The International Renewable Energy Agency (IRENA) was established in 2009 and in 2024, its membership increased to 168 members plus the European Union countries. The purpose of IRENA is to promote the adoption of renewable energy across all industries in the world. Despite the utilization of renewable energy in sectors like power generation and construction, its application in other industries remains limited. Therefore, a literature review study was conducted to investigate the cost and other spatial constraints associated with renewable energy resources, including modeling and optimization techniques that could offer viable solutions to the future challenges faced by the renewable energy production systems. This paper has summarized the result of this study with a focus on the significance of modeling and optimization techniques in energy conservation to highlight the untapped potential for leveraging renewable energy resources in industrial applications. This paper also examined a few case studies from various regions of the world, demonstrating the promising opportunities for research in the modeling and optimization of renewable energy management systems.

The integration of diverse distributed generation (DG) units, encompassing both Renewable Energy Sources (RES) and non-RES technologies delves into voltage levels, current distributions, and power flows, aiming to optimize and effectively manage the distribution network. An RES-based DGs such as photovoltaic systems and wind turbines, alongside non-RES units like fuel cells and micro turbines. This study proposes a hybrid approach the Multi-Objective Genetic Algorithm - Grey Wolf Optimizer (MOGA-GWO). By merging the strengths of multi-objective genetic algorithms with the efficiency of the Grey Wolf Optimizer, this advanced algorithm seeks semi-optimal solutions for multi-objective optimization problems. The algorithm aims to improve convergence speed without compromising solution quality, offering a promising solution for optimizing the characteristics of DG and RES integration in distribution networks compared to Cuckoo Search and Simulation Annealing Techniques. Key algorithmic operations include individual representation, initialization, fitness function computation, selection, crossover, mutation, and ending conditions. The DG optimal power flow problem is explored with a focus on minimizing generation costs, improving voltage profiles, minimizing losses, enhancing reliability, integrating renewable energy, reducing environmental impact, managing congestion, and ensuring compliance with operational constraints. Beyond traditional considerations, the study emphasizes neglected objectives and constraints, such as cyber-security concerns, real-time operation, regulatory frameworks, social acceptance, lifecycle environmental impact, grid resilience, data privacy, aging infrastructure compatibility, and economic viability.

Mesenchymal stem cells (MSCs) hold immense therapeutic potential due to their regenerative and immunomodulatory properties. However, to utilize this potential, it is crucial to optimize their in vitro cultivation conditions. Three-dimensional (3D) culture methods using cell-laden hydrogels aim to mimic the physiological microenvironment in vitro, thus preserving MSC biological functionalities. Cellulosic hydrogels are particularly promising due to their biocompatibility, sustainability, and tunability in terms of chemical, morphological, and mechanical properties. This study investigated the impact of (1) two physical crosslinking scenarios for hydrogels derived from anionic cellulose nanofibers (CNF) used to encapsulate adipose-derived MSCs (adMSCs) and (2) physiological culture conditions on the in vitro proliferation, differentiation, and extracellular vesicle (EV) production of these adMSCs. Our results revealed that additional Ca2+-mediated crosslinking, intended to complement self-assembly and gelation of aqueous to-CNF in the adMSC cultivation medium, adversely affected both the mechanical properties of the hydrogel spheres and the growth of the encapsulated cells. However, cultivation under dynamic and hypoxic conditions significantly improved the proliferation and differentiation of the encapsulated adMSCs. Furthermore, we demonstrated that adMSCs in CNF hydrogel spheres exhibited potential for scalable EV production with potent immunosuppressive capacities in a bioreactor system. These findings underscore the importance of physiological culture conditions and the suitability of cellulosic materials for enhancing the therapeutic potential of MSCs. Overall, our study provides valuable insights for optimizing the in vitro cultivation of MSCs for various applications, including tissue engineering, drug testing, and EV-based therapies.

In the proposed article, the issues of increasing the synchronizing ability of the system of coordinated rotation of asynchronous motors are considered. Based on the T-shaped equivalent circuit, electromechanical relationships were obtained with changes in the value of the total rotor resistance and the supply voltage of individual motors. An algorithm for calculating the torques, stator and rotor currents of the motors of the system has been compiled. Based on the calculations obtained, the mechanical characteristics of the system asynchronous motors are constructed for various values of total resistance, supply voltages and rotor positions. The obtained data and graphs confirm the adequacy of the theory obtained in an analytical way. Functional and structural diagrams in small scales have been compiled, which allow simulating transient operation modes of multi-motor asynchronous electric drives in the Matlab application package. Multi-motor asynchronous electric drives with adjustable supply voltages, as well as with preliminary synchronization and synchronous braking, have been developed. Compilation of a program for the stability of a nonlinear system of a multi-motor asynchronous electric drive (MAEDs) with a thyristor voltage converter (TVC) in Matlab. Also, the modes of soft start, load shedding and surge on the motor shaft are simulated, confirming the stability of the system.

Enzyme catalysis has traditionally been used by various human cultures for creating value, long before its basic concepts have been uncovered, by preparing useful products through the trans-formation of raw materials available from natural resources. Tremendous scientific and techno-logical progress has been accumulated globally in understanding what constitutes an enzyme, what reactions enzymes can catalyze, and how to search, develop, apply and improve enzymes to make desired products. The exquisite properties of enzymes as nature's preferred catalysts, such as high selectivity, diversity and adaptability, enable their optimal work, whether in single reactions or in multiple reactions. Excellent opportunities for resource efficient manufacturing of compounds needed are provided by the actions of enzymes working in reaction cascades and pathways within the same reaction space, like molecular robots along a production line. Enzyme catalysis plays an increasing role for industrial innovation and responsible production in various areas, such as green and sustainable chemistry, industrial or white biotechnology. Sources of inspiration can be current manufacturing or supply chain challenges, the treasure of natural enzymes or the opportunities of engineering tailor-made enzymes. Making best use of the power of enzyme catalysis is essential for changing the way how current products are manufactured, how renewable biobased resources can replace fossil-based resources, and how the safety, health environment aspects of manufacturing processes can be improved towards cleaner and more sustainable production.

Organic soil amendments, such as composts, mitigate the environmental burdens associated with wasting organic resources. Although compost application to soil enhances an agroecosystem's capacity to store carbon and produce food, studies investigating the agronomical efficacy and their ability to ameliorate drought stress when used as a soil amendment are minimal. In this study, we produced and used a nutrient rich co-compost through the composting of sludge, a nitrogen-rich organic material with carbon rich municipal solid wastes (MSW) to evaluate the agronomic efficacy of the MSW derived co-compost and their ability to ameliorate drought stress. Application of co-compost significantly enhanced growth and yield of lettuce and maize, by a magnitude comparable to chemical fertilizers. Furthermore, under drought stress, lettuce plants grown under co-compost soil amendment grew much better with less wilting, more biomass and yield, and improved root growth. Also, co-compost application enhanced relative root mass ratio (RRMR) under drought stress, indicative that co-compost amendment increased the allocation of biomass to the roots, which is an important morphological attribute for drought adaptability. K content in both leaves and roots of plants amended with co-compost was also higher under drought stress, which may have played a role in osmotic adjustment, consequently, the plants exhibited higher leaf relative water content (RWC). Other nutrient elements that were significantly enhanced by co-compost application included Mg, Ca, Fe and Cu. These results provide evidence that MSW co-composting could optimize organic resource recycling for climate change mitigation and agricultural productivity while minimizing nutrient losses from agroecosystems.

Successful translation of biofortified orange maize (BOM) to a household staple food is dependent on farmers’ ability to cultivate the maize and it subsequent utilization. In this study, we assessed farmers ‘allocation of their land to cultivation of BOM and con-ventional white maize (CWM) varieties in districts where AFI-KEPO Nutrition Program is implemented in Malawi. Results show farmers were skeptical of allocating more land to cultivation of BOM. CWM was allocated significantly more land (1.75 ± 0.51 acres) than BOM (1.12 ± 0.32 acres) (p

Quantifying different stocking rates effects in three study areas placed at Mediterranean forest (Cuenca, Spain) was conducted by applying a multiparametric soil quality index, SQI, developed in undisturbed forest soils (> 40 years). The main objective is to advance in the development and application of multiparametric indexes which allow for soil condition assessment. For it, is analyse the effectiveness of a multiparametric soil quality index (SQI) as an indicator livestock impacts on the soil in mediterranean forests. Control areas without stocking rates were compared in forest stands with different age (Thicket forest stand, < 30 years; High polewood forest stand, 30-60 years; Old growth forest stand, > 60 years); with various intensity grazing areas (permanent livestock passage: inactive sheepfold for 2-3 years, and active sheepfold; intermittent livestock passage: bare soil, pine stand, scrubland). The multiparametric soil quality index (SQI) applied sensitive to changes in forest ecosystems depending of different stocking rates. However, for even more preci-sion to assess cattle alteration, multiparameter index recalibrated, creating a new one; Soil Status Index by Livestock (SSIL). Correlation between quality ranges obtained with both indexes in dif-ferent study areas suggest that SSIL can be considered a livestock impact reference indicator in Mediterranean forest soils.

Photovoltaic modules should pass series of tests and examinations, verifying the electrical and thermal characteristics of the module, before being released to the market, examining the properties of the modules should undergo appropriate durability and efficiency tests under real outdoor conditions with exposure to climatic conditions and under laboratory conditions. The performance of photovoltaic cells depends on many factors, such as solar irradiance, module operating temperature, installation location, weather conditions and module shading. In this paper, three selected photovoltaic modules were examined using a large-scale steady-state solar simulator. The current-voltage (I-V) characteristics of the photovoltaic modules were experimentally tested and analyzed. The next step was to implement a three-layer artificial neural network model (MLP). The experimental data obtained in the previous step coupled with output data from MLP were then used in global sensitivity analysis (GSA). Experiments carried out on a large-scale stationary solar simulator showed differences between the values declared by the manufacturer and the values obtained from measurements of PV modules. The first module tested achieved the maximum power point greater than that specified by the manufacturer, while the other two showed power drops; it was 85-87% for the second module, and 95-98% for the third, respectively. The performed global sensitivity analysis (GSA) for the MLP model showed that the parameters: eff (22.9) and Voc/V (14.19) have the largest effect on the power-voltage relationship, while U (7.29) has the smallest effect. The usefulness of machine learning (ML) methods in the comparative analysis of PV modules has been proved.

