Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

Conventional phenotyping breeding approaches for vegetable crops like Solanaceae, Bulb, Root crops, have made a significant contribution by developing many varieties. Despite this, conventional phenotyping approaches are not sufficient due to the longer time taken to develop a variety, low genetic gain, environmental factors and some other externalities that affect the phenotype-based selection. To address the challenges of conventional phenotype, a new recent method of high throughput phenotyping (HTP) is considered a promising tool. The development of high-throughput phenotyping technology began in the preceding decade as advancements in sensor, computer vision, automation, and advanced machine learning technologies. HTP platforms are being utilized to undertake non-destructive assessments of the complete plant system in a range of crops. HTP provides the precise measurements and suggests the collection of high-quality and accurate data which is necessary for standardizing phenotyping for the collection of genetic dissection and genomic assisted breeding such as genome-wide association studies (GWAS), linkage mapping, marker-assisted selection (MAS), genomic selection (GS). The remainder of this chapter discusses how high-throughput phenotyping technologies can be used in genomic-assisted breeding for vegetable crops

Currently, large volumes of data are being collected on farms using multimodal sensor technol-ogies. These sensors measure the activity, housing conditions, feed intake, and health of farm animals. With traditional methods, the data from farm animals and their environment can be collected intermittently. However, with the advancement of wearable and non-invasive sensing tools, these measurements can be made in real-time for continuous quantitation relating to clinical biomarkers, resilience indicators, and behavioral predictors. The digital phenotyping of humans has drawn enormous attention recently due to its medical significance, but much research is still needed for the digital phenotyping of farm animals. Implications from human studies show great promise for the application of digital phenotyping technology in modern livestock farming, but these technologies must be directly applied to animals to understand their true capacities. Due to species-specific traits, certain technologies required to assess phenotypes need to be tailored ef-ficiently and accurately. Such devices allow for the collection of information that can better inform farmers on aspects of animal welfare and production that need improvement. By explicitly ad-dressing farm animals’ individual physiological and mental (affective states) needs, sensor-based digital phenotyping has the potential to serve as an effective intervention platform. Future re-search is warranted for the design and development of digital phenotyping technology platforms that create shared data standards, metrics, and repositories.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

The objective was to estimate the correlation between VIs and grain yield and identify the optimal timing and VIs for precise corn grain yield estimation. Furthermore, the study aims to employ photographic quantification to measure corn ear traits and establish their correlation with corn grain yield. Ten corn hybrids were evaluated in CRB with three rep-lications at three locations. Vegetation indices and green leaf area were estimated throughout the cycle using an unmanned aerial vehicle (UAV) and subsequently corre-lated with grain productivity. In addition, photographs were taken of the corn ear to esti-mate their length, width and total number of kernels and compare these values with manual measurements. The experiments consistently demonstrated significant experi-mental quality across sites, with accuracy ranging from 79.07% to 95.94%. UAV flights carried out at the beginning of the crop cycle revealed a positive correlation between grain productivity and the evaluated indices (NGRDI, VARI, GLI). Regarding the phenotyping of corn ears, the regression coefficients for width, length and TNG were 0.92, 0.88 and 0.62, respectively, indicating an association with manual measurements. However, stage V5 in the localities of Lavras and Ijaci and stage V8 in the locality of Nazareno showed a posi-tive correlation with productivity. The use of images for ear phenotyping is promising as a method for measuring corn components.

Phenotypic studies require large datasets for accurate inference and prediction. Collecting plant data in a farm can be very labor intensive and costly. This paper presents the design, architecture (hardware and software) and deployment of a distributed modular agricultural multi-robot system for row crop field data collection. The proposed system has been deployed in a soybean research farm at Iowa State University.

Structures inevitably suffer damages after an earthquake, with their severity ranging from minimal damages to non-structural elements to partial or even total collapse, possibly with loss of human lives. Thus, it is essential for engineers to understand the crucial factors that drive a structure towards suffering higher degrees of damage, so that preventative measures can be taken. In the present study, we focus on three well-known damage thresholds, namely Collapse Limit State, Ultimate Limit State and Serviceability Limit State and analyze which of the features obtained via Rapid Visual Screening, determine whether or not a given structure will cross that threshold. To this end, we use Machine Learning to perform binary classification for each damage threshold, as well as Explainability via SHAP values (acronym for SHapley Additive exPlanations) to quantify the effect of each parameter. The quantitative results obtained demonstrate the potential applicability of ML methods to re-calibrate the computation of structural vulnerability indices using data from recent earthquakes.

In response to escalating global demand for poultry, the industry grapples with an array of intricate challenges, from enhancing productivity to improving animal welfare and attenuating environmental impacts. This comprehensive review explores the transformative potential of digital phenotyping, an emergent technological innovation at the cusp of dramatically reshaping broiler production. The central aim of this study is to critically examine digital phenotyping as a pivotal solution to these multidimensional industry conundrums. Our investigation spotlights the profound implications of 'digital twins' in the burgeoning field of broiler genomics, where the production of exact digital counterparts of physical entities accelerates genomics research and its practical applications. Further, this review probes into the ongoing advancements in the research and development of a context-sensitive, multimodal digital phenotyping platform, custom-built to monitor broiler health. I critically evaluate this platform's potential in revolutionizing health monitoring, fortifying the resilience of broiler production, and fostering a harmonious balance between productivity and sustainability. Subsequently, the paper provides a rigorous assessment of the unique challenges that may surface during the integration of digital phenotyping within the industry. These span from technical and economic impediments to ethical deliberations, thus offering a comprehensive perspective. The paper concludes by highlighting the game-changing potential of digital phenotyping in the broiler industry and identifying potential future directions for the field, underlining the significance of continued research and development in unlocking digital phenotyping's full potential. In doing so, it charts a course towards a more robust, sustainable, and productive broiler industry. The insights garnered from this study hold substantial value for a broad spectrum of stakeholders in the broiler industry, setting the stage for an imminent technological evolution in poultry production.

Plants are such important keys of biological part of our environment, supply the human life and creatures. Understanding how the plant’s functions react with our surroundings, helps us better to make plant growth and development of food products. It means the plant phenotyping gives us bio information which needs some tools to reach the plant knowledge. Imaging tools is one of the phenotyping solutions which consists of imaging hardware such as the camera and image analysis software analyses the plant images changings such as plant growth rates. In this paper, we proposed a preprocessing algorithm to eliminate the noise and separate foreground from the background which results the plant image to help the plant image segmentation. The preprocessing is one of important levels has effect on better image segmentation and finally better plant’s image labeling and analysis. Our proposed algorithm is focused on removing noise such as converting the color space, applying the filters and local adaptive binarization step such as Niblack. Finally, we evaluate our algorithm with other algorithms by testing a variety of binarization methods.

Preschoolers with disabilities and their caregivers have been neglected in health and social service provision in most low-income countries and arguably too in low resourced areas of more affluent nations. Yet as this rapid review of published literature identifies, there are low-cost, evidence-based strategies to address their needs that can be implemented in communities by local people. Five key features of the necessary supports are examined. First the leadership functions required to create and implement the support services. Second, the family-centred, home-based support provided to caregivers and the personnel undertaking this form of support. Third, providing opportunities for peer support to flourish and encouraging the formation of advocacy groups across families. Fourth, mobilizing the support of significant groups within the community; notably traditional healers and leaders; health services and poverty alleviation initiatives. Fifth, devising ways in which preschool educational opportunities can be offered to children as a prelude to their inclusion in primary schools. The review serves a further purpose. It provides an example of how public health researchers and academics could achieve more rapid implementation of evidence-based knowledge into existing and new support services through dissemination to community practitioners.

Automated machine learning (AutoML) has been heralded as the next wave in artificial intelligence with its promise to deliver high performance end-to-end machine learning pipelines with minimal effort from the user. However, despite AutoML showing great promise for computer vision tasks, to the best of our knowledge, no study has used AutoML for image-based plant phenotyping. To address this gap in knowledge, we examined the application of AutoML for image-based plant phenotyping using wheat lodging assessment with UAV imagery as an example. We compared the performance of an open-source AutoML framework, AutoKeras in image classification and regression tasks to transfer learning using modern convolutional neural network (CNN) architectures. For image classification which classified plot images as lodged or non-lodged, transfer learning with Xception and DenseNet-201 achieved best classification accuracy of 93.2%, whereas Autokeras had 92.4% accuracy. For image regression which predicted lodging scores from plot images, transfer learning with DenseNet-201 had the best performance (R2=0.8303, RMSE=9.55, MAE=7.03, MAPE=12.54%), followed closely by AutoKeras (R2=0.8273, RMSE=10.65, MAE=8.24, MAPE=13.87%). Interestingly, in both tasks, AutoKeras models had up to 40-fold faster inference times compared to the pretrained CNNs. The merits and drawbacks of AutoML compared to transfer learning for image-based plant phenotyping are discussed.

Phenotyping is the task of measuring plant attributes for analyzing the current state of the plant. In agriculture, phenotyping can be used to make decisions concerning the management of crops, such as the watering policy, or whether to spray for a certain pest. Currently, large scale phenotyping in fields is typically done using manual labor, which is a costly, low throughput process. Researchers often advocate the use of automated systems for phenotyping, relying on the use of sensors for making measurements. The recent rise of low cost, yet reasonably accurate, RGB-D sensors has opened the way for using these sensors in field phenotyping applications. In this paper, we investigate the applicability of 4 different RGB-D sensors for this task. We conduct an outdoor experiment, measuring plant attribute in various distances and light conditions. Our results show that modern RGB-D sensors, in particular, the Intel D435 sensor, provides a viable tool for close range phenotyping tasks in fields.

Microsamples (collections usually less than 50 µL) have been introduced in pre-clinical, clinical, and research settings to overcome obstacles in sampling via traditional venipuncture. However, venipuncture remains the sampling gold standard for metabolic phenotyping of blood. This pre-sents several challenges in metabolic phenotyping workflows: accessibility for individuals in ru-ral and remote underserved areas (due to the need for trained personnel), the unamenable nature to frequent sampling protocols in longitudinal research (for its invasive nature), and sample col-lection difficulty in the young and elderly. Furthermore, venous sample stability may be compro-mised when temperate conditions necessary for cold-chain transport are beyond control. Alter-natively, research utilising microsamples extends phenotyping possibilities to inborn errors of metabolism, therapeutic drug monitoring, nutrition, as well as sport and anti-doping. Although the application of microsamples in metabolic phenotyping exists, it is still in its infancy, with whole blood being overwhelmingly the primary biofluid collected through the collection method of dried blood spots. Research into metabolic phenotyping of microsamples is limited; however, with advances in commercially available microsampling devices, common barriers such as volumetric inaccuracies and the ‘haematocrit effect’ in dried blood spot microsampling can be overcome. In this review, we provide an overview of the common uses and workflows for mi-crosampling in metabolic phenotyping research. We discuss the advancements in technologies, highlighting key considerations and remaining knowledge gaps for employment of microsamples in metabolic phenotyping research. Supporting the translation of research from the ‘bench to the community’.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Soybean maturity is a trait of critical importance for the development of new soybean cultivars, nevertheless, its characterization based on visual ratings has many challenges. Unmanned aerial vehicles (UAVs) imagery-based high-throughput phenotyping methodologies have been proposed as an alternative to the traditional visual ratings of pod senescence. However, the lack of scalable and accurate methods to extract the desired information from the images remains a significant bottleneck in breeding programs. The objective of this study was to develop an image-based high-throughput phenotyping system for evaluating soybean maturity in breeding programs. Images were acquired twice a week, starting when the earlier lines began maturation until the latest ones were mature. Two complementary convolutional neural networks (CNN) were developed to predict the maturity date. The first using a single date and the second using the five best image dates identified by the first model. The proposed CNN architecture was validated using more than 15,000 ground truth observations from five trials, including data from three growing seasons and two countries. The trained model showed good generalization capability with a root mean squared error lower than two days in four out of five trials. Four methods of estimating prediction uncertainty showed potential at identifying different sources of errors in the maturity date predictions. The architecture used solves limitations of previous research and can be used at scale in commercial breeding programs.

