Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Background: First-line biological diagnosis of malaria in Mali is based on the use of rapid diagnostic tests (RDT), which detect in the blood the Histidin Rich Protein 2 antigen, specific to Plasmodium falciparum. Our study, based on a real-time polymerase chain reaction (qPCR) gold-standard diagnosis, aims to evaluate the performance of RDTs used in Mali and to describe the distribution of Plasmodium species in each administrative regions of Mali; Methods: We collected RDT cassettes in 47 sites of the nine regions of Mali. We randomly selected 150 malaria-negative and up to 30 malaria-positive RDTs from each regions. DNA was extracted from the RDTs’ nitrocellulose strip and then assayed with a pan-Plasmodium qPCR. Positive samples were then analyzed with qPCRs specific for P. falciparum, P. malariae, P. vivax, and P. ovale; Results: Of the 1,389 tested by qPCR RDTs, 258 (18.6%) were positive for Plasmodium spp. P.falciparum was the most predominant (97.3%). However, the prevalence of P.vivax reach 21.1% in the Ménaka region in the north; Conclusion: Overall, RDT diagnostic indices are adequate for the biological diagnosis of malaria in Mali. Our finding support the adjustment of RDTs to the local epidemiology.

The goal of this study was to develop a rapid diagnostic kit for rheumatic disease and systemic lupus erythematosus (SLE) screening. A novel rapid vertical flow assay (VFA) was engineered and used to assay anti-nuclear (ANA) and anti-dsDNA (αDNA) autoantibodies from systemic lupus erythematosus (SLE) patients and healthy controls (HC). Observer scores and absolute signal intensities from the VFA were validated by ELISA. The rapid ten minute point of care VFA test engineered demonstrated a limit of detection of 0.5 IU/ml for ANA and αDNA autoantibodies in human plasma with inter-operator CV of 19% for ANA and 12% for αDNA. Storage stability was verified over a three-month period. When testing anti-dsDNA and ANA levels in 22 SLE and 18 HC serum samples, the duplex VFA revealed 95% sensitivity, 72% specificity and 84% accuracy in discriminating disease groups, comparable to the gold standard, ELISA. The rapid αDNA/ANA duplex VFA can potentially be used in primary care clinics for evaluating patients or at-risk subjects for rheumatic diseases and for planning follow-up testing. Given its low cost, ease and rapid turnaround, it can also be used to assess SLE prevalence estimates.

Abstract: A prevalence boundary (PB) marks the point in prevalence where the false omission rate, RFO=FN/(TN+FN), exceeds the tolerance limit for missed diagnoses. Objectives were to mathematically analyze rapid antigen test (RAgT) performance, determine why PBs are breeched, and evaluate the merits of testing three times over five days, now required by the US Food and Drug Administration for asymptomatic persons. Equations were derived to compare test performance patterns, calculate PBs, and perform recursive computations. An independent July 2023 FDA-university-commercial evaluation of RAgTs provided performance data used in theoretical calculations. Tiered sensitivity/specificity comprise: Tier-1) 90%, 95%; Tier-2) 95%, 97.5%; and Tier-3) 100%, ≥99%, respectively. Repeating a T2 test improves the PB from 44.6% to 95.2% (RFO 5%). In the FDA-university-commercial evaluation, RAgTs generated sensitivity of 34.4%, which improved to 55.3% when repeated, then 68.5% with the third test. With RFO=5%, PBs were 7.37/10.46/14.22%, respectively. PB analysis suggests RAgTs should achieve clinically proven sensitivity of 91.0-91.4%. When prevalence exceeds PBs, missed diagnoses can perpetuate virus transmission. Repeating low-sensitivity RAgTs delays diagnosis. In homes, high-risk settings, and hotspots, PB breaches may prolong contagion, defeat mitigation, facilitate new variants, and transform outbreaks into endemic disease. Molecular diagnostics can help avoid these potential vicious cycles

Rapid antigen detection tests (RAD) are commonly used for the diagnosis of SARS-CoV-2 infections. However, with the continuous emergence of new variants of concern (VOC) presenting various mutations potentially affecting the nucleocapsid protein, the analytical performances of these assays should be frequently reevaluated. One-hundred and twenty samples were selected and tested with both RT-qPCR and five commercial RAD commonly sold in Belgian pharmacies. Of these, direct whole genome sequencing identified the strains present in 116 samples, of which 70 were Delta and 46 were Omicron. Sensitivity across a wide range of Ct values (13.5 to 35.7; median = 21.3) were comparable and ranged from 70.0% to 77.1% for Delta strains and from 69.6% to 78.3% for Omicron strains. When taking swabs with a low viral load (Ct > 25), poor performances were observed for the Delta strains (20.0 to 40.0%) and, even more so, for Omicron strains (0.0 to 23.1%). Two devices failed to detect all samples (n = 13) containing Omicron strains with a low viral load. The poor performance observed with low viral loads is an important limitation of RAD, which is not sufficiently highlighted in the instruction for use of these devices.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

The Xpert® Xpress SARS-CoV-2 and Xpert® Xpress SARS-CoV-2/Flu/RSV tests were rapidly developed and widely used during the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) pandemic. In response to emerging genetic variability, a new SARS-CoV-2 target (RNA-dependent RNA-polymerase) has been added to both tests: Xpert® Xpress CoV-2 plus and Xpert® Xpress CoV-2/Flu/RSV plus test. A rapid evaluation of both tests was performed in South Africa, using residual respiratory specimens. Residual respiratory specimens (n=125) were used to evaluate the Xpert® Xpress CoV-2 plus test and included 50 genotyped specimens. The Xpert® Xpress CoV-2/Flu/RSV plus test was assessed using 45 genotyped SARS-CoV-2 specimens, ten influenza A, ten Influenza B and twenty respiratory syncytial virus specimens. Results were com-pared to in-country standard of care tests. Genotyped specimens tested the performance of the test under pressure from circulating SARS-CoV-2 variants of concern. Reference material was included to assess the test limits and linearity. The Xpert® Xpress CoV-2 plus test performance compared to reference results across residual respiratory specimens was good (positive per-centage agreement (PPA)=95.2%, negative percentage agreement (NPA)=95.0%) The Xpert® Xpress CoV-2/Flu/RSV plus test showed good performance across all residual respiratory specimens (PPA=100%, NPA=98.3%). All genotyped variants of concern were detected by both tests. The Xpert® Xpress CoV-2 plus and Xpert® Xpress CoV-2/Flu/RSV plus tests can be used to diagnose SARS-CoV-2, and to diagnose and differentiate SARS-CoV-2, influenza A, influenza B and respiratory syncytial virus respectively. The NPA was lower than the recommended 99%, but was influenced by the low number of negative specimens tested. The variants of concern assessed did not affect test performance. It is recommended that sites perform their own assessments compared to in-country standard of care tests.

The performance of the presurgical test (preSurg) for temporal lobe epilepsy (TLE) was evaluated via video-electroencephalography (VEEG), electroencephalography (EEG), 99mTc-HmPAO single-photon emission tomography (SPECT) and 1.5 T magnetic resonance imaging (MRI) in a group of 112 men (37.0 ± 1.1 years) and 106 women (39.7 ± 1.1 years) operated on for TLE. The epileptic zone (EZ) was adequately identified to determine whether the patient reached an Engel I grade (EI) at least one year postop. Accuracy was evaluated by the coefficient α, ranging from 3 (when result = EZ) to 2 (result in the same hemisphere as the EZ), 1 (noninformative result) or 0 (EZ in the contralateral hemisphere). The simplicity of diagnosis was defined as the number of preSurg surgeries needed to identify the EZ. EI was obtained in 85.8% of patients even though 42.2% of patients had noninformative MRI results. For preSurg α was (mean ± SEM) = VEEG (2.83 ± 0.04) > MRI (2.14 ± 0.08) > EEG (1.87 ± 0.09) > SPECT (1.71 ± 0.09). The accuracy (combination of sensitivity and specificity) was calculated as follows: VEEG (0.797) > MRI (0.518) > EEG (0.446) > SPECT (0.360). The likelihood positive ratio was greater, and the likelihood negative ratio was lower for VEEG. The most relevant factor for the regression model was VEEG (3.106) > MRI (2.558) > EEG (1.905), and the factors were not significantly related to SPECT. EZs in EI patients with low simplicity were identified mainly by VEEG. A very good postoperative outcome can be obtained even in TLE patients with no lesions on MRI. The VEEG is the most reliable preSurg test and may be the only reliable test for patients with very low simplicity (i.e., difficult).single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

1) Background: Northwest Syria (NWS), is a conflict-affected and unstable area. Due to its limited health infrastructure, accessing advanced COVID-19 testing services is challenging. COVID-19 antigen rapid diagnostic tests (Ag-RDTs) have the potential to overcome this barrier. Therefore, a pilot project was implemented to introduce Ag-RDTs in this setting aiming to a) describe the feasibility, uptake, and results of Ag-RDTs; and b) identify facilitators and barriers to Ag-RDTs testing. 2) Methods: A cross-sectional study design involving secondary analysis of data collected during the project’s monitoring was developed. A local NGO implemented 25,000 Ag-RDTs cross boarder through trained community health workers. 3) Results: A total of 27,888 persons were found eligible and enrolled, of which 24,956 (89.5%) consented to test and 121 (0.5%) were found positive. Highest positivity was observed among those with severe COVID-19 symptoms (12.7%), those with respiratory illnesses (2.5%), persons enrolled at Afrin Hospitals (2.5%), and healthcare workers (1.9%). A non-random sample of 236 people underwent confirmatory rt-PCR test. Accordingly, observed sensitivity, specificity, positive and negative predictive values, were 80.0%, 96.1%, 91.4% and 90.3%, respectively. Key encountered challenges included obtaining informed consent and conducting confirmatory rt-PCR testing. 4) Conclusion: This project demonstrated great feasibility utilizing Ag-RDTs as a screening/diagnostic tool for COVID-19 infections with nearly 90% uptake. Considering the high specificity and negative predictive values and the higher positivity rates among severe COVID-19 symptomatic, embedding Ag-RDTs into COVID-19 testing strategies for ruling out and in COVID-19 infections would hold a great advantage.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

In this paper, we study the asymptotic behavior of the sequential empirical process and the sequential empirical copula process, both constructed from residuals of multivariate stochastic volatility models. Applications for the detection of structural changes and specification tests of the distribution of innovations are discussed. It is also shown that if the stochastic volatility matrices are diagonal, which is the case if the univariate time series are estimated separately instead of being jointly estimated, then the empirical copula process behaves as if the innovations were observed; a remarkable property. As a by-product, one also obtains the asymptotic behavior of rank-based measures of dependence applied to residuals of these time series models.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

Structures inevitably suffer damages after an earthquake, with their severity ranging from minimal damages to non-structural elements to partial or even total collapse, possibly with loss of human lives. Thus, it is essential for engineers to understand the crucial factors that drive a structure towards suffering higher degrees of damage, so that preventative measures can be taken. In the present study, we focus on three well-known damage thresholds, namely Collapse Limit State, Ultimate Limit State and Serviceability Limit State and analyze which of the features obtained via Rapid Visual Screening, determine whether or not a given structure will cross that threshold. To this end, we use Machine Learning to perform binary classification for each damage threshold, as well as Explainability via SHAP values (acronym for SHapley Additive exPlanations) to quantify the effect of each parameter. The quantitative results obtained demonstrate the potential applicability of ML methods to re-calibrate the computation of structural vulnerability indices using data from recent earthquakes.

