The application potential of cellulosic materials in natural composites and other fields needs to be explored to develop innovative, sustainable, lightweight, functional biomass materials that are also environmentally friendly. This study investigated Typha augostifolia (Typha sp.) as a potential new raw material for extracting cellulose nanocrystals (CNCs) for application in wastewater treatment composites. Alkaline treatments and bleaching were used to remove cellulose from the stem fibers. The CNCs were then isolated from the recovered cellulose using acid hydrolysis. The study showed a few distinct functional groups (O-H, -C-H, =C-H and C-O, and C-O-C) in the Fourier Transform Infrared (FTIR) spectra. Scanning electron microscope (SEM) revealed the smooth surface of CPC and CNCs that resulted from removing lignin and hemicellulose from powdered Typha augostifolia. Based on the crystalline index, the powdered Typha augostifolia, CPC, and CNCs were 42.86%, 66.94% and 77.41%. The loss of the amorphous section of the Typha sp. fiber resulted in a decrease in particle size. It may be inferred from the features of a Typha sp. CNC that CNCs may be employed as reinforcement in composites for wastewater treatment.

Yerba mate waste (YMW) were used to produce kombucha beverage, and the obtained microbial cellulose produced as by product (KMW) was used to reinforce mechanically recycled poly(lactic acid) (r-PLA) matrix. Microbial cellulosic particles were also produced in pristine yerba mate for comparison (KMN). To simulate the revalorization of industrial PLA products rejected during the production line, PLA was subjected to three extrusion cycles and the resultant pellets (r3-PLA) were then plasticized with 15 wt.% of acetyl tributyl citrate ester (ATBC) to obtain optically transparent and flexible films by solvent casting method. The plasticized r3-PLA-ATBC matrix was then loaded with KMW and KMN in 1 and 3 wt.%. The use of plasticizer allowed a good dispersion of microbial cellulose particles into the r3-PLA matrix, allowing to obtain flexible and transparent films which showed good structural and mechanical performance. Additionally, the obtained films showed antioxidant properties, as it was proven by release analyses conducted in direct contact with a fatty food simulant. The results suggest the potential interest of these recycled and biobased materials that are obtained from the revalorization of food waste for their industrial application in food packaging or agricultural films.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

Recycled tire fibers (RTF) are currently one of the most abundant waste not being recovered due to several processing hurdles and the presence of high amounts of residual ground rubber particles (GR). Therefore, this study proposes a simple approach to separate most of rubber particles from fibers and to determine their rubber content using thermogravimetric analysis (TGA)/calcination. Afterwards, clean fiber (CF) and GR are used as fillers for recycled post-consumer low density polyethylene (rLDPE), and their effects on the physical properties are investigated. Accordingly, a series of composites with CF and GR is prepared at different filler concentrations (0-30%) via extrusion compounding before using compression molding and injection molding for comparison. In all cases, injection molding leads to higher strength and modulus, but lower elongation at break. The results show that incorporating 30 wt.% of CF into rLDPE yields a remarkable improvement in tensile strength (15%), tensile modulus (192%) and flexural modulus (142%). On the other hand, the incorporation of up to 30 wt.% of GR results in a reduction of both tensile strength and flexural modulus by 15%, confirming the critical role of the cleaning process for RTF in achieving the best results.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

Our environment has been significantly impacted by man-made pollutants, primarily due to industries make substantial use of synthetic chemicals, resulting in significant environmental consequences. In this research investigation, the co-precipitation approach was employed for the synthesis of cellulose-based ferric oxide (Fe₂O₃/cellulose) and copper oxide nanoparticles (CuOx-NPs). Scanning electron microscopy (SEM) analyses were conducted to determine the properties of the newly synthesised nanoparticles. Furthermore, the synthesized nanoparticles were employed for eliminating chromium from aqueous media under various conditions, including temperature, contact time, adsorbent concentration, adsorbate concentration, and pH. Additionally, the synthesised materials were used to recover Cr(VI) ions from real samples, including tap water, seawater, and industrial water, and the adsorptive capacity of both materials evaluated under optimal conditions. The synthesis of Fe₂O₃/cellulose and CuOx-NPs proved to be effective, as indicated by the outcomes of the study.

The article provides an overview of nanocomposites and microelectronic elements used in space electronics and radiation control systems of nuclear reactors. Only those nanocomposites and microelectronic elements are taken into account that improve their characteristics in radiation fields or remain indifferent when exposed to ionizing radiation. Considering the chemical composition of the materials of these nanocomposites and microelectronic elements, it is analyzed from which radioactive materials (RM) obtained by recycling radioactive waste (RW) such composites and microelectronic parts can be made. Thus, an alternative way of radioactive waste disposal is proposed, when these wastes are used in the form of microelectronic elements designed to operate under conditions of cosmic radiation.

The article discusses an alternative way of recycling radioactive waste (RW), presented in the form of radioactive building materials - concrete and reinforced concrete structures and metal fittings, with the further use of materials, obtained during recycling, in the space industry. That is, it is supposed to send radioactive waste into space not as a passive ballast, but as a payload that will operate in space under conditions of increased radiation.

The production of biomass fly ash has been increasing every year in Europe, reaching 5.5 million tons in 2020. Biomass fly ash is not yet accepted in the standards as a substitute material for cement in mortar and concrete. In a first approach, the substitution limit of biomass fly ash is determined by comparing the mechanical strengths, fresh state properties and hardened properties of mortars produced with biomass fly ash to those of mortars produced with classical coal fly ash. Then, masonry and rendering mortars have been designed with different substitution rates of biomass fly ashes from wood combustion in thermal power plant. Although there is an overall decrease in performance, mortars made with biomass ash retain properties that make them suitable for use in masonry or rendering.

Recycled wastewater is considered as a sustainable source of irrigation water. Despite commendable safety records, viral contamination of agricultural products has occurred the past causing disease outbreaks. This review examines the apprehension that the novel coronavirus (SARS-CoV-2) may also spread through recycled wastewater irrigation (RWI) industry. The novel SARS-CoV-2 is now perceived as an enteric pathogen, and has been found to remain stable in the wastewater for days. Mounting evidences also suggest that viral particles shed by infected individuals through sewage, and greywater is much higher (up to 10 Log₁₀) than the amount typically removed (6-7 Log₁₀) through the recycled water disinfection processes. Such gap indicated an increased risk of infection through fecal-oral transmission route. This study also identified greywater irrigation schemes posing a higher risk of transmission of SARS-CoV-2. It was recommended that countries putting greywater in the ‘low risk’ category may rewrite the safety guidelines in post COVID-19 times. This review also suggest that the choice of irrigation method could be critical in protecting the farmers, and the consumers from possible infections during the pandemic. In this regard, irrigation methods (i.e. sprinkler) that generate airborne droplet (leading to aerosols) may be operated with caution when public spaces are in the vicinity. The study also indicated that the developing countries should regulate surface irrigation practice that pump water from polluted rivers during the pandemic.

Bio-based packaging materials and efficient drug delivery systems are gaining attention, carboxymethyl cellulose (CMC) is one of the most soluble cellulose derivatives, is a good candidate material due to its biocompatibility, biodegradability, and reproducibility. However, CMC-based films are lack of sufficient mechanical properties, limiting its widespread application. In this paper, the molecular interactions between CMC and additives with different molecular structures have been studied with rheological method. The additives are chitosan and cellulose derivatives including O-carboxymethylated chitosan (O-CMCh), N-2-hydroxypropyl-3-trimethylammonium-O-carboxymethyl chitosan (HTCMCh), hydroxypropyltrimethyl ammonium chloride chitosan (HACC), cellulose nanofibers (CNC), and cellulose nanofibers (CNF). The influencing factors, such as molecular structure, concentration of additives and temperature on the rheological properties were studied, which results revealed the information intermolecular interactions. Based on the rheological properties, several systems were selected to prepare films, which show very good transparency, wettability, mechanical properties, biodegradability, and cytotoxicity. These good characteristics of the selected films also proved the good biocompatibility of CMC and chitosan and cellulose derivatives. This work will provide an idea to prepare CMC-based food packaging and effective drug delivery materials with specific properties.

The novelty of this study consists in: i) synthesis and characterization of electrode materials recycled from a spent car battery and doped with MnO2 and CuO by the analysis of X-ray diffraction (XRD), Infrared (IR) and Electron Paramagnetic Resonance (EPR) data and ii) the investigation of electrochemical properties of prepared materials in view of new applications as electrode materials for battery. Electron Paramagnetic Resonance (EPR) data indicate that the intensity of the resonance line corresponding to the Cu+2 ion was modified with the increase of the dopant content. The analysis of X-ray Absorption Spectroscopy (XAS) data indicates that by increasing the dopant content there is a process of ordering the oxygen atoms around the lead similar to the PbO2 theoretical model. The electrochemical performances of the recycled and manganese-copper-doped materials are optimized for applications as new anodic electrode for the car battery.

High-density polyethylene (HDPE) waste poses a significant environmental challenge due to its non-biodegradable nature and the vast quantities generated annually. However, conventional recycling methods are energy-intensive and often yield low-quality products. Herein, HDPE waste is upcycled into anti-aging superhydrophobic thin films suitable for outdoor applications. A two-layer spin-casting method combined with heating-induced crosslinking is utilized to produce an exceptionally rough superhydrophobic surface, featuring a root mean square (RMS) roughness of 50 nm, an average crest height of 222 nm, an average trough depth of –264 nm, and a contact angle (CA) of 148°. To assess durability, weathering tests were conducted, revealing the films' susceptibility to degradation under harsh conditions. The films' resistance to environmental factors is improved by incorporating a UV absorber, maintaining their hydrophobic properties and mechanical strength. Our research demonstrates a sustainable method for upcycling waste into high-performance, weather-resistant superhydrophobic films.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

To obtain a cost-effective and high-performance composite material of polybutylene adipate-terephthalate (PBAT), for this study we selected microcrystalline cellulose, which is inexpensive and easily available, as the reinforcing medium. Hexadecyl trimethoxysilane (HDTMS) containing a long carbon chain was chosen to silanize the microcrystalline cellulose (MCC) to obtain silanized cellulose (SG). Three types of SGs with different degrees of silanization were obtained by controlling the reaction ratio. Characterization of these three types of SGs was conducted using FTIR, TEM, and water absorption analysis. Subsequently, PBAT/SG composites were prepared through a sol-gel method, and the effects of these three types of SGs on the thermal stability, compatibility, mechanical properties, and dynamic thermomechanical properties of PBAT were evaluated. Furthermore, the mechanism behind enhancing the mechanical properties of the composite was analyzed. The results demonstrated successful synthesis of SG. As the reaction ratio between HDTMS and MCC increased, the nanoparticle size increased, while the water absorption decreased significantly. After SG was added to the PBAT composites, the yield stress increased while maintaining good thermal stability. Both the SEM and DMA results indicated good compatibility of the PBAT/SG composites. Analysis of the mechanical properties revealed that the tensile strength initially increased and then decreased with increasing blending ratio for all three composites tested; among them, the PBAT/SG2 composites exhibit superior performance, with a maximum tensile strength reaching 22 MPa at an 85/15 blending ratio—nearly 30% higher than that of pure PBAT alone. The addition of SG significantly improved the strength of the PBAT, and we speculated as to the underlying mechanism involved. This study provides a new idea for the industrial-scale development of degradable polyesters with low cost and good mechanical properties.

