In the present work report, the MgAl₂O₄and the Ag/MgAl₂O₄ samples were successfully synthesized by the modified hydrothermal and the isovolumetric impregnation methods, respectively. The structural properties of the prepared samples were systematically characterized by XRD, SEM, TEM, DRS, XPS and et al techniques. The photocatalytic degradation of methylene blue by the Ag/MgAl₂O₄ and MgAl₂O₄ samples was comparatively studied under UV lamp irradiation. The results revealed that the prepared Ag/MgAl₂O₄ (pH=6) samples were the most active among the samples in photocatalytic of methylene blue. Under UV lamp irradiation, the Ag/MgAl₂O₄ (pH=6) photodegradation of methylene blue reached to 89.6% within 120 min. And the Ag/MgAl₂O₄ (pH=6) complex photocatalysts displayed a high photochemical stability under repeated irradiation. Repeated irradiate the Ag/MgAl₂O₄ (pH=6) compound, which indicated it had a high photochemical stability.

Abstract: Development of the fast neutron radiography with higher penetration capability in Non-Destructive Testing (NDT) techniques is rapidly. The detection efficiency and the imaging spatial resolution are the main problem of the radiography detector for many fast neutron imaging systems. In this paper, a detector composed of pixelated EJ200 scintillator array，an 16 × 16 silicon-photomultipliers (SiPM) array, and a capacitive multiplexing network readout electronics is designed. Using Monte-Carlo simulations，the main parameters of the detector was optimization. Then the detector prototype was fabricated and tested at a 14 MeV D-T neutron source. The preliminary test results showed that the prototype has spatial resolution of 1.26 mm. Using pixelated scintillator structure，the conflict between spatial resolution and detect efficiency could improved. Moreover, SiPMs offer a flexibility for the expansion of application field of the imaging system due to their excellent photon detection performance, relatively low price and joint possibility for large area.

The lithium-ion batteries are widely used as a power source for portable devices, including cell phones. The useful life is about 2 years or 500 cycles, contributing to the generation of waste from electrical and electronic equipment (WEEE). Mining of lithium and cobalt damages the environment and is onerous; therefore, sustainable alternatives, such as obtaining these elements from secondary sources as recycling of lithium-ion batteries, are essential to provide the inputs used in the sector. However, the metallurgical route which will used to recovering them must be considered, due to this work aims for a more environmentally favorable process using DL-malic acid 1.5 M and instead of compared with sulfuric acid 2 M, heat pretreatment of 1 h and 3 h, and for all conditions, experiments were carried out with and without adding the oxidizing agent hydrogen peroxide. The best yields occurred in presence of H2O2 10 % v/v, and heat pretreatment of 1 h: 33.49 % Co and 4.63 % Li, and 29.78 % Co e 3.44 % Li were recovered by sulfuric acid and DL-malic acid, respectively.

Epithelial–mesenchymal transition (EMT) is defined as a cellular process during which epithelial cells acquire mesenchymal phenotypes and behavior following the downregulation of epithelial features. EMT and its reversed process, the mesenchymal-epithelial transition (MET), and the special form of EMT, the endothelial-mesenchymal transition (EndMT), have been thought as a universal dogma controlling developmental and pathological processes. More than half a century of EMT study has made it a large research field and a mainstream concept. However, discrepancies and disputes over EMT and EMT research have also grown over time. Particularly, neither the epithelial and mesenchymal states/properties nor their regulatory networks nor specific markers have been defined, rendering the EMT, MET and EndMT concepts groundless. Moreover, EMT and MET effects should not be a cause, but rather a consequence of or an accompanying effect during developmental and pathological processes. EMT and MET represented by the change in cell shapes or adhesiveness or symbolized by EMT factors are biased interpretation of the overall change in cellular property and regulatory networks during development and cancer progression. The true meaning of EMT effects in some developmental and pathological processes, such as fibrosis, needs re-evaluation. But the core EMT factors are actually a few components of the regulatory networks of neural stemness, which determines tumorigenicity and pluripotency. The EMT effects in cancer progression and neural crest formation are wrong attribution of the role of neural stemness during cancer progression and the cell-intrinsic property of neural crest cells to the unknown mesenchymal state. It is time to reassess the significance of EMT and its related concepts in scientific research.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

Flavonoids are secondary plant metabolites involved in biological activity that are present in plentiful proportions in many plant origin foods and beverages. Owing to their chemical difference and qualities that make them beneficial for human health, they have received a lot of focus in research. This review therefore presents an account on the chemical structure of flavonoids, food sources and their metabolism with emphasis on bioavailability. And they also examine their antioxidant, anti-inflammatory, anticancer, cardiovascular protective, neuroprotective, and antimicrobial properties and reveal related molecular processes. In addition, it overviews the clinical data concerning their possible use in the prevention and treatment of chronic diseases. Some of the problems that attend current flavonoid research are also dealt with; such issues as variation in the bioactivity of flavonoids and scarcity of clinical studies. This review is designed to present current state of knowledge and to provoke further research concerning the further potential of flavonoids in enhancing human health.

Solanum indicum Linn, is commonly known as Indian Nightshade or Poison Berry belongs to the family Solanaceae. This review studied the botanical description, traditional uses of its seeds, its chemical composition, pharmacological properties and modern applications in medicinal system. The plant is rich in alkaloids, steroidal saponins, flavonoids and phenolic acids having diverse pharmacological activities and phytochemical profile. It is used in treatment of various respiratory disorders, inflammation, skin problems and gastrointestinal disease since ancient times. Scientific research in modern times also tested many of the traditional uses revealing anti-inflammatory, antioxidant, antimicrobial activities as well as some cytotoxic and even antidiabetic effects. These pharmacological activities show potential future as uses for organic drugs, natural health products, skincare formulations and agricultural advancements.

The applicability of the distance aggregation problem has attracted the interest of many authors. Motivated by this fact, in this paper we face the modular quasi-(pseudo-)metric aggregation problem. We characterize those functions that allow merging a collection of modular quasi-(pseudo-)metrics into a single one. Specifically, a description of such functions in terms of triangle triplets is given and, in addition, the relationship between modular quasi-(pseudo-)metric aggregation functions and modular (pseudo-)metric aggregation functions is discussed. Such characterizations are illustrated with appropriate examples. A few methods to construct modular quasi-(pseudo-)metrics are yielded. Several properties of modular quasi-(pseudo-)metric aggregation functions are explored and used to develop quick tests for discarding candidate functions to aggregate modular quasi-(pseudo-)metrics. Moreover, a characterization of those modular quasi-(pseudo-)metric aggregation functions that preserve modular quasi-(pseudo-)metrics is also provided. Furthermore, the relationship between modular quasi-(pseudo-)metric aggregation functions and quasi-(pseudo-)metric aggregation functions is studied in such a way that significative differences are displayed.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

In this paper, we investigate the effects of certain variants of the commutative laws on properties of several families of algebras which are in general not commutative, such as groups, linear algebras, or actually quite anti-commutative, such as $BCK$-algebras and $d$-algebras among others. From results obtained it becomes clear that by considering these variants in the presence of yet other axioms it is to be expected that a quite rich and varied set of results may be obtained both in the general and the particular setting of which what has been accomplished in this paper is a substantial sample.

It is known that the source of a tectonic earthquake in the framework of the theory of elasticity and viscoelasticity is considered as a displacement along a certain fault surface. Usually, when describing the source, the geometry of the fault surface is simplified to a flat rectangular area. The displacement vector is assumed to be constant. In this paper, we propose a model of an earthquake source in the form of a displacement with a constant vector along a stochastic surface. A number of standard assumptions were made when modeling. We take into account only the elastic properties of the medium. We consider the Earth’s crust as a half-space and assume that the medium is homogeneous and isotropic. For the mathematical description of the earthquake source, we use the classical force equivalent of displacement along the fault. This is the distribution of double pairs of forces. The field of displacements under the action of body forces is found through a combination of Mindlin nuclei of strain. The paper presents solutions for strike-slip fault. To obtain a stochastic fault surface, we propose to introduce a random deformation of a rectangular flat surface. The paper presents the results of a computational experiment comparing the levels and regions of relative deformations of the Earth’s crust in the case of displacement along a flat rupture surface and along a stochastic one. In the case of a stochastic surface, the regions of relative deformations become asymmetric. The developed model will help to indirectly take into account various mechanical properties of the Earth’s crust when modeling deformations caused by earthquakes.

Generative models for images, audio, text and other low-dimension data have achieved great success in recent years. Generating artificial human movements can also be useful for many applications, including improvement of data augmentation methods for human gesture recognition. The object of this research is to develop a generative model for skeletal human movement, allowing to control the action type of generated motion while keeping the authenticity of the result and the natural style variability of gesture execution. We propose to use a conditional Deep Convolutional Generative Adversarial Network (DC-GAN) applied to pseudo-images representing skeletal pose sequences using Tree Structure Skeleton Image format. We evaluate our approach on the 3D-skeleton data provided in the large NTU RGB+D public dataset. Our generative model can output qualitatively correct skeletal human movements for any of its 60 action classes. We also quantitatively evaluate the performance of our model by computing Frechet Inception Distances, which shows strong correlation to human judgement. Up to our knowledge, our work is the first successful class-conditioned generative model for human skeletal motions based on pseudo-image representation of skeletal pose sequences.

Soft magnetic composites cores were produced by Spark Plasma Sintering (SPS) from Ni3Fe@ZnFe2O4 and NiFeMo@ZnFe2O4 pseudo-core-shell powders. In the Fe-Ni alloys@ZnFe2O4 pseudo-core-shell composite powders, the core is a large nanocrystalline Permalloy or Supermalloy particle obtained by mechanical alloying, and the shell is a pseudo continuously layer of Zn ferrite particles. The pseudo-core-shell powders have been compacted by SPS at temperatures between 500-700 ºC, with a holding time of 0 minutes. Several techniques were used for the characterisation of the powders and sintered compacts: X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, magnetic hysteresis measurements (DC and AC) and electrical resistivity. The electrical resistivity is stabilised at values of about 7·10-3 Ω·m for sintering temperatures between 600-700 °C and this value is 3 orders of magnitude higher than the electrical resistivity of sintered Fe compacts. The best relative initial permeability was obtained for the Supermalloy/ZnFe2O4 composite compacts sintered at 600 ºC, which decreases linearly for the entire frequency range studied, from around 95 to 50. Up a frequency of 2,000 Hz the power losses are lower than 1.5 W/kg. At the frequency of 10 kHz, the power losses are larger, but they remain at a low level. In the case of Supermalloy/ZnFe2O4 composite compact SPS-ed at 700 °C, the specific power losses are even lower than 5 W/kg. The power losses decomposition proved that intra-particles losses give the main part of the losses.

