The process of rainfall interception by tree organs is crucial in mitigating the impact of intense rainfall on urban drainage systems, particularly in the context of climate change. this study selected ten commonly found tree species in Shanghai. Main parts of trees, including leaves, branches, and bark, were collected to analyze their ability to intercept rainwater. The optimized Artificial Rainfall Simulation System (ARSS) was applied to simulate the rainfall. The time-changing process of rainwater interception in three organs was measured during a 180-minute rainfall event which under four different rainfall intensities (4, 8, 12, and 16 mm/h, respectively). Process models of rainwater interception in different organs were fitted with adsorption kinetic equations. The rainwater interception process of tree organs complied with the quasi 2nd-order adsorption kinetic equation. The rainwater interception capacity of leaves, branches, and bark of ten urban tree species ranged from 0.05 to 0.34 mm, 0.13 to 0.24 mm, and 0.29 to 1.22 mm, respectively. The rainwater interception capacity of three organs significantly differs (p<0.05). It reveals that bark exhibits the highest rainwater interception ability. Coniferous tree species have a greater ability to intercept rainwater than broad-leaved tree species. There are also differences in the rainwater interception ability of trees in urban and natural areas.

Water is essential for living organisms. The increase in world population, global climate change and rapid growth in industrialization and urbanization have brought with them water issues around the world in recent years. Not only should existing water resources be used reasonably and efficiently but alternative water resources should also be explored and secured. Rainwater harvesting, which is one of the alternative water resources, can provide economic and environmental solutions. For rainwater harvesting, the size of reservoirs in which rainwater captured from roof catchments is stored should be determined. Determining the optimum tank capacity depending on precipitation and consumption rates allows us to make maximum use of rainwater tanks. The aim of this study is to determine the optimum tank capacity for the storage of rainwater captured from roof catchments in order to meet the water demand for agricultural production. Precipitation data were collected from the city of Isparta and its districts. Rainwater tank capacity was determined using the Rippl, residual mass curve, minimum flow and particle swarm optimization methods. Storage capacities varying according to roof areas and consumption rates are shown in a graph. Results show that particle swarm optimization is the best method.

This research presents a novel algorithmic implementation to improve the analysis of visually controlled interception and accompanying motor action through the computational application of harmonic ratios and stimulation invariants. Unlike traditional models that focus mainly on psychological aspects, our approach integrates the relevant constructs into a practical mathematical framework. This allows for dynamic prediction of interception points with improved accuracy and real-time perception-action capabilities, essential for applications in neurorehabilitation and virtual reality. Our methodology uses stimulation invariants as key parameters within a mathematical model to quantitatively predict and improve interception outcomes. The results demonstrate the superior performance of our algorithms over conventional methods, confirming their potential for ad-vancing robotic vision systems and adaptive virtual environments. By translating complex theo-ries of visual perception into algorithmic solutions, this study provides innovative ways to im-prove motion perception and interactive systems. This study aims to articulate the complex inter-play of geometry, perception, and technology in understanding and utilizing cross-ratios at infin-ity, emphasizing their practical applications in virtual and augmented reality settings.

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

This study estimates rainfall interception losses from natural wetland ecosystems based on maximum canopy storage measurements. Rainfall interception losses play an important role in water balance, which is crucial in wetlands, and has not yet been thoroughly studied in relation to this type of ecosystem. Maximum canopy storage was measured using the weight method. Based on these measurements, daily values of interception losses were estimated and then used to calculate long term interception losses based on precipitation and potential evapotranspiration data for the 1971–2015 period. Depending mainly on the number of days with precipitation, the results show that total interception losses for the growing season as well as monthly interception losses are around 13% of gross rainfall. This value is similar to the values observed for some forests. Hence, interception losses should not be disregarded in hydrologic models of wetlands, especially because data trends in meteorological conditions (mainly number of days with precipitation) show that interception losses will increase in the future if those trends stay the same.

Optical backbone networks constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is a key factor influencing optical network performance, it is important to understand how topological and physical properties impact its behavior and to have the capability to estimate its value. In this context, we propose here a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with constrained routing techniques for traffic routing. As this type of routing can lead to traffic blocking, particularly due to the limitation on the number of wavelengths per fiber, we also propose a fiber assignment algorithm designed to deal with this problem. We apply this method to a set of randomly generated networks using a modified Waxman model, and for a network with 60 nodes, in a scenario without blocking, we obtain capacities of about 2.5 Pbit/s for a symbol rate of 64 Gbaud and about 5 Pbit/s for a symbol rate of 128 Gbaud. Remarkably, this duplication in the total network capacity is achieved by an increase in the total fiber length of only about 51%.

Urban water management rules have long been oriented towards the rapid disposal of rainwater and wastewater through combined or separate drainage networks. This type of urban water management has shown its limits in both developed and undeveloped countries, notably because of its inexorable degradation over time and the cost of its rehabilitation and adaptation to the increase in demand due to urban growth. Sanitation data from the Office Nationale de l’Assainissement du Sénégal. Rainfall data are processed and analyzed to describe the current situation and how variable and high rainfall affects the neighborhood. Approximately 70-92% of the Dakar region's inhabitants have on-site sanitation facilities and sufficient income makes it difficult to manage their wastewater without exposing the environment or the health of citizens. The volumes of domestic wastewater flowed into the environment, in addition to poorly evacuated rainwater, show that the current sanitation system in the Dakar region is largely outdated, and insufficient for an effective drainage of rainwater and wastewater. Increasingly, frequent flash floods of polluted storm water from large amounts of domestic sewage are occurring, resulting in damage to human health. Exceptionally high rainfall is in correlation with high daily rainfall, therefore in recent years daily rainfall higher than 100 mm have been recorded in connection with above-average annual rainfall. That increase in rainfall disrupts the drainage of wastewater in the region of Dakar. A pragmatic and voluntary policy based on the principles of ecohydrology to recreate natural areas will be the only way for Dakar to efficiently manage storm water and wastewater. It can bring Dakar in 2030 into the international group of sustainable green cities.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

This paper reviews the design and component of two types of RWHS, namely roof harvesting system (RHS) and pond harvesting system (PHS). The performance in terms of quantity and quality of collected rainwater and energy consumption for RWHS with different capacities were evaluated, as well as the benefits and challenges particularly in environmental, economic and social aspects. Presently, RHS is more commonly applied but its effectiveness is limited by its small scale. The PHS is of larger scale and has greater potentials and effectiveness as an alternative water supply system. Results also indicate the many advantages of PHS especially in terms of economics, environmental aspects and volume of water harvested. While RHS may be suited to individual or existing buildings, PHS has greater potentials and should be applied in newly developed urban areas with wet equatorial climate.

Background: Mental capacity is a fundamental aspect that enables patients to fully par-ticipate in various healthcare procedures. To assist healthcare professionals (HCPs) in assessing patients' capacity, especially in the mental health field, several standardized tools have been developed. These tools include the MacArthur Competence Assessment Tool for Treatment (MacCAT-T), the MacArthur Competence Assessment Tool for Clinical Research (MacCAT-CR), and the Competence Assessment Tool for Psychiatric Advance Directives (CAT-PAD). The core dimensions explored by these tools include Understanding, Appreciation, Reasoning, and Expression of a choice. Objective: This meta-analysis aimed to investigate potential differences in deci-sion-making capacity within the healthcare context among groups of patients with bi-polar disorder (BD) and schizophrenia spectrum disorder (SSD). Methods: A systematic search was conducted on Medline/Pubmed, and Scopus. Addi-tionally, Google Scholar was manually inspected, and a manual search of emerging re-views and reference lists of the retrieved papers was performed. Eligible studies were specifically cross-sectional, utilizing standardized assessment tools, and involving pa-tients diagnosed with BD and SSD. Data from the studies were independently extracted and pooled using random-effect models. Hedges g was used as a measure for outcomes. Results: Six studies were identified, with three studies using the MacCAT-CR, two studies the MacCAT-T, and one the CAT-PAD. The participants included 189 individuals with BD and 324 individuals with SSD. The meta-analysis revealed that patients with BD performed slightly better, and the difference was statistically significant, compared to patients with SSD, particularly in the domain of Appreciation (ES=0.23, 95% CI: 0.01 to 0.04, p=0.037). There was no statistically significant difference between the two groups for Understanding (ES=0.09, 95% CI: - 0.10 to 0.27, p=0.352), Reasoning (ES=0.18, 95% CI: - 0.12 to 0.47, p=0.074), and Expression of a choice (ES = 0.23, 95% CI: - 0.01 to 0.48, p=0.60). In the sensitivity analysis, furthermore, when considering only studies involving patients in symptomatic remission, the difference for Appreciation also resulted in non-significant (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). Conclusions: These findings indicate that there are no significant differences between patients with BD and SSD during remission phases, while differences are minimal during acute phases. The usefulness of standardized assessment of capacity at any stage of the illness should be considered, both for diagnostic-therapeutic phases and for research and advance directives. Further studies are necessary to understand the reasons for the overlap in capacity between the two diagnostic categories compared in this study.

The reserves of water, which is one of the most important requirements for human life, gradually decreases under current conditions and rapidly depletes despite being one of the renewable resources. Considering the global water reserves, it became imperative to implement measures to protect the anticipated water reserves. The fact that the amount of quality water per capita decreases every day in the world and the increasing competition in water management could be considered among the indicators of the above-mentioned case. In recent years, as the effects of this adversity became increasingly more evident, several sustainable methods were adopted all over the world such as rain gardens and rainwater storage facilities. These sustainable techniques could be observed in many areas, especially in urban centers. In the present study, the area with the highest water collection was determined at Karadeniz Technical University Kanuni Campus and identified as the study area. Precipitation per square meter and surface runoff volume were identified based on the GIS (Geographic Information System) data, annual water collection volume was calculated, and information on economic and ecological recycling of the water was provided. In conclusion, the precipitation data for 11 years were compared, and it was calculated that the average annual precipitation was 64.06 kg/m² and annual surface runoff water was 552.77 m³. Based on the surface runoff water volume in the months when no irrigation is conducted, a reservoir was designed under the vehicle road and water recycling recommendations were developed.

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

The objective of this paper is to assess the potential for potable water savings due to rainwater use in a precast concrete factory in southern Brazil. The economic feasibility and the rainwater quality were also assessed. The current water consumption, future water demand and rainwater demand in the factory were estimated. The future demand considered was two times higher than the current water consumption since there are plans to increase the production. Three scenarios were then simulated using the computer programme Netuno. The ideal rainwater tank capacity, the potential for potable water savings and the economic feasibility analysis for each scenario were estimated. Samples of rainwater were collected in the factory and tested for quality for manufacturing precast concrete. For a rainwater tank capacity equal to 25,000 litres, the potential for potable water savings for the first scenario was 55.4%, but the first scenario was considered economically unfeasible. For the same tank capacity, the second and third scenarios presented viable results regarding potable water savings and payback. As for the rainwater quality, it was proven to be adequate for manufacturing precast concrete. The main conclusion is that rainwater can be used to manufacture precast concrete in the factory studied herein.

The objective of this study was to develop guidelines for rainwater harvesting system sizing of shopping centres in South Africa. Three generalized dimensionless relationships relating rainwater supply and demand to tank size, yield and reliability were developed based on 101 years long daily time step simulations of rainwater harvesting of 19 shopping centres located in four regions. Daily rainfalls were obtained from nearby rainfall stations and daily non-potable demands were based on the size of the retail area. The simulations revealed within-year storage behaviour with considerable variation of the yield specified as the number of days for which demand was met each year. The Weibull plotting position formula was applied on the time series of yields to obtain yield-reliability relationships. Simulation results of the hydrologically optimum systems were used to develop two of the generalized relationships and an additional one based on the dependence of the slope of the reliability – yield plots on the optimum yield was formulated to enable analysis of hydrologically non-optimal systems. Most of the relationships fitted best to the non-linear power law form with high correlation coefficients averaging 0.92 and ranging from 0.82 to 1.00. The application of the models for tank sizing and assessing system performance is demonstrated.

