improve the accuracy of biomarker investigations. This study provides valuable insights into the limitations of serum PSA testing and offers a promising alternative to diagnose and manage prostate cancer via the CTC number and specific genes for prostate cancer.

To solve two key problems in the identification of people who are infected with COVID-19: the first problem is that the identification accuracy is not high enough. The second problem is that present identification method such as nucleic acid testing is expensive in many countries. Methods: So, I decided to design a fast identification method for COVID-19 patients which is based on deep learning. After the model (CoughNet) learns more than 6,000 cough spectrograms of both COVID-19 patients and normal people, the accuracy rate of identification of COVID-19 patients and normal people is higher than 99% in the test set. Structure: This paper is mainly divided into three parts: the first part introduces the main background and research status of the research; The second part introduces the research methods; The third part introduces the specific process of the experiment.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

A method for infrared and cameras sensor fusion, applied to indoor positioning in intelligent spaces, is proposed in this work. The fused position is obtained with a maximum likelihood estimator from infrared and camera independent observations. Specific models are proposed for variance propagation from infrared and camera observations (phase shifts and image respectively) to their respective position estimates and to the final fused estimation. Model simulations are compared with real measurements in a setup designed to validate the system. The difference between theoretical prediction and real measurements is between 0.4 cm (fusion) and 2.5 cm (camera), within a 95% confidence margin. The positioning precision is in the cm level (sub-cm level can be achieved at most tested positions) in a 4x3 m locating cell with 5 infrared detectors on the ceiling and one single camera, at distances from target up to 5 m and 7 m respectively. Due to the low cost system design and the results observed, the system is expected to be feasible and scalable to large real spaces.

This paper addresses the problem of assessing and optimizing acoustic positioning system for underwater target localization with range measurements only. We present a new three-dimensional assessment model to assess the optimal geometric beacon formation whether meet user needs. For the sake of mathematical tractability, it is assumed that the measurements of the range between the target and beacons are corrupted with white Gaussian noise with variance is distance-dependent. Then by adopting dilution of precision (DOP) parameters in the assessment model, the relationship between DOP parameters and positioning accuracy is derived. In addition, the optimal geometric beacon formation that will yield the best performance is achieved by minimizing the values of geometric dilution of precision (GDOP) on condition that the position of target is known and fixed. Next, in order to make sure whether the estimate positioning accuracy over interesting region satisfy the precision needed by the users, geometric positioning accuracy (GPA), horizonal positioning accuracy (HPA) and vertical positioning accuracy (VPA) are utilized to assess the optimal geometric beacon formation. Simulation examples are designed to illustrate the exactness of the conclusion. Unlike other work which only use GDOP to optimize the formation and cannot assess the performance of the specified dimensions, this new three-dimensional assessment model can assess the optimal geometric beacon formation in each dimension for any point in three-dimensional space, which can provide users with guidance advices to optimize performance of every specified dimension.

As people grow a custom to effortless outdoor navigation there is a rising demand for similar possibility indoors as well. Unfortunately, indoor localization, being one of the necessary requirements for navigation, continues to be problem without a clear solution. In this article we are proposing a method for an indoor positioning system using a single image. This is made possible using small preprocessed database of images with known control points as the only preprocessing needed. Using feature detection with SIFT algorithm we can look through the database and find image which is the most similar to the image taken by user. Pair of images is then used to find coordinates of database image using PnP problem. Furthermore, projection and essential matrices are determined allowing for the user image localization ~ determining the position of the user in indoor environment. Benefits of this approach lies in the single image being the only input from user and no requirements for new onsite infrastructure and thus enables a simpler realization for the building management.

This study proposes a mobile positioning method which adopts recurrent neural network algorithms to analyze the received signal strength indications from heterogeneous networks (e.g., cellular networks and Wi-Fi networks) for estimating the locations of mobile statioThis study proposes a mobile positioning method which adopts recurrent neural network algorithms to analyze the received signal strength indications from heterogeneous networks (e.g., cellular networks and Wi-Fi networks) for estimating the locations of mobile stations. The recurrent neural networks with multiple consecutive timestamps can be applied to extract the features of time series data for the improvement of location estimation. In practical experimental environments, there are 4,525 records, 59 different base stations, and 582 different Wi-Fi access points detected in Fuzhou University in China. The lower location errors can be obtained by the recurrent neural networks with multiple consecutive timestamps (e.g., 2 timestamps and 3 timestamps); the experimental results can be observed that the average error of location estimation was 9.19 meters by the proposed mobile positioning method with 2 timestamps.

In recent years, the field of radiotherapy has witnessed remarkable advancements with the integration of artificial intelligence (AI) technologies into clinical practice. Traditionally, radiotherapy treatment planning has been a labor-intensive process, requiring meticulous manual segmentation and optimization. With the advent of AI, particularly deep learning algorithms, the accuracy and efficiency of target delineation and organ-at-risk segmentation have significantly improved. AI-driven algorithms analyze voluminous medical imaging data, enabling rapid and precise contouring, thus expediting the planning phase and reducing inter-observer variability. Furthermore, AI's role extends to treatment plan optimization, where it intelligently explores vast parameter spaces to generate optimal plans tailored to individual patients. This not only saves dosimetrists' time but also enhances plan quality by accounting for complex anatomical variations and personalized clinical goals. In the realm of treatment delivery, AI-powered real-time image guidance enhances the accuracy of patient positioning, ensuring precise radiation targeting. Adaptive radiotherapy, enabled by AI, allows on-the-fly plan modifications in response to anatomical changes, significantly improving treatment accuracy in scenarios like tumor shrinkage or weight loss. Beyond planning and delivery, AI algorithms contribute to outcome prediction by analyzing historical patient data and treatment responses. This predictive capability aids clinicians in making informed decisions and refining treatment strategies for better prognoses. Despite the revolutionary potential, challenges remain in seamlessly integrating AI into clinical workflows. Ethical considerations, data privacy, and algorithm interpretability necessitate cautious implementation. Additionally, fostering interdisciplinary collaboration between AI experts and radiation oncologists is imperative to harness the technology's full potential. This paper explores the impact of AI in four key areas of radiotherapy: automated segmentation, dosimetric and machine quality assurance, adaptive radiation therapy, and clinical outcome prediction.

When overhead lines are impacted by lightning, the traveling wave of the fault contains a wealth of fault information. The accurate extraction of feature quantities from transient components and their classification is fundamental to the identification of lightning faults. The extraction process may involve modal aliasing, optimal wavelet base issues, and inconsistencies between the lightning strike distance and the fault point, which have the potential to impact the effectiveness of recognition. This paper presents a method for identifying lightning strike faults by utilizing Kullback-Leibler (KL) divergence enhanced Variational Mode Decomposition (VMD) and Symmetric Geometry Mode Decomposition (SGMD) improved with Permutation Entropy (PE) to address the aforementioned issues. A model of a 220 kV overhead line is constructed using real faults to replicate scenarios of winding strike, counterstrike, and short-circuit. The three-phase voltage is chosen and then sub-jected to Karenbaren decoupling in order to transform it into zero mode, line mode 1, and line mode 2. The zero mode voltage is decomposed using KL-VMD and PE-SGMD methods, and lightning identification criteria are developed based on various transient energy ratios. The research findings demonstrate that the criteria effectively differentiate between winding strike, counterstrike, and short-circuit faults, thus confirming the accuracy and efficacy of the lightning fault identification criteria utilizing KL-VMD and PE-SGMD.

The direct growth of single-walled carbon nanotubes (SWCNTs) with a narrow distribution of diameter or chirality remains elusive despite significant benefits in properties and applications. Nanoparticle catalysts are vital for SWCNT synthesis, but how to precisely manipulate their chemistry, size, concentration, and deposition remains difficult, especially within a continuous production process from the gas-phase. Here, we demonstrate the preparation of W₆Co₇ alloyed nanoparticle catalysts with precisely tunable stoichiometry using electrospray, which remain solid state during SWCNT growth. We also demonstrate continuous production of liquid iron nanoparticles with in-line size selection. With the precise size manipulation of catalysts in the range of 1-5 nm, and a nearly monodisperse distribution (σ_g < 1.2), an excellent size selection of SWCNT can be achieved. All of the presented techniques show great potential to facilitate the realization of single-chirality SWCNT production.

