In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

In this study, we investigated the features of co-infection with SARS-CoV-2 and nonpathogenic strain LEV8 of coxsackievirus A7 or enterovirus A71 for Vero E6 cells and Syrian hamsters. The investigation of co-infection with SARS-СoV-2 and LEV-8 or EV-A71 in the cell model was shown that a competitive inhibitory effect for these viruses were especially significant against SARS-CoV-2. Pre-infection with enteroviruses in animals caused more than a 100-fold decrease in the levels of SARS-CoV-2 virus replication in the respiratory tracts and more rapid clearance of the lower respiratory tract from infectious SARS-CoV-2. Co-infection with SARS-CoV-2 and LEV-8 or EV-A71 also reduced the severity of clinical manifestations of the SARS-CoV-2 infection for animals. Additionally, the histological data illustrated that co-infection with nonpathogenic coxsackievirus decreased the level of pathological changes by SARS-CoV-2 in the lungs. Research into the chemokine/cytokine profile demonstrated that the studied enteroviruses efficiently triggered this part of antiviral immune response, which can be associated with significant inhibition of SARS-CoV-2 infection. These results demonstrate that there exists a strong viral interference between the studied nonpathogenic strain of coxsackievirus A7 or enteroviruses A71 and SARS-CoV-2 pathogenic for humans in vitro and in vivo.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Primary ciliary dyskinesia (PCD) is an inherited disorder that impairs motile cilia, essential for respiratory health, with a reported prevalence of 1 in 16,309 within Hispanic populations. Despite having the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in 70% of Puerto Rican patients, the characterization of the ciliary dysfunction remains unidentified due to the unavailability of advanced diagnostic modalities like High-Speed Video Microscopy Analysis (HSVA). Our study implemented HSVA for the first time on the island as a tool to better diagnose and characterize the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in Puerto Rican patients. By applying HSVA, we analyzed the ciliary beat frequency (CBF) and pattern (CBP) in native Puerto Rican patients with PCD. Our results showed decreased CBF and a rotational CBP linked to the RSPH4A founder mutation in Puerto Ricans, presenting a novel diagnostic marker that could be implemented as an axillary test into the PCD diagnosis algorithm in Puerto Rico. The integration of HSVA technology in Puerto Rico substantially enhances the framework for PCD evaluation and diagnosis, facilitating prompt detection and early intervention for improved disease management. This initiative, demonstrating the potential of HSVA as an adjunctive test within the PCD diagnostic algorithm, could serve as a blueprint for analogous developments throughout Latin America.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

Optical artificial neural networks (ONNs) — analog computing hardware tailored for machine learning [1,2] — have significant potential for ultra-high computing speed and energy efficiency [3]. We propose a new approach to architectures for ONNs based on integrated Kerr micro-comb sources [4] that is programmable, highly scalable and capable of reaching ultra-high speeds. We experimentally demonstrate the building block of the ONN — a single neuron perceptron — by mapping synapses onto 49 wavelengths of a micro-comb to achieve a high single-unit throughput of 11.9 Giga-FLOPS at 8 bits per FLOP, corresponding to 95.2 Gbps. We test the perceptron on simple standard benchmark datasets — handwritten-digit recognition and cancer-cell detection — achieving over 90% and 85% accuracy, respectively. This performance is a direct result of the record small wavelength spacing (49GHz) for a coherent integrated microcomb source, which results in an unprecedented number of wavelengths for neuromorphic optics. Finally, we propose an approach to scaling the perceptron to a deep learning network using the same single micro-comb device and standard off-the-shelf telecommunications technology, for high-throughput operation involving full matrix multiplication for applications such as real-time massive data processing for unmanned vehicle and aircraft tracking.

With the progression of AI, embedding advanced AI technologies into small robotics and mobile devices has become essential, driving research towards lightweighting AI models. Our study enhances the EPINET depth estimation model for light field images, aiming for compactness and faster inference while preserving accuracy. We conducted two-step experiments aimed at enhancing inference efficiency: Initially, by adjusting input streams and convolution layers, we simplified the CNN model, achieving faster inference times at the cost of reduced accuracy. To address this reduction in accuracy, we then applied knowledge distillation, allowing the simplified model to learn from the original model’s more complex patterns. In our quantitative experiments using two error metrics, MSE (Mean Squared Error) and BadPix, we identified optimal knowledge positions and evaluated the required complexity for the student model. As a result, our method improved MSE by 21% and BadPix by 14% compared to training without it. Furthermore, the student model achieved an inference speed 13% faster than the teacher model and surpassed its accuracy by 10% in MSE. Additionally, we demonstrated that repeatedly applying our approach could further enhance both model compactness and accuracy.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

In this paper, the effect of multi-pass friction stir processing on the mechanical properties of AZ91 alloy has been studied. For the numerical investigation, this process has been simulated with the three-dimensional numerical modeling based on the ABAQUS/Explicit. This simulation involves the Johnson-Cook models for defining the material behavior during this intense plastic deformation and investigating the fracture criterion. The tool plunging and stirring phases in the two-pass process has been simulated. To prevent too much distortion of elements during modeling, the Arbitrary Lagrangian-Eulerian technique for automatically re-meshing of distorted elements has been used. The model was calibrated using the experimental results from the previous works. This model can predict the transient temperature distribution and residual stress field during FSP on AZ91. The results show that the maximum temperature in the advancing-side region is more than that in the retreating-side region. In addition, numerical results show that at the end position of the process, the tool during the lift-up leaves the keyhole region in the compressive stress state. The experimental results investigated the effect of multi-pass FSP on the microstructure, microhardness, tensile and creep properties of AZ91 magnesium alloy. The FSP is performed by applying 50% overlapping. The tensile, and creep tests are conducted at several temperatures from 25 to 210 °C. The optical microscopy and scanning electron micrograph (SEM) were used to study the microstructure of the samples after performing multi-pass friction stir processing. The experimental results indicate that on average, the tensile strength, microhardness, and creep strength of the processed samples increased by about 29, 23, and 38 %, respectively compared to the unprocessed ones.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Warming of the climate system is unequivocal, and many of the observed changes are unprecedented over five decades to millennia. Globally the atmosphere and ocean is increasingly getting warmer, the amount of ice on the earth is decreasing over the oceans, and the sea level has risen. According to Intergovernmental Panel on Climate Change, the total increasing temperature globally averaged combined land and surface between the average of the 1850-1900 period and the 2003 to 2012 period is 0.78 °C (0.72 to 0.85). But should we prepare for such the relatively small change? The importance is not the mean of the warming but the considerable likelihood of climate change that could trigger extreme natural hazards. The impact and the risk of climate change associated with railway infrastructure have not been fully addressed in the literature due to the difference in local environmental parameters. On the other hand, the current railway network in Malaysia, over the last decade, has been significantly affected by severe weather conditions such as rainfall, lightning, wind and very high temperatures. Our research findings point out the extremes that can lead to asset system failure, degraded operation and ultimately, delays to train services. During the period of flood, the embankment of the track can be swept away and bridge can be demolished, while during drought, the embankment of the track can suffer from soil desiccation and embankment deterioration, high temperature increases the risk of track buckling and high winds can result in vegetation or foreign object incursion on to the infrastructure as well as additional quasi-static burden exerted. This review is of significant importance for planning and design of the newly proposed high speed rail link between Malaysia and Singapore.

This paper reports on the optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation systems for cattle farming in rural areas of Bangladesh. Bangladesh is a lower middle-income country with declining rates of poverty among its 160 million people due to persistent economic growth in conjunction with balanced agricultural improvements. Most of the rural households adopt a mixed farming system by cultivating crops and simultaneously rearing livestock. Among the animals raised, cattle are considered as the most valuable asset for the small/medium-scale farmers in terms of their meat and milk production. Currently, along with the major health issue, the COVID-19 pandemic is hindering the world’s economic growth and has thrust millions into unemployment; Bangladesh is also in this loop. However, natural disasters such as COVID-19 pandemic and floods, largely constrain rural smallholder cattle farmers from climbing out of their poverty. In particular, small and medium-scale cattle farmers face many issues that obstruct them from taking advantage of market opportunities and imposing a greater burden on their families and incomes. An appropriate measure can give a way to make those cattle farmers’ businesses both profitable and sustainable. Optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation system for cattle farming is a new and forward-looking approach for sustainable development of the livestock sector. In this study, we design and optimize a thin-film coating assisted hybrid (photovoltaic-battery-generator) power system by using the Hybrid Optimization of Multiple Energy Resources (HOMER, Version 3.14.0) simulation tool. An analysis of the results has suggested that the off-grid hybrid system is more feasible for small and medium-scale cattle farming systems with long-term sustainability to overcome the significant challenges faced by smallholder cattle farmers in Bangladesh.

Background: Music evokes positive emotions and reduces stress and anxiety. Operating Room (OR) staff face various challenges which can lead to high levels of stress. The aim of the study is to assess whether listening to music during intraoperative phases improves the work environment by reducing anxiety and stress in the entire surgical team. Methods. A prospective observational study was conducted from February to September 2023, involving medical personnel, nursing staff, and nursing students. They were divided into two groups: Group 1 with music during surgical procedures, and Group 2 without music. Participants were administered two validated instruments: the Zung Anxiety Self-Assessment Scale (SAS) to measure anxiety, and the Positive and Negative Affect Schedule to assess emotions generating stress. Additional items were included for demographics, job satisfaction, and the organization method. Results. Music did not impact anxiety but increased positive emotions while reducing negative ones. Music had an ancillary effect, highlighting the need for significant organizational interventions aimed at increasing operator satisfaction, including voluntary rather than mandatory assignments for nursing staff. Conclusions. Music appears to reduce stress in the intraoperative team when supported by a positive work environment in which assigned operators have chosen to work in the OR.

