This study aimed to evaluate the relationship between various asbestos exposure routes and asbestos-related disorders (ARDs). The study population comprised 11,186 residents of a metropolitan city who lived near asbestos factories, shipyards, or in slate roof-dense areas. ARDs were defined from chest X-rays indicating lower lung fibrosis (LFF), pleural disease (PD), and lung masses (LMs). Of the subjects, 11.2%, 10.4%, 67.2% and 8.3% were exposed to asbestos via occupational, household, neighborhood, and slate roof routes, respectively. Regarding adjusted confounders and other exposure routes, the odds ratio (OR) of PD from household exposure (i.e., living with asbestos-producing workers) was 1.9 (95% confidence interval: 0.9–4.2), and that of LLF and PD from neighborhood exposure, or residing near asbestos factories) for <19 or >20 years, or near a mine, were 4.1 (2.8–5.8) and 4.8 (3.4–6.7), 8.3 (5.5–12.3) and 8.0 (5.5–11.6), and 4.8 (2.7–8.5) and 9.0 (5.6–14.4), respectively. The ORs of LLF, PD, and LM among those residing in slate-dense areas were 5.5 (3.3–9.0), 8.8 (5.6–13.8), and 20.5 (10.4–40.4), respectively. Substantial proportions of citizens residing in industrialized city have potentially been exposed to asbestos, and various exposure routes are associated with the development of ARDs. Notably, this may be the first finding of the health effects of slate roof exposure. However, given the limitations of this study, including potential confounders such as socioeconomic status, further research is needed.

Outdoor lighting is becoming increasingly widespread, and residents are suffering from serious light pollution as a result. Residents’ awareness of their rights to protection has gradually increased. However, due to the sometimes-inaccessible nature of residential vertical light incidence intensity data and the high cost of obtaining specific measurements, there is no appropriate hierarchic compensation for residents suffering from different degrees of light pollution. It is therefore important to measure light pollution levels and their damage at the neighborhood scale to provide residents with basic materials for proper protection and to create more politically suitable solutions. This article presents a light pollution assessment method that is easy to perform, is low-cost, and has a short data-processing cycle. This method can be used to monitor residential zone light pollution in other cities. We chose three open areas to test the spatial variation pattern of light intensity. The results are in accordance with spatial interpolation patterns and can be fit, with high precision, using the IDW method. This approach can also be used in 3 dimensions to quantitatively evaluate the distribution of light intensity distribution. We use a mixed-use zone in Beijing known as The Place as our case study area. The vertical illumination at the windows of residential buildings ranges from 2 lux to 23 lux; the illumination in some areas is far higher than the value recommended by CIE. Such severe light pollution can seriously interfere with people's daily lives and has a serious influence on their rest and health. The results of this survey will serve as an important database to assess whether the planning of night-time lighting is scientific and whether it provides residents with a basis for the protection of their rights.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

High maternal mortality in the developing countries, particularly in Nigeria, poses serious challenge to achieving the maternal mortality target of the Sustainable Development Goals (SDGs) in the countries. Hence, there is need for multifaceted approach to curtailing the scourge. Women being the victims of maternal mortality, this study finds the effect of their household decision making power in reducing maternal mortality. The study used data from the 2013 Nigeria Health and Demographic Survey (NDHS) and logistic regression model to explore the relationship between women household decision making power and maternal mortality in Nigeria. The finding shows that women who decide and participate in household decision on own health, major purchases and visit to family and relatives were 35% (OR = 0.65, 95% CI: 0.52, 0.83), 27% (OR = 0.73, 95% CI: 0.57, 0.92), and 37% (OR = 0.63, 95% CI: 0.50, 0.80) less likely to experience maternal mortality, respectively, compared to those whose husbands alone decide. Women household decision making power is therefore instrumental to reducing maternal mortality. It is thus important for policy makers, particularly in Nigeria, to pay more attention to social and cultural factors that surround women household decision making ability for speedy reduction in maternal deaths.

Given the importance of the development of urban infrastructure and environmental impacts produced by the civil construction waste (CCW), it is important to correct the handling of CCW with objective solutions that are more environmentally friendly. In that sense the present study aimed to determine indicators that make it possible to estimate the amount of CCW generated from construction sites in the city of Londrina, Parana State, Brazil. The generation of CCW was estimated in a general way, regarding the composition of its mixture, correlated to the gross areas of the buildings studied and their generated volumes of RCC. This generating rate was evaluated in a general way and specifies two types of sites: the new residential and new non-residential constructions. The data required for the development of these indicators was obtained through extensive survey and interviews carried out at the environment secretariat of the City Hall. The generating rate of CCW obtained for non-residential buildings was 0.2052m3/m2 or 170.44kg/m2, for new residential sites was 0.2054m3/m2 or 170.60kg/m2 and for new commercial or non-residential construction sites, it was 0.20453 m3/m2 or 169.85kg/m2. It was also possible to estimate the amount generated annually per inhabitant in the municipality, which is 0.60m3/inhabit.year or 498.55kg/inhabit.year.

Due to the incomplete of China's current social security system, health shocks are one of the main risks faced by rural families. Using data from the 2019 China Household Finance Survey, we examined the impact of borrowing on household welfare when rural households face health shocks. We found that household income and food expenditure both declined significantly when rural households faced health shocks; rural household borrowing was mainly used for the treatment of the diseases, and it had a crowding out effect on tourism and general health care expenditures, but not on education expenditures. We also found that the impact of borrowing on the western region was higher than that on the central and eastern regions from Looking at the impact of borrowing in different regions. Finally, we put forward some suggestions for promoting sustainable rural development from the perspective of medical security, such as accelerating the promotion of new rural medical insurance, helping rural low-income families improve health benefits, establishing diversified financing channels, improving rural financial platforms, and solving the financing difficulties of households to improve the ability of rural households to resist health shocks.

Residential dust is recognized as a major source of environmental contaminants, including polycyclic aromatic hydrocarbons (PAHs) and phthalic acid esters (PAEs). To characterize the thoracic dust fraction (PM10), a sampling campaign was carried out with an in-situ resuspension chamber in three rooms (kitchen, living room and bedroom) of four Spanish houses. Two samples per room were collected with, at least, a one-week interval. The PM₁₀ samples were analyzed for their carbonaceous content by a thermo-optical technique and, after solvent extraction, for 20 PAHs, 8 phthalate plasticizers (PAEs) and one non-phthalate plasticizer (DEHA) by gas chromatography-mass spectrometry. In general, higher dust loads were observed for parquet flooring compared with tile. The highest dust loads were obtained for rugs. Total carbon accounted for 9.3 to 51%wt of the PM₁₀ mass. Plasticizer mass fractions varied from 5 µg g-1 to 17 mg g^-1 PM₁₀, whereas lower contributions were registered for PAHs (0.98–116 µg g^-1). The plasticizer and PAH daily intakes for children and adults via dust ingestion were estimated to be 3–4 orders of magnitude higher than those via inhalation and dermal contact. Potential carcinogenic and negligible non-carcinogenic risks arising from exposure to PAHs were found.

This study aims to determine the impact of the type of ICT usage on household income from main vegetables, agriculture (including main vegetables), and total income. This study is based on surveys and interviews with vegetable farmers using structured questionnaires conducted in three villages in Indonesia, including Cianjur, Sleman, and Malang in West Java, Yogyakarta, and East Java, respectively. The data were collected from 375 respondents selected in each region from November 2021 to March 2022. An econometric model called the multivariate linear regression (MLR) model is used to assess heterogeneous factors that influence the possibility of increasing the income of vegetable farmers. The study found that variables that use ICT as a primary variable, household, marketing, geographical characteristics, and immediate source information in agriculture have a significant impact on household income (P < 0.01) from primary vegetables, agriculture, and total income, with multiple R squares of 70.5, 72.0, 73.7% and F statistics of 28.48, 30.66, and 33.34, respectively. In summary, this novel study shows that the five categories of information technology used in farming and selling of harvest have a positive impact on household incomes

Effective household and individual disaster preparedness can minimize physical harm and property damage during catastrophic events. To assess the risk and vulnerability of affected areas, it is crucial for relief agencies to understand the level of public preparedness. Traditionally, government agencies have employed nationwide random telephone surveys to gauge the public’s attitudes and actions towards disaster preparedness. However, these surveys may lack generalizability in certain affected locations due to low response rates or areas not covered by the survey. To address this issue and enhance the comprehensiveness of disaster preparedness assessments, we develop a framework that seamlessly integrates machine learning and simulation. Our approach leverages machine learning algorithms to establish relationships between public attitudes towards disaster preparedness and demographic characteristics. Using Monte Carlo simulation, we generate datasets that incorporate demographic information of the affected location based on government-provided demographic distribution data. The generated dataset is then input into the machine learning model to predict the disaster preparedness attitudes of the affected population. We demonstrate the effectiveness of our framework by applying it to Miami-Dade County, where it accurately predicts the level of disaster preparedness. With this innovative approach, relief agencies can have a clearer and more comprehensive understanding of public disaster preparedness.

This work aims to investigate the effect of process temperature and catalyst content by thermochemical degradation of municipal solid waste (MSW) fraction (organic matter + paper + plastic) on the yield of reaction products (bio-oil, biochar, H2O and gas), physicochemical properties and chemical composition of bio-oils, as well as on the morphology and crystalline phases of biochar in laboratory scale. The organic matter, paper and plastic segregated from the gravimetric composition of total waste sample were subjected to the pre-treatments of drying, crushing and sieving. The experiments were carried out at 400, 450 and 475 °C and 1.0 atmosphere, and at 450 °C and 1.0 at-mosphere, using 5.0, 10.0 and 15.0% (wt.) of FCC zeolite, bath mode, using a laborato-ry scale glass reactor. The bio-oil was characterized for acidic value. The chemical functions present in the bio-oil identified by FT-IR and the composition by GC-MS. Biochar was characterized by SEM/EDS and XRD. Thermal pyrolysis of the MSW frac-tion (organic matter + paper + plastic) shows bio-oil yields between 9.44 and 9.24% (wt.), aqueous phase yields between 21.93 and 18.78% (wt.), solid phase yields between 67.97 and 40.34% (wt.) and gas yields between 28.27 and 5.92% (wt.). The yield of bio-oil decreases with increasing process temperature. For the experiments using FCC, the biochar and gas yields increase slightly with the FCC content, while that of bio-oil de-creases and the H2O phase remains constant. The GC-MS of bio-oils identified the presence of hydrocarbons and oxygenates, as well as nitrogen-containing compounds, including amides and amines. The acidity of the bio-oil increased with increasing temperature and with the aid of FCC as a catalyst. It has been identified the presence of hydrocarbons within bio-oil by addition of FCC catalyst due to the deoxygenation of carboxylic acids, followed by decarboxylation and decarbonylation reactions, producing aliphatic and aromatic hy-drocarbons.

Drought is a long period of unusually low rainfall and can have serious effects on people's lives. It is caused by various factors such as climate change, deforestation, and the overuse of water re-sources. In the Somali region of Ethiopia, Kebri Dehar is the most at risk and most likely to have a drought. The lack of rainfall and high temperatures in Kebri Dehar have led to drought. Man-aging drought is the most challenging and complex problem. The purpose of this study is to as-sess household perception of drought hazards occurrence and adaptation. Additionally, the study aims to design a drought resilience mechanism matrix to mitigate its impact on the local commu-nity. This study used the Heckman two-stage model, which is useful in measuring drought per-ception as it accounts for potential selection bias and allows for the identification of factors that influence individuals' perceptions of drought. Gender, severity of drought, water shortage, tem-perature, drought frequency, and long dry season all have a positive effect on adaptation of resil-ience mechanisms to drought hazards, while food availability and rainfall have a negative effect. It is important for governments and individuals to act to mitigate the effects of the drought. Ef-forts to address the issue require a multi-participation approach that involves household, com-munity, and institutional level participation is needed for adopting drought resilience mecha-nisms.