This paper systematically examines Chinese academic discourse that concurrently addresses Indonesia and Timor-Leste, analysing 137 articles from the China National Knowledge Infrastructure (CNKI) and indexed by the Chinese Social Sciences Citation Index (CSSCI). The analysis reveals significant publication trends, particularly during periods of heightened geopolitical and economic engagement, such as the global expansion of the Belt and Road Initiative (BRI). It identifies predominant themes such as economic cooperation, security concerns, and historical-cultural dynamics. The findings highlight China’s strategic interests and leadership aspirations in Southeast Asia， providing insights into how Chinese scholars perceive and articulate China’s strategic interests and diplomatic efforts in the region involving Indonesia and Timor-Leste.

There is a growing demand for indoor positioning systems (IPS) in a wide range of applications. However, traditional solutions such as GPS face many technical challenges. In recent years, a promising alternative has been emerging: IPS based on visible light communication (VLC), which offers a combination of which is highly accurate, low cost and energy efficient. This article presents a comprehensive review of VLC-based IPS, providing a tutorial-like overview of the system. It begins by comparing various positioning systems and providing background information on their inherent limitations. The mechanisms of VLC-based IPS are then discussed, including a comprehensive examination of their performance metrics and underlying assumptions. The complexity and efficiency of VLC-based IPS is examined by analyzing factors such as channel modeling, signal processing, and localization algorithms. To optimize the system, a variety of strategies are explored. These include the design of efficient modulation schemes, the development of advanced encoding and decoding algorithms, the implementation of adaptive power control, and the use of state-of-the-art localization algorithms. Additionally, system parameters such as LED placement, receiver sensitivity, and transmit power are carefully examined to highlight their impact on energy efficiency and localization accuracy. Altogether, this paper serves as a comprehensive guide to VLC IPS, providing in-depth insights into its vast potential and the challenges it presents.

The increasing focus on the development of positioning techniques reflects the growing interest in applications and services based on indoor positioning. Many applications necessitate precise indoor positioning or tracking of individuals and assets, leading to rapid growth in products based on these technologies in certain market sectors. Ultrasonic systems have already proven effective in achieving the desired positioning accuracy and refresh rates. The typical signal used in ultrasonic positioning systems for estimating the range between the target and reference points, specifically the linear chirp, can undergo shape aberration due to the effects of acoustic diffraction when the aperture exceeds a certain limit. The extent of the aberration is influenced by the shape and size of the transducer, as well as the angle at which the transducer is observed by the receiver. This aberration also impacts the shape of the cross-correlation, causing it to lose its characteristic easily detectable single global peak. In such instances, cross-correlation techniques yield results with a significantly higher error than anticipated. In this study, an alternative technique to global peak detection is proposed, leveraging the inherent symmetry observed in the shape of the aberrated cross-correlation. The numerical simulations, performed using the academic acoustic simulation software Field II, conducted using a typical ultrasonic chirp and ultrasonic emitter, compare the classical and the proposed range techniques in a standard office room. The results demonstrate that the proposed technique enables accurate range estimation even in the presence of severe cross-correlation shape aberrations. This allows the use of emitting transducers with a much larger aperture than that allowed by the classical cross-correlation technique. Consequently, it becomes possible to have greater acoustic power available, leading to improved Signal-to-Noise Ratio (SNR).

Infrared sensors incorporating suspended zinc oxide (ZnO) pyroelectric films and thermally-insulated silicon substrates are fabricated using conventional MEMS-based thin-film deposition, photolithography, and etching techniques. The responsivity of the pyroelectric film is improved through annealing at 500℃ for 4 h. The voltage response of the fabricated sensors is evaluated experimentally for a substrate thickness of 1 µm over a sensing range of 30 cm. The results show that the voltage signal varies as an inverse exponential function of the distance. A positioning system based on three infrared sensors is implemented in LabVIEW. It is shown that the position estimates obtained using the proposed system are in excellent agreement with the actual locations. In general, the results presented in this study provide a useful source of reference for the further development of MEMS-based pyroelectric infrared sensors.

Indoor Positioning Systems (IPSs) are designed to provide solutions for location-based services. Wireless local area network (WLAN)-based positioning systems are the most widespread around the globe and are commonly found to have a ready-to-use infrastructure composed mostly of access points (APs). They provide useful information on signal strength to be processed by adequate location algorithms, which are not always capable of achieving the desired localization error only by themselves. In this sense, this paper proposes a new method to improve the accuracy of IPSs by optimizing some of their most relevant infrastructure components. Included are the arrangement of APs over the environment, the number of reference points (RPs), and the number of samples per location estimation test. A simulation environment is also proposed, in which the impact of key influencing factors on system accuracy is analyzed. Finally, a case study is simulated to validate an optimal combination of design parameters and its compliance with the requirements of localization error and the limited number of access points. Our simulation results clearly show that the desired localization accuracy, which is set as a goal, can be achieved while maintaining the factors already mentioned at minimal levels, which decreases both system deployment costs and computational effort.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

The continuous advancements in healthcare technology have empowered the discovery, diagnosis, and prediction of diseases, revolutionizing the field. Artificial intelligence (AI) is expected to play a pivotal role in achieving the goals of precision medicine, particularly in disease prevention, detection, and personalized treatment. This study aims to determine the optimal combination of the mother wavelet and AI model for the analysis of pediatric electroretinogram (ERG) signals. The dataset, consisting of signals and corresponding diagnoses, undergoes Continuous Wavelet Transform (CWT) using commonly used wavelets to obtain a time-frequency representation. Wavelet images were used for the training of five widely used deep learning models: VGG-11, ResNet-50, DensNet-121, ResNext-50, and Vision Transformer, to evaluate their accuracy in classifying healthy and unhealthy patients. The findings demonstrate that the combination of Ricker Wavelet and Vision Transformer consistently yields the highest median accuracy values for ERG analysis, as evidenced by the upper and lower quartile values. The median balanced accuracy of the obtained combination of the three considered types of ERG signals in the article are 0.83, 0.85, and 0.88. However, other wavelet types also achieved high accuracy levels, indicating the importance of carefully selecting the mother wavelet for accurate classification. The study provides valuable insights into the effectiveness of different combinations of wavelets and models in classifying ERG wavelet scalograms.

In biology molecules and macromolecules like sugars, proteins, DNA, and RNA are of utter importance. Detecting their presence as well as their conformation is still a challenge in many cases. It is well known that the vibrational states of such molecules lie from the infrared to the TeraHertz range. Spectroscopy can be used to detect such compounds and probe their conformation. Still, terahertz spectroscopy on biosample is a challenge for two main reasons: water absorption; and the small size of the samples. The sample volume is smaller than the cube of the TeraHertz wavelength; the light matter interactions are thus extremely reduced. In this paper, we present the design, fabrication, characterization and the first typical uses of a biophotonic device aiming at increasing light matter interaction to enable terahertz spectroscopy of minute samples on a broad band (0.2–2 THz). We demonstrate time domain spectroscopy experiments on few µl samples showing the validity of our approach.

With the rapidly increasing of people’s purchasing power, the fast moving consumer goods (FMCG) industry is supposed to grow dramatically. In order to gain more market access and profile, it is important for the FMCG manufacturers and retailers to find the preferences and provincial characteristics of consumers, to develop more suitable goods distribution strategy. Based on retails marketing data with geographic characteristics, this paper proposes a new combination of geography methods to solve the problems in distribution of FMCG. Via multiple K-means clustering and cross validation of KNN half off, the mesoscopic sales features are extracted through the classification of retails, which can indirectly grasp the consumer behavior characteristics. Based on space division and Moran’ I spatial autocorrelation arithmetic, two strategies are developed to satisfy consumer’s needs and promote sales, including conservative and positive strategies. According to our analysis, the total sales volume of the regions will increase by 5.1% and 10.3%. This study can be applied to the provide purchase strategies for FMCG retails according to their locations. The research can explore the consumption potential of different areas, thus improving the profile of retails and the development of economy in more mesoscopic scale.

The point cloud is a form of three-dimensional data that comprises various detailed features at multiple scales. Due to this characteristic and its irregularity, point cloud analysis based on deep learning is challenging. While previous works utilize the sampling-grouping operation of PointNet++ for feature description and then explore geometry by means of sophisticated feature extractors or deep networks, such operations fail to describe multi-scale features effectively. Additionally, these techniques have led to performance saturation. And it is difficult for standard MLPs to directly "mine" point cloud. To address above problems, we propose the Detail Activation (DA) module, which encodes data based on Fourier transform after sampling and grouping. We activate the channels at different frequency levels from low to high in the DA module to gradually recover finer point cloud details. As training progresses, the proposed Point-MDA can uncover local and global geometries of point cloud progressively. Our experiments show that Point-MDA achieves superior classification accuracy, outperforming PointNet++ by 3.3% and 7.9% in terms of overall accuracy on the ModelNet40 and ScanObjectNN dataset, respectively. Furthermore, it accomplishes this without employing complicated operations, while exploring the full potential of PointNet++.