The art of representing source code is pivotal in numerous programming analysis applications. Recent strides in neural networks have marked notable successes in this realm. However, the peculiar structural characteristics inherent in programming languages have not been fully exploited in existing models. While neural models based on abstract syntax trees (ASTs) adeptly manage the tree-like nature of source codes, they fall short in discerning the diverse substructural nuances within programs. This paper introduces the Dynamic Syntax Tree Model (DSTM), an innovative approach that fuses various neural network modules into tree architectures tailored to the specific AST of the input. Distinct from preceding tree-based neural models, DSTM adeptly discerns the semantic variances across different AST substructures. We validate DSTM through rigorous testing in program classification and code clone detection, outperforming contemporary methods and demonstrating the benefits of harnessing intricate source code structures.

The original purpose of this article was to modify the original SIR equations to allow for a direct source of infection (without which the original equations would have no solutions unless one starts with an already infected population) and also to see to what extent one could obtain multiple outbreaks of an infectious disease. In the course of developing the basic ideas several other factors arose to take prominent roles.Perhaps one of the more salient factors is the point that choosing an arbitrary time to change conditions from say a lock-down for the population to a less stringent social behavior, such as allowing partial or complete opening of businesses and schools, etc. should be based on knowledge of the disease and its evolution. Such decisions are usually made by politicians who have less than full information concerning the consequences of their actions. Several examples are given to illustrate these points.

This study provides a comprehensive analysis of the conformational dynamics of pseudo-endocannabinoid receptors (p-CBRs) CB₁ and CB₂ in response to ligand binding. The ligands studied include N-arachidonoyl dopamine (NADA), Cannabidiol (CBD), known agonists (FUB-MDMB and E3R), and inverse agonists (Taranabant and AM630). Using homology models based on crystal structures (PDB ID: 5U09 for CB₁ and 5ZTY for CB₂), molecular docking, and molecular dynamics (MD) simulations, the research validates the structural integrity and dynamic behaviours of these pseudo-receptors. Induced-fit docking revealed NADA as having the highest binding affinity for both receptors, with docking scores of −13.92 kcal/mol for CB₁ and −13.32 kcal/mol for CB₂, facilitated by key hydrogen bond interactions. MD simulations over 250 ns at ~298 K showed successful equilibration, indicating the most stable interaction for NADA, thereby further validating the models. CB₁ and CB₂ exhibited distinct conformational responses to ligands, with Cα RMSD and Cα RMSF analyses suggesting a more rigid binding pocket for CB₁ and a flexible binding pocket for CB₂. These findings highlight the significance of receptor behaviour and dynamics in the development of cannabinoid-based therapeutics, supporting the potential of CBD and NADA as modulators for CB₁ and CB₂, respectively.

The Source Region of the Yellow River (SRYR), renowned as the "Water Tower of the Yellow River", serves as an important water conservation domain in the upper reaches of the Yellow River, significantly influencing water resources within the basin. Based on the Weather Research and Forecasting (WRF) Model Hydrological modeling system (WRF-Hydro) model, the key variables of the atmosphere-land-hydrology coupling processes over the SRYR during the 2013 rainy season are analyzed. The investigation involves a comparative analysis between the coupled WRF-Hydro and the standalone WRF simulations, focusing on the hydrological response to the atmosphere. The results reveal that the WRF-Hydro model's proficiency in depicting streamflow variations over the SRYR, yielding a Nash Efficiency Coefficient (NSE) of 0.44 and of  0.61 during the calibration and validation periods, respectively. Compared to the standalone WRF simulations, the coupled WRF-Hydro model demonstrates enhanced performance in soil heat fluxes simulations, reducing the mean Root Mean Square Error (RMSE) of surface soil temperature by 0.96 K and soil moisture by 0.01 m\textsuperscript{\textsuperscript{3}}/m\textsuperscript{\textsuperscript{3}}. Furthermore, the coupled model adeptly captures the streamflow variation characteristics with the NSE of 0.33. This underscores the significant potential of the coupled WRF-Hydro model for delineating coupled atmosphere-land-hydrology processes in regions characterized by cold climates and intricate topography.

Reliable and precise damage localization in mechanical structures is of high importance in the context of structural health monitoring (SHM). The acoustic emission (AE) method has already shown its excellent suitability for damage localization. However, low signal-to-noise ratios (SNRs) are often prevalent in SHM, thus an increase in localization accuracy and robustness is still in demand. The present study faces this task through the integration of various model knowledge for AE source localization. The basis of the presented algorithm is the consideration of the dispersive behavior of elastic waves in thin-walled structures. The continuous wavelet transform (CWT) is used to obtain time-frequency representations of the signals, where frequency-dependent values for time-of-arrival (TOA) are extracted. Furthermore, the algorithm incorporates the knowledge that all sensors receive signals with the same time and location of origin, as well as the slightly different sensitivity of the theoretically equal sensors. The final localization results are achieved by a two-parameter grid search optimization. The algorithm is experimentally tested on a large aluminum plate with four piezoelectric wafer active sensors (PWASs) arranged in an array of 100 mm × 100 mm. The mean localization error of pencil lead breaks at ten different positions within the sensor array is used as an accuracy measure. It is shown that as more of the described model knowledge is incorporated into the localization, the accuracy increases. With the final algorithm, the mean localization error is more than halved compared to AE localization based on classical TOA estimation. Although the experiment described is conducted under laboratory conditions, the remarkable increase in accuracy suggests that AE source localization may be successful even at low SNR as typical for operational conditions.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Our method for density elimination is generalized to the non-commutative substructural logic GpsUL∗. Then the standard completeness of HpsUL∗follows as a lemma by virtue of previous workbyMetcalfeandMontagna. This result shows that HpsUL∗ is the logic of pseudo-uninorms and their residua and answered the question posed by Prof. Metcalfe, Olivetti, Gabbay and Tsinakis.

The star matter composed of nucleons deep inside the compact star like a neutron star is believed to be very dense and various new types of concepts and physical phenomena due to the nontrivial strong correlations are naturally expected. Peudo-conformality in dense star matter has been discussed recently assuming the hidden underlying scale symmetry, which is partly supported by the recent discussions of infrared conformal window of QCD. It is found that the appearance of dilaton and the dilatonic mean field calculation of nucleonic matter lead to the density independent nucleon mass at higher density regime than normal nuclear matter density. Non-vanishing constant nucleon mass can be considered as a chiral invariant mass of the parity doublet model, in which the chiral symmetry is manifested even in the massive nucleon sector provided with a parity doubling. In this paper we will discuss how the chiral and scale symmetry are correlated to lead the parity doublet symmetry inside the core of the compact star. A simple schematic model is adopted. The star matter at T=0 is basically composed of the nucleons. As a first approximation, they can be treated as free fermions with the effective mass filled up to fermi surface. There is a nontrivial feature due to the interplay between vector meson and nucleon(or equivalently dilaton, χ). The trace of energy momentum tensor approaches density independent, the pseudo-conformal phase. Local fluctuations inside the star matter will be travelling with the speed of sound which depends on the equation of state. In the pseudo-conformal phase, the speed of sound approaches to the conformal velocity for the scale symmetric matter, vc=13c. The excitations of the parity doublets in the compact star matter as an emerging phenomena in pseudo-conformal phase will be discussed in connection to the chiral symmetry. The possible implication on the corespondence of hadrons to quark degrees of freedom will be briefly discussed.

Incorporating source-side linguistic knowledge into the neural machine translation (NMT) model has recently achieved impressive performance on machine translation tasks. One popular method is to generalize the word embedding layer of the encoder to encode each word and its linguistic features. The other method is to change the architecture of the encoder to encode syntactic information. However, the former cannot explicitly balance the contribution from the word and its linguistic features. The latter cannot flexibly utilize various types of linguistic information. Focusing on the above issues, this paper proposes a novel NMT approach that models the words in parallel to the linguistic knowledge by using two separate encoders. Compared with the single encoder based NMT model, the proposed approach additionally employs the knowledge-based encoder to specially encode linguistic features. Moreover, it shares parameters across encoders to enhance the model representation ability of the source-side language. Extensive experiments show that the approach achieves significant improvements of up to 2.4 and 1.1 BLEU points on Turkish→English and English→Turkish machine translation tasks, respectively, which indicates that it is capable of better utilizing the external linguistic knowledge and effective improving the machine translation quality.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

Background: Extra virgin olive oil is a fundamental component of the Mediterranean diet. It contains several molecules that sustain human well-being by modulating cellular metabolism and exerting antioxidant, anti-inflammatory, anti-ageing effects to protect normal tissues and can exert anti-angiogenic, and pro-apoptotic effects on cancer cells. Metabolites found in different parts of the olive tree, including leaves, also possess properties that might help in cancer prevention and promote wellness in aging. Olive mill wastewater (OMWW), a liquid residue produced during olive oil extraction, represents an environmental issue. However, it is enriched in phytochemicals with potential beneficial properties. Dietary supplements based on OMWW can be produced for nutritional supplementation with advantages to the ecology. Purpose: This work aims to measure hematochemical, anthropometric and metabolomic parameters in volunteers assuming an OMWW dietary supplement, OliphenoliaⓇ (OMWW-OL). Methods: The supplementation of OMWW-OL 25 mL twice daily for 30 days was tested on a pilot cohort of volunteers with characteristics close to metabolic syndrome. Hematochemical, anthropometric, and metabolomic parameters were analyzed before the intervention, at 30 days and 30 days after stopping consumption. Results: 29 volunteers were enrolled and 23 completed the study. The participants’ parameters at baseline were measured, and then twice daily at 30 days of treatment and 30 days after assumption discontinuation. Although treatment was with an olive derivative, weight and body mass index instead of increasing slightly decreased, particularly in women. Also, hydration increased, especially in women, while blood pressure, glycemia and insulin decreased. Cholesterol, low-density and high-density lipoproteins and triglycerides were stable while vitamin D levels, alongside calcium, sensibly increased. Albumin also increased and parameters related to sarcopenia displayed promising, although not statistically significant, trends toward positive effects. All the values were in support of an equilibrium with no damaging effects. By mass spectrometry analysis, we also found favorable changes in the vitamin D/histamine and homocysteine/methionine ratios, an increase in a new metabolite of unknown formula, and vitamin D/unknown metabolite ratio. Conclusions: Supplementation of OMWW-OL has no detrimental effects and, although with limited potency of a pilot study, might imply the beneficial modulation of several biological parameters, being potentially valuable for people at risk of metabolic syndrome. Some of these parameters could also be relevant as anti-ageing and in cancer prevention.

