Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Glaucoma is a multifactorial neurodegenerative disease, characterized by degeneration of the retinal ganglion cells (RGCs). There has been little progress in developing efficient strategies for neuroprotection in glaucoma. We profiled the retina transcriptome of Lister Hooded rats at 2 weeks after optic nerve crush (ONC) and analyzed the data from the Genomic Fabric Paradigm (GFP) to bring additional insights into the molecular mechanisms of the retinal remodeling after induction of RGC degeneration. GFP considers for the expression of each gene 3 independent characteristics: level, variability and correlation with each other gene. Thus, the 17,657 quantified genes our study generated a total of 155,911,310 values to analyze. This represents 8,830x more data per condition than a traditional transcriptomic analysis. ONC led to a 57% reduction in RGC numbers as detected by retrograde labeling with DiI. We observed a higher Relative Expression Variability after ONC. Gene expression stability was used as a measure of transcription control and disclosed a robust reduction in the number of very stably expressed genes. Predicted Protein-Protein interaction (PPI) analysis with STRING revealed axon and neuron projection as mostly decreased processes, consistent with RGC degeneration. Conversely, immune response PPIs were found among up-regulated genes. Enrichment analysis showed that Complement Cascade and Notch Signaling Pathway, as well as Oxidative Stress and Kit Receptor Pathway were affected after ONC. To expand our studies of altered molecular pathways, we examined the pair-wise coordination of gene expressions within each pathway and within the entire transcriptome using Pearson correlations. ONC increased the number of synergistically coordinated pairs of genes and the number of similar profiles mainly in Complement Cascade and Notch Signaling Pathway. This deep bioinformatic study provides novel insights beyond the regulation of individual gene expression and discloses changes in the control of expression of Complement Cascade and Notch Signaling functional pathways that may be relevant for both RGC degeneration and remodeling of the retinal tissue after ONC.

The aim of this review was to provide an update on the potential of cell therapies to restore or replace damaged and/or lost cells in retinal degenerative and optic nerve diseases, describing the available cell sources and the challenges involved in such treatments when these techniques are applied in real clinical practice. Sources include human fetal retinal stem cells, allogenic cadaveric human cells, adult hippocampal neural stem cells, human CNS stem cells, ciliary pigmented epithelial cells, limbal stem cells, retinal progenitor cells (RPCs), human pluripotent stem cells (PSCs) (including both human embryonic stem cells (ESCs) and human induced pluripotent stem cells (iPSCs)) and mesenchymal stem cells (MSCs). Of these, RPCs, PSCs and MSCs have already entered early-stage clinical trials since they can all differentiate into RPE, photoreceptors or ganglion cells, and have demonstrated safety, while showing some indicators of efficacy. Stem/progenitor cell therapies for retinal diseases still have some drawbacks, such as the inhibition of proliferation and/or differentiation in vitro (with the exception of RPE) and the limited long-term survival and functioning of grafts in vivo. Some other issues remain to be solved concerning the clinical translation of cell-based therapy, including (1) the ability to enrich for specific retinal subtypes; (2) cell survival; (3) cell delivery, which may need to incorporate a scaffold to induce correct cell polarization, which increases the size of the retinotomy in surgery and, therefore, the chance of severe complications; (4) the need to induce retinal detachment to perform the subretinal placement of the transplanted cell; and (5) the evaluation of the risk of tumor formation caused by the undifferentiated stem cells and prolific progenitor cells. Despite these challenges, stem/progenitor cells represent the most promising strategy for retinal and optic nerve disease treatment in the near future, and therapeutics assisted by gene techniques, neuroprotective compounds and artificial devices can be applied to fulfil clinical needs.