A software defined radio (SDR) is a communication system that makes use of components that can be configured through software, in contrast to traditional systems where these components are variable through hardware, these radio devices are much more versatile, this article describes the factors that must be considered when implementing a communication system based on Software Defined Radios (SDR), in order to reduce the attenuation factors and thus obtain the maximum distance for a transmission of data effectively in the UHF band. The calculations made for the first Fresnel zone and for the design of the Ground Plane type antennas used in the transmission/reception stages of the x40 bladeRF platforms are also presented. The tests were carried out at the facilities of the Huarangal Nuclear Center of the Peruvian Institute of Nuclear Energy, obtaining favorable results that allow ratifying the versatility and performance of the SDRs.

Centimeter-level localization and rotation angle estimation of flatbed trucks are major problems in unmanned forklift automated loading scenes. To solve it, this study proposes a method for high-precision positioning and rotation angle estimation of flatbed trucks based on BeiDou and vision. First, an unmanned forklift equipped with a ToF camera and double antenna mobile receiver for BeiDou positioning collects depth images and localization data near the front and rear endpoints of the flatbed. Then DDRNet-23-slim was used to segment the flatbed from the depth image and extract the straight lines at the edges of the flatbed using the Hough transform and compute the set of intersection points of the lines. A neighborhood feature vector was designed to locate the endpoint of a flatbed from a set of intersection points by feature screening. Finally, the relative coordinates of the endpoints were converted to a customized forklift navigation coordinate system by BeiDou positioning, and rotation angle estimation was performed by the front and rear endpoints. Experiments showed that the endpoint positioning error was less than 3 cm and the rotation angle estimation error was less than 0.1°. The precision of the method meets the demand for automated flatbed truck loading by unmanned forklifts.

The CoDRIVE solution builds on R&amp;D in the development of connected and autonomous vehicles (CAVs). The mainstay of the system is a low-cost GNSS receiver integrated with a MEMS grade IMU powered with CoDRIVE algorithms and high precision data processing software. The solution integrates RFID (radio-frequency identification) localisation information derived from tags installed in the roads around the University of Nottingham. This aids the positioning solution by correcting the long-term drift of inertial navigation technology in the absence of GNSS. The solution is informed of obscuration of GNSS through city models of skyview and elevation masks derived from 360-degree photography. The results show that predictive intelligence of the denial of GNSS and RFID aiding realises significant benefits compared to the inertial only solution. According to the validation, inertial only solutions drift over time, with an overall RMS accuracy over a 300 metres section of GNSS outage of 10 to 20 metres. After deploying the RFID tags on the road, experiments show that the RFID aided algorithm is able to constrain the maximum error to within 3.76 metres, and with 93.9% of points constrained to 2 metres accuracy overall.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Interactions between mobile robots and human operators in common areas require a high safety especially in terms of trajectory planning, obstacle avoidance and mutual cooperation. In this connection the crossings of planned trajectories, their uncertainty based on model fluctuations, system noise and sensor noise,play an outstanding role. This paper discusses the calculation of expected areas of interactions du ring human-robot navigation with respect to fuzzy and noisy information. Expected crossing points of possible trajectories are nonlinearily associated with positions and orientations of robot and human. The nonlinear transformation of a noisy system input, such as directions of motion of human and robot, to a system output, the expected area of intersection of their trajectories, is done by two methods: statistical linearization and the sigma-point-transformation. For both approaches fuzzy approximations are presented and the inverse problem is discussed where the input distribution parameters are computed from given output distribution parameters.

This paper presents a deep learning-based multi-guidance line detection approach, enabling an autonomous four-wheeled agricultural robot to navigate strip farmland. The integration of Proportional-Integral-Derivative (PID) and Fuzzy Logic Control (FLC) systems optimizes the velocity and heading angle of robot, facilitating smooth navigation along identified guidance line. Enhance cornering maneuverability with real-time kinematics (RTK)-assisted Global Navigation Satellite System (GNSS) (RTK-GNSS) positioning. Additionally, the spraying system combined with deep learning can effectively identify weeds and crop nutrient deficiencies to achieve precise spraying. The guidance system prioritizes irrigation lines for navigation, with additional guidance from crop and furrow lines. Trigonometric analysis determines the angular deviation between the identified guidance line and the vertical line of the top view image. Experiments under diverse weather conditions demonstrate the stable navigation of robot at 12.5 cm/s, achieving up to 90% accuracy in weed and nutrient deficiency identification. The spraying accuracy for weeds and deficiencies averages 87% and 73%, respectively, underscoring the system's contribution to sustainable and precision horticulture practices.

Diversified techniques have been applied in many research papers for the optimization of rehabilitation robotic movements in order to maintain smoothness and accuracy. Smooth and precise control is needed necessarily for upper limb rehabilitation robotic applications having five degree of freedom. The preferred parameters which are used for the controlling were validated by mathematical model and these tuning parameters were optimized. Designing optimization algorithms to control complex physical robots has been a challenging task. In this study, a number of optimization techniques will be analyzed to determine the optimal parameters of a PID controller with a dynamic model of the upper limb rehabilitation system. For determining optimal control parameters for PID, there exists a number of tuning methods such as Zeigler Nichols and fuzzy logic which are classical methods. Swarm intelligence-based optimization algorithms are inspired by the behaviors of living things in nature. Several researchers have reported the optimal design of PID controller parameters using optimization techniques. The proposed control technique has been implemented on a 5-DOF RAX hardware and before any clinical trials, six healthy subjects went for trials under strict protocol. It has been discovered that the proposed control technique rejects the external unwanted disturbances as well as keeps the system stable under extreme perturbed and harsh conditions. In this research paper mathematical models have been validated to determine the PID parameters for the optimization. The comparative study is carried out with four different cost functions since a well-designed objective function leads to better performance of the system and indicates control design expectations. These objective functions are an integral squared error (ISE) and integral absolute error (IAE). In this research work, the effects of different cost functions on optimization techniques for controller parameters were analyzed. The performance of the controller with different cost functions has examined for robustness analysis. The cost function of particle swarm optimization, Firefly, Ant Bee Colony and Ant Colony optimization were developed for the better optimization results.

In this paper, precise examination of multi-port antennas with large mutual coupling between the ports is studied. For this purpose, some vital parameters such as active reflection coefficients and realised gain are emphasized. The main motivation of this research is the ignorance of this issue in several recently published papers. Hence, corrections and criticisms to some recently reported results are presented. At first, a microstrip patch consisting of two inverted U-slots is re-examined, which has been proposed in a recently published paper for wideband applications. However, the authors did not present satisfactory results to indicate the performance of the proposed structure. In reverse, some important parameters such as the antenna gain appear to be incorrectly reported. In this paper, the characteristics of the antenna are compared with a simple 50 Ω microstrip line excited by two probes, indicating no significant differences. In the remainder of this paper, some corrections are provided on two examples of wide-beam circularly polarised multi-fed antennas for satellite applications. The first example is the multi-fed spiral antennas with folded arms, which have been proposed as the widebeam antennas at 435 MHz. It is indicated that the antenna height should be increased for better performance. The second example is the quadrifilar square helical antennas with folded arms, which have been proposed as the widebeam antennas for 435 MHz with minor responses at 145 MHz. Some corrections are presented on the previously reported minor responses at 145 MHz.

Walking of humanoid robots is dependent on precise tracking of the center of gravity and foot trajectories. Trajectory tracking is achieved by mobilizing the robot joints to produce the correct trajectory. Errors are being occurred because of assumptions on tracking the center of gravity and the foot trajectories. In this study, a numerical algorithm has been developed that produces an exact and single kinematic solution in which the center of gravity and foot trajectories can be tracked with the desired precision. The effectiveness of the algorithm was examined with a dynamic simulation and compared with the method given in the literature The main highlight of this study, using the presented algorithm, the robot can walk even if the position of its center of gravity is lower than its hips, resulting tracking error was smaller than reported in the literature.