Energy imports and the transition to renewable energy sources are of critical importance in the current geopolitical context, which necessitates concrete actions to tackle the energy crisis at the European Union level. The study aims to explore the impact of imported non-renewable energy resources on the EU-27 economy. It examines the correlations and causal relationships between GDP, GVA, R&amp;D investments, and energy imports from 2000 to 2021. Data normality was assessed using the Shapiro-Wilk test, while Pearson's test identified correlations between variables. Linear and multiple regression analyses were conducted to determine the effects of changes in independent variables on dependent variables. The study found a strong association between natural gas imports and GDP, with increases in GDP leading to a more than fourfold rise in imports. Furthermore, multiple regression analysis indicated that a 1% increase in R&amp;D investments results in a 2.21% decrease in fossil fuel imports in 91.7% of cases. This suggests that R&amp;D investments contribute to improved efficiency and the use of renewable energy sources.

Due to the optical properties of the Electron Transport Layer (ETL) and Hole Transport Layer (HTL), inverted perovskite solar cells can perform better than traditional perovskite solar cells. It is essential to compare both types to understand their efficiencies. In this article, we studied inverted perovskite solar cells with NiOx/CH3NH3Pb3/ETL (ETL = MoO3, TiO2, ZnO) structures. Our results showed that the optimal thickness of NiOx is 80 nm for all structures. The optimal perovskite thickness is 600 nm for solar cells with ZnO and MoO3, and 800 nm for those with TiO2. For the ETLs, the best thicknesses are 100 nm for ZnO, 80 nm for MoO3, and 60 nm for TiO2. We found that the efficiencies of inverted perovskite solar cells with ZnO, MoO3, and TiO2 as ETLs, and with optimal layer thicknesses, are 30.16%, 18.69%, and 35.21%, respectively. These efficiencies are 1.5%, 5.7%, and 1.5% higher than those of traditional perovskite solar cells. Our study highlights the potential of optimizing layer thicknesses in inverted perovskite solar cells to achieve higher efficiencies than traditional structures.

The decarbonization of the electricity grid as one among the actions to reduce fossil fuel emissions, and thus their impact on global warming in the future, will be achieved mainly via the integration and widespread diffusion of renewable power sources. This is going to be supported also by the shift from the paradigm production-transmission-distribution, where electricity production oversees large-size power plants, to renewable-based distributed/diffused production, where electricity is generated very close or even by the same (group of) user(s) (or prosumers in the latter case). The number of mid-/small-size installations based on renewable energy technologies will therefore increase substantially, and the related renewable generation will be dominant against that from large-size power plants. Unfortunately, this will reduce the reliability of the grid very likely, unless appropriate countermeasures are taken/implemented, hopefully at the same time the paradigm shift is being achieved. To this aim, it is important to identify the anomalies and main fault causes that might determine in renewable-based power systems. This paper surveys the current state-of-the-art on anomalies and faults affecting wind-PV-storage hybrid power systems, i.e., the main renewable technology ensemble that will establish the future grid, and highlights possible research directions that may help to fill the literature gaps.

Evapotranspiration is a critical component of the hydrological cycle, and it has a decisive impact on the ecosystem balance in arid and semi-arid regions. The Yinchuan Plain, located in the Gobi of Northwest China, has a strong surface ET. In order to assess the ET pattern in this region, we obtained the ETa of Yinchuan Plain between 1987 and 2020 using the GEE platform. We employed the Surface Energy Balance Model (SEBAL), specifically geeSEBAL, to analyze the change pattern of ET over different seasons, years, and land types. The results show that: ① In spring, the daily ETa of the Yinchuan Plain is highest in the central lake wetland area, with a maximum value of 4.32 mm day-1. In summer, it is concentrated around the croplands and water bodies, with a maximum value of 6.90 mm day-1; In Autumn and winter, it is mainly concentrated around the water bodies and impervious areas, with maximum values of 3.93 and 1.56 mm day-1, respectively. ② From 1987 to 2020, the ET of the Yinchuan Plain showed an obvious upward and downward trend in some areas with significant land use changes, but the overall ET of the region remained relatively stable without dramatic fluctuations. ③ The evapotranspiration of different underlying land use types in the Yinchuan Plain region is as follows: water body&gt;cultivated land&gt;impervious&gt;grassland&gt;bare land. Our results showed that geeSEBAL is highly applicable in the Yinchuan Plain area. It allows for the accurate and detailed inversion of ET in the study area, which facilitates the study of regional hydrological cycle and water governance.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (&gt;0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (&lt;0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size &gt;100 μm, and soil structure was the most stable.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

This paper examines the impact of renewable energy heating on air quality in northern China, using the Qinling Mountains-Huaihe River line as a quasi-natural experiment to distinguish between regions with central heating and those without. Employing a difference-in-differences approach and analyzing panel data from 299 cities between 2014 and 2022, our findings indicate that the renewable energy heating policy has significantly improved air quality. Specifically, the policy led to substantial reductions in the Air Quality Index (AQI) and concentrations of key pollutants: SO2 by 28.31%, CO by 7.57%, NO2 by 5.72%, and PM2.5 by 7.15%. The policy's effects are most pronounced in regions with lower temperatures and in the eastern parts of the country. Further analysis emphasizes the critical role of energy transition, environmental regulations, and government investment in technology as key drivers of these air quality improvements.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Deep Learning (DL) oriented document processing is widely used in different fields for extraction, recognition, and classification processes from raw corpora of data. The article examines the application of deep learning approaches, based on different neural network methods, including Gated Recurrent Unit (GRU), Long Short-Term Memory (LSTM), and Convolutional Neural Networks (CNN). The compared models were combined with two different word embedding techniques, namely: Bidirectional Encoder Representations from Transformers BERT and Gensim Word2Vec. The models are designed to evaluate the performance of architectures based on neural network techniques for the classification of CVs of Moroccan engineering students at ENSAK(National School of Applied Sciences of Kenitra, Ibn Tofail University). The used dataset included resumes collected from engineering students at ENSAK in 2023 for a project on the employability of Moroccan engineers in which new approaches were applied, especially machine learning, deep learning, and big data. Accordingly, 867 resumes were collected from five specialties of study (Electrical Engineering, Networks and Systems Telecommunications, Computer Engineering, Automotive Mechatronics Engineering, Industrial Engineering). The results revealed good performance of the proposed models based on the BERT embedding approach compared to models based on the Gensim Word2Vec embedding approach. Accordingly, the CNN-GRU/Bert model achieved slightly better accuracy with 0.9251 compared to other hybrid models.

Electronic waste generation has been following a continuously rising trend. With electronics containing a myriad of materials some of which are hazardous, toxic, extremely rare or precious combined with more stringent legislative laws which encourage the reuse and optimised recycling of the materials included in e-waste, the need for a holistic approach is inevitable. Such an approach should not only identify the materials found in the various types of e-waste and their respective quantities but also needs to highlight the possible handling techniques and their respective impacts and associated hazards whether to the environment or human health. Performing such a task manually would be exasperating and costly while requiring extensive resources which might not be met with a justifiable economic gain; thus, the use of the advancement in computational sustainability to draw a complete picture and aid in an informed decision-making process is crucial. The e-waste ontology developed in this paper is one way of addressing the problem since it covers the treatment domain, the hazard and the materials contained within the different types of e-waste. The ontology developed can be used directly from the protégé software or by embedding it into a developed Decision Support System.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

The growing demand for high-power DC Fast Charging (DCFC) stations for Electric Vehicles (EVs) is expected to lead to increased peak power demand and reduction of grid power quality. To maximize the economic benefits and station utilization under practical constraints set by regulatory authorities and DCFC station operators, this study explores and provides methods for connecting DCFC stations to the grid employing low power interconnection rules and Distributed Energy Resources (DERs). The system uses automotive Second Life Batteries (SLBs) and Photovoltaic (PV) systems as energy buffers and local energy resource to support EV charging and improve the station techno-economic feasibility through load shifting and charge sustaining. The optimal sizing of the DERs and the selection of the grid interconnection topology is achieved by means of a Design Space Exploration (DSE) by means of exhaustive search approach to maximize the economic benefits of the charging station and to mitigate high-power demand to the grid. Without loosing of generality, this study considers a range of DER sizes, grid interconnection specifications, and related electricity tariffs of American Electric Power (AEP) Ohio and the Public Utility Commission of Ohio (PUCO). Various scenarios and strategies have been defined to account for the interconnection requirements of the grid to the DCFC with DERs. The system’s techno-economic performance of different scenarios has been analyzed and compared using a multitude of metrics.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.

The growth of photosynthetic organisms requires specific ranges of temperature and photosynthetically active radiation that are technically difficult to achieve and control, especially in outdoors cultures. In such cases, a typical meteorological sequence can be a useful tool to estimate the growth of photosynthetic organisms. This work proposes a new methodology based on long-term meteorological sequences to simulate the growth of photosynthetic organisms. A case of study that addresses the simulation of the growth of microalgae (Chlorella vulgaris) in Riosequillo, north of the Madrid region (Spain), is shown for the four seasons of the year, and these estimates are then compared with the observed results of an experimental microalgae culture in domestic wastewater. The results also show great agreement with the probability distribution function of the biomass concentration per day, obtaining the best results for typical meteorological sequences of summer and spring. The methodology seems to confirm the representativeness of typical meteorological sequences and also allows the identification of the most likely production scenarios for the feasibility analysis of projects, which has potential application in decision-making processes.

Maize is the staple cereal in Malawi, with a daily per capita consumption of 383g (dry matter basis), primarily consumed as dehulled maize flour used to cook nsima, a thick porridge. However, the extent of mass and nutrient loss during dehulling remains unclear in this food-insecure country, where the household maize harvest typically lasts only 6–7 months. In the current study, a milling experiment to determine yield and micronutrient losses was conducted. Milling batches (30 kg) of four maize grain varieties were dehulled at three abrasive disk dehullers under controlled conditions. Mass losses ranged from 18.8% to 42.7%, with a mean of 28.2±5.7%. Maize variety and dehuller significantly affected mass loss (p&lt;0.05). Initial protein, iron, and zinc concentrations were 8.8 ±1.0 g/100g, 20.5±2.0 µg/g, and 18.2 ±2.6 µg/g, respectively. Post-dehulling nutrient true retention varied for protein (49.7% to 75.6%, mean=64.7±7.0%), iron (18.7% to 71.6%, mean=37.6±12.0 %), and zinc (11.0% to 46.2%, mean=27.9±8.7 %). Maize variety significantly influenced mass and protein loss (p &lt; 0.05), while dehuller influenced mass, iron, and zinc losses. However, no significant difference (p &gt; 0.05) was found in the interaction between dehullers and variety on mass and nutrient losses, respectively. Given Malawi's precarious food insecurity situation, transitioning from dehulled maize flour nsima to whole maize flour or less refined nsima, is imperative. Our study findings can have food and nutritional savings for other southern Africa countries where the dehulling practice is rampant.