This research explores the intricate relationship between gravitational and cosmic redshift phenomena, unveiling a profound understanding of how light behaves as it traverses the cosmos. The study begins with an examination of gravitational redshift, a well-established concept occurring when photons move away from massive gravitational sources, such as stars within galaxies. Gravitational redshift, expressed as λ/λ₀, manifests within the gravitational influence and extends to the boundary of the observed "zero-gravity sphere" enveloping galaxies. Within this remarkable zero-gravity sphere, gravitational effects persist, while the antigravity influence of dark energy remains negligible. As a result, gravitational redshift dominates, and cosmic redshift is notably absent within the sphere. Photons within this sphere maintain their constant speed 'c' and undergo gravitational redshift exclusively. However, as photons exit the zero-gravity sphere at a distance 'r' equivalent to the source star's radius, they encounter the onset of cosmic redshift, quantified as {(λ_obs - λ_emit)/ λ_emit}. Cosmic redshift blends with gravitational redshift, forming the effective redshift of the photon. Critically, the effective cosmic redshift surpasses gravitational redshift, illuminating a profound revelation: photons traverse a greater "light-traveled distance" than their proper distance from the source. In essence, cosmic redshift signifies that photons move across their intended distances at their intrinsic speed c, while the expanding universe introduces a relative distance expansion, influenced by antigravity. This research delves into the intricate dance between gravitational and cosmic redshift, shedding light on their remarkable implications for our comprehension of the expanding universe.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

The aim of this study was to evaluate the acceptability and feasibility of a theory-derived sedentary workplace intervention (single arm, pre-post design) for police office staff. Twenty-four staff participated in an 8-week intervention incorporating an education session, team competition with quick response (QR) codes, team trophy, and weekly leaderboard newsletters, a self-monitoring phone app, and electronic prompt tools. The intervention supported participants to reduce and break up their sitting time with three minutes of incidental movement every 30 minutes at work. Feasibility and acceptability were assessed using mixed methods via the RE-AIM QuEST and PRECIS-2 frameworks. The intervention was highly pragmatic in terms of eligibility, organisation, adherence, outcome, and analysis. It was slightly less pragmatic on recruitment and setting. Delivery and follow-up were more explanatory. Reach and adoption indicators demonstrated feasibility among police staff, across a range of departments, who were demographically similar to participants in previous office-based multi-component interventions. The intervention was delivered mostly as planned with minor deviations from protocol (Implementation fidelity). Participants perceived the intervention components as highly acceptable. Preliminary results showed improvements in workplace sitting and standing, as well as small improvements in weight and positive affect. Evaluation of the intervention in a fully powered randomised controlled trial to assess behaviour and health outcomes is recommended.

: One of the challenges facing operations management is the design, choice and imple-mentation of action plans adapted to the magnitude of the deviations of the variables of an industrial process. Making conscious and quick decisions is crucial to achieving im-provements in productivity. This will be achieved if the organization's internal and external communication model is strategically designed, considering specific cultural factors and the symmetry or asymmetry required in the communication model. However, how do we organize ourselves and through what channels do we communicate within a production process to generate Big Data that combines data from technologies and the perception, comprehension and projection of experienced humans? Our purpose is to create an operations management model that facilitates the incorporation of technology, allows a prompt response to failures, and promotes the sustainability of processes, without losing sight of its alignment with the organizational strategy. The developed model was implemented in an operations management team, following the guidelines of an action researcher methodology. This resulted in the design of an operations management model and a detailed methodology for its implementation, achieving sig-nificant improvements in the metrics of the current process, making it a success story.

Inflammatory bowel diseases (IBD) includes Crohn's disease and ulcerative colitis, are idiopathic chronic relapsing inflammatory disorders of the intestinal tract. Different studies indicate that phytocanna-binoids, could play a possible role in the treatment of IBD by relieving the symptoms involved in the dis-ease. Phytocannabinoids act through the endocannabinoid system, which is distributed throughout the mammalian body in the cells of the immune system and in the intestinal cells. Our in vitro study analyzed the putative-anti-inflammatory effect of nine-selected pure cannabinoids in J774A1 macrophages cells and enteric glial cells (EGC’s) triggered to undergo inflammation with lipopolysaccharide (LPS). The an-ti-inflammatory effect of several phytocannabinoids was measured by their ability to reduce TNF tran-scription and translation in J774A1 macrophages and to diminish S100B and GFAP secretion and tran-scription in EGC’s. Our results demonstrate that THC at the lower concentrations tested exerted the most effective anti- inflammatory effect in both J774A1 macrophages and EGC’s compared to the other phy-tocannabinoids tested herein. We then performed RNA-seq analysis of EGC’s exposed to LPS in the presence or absence of THC or THC-COOH. Transcriptomic analysis of these EGC’s revealed 23 differ-entially expressed genes (DEG) compared to treatment with only LPS. Pretreatment with THC resulted in 26 DEG and pretreatment with THC-COOH resulted in 25 DEG. To evaluate which biological pathways were affected by the different phytocannabinoid treatments we used the Ingenuity platform. We show that THC treatment affected the mTOR and RAR signaling pathway while THC-COOH affected mainly the IL6 signaling pathway.

Studies show that although female soccer players often have shorter change of direction (COD) deficits than males, indicating different biomechanical profiles, there is lack of research on the impact of physical metrics on COD performance in females. The aim of this study was to analyze whether performance metrics based on speed, and jumping could explain the variation in %CODD in young female soccer players. Thirty-three highly trained adolescent female soccer players (age: 16. ± 0.95 years; height: 160.4 ± 5.22 cm; body mass: 55.7 ± 7.22 kg) performed COD180 tests, 10-m and 30-m sprint test and single leg countermovement and horizontal jumps. Acceleration in the first 10 meters of a sprint was identified as a significant predictor of COD180 performance (R2 = 28%), (R2 = 50%), (p

Play therapy is an approach to providing assistance in overcoming problems using media such as toys, art media, games, and communication. The purpose of this paper is to find out that play therapy can reduce anxiety in children. The research design used in this study was a study-literature review. The data used in this research comes from the results of research that have been conducted and published in national and international online journals. The method of analysis used in this study is the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analysis) method.

As one of the fastest-growing new energy sources, wind power technology has attracted widespread attention from all over the world. In order to improve the quality of wind power generation, wind speed prediction is an indispensable task. In this paper, an error correction based Variational Mode Decomposition and Broad Learning System (VMD-BLS) hybrid model is proposed for wind speed prediction. First, the wind speed is decomposed into multiple components by the VMD algorithm, and then an ARMA model is established for each component to find the optimal number of sequence divisions. Second, the BLS model is used to predict each component, and the prediction results are summed to obtain the wind speed forecast value. However, in some traditional methods, there is always time lag, which will reduce the forecast accuracy. To deal with this, a novel error correction technique is developed by utilizing BLS. Through verification experiment with actual data, it proves that the proposed method can reduce the phenomenon of prediction lag, and can achieve higher prediction accuracy than traditional approaches, which shows our method’s effectiveness in practice.

An axiomatic theory is proposed that reconciles the existence of an absolute scale for time (Planck time) and special relativity. According to this theory speed of light c becomes a variable which is proposed to be taken as the fifth dimension.

Based on four major cosmological and astrophysical coincidences, it seems possible to develop a new model of Hubble-Hawking Universe having light speed expansion. Considering the analysis of 740 super novae data, it is possible to consider a constant rate of cosmic expansion. As there is no physical reasoning for the observed speed of light and all the cosmological observations are completely based on speed of light-by considering ‘light speed expansion’ as a characteristic nature of the universe, big bang, inflation, dark energy, quintessence and lambda term like ideal and unidentified concepts can be reviewed and relinquished at fundamental level and a practical model of expanding universe can be developed with ease and clarity. In this context, we would like to emphasize the point that, traditional definition of cosmic red shift is absolutely wrong. In terms of energy of photon, true cosmic red shift must be defined as - ratio of loss of energy in photon to the energy of photon at galaxy. We encourage the reader to see Figure 1 and Table 1 pertaining to light travel distances prepared with $\left(\frac{z}{1+z}\right)\left(\frac{c}{H_0}\right)\cong z_{new}\left(\frac{c}{H_0}\right)$. For data comparison, readers are encouraged to visit https://cosmocalc.icrar.org/ and http://www.atlasoftheuniverse.com/cosmodis.c. It may be noted that, considering 200 million solar masses as a cut off for ordinary gravity, dark matter can be considered as an effect of power law based super gravity of galactic baryonic mass. It is well believed that, Hawking’s findings about black holes are the most important contributions to physics in recent decades. Hence, we appeal the science community to recommend our Hubble-Hawking model for further research and study.

Soybean a pulse of considerable nutritional value due to its high protein, fibers and polyunsaturated fatty acid (PUFA) contents, also contains phytoestrogenic compounds that definitely hinder its recommendation for general consumption. Contrarily to ancient times when soybeans were boiled, modern commercial soy-foods can contain up to 150 mg/100g of estrogenic isoflavones. Interestingly, current estimations of isoflavone intake in the literature do not distinguish between the origins of soy-food i.e. home-made or commercial. As a result, the isoflavone exposure in Asian countries may well be over-estimated. This study aims to demonstrate, based on step-by-step monitoring of isoflavones, that traditional and domestic treatments, leveraging isoflavones water-solubility, can indeed significantly reduce their content in soy-foods. Indeed, when compared to commercial foods, the isoflavone contents was found to be 20, 2.6, 4.5 and 9.8 times lower in “home-made” soy-juice, tofu, tempeh and miso, respectively. Additionally, water soaking was found to reduce the isoflavones levels in soy-textured-proteins by more than 70%. Hence, this simple process has the potential to help drastically reduce overall xenoestrogens exposure. This study could serve as a basis for establishing the isoflavones Reference Dose and issuing food safety guidelines.

The is a sequential article to an initial review suggesting that Microbiome First medical approaches to human health and wellness could both aid the fight against noncommunicable diseases and conditions (NCDs) and help to usher in sustainable healthcare. This current review article specifically focuses on public health programs and initiatives and what has been termed by medical journals as a catastrophic record of recent failures. Included in the review is a discussion of the four priority behavioral modifications (food choices, cessation of two drugs of abuse, and exercise) advocated by the World Health Organization as the way to stop the ongoing NCD epidemic. The lack of public health focus on the majority of cells and genes in the human superorganism, the microbiome, is highlighted as is the “regulatory gap” failure to protect humans, particularly the young, from a series of mass population toxic exposures (e.g., asbestos, trichloroethylene, dioxin, polychlorinated biphenyls, triclosan, bisphenol A and other plasticizers, polyfluorinated compounds, herbicides, food emulsifiers, high fructose corn syrup, certain nanoparticles, endocrine disruptors, obesogens). The combination of early life toxicity for the microbiome and connected human physiological systems (e.g., immune, neurological), plus a lack of attention to the importance of microbial rebiosis has facilitated rather than suppressed, the NCD epidemic. This review article concludes with a call to place the microbiome first and foremost in public health initiatives as a way to both rescue public health effectiveness and reduce the human suffering connected to co-morbid NCDs.