Ultrasound A-scan is an important tool for quantitative assessment of ocular lesions. However, its usability is limited by difficulty to accurately localize the ultrasound probe to a lesion of interest. In this study, a transparent LiNbO3 single crystal ultrasound transducer was fabricated, and integrated with a widefield fundus camera to guide the ultrasound local position. The novel fundus camera guided ultrasound probe was validated for in vivo measurement of rat eyes. Anterior and posterior segments of the rat eye could be unambiguously differentiated with the fundus photography guided ultrasound measurement. A model eye was also used to verify the clinical potential of the prototype device.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

In this paper, four types of open service signals of BDS-3 satellite (B1I, B1C, B2a, and B3I) and B2I signals broadcasted by BDS-2 satellites were used in the time frequency transfer and positioning experiments with signal coexisting in BDS system, and the single frequency PPP (precise point positioning) method was used. Modified GRoup And PHase Ionospheric Correction (GRAPHIC) method was proposed and verified by the experiment. The results show that 18 selected stations can achieve decimeter-level positioning results with single frequency. Compared with the general observation method, the proposed modified GRAPHIC method improves the stability and precision of positioning and timing significantly, and the positioning accuracy of 5 frequency signals is increased 40.4%, 32.2%, 80.3%, 12.4%, and 10.3%, respectively. The frequency stability can reach the same accuracy as that of dual-frequency with BDS in the current state.

Placing a nasogastric tube (NGT) is a frequent nursing technique in intensive care units. The gold standard for its correct positioning is the chest X-ray due to its high sensitivity but represents a radiation source for critically ill patients. Our study aims to analyze whether the ultrasound performed by an intensive care nurse is a valid method to verify the NGT’s correct positioning and to evaluate the degree of interobserver agreement between this nurse and an intensive care physician in the NGT visualization using ultrasound. Its correct positioning was verified by direct visualization of the tube in the stomach and indirect visualization by injecting fluid and air through the tube ("dynamic fogging" technique). 23 critically ill patients participated in the study. A sensitivity of 35% was achieved using direct visualization, increasing up to 85% using indirect visualization. The degree of interobserver agreement was 0.88. Therefore, the NGT indirect visualization by an intensive care nurse using ultrasound could be a valid method to check its positioning. However, the low sensitivity obtained by direct visualization suggests the need for further training of intensive care nurses in ultrasonography. According to the high degree of agreement obtained, ultrasound could be performed by both professionals.

One of the important issues being explored in Industry 4.0 is a collaborative mobile robots. This collaboration requires precise navigation systems, especially indoor navigation systems where GNSS (Global Navigation Satellite System) cannot be used. To enable precise localization of robots, different variations of navigation systems are being developed, mainly based on trilateration and triangulation methods. Triangulation systems are distinguished by the fact that they allow precise determination of an object’s orientation, which is important for mobile robots. An important feature of positioning systems is the frequency of position updates based on measurements. For most systems it is 10-20 Hz. In our work, we propose a high-speed 50 Hz positioning system based on the triangulation method with infrared transmitters and receivers. In addition, our system is completely static, i.e. it has no moving/rotating measurement sensors, which makes it more resistant to disturbances (caused by vibrations, wear and tear of components, etc.). In this paper we describe the principle of the system as well as its design. Finally, we present tests of the built system, which show centimeter positioning accuracy with a position update frequency of 50 Hz.

Accurate localization of road agents is the basis of intelligent transportation systems, which is still difficult to achieve for GNSS positioning in urban areas due to the signal interferences from buildings. Various collaborative positioning techniques are recently developed to improve the positioning performance by the aid from neighboring agents. However, it is still challenging to study their performances comprehensively. The GNSS measurement error behavior is complicated in urban areas and unable to be represented by naive models. On the other hand, real experiment requiring numbers of devices is hard to be conducted, especially for a large-scale test. Therefore, a GNSS realistic urban measurement simulator is developed to provide measurements for collaborative positioning studies. The proposed simulator employs a ray-tracing technique searching for all possible interferences in the urban area. Then, it categorizes them into direct, reflected, diffracted, and multipath signal to simulate the pseudorange, carrier-phase, 〖C/N〗_0, and Doppler shift measurements correspondingly. The performance of the proposed simulator is validated through real experimental comparisons with different scenarios. The proposed simulator is also applied with different positioning algorithms, which verifies it is sophisticated enough for the collaborative positioning studies in the urban area.

We propose an iterative scheme for feature-based positioning using a new weighted dissimilarity measure with the goal of reducing the impact of large errors among the measured or modeled features. The weights are computed from the location-dependent standard deviations of the features and stored as part of the reference fingerprint map (RFM). Spatial filtering and kernel smoothing of the kinematically collected raw data allow efficiently estimating the standard deviations during RFM generation. In the positioning stage, the weights control the contribution of each feature to the dissimilarity measure, which in turn quantifies the difference between the set of online measured features and the fingerprints stored in the RFM. Features with little variability contribute more to the estimated position than features with high variability. Iterations are necessary because the variability depends on the location, and the location is initially unknown when estimating the position. Using real WiFi signal strength data from extended test measurements with ground truth in an office building, we show that the standard deviations of these features vary considerably within the region of interest and are neither simple functions of the signal strength nor of the distances from the corresponding access points. This is the motivation to include the empirical standard deviations in the RFM. We then analyze the deviations of the estimated positions with and without the location-dependent weighting. In the present example the maximum radial positioning error from ground truth are reduced by 40% comparing to kNN without the weighted dissimilarity measure.

When an earthquake or a large fire has occurred, it is difficult to secure communication networks for rescue in the building due to the destruction of commercial communication networks. Although analog radio systems such as VHF (very high frequency) and UHF (ultra-high frequency) are used for rescue operation in general, communication failure occurs in closed spaces, causing difficulties in smooth rescue operations. When the communication infrastructures have been destroyed in a building in the disaster, an emergency wireless telecommunication environment should be constructed to secure a safer disaster response environment. In this study, along with comparison of the performances of diverse communication frequencies, UWB (Ultra-Wide Band) wireless telecommunication networks were evaluated under five building indoor environment conditions including open spaces. UWB communication modules were fabricated to satisfy the IEEE (The Institute of Electrical and Electronics Engineers) 802.15.4a standard performance to measure distances in which communications are possible according to the indoor environment for each of six channels with different UWB communication frequencies. The results indicated that the distances in which communications are possible for each the six channels were average 15.5 m, maximum 20 m in open spaces; average 17.33 m, maximum 20 m in corridors; average 15.3 m, maximum 20 m in indoor office environments with office fixtures; average 4.33 m, maximum 6 m in vertical spaces of stairs; and average 6.5 m, maximum 17 m in closed horizontal spaces with a fire door. In this case, the communication performance and distance performance were shown to be the most excellent at a frequency (Centre Frequency) of 6489.6 and a band of 5980.3 – 6998.9 MHz, which is UWB 7ch. In conclusion, it is judged that if UWB communication modules are installed in the disaster area at intervals of 20 m and multi-channels are used, communication environments can be constructed even in closed spaces

Despite being a rare disease worldwide, rabies has the highest morbidity and mortality rates, with nearly all symptomatic cases leading to coma and death. Rabies represents an infectious disease caused by the Rabies virus (RABV), which is part of the Lyssavirus group and the Rhabdoviridae family, and it mainly spreads through the bite and scratch of an infected mammal, but particularly of wild animals, such as bats, foxes, wolves and racoons, and of domestic animals, such as dogs and cats, in rabies-prone areas of the world. Airborne transmission has been deemed as extremely rare, and no clinical case as such has been recorded worldwide yet, except in the enclosed environment, such as research laboratories and caves where infected bats are present. Domestic mammals, such as dogs and ferrets, represent other important reservoirs of disease transmission, and the human cases of Asia and Africa amount approximately 95% of all human cases worldwide. Infected animals most commonly start transmitting the virus once the first symptoms have occurred, and if they experience disease aggravation and death within 10 days, a case of rabies is registered, more easily if the incidence occurred in the urban area and then, any person or animal that had been potentially exposed are strongly recommended to receive the inoculation. It is rare for asymptomatic mammals to transmit the illness. Most First-World and several Second-World countries have recently been declared dog rabies-free by the World Health Organization. The disease can only be treated prophylactically, with three doses of a vaccine containing an inactivated form of RABV, or with five doses of the vaccine and two doses of anti-RABV immunoglobulins within 28 days if the patient is believed to have been exposed to the virus beforehand. It has been projected that, once the viral load reaches elements of the central nervous system, prophylactic approaches are no longer effective, even if symptoms have not begun yet, and this highlights the urgent trait of the medical condition, strongly recommending exposed people to receive the prophylactic doses immediately after the potential exposure to the virus. The pathogen first infects the bodily fluids, before reaching the peripheral nervous system, from where it will gradually move toward the spinal cord or the encephalon, at a speed of movement ranging from 1 to 40 cm per day. It was also found, in extremely rare circumstances, to infect the nasopharyngeal cavity and the lungs. The primary cause of a successful, gradual advance of the viral load toward the point of clinical no-return for the patient - the CNS - is a complex mechanism of induced innate immune evasion, with the interferon system being heavily targeted and silenced by RABV proteins. The ‘Milwaukee’ protocol is locally believed to decrease the mortality rate of the clinical illness to approximately 80%, although significantly more research is required in this sense. First-line immune evasion represents the central mechanism developed by viruses during their evolutionary process to gain control over human immunity, so it could be the development and adjustment of a counter-offensive to this evolutionary operating system that could address the core elements of the problem. Human recombinant Type I and Type III Interferons were found to be significant vaccine adjuvants and to considerably delay the clinical onset of the disease. Despite their central role in natural immunity-based prophylaxis, vaccine support and, in often cases, vaccination per se, a local administration of IFNs as such may not be enough to tackle the core problem of the endemic disease, and a specific and systemic treatment of potential host cells with IFN I and III, as well as IFN-stimulating proteins, may constitute a major research requirement in the coming years of disease investigation, as the inoculation efforts with the inactivated virus and immunoglobulin administration continue. The administration of a relatively low dosage of somatic Natural Killer cells, gamma-interferon and perhaps, of somatic helper CD4+ and somatic cytotoxic CD8+ T-lymphocytes treated with alpha-, beta- and lambda-interferon could be merged with the administration of a similar dosage of alpha-, beta- and lambda-interferon during the efforts to develop an effective and less costly prophylactic vaccine against rabies. A combination of a nasal substance containing a low dosage of IFN I and III with a reduced concentration of neutralized RABV copies, and/or with a low dose of anti-RABV IgA antibodies, could also be tested for humans for the purposes of pre- and post-exposure prophylaxis.