The greater Wellington region, New Zealand, is highly vulnerable to large earthquakes because it is cut by active faults. Bulk water supply pipelines cross the Wellington Fault at several different locations, and there is considerable concern about severe disruption of the provision of reticulated water supplies to households and businesses in the aftermath of a large earthquake. A number of policy initiatives have been launched encouraging householders to install rainwater tanks to increase post-disaster resilience. However, little attention has been paid to potential health hazards associated with consumption of these supplies. To assess health hazards for householders in emergency situations, six 200-litre emergency water tanks were installed at properties across the Wellington region, with five tanks being allowed to fill with roof-collected rainwater and one tank being filled with municipal tapwater as a control. Such tanks are predominantly set aside for water storage, and once filled, feature limited drawdown and recharge. Sampling from these tanks was carried out fortnightly for one year, and samples analysed for E. coli, pH, conductivity, a range of major and trace elements, and organic compounds, enabling an assessment of the evolution of water chemistry in water storage tanks over time. Key findings were that the overall rate of E.coli detections in the rain-fed tanks was 17.7%, which is low in relation to other studies. We propose that low incidences of E.coli may be due to biocidal effects of high zinc concentrations in tanks, originating from unpainted galvanised steel roof cladding. Lead concentrations were high compared to other studies, with 69% of rain-fed tank samples exceeding the World Health Organisation’s health-based guideline of 0.01 mg/L. Further work is required to determine risks of short-term consumption of this water in emergency situations.

The antioxidant properties and polyphenol content of some selected aromatic plants grown in Greece were studied. Plants were refluxed with 60% methanol after acid hydrolysis. The phenolic substances were quantified by HPLC-DAD. The antioxidant capacity of the extracts was determined with the Rancimat test using sunflower oil as substrate. Free radical scavenging activity was measured using the stable free radical 1, 1-diphenyl-2-picrylhydrazyl (DPPH). Results were compared with standard BHT and ascorbic acid. Total phenol concentration of the extracts was estimated with Folin-Ciocalteu reagent using gallic acid as standard.

The study evaluated potassium peroxymonosulfate (PPMS) efficacy against rifampicin-resistant Salmonella Infantis (rif-SI), Escherichia coli (E. coli), Salmonella Infantis (SI), Newcastle disease virus (NDV) and avian influenza virus (AIV). The assessment encompassed varied concentrations, organic material conditions, and exposure durations to comprehensively evaluate PPMS efficacy. Moreover, PPMS’s efficacy was tested on diverse carrier surfaces and clothing to evaluate its bactericidal and virucidal potential. At the recommended concentrations (1X), PPMS effectively inactivated all pathogens within 5 sec, except for NDV, which required 30 sec in the presence of organic materials. At 0.5X, PPMS successfully inactivated E. coli, AIV and NDV within 5 sec in the absence of organic material. However, rif-SI and SI necessitated 30 sec for inactivation. Most pathogens were inactivated within 30 sec, with the exception for AIV, which was inactivated within 5 sec. PPMS effectively eliminated rif-SI on all carriers within 30 sec. Moreover, at both concentrations, PPMS successfully inactivated AIV on all carriers within 30 sec, except on stainless steel at 0.5X. Furthermore, PPMS at both concentrations required 5 and 30 sec, respectively, to inactivate AIV on the rayon sheet. Therefore, due to its demonstrated efficacy against a wide range of pathogens across diverse surfaces, PPMS emerges as a crucial alternative disinfectant significantly enhancing biosecurity on and around chicken farms. found in and around animal farms, slaughterhouses, and hospitals.

Financial capacity instruments are psychometric tools designed to evaluate individual decisional capacity based on financial decisions. As tests are complex and need special conditions for administration and evaluation, it is difficult to use them in daily geriatric clinics. Our scoping review objective was to evaluate existing financial capacity instruments from the perspective of simplicity and portability. We evaluated one English speaking knowledge database (Medline) using a dedicated MeSH terminology. The review yielded one independent instrument, The Semi-Structured Clinical Interview for Financial Capacity, that can be easy adapted for every-day clinical use. It is simple to understand and perform and do not need trained personnel for administration. It can be finalized in 15 minutes. Initially validated on 261 subjects (with different forms of cognitive impairment), it showed good accuracy and precision mainly in subjects with cognitive impairment. The test is less apt to detect early or fluctuating cognitive impairment. Simplicity, the main advantage of the test, allows gamification fact that increases portability. Familiar images (coins, money) that are used for performing simple tasks does not need complex translation and adaptation. In form of a game, the test is suitable for serial administration, increasing the chance for early capacity reduction detection. Results reflect a physician judgement related to the subjects’ capacity to understand and execute simple financial instructions and not financial proficiency scores. The main limitation of our review is that we investigated only one, English speaking, knowledge database. The scoping strategy generated a financial capacity instrument that can be used in geriatric clinics for early diagnostic of decisional capacity reduction. Further studies are needed to evaluate the reliability and validity of the test in conditions of serial administration and in populations having various financial experience.

Over recent years, the swine industry has witnessed the withdrawal of antibiotics and continuous regulation of zinc and copper oxides in the early-life nutrition of piglets. Due to this development, alternative ingredients or additives from plant sources have been tremendously explored. Therefore, this study's objective was to evaluate the effect of dietary supplementation with tannins on weaned piglets’ growth performance, serum antioxidant capacity, and immune status using a meta-analysis approach. With only the inclusion of non-challenged weaned piglets, a total of 16 studies with parameters of interest were deemed eligible after a two-step screening process following a comprehensive literature search in the scientific databases of Web of Science, Scopus, ScienceDirect, PubMed, and Google Scholar. Two main categories of data, including the study’s characteristics and response variables (growth performance, serum antioxidant, and immune indices), were extracted. Applying the random-effects models, Hedges’ g effect size of supplementation with tannins was calculated using the R software to determine the standardized mean difference (SMD) at a 95% confidence interval. Sub-group analysis and meta-regression further explored heterogeneity (PSMD 0.05, I2 50%, n ≥10). Supplementation with tannin reduced average daily gain (p = 0.20) and feed conversion ratio (p 0.01); however, it increased average daily feed intake (p = 0.07) and final body weight (p 0.01). Meta-regression models indicated that tannin dosage and supplementation duration were directly associated with tannins' effectiveness on productive performance. In the serum, the concentration of glutathione peroxidase, superoxide dismutase, and total antioxidant capacity were elevated (p 0.01) in response to tannins supplementation, while malondialdehydes was reduced (p 0.01). Likewise, decreased immunoglobin A (p = 0.47) and increased immunoglobin M and G levels (p 0.01) were detected. In conclusion, dietary supplementation with tannins, particularly with chestnut and grape seed proanthocyanidins, increases the productivity of weaned piglets. At the same time, it is a possible nutritional strategy to mitigate oxidative stress and stimulate gut health. Thus, supplementing chestnut and grape seed proanthocyanidin tannins in the early phase of swine production could be used to alleviate the incidence of diarrhea.

This study aims to analyse the technical viability and economic feasibility of rainwater harvesting systems for single and multifamily residential buildings in the city of Florianópolis, Brazil. Simulations were conducted for representative buildings in the city under different water usage scenarios and system designs, in a total of 36 simulation scenarios. An economic analysis was performed for four scenarios over a twenty-year period. Both initial and operational costs were considered and net present value, internal rate of return and payback used as feasibility indicators. Almost all of the cases simulated were technically viable for the group of houses, and up to 78.9% for flats. As for the economic analysis, for houses, between 60.1% and 74.8% of the cases were economically feasible, achieving a discounted payback period ranging from 6.2 to 8.6 years. For flats, between 57.8% and 64.2% of the cases were economically feasible, achieving a discounted payback period ranging from 4.8 to 5.6 years. As the water tariff in the city underwent changes recently, the former and current tariff formats were compared. The current tariff format provides more economic benefits for saving potable water, and leads to a higher net present value and a shorter discounted payback period.

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

The availability of current land cover and land use (LCLU) information for monitoring the status of land resources has considerable value in ensuring sustainable land use planning. Similarly, the need to provide updated information on the extent of LCLU change in West Africa has become apparent, given the increasing demand for land resources driven by the rapid population growth in the sub-region. SERVIR West Africa, a regional consortium jointly supported by USAID and NASA to foster the use of geospatial and earth observation data and science for decision-making on critical environmental and food security challenges, in collaboration with the Food and Agriculture Organization of the United Nations (FAO), is building technical capacity in the sub-region to develop and implement harmonized regional land cover classification system for LULC change monitoring in West Africa, based on the Land Cover Meta Language (LCML-ISO 19144-2). This article focuses on the process, potential opportunities, outputs of this collaboration, exemplary use cases, and recommendations for the next steps.

Optical networks, characterized by using optical fibers as a transmission medium, constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is one of the key factors influencing optical network performance, it is important to comprehend its limitations and have the capability to estimate its value. In this context, we revisit the concept of capacity from various perspectives, including channel capacity, link capacity, and network capacity, thus providing an integrated view of the problem. Hence, we review the fundamental concepts behind optical networks, along with the basic physical phenomena present in optical fiber transmission and provide methodologies for estimating the different types of capacities, mainly using simple formulations. In particular, we propose a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with capacitated routing techniques for traffic routing. We apply this method to three reference networks and obtain capacities ranging from tens to hundreds of Terabits/s. Whenever possible, we also compare our results with published experimental data to understand how they relate.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

Motivated by the way animals react in nature, we introduce a fully-connected neural-network model, which incorporates the external pattern presented to the system as a fundamental tool of the recognition process. In this new scenario, in the absence of this external field, memories are not attractors inside basins of attraction, as in usual attractor neural networks, although basins may be created according to the external pattern, thus allowing storing a much larger number of memories. The key point consists in calibrating the influence of the external pattern such as to cancel the noise generated by those memories not correlated with the external pattern.We illustrate how this proposal works by including this new contribution in the standard Hopfield model, showing a significant increase in its recognition capacity (typically by a factor $10^{2}$). As an additional feature of this model, we show its ability to react promptly to changes in the external environment, a crucial attribute of living beings. This procedure can be applied to a wide variety of neural-network models to increase considerably their recognition and reaction capabilities.

Propolis is a bee product widely used as a dietary supplement and included in sweets or baby foods due to its well-known antioxidant and nutritional properties that are directly correlated with its phenolic composition. For this reason, this study analysed the total contents of flavones and flavonols, flavanones and dihydroflavonols, and the antioxidant capacity by using the methods of ABTS and linoleic acid/β-carotene in 99 samples of propolis from Spain and Chile. A rapid method was developed for quantifying these parameters in raw propolis using near infrared (NIR) spectroscopy with an optical fibre probe of remote reflectance applied directly to the ground up sample. The models developed allow the determination of the total of flavones and flavonols (0-183 mg rutin/ g propolis), of the total of flavanones and dihydroflavonols (9-109 mg pinocembrin/ g propolis extract), and the antioxidant capacity by the ABTS method (0-3212 nmolesTrolox/ mg of propolis) and of linoleic acid/β-carotene (22-86% inhibition). The NIR spectroscopy models were applied in external validation to different samples of the calibration group, which led to the conclusion that the methods developed provide significantly identical data to the initial chemical data of reference.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

Quercetin is a flavonoid with a low molecular weight that belongs to the human diet's phenolic phytochemicals and non-energy constituents. Quercetin has a potent antioxidant capacity, being able to capture Reactive Oxygen Species (ROS), reactive nitro-gen species (RNS), and Reactive Chlorine Species (ROC), which act as reducing agents by chelating transition metal ions. Its structure has five functional hydroxyl groups, which work as electron donors and are responsible for capturing free radicals. In addition to its antioxidant capacity, it was described different pharmacological properties of Quercetin, such as carcinostatic properties, antiviral, antihypertensive, anti-inflammatory, protection of Low-Density Lipoprotein (LDL) oxidation, and inhibi-tion of angiogenesis are developed in this review.