Plastic materials have revolutionized modern life, particularly in the domain of food packaging, owing to their versatility, lightweight nature, and ease of processing. However, the environmental ramifications of non-degradable plastics have raised concerns. Polylactic acid (PLA), derived from renewable sources, presents a sustainable alternative due to its biodegradability and exceptional barrier, mechanical, and safety properties. Nevertheless, the high UV transmittance of PLA limits its use for photosensitive food and pharmaceutical packaging, where UV radiation can lead to nutritional loss and spoilage. Various methods have been explored to enhance the UV-blocking capabilities of PLA, including the integration of inorganic nanoparticles and surface coatings. Despite advancements, these approaches often compromise the inherent transparency of PLA. Incorporating large conjugated groups can maintain transparency but introduces additional challenges. This paper reviews modification methods to enhance PLA's UV-barrier properties and anticipates its expanded utility in food and drug packaging, promoting UV resistance and diversifying PLA's applications.

Urban air pollution is a critical global environmental issue, necessitating an understanding of the spatiotemporal characteristics and driving factors for effective environmental protection and urban planning. This study introduced an advanced air quality assessment system that integrates environmental, socio-economic, and urban layout factors, addressing gaps in traditional models that often overlook the impact of urban spatial structures. Analyzing air quality data from Beijing's main urban area (2016-2020) alongside multi-source geographic data, the research develops a comprehensive evaluation system, incorporating 14 key driving factors. Employing Geographically Weighted Regression (GWR) and Multi-scale Geographically Weighted Regression (MGWR), the study quantitatively assessed the influence and spatial heterogeneity of these factors. Findings revealed an annual improvement in air quality, with a U-shaped seasonal pattern and significant spatial clustering (Global Moran’s I = 0.922). The MGWR model, in particular, provided a superior fit over GWR, effectively capturing the spatial variability of factors. Variables such as NDVI), economic output (GDP), and humidity space adjustment capability (HSAC) showed significant positive spatial impacts on air quality, while population density (POP), temperature (TEMP), and road density (RD) exhibited negative effects. These insights enhance the understanding of air pollution dynamics and aid in refining urban planning strategies.

Grain quality, cooking quality and nutritional quality traits are some of the major attributes that enhance uptake and utilisation of improved cowpea varieties. Therefore, there is need for a better understanding of the genetic variation and inter-relationships among these quality traits in cowpea to integrate them in cowpea breeding programs. The study was conducted to determine genetic variability among 306 cowpea genotypes for grain quality, cooking quality and nutritional quality traits and to understand the interrelationships among these traits for exploitation in breeding programs. The results showed highly significant differences (P

All hydropower project type requires an ample availability of stream flow data. Unfortunately most of the hydropower projects especially small hydropower projects are conducted on ungauged river and consequently hydrologists have for a longtime used stream flow estimation methods using the mean annual flows to gauge rivers. Unfortunately flow estimation methods which include the runoff data method, area ratio method and the correlation flow methods employ a lot of assumptions which affect their uncertainty. Although hydropower energy is one of most promising clean energy technologies available, it has potential drawbacks as compared with various other forms of renewable energy, such as biomass, solar and wind energy, due in particular to it high capital investment costs. For most of the rural population in Mozambique, access to conversional energy in the form of electricity is limited. The aim of the present investigation was to analyze the functions of the Chua micro-hydropower plant in the Manica district in Mozambique and to examine the possibility of increasing energy production there. The total power generation capacity currently installed in Mozambique is about 939 MW. Hydropower accounts for 561 MW or 61% of this, oil and natural gas in turn, for 27% and 12% of it, respectively.

Microcystis-dominated cyanobacterial blooms (MCBs) frequently occur in freshwaters worldwide due to massive Microcystis colonies formation and severely threaten human and ecosystems health. Quorum sensing (QS) is a direct cause of Microcystis colonies formation, possibly regulating MCBs occur and Microcystis population behaviors [1, 2]. Many novel findings in fundamental knowledge of Microcystis QS phenomenon and the signaling molecules have been documented. However, little effort has devoted to comprehensively summarize and discuss research progresses and exploration direction on QS signaling molecules-mediated QS system in Microcystis. This article summarizes action process of N-acyl homoserine lactones (AHLs) as major signaling molecules in Microcystis and discussed the detailed roles of AHLs-mediated QS system in cells aggregation, colonies formation, ecological adaptability and competitive advantage. And the progress was summarized in research on the QS mechanism in Microcystis. Compared to other QS system, the LuxI/LuxR-type QS system is more likely to found in Microcystis. Also, we introduced Quorum quenching (QQ) — QS blocking process in Microcystis, with emphasizing on the potential of QS inhibitors in MCBs control. Finally, in response to the research deficiencies and gaps in Microcystis QS and QQ, we proposed several future research directions in these fields. This review may deepen the understanding of Microcystis QS knowledge and provide theoretical guidance for the development of strategies to monitor, control and harness MCBs.

Metabolites present in the hemolymph of honey bees play a crucial role in modulating the metamorphic process within the species. However, the precise alterations in metabolite composition, along with the associated variances and regulatory pathways implicated during the larvae-to-pupae metamorphosis of honey bees, remain incompletely elucidated. In this investigation, we gathered hemolymph samples from honey bee larvae at three distinct physiological stages-feeding, prepupal, and pupae and subjected them to metabolite analysis utilizing the liquid chromatography-mass spectrometry (LC-MS) technique. Employing principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA), we identified significant differential metabolites and conducted a metabolic pathway analysis on those differentially up-regulated during the prepupal and pupae stages. Notably, metabolites up-regulated in the hemolymph of prepupal stage larvae primarily governed glucose metabolism and fat digestion and absorption, while those in pupae stage larvae were involved in regulating chitin and lipopolysaccharide precursor formation, as well as the biosynthesis of phenylalanine, tyrosine, and tryptophan. These findings bear significant implications for advancing our comprehension of the metamorphic processes in honey bees.

Viral contamination in the aquaculture industry is a significant challenge that requires further research. Emerging evidence suggests that long noncoding RNAs (lncRNAs) play a role in regulating various biological processes, including immunity. However, most studies have focused on model organisms, and little is known about non-coding RNAs in the immune response to viral hemorrhagic septicemia (VHS) in rainbow trout. In this study, we investigated the listing of non-coding RNAs (ncRNAs) in rainbow trout challenged with VHS virus. We explored their potential role in defense-like responses based on transcriptomic analysis of the virus-treated and control groups. As a result of this research, 4207 lncRNAs were identified, of which 182 lncRNAs were differentially expressed between treated and untreated samples. Among 7753 lncRNA transcripts, 1920 were novel intergenic (class code “u”), and 3748 transcripts were potentially novel isoform of lncRNAs. Gene ontology analysis revealed biological pathways associated with the stress response and immune signaling. Pairs of genes such as TP63-MSTRG.62, IL10-MSTRG.9783, IL10-MSTRG.9784, TK1-MSTRG.22826, and MSTRG.17881-GLI1 showed cis interactions, while DOCK10-MSTRG.30015, MSTRG.36357-LOC101268921, and MSTRG.34190-ENPP2 showed trans interactions. In this study, the role of lncRNAs in regulating the expression of the target genes was clearly identified. This finding is consistent with the regulatory processes of immune system responses mediated by cytokines, as well as the regulation of oxygen levels in response to viral infection. The information presented here highlights the various regulatory mechanisms of lncRNAs in the expression of immune system genes in fish treated with VHS virus.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

Acetic acid bacteria (AAB) are major contributors to the production of fermented vinegar, offering various cultural, culinary, and health benefits. Although the residual unpasteurized AAB after vinegar production are not pathogens, these are necessary the safety evaluations including antibiotic resistance for the use as starters. In this research, we investigated the antibiotics resistance profiles of 26 AAB strains, including various species of Komagataeibacter and Acetobacter, against ten different antibiotics using the E-test method. All strains exhibited resistance to aztreonam and clindamycin. Komagataeibacter species demonstrated a 50% resistance rate to ciprofloxacin, analogous to Acetobacter species, but showed twice the resistance rates to chloramphenicol and erythromycin. Genomic analysis of K. saccharivorans CV1 identified intrinsic resistance mechanisms, such as multidrug efflux pumps, thereby enhancing our understanding of antibiotic resistance in acetic acid-producing bacteria. These findings enhance understanding of antibiotic resistance in AAB for food safety and new antimicrobial strategies, suggesting the need for standardized testing methods and molecular genetic study.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

Crops obtained by genome editing (GE) technologies represent a notable and disruptive shift from genetically modified or transgenic plants, outpacing public perception and regulatory frame-works. Multiple aspects of GE are contributing to the advancement of modern agriculture, in-fluencing the market structure by introducing specific changes within the existing genetic blue-print of an organism. Generally, the GE toolbox includes distinct technologies able to incorporate site-specific and pre-determined genomic modifications, exploiting well-established genetic modification strategies. For these reasons, GE-derived approaches are considered new plant breeding methods, known as new breeding techniques (NBTs). Particularly, CRISPR/Cas-based technologies represent a considerable improvement over prior techniques, being more precise, accurate and straightforward for targeted gene editing, in a reliable and reproducible way, with numerous applications. CRISPR/Cas system exploitation for non-editing purposes has also been widely documented, ranging from cell imaging to expression regulation and DNA assembly. Recently, CRISPR/Cas systems have been employed for target detection and could be used to ef-ficiently identify multiple organic chemicals. High-sensitivity and high-specificity detection are two main points of the CRISPR/Cas technology, without needing complex expertise or technical pipelines. This manuscript aims to provide an overview of the main advances of CRISPR/Cas-based systems into new frontiers of non-editing. The associated implications (e.g., molecular traceability) and their relative impacts are also presented and discussed.

Small peptides (SPs), ranging from 5 to 100 amino acids, play integral roles in plants due to their diverse functions. Despite their low abundance and small molecular weight, SPs intricately regulate critical aspects of plant life, including cell division, growth, differentiation, flowering, fruiting, maturation, and stress responses. As vital mediators of intercellular signaling, SPs have garnered significant attention in plant biology research. This comprehensive review delves into SPs' structure, classification, and identification, providing a detailed understanding of their significance. Additionally, we summarize recent findings on the biological functions and signaling pathways of prominent SPs that regulate plant growth and development. The review also offers a forward-looking perspective on future research directions in peptide signaling pathways.