An approach to the assessment of probabilistic inference is described which quantifies the performance on the probability scale. From both information and Bayesian theory, the central tendency of an inference is proven to be the geometric mean of the probabilities reported for the actual outcome and is referred to as the “Accuracy.” Upper and lower error bars on the accuracy are provided by the arithmetic mean and the -2/3 mean. The arithmetic is called the “Decisiveness” due to its similarity with the cost of a decision and the -2/3 mean is called the “Robustness”, due to its sensitivity to outlier errors. Visualization of inference performance is facilitated by plotting the reported model probabilities versus the histogram calculated source probabilities. The visualization of the calibration between model and source is summarized on both axes by the arithmetic, geometric, and -2/3 means. From information theory, the performance of the inference is related to the cross-entropy between the model and source distribution. Just as cross-entropy is the sum of the entropy and the divergence; the accuracy of a model can be decomposed into a component due to the source uncertainty and the divergence between the source and model. Translated to the probability domain these quantities are plotted as the average model probability versus the average source probability. The divergence probability is the average model probability divided by the average source probability. When an inference is over/under-confident, the arithmetic mean of the model increases/decreases, while the -2/3 mean decreases/increases, respectively.

We report on recent experimental results on β decay into self-conjugate (N=Z) nuclei with mass number 58≤A≤70. Super-allowed β decays from the Jπ=0+ ground state of a Z=N+2 parent nucleus are to the isobaric analogue state, through so-called Fermi transitions, and to Jπ=1+ states, by way of Gamow–Teller (GT) transitions. The operator of the latter decay is a generator of Wigner’s SU(4) algebra and as a consequence GT transitions obey selection rules associated with this symmetry. Since SU(4) is progressively broken with increasing A, mainly as a consequence of the spin–orbit interaction, this symmetry is not relevant for the nuclei considered here. We argue, however, that the pseudo-spin–orbit splitting can be small in nuclei with 58≤A≤70, in which case nuclear states exhibit an approximate pseudo-SU(4) symmetry. To test this conjecture, GT decay strength is calculated with use of a schematic Hamiltonian with pseudo-SU(4) symmetry. Some generic features of the GT β decay due to pseudo-SU(4) symmetry are pointed out. The experimentally observed GT strength indicates a restoration of pseudo-SU(4) symmetry for A=70.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

Part II, like Part I, discusses geometry, kinematics and statics in detail without taking into account power losses in meshing. The main goal of Part II, however, is to prove that there are complex and structurally coupled planetary gear systems, i.e. containing a closed circuit in which no circulation of power flow is generated. The power flow analysis is also carried out using the direct method, with a slight modification in the way of writing the equations identifying active and passive gears, i.e. at the same time the directions of power flow on all transmission paths. The analysed planetary gear system (PGS) is characterised by mobility equal to 1, i.e. single degree of freedom (DoF). It consists of three subsystems in the form of the 2KH type planetary units connected in series-parallel, specially selected to demonstrate the thesis of this paper. It consists of three subsystems in the form of single planetary subsystems of the 2KH type connected series-parallel, specially chosen to illustrate the thesis of this paper.

The rapidly evolving field of artificial intelligence (AI) continues to witness the introduction of innovative open-source pre-trained models, fostering advancements in various applications. One such model is Llama 2, an open-source pre-trained model released by Meta, which has garnered significant attention among early adopters. In addition to exploring the foundational elements of the Llama v2 model, this paper investigates how these early adopters leverage the capabilities of Llama 2 in their AI projects. Through a qualitative study, we delve into the perspectives, experiences, and strategies employed by early adopters to leverage Llama 2's capabilities. For the purpose of data analysis, the capabilities inherent in the Llama 2 model were employed to conduct keyword extraction from the context of the early adopters' case studies. The findings shed light on the model's strengths, weaknesses, and areas of improvement, offering valuable insights for the AI community and Meta to enhance future model iterations. Additionally, we discuss the implications of Llama 2's adoption on the broader open-source AI landscape, addressing challenges and opportunities for developers and researchers in the pursuit of cutting-edge AI solutions. The present study constitutes an early exploration of the Llama 2 pre-trained model, holding promise as a foundational basis for forthcoming research investigations.

The atomic structures of Zn and Na borophosphate glasses were studied by X-ray and neutron diffraction. Peaks assigned to the B−O, P−O, and O−O distances confirm that only BO4 units co-exist with the PO4 tetrahedra. The Zn−O and Na−O coordination numbers are found to be a little larger than four. The narrowest peaks of the Zn−O first-neighbor distances exist for the glasses along a line connecting the Zn(PO3)2 and BPO4 compositions (50 mol% P2O5) which is explained by networks of ZnO4, BO4, and PO4 tetrahedra with twofold coordinated oxygens. Calculated amounts of the available oxygen support this interpretation. Broadened peaks occur for glasses with lower P2O5 contents, consistent with the presence of threefold coordinated oxygens. The two distinct P−O peak components of the Zn and Na borophosphate glasses differ in their relative abundances which is interpreted by Na+ cations that coordinate oxygens in some P−O−B bridges, something not seen for the Zn2+ ions.

Agrivoltaic agrotunnels are currently designed for high density grow walls that are not amenable to bush berries or root crops. Commercial grow bins provide deeper substrates for produce with more root systems but have high costs per unit growing area. To overcome the economic limitations of grow bins, this study applies the distributed manufacturing open-source design paradigm to develop four designs for low-cost open source structures. The designs target root vegetables and bush fruit specifically to be adopted by remote communities with limited or no outdoor growing environment to offset the market price for imported fresh produce. The indoor growing designs provide the necessary structure for supporting grow light and grow bins and enabled the transplanted berry plants to flower and produced fruits. They provide a comparable amount (110L) or more of grow volume from 106 to 192 L. The water reservoir volume for the commercial system (62 L) and grow area (0.5 m³) is surpassed by all new designs that range from 64 to 192 L and 0.51 to 0.76 m³, respectively. These superior properties are possible with material costs for all four designs that save more than 90% of the economic cost of the commercial systems.

Macrophages as a source and target of GDF-15

After 2010, the source model of the microSelectron HDR Afterloader System was slightly modified from the previous model. Granero et al. named the modified source model “mHDR-v2r (revised model mHDR-v2)” and the previous model “mHDR-v2”. They concluded that the dosimetric differences arising from the dimensional changes between the mHDR-v2 and mHDR-v2r designs were negligible at almost all locations (within 0.5 % for r ≥ 0.25 cm), the two-dimensional anisotropy function difference between the two sources is found 2.1 % at r = 1.0 cm when compared with the results of the other experimental group. To confirm this difference, we performed a full Monte Carlo simulation without the energy fluence approximation. This is useful near the radiation source where charged-particle equilibrium does not hold. The two-dimensional anisotropy function of the TG-43U1 dataset showed a few percent difference between the mHDR-v2r and mHDR-v2 sources. There was no agreement in the immediate vicinity from the source (0.10 cm and 0.25 cm), when compared to Granero et al. in mHDR-v2r sources. The differences in these two-dimensional anisotropy functions were identified.

We suppose that vacuum is filled with a kind of continuously distributed matter which may be called the $\Omega(1)$ substratum, or the electromagnetic aether. Suppose that the time scale of a macroscopic observer is very large compares to the the Maxwelllian relaxation time of the $\Omega(1)$ substratum. Thus, the macroscopic observer concludes that the $\Omega(1)$ substratum behaves like a Newtonian-fluid. Inspired by H. A. Lorentz, we speculate that electric charges may be extremely small hard spherical sources or spherical sinks with finite radii. Based on the spherical source and spherical sink model of electric charges, we derive Coulomb's law of interactions between static electric charges in vacuum. Further, we derive a reduced form of the Lorentz's force law for static electric charges in vacuum.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

Initial periods of adsorption kinetics play an important role in estimating the initial adsorption rate and rate constant of adsorption process. Several adsorption processes rapidly occur, and the experimental data of adsorption kinetics under the initial periods can contain potential errors. The pseudo-second-order (PSO) kinetic model has been popularly applied in the field of adsorption. The use of the nonlinear optimization method to obtain the parameters of the PSO model can minimize error functions during modelling compared to the linear method. However, the nonlinear method has limitations in that it cannot directly recognize potential errors in the experimental points of time-dependent adsorption, especially under the initial periods. In this study, for the first time, the different linear types (Types 1–6) of the PSO model are applied to discover the error points under the initial periods. The result indicated that the fitting method using its linear equations (Types 2–5) is really helpful for identifying the error (doubtful) experimental points from the initial periods of adsorption kinetics. The imprecise points lead to low adjusted R2 (adj-R2), high reduced χ2 (red-χ2), and high Bayesian information criterion (BIC) values. After removing those points, the experimental data were adequately fitted with the PSO model. statistical analyses demonstrated that the nonlinear method must be used for modelling the PSO model because its red-χ2 and BIC were lower than the linear method. Type 1 has been extensively applied in the literature because of its very high adj-R2 (0.9999) and its excellent fitting to experimental points. However, its application should be limited because the potential errors from experimental points were not identified by this type. For comparison, the other kinetic models (i.e., pseudo-first-order, pseudo-nth-order, Avrami, and Elovich) are applied. The modelling result using the nonlinear forms of those models indicated that the fault experimental points from the initial periods were not detected.

In this work, the conceptions of the electrodynamics of action-at-a-distance and of electromagnetic fields are reviewed and confronted, with the aim of clarifying whether it is possible to propose a Weberian theory of action-at-a-distance, which together with a renewed mechanics (both re-specting the existence of a limiting velocity c) could constitute a framework capable of yielding predictions equivalent to those of the conventional Maxwell-Lorentz and SRT framework. In this work, it is shown that, considering basic assumptions about the interaction process, understanding it as an action exchange process, it is possible to derive the expression of the electrodynamic Phipps’ potential energy between two interacting charges. It is also shown that, with the same assumptions and the additional hypothesis that the interaction is supported by a mediating agent (aether or field) which is perturbed by the transmission of action, this perturbation obeys the wave equation (one of the main drawbacks of Weberian electrodynamics). Another aim of the work is to confront the relational electrodynamic formulations (supported by Galilean transformations that assume a universal time) with the Maxwell-Lorentz formulation of electromagnetism (linked to Lorentz transformations that entail local times), in order to elucidate whether the space-time to which the SRT leads us is a mere mathematical artifice or an inescapable reality.