Hyperspectral reflectance imaging is an emerging method for rapid non-invasive quantitative screening of plant traits. This method is essential for high-throughput phenotyping and hence for accelerated breeding of crop plants as well as for precision agriculture practices. However, extraction of sensible information from reflectance images is hindered by the complexity of plant optical properties, especially when they are measured in the field. We propose using reflectance indices (Plant Senescence Reflectance Index, PSRI; Anthocyanin Reflectance Index, ARI; and spectral deconvolution) previously developed for remote sensing of vegetation and point-based reflectometers to infer the spatially resolved information on plant development and biochemical composition using ripening apple fruit as the model. Specifically, the proposed approach enables capturing data on distribution of chlorophylls and primary carotenoids as well as secondary carotenoids (both linked with fruit ripening and leaf senescence during plant development) as well as the information on spatial distribution of anthocyanins (known as stress pigments) over the plant surface. We argue that the proposed approach would enrich the phenotype assessments made on the base of reflectance image analysis with valuable information on plant physiological condition, stress acclimation state, and the progression of the plant development.

Recently, microfluidics deformability cytometry has emerged as a powerful tool for high throughput mechanical phenotyping of large populations of cells. These methods characterize cells by their mechanical fingerprints through exerting hydrodynamic forces and monitoring the resulting deformation. These devices have shown great promise for label free cytometry, yet there is a critical need to improve their accuracy and reconcile any discrepancies with other methods, such as atomic force microscopy. In this study, we employ computational fluid dynamics simulations and uncover how the elasticity of frequently used carrier fluids such as methyl-cellulose dissolved in phosphate-buffered saline is significantly influential to the resulting cellular deformation. We conducted CFD simulations that are conventionally used within the deformability cytometry field, which neglect fluid elasticity. Subsequently, we incorporated a more comprehensive model that simulates the viscoelastic nature of the carrier fluid. A comparison of the predicted stresses between these two approaches underscores the significance of the emerging elastic stresses in addition to the well-recognized viscous stresses along the channel. Furthermore, we utilize a two-phase flow model to predict the deformation of a promyelocyte (i.e. HL-60 cell type) within a hydrodynamic constriction channel. The obtained results highlight a substantial impact of the elasticity of carrier fluid on cellular deformation and raise questions about the accuracy of mechanical property estimates derived by neglecting elastic stresses.

Miscanthus holds a great potential in the frame of the bioeconomy and yield prediction can help improving Miscanthus logistic supply chain. Breeding programs in several countries are attempting to produce high-yielding Miscanthus hybrids better adapted to different climates and end-uses. Multispectral images acquired from unmanned aerial vehicles (UAVs) in Italy and in the UK in 2021 and 2022 were used to investigate the feasibility of high-throughput phenotyping (HTP) of novel Miscanthus hybrids for yield prediction and crop traits estimation. An intercalibration procedure was performed using simulated data from the PROSAIL model to link vegetation indices (VIs) derived from two different multispectral sensors. Random forest algorithm estimated with good accuracy yield traits (light interception, plant height, green leaf biomass and standing biomass) using VIs time series and predicted yield using peak descriptor derived from VIs time series with 2.3 Mg DM ha-1 of RMSE. The study demonstrates the potential of UAVs multispectral in HTP applications and in yield prediction for providing important information needed to increase sustainable biomass production.

The National Agrobiodiversity Center under the Rural Development Administration (RDA) in Jeonju, Republic of Korea, is the largest international genebank of Korea. The National Agrobi-odiversity Center has continuously been making efforts to introduce overseas genetic resources to its collection and has currently grown into a world-class PGR holding genebank. Currently, several steps are undertaken to, improve the accessibility of the collection to national as well as international researchers, improve data available on the resources and amend the passport in-formation of the accessions. With the implementation of the Nagoya Protocol, the origin of ge-netic resources is being highlighted as an important input in the passport information of germplasms. The RDA-Genebank actively responds to the Nagoya Protocol by supplementing passport data of resources lacking information on the origin of germplasm. In addition, a large number of conserved resources are continuously multiplied, and agronomic traits are investi-gated concurrently. With the traditional methods of characterization of the germplasm requiring a significant amount of time and effort, we have intiated high-throughput phenotyping using digital techniques to improve our germplasm data. Primarily, we have started adding seed phenotype information followed by measuring root phenotypes which are stored under agro-nomic traits. This may be the initial step for a germplasm center to use large-scale high-throughput techniques for their collection. In this shortcommunication, we aim to provide an introduction to the RDA- Genebank, adopted international standards, and establishment of high throughput phenotyping techniques for improvement of passport information.

Modern agriculture demands for comprehensive information about the plant itself. Conventional chemistry-based analytical methods - due to their low throughput and high associated cost - are no longer capable of providing these data. In recent years, remote reflectance-based characterization has developed as one of the most promising solutions for rapid assessments for plant attributes. However, in many cases, expensive equipment is required because accurate quantifications need assessment of the full reflectance spectrum. We examined the versatility of visible colour sensors as reflectance measuring devices for biological / biochemical quantifications on sweet basil (Ocimum basilicum). Our results indicate for the wide potential of spectral colour sensors for quantitative determination of leaf phenolic compounds, flavonoids in particular, and non-invasive plant phenotyping in agricultural applications by low-cost sensors.

Background: There is a paucity of evidence on people with thoracic aortic aneurysm and dissection. We aimed to determine the prevalence of genetic variants and associations with phenotypes. Methods: In the current cross-sectional single centre cohort study of consecutive patients who underwent endovascular or open-surgical repair of thoracic aortic aneurysm and dissection, we applied genetic analysis using four-stage Next Generation Sequencing and confirmed findings with Sanger sequencing. We collected personal and family history on comorbidities, clinical examination, anthropometrics, skeletal deformities, joint function ophthalmological measures. Cardiovascular risk- and phenotype scores were calculated. Results: 95 patients were eligible (mean age 54±9 years, 70% males, 56% aortic dissection). One-fifth had a family history of aortic disease, 95% and 54% had a phenotype score of ≤5 and ≤2, respectively. There weren’t significant differences in the distribution of phenotype characteristics according to age, sex, aortic pathology, or performed invasive procedure. Genetic variants were detected in 40% of patients; classic variants comprised 18% of all variants. We observed no significant association with cardiovascular and phenotype score but with higher joint function scores (p=.015). Conclusion: Genetic variants are highly present in clinically-relevant aortic pathologies. Variants appear to play a larger role than previously described. The different variants don’t correlate with specific phenotypes, nor with age, pathology, sex, or family history.

Type 2 diabetes (T2D) has a complex pathophysiology which makes modeling the disease difficult. We aimed to develop a novel model for simulating T2D in vitro, including hyperglycemia, hyperlipidemia, and variably elevated insulin levels targeting muscle cells. We investigated insulin resistance (IR), cellular respiration, mitochondrial morphometry and the associated function in different T2D -mimicking conditions in rodent skeletal (C2C12) and cardiac (H9C2) myotubes. Physiological controls included 5mM glucose with 20mM mannitol as osmotic controls. To mimic hyperglycemia, cells were exposed to 25mM glucose. Further treatments included insulin, palmitate, or both. After short-term (24h) or long-term (96h) exposure, we performed radioactive glucose uptake and mitochondrial function assays. Mitochondrial size and relative frequencies were assessed by morphometric analyses using electron micrographs. C2C12 and H9C2 cells treated short- or long-term with insulin and/or palmitate and HG showed IR. C2C12 myotubes exposed to T2D -mimicking conditions showed significantly decreased ATP-linked respiration and spare respiratory capacity, and less cytoplasmic area occupied by mitochondria, implying mitochondrial dysfunction. In contrast, H9C2 myotubes showed elevated ATP-linked and maximal respiration and increased cytoplasmic area occupied by mitochondria, indicating better adaptation to stress and compensatory lipid oxidation in a T2D environment. Both cell lines displayed elevated fractions of swollen/vacuolated mitochondria after T2D -mimicking treatments.Our stable and reproducible in vitro model of T2D rapidly induced IR, changes in ATP-linked respiration, shifts in energetic phenotypes, and mitochondrial morphology, which are comparable to the muscles of patients suffering from T2D. Thus, our model should allow studying disease mechanisms, potential new targets, and screen candidate therapeutic compounds.

The importance of sleep for healthy brain function is widely acknowledged. However, it remains unclear how the internal generation of dreams might facilitate cognitive processes. In this perspective we review a computational approach inspired by artificial intelligence that proposes a framework for how dreams occurring during rapid-eye-movement (REM) sleep can contribute to learning and creativity. In this framework, REM dreams are characterized by an adversarial process that, against the dream reality, tell a discriminator network to classify the internally created sensory activity as real. Such an adversarial dreaming process is shown to facilitate the emergence of real-world semantic representations in higher cortical areas. We further discuss the potential contributions of adversarial dreaming beyond learning, such as balancing fantastic and realistic dream elements, and facilitating the occurrence of creative insights. We characterize non-REM (NREM) dreams, where a single hippocampal memory is replayed at a time, as serving a complementary role of improving the robustness of cortical representations to environmental perturbations. We finally explain how subjects can become aware of the adversarial REM dreams, but less of the NREM dreams, and how the awareness phenomenon of wake, dream and lucid dreaming may appear.

The electrical motor design requires a lot of work and resources. In the field, motor designers need to decide on competitive motor sizing quickly to compete with other motor suppliers. Generally, it requires expensive FEM S/W to get accurate motor sizing results, but buying and maintaining many licenses is costly. Moreover, it needs some patience to get the result from FEM analysis. In this paper, the motor sizing technique using an existing production motor is presented to respond to urgent requests from customers without using FEM analysis. In order to enhance the fidelity of the result, magnetic flux loss by magnet coating and non-linear characteristics are considered during the motor sizing process. The proposed sizing method was verified by comparison to the FEM analysis and test result and showed reasonable confidence in them. Also, this method has the substantial advantage of outputting accurate results instantly without taking any time. It helps with the modification design of electrical motors without using expensive FEM S/W and a certain level of skill or experience.

Management practices must be developed to improve yam production sustainability. Image-based phenotyping techniques could help developing such practices based on non-destructive analyses of important plant traits. Our objective was to determine the potential of image-based phenotyping methods to assess traits relevant for tuber yield formation in yam grown in glasshouse and field. We took plant and leaf pictures with consumer cameras. We used the numbers of image pixels to derive the shoot biomass and the total leaf surface and calculated the ‘triangular greenness index’ (TGI) which is an indicator of the plant nitrogen (N) nutritional status. Under glasshouse conditions, the number of pixels obtained from nadir view (image taken top down) was positively correlated to the shoot biomass, and the total leaf surface, while the TGI was negatively correlated to the N content of diagnostic leaves. Under field conditions, pictures taken from the nadir view showed an increase in soil surface cover and a decrease in TGI with time. TGI was negatively correlated to SPAD measured on specific leaves but was not correlated to the N content of these leaves. In conclusion, these phenotyping techniques deliver relevant results but need to be further developed and validated for application in yam.

To date, various chimeric lysins have been developed as efficacious antibiotics against multidrug-resistant bacteria, but direct comparisons of their antibacterial activities have been difficult due to the preparation of multiple recombinant chimeric lysins. Previously, we reported an E. coli cell-free expression method to screen better chimeric lysins against Staphylococcus aureus, but we still needed to increase the amounts of expressed proteins enough to be able to detect them non-isotopically for quantity comparisons. In this study, we improved the previous cell-free expression system by adding a previously reported artificial T7 terminator and reversing the different nucleotides between the T7 promoter and start codon to those of the T7 phage. The new method increased the expressed amount of chimeric lysins enough for us to detect them using Western blotting. Therefore, the qualitative comparison of activity between different chimeric lysins has become possible via the adjustment of the amount variables between samples without protein purification. We applied it to select more active chimeric lysins derived from our previously reported chimeric lysin (ALS2). Finally, we compared the antibacterial activities of our selected chimeric lysins with reported chimeric lysins (ClyC and ClyO) and lysostaphin, and determined the rank orders of antibacterial activities on different S. aureus strains in our experimental conditions.

In this contribution we present work on rapid thermal annealing of as-electrodeposited thin films of Cu2ZnSnS4. The treatment was carried out in cold wall tubular reactor in dynamic conditions with variations of temperature, speed and time of the specific elements of the process. The effect of annealing was investigated by X-ray diffractometry, Raman scattering and Scanning Electron Microscopy (SEM). The phase composition of the films in dependence on conditions of treatment was analysed and have been shown that in slow and prolonged high-temperature process the low temperature binaries react completely and only Kesterite and ZnS is left. In addition, structural investigations by XRD have shown gradual decrease of crystallite sizes when the temperature level and duration of the high-temperature segment increases and respectively increase in the strain, due to formation of the phases in non-equilibrium conditions. In opposite, when the speed of dynamic segments in the process decreases the both crystallite size and strain of the Kesterite decreases non-monotonically. The grain sizes of Kesterite, presented by SEM investigations, have shown increase when the temperature and the duration increase, respectively the speed decreases with exemption at higher temperature near 750 C. The set of experiments gave idea by scrupulous analysis of Raman data to elucidate the track for fine manipulating of the defects in the structure of CZTS thin films having in mind the dependences of the ratios of Q = I287/I303 and Q’= I338/(I366+I374) on the process variables.

