Background/Objectives: PEMF therapy has gained significant attention due to its potential benefits in promoting tissue repair and improving overall well-being. Recent publications in the field of exercise physiology, showed that pulsed electromagnetic fields (PEMFs) enhanced the velocity and the quantity of muscle O2 available and the rate of muscle oxygen extraction and utilization, in semi-professional cyclists, during a heavy constant-load exercise. In this paper, we investigate the effect of stimulation on muscular activation, in sedentary young people, during a constant-load exercise, performed at moderate intensity. Methods: Nine male sedentary young people, partic-ipated in this study. The response of the muscle activity, was recorded by surface EMG and assessed measuring the root mean square (RMS) normalized to the peak of the maximum voluntary con-traction. Data were collected in the right vastus Medialis (RVM) and right Biceps Femoris (RBF) at the baseline (standstill sitting), on warm-up (unloaded cycling) and during 30 minutes of con-stant-load exercise, in two experimental conditions (PEMF ON vs PEMF OFF). Results: The mul-tivariate analysis of variance performed on RVM showed a significant effect of PEMF in both warmup and exercise, while on RBF showed a significant effect of PEMF and warmup. Conclusions: PEMF strongly enhanced the amplitude of muscle activity in young sedentary people. The increase in the amplitude of the muscular response may lead to a higher oxygen consumption and release.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

The currently available anti-cancer therapies, such as gamma-radiation and chemotherapeutic agents, induce cell death and cellular senescence not only in cancer cells but also in the adjacent normal tissue. New anti-tumor approaches focus on limiting the side effects on normal cells. In this frame, the potential anti-tumor properties of Pulsed Electromagnetic Fields (PEMFs) through irradiation of breast cancer epithelial cells (MCF-7 and MDA-MB-231) and normal fibroblasts (FF95) were investigated. PEMFs had a frequency of 8 Hz, full-square wave type, magnetic flux density of 0.011 T and applied twice daily for 5 days. Data collected showcases that PEMF application decreases the proliferation rate and viability of breast cancer cells while having the opposite effect on normal fibroblasts. Moreover, PEMF irradiation induced cell death and cellular senescence only in breast cancer cells without any effect in the non-cancerous cells. These findings suggest PEMF irradiation as a novel, non-invasive anti-cancer strategy in combination with senolytic drugs, to eliminate both cancer and the remaining senescent cells while simultaneously avoiding the side effects of the current treatments.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

Background: biophysical stimulation therapy, and in particular Pulsed Electromagnetic Fields (PEMFs) and capacitively coupled electric fields (CCEFs) has significantly increased in the last twenty years. For this, it is necessary to have clear information regarding the efficacy, the therapeutic indication and the expected objectives. Methods: we conducted a narrative review taking into consideration different types of studies with different areas of application. The objective was to take into consideration and analyze the different fields of use and the relevant information present in the literature. Results: There is unanimous opinion regarding the usefulness of applying biophysical therapy on the bone compartment both in terms of the tissue healing process and the symptoms associated with this situation. Differently, but no less importantly, in the joint compartment positive opinions were observed mainly on the inflammatory and catabolic process, however, at present,we did not report evidence regarding cartilaginous tissue regeneration. Conclusion: the effectiveness of PEMFs and CCEFs on the bone healing process in the Orthopedic and Traumatology fields is consolidated evidence in the literature. We have also found positive results on symptoms and patient compliance with rehabilitation therapies. Therefore, notable application can be envisaged in the fields of Prosthetic Surgery and Sports Medicine.

The paper is dedicated to the topical problem of examining permafrost state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we propose and scientifically substantiate a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings and constructions.

Effects of pulsed electromagnetic fields (PEMF) on immunological factors in a 2,4-dinitrochlorobenzene (DNCB)-induced atopic dermatitis (AD) model were investigated. Hairless mice were randomly assigned to control, acetone and olive oil solution-treated (AOO), PEMF 15 Hz, PEMF 75 Hz, and sham groups (n=5 each). AOO solution was used to dissolve DNCB. Both PEMF and sham groups were exposed to similar DNCB doses, causing similar AD symptoms. After AD induction for five weeks, only the PEMF group was exposed to PEMF stimulations (15 Hz, 75 Hz, and 15 mT) for two weeks inside the solenoid coil. In both groups, splenomegaly was observed, as AD was induced by hyperimmune reactions caused by DNCB sensitization. However, splenomegaly did not occur in the PEMF-exposed groups, and spleen weight decreased similarly to that of the control. Hence, the total splenocytes in the PEMF group were similar to those in the control group, whereas the sham group showed thrice the number of splenocytes compared to the PEMF group. The serum immunoglobulin E levels did not significantly change in the PEMF group; however, they increased more than fourfold in the sham group. These results demonstrate that PEMF stimulation ameliorates the abnormal symptoms caused by hyperimmune reactions.

The scope of this work was part of our previous research on Pulsed Power Plasma Stimulation Technique. Electromagnetic fields generated during a pulsed power plasma discharge were simulated using a finite element method in the COMSOL RF module. The field distributions were calculated during and after the pulse. The current paper takes advantage of prior work measuring and modeling the current distribution in the plasma arc. Agreement with laboratory experimental measurements provides support for extension of the model to reservoir scale. The validated model was used to quantify the signal attenuation level in different medium environment.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

Determining the vibration environment is crucial to analyzing a design of any mechanical system, especially such dynamic systems as sounding rockets. Accuracy of measurement using accelerometers could be improved by application of mechanical vibration filtering and amplifying devices. This work presents a theoretical description of a tunable filter and amplifier. Principle of work is provided as well as results from application of the device on a sounding rocket are provided. It is shown that implementation of such devices allowed for enhancing the accuracy of acceleration measurements. Conclusions on future implementations are also provided.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Based on the theory of turbulence, equations are derived for estimations of turbulent fluctuations of the longitudinal and transverse components of the wind velocity during ideal hovering of a quadcopter in a turbulent atmosphere. We present the results of experiments which were carried out on the territory of the Geophysical Observatory of Institute of Monitoring of Climatic and Ecological Systems, Siberian Branch, Russian Academy of Sciences, located in Tomsk Akademgorodok on the territory with complex orography, in a parkland zone with buildings of research institutes and motorways. Time series of turbulent fluctuations of the longitudinal and transverse components of wind velocity fluctuations were received with the use of an automated weather station, and time series of estimates of these components, from data of a DJI Phantom 4 Pro quadcopter during hovering. According to the automated weather station data, anisotropy was observed in one experiment during measurements in the atmosphere, but this phenomenon was not observed in the other experiment: the fluctuation spectra of all components of wind speed fluctuations coincide. The spectra of fluctuations of the longitudinal and transverse wind velocity components based on the automated weather station data and UAV telemetry are presented. The fluctuation spectra of these components for the automated weather station data and quadcopter generally coincide. The behavior of the spectra coincides with the spectrum which corresponds to Kolmogorov–Obukhov “–5/3” law within the inertial range. The turbulent spectra of the wind velocity fluctuations obtained with the use of the automatic weather station and with the unmanned aerial vehicle differ in the high-frequency spectral region.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Background: Tibial shaft fractures are the most common of long bone fractures. The gold standard for management is locked intramedullary nailing. The freehand method under fluoroscopic monitoring is the most often utilized method for distal screw locking. Electromagnetic guidance-based distal screw locking methods have gained popularity recently. The study's objective is to evaluate the system using electromagnetic tracking data against the free-hand technique. Methods: Sixty-three patients who received intramedullary nailing for tibial shaft fractures at our institute between January 2018 and May 2022, were included in this study. Two groups of patients were distinguished: Group FH underwent freehand distal locking and intramedullary nailing, while Group SS underwent electromagnetically guided locking. Radiation exposure period, as well as dose area product, were noted and statistically compared. Results: In terms of dose area product, a mean value of 43.57±31.57 cGy/cm2 in group FH and a mean value of 27.62±11.20 cGy/cm2 in group SS (p < 0.05) was assessed. Concerning the duration of surgery a mean value of 128.83±26.51 minutes was reported in group FH and a mean value of 126.42±48.31 minutes in group SS (p > 0.05). Conclusions: This study confirms the use of electromagnetic-guided locking distal screws reduces the total time of exposure to ionizing radiation, with no difference in operating time.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

This paper presents a novel sensor for the detection and characterization of regions of air turbulence that would be of use to improve UAV stability in bad weather. It consists of a combined Schlieren imager and a Radar Acoustic Sounding System (RASS) to produce dual modality “images” of air movement within the measurement volume. The ultrasound modulated Schlieren imager consists of a strobed point light source, parabolic mirror, light-block and camera which are controlled by two laptops. It provides a fine scale projection of the acoustic pulse modulated air turbulence through the measurement volume. The narrow beam 40 kHz/ 17 GHz RASS produces spectra based on Bragg enhanced Doppler radar reflections from the acoustic pulse as it travels. Tests using artificially generated air vortices showed some disruption of the Schlieren image and of the RASS spectrogram. This should allow the higher resolution Schlieren images to identify the turbulence mechanisms that are disrupting the RASS spectra.