New ways of generating energy are currently being discussed, with a transition from traditional primary sources to more environmentally friendly options, particularly renewables. Energy storage is also closely related to this transition. Battery storage currently dominates this area. However, flywheel energy storage system (FESS) technology offers an alternative that uses stored kinetic energy to be transformed into mechanical energy and, using a motor-generator, electrical energy. FESS technology is thus flexible and can be applied in different industrial applications. The management of the technology of recycling W-MMC waste material from other products and the subsequent trial production of high-strength W-MMC material with a density of more than 17 500 kg/m3 from recycled powders allowed to test the limits of the so-called "heavy" flywheels used in rotor production. Materials with densities ≥ 7 800 kg/m3, and operating at lower to medium speeds up to 20 000 rpm. The results achieved lead to the conclusion that the developed recycled materials of the W-MMC type with a density ≥ 17 500 kg/m3, with a yield strength of 1 200 - 1 700 MPa depending on the production method, can be used as a substitute for the structural steels used today, without an enforced reduction of the maximum allowed rotor speed due to exceeding the maximum allowed stress.

In 2020, the Covid-19 outbreak led many countries across the globe to introduce lockdowns (LDs) that effectively caused most anthropic activities to either stop completely or be significantly reduced. In Europe, Italy played a pioneeristic role via the early introduction of a strict nationwide LD on March 9^th. This study is aimed at evaluating, using both chemical and meteorological data, the environmental response to that occurrence as observed by the Lamezia Terme (LMT) GAW/WMO station in Calabria, Southern Italy. The first 2020 lockdown has therefore been used as a “proving ground” to assess CO, CO₂, CH₄, BC, and NO_x concentrations in a rather unique context by exploiting the location of LMT in the context of the Mediterranean Basin. In fact, its location on the Tyrrhenian coast of Calabria and local wind circulation both lead to daily cycles where western-seaside winds depleted in anthropogenic pollutants can be easily differentiated from northeastern-continental winds, enriched in anthropogenic outputs. In addition to that, the first Italian LD occurred during the seasonal transition from Winter to Spring and, consequently, Summer, thus providing new insights on emission outputs correlated with seasons. Findings have clearly indicated BC and, in particular, CO as strongly correlated with average daily temperatures, and possibly domestic heating. CO₂’s reduction during the lockdown and consequent increase in the post-lockdown period, combined with wind data, has allowed to constrain local source of emissions located northeast from LMT. NO_x reductions during specific circumstances are consistent with hypotheses from previous research which linked them to rush hour traffic and other forms of transportation emissions. CH₄’s stable patterns are consistent with livestock, landfills, and other sources assumed to be nearly constant during LD periods.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

A pivotal strategy in decarbonizing the transport sector is by transitioning from internal combustion engine vehicles (ICEVs) to electric vehicles (EVs), especially if they are charged with renewable energy. To provide an incentive to the common populace to switch to EVs, cities should set up - or enable or even encourage the private sector to do so - electric vehicle charging stations (EVCS) at multiple and suitably accessible locations. This paper aims to present a digitaltwin-enabled methodology study for selecting the most suitable possible locations to establish EVCS with consideration of the low voltage (LV) network operation in terms of power losses, active and reactive power in EV charging demand and the effect of the EVCS on the transformers, based on examples in Newcastle upon Tyne (England, UK). It also evaluates the most suitable type of charger that could be installed at these locations by studying the estimated traffic, cost and impact of the EVCS on the power grid, both at peak and off hours. This paper demonstrates how digitaltwin technologies, such as the web-based tool AutoDesign by Northern Powergrid and EA Technology and open source Pandapower can be used for identifying the most viable and cost-effective locations to connect EVCSs to a Distribution Network Operators (DNO)’s LV network. The results of the analysis indicate that with the installation of the most suitable type of EVCS in a particular location, the local power grid would not be significantly affected at any hour of the day.

Additives for anaerobic digestion (AD) can play a significant role in optimising the process by increasing biogas production, stabilising the system and improving digestate quality. The role of additives largely boils down to: (i) enhancing direct interspecies electron transfer (DIET) between microbial communities, resulting in improved syntrophic interactions and methane production rates (e.g. biochar, magnetite and carbon nanotubes), (ii) adsorption of toxic substances that may inhibit microbial activity (e.g. activated carbon, zeolites), (iii) improving microbial activity and increasing process stability (e.g. cobalt, nickel, iron, selenium), (iv) maintaining optimal pH levels for microbial activity (e.g. magnesium oxide), (v) reducing inhibition (the aforementioned adsorbents and conductive substances), (vi) accelerating the decomposition of complex organic materials into simpler compounds that are more easily digested by microorganisms, thereby increasing the rate of hydrolysis (enzymes, including cellulases, proteases and lipases). Through the aforementioned action, additives can significantly affect AD performance. The function of these materials varies, from enhancing microbial activity to maintaining optimal conditions and protecting the system from inhibitors. The choice of additives should be carefully tailored to the specific needs and conditions of the digester to maximise benefits and ensure sustainability. In light of these considerations, this paper characterizes the most commonly used additives and their combinations based on a comprehensive review of recent scientific publications, including a report on the results of conducted studies. The publication features chapters that describe: carbon-based conductive materials, metal oxide nanomaterials, trace metal and biological additives, including enzymes and microorganisms. It concludes with a chapter summarising reports on various additives and discussing their indications for functional systems with determined properties. A notable advantage of this work is the updated literature data, clear summaries, and a substantive description of the performance of the additives discussed.

Law of conservation of energy is the most well-established law of modern physics. But, inflationary cosmological model which assumes the universe to be created from a point of singularity has not been able to identify the source of energy for creation of this universe. As per uncertainty principle, a quantum vacuum fluctuation can at most create energy of ~10^-8 kg in a Planck time of ~5.4 ×10^-44 s whereas total positive energy due to matter/vacuum existing in the universe is more than ~10⁵⁴ kg. To solve this problem, we have recently published a new cosmological model (Biswaranjan Dikshit, Canadian Journal of Physics, 100, 218-225, [2022]) in which we have mathematically proved that the total energy of the universe can be zero right from the beginning of the universe to till date due to negative gravitational potential energy and thus law of conservation of energy can be satisfied during creation of the universe from nothing. In this article, starting from a simple argument, we explain why net energy of the universe can be zero only in our model, not in standard cosmological model. An interesting fact pointed out in this paper is that the factor ~10⁶² by which radius of universe has increased from its starting value of ~10^-36 m to present value of ~10²⁶ m is same as the factor by which positive energy has increased from Planck energy ~10^-8 kg to present value ~10⁵⁴ kg. This is in agreement with our new model that predicts the positive energy of universe to be proportional to the radius of universe. We also bring out to the notice that zero energy universe is possible only if smallest possible length in nature is, l_min=l_p(π/2)^1/2 = 2.0×10^-35 m. Minimum possible length is important in theory of quantum gravity and string theory.

Open Inertia Modelling (OpInMod) is a modelling framework designed to create unit commitment and economic inertia dispatch optimisation problems. Present energy system modelling generators do not consider power system inertia in unit commitment and economic dispatch modelling to assess future energy system pathways. However, maintaining sufficient power system inertia in power systems is the foundation for power frequency controllability. The work at hand describes the functionality and approaches of open source tool OpInMod. The softwares universal design approach increases reuse potential. OpInMod is distributed with a set of examples to test and understand OpInMod

Primary Ciliary Dyskinesia (PCD) is a rare genetic disorder characterized by alterations in motile cilia func-tion. The diagnosis of PCD is challenging due to the lack of standardized methods in clinical practice. High-speed video microscopy analysis (HSVA) directly evaluates ciliary beat frequency (CBF) in PCD. Recently, open-source ciliary analysis software applications have shown promise in measuring CBF accurately. How-ever, there is limited knowledge about the performance of different software applications, creating a gap in understanding their comparative effectiveness in measuring CBF in PCD. We compared two open-source software applications, CiliarMove and Cilialyzer, against the manual count method. We used videos rec-orded at high-speed of nasal ciliary brush samples from PCD patients and healthy controls. All three meth-ods showed lower median CBF values in PCD patients than healthy controls. CiliarMove and Cilialyzer identified lower CBF in PCD patients, similar to the manual count. Cilialyzer, CiliarMove and manual count demonstrated statistical significance (p-value < 0.0001) in the difference of median CBF values be-tween PCD and healthy controls. These findings support the utility of open-source software-based analysis tools. Further studies are needed to validate these findings with other genetic variants and identify the op-timal software for accurate CBF measurement in PCD.

One of the most important component of a Geographic Information Retrieval (GIR) is the geoparser, which performs toponym recognition, disambiguation, and geographic coordinate resolution from unstructured text domain. However, news articles which report several events across many place references mentioned in the document is not yet adequately modeled by regular geoparser types where the scope of resolution is either on toponym-level or document-level. The capacity to detect multiple events, geolocate its true locations and coordinates along with their numerical arguments are still missing from modern geoparsers, much less in Indonesian news corpora domain. We propose a novel type event geoparser which integrates an ACE-based event extraction model and provides precise event-level scope resolution. The geoparser casts the geotagging and event extraction as sequence labeling and uses Conditional Random Field with keywords feature obtained using Aggregated Topic Model as a semantic exploration from large corpus, which eventually increases the generalizability of the model. The geoparser also use Smallest Administrative Level feature along with Spatial Minimality-derived algorithm to improve the identification of Pseudo-location entities, resulting 19.4% increase for weighted F1 score. As a side effect of event extraction, the geoparser also extracts various numerical arguments and able to generate thematic choropleth map from a single news story.

This paper explores the role of open-source large language models in IoT cybersecurity world. The threats of malicious activity on the Internet and the loss of private information are very real and lead to serious consequences. The purpose of this paper is to investigate how open source-large language models can help to defend against the growing threat of cyber-crimes. We conducted our experiments in two directions. The first one is a security assistant that helps with cybersecurity best practices advices. The second one is a how large language model can simulate a vulnerable IoT system. For both types of experiments, the interactive mode of operation of the language model is used. In the context of the cybersecurity research, a major advantage of the locally installed open-sourced large language models is that they do not share sensitive data with a remote system in a cloud. The paper concludes by discussing the potential impact of open-source large language models on cybersecurity research and recommends future research directions.

In this paper, based on the pseudo-totem pole (PTP) circuit, a family of five-level PTP dual boost converters (PDBC) is proposed. Dual boost converter has some unique advantages such as no bridge arm shoot-through risk and no switch body diode reverse recovery problem, so that it has a good application prospect. Compared with conventional three-level PTP converters, PDBCs has higher power density, higher efficiency, and low voltage and current stress. The topological derivation process, working principle, modulation and strategy of the topology are analyzed firstly. Further, the number of power devices, the switches voltage and current stress of the proposed topology is analyzed. Finally, a representative five-level PDBC experimental prototype is designed with AC input 220V/50Hz, DC output 400V/1kW, and peak efficiency of 98.27%. The experimental results show that the five-level PDBC proposed in this paper has higher efficiency and verify the correctness of the topology.