Road segment can be estimated from GPS trajectories by averaging. However, most existing averaging strategies suffer from high complexity or poor accuracy. For example, finding the optimal mean for a set of sequences is known to be NP-hard, while using Medoid compromises the quality. In this paper, we introduce three extremely fast and practical methods for solving the problem. The methods first analyze three descriptors and then use either a simple linear model or a more complex curvy model depending on an angle criterion. The results outperform Medoid and provide equal or better accuracy than the best existing methods while being very fast, and therefore suitable for real-time processing.

Background: Study to assess glucose levels of people with type 1 diabetes (T1D) overnight based on insulin type and timing. Methods: Real-world, retrospective study in T1D using multiple daily insulin injections. Contin-uous glucose monitoring and insulin injections data were collected for ten hours after dinner us-ing the Insulclock® connected cap. Meal events were identified using ROC detection methodology. The timing of rapid insulin, second injections, and the type of insulin analogs used were evaluat-ed. Results: Nocturnal profiles (n=775, 49 subjects) were analyzed. Higher glucose AUC over 180mg/dL was observed in delayed injections (number; %; mg/dL x h): -45-15min (n=136; 17.5%, 175.9 ±271.0); -15-0min (n= 231; 29.8%, 164.0 ±237.1); 0+45min (n= 408; 52.6%, 203.6 ±260.9), (p 0.049). The use of ultrarapid (FiAsp®) (URI) vs rapid insulin analogs (RI) was associated with less hypoglycemia events (7.1 vs 13.6%; p 0.005) and TBR70 (1.7 +6.9 vs 4.6 +13.9%; p 0.003). Us-ers of glargine U300 vs degludec had higher TIR (70.7 vs 58.5 %) (Adjusted R-squared: 0.22, p < 0.001). The use of a correction injection (n= 144, 18.6%) was associated with higher hypoglycemia events (18.1 vs 9.5%; p 0.003), TBR70 (5.5 +14.2 vs 3.0 +11.1%; p 0.003), glucose AUC over 180 mg/dL (226.1 +257.8 vs 178.0 +255.3 mg/dL x h; p 0.001), and lower TIR (56.0 +27.4 vs 62.7 +29.6 mg/dL x h; p 0.004). Conclusions: Dinner rapid insulin timing, insulin types and correction injections affect nocturnal glucose profile in T1D.

A phenotype is the composite of an observable expression of a genome for traits in a given environment. The trajectories of phenotypes computed from an image sequence and timing of important events in a plant’s life cycle can be viewed as temporal phenotypes and indicative of the plant’s growth pattern and vigor. In this paper, we introduce a novel method called FlowerPhenoNet which uses deep neural networks for detecting flowers from multiview image sequences for high throughput temporal plant phenotyping analysis. Following flower detection, a set of novel flower-based phenotypes are computed, e.g., the day of emergence of the first flower in a plant’s life cycle, the total number of flowers present in the plant at a given time, the highest number of flowers bloomed in the plant, growth trajectory of a flower and the blooming trajectory of a plant. To develop a new algorithm and facilitate performance evaluation based on experimental analysis, a benchmark dataset is indispensable. Thus, we introduce a benchmark dataset called FlowerPheno which comprises image sequences of three flowering plant species, e.g., sunflower, coleus, and canna, captured by a visible light camera in a high throughput plant phenotyping platform from multiple view angles. The experimental analyses on the FlowerPheno dataset demonstrate the efficacy of the FlowerPhenoNet.

World health is increasingly threatened by the growing number of spice-related food hazards. Further development of reliable methods for rapid, non-targeted identification of counterfeit ingredients within the supply chain is needed. ENEA has developed a portable, user-friendly photoacoustic laser system for food fraud detection, based on a quantum cascade laser and multivariate calibration. Following a study on the authenticity of saffron, the instrument was challenged with a more elusive adulterant, olive leaves in oregano. The results show that the reported method of laser sensing and chemometric analysis was able to detect adulterants at mass ratios of at least 20% in less than five minutes.

Real estate has the dual characteristics of consumption and investment. Under the inherent concept of "where there is land, there is wealth", real estate has become the investment target of the main asset. In addition to the supply and demand of the market will affect the price of real estate, many general economic factors will also have a certain impact on the price of real estate. This paper pays a special focus on the effects of MRT on housing prices, finding the closer a house is to an MRT station, the higher its price. In addition, convenience stores are very popularized, and this research report is also interested in whether the number of convenience stores within walking distance will affect the house price. In a word, these two factors do affect housing prices significantly.

The consumption of dairy products and the dairy industry is one of the main global agro-food sectors for size, economic importance and level of technology. Microbiological quality of pasteurized milk or other milk products is dependent on microbiological quality of raw milk. A variety of microbiological count methods is available for monitoring the hygienic quality of raw milk. Among them, the pour plate method is the official essay for counting the number of colony forming units in milk samples according to ISO 4833-1:2013. The aim of the present study is the validation of the Micro Biological Survey (MBS) method, against the reference plate count method, for the assessment of the microbiological quality of raw milk. This comparative study, performed in collaboration with the “Istituto Zooprofilattico Sperimentale del Lazio e della Toscana M. Aleandri” (IZSLT), demonstrates the accuracy of this alternative method for the determination of total viable bacterial count in cow’s raw milk. The results obtained with the MBS method highlighting its potential as a valid tool for reliable microbiological analysis in dairy industries.

The production and quality of Phaseolus vulgaris (snap bean) have been negatively impacted by leaf crumple disease caused by two whitefly-transmitted begomoviruses; cucurbit leaf crumple virus (CuLCrV) and sida golden mosaic Florida virus (SiGMFV), which often appear as a mixed infection in Georgia. Host resistance is the most economical management strategy against whitefly-transmitted viruses. Currently, information is not available with respect to resistance to these two viruses in commercial cultivars. In two field seasons (2018 and 2019), we screened Phaseolus sp. genotypes (n = 84 in 2018; n = 80 in 2019; most of the genotypes were common in both years with a few exceptions) for resistance against CuLCrV and/or SiGMFV. Twenty genotypes with high- to moderate-levels of resistance (disease severity ranging from 5-50%) to CuLCrV and/or SiGMFV were identified. Twenty-one genotypes were found to be highly susceptible with a disease severity of ≥66%. Adult whitefly counts differed significantly among snap bean genotypes for both years. The whole genome of these Phaseolus sp. (n=82) genotypes was sequenced and genetic variability among them was identified. Over 900 giga-base (Gb) of filtered data were generated and >88% of the resulting data were mapped to the reference genome, and SNP and Indel variants in Phaseolus genotypes were obtained. A total of 645,729 SNPs and 68,713 Indels including 30,169 insertions and 38,543 deletions were identified, which were distributed in 11 chromosomes with chromosome 02 harboring the maximum number of variants. These phenotypic and genotypic information will be helpful in genome-wide association studies that will aid in identifying genetic basis of resistance to these begomoviruses in Phaseolus sp.

We report the detection of live Escherichia coli (E. coli) in liquid samples using a biosensor based on a field effect transistor (FET) biosensor with B/N co-coped graphene oxide (GO) gel (BN-GO) as the transducer material. The FET was functionalized with antibodies to detect E. coli K12 O-antigens in phosphate-buffered saline (PBS). The biosensor detected the presence of planktonic E. coli bacterial cells within a mere 2 minutes. The biosensor exhibited a limit of detection (LOD) of 10 cells per sample, which can be extrapolated to a limit of detection at the level of a single cell per sample and a detection range of at least 10– 108 CFU/mL. The selectivity of the biosensor for E. coli was demonstrated using Bacillus thuringiensis (B. thuringiensis) as a sample contaminant. We also present a comparison of our functionalized BN-GO FET biosensor with established detection methods of E. coli k12 bacteria, as well as with state-of-the-art detection mechanisms.

In this paper, PEN3 electronic nose was used to detect and recognize fresh and moldy apples (inoculated with Penicillium expansum and Aspergillusniger) taken Golden Delicious apples as model subject. Firstly, the apples were divided into two groups: apples only inoculated with different molds (Group A) and mixed apples of inoculated apples with fresh apples (Group B). Then the characteristic gas sensors of the PEN3 electronic nose that were most closely correlated with the flavor information of the moldy apples were optimized and determined, which can simplify the analysis process and improve the accuracy of results. Four pattern recognition methods, including linear discriminant analysis (LDA), backpropagation neural network (BPNN), support vector machines (SVM) and radial basis function neural network (RBFNN), were then applied to analyze the data obtained from the characteristic sensors, respectively, aiming at establishing the prediction model of flavor information and fresh/moldy apples. The results showed that only the gas sensors of W1S, W2S, W5S, W1W and W2W in the PEN3 electronic nose exhibited strong signal response to the flavor information, indicating were most closely correlated with the characteristic flavor of apples and thus the data obtained from these characteristic sensors was used for modeling. The results of the four pattern recognition methods showed that BPNN presented the best prediction performance for the training and validation sets for both the Group A and Group B, with prediction accuracies of 96.29% and 90.00% (Group A), 77.70% and 72.00% (Group B), respectively. Therefore, it first demonstrated that PEN3 electronic nose can not only effectively detect and recognize the fresh and moldy apples, but also can distinguish apples inoculated with different molds.

One in 12 babies is born with a rare genetic disease. Sadly, most cases are undetected until later age, missing time for early treatment and opportunity to prevent complications. Humanity has entered a new era where Big Data collected by governments, including 2D and 3D facial scans, are available. Many rare genetic diseases can be identified by artificial intelligence (AI) analysis of the facial photo. Phenotyping AI utilizations facilitate comprehensive and accurate genetic evaluations. AI processing of this Big Data to identify rare genetic diseases could bring unimaginable benefits to healthcare, although this would be a questionable step in terms of citizen privacy and could lead to future "Orwellian" ramifications with government abuse. Going forward, a balance must be found between protecting the privacy of citizens and the enticing use of AI for their health risks and cost savings through prevention. The unimaginable potential of AI early diagnostics from facial photos also raises various ethical and legal concerns. This paper presents concept, protentional methods and legal and other limitations within EU legal framework in contrast with potential benefits. This paper is focused on AI utilization to early diagnostic of rare genetic diseases. Shift of paradigm in the screening for rare genetic diseases in population with AI face analysis is expected to have a significant impact. The potential of AI algorithms utilizations similar to face2gene app in general population or systematically on Big governmental datasets recording facial traits changes in time can have significant impact on public health but at the same time give raise to profound concern as violation of one’s privacy.

The coronavirus disease (COVID-19) is a respiratory tract infection caused by the new virus SARS-CoV-2. In March 2020, the World Health Organization (WHO) declared a worldwide COVID-19 pandemic. Since then, there has been a rush to find preventative or curative treatment. This arrived with the appearance of the COVID-19 vaccine, months after the declaration of the pandemic. In the setting of global COVID-19 immunization, there have been reports of rare skin immune-mediated diseases (IMD) after COVID-19 vaccination, particularly systemic sclerosis. Systemic sclerosis (SSc) is the most reported new onset IMD following messenger RNA (mRNA) COVID-19 vaccination. The pathogenesis of SSc is not fully understood, and the diagnosis is based on clinical symptoms. We report a 54-year-old male, with no prior history of autoimmune disorder, with rapid and progressive skin thickening (Modified Rodnan skin score 30/51), weeks after his mRNA COVID-19 vaccination. Antinuclear antibodies (ANA) showed a strongly positive nuclear fine-speckled pattern, but no SSc autoantibodies were found. The patient was diagnosed with SSc based on the persistence of autoantibodies and the clinical criteria according to the 2013 American College of Rheumatology/European League Against Rheumatism classification. Due to the proximity of the two events, we hypothesized a cross-reaction between COVID-19 vaccination and, in genetically predisposed patients, an emergence of systemic sclerosis. Our case suggests a potential relationship between the mRNA COVID-19 vaccine and new-onset autoimmune diseases. Physicians should be aware of this possible association.