This paper has two objectives: the first, to analyze the mediating effect of teacher empowerment between innovation culture and innovation capacity, and between inclusive leadership and innovation capacity; the second, to analyze the moderating effects of the school context on the innovation capacity. Data were collected in a representative sample of secondary schools in Valencia, Spain. The research model adopted is structural equation modeling, using the partial least squares (PLS) technique. The model has confirmed that teacher empowerment mediates between innovation culture and innovation capacity and between inclusive leadership and the innovation capacity. It is found that the educational context does not moderate the relationships in the proposed analysis model. This paper emphasizes the role of teacher empowerment in educational innovation and extends the knowledge of culture and leadership in the school organization.

Microbiome research has gained considerable interest due to the emerging evidence of its impact on human and animal health. Similar to higher organisms, the gut-associated microbiota of mosquitoes affect host fitness and other phenotypes. It is now well established that microbes can alter pathogen transmission in mosquitoes, either positively or negatively, and avenues are being explored to exploit microbes for vector control. However, less attention has been paid to how microbiota affect phenotypes that impact vectorial capacity. Several mosquito and pathogen components, such as vector density, biting rate, survival, vector competence and pathogen extrinsic incubation period all influence pathogen transmission. Interestingly, the mosquito gut-associated microbes can impact each of these components, and therefore ultimately modulate vectorial capacity. Promisingly, this expands the options available to exploit microbes for vector control by also targeting parameters that affect vectorial capacity. However, there are still many knowledge gaps in the biology of the mosquito – microbe symbiosis that need to be addressed in order to understand these interactions more thoroughly and exploit them efficiently. Here, we review current evidence of the impacts of the microbiome on aspects of vectorial capacity highlighting opportunities for novel vector control strategies and areas where further studies are required.

An increasing body of evidence shows that seaweeds, including kelp, can be used as a tool to neutralize or remove excess nutrients and metals from the water column. Here we report on a preliminary field assessment showing potential nutrient and carbon removal differences by sugar kelp and ribbon kelp grown in common gardens. Seawater and tissue samples were collected systematically from two farms in Alaska. Results show differences between % N and % C content between ribbon kelp (Alaria marginata) and sugar kelp (Saccharina latissima). Results also show that tissue nitrogen in ribbon kelp varies sharply due to nitrogen availability in the water column. In contrast, the percentage of tissue N in sugar kelp remains comparatively stable. Our outcomes provide insight into potential differences in nutrient removal and harvest timing for different kelp species.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

The prevention, mitigation and treatment of movement impairments, ideally, requires early diagnosis or identification. As the human movement system has physiological and functional redundancy, movement limitations do not promptly arise at the onset of physical decline. A such, prediction of movement limitations is complex: it is unclear how much decline can be tolerated before movement limitations start. Currently, the term ‘homeostatic reserve’ or ‘physiological reserve’ is used to refer to the redundancy of the human biological system, but these terms do not describe the redundancy in the muscle architecture of the human body. The result of functional redundancy is compensation. Although compensation is an early predictor of movement limitations, clear definitions are lacking and the topic is underexposed in literature. The aim of this article is to provide a definition of compensation and emphasize its importance. Compensation is defined as an alteration in the movement trajectory and/or altering muscle recruitment to complete a movement task. Compensation for capacity is the result of a lack in neuromusculoskeletal reserve, where reserve is defined as the difference between the capacity (physiological abilities of the neuromusculoskeletal system) and the task demand. Compensation for movement objectives is a result of a shift in weighting of movement objectives, reflecting changing priorities. Studying compensation in biomechanics requires altered protocols in experimental set-ups, musculoskeletal models that are not reliant on prescribed movement, and inclusion of alternative movement objectives in optimal control theory.

Africa, home to the world's second-largest population of approximately 1.3 billion, grapples with significant challenges in meeting its medical needs, particularly in accessing quality healthcare services and products. The continent faces a continuous onslaught of emerging infectious diseases, exacerbating the strain on its already fragile public health infrastructure. The emergence of SARS-Cov2 has further exposed the deficiencies in Africa's public health response, ranging from limited diagnostic capabilities to difficulties in vaccine distribution. Compounding these challenges is vaccine hesitancy, which is prevalent in many regions due to varying levels of understanding and trust regarding vaccines. The disparities in vaccine literacy across the continent stem from a complex interplay of factors, including low literacy rates and a history of medical exploitation and misinformation campaigns. These factors have led to a pervasive distrust in medical institutions and healthcare providers among certain African communities. Despite concerted efforts by national governments, private entities, and international partners to address these challenges and improve vaccine literacy, significant hurdles persist. This manuscript examines the current state of education in vaccinology and related sciences in Africa, as well as the continent's efforts to address educational needs in vaccine development and manufacturing. It evaluates initiatives aimed at strengthening vaccine education and literacy, highlighting successful approaches and ongoing challenges. By assessing the progress made and identifying remaining obstacles, this review offers insights into how Africa can enhance its capacity in vaccinology and accelerate its contributions to global health security.

Photodynamic therapy (PDT) has garnered significant attention in the fields of cancer treatment and drug-resistant bacteria eradication due to its non-invasive nature and spatiotemporal controllability. Iridium complexes have captivated researchers owing to their tunable structure, exceptional optical properties, and substantial Stokes displacement. However, most of these complexes suffer from aggregation-induced quenching, leading to diminished luminous efficiency. In contrast to conventional photosensitizers, photosensitizers exhibiting aggregation-induced luminescence (AIE) properties retain the ability to generate a large number of reactive oxygen species when aggregated. To overcome these limitations, we designed and synthesized a novel iridium complex named Ir-TPA in this study. It incorporates quinoline triphenylamine cyclomethylated ligands that confer AIE characteristics for Ir-TPA. We systematically investigated the photophysical properties, AIE behavior, spectral features, and reactive oxygen generation capacity of Ir-TPA. The results demonstrate that Ir-TPA exhibits excellent optical properties with pronounced AIE phenomenon and robust capability for producing singlet oxygen species. This work not only introduces a new class of metal iridium complex photosensitizer with AIE attributes but also holds promise for achieving remarkable photodynamic therapeutic effects in future cellular experiments and biological studies.

eHealth applications are an essential component in achieving Universal Health Coverage. (1) Background: The lack of skilled healthcare personnel has hindered successful integration and use, especially in developing and low and middle-income countries. (2) Methods: A descriptive study was conducted using an online survey to collect quantitative data from 37 organizations to address this issue. (3) Results: The findings showed that there are limited training opportunities available for policymakers and eHealth specialists. Additionally, obstacles such as insufficient funds, inadequate infrastructure, poor leadership, and governance were identified and found to be context specific. To mitigate these challenges, the study proposed continuous in-service training, the implementation of computer-based systems, and the integration of academic modules. The importance of strong eHealth policies and committed leaders was also emphasized. (4) Conclusions: The results of this study support previous research and emphasize the importance of implementing practical and uncomplicated solutions to overcome eHealth barriers to capacity building in low- and middle-income countries. It is essential to recognize that the data collected for this study only pertains to BETTEReHEALTH.

Soy isoflavones are considered important sources of bioactive compounds, but they are poorly absorbable, due to their large hydrophilic structures. Some biotransformation strategies have been used to convert the glycosidic form into aglycones, making them available for absorption. This study evaluated the potential of enzymatic and/or microbial fermentation bioprocesses in soymilk extract before and after gastrointestinal in vitro digestion. Commercial β-glucosidase and mix of commercial probiotics containing Lactobacillus acidophilus, L. casei, Lactococcus lactis, Bifidobacterium bifidum e B. lactis were used to biotransform soymilk extract. Isoflavone profile was quantified by HPLC-DAD, total phenolic content by Folin–Ciocalteu test, and antioxidant capacity by ORAC and FRAP. Soymilk enzymatically treated (ET) followed by microbial fermentation (ET+F) resulted in the conversion of glycosylated isoflavones (6-fold lower than control for daidzin and 2-fold for genistin) to aglycones (18-fold greater than control for dadzein and genistein), besides to increase the total phenolic content (3.48 for control and 4.48 mg/ml ET+F) and to improve antioxidant capacity represented by the ORAC (120 for control and 151 mg/ml ET+F) and by the FRAP (285 for control and 317 µl/ml for ET+F) before in vitro digestion. Further, the digested ET+F samples resulted a higher content of genistein (2-fold higher than control) also an increase in the total phenolic content (2.81 for control and 4.03 mg/ml for ET+F) and antioxidant capacity by ORAC were greater compared to undigested samples. In addition, the microbial fermentation process isolated also resulted in the positive effects, but de combination of ET followed by F presented a synergistic effect, suggesting the greater potential for both bioprocesses to contribute to functional and nutritional properties on fermented soy-based products.

The coal mine underground reservoir is an appropriate solution between coal mining and groundwater resource protection and utilization. By calculating the storage capacity of a groundwater reservoir, the storage coefficient has been proved to be always an empirical value. Based on the mathematical derivation of the vertical fracture area ratio and the horizontal fracture area rate of the collapse zone and the fissure zone in the goaf area of the coal seam, the mathematical models of tem are derived, and the model for calculating the water storage coefficient is derived. The water storage coefficient derived from the theoretical model had more basis and more advanced than the traditional empirical value. By using this method, the practical calculation of No.1 underground reservoir of the DaLliuta Coalmine in Shenhua Shendong, has got a perfect matching with the actual groundwater storage capacity.

Rainwater harvesting could be an optional water source to fulfil the emergency water demand in different setups. The aim was to assess if the rainwater harvesting potential for households and selected institutions were sufficient to satisfy the emergency water demand for the prevention of COVID-19 in Dilla town, Southern, Ethiopia. Rain water harvesting potential for households and selected institutions were quantified using 17 years’ worth of rainfall data from Ethiopian Metrology Agency. With an average annual rainfall of 1464 mm, households with 40 and 100 m2 roof sizes have a potential to harvest between 15.71-31.15 m3 and 41.73-82.73 m3 of water using Maximum Error Estimate. Meanwhile 7.2-39.7 m3 and 19.11-105.35 m3 of water can be harvested from the same roof sizes using Coefficient of Variation for calculation. Considering mean monthly rainfall, the health centres and Dilla University can attain 45.7% and 77% of their emergency water demand, while the rest of the selected institutions in Dilla Town can attain more than 100 % of their demand using only rainwater. Rain water can be an alternative water source for the town in the fight against COVID-19.

Nowadays, there is extensive production and use of plastic materials for different industrial activities. These plastics, either from their primary production sources or through degradation processes of the plastics themselves, can contaminate the ecosystem with micro and nanoplastics. Once in the aquatic environment, these microplastics can be the basis for the adsorption of chemical pollutants, favoring that these chemical pollutants disperse more quickly in the environment and can affect living beings. Due to the lack of information on adsorption, three machine learning models (random forest, support vector machine, and artificial neural network) to predict different microplastic/water partition coefficients (log Kd) were developed using two different approximations (based on the number of input variables). The best-selected machine learning models present, in general, correlation coefficients upper than 0.92 in the query phase, which indicate that these type of models could be used for a rapid estimation of the absorption of organic contaminants on microplastics.