Preschoolers with disabilities and their caregivers have been neglected in health and social service provision in most low-income countries and arguably too in low resourced areas of more affluent nations. Yet as this rapid review of published literature identifies, there are low-cost, evidence-based strategies to address their needs that can be implemented in communities by local people. Five key features of the necessary supports are examined. First the leadership functions required to create and implement the support services. Second, the family-centred, home-based support provided to caregivers and the personnel undertaking this form of support. Third, providing opportunities for peer support to flourish and encouraging the formation of advocacy groups across families. Fourth, mobilizing the support of significant groups within the community; notably traditional healers and leaders; health services and poverty alleviation initiatives. Fifth, devising ways in which preschool educational opportunities can be offered to children as a prelude to their inclusion in primary schools. The review serves a further purpose. It provides an example of how public health researchers and academics could achieve more rapid implementation of evidence-based knowledge into existing and new support services through dissemination to community practitioners.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

New antimicrobial approaches are essential to counter antimicrobial resistance. The drug development pipeline is exhausted with emergence of resistance resulting in unsuccessful trials. The lack of an effective drug developed from the conventional drug portfolio has mandated the introspection into the list of potentially effective unconventional alternate antimicrobial molecules. Alternate therapies, that are clinically explicable forms include monoclonal antibodies, antimicrobial peptides, aptamers and phages. Clinical diagnostics optimizes the drug delivery. In the era of diagnostic-based applications, it is logical to draw diagnostic based treatment for infectious diseases. Selection criteria of alternate therapeutics in infectious disease include detection, monitoring of response and resistance mechanism identification. Integrating these diagnostic applications is disruptive to the traditional therapeutic development. The challenges and mitigation methods need to be noted. Applying the goals of clinical pharmacokinetics that include enhancing efficacy and decreasing toxicity of drug therapy this review analyses the strong correlation of alternate antimicrobial therapeutics in infectious diseases. The relationship between drug concentration and the resulting effect defined by the pharmacodynamic parameters are also analyzed. This review analyzes the perspectives of aligning diagnostic initiatives into the use of alternate therapeutics with a particular focus on companion diagnostic applications in infectious diseases.

Respiratory infections constitute a major reason for infants and children seeking medical advice and visiting health facilities, thus remaining a significant public threat with high morbidity and mortality. The predominant viruses causing viral respiratory infections are influenza A and B viruses (Flu-A, Flu-B), Respiratory Syncytial Virus (RSV), Adenovirus and Coronaviruses. We aimed to record the incidence of RSV, SARS-CoV-2, Influenza A/B and Adenovirus cases with rapid antigen tests and validate the results with RT-PCR assay of upper respiratory specimens with a wide range of viral loads and (co)-infection patterns in children. Clinical samples were collected from early symptomatic children (presenting with fever and/or cough and/or headache within 5–7 days). The surveillance program was conducted in five private pediatrician dispensaries and one Pediatric care unit, from 10 January 2023 to 30 March 2023 in central Greece. The total sample of specimens collected was 784 young children and infants, of which 383 (48.8%) ware female and 401 were male (51.2%). The mean age of participants was 7.3 + 5.5 years. The sensitivity of FLU A & B test was 91.15% (95% CI: 84.33% -95.67%), and the specificity was 98.96% (95% CI: 97.86% - 99.58%). The sensitivity and specificity of the adenovirus and RSV test was {92.45% (95% CI: 81.79% - 97.91%), 99.32% (95% CI: 98.41% -99.78%)} and {92.59% (95% CI: 75.71% -99.09%), 99.47% (95% CI: 98.65% - 99.86%)} respectively. Lastly, the sensitivity of the SARS-CoV-2 test was 100.00% (95% CI: 79.41%-100.00%) and the specificity was 99.74% (95% CI: 99.06% - 99.97%). We recorded proportion of incidence for the Influenza-A and B, (14.3%), - (3.44%) correspondingly, followed by the adenovirus with a proportion (6.9%) and the RSV with (3.7%) incidence proportion and finally, the SARS-CoV-2 (2.3%). The combination of a new multiple rapid test with multiple antigens, will be probably a useful tool with financial impact for health systems targeting the early detection and right treatment of respiratory infections in the emergency departments in primary health care facilities.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Background. Amyotrophic Lateral Sclerosis (ALS) is a devastating disease involving motor neuron degeneration. The few drugs approved for treatment have at most a marginal benefit, and death usually occurs 2-5 years after diagnosis. Methods. A thorough manual examination of the relevant literature, covering over 35,000 papers. Results. Two major phenomena that are generally not known to clinicians were found. First, insulin signaling is impaired in ALS even in patients not diagnosed with diabetes (DB). Almost all studies that have explicitly tested insulin function in non-DB ALS patients using glucose tolerance tests (18 out of 20, 1964-2022, different groups) have found it to be impaired. Second, there is strong evidence for excessive insulin-independent glucose uptake (IIGU) in ALS. In addition, (i) early/late diabetes are associated with increased/decreased risk, respectively; (ii) insulin-based diabetes drugs are protective in ALS in large retrospective human studies; and (iii) strong animal and human evidence shows that insulin opposes all of the major pathological processes in ALS. Conclusion. Most ALS patients have insulin impairment, yet this is commonly not diagnosed, likely because excessive IIGU normalizes glucose levels. The impairment promotes disease progression. Late diabetes is associated with decreased risk because high glucose levels indicate non-excessive IIGU, and because diabetes drugs are protective. Insulin-based treatment (e.g., GLP1 agonists, insulin) is beneficial and can be disease-modifying in ALS and in frontotemporal dementia variants comorbid with ALS. ALS patients should be routinely tested for insulin function and treated if test results are positive.

The main foundations of the standard $\Lambda $CDM model of cosmology are that: 1) The redshifts of the galaxies are due to the expansion of the Universe plus peculiar motions; 2) The cosmic microwave background radiation and its anisotropies derive from the high energy primordial Universe when matter and radiation became decoupled; 3) The abundance pattern of the light elements is explained in terms of primordial nucleosynthesis; and 4) The formation and evolution of galaxies can be explained only in terms of gravitation within a inflation+dark matter+dark energy scenario. Numerous tests have been carried out on these ideas and, although the standard model works pretty well in fitting many observations, there are also many data that present apparent caveats to be understood with it. In this paper, I offer a review of these tests and problems, as well as some examples of alternative models.

Augmented and Virtual Reality have been experiencing a rapidly growth in recent years, but there is not still a deep knowledge on their capabilities and where they could be explored. In that sense, this paper presents a study on the accuracy and repeatability of the Microsoft's HoloLens 2 (Augmented Reality device) and HTC Vive (Virtual Reality device) using an OptiTrack system as ground truth. For the HoloLens 2, the method used was hand tracking, while in HTC Vive, the object tracked was the system's hand controller. A series of tests in different scenarios and situations were performed to explore what could influence the measures. The HTC Vive obtained results in the millimetre scale, while the HoloLens 2 revealed not so accurate measures (around 2 centimetres). Although the difference can seem to be considerable, the fact that HoloLens 2 was tracking the user's hand and not an inherit controller made a huge impact. The results were considered a significant step for the on going project of developing a human-robot interface to program by demonstration an industrial robot using Extended Reality, which shows great potential to succeed based on this data.

An extensive review of literature simulations of polymer melts is given, considering results that test aspects of the Rouse model in the melt. We focus on the mean-square amplitudes < (X_p(0))^{2} > and time correlation functions < X_p(0) X_p(t) > of the Rouse modes $X_p(t)$. Contrary to the Rouse model: (i) Mean-square Rouse mode amplitudes < (X_p(0))^2> do not scale as sin^{-2}(p \pi/2N), N being the number of beads in the polymer. For small p (say, p <= 3) < (X_p(0))^2> scales with p as p^{-2}$; for larger p it scales as p^{-3}. (ii) Rouse mode time correlation functions < X_p(t) X_p(0) > do not decay with time as exponentials; they instead decay as stretched exponentials exp(-a t^b)$. b depends on p, typically with a minimum near N/2 or N/4. (iii) Polymer bead displacements are not described by independent Gaussian random processes. (iv) For p not equal to q, < X_p(t) X_{q}(0) > is sometimes non-zero. (v) The response of a polymer coil to a shear flow is a rotation, not the affine deformation predicted by Rouse. Simulations thus conclusively demonstrate that the Rouse model is invalid in polymer melts. We also briefly consider the Kirkwood-Riseman polymer model.

Alzheimer's disease (AD) detection acting as an essential role in global health care due to misdiagnosis and sharing many clinical sets with other types of dementia, and costly monitoring the progression of the disease over time by magnetic reasoning imaging (MRI) with consideration of human error in manual reading. This paper goal a comparative study on the performance of data mining techniques on two datasets of Clinical and Neuroimaging Tests with AD. Our proposed model in the first stage, Apply clinical medical dataset to a composite hybrid feature selection (CHFS), for extract new features to select the best features due to eliminating obscures features, In parallel with Apply a novel hybrid feature extraction of three batch edge detection algorithm and texture from MRI images dataset and optimized with fuzzy 64-bin histogram. In the second stage, we applied a clinical dataset to a stacked hybrid classification(SHC) model to combine Jrip and random forest classifiers with six model evaluations as meta-classifier individually to improve the prediction of clinical diagnosis. At the same stage of improving the classification accuracy of neuroimaging (MRI) dataset images by applying a convolution neural network (CNN) in comparison with traditional classifiers, running on extracted features from images. The authors have collected the clinical dataset of 426 subjects with (1229 potential patient sample) from oasis.org and (MRI) dataset from a benchmark kaggle.com with a total of around ~5000 images each segregated into the severity of Alzheimer's. The datasets evaluated using an explorer set of weka data mining software for the analysis purpose. The experimental show that the proposed model of ‏(CHFS) feature extraction ‏ lead to effectively reduced the false-negative rate with a relatively high overall accuracy with a stack hybrid classification of support vector machine (SVM) as meta-classifier of 96.50% compared to 68.83% of the previous result on a clinical dataset, Besides a compared model of CNN classification on MRI images dataset of 80.21%. The results showed the superiority of our CHFS model in predicting Alzheimer's disease more accurately with the clinical medical dataset in early-stage compared with the neuroimaging (MRI) dataset. The results of the proposed model were able to predict with accurately classify Alzheimer's clinical samples at a low cost in comparison with the MRI-CNN images model at the early stage and get a good indicator for high classification rate for MRI images when applying our proposed model of SHC.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

The paper presents construction, laboratory tests as well as the first field application of a new fiber-optic rotational seismograph. The system based on fiber-optic gyroscope (FOG) with determined Angle Random Walk of the order of 10-8 rad/Sqrt(s) and a few rad/s maximum detectable amplitude of rotation in the frequency range from DC to 328.12 Hz. It has been designed for rotational seismology area of interest. This work also presents exemplary relevant measurements which were conducted using a set of two devices installed in the geophysical observatory in Książ, Poland.