Deep underground laboratories offer advantages for conducting high-precision observations of weak geophysical signals, benefitting from a low background noise level. It is both valuable and feasible to enhance strong, noisy ground electromagnetic (EM) field data using synchronously recorded underground EM signals, which typically exhibit a high signal-to-noise ratio. In this study, we propose an EM field reconstruction method employing a Long Short-Term Memory (LSTM) recurrent neural network with referenced deep underground EM observations. Initially, a deep learning model was developed to capture the time-varying features of underground multi-component EM fields using the LSTM recurrent neural network. Subsequently, this model was applied to process synchronously observed strong, noisy data from other conventional observation systems, such as those at surface, to achieve noise suppression through signal reconstructions. Both theoretical analysis and practical observational data suggest that the proposed method effectively suppresses noise and reconstructs clean EM signals. This method is efficient and time-saving, representing an effective approach to fully utilizing the advantages of deep underground observation data. Furthermore, this method could be extended to the processing and analysis of other geophysical data.

For the first time, the effect of a significant change in the resistance of the aquatic environment of a population of protozoan microorganisms under the influence of radiofrequency electromagnetic radiation from cell phones has been experimentally studied. The results of the experiment demonstrate the biological nature of the changes occurring in the “water population of protozoa” system, which indicates that the impact of radiation directly affects the cell. This conclusion is confirmed by the same order of magnitude time of information exchange between individual individuals of the population in the calculation and in the experiment. An extremely low concentration of protozoa in the experiment was established, equal to 1000 pcs./liter, at which the indicated effect is observed.An unambiguous dependence of the biological effect in the “water – amoeba population” system on the average power of electromagnetic radiation of cell phones, both in standby mode and in talk mode, has been established. It is concluded that the presented method of changing the physical properties of the aquatic environment of a population of protozoa under the influence of electromagnetic fields can be a model experiment in identifying the mechanisms of interaction of biological systems with electromagnetic radiation, determining the response time of biological systems to external electromagnetic influence, and establishing the degree of influence of radiation in the 4G, 5G ranges.

Low-frequency electromagnetic induction (EMI) is a non-invasive geophysical method that is based on the induction of electromagnetic (EM) waves into the subsurface to quantify changes in electrical conductivity. In this study we present an open (design details and software are accessible) and modular system for the collection of EMI data. The instrument proposed allows to adjust the separations between the transmitter and up to four receiving antennas as well as the acquisition frequency (in the range between 3 and 50 kHz) to permit measurements with variable depth of investigation. The sensor provides access to raw data and the software described in this study allows control of the signal processing chain. The design specifications permit apparent conductivity measurements in the range of between 1 mS/m and 1000 mS/m, with a resolution of 1.0 mS/m and with a sampling rate of up to 10 samples per second. The sensor allows for a synchronous acquisition of a time stamp and a location stamp for each data sample. The sensor has a mass of less than 5 kg, is portable and suitable for 1-person operation, provides 4 hours of operation time on one battery charge, and provides sufficient rigidity for practical field operations.

Earthquake forecasting is arguably one of the most challenging tasks in Earth sciences owing to the high complexity of the earthquake process. Over the past 40 years, there has been a plethora of work on finding credible, consistent and accurate earthquake precursors. This paper is a cumulative survey on earthquake precursor research, arranged into two broad categories: electromagnetic precursors and radon precursors. In the first category, methods related to measuring electromagnetic radiation in a wide frequency range, i.e. from a few hz to several MHz, are presented. Precursors based on optical and radar imaging acquired by space borne sensors are also considered, in the broad sense, as electromagnetic. In the second category, concentration measurements of radon gas found in soil and air, or even in ground water after being dissolved, form the basis of radon activity precursors. Well-established mathematical techniques for analysing data derived from electromagnetic radiation and radon concentration measurements are also described with an emphasis on fractal methods. Finally, physical models of earthquake generation and propagation aiming at interpreting the foundation of the aforementioned seismic precursors, are investigated

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

The well-being and sociability of individuals have always been part of modernity. The development of new technologies that meet these aspirations is receiving increasing attention. Thus, strengthening the desired objectives of these tools and minimizing their undesirable side effects is the subject of a growing commitment. The present contribution aims, in this context, to evaluate and analyze the desired and undesirable effects of the interaction of electromagnetic fields with living tissues in general. This involves routines reinforcing expected functions as well as those controlling and protecting against undesirable effects. First, the interactions of electromagnetic fields with tissues are analyzed, involving their thermal biological effects of desired and undesired exposures. The roles of blood and sap fluids in bio-affected tissues are then analyzed. Secondly, the governing electromagnetic, bio-heat equations, and their coupled solution are studied. Third, the thermal behavior of tissues and the exposure adverse effects are examined. Next, monitoring and defending of the effects of exposures are discussed. This contribution illustrates and discusses mathematical modeling routines based on a generalized interaction of electromagnetic fields with living tissues.

Conversion of electromagnetic energy into magnetohydrodynamic energy occurs when the electric conductivity changes from negligible to finite values. This process is relevant during the epoch of reheating of the early Universe at the end of inflation and before the emergence of the radiation-dominated era. We find that conversion into kinetic and thermal energies is primarily the result of electric energy dissipation and that the magnetic energy plays only a secondary role in this process. This means that, since electric energy dominates over magnetic energy during inflation and reheating, significant amounts of electric energy can be converted into magnetohydrodynamic energy when conductivity emerges early enough, before the relevant length scales become stable.

An eigenvalue equation representing symmetric (dual) quantum equation is introduced. The particle is described by two scalar wavefunctions, and two vector wavefunctions. The eigenfunction is found to satisfy the quantum Telegraph equation keeping the form of the particle fixed but decaying its amplitude. An analogy with Maxwellian equations is presented. Massive electromagnetic field will satisfy a quantum Telegraph equation instead of a pure wave equation. This equation resembles the motion of the electromagnetic field in a conducting medium. With a particular setting of the scalar and vector wavefunctions, the dual quantum equations are found to yield the quantized Maxwell's equations. The total energy of the particle is related to the phase velocity ($v_p$) of the wave representing it by $E=p\,|v_p|$, where $p$ is the matter wave momentum. A particular solution which describes the process under which the particle undergoes a creation and annihilation is derived. The force acting on the moving particle is expressed in a dual Lorentz-like form. If the particle moves like a fluid, a dissipative (drag) quantum force will arise.

Pulsed thermography is a vital technique in the nondestructive evaluation field. However, its data analysis can be complex and requires skilled experts. Advances in deep learning have yielded exceptional results, including image segmentation. Therefore, many efforts have been made to apply deep learning methods to data processing for nondestructive evaluation. Despite this, there is currently no public Pulsed thermographic dataset available for evaluating various spatial-temporal deep methods of segmenting pulsed thermographic data. This article aims to provide such a dataset and assess the performance of commonly used deep learning-based instance segmentation models on it. Additionally, the impact of the number of frames and data transformations on model performance is examined. The findings suggest that suitable preprocessing methods can effectively reduce the data size without compromising the deep models’ performance.

Liquid propellants are fast becoming attractive for pulsed plasma thrusters due to their high efficiency and low contamination issues. However, the complete plasma interaction and acceleration processes are still not very clear. Present paper develops a multi-layer numerical model for liquid propellant PPTs. The model proposes a possible acceleration mechanism for liquid fed pulsed plasma thrusters and accurately predicts the propellant utilization capabilities and estimations for the fraction of propellant gas that is completely ionized and accelerated to high exit velocities. Validation of the numerical model and the assumptions on which the model is based on is achieved by comparing the experimental results from two different liquid-fed thrusters developed at the University of Tokyo. Results show 50% of liquid propellant injected is completely ionized and accelerated to high exit velocities (> 50Km/s), whereas, neutral gas contribute to only 7% of the total specific impulse and accelerated to low exit velocity (< 4Km/s). The model shows an accuracy up-to 92%. Optimization methods are briefly discussed to ensure efficient propellant utilization and performance. The model acts as a tool to understand the background physics and to optimize the performance for liquid-fed PPTs.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

The analysis of data produced by the MV20/20 sensor, tagged with quality outcomes, is presented with the aim of developing a predictor model for real-time anomaly detection and classification. Three types of inclusions, undesired particles that deteriorate the quality of production, are used to tag the quality data using results from the lab. We explore both unsupervised and supervised learning, which both offer advantages in monitoring and controlling the quality of production. It is discovered that the dataset can be clustered using techniques like K-Means and DBSCAN. Bounding the data within a 95% confidence interval ellipse ensures we can detect anomalous events in real time. For supervised learning, a two-stage classifier is explored, which classifies the outcome of a cast and secondly the inclusion responsible for the negative outcome. We explore models from logistic regression and support vector machines, to two neural networks, namely the multi-layer perceptron and the radial basis function network. While the cast outcome is adequately predicted by all the models, the multi-layer perceptron provides a boundary performance for the inclusion type. A more advanced technique for model optimisation, namely grid search, is applied in order to improve on the results. The outcome for the grid search is not much better, which indicates a global maximum in the learning capacity of the model. Recommendations include the addition of sensor systems and an audit of data collection variation.