One of the mechanisms used in the management and cure of atherosclerosis is reverse cholesterol transfer (RCT), which plays a vital role in the export of cholesterol from peripheral cells. Cholesterol efflux from macrophages in the subintima of the vessel wall is a critical part of RCT. ATP-binding cassette transporter A1 (ABCA1) and ATP-binding cassette transporter G1 (ABCG1) are involved in the transfer of cholesterol from arterial macrophages to extracellular high-density lipoprotein cholesterol (HDL). The HDL then transports esterified cholesterol to the liver for elimination. An important factor in the reverse cholesterol transport and excretion of extracellular cholesterol is HDL. Atherogenesis can be prevented by altering the processes of RCT and cholesterol efflux, and this might lead to novel treatment options for cardiovascular disease. Research of novel modifying variables for RCT and cholesterol efflux is necessary. A better understanding of RCT's molecular processes has been gained via research, allowing for the creation of new treatments that make use of RCT's potential for pharmacological improvement. The purpose of this review is to provoke discussion on the potential impact of selected flavonoids on cholesterol efflux on the progression of atherosclerosis (Fig. 1.).

A statistical analysis of semantic memory should reflect the complex, multifactorial structure of the relations among its items. Still, a dominant paradigm in the study of semantic memory has been the idea that the mental representation of concepts is structured along a simple branching tree spanned by superordinate and subordinate categories. We propose a generative model of item representation with correlations that overcomes the limitations of a tree structure. The items are generated through "factors" that represent semantic features or real-world attributes. The correlation between items has its source in the extent to which items share such factors and the strength of such factors: if many factors are balanced, correlations are overall low; whereas if a few factors dominate, they become strong. Our model allows for correlations that are neither trivial nor hierarchical, but may reproduce the general spectrum of correlations present in a data-set of nouns. We provide an estimate of the number of concepts that can be stored and retrieved by a large-scale cortical network, the Potts network, which is perhaps approximately 10⁷ with human cortical parameters. When this storage capacity is exceeded, however, retrieval fails completely only for balanced factors; above a critical degree of imbalance, a phase transition leads to a regime where the network still extracts considerable information about the cued item, even if not recovering its detailed representation: partial categorization seems to emerge spontaneously as a consequence of the dominance of particular factors, rather than being imposed ad hoc. We argue this to be a relevant model of semantic memory resilience in Tulving’s remember/know paradigms.

Alum sludge, an inevitable by-product from the water purification process, which had been applied as substrates in some constructed wetlands with good performance, especially for phosphorus (P) adsorption. The raw alum sludge is like clay lump with irregular shape and has a leaching concern used in the water. For a better reuse, herein, sludge was fired to produce alum sludge ceramsite (ASC) with a uniform spherical shape via four-step process of kneading sludge ball, air drying, preheating at 400°C for 10 min and firing at 600℃ for 5 min. Thereafter the physicochemical properties and P adsorption ability of ceramsite were investigated. Through XRD and FT-IR tests, there was no obvious difference between ASC and air-dried alum sludge ball (adASB) on the phase structure, but a certain amount of Al-OH group loss on the surface of ASC. The structure of ASC was still amorphous as same as adASB, while ASC possessed more micropore structure and bigger specific surface area than those of adASB. Adsorption experiments showed the P adsorption behaviors of ASC and adASB were much similar, and their adsorption kinetics all accorded with the two-step adsorption kinetics rate equation and pseudo-second-order kinetics equation. The maximum adsorption capacities of ASC and adASB fitted by Langmuir model were 1.66 mg/g and 1.89 mg/g respectively. It should be pointed that, compared with other adsorbents, ASC produced in this study still had a higher ability to adsorb P. Therefore, ASC should have a great application potential for P removal in the wastewater treatment in China.

There have been relatively few researches that determine the role of bricolage in mediating the empirical relationship between strategic flexibility and product innovation. However, most of the research has studied strategic flexibility to engage the absorptive capacity and facilitate product innovation. The Bricolage approach emphasizes utilizing existing resources in product innovation and explores the mechanisms behind bricolage. A resource-based approach to product innovation involves combining resources in the development process in a concrete manner. This is a groundbreaking study since it is the first to examine empirically how absorptive capacity affects product innovation through bricolage and the serial mediation of strategic flexibility. As a consequence of presenting our results, we concluded that absorptive capacity positively and significantly influences product innovation through the serial mediation of strategic flexibility and bricolage. For strategic flexibility to play a role in supporting product innovation, bricolage is one of the mechanisms that can be utilized. This study contributes to the literature on strategic flexibility by examining the effect of strategic flexibility on bricolage and product innovation from the standpoint that absorptive capacity enhances the strategic flexibility of high-tech SMEs in China. Furthermore, this research offers new insights into the relationship between absorptive capacity and product innovation. In addition, it also provides insight into the economic opportunities that may result from product innovation in transition economies such as China.

The intensive care units in North West London are part of one of the oldest critical carenetworks in the UK, forming a mature and established strategic alliance to shareresources, experience and knowledge for the benefit of its patients. North WestLondon saw an early surge in COVID-19 admissions, which urgently threatened thecapacity of some of its intensive care units even before the UK government announcedlockdown. The pre-existing relationships and culture within the network allowed itsmembers to unite and work rapidly to develop agile and innovative solutions, protectingany individual unit from becoming overwhelmed, and ultimately protecting its patients.Within a short 50-day period 223 patients were transferred within the network todistribute pressures. This unprecedented number of critical care transfers, combinedwith the creation of extra capacity and new pathways, allowed the region to continue tooffer timely and unrationed access to critical care for all patients who would benefitfrom admission. This extraordinary response is a testament to the power and benefitsof a regionally networked approach to critical care, and the lessons learned maybenefit other healthcare providers, managers and policy makers, especially in regionscurrently facing new outbreaks of COVID-19.

The concept of friction damper is widespread technique and used to reduce the structural vibrations in many industrial applications. These friction dampers are generally coated with low wear rate materials to reduce the fretting wear. This paper investigates the use of physical vapor deposition (PVD) nitride based AlTiN coating material applied over the stainless steel friction damper to enhance the damping capacity and to reduce the fretting wear. A friction test rig has been developed to measure the dynamic hysteresis characteristics of friction damper at high temperature (700 °C). The damping capacity and fretting wear analysis is carried out at room temperature, 300 °C and 600 °C. The force versus displacment characterisitcs curve is used to predict the damping capacity and fretting wear analysis is carried out at microscopic level for the comparision. It is observed that at room temperature AlTiN coated friction damper has not much influence to improve the damping capacity and to reduce the fretting-wear. However, at high temperature it has better damping capacity and less wear in comparision to uncoated friction damper. Wear behaviour in coated and uncoated damper is different at room temperature and at elevated temperature.

We study the short−term memory capacity of ancient readers of the original New Testament written in Greek, of its translations to Latin and modern languages. To model the short–term capacity, we have considered the number of words per interpunctions, the “word interval” , because this parameter can model how the human mind memorizes “chunks” of information. Since can be calculated for any alphabetical text, we can perform experiments − otherwise impossible − with ancient readers by studying the literary works they used to read. The “experiments” compare the of texts of a language/translation to those of another language/translation by measuring the minimum average probability of finding joint readers (those who can read both texts because of their similar short–-term memory capacity) and by defining an “overlap index”. We also define a population of universal readers who can read any the New Testament written in alphabetical language. More than 50% of the readers of specific languages overlap with the universal readers with probability . Future work is vast, with many research tracks, because alphabetical literatures are very large and allow many experiments, such as comparing authors, translations or even texts written by artificial intelligence tools.

China is a large agricultural country that produces a large amount of crop straw every year. Thus, the development of cost-effective and economic application of invasive plants is warranted. Biochars derived from crop straw has been proven to be promising for adsorbent materials. However, less studies have focused on biochar derived from different types of crop straw as adsorbent under the same conditions to compare their adsorption performance. Here, we characterized the five biochars in the same system (600 ℃). In results, GBC has higher ash content, pH, CEC, specific surface area, mineral composition and oxygen-containing functional groups. The adsorption kinetics can be explained adequately by pseudo-second-order model and Langmuir model, indicating that the adsorption behavior of the biochar is both physical adsorption and chemical adsorption, the adsorption process includes complexation reaction, cationic π bond, ion precipitation and electrostatic adsorption. In conclusion, GBC exhibited higher metal equilibrium adsorption capacities (125 mg·g-1 for Pb2+, 29 mg·g-1 for Cd2+). The solution pH, biochar dosing, pyrolysis temperature and the properties of these heavy metals were responsible for adsorption capacity, thus showing stronger affinity and better adsorption effect. Our results are important for the selection and utilization of plant-based biochar for different heavy metals.

(1) Background: The purpose of this study was therefore to analyze the predictive capacity of the three variables (impulsivity, sensation-seeking and drug use) in aggressors and victims of violence. (2) Methods: The design is cross-sectional quasi-experimental. A sample of 822 students aged 13 to 18 who had filled in an ad hoc questionnaire, the State Impulsivity Scale and the Sensation-Seeking Scale, was used for this. (3) Results: The results show that aggressors had high levels of gratification, automatism, attentional factor, disinhibition and susceptibility to boredom, and use alcohol and/or tobacco. The variables that could predict involvement as an aggressor in peer conflict are use of alcohol, smoking, high levels of gratification, automatism and attentional factors and a high degree of disinhibition and susceptibility to boredom. The disinhibition is the best predictor of aggressor. (4) Conclusions: Thus having available empirical evidence that facilitates detection of predictive variables for participation in violence is going to favor the design of effective education intervention for reducing risk behavior.

As the most important component of soft robot, the pneumatic actuator can drive robot movement. However, the effect of the actuator pneumatic network geometry on the actuator load capacity is insufficient. In this paper, the finite element analysis method is applied to calculate the load force and stability torque of the pneumatic actuator under a wide range of length and height dimensions of the pneumatic network. The effect of the network size on the structure rigidity, load capacity and deformation of the actuator is analyzed. Based on the calculation results, the effect of network structure size on the deformation and load capacity is analyzed, and the optimal geometric results with the maximum load capacity are obtained. This study provides theoretical guidance for the structural design and optimization of the pneumatic actuator.

Myalgic Encephalomyelitis / Chronic Fatigue Syndrome (ME/CFS) is an acquired disease with significant morbidity that affects both children and adults. Effective tools to assess functional capacity (FC) are severely lacking which has significant consequences for timely diagnosis, assessments for patient disability benefits and assessing the impact and effectiveness of interventions. In interventional research the inability to assess FC can result in an incomplete assessment of the potential effect of the intervention. Specifically of concern is that if an intervention is effective in reducing symptom load, patients may increase their activity level to reach a pre-intervention symptom load. Thus, if FC is not accurately assessed, beneficial treatment outcomes may be missed. To address this issue, using extensive, repeated patient feedback we have developed a new questionnaire, FUNCAP, to achieve optimal FC assessment in ME/CFS patients. The questionnaire covers eight domains and activity types: A. Personal hygiene / basic functions, B. Walking / movement, C. Being upright, D. Activities in the home, E. Communication, F. Activities outside the home, G. Reactions to light and sound, and H. Concentration. Through five rounds of anonymous web-based surveys and a further test - retest validation round, two versions of the questionnaire were developed; a longer version comprising 55 questions (FUNCAP55) to improve diagnostic and disability benefit/ insurance FC assessments and a shorter version (FUNCAP27) for interventional research and less extensive FC assessments. FUNCAP may also be useful in other conditions where fatigue and PEM is present, such as Long Covid.