The vulcanization of rubber compounds is an exothermal process. A carbon black-filled and natural rubber-based (NR) formulation was mixed with different levels of sulfur (0.5, 1.0, 2.0, 4.0 and 6.0 phr) and studied with Differential Scanning Calorimetry (DSC) for the determination of the vulcanization enthalpy. It was found that the vulcanization enthalpy is dependent from the amount of sulfur present in the compound and the vulcanization heat released was -18.4 kJ/mol S if referred to the entire rubber compound formulation or -46.0 kJ/mol S if the heat released is referred only to the NR present in the compound. The activation energy for the vulcanization of the rubber compounds was also determined by a DSC study at 49 kJ/mol and found quite independent from the sulfur content of the compounds under study. A simplified thermochemical model is proposed to explain the main reactions occurring during the vulcanization. The model correctly predicts that the vulcanization is an exothermal process although it gives an overestimation of the vulcanization enthalpy which is larger for the EV vulcanization package and smaller for the conventional vulcanization system. If the devulcanization is conducted mechanochemically in order to break selectively the sulfur-based crosslinks, then the natural rubber compounds recovered from used tires can be re-vulcanized again and the exothermicity of such process can be measured satisfactorily with DSC analysis. This paper not only proposes a simplified mechanism of vulcanization and devulcanization but also proposes an analytical method to check the devulcanization status of the recycled rubber compound in order to distinguish truly devulcanized rubber from reclaimed rubber.

This paper proposes the recycling of plates from spent car batteries by the melt quenching method and the incorporation of NiO or Co3O4 contents in order to improve the electrochemical performance of new materials for applications as electrodes on batteries. The analysis of X - ray diffractograms indicates the gradual decrease of the sulfated crystalline phases, respectively 4PbO•PbSO4 and PbO•PbSO4 phases until their disappearance for higher dopant concentrations. IR data show a decreasing trend in the intensity of the bands assigned to sulfate ions and a conversion of [PbO3] pyramidal units into [PbO4] tetrahedral units by doping with high dopant levels yielding to the formation of the PbO2 crystalline phase. The EPR data indicate three resonance lines centered on the gyromagnetic factor, g ~ 2, 2.2 and 8, which are dependent on the NiO level. The first two resonance lines are assigned to nickel ions in higher oxidation states and the last signal centered at g ~ 8 corresponds to nickel metal nanoparticles. This compositional evolution can be explained by considering a process of drastic reduction of nickel ions in oxidation states superior to metallic nickel. The linewidth and the intensity of resonance lines situated at about g ~ 2, 2.17, 4.22 and 7.8 corresponding to the Co+2 ions from EPR spectra depend very strongly on the Co3O4 concentration. The best reversibility of the cyclic voltammograms was highlighted for the samples with x = 8 mol% NiO and 10 mol% Co3O4, which are recommended as suitable in applications as electrode for renewable batteries.

Herein, we report a stimuli responsive hydrogel with inhibitory activity against Escherichia coli prepared by chemical crosslinking of carboxymethyl chitosan (CMCs) and hydroxyethyl cellulose (HEC). The hydrogels were prepared by esterification of chitosan (Cs) with monochloroacetic acid to produce CMCs which was then chemically crosslinked to HEC using citric acid as the crosslinking agent. To impart a stimuli responsiveness property to the hydrogels, polydiacetylene-zinc oxide (PDA-ZnO) nanosheets were synthesized in-situ during the crosslinking reaction followed by photopolymerization of the resultant composite. To achieve this, ZnO was anchored on carboxylic groups in 10,12-pentacosadiynoic acid (PCDA) layers to restrict movement of alkyl portion of PCDA during crosslinking CMCs and HEC hydrogels. This was followed by irradiating the composite with UV radiation to photopolymerize the PCDA to PDA within the hydrogel matrix so as to impart thermal and pH responsiveness to the hydrogel. From the results obtained, the prepared hydrogel had a pH dependant swelling capacity as it absorbed more water in acidic media as compared to basic media. Incorporation of PDA-ZnO resulted in a thermochromic composite responsive to pH evidenced by a visible colour transition from pale purple to pale pink. Upon swelling, PDA-ZnO-CMCs-HEC hydrogels had inhibitory activity against E. coli attributed to the slow release of the ZnO nanoparticles as compared to CMCs-HEC hydrogels.

A study to produce cellulose nanofibrils (CNF) from Kraft cellulose pulp, an optimal enzyme mixture, was defined using a centroid simplex mixture design. The enzyme blend contains 69% endoglucanase and 31% exoglucanase. The central composite rotational design (CCRD) optimized the CNF production process by achieving a higher crystallinity index. It thus corresponded to a solid loading of 15 g/L and an enzyme loading of 0.974. Using the Segal formula, the crystallinity index (CrI) of CNF was determined by X-ray diffraction to be 80.87%. The average diameter of nanocellulose fibers measured by scanning electron microscopy between 550 - 600 nm for the CNF prepared by enzymatic hydrolysis and between 250 - 300 nm for the CNF produced by enzymatic hydrolysis with the optimal enzyme mixture followed by ultrasonic dispersion. Finally, synergistic interactions between the enzymes involved in nanocellulose production were demonstrated, with Colby factor values greater than one.

Chemical modification of cellulose offers routes for structurally and functionally diverse biopolymer derivatives for numerous industrial applications. Among cellulose derivatives, cellulose ethers have found extensive use, such as emulsifiers, in food industries and biotechnology. Methylcellulose, one of the simplest cellulose derivatives, has been utilized for biomedical, construction materials and cell culture applications. Its improved water solubility, thermoresponsive gelation, and the ability to act as a matrix for various dopants also offer routes for cellulose-based functional materials. There has been a renewed interest in understanding the structural, mechanical, and optical properties of methylcellulose and its composites. This review focuses on the recent development in optically and mechanically tunable hydrogels derived from methylcellulose and methylcellulose-cellulose nanocrystal composites. We further discuss the application of the gels for preparing highly ductile and strong fibers. Finally, the emerging application of methylcellulose-based fibers as optical fibers and their application potentials are discussed.

The steady rheological behavior of suspensions of solid particles thickened by cellulose nanocrystals is investigated. Two different types and sizes of particles are used in the preparation of suspensions, namely TG hollow spheres of Sauter mean diameter of 69 µm and Solospheres S-32 of Sauter mean diameter of 14 µm. The nanocrystal concentration varies from 0 to 3.5 wt% and the particle concentration varies from 0 to 57.2 vol%. The influence of salt (NaCl) concentration and pH on the rheology of suspensions is also investigated. The suspensions generally exhibit shear-thinning behavior. The degree of shear-thinning is stronger in suspensions of smaller size particles. The experimental viscosity data are adequately described by a power-law model. The variations of power-law parameters (consistency index and flow behavior index) under different conditions are determined and discussed in detail.

Named herein “CytroCell”, the cellulosic material obtained via hydrodynamic cavitation of citrus processing waste in water is cellulose of low crystallinity, high porosity, good water holding capacity and good dispersibility in water. These properties, here demonstrated for the first time for lemon and grapefruit CytroCell, open the route to mass scale production of a useful functional material from a cheap and abundant biowaste. The process, indeed, does not require any pre-treatment of the raw material, and does not use acid, alkali, chemical oxidants or enzymes.

Antimicrobial and anti-viral materials have attracted significant interest in recent years due to increasing occurrences of nosocomial infections and pathogenic microbial contamination. One method to address this is the combination of photoactive compounds that can produce reactive oxygen species (ROS), such as hydrogen peroxide and hydroxyl radicals to disinfect microbes, with carrier materials that meet the application requirements. Using anthraquinone (AQ) and cellulose nanocrystals (CNCs) as the photoactive and carrier components respectively, this work demonstrates the first covalent incorporation of AQ onto CNCs. The morphology and the photoactive properties were investigated, revealing the structural integrity of the CNCs, and high degree of photoactivity of AQ-CNC materials upon UVA exposure. The AQ-CNCs also exhibited an unexpected persistent generation of ROS under darkness, which adds advantages for antimicrobial applications.

Over the past decades, research has escalated on the use of polylactic acid (PLA) as replacement for petroleum-based polymers. This is due to its valuable properties, such as renewability, biodegradability, biocompatibility and good thermomechanical properties. Despite possessing good mechanical properties comparable to conventional petroleum-based polymers, PLA suffers from some shortcomings such as low thermal resistance, heat distortion temperature and rate of crystallization, thus different fillers have been used to overcome these limitations. In the frame work of environmentally friendly processes and products, there has been growing interest on the use of cellulose nanomaterials viz. cellulose nanocrystals (CNC) and nanofibers (CNF) as natural fillers for PLA towards advanced applications other than short-term packaging and biomedical. Cellulosic nanomaterials are renewable in nature, biodegradable, eco-friendless and they possess high strength and stiffness. In the case of eco-friendly processes, various conventional processing techniques, such as melt extrusion, melt-spinning, and compression moulding, have been used to produce PLA composites. This review addresses the critical factors in the manufacturing of PLA-cellulosic nanomaterials by using conventional techniques and recent advances needed to promote and improve the dispersion of the cellulosic nanomaterials. Different aspects, including morphology, mechanical behavior and thermal properties, as well as comparisons of CNC- and CNF reinforced PLA, are also discussed

Membranes are a selective barrier that allows certain species (molecules and ions) to pass through while blocking others. Some rely on size exclusion, where larger molecules get stuck while smaller ones permeate through. Others use differences in charge or polarity to attract and repel specific species. Membranes can be used to purify air and water by allowing only air and water molecules to pass through but preventing contaminants such as microorganisms and particles or to separate target gas or vapor, such as H2, CO₂, from other gases. The higher the flux and selectivity, the better a material is for membranes. The desirable performance can be tuned through material type (polymers, ceramics, and biobased materials), microstructure (porosity and tortuosity), and surface chemistry. Most membranes are made from plastic from petroleum-based resources, which contribute to global climate change and plastic pollution. Cellulose can be an alternative sustainable resource to make renewable membranes. Cellulose exists in plant cell walls as natural fibers, which can be broken down into smaller components such as cellulose fibrils, nanofibrils, nanocrystals, and cellulose macromolecules through mechanical and chemical processing. Membranes made from reassembling these particles and molecules have variable pore architecture, porosity, and separation properties and therefore have a wide range of applications in nano-, micro-, and ultrafiltration or forward osmosis. Despite their advantages, cellulose membranes face some challenges. Improving the selectivity of membranes for specific molecules often comes at the expense of permeability. The stability of cellulose membranes in harsh environments or under continuous operation needs further improvement. Research is ongoing to address these challenges and develop advanced cellulose membranes with enhanced performance. This article reviews the microstructure, fabrication methods, and potential applications of cellulose membranes, providing some critical insights into processing-structure-property relationships for current state-of-the-art cellulosic membranes that could be used to rationally improve their performance.