Speeding is a significant global issue, with disparities in speed outcome and speed research between low- and middle-income countries (LMICs) and high-income countries (HICs). This study aims to address speed research gaps by examining the prevalence of self-reported speeding and factors influencing drivers' speeding behavior (SB) using the Theory of Planned Behavior (TPB). An online survey involving 387 anonymous drivers was conducted in Yaoundé. Results showed that all drivers reported exceeding speed limits, with 81% exceeding by 5km/h, 12% by 10km/h, and 7% by more than 10km/h in urban areas. On highways, 54% reported exceeded the limit by more than 10km/h. Age, driver's license, and gender showed significant associations with speed limits non-compliance. The study results suggests that the TPB can be useful in assessing speeding behavior, as the inclusion of TPB variables led to a more than 50% proportionate increase in SB variance. Structural equation modeling revealed attitude towards speeding as the strongest predictor of speeding intention (SI), along with certain demographics indirectly influencing SB through SI. Perceived behavioral control (PBC) and SI directly influenced SB. These findings emphasize the potential of interventions targeting attitude, intentions, and perceived behavioral control to modify speeding behavior and improve road safety.

Player’s performance in an intense sport such as basketball is known to be related to attributes like speed, agility, and power. This study presents a comparative analysis of associations between anthropometric assessment and physical performance in different age-group elite youth basketball players, while simultaneously identifying the predictors for speed and agility in these players. U14 (n=44), U15 (n=45) and U16 (n=51) players were tested for anthropometry, lower body power, speed, and agility. U16 players were found to be taller, heavier, more muscular than U14 and U15 players. Also, the U16 group showed better performance in all performance tests. Age had a significant positive correlation with countermovement (CMJ) and drop jump (DJ) performance in U14 players, and a significant negative correlation with 10m and 20m sprint times in U15 group. CMJ and DJ emerged as the most significant predictors for sprint and agility variables, respectively. Body fat percentage was found to be a significant predictor for the speed and agility tests in all age groups, but a negative lower-body power predictor. Therefore, besides all sport-specific and fitness tests, it is essential to place emphasis on the percentage of body fat when designing players’ individualized training programs, and during team selection.

pump as turbine (PAT); computational fluid dynamics; variable rotational nominal speed; OpenFoam.

Vibration suppression in a field of frequencies and the creation of band gaps which do not allow the propagation of the waves is studied in this paper by means of microstructures designed through topology optimization. Topology optimization is formulated in frequency domain. Band gap design is based on Floquet-Bloch theory and genetic optimization. The result is appealing in view of modern 3D printing techniques.

1) We shall discuss what modern interpretations say about the Heisenberg's uncertainties. These interpretations explain that a quantity begins to 'lose' meaning when a conjugate property begins to 'acquire' definite meaning. We know that a quantity losing meaning means that it has no fixed value and has an uncertainty . In this paper we look deeper into this interpretation and the outcome reveals more evidence of the quantity losing meaning. Newer insights appear. 2) We consider two extreme cases of hypothetical processes nature undergoes, without interference by a measurement: One, a system collapses to an energy eigenstate under the influence of a Hamiltonian instantaneously at a time $t$. This is thus what would happen if we would measure the system's energy. Next, when a particle becomes localised to a point at a time $t_0$ under the influence of a Hamiltonian. This is thus what would happen if we would measure the system's position. We shall prove that both these situations cannot arise under ordinary circumstances and thus measurement processes cannot be modelled by physical Hamiltonians.

The methamphetamine epidemic continues to worsen each year and has contributed to more overdose deaths than opioids. Methamphetamine was listed in the top ten lethal drugs in 2021 in the United States. The drug has been shown to cause many health problems. One solution to this crisis is through vaccinations. Although still early in the development phase, vaccinations have been found to improve withdrawal symptoms and decrease drug seeking behavior with minimal health side effects compared to medications.

It has been suggested that particle size plays an important role in determining the genotoxicity of gold nanoparticles (GNPs). The purpose of this study was to compare the potential radio-sensitization effects of two different sized GNPs (3.9 and 37.4 nm) fabricated and examined in vitro in Lewis Lung carcinoma (LLC) as a model of non-small cell lung cancer through use of comet and clonogenic assays. After the treatment of 2Gy X-ray irradiation, both particle sizes demonstrated increased DNA damage when compared to treatment with particles only and radiation alone. This radio-sensitization was further translated into a reduction in cell survival demonstrated by clonogenicity. This work indicates that GNPs of both sizes induce DNA damage in LLC cells at the tested concentrations, whereas the 37.4 nm particle size treatment group demonstrated greater significance in vitro. The presented data aids in the evaluation of the radiobiological response of Lewis Lung carcinoma cells treated with gold nanoparticles.

In the last century, statistical process control has been considered a successful methodology for monitoring the variability and stability of a process over time. The analysis of variability using functional data analysis has become widespread during the early years of the 21st century. The present study proposes the implementation of a hybrid methodology called functional process control based on the functional data analysis methodology and combines its advantages with those of statistical process control, in order to provide a tool for detecting functional deviations. The phases are: (1) stabilization of processes through the identification and elimination of special causes of functional variability; (2) improvement of the process to be controlled by minimizing the common causes of functional variability; and (3) monitoring of the processes to ensure the maintenance or addition of further improvements.

In central Senegal malaria incidences have declined from 2000 to 2010 in response to scaling-up of control measures and then remained stable, making elimination improbable. Additional control measures are needed to reduce transmission. We simulated chemoprophylaxis interventions targeting malaria hotspots, using a meta-population mathematical model based on differential equation framework and incorporating human mobility. The model was fitted to weekly malaria incidences from 45 villages. Three approaches for selecting intervention targets were compared: a) villages with malaria cases during the low transmission season of the previous year; b) villages with highest incidences during the high transmission season of the previous year; c) villages with highest connectivity with adjacent populations. Our modeling, considering human mobility, showed that the intervention strategies targeting hotspots would be effective in reducing malaria incidence in both targeted and untargeted areas. But whatever the intervention, pre-elimination stage (1-5 cases per 1,000 per year) would not be reached without simultaneously increasing vector control by more than 10%. Targeted interventions allow increasing overall malaria control and elimination potential.

The current COVID-19 pandemic is one of the most devastating events in recent history. The virus causes relatively minor damage to young, healthy populations, imposing life-threatening danger to the elderly and people with diseases of chronic inflammation. Therefore, if we could reduce the risk for vulnerable populations, it would make the COVID-19 pandemic more similar to other typical outbreaks. Children don’t suffer from COVID-19 as much as their grandparents and have a much higher melatonin level. Bats are nocturnal animals possessing high levels of melatonin, which may contribute to their high anti-viral resistance. Viruses induce an explosion of inflammatory cytokines and reactive oxygen species, and melatonin is the best natural antioxidant that is lost with age. The programmed cell death coronaviruses cause, which can result in significant lung damage, is also inhibited by melatonin. Coronavirus causes inflammation in the lungs which requires inflammasome activity. Melatonin blocks these inflammasomes. General immunity is impaired by anxiety and sleep deprivation. Melatonin improves sleep habits, reduces anxiety and stimulates immunity. Fibrosis may be the most dangerous complication after COVID-19. Melatonin is known to prevent fibrosis. Mechanical ventilation may be necessary but yet imposes risks due to oxidative stress, which can be reduced by melatonin. Thus, by using the safe over-the-counter drug melatonin, we may be immediately able to prevent the development of severe disease symptoms in coronavirus patients, reduce the severity of their symptoms, and/or reduce the immuno-pathology of coronavirus infection on patients’ health after the active phase of the infection is over.

I demonstrate that the macrocosmic gravitational interaction between two masses and the microcosmic electrostatic interaction between two charges unify in simple concepts and mathematical laws when electric charge and ordinary mass are interpreted in reciprocal terms. No previous research has ever attempted to unify charge and mass. The difficulty has been lack of an intelligible definition of charge. A three-point paradigm shift solves the problem, giving convincing evidence – for the first time – that positron and negatron are the ultimate elementary particles. That is, matter is pure positive and negative grains of electricity. Paradigm shift #1: Electron is a moving charge; a charge is static electron – ‘one entity two identities’. This implies that ordinary matter contains equal numbers of positive and negative electrons – observed in motion as ‘electrons’ and at rest as ‘charges’. In motion, a positron-negatron pair obeys the laws of electrodynamics and annihilates; at rest, the pair obeys the laws of electrostatics and neutralizes. Paradigm shift #2: Electron mass and electrostatic field are either positive or negative. Opposite masses and fields, rather than indefinable ‘charge’, make opposite electrons physically different. Paradigm shift #3: Electric charge and ordinary mass interconvert. Positive charge (e⁺) and negative charge (e^-) neutralize to neutral charge (2e⁰), which is nature’s quantum of ordinary mass. Conversely, a quantum of ordinary mass splits to opposite charges e.g. in frictional electrification. The insights systematize the search, identification and classification of ‘elementary particles’, ending decades of confusion in the ‘elementary particle zoo’. They identify a new, stable subatomic particle – a third nucleon.

Background. False memories tend to increase in healthy and pathological aging, and their reduction could be useful in improving cognitive functioning. The objective was to use an active-placebo method to verify whether the application of tDCS in improving true recognition and reducing false memories in healthy older people. Method. Participants were 29 healthy older adults (65-78 years old) assigned to active or placebo group; active group received anodal stimulation at 2mA for 20 min over F7. An experimental task was used to estimate true and false recognition. The procedure took place in two sessions on two consecutive days. Results. A mixed ANOVA of true recognition showed a significant main effect of session (p = .004), indicating an increase from before treatment to after it. False recognition showed a significant main effect (p = .004), indicating a decrease from before treatment to after it and a significant session x group interaction (p < .0001). Conclusions. Overall, our results show that tDCS is an effective tool for increasing true recognition and reducing false recognition in healthy older people, and suggest that stimulation improves recall by increasing the number of items a participant can recall and reducing the number of memory errors.

With an increasing demand for quality of care and lower costs, hospitals are looking for industry-based methods to improve efficiency in their processes. This study aims to reduce waste in a public hospital in Mexico by improving the medical supply process for the operating room. To this end, a lean healthcare (LH) implementation following the DMAIC approach (Define-Measure-Analyze-Improve-Control) is carried out. We analyze the value stream of the supply process, including main surgical procedures and their related medical supplies, and identify different causes of inefficiency, which are evaluated and controlled through different tools, including a value stream map, Kanban, and the 5S program. As a result, five types of waste were reduced. Over-processing requests were reduced by 15.3%, defective identification numbers were reduced by 46.5%, redundant processing was improved by 94.8%, near 2.8% of the unnecessary inventory was reduced, and transportation waste was reduced by up to 16.7%. Finally, the lead-time for the main supplies was reduced by 33 days. This work demonstrates that LH and DMAIC are effective in reducing waste and are highly conducive to improving sustainability in healthcare processes. Moreover, it provides practical insights for practitioners regarding the implementation of LH in public hospitals in developing countries.