In this article, many experimental similarities between electromagnetic fields (which are applied in systems of electrons, atoms, and liquids) and strong interaction fields (which are applied in systems of quarks, nucleons, and nuclei) are reviewed. The currently accepted theories describing electromagnetic fields differ fundamentally from those describing strong fields. Therefore, the many similarities are quite surprising, and some are not adequately explained even today. Several such unexplained similarities are listed among the top open problems in particle physics, such as the “EMC effect,” the “proton spin crisis,” and the “strong CP problem.” This paper highlights, for the first time, the underlying common characteristics of these problems, potentially offering valuable contribution to future explanations.

The wide application of graphene in the industry requires the direct growth of graphene films on silicon substrates. In this study, we find a possible technique to meet the requirement above. Multilayer graphene thin films (MLG) are grown without a catalyst on Si/SiO2 by pulsed laser deposition (PLD). It was found that the minimum number of laser pulses that are required to produce fully covered (uninterrupted) samples is 500. This number of laser pulses resulted in samples that contain ~5 layers of graphene. The number of layers was not affected by the laser fluence and the sample cooling rate after the deposition. However, the increase of the laser flu-ence from 0.9 J/cm2 to 1.5 J/cm2, results in 2.5 fold reduction of the MLG resistance. The present study reveals that the PLD method is suitable to produce nanocrystalline multilayer graphene with electrical conductivity of the same magnitude as commercial CVD graphene samples.

We consider the propagation of electromagnetic waves in the Friedman – Lemaître – Robertson – Walker metric. The exact solutions for plane and spherical wave are written down. The corresponding redshift, amplitude change, and dispersion are discussed. We also speculate about the connection of the electromagnetic wave equation to the Klein–Gordon equation.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

Diabetic patients need long-term and frequent glucose monitoring to assist in insulin intake. The current finger-prick devices are painful and costly which make noninvasive glucose sensors highly demanded. In this review paper, we discuss several advanced electromagnetic (EM) wave based technologies for noninvasive glucose measurement, including infrared (IR) spectroscopy, photoacoustic (PA) spectroscopy, Raman spectroscopy, fluorescence, optical coherent tomography (OCT) and microwave sensing. Development and progress of each method are discussed regarding fundamental principle, system setup and experimental results. Despite the promising achievements reported previously, there is no established product to obtain FDA approval or survive marketing test. Limitations and prospects of these techniques are discussed at the end of this review.

Rhenium Disulfide (ReS2) has evolved as a novel 2D transition-metal dichalcogenide (TMD) material which has promising applications in optoelectronics and photonics because of its distinctive anisotropic attributes. In this review, we emphasize on formulating saturable absorbers (SAs) based on ReS2 to produce Q-switched and mode-locked pulsed lasers of diverse operation wavelengths like 1 μm, 1.5 μm, 2 μm, and 3 μm. We outline ReS2 synthesis techniques and integration platforms concerning solid-state and fiber-type lasers. We discuss the laser performance based on SAs attributes. Lastly, we draw conclusions and outlook by recommending additional improvements for SA devices so as to advance the domain of ultrafast photonic technology.

A highly-integrated experimental system for plasma decomposition of fuels was built. Experiments were conducted and confirmed that macromolecular chain hydrocarbons were cracked by large-gap dielectric barrier discharge under the excitation of a microsecond-pulse power supply. Alkanes and olefins with a C atom number smaller than 10 as well as hydrogen were found in the cracked products of n-decane (n-C10H22). The combination of preheating and plasma decomposition had strong selectivity for olefins. Under strong discharge conditions, micromolecular olefins were found in the products. Moreover, there was a general tendency that micromolecular olefins gradually accounted for higher percentage of products at higher temperature and discharge frequency.

At present, the applications and efficacy of non-ionizing radiations (NIR) in oncotherapy are limited. In terms of potential combinations, the use of biocompatible magnetic nanoparticles as heat mediators has been extensively investigated. Nevertheless, the development of more efficient heat nanomediators that may exhibit high specific absorption rates still is an unsolved problem. Our aim was to investigate if externally applied magnetic fields and a heat-inducing NIR affect tumor cell viability. To this end, under in vitro conditions, different human cancer cells (A2058 melanoma, AsPC1 pancreas carcinoma, MDA-MB-231 breast carcinoma) were treated with the combination of electromagnetic fields (EMFs, using solenoids) and hyperthermia (HT, using a thermostated bath). The effect of NIR was also studied in combination with standard chemotherapy and targeted therapy. An experimental device combining EMFs and high intensity focused ultrasounds (HIFU)-induced HT was tested in vivo. EMFs (25 T, 4h) or HT (52C, 40 min) showed a limited effect on cancer cell viability in vitro. However, their combination decreased viability to approx. 16%, 50%, and 21% of controls values in A2058, AsPC1, and MDA-MB-231 cells, respectively. Increased lysosomal permeability, release of cathepsins into the cytosol and mitochondria-dependent activation of cell death are the underlying mechanisms. Cancer cells could be completely eliminated combining EMFs, HT and standard chemotherapy or EMFs, HT and anti-Hsp70-targeted therapy. As a proof of concept, in vivo experiments performed in AsPC1 xenografts showed that combination of EMFs, HIFU-induced HT, standard chemotherapy and a lysosomal permeabilizer induces a complete cancer regression.

Considerable efforts have been devoted to modifying gravity, which aim to elucidate the possible existence or nature of dark matter and energy, describe observational data more effectively, and formulate quantum gravity. In addition, despite the immense success of the quantum field theory, the framework requires renormalization techniques and breaks down at high energies. Recently, the Planck legacy 2018 release has confirmed the existence of an enhanced lensing amplitude in the cosmic microwave background power spectra, which prefers a positively curved early Universe with a confidence level higher than 99%. This study considers the implied curvature of the early Universe as the curvature of “the background or 4D conformal bulk as a manifestation of vacuum energy” and distinguishes it from the localized curvature that is induced in the bulk by the presence of celestial objects that are regarded as ”4D relativistic cloud-worlds.” Analogously, because gravity appears to emerge owing to spacetime curvature and does not exhibit critical characteristics shared by other fields, it has been incorporated as the local curvature of the bulk affecting the embedded quantum fields that are regarded as propagating “4D relativistic quantum clouds.” To consider the effects of the bulk on embedded clouds, this paper presents interaction field equations in terms of brane-world modified gravity and the perspective of geometrization of the quantum mechanics wherein gravity is manifested by the curvature of 4D conformal bulk as an indicator of the field strength of vacuum energy on the embedded 4D relativistic clouds in addition to the boundary interactions, which could remove the singularities and satisfy a conformal invariance theory. A visualization of the evolution of the 4D relativistic cloud-worlds over the conformal spacetime of the 4D bulk is presented, whereas the standard said theories can be recovered from the interaction field equations.

We derive the thermal noise spectrum of the Fourier transform of the electric field operator of a given wave vector starting from the quantum-statistical definitions and relate it to the complex frequency and wave vector dependent complex conductivity in a homogeneous, isotropic system of electromagnetic interacting electrons. We analyze separately the longitudinal and transverse case with their peculiarities. The Nyquist formula for vanishing frequency and wave vector, as well as its modification for non-vanishing frequencies and wave vectors follow immediately. Furthermore we discuss also the noise of the photon occupation numbers. It is important to stress that no additional assumptions at all were used in this straightforward proof.

Modern life implies a constant exposure of living organisms to electromagnetic fields generated by human made technology. The question of whether or not electromagnetic fields in the non-ionizing frequency range can affect cellular functions, increasing the risk of cancer or another pathologies is currently a subject of interest for scientific community of several disciplines of physics, biology, chemistry and medicine. The first part of this short review presents briefly the possible mechanism of interaction of electromagnetic fields in cellular level based in theoretical models and experimental results. The second part refers to experimental observations published by several authors about the potential cytotoxic and genotoxic effects of electromagnetic fields. Results of researches are no yet conclusive enough to accept or reject the genotoxic, carcinogenic or cytotoxic potential of these fields. Up to date the International Agency for Research on Cancer (IARC) has classified the X, gamma and ultraviolet radiation as carcinogenic and the fields generated by radio frequencies as possibly carcinogenic.

We employ another approach to quantize electromagnetic fields in the coordinate space, instead of the mode (or Fourier) space, such that local features of photons can be efficiently, physically, and more intuitively described. To do this, coordinate-ladder operators are defined from mode-ladder operators via the unitary transformation of systems involved in arbitrary inhomogeneous dielectric media. Then, one can expand electromagnetic field operators through the coordinate-ladder operators weighted by non-orthogonal and spatially-localized bases, which are propagators of initial quantum electromagnetic (complex-valued) field operators. Here, we call them QEM-CV-propagators. However, there are no general closed form solutions available for them. This inspires us to develop a quantum finite-difference time-domain (Q-FDTD) scheme to numerically time evolve QEM-CV-propagators. In order to check the validity of the proposed Q-FDTD scheme, we perform computer simulations to observe the Hong-Ou-Mandel effect resulting from the destructive interference of two photons in a 50/50 quantum beam splitter.