Post-industrial recycling (PIR) and post-consumer recycling (PCR) are measures to sustain re-sources by improving materials’ circularity and sustainability. Currently, circularity is mostly measured as the degree of reutilization of a material from 0 to 100 % at product or company lev-el. This lacks in assessing the resources’ usage over multiple product life cycles. Therefore, we propose to assess circularity as (i) the frequency resources are used in products (effective circu-larity eC) and (ii) a vehicle to reduce virgin resource use and environmental impacts (environ-mentally efficient circularity eeC). Besides, to compare the environmental impacts of using recy-cled materials from PIR or PCR, we analyse their impact reduction potential (IRP) indicating the environmental benefits of recycling in relation to virgin material put onto the market. We demonstrate the suggested indicators for a case study material: polypropylene. For this polymer type, the eC ranges between 0.93 and 9.08 uses of the resource on average depending on collec-tion, sorting, and recycling rates. Likewise, the eeC ranges between 0.31 and 1.50 uses per kg of CO2 equivalents emitted. PCR has a higher IRP regarding climate change impacts than PIR in all analysed scenarios. The results reveal the relevance of PCR and PIR beyond the product life cycle.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

The performance of recycled aggregate concrete deteriorates due to the defects of adhesive mortar, pores and cracks on the surface of recycled aggregate. It is of great engineering significance to modify the reclaimed aggregate to improve its performance and adaptability. In this paper, the physical and chemical properties of waste concrete recycled aggregate are reviewed. Then, the existing modification methods and technologies of recycled aggregate, including physical, chemical and biological methods, are reviewed. Finally, the existing problems of the current modification technology are summarized, and the future research direction is proposed. It is expected to provide a new idea and method for the modification of waste concrete recycled aggregate.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

The pursuit of an environmentally sustainable manufacturing process advocates for the substitution of harmful reagents for less damaging and recyclable solutions. This study aims to assess the effectiveness of using cellulose microfibrils synthesized via different hydrolysis reactions as reinforcing agents in polyvinyl alcohol (PVA) at varying con-centrations. The investigation explores the morphology, thermal properties, and chemi-cal behavior of the cellulose particles. The cellulose microfibrils (CMF) produced using citric acid exhibited the highest yield and aspect ratio. Notably, particles from organic acids demonstrated greater thermal stability, with oxalic acid-derived particles displaying the maximum thermal degrada-tion temperature. Subsequently, cast films of PVA reinforced with the cellulose microfibrils underwent comprehensive analyses, including Fourier transfer infrared (FTIR) spectroscopy, thermal degradation temperature (Td), differential scanning calorimetry (DSC), and tensile strength tests. The thermal behavior of cast films experienced notable changes with the addition of cellulose particles, evidenced by increased melting and crystallinity temperatures, along with a rise in the degree of crystallinity. The incorporation of cellulose particles led to a substantial improvement in mechanical properties. Films containing CMF dis-played higher Young’s modulus, and the sample incorporating 5% CMF derived from citric acid exhibited the most significant increase in modulus.

There are various biomaterials in nature, but none fulfills all the requirements. Cellulose, eco-friendly material-based biopolymers, have been advanced biomedicine to satisfy most market demand and circumvent many ecological concerns. This review aims to present an overview of the state of the art in cellulose's knowledge and technical biomedical applications. It included an extensive bibliography of recent research findings for fundamental and applied investigations. The chemical structure of cellulose allows modifications and simple conjugation with several materials, including nanoparticles, without tedious efforts. Cellulose-based materials were used for biomedicine applications such as antibacterial agents, antifouling, wound healing, drug delivery, tissue engineering, and bone regeneration. They advanced the applications to be cheap, biocompatible, biodegradable, easy for shaping and processing into different forms, with suitable chemical, mechanical and physical properties.

The reuse of recycled crushed concrete aggregate (RCCA) and reclaimed asphalt pavement (RAP) can provide a sustainable solution for the disposal of C&amp;D materials instead of sending it to landfill. More importantly, it will save energy and reduce impact on the environment. Several states in USA are using RCCA and RAP as base materials for years, focusing on the quality of the recycled materials. The structure of Recycled Aggregate (RA) is more complex than Natural Aggregate (NA). RAs have old mortar adhered on them that forms a porous surface at interfacial transition Zone (ITZ) and prevents new cement mix from bonding strongly with the aggregates. The objective of this work was to correlate microstructural properties like micro-porosity, inter and intra aggregate pores with the unconfined compressive strength (UCS) of RAP and RCCA molds, mixed at different proportions. In this paper, the quantity of micro-pores and their effect on the strength of mixed materials is used as the basis of microstructural analysis of recycled concrete and reclaimed asphalt. Microstructural properties obtained from the analysis of scanning electron microscope (SEM) images were correlated with unconfined compressive strength. Intra-aggregate and inter-aggregate pores were studied for different ratios of cement treated mixture of RAP and RCCA. The results show that the number of pores in the mixture increases considerably by adding RAP, which eventually causes reduction in unconfined compressive strength. In addition, significant morphological and textural changes of recycled aggregates were observed by SEM image analysis.

In this study, four samples of recycled aggregates from construction and demolition waste of Mexico City were characterized, in order to find innovative uses for this type of materials. Gravel and sand from a recycling plant were analyzed, as well as recycled aggregates in the laboratory from demolished concrete collected in landfills. The characterization was carried out by means of XRD, chemical microanalysis (EDS), pH measurement and sieve analysis. The results reveal that the minerals present in the analyzed materials are triclinic feldspars, cristobalite and pyroxene which correspond to the natural aggregates, as well as variable amounts of calcite, product of the carbonation of the cement paste adhered to these aggregates and in a smaller proportion calcium hemicarboaluminate, rosenhanite and tobermorite. It was determined that the quality (amount of cement) of the original concrete that was recycled, has great influence on the granulometry and the chemical-mineralogical composition of the aggregates, since there will be different quantities and qualities of cement paste adhered to the aggregates of according to size. Finally the pH values measured in all samples fluctuate between 10.15 and 12.08, therefore it is suggested that these materials can be used in soil stabilization.

Spent batteries recycling is an important way to obtain low-cost graphite. Nevertheless, the obtaining of crystalline graphite with a rather low density of defects is required for many applications. In the present work, high-quality graphites have been obtained from different kinds of spent batteries. Black masses from spent alkaline batteries (batteries black masses, BBM), and lithium-ion batteries from smartphones (smartphone black masses, SBM) and electric and/or hybrid vehicles (lithium-ion black masses, LBM) were used as starting materials. A hydrometallurgical process was then used to obtain recycled graphites by acidic leaching. Different leaching conditions were used depending on the type of the initial black mass. The final solids were characterized by a wide set of complementary techniques.

Circular Economy involves structural changes in traditional business models and consumers’ behaviour toward recycled products. The recycling of PET products has been increasing but there is still a gap between consumption and demand for PET packaging in Brazil. In this research, the waste reduction was examined under a projective scenario to the current ecological purposes in Brazil for reducing environmental pollution. In that manner, this paper aimed to comprehend the intention to purchase recycled PET products of Brazilian consumers. With a non-probabilistic and convenience sample, the study counts 422 participants. The method employed was based on Structural Equation Modelling and Partial Least Squares, used to test the hypotheses of causality among the variables. Results showed the perception of low quality about recycled products reduced consumers’ intention to purchase. Also, the sustainability of recycled products positively influenced the intention to purchase. In addition, recycled products presented a negative impact on the perceived safety, which could influence the purchase of recycled products in Brazil. We conclude that the image that Brazilian consumers have about recycled products positively affects the intention to purchase.

Nonwovens made of recycled carbon fibers (rCF) and thermoplastic (TP) fibers have excellent economic and ecological potential. In contrast to new fibers, recycled carbon fibers are significantly cheaper and the CO2 footprint is mostly compensated by energy savings in the first product life cycle. The next step for this promising material is its industrial serial use. Therefore the process chain from fiber to composite material is analyzed. Initially rCF length at different positions during the carding process is measured. Thereafter the influence of the TP fibers onto processing, fiber shortening and mechanical properties is evaluated. At last several nonwovens with different TP fibers and fiber volume contents between 15 vol.-% and 30 vol.-% are produced, consolidated by hot pressing and tested by 4-point bending to determine the mechanical values. The fiber length reduction ranges from 20.6 % to 28.4 %. TP fibers cushion the rCF against mechanical stress but hold rCF fragments back due to their crimp. The resulting bending strength varies from 301 MPa to 405 MPa and the stiffness from 16.3 GPa to 30.1 GPa. Design recommendations for reduced fiber shortening are derived as well as material mixtures which offer better homogeneity and higher mechanical properties.

Filter Media (FM) sourced from recycled organic and mineral material offers a low cost and effective means of treating urban stormwater. Using recycled materials rather than from an increasingly scarce source of virgin materials (typically sandy loam soil) can ensure a sustainable long-term economy and environment. This paper presents results from the laboratory analysis and mathematical modeling to highlight the performance of recycled organic and mineral material in removing nutrients and metals from stormwater. Analysis included physical and chemical characterisation such as particle size distribution, saturated hydraulic conductivity (Ksat), bulk density, effective cation exchange capacity, and pollutant removal performance. Design mixes (DM), comprising a combination of organic and mineral materials, were characterised and used to develop/derive modelling design within the Model for Urban Stormwater Improvement Conceptualisation (MUSIC v6) [1]. Comparison is made to the Adoption Guidelines for Stormwater Biofiltration Systems - Summary Report [2] which were based on the Facility for Advancing Water Biofiltration (FAWB) guidelines to assist in the development of biofiltration systems, including the planning, design, construction and operation of those systems. An observed outcome from over two decades of biofiltration guideline development has been the exclusion of alternative biofilter materials due to claims of excessive leaching. Results from this study indicate that high nutrient and metal removal rates can be achieved over a range of hydraulic conductivities using design mixes of recycled organic and mineral materials that have a demonstrated equivalence to existing guideline specifications.