In this review, we present the latest exclusion limits obtained with astroparticles for Lorentz Invariance Violation (LIV) in the photon sector. We discuss the techniques known as energy-dependent time delay or time lag, subluminal pair production threshold shift, superluminal photon decays and superluminal photon splitting. Perspectives for future results in LIV with the next generation of experiments are also addressed.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

The energy E takes the place of the gravitational mass m_G to produce gravity [1]. We wonder whether the inertial mass m_i in the inertial force is also replaced by E. The experiments to measure the inertial force and weight of a carrier are presented. Now we can test the principle of equivalence and study foundations of physics in condensed matter.

Statistical inferences is regarded as the general criteria for statistical conclusion and drawing generalizations. However, most of the inferential statistical tools are based on strong assumptions which create a strict limitations on their use and application. Analysis of variance (ANOVA) is one of such statistics. In this article, eight (8) new ANOVA-like methodologies were proposed, in alternative to one-way ANOVA, based on the assumptions of statistical mirroring. Methods validation in comparison with one-way ANOVA was designed to assess the suitability and statistical power of the new proposals as an alternative methods, using different sets of logically generated multivariate datasets with different problems and statistical complications. The results of comparisons validate that the eight (8) proposed ANOVA-like methodologies were suitable alternatives to ANOVA, in the sense that they require no normality assumption to be meet, used different ways to compare the data with different statistical elements rather than depending on only variance, efficient with negative values, and results interpretation is easier.

The Medi-test system we developed was motivated by the large number of resources available for the medical domain, as well as the number of tests needed in this field (during and after the medical school) for evaluation, promotion, certification, etc. Generating questions to support learning and user interactivity has been an interesting and dynamic topic in NLP since the availability of e-book curricula and e-learning platforms. Current e-learning platforms offer increased support for student evaluation, with an emphasis in exploiting automation in both test generation and evaluation. In this context, our system is able to evaluate a student’s academic performance for the medical domain. Using as input medical reference texts and supported by a specially designed medical ontology, Medi-test generates different types of questionnaires for Romanian language. The evaluation includes 4 types of questions (multiple-choice, fill in the blanks, true/false and match), can have customizable length and difficulty and can be automatically graded. A recent extension of our system also allows for the generation of tests which include images. We evaluated our system with a local testing team, but also with a set of medicine students, and user satisfaction questionnaires showed that the system can be used to enhance learning.

Ground penetrating radar (georadar, GPR), widely used in geology, archeology and road construction, is an efficient tool for searching and studying subsurface objects and structures. When planning GPR missions, it is necessary to predict the resolution of the device and the achievable probing depth. The article discusses the methods and results of assessing these characteristics of the Loza-V and Loza-N radars obtained in the course of archaeological and geographical expedition works.

Background and objectives: The fact that the results of troponin and Nt-proBNP interfere from biotin caused some commercial firms to update their measurement methods. In particular, the clinical incompatibility of cardiac test results may affect the risk of morbidity and mortality. The aim of this study is to investigate the interference effects of 7 different contrast agents on cardiac markers (Troponin-I, Nt-proBNP, Mass CK-MB, CK, AST, LDH) and coagulation tests (PT, APTT). Materials and Methods: Seven different contrast medias were added into control materials by using interference protocol. Concentration of PT, APTT, CK, AST, LDH, Mass CK-MB, Troponin-I, Nt-proBNP were measured by Sysmex CS-2100, Abbott c16000, Siemens Centaur XP and AFİAS-6 analyzer. The amount of deviations from target values were calculated. Results: 7 different contrast medias caused negative interference in troponin levels between 57.43% and 62.87%. It was found that different contrast medias produced false negativity in the Nt-proBNP test ranging from 6.11% to 96.01%. Enzymes and coagulation tests have been less affected. Conclusions: Different contrast medias may cause false negative cTnI and Nt-proBNP. Therefore, the contrast medias which causes the least interference should be preferred. The results of samples taken in the first hour of contrast imaging should be interpreted with care.

Various designs of spherical robots using barycenter offset mechanisms were previously reported. This kind of robots offers advantages such as turning in placeor moving in any direction at any time. Yet, the approaches resulting in a balanced robot, which could roll with reduced energy costs once accelerated, are scarce. We introduce anovel robot of this type. The feasibility of the approach is verified on a cylindrical robot. This paper presents an open-source, remotely controlled, robotic cylinder. The robot uses a specifically designed mechanism to displace a mass in its center, which causes the cylinder to roll forwards or backwards. The movement characteristics of the cylinder, as well as the mathematical and physical limitations of the mechanism were studied. An intuitive user interface allows the robot to be controlled through WiFi. This robot was manufactured only with readily available and inexpensive materials, which would make it a suitable platform for education, typically in the fields of physics and engineering.

A numerical mechanism connecting ice algal ecodynamics with the buildup of organic macromolecules is tested within modeled pan-Arctic brine channels. The simulations take place offline in a reduced representation of sea ice geochemistry. Physical driver quantities derive from the global sea ice code CICE, including snow cover, thickness and internal temperature. The framework is averaged over ten boreal biogeographic zones. Computed nutrient-light-salt limited algal growth supports grazing, mortality and carbon flow. Vertical transport is diffusive but responds to pore structure. Simulated bottom layer chlorophyll maxima are reasonable, though delayed by about a month relative to observations due to uncertainties in snow variability. Upper level biota arise intermittently during flooding events. Macromolecular concentrations are tracked as proxy proteins, polysaccharides, lipids and refractory humics. The fresh biopolymers undergo succession and removal by bacteria. Baseline organics enter solely through cell disruption, so that the internal carbon content is initially biased low. By including exudation, agreement with dissolved organic or individual biopolymer data is achieved given strong release coupled to light intensity. Detrital carbon then reaches hundreds of micromolar, sufficient to support structural changes to the ice matrix.

The importance of sleep for healthy brain function is widely acknowledged. However, it remains unclear how the internal generation of dreams might facilitate cognitive processes. In this perspective we review a computational approach inspired by artificial intelligence that proposes a framework for how dreams occurring during rapid-eye-movement (REM) sleep can contribute to learning and creativity. In this framework, REM dreams are characterized by an adversarial process that, against the dream reality, tell a discriminator network to classify the internally created sensory activity as real. Such an adversarial dreaming process is shown to facilitate the emergence of real-world semantic representations in higher cortical areas. We further discuss the potential contributions of adversarial dreaming beyond learning, such as balancing fantastic and realistic dream elements, and facilitating the occurrence of creative insights. We characterize non-REM (NREM) dreams, where a single hippocampal memory is replayed at a time, as serving a complementary role of improving the robustness of cortical representations to environmental perturbations. We finally explain how subjects can become aware of the adversarial REM dreams, but less of the NREM dreams, and how the awareness phenomenon of wake, dream and lucid dreaming may appear.

The electrical motor design requires a lot of work and resources. In the field, motor designers need to decide on competitive motor sizing quickly to compete with other motor suppliers. Generally, it requires expensive FEM S/W to get accurate motor sizing results, but buying and maintaining many licenses is costly. Moreover, it needs some patience to get the result from FEM analysis. In this paper, the motor sizing technique using an existing production motor is presented to respond to urgent requests from customers without using FEM analysis. In order to enhance the fidelity of the result, magnetic flux loss by magnet coating and non-linear characteristics are considered during the motor sizing process. The proposed sizing method was verified by comparison to the FEM analysis and test result and showed reasonable confidence in them. Also, this method has the substantial advantage of outputting accurate results instantly without taking any time. It helps with the modification design of electrical motors without using expensive FEM S/W and a certain level of skill or experience.

In only a few months after initial discovery in Wuhan, China, SARS-CoV-2 and the associated COVID-19 disease has become a global pandemic causing significant mortality and morbidity. In the absence of vaccines and effective therapeutics, reliable serological testing can be a key element of public health policy to control further spread of the disease and gradually ease quarantine measures. However, prior to launch of large-scale seroprevalence studies to assess herd immunity, it is critical to understand the limits and potential of current SARS-CoV-2 serological tests on the market. In this study, we provide an overview of serological testing and conduct a systematic review of independent evaluations of SARS-CoV-2 serological tests performance. Our findings show significant variability in the accuracy of marketed tests and highlight several lab-based and point-of-care rapid diagnostic tests with high performance level in detecting SRAS-CoV-2 specific antibodies. The findings of this review highlight the need for ongoing independent evaluations of commercialized COVID-19 diagnostic tests.

In social & health sciences, many statistical procedures and estimation techniques rely on the underlying distributional assumption of normality of the data. Non-normality may lead to incorrect statistical inferences. This study evaluates the performance of selected normality tests on the stringency framework for the skewed alternative space. Stringency concept allows us to rank the tests uniquely. Bonett & Seier test (T_w) turns out to be the best statistics for slightly skewed alternatives and the Anderson-Darling (AD), Chen-Shapiro (CS), Shapiro-Wilk (W) and Bispo, Marques, & Pestana, (BCMR) statistics are the best choices for moderately skewed alternative distributions. Maximum loss of Jarque-Bera (JB) and its robust form (RJB), in terms of deviations from the power envelope, is greater than 50% even for large sample sizes which makes them less attractive in testing the hypothesis of normality against the moderately skewed alternatives. On balance, all selected normality tests except T_w and COIN performed exceptionally well against the highly skewed alternative space.

To date, various chimeric lysins have been developed as efficacious antibiotics against multidrug-resistant bacteria, but direct comparisons of their antibacterial activities have been difficult due to the preparation of multiple recombinant chimeric lysins. Previously, we reported an E. coli cell-free expression method to screen better chimeric lysins against Staphylococcus aureus, but we still needed to increase the amounts of expressed proteins enough to be able to detect them non-isotopically for quantity comparisons. In this study, we improved the previous cell-free expression system by adding a previously reported artificial T7 terminator and reversing the different nucleotides between the T7 promoter and start codon to those of the T7 phage. The new method increased the expressed amount of chimeric lysins enough for us to detect them using Western blotting. Therefore, the qualitative comparison of activity between different chimeric lysins has become possible via the adjustment of the amount variables between samples without protein purification. We applied it to select more active chimeric lysins derived from our previously reported chimeric lysin (ALS2). Finally, we compared the antibacterial activities of our selected chimeric lysins with reported chimeric lysins (ClyC and ClyO) and lysostaphin, and determined the rank orders of antibacterial activities on different S. aureus strains in our experimental conditions.

In this contribution we present work on rapid thermal annealing of as-electrodeposited thin films of Cu2ZnSnS4. The treatment was carried out in cold wall tubular reactor in dynamic conditions with variations of temperature, speed and time of the specific elements of the process. The effect of annealing was investigated by X-ray diffractometry, Raman scattering and Scanning Electron Microscopy (SEM). The phase composition of the films in dependence on conditions of treatment was analysed and have been shown that in slow and prolonged high-temperature process the low temperature binaries react completely and only Kesterite and ZnS is left. In addition, structural investigations by XRD have shown gradual decrease of crystallite sizes when the temperature level and duration of the high-temperature segment increases and respectively increase in the strain, due to formation of the phases in non-equilibrium conditions. In opposite, when the speed of dynamic segments in the process decreases the both crystallite size and strain of the Kesterite decreases non-monotonically. The grain sizes of Kesterite, presented by SEM investigations, have shown increase when the temperature and the duration increase, respectively the speed decreases with exemption at higher temperature near 750 C. The set of experiments gave idea by scrupulous analysis of Raman data to elucidate the track for fine manipulating of the defects in the structure of CZTS thin films having in mind the dependences of the ratios of Q = I287/I303 and Q’= I338/(I366+I374) on the process variables.