Electric and/or magnetic fields are generated by stationary charges, uniformly moving charges and accelerating charges. These field components are described in the literature as static fields, velocity fields (or generalized Coulomb field) and radiation fields (or acceleration fields), respectively. In the literature, the electromagnetic fields generated by lightning return strokes are presented using the field components associated with short dipoles and in this description the one to one association of the electromagnetic field terms with the physical process that gives rise to them is lost. In this paper, we will derive expressions for the electromagnetic fields using field equations associated with accelerating (and moving) charges and separate the resulting fields into static, velocity and radiation fields. The results illustrates how the radiation fields emanating from the lightning channel give rise to field terms varying as inverse of distance and distance squired, the velocity fields generating field terms varying as inverse of distance squired and the static fields generating fields components varying as inverse of distance squired and distance cube. These field components depend explicitly on the speed of propagation of the current pulse. However, the total field does not depend explicitly on the speed of propagation of the current pulse. It is shown that these field components can be combined to generate the field components pertinent to the dipole technique. However, in this conversion process the connection of the field components to the physical process taking place at the source that generate these fields (i.e. static charges, uniformly moving charges and accelerating charges) is lost.

A novel technique suitable for propulsion of small unmanned aerial vehicles (UAV) is discussed in this paper. This approach utilizes the rotational energy of airborne gyro rotors and converts it into translational propulsion for the vehicle. The energy conversion is achieved by generating precisely directed centrifugal force pulses through short-duration rotor unbalances. The accurate control of the timing and magnitude of these unbalances is crucial for successful propulsion generation. Our first-order theory of controlled unbalance propulsion (CUP) predicts the potential for achieving high translational accelerations and vehicle velocities up to orbital levels. Power saving levitation of UAVs can be attained. In this paper, we provide traceable evidence that pulsed centrifugal propulsion is based on well-established laws of physics and can be realized using state-of-the-art technologies.

Dry eye disease (DED) most commonly caused by evaporative subtypes and mainly induced by meibomian gland dysfunction (MGD). Intense pulsed light (IPL) combined with meibomian gland expression (MGX) is noninvasive treatment for improvement of ocular discomfort symptoms and MGD. In this prospective study between November 2020 and May 2022, the patients met the criteria of both ocular surface disease index (OSDI) ≥13 scores and standardized patient evaluation of eye dryness (SPEED)≥ 8 scores were enrolled in Kaohsiung Veteran General Hospital. Three separate treatment sessions of IPL therapy combined with MGX administered to the lower lids with an interval of 28 days. Further tear film assessment included lipid layer thickness (LLT), tear meniscus height (TMH), non-invasive tear break-up time (NIBUT), meibomian gland loss (MGL) either beforeor after 1st and 3rd IPL therapy combined with MGX. Besides, lissamine green staining and pain scores were also recorded. We totally enrolled 37 patients of 74 eyes. Men accounted for 18.92% (7/37). The mean age was 54.51 ± 11.72 years. The mean OSDI scores were 58.12 ± 22, while the SPEED scores were 17.03 ± 5.98. The mean Schirmer’s test was 3.66 ± 2.43 mm. After three sessions IPL treatment with MGX, the OSDI, SPEED, LLT, TMH, MGL, MGXS and pain scores were significantly improved. For the MGX scores (MGXS) ≤20 group, MGL and lissamine green scores showed significant improvements. For the MGXS >20 group, TMH and dry spot rate revealed statistically improvement. Noninvasive IPL therapy with MGX statistically improved not only dry eye symptoms but also tear film assessments.

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

We propose a novel framework for understanding quantum phenomena through the lens of a modified electromagnetic spacetime governed by Einstein field equations. By assuming the existence of an electromagnetic spacetime that adheres to these modified geodesic and Einstein field equations, provided the field equations satisfy the Coulomb force law in weak-field approximations, we explore the derivation of Maxwell’s equations and highlight the necessity of incorporating spin to validate these equations. We derive the wave equation for the normalized transverse metric and establish its equivalence with the de Broglie wave proposition, suggesting a relationship between this metric and the particle's wavefunction. This approach offers a classical explanation for several quantum phenomena, including the double-slit experiment, entanglement, tunneling, non-locality, and wavefunction collapse. Additionally, it posits a method to visualize atomic orbital structures in line with quantum mechanical predictions. These findings suggest that the foundational principles of quantum mechanics can be interpreted as linearized approximations of general relativity applied to electromagnetic spacetime. While this theory does not yet extend to the correlations between general relativity, quantum electrodynamics (QED), and quantum chromodynamics (QCD), it provides a valuable visualization tool for physicists and advances our understanding of the unresolved challenges linking quantum mechanics with general relativity.

The development of devices for In-Situ Resource Utilization (ISRU) of the lunar surface powder (regolith) by means of microwaves needs regolith simulants with electromagnetic properties similar to the lunar regolith. This document deals with the measurement of complex permittivity and dielectric loss tangent of the aforementioned simulants at ambient temperature from 400 MHz to 20 GHz. In addition, further studies are carried out taking into account humidity of the samples and their densities. The obtained results will be applicable for comparing the measured values of EAC-1A and JSC-2A among them and with other previously measured simulants and real samples. The measurements are carried out applying two different nonresonant techniques: Open- Ended Coaxial Probe (OECP) and Transmission Line. For this purpose, the DAK and EpsiMu commercial kits were respectively used.

A deep relationship is identified between the Coulomb Force and Gravity. A gravitational constant for strong gravity is calculated from the relationship. The equivalence between mass and charge is explored. Implications are given for the expansion of Einstein's Field Equations to include vector gravity.

We investigate regular damped oscillatory structures appearing in the "effective" form factor of various hadrons. The behavior of this form factor can be extracted from the experimental information on total cross sections, the processes $\sigma_{tot}(e^+e^- \to h \bar h)$, $h=\pi^{\pm}, K^{\pm}, K^0, p, n $ are examined. The apparent oscillations have been observed for the first time for the proton and we show, taking also other hadrons into the consideration, that they are an arbitrary artifact resulting from a very simplistic theoretical description based on an elementary three-parametric model. If the data are described by a more appropriate and well physically funded U\&A model, then the oscillations disappear. In addition, if the simple model is used to describe the data, one observes that the oscillations are opposite for particles which form an isospin dublet. We show, by using the U\&A model, that this feature is explained by the transformation properties of the corresponding states in the isotopic space.

During the explosion of energetic materials, obvious electromagnetic interference will be generated, which will affect the normal operation of surrounding electronic equipment. Experiments are still an important means to study this issue. A set of electromagnetic radiation measurement device based on short-wave omnidirectional antenna and ultra-wideband omnidirectional antenna is designed to measure the electromagnetic radiation generated by the explosion of energetic materials of different masses, and the electromagnetic radiation characteristics are obtained through data processing. The results show that the mass of the energetic material has a significant effect on the time-domain characteristics of the electromagnetic radiation generated by the explosion: the higher the mass of the energetic material, the shorter the delay response of the electromagnetic signal, the longer the duration, and the earlier the peak appears. The frequency of electromagnetic radiation signals generated by the explosion of energetic materials is mainly concentrated below 100 MHz, and the energy is most concentrated in the frequency band of 0~50 MHz. The composition of energetic materials has the greatest influence on the spectral distribution, and the spectral distribution of electromagnetic radiation produced by the explosion of explosives with different compositions has obvious specificity. The electromagnetic radiation intensity generated by the explosion of energetic materials has a strong correlation with the distance from the explosion center, and it decreases with the increase of the distance, and the decreasing range is large. The structure and detonation method of energetic materials can change the geometrical motion mode during the explosion, resulting in the non-uniformity of electromagnetic radiation propagation.

The detection of Dark Matter is the greatest outstanding problem in modern cosmology. Several attempts have been taken for this without any remarkable success. To find out a suitable way of detection we need to understand its nature comprehensively. In the present article, a hypothesis is described considering Dark Matter as a normal matter. Its peculiar behavior is explained considering its existence in BEC state in the coolest part of the universe that makes it an electromagnetic insulator. Depending upon this hypothesis an experimental verification method is proposed.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

MgB2 is a hexagonal superconducting material, and its simple composition has led to the development of low-cost practical wires. However, the problem is that the strain characteristics of filaments are inferior to those of other practical wires, but there have been no strain measurements using diffraction method. The reason for this is presumably that it is a little too thick for synchrotron radiation measurements, and the large absorption cross section of the included boron-10 makes it difficult to obtain elastic scattering for neutron measurements. We prepared a wire substituted with boron-11, an isotope with small neutron absorption cross section, and attempted to measure its strain under tensile loading using pulsed neutron.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

Cyclic olefin copolymer (COC) is a novel type of thermoplastic polymer gaining the attention of the scientific community in electronic, optoelectronic, biomedicine and packaging applications. Despite the benefits in the use of COC like undoubted optical transparency, chemical stability, good water-vapor barrier and biocompatibility, its original hydrophobicity restricts its wider applicability and optimization of its performances. Presently, we report on the optical, and morphological properties of the films of COC covered with Ti in selected areas. The layer of Ti on COC was deposited by pulsed lased deposition processing. The Ti/COC film was characterized by UV-Vis spectroscopy indicating that its transmittance in the visible region decreased by about 20% with respect to the pristine polymer. The quality of the deposited Ti was assessed with the morphology by scanning electron (SEM) and atomic force microscopies (AFM). The modification of the wettability was observed by the sessile drop method indicating a reduction of the native hydrophilicity.