Earthquake is among the most devastating natural disasters causing severe economic, environmental, and social destruction. Earthquake safety assessment and building hazard monitoring can highly contribute to urban sustainable development through identification and insight into optimum materials and structures. While the vulnerability of structures mainly depends on the structural resistance, the safety assessment of buildings can be highly challenging. In this paper, we consider Rapid Visual Screening (RVS) method which is a qualitative procedure for estimating structural scores for buildings suitable for medium- to high-seismic cases. This paper presents an overview of the common RVS methods, i.e., FEMA P-154, IITK-GGSDMA, and EMPI. To examine the accuracy and validation, a practical comparison is performed between their assessment and observed damage of reinforced concrete buildings from a street survey in the Bingöl region, Turkey, after the 11 May 2003 earthquake. The results demonstrate that the application of RVS methods for preliminary damage estimation is a vital tool. Furthermore, the comparative analysis showed that FEMA P-154 creates an assessment that overestimates damage states and is not economically viable while EMPI and IITK-GGSDMA provide for more accurate and practical estimation, respectively.

The importance of detecting bacteria in various food products is ever-increasing, due to recent food trends that lend themselves to food contamination. Additionally, the detection of probiotics in food products is of increasing importance to consumers, who realize the benefits of probiotics on one’s diet. Existing technologies for detection of bacteria in food are accurate, but most are slow, increasingly costly and unsuitable for applications outside of research laboratories. Optic approaches have recently emerged as an alternative, allowing rapid detection of bacterial presence. This study employs a portable kinetics fluorometer, fabricated in-house, in conjunction with NADH sensitive fluorescence reporter for analysis of various food products. The presence of bacteria is detected in 5 minutes. Both pathogenic and probiotic bacteria were detected in food products, such as raw chicken and beef, spoiled lettuce and contaminated water, yogurt, and kombucha tea. The cellular activity of two probiotic pills was also verified. All samples displayed varying levels of bacterial activity. The study indicates the viability of biosensors being used as an alternate method to detect bacteria in food products – and the viability of a fluorescence-based biosensor to detect viable bacteria. The approach is suitable for both laboratory and field determinations.

The moisture content of maize seed is an important indicator for evaluating seed quality and a fundamental item in grain testing. The experiment used direct drying method to measure the moisture content of 80 different varieties of maize samples, and captured their images using a hyperspectral imaging (HSI) system in the spectral range of 1100~2498nm. By comparing seven spectral preprocessing methods, the PLSR model established after Normalize pretreatment had the best effect. The characteristic wavelengths were selected by Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS) and Uninformative Variable Elimination (UVE). Twelve prediction models were established for full band spectra and characteristic wavelengths based on PLSR, PCR and SVM. By comparing the performance of the prediction models, it was found the Normalize-SPA-PLSR algorithm was optimized. The values of RC2 and RP2 in the model were higher, which were 0.9936 and 0.9933, respectively, while the values of RMSEP and RMSECV were lower, which were 0.0357 and 0.0380, respectively. The Normalize-SPA-PLSR model was used as a visual prediction model for moisture content of maize seed, the 20 maize varieties in the prediction set were visualized to obtain visualized color images of moisture content. The color differences between different moisture content images were significant. The result indicated that hyperspectral imaging could accurately, rapidly, and non-destructive predict moisture content of maize seed, which provided technical support for moisture content detection in the process of maize harvest, storage and processing.

Positive Health (PH) has been described as a promising transformative innovation to address the challenges of promoting well-being and reducing the burden of disease. The aim of this study is to review the current state of knowledge about PH as introduced by Huber et al. (2016) within the available scientific literature. A rapid review of the literature following the Cochrane Rapid Review recommendations. Three databases were searched (PubMed, Google Scholar, and CINAHL). Data were extracted and synthesized using a narrative approach. A total of 55 articles were included. Initial evaluation studies reveal promising results both at individual and collective levels. However, a need is expressed in several articles for further refinement of the conceptualization of PH and ways to make the effects of the PH approach more measurable. Professionals also expressed a desire for a more informed application and elaboration of the PH method across various settings and populations to enhance its effectiveness in practice. This rapid review highlights the transformative potential of PH in shifting from a disease-focused to a health-oriented paradigm of healthcare. It underscores the need for continued research regarding further development of the concept and its practical method, along with the necessity for methodological innovation.

Despite the increasing popularity of liquid chromatography-mass spectrometry (LC-MS)-based lipidomics, there is a lack of accepted and validated method for lipid extract quality and quantity assessment prior to LC-MS. Fourier-Transform Infrared Spectroscopy (FTIR) has been reported for quantification of pure lipids, however, the sample complexity and purity complex lipid extract quantification in lipidomics experiments could be impact quantification accuracy. Here, we report comprehensive assessment of the sample matrix on the accuracy of lipid quantification using Attenuated Total Reflectance Fourier-Transform Infrared Spectroscopy (ATR-FTIR). Pure lipids are characterized by CH-and C=O-stretching vibrations on FTIR, with quantitative range of 40–3000 ng and a limit of detection of 12 ng. Sample extraction method and local baseline subtraction during FTIR spectral processing significantly impact lipid quantification by CH-stretching. To facilitate sample quality screening, we developed the Lipid Quality (LiQ) score from a spectral library of common contaminants, using a ratio of peak heights between CH-stretching vibrations maxima and the collective vibrations from amide/amine, CH-stretching minima and sugar moieties. We evaluated LiQ score as a rapid sample quality control method by comparing to total LC-MS intensity of targeted lipidomics of 107 human plasma lipid extracts. Exclusion of poor-quality samples based on LiQ score improved the correlation between FTIR and LC-MS quantification. Finally, the uncertainty of absolute quantification by FTIR was estimated using a 795 ng SPLASH LipidoMix standard to be &lt;10%. In summary, this study identified key parameters for accurate FTIR-based quantification of complex lipid mixture, and developed a rapid workflow requiring only 1 µL of MS-ready sample and &lt; 5 minutes for routine lipidomics sample quality and quantity assessment.

Biosensors have shown great potential in realizing rapid, low cost and portable on-site detection for diseases. This work reports the development of a new bioelectronic sensor called AC electrokinetics-based capacitive (ABC) biosensor, for the detection of genomic DNA (gDNA) of methicillin-resistant Staphylococcus aureus (MRSA). The ABC sensor is based on interdigitated microelectrodes biofunctionalized with oligonucleotide probes. It uses a special AC signal for direct capacitive monitoring of topological change on nanostructured sensor surface, which simultaneously induce dieletrophoretic enrichment of target gDNAs. As a result, rapid and specific detection of gDNA/probe hybridization can be realized with high sensitivity. It requires no signal amplification such as labelling, hybridization chain reaction, or nucleic acid sequence-based amplification. This method involves only simple sample preparation. After optimization of nano-structured sensor surface and signal processing, the ABC sensor demonstrated fast turnaround of results (~10 s detection), excellent sensitivity (a detection limit of 4.7 DNA copies /µL MRSA gDNA) and high specificity, suitable for point of care diagnosis. As a bioelectronic sensor, the developed ABC sensors can be easily adapted for detection of other infectious agents.

Background: First-line biological diagnosis of malaria in Mali is based on the use of rapid diagnostic tests (RDT), which detect in the blood the Histidin Rich Protein 2 antigen, specific to Plasmodium falciparum. Our study, based on a real-time polymerase chain reaction (qPCR) gold-standard diagnosis, aims to evaluate the performance of RDTs used in Mali and to describe the distribution of Plasmodium species in each administrative regions of Mali; Methods: We collected RDT cassettes in 47 sites of the nine regions of Mali. We randomly selected 150 malaria-negative and up to 30 malaria-positive RDTs from each regions. DNA was extracted from the RDTs’ nitrocellulose strip and then assayed with a pan-Plasmodium qPCR. Positive samples were then analyzed with qPCRs specific for P. falciparum, P. malariae, P. vivax, and P. ovale; Results: Of the 1,389 tested by qPCR RDTs, 258 (18.6%) were positive for Plasmodium spp. P.falciparum was the most predominant (97.3%). However, the prevalence of P.vivax reach 21.1% in the Ménaka region in the north; Conclusion: Overall, RDT diagnostic indices are adequate for the biological diagnosis of malaria in Mali. Our finding support the adjustment of RDTs to the local epidemiology.

This study reports the design of a dielectric resonator (DR) metasurface-based terahertz biosensor for rapid and accurate detection of different kinds of viruses (H1N1, SARA-COV-2, etc.). The characterization of the sensor is done by analyzing its absorbance properties with and without the presence of the H1N1 virus layer of different concentrations and electrical properties in the frequency range of 2.4 THz to 3 THz. A full-wave EM model of the sensor is designed using CST MWS software. The geometrical parameters of the proposed biosensor, as well as its dielectric constant of the virus swab, are varied to achieve good performance with an absorption level close to 1 (100%). A significant change in the resonating pick-up frequency owing to the variation in the effective refractive index of the realized sensor ensures the detection and classification of the different concentrations of the same or different viruses. The presented design could be used for the rapid detection of viruses with the added advantages of contactless, label-free, and accurate identification of different concentrations of viruses.

Tumour spheroids are fast becoming commonplace in basic cancer research and drug development. Obtaining high-quality data relating to the inner structure of spheroids is important for analysis, yet existing techniques often use equipment that is not commonly available, are expensive, laborious, cause significant size distortion, or are limited to relatively small spheroids. We present a high-throughput method of mounting, clearing, and imaging tumour spheroids that causes minimal size distortion. Spheroids are mounted in an agarose gel to prevent movement, cleared using a solution prepared from commonly available materials, and imaged using confocal microscopy. We find that our method yields high quality two- and three-dimensional images that provide information about the inner structure of spheroids.

Recently it was found from Cassini data that the mean recession speed of Titan from Saturn is v = 11.3 ± 2.0 cm/yr which corresponds to a tidal quality factor of Saturn Q ≈ 100 while the standard estimate yields Q ≥ 6 · 10⁴ . It was assumed that such a large speed v is due to a resonance locking mechanism of five inner mid-sized moons of Saturn. In this paper, we show that an essential part of v may come from a local Hubble expansion, where the Hubble-Lemaˆıtre constant H0 recalculated to the Saturn-Titan distance D is 8.15 cm/(yrD). Our hypothesis is based on many other observations showing a slight expansion of the Solar system and also of our Galaxy at a rate comparable with H0. We demonstrate that the large disproportion in estimating the Q factor can be just caused by the local expansion effect. [Accepted for publication in "Gravitation and Cosmology". The paper is to appear in Vol. 28, Issue 2 (2022) of the journal Gravitation and Cosmology.]

Five-day exposure of clary sage (Salvia sclarea) to 100 μM cadmium (Cd) in hydroponics was sufficient to increase Cd concentrations significantly in roots and aboveground parts and affect negatively whole plant levels of calcium (Ca) and magnesium (Mg), since Cd competes for Ca channels, while reduced Mg concentrations are associated with increased Cd tolerance. Total zinc (Zn), copper (Cu), and iron (Fe) uptake increased but their translocation to the aboveground parts decreased possible due to translocation barriers. Despite the substantial levels of Cd in leaves, without any observed defects on chloroplast ultrastructure, an enhanced photosystem II (PSII) efficiency was observed, with a higher fraction of absorbed light energy to be directed to photochemistry (ΦPSΙΙ). The concomitant increase in the photoprotective mechanism of non-photochemical quenching of photosynthesis (NPQ) resulted in an important decrease in the dissipated non-regulated energy (ΦNO), modifying the homeostasis of reactive oxygen species (ROS), through a decreased singlet oxygen (1O2) formation. Thus, when clary sage was exposed to Cd for a short period, tolerance mechanisms were triggered, with PSII photochemistry to be regulated by NPQ in such a way that PSII efficiency to be enhanced. However, exposure to a combination of Cd and high light or for longer duration (8 days) to Cd alone, resulted in an inhibition of PSII functionality pointing out towards Cd toxicity. Thus, the rapid activation of PSII functionality at short time exposures and the inhibition at longer duration suggests a hormetic response and describes these effects in terms of “adaptive response” and “toxicity”, respectively.