The effect of reprocessing on the quasi-static uniaxial tensile behavior of two commercial polypropylene (PP) based composites is experimentally investigated and modeled. In particular, the studied materials consist of an unfilled high-impact PP and a talc-filled high-impact PP. These PP composites are subjected to repeated processing cycles including a grinding step and an extrusion step to simulate recycling at the laboratory level, the selected reprocessing numbers for this study being 0, 3, 6, 9 and 12. Because the repeated reprocessing leads to thermo-mechanical degradation by chain scission mechanisms, the tensile behavior of the two materials exhibits a continuous decrease of elastic modulus and failure strain with increasing number of reprocessing. A physically consistent three-dimensional constitutive model is used to predict the tensile response of non-recycled materials with strain rate dependence. For the recycled materials, the reprocessing effect is accounted by incorporating the reprocessing sensitive coefficient into the constitutive model for Young’s modulus, failure strain, softening and hardening equations. Our predictions of true stress - true strain curves for non-recycled and recycled 108MF97 and 7510 are in a good agreement with experimental data.

Counterfeiting electronic components is a serious problem for the security and reliability of any electronic systems. Unfortunately, the number of counterfeit components has increased considerably after the introduction of horizontal semiconductor supply chain. In this paper, we propose a new method for detecting recycled Flash memory, a major target of the counterfeiters due to its ubiquitous usage. Proposed method is based on measurement of change in Flash array characteristics (such as erase time, program time, fail bit count, etc.) with its usage. We find that erase time is the best metric to distinguish a used Flash chip from a fresh one for the following reasons: (1) erase time shows minimal variation among different fresh memory blocks/chip and (2) erase time increases significantly with usage. We verify our method for a wide range of commercial off the shelf Flash chips from several vendors, technology nodes, storage density and storage type (single-bit per cell and multi-bit per cell). The minimum detectable chip usage varies from 0.05% to 3.0% of its total lifetime depending on the exact details of the chip.

The tailoring of the surface properties of cellulose nanocrystals (CNCs) to meet various requirements in environmental, food, and material areas has always been of great interest. In this study, the surface chemistry of CNCs was noncovalently modified by cetyltrimethylammonium bromide (CTAB), followed by characterizations and an application as a coating material for interfacial interaction investigation over various substrates. Due to the CTAB modification, the surface charge of the CNCs was neutralized, resulting in an increased size of each nanocrystal at the aqueous status and the aggregated microfibers when dried up. The CTAB modification not only decreased the crystallinity of the samples from 48.57% to 9.12% but also hydrophobized the CNCs and decreased their total surface energy. Finally, the adsorption behavior of the CNCs and CTAB-CNCs over nonionic, anionic, and cationic polymers was investigated by ellipsometry. Based on the thickness of the CNC and CTAB-CNC layers over 2-Hydroxyethyl cellulose (HEC), carboxymethyl cellulose (CMC), and polyethyleneimine (PEI), we proposed that the adsorption behavior was overall influenced by electrostatic interaction, hydrogen bonding, and van der Waals forces and the thickness of the adsorbed layers could be impacted by both the surface charge and the size of the crystals.

Additive manufacturing, commonly referred to as 3D printing, is an exciting and versatile manufacturing technology that is gaining traction and interest in both academic and industrial settings. Polymeric materials are essential components in a majority of the “inks” used across the various 3D printing technologies. As the environmental ramifications of sole or primary reliance on petrochemicals as a resource for industrial polymers continue to manifest themselves at a global scale, a transition to more sustainable bioderived alternatives could offer solutions. In particular, cellulose is promising due to its global abundance, biodegradability, excellent thermal and mechanical properties, and ability to be chemically modified to suit various applications. Thus far, cellulose has typically been incorporated in additive manufacturing applications as a substrate, filler, or reinforcement for other materials. However, due to its versatility and desirable properties, the exploration of all-cellulose 3D printing materials and associated methodologies is increasing. This review will discuss the progress and status of all-cellulose 3D printing approaches, associated challenges, and their potential as a key player in a more sustainable industrial future.

Cellulose nanocrystals (CNCs) are cellulose-derived nanomaterials that can be easily obtained, e.g., from vegetable wastes produced by circular economies. They show promising antimicrobial activity and the absence of side effects and toxicity. This study investigated the ability of CNCs to reduce microbial adherence and biofilm formation using in vitro microbiological models reproducing the oral environment. Microbial adherence by microbial strains of oral interest, Streptococcus mutans and Candida albicans was evaluated on the surfaces of salivary pellicle-coated enamel disks in the presence of different aqueous solutions of CNCs. The antibiofilm activity of the same CNC solutions was tested against S. mutans and an oral microcosm model based on mixed plaque inoculum using a continuous-flow bioreactor. Results showed an excellent anti-adherent activity of the CNCs against the tested strains from the lowest concentration tested (0.032 wt.%). Such activity was significantly higher against S. mutans than C. albicans, suggesting a selective anti-adherent activity against pathogenic strains. At the same time, there was a minimal albeit significant antibiofilm activity (at least 0.5 and 4 wt.% CNC solution for S. mutans and oral microcosm, respectively). This makes CNCs particularly interesting as anticaries agents, encouraging their use in the oral field.

Given its exceptional attributes, aerogel is viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porousness, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textile sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogel formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multi-functionality of cellulose-based aerogels in the textile industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

Three-dimensional (3D) printing technologies are transforming the design and manufacture of components and products across a variety of disciplines, however their application in the construction industry is still limited. Material deposition processes can achieve infinite geometries and have advanced from rapid prototyping and model-scale markets to their application in fabricating functional products, large objects and the construction of full-scale buildings. Many international projects have recently been realized and the construction industry is beginning to utilise these dynamic technologies. The potential advantages for integrating 3D printing into house construction are significant, these include the capacity for mass customization of designs and parameters for functional and aesthetic purposes, reduction in construction waste from highly precise material placement, and the use of recycled waste products in layer deposition materials. With the ultimate goal of improving construction efficiency and decreasing building costs, applying Strand7 Finite Element Analysis software, a numerical model was designed specifically for 3D printing in a cement mix incorporated with recycled waste product High Density Polyethylene (HDPE) and found that construction of an arched truss-like roof was structurally feasible without the need for steel reinforcements. The lab sizes prototypes were manufactured based on the destined numerical model by using a 3D printing technology. Currently available 3D printing technologies can be adopted for building construction and this paper discusses the applications, advantages, limitations and future directions of 3D printing as an innovative and viable solution for affordable house construction.

The automotive industry needs to improve energy efficiency rapidly to achieve carbon neutrality while creating a safe, secure, comfortable driving environment for customers. Porous sound-absorbing materials and porous thermal insulators are typically used to satisfy these requirements despite limitations in mass and space. While these porous materials are similar, the microstructures they offer for high performance differ in the size and connectivity of their fluid phases, which enhances the difficulty of achieving excellent sound absorption and thermal insulation in the same material. In this study, a hydrophobic cellulose nanofiber–poly(methylsiloxane) xerogel composite was developed using computational microstructure modeling. This porous material has high porosity and excellent thermal insulation and sound absorption properties.

This study focuses on the increased risk of high heat release and asphyxiation (toxic gas poisoning) in the event of a fire of polyurethane (PU) and MDF-based building materials, which are commonly used in building fires. Among them, polyurethane (PU) building materials are essential for buildings except in Europe and some other countries due to their excellent thermal insulation performance, but problems of short-term heat release and spread of toxic gases in the event of a fire continue to occur. To overcome these problems, researchers are actively working on introducing various flame retardants into building materials. Therefore, in this study, we produced a laboratory-sized (500mm*500mm) plate flame retardant board that can be utilized as a building material with a lower heat release rate and a lower toxicity index by mixing expanded graphite and ceramic binder as flame retardants in a main material based on the cellulose of waste paper by replacing the existing building materials with a hot-press method. According to the ISO-5660-1 test on the heat release rate of the plate flame retardant board, the THR value was 2.9 (MJ/m2) for 10 minutes, showing an effect of reducing the THR value by 36.3 (MJ/m2) compared to the THR value of 39.2 (MJ/m2) of the specimen made using only paper. In addition, the toxicity index of the flame retardant board was checked through the NES 713 test. As a result, the test specimen showed a toxicity index of 0.7, which is 2.4 lower than the toxicity index of 3.1 of MDF, which is utilized as a conventional building material. Based on the results of this study, the cellulose fire retardant board showed the effect of reducing the heat release rate and toxicity index of building materials in a building fire, which reduces the risk of rapid heat spread and smoke toxicity. This has the potential to improve the evacuation time (A-SET) of evacuees in fires. It is also important to show that recycling waste paper and utilizing it as the main material for building materials can be an alternative in terms of sustainable development.

The brittle shear failure of reinforced concrete beams is complexed and unfavorable. For decades, research on the mechanical properties and durability of recycled coarse aggregate (RCA) to make recycled aggregate concrete (RAC) has been widely investigated. However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and contradictory. This paper reports the shear strength of reinforced recycled aggregate concrete beams without stirrups. Eight RAC beams and two controlled beams with natural coarse aggregate (NCA) were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. Parameters in this study were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (w) of 1.16% and 1.80%. It was found that the normalized shear stresses of RAC beams with w = 1.80% at all levels of replacement percentage were quite similar to that of the NAC counterparts. Normalized shear stress of the beam with 100% RCA and w = 1.16% was lower than that of the NAC beam by 5%. Database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the ability of the most recent ACI 318-19 shear provisions in shear strength prediction. A reduction factor of 0.75 is proposed to the current ACI code provision to account for the physical variations of RCA such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

The paper presents the influence of different curing conditions – wet, dry and protection against water evaporation on selected properties of concretes with different amount of recycled concrete aggregate previously subjected to atmospheric CO2 sequestration. Additionally, the eco-efficiency bi and ci indexes as well as eco-durability S-CO2 index were calculated. It was found that dry conditions deteriorate the properties of concrete, especially made of blast furnace slag cement, while protection against evaporation allows to achieve results comparable to wet conditions. Moreover, for series with the highest amount of coarse recycled aggregate and after longer period of curing, the difference between the effects of wet curing and protection against water evaporation disappears. The eco-efficiency and eco-durability indexes approach confirms the beneficial effect of blast-furnace slag cement used as a binder but on condition of proper way of curing.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

Nisin is a 3.4 kDa antimicrobial peptide, produced by Lactococcus lactis (ATCC 11454). This bacteriocin can inhibit spores gemination and gram-positive bacteria development and has gained visibility in therapeutic use. The bacterial cellulose (CB) has been considered an ideal material and with high quality applied in food and medical-pharmaceutical inputs. Because of all this benefits, it is important to know the system proceeding of CB with nisin. Therefore, it was realize nisin release profile analysis of CBs was performed; analysis of the minimum inhibitory concentration (MIC) of nisin against Escherichia coli ATCC 25922, Pseudomonas aeuroginosa ATCC 9721 and Staphylococus aureus ATCC 10390; antimicrobial stability test, for 100 days at different temperatures of 4º, 25º and 37 ° C against microorganisms: S. aureus e L. sakei. The results show that nisin is released by the CB in 4 hours of contact with medium and the MIC of nisin is 78 µg/mL for S. aureus, doesn’t have gram-negative inhibition. It had stability until 100 days against L. sakei and 60 days for S. aureus. The system proved to be efficient and CB potentiated the antimicrobial action of nisin, acting as a selective barrier for other compounds present in the standard solution, serving as protection of the peptide at different temperatures. The CB loading system can be an ideal antimicrobial stability system for nisin.