Rice is the most important food crop in Cambodia and its production is the most organized food production system in the country. The main objective of this study is to measure technical efficiency (TE) of Cambodian rice production and also trying to identify core influencing factors of rice TE at both national and household level, for explaining the possibilities of increasing productivity and profitability of rice, by using translog production function through Stochastic Frontier Analysis (SFA) model. Four-years dataset (2012-2015) generated from the government documents was utilized for the national analysis, while at household-level, the primary three-years data (2013-2015) collected from 301 rice farmers in three selected districts of Battambang province by structured questionnaires was applied. The results indicate that level of rice output varied according to the different level of capital investment in agricultural machineries, total actual harvested area, and technically fertilizers application within provinces, while level of household rice output varied according to the differences in efficiency of production processes, techniques, total annual harvested land, and technically application of fertilizers and pesticides of farmers. The overall mean TE was estimated at 78.4% (national-level) and 34% (household-level), indicates that rice output has the potential of being increased further by 21.6% (national production) and 66% (household) at the same level of inputs and technology if farmers had been technically efficient. The TE also recorded -7% decreasing rate at the national-level and -14.3% at household-level due to highly affected of natural disasters and various environmental and social factors during the study periods.

Trade liberalization is commonly pursued to improve welfare of households in a country. However, the effects of liberalization are not evenly distributed. Certain households and sectors may benefit more than others. This study focuses on the East African Community Common External Tariff (EAC-CET), to analyze the distributional effects of trade liberalization in Kenya. The study utilizes two household budget surveys capturing pre- and post-trade liberalization scenarios. The paper examines changes in consumer prices, labor incomes, and consumption patterns to assess the effects of liberalization. A pass-through equation for prices and a negative compensation variation equation are estimated. The findings indicate that the EAC-CET had a significant pass-through effect on prices of manufactured goods, but incomplete pass-through for agricultural goods. This suggests a lack of competitiveness in domestic value chains. The distributional effects differ across worker categories, favoring skilled and formal workers over unskilled and informal workers. The income effect outweighs the negative expenditure effect for households in the middle- and upper-income deciles. However, the study reveals negative welfare effects for the poorest households in the lowest income deciles. Furthermore, the study identifies the EAC-CET to be pro-poor, with households in rural areas benefiting more than those in urban areas.

Bacteria that have become resistant to antibiotics, also known as superbugs,pose a huge threat to the human population. This is because these developed resistance to antibiotics. Antibiotics are a type of medicine that fights bacteria by either killing it or preventing it from growing. Although antibiotics make the once deadly now easily treatable, they can become ineffective as bacteria develop resistance to the antibiotic, causing diseases to become potentially fatal once more. Thus, scientists are rushing to find solutions in this arms race against evolving bacteria by either evolving current antibiotics or discovering new stands to fight evolving bacteria. In order to discover whether bacteria can develop resistance to household antibiotics, a controlled experiment was conducted. This was done by growing bacteria on agar plates with antibiotic ointments applied (in dilution series) to see if antibiotic resistance could build. Theorizing that by lowering the concentration of over the counter antibiotics, resistant bacteria would be selected and my bacterial population would evolve antibiotic resistance.In conclusion of the experiment antibiotic resistance did appear as a trait, but the level of it was inconsistent across the different bacteria populations.

Computer vision methods have shown to be effective in classifying garbage into recycling categories for waste processing, existing methods are costly, imprecise, and unclear. To tackle this issue, we introduce MWaste, a mobile application that uses computer vision and deep learning techniques to classify waste materials as trash, plastic, paper, metal, glass or cardboard. Its effectiveness was tested on various neural network architectures and real world images, achieving an average precision of 92% on the test set. This app can help combat climate change by enabling efficient waste processing and reducing the generation of greenhouse gases caused by incorrect waste disposal.

The rate of fires, and particularly residential-fires, is a serious concern in industrialized countries. However, there is considerable uncertainty regarding the reported numbers of residential-fire incidents as official figures are based on fires reported to fire response agencies only. This population-based study aims to quantify the total number of residential-fire incidents regardless of reporting status. The cohort comprised linked person-level data from Fire and Rescue New South Wales (FRNSW) and health system and death records. It includes all persons residing at a residential address in New South Wales, Australia, that experienced a fire between 1 January 2005 – 31 December 2014. Capture-Recapture method was used to estimate the underreporting number of residential fire-related incidents. Over the study period, 43,707 residential-fire incidents were reported to FRNSW and there were 2,795 residential fire-related health service utilization of which 2,380 were not reported. Using Capture-Recapture method, the total number of residential-fire incidents was estimated at 267,815 to 319,719 which is more than six times the official records. This study found that 15% of residential-fire incidents that were identified in health administrative dataset were reported. The residential-fire incidents that were not reported occurred mainly in socio-economically disadvantaged areas among the males and adults.

According to a recent estimate by UN Habitat, approximately 3 billion individuals will require suitable housing by the year 2030. This staggering demand translates to the need for around 96,000 affordable housing units to be constructed each day. However, the conventional construction methods that rely on cement-based concrete and masonry are outdated, lacking innovation, efficiency, and sustainability. In light of these challenges, cold-formed steel emerges as an appealing alternative to traditional construction materials like masonry and concrete. It offers numerous advantages, including easy fabrication, lightweight properties, energy efficiency, the ability to reuse the material at the end of its service life, and a higher level of recyclability. Cold-formed steel buildings are also recognized for their superior insulation and lower energy consumption during operation. Cold-formed steel (CFS) members are created by rolling structurally sound steel sheets into the required shapes using a forming machine, without the need for heat as in the case of hot-rolled steel. While the thickness of these members can range from 0.01 mm to 7 mm, commercial construction of load-bearing walls, roof trusses, and floor joists typically utilizes steel thicknesses of 0.7 mm to 1.2 mm. This paper tries to illustrate the materials and methods employed in the construction of cold-formed steel modular buildings in Sri Lanka[1]. It delves into the material and durability characteristics of cold-formed steel, the design philosophy behind these structures, the development of the building envelope, and the energy efficiency features of the building elements. The findings of this study demonstrate that cold-formed steel buildings can be a highly sought-after alternative for residential construction, offering faster construction timelines, cost-effectiveness, and energy-efficient practices.

The present study measured household hunger in South-East Nigeria amidst COVID-19 lockdown. A total of 1209 households (urban and rural locations) were sampled. Household hunger was determined using Radimer/Cornel hunger scale, while Chi-square test was done with significance of P<0.05. Results of this study revealed 82.7% prevalence of hunger among households before Covid-19 pandemic, while during Covid-19 lockdown, hunger prevalence rose to 98.6%. It was also observed that covid-19 lockdown significantly affected food prices.The major coping strategy employed by households was relying on less expensive foods(81.14%). A genuine fear of household hunger amidst Covid-19 lockdown in south-East Nigeria was confirmed.

Nowadays Air-Source Heat Pumps (ASHP) in combination with a Photovoltaic (PV) installation are a very promising option for a necessary and urgent energy transformation in European Union (EU). It is extremely important to develop solutions that will help maximize the use of energy generated from renewable energy sources (RES). Such issues include the problem of insufficient use of generated electricity in PV on-grid microinstallations in residential buildings. This paper's aim is to analyze the results of one-year-round operation of a PV array grid-connected hybrid installation with ASHP for domestic hot water (DHW) preparation in a residential building in Cracow, Poland in the context of increasing self-consumption (SC) of PV energy. Models of systems are built and simulated in Transient System Simulation Tool 18 (TRNSYS) software. Simulations were carried out for different scenarios involving different building electricity consumption profiles, PV system capacity and specified runtime management of ASHP. The novelty of this study lies in the evaluation of the impact of a certain range of conditions on the energy performance of the system, in particular on SC. The results showed that the use of ASHP, with specified runtime management, results in an increase in monthly SC values from 7 to 18%, and annual SC values up to 13%. Also determining the appropriate size of the used PV system depending on whether it is present ASHP in the installation is crucial to increase the value of the SC parameter. Overall, this study provides valuable insights into the potential benefits of PV panels and ASHP operating together, in particular on SC values.

As fossil-fueled heating in the building sector is responsible for 16 % of Germanys total CO2 emissions, it is of great importance to use climate-neutral alternatives for the decarbonization of this sector. Options for the climate-neutral heating of buildings include electricity or hydrogen as energy carriers, both explicitly considered by German policy. In this paper, bottom-up studies are conducted to investigate the role of hydrogen for the climate-neutral energy supply of ten selected residential buildings in comparison to electricity-based systems. Based on a selection of as different typical buildings as possible for single- (SFH) and multi-family houses (MFH) of different construction years, demand profiles are simulated for each building and the respective cost-optimal supply system is determined. For the construction of this system, the electricity-based technologies available are electric heater and heat pump as well as the hydrogen-based technologies hydrogen boiler and fuel cell combined heat and power (CHP) system. Based on the results of the optimization, sensitivity analyses are performed. These analyses aim to identify threshold values of the hydrogen price for the use of hydrogen in building energy systems as well as to make the quantities of hydrogen consumed visible.The identified threshold values show the significant role of hydrogen-operated CHP in MFH if the hydrogen price reaches 0.17 €/kWh_H2 in 2050 at an electricity price of 0.31 €/kWh_el. So, hydrogen-based energy systems represent an economically viable alternative to electricity-based systems with heat pumps. We identify electricity to hydrogen price ratios for the economically viable use of hydrogen in the examined buildings that range from 1.67 to 2.82. According to these ratios, the economically reasonable use of hydrogen in buildings can be derived. For the individual building groups for the year 2050, a ratio of 2.5 can be determined for SFH and 1.8 for MFH, that is favored by the use of CHP which also supplies electricity to the buildings. However, the role hydrogen will finally play in German residential buildings in the future depends to a large extent on political decisions on distribution issues and price signals.

Spending on out-patient health care by citizens in limited resource countries has received little attention.The purpose of this study is to determine the predictors of household spending on out-patient expenses in a cross-sectional study in Kenya. We applied the GEE methods to determine the effect of various variables on outpatient care. We established that the best predictors for outpatient spending in Kenya are Age of the household head, wealth index, marital status and education, which had the lowest QICu of 976341.2. There were no differences on age in mean spending on outpatient care and was changing in a sinusoidal manner. The rich spend more on outpatient care, due to financial ability. Spending increased across the wealth quantiles while gender had a significant effect in the general performance of the models, it didn’t assist in lowering the QICu

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

Whether evaluating gridded population dataset estimates (e.g. WorldPop, LandScan) or household survey sample designs, a population census linked to residential locations are needed. Geolocated census microdata data, however, are almost never available and are thus best simulated. In this paper, we simulate a close-to-reality population of individuals nested in households geolocated to realistic building locations. Using the R simPop package and ArcGIS, multiple realizations of a geolocated synthetic population are derived from the Namibia 2011 census 20% microdata sample, Namibia census enumeration area boundaries, Namibia 2013 Demographic and Health Survey (DHS), and dozens of publicly available spatial datasets. Realistic household latitude-longitude coordinates are manually generated based on public satellite imagery. Simulated households are linked to latitude-longitude coordinates by identifying distinct household types with multivariate kmeans analysis, and modelling a probability surface for each household type using Random Forest machine learning methods. We simulate five realizations of a synthetic population in Namibia's Oshikoto region, including demographic, socioeconomic and outcome characteristics at the level of household, woman, and child. Comparison of variables in the synthetic population were made with 2011 census 20% sample and 2013 DHS data by primary sampling unit/enumeration area. We found that synthetic population variable distributions matched observed observations and followed expected spatial patterns. We outline a novel process to simulate a close-to-reality microdata census geolocated to realistic building locations in a low- or middle-income country setting to support spatial demographic research and survey methodological development while avoiding disclosure risk of individuals.

The global population is at risk of vitamin D deficiency due to low exposure to sunlight and low intake of the vitamin through diet. The aim was to investigate in women the association between vitamin D status and parathyroid hormone (PTH), ultraviolet radiation, lifestyle, ethnicity, social conditions, and residential greenness. A 1-year longitudinal study assessed vitamin D status in 309 women, latitude 51° 14' N. Blood samples were taken four times throughout the year for analysis of 25(OH)D and serum PTH concentration. After each seasonal visit, the individuals completed 4-day diet diaries and used two dosimeter badges for 1 week to estimate weekly UVR exposure. A questionnaire was applied to provide information about lifestyle and their ethnicity. Residential greenness was measured by Normalized Difference Vegetation Index (NDVI), within a 1000 m radius around each participant’s home address. Women living in greener spaces were more likely to have improved vitamin D status (RR: 1.51; 95%CI: 1.13 – 2.02), as well as those who were more exposed to UVR (RR: 2.05; 95%CI: 1.44 – 2.92). Our results provided a first insight into the connection between vitamin D, residential greenness, and lifestyle in a region of temperate climate and with a high degree of urbanization.