COVID-19 represents an unprecedented threat to global public health and economies. Assays are urgently needed for rapid detection and diagnosis of SARS-CoV-2-infected patients in order to inform treatment and quarantine strategies. Establishing globally accepted easy-to-access diagnostic tests is extremely important to understanding the epidemiology of the present pandemic. While nucleic acid-based tests are considered to be more sensitive with respect to serological tests, but the present gold standard RT-PCR-based assays possess limitations such as low sample throughput, requirement for sophisticated reagents and instrumentation. To overcome these shortcomings, recent efforts of incorporating LAMP-based isothermal detection, and minimizing the number of reagents required are on rise. Novel CRISPR- and other nuclease-based techniques, when merge with isothermal and allied technologies, promises to provide sensitive and rapid detection of SARS-CoV-2 nucleic acids. Here we discuss and present compilation of state-of-the-art CRISPR based detection techniques for use in COVID diagnosis and epidemiology.

A common motivation for increasing open access to research findings and data is the potential to create economic benefits – but evidence is patchy and diverse. This study systematically reviewed the evidence on what kinds of economic impacts (positive and negative) open science can have, how these comes about, and how benefits could be maximized. Use of open science outputs often leaves no obvious trace, so most evidence of impacts is based on interviews, surveys, inference based on existing costs, and modelling approaches. There is indicative evidence that open access to findings/data can lead to savings in access costs, labour costs and transaction costs. There are examples of open science enabling new products, services, companies, research and collaborations. Modelling studies suggest higher returns to R&D if open access permits greater accessibility and efficiency of use of findings. Barriers include lack of skills capacity in search, interpretation and text mining, and lack of clarity around where benefits accrue. There are also contextual considerations around who benefits most from open science (e.g. sectors, small vs larger companies, types of dataset). Recommendations captured in the review include more research, monitoring and evaluation (including developing metrics), promoting benefits, capacity building and making outputs more audience-friendly.

This study explores the innovative use of CO2 laser technology in frenuloplasty, a significant shift from traditional methods like scalpel surgery or electrocautery, towards a minimally invasive approach. The research involved 15 patients aged 25 to 50, undergoing frenuloplasty with a CO2 laser system equipped with a 7-inch defocused handpiece, set at 20Hz and 0.3W. This method diverges from conventional laser techniques, focusing on controlled laser passes combined with manual traction to elongate the fibrous tissue of the frenulum. The results demonstrated that the CO2 laser technique allowed for a precise and progressive modification of the frenulum, significantly reducing the risks of hemorrhage and secondary in-tention fibrosis. The healing process was notably expedited, with patients reporting satisfactory outcomes within a two-week period. Statistically significant improvements were observed in pa-tient-reported outcomes, as evidenced by the increases in the Short Form Health Survey (SF-12) scores, with the mean Physical Component Summary (PCS) score rising from 32.5 to 47.5 and the mean Mental Component Summary (MCS) score from 39.3 to 52.3 (p < 0.001 for both). The study concludes that CO2 laser frenuloplasty is an effective and safe technique, offering sub-stantial benefits in terms of reduced healing time and enhanced patient satisfaction. The signifi-cant improvements in SF-12 scores underscore the positive impact on patient quality of life, ad-vocating for the broader application of this technique in clinical practice. Further research is warranted to explore its potential in a wider clinical context.

A rapid and efficient method using an alkyl functionalized magnetic nanoparticles-based extraction technique combined with Ultra-High Performance Liquid Chromatography was developed for the detection of trace amounts of polycystic aromatic hydrocarbons in tea leaves. As a popular coating for chromatographic column packing materials, C18-alkyl has been demonstrated to be effective in separating polycystic aromatic hydrocarbons. And the magnetism of the nanomaterials accelerates the extraction process while their high surface ratio enables desirable dispersity in the sample matrix. Meanwhile, the adsorbents can be washed and reused 30 times without compromise on recovery, which greatly reduced the budget. The effects of various parameters were investigated and optimized, and the recoveries for five analytes were in the range of 84.8–103.7%. The reproducibility rate of intra-day and inter-day were below 7.1% and 11.3% respectively. The limits of detection and limits of quantification ranged from 1.69–9.97 ng g-1 and 5.12–30.21 ng g-1, indicating satisfactory sensitivity. Thus, the proposed methodology is rapid, highly efficient, and economical, and it expands the application of magnetic cleanup approaches in complex food matrices.

Background: The epidemiological situation generated by COVID-19 has cast into sharp relief the delicate balance between public health priorities and the economy, with businesses obliged to toe a line between employee health and continued production. In an effort to detect as many cases as possible, isolate contacts, cut transmission chains and limit the spread of the virus in the workplace, mass testing strategies have been implemented in both public health and industrial contexts to minimize the risk of disruption in activity. Objective: To evaluate the economic impact of mass workplace testing strategy as carried out by a large automotive company in Catalonia in terms of health and healthcare resource savings. Methodology: Analysis of health costs and impacts based on the estimation of mortality and morbidity avoided because of screening and the resulting savings in healthcare costs. Results: The economic impact of the mass workplace testing strategies (using both PCR and RAT tests) was approximately €10.44 per test performed or €5,575.49 per positive detected. 38% of this figure corresponds to savings derived from better use of health resources (hospital beds, ICU beds and follow-up of infected cases), while the remaining 62% corresponds to improved health rates due to avoided morbidity and mortality. In scenarios with higher positivity rates and a greater impact of the infection on health and the use of health resources, these results could be up to ten times higher (€130.24 per test performed or €69,565.59 per positive detected). Conclusion: In the context of COVID-19, preventive actions carried out by the private sector to safeguard industrial production also have concomitant public benefits in the form of savings in healthcare costs. Thus, governmental bodies need to recognize the value of implementing such strategies in private settings and facilitate them through, for example, subsidies.

Background: This year has seen the emergence of two major crises, a significant increase in frequency and severity of hurricanes and the COVID-19 pandemic. However, little is known as to how each of these two events have impacted the other. A rapid qualitative assessment was conducted to determine the impact of the pandemic on preparedness and response to natural disasters and the impact of past experiences with natural disasters in responding to the pandemic. Methods: Semi-structured interviews were conducted with 26 representatives of 24 different community-based programs in southern Louisiana. Data were analyzed using procedures embedded in the Rapid Assessment Procedure – Informed Community Ethnography methodology, using techniques of immersion and crystallization and focused thematic analysis. Results: The pandemic has impacted the form and function of disaster preparedness, making it harder to plan for evacuations in event of a hurricane. Specific concerns included being able to see people in-person, providing food and other resources to residents who shelter in place, finding volunteers to assist in food distribution and other forms of disaster response, competing for funds to support disaster-related activities, developing new support infrastructures, and focusing on equity in disaster preparedness. However, several strengths based on disaster preparedness experience and capabilities were identified, including providing a framework for how to respond and adapt to COVID and integration of COVID response with their normal disaster preparedness activities. Conclusions: Although prior experience has enabled community-based organizations to respond to the pandemic, the pandemic is also creating new challenges to preparing for and responding to natural disasters.

Bangladesh has adopted some special steps to control the quick spread of the COVID-19 pandemic situation. However, the local residents’ knowledge, attitudes, and practices towards the disease have a direct impact on the success of the controlling measures taken by the state. This article explores knowledge (K) about preventions, attitude (A) to the disease, and practices (P) of preventing COVID-19 situation of the young age groups residing in Bangladesh. Quantitative data were collected online using a KAP questionnaire from 932 participants. Results show the population is generally aware of the symptoms, keeping social distance by staying home and are concerned about re-spreading after the lock-down period. However, they are quite unsure about the possible medicines frequently talked about in the media and the necessity of avoiding animal protein. One of the major limitations is, these findings should not be generalized due to the low number of participants compared to the total population in Bangladesh.

As a part of our ongoing research on endophytic fungi, we have isolated a sesterterpene mycotoxin, fusaproliferin (FUS), from Fusarium solani strain associated with the plant Aglaonema hookerianum Schott. FUS showed rapid and sub-micromolar IC₅₀ against pancreatic cancer cell lines. Time dependent survival analysis and microscopy imaging showed rapid morphological changes in cancer cell lines 4 hours after incubation with FUS. This provides a new chemical scaffold that can be further developed to obtain more potent synthetic agents against pancreatic cancer.

Imaging living cells by atomic force microscopy (AFM) promises not only high-resolution topographical data, but additionally, mechanical contrast, which are not obtainable with other microscopy techniques. Such imaging is however challenging, as cells need to be measured with low interaction forces to prevent either deformation or detachment from the surface. Off-resonance modes which periodically probe the surface have been shown to be advantageous, as they provide excellent force control combined with large amplitudes, which help reduce lateral force interactions. However, the low actuation frequency in traditional off-resonance techniques limits the imaging speed significantly. Using photothermal actuation, we probe the surface by directly actuating the cantilever. Due to the much smaller mass that needs to be actuated, the achievable measurement frequency is increased by two orders of magnitude. Additionally, photothermal off-resonance tapping retains the precise force control of conventional off-resonance modes and is therefore well suited to gentle imaging. Here we show how photothermal off-resonance tapping can be used to study live cells by AFM. As an example of imaging mammalian cells, the initial attachment, as well as long term detachment of a human thrombocytes are presented. The membrane disrupting effect of the antimicrobial peptide CM-15 is shown on the cell wall of E. coli. Finally, the dissolution of the cell wall of B. subtilis by lysozyme is shown. Taken together, these evolutionarily disparate forms of life exemplify the usefulness of PORT for live cell imaging in a multitude of biological disciplines.

Background: The COVID 19 pandemic and associated public health measures have disrupted the lives of people around the world. It is already evident that the direct and indirect psychological and social effects of the COVID 19 pandemic are insidious and affect the mental health of young children and adolescents now and will in the future. The aim and objectives of this knowledge-synthesis study were to identify the impact of the pandemic on children’s and adolescent’s mental health and to evaluate the effectiveness of different interventions employed during previous and the current pandemic to promote children’s and adolescent’s mental health. Methodology: We conducted the systematic review according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines and included experimental randomized, nonrandomized controlled trials; observational studies; and qualitative studies. Results: Of the 5,828 articles that we retrieved, 18 articles met the inclusion criteria. We thematically analyzed and put up the major findings under the thematic areas of impact of pandemic on children and adolescent’s mental health. These studies reported that pandemics cause stress, worry, helplessness, and social and risky behavioral problems among children and adolescents (e.g., substance abuse, suicide, relationship problems, academic issues, absenteeism from work). Interventions such as art-based programs, support services, and clinician-led mental health and psychosocial services effectively decrease mental health issues among children and adolescents. Conclusion: Children and adolescents are more likely to experience high rates of depression and anxiety during and after a pandemic. It is critical that future researchers explore effective mental health strategies that are tailored to the needs of children and adolescents. Explorations of effective channels regarding the development and delivery of evidence-based, age-appropriate services are vital to lessen the effects and improve long-term capacities for mental health services for children and adolescents.

This study aims to construct simple devices to ascertain the concentrations of ammonium (NH4+) and nitrate (NO3-). The device structure comprises a visible and near-infrared absorption meas-urement room, along with an RGB (red, green, and blue) absorption measurement room, con-stituting the two measuring rooms. Both the measurement rooms are equipped with light sources and detectors configured to operate in opposed or thru-beam modes. A tiny processor is utilized for processing the measurements, with an algorithm implemented within its memory. During the algorithm development phase, ranges for measuring the quantity of nutrients were categorized using a discriminant analysis approach. Thirty percent of the soil sample data were utilized as verification data, while the remaining 70 percent served as training data. Nutrient content values from reliable measuring instruments were incorporated into all datasets. Discriminant analysis was employed to classify the amount of NH4+ into five ranges based on the test results. When tested with soil samples, the accuracy was 66.13% compared to the reference value of a reliable measuring device. Similarly, NO3- was classified into four ranges with an accuracy of 81% com-pared to the reference value of a reliable measuring device.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including pressure of 3.8 MPa (3 tons), temperature of 80oC, and 3 minutes of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. Wicking speed in the fabricated paper strips was slightly slower than that of non-processed paper, resulting from reducing paper pore size. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper device from this fabrication process is potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

Earthquake-triggered landslides are one of the most significant hazards worldwide. These landslides, involving small or large volumes, can develop in debris flow or avalanche with high mobility and long-runout distance. The motion processes of this kind of landslide also quite complicated. This study reproduced the motion processes of two landslides using the LS-RAPID program. The Aso Bridge landslide occurred on April 16, 2016, with rapid and long-runout distance characteristics. The Kataragai landslide occurred on April 9, 2018, travelling with flow-like behavior. Through field investigations and laboratory experiments, features and mechanical parameters of these two landslides were obtained. In the LS-RAPID program, the pre-failure models and motion processes of these two landslides were established and reproduced. Results indicated that sliding speed and travelling morphology at different intervals were considered as two indicators to describe their motion process. However, while sliding speed of these two landslides have significant differences with sliding speeds of actual landslides, the final morphologies after failure were consistent with those observed in the field investigation.