Road segment can be estimated from GPS trajectories by averaging. However, most existing averaging strategies suffer from high complexity or poor accuracy. For example, finding the optimal mean for a set of sequences is known to be NP-hard, while using Medoid compromises the quality. In this paper, we introduce three extremely fast and practical methods for solving the problem. The methods first analyze three descriptors and then use either a simple linear model or a more complex curvy model depending on an angle criterion. The results outperform Medoid and provide equal or better accuracy than the best existing methods while being very fast, and therefore suitable for real-time processing.

Background: Study to assess glucose levels of people with type 1 diabetes (T1D) overnight based on insulin type and timing. Methods: Real-world, retrospective study in T1D using multiple daily insulin injections. Contin-uous glucose monitoring and insulin injections data were collected for ten hours after dinner us-ing the Insulclock® connected cap. Meal events were identified using ROC detection methodology. The timing of rapid insulin, second injections, and the type of insulin analogs used were evaluat-ed. Results: Nocturnal profiles (n=775, 49 subjects) were analyzed. Higher glucose AUC over 180mg/dL was observed in delayed injections (number; %; mg/dL x h): -45-15min (n=136; 17.5%, 175.9 ±271.0); -15-0min (n= 231; 29.8%, 164.0 ±237.1); 0+45min (n= 408; 52.6%, 203.6 ±260.9), (p 0.049). The use of ultrarapid (FiAsp®) (URI) vs rapid insulin analogs (RI) was associated with less hypoglycemia events (7.1 vs 13.6%; p 0.005) and TBR70 (1.7 +6.9 vs 4.6 +13.9%; p 0.003). Us-ers of glargine U300 vs degludec had higher TIR (70.7 vs 58.5 %) (Adjusted R-squared: 0.22, p < 0.001). The use of a correction injection (n= 144, 18.6%) was associated with higher hypoglycemia events (18.1 vs 9.5%; p 0.003), TBR70 (5.5 +14.2 vs 3.0 +11.1%; p 0.003), glucose AUC over 180 mg/dL (226.1 +257.8 vs 178.0 +255.3 mg/dL x h; p 0.001), and lower TIR (56.0 +27.4 vs 62.7 +29.6 mg/dL x h; p 0.004). Conclusions: Dinner rapid insulin timing, insulin types and correction injections affect nocturnal glucose profile in T1D.

Verification of inclusivity of molecular detection methods gives indications on the reliability of viral infections diagnosis because of the tendency of viral pathogens to undergo sequence variation. This study was aimed to select inclusive probe based reverse transcription quantitative PCR (RT-qPCR) assays for the diagnosis of the most widespread and detrimental viruses infecting honeybees, namely the acute bee paralysis virus (ABPV), the black queen cell virus (BQCV), the chronic paralysis bee virus (CBPV), the deformed wing virus variants A (DWVA) and B (DWVB), and the sacbrood virus (SBV). Therefore, detection methods previously described were re-evaluated in silico for specificity and inclusivity. Based on this evaluation, selected methods were modified or new ones were designed and tested in duplex RT-qPCR reactions. The limits of detection (LODs), effect of multiplexing on sensitivity and viral RNA quantification potential in bees and hive debris were assessed. This study made available diagnostic assays able to detect an increased number of virus variants compared to previously described tests and two viral pathogens in a single PCR reaction.

Abstract: Development of the fast neutron radiography with higher penetration capability in Non-Destructive Testing (NDT) techniques is rapidly. The detection efficiency and the imaging spatial resolution are the main problem of the radiography detector for many fast neutron imaging systems. In this paper, a detector composed of pixelated EJ200 scintillator array，an 16 × 16 silicon-photomultipliers (SiPM) array, and a capacitive multiplexing network readout electronics is designed. Using Monte-Carlo simulations，the main parameters of the detector was optimization. Then the detector prototype was fabricated and tested at a 14 MeV D-T neutron source. The preliminary test results showed that the prototype has spatial resolution of 1.26 mm. Using pixelated scintillator structure，the conflict between spatial resolution and detect efficiency could improved. Moreover, SiPMs offer a flexibility for the expansion of application field of the imaging system due to their excellent photon detection performance, relatively low price and joint possibility for large area.

COVID-19, caused by the SARS-CoV-2 virus, has spread around the world and killed around 6.9 million people. Rapid and accurate diagnosis is essential for preventing and controlling the disease, reducing transmission and consequently saving lives. RT-PCR is the gold standard test used to detect the disease. However, the test is expensive and the result is time-consuming, which makes mass testing difficult, especially in countries with limited resources. In addition, the test has high analytical specificity and low diagnostic sensitivity, which leads to false-negative results. Several studies in the literature report the presence of hematological and biochemical alterations in infected patients and use these alterations with machine learning algorithms to help diagnose the disease. Therefore, this article presents the results obtained by different neural network architectures based on Adaptive Resonance Theory (ART) for the diagnosis of COVID-19. The study was conducted in two distinct stages: the first consisted of selecting the best ART network among several, using three open-access datasets and comparing the results with the literature. In the second stage, the chosen model was tested on a dataset containing patients from various hospitals in four countries. In addition, the model was subjected to external validation, including data from a country not present during the training and adjustment of the model, in order to validate the robustness and generalization capacity of the model. The results obtained by the ART networks in this study are promising, outperforming not only classical models, but also the deep learning models often used in the literature. Validation on data from different countries strengthens the model’s reliability and effectiveness.

Digital Image Correlation (DIC) is an optical technique used to measure surface displacements and strains in materials and structures. This technique has demonstrated significant utility in structural examination and monitoring. This manuscript offers a comprehensive review of contemporary research and applications that have leveraged the DIC technique in laboratory-based structural tests. The reviewed works encompass a broad spectrum of structural components, such as concrete beams, columns, pillars, masonry walls, infills, composite materials, structural joints, steel beams, slabs, and other structural elements. These investigations have underscored the efficacy of DIC as a metrological instrument for precise quantification of surface deformation and strain in these structural components. Moreover, the constraints of the DIC technique have been highlighted, especially in scenarios involving extensive or complex test configurations. Notwithstanding these constraints, the DIC methodology has validated its effectiveness as a strain measurement instrument, offering numerous benefits such as non-invasive operation, full-field measurement capability, high precision, real-time surveillance, and compatibility with integration into other measurement instruments and methodologies.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Brucellosis is one of the most common etiologies of laboratory-acquired infections worldwide, and handling of living brucellae should be performed in a Class II biological safety cabinet. The low infecting dose, multiple portals of entry to the body, the great variety of potentially contaminated specimens, and the unspecific clinical manifestations of human infections facilitate the unintentional transmission of brucellae to laboratory personnel. Work accidents such as spillage of culture media cause only a small minority of exposures, whereas >80% of events result from unfamiliarity with the phenotypic features of the genus, misidentification of isolates, and unsafe laboratory practices such as aerosolization of bacteria and working on an open bench without protective goggles or gloves. Although the bacteriological diagnosis of brucellae by traditional methods is simple, the Gram stain and the biochemical profile of the organism, as determined by commercial kits, can be misleading, resulting in inadvertent exposure and contagion. The use of novel identification technologies is not hazard-free. The MALDI-TOF technology requires an initial bacterial inactivation step, while the instruments’ reference database may misidentify Brucella as belonging to other Gram-negative species. The rapid identification by the FISH method mistakes brucellar isolates for members of the closely related Ochrobactrum genus.

An experimental series of shearing tests with water infiltration were performed on compacted unsaturated soil to simulate the behavior of shallow slope failures. Soil samples were compacted at moisture contents from dry to wet of optimum moisture content with the degree of saturation varying from 24.0% to 59.5% while maintaining the degree of compaction at 80%. Two series of shearing with infiltration tests were performed in this study. In Series-I, just before the start of shearing, matric suction was decreased by increasing pore water pressure to start water infiltration i.e. shearing is carried simultaneously with water infiltration. In Series-II, the soil was first sheared with drained pore air and undrained pore water to pre-defined value of deviatoric stress, after which matric suction was decreased by increasing pore water pressure to start water infiltration and shearing is performed by keeping deviatoric stress constant on the specimen. The test results showed that the decrease in matric suction has an effect on the volume of infiltrated water and degree of saturation. The soil slopes compacted on the dry side of optimum moisture content showed better performance than other soils, they require more decrease in matric suction to start water infiltration and showed higher deviatoric stress. In addition to this, water infiltration alone can cause the failure of shallow slopes without having to have any further loading.

World health is increasingly threatened by the growing number of spice-related food hazards. Further development of reliable methods for rapid, non-targeted identification of counterfeit ingredients within the supply chain is needed. ENEA has developed a portable, user-friendly photoacoustic laser system for food fraud detection, based on a quantum cascade laser and multivariate calibration. Following a study on the authenticity of saffron, the instrument was challenged with a more elusive adulterant, olive leaves in oregano. The results show that the reported method of laser sensing and chemometric analysis was able to detect adulterants at mass ratios of at least 20% in less than five minutes.

Real estate has the dual characteristics of consumption and investment. Under the inherent concept of "where there is land, there is wealth", real estate has become the investment target of the main asset. In addition to the supply and demand of the market will affect the price of real estate, many general economic factors will also have a certain impact on the price of real estate. This paper pays a special focus on the effects of MRT on housing prices, finding the closer a house is to an MRT station, the higher its price. In addition, convenience stores are very popularized, and this research report is also interested in whether the number of convenience stores within walking distance will affect the house price. In a word, these two factors do affect housing prices significantly.

This study aims to investigate a friction stir welded joint between steel and aluminum alloy. Friction stir welding is nowadays one of the most interesting joining technique due to the possibility to connect materials and thicknesses that are difficult or impossible to weld with traditional techniques. The main advantage is that Materials are not affected by thermal cycle problems during solidification and cooling and the absence of fumes and pollution during the process favors the quality of the welded joint. The life of metal joints could be greatly reduced in a corrosive environment, since the less noble material will tend to increase its corrosion rate while the nobler one will reduce its electrochemical dissolution. Accelerated ageing tests (i.e. salt fog test) are used to estimate the lifetime of metal joints in highly aggressive environments. The aim of the present work is to evaluate the durability at long ageing time in salt spray test (according to ASTM B117) of carbon steel/aluminum alloy joints, obtained by FSW. In this first part, mechanical tests results are reported. A deep metallographic and chemical investigation are going to be reported in the part 2.