We derive a quantum speed limit for unitary evolution for the case of mixed quantum states using the stronger uncertainty relation for mixed quantum states. This bound can be optimized over different choices of Hermitian operators for a better bound. We illustrate this with some examples and show its better performance with respect to three existing bounds for mixed quantum states.

SStatistical characteristics of the wind speed in Samaria region of Israel have been analyzed by processing 11 years of wind data provided by the Israeli Meteorological Service, recorded at 10 m height above the ground. The cumulative mean wind speed at measurement height was shown to be 4.53 m/s with standard deviation of 2.32 m/s. Prevailing wind direction is shown to be char-acterized by cumulative mean azimuth of 226° with standard deviation of 79.76°. The results were extrapolated to 70-meter height in order to estimate wind characteristics at hub height of a me-dium-scale wind turbine. Moreover, Weibull distribution parameters were calculated annually, monthly and seasonally, demonstrating a good match with histogram-based statistical repre-sentations. Shape parameter of the Weibull distribution was shown to reside within a narrow range of 1.93 to 2.15, allowing us to assume a Rayleigh distribution, thus simplifying wind tur-bines energy yield calculations. The novelty of the current paper is related to gathering wind statistics for a certain area (Samaria) we are not aware of any published statistics regarding wind velocity and direction in this area. The data may be interesting for potential regional wind energy development in which the obtained Weibull distribution can be used in calculations of expected power generation of particular turbines with known power dependence on velocity. We also point out that the fact that realistic wind velocity statistics is well described by an analytic formula (Weibull distribution) is not trivial, and in fact the fit may have been poor.

The paper presents models of path and control planning for parking, docking, and movement of autonomous vehicles at low speeds considering space constraints. Given the low speed of motion, and in order to test and approve the proposed algorithms, vehicle kinematic models are used. Recent works on the development of parking algorithms for autonomous vehicles are reviewed. Bicycle kinematic models for vehicle motion are considered for three basic types of vehicles: passenger car, long wheelbase truck, and articulated vehicles with and without steered semitrailer axes. Mathematical descriptions of systems of differential equations in matrix form and expressions for determining the linearization elements of nonlinear motion equations that increase the speed of finding the optimal solution are presented. Options are proposed for describing the interaction of vehicle overall dimensions with the space boundaries, within which a maneuver should be performed. An original algorithm that considers numerous constraints is developed for determining vehicle permissible positions within the closed boundaries of the parking area, which are directly used in the iterative process of searching for the optimal plan solution using nonlinear model predictive control (NMPC). The process of using NMPC to find the best trajectories and control laws while moving in a semi-limited space of constant curvature (turnabouts, roundabouts) are described. Simulation tests were used to validate the proposed models for both constrained and unconstrained conditions and the output (state-space) and control parameters' dependencies are shown. The proposed models represent an initial effort to model the movement of autonomous vehicles for parking and has the potential for other highway applications.

The classification of Trojans in modern analog microcircuits is considered. Using high-speed operational amplifiers (Op-Amps) as an example, the relationship between Op-Amp circuit design and the formation of undesirable states in typical switching circuits is shown. Circuit solutions are proposed to minimize the Trojan states of high-speed Op-Amps. These include limiting the maximum output currents of the input stages of the Op-Amp during the transient process and the use of differentiating transient correction circuits in the Op-Amp.

In this paper, solar irradiance and wind speed forecasts were performed considering time horizons ranging from 10 min to 60 min, under a 10 min time-step. Global horizontal irradiance (GHI) and wind speed were computed using four forecasting models (Random Forest, k-Nearest Neighbours, Support Vector Regression, and Elastic Net) to compare their performance against two alternative dynamic ensemble methods (windowing and arbitrating). Forecasting models and dynamic forecasting ensembles were implemented in Python for performance evaluation. The performance comparison between the prediction models and the dynamic ensemble methods was carried out by evaluating the RMSE, MAE, R² and MAPE, to evaluate whether the dynamic ensemble forecasting method obtained greater. According to the results obtained windowing dynamic ensemble method was the most efficient among the tested. For the wind speed data, by varying its parameter λ (from 1 to 100), a variable performance profile was obtained, where from λ =1 to λ = 74, windowing proved to be the most efficient, reaching maximum efficiency for λ = 19. Windowing was the best method for the GHI analysis, reaching its best performance for λ = 1. The efficiency gain using windowing was 0.56% when using the wind speed model and 1.96% for GHI.

The common dandelion uses a bundle of drag-enhancing bristles (the pappus) that enables seed dispersal over formidable distances; however, the scaling laws of aerodynamic drag underpinning pappus-mediated flight remains unresolved. In this paper, we study the aerodynamic shape of dandelion, derive the scaling law of resistance, determine the Vogel exponent. In particular, we find that the total drag coefficient is proportional to the -2/3 power of the dandelion pappus Reynolds number, and obtain the terminal velocity of the dandelion seed under gravitation field.

Information is commonly considered as a mathematical quantity that forms the basis of computing. In mathematics, information can propagate instantly, so its transfer speed is not the subject of information science. In all kinds of implementations of computing, whether technological or biological, some material carrier for the information exists, so the information’s propagation speed cannot exceed the speed of the carrier. Because of this limitation, for any implementation, one must consider the transfer time between computing units. We need a different mathematical method to take this limitation into account: classic mathematics can only describe infinitely fast and infinitely small computing system implementations. The difference between the mathematical handling methods leads to different descriptions of the behavior of the systems. The correct handling also explains why biological implementations can have lifelong learning and technological ones cannot. The conclusion about learning evidences matches others’ experimental evidence, both in technological and biological computing.

In this paper, we investigate how Rindler observer measures the universe in the ADM formalism. We compute his measurements in each slice of the space-time in terms of gravitational red-shift which is a property of general covariance. In this way, we found special relativity preferred frames to match with the general relativity Rindler frame in ADM formalism. This may resolve the widely known incompatibility between special relativity and general relativity on how each theory sees the red-shift. We found a geometric interpretation of the speed of light and mass.

The scheme to realize high speed (~250Gb/s) all-optical Boolean logic gates using semiconductor optica amplifiers with quantum-dot (QD-SOA) is introduced and analyzed in this review. Numerical simulation method was presented by solving the rate equation and taking into account nonlinear dynamics including carrier heating and spectral hole-burning. Binary phase shift keyed (BPSK) signal and on-off keyed signal are used to generate high speed all-optical logic gates. The applications based on all-optical logic gates such as, all-optical latches, pseudo random bit sequence (PRBS) generation and all-optical encryption, are also discussed in this review. Results show that the scheme based on QD-SOA is a promising method for the realization of high speed all-optical communication system in the future.

Our analysis of previous studies shows that solar energy and wind can consume negligible amount of water to generate one megawatt of electricity.

Although data acquisition is a very usual technique, there are several aspects not always considered, as synchronization of acquired measures and evaluation of the errors that derive from this fact. The paper hereby aims to point this thing out, by mathematical determination of the necessary correction and implementing the software meant to evaluate the performances of the acquisition system. As an example, a three-phased acquisition system has been developed in order to monitor the currents and voltages on the three phases. Also other measures have been calculated, such as power and phase. The components on each phase don’t have to be fully identified because a whole system calibration can be made in the first stage. Calibration consists in finding the weighting coefficients for each quantity. The implemented solution for three-phased measures data acquisition starts from the hypothesis of a sampling frequency that respects Shannon theorem. The distance between two samples is small enough to consider a linear evolution between two moments for the same measure. Errors that affect the above mentioned, due to the different moments of time when samples are acquired, are analyzed and brought to the minimum value.

Despite good intentions, the increasing number of plastic bag bans aimed at alleviating marine plastic pollution saw a correlated increase in the number of unintended consequences that emerged alongside the bans, suggesting that human behavior towards plastic bag consumption have not changed, but merely shifted, and are feeding into other major international environmental catastrophes. Nudge theory, which helps people make better choices for themselves without inhibiting their free will, is a potential solution that has been shown to play a subtle but important role in providing options under circumstances where complex information needs to be streamlined for the wider community, avoiding any unintended consequences and behavioural shifts that might arise from instruments that diminishes autonomy. It is therefore timely to look into the insights of nudge theory to encourage a positive behavioural change to reduce plastic bag consumption. Here we apply a systematic literature review to show how successful applications of nudges in supermarkets can be leveraged to reduce plastic bag consumption. We find that the current applications of nudges in various industries worldwide, including supermarkets have produced positive and encouraging results, as well as producing lasting behavioural change among the wider community. Supermarkets are identified as a powerful deployment site of these nudges due to their positioning as a dominant provider of plastic bags to the wider community, as well as being the largest and leading provider of daily food needs. Finally, we synthesise our findings to produce a coherent and testable framework of actionable interventions that supermarkets can employ to nudge customers towards reduced plastic bag reliance, accompanied with a visual timeline of a customer shopping in a supermarket experiencing these nudges.

Excessive cell phone use contributes to distracted driving, may increase risk for automobile accidents, and a minority of mobile phone users exhibit behaviors consistent with technological addiction. The purpose of this study was to determine whether cell phone beliefs and behaviors could be changed by a brief educational encounter. The Theory of Reasoned Action provided a lens for viewing attitudes and behavior. A one-week pre-post design with a thirty-day follow-up was used with participants (N = 215, 67.0% female, age = 20.0 + 1.6) assigned to a peer led intervention or comparison groups. The intervention included cell-phone educational materials. A short index of cell phone behavior was developed which showed good internal consistency with a Cronbach’s alpha of .81. The intervention group “agreed” or “strongly-agreed” more than the comparison group on five of the seven areas of cell phone beliefs and behaviors ( p < 0.05, item Cohen’s d = .32 to .47, total d = .50) at one-week following receipt of informational materials. We conclude that attitudes and behaviors regarding cell phones are malleable and susceptible to change in young-adults following a brief psychoeducational intervention.

Healthy houses is a problem on developing countries. This study mainly focus on urban areas and the health effect of poor water and sanitation, floor, inadequate heating, poor food storage and overcrowding. This research has used qualitative method with questionnaires has spread to a hundred and six homes about characteristics of healthy home. The questionnaires have spread to Pondok village and Bukit Kerman village, Kerinci District, Jambi Province, Indonesia. Result showed 90% houses too dense and 10 no dense, 98% houses on this area are unhealthy houses and 10% healthy houses. Unhealthy houses that affected diseases such as 20% diaarhea, 29% other diseases, 13% ARI, 10% malaria 15% skin and 12% no diseases. We recommended to make a public health policy to reducing unhealthy houses on this area.