Lignin is insoluble in water, limiting its use in the synthesis of adhesives. Therefore, in order to increase the amount of lignin raw materials used in the synthesis of adhesives, a kind of aminated lignin compounds was prepared through lignin amination reaction, and conducting structural analysis in this paper. The particle size of the amino lignin is about 100 nm, with the weight average molecular weight of 57,627 g/mol and a water solubility of 0.45g/100ml. The reaction mechanisms were proposed that the phenolic hydroxyl groups of lignin react with ammonia molecules, and thereby successfully introducing amino groups to generate the aminated lignin compounds. Therefore, this article enriches the scientific theory of lignin reactions and provides reference for the widespread application of lignin raw materials in the field of adhesives.

Hyperspectral images (HSI) contain abundant spectral information. Efficient extraction and utilization of this information for image classification remain prominent research topics. Previously, hyperspectral classification techniques primarily relied on statistical attributes and mathematical models of spectral data. Deep learning classification techniques have recently been extensively utilized for hyperspectral data classification, yielding promising outcomes. This study proposes a deep learning approach that uses polarization feature maps for classification. Initially, the polar coordinate transformation method is employed to convert the spectral information of all pixels in the image into spectral feature maps. Subsequently, the proposed Deep Context Feature Fusion Network (DCFF-NET) is utilized to classify these feature maps. The model is validated using three open-source hyperspectral datasets: Indian Pines, Pavia University, and Salinas. The experimental results indicated that DCFF-NET achieves excellent classification performance. Experimental results on three public HSI datasets demonstrate that the proposed method accurately recognizes different objects with an overall accuracy (OA) of 86.68%, 94.73%, and 95.14% based on the pixel method, and 98.15%, 99.86%, and 99.98% based on the pixel-patch method.

The Sanhetun tellurium-gold (Te-Au) deposit, located in the Duobaoshan polymetallic metallogenic belt (DPMB) within the eastern section of the Central Asian Orogenic Belt (CAOB), is a newly discovered small scale gold deposit. The mineralization, with resource of ≥ 4t Au, is mainly hosted in 3 NNE-trending alteration zones between granitic mylonite and volcanogenic-sedimentary formations. It’s the genesis and timing of formation of this deposit are poorly constrained. Here, we report the results of petrographic studies, TESCAN Integrated Mineral Analyzer (TIMA), major and trace element concentrations, and in situ S isotope of pyrite and U-Pb ages of calcite. The results show that there are five species of telluride, including native tellurium, tetradymite, tsumoite, hessite and petzite and four types of pyrite, including coarse-grained euhedral Py1, fine-grained quartz-Py2 vein crosscutting Py1 and anhedral aggregated Py3 and Py4. The pre-ore Py1, containing negligible Au, Te and other trace elements, have a relatively narrow range of δ34S values ranging from -1.20 to -0.57‰. The Py2 have slightly high concentrations of Au and Te and distinctly high concentrations of Mo, Sb, Zn and Mn with markedly positive δ34S values of 4.67 to 14.43‰. The main ore stage Py3 contains high Au and Te concentrations and shows narrow δ34S values ranging from -5.69 to 0.19‰. The post-ore stage Py4 contains low Au concentrations with the δ34S values ranging from 2.66 to 3.86‰. Calcite from ore stage yield a U-Pb age of 135 ± 22 Ma, interpreted as the age of Te-Au mineralization. Our geochemical and geochronological data indicate that the Te was derived from partial melting of mantle metasomatized by the Te-rich fluids that originated from oceanic sediments. We correlate the tectonic setting with the subduction of Paleo Pacific plate in Early Cretaceous.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

This study aims to find countries that differ in their development of the agricultural sector in terms of environmental care and to examine the relationship between renewable and non-renewable energy consumption and agricultural sector production in European Union countries. The classification of countries was conducted using the principal component method and biplot. Panel data for the period 2000-2022 and a VAR model, an impulse response function (IRF) and causality tests were used for the study. The results indicate two distinct groups of countries that significantly differ in adopting green agricultural practices. Only seven EU countries stand out for sustainable agriculture with low pesticide use, a significant share of organic farms and high use of renewable energy in agriculture. Energy consumption affects agricultural production differently in the two groups of countries studied: in countries with sustainable agriculture, an increase in renewable energy consumption translates into a positive increase in agricultural production. On the other hand, an increase in non-renewable energy consumption shows a dampening effect on agricultural production growth, especially in countries with less sustainable agriculture. The study results highlight the need to promote renewable energy development in agriculture and raise awareness about the adverse environmental effects of intensive agriculture while emphasising the positive impact of organic agriculture on agricultural production.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

The toxic cadmium (Cd) poses a serious threat to plant growth and human health. Populus euphratica CPK21 has previously been shown to attenuate Cd toxicity by reducing Cd accumulation, enhancing antioxidant defense and improving water balance in transgenic Arabidopsis. Here, we confirmed a protein-protein interaction between PeCPK21 and AtNF-YC3 by yeast two-hybrid, HaloTag pull-down and bimolecular fluorescence complementation assays. AtNF-YC3 was induced by Cd and strongly expressed in PeCPK21-overexpressed plants. Overexpression of AtNF-YC3 in Arabidopsis reduced salt inhibition of root length, fresh weight and membrane stability under Cd stress conditions (100 µM, 7 d), suggesting that AtNF-YC3 appears to contribute to the improvement of Cd stress tolerance. AtNF-YC3 improved Cd tolerance by limiting Cd uptake and accumulation, activating antioxidant enzymes, and reducing H2O2 production under Cd stress. We conclude that PeCPK21 interacts with AtNF-YC3 to limit Cd accumulation, enhance the ROS scavenging system, and thereby positively regulate plant adaptation to Cd environments. This study highlights the interaction between PeCPK21 and AtNF-YC3 under Cd stress conditions, which can be utilized to improve Cd tolerance in higher plants.

Spray penetration into citrus canopies is critical for adequate coverage and deposition to ensure effective pest control. However, mismatch of air assistance to target canopy characteristics can lead to unintended spray loss through over penetration. To evaluate the effect of air assistance on on-target deposition, two sprayers (surrogates for airflow rates) were used to apply a fluorescent tracer dye solution @ target concentration of 300 ppm to 16 medium foliage density tree blocks in a commercial mandarin orchard. The complete factorial experiment in three replications comprised two ground speeds (1.6 and 4.8 km/h), two disc-core nozzles (TeeJet® D3-25 and D6-45), and either one or two nozzle rows to obtain a wide range of application rates (496 to 9,719 L/ha). Dye deposition significantly decreased with canopy depth (p=&lt;0.001) by nearly 7 times across the 3.4-m-wide canopies but was not significant over 1.2 to 2.2 m sampling height (p=0.867). Deposition obtained with the low airflow rate sprayer was significantly greater (p=&lt;0.001) than that obtained with the high airflow rate sprayer over the dose range likely due to too much air pushing out spray droplets. This study underscores the importance of matching the air assistance of orchard sprayers to the target canopy.

This study develops a structure for mapping native vegetation in a transition area between Brazilian Cerrado and Atlantic Forest from integrated spatial information from the Sentinel-1 and Sentinel-2 satellites. Most studies use this data separately, however, the integrated use of optical sensors with Synthetic Aperture Radar (SAR) sensors can improve the methodology for classifying land use and land cover (LULC). The fusion of Sentinel-1 and Sentinel-2, for example, can increase the accuracy of mapping algorithms, using complementary information, such as spectral, backscattering, polarimetry, and interferometry. The study area comprises the Lobo Reservoir Hydrographic Basin, which is part of an environmental conservation unit protected by Brazilian law and with significant human development. LULC were classified, using the random forest deep learning algorithm. The classifying attributes were backscatter coefficients, polarimetric decomposition, and interferometric coherence for radar data (Sentinel-1), and optical spectral data, comprising bands in the red edge, near infrared, and shortwave infrared (Sentinel-2). The attributes were evaluated in three settings in which the SAR and optical data were evaluated separately (C1 and C2, respectively) and in an integrated manner (C3). The study found greater accuracy for C3 (96.54%), an improvement of nearly 2% compared to C2 (94.78%) and more than 40% in relation to C1 (55.73%). The classification algorithm encountered significant challenges in identifying wetlandsin C1, but performance improved in C3, enhancing differentiation by stratifying a greater number of classes during training and facilitating visual interpretation during sampling. Accordingly, the use of SAR and optical data becomes an alternative to optimize LULC mapping in tropical regions, due to the limited influence of atmosphere on images in the microwave range.

Polyalcohol liquefaction can be done by acid or basic catalysis producing polyols with different properties. This study compared the mechanical properties of foams produced using polyols from liquefied Cytisus scoparius obtained by acid and basic catalysis and using two different foam catalysts. The differences were monitored using FTIR analysis. Acid-catalyzed liquefaction yielded 95.1 %, with the resultant polyol having an OH index of 1081 mg KOH/g while basic catalysis yielded 82.5 %, with a similar OH index of 1070 mg KOH/g. Generally, compressive strength with dibutyltin dilaurate (DBTDL) ranged from 16 - 31 kPa (acid-liquefied polyol) and 12 -21 kPa (base-liquefied polyol), while with stannous octoate (TIN), it ranged from 17 - 42 kPa (acid) and 29 - 68 kPa (base). Increasing water content generally decreased the compressive modulus and strength of foams. Higher water content led to a higher absorption at 1670 cm-1 in the FTIR spectrum due to the formation of urea. Higher isocyanate indices generally improved compressive strength, but high amounts led to unreacted isocyanate that could be seen by a higher absorption at 2265 cm-1 and 3290 cm-1. DBTL was shown to be the best foam catalyst due to higher trimer conversion seen in the spectra by a higher absorption at 1410 cm-1. Acid and base-derived polyols lead to different polyurethane foams with different FTIR spectra, particularly with a higher absorption at 1670 cm-1 for foams from acid-derived liquefaction.