The difficult current environmental situation, caused by construction industry residues containing ceramic materials could be improved by using these materials as recycled aggregates in mortars, with their processing causing a reduction in their use in landfill, contributing to recycling and also minimizing the consumption of virgin materials. Although some research is currently being carried out into recycled mortars, little is known about their stress-strain (σ-ε); therefore this work will provide the experimental results obtained from recycled mortars with recycled ceramic aggregates (with contents of 0, 10, 20, 30, 50 and 100%), such as: the density, the compression strength, as well as the σ-ε curves representative of their behavior. The values obtained from the analysis process of the results are those of: σ (elastic ranges and failure maximum), ε (elastic ranges and failure maximum), and Resilience and Toughness; in order to finally obtain, through numerical analysis, the equations to predict their behavior (related to their recycled content). At the end of the investigation it is established that mortars with recycled ceramic aggregate contents of up to 20% could be assimilated just like mortars with the usual aggregates, and the prediction equations produced could be used in cases of similar applications.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

Iron oxide nanoparticles have been investigated due to their suitable characteristics for diverse applications in the fields of biomedicine, electronics, water/wastewater treatment and sensors. Maghemite, magnetite and hematite are the most widely studied iron oxide particles and have ferrimagnetic characteristics. When very small, however, these particles have superparamagnetic properties and are called superparamagnetic iron oxide nanoparticles (SPIONs). Several methods are used for the production of these particles, such as coprecipitation, thermal decomposition and microemulsion. However, the variables of the different types of synthesis must be assessed to achieve greater control over the particles produced. In some studies, it is possible to compare the influence of variations in the factors for production with each of these methods. Thus, researchers use different adaptations of synthesis based on each objective and type of application. With coprecipitation, it is possible to obtain smaller, more uniform particles with adjustments in temperature, pH and the types of reagents used in the process. With thermal decomposition, greater control is needed over time, temperature as well as the proportion of surfactants and organic and aqueous phases in order to produce smaller particles and a narrower size distribution. With the microemulsion process, the control of the confinement of the micelles formed during synthesis through the proportions of surfactant and oil makes the final particles smaller and less dispersed. These nanoparticles can be used as additives for the creation of new materials, such as magnetic bacterial cellulose, which has different innovative applications. Composites that have SPIONs, which are produced with greater rigour with regards to size and distribution, have superparamagnetic properties and can be used in medical applications, whereas materials containing larger particles have ferromagnetic applications. To arrive at a particular particle with specific characteristics, researchers must be attentive to both the mechanism selected and the production variables to ensure greater quality and control of the materials produced.

Hydrothermal carbonization of cellulose was examined at 240 ℃ for 1 h. Ammonium sulfate and thiourea were selected as the doping sources of inorganic nitrogen and organic nitrogen for the preparation of supercapacitor carbon. The effect of boric acid on the properties of the resulting hydrochar after KOH activation was examined. The results showed that the proportion of functional groups and the specific surface area of the activated hydrochar would be reduced after the addition of boric acid, and the pore-forming process of the micropores would be inhibited. The hydrochar obtained from the reaction of cellulose and organic nitrogen compounds had better pore size distribution and electrochemical properties after activation. The largest specific surface area (952.27 m2 g-1) was obtained when only thiourea was used as the only doping source. In the three-electrode system, the specific capacitance resulting activated hydrochar reached 236.25 F g-1 at a current density of 1 A g-1. After 20,000 cycles of charging and discharging at a current density of 10 A g-1, the capacitance retention rate reached 99.96%. Therefore, this study proves that the supercapacitor carbon with good electrochemical properties could be obtained by the direct reaction of cellulose with organic nitrogen compounds.

The surface plasmon resonance of gold nanoparticles causes visible light absorption and scattering effects that may be used in optical coatings for eliminating blue light emission from display monitors, blocking UV light and for decorative applications. This study examines the achievement of functional properties provided by gold nanoparticles in a commercially established C60 fullerene-coated eyewear product. The gold nanoparticles used were sourced from recycling rapid lateral flow tests (LFIA), which use gold nanoparticles as test markers. After the gold`s recovery Ultrasonic Spray Pyrolysis (USP) with freeze-drying was used for the synthesis of new gold nanoparticles, to be used in optical coatings. The gold nanoparticles were examined with SEM, TEM, DLS, zeta potential, BET, and Vis-NIR for characterising their shapes and sizes, required for determination of the surface plasmon resonance effect. After applying the newly produced gold nanoparticles with fullerene C60 in a combined coating for eyewear lenses, the absorption and transmission of the lenses was determined for establishing changes in the coating functionality. The results show that enhancing the fullerene C60 coating with gold nanoparticles improves light absorption and reflectance for blue and UV light further, which may be evaluated as beneficial for the eyewear user, as the reduction of eye strain is improved due to the coating.

To achieve sustainable development during urbanization, construction waste is recycled for use as an aggregate in recycled concrete (RC). To determine the influence of the brick content in coarse recycled aggregates on the damage sustained by the resultant RC, the RC was first divided into seven phases: natural crushed stone, old gravel inside waste concrete, bricks, new mortar, old mortar on waste concrete surfaces, and new and old interface transition zones. The Monte Carlo method was then applied to establish a two-dimensional random aggregate model of the RC made with coarse brick aggregates. The ABAQUS software package was used to simulate a uniaxial compression test, the results of which were combined with those of a macro-test to determine the internal damage change rule of brick-containing RC. The stress–strain curves obtained from the simulation coincided well with that of the macroscopic tests. As the brick content increased, the damage zone inside the specimen and the number of microcracks increased. The stress concentration area decreased, as indicated by a lower compressive strength in the macro-test. The results indicate that higher brick contents in RC yield more initial damage inside the concrete and a lower compressive strength.

The paper presents an analysis of the possibility of producing traction brushes from waste materials. Brushes are used to ensure good electrical contact between the rail and the pantograph. Slides are produced in the process of hot pressing, with parameters of heating up to max 175 ⁰C, at the minimal pressure value of 200 MPa. The developed brushes with a high (55-60%) content of recycled materials have comparable characteristics to commercial brushes, and some of the prototypes are even more durable and break-resistant.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

In this paper the application of recycled Li-ion batteries spent cathode (LIB-SC) combined with NaHCO₃/H₂O₂ system is presented for the first time in the literature as an alternative for degradation of potentially toxic organic molecules. The model pollutant choice was methylene blue molecule. The spent cathode composition corresponds to LiCoO₂, which was proved by the XRD and EDX. Regarding the decolorization of methylene blue solution, the addition of NaHCO₃ in comparison with only H₂O₂ reduces the complete decolorization time in 96%. This reduction occurs because the radical CO₃ is more stable than OH. In this way, the application the system proposed in this article is aimed at solving two major global problems: the disposal of cell phone batteries and the pollution of liquid effluents.

In the field of construction, materials referred to as sustainable are currently undergoing a process of technological development. This study aims to contribute to the understanding of the behavior of the fundamental properties of concretes prepared with recycled coarse aggregates that incorporate in their matrix a polyethylene terephthalate-based additive in an attempt to reduce their high porosity. Techniques to measure the gas adsorption, water porosity and x-ray diffraction (XRD) were used to evaluate the effect of the additive on the physical, mechanical and microstructural properties of these concretes. Porosity reductions of up to 30.60% are achieved with the addition of 1, 3, 4, 5, 7 and 9% of the additive, defining a new state in the behavioral model of the additive (the overdosage point) in the concrete matrix; in addition, the porous network of these concretes and their correlation whit other physical and mechanical properties are also explained.

Cellulose nanofibrils (CNFs) are materials with high aspect ratio. Typically, TEMPO-oxidised, or cationic CNFs consist of long fibrils (up to 2 μm) with very low thickness (less than 10 nm). Derived from their high aspect ratio, CNFs form strong hydrogels with high elasticity at low concentrations. Thus, CNF suspensions appear as an interesting rheology modifier to be applied in cosmetics, paints, foods, as a mineral suspending agent, among other applications. The high viscosity results from the strong 3D fibril network, which is related to good fibrillation of the material, allowing the nanofibrils to overlap. The overlap concentration (c*) was found to vary from ca. 0.13 to ca. 0.60 wt.% depending on the type and intensity of the pre-treatment ap-plied during the preparation of the CNFs. The results confirm the higher tendency for the fibres treated with CHPTAC (cationic) and TEMPO to form a 3D network, resulting in the lowest c*. For the TEMPO-oxidised CNF suspensions, it was also found that aggregation is improved at acidic pH conditions due to lower charge repulsion among fibrils, leading to an increase in the suspension viscosity, as well as higher apparent yield stresses. TEMPO CNF suspensions with low content of carboxylic groups tend to precipitate at moderate acidic pH values.

This comprehensive review explores recent advancements in heavy metal remediation techniques, focusing on the utilization of cellulose-silica composites and tailored surface modification techniques. We examine the synthesis strategies and properties of cellulose-silica adsorbents, highlighting their enhanced adsorption capacities and structural robustness for removing heavy metal pollutants from aqueous environments. The review investigates various surface modification approaches, including thiol-functionalization, amino acid grafting, and silane coupling agents, for optimizing the surface chemistry and morphology of cellulose-silica composites. Mechanistic insights into the adsorption processes and kinetics of modified adsorbents are discussed, along with considerations for optimizing adsorption performance under different environmental conditions. This review provides valuable perspectives on the development of effective adsorbent materials for sustainable heavy metal remediation applications.

This manuscript investigates the dispersion of cetyltrimethylammonium bromide (CTAB) treated cellulose nanocrystals (CNCs) in polypropylene (PP) by melt mixing. FTIR spectra of CTAB-modified CNCs and unmodified CNCs in a PP matrix were used to evaluate the surface treatments. The surface energies and morphologies of CTAB surface modified CNCs in polypropylene (PP) were used to interpret the effects of nanoparticle dispersion on the crystallization and rheological and mechanical properties of the PP matrix.

The antiradical and antimicrobial activity of lignin and lignin-based films are both of great interest for applications such as food packaging additives. The polyphenol structure of lignin in addition to the presence of O-containing functional groups is potentially responsible for these activities. This study used DPPH assays to discuss the antiradical activity of HPMC/lignin and HPMC/lignin/chitosan films. The scavenging activity (SA) of both binary (HPMC/lignin) and ternary (HPMC/lignin/chitosan) systems was affected by the percentage of the added lignin: the 5% addition showed the highest activity and the 30% addition had the lowest. Both, scavenging activity and antimicrobial activity are depending on the biomass source showing the following trend: organosolv of softwood > Kraft of softwood > organosolv of grass. Testing the antimicrobial activities of lignins and lignin-containing films showed high antimicrobial activities against gram-positive and gram-negative bacteria at 35 °C and at low temperatures (0-7 °C). Purification of kraft lignin has a negative effect on the antimicrobial activity while storage has positive effect. The lignin release in the produced films affected the activity positively and the chitosan addition enhances the activity even more for both gram-positive and gram-negative bacteria. Testing the films against spoilage bacteria that grow at low temperatures revealed the activity of the 30% addition on HPMC/L1 film against both B. thermosphacta and P. fluorescens while L5 was active only against B. thermosphacta. In HPMC/lignin/chitosan films the 5% addition exhibited activity against both B. thermosphacta and P. fluorescens.