Ofloxacin is a highly efficient and widely used antibiotic drug. It is classified as a refractory pollutant due to its poor biodegradability. Consequently, it is commonly found in water sources, requiring efficient methods for its removal. Advanced Oxidation Processes (AOPs) offer efficient alternatives since those yield complete degradation not achieved in adsorption or membrane processes. Previous studies suggest ofloxacin degradation follows a pseudo-first or -second order processes, whereas for full removal of refractory pollutants – lower pseudo-orders are required. Monitoring the actual “pseudo-order” degradation kinetics of ofloxacin is needed to evaluate any proposed AOP process. This study presents a simple procedure to evaluate pseudo-orders of AOPs. Photolysis of 20 mM ofloxacin solutions follow pseudo-zero order kinetics, with half-life times (t_1/2) of approx. 60 min. TiO₂ heterogenous catalyst show to have no influence at low concentration (0.2 mg L^-1) but a significant reduction of half-life time (t_1/2 = 20 min) and increase in pseudo-order (0.8) is measured at 2.0 mg L^-1. Similar results are obtained with homogenous catalysis by 2.0 mg L^-1 H₂O₂. The combination of H₂O₂ and TiO₂ catalysts shows additional reduction in half-time life with increase in the pseudo-order to 1.2. The conclusions are (1) heterogenous and homogenous photocatalysis can effectively degrade ofloxacin, (2) combined photocatalysis yields higher pseudo-order, being less prone to achieve full removal, (3) analysis of specific pseudo-orders in AOPs of refractory pollutants helps to further elucidate the efficiency of the processes.

Despite the recent availability of immune checkpoint inhibitors, not all patients affected by Non-Small Cell Lung Cancer (NSCLC) benefit from immunotherapy. The reason for this variability relies to a variety of factors which may allow the identification of novel biomarkers. Presently, a variety of biomarkers are under investigation, including the PD1/PDL1 axis, the tumor mutational burden, and the Microbiota. This latter is made by all bacteria and other microorganisms hosted in our body. The gut microbiota is the most represented and has been involved in different physiological and pathological events, including cancer. In this light, it appears that all conditions modifying gut microbiota can influence cancer, its treatment, and its treatment-related toxicities. The aim of this review is to analyze all conditions influencing the gut microbiota and, therefore, affecting response to immunotherapy, iRAEs and their management in NSCLC patients. The investigation of the landscape of these biological events can allow novel insights for optimal management of NSCLC immunotherapy.

The complexity of software is increasing day by day due to the increase in the size of the projects being developed. For better planning and management of large software projects, estimation of software quality is important. During the development processes, complexity metrics are used for the indication of the attributes/characteristics of the quality software. There are many studies about the effect of the complexity of the software on the cost and quality. In this study, we discussed the effects of software complexity on the quality attributes of the software for open source and closed source software. Though, the quality metrics for open and closed source software are not distinct from each other. In this paper, we comparatively analyzed the impact of complexity metrics on open source and private software. We also presented various models for the management of the project complexity such as William’s Model, Stacey’s Agreement and Certainty matrix, Kahane’s Approach and UCP Model. Quality metrics here refer to the standards for the measurement of the quality of software which contains certain attributes or characteristics of the software that are related to the quality of the software. Certain quality attributes addressed in this study are Usability, Reliability, Security, Portability, Maintainability, Efficiency, Cost, Standards and Availability, etc. Both Open source and Closed source software are evaluated on the basis of these quality attributes. This study also recommended future approaches to manage the quality of project Open source and Closed source software and specify which one of them is mostly used in the industry.

Hypophthalmichthys nobilis are widely distributed in the Yangtze River basin and its related lakes. They are an important economic fish species and are a famous cultured species known as the "Four Famous Domestic Fishes" in China. Currently, with the fishing ban in the Yangtze River basin, fishing for H. nobilis in natural water bodies of the Yangtze River basin has been completely prohibited. In order to identify the sources of H. nobilis appearing in the market, further control and accountability, it is necessary to trace the sources of H. nobilis in the Yangtze River basin and its related water bodies. Therefore, this study identified and traced different sources of H. nobilis through muscle element fingerprint analysis (EFA). The results show that H. nobilis from different stations have characteristic element compositions. The characteristic element of H. nobilis from Wuhan (WH) is Pb, which is significantly higher than that in other stations; the characteristic element from Anqing (AQ) is Hg, which is significantly higher than that in other stations; and the characteristic element from Taihu (TH) is Al, which is significantly higher than that in other water areas. Multivariate analysis selected different spatial distribution patterns of 4 discriminant elements ratios (Pb/Ca, Cr/Ca, Na/Ca, Al/Ca) in the muscle of H. nobilis in the Yangtze River basin and its related lakes. The study suggests that the screened discriminative elements can be used to visually distinguish different sources of H. nobilis, and to quickly trace and verify the origin of newly emerging samples. Therefore, the use of selected discriminant element fingerprint features to trace the origin of new samples has been proven to be feasible. By further discriminating and verifying the muscle element fingerprints of new samples, the discrimination rate is high. Therefore, Multivariate analysis for muscle element fingerprint can be used for origin traceability of samples of unknown origin in market supervision.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

We obtain some generalised Minkowski-type integral formulas for compact Riemannian (resp. spacelike) hypersurfaces in Riemannian (resp. Lorentzian) manifolds admitting an arbitrary vector field that we assume to be timelike in the case where the ambient space is Lorentzian. Some of these formulas generalize existing formulas in the case of conformal and Killing vector fields. We apply these integral formulas to obtain interesting results concerning the characterization of such hypersurfaces in some particular cases such as when the ambient space is Einstein admitting an arbitrary (in particular, conformal or Killing) vector field, and when the hypersurface has constant mean curvature.

This works is related to the modeling of cellulose pyrolysis with a pseudo equilibrium approach. The objective is to model the kinetics of the cellulose pyrolysis with a semi-global mechanism obtained from the literature, in order to obtain the yield and the rate of formation of char. The pseudo equilibrium sense consists in the supposition that the solid phase devolatilization can be described kinetically - at finite rate - , preserving the competitive characteristic between the production of char and tar, while the gas phase can be described by means of chemical equilibrium. A set of ordinary, linear and non linear, differential equations was obtained and solved numerically with a simple but consistent scheme using the Totally Implicit Euler method. Chemical equilibrium was solved using CANTERA coupled with a code written in Matlab. Results showed that the scheme preserve the tar-gas competitive characteristic for cellulose pyrolysis. The gas phase, is defined as a mixture of CO₂, CO, H₂O, CH₄, H₂ and N₂ showed similarly composition compared with models from literature. Finally, the extension of the model to biomass in general, is straightforward, in order to include the hemicellulose and lignin.

Non-standard diesel blends can be harmful to the environment and human health. In this context, a simple analytical method to estimate the biodiesel mixture ratio in diesel was developed based on the impedance spectroscopy (IS) associated with the interdigitated sensors. In this article, four different interdigitated sensors, variable comb spacing (G), were simulated using the COMSOL Multiphysics software. Based on finite element simulations, four interdigitated electrode architectures by manufactured and evaluated. According to the X-ray powder diffraction technique, the deposition of the conductive layer (Au°) over the surface of the dielectric substrate (SiO2) did not alter its phase composition. In the analysis of AFM and SEM, it was possible to observe irregular edges on the electrodes, possibly related to thin layers' manufacturing process and mechanical stability. Another characteristic observed in the AFM images was the height of the step of the gold layer of the sensor. Several cross-sections were obtained, and the mean step value is 225.71 ± 0.0032 nm. Although there are differences in the roughness, the whole sensor has nanometric roughness. Based on the finite element method simulation performed, it can be assumed that the geometric parameters more suitable for the manufacturing of the electrode are: W = 20 µm, L = 1000 µm, G = 50 µm e N = 40 digits. The electrical characterization performed by impedance spectroscopy showed that we could differentiate between biodiesel and diesel fuels and their pseudo-binary mixtures in the low-frequency region.

Deep learning models are part of the family of artificial neural networks and, as such, it suffers of catastrophic interference when they learn sequentially. In addition, most of these models have a rigid architecture which prevents the incremental learning of new classes. To overcome these drawbacks, in this article we propose the Self-Improving Generative Artificial Neural Network (SIGANN), a type of end-to-end Deep Neural Network system which is able to ease the catastrophic forgetting problem when leaning new classes. In this method, we introduce a novelty detection model to automatically detect samples of new classes, moreover an adversarial auto-encoder is used to produce samples of previous classes. This system consists of three main modules: a classifier module implemented using a Deep Convolutional Neural Network, a generator module based on an adversarial autoencoder; and a novelty detection module, implemented using an OpenMax activation function. Using the EMNIST data set, the model was trained incrementally, starting with a small set of classes. The results of the simulation show that SIGANN is able to retain previous knowledge with a gradual forgetfulness for each learning sequence. Moreover, SIGANN can detect new classes that are hidden in the data and, therefore, proceed with incremental class learning.

In the framework of a multiplicative metric space. We have discuss some Properties of convex structures in pseudo multiplicative metric space and have applied these properties toiobtain alfixed point results in complete pseudo. It would be interesting to prove some further results in such metric spaces with completeness property.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Metal complexes feature a wide range of available geometries, diversified lability, controllable hydrolytic stability, and easily available rich redox activity. These characteristics combined with the specific properties of the coordinated organic molecules result in many different mechanisms of biological action, making each of the myriads of the classes of metal coordination compounds unique. This focused review presents combined and systematized results of the studies of a group of copper(I) (pseudo)halide complexes with aromatic diimines and tris(aminomethyl)phosphines of a general formula [CuX(NN)PR₃], where X = I^- or NCS^-, NN = 2,2’-bipyridyl, 1,10-phenanthroline, 2,9-dimethyl-1,10-phenanthroline or 2,2’-biquinoline, and PR₃ = Air-stable tris(aminomethyl)phosphines. The structural and electronic properties of the phosphine ligands and luminescent complexes are discussed. The complexes with 2,9-dimethyl-1,10-phenanthroline, apart from being air- and water-stable, exhibit a very high in vitro antimicriobial activity against the Staphylococcus aureus and Candida albicans. Moreover, some of the complexes also show a strong in vitro antitumor activity against human ovarian carcinoma cell lines: MDAH 2774 and SCOV 3, CT26 (mouse colon carcinoma), and A549 (human lung adenocarcinoma) cell lines. The tested complexes are moderately able to induce DNA lesions through free radical processes, however the trends do not reflect observed differences in biological activity.