The chromatographic conditions were optimized using headspace gas chromatography, and a simple and rapid method was established for the simultaneous determination of five residual solvents in ursodeoxycholic acid raw materials. The corresponding quality standards were revised. The results showed that the concentration of methanol ranged from 0.06mg/ml to 0.3mg/ml, and the concentrations of acetone, tert butanol, ethyl acetate, and triethylamine showed a good linear relationship with the peak area within the range of 0.1mg/ml to 0.5mg/ml (r=0.999); The quantitation limits for methanol, acetone, tert-butanol, ethyl acetate, and triethylamine were 4.2, 0.9, 1.5, 1, and 0.1 μg/ml, respectively, with detection limits of 1.2, 0.25, 0.025, 0.3, and 0.025 μg/ml, respectively. The recovery rates of each solvent ranged from 92.9% to 106.0%, with RSD% (n=9) less than 3.8%; The method exhibited good repeatability, with RSD% (n=6) less than 2.5%. Furthermore, the durability is good. The established method is simple, accurate, specific, and highly sensitive, and can be used for the simultaneous and rapid determination of five residual solvents in ursodeoxycholic acid raw materials.

In this paper, a system of searching for optimal paths is developed and concreted on a FPGA. It is based on a memristive emulator, used as a delay element, by configuring the test graph as a memristor network. A parallel algorithm is applied to reduce computing time and increase efficiency. The operation of the algorithm in Matlab is checked beforehand and then exported to two different Intel FPGAs: a DE0-Nano board and an Arria 10 GX 220 FPGA. In both cases reliable results are obtained quickly and conveniently, even for the case of a 300x300 nodes maze.

The testing requirements of the active phased array antennas are very different from those of traditional passive antennas, due to its beam steering capability. Usually, each beam profile of the active phased array needs a separate radiation pattern test, which makes the overall testing time extremely long. Thus the traditional antenna test method can no longer meet the efficiency and cost requirements of new active phased array antennas test. In this paper, a fast test method tailored for phased array antennas is proposed that offers significantly reduced testing time at the expense of slight sacrifice of the accuracy. Using the simulated element pattern in array and ideal port excitation, the beam profile in any direction can be predicted by testing only a certain beam profile. Through theoretical derivation and experiments, the effectiveness of the method is verified, and the testing efficiency of the phased array antenna is demonstrated to be improved by ten times or even more.

Nepal, primarily an agricultural country, heavily relies on agricultural residue and fuelwood for daily energy requirements. In 2022, total energy consumption was 640 PJ, with traditional sources accounting for 64.17%, and fuelwood comprising 58.53% of total fuel consumption. The estimated potential supply of agricultural residue is 26 million tonnes, yielding about 442 million GJ of energy in 2021. Biomass trading often emphasizes volume or weight, necessitating a rapid and non-destructive assessment of energy properties for mutual benefit, aiding in the identification, management, and utilization of biomass sources. In this study, 200 biomass samples were collected in two batches (126 and 74 samples) from various locations in Nepal. Using Partial Least Squares Regression (PLSR), a model was developed correlating higher heating value (HHV) from a bomb calorimeter and spectral data from Fourier Transform near-infrared spectroscopy (FT-NIRS) (3595 – 12,489 cm-1) sensor. PLSR models incorporated raw spectra, eight preprocessing techniques, the multi-preprocessing five-range method, and a genetic algorithm. Outliers in the first batch were identified, and the first batch divided into an 80% calibration set and a 20% validation set, while the second batch was designated as an unknown sample set. The optimum PLSR model, utilizing first derivative preprocessing, improved accuracy by 6.77%, with coefficients of determination in the calibration set, validation set, and unknown set as 0.9694, 0.9578, and 0.8089, respectively. Root mean square errors were 132.4790 J/g, 189.4800 J/g, and 360.8845 J/g for the calibration set (RMSEC), validation set (RMSEP), and unknown set (RMSEUN), respectively. The prediction to deviation ratio (RPD) for the validation set and unknown set was 4.9 and 2.4, respectively. The cross validation model of combined sample data of every sets showed the R2CV of 0.95 and RPDCV of 4.6 indicating the model could serve as a reliable and swift non-destructive alternative for evaluating biomass HHV using NIRS and ready for updating for industrial use. However, incorporating a larger number of representative samples is crucial to enhance accuracy and develop a more comprehensive global model for predicting biomass HHV.

Rapidly progressive glomerulonephritis, the term coined for a subtype of nephritic syndrome, is characterized by a state of acute loss of renal function, along with those components of renal damage on urinalysis, over a relatively short period (a few weeks or months). It is the aftermath of an acute, severe glomerular injury. RPGN, famously known as Crescentic glomerulonephritis (cGN) is not a single disease entity but a pattern that can occur in a variety of glomerular diseases caused by different pathologic lesions leading to the development of necrosis in the glomerular capillaries seen in both, systemic and kidney-restricted diseases. While still little is known about the exact etiologic cause behind the primary injury to the capillary wall leading to the development of the condition, many mechanisms are put forth to describe the pathogenesis leading to the progression. Immunopathologic studies have demonstrated that rapidly progressive glomerulonephritis can result from glomerular antibody deposition, can be immune complex-mediated, or from some as yet undefined mechanism that doesn’t involve glomerular antibody deposition. The condition is often severe with poor prognosis as it develops so rapidly and with extensive glomerular involvement, the damage is almost irreversible. Many elements can be associated with the occurrence and progression of the disease but it often involves a disruptive immune response one way or the other. RPGN’s morphological hallmark, the extensive extra-capillary cellular proliferation into the bowman’s space, commonly known as crescent formation which is often observed by electron microscopic view of the tissue biopsy, is considered one of the great diagnostic approaches for the detection of the disease. Also, the severity of the disease is related to the nature and type of immunologic process causing the disease and (in part) to the degree of crescent formation, that can only be observed by histopathological studies. This activity attempts to explain the etiology and pathogenesis involved in the development leading to the rapid progression of the disease.

This study reports the preparation of silica and nano-fructosome encapsulated Candida antarctica lipase B particles (CalB@NF@SiO2) and demonstration of their enzymatic hydrolysis and acylation. CalB@NF@SiO2 particles were prepared as a function of TEOS concentration (3-100 mM). Their mean particle size was 185 nm by TEM. Enzymatic hydrolysis was performed to compare catalytic efficiencies of CalB@NF and CalB@NF@SiO2. Catalytic constants (Km, Vmax, and Kcat) of CalB@NF and CalB@NF@SiO2 were calculated with Michaelis-Menten equation and Line-weaver Burk plot. Optimal stability of CalB@NF@SiO2 was found at pH 8 and temperature of 35 ℃. Moreover, CalB@NF@SiO2 particles were reused for seven cycles to evaluate their reusability. In addition, enzymatic synthesis of benzyl benzoate was demonstrated by an acylation reaction with benzoic anhydride. The efficiency of CalB@NF@SiO2 for converting benzoic anhydride to benzyl benzoate by the acylation reaction was 97%, indicating that benzoic anhydride was almost completely converted to benzyl benzoate. Consequently, CalB@NF@SiO2 particles are better than CalB@NF particles for enzymatic synthesis. In addition, they are reusable with high stability at optimal pH and temperature.

In the last decade, robotic-mediated rehabilitation has emerged as a potential solution to improve repetitive task training. Each device in this field has a unique development history shaped by engineers’ expertise in specific programming languages or platforms. In this work we adopt an approach that tries to abstract from the final implementation with the aim to make control logic more shareable and understandable. The authors will present the outcomes of the application of a Rapid Control Prototyping strategy to an upper-limb robotic exoskeleton. A model-based design approach implemented on a real-time target machine is presented. This modern design approach was explored with several control strategies and was used to test the exoskeleton’s performances. The proposed method highlights how it is possible to develop the entire control architecture in a single programming environment.

The COVID-19 pandemic caused by the virus SARS-CoV-2 has been the greatest global threat to human health in the last three years. The most widely used methodologies for the diagnosis of COVID-19 are quantitative reverse transcription polymerase chain reaction (RT-qPCR), used to detect the viral genome, and rapid antigen tests (RATs), also known as lateral flow tests, that employ specific antibodies to detect the viral spike protein. While PCR is considered the gold standard test in terms of specificity and sensitivity, it is time-consuming and requires specialized instrumentation operated by skilled personnel. In contrast, RATs can be used in-home or at point-of care but are less sensitive leading to a higher rate of false negative results. An alternative methodology for the detection of virus is the use of electrochemical biosensors that employ disposable strip electrodes to which binding of viral components elicits a change in electrical signal. Laser-scribed graphene (LSG) electrodes are attractive candidates for use as biosensors electrodes suitable for SARS-COV-2 detection due to their low-cost, patternability and ease of fabrication. In this work, we describe the development of a biosensor for COVID-19 detection that exploits a split-ester bond ligase system (termed ‘EsterLigase’) for immobilization of a virus-specific nanobody to maintain the out-of-plane orientation of the probe to ensure the efficacy of the probe-target recognition process. An anti-spike VHH E nanobody, genetically fused with the EsterLigase domain, was used as the specific probe for the spike receptor-binding domain (SP-RBD) protein as the target. The recognition between the two was measured by the change in the charge transfer resistance, determined by fitting the electrochemical impedance spectroscopy (EIS) spectra. The developed LSG-based biosensor achieved a linear detection range for the SP-RBD from 15 pM to 150 nM with a sensitivity of 0.0866 [log(M)]-1 and a limit of detection (LOD) of 7.68 pM.

The rapid, sensitive, and selective detection of pathogenic bacteria is of utmost importance in ensuring food safety and preventing the spread of infectious diseases. Here, we present a novel, reusable, and cost-effective impedimetric sensor based on a dual bacteria-imprinted polymer (DBIP) for the specific detection of Escherichia coli O157:H7 and Staphylococcus aureus. The DBIP sensor stands out with its remarkably short fabrication time of just 20 minutes, achieved through the efficient electro-polymerization of o-phenylenediamine monomer in the presence of dual bacterial templates, followed by in-situ template removal. The key structural feature of the DBIP sensor lies in the cavity-free imprinting sites, indicative of a thin layer of bacterial surface imprinting. This facilitates rapid rebinding of the target bacteria within a mere 15 minutes, while the sensing interface regenerates in just 10 minutes, enhancing the sensor's overall efficiency. A notable advantage of the DBIP sensor is its exceptional selectivity, capable of distinguishing the target bacteria from closely related bacterial strains, including different serotypes. Moreover, the sensor exhibits high sensitivity, showcasing a low detection limit of approximately 9 CFU mL-1. The sensor's reusability further enhances its cost-effectiveness, reducing the need for frequent sensor replacements. The practicality of the DBIP sensor was demonstrated in the analysis of real apple juice samples, yielding good recoveries. The integration of quick fabrication, high selectivity, rapid response, sensitivity, and reusability makes the DBIP sensor a promising solution for monitoring pathogenic bacteria, playing a crucial role in ensuring food safety and safeguarding public health.

We report a small footprint cost-effective isothermal rapid DNA amplification system, with integrated microfluidics for automated sample analysis and detection of SARS-CoV-2 in human and environmental samples. Our system measures low-level fluorescent signal in real-time during amplification, while maintaining the desired assay temperature, on a low power, portable system footprint. A unique soft microfluidic chip design was implemented to mitigate thermocapillary effects and facilitate optical alignment for automated image capture and signal analysis. The system-on-board prototype coupled with the LAMP primers designed by BioCoS, is sensitive enough to detect viral loads of SARS-CoV-2 in a broad concentration range corresponding to a threshold cycle range of 16 to 39. Clinical specimens were tested at Kingston Health Sciences using a clinically validated PCR assay and variants were determined using whole genome sequencing.