Stray currents can cause very rapid degradation and material loss at the points where the current leaves the metal and enters the electrolyte. Nowadays, many resources are invested in the protection of jeopardized structures, such as buried pipelines, from stray current corrosion. This paper describes the measures that need to be considered in the design and construction of track structures to ensure high rail-to-ground resistance and consequently reduce stray currents. The main conclusions from existing guidelines and standards for reducing and controlling stray currents that are applied by various track operators are presented in the paper. Rail-to-ground resistance in different types of tracks structures and rail fastening systems is analysed and optimal type of the track and type of the fastening system is defined. The grounding schemes used on the tracks and their influence on stray current values are described, as well as the influence of traction power substation and rail cross bonding on stray current. Since it is not necessary to apply all the measures described to the same track structure, the paper gives recommendations on which measures to apply when building tracks with continuously fastened rails and which to apply when building tracks with discretely supported and fastened rails.

It has been known for a long time that many people who stutter are immediately fluent in certain conditions, for instance, when they speak in unison with others, in sync with the clicking of a metronome, or when they hear themselves speak in an altered manner. To understand why stuttering is reduced or even eliminated in such conditions is desirable because it may help understand why stuttering occurs in normal speaking conditions. However, empirical findings in this area appear conflicting and confusing, especially with regard to the role of auditory feedback. The article gives an overview of the variety and diversity of fluency-enhancing conditions and of theories proposed to explain their effect. These theories are evaluated in the light of recent empirical findings. A new hypothesis is proposed, based on findings showing that speech processing is limited without attention to the auditory channel. It is assumed that fluency-enhancing conditions draw the speaker’s attention to the auditory channel and, thereby, improve the processing of auditory feedback and its use in speech control. Implications of this account for a causal theory of stuttering and for the treatment of the disorder are discussed.

Citron watermelon (Citrullus lanatus var. citroides) is an underexploited and under-researched crop species with potential to contribute to crop diversification in sub-Saharan Africa and beyond. The species is commonly cultivated in the drier parts of Southern Africa, mainly by smallholder farmers who maintain a wide range of landraces. Understanding the molecular and morpho-physiological basis for drought adaptation of Citron watermelon in these dry environments can aid in screening local germplasm, identification of suitable traits for crop improvement and improving food system resilience among smallholder farmers by adding to crop diversification. This paper reviews literature on drought adaptation of C. lanatus spp. (C3 xerophytes), using the systematic review approach. The review discusses; (i) the potential role of citron watermelon in adding to crop diversification, (ii) alternative food uses and potential by-products that can be processed from citron watermelon and (iii) the role of Sub-Saharan farmers as key actors in conserving citron watermelon germplasm and biodiversity. Finally, the review provides a summary of significant findings and identifies critical knowledge gaps for further research.

In modern Commercial Off-The-Shelf (COTS) multicore systems, cores can produce several simultaneous memory requests. The processing of such requests over the memory controller negatively impacts the interference delay triggered by running parallel tasks on the platform. In this paper, we propose a software-based testing approach for analyzing memory interference delay, when cores are exposed to extensive read/write requests that access in parallel their Cache Coherent Interconnect. The hardware targeted in this work is the well-known LayerScape QorIQ LS2085A, which can be approached as a potential successor to the Freescale QorIQ P4080. The test analysis was conducted based on a bare-metal operating system that we developed to guarantee a deterministic execution environment at all time points. Our testing was accomplished using a set of carefully designed synthetic benchmarks as well as TACLeBench benchmarks.

Terpenoids are toxic compounds produced by plants as a defense strategy against insect herbivores. We tested the effect of Origanum vulgare terpenoids on the generalist herbivore Spodoptera littoralis and the response of the plant to herbivory. Terpenoids were analyzed by GC-FID and GC-MS and quantitative gene expression (qPCR) was evaluated on selected plant genes involved in both terpene biosynthesis. The insect detoxification response to terpenes was evaluated by monitoring antioxidant enzymes activity and expression of insect genes involved in terpene detoxification. O. vulgare terpenoid biosynthesis and gene expression was modulated by S. littoralis feeding. The herbivore-induced increased level of terpenoids (particularly carvacrol and p-cymene) interacted with the herbivore by decreasing larval survival and growth rate. The assimilation by S. littoralis of more than 50% of ingested terpenes correlated with the possible toxic effects of O. vulgare terpenoids. In choice test experiments, carvacrol and γ-terpinene mediated the larval feeding preferences, wherease the prolonged feeding on O. vulgare terpenoids (particularly on γ-terpinene) exerted relevant antinutritional effects on larvae. S. littoralis was found to react to O. vulgare terpenoids by increasing its antioxidant enzymes activities and gene expression, although this was not sufficient to sustain the toxicity of O. vulgare terpenoids.

In this work, we propose an easy and a low cost method for the synthesis of Nitrogen-Doped Graphene NDG and its silver nanowires NW functionalization NWGN. The synthesis was performed using the improved graphene oxide method, chemical reduction of graphene oxide in the presence of caffeine as green nitrogen source and the subsequently the silver nanowires growth in the surface, by the chemical reductions salts in the presence of NG. Achieving a homogeneous growing (coating) of graphene sheets. The samples were analyzed using conventional characterization techniques: SEM-EDX, XRD, FT-IR, RAMAN, TEM, HRTEM, STEM and XPS.

Dietary recommendations to decrease the risk of cardiovascular disease (CVD) have focused on reducing intake of saturated fatty acids (SFA) for more than 50 years. While the 2015-2020 Dietary Guidelines for Americans advise substituting both monounsaturated and polyunsaturated fatty acids for SFA, evidence supports other nutrient substitutions that will also reduce CVD risk. For example, replacing SFA with whole grains, but not refined carbohydrates, reduces CVD risk. Replacing SFA with protein, especially plant protein may also reduce CVD risk. While dairy fat (milk, cheese) is associated with a slightly lower CVD risk compared to meat, dairy fat results in a significantly greater CVD risk relative to unsaturated fatty acids. As research continues, we will refine our understanding of dietary patterns associated with lower CVD risk.

This paper develops a two-layer optimization approach that provides energy-optimal control for vehicles and traffic signal controllers. The optimizer in the first layer computes the traffic signal timings to minimize the total energy consumption levels of approaching vehicles from upstream traffic. The traffic signal optimization can be easily implemented in real-time signal controllers, and it overcomes the issues in the traditional Webster’s method of overestimating the cycle length when the traffic volume-to-capacity ratio exceeds 50 percent. The second layer optimizer is the vehicle speed controller, which calculates the optimal vehicle brake and throttle levels to minimize the energy consumption of individual vehicles. The A-star dynamic programming is used to solve the formulated optimization problem in the second layer to expedite the computation speed so that the optimal vehicle trajectories can be computed in real-time and can be easily implemented in simulation software for testing. The proposed integrated controller is first tested on an isolated signalized intersection, and then an arterial network with multiple intersections to investigate the performance of the proposed controller under various traffic demand levels. The test results demonstrate that the proposed integrated controller can greatly improve energy efficiency with fuel savings up to 17.7%, at the same time enhancing traffic mobility by up to 47.18% reduction in traffic delay and up to 24.84% reduction in vehicle stops.

The purpose of the present study was to examine the relationships between bat swing speed (BSS) and muscle thickness and lateral asymmetry of the trunk and limbs in collegiate baseball players. Twenty-four collegiate baseball players participated in this study. The maximum BSS in hitting a teed ball was measured using a motion capture system. The muscle thicknesses of the trunk (upper abdominal rectus, central abdominal rectus, lower abdominal rectus, abdominal wall, and multifidus lumborum), upper limb, and lower limb were measured using a B-mode ultrasonography. Lateral asymmetry between each pair of muscles was determined as the ratio of the thickness of the dominant side to that of the non-dominant side. Significant positive correlations were observed between BSS and muscle thicknesses of the abdominal wall and multifidus lumborum on the dominant side (r = 0.426 and 0.431, respectively; p < 0.05), while nearly significant positive correlations were observed between BSS and muscle thicknesses on the non-dominant side. No significant correlations were found between BSS and lateral asymmetry of all muscles. These findings indicate the importance of the trunk muscles for bat swing, and the lack of association between BSS and lateral asymmetry of muscle size.

The continuously developing project aims to build an informatics system enabling analysis of spatial and temporal parameters of movement activities occurring in the sport of speed climbing. The monitoring system (climbing information speed system – CISS) is to be used for conducting comprehensive scientific research in the field of speed climbing. The system enables the evaluation of the training process of climbers at various levels of competition. The study analysis was based on video. The video recording with a camera positioned at a short distance (10 m) from the wall. The marker was positioned closest to the centre of mass (gravity) BMC. Results: development of a system for data collection and analysis of the climbing run based on video recording (application of the Kanade-Lucas-Tomasi (KLT) algorithm). Our results showed that used devices can measure a wide range of specific internal and external variables during speed climbing. Some of the analyzed parameters were significantly correlated with speed climbing time. These results could be a theoretical basis for future research and for training program’s preparation.

Improving the operational reliability of nuclear power plants, combined heat and power plants (CHP), as well as oil and gas pipelines is a priority task in the development of a variable-speed drive for lock valves used at these facilities. The paper analyzes technical requirements for such devices; the motor has been selected, its electrical equilibrium and moment equations have been obtained; recommendations for the selection of the kinematic drive scheme have been formulated. Based on the theoretical data obtained, a prototype has been developed, manufactured and tested.

Unification point of view, quantum cosmology must be given a priority and one should make a note that, Spin is a basic property of quantum physics and rotation is a very common experience. In this context, we have developed a quantum model of cosmology associated with Machian universe having Planck scale origin, total dark matter, light speed rotation and equality of gravitational self energy density and thermal energy density. We would like to appeal that, observed cosmic radius and age seem to be shortened by 146.3 times their actual magnitudes.