Timely and accurate acquisition of information on distribution of the crop planting structure in Loess Plateau of eastern Gansu Province, one of the most important agricultural areas in western China, is crucial for promoting fine management of agriculture and ensuring food security. In this study, the Object-Based Image Classification (OBIC), the Random Forest (RF) and Convolutional Neural Network (CNN) models were employed to classify the crop planting structure of four representative test areas in Qingyang City in a precise manner. Firstly, different optimal segmentation scales for various crops were selected using the Estimation of Scale Parameter 2 (ESP2) tool and the Ratio of Mean Difference to Neighbors(ABS) to Standard Deviation (RMAS)model. The images were then segmented through multiresolution segmentation combined with the Canny Edge Detection algorithm. Secondly, the L1 regularized logistic regression model was utilized to select and optimize 39 spatial feature factors including spectral, textural, geometric, and index features, in conjunction with phenological factors. Lastly, under the multi-level classification framework, the Random Forest (RF) classifier and Convolutional Neural Network (CNN) model, combined with object-based multiresolution segmentation, was used to classify the crop planting structure. The findings show that: Thanks to the Canny Edge Detection algorithm, we can obtain a more complete boundary of the segmented objects and improve the separability. The optimal segmentation scales for corn, vegetables, and buckwheat were found to be 55, 70, and 35, respectively, while wheat and apple had optimal segmentation scales of 65. In addition to phenological characteristics, the number of selected spatial features for corn, vegetables, buckwheat, wheat, and apple were 9, 7, 16, 12, and 10, respectively. The CNN model demonstrated high consistency with the RF model in the classification results, but the accuracy of RF model is higher than that of CNN model on the whole. The overall accuracy of classification using RF model in four test areas registered 91.93%, 94.92%, 89.37% and 90.68%, respectively. This paper introduced crop phenological factors, effectively improving the extraction precision of shattered agricultural planting structure in the Loess Plateau of eastern Gansu Province. Its findings have important application value in crop monitoring, management, food security and other related fields.

Droughts have a substantial effect on water resources, agriculture, and ecosystems on a worldwide scale. In the Mekong Delta of Vietnam, droughts exacerbated by climate change are significantly endangering the region's agricultural sustainability and output. Conventional forecasting techniques frequently do not capture the intricate dynamics of meteorological phenomena associated to drought effectively, prompting the exploration of more advanced methodologies. This work utilises artificial intelligence, par-ticularly machine learning methods like Gradient Boosting and Extreme Gradient Boosting (XGBoost), to enhance drought pre-diction in the Mekong Delta. The study utilises data from 11 meteorological stations spanning from 1990 to 2022 to create and evaluate Machine Learning models based on several climatic factors. We utilise Gradient Boosting and XGBoost algorithms to estimate the Standardised Precipitation-Evapotranspiration Index (SPEI) and evaluate their effectiveness in comparison to con-ventional forecasting techniques. The results show that Machine Learning, particularly XGBoost, surpasses traditional approaches in predicting SPEI accuracy at various time scales. XGBoost demonstrates skill in understanding the complex relationships between climatic factors, with R² values falling between 0.90 and 0.94 for 1-month forecasts. The progress highlights the potential of Machine Learning in improving drought management and adaptation tactics, proposing the incorporation of Machine Learning forecasting models into decision-making processes to enhance drought resistance in susceptible areas.

The Cauto River Basin (CRB), the heartland of Cuban agriculture, has been hit hard by drought and water shortage. In response to this pressing issue, this study provides a comprehensive as-sessment of water supply, demand and balance within the Cauto River Basin, considering the baseline and projected socio-economic and climatic conditions by coupling of SWAT and WEAP models. The obtained results reveal that the annual flow in the CRB is projected to slightly de-crease (2.5%) in which the reduction in the rainy season (3.1%) is higher than that in the dry sea-son (1.3%). Total water demand in the baseline scenario is around 1.194 billion m3, dominated by agriculture (96%), with rice crop requiring nearly half. For the future scenario of 2050, the study shows a 16.6% surge in demand to 1.394 billion m3, driven by climate change and agricultural expansion. However, domestic use decreases by 10% due to population reduction. Water deficit in the future is projected to increase by 52% from 172.4 to 262.7 million m3 due to rising water demand and declining water supply. This study shows that integrating a hydrological model into a water allocation model is a promising approach to estimate the water supply, demand and balance, which is a crucial component of water resources management.

Nutrition therapy is the best solution to human chronic diseases, especially beer and barley which play an important role in human health and civilization. We demonstrated the actional mechanism of functional ingredients in beer and barley to combat chronic diseases, based on PubMed, google, CNKI, and ISI Web of Science databases from 1997 to 2024. Beer is rich in functional ingredients that is a complex of barley malt and hops; the health effect of beer against 26 chronic diseases is highly similar to that of barley, due to molecular mechanism of polyphenols (phenolic acids, flavonoids), melatonin, minerals, bitter acids, vitamins, and peptides. The ancient German Beer Purity Law provides much scientific basis today, especially indirectly supporting the human one cell disease theory. Low purine beer can be produced by enzymatic and biological degradation and adsorption of purines as well as dandelion addition. Functional beer with low purine and high active ingredients made from Beer Purity and barley malt as well as functional foods addition will be the key and important development direction, such as ginger beer and ginseng beer, especially coix-lily beer at the ancestors ca. 9000 years ago. This review paper not only reveals the actional mechanism of beer overcoming human chronic diseases, but also provides scientific basis for the development of functional beer for the prevention and treatment of human chronic diseases.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Expansins are cell wall (CW) proteins that mediate the CW loosening and regulate salt tolerance in a positive or negative way. The transcription of Populus trichocarpa expansin A6 (PtEXPA6) was downregulated upon prolonged duration of salt stress (48 h) after a transient increase induced by NaCl (100 mM). The role of PtEXPA6 in salt tolerance was determined by transferring the PtEXPA6 gene into the hybrid species Populus alba × P. tremula var. glandulosa clone 84K (84K) and Populus tremula × P. alba INRA '717-1B4' (717-1B4). The PtEXPA6-transgenic poplars of 84K and 717-1B4 showed a greater reduction in photosynthesis, stem height and diameter growth under salt stress and a reduced capacity for ROS scavenging by antioxidant enzymes, which is associated with excessive Na+ accumulation in roots and shoots. NMT flux recordings showed that the radial translocation of Na+ salt into the root xylem and real-time Na+ translocation from roots to leaves were greater in PtEXPA6-transgenic poplars than in wild-type poplars. Analysis of comparative contractility and comparative extensibility of intact root tips indicated that PtEXPA6 increased the CW loosening in the transgenic poplars of 84K and 717-1B4. Noteworthy, the PtEXPA6-promoted CW loosening was shown to facilitate radial and longitudinal transport of Na+ in transgenic poplars. We conclude that overexpression of PtEXPA6 leads to CW loosening that facilitates radial translocation of Na+ into the root xylem and subsequent Na+ translocation from roots to leaves, resulting in excessive Na+ accumulation and consequently reduced salt tolerance in transgenic poplars.

Listeria monocytogenes is an emerging pathogen responsible for the serious foodborne disease, listeriosis. The commensal gut microbiota is the first line of defense against pathogen internalization. The gut microbiome can be modified by prebiotic substrates, which are frequently added to food products and dietary supplements. Prebiotics should selectively support the growth of beneficial microbes and thus improve host health. Nevertheless, little is known about their effect on the growth of L. monocytogenes. The aim of this study was to evaluate the growth ability of four L. monocytogenes strains, representing the most common serotypes, on prebiotic oligosaccharides (beta-(1,3)-D-glucan, inulin, fructooligosaccharides, galactooligosaccharides, lactulose, raffinose, stachyose, and 2´-fucosyllactose and a mixture of human milk oligosaccharides) as a sole carbon source. The results showed that only beta-(1,3)-D-glucan was metabolized by L. monocytogenes. Therefore, the safety of beta-(1,3)-D-glucan with respect to listeriosis development should be further studied.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

Current agriculture intensifies crop cultivation to meet food demand, leading to unsustainable use of chemical fertilizers. This study investigates a few physiological and agronomic responses of common wheat following the inoculation with plant growth-promoting bacteria to reduce nitrogen inputs. A field trial was conducted in 2022-23, in Legnago (Verona, Italy) on Triticum aestivum var. LG-Auriga comparing full (180 kg ha-1) and reduced (130 kg ha-1) N doses, both with and without foliar application at end tillering of the N-fixing bacterium Methylobacterium symbioticum. Biofertilization did not improve shoot growth, while it seldom increased root length density in the arable layer. It delayed leaf senescence, prolonged photosynthetic activity, amplified stomatal conductance and PSII efficiency under reduced N dose. Appreciable ACC-deaminase activity of such bacterium disclosed augmented nitrogen retrieval and reduced ethylene production, explaining ameliorated stay-green. Yield and testing weight were unaffected by biofertilization, while both glutenin-to-gliadin and HMW-to-LMW ratios increased together with dough tenacity. It is concluded that Methylobacterium symbioticum can amplify nitrogen metabolism at reduced nitrogen dose, offering a viable approach to reduce chemical fertilization under suboptimal growing conditions for achieving a more sustainable agriculture. Further research over multiple growing seasons and soil types is necessary to corroborate these preliminary observations.

Producing translucent eggs has been found to reduce the quality and safety of the eggs produced., as well as the demand from consumers. However, the intestinal function and the molecular mechanism for the production of translucent eggs remain uncertain. A total of 120 eggs were allocated into two groups, one for the translucent egg group (group T) and one for the normal group (group C), according to the degree of eggshell translucence. Translucent eggs showed thicker eggshell and lower egg yolk color. We also detected the plasma biochemical index, intestinal morphology and structure, enzyme activity, and antioxidant capacity of the hens’ producing translucent eggs and normal eggs. The results showed that the ratio of duodenal villus length to crypt depth, succinate dehydrogenase (SDH) activity, chymotrypsin, total ATPase (T-ATPase), alkaline phosphatase (AKP) and glutathione peroxidase (GSH-Px) activities were decreased in the hens produced translucent eggs (P &lt; 0.05), but malondialdehyde (MDA) content was increased (P &lt; 0.05); jejunal lipase activity, Na+K+-ATPase activity, total antioxidant capacity (T-AOC), GSH-Px activities were decreased (P &lt; 0.05) in group T; ileal amylase and Ca2+Mg2+-ATPase activities were also decreased (P &lt; 0.05) in group T. In addition, we identified a total of 471 differentially expressed genes (DEGs) in duodenal tissue, with 327 up-regulated genes and 144 down-regulated genes (|log2FC| ≥ 1 and P &lt; 0.05). Enrichment analysis showed that the up-regulated genes, such as GSTT1, GSTO2, GSTA3, were mostly enriched in metabolism of xenobiotics by cytochrome P450, drug metabolism-cytochrome P450 and oxidative phosphorylation pathways. The results of our study indicate that plasma lipid metabolism disorder, decreased intestinal antioxidant capacity, and altered intestinal metabolism capabilities may influence the formation of translucent eggs.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