This study aimed to evaluate the capacity of Saccharomyces cerevisiae for Cadmium absorption in Milk. Nowadays one of the most serious problems is heavy metals pollution. Applying microorgaisms as a novel biotechnology is so useful especially in foodstuffs. Among the biosorbents for heavy metals’ removal, Saccharomyces cerevisiae has got an increasing attention due to its popularity in food industry. In this regard, the effects of some important factors such as the initial metal concentration, biomass concentration and contact time on the biosorption capacity of Saccharomyces cerevisiae were studied. The biosorption was analyzed by the inductively coupled plasma mass spectrometer (ICP-MS). The maximum Cd bioremoval (70%) was at 80 μg/L of this metal concentration in milk samples containing 30×10⁸ CFU Saccharomyces cerevisiae at the end of storage time (the 4^th day). There were no significant differences in sensory and physicochemical properties of milk samples during storage (p < 0.05). The isotherm studies followed by two popular models; Langmuir and Freundlich and the results showed a better fit to the Langmuir isotherm. All together, the results of this project demonstrated that the approach of using this valuable yeast, could be applied for food and drinks’ detoxification and producing healthier foods.

The most common index for representing structural condition of the pavement is the structural number. The current procedure for determining structural numbers involves utilizing falling weight deflectometer and ground-penetrating radar tests, recording pavement surface deflections, and analyzing recorded deflections by back-calculation manners. This procedure has two drawbacks: 1. falling weight deflectometer and ground-penetrating radar are expensive tests, 2. back-calculation ways has some inherent shortcomings compared to exact methods as they adopt a trial and error approach. In this study, three machine learning methods entitled Gaussian process regression, m5p model tree, and random forest used for the prediction of structural numbers in flexible pavements. Dataset of this paper is related to 759 flexible pavement sections at Semnan and Khuzestan provinces in Iran and includes “structural number” as output and “surface deflections and surface temperature” as inputs. The accuracy of results was examined based on three criteria of R, MAE, and RMSE. Among the methods employed in this paper, random forest is the most accurate as it yields the best values for above criteria (R=0.841, MAE=0.592, and RMSE=0.760). The proposed method does not require to use ground penetrating radar test, which in turn reduce costs and work difficulty. Using machine learning methods instead of back-calculation improves the calculation process quality and accuracy.

Worldwide the steel corrosion is one of the greatest deterioration problems for reinforced concrete structures. Comparing some literature experimental results with a complex FEM model, the present paper points out the principal aspects those characterize the static behavior of RC elements damaged by corrosion. Moreover, the non-dimensional abaci defined for some specific case studies finalized to the evaluation of the residual flexural strength of corroded elements highlight the dangerousness of the corrosion degradation if the failure of the element is governed by the steel

This study aims to improve the shaft with hexagon joints to be a type not requiring welding or bolts in the static load test . In order to evaluate the bearing capacity of helical piles, two sites were selected to conduct pile installation for the field test and the pile load test. For the pile load test, the static pile load test and the dynamic pile load test were carried out, and torque was measured during pile installation for the field test to compare and analyze expected bearing capacity and thus assess the feasibility of the method for estimating the bearing capacity. The field pile load test revealed the bearing capacity of the gravity grout pile was the same or greater than 600kN in the static pile load test in accordance with AC 358 Code. The non-grout pile showed the bearing capacity the same or smaller than 600kN, suggesting gravity grouting is required. Moreover, the field pile load test was used to establish the bearing capacity equation considering the torque in pile installation, and a small number of samples were used to establish the equation which can be used as a basic data.

Highly weathered soils in the tropics are low in fertility, negatively affecting plant growth. The potential of biochar for improving soil nutrient retention is reportedly promising, triggering this study to assess the nutrient retention capacities of two biochars when applied at 2% in combination with two composts also applied at 2% to an Ultisol (Ustic Kanhaplohumult, Leilehua series) and an Oxisol (Rhodic haplustox, Wahiawa series) of Hawai’i. Chinese cabbage (Brassica rapa cv. Bonsai) was used as the test plant in two greenhouse plantings, which had a factorial completely randomized design with three replicates per treatment. The results indicated that the combined additions of biochar and compost significantly increased the pH, EC, P and K of the soils; improved Ca, Mg and Fe uptake; and increased shoot and total cabbage fresh and dry matter. Exchangeable aluminum in the Ultisol was decreased from 2.5 cmol+/kg to virtually zero. Extractable Mn and Fe in the high Mn-Oxisol were decreased by 55 and 42%, respectively. Chinese cabbage growth in the Ultisol amended with the lac tree (Schleichera oleosa) wood biochar and vermicompost was almost twice over lime at 2 cmol+/kg. Essential nutrients in the plant tissues, with the exception of N and K, were sufficient for the cabbage growth, suggesting increases in nutrients and reduced soil acidity by the additions of biochar combined with compost were the probable cause.

Heterogeneous systems of limited capacity have general applications in manufacturing, but also for logistic or service systems, due to the differences in server or workstation performance or work assignment, in close relationship with system flexibility, where saturation and blocking are ordinary situations of systems with high demand and limited capacity, so accurate loss quantification is essential for performance evaluation. Multi-class systems of limited capacity have been studied much less than parallel homogeneous systems (Erlang models). In this context, accurate models for parallel heterogeneous ordered-entry systems are developed: without any prior queue, M/Mi/c/c, and with a k capacity queue M/Mi/c/c+k. These new matrix models give an exact state formulation, and their accuracy is verified through discrete event simulation and comparison with literature results. Also, the effect of queue capacity is studied in relationship with the pattern of service rates. Next, the heterogeneous recirculating system model is also developed with good approximation results. Finally, the proposed models are applied to evaluate systems with non-exponential service times, through a new hybrid methodology by combining the Markovian model and the Monte Carlo Method (MCM) for normal or lognormal service times that also yield useful good approximations to the simulated system.

Lithium-ion batteries are key elements in the development of electrical energy storage solutions. However, due to cycling, environmental and operating conditions, battery capacity tends to degrade over time. Capacity fade is a common indicator of battery state of health (SOH) because it is an indication of how capacity has been degraded. However, battery capacity cannot be measured directly, so there is an urgent need to develop methods for estimating battery capacity in real time. By analyzing the historical data of a battery in detail, it is possible to predict the future state of the battery and forecast its remaining useful life. This paper develops a real-time, simple and fast method to estimate the cycle capacity of a battery during the charge cycle using only data from a short period of each charge cycle. This proposal is attractive because it does not require data from the entire charge period, since batteries are rarely charged from zero to full. The proposed method allows simultaneous and accurate real-time prediction of the health and remaining useful life of the battery over its lifetime. The accuracy of the proposed method has been tested using experimental data from several lithium-ion batteries with different cathode chemistries under various test conditions.

There is an increasing interest in revisiting plants for drug discovery proving scientifically their role as remedies. Pistacia lentiscus (PL) is a wild-growing shrub rich in terpenoids, which are pharmacological appealing. The more recurrent components in the oil are represented by α-pinene, terpinene, caryophyllene, limonene, and myrcene. High concentration of polyphenols enriches the extracts. PL-extracts showed in vitro and in animal model strong anti-inflammatory and anti-oxidative activities. The anti-inflammatory activity mainly occurs due to inhibition of NF-kB pathway or directly toward the proinflammatory cytokines, or arachidonic acid cascade against COX-2 and LOX. The antimicrobial activity of PL essential oil and extracts includes among others Staphylococcus aureus, Escherichia coli, periodontal bacteria and Candida sp.. In conclusion, the biological properties, and particularly the anti-inflammatory and anti-microbial capacity, propose PL as a new safe pharmaceutical agent.

We report the development of in vitro propagation protocols through adventitious shoot induction pathway for a rare and medicinal Scutellaria havanensis. In vitro propagation studies using nodal explants showed MS medium supplemented with 10µM 6-Benzylaminopurine induced highest number of adventitious shoots in a time dependent manner. A ten - day incubation was optimum for shoot bud induction as longer exposures resulted in hyperhydricity of the explants and shoots induced. We also report preliminary evidence of Agrobacterium tumefaciens EHA105 - mediated gene transfer transiently expressing of green fluorescent protein in this species. Transformation studies exhibited amenability of various explant tissues, internode being the most receptive. As the plant has medicinal value, research was carried out to evaluate its potential antioxidant capacity and the efficacy of methanolic leaf extracts in curbing the viability of human colorectal cancer cell line HCT116. Comparative total polyphenol, and flavonoid content measurement of fresh and air dried leaf extract revealed that the fresh leaf extracts contain higher total polyphenol and flavonoid content. The HCT 116 cell viability assessed by colorimetric assay using a 3-(4, 5-dimethyl-thiazol-2-yl)-2, 5-diphenyltetrazolium bromide, showed a steady growth inhibition after 24 hours of incubation. Scanning Electron Microscopy of leaf surface revealed high density of glandular and non-glandular trichomes. This research provides basis for the conservation of this rare plant and future phytochemical screening and clinical research.

Roundabouts need capacity and safety improvements compatible with manual-driven, not only with autonomous vehicles. The signaling and control of roundabouts must evolve and incorporate current technologies. For that, we approach roundabouts as synchronous switches of vehicles. This paper describes Synchronous Roundabouts with Rotating Priorities, a roundabout control system based on vehicle platoons arriving at the roundabout at speed identical to the roundabout and within the time slot assigned to their entry, avoiding conflicts and stops, thus increasing roundabout capacity and safety. Signaling is visual for human drivers and also wireless for connected and autonomous vehicles. We evaluate analytically and with simulations roundabouts of different radius for several values of the average distance between vehicles. Average delays are 28,7 % lower, with negligible dispersion. The capacity improvements depend on design parameters: in our set is moderate for small roundabouts but goes up to 70-100 % for short distances and medium and large roundabouts.

This paper focuses on robust multi-criteria traffic network equilibrium problems with path capacity constraints. The concepts of robust vector equilibrium and robust vector equilibrium with respect to worst case are introduced, respectively. To generate a subset of robust vector equilibrium, an equivalent min-max optimization problem is constructed. In addition, a direct search algorithm, in which the step size without derivatives and redundant parameters, for solving this min-max problem is proposed. To find a subset of robust vector equilibrium with respect to worst case, an equivalent smoothing optimization problem based on a variant version of ReLU activation function is established. Numerical experiments are also presented to expound the advantages of the algorithms.

For a wide industrial application of magnesium alloys, a method for imparting high damping properties while maintaining mechanical properties is required. Controlling the crystallographic texture seems to be useful, because dislocations are known to have a significant influence on the damping characteristics of magnesium alloys. Therefore, the effect of twinning and annealing, which can affect to the recrystallization were investigated in this study. An AZ31 alloy was hot rolled at 673K with a reduction ratio of 10 % and 50 %, and then annealed at 673K and 723K for 0.5, 1, 2, and 3H respectively. SEM-EBSD was used to examine the microstructure and texture. In addition, each specimen’s hardness and internal friction were contemporarily measured. As a result, hot rolling produced tensile twins and their fraction increased with internal friction when the reduction ratio increased. Due to annealing, a discontinuous type of static recrystallization occurred within the twinning grains, and was highly activated along with the increasing annealing temperature and the fraction of twinning. In the samples annealed at 723K, the internal friction continuously increased over the annealing time, whereas in the samples annealed at 673K, the decrease in dislocation density was delayed while, the internal friction showed a relatively low value.