For the majority of the contractual arrangements used in construction projects, the owner is not responsible for the cost deviations due to the variability of labor productivity or material price, amongst many other aspects. Consequently, the cost performance of a project may be entirely distinct for the owner and the contractor. Since the majority of the quantitative research on cost estimation and deviation found in the literature adopts the owners’ perspective, this research provides a contribution towards modelling costs and cost deviation from a contractors’ perspective. From an initial sample of 13 residential building and 10 office building projects, it was possible to develop models for cost estimation at the early stage of development including both endogenous and exogenous variables. Although the sample is relatively small, the authors were able to fully analyze all the cost data, using no secondary sources of data (very frequent in cost modelling studies). The statistically significant variables in the cost estimation models were the areas above and below ground and the years following the 2008 financial crisis, including the international bailout (2011-2014) period. For estimating the unit cost, a nonlinear model was obtained with the number of underground and total floor, the floor ratio and the years following the 2008 financial crisis, including the international bailout (2011-2014) period as predictors. For the office buildings, it was also found a statistically significant correlation between the cost deviation and the number of underground floors.

This paper mainly focuses on the construction of a household welfare index to examine the welfare impact of international remittances in rural Bangladesh. This paper, in achieving this objective, uses primary data and several methods. This paper constructs a household welfare index newly to measure the level of household welfare. Besides, a linear regression and Chi-square test is used to examine the welfare and poverty impact of international remittances, respectively. Remittance receiving households enjoy the higher level of welfare more than non-recipient households in the study area. Household welfare is augmented by 0.116 if the household is under the shade of international remittances. A significant impact of international remittances on the reduction of household poverty is also found in this study. Therefore, this paper suggests policymakers for utilizing international remittances as a significant tool to enhance household welfare and to reduce household poverty.

We estimate the effect of household social expenditure on vulnerability to poverty using the four latest cross-sectional waves of Ghana Living Standard Survey (GLSS) from 1999 to 2017. Using a 3-Stage Least Square and Quantile Regression, our results show a widening consumption ex-post welfare gap between the poorest households and the non-poor households in a per-cedi social expenditure. Also, we estimate the probability of an ex-ante poverty using vulnerability to expected poverty. The results, however, indicate that regardless of poverty status, household vulnerability to poverty increased consistently between 1999 and 2017, and the very poor households showing the severest vulnerability. Hence, it is concluded that social expenditure increases the chances of a poor household falling into chronic poverty a non-poor household into transient poverty in the future.

Researchers have explored primary colour-geometric shape associations since Kandinsky's correspondence theory. However, there is a gap in the literature regarding interior colour applications on surface shapes. To address this gap, an online study was employed to gather data with one hundred participants who were asked to choose their preferred colours for shapes on bedroom walls with follow-up questions on the colour-shape semantic associations, their preference of colours and shapes on bedroom walls independently in addition to their favourite colour, their favourite shape, and colour-shape pairs without interior context. The results revealed that colour-shape preferences in interiors differ from those found in psychology studies, other colour applications on bedroom walls, and other preferences, indicating that colour preference is context-dependent. Interestingly, the most popular colour for surface shapes on bedroom walls is purple, followed by brown and blue. The study contributes to the existing literature by providing colour charts for bedroom applications for professionals in the industry, their clients/users, and future studies.

The construction of earth buildings, both throughout history and in the current day, is well-established worldwide. Despite New Zealand's pre- and post-colonial history of earth construction, earth buildings as residential homes have not been well-received or popularised throughout present-day New Zealand. This research aims to identify the reasons for this lack of awareness and to determine methods that promote earth buildings in New Zealand. This research is based on data collected from semi-structured interviews conducted with subject matter experts and via an online questionnaire completed by members of the Earth Building Association New Zealand (EBANZ). The data collected revealed the experiences and perceptions of all participants regarding the advantages, challenges and promotion of earth buildings specific to New Zealand. Upon analysing these responses, key reoccurring themes were identified and compared. Regarding New Zealand's lack of awareness of earth buildings, interview and questionnaire participants responded that this shortcoming was due to earth construction being a very niche market and lacking commercial marketing. Education was the most frequently reoccurring theme raised by all participants as the top promotional tool for raising awareness of earth buildings. The results of this research can be applied to future work regarding obstacles that limit the growth of New Zealand's earth building industry, as well as research on the role of New Zealand's education system in exposing the next generation of builders, designers, and consumers to earth construction.

Washing machines are one of the tools that bring great convenience to people's daily lives. However, washing machines that have been used for a long time often develop issues such as odor and mold, which can pose health hazards to consumers. There exists a conspicuous gap in our understanding of the microorganisms that inhabit the inner workings of washing machines. In this study, samples were collected from 22 washing machines in Shanghai, China, including both water eluted from different parts of washing machines and biofilms. Quantitative qualitative analysis was performed using fluorescence PCR quantification and microbial communities were characterized by high throughput sequencing (HTS). It showed that the microbial communities in all samples were predominantly composed of bacteria, and they have a strong adhesion ability in the washing machine environment. HTS results showed that in the eluted water samples, the bacteria mainly included Pseudomonas, Enhydrobacter, Brevibacterium and Acinetobacter. On the contrary, in biofilm samples, Enhydrobacter and Brevibacterium were the predominant bacterial microorganisms. Correlation analysis results revealed that microbial colonies in washing machines were significantly correlated with years of use and the type of detergent used to clean the washing machine. As numerous pathogenic microorganisms can be observed in the results, effective preventive measures and future research are essential to mitigate these health problems and ensure the continued safe use of these household appliances.

In the advent of COVID-19 pandemic, testing is highly essential to be able to isolate, treat infected persons, and finally curb transmission of this infectious respiratory disease. Group testing has been used previously for various infectious diseases and recently reported for large-scale population testing of COVID-19. However, possible sample dilution as a result of large pool sizes has been reported, limiting testing methods’ detection sensitivity. Moreover, the need to sample all individuals prior to pooling overburden the limited resources such as test kits. An alternative proposed strategy where test is performed on pooled samples from individuals representing different households is presented here. This strategy intends to improve group testing method through the reduction in the number of samples collected and pooled during large-scale population testing. Moreover, it introduces database system which enables continuous monitoring of the population’s virus exposure for better decision making.

Fire accidents are common accidents amongst residential house occupants in Libya. Some of the factors that can mitigate fire accidents in Libyan residential houses include fire safety awareness and knowledge. This study investigated the level of awareness and knowledge of fire safety amongst residential house occupants in Libya. The possibility and consequences of fire hazards and risk existing in residential houses in Libya were also studied. Experimental data obtained for 1.5 m/s and 3.5 m/s as walking and running evacuation time, respectively amongst residential house occupants in Libya were also compared. The sample consist of 90 respondents with instruments of fire safety awareness and knowledge, fire hazard and consequences, and the involvement of residential house occupants in fire emergency. Statistical analysis was performed at p < 0.05 to determine the levels of residential awareness and knowledge regarding fire safety and the hazard and consequences. The findings illustrated that the items were highly reliable (α > 0.7) and normally distributed. Also, the results illustrated that the majority of residential house occupants in Libya have fair level of fire safety awareness and knowledge with overall percentage of 80% and 90%, respectively. On the other hand, the results further showed that majority of residential house occupants have good level of fire emergency involvement with 90%. This paper proposes a fire safety assessment method which may form the basis of future fire safety practice in Libya.

This research paper aims to evaluate and model the performance of rice husk gasifier cook stoves for household energy use, a byproduct of rice milling. The study aims to address environmental issues and promote the use of rice husk as a renewable energy source and pest repellent in stoves. The study compared insulated and non-insulated gasifier stoves using rice husk gasification. The study compared the start-up time of insulated and non-insulated gasifier stoves, where the insulated stove showed a lower start-up time, but there was no significant difference at a 5% probability level. The temperature change also was not significant, as heat transfer and temperature change started when the husk was ignited. The burner stoves had different size and volume. The maximum operated or flame temperature was 1,190.30oC at room or minimum temperature of 27.33 oC, whereas the average temperature was 758.916oC for the non-insulated type of gasifier stove. The insulated gasifier stove also observed maximum and average temperatures of 518.30 oC and 289.014oC respectively at the same room temperature. The operating time of stoves directly influences the fuel consumption rate, specific gasification rate, and combustion zone rate of stoves. The fuel consumption rate has a significant effect on the type of gasifier stove, with the maximum rates being 3.820 and 2.099 kg/hr. The time to consume rice husks to gasify them depends on the density of the rice husk, reactor volume, and fuel consumption rate. The average specific gasification rate for insulated and non-insulated stoves is 106.45 and 120.63 kg/m2h, respectively. The fuel or rice husk holding capacity of each type of stove is significant at a 5% level, with the amount of rice husk and biochar produced being 1.18kg and 0.27kg for insulated stoves, and 2.511kg and 0.688kg for non-insulated stoves, respectively. The performance of gasifier stoves varies based on the bio char conversion rate, with non-insulated stoves producing a higher bio char mass per rice husk. Multiple regression analysis was used to model the relationship between time elapse with temperature and heat energy. The Squirrel-2020 data logger was used to measure the temperature produced by burning rice husks in the reactor of the stove as well as related generated and losses of heat. A relationship between the heat energy produced and the operating time of gasifier stoves was conducted to estimate the model. The cubic polynomial model was found to be the best predictive model fit for all variables of this study.

Household waste is the primary source of environmental pollution due to global population growth compared to other sources of waste. This research aims to develop a smart and integrated household waste management system framework. The resulting framework not only focuses on dimensions of information technology but also links it with other integrated dimensions. This research attempts to conduct a Systematic Literature Review (SLR) using the Preferred Reporting Items for Systematic Review and Meta-analysis (PRISMA) protocol to produce a smart and integrated household waste management framework. The framework's design is carried out by identifying the type of household waste management process based on the Integrated Sustainable Waste Management (ISWM) framework, dimensions that support smart household waste management, and stakeholders involved. The SLR results, namely dimensions and subdimensions that support the framework of a smart and integrated household waste management system, were validated by a resource person from the Indonesian Ministry of Environment and Forestry. The smart and integrated household waste management framework that has been developed in this research contains five main dimensions: Information Technology, Operational Infrastructure, Governance, Economy, and Social-culture. This framework also addresses stakeholder engagement to support smart household waste management systems and identifies waste management processes based on the ISWM framework. This research uses the PRISMA technique to provide a framework for smart and integrated household waste management systems in the initial stage. The proposed framework has been validated and can be further developed as a smart and integrated household waste management system. This research also contributes to the involvement of various dimensions identified to deal with waste problems.

In Low and Lower-Middle-Income countries, the prevalence of anemia in infancy remains high. In early childhood anemia cause irreversible cognitive deficits and represents a higher risk of child mortality. The consequences of anemia in infancy are a major barrier to overcome poverty traps. The aim of this study was to analyze based on a multi-level approach, different factors associated with anemia in children 6–23 m old based on recent available Standard Demographic Health Surveys (S-DHS). We identified 52 S-DHS that had complete information in all covariates of interest in our analysis between 2005 and 2015. We performed traditional logistic regressions and multilevel logistic regression analyses to study the association between hemoglobin concentrations and household, child, maternal, socio-demographic variables. In our sample, 70 % of the 6–23 m old children were anemic. Child anemia was strongly associated with maternal anemia, household wealth, maternal education and low birth weight. Children fed with fortified foods, potatoes and other tubers had significantly lower rates of anemia. Improving overall household living conditions, increasing maternal education, delaying childbearing and introducing iron rich foods at six months of age may reduce the likelihood of anemia at in toddlerhood.

Population is the main driver of land systems and environmental change. However, the population is usually treated as a variable that only considers the population number, and the multidimensional population structure is largely ignored. There has been a systematic transition of population structure in the past several decades, such as the changing household structure, the increasing aging population and divorce rate, and human migration. All these have direct or indirect impacts on land use and environmental issues. Here, we will take China as an example to examine the relationship between household dynamics and land use change in China by exam-ining changes in household structure and land use change in China between 1980 and 2020. The results show:1) the number of households increased by 130.95% from 1980 to 2020, while the population only increased by 42.83%. The size of households decreased from 4.41 to 2.92 in China from 1982 to 2020. The household dynamics vary from province to province, which is affected by urbanization rate and economic development. 2) Birth rates, divorce rates, population aging, and migration all affect household structure, which directly or indirectly affects changes in land use systems. 3) The changes in China's land use are interlinked and interact with changes in household structure, evident in the increase in residential land use and the abandonment of arable land. The rising household number increased the area of urban and rural settlement, leading to the fragmentation of cultivated land and the reduction of ecological land. To regulate land use change for sustainable development, future land use planning should take into effect of household dynamics, and reduce the negative effects of household dynamics on land systems and environmental change.