Pharmaceutical aerosols play a key role in the treatment of lung disorders, but also systemic diseases, due to their ability to target specific areas of the respiratory system (RS). This article focuses on identifying and clarifying the influence of various factors involved in the generation of aerosol micro- and nanoparticles on their regional distribution and deposition in the RS. Attention is given to the importance of process parameters during aerosolization of liquids or powders and the role of aerosol flow dynamics in RS. The interaction of deposited particles with the fluid environment of the lung is also pointed out as an important step in the mass transfer of the drug to the RS surface. The analysis presented highlights the technical aspects of preparing the precursors to ensure that the properties of the aerosol are suitable for a given therapeutic target. Analyzing existing technical limitations, several potential strategies for enhancing the efficiency of targeted therapeutic delivery to or through the respiratory system are identified and presented, including the use of smart inhaling devices incorporating AI algorithms.

Neurodegeneration is an age-dependent progressive phenomenon with no defined cause. Aging is the main risk factor for neurodegenerative diseases. During aging, activated microglia undergoes phenotypic alterations that can lead to neuroinflammation, which is well accepted event in the pathogenesis of neurodegenerative diseases. Several common mechanisms are shared by genetically or pathologically distinct neurodegenerative diseases, such as excitotoxicity, mitochondrial deficits and oxidative stress, protein misfolding and translational dysfunction, autophagy and microglia activation. Progressive loss of neuronal population due to increased oxidative stress leads to neurodegenerative diseases mostly due to the accumulation of dysfunctional mitochondria. Mitochondrial dysfunction and excessive neuroinflammatory responses are both sufficient to induce pathology in age-dependent neurodegeneration. Therefore, mitochondrial quality control is key determinant for the health and survival of neuronal cells in the brain. Research has been primarily focused to demonstrate the significance of neuronal mitochondrial health, despite the important contributions of non-neuronal cells that constitutes significant portion of the brain volume. Moreover, mitochondrial morphology and function are distinctly diverse in different tissues; however, little is known about their molecular diversity among cell types. Mitochondrial dynamics and quality in different cell types markedly decides the fate of overall brain health, therefore it is not justifiable to overlook non-neuronal cells and their significant and active contribution in facilitating overall neuronal health. In this review article, we aim to discuss the mitochondrial quality control of different cell types in the brain and how important and remarkable is the diversity and highly synchronized connecting property of non-neuronal cells in keeping the neurons healthy to control neurodegeneration.

As most of the current dynamic positioning systems are based on model ships, they cannot accu-rately reflect the motion state, position changes, and mutual influence of each part of the dynamic positioning system of actual ships in complex environments. Other actual ships such as cargo ships cannot add various sensors and auxiliary equipment to verify and analyze the positioning system. This article takes the intelligent research and training dual-use ship of Dalian Maritime University, which integrates scientific research and training, as the object of study. This ship will not be affected by the voyage period and route and can choose a suitable sea area for research. Therefore, in order to improve the accuracy and reliability of the dynamic positioning system, research on the ship’s dynamic positioning system was carried out. Firstly, an accurate mathematical model of ship motion was established, and the hydrodynamic derivatives of ship model motion were obtained by nu-merical calculation, and applied to the three-degree-of-freedom model of the intelligent research and training dual-use ship. Then, the model was used as part of the closed-loop simulation model of the ship’s dynamic positioning system, and the terminal sliding mode controller was used for sim-ulation and emulation, thereby obtaining ideal simulation test results. This research helps to im-prove the accuracy and reliability of the dynamic positioning system and provides new ideas and methods for ship motion control.

3D-mapping-aided (3DMA) global navigation satellite system (GNSS) positioning that improves positioning performance in dense urban areas has been under development in the recent years, but it still faces many challenges. This paper details a new algorithm that explores the potential of using building boundary for positioning. Rather than applying complex simulations to analyze and correct signal reflections by buildings, the approach utilizes a convolutional neural network to differentiate between the sky and building in a sky-pointing fisheye image. A new skymask matching algorithm is then proposed to match the segmented fisheye images with skymasks generated from a 3D building model. Each matched skymask holds a latitude and longitude coordinate to determine the precise location of the fisheye image. The results are then compared with the conventional GNSS and advanced 3DMA GNSS positioning methods. The aims of the proposed algorithm are to increase positioning and heading accuracy in a rich urban environment.

An novel indoor positioning method of pigsty based on Ultra Wideband (UWB) technology is proposed via reasonably arranging the base stations (BTS) and positioning tags, which can provide a strong support for the accurate positioning of specific pig pens in the pig house. The distribution of Dilution of Precision (DOP) values are analysed in different deployment schemes which includes the amount, the height, the deployment shape and distance of BTS, though positioning simulation. Moreover, the positioning effect of dynamic following positioning (DFP), the root-mean-square error (RMSE) and variance of static positioning (SP) are measured. It is noteworthy that Kalman filtering algorithm is adopted to smooth the DFP experimental data for reducing the positioning error. The simulated results show that the DOP values decrease with the increasing of the height and the distance, and these results and laws are consistent with the experimental results. However, the DOP values are reached best when the height is from 1.75 m to 2.75 m, and the distance is over 3.00 m. Furthermore, the DOP values of quadrilateral deployment is smaller than the one of triangle. In addition, variance of SP and DFP are decreased by utilizing Kalman filtering algorithm. Therefore, the excellent positioning system and its solutions in pigsty can be provided by our proposed indoor positioning method.

With the renewed interest for lunar surface exploration, the European Space Agency envisions to stimulate the creation of lunar communications and navigation services (LCNS) to enable, among others, autonomous navigation capabilities for lunar rovers. As the number of satellites foreseen in such a service is much smaller compared to Earth based global navigation satellite systems (GNSS), different complementary technologies are pursued to improve the attainable navigation accuracy for lunar rovers. One way to improve the position accuracy provided by the LCNS satellites is to constrain the vertical position using a high resolution digital elevation model (DEM). This article presents the results of a variance covariance analysis of an extended Kalman filter (EKF) implementation in which the LCNS ranging measurements are used together with DEM from the LRO LOLA instrument. Assuming a realistic orbit determination and time synchronization (ODTS) accuracy of the LCNS satellites, the usage of a navigation grade IMU and an oven controlled crystal oscillator (OCXO), a 3-sigma position accuracy of less than 10 meters can be obtained. Furthermore, the availability is substantially improved as the DEM aided solution enables a position solution in case of only 3 visible satellites.