Urban floods are typical urban disasters that threaten the economy and development of cities. Sponge cities can improve the flood resistance ability and reduce the floods by setting low-impact development measures (LID). Evaluating the floods reduction benefits is the basic link in the construction of sponge cities. Therefore, it is of great significance to evaluate the benefits of sponge cities from the perspective of different rain patterns. In this study, we investigated the urban runoff of various rainfall patterns in Mianyang city using the Strom Water Management Model (SWMM). We employed 2–100-year return periods and three different temporal rainfall downscaling methods to evaluate rain patterns and simulate urban runoff in Mianyang, with and without the implementation of sponge city measures. After calibration, model performance was validated using multi-source data concerning flood peaks and inter-annual variations in flood magnitude. Notably, the effects of peak rainfall patterns on historical floods were generally greater than the effects of synthetic rainfalls generated by temporal downscaling. Compared to the rainfall patterns of historical flood events, the flood protection capacities of sponge cities tended to be overestimated when using the synthetic rainfall patterns generated by temporal downscaling. Overall, an earlier flood peak was associated with better flood sponge city protection capacity.

Soil potentially toxic elements (PTEs) pollution in black soil is of significant concern in China. However, research is scarce regarding the current status, ecological risk, and human health risk of PTEs in the black soil area of northeast China. In our study, 304 soil samples (0-20 cm) were collected in Gonghe Town, Hailun City. The pollution degree and spatial distribution patterns of soil PTEs were analyzed by using the single-factor pollution index (PI) and the Nemerow pollution index (NPI). The source apportionment of PTEs was carried out by combining correlation analysis, principal component analysis (PCA), and positive matrix factorization (PMF) methods. Meanwhile, the potential ecological risk (RI) and the human health risk (HI) associated with soil contamination from various sources were evaluated through the RI and the HI. The results demonstrated that the average content (mean ± standard deviation) of As, Cd, Cr, Cu, Hg, Ni, Pb, and Zn were 11.16 ± 1.32 mg/kg, 0.11 ± 0.04 mg/kg, 65.29 ± 3.46 mg/kg, 22.56 ± 1.32 mg/kg, 0.03 ± 0.01 mg/kg, 27.07 ± 1.46 mg/kg, 26.09 ± 2.84 mg/kg, and 66.01 ± 4.52 mg/kg, respectively. The overall PTEs in the study area exhibited slight pollution levels. The PCA and PMF model source apportionment was validated against each other to yield four sources, which were natural source (33.2%), irrigation source (29.5%), traffic source (23.4%), and fertilizer source (13.2%). The overall RI in the study area was determined to be at the level of slight ecological risk. The non-carcinogenic risk of PTEs to children and adults was ignored, and the carcinogenic risk was at an acceptable level. The comprehensive analysis of PTEs, pollutant sources, RI, and HI concluded that the fertilizer source should be the primary control source, with Cd identified as the first control PTE. The irrigation source and the traffic source were identified as the secondary control sources, with As, Pb, and Hg identified as the secondary control PTEs. This study revealed the status, risks, and sources of PTEs in black soils and provided a scientific basis of PTEs control for policymakers.

The Digital electronics collaborative enhanced learning (DECEL) project has recently developed an international collaborative education course. Its main objective is to enhance the digital electronics skills of international students by working on a complex, multidisciplinary applied problem using a mixed digital architecture. We have developed a logic level synthesis and dedicated software layers on the Red Pitaya FPGA platform. The diversity of digital concepts to be implemented, from hardware description language (HDL) to high-level languages such as Python or Matlab, forced the students to work together and rapidly improve their skills. Their motivation was fueled by the curiosity of controlling an ultrasound probe to obtain ultrasound signatures. This particular physics, little known to the students, was an additional source of curiosity. The goal of forming an image in a liquid medium was an additional motivating factor for them. The students reported that they learned a lot from the experiment. Thus, the technical parts and pedagogical results are documented in this work for reproducibility.

The escalation of mining activities in the karst regions of Guizhou Province has heightened the occurrence of water-inrush incidents in deep coal mines. This study focused on water-inrush phenomena within the Xinhua mining area of Jinsha County, Guizhou Province, aiming to investigate the sources of these incidents. The findings indicated that the overlying limestone of the Changxing Formation in the coal seam served as a vulnerable aquifer under certain conditions, leading to water inrushes. The analysis of the spatiotemporal distribution patterns of water-inrush incidents at the working face indicated that previous mining operations damaged the shallow Changxing Formation limestone, resulting in the accumulation of goaf water and the formation of numerous mining-induced fractures. These fractures served as rapid conduits for water inrushes from both atmospheric precipitation and underground sources at the deep working face. The examination of surface water and mine water quality demonstrated that both exhibited similar characteristics, predominantly featuring bicarbonate, sulfate, and sodium compositions. Investigation into the relationship between mine water inflow and atmospheric precipitation established that atmospheric precipitation influenced the mine water supply cycle, with a replenishment period of ~10 months during the operational phase of the Jinyuan Coal Mine and about one month post-closure. The fractures induced by mining activities within the Changxing Formation limestone facilitated water flow, with atmospheric precipitation serving as the primary water source for the mine. This study offered a valuable scientific foundation for addressing water-related damage resulting from atmospheric precipitation in mines susceptible to water inrushes under analogous hydrogeological conditions.

Urban tree classification is pivotal in urban planning and management, facilitating informed decision-making processes. In this study, we introduce a novel data presentation method termed Pseudo Tree Crown, designed to enhance the accuracy and efficiency of urban tree classification. Leveraging the latest advancements in artificial intelligence (AI), we employ a state-of-the-art classification scheme, PyTorch, to maximize the accuracy of tree classification. Our results demonstrate a robust classification accuracy of over 95% from high spatial resolution imagery from Unmanned Aerial Vehicle (UAV), underscoring our proposed approach’s effectiveness. Moreover, the adaptability of our method renders it applicable to various study areas, highlighting its versatility and potential for widespread implementation in urban planning and management initiatives.

The inherent dependency of deep learning models to labeled data is a well-known problem and one of the barriers that slows down the integration of such methods into different fields of applied sciences and engineering, in which experimental and numerical methods can easily generate a colossal amount of unlabeled data. This paper proposes an unsupervised domain adaptation methodology that mimics the peer review process to label new observations in a different domain from the training set. The approach evaluates the validity of a hypothesis using domain knowledge acquired from the training set through a similarity analysis, exploring the projected feature space to examine the class centroid shifts. The methodology is tested on a binary classification problem, where synthetic images of cubes and cylinders in different orientations are generated. The methodology improves the accuracy of the object classifier from 60% to around 90% in the case of a domain shift in physical feature space without human labeling.

Ensuring the integrity of scientific literature is essential for advancing knowledge and research. However, the credibility and trustworthiness of scholarly publications are compromised by manipulated citations. Traditional methods, such as manual inspection and basic statistical analyses, have limitations in detecting intricate patterns and subtle manipulations of citations. In recent years, network-based approaches have emerged as promising techniques for identifying and understanding citation manipulation. This study introduces a novel method to identify potential citation manipulation in academic papers using perturbations of a deep embedding model. The key idea is to reconstruct meaningful connections represented by citations within a network by exploring slightly longer alternative paths. These indirect pathways enable the recovery of original and reliable citations while estimating their trustworthiness. The investigation takes a comprehensive approach to link prediction, leveraging the consistent behavior of prominent connections when exposed to network perturbations. Through numerical experiments, the method demonstrates a high capability to identify reliable citations as the core of the analyzed data and to raise suspicions about unreliable references that may have been manipulated.

Bacteria develop various defense mechanisms against stresses, including the bacteriophage infection. The giant phiKZ phage infection induced the appearance of a pseudo-nucleus inside the bacterial cytoplasm. Here, we used FISH, electron tomography and analytical electron microscopy to study the morphology of this unique nucleus-like shell and to demonstrate the distribution of phiKZ and bacterial DNA in infected P. aeruginosa cells. The maturation of the pseudo-nucleus was traced in short intervals for 40 min after infection. This study was accompanied by the identification of phiKZ and bacterial DNA by real-time RCR. We demonstrated that phage DNA that isolated from the cytoplasm during all infection stages were compacted within the pseudo-nucleus in a specific structure. Bacterial DNA was diminished in the course of infection, but did not completely degrade until at least 40 min after phage application. The content of the total phage DNA, on the other hand, increased. EDX analysis confirmed these results and revealed that, during the infection, Sulfur content in the bacterial cytoplasm increased, which suggests the increase of DNA-binding Met-reach proteins synthesis, which could protect bacterial DNA from stress.

As an active device, air source heat pumps (ASHP) are widely used for heating and cooling in buildings. However, in cold regions, their efficiency decreases, and frost formation becomes a significant issue during winter. This paper proposes a new scheme that couples air source heat pumps with passive heating. By using software simulations and mathematical models, the new scheme is compared to traditional ASHP systems to analyze its heating performance in rural homes during winter in China’s cold regions. According to the simulation and calculation analysis, on the coldest day of winter, the coupling scheme can provide approximately 99.41kWh of heat to the interior, surpassing the 86.67kWh required to maintain an indoor temperature of 20℃. The system’s power consumption is 36.96 kWh, which is 66.88% lower than that of traditional heat pump heating. The study shows that a coupled system of air source heat pumps and passive heating has better heating performance in cold regions. By incorporating phase change materials and heat storage media to address the shortage of solar energy at night, the system can meet the heating needs throughout the entire day.

Based on a measuring system to determine levels of spatial organization in 2D polygons (homogeneous or heterogeneous partition of defined areas) lying on principles of regularity, we propose the entropy term linked to the concept of “information”, from the “information theory field”, in order to obtain an information measurement regarding a quantity of or amount of information in the architecture of complex 2D biological organizations. The term “quantity” does not refer to the amount of data (size), but to the probability of a geometrical basic pattern within a set of possible statistical configurations regarding levels of homogeneity and heterogeneity. It is this notion of information that is important in information theory, and measures of information in units of bits, what we propose to use for measuring quantities of organization in the architecture of complex geometrical systems. Two complex systems are tested, biological and non biological in order to obtain experimental results, which are verified with the evaluation criteria “entropy”. Experimental results show that the lowest levels of information and entropy, in addition with low rates of heterogeneity and high rates of homogeneity are particular features of geometrical organizations in biological systems.

Amorphous Indomethacin has enhanced bioavailability over its’ crystalline forms, yet amorphous forms can still possess a wide variety of structures. Here, Empirical Potential Structure Refinement (EPSR) has been used to provide accurate molecular models on the structure of five different amorphous Indomethacin samples, that are consistent with their high energy x-ray diffraction patterns. It is found that the majority of molecules in amorphous Indomethacin are non-bonded or bonded to one neighboring molecule via a single hydrogen bond, in contrast the doubly bonded dimers found in the crystalline state. The EPSR models further indicate a substantial variation in hydrogen bonding between different amorphous forms, leading to a diversity of chain structures not found in any known crystal structures. The majority of hydrogen bonds are associated with the carboxylic acid group, although a significant number of amide hydrogen bonding interactions are also found in the models. Evidence of some dipole-dipole interactions are also observed in the more structurally ordered models. The results are consistent a distribution of Z-isomer intra-molecular type conformations in the more disordered structures, that dis-tort when stronger inter-molecular hydrogen bonding occurs. The findings are supported by 1H and 2H NMR studies of the hydrogen bond dynamics in amorphous Indomethacin.