The increasing prevalence of Metabolic Syndrome (MetS), a serious condition associated with elevated risks of cardiovascular diseases, stroke, and type 2 diabetes, underscores the urgent need for effective diagnostic tools. This research carefully examines the effectiveness of 16 diverse machine learning (ML) models in predicting MetS, a multifaceted health condition linked to increased risks of heart disease and other serious health complications. Utilizing a comprehensive, unpublished dataset of imbalanced blood test results, spanning from 2017 to 2022, from the Laboratory Information System of the General Hospital of Amfissa, Greece, our study embarks on a novel approach to enhance MetS diagnosis. By harnessing the power of advanced ML techniques, we aim to predict MetS with greater accuracy using non-invasive blood test data, thereby reducing the reliance on more invasive diagnostic methods. Central to our methodology is the application of the Borda count method, an innovative technique employed to refine the dataset. This process prioritizes the most relevant variables, as determined by the performance of the leading ML models, ensuring a more focused and effective analysis. Our selection of models, encompassing a wide array of ML techniques, allows for a comprehensive comparison of their individual predictive capabilities in identifying MetS. This study not only illuminates the unique strengths of each ML model in predicting MetS but also reveals the expansive potential of these methods in the broader landscape of health diagnostics. The insights gleaned from our analysis are pivotal in shaping more efficient strategies for the management and prevention of Metabolic Syndrome, thereby addressing a significant concern in public health.

In this paper, we propose a method for the generation of simulation test scenarios for autonomous driving. Based on the requirements of standard regulatory test scenarios, we can generate virtual simulation scenarios and functional scenario libraries for autonomous driving, which can be used for simulation verification of different ADAS functions. Firstly, the design operation domain (ODD) of the functional scenario is selected and the weight values of the ODD elements taken are calculated; then a combination test algorithm based on parameter weights is improved to generate autonomous driving virtual simulation test cases for the ODD elements, which can effectively reduce the number of generated test cases compared with the traditional combination test algorithm; then the traffic participant elements under each test case are Then, the values of the subelements under the traffic participant element in each test case are sampled and clustered to obtain hazard specific scenarios. Finally, the specific scenarios are applied to the automatic emergency braking (AEB) system on the model-in-the-loop (MIL) testbed to verify the effectiveness of this scenario generation method.

Measurements of systems taken along a continuous functional dimension, such as time or space, are ubiquitous in many fields, from the physical and biological sciences to economics and engineering. Such measurements can be viewed as realisations of an underlying smooth process sampled over the continuum. However, traditional methods for independence testing and causal learning are not directly applicable to such data, as they do not take into account the dependence along the functional dimension. By using specifically designed kernels, we introduce statistical tests for bivariate, joint, and conditional independence for functional variables. Our method not only extends the applicability to functional data of the Hilbert-Schmidt independence criterion (HSIC) and its d-variate version (d-HSIC), but also allows us to introduce a test for conditional independence by defining a novel statistic for the conditional permutation test (CPT) based on the Hilbert-Schmidt conditional independence criterion (HSCIC), with optimised regularisation strength estimated through an evaluation rejection rate. Our empirical results of the size and power of these tests on synthetic functional data show good performance, and we then exemplify their application to several constraint- and regression-based causal structure learning problems, including both synthetic examples and real socio-economic data.

Consumers often cite cognitive improvements as reasons for making dietary changes or using dietary supplements, a motivation that if leveraged could greatly enhance public health. However, rarely is it considered whether standardized cognitive tests that are used in nutrition research are aligned to outcomes of interest to the consumer. This knowledge gap presents a challenge to the scientific substantiation of nutrition-based cognitive health benefits. Here we combined qualitative consumer research and expert group methodology to (1) understand how consumers comprehend the potential benefits of nutrition for brain health, and (2) determine the alignment between consumers' articulated brain benefits and validated tests and tools. We derived a ‘Consumer Taxonomy of Cognitive and Affective Health in Nutrition Research’ which describes the cognitive and affective structure from the consumers' perspective. Experts agreed that validated tests exist for some consumer benefits including focused attention, sustained attention, episodic memory, energy levels, and anxiety. Prospective memory, flow, and presence represented novel benefits that require the development and validation of new tests and tools. Closing the gap between science and consumers, and fostering co-creative approaches to nutrition research, are critical to the development of products and dietary recommendations that support realizable cognitive benefits that benefit public health.

Flammability was evaluated and the results showed the values of critical flux at extinguishment (CFE) as 49.5kW/㎡ on average, total heat release (Qt) as 0.21MJ on average, and peak heat release rate (Qp) as 0.66kW on average, which satisfied all of the thresholds presented by the IMO. Therefore, flame-retardant plywood, of which the flame-retardant performance was evaluated, was determined to be an applicable finishing material that satisfies fire safety standards.

The consumption of dairy products and the dairy industry is one of the main global agro-food sectors for size, economic importance and level of technology. Microbiological quality of pasteurized milk or other milk products is dependent on microbiological quality of raw milk. A variety of microbiological count methods is available for monitoring the hygienic quality of raw milk. Among them, the pour plate method is the official essay for counting the number of colony forming units in milk samples according to ISO 4833-1:2013. The aim of the present study is the validation of the Micro Biological Survey (MBS) method, against the reference plate count method, for the assessment of the microbiological quality of raw milk. This comparative study, performed in collaboration with the “Istituto Zooprofilattico Sperimentale del Lazio e della Toscana M. Aleandri” (IZSLT), demonstrates the accuracy of this alternative method for the determination of total viable bacterial count in cow’s raw milk. The results obtained with the MBS method highlighting its potential as a valid tool for reliable microbiological analysis in dairy industries.

In this paper, PEN3 electronic nose was used to detect and recognize fresh and moldy apples (inoculated with Penicillium expansum and Aspergillusniger) taken Golden Delicious apples as model subject. Firstly, the apples were divided into two groups: apples only inoculated with different molds (Group A) and mixed apples of inoculated apples with fresh apples (Group B). Then the characteristic gas sensors of the PEN3 electronic nose that were most closely correlated with the flavor information of the moldy apples were optimized and determined, which can simplify the analysis process and improve the accuracy of results. Four pattern recognition methods, including linear discriminant analysis (LDA), backpropagation neural network (BPNN), support vector machines (SVM) and radial basis function neural network (RBFNN), were then applied to analyze the data obtained from the characteristic sensors, respectively, aiming at establishing the prediction model of flavor information and fresh/moldy apples. The results showed that only the gas sensors of W1S, W2S, W5S, W1W and W2W in the PEN3 electronic nose exhibited strong signal response to the flavor information, indicating were most closely correlated with the characteristic flavor of apples and thus the data obtained from these characteristic sensors was used for modeling. The results of the four pattern recognition methods showed that BPNN presented the best prediction performance for the training and validation sets for both the Group A and Group B, with prediction accuracies of 96.29% and 90.00% (Group A), 77.70% and 72.00% (Group B), respectively. Therefore, it first demonstrated that PEN3 electronic nose can not only effectively detect and recognize the fresh and moldy apples, but also can distinguish apples inoculated with different molds.

Globally, over the past several months millions of persons contracted the coronavirus disease 2019 (COVID-19) resulting in significant mortality. Health care systems are negatively impacted including the care of individuals with cancers and other chronic diseases such as chronic active hepatitis, cirrhosis and hepatocellular carcinoma. There are various probable pathogenic mechanisms that have been presented to account for liver injury in COVID-19 patients such as hepatotoxicity cause by therapeutic drugs, severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection of the bile duct cells and hepatocytes, hypoxia and systemic inflammatory response. Liver biochemistry tests such as AST, ALT, GGT and ALP are deranged in COVID-19 patients with liver injury. Hepatocellular damage results in the elevation of serum AST and ALT levels in early onset disease while a cholestatic pattern that develops as the disease progress causes higher levels of ALP, GGT, direct and total bilirubin. These liver biochemistry tests are prognostic markers of disease severity and should be carefully monitored in COVID-19 patients. We conducted a systematic review of abnormal liver biochemistry tests in COVID-19 and the possible pathogenesis involved. Significant findings regarding the severity, hepatocellular pattern, incidence and related clinical outcomes in COVID-19 patients are highlighted.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

The two-parameter distribution introduced by Kumaraswamy (1980) is a very flexible alternative to the Beta distribution with the same (0,1) support. Originally proposed in the field of hydrology, it has subsequently received a good deal of positive attention in both the theoretical and applied statistics literatures. Interestingly, the problem of testing formally for the appropriateness of the Kumaraswamy distribution appears to have received little or no attention to date. To fill this gap, in this paper we apply the “biased transformation” methodology proposed by Raschke (2009) to several standard goodness-of-fit tests based on the empirical distribution function. A simulation study reveals that these (modified) tests perform well in the context of the Kumaraswamy distribution, in terms of both low size distortion, and respectable power. In particular, the “biased transformation” Anderson-Darling test dominates the other tests that are considered.

Given that evaluating suspected child maltreatment is a challenging task, we aimed to begin to explore how laboratory test results may assist in its detection. Hence, we have examined biomarker differences between 137 children entering out-of-home care and 126 children living in their own homes. Each child entering Majorcan institutionalized care was randomly matched for gender and age with children living in their homes and the same health area. Concerning basic hematological and biochemical values, children placed in out-of-home care differed significantly from children remaining at home in four distinct ways. Children at care entry had significantly higher eosinophil counts than children at home; and also had significantly lower levels of transaminase, thyroid-stimulating hormone, triglycerides and LDL-Cholesterol than children living at home. Oxidative stress linked to anxiety disorders and underweight are common features found in children at entry into the care system. The present study shows a relationship between some underweight or oxidative stress biomarkers and the risk of entry into out-of-home care. Medical diagnoses require physicians to select and assemble relevant data from all available information. Accordingly, we should consider the implementation of laboratory checkups in order to identify the abused from the non-abused child better.

Carbapenemase-producing organisms (CPOs) present a major threat to public health, demanding precise diagnostic techniques their detection. Discrepancies among CPO tests have raised concerns, partly due to limitations in detecting bacterial diversity within host/specimen. We explored the impact of unbiased colony selection on carbapenemase testing and assessed its relevance on various tests. Based on "FirstAll" for unbiased colony selection to reduce bias, we compared modified carbapenem inactivation method/EDTA-modified carbapenem inactivation method (mCIM/eCIM), Carba5, the CPO panel, and multiplex PCR (M-PCR). Initially, we compared FirstAll to conventional colony selection for mCIM. Second, we used M-PCR as a reference, to evaluate test performance across seven CPO species. The results revealed that FirstAll selection improved carbapenemase detection, revising false-negative in 10.5% of K. pneumoniae isolates. In addition, 12.4% of CPOs tested positive for multiple carbapenemase genes. Both the Carba5 test and CPO panel showed suboptimal performance (sensitivity/specificity: Carba5 75.5%/89.0%, CPO panel 78.1%/74.0%). Carba5 test provided specific carbapenemase class assignments but CPO panel failed in 20.3% of cases. Carba5 test and the CPO panel results correlated well with ceftazidime-avibactam minimal inhibitory concentrations (MICs). Concordance for class A/D with MICs was 88.3% for Carba5 and 92.0% for the CPO panel; whereas for class B, it was 86.5% for Carba5 and 76.2% for the CPO panel. In conclusion, FirstAll as the unbiased colony selection impacted carbapenemase testing. With FirstAll, the diagnostic performance of either Carba5 or the CPO panel was compromised. The utilization of ceftazidime-avibactam guided by either the CPO panel or Carba5 was appropriate.