This study empirically investigates the effect of productive safety net programme (PSNP) on household food consumption and dietary diversity in Ethiopia. The study applied random effects with instrumental variable to estimate the effect of PSNP membership. The result of the study indicates that though PSNP membership improves household food consumption, it reduces household dietary diversity score. Household food consumption and dietary diversity are also significantly influenced by sex, age, education status of household head, household size, livestock ownership, distance to the nearest market and participation in non-farm activities. The findings of this study suggest that PSNP membership should be reinforced by building household awareness of the benefits of consuming a variety of foods. In addition, PSNP membership should be designed to endow the households to accumulate essential assets, especially livestock.

This study aims to identify the factors determining the income of forestry household in South Korea. We examine an empirical analysis using 3-year panel data conducted by the Korea Forest Service charged with maintaining South Korea's forest lands. The hypothesized factors determining the income of forestry household are classified into four types of assets and three types of livelihood strategies. We divided the income of forestry household (IFH) into three elements: forestry income (FI), non-forestry income (NFI), and transfer income (TI). We assessed the influences of household assets and livelihood strategies on each income. A random effect model was used as a statistical analysis with valid 979 of forestry household for three years. We found that household head's age, labor hours, savings, business category, cultivated land size, and region are significantly associated with IFH. Also, FI is influenced by labor capacity, cultivated size, business category, forestry business portfolio, and region while NFI is determined by household head's age, household head's gender, forestry business portfolio, and savings. TI is affected by household head's age, household head's education level, forestry business portfolios, savings, and region. The effect sizes and directions vary across different types of income (IFH, FI, NFI, and TI). The findings show that forestry in South Korea is highly dependent on sustainable assets and strategies. It is therefore expected that the effectiveness of forest policies to increase the income of forestry household would be differed by the source of each income. The results of this study draw attention to the need for an income support policy that should consider the characteristics of household assets and livelihood strategies in order to enhance IFH in South Korea.

The study follows the interaction between the individual and the social context regarding the development of adolescents protected in residential houses from the child protection system in Iasi County, Romania. Starting from the evidence that in situations of providing relatively identical material and social resources, the results obtained by these children vary greatly, we examine how the meaning (understood mainly as purpose and mattering) can constitute a developmental resource. Considering theoretical models and previous research, the study aims to describe, through a qualitative approach, how these young people see themselves and the external environment (family and residential care), how they project their future (their purpose and objectives), and how these constructions and perceptions can influence their quality of life and social integration. We conducted three focus groups with 35 adolescents and young people (the ages 13-21) protected in and for different periods in residential houses (period 1-20 years). The results highlighted that a specific meaning is reconfigured as compensatory when affected by a trauma or adverse external event and thus can be a resource for resilience. On the other hand, the research highlighted that only the existence of goals alone is insufficient to generate action, and the unrealistic meanings given to own persons, experiences, and resources can be dangerous.

In this study, we evaluated the physicochemical and microbial qualities of source and stored household waters in some communities in Southwestern Nigeria using standard methods. Compared parameters include physicochemical constituents; Temperature (T), pH, Total Dissolved Solids (TDS), Total Hardness (TH), Biological Oxygen Demand (BOD), Magnesium ion (Mg²⁺) and Calcium ion (Ca²⁺) and microbiological parameters included Total Coliform Counts (TC), Faecal Coliform Counts (FC), Fungal Counts (Fung C), Heterotrophic Plate Counts (HPC). Comparing Stored and Source samples, the mean values of some physicochemical parameters of most of the stored water samples significantly (P<0.05) exceeded that of Sources and ranged in the following order: T (15.3±0.3^oC - 28.3±0.5^oC), pH (6.4±0.1 - 7.6±0.1), TDS (192.1±11.1 ppm - 473.7±27.9 ppm), TH (10.6±1.7 mg/L - 248.6±18.6 mg/L), BOD (0.5±0.0 mg/L - 3.2±0.3 mg/L), Mg²⁺ (6.5±2.4 mg/L - 29.1±3.2 mg/L) and Ca²⁺ (6.5±2.4 mg/L - 51.6±4.4 mg/L). The mean microbial counts obtained from microbial comparison of different points (Stored and Source) of collection showed that most of the stored water had counts significantly exceeding (P<0.05) those of the source water samples (cfu/100 mL) which ranged as follows: TC (3.1±1.5 - 156.8±42.9), FC (0.0±0.0 - 64.3±14.2) and HPC (47.8±12.1 - 266.1±12.2) across all sampled communities. Also, the predominant isolates recovered from the samples were identified as Escherichia coli, Klebsiella pneumonia, Pseudomonas aeruginosa, Enterobacter aerogenes, Aspergillus spp, Mucor spp, Rhizopus spp and Candida spp. The presence of these pathogenic and potentially pathogenic organisms in the waters and the high counts of the indicator organisms suggest the waters to be a threat to public health.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.

To assess the efficacy of washing cloth masks, we simulated SARS-CoV-2 contamination in tricoline fabric and tested decontaminants to reduce viral particles. Viral suspensions using two variants (B.1.1.28 and P.1) were inoculated in these fabrics, and the inactivation kinetics were evaluated after washing with various household disinfection products (Soap powder, Lysoform®, Hypochlorite sodium and 70% Alcohol), rinse numbers, and exposure times. Afterward, the fabrics were washed in sterile water, viral RNA extracted and amplified using RT-qPCR. Finally, viral replication in cell cultures was examined. Our findings show that all biocidal treatments successfully disinfected the tissue tested. Some products showed less reduction in viral loads, Soap powder (1.60 x 104, 1.04 x 103), Soap powder and Lysoform® (1.60 x 104, 1.04 x 103) and Alcohol 70% (1.02 x 103, 5.91 x 101) respectively. However, when sodium hypochlorite was used, this reduction was significantly increased (viral inactivation in 100% of the washes). After the first wash, the reduction of viral particles was greater for the P.1 variant than for the B.1.1.28 variant (W = 51759, p 0.05). In conclusion the sodium hypochlorite role on cloth masks disinfection may also have implications for future health emergencies as well as recommended by WHO.

In recent years, Malaysia has faced environmental challenges caused by municipal solid waste, especially household waste, during the Covid-19 pandemic. Among all the household waste, plastic and paper are the most prominent waste that causes environmental hazards. Several recycling associations in Malaysia have carried out their practices for better waste sustainability and management to curb the increasing amount of household waste. However, the effectiveness is still vague in achieving smart and effective household waste management. Therefore, this paper aims to investigate Malaysia’s household waste management, mainly in three significant municipalities in Malaysia for Kuala Lumpur, Penang and Melaka, in becoming a resilient and sustainable city by addressing two main research questions 1) What are the key factors for ensuring the more success move for future household waste management in cities? and 2) How will the 3 municipalities address their waste issues based on the key factors from RQ1, respectively? This paper reviewed 13 waste management articles and explores the potential of the four factors of waste management from the perspective of technology and data, economy, social and governance. The discussed factors and models contributed to an integrated future-proofing framework that focuses on smart waste tracking, an gamified awareness education, and strict policies to control waste management are the way forward for the future of smart cities household waste management.

Load shifting is one of the demand side management (DSM) strategies to support the efficiency in the electricity grid during the peak hours demand. Load shifting at the appliance level is interesting to review since the appliance usage is one of the main inputs in the load profile analysis. More review studies in load shifting at the appliance level are required as it is a specific issue of load profile research body, and still limited studies are available at this moment. It is also essential to focus on the appliance usage patterns to better understand the impacts and characteristics of the individual appliance. The existing studies in load shifting have applied common structured literature reviews, and our study addresses the transparency of each stage and sub-stage of the selection of the final list studies. The finding shows that efficiency has been achieved in the installed capacity reduction, cost including emission reductions, and peak consumption reduction. The most applied method in the load shifting at the appliance level is by developing the load shifting optimisation algorithms. This work contributes to provide a transparent process of applying a systematicity literature review, where it becomes a source of knowledge and grounded theory. It contributes to a limited and specific research of load shifting at the appliance level by highlighting and discussing the key findings for the readers. In specific, it contributes to improve energy efficiency by presenting the load shifting methods at the appliance level and identifying the controllable and uncontrollable appliances. This detail review study at the appliance level can make valuable contributions to support decision and policy-making by illuminating new dynamic system in load shifting area in specific, and demand side management in general for energy efficiency.

Reliable prediction of sustainable energy consumption is the key to designing environmental friend buildings. In this study, two novel hybrid intelligent methods, namely grasshopper optimization algorithm (GOA), wind-driven optimization (WDO), and biogeography-based optimization (BBO) is employed to optimize the multitarget prediction of heating loads (HLs) and cooling loads (CLs) in heating ventilation and air conditioning (HVAC) systems. Concerning the optimization of applied hybrid algorithms, a series of swarm-based iteration is performed, and the best structure for the abovementioned methods are proposed. Besides, through sensitivity analyzing the relationship between the HLs and CLs and influential factors are highlighted. In other words, the GOA, WDO, and BBO algorithm are mixed with a class of feedforward artificial neural networks (ANN), which called MLP (multi-layer perceptron) to predict the HLs and CLs. According to the provided sensitivity analysis, the WDO with swarm size = 500 proposes the most proper-fitted terms after it has been combined with optimized MLP. The proposed WDO-MLP (training (R2 correlation=0.977 and RMSE error=0.183) and testing (R2 correlation=0.973 and RMSE error=0.190)) provided accurate prediction in the heating load and (training (R2 correlation=0.99 and RMSE error=0.147) and testing (R2 correlation=0.99 and RMSE error=0.148)) presents the most-fit prediction in the cooling load.

A characteristic feature of lightweight constructions is their low thermal mass which causes high internal temperature fluctuations that require high heating and cooling demand throughout the year. Phase Change Materials (PCMs) is effective in providing thermal inertia to low thermal mass buildings. The aim of this paper is to analyse the thermal behaviour of two proposed lightweight buildings designed for homeless people and to investigate the potential benefit achievable through the use of different types of PCM in the temperate climatic conditions of Christchurch, New Zealand. For this purpose, over 300 numerical simulations have been conducted using the simulation software DesignBuilder®. The bulk of the simulations were carried out under the assumption that the whole opaque building envelope is equipped with PCM. The results showed significant energy saving and comfort enhancement through the application of PCMs. Thereby, annual energy saving of over 50 % was reached for some of the PCMs considered. Additionally, the effectiveness of single, PCM-equipped structure components was investigated and substantial benefits between 19 and 27 % annual energy saving were achieved. However, occupant behaviour in terms of ventilation habits, occupancy of zones etc. remains one of the biggest challenges in any simulation work due to insufficient data.

Over the last two decades, residential buildings have accounted for nearly 50 percent of total energy use in New Zealand. In order to reduce household energy use, the factors that influence energy use should be continuously monitored and managed. Building researchers and professionals have made efforts to investigate the factors that affect energy use. However, few have concentrated on the association between household energy use and the cost of residential buildings. This study examined the correlation between household energy use and residential building cost. Analysis of the correlation between energy use data and residential building cost indicated that residential building cost in the construction phase and energy use in the operation stage were significantly correlated. These findings suggest that correct monitoring of building costs can help to identify trends in energy use. Therefore, this study proposes a time series model for forecasting residential building costs of five categories of residential building (one-story house, two-story house, townhouse, apartment, retirement village) in New Zealand. The primary contribution of this paper is the identification of the close correlation between household energy use and residential building costs and provide a new area for optimize energy management.

This paper investigates how blocks of buildings could fit into load shedding strategies. It focuses in particular on what could be the effects on peak shaving, occupants’ thermal comfort or CO2 emissions reduction and how to quickly quantify them. To achieve this goal, we focused on a new residential district, thermally fed by heat pumps. Four modeling approaches were confronted in order to estimate buildings' responses to load shedding orders. On the one hand, a quick estimation of the peak shaving impact can rely on experimental results if the buildings' envelope and uses of the experimentation match those of the study case. On the other hand, thermal simulation models allow us to assess thermal comfort while considering the building physical response. Finally, a hybrid modeling approach can provide a good compromise between modeling rapidity and accuracy of the impacts estimation. At district scale, it may be necessary to mix modeling approaches, from experimental results to detailed thermal models. Accuracy is not guaranteed for all approaches so that the choice should be made carefully in regards to study needs. However, results are sufficient to compare the effects of load shedding strategies on peak shaving, thermal comfort, and CO2 emissions reductions.