The contamination of aquatic environments by pharmaceutical products consistently takes the attention of researchers due to the compounds' toxicity even at low concentrations. In response, we have developed an ecologically sustainable biosurfactant derived from a microorganism and incorporated into the bacterial cellulose. This bioproduct, along with the bacterial cellulose itself, was employed as a sorbent for pharmaceuticals (hormones and paracetamol) present in water. Bacterial cellulose membranes were generated through the cultivation of Gluconacetobacter xylinus ATCC 53582. The biosurfactant was produced by pre-inoculating Bacillus subtilis in a synthetic medium, followed by immersing the bacterial cellulose membranes in the biosurfactant solution, for incorporation. Tests were conducted using water experimentally contaminated with parace-tamol and 17α-ethinylestradiol (EE2), evaluating the biosurfactant's effect on bacterial cellulose sorption. Paracetamol levels were analyzed using spectrophotometry, and EE2 levels were as-sessed using high-performance liquid chromatography. In summary, bacterial cellulose exhibited superior adsorption for EE2 compared to paracetamol. The incorporation of biosurfactant onto bacterial cellulose reduced hormone adsorption but enhanced paracetamol sorption. Our findings indicated that adsorption is more effective with bacterial cellulose in its original and freeze-dried forms, without the incorporation of biosurfactant. Notably, we achieved more promising results in remediating the hormone EE2 compared to the paracetamol.

An enormous interest in the development of efficient protocols for cellulose extraction has been demonstrated in the last years, however, they were usually based on non-sustainable chemical and thermal approaches. In this work we describe a new and more sustainable method for cellulose extraction from eucalyptus and pine tree wood waste products exclusively performed using microwave-assisted radiation. The methodology includes 3 main steps: i) alkaline treatment; ii) bleaching I, using H2O2; and iii) bleaching II, an acidic treatment. Samples obtained in each step were characterized by Fourier-transform Infrared (FTIR) spectroscopy, powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results were compared with those of starting materials, with the commercially available microcrystalline cellulose and with an industrial paper pulp. Results confirmed that for both type of wood wastes, cellulose was retained during the extractions procedures and that the removal of hemicellulose was achieved at the last step as seen by the FTIR spectra and TGA curves. The developed protocol is innovative since it constitutes an easy and quick approach to extract cellulose, from eucalyptus and pine tree wood waste using mild chemical and thermal conditions, microwave irradiation, and environmentally friendly purification steps. This approach offers the possibility of a future scale-up study to potentially apply the develop protocol to the extraction of cellulose in an industrial scale.

Recently, it was reported that the physical cross-linking exhibited by some biopolymers could provide multiple benefits to biomedical applications. In particular, grafting thermoresponsive polymers onto biopolymers may enhance the degradability or offer other features, as ther-mothickening behavior. Thus, different interactions will affect the different hydrogen bonds and interactions from the physical cross-linking of CMC, the lower critical solution temperatures (LCSTs), and the presence of the ions. This work focuses on the study of blends composed of poly(N-isopropylacrylamide), poly(N-ethylacrylamide), and carboxymethyl cellulose in water and water/methanol. The molecular features, the thermoresponsive behavior, and gelation phenomena are deeply studied. The ratio defined by both homopolymers will alter the final properties and the gelation of the final structures, showing that the presence of the hydrophilic groups modifies the number and contributions of the diverse hydrogen bonds.

Increase demand for palm oil production has indirectly increased waste and pollution. Empty fruit bunch (EFB), which is the major solid waste from this industry, has the potential to be further treated into valuable product. In this study, cellulose will be extracted from EFB through alkali treatment and acid hydrolysis treatment with a different approach and further modified via acetylation and silylation technique. The modified samples are to be utilized to reduce pollution due to palm oil mill effluent (POME) and carbon dioxide (CO2) emission from the industry. The characterization of the extracted and modified cellulose was carried out using attenuated total reflectance-Fourier transform infrared (ATR-FTIR), thermogravimetric analysis (TGA) and scanning electron microscope (SEM). ATR-FTIR analysis revealed that the cellulose was successfully extracted from raw EFB and the cellulose-acetyl, nanocrystalline cellulose (NCC) and cellulose-2 has been successfully modified from the cellulose. TGA analysis shows that both modified cellulose have higher thermal stability compared to raw EFB and extracted cellulose. SEM morphology of the modified cellulose shows a higher surface area due to the wrinkled formation while the wax layer and cuticle pore has been diminished clearly. The modified sample gave a significant performance where cellulose-acetyl absorbed 98.5% of oil compared to unmodified cellulose-1 sample that only absorbed 5% of oil from POME. NCC-AEAPDMS adsorbed physically and chemically 3.5 cm3/g CO2 gas compared to NCC sample, which undergoes only physical adsorption with maximum capacity up to 2.4 cm3/g. Thus, modification can enhanced the performance of cellulose for industrial applications.

Polyethylene terephthalate (PET) is nowadays one of the most used polymers for packaging applications. Modifications induced by service conditions and the optimal mean to recycle this matter several times have to be perfectly understood to allow a reuse for similar application (from bottle to bottle for example). The present study aims to compare physico-chemical properties, crystalline organization, and mechanical behaviour of virgin (vPET) and recycled PET (rPET). Using different combined experimental methods (Calorimetry, Small Angle X-ray Scattering, Atomic Force Microscopy, DMA, and uni-axial tensile test), it has been proven that even if there is no change in the crystallinity of PET, the crystallisation process shows some differences (size and number of spherulites). The potential impact of these differences on local mechanical characterization, at the lamella scale, is explored and tends to demonstrate the development of homogeneous microstructure, leading to well-controlled and relevant local mechanical properties. This approach increases the understanding of crystallisation of PET and recycled PET during forming processes such as thermoforming or injection stretch blow moulding (ISBM) where elongation at break can depend on the microstructure conditioned by the crystallisation process.

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

The stability and composting behaviour of monolayers and laminates of poly(lactic acid) (PLA) and starch with and without active extracts and cellulose fibres from rice straw (RS) were evaluated. The retrogradation of the starch throughout storage (1, 5, and 10 weeks) gave rise to stiffer and less extensible monolayers, with lower water vapour barrier capacity. In contrast, the PLA monolayers, with or without extract, did not show marked changes with storage. However, these changes were more attenuated in the bilayers that gained water vapour and oxygen barrier capacity during storage, maintaining the values of the different properties close to the initial range. The bioactivity of the active films exhibited a slight decrease during the storage, the antioxidant capacity being better preserved in the bilayers. All monolayer and bilayer films were fully composted within 90 days, but with different behaviour. The bilayer assembly enhanced the biodegradation of PLA whose monolayer exhibited a lag period of about 35 days. The active extract reduced biodegradation rate of both mono and bilayers but does not limit the material biodegradation within the time stablished in the Standard. Therefore, PLA-starch laminates, with or without the valorised fractions from RS, can be considered as biodegradable and stable materials for food packaging applications.

In this paper, a polyacrylic elastomer latex with butyl acrylate (BA) as the core and methyl methacrylate (MMA) copolymerized with glycidyl methacrylate (GMA) as the shell, named poly(BA-MMA-GMA) (PBMG), was synthesized by seeded emulsion polymerization. Cellulose nanocrystal (CNC) was dispersed in the polyacrylic latex to prepare PBMG/CNC dispersions with different CNC contents. The dried product was mixed with polylactic acid (PLA) to fabricate PLA/PBMG/CNC blends. The addition of PBMG and PBMG/CNC improved the mechanical properties of the PLA matrix. Differential scanning calorimetry (DSC) was used to investigate the non-isothermal crystallization kinetics. The Avrami equation modified by Jeziorny, and the Ozawa, and Mo’s equations were used to analyze the nonisothermal crystallization kinetics of PLA and its blends. Analysis of crystallization halftime of nonisothermal conditions indicated that the overall rate of crystallization increased significantly at 1 wt% content of CNC. This seemed to result from the increase of nucleation density and the acceleration of segment movement in the presence of CNC component. This phenomenon was verified by polarizing microscope observation.

Due to their distinct physical, chemical, and biological characteristics, biopolymers, in particular Poly Ethylene Glycol (PEG) and Cellulose, are frequently used in biomedical medicine as drug or vaccine delivery systems. In this study, we have done a systematic review and a meta-analysis to compare current developments in many PEG and cellulose-based hydrogels, including double network hydrogels, injectable hydrogels, sliding hydrogels, conductive hydrogels, responsive hydrogels, and nanocomposite hydrogels. The pharmacokinetic properties, including physicochemical properties, biocompatibility, biodegradability, temperature, and pH, have been studied as these critical factors are to be considered for deciding the suitability of the drug for delivery. Moreover, the study has evaluated the controlled-release parameters such as half-life, circulation time, maximum release percentage of loaded drug released, burst release, maximum release, and drug-release kinetics. Finally, the efficacy and immune response of hydrogel was studied for future choice, including the cellulose hydrogel system in COVID-related long-term vaccine delivery. The finding revealed that cellulose-based hydrogel is effective for vaccine delivery.

Dentifrice performance in the removal of dental plaque is influenced by the interactions of dentifrice components with tooth surfaces. This randomized controlled clinical study assessed the effectiveness and safety of a novel fluoride dentifrice formulation that included a micro-fibrillated cellulose network with entangled microcrystalline cellulose and silica particles (ProtegeraTM), and compared this to a positive control fluoride dentifrice (Crest Cavity Protection™). Whole mouth dental plaque levels in 82 healthy adults were measured after the first supervised use, and following a week of twice daily use at home. Overall, the novel dentifrice was at least three times more effective in whole mouth plaque reductions than the reference dentifrice (p < 0.001), with a 38.6% reduction on first use, a 30.9% reduction at day 7, and a 41.6% reduction from day 1 to day 7, compared to reductions of 12.0%, 9.6%, and 11.6% respectively for the positive control. No safety issues arose from the use of the novel dentifrice. These results indicate that including micro-fibrillated cellulose enhances plaque removal effectiveness, without causing adverse changes to oral soft tissues.