Spaceborne altimeters are an important data source for obtaining global sea surface wind speeds (U10). Although many altimeter U10 algorithms have been proposed and they perform well, there is still room for improvement. In this study, the data from ten altimeters were collocated with buoys to investigate the error of the altimeter U10 retrievals. The U10 residuals were found to be significantly dependent on many oceanic and atmospheric parameters. Because these oceanic and atmospheric parameters are inter-correlated, an asymptotic strategy was used to isolate the impact of different parameters and establish a neural-network-based correction model of altimeter U10. The results indicated that significant wave heights and mean wave periods are effective in correcting U10 retrievals, probably due to the tilting modulation of long-waves on the sea surface. After the wave correction, the root-mean-square error of the retrieved U10 was reduced from 1.42 m/s to 1.24 m/s and the impacts of thermodynamic parameters, such as sea surface (air) temperate, became negligible. The U10 residuals after correction showed that the atmospheric instability can lead to errors on extrapolated buoy U10. The buoy measurements with large air-sea temperature differences need to be excluded in the Cal/Val of remotely sensed U10.

The predictability of wind information in a given location is essential for the evaluation of a wind power project. Predicting wind speed accurately improves the planning of wind power generation, reducing costs and improving the use of resources. This paper seeks to predict the mean hourly wind speed in anemometric towers (at a height of 50 meters) at two locations: a coastal region and one with complex terrain characteristics. To this end, the Holt-Winters (HW), Artificial Neural Networks (ANN) and Hybrid time-series models were used. Observational data evaluated by the Modern-Era Retrospective analysis for Research and Applications-Version 2 (MERRA-2) reanalysis at the same height of the towers. The results show that the hybrid model had a better performance in relation to the others, including when compared to the evaluation with MERRA-2. For example, in terms of statistical residuals, RMSE and MAE were 0.91 and 0.62 m/s, respectively. As such, the hybrid models are a good method to forecast wind speed data for wind generation.

Cancer cells show an increased glutamine consumption. The glutaminase (GLS) enzyme controls a limiting step in the glutamine catabolism. Breast tumors, especially the triple negative subtype, have a high expression of GLS. Our recent study demonstrated that GLS activity and ammonia production are inhibited by Sirtuin 5 (SIRT5). We have developed MC3138, a selective SIRT5 activator. Treatment with MC3138 mimicked the deacetylation effect mediated by SIRT5 overexpression. Moreover, GLS activity is regulated by inorganic phosphate (Pi). Considering the interconnected role of GLS, SIRT5 and Pi for cancer growth, our hypothesis is that activation of SIRT5 and reduction of Pi could represent a valid anti-tumoral strategy. Treating cells with MC3138 and lanthanum acetate, a Pi chelator, decreased cell viability and clonogenicity. We also observed a modulation of LC3 and ULK1 with MC3138 and lanthanum acetate. Interestingly, inhibition of mitophagy marker BNIP3 was observed only in the presence of MC3138. Such autophagy and mitophagy modulation was accompanied by an increase of cytosolic and mitochondrial reactive oxygen species (ROS). In conclusion, our results show how SIRT5 activation and/or Pi binding can represent a valid strategy to inhibit cell proliferation by reducing glutamine metabolism and mitophagy leading to a deleterious accumulation of ROS.

The world is in the grips of the COVID-19 pandemic. Public health measures that can reduce the risk of infection and death in addition to quarantines are desperately needed. This article reviews the roles of vitamin D in reducing risk of respiratory tract infections, knowledge about the epidemiology of influenza and COVID-19, and how vitamin D supplementation might be a useful measure to reduce risk. Through several mechanisms, vitamin D can reduce risk of infections. Those mechanisms include inducing cathelicidins and defensins that can lower viral replication rates and reducing concentrations of pro-inflammatory cytokines that produce the inflammation that injures the lining of the lungs, leading to pneumonia, as well as increase concentrations of anti-inflammatory cytokines. Several observational studies and clinical trials reported that vitamin D supplementation reduced risk of influenza, whereas others did not. Evidence supporting the role of vitamin D in reducing risk of COVID-19 includes that the outbreak occurred in winter, a time when 25-hydroxyvitamin D [25(OH)D] concentrations are lowest; that the number of cases in the Southern Hemisphere near the end of summer are low; that vitamin D deficiency has been found to contribute to acute respiratory distress syndrome, and that case-fatality rates increase with age and with chronic disease comorbidity, both of which are associated with lower 25(OH)D concentration. To reduce risk of infection, it is recommended that people at risk of influenza and/or COVID-19 consider taking 10,000 IU/d of vitamin D₃ for a few weeks to rapidly raise 25(OH)D concentrations, followed by 5000 IU/d. The goal should be to raise 25(OH)D concentrations above 40–60 ng/ml (100–150 nmol/l). For treatment of people who become infected with COVID-19, higher vitamin D₃ doses might be useful. Randomized controlled trials and large population studies should be conducted to evaluate these recommendations.

Unmanned aerial vehicle (UAV), or drone is recognized for its potential to improve efficiency and address last-mile delivery issues. As a result, there has been a lot of activity in recent years in the field of drone scheduling and routing. Unlike the vehicle routing problem, drone route design is difficult due to several operational characteristics, such as speed optimization, multitrip operation, and energy consumption estimation. On the one hand, drone energy consumption is a complex nonlinear function of both speed and payload in practice. On the other hand, the high operating speed of drones can significantly curtail the drone range, thereby limiting the efficiency of drone delivery systems. Most of the existing drone delivery models either assume constant drone speed or do not consider the effect of drone speed and parcel weight on energy consumption, leading to costly or energy-infeasible routes. This paper addresses the trade-off between speed and flight range in a multi-trip drone routing problem with variable flight speeds (DRP-VFS), in which a team of homogeneous drones is employed for delivery services. We propose a new model to particularly consider energy constraints using a nonlinear energy consumption model and treat drone speeds as decision variables so that various drone speeds can be adopted in applications. The DRP-VFS is initially formulated as mixed-integer linear programming (MILP) to minimize total energy consumption. To solve large-scale instances, we propose a three-phase adaptive large neighborhood search (ALNS) algorithm. The experimental results demonstrate that suboptimal solutions can be found effectively in practical scenarios using the proposed method. Furthermore, results indicate that operating drones at variable speeds leads to about 21% of energy savings compared to fixed speeds, boasting advantages in cost-savings and range extensions.

A variable speed anti-tangling reel mechanism was designed to address the problems of tangling, hanging and rewinding of the tassel wheel and the high paddling loss in the current Chinese rape combine harvester cutting table. The kinematic equations of the reel mechanism were developed, and the analysis showed that the speed in the entry stage is low and the speed in the exit stage is high, and the attitude of the reel teeth change with the rape plant movement during the whole paddling process. A single-factor test and a multi-factor regression orthogonal combination test were carried out using the cutting table loss rate of rape harvesting as the evaluation index. The main and secondary factors affecting the cutting table loss of the variable speed reel were obtained as the reel speed, the machine travel speed and the ground angle of the frame. A mathematical model of regression of cutter loss and the main influencing factors was established, with the coefficient of determination R2 = 0.9918. The optimal combination of parameters for the variable speed reel was obtained with the lowest cutting table loss rate in rape harvesting as the optimization target: reel speed 25r/min, frame parallel to the ground and implement travel speed 0.7m/s. Field validation tests and comparative tests of cutting table loss of the two reels were carried out. The test results show that the regression mathematical model of the cutting table loss is more accurate, and the cutting table loss is reduced by 13.9% with the variable speed reel compared to the cam-action reel, and there are no problems with the paddle teeth hanging and tangling during the paddling process.

This paper develops a Green Light Optimal Speed Advisory (GLOSA) system for buses (B-GLOSA). The proposed B-GLOSA system is implemented on diesel buses, and field tested to validate and quantify the potential real-world benefits. The developed system includes a simple and easy to calibrate fuel consumption model that computes instantaneous diesel bus fuel consumption rates. The bus fuel consumption model, a vehicle dynamics model, the traffic signal timings, and the re-lationship between vehicle speed and distance to the intersection are used to construct an optimi-zation problem. A moving-horizon dynamic programming problem solved using the A-star algo-rithm is used to compute the energy-optimized vehicle trajectory through signalized intersections. The Virginia Smart Road test facility was used to conduct the field test on 30 participants. Each participant drove three scenarios including a base case uninformed drive, an informed drive with signal timing information communicated to the driver, and an informed drive with the recom-mended speed computed by the B-GLOSA system. The field test investigated the performance of using the developed B-GLOSA system considering different impact factors, including road grades and red indication offsets, using a split-split-plot experimental design. The test results demonstrated that the proposed B-GLOSA system can produce smoother bus trajectories through signalized in-tersections producing fuel consumption and travel time savings. Specifically, compared to the uninformed drive, the B-GLOSA system produces fuel and travel time savings of 22.1% and 6.1% on average, respectively.

This paper presents a methodology to calculate day-ahead wind speed predictions based on historical measurements done by weather stations. The methodology was tested for three locations: Colombia, Ecuador, and Spain. The data is input into the process in two ways: 1) as a single time series containing all measurements, and 2) as twenty-four separate parallel sequences, corresponding to the values of wind speed at each of the 24 hours in the day over several months. The methodology relies on the use of three non-parametric techniques: Least-Squares Support Vector Machines, Empirical Mode Decomposition, and the Wavelet Transform. Also, the traditional and simple Auto-Regressive model is applied. The combination of the aforementioned techniques results in nine methods for performing wind prediction. Experiments using a MATLAB implementation showed that the Least-squares Support Vector Machine using data as a single time series outperformed the other combinations, obtaining the least mean square error.

It is important to reduce the computation complexity while maintaining the accuracy of convolution neural networks. We deem it is possible to further reduce the network complexity while ensuring the accuracy. In this paper, we propose a novel feature extraction network called DSRNet which is lightweight but effective. DSRNet follows the basic ideas of stacking modules and short connection, introduces Depthwise Separable convolution and utilizes the Dilated convolution. The proposed network has fewer parameters and achieves outstanding speed. We conducted comprehensive experiments on CIFAR10, CIFAR100 and STL10 datasets, and the results showed the DSRNet has great performance improvement in terms of accuracy and speed.