The consistently positive Australian economic environment and stable population increase have led to a higher demand for new houses in recent years. Prefabrication is a promising method to help alleviate the issues related to housing shortage and affordability due to reduced material wastage, construction delays due to weather conditions, unexpected costs, shortage in labour and onsite risks. With the advancements in automation and manufacturing methods such as Design for Manufacturing and Assembly (DfMA), the quality and precision of prefabricated materials is tightly controlled, and the fabrication and assembly period are reduced. However, the full potential of prefabricated construction is yet to be realised in part due to most of developments being focused on its superstructure. A review of the current available options suitable for houses is necessary to understand the present state of the residential footing industry, which will help evaluate the necessary innovations for the growth of the Australian construction industry considering the local reactive soil conditions. This paper presents a summary of existing footing systems and potential prefabricated footing solutions for low-rise residential structures with one storey to two storeys. This paper also reviews the benefits and challenges of designing, manufacturing, transporting, handling and installing of prefabricated footings on site, which have great influence on the acceptance of these innovative footing systems.

The article examines the relationship between household food waste and GDP in various European regions, aiming to determine how economic prosperity influences household food waste levels. Using comparative analysis of secondary and tertiary data, we developed a synthetic indicator (IpFW), to assess the interaction between GDP per capita and household food waste per capita. Despite expectations, higher GDP did not consistently correlate with lower food waste, challenging assumptions about economic prosperity and environmental stewardship. The research underscores the complex interplay between economic factors and food waste management, revealing no significant correlation even at regional levels. It also highlights the potential of e-commerce in enhancing food waste reduction strategies. E-commerce platforms can optimize food supply chains and consumer behavior, contributing to more sustainable consumption patterns. The conclusions call for a reevaluation of policies and suggest that integrating e-commerce could bolster efforts to manage food waste more effectively, aligning with the Sustainable Development Goals.

The ever deepening population aging has brought opportunities and challenges to the continued expansion of tourism consumption in China. In this article, the impact of population aging on household tourism consumption was studied from both theoretical and empirical aspects. First, the micro mechanisms of the impact of population aging on household tourism consumption were analyzed, which include economic condition mechanism, intergenerational care mechanism, health status mechanism and Internet use mechanism. Subsequently, the impact of population aging on household tourism consumption and its impact mechanisms were tested, and the heterogeneity analysis was conducted, by using the data of China Family Panel Studies (CFPS) from 2014, 2016 and 2018. The main conclusions of the article are as follows: (1) Population aging has a significant negative impact on household tourism consumption, and a series of robustness test results such as endogenous treatment support this finding. (2) The results of the impact mechanism test show that population aging has a negative mediating effect on household tourism consumption by reducing household economic conditions. The moderating effect of intergenerational care on the effect of population aging on household tourism consumption is insignificant. Health status of the elderly and Internet use have a significant positive moderating effect on the impact of population aging on household tourism consumption. (3) The results of the heterogeneity analysis show that the negative impact of population aging on household tourism consumption in urban areas is greater than that in rural areas, and the negative impact of population aging on household tourism consumption of families with the old-old elderly is greater than that of falimies with the young-old elderly. The conclusions of this article provide important references for activating tourism consumption in China in the context of population aging.

Micronutrient deficiencies are a major public health problem. Beans are an important plant-based source of iron, zinc and copper, but their absorption is reduced in the presence of anti-nutrients such as phytates, polyphenols and tannins. Soaking and discarding the soaking water before cooking is unanimously recommended, but this can result in mineral loss. Data on the consequences for mineral bioaccessibility is still limited. This study aimed to evaluate iron, zinc and copper bioaccessibility in black beans cooked (regular pan, pressure cooker) with and without the soaking water. Minerals were quantified by ICP-MS, myo-inositol phosphates (InsP₅, InsP₆) by HPLC ion-pair chromatography, total polyphenols using Folin-Denis reagent and condensed tannins using Vanillin assay. Mineral bioaccessibility was determined by in vitro digestion and dialysis. All treatments resulted in a statistically significant reduction of total polyphenols (30%) and condensed tannins (20%). Only when discarding the soaking water a loss of iron (6%) and copper (30%) was observed, and InsP₆ was slightly decreased (7%) in one treatment. Bioaccessibility of iron and zinc were low (about 0.2% iron and 35% zinc), but copper presented high bioaccessibility (about 70%). Cooking beans under pressure without discarding the soaking water resulted in the highest bioaccessibility levels among all household procedures. Discarding the soaking water before cooking did not improve the nutritional quality of the beans.

In 2023, residential and commercial sectors together consumed approximately 27.6% of total U.S. energy, equivalent to about 20.6 quadrillion Btu. Factoring in the electrical system energy losses, the residential sector represented approximately 19.7% of total U.S. energy consumption during that time. There were approximately 144 million housing units in the United States in 2023, which is increasing yearly. In this study, information on energy usage in the United States (U.S.) residential sector has been analyzed and then represented as energy intensities to establish benchmark data and to compare energy consumption of varying sizes and locations. First, public sources were identified, and data from these previously published sources were aggregated to determine the energy use of the residential sector within the US. Next, as part of this study, the energy data for seven houses/apartments from five different United States climate zones were collected firsthand. That data was analyzed, and the energy intensity of each home was calculated and then compared with the energy intensities of the other homes in the same states using RECS data. The energy intensity for each facility was calculated based on the actual energy bills. Finally, the study evaluated the carbon footprint associated with residential energy consumption in all 50 states to reinforce the importance of sustainable development initiatives.

The quality of the environment affects human behavior, the micro-communities of human beings need creative thinking and ideas. Social environments have a significant impact on collective behaviors and social interactions. Nowadays achieving social indicators in housing with a sustainable approach is one of the goals that have been considered. The most important issue in the field of research is recognizing and examining the value of spaces in residential environments to achieve social life, in which it leads human to be social in public residential spaces. Paying attention to social relations with neighbors and people to create Social relationships are proportionate to the presence of individuals in their realm of life. The concept of neighborhood is being responsible for creating social relationships, influencing people living in the complex and community-based life. In this research, by satisfying the human need to communicate and interact with others, creating collective spaces in different scales such as commercial and recreational spaces in residential complexes, the presence of people in these spaces leads to the socialization of collective space and the factor in which the space achieves success. By explaining and identifying the components of socialization in the collective spaces of residential complexes, such spaces can be prepared for the presence of people in the space.

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

Few studies have explored the gender wage gap among farmworkers, and there is a notable absence of research on how farm wages impact household welfare differently based on gender. This study aims to fill this gap by examining how farm wages affect gender disparities in household welfare among farmworkers in Nigeria. Using survey data from 720 farmworkers, we investigated gender-based differences in household welfare. Our approach combined parametric methods (Blinder-Oaxaca decomposition) to assess gender gaps in household welfare and non-parametric techniques (Propensity Score Matching, PSM) to estimate the effects of farm wages. The analysis reveals that female farmworkers experience significantly lower per capita food consumption expenditure (₦11,486.51 less) compared to their male counterparts. These disparities partly stem from differences in socioeconomic factors, job characteristics, and enterprise attributes between male and female farmworkers. The study underscores the role of farm wages in mitigating gender gaps in household welfare, demonstrating that farm wages have increased per capita food consumption expenditure for female farmworkers by ₦6,640.698. This finding highlights the potential of wage increases to enhance livelihoods, underscoring the importance of equitable wage policies in farming. Furthermore, our findings emphasize that the impact of farm wages on welfare varies with household characteristics, suggesting the need for targeted interventions tailored to enhance identified household attributes. Addressing these factors could effectively reduce gender inequalities in farm work and contribute to overall welfare improvements.

Residential segregation refers to the phenomenon where people of different socioeconomic backgrounds live in spatially separated areas. It is essential to ensure equitable access to urban amenities for all residents in pursuit of the normative values in urban planning. To achieve this planning goal, the disparity in accessibility to urban amenities needs to be appropriately diagnosed. Private apartments and public rental apartments are representative types of residences where residential segregation is likely to occur in the context of South Korea, since these two types show considerable differences in the education, income, and occupations. The objective of this study is to develop an analysis framework for diagnosing the difference in accessibility to urban amenities between the two residential types, and to empirically demonstrate their utility in the planning process. The empirical analysis conducted on Seoul revealed that not only were there significant local variations in accessibility between the two segregated residential areas, but the overall differences across the entire area were also pronounced. The proposed framework is useful in supporting decision-making processes for locating new public facilities or identifying regional priorities for guiding the placement of private amenities, with the aim of mitigating differences between segregated residential areas.

Western countries are experiencing an increasing aging population, resulting in heightened disability and mobility issues. This trend is expected to escalate in the coming decades. Therefore, ensuring adequate accessibility in collective residential housing –where individuals spend much of their daily lives– is of paramount importance. This paper presents a case study focused on the accessibility of building entrances in collective residential housing in Southeast Spain, specifically in the Region of Murcia. In this region, 9.8% of the population has disabilities, and 15.75% were over 64 years old in 2020. The study began by compiling the relevant national and regional accessibility regulations for existing buildings. Subsequently, extensive fieldwork was conducted, analyzing 150 collective residential housing buildings. Based on this analysis, a set of recommendations to enhance accessibility was formulated for buildings not complying with the regulations. The results are presented and discussed in detail. The most frequent recommendation was the construction of accessible ramps, identified as the primary solution in over 40% of cases, either alone or in conjunction with other measures. In 54% of the cases, multiple interventions were necessary to achieve effective accessibility adaptation. The findings of this study could inform the development of public policies aimed at improving accessibility conditions in urban areas.

Mechanical ventilation systems used in houses are designed to reduce carbon dioxide emissions while minimizing the energy loss resulting from ventilation. However, increase in indoor fine particulate (PM2.5) concentration because of external PM2.5, influx through the ventilation system poses a problem. In this study, we analyzed the changes in indoor PM2.5 concentrations via dis-tinguishing between cases of high and low outdoor PM2.5 concentrations, considering the effi-ciency of filters used in residential mechanical ventilation systems. When using minimum effi-ciency reporting value (MERV) 10 filters in the ventilation system, the outdoor PM2.5 concentra-tion was 5 μg/m³; the indoor PM2.5 concentration became 73% after 60 min compared to the ini-tial. When the outdoor PM2.5 concentration was 30–40 μg/m³, the indoor PM2.5 concentration reached 91%. However, when MERV 13 filters were used, the indoor PM2.5 concentration con-sistently dropped to 73–76% regardless of the outdoor PM2.5 concentration. Furthermore, by comparing the established equation with the mass-balance model, the error was confirmed to be within 5%, indicating good fit. This allows the prediction of indoor PM2.5 under various condi-tions when using mechanical ventilation systems, enabling the formulation of strategies to maintain indoor PM2.5 as recommended by the World Health Organization.

Residential satisfaction with post-disaster housing is crucial for the success and sustainability of a resettlement project. However, little attention has been given to this aspect in the permanent houses developed after the 2015 Gorkha earthquake. To bridge this gap, the study examined factors affecting residential satisfaction among poor displaced households resettled in the Panipokhari Integrated Settlement of Nepal. Data were collected through a questionnaire survey, interviews, and field observation. Internal consistency and reliability were assessed using Cronbach's Alpha test, while satisfaction was measured by mean satisfaction scores. The relative importance index ranked the factors, and Spearman's rank correlation coefficient analyzed their relationship with overall residential satisfaction. The study identified several crucial fac-tors influencing residential satisfaction, including the design and layout of the house, space for modification, provision of a kitchen garden and cattle shed, thermal comfort, completeness of the house, provision of a hearth, and spaces for rituals and cultural events. These findings shed light on the resettlement decisions of affected populations and provide valuable insights for policymakers, implementers, and researchers aiming for successful and sustainable resettlement outcomes.

This publicly available simulation analysis compares baseline construction options versus sustainable options and evaluates both break-even costs as well as environmental effects. The simulation (https://rminator.shinyapps.io/sustain4/) provides users with comparative estimates based upon existing research on costs. This is the first simulation of its type that quantifies multiple sustainable construction options, associated break-even points, and environmental considerations for public use. Results estimate that a 100% solar solution for the baseline 3,000 square foot / 279 square meter house with 2 occupants results in a break-even of 9 years. The simulation includes options for rainwater harvesting or wells, Icynene foam, engineered lumber, Energy Star windows and doors, low flow water fixtures, aerobic / non-aerobic waste treatment or municipal services, and many other options. This is the first simulation of its type to provide publicly available sustainable construction analysis based on research, and it illustrates that sustainable construction might be both green for the environment and green for the pocketbook.