The article focuses on mining of non-energy mineral resources with minimum environmental impacts. It issues from research results of a project Competence Centre for Effective and Ecological Mining of Mineral Resources implemented at the Faculty of Mining and Geology at VŠB-Technical University of Ostrava, Czech Geological Survey, a company Watrad ltd., a state enterprise Diamo, a company RPS Ostrava plc and a company Sedlecký kaolin plc. The paper starts with a partial analysis of the existing legal norms related to mining and processing of mineral resources. Next, it analyses mineral resource mining options free of negative environmental impacts. The fundamental tool to assess potential environmental impacts of mining is the implementation of Environmental Impact Assessment (EIA) process for a given mineral resource. In the Czech Republic environmental impact assessment is carried out by course of Act 100/2001 Coll. Its important amendment is Act 39/2015 Coll. claiming, inter alia, that the environmental impact assessment is rigidly connected with other permits and procedures, such as the zoning process and building construction permits. The article describes the environmental impacts of mining of non-energy mineral resources, including the following factors: appropriation of land, impacts on surface water, ground water and soil, noise, influence on the landscape character, and air pollution. The paper also includes a case study summarizing information on the environmental factors that may play a role in potential underground mining of graphite in the deposit Český Krumlov - Městský Vrch and the deposit Lazec - Křenov.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Deploying Cellular Internet of Things (CIoT) devices in urban and remote areas faces significant energy efficiency challenges. This is especially true for Narrowband IoT (NB-IoT) devices, which are expected to function on a single charge for up to 10 years while transmitting small amounts of data daily. The 3rd Generation Partnership Project (3GPP) has introduced energy-saving mechanisms in Releases 13 to 16, including Early Data Transmission (EDT) and Preconfigured Uplink Resources (PUR). These mechanisms extend battery life and reduce latency by enabling data transmission without an active Radio Resource Control (RRC) connection or Random Access Procedure (RAP). This paper examines these mechanisms using the LENA-NB simulator in the ns-3 environment, which is a comprehensive framework for studying various aspects of NB-IoT. The LENA-NB has been extended with PUR, and our analysis shows that PUR significantly enhances battery life and latency efficiency, particularly in high-density environments. Compared to the default RAP method, PUR reduces energy consumption by more than 2.5 times and increases battery life by 1.6 times. Additionally, PUR achieves latency reductions of 2.5-3.5 times. The improvements with PUR are most notable for packets up to 125 bytes. Our findings highlight PUR’s potential to enable more efficient and effective CIoT deployments across various scenarios. This study represents a detailed analysis of latency and energy consumption in a simulated environment, advancing the understanding of PUR’s benefits.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with reduced graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorpora-tion of rGO would increase the interlayer spacing of NVO and diminish the charge transfer in-teractions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 95% of its initial specific capacity of 507 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

This study explores the enhancement of aqueous zinc-ion batteries (AZIBs) using ammonium-enhanced vanadium oxide cathodes. Density Functional Theory (DFT) calculations reveal that NH₄⁺ incorporation into V₆O₁₆ lattices significantly facilitates Zn²⁺ ion diffusion by reducing electrostatic interactions, acting as a structural lubricant. Subsequent experimental validation using (NH₄)₂V₆O₁₆ cathodes synthesized via a hydrothermal method corroborates the DFT findings, demonstrating remarkable electrochemical stability with a capacity retention of 90% after 2000 cycles at 5 A g⁻¹. These results underscore the potential of NH₄⁺ in improving the performance and longevity of AZIBs, providing a pathway for sustainable energy storage solutions.

Bigeye grunt Brachydeuterus auritus is an important economic species in the waters off Sierra Leone in West Africa, with great ecological value. Based on the survey data of bottom trawl nets from 6 voyages from 2019 to 2021, the body weight-length relationship (WLR), as well as their relative fatness, were studied in depth using the method of body length and its corresponding mean body weight. This study fitted the WLR of bigeye grunt by gender, calculated its fullness, and analyzed the influence of environmental factors. The results showed that month and gender had a significant impact on body length and weight distribution (P&lt;0.01). There was a highly significant negative correlation (P&lt;0.01) between the condition factor (a) and the allometric factor (b) in the WLR, and salinity significantly affects b (P&lt;0.05). The (lga)/b ratio was less affected by environmental factors which may be related to the body size and density of the fish. The difference in b between male and female populations was extremely significant (P&lt;0.01). The relative fatness had significant seasonal variation characteristics, with highly significant effects of sex and body length (P&lt;0.01). With increasing body length, the relative fatness showed two types of changes, continuously increasing and first increasing then decreasing, with salinity and b significantly affecting the type of change (P&lt;0.05) and depth having a highly significant effect (P&lt;0.01). The bigeye grunt off the coast Sierra Leone exhibited significant seasonal growth characteristics, with significant differences in growth characteristics between male and female individuals. This study suggested that salinity may be the main factor affecting its growth and development. In addition, this study hypothesised that the peak breeding season may occur during the dry season, beginning in December and ending before April of the following year. The study provides updated and more comprehensive insights into the biology and ecology of the bigeye grunt offshore Sierra Leone, West Africa, which can provide scientific basis for its resource assessment, development and utilization, and resource management.

Cooperative and self-enforceable water allocation is a key instrument to manage geopolitical conflict induced by water scarcity, which necessitates concerning the cooperative willingness of the agents and considering their heterogeneity in geography, climate, hydrology, environment and social economy. Based on a multi-indicator system that contains asymmetric information on water volume contribution, current water consumption, water economic efficiency and efforts for eco-environmental protection, this study proposed a water allocation framework by combining the asymmetric power index approach with bankruptcy theory for solving the transboundary water allocation problem under scarcity. The proposed method was applied to the Yellow River Basin in northern China, which is mainly shared by nine provincial districts and frequently suffers from severe water shortage, and its results were compared with six alternative methods. The results highlight the necessity of quantifying agent’s willingness to cooperate under the background of asymmetric negotiation power when making decisions on transboundary water allocations. The proposed method allows to perform transboundary water allocations through simultaneous consideration of the agent’s cooperation willingness, asymmetric negotiation power as well as disagreement allocation points, which ensure the stability, fairness and self-enforceability of allocation results. Therefore, it can offer practical and valuable decision-making insights for transboundary water management under water scarcity.

A novel Gram-stain-negative, facultatively anaerobic and mixotrophic bacterium, designated as strain LZ166T, was isolated from the bathyplagic seawater in the western Pacific Ocean. Cells were short rod-shaped, oxidase- and catalase- positive, and motile by means of lateral flagella. Growth of strain LZ166T was observed at 10-45 ℃ (optimum, 34-37 ℃), at pH 5-10 (optimum, 6-8) and in the presence of 0-5% NaCl (optimum, 1-3%). Phylogenetic analysis based on the 16S rRNA gene showed that strain LZ166T shared the highest similarity (98.58%) with Aquibium oceanicum B7T, and formed a distinct branch within the Aquibium genus. Genomic characterization, including average nucleotide identity (ANI, 90.73-76.79%), average amino identity (AAI, 88.50-79.03%) and digital DNA-DNA hybridization (dDDH, 36.1-22.2%) values between LZ166T and other species within the Aquibium genus, further substantiated its novelty. The genome of strain LZ166T was 6,119,659 bp in size with a 64.7 mol% DNA G+C content. The predominant fatty acid was summed feature 8 (C18:1ω7c and/or C18:1ω6c). The major polar lipids identified were Diphosphatidylglycerol (DPG), phosphatidylethanolamine (PE), glycolipid (GL) and phosphatidylglycerol (PG), with ubiquinone-10 (Q-10) as the predominant respiratory quinone. Genomic annotation indicated the presence of genes for a diverse metabolic profile, including pathways for carbon fixation via the Calvin–Benson–Bassham cycle and inorganic sulfur oxidation. Based on polyphasic taxonomic results, strain LZ166T represented a novel species of the genus Aquibium, for which the name Aquibium pacificus sp. nov., is proposed, with the type strain LZ166T (= MCCC M28807T = KACC 23148T = KCTC 82889T).

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

The microbial communities are closely related to the overall health and quality of soil, but studies on microbial ecology in apple-pear orchard soils are limited. In the current study, 28 soil samples were collected from three apple-pear orchards in northeastern China, and the composition and structure of fungal and bacterial communities were investigated by high-throughput sequencing. Molecular ecological network showed that the keystone taxa of bacterial communities were Actinobacteria, Proteobacteria, Gemmatimonadetes, Acidobacteria, Nitrospirae, and Chloroflexi, and the keystone taxa of fungal communities was Ascomycota. Mantel tests showed that soil texture and pH were important factors shaping soil bacterial and fungal communities, and soil water soluble organic carbon (WSOC) and nitrate nitrogen (NO3--N) were also closely related to soil bacterial communities. Canonical correspondence analysis (CCA) and variation partition analysis (VPA) analysis revealed that geographic distance, soil texture, pH, and other soil properties could explain 10.55%, 13.5%, and 19.03% of the overall variation of bacterial communities, and they explained 11.61%, 13.03%, and 20.26% of the overall variation of fungal communities, respectively. The key stone taxa of bacterial and fungal communities in apple-pear orchard soils and their strong correlation with soil properties could provide useful clues toward sustainable management of orchards.

Understanding the distribution of rock glaciers provides key information for investigating and recognizing the status and changes of the periglacial environment. Deep learning algorithms and red-green-blue (RGB) bands from high-resolution satellite images have been extensively employed to map rock glaciers. However, the near-infrared (NIR) band offers rich spectral information and sharp edge features that could significantly contribute to semantic segmentation tasks, but it is rarely utilized in constructing rock glacier identification models due to the limitation of three input bands for classical semantic segmentation networks, like DeeplabV3+. In this study, a dual-encoder DeeplabV3+ network (DEDNet) was designed to overcome the flaws of classical DeeplabV3+ network (CDNet) when identifying rock glaciers using multispectral remote sensing images by extracting spatial and spectral features from RGB and NIR bands, respectively. This network, trained with manually labeled rock glacier samples from QiLian Mountains, established a model with accuracy, precision, recall, specificity, and mIoU (Mean Intersection over Union) of 0.9131, 0.9130, 0.9270, 0.9195, and 0.8601, respectively. The well-trained model was applied to identify new rock glaciers in a test region, achieving a producer's accuracy of 93.68% and a user's accuracy of 94.18%. Furthermore, the model was employed to two study areas in northern Tien Shan (Kazakhstan) and Daxue Shan (Hengduan Shan, China) with high accuracy, which proved that the DEDNet offers an innovative solution to more accurately map rock glaciers on a larger scale due to its robustness across diverse geographic regions.