Highly efficient, broadband and distinctively structured electromagnetic wave (EMW) absorption materials exhibit huge exceptions with multi-functions in both military and civilian fields. Searching the relationship between structural and EMW performance is beneficial to develop outstanding microwave absorption materials, and has become an attractive research topic. In this study, we briefly reviewed the different EMW absorption mechanisms and key influence factors, then, present the latest developments in low-dimensional (LD) EMW absorption materials. We provide a comprehensive discussion of remarkable examples and summarize the main information related to the structure-function relationship of dimensional design and structural engineering in order to facilitate the rapid evolution of this fascinating field.

The combination of interstitial hyperthermia treatment (IHT) with high dose rate brachytherapy (HDR-BT) for prostate cancer treatment and has the potential to improve clinical outcome, since it highly enhances the efficiency of cell kill, especially when applied simultaneously. Therefore, we have developed the ThermoBrachy applicators. To effectively apply optimal targeted IHT, treatment planning is considered essential. However, treatment planning in IHT is rarely applied since it is regarded difficult to accurately calculate the deposited energy in the tissue in a short enough time for clinical practice. In this study, we investigated various time-efficient methods for fast computation of the electromagnetic (EM) energy deposition resulting from the ThermoBrachy applicators. Initially, we investigated the use of an electro-quasistatic solver. Next, we extended our investigation to the application of geometric simplifications. Furthermore, we investigated the validity of the superpositioning principle, which can enable adaptive treatment plan optimization without the need for continuous recomputation of the EM field. Finally, we evaluated the accuracy of the methods by comparing them to the golden standard Finite-Difference Time-Domain calculation method using gamma-index analysis. The simplifications considerably reduced the computation time needed, improving from &gt;12 h to a few seconds. All investigated methods showed excellent agreement with the golden standard by showing a &gt;99% passing rate with 1%/0.5 mm Dose Difference and Distance-to-Agreement criteria. These results allow the proposed electromagnetic simulation method to be used for fast and accurate adaptive treatment planning.

The development of novel coherent and brilliant sources, such as soft X-ray Free Electron Laser (FEL) and High Harmonic Generation (HHG) enables new ultrafast analysis of the electronic and structural dynamics of a wide variety of materials. Soft X-ray FEL delivers high brilliance beams with short pulse duration, high spatial coherence and photon energy tunability. In com-parison with FELs, HHG X-ray sources are characterized by a wide spectral bandwidth and few to sub-femtosecond pulses. The approach will lead to time-resolved reconstruction of molecular dynamics, shedding light on different photochemical pathways. The high peak brilliance of soft X-ray FELs facilitates investigations in nonlinear regime, while the broader spectral bandwidth of the HHG sources may provide the simultaneous probing of multiple components. Significant technical breakthroughs in these novel sources are under way to improve brilliance, pulse dura-tion, and to control spectral bandwidth, spot size, and energy resolution. Therefore, in the next few years, the new generation of soft X-ray sources combined with novel experimental tech-niques, new detectors, and computing capabilities will allow the study of several extremely-fast dynamics, such as vibronic dynamics. In the present review, we shortly discuss recent devel-opments in experiments, performed with soft X-ray FELs and HHG sources, operating near car-bon K-absorption edge, being a key atomic component in biosystems and soft materials. Differ-ent spectroscopy methods such as time-resolved pump-probe techniques, nonlinear spectrosco-pies and photoelectron spectroscopy studies have been addressed in an attempt of a better un-derstanding of fundamental physico-chemical processes

Magnesium nanoparticles of various mean diameters (53 – 239 nm) were synthesized herein via Pulsed Laser Ablation in Liquid (PLAL) from millimeter sized magnesium powders within iso-propyl alcohol. It was observed via a 3x3 full factorial DOE that the processing parameters can control the nanoparticle distribution to produce three size-distribution types (bimodal, skewed and normal). Ablation times of 2, 5, and 25 minutes where investigated. An ablation time of 2 minutes produced a bimodal distribution with the other types seen at higher periods of processing. Mg nanoparticle UV-Vis absorbance at 204 nm increased linearly with increasing ablation time, indicating an increase in nanoparticle count. The colloidal density (mg/ml) generally increased with increasing nanoparticle mean diameter as noted via increasing UV-vis absorbance. High la-ser scan speeds (within the studied range of 3000 - 3500 mm/s) tend to increase the nanoparticle count/yield. For the first time, the effect of scan speed on colloidal density, UV-vis absorbance and nanoparticle diameter from metallic powder ablation was investigated and is reported herein. The nanoparticles formed dendritic structures after being drop cast on aluminum foil as observed via FESEM analysis. Dynamic light scattering was used to measure the size of the nanoparticles. Magnesium nanoparticles have promising use in the fabrication of wearables, such as in conductive tracks or battery electrodes, owing to their low heat capacity, high melting point and bio-compatibility.

To address the challenges associated with the difficult electromagnetic (EM) scattering computations of anisotropic dielectric-coated metallic composite targets, we proposed an efficient hybrid algorithm for simulating the EM scattering of complex targets with anisotropic dielectric coatings. This method, based on Impedance Boundary Condition (IBC), utilizes surface impedance vectors to describe the EM properties of the dielectric. It fully leverages the respective advantages of the low-frequency Method of Moments (MoM) and the high-frequency Physical Optics (PO) to achieve high-precision and rapid EM simulation of anisotropic dielectric-coated metallic composite targets. Employing boundary conditions and equivalent principles, we equivalently transform the EM scattering problem of targets with thin dielectric coatings into the radiation problem of equivalent EM current on impedance surfaces. This enables the high-precision and rapid calculation of Radar Cross Sections (RCS) for complex targets with anisotropic dielectric coatings. Using examples such as a square plate structure, a simplified aircraft, and a complex satellite model, the simulation results exhibit a high degree of agreement with full-wave numerical solutions and demonstrate a significant advantage in computational resources. This research convincingly demonstrates the accuracy and effectiveness of the proposed method.

Electromagnetic (EM) waves, used for purposes such as geophysical characterization, impact properties to be measured. This paper describes the effects of radio frequency (RF) waves on the hydraulic conductivity of glass beads and natural sand. A series of tests were conducted using a customized, rigid-wall, cylindrical permeameter inside a resonant cavity made of Plexiglas covered with electrically conductive transparent films. Constant head ASTM-D2434 [1] tests were performed to measure the samples’ hydraulic conductivity. RF stimulation was performed using a magnetically coupled loop antenna at a constant frequency of 726 MHz and input power levels of 10, 25, 40, and 50 Watts. The hydraulic conductivity of both natural sand and glass-bead samples increased with RF stimulation. Furthermore, measurement of the electric-field component of RF waves was also performed to illustrate the pattern of the electric field as well as evaluate the RF impact on the hydraulic conductivity tests. The electric field was numerically simulated and validated against experimentally measured electric fields. A finite-difference numerical model was developed in MATLAB to analyze the seepage flow, which was then validated against the experimental results. An optimization scheme was then used to develop a governing equation for the RF impact on hydraulic conductivity.

As semi-airborne mineral exploration has limited budgets, it is critical to design experimental procedures that generate data maximizing the desired information We investigate the effects of transmitter-receiver geometries for a variety of anomalies and semi-airborne layouts. Our simulations indicate that 200 m flight line spacing and 100 m point distance are the optimal trade-off between coverage and survey progress for various targets. Based on the target size and distance between the transmitter and the target, the transmitter length should be at least equal to the length of the target and for more than 1 km, at least two or three times the target size. Likewise important are the location and direction of the transmitter cables, which can have great impact on the result of inversion and should be parallel to the target strike. By using more than one transmitter, better results are obtained. If the strike of the target is known, transmitters should be parallel to each other and if not, it is better to use perpendicular transmitters. Results showed that the optimal distance between transmitters is 3 km. Our simulations show that it is even possible to recover targets just below the transmitter in corresponding areas of masked data.

During the launch and return of a spacecraft, the intense combustion of propellants generates strong electromagnetic radiation, which interferes with the operation of electronic equipment in the spacecraft. To improve the electromagnetic compatibility of electronic equipment in spacecraft, it is necessary to study the electromagnetic radiation characteristics of rocket fuel. An electromagnetic radiation measurement system based on antennas is designed to measure the electromagnetic radiation generated by rocket fuel, and the electromagnetic radiation characteristics are obtained through data analysis. The mechanism of the electromagnetic radiation generated by rocket fuel is comprehensively analysed through the spatial, time-domain, frequency-domain, and energy-domain characteristics. A characterization model is established to provide a reliable scheme for evaluating the influence of rocket fuel electromagnetic radiation on electronic equipment in spacecraft.