The response of carbon fixation in C3 plants to elevated CO2 is relatively larger when photosynthesis is limited by carboxylation capacity (VC) than when limited by electron transport (J). Recent experiments under controlled, steady-state conditions have shown that photosynthesis at elevated CO2 may be limited by VC even at limiting PPFD. These experiments were designed to test whether this also occurs in dynamic field environments. Leaf gas exchange was recorded every 5 minutes using two identical instruments both attached to the same leaf. The CO2 concentration in one instrument was controlled at 400 mol mol-1 and one at 600 mol mol-1. Leaves were exposed to ambient sunlight outdoors, and cuvette air temperatures tracked ambient outside air temperature. The water content of air in the leaf cuvettes was kept close to that of the ambient air. These measurements were conducted on multiple, mostly clear days for each of three species, Glycine max, Lablab purpureus, and Hemerocallis fulva. The results indicated that in all species, photosynthesis was limited by VC rather than J at both ambient and elevated CO2 both at high midday PPFDs and also at limiting PPFDs in the early morning and late afternoon. During brief reductions in PPFD due to midday clouds, photosynthesis became limited by J, The net result of the apparent deactivation of Rubisco at low PPFD was that the relative stimulation of diurnal carbon fixation at elevated CO2 was larger than would be predicted when assuming limitation of photosynthesis by J at low PPFD.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

Capacity Expansion Models (CEMs) are optimization models used for long-term energy planning on national to continental scale. They are typically computationally demanding, thus in need of simplification, where one such simplification is to reduce the temporal representation. This paper investigates how using representative periods to reduce the temporal representation in CEMs distorts results compared to a benchmark model of a full chronological year. The test model is a generic CEM applied to Europe, equipped with a novel formulation for storage in model versions with reduced temporal representation. We test the performance of reduced models at penetration levels of wind and solar of 90%. Three measures for accuracy are used: (i) system cost, (ii) total capacity mix and (iii) regional capacity. We find that: (i) the system cost is well represented (~5% deviation from benchmark) with as few as ten representative days, (ii) the capacity mix is in general fairly well (~20% deviation) represented with 50 or more representative days, and (iii) the regional capacity mix displays large deviations (>50%) from benchmark for as many as 250 representative days. We conclude that modelers should be aware of the error margins when presenting results on these three aspects.

As on 31.03.2020, 55.4 % (205135 MW) of total installed capacity (370106 MW) in India is through coal and lignite based power plants. These plants, set up by central, state and private utilities with substantial capital investment are facing consistently reducing Plant Utilization Factor (known as Plant Load Factor, PLF, in India). In the year 2019-20 the national average thermal power PLF stood at 55.4%, down from 78.6 % in 2007-08. On the other hand, the electricity demand is consistently rising in the country and there exists a peak and energy shortage at national level. In 2019-20 energy shortage was 0.7 % and peak shortage was 0.5 %. A disturbing paradox therefore exists here. On one hand, the country is power deficit, and on the other hand, a large amount of coal based affordable power, ready to be generated by thermal power generators, remains grossly unused. Looking into the fact that considerable investment has gone into developing these thermal power generation assets in the country, the falling PLF is a matter of concern for all the key stakeholders including the power producers, lenders, regulators and consumers. This paper identifies seven major factors that are affecting PLF of thermal power plants and then makes an attempt to project future scenario of PLF so that critical stakeholders can intervene through appropriate actions. Primary research with responses from power professionals has been used to find out the major factors. Future projection of PLF has been done using Partial Least Square (PLS) regression. Projection shows that in the Business As Usual case (Factors increasing at the current CAGR rate), the thermal power plants will face very low level of PLF (14.76 %) by 2024-25. This will mean that many plants will be shut down and many will run for only few hours in a day that too at very low loads. If the future generation mix is kept as indicated by Central Electricity Authority (CEA), a Govt. of India in its report (Draft report on optimal generation capacity mix for 2029-30- CEA- Govt of India) then the thermal power plant average PLF can sustain above 68 % until 2024-25. If followed, this path can be a breather for the thermal power plants.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

Analytical channel design tools have not advanced appreciably in the last decades, and continue to produce designs based upon a single representative discharge that may not lead to overall sediment continuity. It is beneficial for designers to know when a simplified design may be problematic and to efficiently produce alternative designs that approximate sediment balance over the entire flow regime. The Capacity/Supply Ratio (CSR) approach, an extension of the Copeland method of analytical channel design for sand channels, balances the sediment transport capacity of a design reach with the sediment supply of a stable upstream reach over the entire flow duration curve (FDC) rather than just a single discharge. Although CSR has a stronger physical basis than previous analytical channel design approaches, it has not been adopted in practice because it can be a cumbersome and time-consuming iterative analysis without the use of software. We investigate eighteen sand-bed rivers in a comparison of designs based on the CSR approach and five single-discharge metrics: the effective discharge (Qeff), the 1.5-year recurrence interval discharge (Q1.5), the bankfull discharge (Qbf), and the discharges associated with 50th (Qs50) and 75th (Qs75) percentiles of the cumulative sediment yield curve. To facilitate this analysis we developed a novel design tool using the Visual Basic for Applications (VBA) programming language in Excel® to produce stable channel slope-width combinations based on the CSR methodology for both sand- and gravel-bed streams. The CSR Stable Channel Design Tool’s (CSR Tool) code structure was based on Copeland’s method in SAM and HEC-RAS (Hydrologic Engineering Center’s River Analysis System) and was tested with a single discharge to verify outputs. The Qs50 and Qs75 single-discharge designs match the CSR output most closely, followed by the Qbf, Qeff, and Q1.5. The Qeff proved to be the most inconsistent design metric because it can be highly dependent on the binning procedure used in the effectiveness analysis. Furthermore, we found that the more rigorous physical basis of the CSR analysis is potentially most important in designing ‘labile’ channels with highly erodible substrate, high perennial flow ‘flashiness,’ low width-to-depth ratio, and high incoming sediment load. The CSR Tool provides a resource for river restoration practitioners to efficiently utilize in-depth design techniques that can promote sediment balance in dynamic fluvial systems.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

Digital transformation provides new drivers for economic performance growth in enterprises, but can it further improve ESG performance and support sustainable development? Based on the perspective of resources and capabilities, this paper uses the relevant data of 1588 listed companies in strategic emerging industries from 2011 to 2021 to study the differential impact of digital transformation on enterprise ESG performance, and further tests the mediating role of absorptive capacity and the moderating role of regional digital level. The research results indicate that: firstly, digital transformation of enterprises can positively promote the improvement of ESG performance; Secondly, there are significant differences in the impact of digital transformation on the ESG performance of enterprises in terms of property rights and industry characteristics. The ESG performance of state-owned enterprises and high-end equipment manufacturing enterprises is more sensitive to digital transformation; Thirdly, absorptive capacity plays a mediating role between digital transformation and corporate ESG performance; Fourthly, the positive regulation of regional digital level promotes the ESG performance of enterprises through digital transformation. The research conclusion is based on a digital perspective, providing relevant insights for improving the ESG performance of strategic emerging industry enterprises and expanding their ESG development paths.

Individuals diagnosed with systemic arterial hypertension (SAH) are considered risk groups for COVID-19 severity. This study assessed differences in cardiac autonomic function (CAF) and functional capacity (CF) in SAH individuals without COVID-19 infection compared to SAH individuals post-COVID-19. Participants comprised 40 SAH individuals aged 31 to 80 years old, grouped as SAH with COVID-19 (G1; n=21) and SAH without COVID-19 (G2; n=19). CAF was assessed via heart rate variability (HRV), measuring R-R intervals during a 10-minute supine period. Four HRV indices were analyzed through symbolic analysis: 0V%, 1V%, 2LV%, and 2UV%. FC assessment was performed by a 6-minute walk test (6MWT). G1 and G2 showed no difference between significant age, anthropometric, clinical and medication. G2 exhibited superior 6MWT performance, covering more distance (522±78 vs. 465±59 meters, p&lt;0.05). Specifically, G2 demonstrated a moderate, positive correlation between 6MWT and the 2LV% index (r=0.58; p&lt;0.05). Shorter walking distances were observed during 6MWT in SAH individuals post-COVID-19. However, the study did not find impaired cardiac autonomic function in SAH individuals post-COVID-19 compared to those without. This suggests that while COVID-19 impacted FC, CAF remained relatively stable in this population.

We propose a model for medium-term hydropower scheduling (MTHS) with variable head and uncertainty in inflow, reserve capacity, and energy price. With an increase of intermittent energy sources in the generation mix, it is expected that a flexible hydropower producer can obtain added profits by participating in other markets than just the energy market. To capture this added potential the hydropower system should be modeled with a higher level of details. In this context, we apply an algorithm based on stochastic dual dynamic programming (SDDP) to solve the nonconvex MTHS problem, and show that the use of Strengthened Benders (SB) cuts to represent the expected future profit (EFP) function provide accurate scheduling results for slightly nonconvex problems. A method to visualize the EFP function in a dynamic programming setting is provided, serving as a useful tool for a priori inspection of the EFP shape and its nonconvexity.

Increased nutrient withdrawal by rapidly expanding intensive cropping systems, in combination with imbalanced fertilization, is leading to potassium (K) depletion from agricultural soils in Asia. There is an urgent need to better understand the soil K-supplying capacity and K-use efficiency of crops to address this issue. Maize is increasingly being grown in rice-based systems in South Asia, particularly in Bangladesh and North East India. The high nutrient extraction, especially K, however, causes concerns for the sustainability of maize production systems in the region. The present study was designed to estimate, through a plant-based method, the magnitude, and variation in K-supplying capacity of a range of soils from the maize-growing areas and the K-use efficiency of maize in Bangladesh. Eighteen diverse soils were collected from several upazillas (or sub-districts) under 11 agro-ecological zones to examine their K-supplying capacity from the soil reserves and from K fertilization (@ 100 mg K kg-1 soil) for successive seven maize crops grown up to V10-V12 in pots inside a net house. A validation field experiment was conducted with five levels of K (0, 40, 80, 120 and 160 kg ha-1) and two fertilizer recommendations based on “Nutrient Expert for Maize-NEM” and “Maize Crop Manager-MCM” decision support tools (DSSs) in 12 farmers’ fields in Rangpur, Rajshahi and Comilla districts in Bangladesh. Grain yield and yield attributes of maize responded significantly (P < 0.001) to K fertilizer, with grain yield increase from 18 to 79% over control in all locations. Total K uptake by plants not receiving K fertilizer, considered as potential K-supplying capacity of the soil in the pot experiment, followed the order: Modhukhali >Mithapukur >Rangpur Sadar >Dinajpur Sadar >Jhinaidah Sadar >Gangachara >Binerpota >Tarash >Gopalpur >Daudkandi >Paba >Modhupur >Nawabganj Sadar >Shibganj >Birganj >Godagari >Barura >Durgapur. Likewise in the validation field experiment, the K-supplying capacity of soils was 83.5, 60.5 and 57.2 kg ha-1 in Rangpur, Rajshahi, and Comilla, respectively. Further, the order of K-supplying capacity for three sites was similar to the results from pot study confirming the applicability of results to other soils and maize-growing areas in Bangladesh and similar soils and areas across South Asia. Based on the results from pot and field experiments, we conclude that the site-specific K management using the fertilizer DSSs can be the better and more efficient K management strategy for maize.

Sea level rise and increased storm events, urge cities to develop governance capacity. However, a cohesive conceptual and empirical-based understanding of what governance capacity implies, how to measure it, and what cities can learn, is largely lacking. Understanding the influence of context is critical to address this issue. Accordingly, we aim to identify crosscutting contextual factors and their influence in impeding, enhancing or prioritising different elements of governance capacity to address urban flood risk. By assessing governance capacity through nine conditions and 27 indicators in two Dutch and two cities in the UK, three crosscutting contextual factors are identified: 1) flood probability and impact, 2) national imposed institutional setting, and 3) level of authority to secure long-term financial support. We found that contextual factors explain differences in urban capacity-priorities within and between both countries. The institutional setting in the UK and recent political devolution emphasized the role of citizen awareness, stakeholder engagement, entrepreneurial agents, and the overall necessity for local capacity-development. The Dutch focus on flood safety through centralised public coordination reduces flood probability but also inhibits incentives to reduce flood impacts and reduced public awareness. In conclusion, the three identified contextual factors enable a better understanding of capacity-building priorities.