Most diagnostic tests for tuberculosis (TB) rely on sputum samples, which are difficult to obtain and have low sensitivity in immunocompromised patients, patients with disseminated TB, and children, delaying treatment initiation. The World Health Organization (WHO) calls for the development of a rapid, biomarker-based, non-sputum test capable of detecting all forms of TB at the point-of-care to enable immediate treatment initiation. Lipoarabinomannan (LAM) is the only WHO-endorsed TB biomarker which can be detected in urine, an easily collected sample. This review discusses the characteristics of LAM as a biomarker, describes the performance of first-generation urine LAM tests and reasons for slow uptake, and presents considerations for developing the next-generation of more sensitive and impactful tests. Next-generation urine LAM tests have the potential to reach adult and pediatric patients regardless of HIV status or site of infection and facilitate global TB control. Implementation and scale-up of existing LAM tests and development of next-generation assays should be prioritized.

Purpose: National Institute for Health and Care Excellence (NICE) has recently published quality standards for assessment of fall risk and preventing further falls. According to the standards, multifactorial fall risk assessments should include: identification of falls history; analysis of gait, balance, mobility and muscle strength, among other factors. Despite being based on subjective analysis or simple timing and not being multifactorial, physiotherapists and physicians quite often use these tests as reference scales to differentiate between lower and higher risk of falling. Instrumented TUG has been recently reported to provide important additional information to the overall score. Objective: To explore a case-based approach of fall risk assessment to identify the most relevant and informative risk factors that in combination could better define a person risk profile. Materials and Methods: A multifactorial assessment of fall risk through questionnaires, standard functional tests, tests instrumented with inertial sensors, and force platforms has been studied within a group aged 55-80 years old. Different fall risk factors and fall risk assessment methods were analyzed in a case-based descriptive study. Results & Discussion: Subjects at higher risk of falling were identified based on their detailed profiles. A set of features were obtained from the instrumented standard tests differing significantly between subjects presenting higher or lower fall risk. Therefore, instrumenting conventional tests with wearables containing inertial sensors and force platforms gives more detailed and quantitative insights. This information can be used to better define and tailor fall prevention exercises and to improve the follow-up of the evolution of the subject.

Contemporary global policy, driven by concern for the environment, imposes increasingly stringent goals for reducing CO2 emissions. Therefore, there is an urgent need to develop effective models that allow an accurate prediction of CO2 emissions from vehicles powered by alternative fuels such as CNG. This article presents the process of creating one of the first models of CO2 emission for a vehicle powered by CNG. Emission modelling is based on data obtained from chassis dynamometer tests and road tests using the portable emission measurement system (PEMS). CO2 emission modelling was conducted in Python programming language using the Optuna framework for the XGBoost technique. The models obtained were validated, with indicators R2 0.9 and RMSE 0.49 for data from chassis dynamometer tests, and R2 0.7, RMSE 0.71 for road test data. This work has the potential to be used by transportation decision makers involved in environmental analyses and policymaking for urban areas.

Increasing evidence supports the direct healing effects of forests, partly attributed to the exposure to plant-emitted monoterpenes available in the forest atmosphere. The potential benefits on respiratory functions from inhaling monoterpenes have gained attention, especially due to the global rise in respiratory diseases. This study involved 42 asthmatic adolescents attending a summer rehabilitation camp at an Altitude Pediatric Asthma Center within a densely forested area in the Eastern Italian Alps. Volatile organic compound measurements indicated a pristine atmosphere, enabling modeling of continuous hourly monoterpenes concentration. Monoterpene concentration exposure and total inhaled dose were assessed over a 14-day stay, during which spirometry, lung oscillometry, and fractional exhaled nitric oxide were measured. Statistically significant correlations were observed between modifications in lung function parameters among asthmatic adolescents and monoterpenes exposure. These findings suggest a potential localized airway effect specific to monoterpenes. This pilot cohort study might pave the way for further investigations into the therapeutic effects of forest monoterpenes on lung function tests, asthma, and the broader healing potential of forest environments.

The coronavirus disease (COVID-19) is a respiratory tract infection caused by the new virus SARS-CoV-2. In March 2020, the World Health Organization (WHO) declared a worldwide COVID-19 pandemic. Since then, there has been a rush to find preventative or curative treatment. This arrived with the appearance of the COVID-19 vaccine, months after the declaration of the pandemic. In the setting of global COVID-19 immunization, there have been reports of rare skin immune-mediated diseases (IMD) after COVID-19 vaccination, particularly systemic sclerosis. Systemic sclerosis (SSc) is the most reported new onset IMD following messenger RNA (mRNA) COVID-19 vaccination. The pathogenesis of SSc is not fully understood, and the diagnosis is based on clinical symptoms. We report a 54-year-old male, with no prior history of autoimmune disorder, with rapid and progressive skin thickening (Modified Rodnan skin score 30/51), weeks after his mRNA COVID-19 vaccination. Antinuclear antibodies (ANA) showed a strongly positive nuclear fine-speckled pattern, but no SSc autoantibodies were found. The patient was diagnosed with SSc based on the persistence of autoantibodies and the clinical criteria according to the 2013 American College of Rheumatology/European League Against Rheumatism classification. Due to the proximity of the two events, we hypothesized a cross-reaction between COVID-19 vaccination and, in genetically predisposed patients, an emergence of systemic sclerosis. Our case suggests a potential relationship between the mRNA COVID-19 vaccine and new-onset autoimmune diseases. Physicians should be aware of this possible association.

Earthquake is among the most devastating natural disasters causing severe economic, environmental, and social destruction. Earthquake safety assessment and building hazard monitoring can highly contribute to urban sustainable development through identification and insight into optimum materials and structures. While the vulnerability of structures mainly depends on the structural resistance, the safety assessment of buildings can be highly challenging. In this paper, we consider Rapid Visual Screening (RVS) method which is a qualitative procedure for estimating structural scores for buildings suitable for medium- to high-seismic cases. This paper presents an overview of the common RVS methods, i.e., FEMA P-154, IITK-GGSDMA, and EMPI. To examine the accuracy and validation, a practical comparison is performed between their assessment and observed damage of reinforced concrete buildings from a street survey in the Bingöl region, Turkey, after the 11 May 2003 earthquake. The results demonstrate that the application of RVS methods for preliminary damage estimation is a vital tool. Furthermore, the comparative analysis showed that FEMA P-154 creates an assessment that overestimates damage states and is not economically viable while EMPI and IITK-GGSDMA provide for more accurate and practical estimation, respectively.

The importance of detecting bacteria in various food products is ever-increasing, due to recent food trends that lend themselves to food contamination. Additionally, the detection of probiotics in food products is of increasing importance to consumers, who realize the benefits of probiotics on one’s diet. Existing technologies for detection of bacteria in food are accurate, but most are slow, increasingly costly and unsuitable for applications outside of research laboratories. Optic approaches have recently emerged as an alternative, allowing rapid detection of bacterial presence. This study employs a portable kinetics fluorometer, fabricated in-house, in conjunction with NADH sensitive fluorescence reporter for analysis of various food products. The presence of bacteria is detected in 5 minutes. Both pathogenic and probiotic bacteria were detected in food products, such as raw chicken and beef, spoiled lettuce and contaminated water, yogurt, and kombucha tea. The cellular activity of two probiotic pills was also verified. All samples displayed varying levels of bacterial activity. The study indicates the viability of biosensors being used as an alternate method to detect bacteria in food products – and the viability of a fluorescence-based biosensor to detect viable bacteria. The approach is suitable for both laboratory and field determinations.

The moisture content of maize seed is an important indicator for evaluating seed quality and a fundamental item in grain testing. The experiment used direct drying method to measure the moisture content of 80 different varieties of maize samples, and captured their images using a hyperspectral imaging (HSI) system in the spectral range of 1100~2498nm. By comparing seven spectral preprocessing methods, the PLSR model established after Normalize pretreatment had the best effect. The characteristic wavelengths were selected by Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS) and Uninformative Variable Elimination (UVE). Twelve prediction models were established for full band spectra and characteristic wavelengths based on PLSR, PCR and SVM. By comparing the performance of the prediction models, it was found the Normalize-SPA-PLSR algorithm was optimized. The values of RC2 and RP2 in the model were higher, which were 0.9936 and 0.9933, respectively, while the values of RMSEP and RMSECV were lower, which were 0.0357 and 0.0380, respectively. The Normalize-SPA-PLSR model was used as a visual prediction model for moisture content of maize seed, the 20 maize varieties in the prediction set were visualized to obtain visualized color images of moisture content. The color differences between different moisture content images were significant. The result indicated that hyperspectral imaging could accurately, rapidly, and non-destructive predict moisture content of maize seed, which provided technical support for moisture content detection in the process of maize harvest, storage and processing.

Positive Health (PH) has been described as a promising transformative innovation to address the challenges of promoting well-being and reducing the burden of disease. The aim of this study is to review the current state of knowledge about PH as introduced by Huber et al. (2016) within the available scientific literature. A rapid review of the literature following the Cochrane Rapid Review recommendations. Three databases were searched (PubMed, Google Scholar, and CINAHL). Data were extracted and synthesized using a narrative approach. A total of 55 articles were included. Initial evaluation studies reveal promising results both at individual and collective levels. However, a need is expressed in several articles for further refinement of the conceptualization of PH and ways to make the effects of the PH approach more measurable. Professionals also expressed a desire for a more informed application and elaboration of the PH method across various settings and populations to enhance its effectiveness in practice. This rapid review highlights the transformative potential of PH in shifting from a disease-focused to a health-oriented paradigm of healthcare. It underscores the need for continued research regarding further development of the concept and its practical method, along with the necessity for methodological innovation.

Despite the increasing popularity of liquid chromatography-mass spectrometry (LC-MS)-based lipidomics, there is a lack of accepted and validated method for lipid extract quality and quantity assessment prior to LC-MS. Fourier-Transform Infrared Spectroscopy (FTIR) has been reported for quantification of pure lipids, however, the sample complexity and purity complex lipid extract quantification in lipidomics experiments could be impact quantification accuracy. Here, we report comprehensive assessment of the sample matrix on the accuracy of lipid quantification using Attenuated Total Reflectance Fourier-Transform Infrared Spectroscopy (ATR-FTIR). Pure lipids are characterized by CH-and C=O-stretching vibrations on FTIR, with quantitative range of 40–3000 ng and a limit of detection of 12 ng. Sample extraction method and local baseline subtraction during FTIR spectral processing significantly impact lipid quantification by CH-stretching. To facilitate sample quality screening, we developed the Lipid Quality (LiQ) score from a spectral library of common contaminants, using a ratio of peak heights between CH-stretching vibrations maxima and the collective vibrations from amide/amine, CH-stretching minima and sugar moieties. We evaluated LiQ score as a rapid sample quality control method by comparing to total LC-MS intensity of targeted lipidomics of 107 human plasma lipid extracts. Exclusion of poor-quality samples based on LiQ score improved the correlation between FTIR and LC-MS quantification. Finally, the uncertainty of absolute quantification by FTIR was estimated using a 795 ng SPLASH LipidoMix standard to be &lt;10%. In summary, this study identified key parameters for accurate FTIR-based quantification of complex lipid mixture, and developed a rapid workflow requiring only 1 µL of MS-ready sample and &lt; 5 minutes for routine lipidomics sample quality and quantity assessment.