Silver particles are prepared by dewetting Ag films coated on glass using a fiber laser. The size of the particles is controlled in the range of 92 nm ~ 1.2 μm by adjusting the thickness of the Ag film. The structural properties and surface roughness of the particles are evaluated by means of scanning electron microscopy. In addition, the antifungal activity of the Ag particles is examined using spore suspensions of Colletotrichum gloeosporioides. It is shown that the particles with a size of 1.2 μm achieve 100% inhibition of the conidia growth of the Colletotrichum gloeosporioides after a contact time of just 5 min. Furthermore, the smaller particles also achieve a good antibacterial activity given a longer contact time. Similar results are observed in spore germination and pathogenicity tests performed on mango fruit and leaves. Overall, the results confirm that the Ag particles have an excellent antifungal effect on Colletotrichum gloeosporioides.

Structure quality of LuFeO3 epitaxial layers grown by pulsed-laser deposition on sapphire substrates with and without platinum interlayers has been investigated by in-situ high-resolution x-ray diffraction (reciprocal-space mapping). The parameters of the structure such as size and misorientation of mosaic blocks have been determined as functions of the thickness of LuFeO3 during the PLD growth and for different platinum interlayers thicknesses up to 40 nm. The x-ray diffraction results combined with ex-situ scanning electron microscopy and high-resolution transmission electron microscopy demonstrate that the Pt interlayer significantly improves the structure of LuFeO3 by reducing the misfit of the LuFeO3 lattice with respect to the material underneath.

Purpose: A number of imaging readout schemes have been proposed for renal arterial spin labelling (ASL) to quantify kidney cortex perfusion, including gradient echo based methods of balanced fast field echo (bFFE) and gradient-echo echo-planar imaging (GE-EPI), or spin echo based schemes of spin-echo echo planar imaging (SE-EPI) and turbo spin-echo (TSE). Here, we compare these imaging schemes to evaluate the optimal imaging scheme for pulsed ASL (PASL) assessment of human kidney cortex perfusion at 3 T. Methods: Ten healthy volunteers with normal renal function were scanned using each 2D multislice imaging scheme, in combination with a respiratory triggered FAIR (flow-sensitive alternating inversion recovery) ASL scheme on a 3 T Philips Achieva scanner. All volunteers returned for a second identical scan session within two weeks of the first scan session. Comparisons were made between the imaging schemes in terms of perfusion weighted image (PWI) signal-to-noise ratio (SNR) and perfusion quantification, temporal SNR (tSNR), spatial coverage, and repeatability. Results: For each imaging scheme, renal cortex perfusion was calculated (bFFE: 276 ± 29 mL/100 g/min, GE-EPI: 222 ± 18 mL/100 g/min, SE-EPI: 201 ± 36 mL/100 g/min, TSE: 200 ± 20 mL/100 g/min). Perfusion was found to be higher for GE based readouts compared to SE based readouts, with significantly higher measured perfusion for the bFFE readout compared to all other schemes (P < 0.05), attributed to the greater vascular signal present. Despite the PWI-SNR being significantly lower for SE-EPI compared to all other schemes (P < 0.05), the SE-EPI readout gave the highest tSNR and was found to be the most reproducible scheme for the assessment of kidney cortex, with a CoV of 17.2%, whilst minimizing variability of the perfusion weighted signal across slices for whole kidney perfusion assessment. Conclusion: For the assessment of kidney cortex perfusion, SE-EPI provides optimal tSNR, minimal variability across slices and repeatable data acquired in a short scan time with low specific absorption rate.

The present paper reports an exact approach quantifying the electromagnetic contribution to the anomalous magnetic moment occurring in isolated system comprised of non-composite particle carrying elementary electric charge. Essential averaging procedure and regularization of the electromagnetic field potentials necessary when quantifying the electromagnetic self-interactions and when deriving equations of motion without singularities and obeying the conservation laws are thoroughly discussed. The study shows that the dynamics of the considered system is associated to unique classical transcendental equations of motion satisfied by the particle's velocity and the electromagnetic contribution to the anomalous $g$-factor known from the quantum electrodynamics. The equations of motion lead to an exact analytical expression for the anomalous $g$-factor that provides more accurate result than that calculated with the aid of quantum electrodynamics. It matches the experimentally measured value reported in the literature to a one part per trillion. We obtain a_e=0.00115965218000(65) thus reveling the potential of non-perturbative, non-probability methods in predicting the electron's anomalous g-factor.

The propagation of electromagnetic waves beyond the line of sight can be caused by atmospheric ducts, which are a significant concerns in the fields of radar and communication. This paper utilizes data from seven automatic stations and five radio-sounding stations to statistically analyze the characteristics of the atmospheric ducts in the northwest region of the South China Sea (SCS). After verifying the practicality of numerical analysis data from NCEP CFSv2 and ERA5 in studying atmospheric ducts using measured data, we analyzed the space-time distribution characteristics of the height of the regional evaporation duct and the bottom height of the elevated duct. Using the parabolic equation model, we simulated electromagnetic propagation loss under different frequencies and radiation elevation angles in both uniform and non-uniform duct environments within a typical atmospheric duct structure. The study found that the NCEP CFSv2 data accurately captures the evaporation duct height and duct occurrence rate in the study area, and the elevated duct bottom height obtained from the inversion of ERA5 and the measured data has a good consistency. The occurrence rate and height of evaporation duct in coastal stations in the northwest of the SCS vary significantly by month, demonstrating clear monthly distribution patterns. Conversely, changes in the Xisha station are minimal, indicating good temporal uniformity. For lower atmospheric ducts, the difference in occurrence rates between 00:00 and 12:00 (UTC) is negligible. The occurrence probability of elevated ducts in the Beibu Gulf area is relatively high, mainly concentrated from January to April, and the Xisha area is dominated by surface ducts without foundation layer, mainly concentrated from June to August. The monsoon plays a critical role in the generation and evolution of atmospheric ducts in the northwest of the SCS, with the height of the evaporation duct increasing and the bottom height of the elevated duct decreasing after the onset of the summer monsoon. Electromagnetic propagation simulations demonstrate that higher frequency and lower elevation angles of radiation sources in the trapping layer of the evaporation duct make it easier to be trapped. As the evaporation duct height decreases, the amplitude of the "sinusoidal fluctuation" of the propagation loss also decreases. Frequency changes of the radiation source in the surface duct environment have minimal impact on electromagnetic propagation loss, but the elevation angle of the radiation source is a critical factor. The frequency of the "sinusoidal fluctuation" in propagation loss is higher in a hybrid duct environment compared to a uniform surface duct. Additionally, the propagation loss increases faster with distance at the height of the evaporation duct, resulting in greater electromagnetic propagation loss.

We examine here characteristics of electromagnetic waves that propagate through an unbounded space filled with a homogeneous isotropic chiral medium. Resulting characters are compared to those of the electromagnetic waves propagating through an achiral free space. To this goal, we form energy conservation laws for key bilinear parameters in a chiral case. Due to a nonzero medium chirality, conservation laws turn out to contain extra terms that are linked to the spin-orbit coupling, which is absent for an achiral case. As an example, we take a plane wave for achiral case to evaluate those bilinear parameters. Resultantly, the conservation laws for a chiral case are found to reveal inconsistencies among several bilinear parameters that constitute the con-servation laws , thereby prompting us to establish partial remedies for formulating proper wave-propagation problems.

This article is a big picture of how electrical noise or conducted Electromagnetic Interference (EMI) is generated and mitigated in power converters. It gives an overview of what EMI in power converters is – from generation through to conduction and mitigation. It is meant to cover the complete subject as a summary so that the reader will have an outline of how to control conducted EMI by design (where possible) and how to mitigate by filtering. A clear distinction is made between Differential Mode (DM) and Common Mode (CM) EMI generation and mitigation. By using a boost converter as an example the trade-offs for DM noise control are discussed. It is shown how CM EMI is generated in a boost converter using the concept of the “Imbalance Difference Model” (IDM). Practical measurements for an in-line power filter is given showing the effect of the filter on the total EMI of a boost converter. Measurements for the CM current produced due to the imbalance difference for different values of the boost conductor are also shown. The main contribution of this study is linking CM noise generation to DM EMI. It is shown that CM noise is a direct consequence of DM noise (although circuit imbalance and coupling to a common ground also play a role). This paper will be useful to designers seeking the “bigger picture” of how EMI is generated in power converters and what can be done to mitigate the noise.

Negative corona discharges occur widely in high voltage transmission lines and charged aircraft, which can cause strong electromagnetic interference. Negative corona discharge is typically performed simultaneously at multiple discharge points. In this study, the current and its EM radiation characteristics of single-needle and multi-needle negative corona discharge in different conditions were tested. The current and electromagnetic radiation characteristics of the two discharge structures were compared. The dipole radiation model was established to analyze the EM radiation characteristics of the negative corona discharge.The results show that, It is only when the voltage reaches a certain threshold that the current and electromagnetic radiation fields of the multi-needle discharge structure will be superimposed and their amplitudes will increase significantly. The frequency of electromagnetic radiation signal does not change with the number of needles, cathode geometry and applied voltage, but only depends on ambient pressure. It provides a basis for detecting corona discharge sources under different conditions.