Accurate estimation of livestock carrying capacity (LCC) and implementing an appropriate actual stocking rate (ASR) is key to sustainable management of grazing adapted alpine grassland ecosystems. Reliable determination of aboveground biomass is fundamental to these determinations. Peak aboveground biomass (AGBP) captured from satellite data at the peak of the growing season (POS) is widely used as a proxy for annual aboveground biomass (AGBA) to estimate LCC of grasslands. Here we demonstrate limitations of this approach and highlight the ability of POS in the estimation of ASR. We develop and trail new approaches that incorporate remote sensing phenology timings of grassland response to grazing activity, considering relations between biomass growth and consumption dynamics, in efforts to support more accurate and reliable estimation of LCC and ASR. Results show that based on averaged values from large-scale studies of alpine grassland on the Qinghai-Tibet Plateau (QTP), differences between AGBP and AGBA underestimate LCC by about 31%. Findings from a smaller-scale study that incorporate phenology timings into estimation of annual aboveground biomass reveal that Haibei alpine meadows were overgrazed by 11.5% during the study period from 2000-2005. The methods proposed can be extended to map grassland grazing pressure by predicting LCC and tracking ASR, thereby improving sustainable resource use in alpine grasslands.

Tracked vehicles play a vital role in accessing challenging terrains, offering stability, traction, and versatility for various applications, including deep-sea exploration. However, the seafloor and sediment contain valuable but poorly understood resources, making it a significant challenge for tracked vehicles during exploration. Consequently, it is imperative to conduct comprehensive studies before considering these terrains for off-road purposes. In this study, we developed a rigid, flexible track vehicle equipped with various sensors, focusing on monitoring pressure sinkage. Cohesive soils like Bentonite and Diatom soil, particularly when combined with sand and gravel mixtures, were used for the investigation and assessed for ground pressure, bearing capacity, and sinkage in rigid-flexible tracked vehicles on these characterized terrains under varying moisture conditions. Our findings indicated that increased moisture content in bentonite soil resulted in significantly higher track slippage and sinkage compared to diatomaceous earth soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics compared to bentonite soil. These significant variations between these two soil types under changing moisture conditions highlight the complexity of such terrains. Therefore, understanding the soil and its physical properties is crucial before applying them to natural terrains. Furthermore, this study emphasizes the importance of precision in assessing the physical properties of natural terrains for the development of tracked vehicles for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

Transcatheter aortic valve replacement (TAVI) improves event-free survival in patients with severe aortic stenosis, but patients’ exercise capacity remains poor after the procedure. Therefore, we sought to compare the effects of supervised centre-based exercise training program and unsupervised exercise routine on exercise capacity and vascular function in patients after TAVI. Patients were randomised to either centre-based exercise training (12-24 sessions of combined aerobic and low-weight resistance training twice weekly for 8-12 weeks) or unsupervised home-based exercise routine (initial appraisal with detailed recommendations and monthly follow-up). Exercise capacity (cardiopulmonary testing) and vascular function (ultrasonographic measurement of flow-mediated vasodilation [FMD] and arterial stiffness) were assessed at baseline and after the study period. We included 23 patients (mean age 81 years, 61% women), with higher-than-expected drop-out rates (41%) because of the coronavirus-19 pandemic outbreak. Exercise capacity improved over time, irrespective of intervention group: 0.09 ml/min/kg increase in peak oxygen uptake (95%CI [0.01-0.16]; p=0.02), 8.2 Watts increase in workload (95%CI [0.6-15.8]; p=0.034), and 47 seconds increase in cumulative exercise time (95% CI [5.0-89.6]; p=0.029). A between-group difference in change over time (treatment effect) was detected only for FMD (4.49%; 95% CI [2.35; 6.63], p &lt; 0.001), but not for other outcome variables. Both supervised and unsupervised exercise training improve exercise capacity and vascular function in patients after TAVI, with supervised exercise training possibly yielding larger improvements in vascular function, as determined by FMD.

Large animal experiments are important for preclinical studies of regenerative stem cell transplantation therapy. Therefore, we investigated the differentiation capacity of pig skeletal muscle-derived stem cells (Sk-MSCs) as an intermediate model between mice and humans for nerve muscle regenerative therapy. Enzymatically extracted cells were obtained from green-fluorescence transgenic micro-mini pigs (GFP-Tg MMP) and sorted as CD34+/45- (Sk-34) and CD34-/45-/29+ (Sk-DN) fractions. The ability to differentiate into skeletal muscle, peripheral nerve, and vascular cell lineages was examined by in vitro cell culture and in vivo cell transplantation into the damaged tibialis anterior muscle and sciatic nerves of nude mice and rats. Protein and mRNA levels were analyzed using RT-PCR, immunohistochemistry, and immunoelectron microscopy. The myogenic potential, which was tested by Pax7 and MyoD expression and the formation of muscle fibers, was higher in Sk-DN cells than in Sk-34 cells but remained weak in the latter. In contrast, the capacity to differentiate into peripheral nerve and vascular cell lineages was totally stronger in Sk-34 cells. In particular, Sk-DN cells did not engraft to the damaged nerve, whereas Sk-34 cells showed active engraftment and differentiation into perineurial/endoneurial cells, endothelial cells, and vascular smooth muscle cells, similar to the human case, as previously reported. Therefore, we concluded that Sk-34 and Sk-DN cells in pigs were closer to those in humans than to those in mice.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented by x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x = 3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

Abstract: This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x=3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

This paper reports aligned activities to promote energy and resource-efficient construction practice in Vietnam. First, the governance framework is introduced, including government decrees and technical standards. Then, a laboratory with building physics measurement technology is designed and partly set up at the local partner Vietnam Institute for Building Materials (VIBM), which can be used to determine the essential characteristic values required for the implementation of energy standards. The basis for the prioritization of the characteristic values are the requirements of the National technical regulation on energy efficient buildings of Vietnam – QCVN09:2017/BXD. Furthermore, basic characteristic values from international standards are described, which can also be used for calculations to optimize the energy consumption of buildings. In order to be able to carry out transient hygrothermal computer simulations, special characteristic values were also included. These are particularly useful for the research and development of new building materials and the evaluation of entire buildings in terms of thermal and moisture protection In order to communicate the material properties to the market and enable informed decision making by the stakeholders, a labeling system has been developed. Thereby, the practical means for implementing governance instruments are provided, and the related technical applications are supported.

Background: The purpose of this study was to ascertain the reliability of two 15-sec sprint cycling tests in men and women to estimate the maximum rate of glycolysis or lactate production (VLa-Max). Methods: Eighteen men and twelve women completed two sprint sessions over 1-week. A 10-min warm-up preceded a 3 µl blood lactate (BLC) sample, after which a 15-sec sprint was completed; cyclists then rested passively while multiple lactate samples were taken until levels peaked. VLaMax was calculated as (Peak BLC – Pre BLC) * (15-sec – Talac)-1. Trial differences and reliability across trials were analyzed using a paired-sample t-test, Pearson correlation, ICC, and Bland-Altman analysis with α=0.05 for all tests; data are reported as mean ± sd. Results: Power (W) was similar across trails (773.0 ±143.5 vs. 758.2 ± 127.4; p = 0.333) and coefficient of varia-tion (CV) of 4.7%. VLaMax was similar (0.673 ± 0.024 vs 0.635 ± 0.237; p = 0.280), but only moder-ately reliably across trials with a CV, ICC, and R value of 18.6%, 0.661, and 0.67, respectively. Conclusions: A 15-sec VLaMax cycling sprint is moderately reliable being affected both by the lac-tate measurement and other variables used in the calculation. More research may offer ways to improve reliability.

To effectively estimate airport terminal area capacity and assess the maximum throughput the sector can achieve when the capacity is given, this research proposes an approach to assess the terminal area capacity from the viewpoint of service provision resources. Terminal area capacity is optimized based on the equilibrium of air traffic service resource supply and demand. The supply-demand nexus is examined in consideration of terminal area route structure, traffic flow characteristics, and safety regulations. A flight service probability matrix and a terminal area demand and supply service time model are constructed to quantify resource expenditure at varied capacity levels. A optimization model is then developed to apportion maximal capacity under resource limitations. Model computation and computation results demonstrate the deviation between estimated and amended capacities is under 0.3 flight sorties per hour. The outcomes are congruent with historical statistics, thereby validating the accuracy and reliability of the model proposed in this study. Given capacity parameters, the model can deduce the maximal aircraft quantity served concurrently in terminal areas during peak periods. These revelations indicate the submitted model furnishes theoretical foundation and reference for terminal area sector partition and traffic alerting.

This work discusses the relationship between foreign direct investment (FDI) and pollution in Spain using an autoregressive distributed lag regression model (ARDL) from 1961 to 2018. The authors apply the theoretical context of pollution haven/halo and conclude that FDI in Spain does not contribute to the transfer of green technologies for cleaner production, despite being included within the European environmental regulatory framework. The authors also verify the adequacy of the environmental Kuznets curve (EKC) and the Load Capacity Curve hypothesis (LCC) in the Spanish environmental context and find that income per capita has a positive effect on environmental sustainability and quality. In this sense, the further development of an efficient renewable energy infrastructure could efficiently drive to a better standards all pollution indexes in Spain, including nuclear energy production, contributing the emissions neutrality aimed by the EU by 2050.

The universal Debye – Mayer – Kelly hybrid model was proposed for the description of the heat capacity from 0 K to the melting points of substance within the experimental uncertainty for the first time. To describe the heat capacity, the in-house software on the base of commercial one DELPHI-7 was used with a 95% confidence level. To demonstrate the perfect suitability of this model, a thermodynamic analysis of the heat capacities of the fourth group elements, and some compounds of the A^IIIB^V and A^IIB^VI phases was carried out. It produced good agreement within the experimental uncertainty. There is no a similar model description in literature.The Similarity Method is a convenient and effective tool for critical analysis of the heat capacities of isostructural phases, which was used as an example for diamond-like compounds. Phases with the same sum of the atomic numbers of elements (Z), such as diamond and B_0.5 N_{0.5 (cub)} (Z = 6); pure silicon (Si) and Al_0.5 P_0.5 (Z=14); pure germanium (Ge) and Ga_0.5 As_0.5 (Z = 32)); pure grey tin (alpha-Sn) and In_0.5 Sb_0.5, and Cd_0.5 Te_0.5 (Z = 50) have the same heat capacity experimental values in the solid state. The proposed models can be used to both different binary and multicomponent phases. It helps to standardize the physicochemical constants.

Deep coal beds have been suggested as possible usable underground geological locations for carbon dioxide storage. Furthermore, injecting carbon dioxide into coal beds can improve the methane recovery. Due to importance of this issue, a novel investigation has been done on adsorption of carbon dioxide on various types of coal seam. This study has proposed four types of Gaussian Process Regression (GPR) approaches with different kernel functions to estimate excess adsorption of carbon dioxide in terms of temperature, pressure and composition of coal seams. The comparison of GPR outputs and actual excess adsorption expresses that proposed models have interesting accuracy and also the Exponential GPR approach has better performance than other ones. For this structure, R2=1, MRE=0.01542, MSE=0, RMSE=0.00019 and STD=0.00014 have been determined. Additionally, the impacts of effective parameters on excess adsorption capacity have been studied for the first time in literature. According to these results, the present work has valuable and useful tools for petroleum and chemical engineers who dealing with enhancement of recovery and environment protection.