Residential coal combustion is one of the most significant sources of carbonaceous aerosols in the Highveld region of South Africa, significantly affecting the local and regional climate. In this study, we investigated single coal-burning particles emitted when using different fire-ignition techniques (top-lit up-draft vs bottom-lit up-draft) and air ventilation rates (defined by the number of air holes above and below the fire grate) in selected informal braziers. Aerosol samples were collected on nucleopore filters at the Sustainable Energy Technology and Research Centre Laboratory, University of Johannesburg. Individual particles (~700) were investigated using a scanning electron microscope equipped with energy-dispersive X-ray spectroscopy (EDS). Two distinct forms of spherical organic particles (SOPs) were identified, one less oxidized than the other. The particles were further classified into "electronically" dark and bright. EDS analysis showed that 70% of the dark spherical organic particles had higher (~60%) relative oxygen content than in the bright SOPs. We quantified the morphology of spherical organic particles and classified them into four categories: ~50% are bare single particles; ~35% particles are aggregated and form diffusion accretion chains; 10% have inclusions, and 5% are deformed due to impaction on filter material during sampling. We conclude that there are two distinct kinds of coal burning spherical organic particles and that dark SOPs are less volatile than bright SOPs. We also show that these spherical organic particles are similar in nature and characteristics to tar balls observed in biomass combustion and that they have the potential to absorb sunlight thereby affecting the earth’s radiative budget and climate. This study provides insights into the mixing states, morphology, and possible formation mechanisms of these organic particles from residential coal combustion in informal stoves.

Cost estimating based on building cost index plays an important role in project planning and management by providing accurate cost information. Recently, tremendous advances in cost estimating has been made but serious inaccuracies in it are still too frequently witnessed. This study aims to improve estimating accuracy for residential building costs in New Zealand. In this study, the New Zealand house prices index is involved in the transfer function models to produce forecasts of building costs for one-storey house, two-storey house, and town house in New Zealand. To demonstrate the effectiveness of the proposed models, this study compares the estimate results of the transfer function models with the univariate ARIMA models. The results indicate that the proposed transfer function models can achieve better outcomes than ARIMA models by considering the causality between building costs and New Zealand house prices. During the modelling process, the better cost estimation approach can be identified, and the movements of building costs are shown.

To enable net zero sustainable thermal building energy this study develops an open-source thermal house model to couple solar photovoltaic (PV) and heat pumps (HP) for grid-connected residential housing. The calculation of both space heating and cooling thermal loads and the selection of HP is accomplished with a validated Python model for air-source heat pumps. The capacity of PV required to supply the HPs is calculated using an System Advisor Model integrated Python model. Self-sufficiency and self-consumption of PV and the energy imported/exported to the grid for a case study are provided, which shows that simulations based on the monthly load profile have a significant reduction of 43% for energy sent to/from the grid compared to the detailed hourly simulation and an increase from 30% to 60% for self-consumption and self-sufficiency. These results show the importance of more granular modeling and also indicate mismatches of PV generation and HP load based on hourly simulation datasets. The back-calculation PV sizing algorithm combined with HP and thermal loads presented in this study exhibited robust performance. The results indicate this approach can be used to accelerate the solar electrification of heating and cooling to offset the use of fossil fuels in northern climates.

Measuring and predicting Carbon Emission (CE) is important to enabling the main culprit of various urgent environmental issues including global warming. However, prior studies did not fully incorporate the impact of micro-level urban streetscapes, which might lead to biased prediction of urban CE. To fill the gap, we developed an effective framework to predict residential CE in urban areas from widely existing and publicly available street-view images (SVI) using machine learning. First, we used a semantic segmentation algorithm to classify more than 30 streetscape elements from SVI images to describe the built environment whose features might affect residential and transportation CE. Second, based on the streetscapes quantified, we trained a 10-fold cross-validation method with various machine learning models to predict the CE at the 1KM grid level using CE data from the PlanetData. We found first, built environment features such as sidewalks, roads, fences, buildings, and walls are significantly correlated with the residential CE. Second, the presence of buildings and subtle streetscape features (e.g., walls, fences) indicates higher-density residential areas which are related to more residential CE. Third, vegetation (e.g., trees and grass) are reversely related to residential CE. Our findings shed light on the feasibility of using a single and open data source (i.e., the SVI) to effectively model neighborhood-level CE for regions across diverse urban forms. Our framework is useful for urban planners to inform new town development and urban regeneration towards the low CE goals.

The visual perception of leisure spaces between residences in cold regions is important for public health. To compensate for the existing researches` lack of ignoring the cold snow season`s influence, this study selected two types of outdoor leisure space environments in non-snow and snow seasons as research objects. An eye tracker combined with a Semantic Difference (SD) questionnaire was used to verify the feasibility of the application of virtual reality technology, screen out leisure gaze characteristics, and reveal the environmental factors related to leisure visual perception. In snow season, spatial aspect ratio (SAR), building elevation saturation (BS), and grass proportion in the field of view (GP) showed strong correlation to the leisure visual perception scores (W). In non-snow season, apart from the above three factors, roof height difference (RHD), tall tree height (TTH) and color contrast (HC) also influenced W obviously. The effects of factors on W were revealed in immersive virtual en-vironment (IVE) orthogonal experiments and genetic algorithm (GA) and k-nearest neighbor algorithm (KNN) were combined to optimized the environmental factors. The optimized threshold ranges in the non-snow season environment were SAR: 1.82‒2.15, RHD: 10.81 m‒20.09 m, BS: 48.53‒61.01, TTH: 14.18 m‒18.29 m, GP: 0.12‒0.15, and HC: 18.64‒26.83. In the snow season environment, the optimized threshold ranges were SAR: 2.22‒2.54, BS: 68.47‒82.34, and GP: 0.1‒0.14.

Brick is widely used in construction, but it often becomes debris due to its use and lack of quality. In Ecuador, brick production is not completely industrialized, resulting in deficient properties for construction. In the city of Loja, most bricks come from artisanal factories . This research proposes the use of geopolymerization and waste bricks to create a sustainable material in construction. Geopolymerization processes were employed with sodium hydroxide as the alkaline activator. The resulting products underwent various tests to obtain the optimal formula in terms of material behavior and strength. Physical and mechanical property tests were conducted, and their application in building envelopes for low-income housing was analyzed. The results showed that the new material, when used as cladding on facades, can reduce heating and cooling demand. In a case study in Loja, a significant decrease in heating and cooling degree days was observed. This research opens new possibilities in the utilization of recycled materials in construction and can contribute to knowledge in this field.

Cultural practices and development level can influence a population’s household structures and mixing patterns. Within some populations households can be organized across multiple dwellings. This likely affects the spread of infectious disease spreads through these communities, however, current demographic data collection tools do not record these data. Methods: Between June–October 2018, the Contact And Mobility Patterns in remote Aboriginal Australian communities (CAMP-remote) pilot study recruited Aboriginal mothers with infants in a remote northern Australian community to complete a monthly iPad-based contact survey. Results: Thirteen mother-infant pairs (participants) completed 69 study visits between recruitment and the end of May 2019. Participants reported they and their other children slept in 28 dwellings during the study. The median dwelling occupancy, defined as people sleeping in the same dwelling on the previous night, was nine (range: 3.5–25). Participants who completed at least three responses (n=8) slept in a median of three dwellings (range: 2–9). Each month a median of 28% (range: 0%–63%) of the participants travelled out of the community. Including these data in disease transmission models amplified estimates of infectious disease spread in the study community, compared to models parameterized using census data. Conclusions: The lack of data on mixing patterns in populations where households can be organized across dwellings may negatively impact the accuracy of infectious disease models for these communities and the efficacy of public health actions they inform.

This paper presents a theoretical evaluation of the prices of mixed briquettes produced from co-conut shells (CCS), banana peels (BNP), rattan waste (RWT), and sugarcane bagasse (SGC), and, on the other hand, an analysis of the economic viability of their use as a replacement for conventional household fuels (Liquefied Petroleum Gas, fuelwood, and wood charcoal) in house-holds in Cameroon. The investigation was carried out using the Life Cycle Cost method on a typical household over a ten-year period with annual cooking energy requirements of 950 kWhth. The SGC-CCS and SGC-RWT mixed briquettes with a ratio higher than 7.75% and 11.1%, respectively, have prices lower than 0.063 €/kWhth. The Present Value of the Net Benefit is posi-tive for the use of SGC-CCS and SGC-RWT mixed briquettes. The results show that by making the right mixes of residues, it is possible to obtain biomass briquettes that are less expensive than conventional fuels.

Research on climacteric syndrome among middle-aged men remains scant than the research among women. Research is also scant on climacteric syndrome among older adults living alone, particularly men, who are more vulnerable than such females. This cross-sectional study investigated whether the prevalence of climacteric syndrome is associated with the type of household middle-aged men live in and identified the determinants of climacteric syndrome based on the household type. Six hundred middle-aged men living in multi-person households and 600 living alone were surveyed about general characteristics, diet-related factors, and climacteric syndrome. Data were analyzed using Pearson’s chi-squared test, Fisher’s exact test, and logistic regression. The risk of climacteric syndrome in single-person households was found to be 1.6 times higher than that among in multi-person households (p = 0.006). In multi-person households, income and breakfast frequency predicted climacteric syndrome (p < 0.05), while age, breakfast frequency, dinner frequency, and weekly eating out frequency predicted climacteric syndrome in single-person households (p < 0.05). Thus, dietary factors are more closely linked to the prevalence of climacteric syndrome in single-person households than in multi-person households. This highlights the need for climacteric syndrome interventions for middle-aged men whose health concerns may persist into older adulthood.

In various countries of the global south, school feeding programs are implemented in order to alleviate short-time hunger in children, improved their nutrition and provide employment for food vendors. The impact of these programs is important not only in terms of pupils’ nutrition but also in improving farmers’ livelihoods. This study analyzes the impact of the school feeding program on smallholders' food security based on data collected in 2021 from 240 farmers surveyed in northeast Nigeria. Differently from other studies, several econometric methods are used to analyze the data, namely, binary probit regression, propensity score matching, inverse probability weighted adjusted regression and endogenous switching regression. The results show that about 40% of the beneficial smallholder farmers are food secure compared to 20% of the non-beneficiary households. Findings revealed that the Homegrown school feeding program (HGSF) positively improved smallholder farmers improve household food security status. Results provide evidence for the need to expand school feeding programs vis-a-vis interventions in facilitating farmers’ access to capital and capacity building for better integration in the supply chain.

Mercury emissions from small-scale coal-fired boilers are still a serious environmental problem in Poland and the Czech Republic. The publication presents the results of mercury emission tests conducted using five different small-scale coal-fired boilers and five different coal fuels. The research was carried out under laboratory conditions, but also using residential users' heating devices. They covered a wide range of operational parameters, both energy and emission. It was shown that more than 94% of the mercury contained in coal fuel undergoing combustion is emitted into the atmosphere with the volatile products of combustion (including dust), and the amount of emissions is strongly dependent on the original mercury content of the fuel. One solution to the problem of mercury emissions from small-scale coal-fired boilers may be to replace traditional coal with low-emission carbon fuels. The paper shows that mercury emissions from burning such fuels are many times lower than from burning coal. The widespread use of low-emission carbon fuels in individual heating systems in Poland and the Czech Republic would reduce mercury emissions to the atmosphere by up to 90% compared to the current level of emissions generated by individual heating systems in these countries.

Residential burns camp programmes provide help and support to children with burn injuries by providing activities designed to build their confidence and self-esteem. Our regional burns service has been running camps for over 20 years and evaluation is an important part of assessing their effectiveness. In this study we report both qualitative and quantitative data from 10 consecutive years of burns camps. Qualitative feedback was gathered using Likert scales and free response questionnaires at the end of camp and six weeks post-camp. Three quantitative outcome measures, the Paediatric Quality of Life Inventory v4, the Children’s Revised Impact of Event Scale (CRIES8) and the Satisfaction with Appearance Scale (SWAP) were completed before and six weeks after camp. Children and their parents/carers both reported attending burns camp was helpful for them/their child; the themes of meeting other children with burn injuries and developing confidence and self-esteem were cited as reasons. Parents/carers also reported significant improvements in their child’s physical and psychological functioning post-camp in some years. These findings confirm the importance of providing burns camp programmes for children with burn injuries as part of their post burn rehabilitation.