Biosensors have shown great potential in realizing rapid, low cost and portable on-site detection for diseases. This work reports the development of a new bioelectronic sensor called AC electrokinetics-based capacitive (ABC) biosensor, for the detection of genomic DNA (gDNA) of methicillin-resistant Staphylococcus aureus (MRSA). The ABC sensor is based on interdigitated microelectrodes biofunctionalized with oligonucleotide probes. It uses a special AC signal for direct capacitive monitoring of topological change on nanostructured sensor surface, which simultaneously induce dieletrophoretic enrichment of target gDNAs. As a result, rapid and specific detection of gDNA/probe hybridization can be realized with high sensitivity. It requires no signal amplification such as labelling, hybridization chain reaction, or nucleic acid sequence-based amplification. This method involves only simple sample preparation. After optimization of nano-structured sensor surface and signal processing, the ABC sensor demonstrated fast turnaround of results (~10 s detection), excellent sensitivity (a detection limit of 4.7 DNA copies /µL MRSA gDNA) and high specificity, suitable for point of care diagnosis. As a bioelectronic sensor, the developed ABC sensors can be easily adapted for detection of other infectious agents.

Electrode is a key component in a microbial electrolysis cell (MEC) and it needs significant improvement for practical implementation of MEC. For effective development of electrode technology, accurate and reproducible analytical methods are very important. Linear sweep voltammetry (LSV) is an essential analytical method for evaluating electrode performance; however, it has not been firmly established yet in the MEC field. In this study, biological brush (BB), abiotic brush (AB), Pt wire (PtW), stainless steel wire (SSW) and mesh (SSM)) were tested to explore the most suitable counter electrode in different medium conditions. Coefficient of variation (CV) for Imax of LSV were comparatively analyzed. In BB-anode LSV, SSW (0.48%) and SSM (2.17%) showed higher reproducibility as a counter electrode. In SSM-cathode LSV, BB (1.76%) and PtW (2.01%) produced more reproducible results. In the Ni-AC-SSM-cathode LSV, PtW (3.54%) and BB (8.81%) produced more reproducible result. It shows electrode used in the operation is an appropriate counter electrode in the acetate-added condition. However, in the absence of acetate, PtW (1.24%) and BB (1.71%) produced more reproducible results in SSM cathode and PtW (0.61%) and SSW (1.21%) did in the Ni-AC-SSM-cathode, showing PtW is an appropriate counter electrode. These results also shows that PtW is an appropriate counter electrode in cathode LSV.

Current oncological developments are based on improved understanding of genetics, and especially the discovery of genes whose alterations affect cell functions with consequences for the whole body. Our work is focused on the one of these genes, the BARD1 and its oncogenic role in breast cancer. Most importantly, the study points to new avenues in the treatment and prevention of the most frequent female cancer based on BARD1 research. The BARD1 and BRCA1 proteins have similar structures and functions, and they combine to form the new molecule BARD1-BRCA1 heterodimer. The BARD1-BRCA1 complex is involved in genetic stabilization at the cellular level. It allows to mark abnormal DNA fragments by attaching ubiquitin to them. In addition, it blocks (by ubiquitination of RNA polymerase II) the transcription of damaged DNA. Ubiquitination, as well as stabilizing chromatin, or regulating the number of centrosomes, confirms the protective cooperation of BARD1 and BRCA1 in the stabilization of the genome. The overexpression of the oncogenic isoforms BARD1β and BARD1δ permit cancer development. The introduction of routine tests, for instance, to identify the presence of the BARD1β isoform, would make it possible to detect patients at high risk of developing cancer. On the other hand, introducing BARD1δ isoform blocking therapy, which would reduce estrogen sensitivity, may be a new line of cancer therapy with potential to modulate responses to existing treatments. It is possible that the BARD 1 gene offers new hope for improving breast cancer therapy.

Current oncological developments are based on improved understanding of genetics, and especially the discovery of genes whose alterations affect cell functions with consequences for the whole body. Our work is focused on the most important of these genes, the BARD1 and its oncogenic role in breast cancer. Most importantly, the study points to new avenues in the treatment and prevention of the most frequent female cancer based on BARD1 research. The BARD1 and BRCA1 proteins have similar structures and functions, and they combine to form the new molecule BARD1-BRCA1 heterodimer. Through ubiquitination, this heterodimer has significant effects on individual proteins, enabling, among others, the destruction of damaged DNA fragments. Ubiquitination, as well as stabilizing chromatin, or regulating the number of centrosomes, confirms the protective cooperation of BARD1 and BRCA1 in the stabilization of the genome. The overexpression of the oncogenic isoforms BARD1β and BARD1δ permit cancer development. The introduction of routine tests, for instance, to identify the presence of the BARD1β isoform, would make it possible to detect patients at high risk of developing cancer. On the other hand, introducing BARD1δ isoform blocking therapy, which would reduce estrogen sensitivity, may be a new line of cancer therapy with potential to modulate responses to existing treatments. It is possible that the BARD 1 gene offers new hope for improving breast cancer therapy.

Tumor biomarkers have great potential in screening and their role could extend further from general population risk assessment to treatment response estimation and recurrence monitoring. Different molecular and cellular elements in blood, which give information about the status of an individual, make it a perfect compartment to develop noninvasive diagnostics approaches for cancer. The present study aimed to screen the most frequent tumor markers in the Angolan population according to age and gender. A whole blood sample was collected for each patient. Serum levels were measured using the electrochemiluminescence method, using the automated Cobas e411 equipment (Roche®) according to the manufacturer's instructions. The results of our study elucidated the relevance of tumor biomarkers in screening for different types of cancer. These results also highlight the robustness of the mean in suspected cases, which is 15 to 17 times higher in some markers than in non-suspected cases. More research is needed to elucidate the relevance of these biomarkers in the Angolan population.

Parasite control strategies such as blanket anthelmintic treatment of all horses in a herd or interval treatment regimen based on egg reappearance remain widely followed practices for the last several decades. These practices have resulted in the fast emergence of resistance in equine strongyles to all major classes of drugs on the market. In this regard, the guidelines set by the American Association of Equine Practitioners advocate evidence-based strongyle control in horses. It recommends targeted treatment of all heavy egg shedders [&gt; 500 eggs per gram (EPG) of feces] while the low shedders (0-200 EPG) are left untreated to maintain susceptible parasite refugia in a herd. As 50-75% of adult horses in a herd are low shedders, preventing them from unnecessary anthelmintic exposure is critical to tackling resistance. There are various fecal egg count (FEC) techniques with many modifications and variations in use, but none is identified as a gold standard and methods comparison studies are lacking. We hypothesized that the diagnostic performance of commonly used quantitation methodologies differs and the FEC methods must be evaluated to determine the gold standard. In this regard, we performed methods comparison studies using polystyrene beads with size and specific gravity comparable to strongyle eggs, as proxy. The linearity of 12 commonly used FEC methodologies (3 techniques with 4 different solutions) was studied using bead standards in the clinically applicable range (63 to 1,000) to determine their suitability for strongyle egg counts. Deming regression analysis identified Mini-FLOTAC with sugar (specific gravity 1.33) as the test with the greatest coefficient of determination. All tests underestimated the true bead count, and we determined a correction factor (CF) for each test to estimate the true count. CF negates the preference for a gold standard test. Finally, we analyzed the validity of CF for 5 tests with R2&gt;0.95 to accurately quantify strongyle eggs from 40 different horses. Overall, this study identified methodologies with the highest diagnostic performance and the limitations to standardizing routine FEC tests to promote uniformity in implementing AAEP parasite control guidelines.

Water is a limited resource that needs to be properly managed and distributed to the ever-growing population of the world. Rapid urbanization and development have drastically increased the overall water demand worldwide. Ageing water distribution networks are vulnerable to deterioration and leakage, thereby causing an estimated annual loss of about 48 trillion liters of water. To address these issues, efficient and reliable leakage detection and management techniques are necessary. In this paper, the results of the experiments performed on a looped water distribution network in AnSeong, Korea are discussed. Transient-based techniques were used and physical data were collected for the detection and localization of leakages in the experimental water pipes. The results obtained from the experiments demonstrated the applicability of transient techniques for leak analysis in looped water distribution networks.

The main objective of this study focuses on designing and testing body protection systems using advanced materials based on aramid fibers, for high impact speeds of up to 410...430 m/s. The investigation of the failure mechanisms identifies issues of protective materials, major challenges and technological problems for efficient development of these systems. The authors presents an investigation on the failure processes and destructive stages of a ballistic package made of succesive layers of LFT SB1plus, taking into account the particular test conditions from NIJ Standard-0101.06 Ballistic Resistance of Body Armor. The main parameter of interest was the backface signature (BFS), but also details of projectile arrest and SEM investigaton could offer arguments in using this material for individual protection.

Background: Diabetes is a common non-communicable disease that is responsible for about 9% of all deaths and 25% reduction in life expectancy and nearly half of the diabetic patients are not aware of their disease. In this regard, diabetes screening to identify un-known diabetic patients is of great importance. Aims: The aims of this study were first to evaluate the performance of two commonly used diabetes screening tests that are currently recommended by the Iranian national screening program for diabetes (NSPD). Methods: The validities of the two diabetes screening tests were measured among 1057 participants older than 30 years. The studied screening tests included Capillary fasting blood glucose (CBG) and glycated hemoglobin (HbA1c). The golden standard for measuring the validity of the tests was venous fasting plasma glucose (VPG). Results: According to the results, the sensitivity of CBG and HbA1c tests were 69.01% and 84.5% and the specificity of the tests were 95.7% and 79.3% respectively. Positive and negative predictive values were 53.84% and 97.72% for CBG and 22.72% and 98.61% for HbA1c respectively. The recommended cut-points for CBG and HbA1c were 116.5 mg/dl and 7.15% respectively. Using these values as the new cut-points, sensitivity and specificity of CBG and HbA1c changed to 80.30% and 89.10%, and 77.50% and 94.20% respectively. Conclusions: Compared to several other countries, the performance of NSPD is relatively higher in Iran. ROC analysis suggested new cut-points for significantly better performance of NSPD.

Abstract: Spinal disorders are some of the most prevalent health concerns, especially among stu-dents. Based on student demographics, this cross-sectional study evaluated the correlation be-tween functional tests (FT) and spinal range of motion (ROM). This study included 206 students from Vasile Alecsandri University of Bacău. Participants' assessments were conducted using the following tests: (i) Ott, (ii) Schober, (iii) Stibor, (iv) finger-to-floor distance, (v) lateral flexion of the cervical and lumbar spine, and (vi) flexion of the cervical spine. Correlation analyses were evaluated using Spearman correlation coefficient analysis. The results indicated a very strong re-lationship between lateral flexion of the lumbar spine on the left (LFLSL) and right (LFSR) for all departments (r = 0.85 to 0.97, p < 0.05). There was a stronger relationship between FT results and spinal ROM of physical education department students compared to students from other de-partments (n = 17, r = -0.38 to 0.93, p < 0.05). There was no statistically significant correlation be-tween FT and spinal ROM based on age (p > 0.05). The study results provide evidence of the pri-mary risk factors that predispose students to postural deviations. Practitioners and physiothera-pists can utilize these values as a reference for potential therapeutic interventions.