The Software-Defined Networking concept plays an important role in network management. The central controller, which is the main element of SDN, allows to provide traffic engineering and security solutions in single and multiple-layer networks based on optical transmission. In this work, we compare selected open-source implementations of SDN controllers. Throughput and latency measurements were analyzed using the CBench program. The simulation of a link failure and a controller failure were conducted using the API provided by the Mininet network simulator. For detecting security vulnerabilities, a dedicated program, called sdnpwn, was used. The work provides an overview of the selected controllers, indicating their strengths and weaknesses. Moreover, some implemention suggestions and recommendations are presented.

Solid waste management is a global issue that affects every individual living in the world directly or indirectly. Failing to manage the waste properly will cause harm on public health, our natural environment, and even our happiness and prosperity. When asked about the reason behind the failure of third time plastic ban in Bhutan, one of the Bhutanese said it’s because of the lack of cooperation from public to support the move of government. Clean Bhutan, a non-governmental organization (NGO) that aims Zero Waste Bhutan by 2030, has collected around 5,900 metric tons of waste from December 2014 to February 2018. This project will create some awareness regarding the management of waste at individual level when people come in contact with the family of the researcher. It also talks abot how waste management and biodiversity conservation can go side by side.

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

Excessive nutrient discharge to tropical island coastlines drives eutrophication and algal blooms with significant implications for reef ecosystem condition and provision of ecosystem services. Management actions to address nutrient pollution in coastal ecosystems include setting water quality standards for discharging surface waters. However, these standards do not account for the effects of groundwater discharge, variability in flow, or dilution, all of which may influence assessment of true nutrient impacts on nearshore reef habitats. We developed a method to estimate dissolved inorganic nitrogen (DIN) loads to coastal zones by integrating commonly available datasets within a geospatial modeling framework for Tutuila, American Samoa. The DIN loading model integrated an open-source water budget model, water sampling results, and publically available streamflow data to predict watershed-scale DIN loading to the island’s entire coastline. When compared to surface water pathways, submarine groundwater discharge (SGD) was determined to be the most important coastal delivery mechanism of terrigenous DIN, which supports findings from other tropical islands. Onsite wastewater disposal systems were also found to be the primary anthropogenic sources DIN to coastal waters. Our island-wide DIN loading model provides a simple and robust metric to define spatially-explicit sources and delivery mechanisms of nutrient pollution to nearshore reef habitats. Understanding the sources and primary transport modes of inorganic nitrogen to nearshore reef ecosystems can have significant implications for place-based management interventions aimed at increasing the adaptive capacity of unique island ecosystems to environmental variation and disturbances.

This paper presents the concept of applying incremental capacity analysis (ICA) on the OCV curve in the SoC space. The OCV curve can be obtained from any sequence of discharge or charge current or power pulse with a necessary rest period to allow the cell to reach a pseudo-OCV after each pulse. With a higher resolution (>100 pulses) in the full SoC window, an OCV vs SoC curve can be obtained with sufficient accuracy to perform an ICA on the obtained OCV curve. ICA as a diagnostic technique has commonly been applied on Li-ion cells with a constant charge and discharge at slow currents. However, a slow controlled constant current charge or discharge is normally not feasible and cannot be easily applied to a battery in an application. Here we revisit pulse-based ICA to supplement the conventional constant-current-based technique. Conventional ICA performed on ageing data with constant current is directly compared to ICA performed on a selection of higher resolution OCV curves. The main advantage of OCV-ICA is that it can be applied to most cells and systems without significant interruption of normal cell operation. OCV-ICA provides valuable insights into ageing mechanisms as well as detailed information on changes in internal resistance.

Recently, there has been considerable research on deepfake detection. However, most existing methods face challenges in adapting to the advancements in new generative models within unknown domains. In addition, the emergence of new generative models capable of producing and editing high-quality images, such as Diffusion, Consistency, and LCM, poses a challenge for traditional deepfake training models. These advancements highlight the need for adapting and evolving existing deepfake detection techniques to effectively counter the threats posed by sophisticated image manipulation technologies. In this paper, our objective is to detect deepfake videos in unknown domains using unlabeled data. Specifically, our proposed approach employs Meta Pseudo Labels (MPL) with Supervised Contrastive Learning, so-called SupCon-MPL, allowing the model to be trained on unlabeled images. MPL involves the simultaneous training of both a Teacher model and a Student model, where the Teacher model generates Pseudo Labels utilized to train the Student model. This method aims to enhance the adaptability and robustness of deepfake detection systems against emerging unknown domains. Supervised Contrastive Learning utilizes labels to compare samples within similar classes more intensively, while encouraging greater distinction from samples in dissimilar classes. This facilitates the learning of features in a diverse set of deepfake images by the model, consequently contributing to the performance of deepfake detection in unknown domains. When utilizing the ResNet50 model as the backbone, SupCon-MPL exhibited an improvement of 1.58% in accuracy compared to traditional MPL in known domain detection. Moreover, in the same generation of unknown domain detection, there was a 1.32% accuracy enhancement, while in the detection of post-generation unknown domains, there was an 8.74% increase in accuracy.

Highly-resolved data on water balance components (like runoff or storage) are crucial to improve water management, e.g., in drought or flood situations. Because regional observations of these components cannot be acquired adequately, applying water balance models is a feasible solution. We developed an innovative approach using the physically-based lumped-parameter water balance model BROOK90 (R version) integrated into a sensor network platform to derive daily water budget components for catchments in the Free State of Saxony. The model is not calibrated but rather uses available information on soil, land use and precipitation only. We applied the hydro response units (HRUs) approach for 6175 small and medium-sized catchments. For the evaluation, model output was cross-evaluated in ten selected head catchments in a low mountain range in Saxony. The mean values of Kling-Gupta efficiency (KGE) for the period 2005-2019 to these catchments are 0.63 and 0.75 for daily and monthly discharge simulations, respectively. The simulated evapotranspiration and soil wetness are in good agreement with the SMAP_L4_GPH product in April 2015-2018. The study can be enhanced by using different data platforms as well as available information on study sites.

Background: Metabolic flux analysis (MFA) is an indispensable tool in metabolic engineering. The simplest variant of MFA relies on an overdetermined stoichiometric model of the cell’s metabolism under the pseudo-steady state assumption, to evaluate the intracellular flux distribution. Despite its long history, the issue of model error in the overdetermined MFA, particularly misspecifications of the stoichiometric matrix, has not received much attention. Method: We evaluated the performance of statistical tests from linear least square regressions, namely Ramsey RESET test, F-test and Lagrange multiplier test, in detecting model misspecifications in the overdetermined MFA, particularly missing reactions. We further proposed an iterative procedure using the F-test to correct such an issue. Result: Using Chinese hamster ovary and random metabolic networks, we demonstrated that: (1) a statistically significant regression does not guarantee high accuracy of the flux estimates, (2) the removal of a reaction with a low flux magnitude can cause disproportionately large biases in the flux estimates, (3) the F-test could efficiently detect missing reactions, and (4) the proposed iterative procedure could robustly resolve the omission of reactions. Conclusion: Our work demonstrated that statistical analysis and tests could be used to systematically assess, detect and resolve model misspecifications in the overdetermined MFA.

This paper deals with the formulation of a Cobot kinematic model by developing both the direct and inverse kinematics and choosing the noa transformation matrix for defining the end-effector position and orientation with respect to the base frame. These algorithms have been validated via software in Matlab environment and by means of suitable experimental tests, which have been carried out by using a UR5e Cobot. Moreover, a specific industrial application regarding the robotized assembling of a multi-cylinder IC engine, has been designed in terms of layout and corresponding automatic cycle that is intended as a sequence of the robot elementary actions. In particular, the proposed robotized cell is composed by the UR5e Cobot along with its controller and a suitable electropneumatic circuit that includes a PLC with its user interface, which are both governed by means of a specific electronic board and a switch control box. The IC engine in scale of 1:5 and specific parts of the end-effector, which takes the role of vacuum gripper and torque limiting screwdriver, have been designed and manufactured by using a 3D printer.

Amidst the escalating demands for efficient Intelligent Transportation Systems (ITS) management, the significance of accurate Origin-Destination (OD) data prediction has emerged as a paramount concern, given its indispensable role in the ITS domain. This paper introduces a groundbreaking integrated model, creatively fusing the unique strengths of Graph Convolutional Network (GCN), Residual Neural Network (ResNet), and Long Short-Term Memory Network (LSTM) into a single architecture, which we name GraphResLSTM, to exploit road segment average speed data for OD prediction. Compared with conventional road segment traffic volume data, average speed data is more readily available, significantly reducing the data accessibility barrier for OD prediction. We underscore the critical role of selection of key road segments and employs a combination of Entropy Weight Method and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) to identify 41 representative road segments from the experimental road network. In the experimental phase, we simulate 86400000 seconds of traffic conditions, generating a total of 1440000 data records. Utilizing these simulated data, we design and conduct comparative experiments between models as well as data types. The results demonstrate that both the GraphResLSTM model and road segment average speed data outperform other models and data types notably in OD prediction tasks.

In the early 2000s, matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) emerged as a performant and relevant tool for identifying micro-organisms. Since then, it has become practically essential for identifying bacteria in microbiological diagnostic laboratories. In the last decade, it was successfully applied for arthropod identification allowing to distinguish vectors from non-vectors of infectious diseases. However, identification failures are not rare, hampering it widely use. Failure is generally attributed either to the absence of respective counter species MS spectra in the database, or to the insufficient quality of query MS spectra (i.e. lower intensity and diversity of MS peaks detected). To avoid matching errors due to non-compliant spectra, the development of a strategy for detecting and excluding outlier MS profiles became compulsory. To this end, we created MSProfileR, an R package leading to a bioinformatics tool through a simple installation, integrating the control quality system of MS spectra and an analysis pipeline including peak detection and MS spectra comparisons. MSProfileR can also add metadata concerning the sample that the spectra are derived from. MSProfileR has been developed in the R environment and offers a user-friendly web interface using the R Shiny framework. It is available on Microsoft Windows as a web browser application by simply navigation using the link of the package on the Github. MSProfileR is therefore accessible to non-computer specialists and is freely available to the scientific community. We evaluated MSProfileR using two datasets including exclusively MS spectra from arthropods. In addition to coherent sample classification, outlier MS spectra were detected in each dataset confirming the value of MSProfileR.