The Tibetan Plateau(TP) is known as ‘the water tower of Asian’, its precipitation variation play an important role in the eco-hydrological processes and water resources regimes. based on the monthly mean precipitation data of 65 meteorological stations over the Tibetan Plateau and the surrounding areas from 1961-2015,variations, trends and temporal-spatial distribution were analyzed, furthermore, the possible reasons were also discussed preliminarily. The main results are summarized as follows: the annual mean precipitation in the TP is 465.54mm during 1961-2015, among four seasons, the precipitation in summer accounts for 60.1% of the annual precipitation, the precipitation in summer half year (May.- Oct.) accounts for 91.0% while that in winter half year (Nov.- Apr.) only accounts for 9.0%; During 1961-2015, the annual precipitation variability is 0.45mm/a and the seasonal precipitation variability is 0.31mm/a, 0.13mm/a, -0.04mm/a and 0.04mm/a in spring, summer, autumn and winter respectively on the TP; The spatial distribution of precipitation can be summarized as decreasing from southeast to northwest in the TP, the trend of precipitation is decreasing with the increase of altitude, but the correlation is not significant. The rising of air temperature and land cover changes may cause the precipitation by changing the hydrologic cycle and energy budget, furthermore, different pattern of atmospheric circulation can also influence on precipitation variability in different regions.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Transition-metal-free synthesis of 4-pyrones via TfOH-promoted nucleophilic addition/cyclization of diynones and water has been developed. This transformation is simple, atom economical and environmentally benign, providing rapid and efficient access to substituted 4-pyrones.

The sustainability of agricultural commodities produced in the Southern U.S. under irrigation is increasingly at risk due to erratic rainfall patterns, inadequate water supplies and compromised water quality. This study assessed the needs of crop growers in the United States Department of Agriculture (USDA) Southern Region. The purpose was to identify growers’ critical water resource management concerns to identify research priorities from the perspective of growers in this region. To obtain this information, a questionnaire was developed and distributed to growers throughout the Southern Region in 2020. The final sample included 112 crop (row and specialty) production growers from the Southern Region. Overall, respondents named the water available to irrigate as the greatest water resource management priority. Within all the water availability priorities asked, respondents’ first choice was declining water supply in the future. Declining water supply and the cost of irrigating presently were the next most frequently named water availability priorities. Growers named both increasing the efficiency of irrigation and development of farming practices to improve soil moisture retention as the first and second focus of future irrigation research, respectively. These results will aid in strengthening existing and developing new initiatives for water research and Extension in this region.

This study investigates the concentrations of physicochemical and heavy metal contaminants in the groundwater of the Middle Awash Basin, Ethiopia, to inform targeted water management strategies. A total of 32 groundwater samples were collected from 16 stations via piezometers and boreholes at the end of both the dry (June 2021) and wet (October 2021) seasons. Utilizing Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Atomic Absorption Spectroscopy (AAS), and in situ metering, 22 physicochemical and 24 heavy metal parameters were analyzed. The data revealed significant levels of contamination; notably, sample GW11 had extraordinarily high concentrations of total dissolved solids (10,826 mg/L), strontium (908 µg/L), molybdenum (802.4 µg/L), zinc (6060 µg/L), and electrical conductivity (15,645 µS/cm), while GW12 exhibited elevated levels of aluminum (2615 µg/L), zinc (4446 µg/L), and arsenic (117.2 µg/L). Contaminants such as arsenic, vanadium, gallium, lithium, rubidium, chromium, manganese, copper, and zinc were found enriched in groundwater near Lake Beseka, influenced by agricultural runoff from sugarcane plantations and agro-industry activities. Over half of the groundwater sources were unsuitable for drinking, posing significant health risks to local communities that rely heavily on these sources due to limited access to clean surface water. The findings emphasize the urgent need for comprehensive groundwater management and remediation plans in the Middle Awash region to ensure safe and sustainable water use, particularly addressing the variation in contamination levels influenced by Lake Beseka. These measures are critical to protect public health and support local development in the face of ongoing environmental and anthropogenic pressures.

The growing global population and limitations in fish catch production have led to a surge in the demand for aquaculture. Contaminants of emerging concern (CEC) are frequently being detected at low levels in surface water. These CECs, which include previously unidentified or unregulated pollutants, pose potential risks to health and the environment, though their impacts are not yet fully understood. Extensive research studies have been proposed and undertaken to address the issue of aquaculture wastewater, aiming to minimize its impact and implement effective treatment methods. This review provides an analysis of various technologies used for treating aquaculture wastewater using advanced oxidation processes (AOPs) focusing on photocatalysis and ozonation. It examines their advantages and disadvantages, as well as their respective treatment efficacies and discusses their potential applications in sustainable aquaculture practices complying with the Sustainable Development Goals of 1,2 and 6 and the Environmental Social and Governance (ESG) framework.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P &lt; 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P &lt;0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

Lecanicillium lecanii KMZW-1, is recognized for its potential as a bio-control agent against agricultural and forestry pests, particularly due to its compatibility with integrated pest management (IPM) strategies. This study aimed to investigate the complete genome of L. lecanii KMZW-1 and assess its pathogenicity against Bactrocera dorsalis. Whole genome sequencing revealed a genome size of 47,239,278 bp, comprising 27 contigs, with a GC content of 51.16%. The genome completeness was assessed as 97.93% using BUSCO analysis, AntiSMASH analysis identified 29 gene clusters associated with secondary metabolite biosynthesis providing insights into the genetic basis of its pathogenic mechanisms and biocontrol potential. The pathogenicity of L. lecanii KMZW-1 was assessed using concentrations ranging from 1×10^4 to 1×10^11 spores/mL. Higher-concentrations (1×10^10 to 1×10^11 spores/mL), resulted in significantly increased cumulative mortality rates of B. dorsalis adults compared to the control group. Notably, the pathogenicity was higher in male adults than in females. Probit regression analysis yielded LogLC50 values as 5.662 for female and 4.486 for male B. dorsalis adults. In summary, L. lecanii KMZW-1 exhibits strong insecticidal activity against B. dorsalis and shows potential as a biocontrol agent with IPM strategies. These findings provide robust genomic evidence supporting the use of L. lecanii KMZW-1in managing against B. dorsalis populations.

Variable flow emitters are a new type of emitter for underground drip irrigation that are used in locations where soil moisture is difficult to transport to the surface, which leads to crop emer-gence difficulties. The flow channel structure parameters of emitters affect the hydraulic per-formance of the emitter and its anticlogging ability. In this study, the variable flow emitter at the conventional low–flow water supply stage is taken as the research object. A combination of CFD numerical simulation of a two–phase flow of water and sand and clear water testing of test samples is applied to study the influence laws of 10 groups of variable flow emitter structural combinations on the effluent flow rate (q), flow index (x), particle passage rate and flow field inside the flow channel. The results show that the Realizable k–ε turbulence model can be used to simulate the flow field inside the variable flow emitter flow channel. The nRMSE between the measured and simulated values of q is 11.23%, and the relative error between the measured and simulated values of x is 4.66%, which gives a high simulation accuracy. The polar analysis shows that the tooth angle A has the smallest effect on the effluent flow rate q0.1 under 0.1 MPa, x, and particle passage rate of the variable flow emitter. The depth of the flow channel D, the spacing of the teeth B, and the height of the teeth E have a different order of precedence in the influence of the three indices, which are D > B > E > A, B > E > D > A, and E > B > D > A, respectively. The value of particle passage rate is positively correlated with the mean flow velocity (v) and the mean turbulent kinetic energy (k) in the flow channel, and particle passage rate tends to increase and then decrease with the increase of x. The retention time (t) of the particles in the flow channel is closely related to the magnitude of v and k. Three multivariate linear regression equations (R2 = 0.883 ~ 0.995) were constructed for q0.1, x, and particle passage rate versus the flow channel structural parameters. Using the scipy.optimize.minimize function in Python, we de-termined the three optimal combinations of flow channel structural parameters corresponding to better hydraulic performance: q0.1 is 1.5 or 2 L/h (objective function y = min x), better clogging resistance (y = max particle passage rate), and both (y = min (0.5 x - 0.5 particle passage rate)). The research results can provide a ref-erence for the optimal design of variable flow emitters.

The global steel industry is a major contributor to greenhouse gas emissions, and the adoption of green hydrogen in Direct Reduced Iron (DRI) production has the potential to significantly reduce CO2 emissions and support climate targets. This review explores the environmental, economic, technological, and social implications of using green hydrogen in DRI processes. The findings suggest that green hydrogen can reduce emissions by up to 90% compared to traditional methods, enhance energy security, and stimulate local economic development. However, high initial costs, energy efficiency concerns, and social acceptance issues remain significant barriers. The review also highlights the importance of integrating carbon capture and storage technologies, addressing logistical challenges, and considering the geopolitical implications of a shift towards green hydrogen. Green hydrogen presents a promising solution for decarbonising the steel industry but continued research, investment in infrastructure, and strategic planning are essential to overcome the challenges and drive widespread adoption.

The North China Plain is among the regions most afflicted by ground fissure disasters in China. Recent urbanization has accelerated ground fissure activity in the three counties of the northern North China Plain, posing significant threats to both the natural environment and socioeconomic sustainability. Despite the increased attention, a lack of comprehensive understanding persists due to delayed recognition and limited research. This study conducted field visits and geological surveys across 43 villages and 80 sites to elucidate the spatial distribution patterns of ground fissures in the aforementioned counties. By integrating these findings with regional geological data, we formulated a causative model to explain ground fissure formation. Our analysis reveals a concentration of ground fissures near the Niuxi and Rongxi faults, with the former exhibiting the most extensive distribution. The primary manifestations of ground fissures include linear cracks and patch-shaped collapse pits, predominantly oriented in east-west and north-south directions, indicating tensile failure with minimal vertical displacement. Various factors contribute to ground fissure development, including fault activity, ancient river channel distribution, bedrock undulations, rainfall, and ground settlement. Fault activity establishes a concealed fracture system in shallow geotechnical layers, laying the groundwork for ground fissure formation. Additionally, the distribution of ancient river channels and bedrock undulations modifies regional stress fields, further facilitating ground fissure emergence. Rainfall and differential ground settlement serve as triggering mechanisms, exposing ground fissures at the surface. This research offers novel insights into the causative mechanisms of ground fissures in the northern North China Plain, providing valuable scientific evidence for mitigating ground fissure disasters during the urbanization process in the region.