The node position information is critical in the wireless sensor network (WSN). However, the existing positioning algorithms commonly have low positioning accuracy because of noise interferences in communication. To solve this problem, this paper presents an iterative positioning model based on distance correction to improve the positioning accuracy of the target node in WSN. First, the log-distance distribution model of received signal strength indication (RSSI) ranging is built and the noise impact factor is derived based on the model. Second, the initial position coordinates of the target node are obtained based on the triangle centroid localization algorithm, thereby calculating the distance deviation coefficient under the influence of noise. Then, the ratio of the distance measured by the log-normal distribution model to the median distance deviation coefficient is taken as the new distance between the anchor node and the target node. Based on the new distance, the triangular centroid positioning algorithm is used again to calculate the target node coordinates. Finally, the iterative positioning model is constructed, and the distance deviation coefficient is updated repeatedly to update the positioning result until the set number of iterations is reached. Experiment results show that the proposed iterative positioning model can improve positioning accuracy effectively.

Development and deployment of wheat varieties with high yields, wide adaptability, good quality, multiple-resistance to abiotic and biotic stresses, and efficient response to fertilizers have greatly contributed to global wheat sustainable production. The genomic composition of key commercial wheat variety can help understand the genetic basis underlying the development of new variety and permit increased breeding efficiency. In this study, we report the chromosomal and genomic compositions of BN207, presently the leading wheat variety in the southern region of Huang-Huai River Valley, the most important wheat producing area in China through an integrated analysis using fluorescent in situ hybridization (FISH) and wheat 15 K SNP array. Our results showed that BN207 inherited 55.3% and 40.7% of its genome from its male parent BN64 and female parent ZM16, respectively, and generating 64 novel or recombined loci. Besides, we detected nine chromosomal variations in Bn207 and its parents and ten sister lines, and physically mapped two variations, the pericentric inversion of chromosome 6B, and large tandem repeat sequence block at the long arm of 5A, both had positive effects on agronomic traits, by integration of FISH and SNP loci recombination analyses. These results will provide a reference for breeding of high yield wheat varieties as BN207, and the application of founder parents BN64 and ZM16, which are being utilized frequently in wheat breeding programs in Henan Province and surrounding areas.

We investigate the impact of aging on exchangeable inter-arrival times in mixed renewal processes, exploring its implications for reliability and survival analysis. In this study, first, we revisit the definition of renewal point processes, where inter-event time intervals are considered as exchangeable non-negative random variables. Then, we define the concept of statistical aging as latency in the observational process of event counting. Latency affects event detection but preserves exchangeability. However, it may alter the statistical properties of inter-event time intervals. Our analytical and numerical assessments highlight the significance of aging in exchangeable lifetimes, offering insights into key metrics such as the failure survival function, renewal function, and hazard rate function. Through archetypal examples and empirical findings, we illustrate the implications of aging on renewal processes. In particular, employing a Bayesian perspective, we analyze high-frequency currency exchange rate data to assess the impact of aging on volatility risk evaluation. This study contributes novel insights to the literature of renewal theory and survival analysis, emphasizing the role of latency aging in stochastic point processes under exchangeability assumption.

We consider a Cauchy problem for differential equations in a Hilbert space $X$. The problem is stated in a time interval $I$, which can be finite or infinite. Weuse a fixed point argument for history-dependent operators to prove the unique solvability of the problem. Then, we state and prove convergence criteria for both a general fixed point problem and thecorresponding Cauchy problem. These criteria provide necessary and sufficient conditions on a sequence $\{u_n\}$ which guarantee its convergence to the solution of the corresponding problem, in the space of both continuous and continuously differentiable functions. We then specify our results in the study of a particular differential equation governed by two nonlinear operators. Finally, we provide an application in viscoelasticity and give a mechanical interpretation of the corresponding convergence result.

First came the digital banks without offices, and then the “fintech” companies that combined technology and finance to achieve greater efficiency and new business models. Later was the turn of transport and logistics, understood as the sector whose economic activities derived from the transport of people and goods, while on the one hand, it has had a new spring thanks to factors such as online sales. Then, perhaps catalyzed by the pandemic scenario, the turn has reached education, where years ago was only a complement of traditional education, now is a central part with multiple modern methodologies. Numerous studies exist about using or implementing these e-learning procedures, but technical analysis is barely found in references. This work aims to analyze the digital transformation of the main sectors of our society, including finances, transport, and education, together with several examples of how technology was helping to fight the pandemic scenario.

In recent years, the application of Indoor Positioning Systems (IPS) has experienced a significant increase in demand, with the aging of the world’s population and their changing lifestyles. While outdoor positioning systems, such as the Global Positioning System (GPS), have significantly advanced over the years, indoor positioning has been restrained by the limitations of the employed technologies. This paper presents a hybrid wireless positioning system able to locate wearables indoor accurately. It is based on the Wi-Fi and Bluetooth technologies, by using trilateration to determine the position of Bluetooth low energy (BLE) wearable devices with an accuracy of up to 1.8 meters. A graphical user interface (GUI) was used to illustrate the performance of the proposed systems, by allowing users to visualize the captured data in two dimensions and three- dimensions in real-time.

Lymphedema is a chronic and debilitating disease that affects up to 250 million patients worldwide. Recent advances in understanding its pathophysiology, along with improved diagnosis and microsurgical techniques, have enhanced our ability to cope with the challenging task of treating this disease. This review provides an overview of the disease from a surgeon's point of view, including existing imaging modalities used for preoperative assessment, as well as surgical procedures used in its treatment. Advantages and drawbacks of various existing modalities used for pre or intraoperative assessment of lymphatic vessels are discussed. Lymphedema treatment has shifted from palliative debulking procedures (liposuction and direct excision) to those aimed at restoring lymphatic flow and countering the pathophysiology of the disease (lymphaticovenous anastomosis and vascularized lymph node transfer). A combination of both approaches can result in a synergistic benefit for patients and are discussed in this review. Despite recent advances, some controversies persist, and further studies are needed to better define surgical treatment algorithms.

To enhance industrial competitiveness and increase productivity, every country has strived to create a smart factory by introducing technologies such as Internet of Things, big data and artificial intelligence into production line and build cyber-physical system for the purpose of promoting manufacturing efficiency. For mission assignment, production line management or manufacturing field analysis, the location information of employee, machine and material is very essential. To promote manufacturing efficiency, of course, the location information became more important. A Bluetooth low energy (BLE) positioning system for the manufacturing is developed in this research. A "Tag tracking" mechanism is addressed and adopted, which uses Beacon to catch the location information and a BLE receiver is also used to receive the broadcasting information from Beacon. The position information from the BLE receiver will be compared with the data in the database for calculating the location of the target. The status of the target may also be obtained by using the data from the BLE receiver. Comparing with the mobile device, this method can reduce energy consumption and make the maintenance simple and easy. In the real applications, the target may not be limited to human. The "Regional label positioning technology" is also investigated in this research. Defining a suitable zone location and arranging BLE receiver location, and positioning analysis theory are the key factors included in this developed technology. The developed system will be tested for real industry applications. The test results show that the feasibility of this technology.

INTRODUCTION: While postmenopausal osteoporosis management evolved in recent years, it nonetheless remains underdiagnosed and undertreated. Given that general practitioners are the keystone of patient screening and referral in France, the present study was conducted to assess their professional positioning in the management of postmenopausal osteoporosis. METHODS: The present is a qualitative study based on semi-directed interviews, carried out between July 2020 and February 2021, with randomly chosen Alsatian general practitioners. Interviews were conducted until data saturation. Consolidated criteria for qualitative research reporting grid was used as well as Nvivo software to categorize the datas. RESULTS: Twenty-three general practitioners (GPs) were interviewed. Study participants recognized that the investigation and treatment of osteoporosis begins at a primary care level, typically with the GP. While some initiated screening by prescribing bone mineral density (BMD) assessments, only few prescribed the associated laboratory assessment and spinal X-rays in search of curable osteopathy or vertebral fracture. For those GPs who do take the opportunity to initiate treatments for patients, there is an understanding that first line options often include calcium and vitamin D, at a “preventive” level. The interviewed physicians interacted mainly with gynecologists and rheumatologists. Fracture liaison services were widely acclaimed. Several barriers were identified in their care management. The absence of a defined role between specialists and the lack of communication between the latter were an additional highlighted barrier. CONCLUSION: This study sheds further light on the discrepancy between the means available to treat osteoporosis, and the modest impact of the care observed.