Children living in residential care homes (RCH) often present conditions of abandonment due to separation, abuse and mistreatment; circumstances that are detrimental to proper emotional development, resulting in poor self-confidence, aggressive behaviors, low self-esteem, anxiety, among other developmental problems. Additionally, pandemic lockdown hinders access to mental health services for RCH service providers, and limits children to external mental health support and resources. The objective of this study was to design and evaluate the effectiveness of a remote-applied Emotional-Intelligence-based intervention program (RA-EIBI) for children living in RCH during pandemic lockdown. A non-parametric pre-test, treatment, post-test comparative design was used to evaluate effectiveness of the intervention program. Seven children living in RCH during pandemic lockdown were initially assessed using Evaluation of Neurological Soft Signs, and Empathy Quotient (EQ-I) to estimate emotional intelligence quotient. A 10 session RA-EIBI program was designed and applied to the children after initial assessment, and a final evaluation was conducted to perform related samples comparisons. Results shown a non-significant mean increase of intrapersonal, interpersonal, stress management, adaptability, and emotional state, all emotional intelligence-related skills. A RA-EIBI program is an accessible resource for RCH, and children living under this condition. EI skills were maintained along the social isolation period due to COVID-19. Followup of emotional conditions of children demonstrated an improvement in self-perceived well-being.

The global climate change mitigation efforts have increased the efforts of national government to incentivize local households in adopting individual renewable energy as a mean to help reduce the usage of electricity generated using fossil fuels and to gain independence from the grid. Since the majority of residential generation is made by PV panels that generate electricity at off-peak hours, the optimal management of such installations often considers local storage that can defer the use of locally generated electricity at later times. On the other hand, the presence of distributed generation can affect negatively the operating conditions of low-voltage distribution networks. The energy stored in batteries located in optimal places in the network can be used by the utility to improve the operation of the network. This paper proposes a metaheuristic approach based on a Genetic Algorithm that considers three different scenarios of using energy storage for reducing the losses in the network. Prosumer and network operator priorities can be considered in different scenarios inside the same algorithm, to provide a comparative study of different priorities in storage placement. A case study performed on a real distribution network provides insightful results.

Sustainability is very important in business. The residential high-rise building all firms wanted to successful and sustainability in business. There is need the construction to completed low time, low cost and high quality in construction work. Therefore, real estate developers must find various strategies to use in construction projects to achieve goals and success of the firm. The purpose of this study was to indicate the very importance of knowledge management can lead to sustainability in business. Analyze 14 critical success to sustainability in residential high-rise building projects, collected questions from literature review, and survey in deep interview senior managers of 15 projects real estate development firms listed on the stock market of Thailand. Budget building more than 1000 million baht per project. From conceptual frame work five foundations integrated to knowledge management of critical success (KMITL PROCESS) used made tool survey in deep interview the critical success to sustainability in residential high-rise building project from project managers. Used IBM SPSS evaluated the critical success to sustainability. Found was one very important of critical success to sustainability, which was quality of products x̄ = 4.83. All 14 critical success to sustainability was found can applied made the knowledge management of critical success to sustainability in residential high-rise building project in firm. Especially in the field of construction managements project can used improve of all construction projects.

In the Kingdom of Saudi Arabia (KSA), residential buildings’ energy consumption accounts for almost 50% of the building stock electricity consumption. The electricity generation consumes over one-third of the daily oil production. KSA was ranked as one of the highest countries in fossil fuel consumption per capita in 2014. Moreover, the KSA’s economy heavily relies on fossil fuel sources, namely oil reservoirs, whereby depletion will negatively affect the future development of the country. The total electricity consumption is annually growing by approximately 5-8%, which would lead to identical oil consumption to oil production in 2035. Currently, the KSA government is concerned to generate more renewable energy using large renewable energy plants. The government is investing in energy generation through renewable sources, by financing large scale photovoltaic farms to stop an economic crisis that may occur in 2035. The existing building stock consumes around 80% of the total current Saudi electricity that is generated. According to the Saudi energy efficiency report, the primary energy consumption per capita is over three times higher than the world average. Therefore, the residential buildings need further assessment as to their current energy consumption. This research used a survey to explore current user behaviour in residential buildings energy performance in the city of Jeddah, KSA. The findings of the survey showed: • The buildings thermal properties were found to be poorly designed • The majority of users within the buildings prefer a room temperature of below 24 °C, which requires a massive amount of cooling • Due to the climate conditions and the cultural aspects of KSA, housing units are occupied for more than 18 hours per day • An increase in user awareness has helped to slightly improve residential buildings energy efficiency Knowing the current high energy consumption sources and causes and being able to define available opportunities for further developments on building thermal properties enhancements and how to increase user awareness to reach self-sustaining buildings is essential.

The creation of a Europe-wide electricity market combined with the increased intermittency of supply from renewable sources calls for an investigation into the risk of aggregate peak demand. This paper makes use of a risk model to assess differences in time-use data from residential end-users in five different European electricity markets. Drawing on the Multinational Time-Use Survey database, it assesses risk in relation to the probability of electrical appliance use within households for five European countries. Findings highlight in which countries and for which activities the risk of aggregate peak demand is higher and link smart home solutions (automated load control, dynamic pricing and smart appliances) to different levels of peak demand risk.

Kiribati is a Pacific Island nation with a widely dispersed population and one of the highest rates of leprosy worldwide. Single dose rifampicin post exposure prophylaxis (SDR-PEP) of leprosy contacts has reduced new case detection rates in controlled trials. In 2018, a SDR-PEP programme was introduced in Kiribati that included screening and chemoprophylaxis of household contacts of leprosy cases both retrospectively (2010-2017) and prospectively (2018 onwards). We conducted a retrospective audit to determine comprehensiveness, timeliness and feasibility of the SDR-PEP programme. Overall, 13,643 household contacts were identified (9,791 in the retrospective and 3,850 in the prospective cohort). In the retrospective cohort, 1,044 (11%) contacts were absent, 403 (4%) were ineligible for SDR and 42 new cases were detected (0.4%) Overall SDR coverage was 84.7%. In the prospective cohort, 164 (4%) contacts were absent, 251 (7%) were ineligible for SDR and 23 new cases were diagnosed (0.6%). Overall, SDR coverage was 88.1%. Across both cohorts, there were a total of 23 SDR refusals. The median time to SDR ad-ministration was 220 days (IQR 162-468) and 120 days (IQR 36-283) for the retrospective and prospective cohorts respectively. SDR was readily accepted in both cohorts. The new case detec-tion rate (0.5%) is consistent with that seen in other studies. Overall SDR coverage in both the retrospective and prospective phases met programmatic expectations.

The aims of the study to analyze the influence of knowledge, attitude, education and gender of the head of the family for household preparedness against flood from Bengawan Solo River in Kedungdowo Village, Balen District of Bojonegoro Regency. The method used in this study is survey method. This study is explanatory observational research. Population studied is 85 head of families from Kedungdowo Village, Balen District, Bojonegoro Regency. The sampling method for collecting the data from the families is stratified random sampling. Data analysis methods used in this study are descriptive statistical analysis and logistic regression analysis with a 95% confidence level to identify the level of preparedness and the relationship between factors that affect preparedness. The findings shows that knowledge, attitude, education and gender significantly influence household preparedness against Bengawan Solo flood. Attitude is the most dominant variable that influenced household preparedness

The implementation of sustainable practices, such as the use of renewable sources and efficient technologies, is crucial for reducing climate change. Energy efficiency is highly important on a global scale due to its relationship with climate change, aiming to minimize environmental impact. In Spain, renewable energy policies have increased self-sufficiency and reduced the use of fossil fuels. Optimizing energy consumption in residences, buildings, and industries is essential for improving efficiency. This was taken into consideration for conducting this study, focusing on the residential sector. The desire to understand the level of energy efficiency in Extremadura drove this project, which focuses on collecting and analyzing data on a set of homes located in the au-tonomous community of Extremadura, with the purpose of evaluating their energy efficiency. To achieve this, a computer tool will be employed to provide a detailed view of the different levels of energy efficiency present in the community. In addition to data collection and analysis, research will be conducted to identify areas for improvement. This will allow proposing a series of specific measures that users can implement to optimize energy efficiency in their homes, adapting them to the particular characteristics of each residence.

Evolutionary psychology theories propose that contact with green, natural environments may benefit physical health, but little comparable evidence exists for brown, natural environments, such as the desert. In this study, we examined the association between “brownness” and “greenness” with fasting glucose among young residents of El Paso, Texas. We defined brownness as the surface not covered by vegetation or impervious land within Euclidian buffers around participants’ homes. Fasting glucose along with demographic and behavioral data was obtained from the Nurse Engagement and Wellness Study (N = 517). We found that residential proximity to brownness was not associated with fasting glucose when modeled independently. In contrast, we found that residential greenness was associated with decreased levels of fasting glucose, despite the relatively low levels of greenness within the predominantly desert environment of El Paso. A difference between the top and bottom greenness exposure quartiles within a 250 m buffer was associated with a 3.5 mg/dL decrease in fasting glucose levels (95% confidence interval: -6.2, -0.8). Our results suggest that within the understudied context of the desert, green vegetation may be health-promoting to a degree that is similar to other, non-desert locations in the world that have higher baselines levels of green.

DC residential distribution system (RDS) consisted by DC living home will be a significant integral part in the future green transmission. Meanwhile, the increasing number of distributed resources and intelligent devices will change the power flow between main grid and demand sides. The utilization of distributed generations (DGs) requires an economic operation, stability, environmentally friendly in the whole DC system. This paper not only presents an optimization schedule and transactive energy (TE) approach through centralized energy management system (CEMS), but a control approach to implement and ensure DG output voltages to various DC buses in DC RDS. Based on data collection, prediction and a certain objection, the expert system in CEMS can work out the optimization schedule, after this, the voltage droop control for steady voltage is aligned with the command of unit power schedule. In this work, a DC RDS is as a case study to demonstrate the process, the RDS is associated with unit economic models, cost minimization objective is proposed to achieve based on real-time electrical price. The results show that the proposed framework and methods will help the targeted DC residential system to reduce the total cost and reach stability and efficiency.

This paper critically reviews the correlation between the built environment and sociology as it pertains to residential segregation and social housing policy in Iran. The objective is to identify design strategies that minimize the risk of social isolation, promote social interaction, and foster a sense of community within affordable housing zones. The literature review includes existing research on urban segregation and social sustainability, with a focus on architectural solutions. Case studies are utilized to exemplify both positive and negative social outcomes related to urban segregation and identify effective design elements. The findings highlight the complex nature of residential segregation and its impact on social isolation, social capital, and social exclusion. The built environment contributes to the problem by facilitating the creation of isolated communities, and architects have a crucial role in addressing them. The results suggest that a comprehensive social housing policy is necessary to improve the quality of social housing and reduce residential segregation in Iran. Finally, the paper provides practical design strategies to promote social interaction, enhance accessibility and mobility, create mixed-use developments, and incorporate sustainable design features in social housing policy. By using design strategies that support social sustainability and inclusiveness, architects can create thriving and sustainable urban environments that prioritize the needs of marginalized communities.

We estimated the daily intakes of chlorpyrifos and cypermethrin via ingestion of indoor dust and outdoor soils using the Stochastic Human Exposure and Dose Simulation Model on a probabilistic approach for Taiwan’s homes. Variable information for the daily intake estimation, such as concentration, ingestion rate, body weight, was adopted from previous studies. Monte Carlo simulation was performed with 1,000,000 iterations to simulate a single daily intake, which was shown in terms of percentage of the Acceptable Daily Intake (ADI) of either insecticide. The daily intakes were minimal with a 99% probability; at 99.9th percentile, however, the total intakes leaped to 13.1% and 20.0% of the respective ADIs of chlorpyrifos and cypermethrin. The sensitivity analysis indicated that concentration was the most determinant variable. Compared to the data of daily intakes via dietary ingestion of vegetables derived from a previous study, the estimated intakes by this study were considerable at the highest percentile, which referred to insecticide residues few days after insecticide application. Consequently, the non-dietary ingestion exposure to either insecticide was negligible in most cases; nevertheless, for those with indoor insecticide applications, the daily intakes for young children could be of concern. Frequently home cleaning is recommended to reduce the exposure.