This experimental study examined the application effect of polycaprolactone (PCL), an organic resin material with excellent elasticity and ductility, on improving the mechanical performance of cellulose nanocrystal (CNC) cement composites. To analyze the effect, a test specimen containing CNC and PCL mixed, containing only CNC, and a control (plain) specimen containing nothing were compared. PCL was compared according to its shape, and in the case of Granules, which is the basic shape, interfacial adhesion with cement was not achieved, so a DCM solution was used to dissolve and use the Granules form. As a method for bonding PCL to the CNC surface, the CNC surface was modified using 3-aminopropyltriethoxysilane (APTES), and surface silylation was confirmed through Fourier transform infrared spectroscopy(FT-IR) analysis. To evaluate the dispersibility according to the application of PCL to the modified CNC, particle size analysis (PSA) and zeta potential analysis were performed according to the PCL mixing amount (0.1, 0.3, 0.5, and 1 vol.% compared with those of CNC) and size distribution. Through the zeta potential value, the highest dispersion stability was shown at 1 vol.%. The cohesive force of CNC was low and the dispersion stability was high according to the application of PCL. According to the results of the dispersion stability evaluation, the degree of hydration of the dissolved PCL 1 vol.%, CNC-only specimens, and plain specimens were analyzed. Hydration products increased by increasing the degree of hydration in the unhydrated area. However, the incorporation of PCL showed a low degree of hydration, and the analysis of strength characteristics also showed a decrease of approximately 27% compared with that of plain specimens. This was because the bonding with SiO2 was not smooth owing to the solvent, thus affecting internal hydration. To investigate the effect of the PCL shape, the compressive and flexural strength characteristics were compared using PCL powder as an additional parameter. The compressive and flexural strength values were improved by approximately 54% and 26%, respectively, compared with those of the plain specimen. Scanning electron microscopy (SEM) analysis determined that the filler effect that made the micropore structure denser, affected the mechanical performance improvement.

This works is related to the modeling of cellulose pyrolysis with a pseudo equilibrium approach. The objective is to model the kinetics of the cellulose pyrolysis with a semi-global mechanism obtained from the literature, in order to obtain the yield and the rate of formation of char. The pseudo equilibrium sense consists in the supposition that the solid phase devolatilization can be described kinetically - at finite rate - , preserving the competitive characteristic between the production of char and tar, while the gas phase can be described by means of chemical equilibrium. A set of ordinary, linear and non linear, differential equations was obtained and solved numerically with a simple but consistent scheme using the Totally Implicit Euler method. Chemical equilibrium was solved using CANTERA coupled with a code written in Matlab. Results showed that the scheme preserve the tar-gas competitive characteristic for cellulose pyrolysis. The gas phase, is defined as a mixture of CO₂, CO, H₂O, CH₄, H₂ and N₂ showed similarly composition compared with models from literature. Finally, the extension of the model to biomass in general, is straightforward, in order to include the hemicellulose and lignin.

A technique for fabrication of bacterial cellulose-based films with CeO₂ nanofiller has been developed. The structural and morphological characteristics of the materials have been studied, their thermal and mechanical properties in dry and swollen states having been determined. The preparation methodology makes it possible to obtain composites with a uniform distribution of nanoparticles. The catalytic effect of ceria regarding the thermal oxidative destruction of cellulose has been confirmed by TGA and DTA methods. An increase in CeO₂ content led to an increase in the elastic modulus (a 1.27-fold increase caused by the introduction of 5 wt.% of the nanofiller into the polymer) and strength of the films. This effect is explained by the formation of additional links between polymer macro-chains via the nanoparticles’ surface. The materials fabricated were characterised by a limited ability to swell in water. Swelling caused a 20- to 30-fold reduction in the stiffness of the material, the mechanical properties of the films in a swollen state remaining germane to their practical use. The application of the composite films in cell engineering as substrates for the stem cells’ proliferation has been studied. The increase in CeO₂ content in the films enhanced the proliferative activity of embryonic mouse stem cells. The cells cultured on the scaffold containing 5 wt.% of ceria demonstrated increased cell survival and migration activity. An analysis of gene expression confirmed improved cultivation conditions on CeO₂-containing scaffolds.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

CMC/PVA composite nanofiber membrane was prepared by electrostatic spinning method, using carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) as raw materials and glutaraldehyde as cross-linking agent. The structure, morphology, thermal stability, and filtration performance of CMC/PVA nanofiber membranes were characterized by advanced instrumental analysis methods such as scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, ultraviolet analysis and energy spectrum analysis. The results show that the average fiber diameter decreases from 381 nm to 183 nm, when the spinning voltage is 23 KV and the jet speed is 2 µL/min. The obtained fiber has the smallest particle size and the most uniform distribution. Infrared spectroscopy analysis confirms that the adsorption behavior of nanofiber membranes on Cu2+ and Cr6+ is chemical adsorption. The retention rates of CMC/PVA nanofiber membranes for Cu2+ and Cr6+ reached 97% and 98%, respectively.

One of the main challenges in the treatment of industrial wastewater is the removal of oil-in-water emulsions, which are stable and therefore difficult to treat. Bacterial cellulose (BC) has structural characteristics that make it an ideal filtration membrane. The present study investigated the effectiveness of a BC membrane filtration system for the treatment of oily industrial wastewaters. The results demonstrated that BC is highly effective at removing oily contaminants (~99%), reducing the colour and particulate matter of wastewater, as well as eliminating nearly the entire microbiological load (~99%). SEM, MEV, FTIR, XRD, and TGA demonstrated the presence of oil in the interior of the membrane after filtration, characteristic peaks of its chemical composition, and a 40% reduction in crystallinity. TGA revealed an increase from three (pre-filtration) to five (post-filtration) stages of thermal degradation, indicating the retention of the contaminant in the BC. The mechanical tests demonstrated that the membrane has tensile strength of 72.13 ± 8.22 MPa and tolerated elongation of up to 21.11 ± 4.81% prior to tearing. The BC membrane also exhibited excellent flexibility, as it could be folded &gt; 100 times at the same point without exhibiting signs of tearing. The BC surpasses traditional methods, such as activated charcoal and effluent treatment stations, in the removal of emulsified oils. The findings demonstrate that BC is promising for the treatment of industrial wastewaters, which is a field that requires continual technological innovations to mitigate the environmental impacts of the oil industry.

Objectives: This study assessed the performance of a novel fluoride dentifrice containing micro- fibrillated cellulose (MFC) and 7% silica (Protegera™) versus common fluoride dentifrices. Methods: Removal of extrinsic stains was assessed using the pellicle cleaning ratio (PCR) method, and radioactive dentin abrasivity (RDA) was measured, to calculate a cleaning efficiency index (CEI). Fluoride efficacy was evaluated using widely used remineralization and fluoride uptake methods. Results: The MFC dentifrice removed stained pellicle significantly more effectively than the ADA reference material, Crest Cavity Protection™ and Sensodyne Pronamel™, and had equal performance to three known marketed stain-removing dentifrices (Arm & Hammer™ Advanced Whitening, Crest ProHealth™, and Colgate Optic White™). The MFC dentifrice vehicle had a low RDA (88), which was significantly less than Crest ProHealth (166) and Crest 3D-White™ (183). Based on PCR and RDA data, the CEI was 31% greater for the MFC product than for Crest ProHealth. In a 10-day pH cycling study, the fluoride efficacy of the MFC product was superior to a non-fluoridated control and was not significantly different from Sensodyne Pronamel and Crest Cavity Protection. The MFC dentifrice was superior for promoting fluoride uptake into incipient enamel lesions than the USP reference dentifrice. Conclusion: The low dentin abrasivity MFC dentifrice is highly effective in removing stained pellicle, and is an efficacious fluoride source when compared to other relevant commercially available fluoride dentifrices with high dentin abrasivity. Clinical Significance: Including micro-fibrillated cellulose into a fluoride dentifrice may enhance cleaning performance for the removal of external stain, while lowering abrasivity, and providing an effective fluoride source. This combination of benefits seems well suited to enamel protection and caries prevention.

The current trends in environment protection and sustainable development demand the investigations in the field of searching new perspective sources for any production. Oat husks seems to be a perspective resource. Cellulose isolated from oat wastes can be used for the production of different materials such as hydro and aerogels, bacterial, nanocrystal and nanofibrillated cellulose, cellulose based composites and ethers. All these materials can be spent in different industries: production of pharmaceuticals, medicine (including targeted delivery of drugs, sponges etc.), agriculture (controlled delivery of pesticides or fertilizers), electronics, production of films, membranes, plastics, coatings, paints, biodegradable packages. In this review, we will demonstrate prospects for using oat husks to obtain cellulose and for obtaining materials based on the main oat husk polysaccharide. This review will evaluate the main achievements in this area. The analysis will allow a reader to form an analytical opinion about the prospects for using oat husks as a source for obtaining valuable products.

Cellulose-based carbon (CBC) has been widely concerned with its porous structure, high specific surface area, and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, ZnO/CBC heterojunction was formed by means of simple co-precipitation and high temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia compared with that of the previous pure ZnO ammonia sensor can not at room temperature. It has great gas sensing response, stability and selectivity to ammonia concentration at 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

Nizatidine is a gastroprotective drug with a short biological half-life and narrow absorption window. This study aimed at developing floating tablets of nizatidine using various HPMC viscosity grades, namely K4M, E4M, K15 and K200M. Directly compressed tablets revealed an excellent uniformity in hardness, thickness and weight and nizatidine was evenly distributed within the matrix floating tablets. Buoyancy study revealed floating lag time as low as 18–38 s, and tablets remain buoyant for upto 24 h. However, the later depended upon viscosity grade of HPMC and that the higher the viscosity, the less was the total floating time. In vitro dissolution indicated viscosity dependent nizatidine release from the floating tablets. HPMC K4M and E4M based floating tablets released almost 100% drug in 12 h, whilst higher viscosity polymers such as K15 and K200M only released 81.88% and 75.81% drug, respectively. The drug release followed non-Fickian diffusion from tablets formulated with K4M, K15 and K200M, whilst super case II transport was observed with E4M based tablets. More interestingly, K4M and E4M polymers have similar viscosity yet exhibited different drug release mechanism. This was attributed to the difference in degree of substitution of methoxyl- and hydroxypropoxyl- groups on polymer backbone.

The enormous potential of renewable bioresources is expected to play a key role in the development of the EU’s sustainable circular economy. In this context, inexhaustible, biodegradable, non-toxic and carbon-neutral forest-origin resources are very attractive for the development of novel sustainable products. The main structural component of wood is cellulose, which, in turn, is the feedstock of nanocellulose, one of the most explored nanomaterials. Different applications of nanocellulose have been proposed, including packaging, functional coatings, insulating materials, nanocomposite fields among others. However, the intrinsic flammability of nanocellulose restricts its use in some industries where fire risk is a concern. This paper overviews the most recent studies of the fire resistance of nanocellulose-based materials, focusing on thin films, coatings and aerogels. Along with effectiveness, increased attention to sustainable approaches is considered in developing novel fire-resistant coatings. The great potential of bio-based fire-resistant materials, combined with conventional non-halogenated fire retardants FRs, has been established. The formulation methods, types of fire retardants and their action modes, and methods used for analysing fire retardancy are discussed in the frame of this overview.