Monitoring of the surface operations using movement and surveying radar (MSR) can prevent loss of life, equipment, production and loss of the mine. Slope monitoring using MSR is an important aspect of open-pit mining as it provides real-time movement of deformation data for the slope. It is therefore important that the radar is accurately geo-referenced in order to provide accurate real-time movement data. Geo-referencing is defined as the process of determining an instrument’s position (in the form of Easting, Northing, Height) as well as the orientation with respect to the mine’s local coordinate system. This helps in getting geo-referenced data points from the radar that are identified by a unique set of coordinates in relation to the mine’s coordinate system which allows the radar to track movement for a specific set of coordinates. In this research, we assess the performance of geo-referencing a radar using the total station method and compare it with the integration of Advance Navigation – Spatial Dual GPS system connected via RS422 on the MSR. This includes usage of the Spatial Dual navigation coordinates output to calculate the radar’s position relative to the mine local coordinates and mapping the radar’s azimuth, elevation and Range (Az, El and Rl) values to the measured pit-slope data points. Furthermore, a comparison of key attributes of both methods of geo-referencing is performed using a matrix system and giving an overall performance appraisal of both systems. Integrating a navigation system allows the radar to have an auto geo-referencing functionality that will reduce the time spent in completing this process. The findings reveal that the GPS obtained a higher score than the total station with prism method on the weighted matrix system. The total station was found to be more accurate than the GPS however, the deployment time for the GPS is quicker than that of the total station. This is important for different operation such as strip and open-pit mining to choose the preferred method of geo-referencing depending on the level of accuracy required.

Precise and fast position tracking is essential for the correct operation of many industrial robots and CNC machine tools. This subject is also important in the control of the mount of the astronomical telescope, especially for the tracking of artificial satellites. As system parameters can change, a control method that is robust to changes in parameters must be used. Such a method is the sliding control, which, however, ensures the robustness only after reaching the sliding surface. Therefore, a new method was proposed in the paper, which eliminates the phase of reaching the sliding surface. The method consists of using a reference trajectory generator and determining the generalized error in relation to this trajectory. The procedure for designing the control system is presented. Next, the proposed method was verified on the laboratory stand. The described control method provides a robust system operation and can be easily implemented in the control system.

This paper proposes a real-time local positioning system (RT-LPs) utilizing a mobile platform equipped with three anchor nodes placed in a right-angle triangle formation for a real-time locating system (RTLS). After deriving an analytic formula to calculate the target position utilizing the measured distances among anchor nodes and the target node, we find that four parameters have an effect on the position error of the target node. The spacing between anchors is a design parameter that must be large enough to the reduce position error. However, the distance from the anchor node to the target node is an operation parameter that must be small enough to reduce the position error. Additionally, the measured ranges among the anchors and the target node have probabilistic distributions with a mean and variance, which are dominant parameters that have effects on the position error. A comparison study was conducted to determine the effects of the parameters of the target position in both a simulation and an experiment, showing rates of approximately 4% ~ 10%. These findings indicate that our simulation can work properly with the proposed method after assuming that the distance error is a Gaussian model.

Schizoaffective disorder and its classification have always been a topic of discrepancy among researchers. The overlapping presentations of schizoaffective disorder, schizophrenia and psychotic bipolar disorder makes it difficult to classify and diagnose. This study is a narrative review of literatures and genetic and epidemiological research evidences, done to determine the similarities and differences between schizoaffective and psychotic bipolar disorder. Beginning from the introduction of schizoaffective disorder as "schizoaffective psychosis" by Kasanin in 1933, various researchers have proposed different views regarding the diagnosis and classifications for schizoaffective disorder. DSM-III considered schizoaffective disorder as a diagnosis of exclusion as it fails to fit the definite diagnostic criteria of schizophrenia, major affective disorders, or schizophreniform disorder. DSM-V updated the criteria of schizoaffective disorder and stated it as a life time illness rather than being an episodic disorder as in DSM-IV and hence is more reliable. However, some studies show that schizoaffective disorder patients are more like schizophrenia than mood disorder. It still remains unclear whether schizoaffective disorder is a heterogenous disease, a form of schizophrenia, a form of mood disorder or a midpoint in the continuation spectrum of schizophrenia and psychotic bipolar disease.

3D object detection is essential for an accurate and reliable autonomous driving system. Currently, the methods used by the state-of-the-art two-stage detectors are not flexible enough and their fea-ture extraction capabilities are very limited to cope effectively with the disorder and irregularity of point clouds. In this paper, we combine the advantages of both PV-RCNN and PAConv (Position Adaptive Convolution) to create a completely new network, FANet, in order to overcome the ir-regularity and disorder of point clouds. The convolution in our network builds convolutional ker-nels from a basic weight matrix, whose combined coefficients are learned adaptively by LearnNet from relative points. This network allows for flexible modeling of complex spatial variations and geometric structures in the 3D point cloud, enabling better extraction of point cloud features and producing high-quality 3D proposal boxes. Compared to other methods, FANet is superior in terms of 3D object detection accuracy. Extensive experiments on the KITTI dataset have shown a signif-icant improvement in our approach.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

Vienna Atomic Line Database (VALD) contains data on atomic and molecular energy levels and parameters of spectral lines required for stellar spectra analysis. Hundreds of millions lines for fine spectral synthesis and for opacity calculations are collected in present version of VALD (VALD3). Critical evaluation of the data and the diversity of extraction tools support high popularity of VALD among users. The data model of VALD3 incorporates obligatory links to the bibliography making our database more attractive as publishing platform for data producers. The VALD data quality and completeness are constantly improving allowing better reproduction of stellar spectra. To illustrate continuous evolution of the data content we present a comparative analysis of the recent experimental and theoretical atomic data for Fe-group elements, which will be included in the next VALD release. This release will also include a possibility for extracting the line data with full isotopic and hyperfine structures.

With the urgent need of precise positioning faced by internet of things (IoT) applications, the universality and cost of indoor positioning devices become key factors. Since the 5G network has been widely deployed, new opportunity is brought by tightly fusing the traditional low-cost sensors, i.e., the magnetometer. In this study, using 5G channel state information (CSI) and geomagnetic data, a multi-input convolutional neural network (CNN) localization system was proposed. First, to generate a data tensor that is easy for CNN processing, the raw data was reconstructed individually. Then, to comprehensively incorporate the features of 5G CSI and geomagnetic strength data, the ReLU function was chosen as the activation function of the convolutional layer. After that, a multi-input CNN was trained using the incorporated geomagnetic strength and CSI amplitude in the off-line side, and the trained CNN was recorded as a location fingerprint, which can be used for the user position prediction. Finally, in the online side and using a multi-input CNN, the 2-D coordinates are estimated and tested indoors in a typical conference room scenario. The results showed that longer sampling time of fingerprint data result in better uniqueness of the reference point, while the data collection time of locating points does not need to be long. Taking the positioning efficiency and accuracy into consideration, a sampling time of 3s at the reference point and 0.2s at the locating point are recommended. The positioning accuracy using the proposed method was 1.41 m, with an improvement of 22.9% compared with the 5G positioning, and an improvement of 18.0% compared with the 5G and geomagnetic fusing positioning using single CNN.

Recently, there has been remarkable progress in the development of smart textiles, especially knitted strain sensors, to achieve reliable sensor signals. Stable and reliable electro-mechanical properties of sensors are essential for using textile-based sensors in medical applications. How-ever, challenges associated with significant hysteresis and low gauge factor (GF) values remain for using strain sensors for motion capture. To evaluate these issues, a comprehensive investiga-tion of the cyclic electro-mechanical properties of weft-knitted strain sensors was conducted in the present study to develop a drift-free elastic strain sensor with a robust sensor signal for mo-tion capture for medical devices. Several variables were considered in the study, including the variation of the basic knit pattern, the incorporation of the electrically conductive yarn, and the size of the strain sensor. The effectiveness and feasibility of the developed knitted strain sensors are demonstrated through experimental evaluation, by determining the gauge factor, its non-linearity, hysteresis and drift. The developed knitted piezoresistive strain sensors have a GF of 2.4, a calculated drift of 50 %, 12,5 % hysteresis, and 0.3 % nonlinearity in parts.

In surveying engineering tasks, close-range photogrammetry belongs to leading technology considering different aspects like the achievable accuracy, availability of hardware and software, accessibility to measured objects, or the economy. Hence, constant studies on photogrammetric data processing are desirable. Especially in industrial applications, the control points for close-range photogrammetry are usually measured using total stations. In the case of small objects, more precise positions of control points can be obtained by deploying and adjusting a three-dimensional linear network set up on the object. The article analyzes the accuracy of the proposed method, based on the measurement of the linear network using a tape with a precision of ±1 mm. The experiment shows that the adjusted positions of the network control points can be determined with high, one-millimeter accuracy. The photogrammetric 3D model derived referring to such control points and stereo-images captured with a non-metric camera is also characterized by the highest possible precision, which qualifies the presented method to accurate measurements used in surveying engineering. The authors prove that the distance between two randomly optional points derived from the 3D model of a dimensioned object is equal to the actual distance measured directly on it with one-millimeter accuracy.