The aim of this work was to determine the potential of using a pulsed electric field (PEF) and ultra-sound (US) apparatus to produce mitragynine extracts from Mitragyna speciosa dried leaves. Four modes of the device were tested: PEF, US, US + PEF, and PEF + US. The results were compared with extracts obtained using a conventional technique (maceration, as the control). Changes in the mitragynine content were determined with the liquid chromatography/mass spectrometry (LC-MS/MS) method. The LC-MS/MS analysis showed that the mitragynine contents from kratom extracts using four different modes were different. The highest extraction (106.63 ± 0.85 mg/L) of mitragynine was achieved by the PEF + US procedure, followed by US + PEF (97.27 ± 1.33 mg/L), with increased extraction efficiencies of 45.81 ± 0.59% and 33.00 ± 1.85%, respectively. Moreover, the total energy consumption under the combination technique was 25.0% lower than that with PEF assistance. Furthermore, scanning electron microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR) provided confirmatory evidence for the extraction of M. speciosa by the prototype. This study confirmed that PEF and US devices can be considered a green alternative method and may contribute to the application of agricultural products.

In the provinces of the region, empirical constructions reached maximum points with these practices. The effects and pathologies appear as physical, chemical and mechanical failures in pillars, walls and roofs, generating uncertainty for the user. The current powerful design can detect the interior deterioration of coatings in adobe, brick and concrete constructions, and prevent collapses, material and economic losses. Experimental methods performed affirm the serious validity. The accuracy of the simulation and design provide a pre-test reliability of 95%. Five piles constructed of various materials participate in the prototype performance test, there is a correlation (R=0.9997) between the magnetic field range "B" (cm) and density "ρ" (g/cm³), also by increasing the current (i) in transit Q1 and coil L1, the induction of the "B" increases proportionally until penetrating the density of the wall of the building, having 5% reading error.

With the ongoing fifth-generation cellular network (5G) deployment, electromagnetic field exposure has become a critical concern. However, measurements are scarce, and accurate electromagnetic field reconstruction in a geographic region remains challenging. This work proposes a conditional Generative Adversarial Network to address this issue. The main objective is to reconstruct the electromagnetic field exposure map accurately according to the environment’s topology from a few sensors located in an outdoor urban environment. The model is trained to learn and estimate the propagation characteristics of the electromagnetic field according to the topology of a given environment. In addition, the conditional Generative Adversarial Network based electromagnetic field mapping is compared with simple kriging. Results show that the proposed method produces accurate estimates and is a promising solution for exposure map reconstruction.

The well-known coupling between the magnetic and electric fields in electromagnetic radiation is revisited in light of the recent introduction of a microscopic theory for the Ørsted magnetic field induction. I argue that, if the Ørsted magnetic field induction does indeed have a microscopic origin rather than the continuum solution offered by the Maxwell-Ampere equation, the "electromagnetic wave"' propagating in vacuum will not have a magnetic component.

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

The objective of this paper is to present an electromagnetic sensor that generates pulse inductance [1], integrated on an Unmanned Aerial Vehicle (UAV) which complements the current technology in this area, adding equipment to the detection of landmines. The electromagnetic sensor developed, locates landmines deployed during armed conflicts, which daily kill innocent people, block economic and social development, hinder the displacement of people, causing serious social and economic problems for many years. Flights can be made over mined areas allowing the identification of the exact location of each land mine.

Pulsed thermography is a commonly used non-destructive testing method, and is increasingly studied for advanced materials such as carbon fiber-reinforced polymer (CFRP) evaluation. Different processing approaches are proposed to detect and characterize anomalies that may be generated in structures during the manufacturing cycle or service period. In this study, we used a type of matrix decomposition using Robust-PCA via Inexact-ALM in our experiment. We investigate this method as a pre-and post-processing method on thermal data acquired by pulsed thermography. We employed state-of-the-art methods, i.e., PCT, PPT, and PLST, as the main process. The results indicate that pre-processing on thermal data can elevate the defect detectability while post-processing, in some cases, can deteriorate the results.

Extracorporeal shock wave therapy (ESWT) is a well investigated and widely used treatment modality for a number of musculoskeletal disorders. A limitation of ESWT is its potential painfulness at higher, clinically relevant energy flux density (EFD), which may limit its applicability and, thus, effectiveness. Various studies in the literature demonstrated that neither application of a higher number of extracorporeal shock waves with lower EFD nor use of local anesthesia may solve this problem. Based on the results of several other studies in the literature it is hypothesized here that in patients suffering from musculoskeletal disorders that can be treated with ESWT, pretreatment with a pulsed, high power laser with a wavelength of 904 or 905 nanometers (hereafter: "laser pretreatment") does not only allow to apply higher EFDs in subsequent ESWT but actually results in faster and/or better treatment outcome than ESWT without laser pretreatment. Accordingly, it is hypothesized here that combining ESWT with laser pretreatment leads to synergistic effects and, thus, is superior to either treatment modality alone. Confirming this hypothesis in preclinical and clinical research may raise significance and increase the use of ESWT in physical and rehabilitation medicine, with immediate benefit for patients.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

The goal of this paper is to present a low-cost, low-power prototype of a pulsed Ultra Wide Band UWB) oscillator and an UWB elliptical dipole antenna integrated on the same Radio Frequency (RF) Printed Circuit Board (PCB) and its digital control board for Real Time Locating System (RTLS) applications. The design is compatible with IEEE 802.15.4 high rate pulse repetition UWB standard being able to work between 6 GHz and 8.5 GHz with 500 MHz bandwidth and with a pulse duration of 2 ns. The UWB system has been designed using the CST Microwave Studio transient Electro-Magnetic (EM) circuit co-simulation method. This method integrates the functional circuit simulation together with the full wave (EM) simulation of the PCB’s 3D model allowing fast parameter tuning. The PCB has been manufactured and the entire system has been assembled and measured. Simulated and measured results are in excellent agreement with respect to the radiation performances as well as the power consumptions.

This study delves into the intricate relationships among the constituent elements, wave speed, and energy of both mechanical waves and electromagnetic waves. By establishing connections with the string vibration equation, a compelling revelation emerges. Upon equating the energy and constituent element mass of one wave cycle of a homogeneous string with those of a single wave cycle of electromagnetic waves, it is evident that the wave speed derived from the string vibration equation consistently matches the constant speed of light. From this, a hypothesis takes root: electromagnetic waves manifest as waves resulting from the vibration of a uniform, elongated string-like material. The phenomenon of superluminal speed further fortifies the validity of this conjecture.

Electromagnetic actuation can support many fields of technology, such as robotics or biomedical applications. In this context, fully understanding the system behavior and proposing a low-cost package for feedback control is challenging. Modeling the electromagnetic force is particularly tricky because it is a nonlinear function of the actuated object’s position and coil’s current. Measuring in real time the position of the actuated object with the precision required for accurate motion control is also nontrivial. In this study, we propose a novel, cost-effective electromagnetic set-up to achieve position control via visual feedback. We actuate vertically and under different experimental conditions a 10 mm diameter steel ball hanging on a low-stiffness spring, demonstrating good tracking performance (the position error remains within ±0.5 mm with a negligible phase delay in the best scenarios). The experimental results confirm the feasibility of the proposed set-up, which is characterized by minimum complexity and realized with off-the-shelf and cost-effective components. For these reasons, such a contribution helps to understand and apply electromagnetic actuation even further.

In this study, the temporal variation in soil salinity dynamics was monitored and analyzed using Electromagnetic Induction (EMI) in an agricultural area in Port Said, Egypt, which is at risk of soil salinization. To assess soil salinity, repeated CMD2 soil apparent electrical conductivity (ECa) measurements were taken and inverted to generate electromagnetic conductivity imaging (EMCI), representing soil electrical conductivity (σ) distribution through time-lapse inversion. This process involved converting EMCI data into salinity cross sections using a site-specific calibration equation that correlates σ with the electrical conductivity of saturated soil paste extract (ECe) for the collected soil samples. The study was performed from August 2021 to April 2023, involving six surveys during two agriculture seasons. The results demonstrated the accurate prediction ability of soil salinity with R2 value of 0.81. The soil salinity cross sections generated on different dates observed changes in the soil salinity distribution. These changes can be attributed to shifts in irrigation water salinity resulting from canal lining, winter rainfall events, and variations in groundwater salinity. This approach is effective for evaluating agricultural management strategies in irrigated areas where it is necessary to continuously track soil salinity to avoid soil fertility degradation and a decrease in agricultural production and farmer’s income.

The paper is focused on numerical modeling of multi-strand cable lines placed in free air. Modeling is carried out within the framework of the so-called multi-physics approach using commercial software. The paper describes in detail the steps undertaken to develop realistic, reliable numerical models of power engineering cables, taking into account their geometries and heat exchange conditions. The results might be of interest to the designers of multi-strand cable systems.