The rapid urbanization in China has significantly contributed to the vast expansion of urban built-up areas. Precisely extracting and monitoring these areas is crucial for understanding and optimizing the developmental process and spatial attributes of smart, compact cities. However, most existing studies tend to focus narrowly on a single city or global scale with a single dimension, often ignoring mesoscale analysis across multiple urban agglomerations. In contrast, our study employs GIS and image processing techniques to integrate multi-source data for the identification of built-up areas. We specifically compare and analyze two representative urban agglomerations in China: the Yangtze River Delta (YRD) in the east and the Chengdu-Chongqing (CC) region in the west. We use different methods to extract built-up areas from socio-economic factors, natural surfaces, and traffic network dimensions. Additionally, we utilize a high-precision built-up area dataset of China as a reference for verification and comparison. Our findings reveal several significant insights: (1) The multi-source data fusion approach effectively enhances the extraction of built-up areas within urban agglomerations, achieving higher accuracy than previously employed methods. (2) Our research methodology performs particularly well in the CC urban agglomeration. The average precision rate in CC is 96.03%, while the average precision rate in YRD is lower at 80.33%. This study provides an objective and accurate assessment of distribution characteristics and internal spatial structure of built-up areas within urban agglomerations. This method offers a new perspective for identifying and monitoring built-up areas in Chinese urban agglomerations.

It is shown that the gravitational mass-energy defect could be the main cause of Big Bang energy and triggering inflation in the newborn Universe.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&amp;O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&amp;O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

Neutron beams are an essential tool to investigate material structure and perform non-destructive analysis, as they give unique access to element composition, thus ideally complementing density analysis allowed by standard X-rays investigation. Laser-driven neutron sources, though compact and cost-effective, currently have lower average flux than conventional neutron sources, due to the limited repetition rate of the lasers used so far. However, advancements in laser technology allow nowadays to address this challenge. Here we report results obtained at the Advanced Laser Light Source (ALLS) characterizing stable production of broadband (0.1-2 MeV) neutrons produced at a high repetition rate (0.5 Hz). The interaction of laser pulses of 22 fs duration and 3.2 J on-target energy with 2-µm-thick tantalum targets produced protons in the Target Normal Sheath Acceleration (TNSA) regime up to 7.3 MeV. These protons were subsequently converted into neutrons by (p,n) reactions in Lithium fluoride (LiF). Activation measurements and bubble detectors were used to characterize neutron emissions, with a neutron fluence of up to ~ 1.4 × 10⁵ neutrons/shot/sr, and energies mainly between a few hundred of keV and 2 MeV. The total neutron yield was ~ 5 × 10⁵ neutrons/shot. This paves the way for numerous applications, e.g. in homeland security, material science or cultural heritage.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

Pseudo-nitzschia spp. blooms are a recurrent problem in many coastal areas globally imposing some significant threats to the health of human, ecosystems and economy. Monitoring programmes have been established, where feasible, to mitigate the impacts caused by Pseudo-nitzschia spp. and other harmful algae blooms. The detection of such blooms from satellite data could really provide timely information on emerging risks but the development of taxa-specific algorithms from available multispectral data is still challenged by coupled optical properties with other taxa and water constituents, availability of ground data and generalisation capabilities of algorithms. Here, we developed a new set of algorithms (PNOI) for the detection and monitoring of Pseudo-nitzschia spp. blooms over the Galician coast (NW Iberian Peninsula) from Sentinel-3 OLCI reflectances using support vector machine (SVM). Our algorithm was trained and tested with reflectance data from 260 OLCI images and 4607 Pseudo-nitzschia spp. match up data points, of which 2171 were of high quality. The performance of no bloom/bloom model in the independent test set was robust, showing values of 0.80, 0.72 and 0.79 for area under the curve (AUC), sensitivity and specificity, respectively. Similar results were obtained by our below detection limit/presence model. We also present different model thresholds based on optimisation of true skill statistic (TSS) and F1-score. PNOI outperforms linear models, while its relationship with in-situ chlorophyll-a concentrations is weak demonstrating poor correlation with the phytoplankton abundance. We showcase the importance of PNOI algorithm and OLCI sensor for monitoring the bloom evolution between the weekly ground sampling and during periods of ground data absence, such as due to Covid-19.

This paper aims to demonstrate how the detection of communities for epidemiological networks can be used to reduce the dimensionality of optimal control problems. A range of planted partition stochastic blockmodels are generated, where the underlying communities in the model vary in detectability. A high-performance computing workflow is then used to simulate and estimate reduced model dynamics for the networks, which in turn is used to find optimal control solutions.

Pulmonary Embolism (PE) is the obstruction of blood arteries in the lungs by a blood clot. The mortality risk for PE is approximately 30%. Detecting pulmonary embolism in the segmental arteries of the lung is more challenging than in the main arteries and is very prone to being missed. A computer-based approach was created in this work to automatically identify pulmonary embolism in the segmental arteries using computed tomography images. The system's infrastructure includes an enhanced Mask R-CNN deep neural network that has been trained with images containing PE. The network accurately identifies the location of the pulmonary embolism on the computed tomography picture and successfully extracts its borders. The investigation was conducted by generating a local dataset. The study's performance was evaluated using pulmonary embolisms identified manually by the expert radiologist. The sensitivity, specificity, accuracy, dice coefficient, and Jaccard index values for 2130 pictures were 96.4%, 93.5%, 96.1%, 0.96, and 0.90, respectively. The improved Mask R-CNN model has demonstrated superior performance when compared to the traditional Mask R-CNN and U-Net models. This high-performance technology is designed to identify pulmonary embolism and will aid professionals in assessing the size of the embolism.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

This article systematically studied the A-optimal designs of a high-order mixture central polynomial model, which is an advancement of the research results for the A-optimal design of the most recent third-order mixture central polynomial model and a more accurate response surface model. This article is based on the simplex center design, obtaining measurement values at various design points, and verifying them through the A-optimal equivalence theorem. We also compare the A-efficiency of designs through examples, which can be applied to the A-optimal precise design of the fourth-order mixture model.

Because data authenticity and validity are becoming more and more of a concern in the digital age file security and integrity must be guaranteed. This paper investigates the application of HMAC-SHA256 which combines the Secure Hash Algorithm 256 (SHA256) with a private key for transmission-side source file authentication and verification. The study creates a prototype application to evaluate the efficacy of HMAC-SHA256 in securing file transfers by examining previous investigations on SHA and HMAC. The findings demonstrate that SHA256 produces unique file signatures which successfully guards against unwanted changes. Through the use of cryptographic hashes and secret keys to create distinct digital signatures that guarantee file authenticity HMAC improves security. The study shows that HMAC-SHA256 protects data integrity and detects tampering effectively. It does however stress how crucial it is to comprehend cryptographic concepts and apply these strategies with caution in order to prevent vulnerabilities. Overall the study finds that when properly implemented and updated HMAC-SHA256 greatly enhances file security in the digital age.

Refractoriness to antiseizure medications is still a major concern in the pharmacotherapy of epilepsy. For this reason, we decided to evaluate the combination of levetiracetam and cannabidiol, administered at a subthreshold dose, to limit the possible adverse effects of this phytocannabinoid. We administered levetiracetam (300 mg/kg/day, via osmotic minipumps), cannabidiol (120 mg/kg/day, injected once a day subcutaneously), or their combination for one week in epileptic rats. Saline-treated epileptic rats were the control group. Animals were monitored with video electroencephalography the week before and after the treatment. No changes were found in the controls. Levetiracetam did not significantly reduce the total seizure number or the overall seizure duration. Still, the overall number of seizures (p&lt;0.001, Duncan’s new multiple range test) and their total duration (p&lt;0.01) increased in the week following treatment withdrawal. Cannabidiol did not change seizures when administered as a single drug. Instead, levetiracetam combined with cannabidiol resulted in a significant reduction in the overall number and duration of seizures (p&lt;0.05), when comparing values measured during treatment with both pre- and post-treatment values. These findings depended on changes in convulsive seizures, while non-convulsive seizures were stable. These results suggest cannabidiol determined a remarkable potentiation of levetiracetam antiseizure effects at a subthreshold dose.

Public safety and intelligent surveillance systems critically depend on anomaly behavior detection for effective monitoring. In real-world pedestrian detection scenarios, prevalent challenges such as missed detections, complex background interference, and small target sizes hinder accurate anomaly identification. To address these issues, this study introduces YOLO-ABD, a lightweight method for anomaly behavior detection that integrates small target detection and channel shuffling. This method employs YOLOv8n as the baseline model, incorporating a small target detection mechanism in the Head part and utilizing GSConv convolution in the Backbone to enhance perceptual capability. Additionally, the SimAM attention mechanism is integrated to mitigate complex background interference, thereby improving target detection performance. Evaluation on the IITB-Corridor dataset demonstrated mAP50 and mAP50-95 scores of 89.3% and 60.6%, respectively. Generalization testing on the street-view-gdogo dataset further highlighted the superiority of YOLO-ABD over advanced detection algorithms, underscoring its effectiveness and generalizability. With a relatively small parameter count, YOLO-ABD presents an excellent lightweight solution for pedestrian anomaly behavior detection.

The advantage of FPGAs lies in the ability to implement a fully hardware solution for interfacing with various input/output (I/O) devices. Each block can work in parallel with all the others, simplifying the satisfaction of timing constraints. However, this hardware utilization consumes FPGA resources that could otherwise be allocated to the primary project. An alternative involves employing a small "soft-core" processor implementing I/O in software. With the goal to design and evaluate a new tiny soft-core processor optimized for FPGA resources in I/O , a novel processor named Baby8 is developed. It is an 8-bit CISC soft-core processor optimized for reduced FPGA resources including program size for 8-bit applications. The number of instructions is not large but any instruction can access arbitrary memory locations. The performance and resource utilization of the newly designed processor are evaluated and compared with a variety of other soft-core processors. The results demonstrate its competitive performance, achieving an average maximum clock frequency of approximately 57 MHz and a power consumption of around 2mW. Furthermore, it conserves nearly half of the FPGA resources in implementation.

This study aimed to identify the most beneficial attitudes adopted by enterprise participants during their engagement in open-source software (OSS) activities. For this purpose, we selected repositories from GitHub, featuring the top 10 with the highest stars and forks, classified the participants according to their sentiment states, and compared their productivity. The results indicated that participants with positive sentiments were more productive than those with negative sentiments. Consequently, it can be inferred that encouraging organizations to express positive sentiments towards their developers publicly may stimulate OSS community activities and enhance productivity, thereby potentially leading to increased open innovation and sustainability.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.