Pomegranate juice (PJ) has total antioxidant capacity (TAC) which is reportedly higher compared to other common beverages. This short study aimed to evaluate the TAC of commercial PJ and pomegranate fruit in terms of a newly described iron (III) reducing antioxidant capacity (iRAC) and to compare with ABTS free radical quenching activity. Commercial PJ, freeze-dried pomegranate, and oven dried-pomegranate were analyzed. The total phenols content (TPC) was also assessed by the Folin-Ciocalteu method. The calibration results for iRAC were comparable to ABTS and Folin-Ciocalteu methods in terms of linearity (R2 > 0.99), sensitivity and precision. The TAC for PJ expressed as trolox equivalent antioxidant capacity (TEAC) was 33.4 ± 0.5 mM with the iRAC method and 36.3 ± 2.1 mM using the ABTS method. For dried pomegranates, TAC was 89–110 mmol/100 g or 76.0 ± 4.3 mmol/100 g using iRAC and ABTS methods, respectively. Freeze-dried pomegranate had 15% higher TAC compared with oven-dried pomegranate. In conclusion, pomegranate has high TAC as evaluated by the iRAC and ABTS methods, though variations occur due to the type of cultivar, geographic origin, processing and other factors. The study is relevant for attempts to refine food composition data for pomegranate and other functional foods.

The main goal of the study is to assess the Decision criteria, and the determining factor for the sustainability of entrepreneurial startups in order to contribute towards social inclusion and capacity building. Both concepts are in the development phase and are the outcome of entrepreneurial ecosystem and individual behavior and traits. The current study observed the research problem as entrepreneurship and the entrepreneurial startups are the continuous phenomena required for every economy. The lack of an efficient ecosystem and incompetent trait of an entrepreneur drags the entrepreneurial startup to a failure. Therefore, an assessment on decision criteria and determining factors categorizing them with their importance may provide requisites to lead a successful entrepreneurial startup contributing to the social inclusion and capacity building. The study solved the research problem by statistical assessment of decision criteria and determining factors and categorizing them with their importance may provide requisites to lead a successful entrepreneurial startup. The research is built on research questions, objectives, conceptual model, and hypothesis which are tested based on the data collected. The collection of data was done through a survey questionnaire on a sample of established entrepreneurs. The study concludes that five components of decision criteria are Region, Competition, Funding Opportunities, Tax System, and Country Economic Situation, whereas the eight components Consciousness and Reliable, Pursuit Results, Flexibility, Stress Resistance, Skills Identification Exploitation Potential Market Opportunities, Leadership, Creativity and Innovation, and Delegation Decision Making of determining factor are required for a successful entrepreneurial startup to be able to work towards social inclusion and capacity building.

The emerging concept of planetary health needs to be discussed in a more organized and sustainable way within the global public health and healthcare disciplines. Therefore, planetary health should be considered a cardinal component of the global academic framework for healthcare professionals. The availability of related curricula and courses is crucial to equip health professionals in this relatively new discipline of planetary health. In this review article, we aimed to explore published articles and online databases of courses to summarize the available planetary health education opportunities and discussions for health professionals, to identify the gaps in resource allocation and to suggest future recommendations. We observed a visible re-source inequity in global south with the lack of a universal planetary health module for healthcare professionals. Additionally, there is minimal inclusion of allied health disciplines in this learning process. We, therefore, recommend a dedicated network of motivated healthcare professionals and regional hubs with an agenda to ensure a comprehensive, uniform, and inclusive planetary health education curriculum and practice.

Keywords: pluripotency; naïve; stem; imprinting; primordial germ cells; trophoblast; CDK8; Mediator; enhancers.

To investigate the effect of prohexadione-calcium (Pro-Ca) primed on seed germination and seedling growth of oilseed rape under salt stress, to alleviate the inhibition of soil salinization on the growth of oilseed rape, and to improve the sustainability of agricultural production. Using Huayouza 158R and Huayouza 62 as test materials, the regulation of seed germination and seedling growth under the stresses of 0, 100, and 150 mM NaCl (S0, S100, and S150) was investigated after the primed of Pro-Ca. We conducted six treatments, S0: non-primed + 0 mM NaCl, PCS0: Pro-Ca primed + 0 mM NaCl, S100: non-primed + 100 mM NaCl, PCS100: Pro-Ca primed + 100 mM NaCl, S150: non-primed + 150mM NaCl, Pro-Ca+S150: Pro-Ca primed + 150 mM NaCl. The results showed that salt stress inhibited seed germination and seedling growth, and Pro-Ca primed significantly increased the germination index and vigor index of oilseed rape seeds. The average germination time and malondialdehyde (MDA) content were significantly reduced, which resulted in the optimal initiation fiddling concentration of 8mg·L-1. The morphological parameters of oilseed rape decreased significantly under salt stress, with leaf area decreasing by 70.69% and 75.03% and total chlorophyll content decreasing by 18.55% and 18.68% at S150. With the rise of salt stress, the changes of each photosynthetic parameter were somewhat similar, and Pn, Gs, Ci, and Tr continued to decline, indicating that the effects of salt stress on photosynthesis in oilseed rape might be mainly attributed to stomatal restriction and inhibition of photosynthetic pigment synthesis. While Na+ and MDA contents increased significantly, reaching a peak at S150, indicating that Na+ content increased significantly under salt stress, which resulted in the slow growth of oilseed rape and weak plants under the influence of Na+ salt damage. After Pro-Ca primed, leaf area and photosynthetic pigment synthesis increased, and the initiation treatment promoted the rise of Pn, Gs, Ci, and Tr under salt stress. The Na+ content decreased by 7.29% and 6.96% in PCS100 compared with S100, decreased by 9.23% and 25.02% in PCS150 compared with S150, and increased in K+ and Mg2+ after Pro-Ca primed. At this time, the antioxidant enzyme activities increased, and the MDA content and relative conductivity decreased. It was concluded that Pro-Ca primed improved the photosynthetic capacity of oilseed rape by promoting leaf growth, stomatal opening, and photosynthetic pigment synthesis. At the same time, reducing Na+ content and promoting K+ and Mg2+ absorption and antioxidant enzyme activities together alleviate salt damage and improve salt tolerance of oilseed rape.

Chemical process control relies on a tightly controlled, narrow range of margins for critical variables, ensuring process stability and safeguarding equipment from potential accidents. The availability of historical process data is limited to a specific setpoint of operation. This challenge raises issues for process monitoring in predicting and adjusting to deviations outside of the range of operational parameters. Therefore, this paper proposes simulation-assisted deep transfer learning for predicting and optimizing the final purity and production capacity of the glycerin purification process. The proposed network is trained by the simulation domain to generate a base feature extractor, which is then fine-tuned using few-shot learning techniques on the target learner to extend the working domain of the model beyond the historical practice. The result shows that the proposed model improved prediction performance by 99% in predicting water content and 79.72% in glycerin prediction over the conventional deep learning model. Additionally, the implementation of the proposed model identified the production and product quality improvement for enhancing the glycerin purification process.

The water resources carrying capacity (WRCC) system comprises multiple complex and nonlinear interactions related to society, economy, water resources and the water environment. A full understanding of its internal mechanism is conducive to the further improvement of the regional WRCC. This article focuses on the temporal and spatial variability of WRCC to explore a method of dynamic successive assessment. Firstly, the Pressure-State-Response (PSR)framework is used to develop a systematic and causal indicator system. Then, The Variable Fuzzy Pattern Recognition (VFPR) model and an analytic hierarchy process-entropy (AHP-E) model are combined to successively and dynamically assess WRCC. The proposed method is applied to the dynamic successive assessment of WRCC in Hebei Province, and it is obtained that the poor water resources carrying capacity in Hebei Province is mainly due to the basic attribute of the decision of the water resources shortage, but Hebei Province actively adopts a variety of measures to save water and pressurize mining, which makes the province's water resources carrying capacity have a tendency to become better gradually. At the same time, the system dynamics model (SD) of water resources carrying capacity based on the analysis of the model structure was established. Moreover, three scenarios were designed, including existing continuation, high-efficiency water-saving, cross-regional water transfer and coordinated development, each scenario divided into high and low-speed economic development and population growth schemes, then total 6 schemes between 2023 and 2030 were simulated and predicted respectively. The results indicate that if the current development model is adopted, the water resource carrying capacity will continue to maintain low levels. It was concluded that the high-speed development of economy and population, the efficient water conservation and inter-basin transfer scenario (scenario 2 with high-speed) is the best choice for sustainable development of water resources and social economy in Hebei.

The structural, elastic, anisotropic elastic, electronic, vibrational and properties of the Perovskite type Hydrides RbXH3 (X = Be, Ca, Mg) were performed via Vienna Ab – initio Simulation Pac-kage (VASP) based on Density Functional Theory (DFT). Our results have exhibited a well-agreement with previous calculations and experiments for each compound. In order to de-termine physical properties of RbXH3 has been used the Generalized Gradient Approximation (GGA) with Perdew-Burke-Ernzerhof (PBE) functional at this study. Present compounds were found to be mechanically stable as well as their gravimetric hydrogen storage capacities has been investigated. The Perovskite type Hydrides RbBeH3 and RbMgH3 has an indirect bandgap of 0.274 eV and 2.209 eV while RbCaH3 has a direct bandgap of 3.274 eV respectively and therefo-re these compounds has shown a semiconductor behaviour at equilibrium. Besides directional dependence of anisotropic properties was visualized by representing them with maximum - mi-nimum points..

The conservation of coastal wetland ecosystems, like mangrove forests and salt marshes, represents a critical strategy for mitigating atmospheric emissions and climate change in the 21st century. Yet the existence of these environments is threatened by human-induced disturbances, namely deforestation and accelerated sea-level rise. Coastal systems maintain surface elevation in response to sea-level rise through a combination of physical and biological processes both above and below the ground surface. The quantification and relative contribution of belowground process controls (e.g., seasonal water content, organic matter decomposition) on surface elevation change is largely unexplored but crucial for informing coastal ecosystem sustainability. To address this knowledge deficit, we integrated measurements of surface elevation change of the live root zone (0.5 to 1 m depth) with geotechnical data from co-located sediment cores in the Sundarbans mangrove forest (SMF) of southwest Bangladesh. Core data reveal that the primary belowground controls on surface elevation change include seasonal fluctuations in pore-water content and the relative abundance of fine-grained sediments capable of volumetric expansion and contraction, supporting an elevation gain of ~2.42 ± 0.26 cm yr⁻¹. In contrast to many mangrove environments, the soils of the SMF contain little organic matter and are dominantly composed (>90%) of inorganic clastic sediments. The mineral-rich soil texture likely leads to less compaction-induced subsidence as compared to organic-rich substrates and facilitates surface equilibrium in response to sea level rise. Despite a relatively high soil bulk density, soil carbon (C) density of the SMF is very low owing to the dearth of preserved organic content. However, rates of C accumulation are balanced out by locally high accretion rates, rendering the SMF a greater sink of terrestrial C than the worldwide mangrove average. The findings of this study demonstrate that C accumulation in the SMF, and possibly other alluvial mangrove forests, is highly dependent on the continued delivery of sediment to the mangrove platform and associated settings.

Galdieria maxima is a polyextremophilic alga capable of diverse metabolic processes. Ammonia is widely used in culture media typical of laboratory growth. Recent reports that this species can grow on wastes promote the concept that G. maxima might have biotechnological utility. Accordingly, there is a need to know the range of pH levels that can support G. maxima growth in a given nitrogen source. Here, we examined the combined effect of pH and nitrate/ammonium source on the growth and long-term response of the photochemical process to a pH gradient in different G. maxima strains. All were able to use differing nitrogen sources, despite both the growth rate and photochemical activity were significantly affected by the combination with the pH. All strains acidified the NH4+-medium (pH<3); only G. maxima IPPAS P507 showed reduced capacity in lowering the pH from 6.5. pH was a limiting factor in nitrate uptake at pH≥6.5; noteworthy, at pH 5 on nitrate G. maxima ACUF551 showed a good growth performance, despite the alkalization of the medium.