Researchers have been exploring seaweed to reduce methane (CH4) emissions from livestock. This study aimed to investigate the potential of a red alga, Bonnemaisonia hamifera, as an alternative to mitigate CH4 emissions. B. hamifera, harvested from the West coast of Sweden, was used in an in vitro experiment using a fully automated gas production system. The experiment was a ran-domized complete block design consisting of a 48-h incubation that included a control (grass si-lage) and B. hamifera inclusions at 2.5%, 5.0% and 7.5% of grass silage OM mixed with buffered rumen fluid. Predicted in vivo CH4 production and total gas production were estimated by ap-plying a set of models to the gas production data and in vitro fermentation characteristics were evaluated. The results demonstrated that the inclusion of B. hamifera reduced (P = 0.01) predicted in vivo CH4 and total gas production, and total gas production linearly decreased (P = 0.03) with higher inclusion of B. hamifera. The molar proportion of propionate increased (P = 0.03) while isovalerate decreased (P = 0.04) with inclusion of B. hamifera. There was a tendency for increased (0.06 ≤ P ≤ 0.10) total volatile fatty acid production, as well as lower proportions of butyrate, isobutyrate, and 2-methylbutyrate. Chemical analyses revealed that B. hamifera had moderate concentrations of polyphenols. The iodine content was low and there was no detectable bromo-form, suggesting quality advantages over Asparagopsis taxiformis. Additionally, B. hamifera exhib-ited antioxidant activity comparable to the positive control Resveratrol. The findings of this study indicated that B. hamifera harvested from temperate waters in Sweden possesses capacity to mitigate CH4 in vitro.

Neuroprotective strategies for stroke remain inadequate. Nanoliposomes comprised of phos-phatidylcholine, cholesterol and monosialogangliosides (NL) induced an antioxidant protective response in endothelial cells exposed to amyloid insults. We tested the hypotheses that NL will preserve SH-SY5Y neuroblastoma cell viability following hypoxic injury and will reduce injury in mice following middle cerebral artery occlusion (MCAO). Neuroblastoma were exposed to 20-hour physoxic (5% oxygen) or hypoxic (1% oxygen) condition without or with NL (100 or 300 µg/mL). Viability was measured using calcein-AM fluorescence and SH-SY5Y gene expression of antioxidant proteins heme oxygenase-1 (HO-1), NAD(P)H quinone dehydrogenase 1 (NQO1) and superoxide dismutase 1 (SOD1) were measured by quantitative polymerase chain reaction. C57BL/6J mice were treated with saline (N=8) or NL (10000 ug/mL, N=7) while undergoing 60-minute MCAO followed by reperfusion. Day 2 post-injury neurologic impairment score and infarction size were compared. Neuroblastoma showed reduced viability following hypoxia that was reversed by NL. NL increased gene expression of HO-1, NQO1 and SOD1 versus controls. NL-treated mice showed reduced neurologic impairment and brain infarct size (18.8±2% versus 27.3±2.3%, p=0.017) versus controls. NL reduced stroke injury in mice subjected to MCAO likely through induction of an antioxidant stress response. NL is a candidate novel agent for stroke.

The current emerging COVID-19 pandemic has caused a global impact on every major aspect of our societies. It is known that SARS-Cov-2 can endure harsh environmental conditions for up to 72 h, which may contribute to its rapid spread. Therefore, effective containment strategies, such as sanitizing, are critical. Nanotechnology can represent an alternative to reduce the COVID-19 spread, particularly in critical areas, such as healthcare facilities and public places. Nanotechnology-based products are effective at inhibiting different pathogens, including viruses, regardless of their drug-resistant profile, biological structure, or physiology. Although there are several approved nanotechnology-based antiviral products, this work aims to highlight the use of nanomaterials as sanitizers for the prevention of the spread of mainly SARS-Cov-2. It has been widely demonstrated that nanomaterials are an alternative for sanitizing surfaces to inactivate the virus. Also, antimicrobial nanomaterials can reduce the risk of secondary microbial infections on COVID-19 patients, as they inhibit the bacteria and fungi that can contaminate healthcare-related facilities. Finally, cost-effective, easy-to-synthesize antiviral nanomaterials could reduce the burden of the COVID-19 on challenging environments and in developing countries.

Introduction: The treatment of peritoneal dialysis in end-stage renal disease is increasing in clinical practice. The main purpose of this study was to evaluate the effect of far-infrared radiation therapy on inflammation and the cellular immunity of patients undergoing peritoneal dialysis. Materials and Methods: We recruited 56 patients undergoing peritoneal dialysis, and we included 32 patients from the experimental group and 24 patients from the control group in the final analysis. The experimental evaluation in our study was as follows: (1) We used abdominal computed tomography to measure the diameter and degree of hardening of the abdominal veins and large blood vessels to explore the changes in abdominal blood vessels. (2) The study compared the effects of peritoneal dialysis using albumin, blood urea nitrogen, creatinine, white blood cell, neutrophil-to-lymphocyte ratio, platelet-to-lymphocyte ratio, erythrocyte sedimentation rate, Hs-CRP clearance rate, and HBAlC. (3) We compared the cytokine concentration of blood between the two groups while controlling for GM-CSF, IL-2, IFN-γ, IL-6, IL-18, IL-4, IL-5, IL-13, IL-12p70, TNF-α, and IL-1β. Results and Discussion: (1) There was no significant difference in the abdominal blood vessels of the experimental group relative to the control group according to abdominal CT measured over 6 months. (2) Our study demonstrates the statistically significant effect of FIR therapy on the following parameters: albumin (p = 0.048*), creatinine (p = 0.039*), and Hs-CRP (p < 0.001**) decreased significantly, and glomerular filtration rate (eGFR, p = 0.043*) and glucose (p < 0.001**) increased significantly. Our study found that, in the experimental group, albumin and creatinine decreased significantly due to FIR therapy for 6 months. However, our study also found that, in the experimental group, glucose (p < 0.001**) increased significantly due to FIR therapy for 6 months. Peritoneal dialysis combined with FIR can reduce the side effects of glucose in dialysis buffer, which interferes with peritoneal inflammation and peritoneal mesothelial cell fibrosis. In addition, we also found that, in the experimental group, Hs-CRP (p < 0.001**) decreased significantly due to FIR therapy for 6 months. (3) No statistical significance in the inflammatory cytokines related to FIR therapy differences was observed in our study. IFN-γ (p = 0.124), IL-12p70 (p = 0.093), IL-18 (p = 0.213), and TNF-α (p = 0.254) did not exhibit significant improvements in peritoneal dialysis with FIR treatment over 6 months. IFN-γ and IL-18 in the plasma of patients in the experimental group and the control group were higher in the third month than in the first month. Conclusion: We found that the effect of peritoneal dialysis improved significantly with FIR therapy, and significant improvements in the peritoneal permeability and inflammatory response were observed. end-stage renal disease; peritoneal dialysis; far-infrared therapy (FIR)

The improvement of energy efficiency of hydraulic systems remains to be an essential challenge for the industry, and the demand for more sustainable solutions is increasing. A main focus in this endeavor is the ability to eliminate or strongly reduce the use of throttle control valves which have been the preferred control element in industrial hydraulic systems for decades. Components have been subject to continuous evolution, and current industrial grade hydraulic pumps and motors are both efficient and reliable. Even though few percentages of energy efficiency can still be achieved, the main achievements in terms of efficiency is associated with novel system designs rather than further development of components. An area subject to increasing attention is the field of variable-speed displacement control, allowing to avoid the main control valve throttle losses. Systems using this technology are, however, mainly developed as standalone drive systems, necessitating maximum force, speed and power installed in each axis, with limited hydraulic power distribution capability as compared to valve controlled systems. An emerging field addressing this challenge is so-called electro-hydraulic variable-speed drive networks which allow to completely eliminate the use of control valves and enables power sharing both electrically and hydraulically, potentially reducing the necessary installed power in many cases. The idea of such a technology was first proposed in 2022, and so far developments reported in literature have mainly been of theoretical nature. This article presents the first ever experimental results for a dual cylinder electro-hydraulic variable-speed drive network prototype. The prototype has been developed for an industrial application, but has initially been implemented in a laboratory testbench. Extensive data acquisition has been conducted while subject to the associated industrial motion cycle, under different load conditions. The data is further used in combination with models to predict the total efficiency of the drive network prototype under higher loads than what could be achieved in the laboratory, suggesting a total efficiency from the electric supply to the cylinder pistons of 68 %. Re-configuring the prototype to a known standalone drive system structure implies comparable efficiencies. Finally, the drive network is theoretically compared to a valve drive solution, generally suggesting the prototype drive network to provide efficiency improvements of at least 40 % in comparison.

It has been known that dimensional constants such as ℏ, c, G, e, and k are merely human constructs whose values and units vary depending on the chosen system of measurement. Therefore, the time variation of dimensional constants lacks operational significance due to their dependence on them. It is well-structured and represents a valid discussion. However, this fact only becomes a meaningful debate within the context of a static or present universe. As well-established theoretically and observationally, the current universe is undergoing accelerated expansion, wherein dimensional quantities, like the wavelength of light, also experience redshift phenomena elongating over cosmic time. In other words, in an expanding universe, dimensional quantities of physical parameters vary with cosmic time. From this perspective, there exists the possibility that dimensional constants, such as the speed of light, could vary with the expansion of the universe. In this review paper, we contemplate under what circumstances the speed of light may change or remain constant over cosmic time, and discuss the potential for distinguishing these cases observationally.

Cosmography, as an integral branch of cosmology, strives to characterize the Universe without relying on pre-determined cosmological models. This model-independent approach utilizes Taylor series expansions around the current epoch, providing a direct correlation with cosmological observations and the potential to constrain theoretical models. Various observable quantities in cosmology can be described as different combinations of cosmographic parameters. Furthermore, one can apply cosmography to models with a varying speed of light. In this case, the Hubble parameter can be expressed by the same combination of cosmographic parameters for both the standard model and varying speed of light models. However, for the luminosity distance, the two models are represented by different combinations of cosmographic parameters. Hence, luminosity distance might provide a method to constrain the parameters in varying speed-of-light models.

Advances in technology have introduced remarkable capabilities, particularly in the realm of gathering and accessing vast amounts of data, which has led to the emergence of the "Big Data" era, presenting exciting opportunities to harness the wealth of the generated information. Traffic management centers comprise a stakeholder that can exploit such data towards improving road network operation. This research, explores the utilization of real traffic data, collected by distinct sources on an interurban motorway: static location based aggregate traffic data and probe vehicle data. The first is collected by traffic detectors, while the second involves patrol vehicles’ GNSS data. The traffic quantity analysed is vehicle speed, while specific emphasis has been given on the ap-plication of heatmaps to represent daily traffic patterns and the utilization of k-means clustering. The performed analysis demonstrates the importance of considering spatiotemporal variables as a unified entity when analysing speed in transportation networks. The limitations of using patrol vehicles as estimators of ambient speed, especially in low and heavy traffic conditions, are deline-ated, while the dual purpose of data gathered from these vehicles towards enhancing driving performance and enabling detector maintenance is emphasized. Valuable traffic insights are offered through comprehensive spatiotemporal speed behavior analysis and data combination. The inte-gration of these techniques enhances decision-making for a streamlined and secure transportation system

Wind loads have become one of the key influence factors for the running safety of vehicles and comfort of passengers. Investigation on the wind speed spectrum characteristics of a moving vehicle under turbulent crosswinds is of great influence. Expressions of the wind speed spectrum of a moving vehicle was obtained from the von Kármán spectrum based on Taylor’s frozen flow hypothesis. The influence factors, including the ratio of the vehicle speed to the wind speed and the wind yaw angle from 15° to 175°, were analyzed. The maximum value of the wind speed spectrum and the corresponding frequency were studied as well. The results show that the maximum values of the wind speed spectrum of the moving vehicle were larger than those of the static vehicle. The maximum value of the wind speed spectrum corresponding to the moving vehicle first increased and then decreased as the wind yaw angle increased. Some of the frequencies corresponding to the longitudinal wind speed spectrum values of the moving vehicles were smaller than those of the static vehicle. For moving vehicles, the frequency values corresponding to the maximum values of the longitudinal wind speed spectrum first increased and then decreased as the ratio of the vehicle speed to the wind speed and the wind yaw angle increased.