Carbon (C) losses due to the conversion of natural forests adversely affect the abiotic components of terrestrial ecosystems. In tropical China, rubber cultivation often extends from its traditional range to elevations of up to 1400 m. However, C storage in rubber plantations across elevation gradients is poorly understood. In this study, we investigated biomass and C storage along elevation gradients in two age groups (8- and 12-year-old) of rubber monoculture plantations in Xishuangbanna, Southwest China. We investigated the C distribution across various tree sections, ranging from aboveground biomass (AGB) to belowground biomass (BGB), including litter, big dead branches, and different soil depths. A significant negative correlation was observed between total ecosystem C stocks and elevation in both age groups of rubber plantations. The highest ecosystem C stock of 197.90 Mg C ha–1 was recorded at 900 m in 8-year-old plantations, whereas in 12-year-old rubber plantations, the highest value of 183.12 Mg C ha–1 was found at 700 m. The total ecosystem C stocks decreased to its lowest level at 1000 m in both the 8-year-old and 12-year-old plantations, ranging between 113.05 Mg C ha–1 and 125.75 Mg C ha–1, respectively. We concluded that the total ecosystem C stocks were negatively correlated with elevation and significantly decreased from 8.05% to 51.55% and 11.46% to 42.96% between 700 m and 1100 m in both 8-year-old and 12-year-old plantations, respectively. However, no correlation was observed between the total soil C stocks and elevation in either age group of rubber plantations. Regardless of elevation gradient, the total ecosystem C stock of 12-year-old rubber plantations was 1.98% greater than that of 8-year-old rubber plantations. Biomass was the second largest contributor, while soil accounted for 82% to 90%, and the other factors contributed less than 2% of the total ecosystem C stock in both age groups. These fluctuations in C stocks along elevation gradients in both 8- and 12-year-old plantations suggested that rubber growth, biomass and C storage capacity decreased above 900 m and that age and elevation are key factors for biomass and C storage in monoculture rubber plantations.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

The isotopic and nuclear techniques discussed, namely: Fallout Radionuclide, Fingerprint, and Isotope Hydrology, are linked to the evaluation of soil and water degradation processes. A traditional literature review was conducted to gain the most comprehensive understanding of both the current state of the art and the subject matter, with the aim of proposing a hypothesis that integrates the synergistic convergence of these techniques in order to offer results that are more reliable. A case study is presented as a synthesis of the preceding discussion.

The Lower Mekong Basin has had extensive hydropower dam development, which changes hydrologic conditions and threatens the exceptional aquatic biodiver-sity. This study quantifies the degree of hydrologic change between pre-impact (1965-1968) and post-impact (2018-2021) peak hydropower development in two major tributaries of the Lower Mekong Basin, the Sekong River with the fewest dams and the Sesan River with the most dams. Both rivers historically supported migratory fishes. We use daily pre- and post-impact data and the Indicators of Hydrologic Alteration framework to evaluate streamflow changes from dam development. We found signifi-cant changes in low and high magnitude flows in the pre- and post-impact periods of dam development. For the Sekong River, minimum flow had large fluctuations that ranged 290% to 412% more than the pre-impact period, while the Sesan River ranged 120% to 160% more than pre-impact. Dry season flows increased by 200±63% on av-erage in the Sekong River, which is caused by releases from upstream dams. Mean-while, Sesan River dry season flows increased by 100±55% on average. This study in-dicates that seasonal flow changes and extreme flow events occurred more frequently in the two basins following dam construction, which may threaten the ecosystem func-tions.

The cassava whitefly, Bemisia tabaci, causes direct damage to cassava in the tropics by feeding on the phloem of leaves, inducing leaf chlorosis and abscission which can result in considerable yield loss of up to about 50% on susceptible varieties. The pest is also known to impart its indirect damage through sooty mold formation. Most of the improved cassava varieties in Uganda were developed for CMD resistance and CBSD tolerance and little is known about their reaction to whitefly infestation. A study was conducted to evaluate the reaction of 24 improved cassava varieties which were sourced from 5 different countries in the region (Uganda, Kenya, Tanzania, Malawi, and Mozambique) to whitefly infestation. These varieties were evaluated in three agro-ecological zones of Uganda, namely; North-Western Savannah Grassland, Lake Victoria Crescent and the Kyoga Plains in the second rains of 2016. Monthly data were taken on adult and nymph counts, whitefly and sooty mold damage, CMD and CBSD severities from 2 up-to 9 Months after planting (MAP). Results show that the whitefly population was highly significantly (P

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

Monitoring the status and dynamics of desertification is one of the most important parts of combating desertification. In this study, 30m high-resolution information on land desertification and restoration in the HRB was extracted from the land cover database. The results indicate that land desertification coexists with land restoration in the HRB. At different periods, the area of land restoration is much larger than the area of land desertification in the HRB, and the HRB has been in a process of land restoration. Upstream of the HRB, there is a continuing trend of increasing land desertification associated with overgrazing in a context where climate change favors desertification reversal. In the middle and lower reaches, although both climate variability and human activities favor land desertification, the process of land desertification in the middle and lower reaches is still being reversed and land restoration dominates. The implementation of the Eco-Environmental Protection Project and desertification control measures, especially the EWDP, is contributing to the reversal of desertification in the middle and lower reaches of the HRB. However, the EWDP has indirectly led to the lowering of the water table in the middle reaches, resulting in local vegetation degradation. Therefore, there is therefore an urgent need to transform the economic structure of the middle reaches to cope with water scarcity and land desertification.

Climate change is a global issue that draws widespread attention from the international society. As an important component of the climate system, the water cycle is directly affected by climate change. Thus, it is very important to study the influences of climate change on the basin water cycle with respect to maintenance of healthy rivers, sustainable use of water resources, and sustainable socioeconomic development in the basin. In this study, by assessing the suitability of multiple General Circulation Models (GCMs) recommended by the Intergovernmental Panel on Climate Change, Statistical Downscaling Model (SDSM) and Automated Statistical Downscaling model (ASD) were used to generate future climate change scenarios. These were then used to drive distributed hydrologic models (Variable Infiltration Capacity, Soil and Water Assessment Tool) for hydrological simulation of the Yangtze River and Yellow River basins, thereby quantifying the effects of climate change on the basin water cycle. The results showed that suitability assessment adopted in this study could effectively reduce the uncertainty of GCMs, and that statistical downscaling was able to greatly improve precipitation and temperature outputs in global climate mode. Compared to a baseline period (1961–1990), projected future periods (2046–2065 and 2081–2100) had a slightly decreasing tendency of runoff in the lower reaches of the Yangtze River basin. In particular, a significant increase in runoff was observed during flood seasons in the southeast part. However, runoff of the upper Yellow River basin decreased continuously. The results provide a reference for studying climate change in major river basins of China.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

In an effectively managed grazing system, goats as grazers can benefit the land's physical, chemical, biological, and economic aspects. However, little research has evaluated rotational and continuous goat grazing in Kentucky. This observational study investigated the impact of rotational and continuous grazing on forage production and goat performance. One group of 10 does was placed on a rotational pasture, and another group of 10 does were placed on a continuous pasture, each pasture measuring two acres. The pastures were side-by-side with similar forage types and compositions. Goat performance was measured by body weight and eye color score (FAMCHA). Forage production was measured weekly by collecting forage heights at three random spots in each pasture. The rotational grazing field displayed a more evenly grazing pattern, while the continuous field experienced overgrazing in some areas and overgrown of the less desired forage. Goats on the continuous field had a decrease in body weight, while the weights were more consistent in the rotational grazing field. The FAMACHA score was temporarily reduced on the rotational grazing pasture, indicating that properly managed rotational grazing may prevent anemia, possibly by reducing the shedding of gastrointestinal parasites. However, due to drought and lack of forage, the FAMACHA score of goats in the rotational grazing system reverted to its original status by the end, indicating that more extensive management and timely adjustments are necessary to ensure optimal goat performance. Our results suggest that rotational grazing may support more consistent forage yields and body weights of goats and has the potential to reduce the incidence of anemia and parasitic infestations in goats in Kentucky.

Climate change, growing world population and increasing food demand require higher yields and adaptability of crops, including spring bread wheat. Modern plant breeding based on achievements of genetics has a significant impact on plant resistance to diseases, climate variability and other factors. Genome wide association studies (GWAS) is one of genetics tools for mining of genome loci associated with economically important traits. In the current study, we applied GWAS to reveal QTL for spike productivity and grain quality using a panel of spring varieties of Triticum aestivum L. bred in different decades of the last century in Russia and Germany. The study has enabled to find new genetic markers associated with grain yield and quality. Studying genetic basis of grain yield and quality by comparison of wheat varieties from different breeding periods, including landraces preserved as the source of valuable genetic diversity for breeding and genetic studies, makes it possible not only to understand selection processes in the past, but also to develop strategies for future breeding work.

This study examines the Soil Organic Carbon (SOC) within Greek croplands, offering a comprehensive understanding of its dynamics. SOC, a cornerstone in soil health, nutrient cycling, and global carbon dynamics, assumes critical significance in sustainable agriculture and climate change mitigation. Drawing on diverse soil properties, including pH, soil texture as well as different drainage and slope categories, the research explores the nuanced relationships shaping SOC dynamics in the diverse agroecological landscape of Greece. The investigation transcends local boundaries, emphasizing SOC's global role in climate change mitigation by sequestering carbon dioxide. Two maps were used as data sources: 1) SOC stock baseline map (2010) by JRC, 2) SOC stock map (2021) by the Institute of Soil and Water Resources, Hellenic Agricultural Organization – DIMITRA in collaboration with FAO. Greek croplands emerge as a mosaic of agroecological diversity, where anthropogenic activities wield transformative influences on SOC stock, demanding a delicate balance between agricultural productivity and soil health. The study unveils the influence of Soil Order, weaving a tapestry of SOC variability. Microscopic factors, from soil texture to cation exchange capacity, further shape SOC dynamics, emphasizing the role of clayey soils and coarse materials in carbon retention. Although soil organic carbon decreased from 2010 to 2021 the degree of carbon loss varied. This scientific endeavor synthesizes existing knowledge and unveils novel insights, offering a narrative woven from diverse soil properties. The findings contribute valuable insights for sustainable land management practices and climate change mitigation strategies, underscoring the importance of region-specific approaches in addressing global challenges.