Recently, Bennett et al. [Eur. J. Phys. 37:014001, 2016] presented a physically-motivated and explicitly gauge-independent scheme for the quantisation of the electromagnetic field in flat Minkowski space. In this paper we generalise this field quantisation scheme to curved spacetimes. Working within the standard assumptions of quantum field theory and only postulating the physicality of the photon, we derive the Hamiltonian, $\hat H$, and the electric and magnetic field observables, $\hat {\bf E}$ and $\hat {\bf B}$, without having to invoke a specific gauge. As an example, we quantise the electromagnetic field in the spacetime of an accelerated Minkowski observer, Rindler space, and demonstrate consistency with other field quantisation schemes by reproducing the Unruh effect.

As we all know, contemporary electromagnetic theory is based on the macroscopic electromagnetic theory established by the 19th century. Because of the lack of microscopic cognition in that era, various electromagnetic phenomena could only be explained and described at the macro level, and their origins could not be explained at the micro level. And because of the microscopic understanding of atomic physics in the 20th century, new progress has been made. Considering that it is now the 21st century, this paper attempts to establish a new theory of microscopic interpretation of classical electromagnetic theory based on the new cognition of atomic physics in the 20th century. Starting from the general assumption, the current will be interpreted as the momentum flow produced by the directed collision between electrons; the charge will be interpreted as a form of expression of electron motion; the voltage is interpreted as the potential difference (energy level difference) of the electron orbit. In the end, this paper successfully developed a new microscopic electromagnetic theory by introducing microscopic atomic physics and rigid body mechanics models to Maxwell's macroscopic electromagnetic theory.

A novel method proposed in the production of Calophyllum inophyllum biodiesel has been investigated experimentally. In this study, we report the results of biodiesel processing with electromagnetic induction technology. The method used is to compare the results of Calophyllum inophyllum biodiesel processing between conventional, microwave and electromagnetic induction. The degumming, transesterification, and esterification process of the 3 methods are measured by stopwatch to obtain time comparison data. Characteristics of viscosity, density, and Fatty Acid Metil Ester (FAME) were obtained from testing of a Gas Chromatography-mass Spectrometry (GCMS) at the Polytechnic Chemistry Laboratory of the State of Malang. The results show that the biodiesel produced by this method satisfies the biodiesel standards and their characteristics are better than the biodiesel produced by conventional and microwave methods. The electromagnetic induction method also offers a fast and easy route to produce biodiesel with the advantage of increasing the reaction rate and improving the separation process compared to other methods. This advanced technology has the potential to significantly increase biodiesel production with considerable potential to reduce production time and costs.

In this paper analyses the characteristic of EM waves propagation in structured environment to identify the signal interference by the structure, and suggests the EM waves attenuation model considering the distance and penetration loss by the structure. The range sensor based on electromagnetic(EM) waves attenuation along to the distance showed the precise distance estimation with high resolution depending on the distance. However, it is hard to use in structured environments due to the lack of consideration of the EM waves attenuation characteristics in the structured underwater environment. In this paper, EM waves propagation characteristic and signal interference effects by the structures were analyzed, and the EM waves distance-attenuation model in structured environment was suggested with sensor installation guideline. The EM waves propagation characteristics and proposed sensor model were verified by the several experiments, and the localization result in structured environment showed the more reliable performance.

In this paper, an original approach allowing the determination of the iron losses in the electromagnetic devices is presented. This new approach exploits the Loss Surface (LS) hysteresis model and the magnetic flux density waveforms resulting from a generalized nonlinear adaptive magnetic equivalent circuit (MEC) using a mesh-based formulation in two-dimensional (2-D) or quasi three-dimensional (3-D). The model coupling has been applied to a 18-slots/16-poles radial-flux interior permanent-magnet (PM) synchronous machine (PMSM) dedicated to automotive applications, mainly for electric/hybrid/fuel cell vehicles (EVs/HEVs/FCVs). The obtained results have been compared with those made retrospectively in the 2-D transient finite-element (FE) Flux. The influence of the MEC discretization on the iron loss calculation and the electromagnetic performances has been analyzed. The computation time is divided by 3/2 with an error less than 7 %.

An ultraviolet (UV) nanosecond pulsed laser with a wavelength of 355 nm was applied to anneal amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFT) at various laser beam powers ranging from 0 to 280 mW. Laser irradiation was selectively carried out on the a-IGZO channel area using the beam scanning method after the a-IGZO TFT was formed through indium-tin oxide (ITO) electrode patterning and a subsequent lift-off process. After laser annealing, negative shifts in the threshold voltages and enhanced on-currents were observed at laser-beam powers ranging from 54 to 120 mW. No meaningful parameters were investigated for laser beams higher than 200 mW. By extracting the energy band gap and work function of a-IGZO from the transmittance and ultraviolet photoelectron spectroscopy (UPS) results, the ITO electrode/a-IGZO channel energy band structures were established under different laser annealing conditions, and the electron injection mechanism from the ITO to the a-IGZO channel was analyzed and optimized at a laser beam power of 120 mW. The results show that the electrical characteristics of the a-IGZO TFTs can be improved without any heat damage to the substrate because of the selective annealing process.

We presents results obtained from the numerical simulation of the gas-phase chemical kinetics in atmospheric pressure air non-equilibrium plasmas. In particular we have addressed the effect of pulsed operation mode of a planar dielectric barrier discharge. As it was conjectured, the large difference in the time scales involved in the fast dissociation of molecules in plasmas and their subsequent reactions to produce stable chemical species, makes the presence of a continuously repeated plasma production stage unnecessary and a waste of electrical power and efficiency. Results on NOx remediation, ozone production, water vapor and ammonia dissociation are discussed. A few comparisons with experimental findings in a dielectric barrier discharge reactor already used for applications is briefly addressed too. Our results clearly indicate a pattern for the optimization of the discharge using a carefully designed repetition rate and duty-cycle.

Ultrasonic imaging & NDE applications can greatly improve their signal-to-noise ratios (SNR) by driving each transducer (composing piezoelectric arrays) with a spike giving pulsed power of k-Watts, repetitively at a PRF = 5000 spikes/s, by using a HV capacitive-discharge generator. However very-high levels, of pulsed intensities (3-10 A) and voltages (300-700 V) must be considered for a rigorous spike modeling. Even though the consumed "average" power will be small, the intensity through each transducer achieves several amperes, so the pulsed powers delivered by each HV generator can attain levels higher than in CW high-power ultrasonic applications: e.g., up to 5 kW / spike. This is concluded here from a transient modeling of the loaded generator. Then, unforeseen phenomena rise: intense brief pulses of driving power & emitted force in transducers, and non-linearities in driver semiconductors, because their characteristic curves only include linear ranges. But fortunately, piezoelectric devices working in this intense regime do not show serious heating problems, because the average power remains being moderate. Intensity, power and voltage, driving a broadband transducer from a HV capacitive pulser, are calculated to drastically improve (in ≅ 40 dB) the ultrasonic net dynamic range available, with emitted forces ≅ 250 Newtons pp and E/R received pulses of 70 V pp.

We utilized laser irradiation as a potential technique in tuning the electrical performance of NiOx/SiO2 thin film transistors (TFTs). By optimizing the laser fluence and the number of laser pulses, the TFT performance is evaluated in terms of mobility, threshold voltage, on/off current ratio and subthreshold swing, all of which were derived from the transfer and output characteristics. The 500 laser pulses irradiated NiOx/SiO2 TFT exhibited an enhanced mobility of 3 cm2/V-s from a value of 1.25 cm2/V-s for as-deposited NiOx/SiO2 TFT. The laser-irradiated NiOx material likely has a significant concentration of defect gap states, which could also be involved in light absorption processes. Second, and more importantly, the excess energy that the photogenerated charge carriers possess (due to the significant difference between the photon energy and the bandgap of NiOx), combined with the very high light intensity, would result in complex thermal and photo thermal changes thus resulting in an enhanced electrical performance of p-type NiOx/SiO2 TFT structure.

We consider the Dirac electron as a nonperturbative particle-like solution consistent with its own Kerr-Newman (KN) gravitational and electromagnetic field. We develop the earlier models of the KN electron regularized by Israel and López, and consider the non-perturbative electron model as a bag model formed by Higgs mechanism of symmetry breaking. The López regularization determines the unique shape of the electron in the form of a thin disk with a Compton radius reduced by 4π. In our model this disk is coupled with a closed circular string which is placed on the border of the disk and creates the caused by gravitation frame-dragging string tension produced by the vector potential of the Wilson loop. Using remarkable features of the Kerr-Schild coordinate system, which linearizes the Dirac equation, we obtain solutions of the Dirac equation consistent with the KN gravitational and electromagnetic field, and show that this solution takes the form of a massless relativistic string. Parallelism of this model with quantum representations in Heisenberg and Schrodinger pictures explains remarkable properties of the stringy electron model in the relativistic scattering processes.