This study assesses the impact of nurse-originated changes in central venous catheter (CVC) management on the incidence of central line-associated bloodstream infections (CLABSI) and catheter-related bloodstream infections (CRBSI). It is a single-center retrospective cohort study conducted at an urban, tertiary referral, and academic center serving pediatric patients. The study cohort comprised 236 patients and 323 CVCs seen between 2012 and 2022. CLABSI and CRBSI were defined according to the Centers for Disease Control and Prevention definitions. Oncology nurse leaders developed CVC-specific educational modules for CLABSI prevention. All relevant information during the CVC maintenance period was noted in the patient's CVC logbook. 24 (7%) cases of confirmed CLABSI were identified. The incidence of CVC-related infections was 0.32 cases per 1000 catheter days. The incidence decreased by 40% between the first and second three-year study period. Documented exit-site infection was reported in 32 (10%) cases. The correlation between exit-site infection and CLABSI was found in 9 (28%) cases. Our CVC-related infection rates are significantly lower than the incidence reported by the Italian Association of Pediatric Hematology and Oncology, which settles at 3-5 cases per 1000 catheter days. Our data confirm the effectiveness of local CVC management guidelines in preventing CVC-related infectious complications.

(1) Background: Considering highly selected patients with ductal carcinoma in situ (DCIS), active surveillance is a valid alternative to surgery. Our study is aimed at showing the reliability of post-biopsy complete lesion removal, documented by mammogram, as additional criterion to select these patients. (2) Methods: 2173 Vacuum Assisted Breast Biopsies (VABB) documented as DCIS have been reviewed. Surgery has been performed in all cases. We retrospectively collected the reports of post-VABB complete lesion removal and the histological results of the biopsy and surgery. We calculated the rate of upgrade of DCIS identified on VABB upon excision for patients with post-biopsy complete lesion removal and for those showing residual lesion. (3) Results: We observed 2173 cases of DCIS: 408 classified as low grade; 1262 as intermediate grade; 503 as high grade. The overall upgrading rate to invasive carcinoma was 15.2% (330/2173). The upgrade rate was significantly lower (8.2%) when considering patients showing mammographically documented complete removal of the lesion. (4) Conclusion: The absence of mammographically documented residual lesion following VABB is associated to a lower upgrading rate of DCIS to invasive carcinoma on surgical excision and should be considered when deciding the proper management DCIS diagnosis.

The late universe contains a wealth of information about fundamental physics and gravity, wrapped up in non-Gaussian fields. To make use of as much information as possible it is necessary to go beyond two-point statistics. Rather than going to higher order N-point correlation functions, we demonstrate that the probability distribution function (PDF) of spheres in the matter field (a one-point function) already contains a significant amount of this non-Gaussian information. The matter PDF dissects different density environments which are lumped together in two-point statistics, making it particularly useful for probing modifications of gravity or expansion history. Our approach in Cataneo et. al. 2021 extends the success of Large Deviation Theory for predicting the matter PDF in ΛCDM in these “extended” cosmologies. A Fisher forecast demonstrates the information content in the matter PDF via constraints for a Euclid-like survey volume combining the 3D matter PDF with the 3D matter power spectrum. Adding the matter PDF halves the uncertainties on parameters in an evolving dark energy model, relative to the power spectrum alone. Additionally, the matter PDF contains enough non-linear information to substantially increase the detection significance of departures from General Relativity, with improvements up to six times the power spectrum alone. This analysis demonstrates that the matter PDF is a promising non-Gaussian statistic for extracting cosmological information, particularly for beyond ΛCDM models.

Current commitments by European governments seek to improve energy consumption as a means to reduce carbon emissions from building stock by 2050. Within such context, retrieving reliable three-dimensional contours from point clouds becomes an important step in developing facade retrofitting solutions since facade retrofitting projects often make use of as-built 3D models to help reduce inaccuracies by narrowing interpretation and measurement errors. This work aims to provide a method that uses topology-based parametric modelling for reconstructing building envelopes from point clouds. Through a semi-automated process that gives permanent visual feedback, the user adjusts parameters to custom standards of acceptability. A solution under the form of a Grasshopper definition delivers building envelope 3D contours in various file formats as a means for increasing interoperability. The main contributions of this work consist of a parametric reconstruction workflow capable of solving building topology for retrieving 3D contours, a strategy to bypass point cloud occlusion, and a strategy for converting those contours into an IFC model directly from the parametric modelling environment.

In this paper, we present a relapse based demonstrating way to deal with investigate various arrangement MTC information. A commonplace use of this displaying approach incorporates three stages: first, define a model that approximates the connection between quality articulation and trial factors, with boundaries consolidated to address the exploration premium; second, utilize least-squares and assessing condition methods to gauge boundaries and their relating standard blunders; third, register test insights, P-qualities and NFD as proportions of factual criticalness. The benefits of this methodology are as per the following. To begin with, it tends to the exploration interest in a particular, precise way, and maximally uses all the information and other important data. Second, it represents both orderly and irregular varieties related with the information, and the consequences of such examination give not just quality explicit data applicable to the exploration objective, yet additionally its dependability, in this way helping agents to settle on better choices for subsequent investigations. Third, this methodology is truly adaptable, and can undoubtedly be stretched out to different sorts of MTC considers or other microarray explores by detailing various models dependent on the test plan of the investigations.

Unmanned aerial vehicles (UAVs)-based communication system is a promising solution to meet coverage and capacity requirements of future wireless networks. However, UAV-enabled communications is constrained with its coverage, energy consumption, and flying regulations, and the number of works focusing on the sustainability aspect of UAV-assisted networking has been limited in the literature so far. In this paper, we propose a solution to this limitation; particularly, we design a $Q$-learning-based UAV positioning scheme for sustainable wireless connectivity considering key constraints, that are, altitude regulations, non-flight zones, and transmit power. The objective is to find the optimal position of the UAV base station (BS) and minimize the energy consumption while maximizing the number of users covered. Moreover, a weighting mechanism is developed, where the energy consumption and number of users covered can be prioritized according to network/battery conditions. The proposed Q-learning-based solution is compared to the baseline k-means clustering method, where the UAV BS is positioned at the centroid location that minimizes the cumulative distance between the UAV BS and the users. The results demonstrate that the proposed solution outperforms the baseline k-means clustering-based method in terms of the number of users covered while achieving the desired minimization of the energy consumption.

As a part of the proposed article, the authors presented comprehensive data analysis for movement data that comes from a positioning system based on ultra-wide band (UWB) technology. For purpose of this article, a test was carried out during which the car equipped with cruise control overcame the given path at a speed from 10 km/h to 60 km/h. The obtained motion models (information about position) have been filtered through a series of filters - from fundamentals filters with a variable window (median, moving average, Savitzky-Golay filter), through more complex ones like the Wiener or Kalman filter. As a result, the authors proposed a form of data analysis and filtration depending on the speed of the moving object. In addition, the maximum accuracy that can be obtained for a given traffic model was also determined. The whole research proves that it is possible to use a system based on UWB technology in positioning objects for urban applications - smart city, in industry 4.0 applications as well as for positioning autonomous vehicles in urban applications, such as well as on highways to maintain cohesion of convoys vehicles.

Fusing data from many sources helps to achieve higher results of analysis. In this work, we present a new algorithm to fuse data from multiple cameras with data from multiple lidars. This algorithm was developed to increase the sensitivity and specificity of autonomous vehicle perception systems, where the most accurate sensors measuring the vehicle’s surroundings are cameras and lidar devices. Perception systems based on data from one type of sensor do not use complete information and have lower quality. The camera provides two-dimensional images; lidar produces three-dimensional point clouds. We developed a method for matching pixels on a pair of stereoscopic images using dynamic programming inspired by an algorithm to match sequences of amino acids used in bioinformatics. We improve the quality of the basic algorithm using additional data from edge detectors. We also improve the algorithm performance by reducing the size of matched pixels determined by available car speeds. We perform point cloud densification in the final step of our method, fusing lidar output data with stereovision output. We implemented our algorithm in C++ with Python API, and we provided the open-source library named Stereo PCD. This library very efficiently fuses data from multiple cameras and multiple lidars. In the article, we present the results of our approach to benchmark databases in terms of quality and performance. We compare our algorithm with other popular methods.