Fungal infection of grape berries (Vitis vinifera) by Botrytis cinerea frequently coincides with harvest, impacting both the yield and quality of grape and wine products. A rapid and non-destructive method for identifying B. cinerea infection in grapes at an early stage prior to harvest is critical to manage loss. In this study, zeolitic imidazolate framework-8 (ZIF-8) crystal was applied as an absorbent material for volatile extraction from B. cinerea-infected and healthy grapes in a vineyard followed by thermal desorption gas chromatography-mass spectrometry. The performance of ZIF-8 to absorb and trap targeted volatiles was evaluated with a standard solution of compounds and with a whole bunch of grapes enclosed in a glass container to maintain standard sampling conditions. Results from sampling methods were then correlated to B. cinerea infection in grapes as measured and determined by Genus specific antigen quantification. Trace levels of targeted compounds reported as markers of grape B. cinerea infection were successfully detected with in-field sampling. Peak area counts for volatiles 3-octanone, 1-octen-3-one, 3-octanol, and 1-octen-3-ol extracted using ZIF-8 were significantly higher than values achieved using Tenax®-TA from field testing and demonstrated good correlation with B. cinerea infection severities determined by B. cinerea antigen detection.

A unique two-column ²³⁰U/²²⁶Th generator has been developed. The focus was hold on obtaining ²²⁶Th of high purity in a solution amenable to further labeling. The first column of the proposed generator filled with TEVA Resin held ²³⁰U, from which ²²⁶Th was eluted with 7 M HCl solution. UTEVA Resin pretreated with nitric acid solution was used as a sorbent for the second column for thorium retention. ²²⁶Th was extracted with 0.01-0.05 M citric buffer solution. One cycle of generator milking took 5-7 minutes and produced > 90% of ²²⁶Th in 1.5 ml of eluate, pH 4.5-5.0. The proposed two-column ²³⁰U/²²⁶Th generator was tested over two months including a second loading of ²³⁰U additionally accumulated from ²³⁰Pa. The ²³⁰U impurity in ²²⁶Th eluate was less than 0.01% allowing to use it directly in synthesis of radiopharmaceutical compounds.

The disease COVID-19 is brought on by the acute respiratory syndrome coronavirus 2 (SARS-CoV-2) First appeared in China in December 2019 and quickly spread around the world after being declared a worldwide pandemic by the World Health Organization in March 2020. COVID-19, Medical Laboratory Professionals, SARS-COV-2, Diagnostic, Importance and difficulties for testing were the selected terms to search the databases of PubMed and Google Scholar for previously published material. Many diagnostic tests are applied in corona virus detection like Droplet Digital PCR (ddPCR), Multiplex PCR, Loop-mediated Isothermal Amplification (LAMP) and more. There is a lack of availability of molecular and serologic tests that have been clinically validated or authorized by national or international regulatory bodies. Clinical laboratory experts are tackling threats to our global defense and wellness, including infectious diseases. The opportunity to express gratitude to the unsung medical laboratory heroes and COVID0-19 pandemic allies is now greater than ever. Each year, Medical Laboratory Professionals Week should honors those who contribute key diagnostic data that help save lives. This review article explore overall summary on testing methods including Important and Difficult Tasks for Medical Laboratories which will provide good message for better public health matter.

The digital model of airborne frequency selective surface radomes (AFSSRs) is the basis of design, simulation analysis, manufacturing, and other related research of AFSSRs. This paper proposes a rapid modeling method of AFSSRs based on dynamic customizable primitives. Firstly, a layered digital model construction scheme of AFSSR is presented based on the typical radome wall structure. Then, according to the characteristics of various surface configurations and complex wireframe information of AFSSRs, the dynamic primitives are raised to express the boundary and contour information of all kinds of radomes. Focusing on the undevelopable characteristics of the aero-dynamic shape surface of the AFSSR, the arrangement solution and mapping method for frequency selective elements on undevelopable surfaces are proposed. Furthermore, the imple-mentation logic of this method on the creation of each layer model and the assembly of the whole machine model is introduced. Finally, according to this method, a rapid modeling system (RMS) is established, and the modeling effect and efficiency of the RMS are demonstrated and compared, which verifies the feasibility and effectiveness of this method.

The three-axis stabilization geostationary remote sensing satellite features high time resolution and plays a significant role in weather forecasting and environmental monitoring. With the future development of satellite technology, we propose a rapid geolocation algorithm for three-axis stabilization geostationary remote sensing satellites from the perspective of software algorithms. The method assesses conventional remote sensing data geolocation methods and the coordination group for meteorological satellites (CGMS, Coordination Group for Meteorological Satellites) nominal grid publishing format. First, the initial incident viewing vector of each detector on the sensor was constructed. Then, by reflecting the satellite platform's east-west and north-south mirrors, the outgoing vector of the payload coordinate system was obtained. This vector was converted to the satellite body coordinate system and, subsequently, to the satellite orbit coordinate system. The conversion of the earth-fixed coordinate system and the mirror rotation angle under ideal CGMS grid conditions were obtained, and the mirror rotation angle was converted to the corresponding CGMS nominal grid position to complete data positioning. The algorithm omits the complex process of calculating the intersection point between the viewing vector and the geodetic ellipsoid sphere from the earth-fixed coordinate system, resulting in an 83.3% improvement in computational efficiency without compromising positioning accuracy compared with conventional geolocation methods. This algorithm greatly improves the processing efficiency of geostationary meteorological satellite positioning, but its limitation is that the data processing results must be released in the CGMS nominal grid format.

Nerve agents have recently been used in battlefield operations, espionage wars and terrorist attacks. These compounds, like some pesticides, cause organophosphate poisoning. The rapid, non-contact detection of a sarin simulant has been demonstrated at the Diagnostics and Metrology Laboratory of the Italian National Agency for New Technologies, Energy and Sustainable Economic Development using laser photoacoustic spectroscopy, an infrared absorption technology. The first measurements, carried out with an experimental system based on a quantum cascade laser and developed for the assessment of food authenticity in the “fingerprint region”, show that a detection limit of 1 nanolitre is within the reach of the instrument when chemometric analysis is applied.

Geospatial knowledge in massive academic papers can provide knowledge services such as location-based research hotspot analysis, spatio-temporal data aggregation, research results recommendation, etc. However, geospatial knowledge often exists implicitly in literature resources in unstructured form, which is difficult to be directly accessed and mined and utilized for rapid production of massive thematic maps. In this paper, we take the geospatial knowledge of the area studied as an example and introduce its extraction method in detail. An integrated feature template matching and random forest classification algorithm is proposed for accurately identifying research areas from the abstract texts of academic papers and producing thematic maps. Firstly, the precise recognition of geographical names is achieved step by step based on BiLSTM-CRF algorithm and improved heuristic disambiguation method; then, the area studied is extracted by the designed integrated feature recognition template of area studied using random forest classification algorithm, and a fast thematic map is designed for the knowledge of area studied, topic and literature. The experimental results show that the area studied recognition accuracy can reach 97%, the F-value is 96%, and the recall rate reaches 96%, achieving high accuracy and high efficiency of area studied extraction in text. Based on the geospatial knowledge, the thematic map can achieve the effect of fast map formation and accurate expression.

Genetic adaptation of Hermetia illucens (BSF) to suboptimal single sourced wastes can open new perspectives for insect production. Here, four replicate BSF lines were maintained on a single sourced, low-quality wheat bran diet (WB) or on a high-quality chicken feed diet (CF) for 13 generations. We continuously evaluated evolutionary responses in several performance traits to rearing at the two diets. Subsequently, we tested responses to interchanged diets, i.e. of larvae that had been adapted to low-quality feed and to high quality feed and vice versa to evaluate costs associated with diet adaptation. BSF were found to experience rapid adaptation to the diet composition. While performances on WB diet were always inferior to CF diet, the adaptive re-sponses were stronger to the former diet. This stronger response was likely due to stronger se-lection pressure experienced by BSF fed on the low-quality single sourced diet. The interchanged diet experiment found no costs associated with diet adaptation but confirmed diet adaptation for the larval biomass and insect frass traits for the WB diet treatment. Our results revealed that BSF can rapidly adapt to diet through evolutionary responses, which has potential to be utilized to produce lines tailored to specific diets.

As environmental regulations become stricter, weight- and cost-effective fiber-reinforced polymer com-posites are being considered as alternative materials in the automobile industry. Rapid impregnation of the resin into the reinforcing fibers is critical during liquid composite molding, and the optimization of resin impregnation is related to the cycle time and quality of the products. In this review, various resins capable of rapid impregnation, including thermoset and thermoplastic resins, are discussed for manu-facturing fiber-reinforced composites used in the automobile industry, along with their advantages and disadvantages. Finally, vital factors and perspectives for developing rapidly impregnated resin-based fiber-reinforced composites for automobile applications are discussed

Food safety is a significant issue that affects people worldwide and is tied to their lives and health. The issue of pesticide residues in food is just one of many issues related to food safety, which leave residues in crops and are transferred through the food chain to human consumption. Foods contaminated with pesticide residues pose a serious risk to human health, including carcinogenicity, neurotoxicity and endocrine disruption. Although traditional methods including gas chromatography, high-performance liquid chromatography, chromatography and mass spectrometry can be used to achieve quantitative analysis of pesticide residues, the disadvantages of these techniques, such as being time-consuming and costly and requiring specialist staff, limit their application. Therefore, there is a need to develop rapid, effective and sensitive equipment for the quantitative analysis of pesticide residues in food. Microfluidics is rapidly emerging in a number of fields due to its outstanding strengths. This paper summarizes the application of microfluidic techniques to pyrethroid, carbamate, organochlorine and organophosphorus pesticides, as well as to commercial products. Meanwhile, the paper also outlines the development of microfluidics in combination with 3D printing technology and nanomaterials for the detection of pesticide residues in food.

Beta-carotene is a fat-soluble antioxidant commonly found in foods such as fruits, vegetables, and palm oil. Despite various liquid chromatography methods are proposed to detect and measure the sera carotenoid level, a long retention time to elute this marker is needed. This study attempted to develop a rapid reverse phase method in eluding beta-carotene in human sera. The researchers managed to elute the antioxidant in 2.2 minutes by applying a combination of a C8 column, mobile phase comprising of acetonitrile mixed with methanol in 70:30 proportion, and an ultra-high performance liquid chromatography system. The outputs had a good calibration curve (R²=0.959) and low coefficient of variation (0.2%), suggesting this protocol is reliable. A column with a lower carbon chain such as C8 allows the beta-carotene molecule to flow through the column faster. Besides, selecting solvents with high elution strength coupled with an ultra-high performance liquid chromatography system which equipped with high pressure can force the beta-carotene through the column in a shorter duration compared to previous reported methods. Therefore, it is recommended to adopt this protocol in epidemiological studies where beta-carotene is screened as a dietary biomarker associated with disease of interest by using human sera in the population level.

The oral health of older individuals can be negatively impacted by various systemic health factors, leading to rapid oral health deterioration. Older people are at risk of experiencing adverse reactions to medications due to multimorbidity, polypharmacy, and changes in pharmacokinetics and pharmacodynamics. Hyposalivation, a significant side effect of some medications, can be induced by both the type and number of medications used. Frailty, disability, sarcopenia, care dependency, and limited access to professional oral healthcare can also compromise the oral health of older people. To prevent rapid oral health deterioration, a comprehensive approach is required that involves effective communication between oral healthcare providers, other healthcare providers, and informal carers. Regardless of their health status, it is crucial to prioritize the well-being of older people. Oral healthcare providers have a responsibility to advocate for the importance of maintaining adequate oral health and to raise awareness of the serious consequences of weakened oral health. By doing so, we can prevent weakened oral health from becoming a geriatric syndrome.

Current commercial, pre-commercial, and experimental in ovo techniques for the sex determination of fertilised eggs employ either minimally invasive biomolecular assays (extracting fluid via a small laser-drilled window in the eggshell, for detection of genetic or hormonal biomarkers), analysis of volatile compounds emitted from the eggshell, visible imaging, and reflectance or transmission spectroscopic analysis exploiting molecular optical fluorescence, polarisation, and scattering phenomena, including various combinations of these modalities. , to date no endeavour employing the NIR and FTIR based spectroscopic techniques has resulted in a commercially sustainable solution to the egg sexing problem. Besides achieving only subpar performance in overall accuracy, specificity, and sensitivity, the least invasive of the current state-of-the-art optical methods still requires, creating a transmission window (fenestration) of 12–15 mm diameter through to the mammillae layer of the shell, proximal to the external shell membrane, which can affect the incubation or post-hatch development viability of up to 10% of incubated eggs. Multimodal solution combining Raman spectroscopy and hyperspectral imaging has strong prospects to overcome the hard barriers existing before the perfection of a non-invasive in-line process for high reliability and rapid throughput for sex determination of eggs within 3 days of incubation. The method for sexing of chicken embryos needs to take a multipronged approach in collecting and analyzing spectral data that points to biomarkers using the machine learning approaches to look for nanomolar to picomolar concentrations of these in the fluid.