Background and Objectives: Coagulation disorders during COVID-19 infection are associated with poor prognosis and disease severity, because two processes that interfere each other are thrombosis and inflammation. Very important issue for clinicians is timely and adequate hemostasis and inflammation monitoring in order to prevent and treat potentially lethal consequences. Materials and Methods: The study was approved by the Ethics Committee of the Clinical center Nis, Serbia. One hundered fourty two patients presented with COVID-19 ARDS were admitted to the ICU in Clinic for anesthesiology Clinical Center Nis, from 14th April 2020 to 25 th May 2020. On admission blood was collected for biochemical and coagulation testing. The data obtained was analyzed using Statistical Package for Social Sciences (SPSS v. 25, Chicago, IL, USA). Results: Among all parameters assessed, mortality was associated with higher age (p&lt;0.05), higher factor I (p&lt;0.05), INR (p&lt;0.001), D-Dimer (p&lt;0.001), ADP (p&lt;0.001), ASPI (p&lt;0.001), TRAP (p&lt;0.001), PSEP (p&lt;0.001), A5 extest (p&lt;0.01), A10 ex test (p&lt;0.01), A5 fib (p&lt;0.001), A10fib (p&lt;0.001) and MCF fib (p&lt;0.001) values, but lower CT extest values (p&lt;0.05). Mortality was associated with extreme values of D-Dimer above 1000 (p&lt;0.001), ADP above 590 (p&lt;0.001), ASPI above 800 (p&lt;0.001), TRAP above 1500 (p&lt;0.001) and PSEP above 1000 (p&lt;0.05). Conclusions: The key to success in the treatment of COVID 19 infection is timely and adequate therapy and patient monitoring, which is impossible without early risk stratification and mortality prediction. Sophisticated hemostasis parameters can contribute to early risk assessment, which was initially performed only on the basis of the patient's clinical status.

If a lubricant contains structures capable of conducting energy, reactions involving zinc dialkyldithiophosphate (ZDDP) may take place both very close to and away from the solid surfaces, with this indicating that ZDDP can be a highly effective anti-wear (AW) additive. The central thesis of this article is that the tribocatalytic effect is observed only when the energy emitted by the solids is transmitted by ordered molecular structures present in the lubricant, e.g., graphene. The friction tests were carried out for 100Cr6 steel balls in a sliding contact with uncoated or a:C-H-coated HS6-5-2C steel discs in the presence of polyalphaolefin 8 (PAO 8) as the lubricant, which was enhanced with graphene and/or ZDDP. There is sufficient evidence of the interactions occurring between ZDDP and graphene and their effects on the tribological performance of the system. It was also found that the higher the concentration of zinc in the wear area, the lower the wear. This was probably due to the energy transfer resulting from the catalytic decomposition of ZDDP molecules. Graphene, playing the role of the catalyst, contributed to that energy transfer.

This study reports the design of a dielectric resonator (DR) metasurface-based terahertz biosensor for rapid and accurate detection of different kinds of viruses (H1N1, SARA-COV-2, etc.). The characterization of the sensor is done by analyzing its absorbance properties with and without the presence of the H1N1 virus layer of different concentrations and electrical properties in the frequency range of 2.4 THz to 3 THz. A full-wave EM model of the sensor is designed using CST MWS software. The geometrical parameters of the proposed biosensor, as well as its dielectric constant of the virus swab, are varied to achieve good performance with an absorption level close to 1 (100%). A significant change in the resonating pick-up frequency owing to the variation in the effective refractive index of the realized sensor ensures the detection and classification of the different concentrations of the same or different viruses. The presented design could be used for the rapid detection of viruses with the added advantages of contactless, label-free, and accurate identification of different concentrations of viruses.

Tumour spheroids are fast becoming commonplace in basic cancer research and drug development. Obtaining high-quality data relating to the inner structure of spheroids is important for analysis, yet existing techniques often use equipment that is not commonly available, are expensive, laborious, cause significant size distortion, or are limited to relatively small spheroids. We present a high-throughput method of mounting, clearing, and imaging tumour spheroids that causes minimal size distortion. Spheroids are mounted in an agarose gel to prevent movement, cleared using a solution prepared from commonly available materials, and imaged using confocal microscopy. We find that our method yields high quality two- and three-dimensional images that provide information about the inner structure of spheroids.

Recently it was found from Cassini data that the mean recession speed of Titan from Saturn is v = 11.3 ± 2.0 cm/yr which corresponds to a tidal quality factor of Saturn Q ≈ 100 while the standard estimate yields Q ≥ 6 · 10⁴ . It was assumed that such a large speed v is due to a resonance locking mechanism of five inner mid-sized moons of Saturn. In this paper, we show that an essential part of v may come from a local Hubble expansion, where the Hubble-Lemaˆıtre constant H0 recalculated to the Saturn-Titan distance D is 8.15 cm/(yrD). Our hypothesis is based on many other observations showing a slight expansion of the Solar system and also of our Galaxy at a rate comparable with H0. We demonstrate that the large disproportion in estimating the Q factor can be just caused by the local expansion effect. [Accepted for publication in "Gravitation and Cosmology". The paper is to appear in Vol. 28, Issue 2 (2022) of the journal Gravitation and Cosmology.]

Five-day exposure of clary sage (Salvia sclarea) to 100 μM cadmium (Cd) in hydroponics was sufficient to increase Cd concentrations significantly in roots and aboveground parts and affect negatively whole plant levels of calcium (Ca) and magnesium (Mg), since Cd competes for Ca channels, while reduced Mg concentrations are associated with increased Cd tolerance. Total zinc (Zn), copper (Cu), and iron (Fe) uptake increased but their translocation to the aboveground parts decreased possible due to translocation barriers. Despite the substantial levels of Cd in leaves, without any observed defects on chloroplast ultrastructure, an enhanced photosystem II (PSII) efficiency was observed, with a higher fraction of absorbed light energy to be directed to photochemistry (ΦPSΙΙ). The concomitant increase in the photoprotective mechanism of non-photochemical quenching of photosynthesis (NPQ) resulted in an important decrease in the dissipated non-regulated energy (ΦNO), modifying the homeostasis of reactive oxygen species (ROS), through a decreased singlet oxygen (1O2) formation. Thus, when clary sage was exposed to Cd for a short period, tolerance mechanisms were triggered, with PSII photochemistry to be regulated by NPQ in such a way that PSII efficiency to be enhanced. However, exposure to a combination of Cd and high light or for longer duration (8 days) to Cd alone, resulted in an inhibition of PSII functionality pointing out towards Cd toxicity. Thus, the rapid activation of PSII functionality at short time exposures and the inhibition at longer duration suggests a hormetic response and describes these effects in terms of “adaptive response” and “toxicity”, respectively.

COVID-19 represents an unprecedented threat to global public health and economies. Assays are urgently needed for rapid detection and diagnosis of SARS-CoV-2-infected patients in order to inform treatment and quarantine strategies. Establishing globally accepted easy-to-access diagnostic tests is extremely important to understanding the epidemiology of the present pandemic. While nucleic acid-based tests are considered to be more sensitive with respect to serological tests, but the present gold standard RT-PCR-based assays possess limitations such as low sample throughput, requirement for sophisticated reagents and instrumentation. To overcome these shortcomings, recent efforts of incorporating LAMP-based isothermal detection, and minimizing the number of reagents required are on rise. Novel CRISPR- and other nuclease-based techniques, when merge with isothermal and allied technologies, promises to provide sensitive and rapid detection of SARS-CoV-2 nucleic acids. Here we discuss and present compilation of state-of-the-art CRISPR based detection techniques for use in COVID diagnosis and epidemiology.

A common motivation for increasing open access to research findings and data is the potential to create economic benefits – but evidence is patchy and diverse. This study systematically reviewed the evidence on what kinds of economic impacts (positive and negative) open science can have, how these comes about, and how benefits could be maximized. Use of open science outputs often leaves no obvious trace, so most evidence of impacts is based on interviews, surveys, inference based on existing costs, and modelling approaches. There is indicative evidence that open access to findings/data can lead to savings in access costs, labour costs and transaction costs. There are examples of open science enabling new products, services, companies, research and collaborations. Modelling studies suggest higher returns to R&D if open access permits greater accessibility and efficiency of use of findings. Barriers include lack of skills capacity in search, interpretation and text mining, and lack of clarity around where benefits accrue. There are also contextual considerations around who benefits most from open science (e.g. sectors, small vs larger companies, types of dataset). Recommendations captured in the review include more research, monitoring and evaluation (including developing metrics), promoting benefits, capacity building and making outputs more audience-friendly.

This study explores the innovative use of CO2 laser technology in frenuloplasty, a significant shift from traditional methods like scalpel surgery or electrocautery, towards a minimally invasive approach. The research involved 15 patients aged 25 to 50, undergoing frenuloplasty with a CO2 laser system equipped with a 7-inch defocused handpiece, set at 20Hz and 0.3W. This method diverges from conventional laser techniques, focusing on controlled laser passes combined with manual traction to elongate the fibrous tissue of the frenulum. The results demonstrated that the CO2 laser technique allowed for a precise and progressive modification of the frenulum, significantly reducing the risks of hemorrhage and secondary in-tention fibrosis. The healing process was notably expedited, with patients reporting satisfactory outcomes within a two-week period. Statistically significant improvements were observed in pa-tient-reported outcomes, as evidenced by the increases in the Short Form Health Survey (SF-12) scores, with the mean Physical Component Summary (PCS) score rising from 32.5 to 47.5 and the mean Mental Component Summary (MCS) score from 39.3 to 52.3 (p < 0.001 for both). The study concludes that CO2 laser frenuloplasty is an effective and safe technique, offering sub-stantial benefits in terms of reduced healing time and enhanced patient satisfaction. The signifi-cant improvements in SF-12 scores underscore the positive impact on patient quality of life, ad-vocating for the broader application of this technique in clinical practice. Further research is warranted to explore its potential in a wider clinical context.

A rapid and efficient method using an alkyl functionalized magnetic nanoparticles-based extraction technique combined with Ultra-High Performance Liquid Chromatography was developed for the detection of trace amounts of polycystic aromatic hydrocarbons in tea leaves. As a popular coating for chromatographic column packing materials, C18-alkyl has been demonstrated to be effective in separating polycystic aromatic hydrocarbons. And the magnetism of the nanomaterials accelerates the extraction process while their high surface ratio enables desirable dispersity in the sample matrix. Meanwhile, the adsorbents can be washed and reused 30 times without compromise on recovery, which greatly reduced the budget. The effects of various parameters were investigated and optimized, and the recoveries for five analytes were in the range of 84.8–103.7%. The reproducibility rate of intra-day and inter-day were below 7.1% and 11.3% respectively. The limits of detection and limits of quantification ranged from 1.69–9.97 ng g-1 and 5.12–30.21 ng g-1, indicating satisfactory sensitivity. Thus, the proposed methodology is rapid, highly efficient, and economical, and it expands the application of magnetic cleanup approaches in complex food matrices.