This paper provides a methodology for the production of synthetic images for training neural networks to recognise shapes and objects. There are many scenarios in which it is difficult, expensive and even dangerous to produce a set of images that is satisfactory for the training of a neural network. The development of 3D modelling software has nowadays reached such a level of realism and ease of use that it seemed natural to explore this innovative path and to give an answer regarding the reliability of this method that bases the training of the neural network on synthetic images. The results obtained in the two proposed use cases, that of the recognition of a pictorial style and that of the recognition of migrants at sea, leads us to support the validity of the approach, provided that the work is conducted in a very scrupulous and rigorous manner, exploiting the full potential of the modelling software. The code produced, which automatically generates the transformations necessary for the data augmentation of each image, and the generation of random environmental conditions in the case of Blender and Unity3D software, is available under the GPL licence on GitHub. The results obtained lead us to affirm that through the good practices presented in the article, we have defined a simple, reliable, economic and safe method to feed the training phase of a neural network dedicated to the recognition of objects and features, to be applied to various contexts.

The ACC feature when activated augments the engine performance in real-time. This article presents a novel methodology to predict the optimal adaptive cruise control set speed profile (ACCSSP) by considering all the effecting parameters. This paper investigates engine operating conditions (EOC) criteria to develop a predictive model of ACCSSP in real-time. We developed a deep learning (DL) model using the NARX method to predict engine operating point (EOP) mapping the vehicle-level vectors (VLV). We used real-world field data obtained from Cadillac test vehicles driven by activating the ACC feature for developing the DL model. We used a realistic set of assumptions to estimate the VLV for the future time steps for the range of allowable speed values and applied them at the input of the developed DL model to generate multiple sets of EOP’s. We imposed the defined EOC criteria on these EOPs, and the top three modes of speeds satisfying all the requirements are derived for each second. Thus three eligible speed values are estimated for each second, and an additional criterion is defined to generate a unique ACCSSP for future time steps. Performance comparison between predicted and constant ACCSSPs indicates that the predictive model outperforms constant ACCSSP.

To monitor the detail information in the sea and on the seafloor, sensors are generally installed on Autonomous Underwater Vehicle (AUV). AUV cannot accurately grasp the absolute position and needs to communicate with the sea-surface vehicle. However, the sea-surface vehicle cannot perform observation operations at high speed and with high efficiency due to low mobility and high human and financial costs. From this perspective, Unmanned Aerial Vehicle (UAV) has possibilities as the next-generation platform. In this study, we conducted a demonstration experiment to use UAV as a sea-surface base for AUV’s underwater communication. We additionally verified the capability of UAV, which can land on and separate from the sea surface, as a drifting buoy to monitor underwater data. Experiment results and obtained data suggest that UAV is suitable for a research operation near the coastal region in terms of position keeping ability, performance against sway, and operation speed as a communication base. To carry out more complicated work (transportation of AUV, etc.) with UAV, new research and development such as weight reduction of AUV will be required.

The principle of the constancy of the velocity of light, which stated that the light velocity is invariant to the motion of the emitter, was well established and directly proven by experiments. Interestingly, the further assumption that the light velocity is independent of the motion of the observer was, arguably, never directly proven by any experiment for a century. This paper proposed the design of two experiments to directly test this assumption, which tried to address some perceived technical difficulty in such experiments. One is to directly measure the light speed as to moving sensors. The experiment setup is designed in such a way that the concerns of time synchronization and dilation can be avoided. Another experiment is to test the isotropy of the light speed to a moving particle in the electromagnetic accelerator by measuring the momentum to acceleration ratio. The experiment result, if positive, will provide direct and solid proof of the assumption. Otherwise, it may imply a need for further investigation. Since the light speed invariance to moving observers is a key assumption of some fundamental physical theory, either way, the experiments will have significant meanings.

By using directed dimensional analysis and data fitting, an explicit universal scaling law for the speed of falling dominoes is formulated. The scaling law shows that domino propagational speed is linear proportional to the 3/2 power of domino separation, and -1/2 power of domino height and thickness.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

The paper deals with the Compound Inverse Rayleigh distribution, shown to constitute a proper model for the characterization of the probability distribution of extreme values of wind-speed, a topic which is gaining growing interest in the field of renewable generation assessment, both in view of wind power production evaluation and the wind-tower mechanical reliability and safety. The first part of the paper illustrates such model starting from its origin as a generalization of the Inverse Rayleigh model - already proven to be a valid model for extreme wind-speeds - by means of a continuous mixture generated by a Gamma distribution on the scale parameter, which gives rise to its name. Moreover, its validity to interpret different field data is illustrated, also by means of numerous numerical examples based upon real wind speed measurements. Then, a novel Bayes approach for the estimation of such extreme wind-speed model is proposed. The method relies upon the assessment of prior information in a practical way, that should be easily available to system engineers. In practice, the method allows to express one’s prior beliefs both in terms of parameters, as customary, and/or in terms of probabilities. The results of a large set of numerical simulations – using typical values of wind-speed parameters - are reported to illustrate the efficiency and the accuracy of the proposed method. The validity of the approach is also verified in terms of its robustness with respect to significant differences compared to the assumed prior information.

The overarching purpose of this review was to highlight the utility of different aerobic field tests in terms of the parameters they provide, with a specific focus on shuttle running and all-out testing. Various field tests are discussed in detail and are categorised according to linear continuous running tests (e.g. 12-minute Cooper Test, University of Montreal Track Test [UMTT], 1200/1600 m time trials, 3-minute all-out test for running [3MT]), intermittent shuttle running tests (e.g. yo-yo inter-mittent recovery test level 1 [YYIR1], 30-15 intermittent fitness test [IFT], and the intermittent all-out shuttle test [IAOST]), and continuous shuttle running tests (e.g. 1.2 km shuttle run test [1.2SRT], maximal multi-stage 20-m shuttle test [MSR], 25-m, 30 m and 50-m 3-minute all-out shuttle test [AOST]). Readers will be guided through the theoretical and practical underpinnings of the 3MT methodology, where the all-out testing methodology is stationed within the testing paradigm, and how to practically implement and interpret the results thereof.

We present a Machian model of Quantum Cosmology with full dark matter and light speed expansion and rotation. During galaxy formation and evolution, fraction of dark matter transforms to visual matter with a relation of the form, m_vis = constant * (m_dark)^2/3. Using this relation and replacing MOND’s ‘critical acceleration’ with “current cosmic maximum angular acceleration”, galactic flat rotation speed range of (50 to 500) km/sec can be fitted well. Estimated flat rotation speeds of DD168, Milky Way and UGC12591 are 49.96 km/sec, 199.66 km/sec and 521.75 km/sec respectively. Based on these striking coincidences, it is possible to say that, MOND’s approach is implicitly connected with cosmological estimation of 95% invisible matter. Considering galactic total matter and current cosmic maximum angular acceleration, galactic working radii, angular velocity and visual matter density can be estimated. Even though, this model is free from ‘big bang’, ‘inflation’, ‘dark energy’, ‘flatness’ and ‘red shift’ issues, at 2.722 K, estimated present Hubble parameter is 66.24 km/sec/Mpc, cosmic radius is 146.3 times the Hubble radius, angular velocity is 146.3 times lower than the Hubble parameter and cosmic age is 146.3 times the Hubble age. With future observations and advanced telescopes, it may be possible to see far distant galaxies and very old stars far beyond the current observable cosmic radius.

The speed with which text can be read is determined in part by the spatial regularity and similarity of vertical letter strokes as assessed by the height of the first peak in the horizontal autocorrelation of the text. The height of this peak was determined for two passages in 20 fonts. The peak was unaffected by the size of the text or its content but was influenced by the font design. Sans serif fonts usually had a lower peak than serif fonts because the presence of serifs resulted in a more even spacing of letter strokes. There were small effects of justification and font- dependent effects of font expansion and compression. The visual comfort of images can be estimated from the extent to which the Fourier amplitude spectrum conforms to 1/f. Students were asked to adjust iBooks to obtain their preferred settings of font and layout. The preference was predicted by the extent to which the Fourier amplitude spectrum approximated 1/f, which in turn was jointly affected by the design of the font, its weight and the ratio of x-height to line separation. The above algorithms can be usefully applied to any orthography to estimate likely speed and comfort of reading.

It is widely believed that the dramatic transformation of the spherical outflows of AGB stars into the extreme aspherical geometries seen during the planetary nebula (PN) phase is linked to binarity and driven by the associated production of fast jets and central disks/torii. The key to understanding the engines that produce these jets and the jet-shaping mechanisms lies in the study of objects in transition between the AGB and PN phases. I discuss the results of our recent studies with high-angular-resolution (with ALMA & HST) and at high-energies (with GALEX, XMM-Newton & Chandra) of several such objects, which reveal new details of close binary interactions and high-speed outflows. These include two PPNe (the Boomerang Nebula and IRAS16342-3814), and the late carbon star, V Hya. The Boomerang is notable for a massive, high-speed outflow that has cooled below the microwave background temperature, making it the coldest object in the Universe. IRAS16342 is the prime example of the class of water-fountain PPNe (very young PPNe with high-velocity H₂O masers) and shows the signature of a precessing jet. V Hya ejects high-speed bullets every 8.5 years associated with the periastron passage of a companion in an eccentric orbit. I discuss our work on AGB stars with strongly-variable high-energy (FUV, X-ray) emission, suggesting that these objects are in the early stages of binary interactions that result in the formation of accretion disks and jets.