The dynamic response of structural elements subjected to blast loading is a problem of growing interest in the field of defense and security. In this work, a novel computational tool for the rapid evaluation of the effects of explosions, hereafter referred as SimEx, is presented and discussed. The classical correlations for the reference chemical (1 kg of TNT) and nuclear (106 kg of TNT) explosions, both spherical and hemispherical, are used together with the blast wave scaling laws and the International Standard Atmosphere (ISA) model to compute the dynamic response of Single-Degree-of-Freedom (SDOF) systems subject to blast loading. The underlying simplifications in the analysis of the structural response follow the directives established by UFC 3-340-02 and the Protective Design Center Technical Reports of the US Army Corps of Engineers, which offer useful estimates with a low computational cost, enabling in particular the computation of damage diagrams in the Charge Weight-Standoff distance (CW-S) space for the rapid screening of component (or building) damage levels. SimEx is a computer application based on Matlab and developed by the Fluid Mechanics Research Group at University Carlos III of Madrid (UC3M), which has been successfully used for both teaching and research purposes in the Degree in Security Engineering, taught to the future Guardia Civil officers at the Spanish University Center of the Civil Guard (CUGC). This dual use has allowed the development of the application well beyond its initially objective, testing on one hand the implemented capacities by undergraduate cadets with end-user profile, and implementing new functionalities and utilities by Masters and PhD students. With this experience, the application has been continuously growing since its initial inception in 2014 both at a visual and a functional level, including new effects in the propagation of the blast waves, such as clearing and confinement, and incorporating new calculation assistants, such as those for the thermochemical analysis of explosive mixtures; crater formation; fragment mass distributions, ejection speeds and ballistic trajectories; and the statistical evaluation of damage to people due to overpressure, body projection, and fragment injuries.

The present work aims to characterize the mechanical behavior of a new composite material for the conservation and development of the vast historical and architectural heritage that is particularly vulnerable to environmental and seismic actions. The new composite consists of natural hydraulic lime (NHL) -based mortar, reinforced by sisal short fibers randomly oriented in the mortar matrix. The NHL-based mortar ensures the chemical-physical compatibility with the original feature of the historical masonry structures (mostly in stone and clay) aiming to pursue both the effectiveness and durability of the intervention. The use of vegetable fibers (i.e. the sisal one) is an exciting challenge for the construction industry since they require a lower degree of industrialization for their processing, and therefore, their costs are also low, as compared to the most common synthetic/metal fibers. Beams of sisal-composite sizing 160x40x40 mm3 with a central notch are tested in three-point bending, aiming to evaluate both their bending strength and fracture energy. Also, tensile tests and compressive tests were performed on the composite samples, while water retention test and slump test were performed on the fresh mix. Finally, the tensile tests on the Sisal strand were carried out to evaluate the tensile strength of both strand and wire. A final comparison with unreinforced mortar specimens shows that the proposed composite ensures great workability and good performances in term of ductility and strength and it can be considered a promising alternative to the classic fiber-reinforcing systems.

In recent years, the need to contain healthcare costs due to the growing public debt of many countries, combined with the need to reduce costly travel by patients unable to move autonomously, have captured the attention of public administrators towards tele-rehabilitation. This trend has been consolidated overwhelmingly following the Covid-19 pandemic, which has made it precarious, difficult and even dangerous for patients to access hospital facilities. We present a platform devoted to the rapid prototyping of Virtual Reality based, cognitive tele-rehabilitation exercises. Patients who experienced injury or pathology need to practice a continuous training in order to recover functional abilities, and the therapist need to monitor the outcomes of such practices. The Virtual Reality exercises are designed on Unity 3D to empower the therapist to set up personalised exercises in a easy way, enabling the patient to receive personalized stimuli, which are crucial for a positive outcome of the practice. Furthermore, the reaction speed of the system is of fundamental importance, as the temporal evolution of the scene must proceed parallel to the patient’s movements, to ensure an effective and efficient therapeutic response. So, we optimized the Virtual Reality application in order to make the loading phase and the startup phase as fast as possible and we have tested the results obtained with many devices: in particular computers and smartphones with different operating systems and hardware. The implemented platform integrates in Nu!Reha system®, a tele-rehabilitation set of services that helps patients to recover cognitive and functional capabilities.

Genome-scale engineering and custom synthetic genomes are reshaping the next generation of industrial yeast strains. The Cre-recombinase mediated chromosomal rearrangement mechanism of designer synthetic Saccharomyces cerevisiae chromosomes, known as SCRaMbLE, is a powerful tool which allows rapid genome evolution upon command. This system is able to generate millions of novel genomes with potential valuable phenotypes, but the excessive loss of essential genes often results in poor growth or even the death of cells with useful phenotypes. In this study we expanded the versatility of SCRaMbLE to industrial strains, and evaluated different control measures to optimise genomic rearrangement, whilst limiting cell death. To achieve this, we have developed RED (Rapid Evolution Detection), a simple colorimetric plate-assay procedure to rapidly quantify the degree of genomic rearrangements within a post-SCRaMbLE yeast population. RED-enabled semi-synthetic strains were mated with haploid progeny of industrial yeast strains to produce stress tolerant heterozygous diploid strains. Analysis of these heterozygous strains with the RED-assay, genome sequencing and custom bioinformatics scripts demonstrated a correlation between RED-assay frequencies and physical genomic rearrangements. Here we show that RED is a fast and effective method to evaluate optimal SCRaMbLE induction times of different Cre-recombinse expression systems for the development of industrial strains.

Several studies suggest that COVID-19 may be accompanied by symptoms such as a dry cough, muscle aches, sore throat, and mild to moderate respiratory illness. The symptoms of this disease indicate the fact that COVID-19 causes noticeable negative effects on the lungs. Therefore, considering the health status of the lungs using X-rays and CT scans of the chest can significantly help diagnose COVID-19 infection. Due to the fact that most of the methods that have been proposed to COVID-19 diagnose deal with the lengthy testing time and also might give more false positive and false negative results, this paper aims to review and implement artificial intelligence (AI) image-based diagnosis methods in order to detect coronavirus infection with zero or near to zero false positives and false negatives rates. Besides the already existing AI image-based medical diagnosis method for the other well-known disease, this study aims on finding the most accurate COVID-19 detection method among AI methods such as machine learning (ML) and artificial neural network (ANN), ensemble learning (EL) methods.

Objectives: To demonstrate the efficacy of Gemtuzumab ozogamicin in refractory AML patients with organ dysfunctions and poor performance status. Three refractory AML patients with are described. One of them was pretreated by intensive chemotherapy, two other patients progressed during Azacitidine treatment. WHO performance status III . Two patients had respiratory failure grade 2, the other one suffered from acute kidney insufficiency. Two patients were highly febrile with elevated CRP level. Gemtuzumab ozogamicin administration was performed in three patients followed by further switch to Gemtuzumab ozogamicin + Azacitidine or “7+3” treatment. Results: Gemtuzumab ozogamicin administration resulted in abrupt fever cessation in two febrile patients simultaneously with CRP level decrease and fast gradual resolution of respiratory failure. Recovery of kidney function was noticed in patient with renal insufficiency. WHO performance status have elevated in all three patients. No adverse effects grade II-III were noticed. Further treatment made two patients eligible for intensive chemotherapy, one patient was transplanted, patient with kidney failure obtained complete remission. Conclusions: Gemtuzumab ozogamicin therapy appeared to be safe and highly efficacious in relapsed/refractory AML patients with organ dysfunctions and poor performance status.

The food additive sorbic acid is considered as an effective preservative for certain cereal products, and propionic acid is commonly added in bakery wares, e.g. bread and fine bakery wares. The aim of this study is to develop and validate a new nuclear magnetic resonance spectroscopy (¹H NMR) method for routine screening and quantification of sorbic and propionic acids in bread and several bakery products for quality control purposes. Results showed that none of the screened samples contained higher concentrations than regulatory maximum limits. However, for some samples, labelling of preservatives was lacking or they were used in food categories, for which the use is not approved. It can be concluded that the developed NMR method can be used for routine screening of bakery products.

Poor therapeutic outcomes have been attributed to inter-individual and interethnic variability in cytochrome P450 (CYP450)-dependent metabolism and altered drug retention associated with P-glycoprotein (P-gp). An individualized pharmacotherapeutic approach would benefit the genetically diverse South African population. The study aim was to develop a validated, targeted, analytical method to quantify seven probe drugs and their metabolites in dried blood spots (DBS) using the Mitra™ volumetric absorptive micro-sampling device for blood collection. An Agilent liquid chromatography (LC) system coupled to a Sciex 4000 QTRAP tandem mass spectrometer (MS) was used for method optimization and validation. Targeted LC-MS/MS methods were validated according to ICH guidelines. The validated LC-MS/MS method met the required bioanalytical standards for specificity, sensitivity, linearity, accuracy, precision, carry-over, and stability. This study successfully validated the use of DBS, collected with the Mitra™ microsampling device, to measure expected probe drug and metabolite concentrations using the “Geneva phenotyping cocktail” for the purpose of simultaneous phenotyping of in vivo CYP450 metabolic activity of the CYP1A2, -2B6, -2C9, -2C19, -2D6, and -3A4 enzymes, and P-gp transport activity. However, statistical analysis using Bland-Altman plots showed that not all analytes exhibited linear distribution pharmacokinetics between DBS and plasma, which influenced the predicted vs real plasma concentrations based on measurements in a DBS matrix. These findings were attributed to the blood-to-plasma concentration ratio, the physicochemical properties and stability of the analytes, and the extraction efficiency of the Mitra™ sampler. More research is required before DBS sampling can be substituted for conventional plasma sampling

The goal of this study was to develop a rapid diagnostic kit for rheumatic disease and systemic lupus erythematosus (SLE) screening. A novel rapid vertical flow assay (VFA) was engineered and used to assay anti-nuclear (ANA) and anti-dsDNA (αDNA) autoantibodies from systemic lupus erythematosus (SLE) patients and healthy controls (HC). Observer scores and absolute signal intensities from the VFA were validated by ELISA. The rapid ten minute point of care VFA test engineered demonstrated a limit of detection of 0.5 IU/ml for ANA and αDNA autoantibodies in human plasma with inter-operator CV of 19% for ANA and 12% for αDNA. Storage stability was verified over a three-month period. When testing anti-dsDNA and ANA levels in 22 SLE and 18 HC serum samples, the duplex VFA revealed 95% sensitivity, 72% specificity and 84% accuracy in discriminating disease groups, comparable to the gold standard, ELISA. The rapid αDNA/ANA duplex VFA can potentially be used in primary care clinics for evaluating patients or at-risk subjects for rheumatic diseases and for planning follow-up testing. Given its low cost, ease and rapid turnaround, it can also be used to assess SLE prevalence estimates.

Abstract: A prevalence boundary (PB) marks the point in prevalence where the false omission rate, RFO=FN/(TN+FN), exceeds the tolerance limit for missed diagnoses. Objectives were to mathematically analyze rapid antigen test (RAgT) performance, determine why PBs are breeched, and evaluate the merits of testing three times over five days, now required by the US Food and Drug Administration for asymptomatic persons. Equations were derived to compare test performance patterns, calculate PBs, and perform recursive computations. An independent July 2023 FDA-university-commercial evaluation of RAgTs provided performance data used in theoretical calculations. Tiered sensitivity/specificity comprise: Tier-1) 90%, 95%; Tier-2) 95%, 97.5%; and Tier-3) 100%, ≥99%, respectively. Repeating a T2 test improves the PB from 44.6% to 95.2% (RFO 5%). In the FDA-university-commercial evaluation, RAgTs generated sensitivity of 34.4%, which improved to 55.3% when repeated, then 68.5% with the third test. With RFO=5%, PBs were 7.37/10.46/14.22%, respectively. PB analysis suggests RAgTs should achieve clinically proven sensitivity of 91.0-91.4%. When prevalence exceeds PBs, missed diagnoses can perpetuate virus transmission. Repeating low-sensitivity RAgTs delays diagnosis. In homes, high-risk settings, and hotspots, PB breaches may prolong contagion, defeat mitigation, facilitate new variants, and transform outbreaks into endemic disease. Molecular diagnostics can help avoid these potential vicious cycles