Food insecurity is a multidimensional concept adequately challenging not only the complex operationalization effort but also judgments of who is food secure and who is not. This study aimed to assess the level of household food insecurity in the study area. Both probability and non-probability sampling procedures were employed to draw the 367 respondents, key informants, and focus group discussants. The Consolidated Approach for Reportig Indicators (CARI) console model was constructed with four indicators: Food consumption score, Food energy shortfall, Food expenditure share, and Livelihood asset depletion. Descriptive statistics was used to analyze data in the models. The CARI result revealed that 41.1%, 9.3%, 20.4% and 29.2% of households were food secure, marginally food secure, moderately food insecure and severely food insecure, respectively. The overall prevalence showed that 49.6% households were food insecure and 50.4% were food secure. Moreover, female-headed households and households living the Belg and CHV livelihood zones were more food insecure than their counterparts. The study concluded that the problem of food insecurity is pervasive in the study area in general and Belg and CHV livelihood zones, in particular. Therefore, more attention and intervention should be given by policymakers and concerned development partners to alleviate the problem.

Target 12.3 of the United Nations Sustainable Development Goals (SDGs) calls for halving per capita global food waste at the retail and consumer levels, by 2030. The Food Waste Index is suggested as a methodology for grasping the situation. This paper focuses on the consumer level (household food waste). We argue that in order for generating useful information for devising and implementing effective measures for reducing food waste, it should be measured at Level 3 of the Food Waste Index, based on sorting analysis of generated waste, making a distinction between avoidable and non-avoidable food waste. Furthermore, a breakdown by sub-categories that reflect the flow of food in the household could help identify target behaviours. We have developed a categorisation scheme that is internationally agreeable and adoptable, and 1) generates useful information for policy-making and for tackling with reduction of food waste, 2) makes clear the concept of avoidable food waste, and 3) is practical and does not overcomplicate the work of grasping the situation of food wastage. Results of workshops regarding this scheme suggest that the scheme satisfies the criteria. This scheme has been applied to a few sorting analyses of household food waste in Japan, and their results are compared.

We analyzed the characteristics of the Severe Acute Respiratory Syndrome Coronavirus-2 (SARS-CoV-2) infected children during lock-down period in Catalonia (Spain), and their transmission role within the households. Among 295 traced household contacts of 89 pediatric patients, children were classified as final index cases in only 3.4% of the traced homes.

Smallholder farmers in Ethiopia face increasing challenges from climate change and variability, which threaten their food security and livelihoods. This study examines how adopting single and combined climate change adaptation practices affects their vulnerability to food insecurity in Bench Maji Zone, southwest Ethiopia. Through multistage sampling, data was gathered from 390 rural households in four climate-prone districts. The study examines the impacts resulting from both individual and combined implementations of adaptation techniques. These techniques encompass crop management practices, soil and water conservation measures, and livelihood portfolio diversification strategies. The study employed the multinomial endogenous treatment effect regression model to address selection bias and endogeneity resulting from various sources of heterogeneity, whether observed or unobserved. The results show that farmers who adopted adaptation practices were less vulnerable to food insecurity than those who did not. The study also finds that adopting multiple practices has a more significant impact than adopting single practices. Our findings suggest that implementing climate change adaptation strategies can increase the resilience of smallholder farmers in the study area and decrease their vulnerability to food insecurity. The study recommends supporting farmers in adopting these strategies through research and development, information dissemination, and collaborations among farmers, researchers, and extension services.

The reduction of PV prices and interest in energy independence accelerate the adoption of residential battery storage. This storage can support various functions of an energy system undergoing decarbonization. In this work, operative benefits of the storage from the system perspective, namely, generation cost reduction and congestion mitigation, are investigated. Germany is chosen as a case study due to its strong reliance on variable renewable energy. For the analysis, an economic dispatch model with a high spatial resolution is coupled with a Pan-European transmission grid model. It is shown that the system's generation costs are highest when the assets are used only to maximize the PV self-consumption, and the costs are lowest when the storage also reacts to the market dynamics. This amounts to 6% cost reduction. Both operation strategies result in an equal level of grid congestion and infrastructure loading. This is improved with a strategy that accounts regional peak reduction as a secondary objective. The high congestion level emphasizes the grid expansion need to keep pace with the generation and electrification expansion necessary to decarbonize other sectors. Lastly, policymakers should enable multipurpose utilization, e.g., via the introduction of market-oriented retail electricity prices with intervention options for grid operators.

1960s Europe saw a large number of residential neighborhoods built to house those migrating from the countryside. Today, more than 50 years later, these neighborhoods suffer high levels of functional, social, and technical obsolescence. In response to this, University of Seville developed the Aura Strategy as an intervention methodology to find global solutions to issues in outdated neighborhoods. To provide visibility to this aspect of the Aura strategy, the retrofit proposal presented in this article provides a solution to improve the roofing of buildings in a case study neighborhood (Polígono de San Pablo, Seville) and an analysis of the results in terms of energy and financial savings for local residents. The results show that for a population of roughly 18,000 (in 2018), net savings, including energy and retrofitting costs, ranging from nearly 6.5 to over 8.6 million can be made over the 20-year life cycle span. Likewise, the results obtained on the reduction of thermal loads indicate a 72% decrease in energy consumption, equivalent to a saving of close to 4,500 tons of greenhouse gas emissions for the district and the entire life cycle time period, with the consequent benefits on the impact on air quality and and the fight against climate change. climate change.

The main objective of this study is to apply structural equation modeling with partial least squares and based on covariance to assess the satisfaction of residential electricity consumers. The methodology used compares the results of both structural equation models to indicate the model that best fits the problem of measuring the satisfaction of residential consumers of electricity concessionaires and licensees. The sample used in the survey contained questionnaire responses from 86.175 individuals considering the period from 2014 to 2018. The constructs evaluated were satisfaction, quality, value, loyalty, and trust. Confidence interval analysis shows that all weights are significant, demonstrating the importance of all the indicators that represent the constructs. The trust, quality, and value constructs can explain 74.4% of the variability of the satisfaction construct, so the explanatory capacity of this relationship is considered substantial. Finally, the evaluation of the performance of the service provided by the electric energy concessionaires/licensees, measured by customer satisfaction, allows for the continuous improvement of services and meeting, even if minimally, the expectations of its consumers.

The importance of this study may be defined by using the smart techniques to earned value indicators of residential buildings projects in Republic of Iraq, only one development intelligent forecasting model was presented to predict Schedule Performance Index (SPI), Cost Performance Index (CPI), and To Complete Cost Performance Indicator (TCPI) are defined as the dependent. The approach is principally influenced by the determining numerous factors which effect on the earned value management, that involves Iraqi historical data. In addition, six independent variables (F1: BAC, Budget at Completion., F2: AC, Actual Cost., F3, A%, Actual Percentage., F4: EV, Earned Value. F5: P%, Planning Percentage., and F6: PV, Planning Value) were arbitrarily designated and satisfactorily described for per construction project. It was found that ANN has the capability to envisage the dust storm with a great accuracy. The correlation coefficient (R) has been 90.00%, and typical accuracy percentage has been 89.00%.

Land use is an embodiment of human socioeconomic activities and represents a bridge between these activities and natural systems. Through social activities, humans transform land use to promote social and economic development and improve production, living conditions, and eco-logical functions of land. Rural residential land represents a space for rural residents to reside in and exhibits spatial characteristics that evolve over time, which is proof of rural socioeconomic development. This paper observes rural residential land in 21 cities on the Grand Canal and analyses its spatial differentiation. Then, it explores the driving factors of this land using spatial grid analysis and the geographic detector model. Lastly, it proposes three different forms of rural residential land based on the results. The study found that: (1) the change of rural residential land in the northern part of the Grand Canal was more volatile than that in the southern part. The change of rural residential land from 1990 to 2020 conformed to the pattern of cultivated land - rural residential land - urban construction land; (2) Based on the driving factors of rural residen-tial land, the land is divided into one-dimensional cities, two-dimensional cities and three-dimensional cities. Circular, linear, and scattered cities of different sizes were affected by socioeconomic factors, transportation accessibility, and the natural environment, respectively; and (3) Finally, according to the spatial differentiation characteristics and the driving factors of rural residential land, the study proposes the construction of three types of villages through the strate-gies of constructing large-scale villages, relocating and reconstructing new villages, and con-structing high-quality villages, respectively. Enhancing the scientific planning of rural residential land and its efficiency can offer the protection of agricultural land and the integration of urban and rural areas in the new era.

Surveillance is the systematic data collection, analysis, and interpretation essential to planning and implementing control activities. The lack of success in control and surveillance elsewhere for the Ae. aegypti mosquito demands developing new accessible and effective strategies. This work aimed to develop and evaluate an adhesive and lure trap for household indoor and outdoor surveillance of Ae. aegypti. Based on a bibliographic review, four compounds with significant attraction percentages for Ae. aegypti were considered. Our more effective blend was determined by preliminary bioassays using the high-throughput screening system (HITSS) and 90 × 90 cm mosquito cages. We designed a low-cost, pyramid-shaped, sticky cardboard trap to incorporate the selected blend. Semi-field 2 x 2 m cages and field tests were conducted to evaluate its effectiveness through mosquito capture percentages. In laboratory tests, blend number 2 presented an attraction percentage of 47.5 ± 4.8%; while in semi-field cages, a 4-inch, 110-v powered fan was used to disperse the attractants, then a similar capture percentage of 43.2 ± 4.0 % was recorded. Field evaluation of the at-house indoor environment and comparing it with the golden standard BG-Sentinel trap recorded interesting results, i.e., an average of our prototype 6.0 ± 1.5 trapped mosquitoes versus 10.0 ± 2.6. In most Latin American countries, there is a lack of formal and accessible strategies for monitoring adult populations of Ae. aegypti, therefore, must develop tools that reinforce entomological surveillance methods.

The objective of the study was to report the health-related quality of life (HRQOL) following road traffic accidents (RTAs) among children. A community-based survey using EuroQol five-dimension questionnaire (EQ-5D-5L) in Hindi was used to collected data from community. The survey included 2620 households from urban and rural areas of Ujjain, India. From these households 229 children aged 5–18 years with a history of RTA in the last 1 year were identified, with 27%, 63%, and 10% children reporting mild, moderate, and severe injury based on length of hospitalization. Motorcycles, bicycles, and pedestrians constituted most RTAs. Helmet use was low (12%). EQ-5D-5L revealed that the most severe and extreme problem was pain and discomfort, whereas the least severe problem was usual activity and self-care. The most common (65%) injuries were either abrasion or fracture and dislocation. EQ-5D-5L severity index was maximum (mean 72) for lower extremity injuries. The results of the present study highlight the ability and requirement for quality of life measurement using EQ-5D-5L among children post-RTA.

The increasing residential space differentiation is an important practical problem for Chinese cities. The different choice of living space for urban residents is a concrete reflection of social class divide, which reflects the differences in the choices and demands of different social groups for urban housing. Taking Wuhan, an important city in central China, as an example, this research divides the residential space based on the social resource structure, and analyzes and compares the spatial differentiation and influencing factors of different residential areas and houses with different prices in Wuhan by spatial differentiation indicators and geographic detector. The results show clear differences in resource structure among residential areas, and there are few high-quality residential areas with a concentrated distribution. The spatial differentiation levels of different residential areas are distinct, and the pursuit of high-quality and scarce resources is the key to the residential space differentiation of most large cities in China. In addition, residential space differentiation can lead to inter-generational problems such as housing wealth inequality, resource deprivation and solidified class identity. Exploring the mechanisms and social effect of residential space differentiation in most large cities in China can provide some reference for China's urban space planning and real estate market regulation in the new era.

A humidity-sensitive demand-controlled ventilation system is known for many years. It has been developed and commonly applied in regions with an oceanic climate. Some attempts were made to introduce this solution in Poland in a much severe continental climate. The article evaluates this system's performance and energy consumption applied in an 8-floor multi-unit residential building, virtual reference building described by the National Energy Conservation Agency NAPE, Poland. The simulations using the computer program CONTAM were performed for the whole hating season for Warsaw's climate. Besides passive stack ventilation that worked as a reference, two versions of humidity-sensitive demand-controlled ventilation were checked. The difference between them lies in applying the additional roof fans that convert the system to hybrid. The study confirmed that the application of demand-controlled ventilation in multi-unit residential buildings in a continental climate with warm summer (Dfb) leads to significant energy savings. However, the efforts to ensure acceptable indoor air quality require hybrid ventilation, which reduces the energy benefits. It is especially visible when primary energy use is analyzed.