When existing at emulsion interface and continuous phase, dispersibility of water-soluble flexible polymer chains has obvious effect on rheology and dielectric properties of whole emulsion. CNF Pickering emulsion is a good system to research these properties with respect to their microscopic phase structure, dielectric and rheological properties by using cellulose nanofibers (CNF) as water-soluble Pickering emulsifier, liquid Paraffin as oil phase and DDAB as a cationic auxiliary surfactant. The CNF- and DDAB-contents were systematically varied while the water to paraffin oil ratio remained constant to discern the influence of the Pickering emulsifiers. Polarized optical microscopic images revealed that the droplets have tendency to become smaller size for higher CNF content, but bigger size for higher DDAB content, which was proved by the fluorescent analysis for CNF dispersibility with varying DDAB content. The dielectric damping exhibits a minimum, whose value decreases with increasing DDAB- and CNF-content. Increasing the DDAB-content promotes solubilization of CNFs in the aqueous phase and will increase the overall viscosity and yield points. Similarly, a higher CNF-content leads to a higher viscosity and yield point, but at high DDAB-contents the viscosity function exhibits an S-shape at intermediate CNF-content. To evaluate the results further they were compared with CNF-dispersions (without oil-phase), which showed a surfactant effect slightly on maximum stress but strongly on yield stress τy, indicating DDAB can promote the formation of CNF network rather than the viscosity of whole system.

Cationised hemp cellulose was prepared by etherification with two quaternary ammonium salts: 3-chloro-2-hydroxypropyl trimethyl ammonium chloride (CHPTAC) and glycidyltrimethylammonium chloride (GTMAC) and examined for (i) the efficiency of Cr(VI) removal under acid mine-drainage (AMD) conditions, and (ii) antibacterial activity. Adsorbents were characterised by electron microscopy, Fourier transform infrared (FTIR), CP-MAS ¹³C nuclear magnetic resonance (NMR) spectroscopy, elemental composition and surface charge. FTIR and solid state ¹³C NMR confirmed the introduction of quaternary ammonium moieties on cellulose. ¹³C NMR also showed that cationisation decreased the degree of crystallisation and lateral dimensions of cellulose fibrils. Nevertheless, 47 % - 72% of Cr(VI) ions were removed from solutions at pH 4, by 0.1 g of CHPTAC and GTMAC-cationised cellulose, respectively. Adsorption kinetics followed the pseudo-second order model and isotherms were best described by the Freundlich and Dubinin-Radushkevich models. When GTMAC-modified cellulose was applied to AMD contaminated water (pH 2.7), however, Cr(VI) uptake removal decreased to 22% likely due to competition from Al and Fe ions. Nevertheless, cationised materials displayed considerable antibacterial effects, reducing the viability of Escherichia coli by up to 45 % after just 3 hours of exposure. Together, these results suggest that cationised cellulose can be applied in the treatment of Cr(VI)-contaminated mine water particularly if pre-treatments to reduce Fe and Al concentrations are applied.

A new sustainable polypropylene terephthalate (PPT) coating was synthesized from recycled polyethylene terephthalate (PET) and applied on hydraulic concrete substrate to improve its durability. First step, PET bottles wastes were grinded and depolymerized by glycolysis using propylene glycol (PG), in a Vessel-type reactor (20–180 °C) to synthesize bis(2-hydroxypropyl)-terephthalate (BHPT), which was applied as coating to one-three layers on hydraulic concrete substrate, by brushing technique and polymerized (150 °C for 15 h) to obtain PPT. PET, BHPT and PPT were characterized by FT-IR, PET and PPT by TGA, and the PPT coatings by SEM (thickness), by ASTM-D3359-17 (adhesion) and by water contact angle (wettability). The durability of hydraulic concrete coated with PPT was studied by resist chloride ion penetration (ASTM-C1202-17), carbonation depth at 28 days (RILEM-CPC-18), and absorption water ratio (ASTM-C1585-20). The results demonstrated that the BHPT and PPT were synthetized (FT-IR), PPT had a similar thermal behaviour to PET (TGA); the PPT coatings had good adhesion to the substrate, with thicknesses of micrometric units; hydrophilic (similar to PET coatings), and the durability of hydraulic concrete coated with PPT (2-3 layers) improved (migration of chloride ions decreased, carbonation depth was negligible, and the absorption water ratio decreased).

Films obtained from a main biopolymer phase of fish gelatin (GelA, 3% w/w) encapsulated with cinnamon essential oil (CEO, 0.03 – 0.48% v/w) and loaded with bacterial cellulose nanocrystals (BCNCs, 0.06% w/w) at pH = 3.5 were characterized. CEO-GelA/BCNCs films were prepared by casting and analyzed in terms of thickness, light transmittance (TT) and haze (H), surface hydrophobicity, tensile properties, chemical composition, and water solubility (WS). All tested films displayed outstanding optical properties (TT &gt; 89.4%), with haze slightly exceeding a 3% value only when the highest CEO loading was used during nanoemulsion preparation. The CEO plasticizing effect yielded an increase in the elongation at break (EAB, from 0.84% up to 3.79%), which corresponded to a decrease in tensile strength (TS, from 8.98 MPa down to 1.93 MPa). The FT-IR spectra of films revealed a good degree of interaction among single nanoemulsion components via hydrogen bonding. The intrinsic hydrophobic nature of the CEO negatively impacted the WS (from 52.08% down to 8.48%) of the films. Results obtained in this work confirmed the possibility to produce packaging systems from renewable sources to be potentially used in the form of edible films/coatings for preserving water-sensitive food products, both vegan-based (fruits/vegetables), and animal-based (meat/seafood).

Bacterial cellulose (BC) is receiving great attention due to its unique properties such as high purity, water retention capacity, high mechanical strength, and biocompatibility. However, the production of BC has been limited because of high cost and low productivity. In this light, the isolation of new BC producing bacteria and selection of high productive strains became a promising issue. Kombucha tea is a fermented beverage in which the bacteria fraction of the microbial community is composed mostly by strains belonging to the genus Komagataeibacter. In this study Kombucha tea production trials were performed starting from a previous batch, and bacterial isolation was conducted along cultivation time. From the whole microbial pool, 46 isolates were tested for their ability in producing BC. The obtained BC yield ranged from 0.59 g/L, for the isolate K2G36, to 23 g/L for K2G30 used as the reference strain. The genetic intraspecific diversity of the 46 isolates was investigated using two repetitive-sequence-based PCR typing methods, which are the enterobacterial repetitive intergenic consensus (ERIC) elements and the (GTG)5 sequences, respectively. The results obtained using two different approaches revealed the suitability of the fingerprints techniques, showing a discrimination power, calculated as D index, of 0.94 for (GTG)5 rep-PCR and 0.95 for ERIC rep-PCR. In order to improve the sensitivity of the applied method, a combined model from the two genotyping experiments was performed, allowing to discriminate among strains.

Biologic scaffolds have become an attractive approach for repairing the infarcted myocardium and have been shown to facilitate constructive remodeling in injured tissues. This study aimed to investigate the possible utilization of bacterial cellulose membrane patch containing cocultured cells to limit the myocardium's post-infarction pathology. Myocardial infarction was induced by ligating the left anterior descending coronary artery in 45 Wistar rats, and patches with or without cells were attached to the hearts. After one week, the animals underwent echocardiography for assessing ejection fraction and left ventricular end-diastolic and end-systolic volumes. Following the patch formation, cocultured cells retained viability of >90% over 14 days in culture. The patch was applied to the myocardial surface of the infarcted area after staying 14 days in culture. Interestingly, the bacterial cellulose membrane without cellular treatment showed higher preservation of cardiac dimensions; however, we did not observe improvement in the left ventricular ejection fraction of this group compared to coculture treated membranes. Our results demonstrated an important role for bacterial cellulose in supporting cells known to produce cardioprotective soluble factors and may thus provide effective future therapeutic outcomes for patients suffering from ischemic heart disease.

This study aimed to investigate the characteristics of composite scaffolds in combination of fibroin and carboxymethyl cellulose (CMC) in bone tissue engineering. Fibroin is a useful biomaterial and is a major component of silk yarns composed of fibrous proteins. Improving for binding efficiency in bone formation after implanted scaffold, CMC was added to fibroin. CMC could improve injectable characters in bone substitutes by adding in scaffold material, fibroin. The porous shapes, porosity, surface wettability, water absorption, and thermal properties of the CMC added fibroin scaffold were better than fibroin only scaffold. For tissue engineering of bone marrow mesenchymal stem cells (BMSCs), BMSCs isolated from mice were seeded onto the scaffold, and the cell proliferation rate was measured. alkaline phosphatase activity in BMSCs was higher in the scaffold containing CMC than that in the scaffold containing fibroin alone. The expression levels of osteocyte marker genes and proteins were increased in the CMC scaffold. The biocompatibility and hydrophilicity of CMC scaffolds play important roles in the growth and proliferation of osteocytes. Furthermore, the CMC scaffold design proposed in this study could play an important role in facilitating cartilage, ossification, and nerve differentiation of BMSCs.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.

Mining-induced water contamination remains a significant concern in many regions of the world due to the high concentrations of toxic ions often associated with it. In this study, cellulose-supported ferrihydrite composites (CNF-Fe) were prepared by seeding of ferrihydrite nanoparticles on cellulose nanofibres (CNFs) and employed for the removal of As(III), As(V) and Cr(VI) from contaminated water. The adsorbent was characterized by electron microscopy, gas adsorption, point of zero charge (pH_PZC), X-ray diffractometry (XRD), as well as infrared and Raman spectroscopy. Compared to parent CNFs, CNF-Fe adsorbents had lower crystallinity and a higher surface area: 218.76 m² g^-1. Further, with a pH_PZC of 6.3, CNF-Fe was positively charged at low pH and suitable for adsorption of anions at acidic conditions characteristic of acid mine drainage. In single-ions solutions, the removal efficiency of CNF-Fe was in the order Cr(VI)>As(V)>As(III) (i.e. 0.15, 0.12 and 0.11 mg g^-1 respectively). Adsorption kinetics followed the pseudo second-order model and isotherms were best fitted by the Freundlich, Dubinin-Radushkevich, and Temkin models. However, when CNF-Fe was applied to AMD-contaminated water (pH 2.7), Cr(VI) uptake decreased to ~39% which was likely due to competition from sulphate and selenium ions. Nevertheless, the adsorbent displayed regeneration capabilities with ~98% As and ~45% Cr desorbed after 24 hours of treatment. Together, these results suggest that cellulose supported ferrihydrite composites can be applied in treatment of mine drainage-contaminated water in conjunction with pre-treatments that limit SO₄^2- and selenium concentrations.