Sterol homeostasis in mammalian cells and tissues involves balancing three fundamental processes: de novo sterol biosynthesis; sterol import (e.g., from blood-borne lipoproteins); and sterol export. In complex tissues, composed of multiple different cell types (such as the retina), import and export also may involve intra-tissue, inter-cellular sterol exchange. Disruption of any of these processes can result in pathologies that impact the normal structure and function of the retina. Here, we provide a brief overview of what is known currently about sterol homeostasis in the vertebrate retina and offer a proposed path for future experimental work to further our understanding of these processes, with relevance to the development of novel therapeutic interventions for human diseases involving defective sterol homeostasis.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

Aim: To investigate the effects of intensive physical exercise on retinal microvascular regulation in healthy volunteers by the adaptive optics retinal camera measurement. Methods: We included healthy volunteers (11 men and 14 women) aged 20.6± 0.9. Heart rate (HR) and systolic and diastolic blood pressure (SBP, DBP) were recorded before and after a submaximal physical exertion of continuously riding a training ergometer. The superior temporal retinal artery measurements were captured using the adaptive optics (AO) camera rtx1TM (Imagine Eyes, Orsay, France) without pupil dilatation. We compared measures of vessel diameter (VD), lumen diameter (LD), two walls (Wall 1, 2), wall-to-lumen ratio (WLR), and wall cross-sectional analysis (WCSA) before and immediately after the cessation of exercise. Results: Cardiovascular parameters: After exercise, SBP, DBP and HR changed significantly from 130.2±13.2 to 159.7±15.6 mm Hg, 81.2±6.3 to 77.1±8.2 mm Hg and 80.8±16.1 to 175.0±6.2 bpm, respectively (p < 0.002). Retinal microcirculation analysis: Before the exercise, the mean LD was 96.0±6.8, VD 118.5±8.3, WLR 0.234±0.02, WCSA 3802.8±577.6. The mean LD and Wall 1 did not change significantly after exercise but slightly decreased. The VD, Wall 2, WLR and WCSA decreased significantly (p

The study presents the synthesis and characterization of dual-layer sulfonated polyphenylenesulfone (SPPSu) nanocomposite hollow fiber nanofiltration membranes incorporating titanium dioxide (TiO2) nanoparticles using the phase inversion technique. The newly developed membranes were systematically characterized using advanced tools and methods to evaluate their properties and performance. The study focused on investigating the effects of TiO2 addition in the SPPSu inner layer on pure water permeability, and salt rejection. The nanocomposite hollow fiber nanofiltration membranes exhibited a significant enhancement in pure water permeability, with a three-fold increase compared to the pristine membranes, achieving a flux of 5.4 L/m2h.bar. The addition of TiO2 also led to an improvement in the mechanical properties of the membranes, as evidenced by the increase in the expected tensile strength from 2.4 to 3.9 MPa. To evaluate the salt rejection performance, rejection tests were conducted using a laboratory-scale filtration setup in recycle mode. Aqueous solutions containing different divalent ions, specifically magnesium sulfate (Mg2SO4) and sodium sulfate (Na2SO4) at a concentration of 500 ppm, were used as the feed solution. The modified dual-layer hollow fiber nanocomposite membranes exhibited a maximal rejection of 95% for Mg2SO4, demonstrating their effective separation capabilities for divalent ions. The findings of this study highlight the successful synthesis and characterization of dual-layer SPPSu nanocomposite hollow fiber nanofiltration membranes incorporating TiO2 nanoparticles. The incorporation of TiO2 resulted in improved pure water flux, mechanical strength, and salt rejection performance. These enhanced properties make the developed nanocomposite membranes promising candidates for applications in nanofiltration processes, particularly for the selective separation of divalent ions from aqueous solutions.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Chronic inflammatory diseases are considered the most significant cause of death worldwide. Current treatments for inflammatory diseases are limited due to the lack of understanding of the biological factors involved in early-stage disease progression. Nerve growth factor (NGF) is a neurotrophic factor directly associated with inflammatory and autoimmune diseases like osteoarthritis, multiple sclerosis, and rheumatoid arthritis. It has been shown that NGF levels are significantly upregulated at the site of inflammation and play a crucial role in developing a robust inflammatory response. However, little is known about NGF's temporal expression profile during the initial progressive phase of inflammation. This study aimed to determine the temporal expression pattern of NGF in rat skin during Adjuvant-Induced Arthritis (AIA). Sprague Dawley rats were randomly divided into control and Complete Freund's Adjuvant (CFA) treated groups. Levels of NGF were evaluated following unilateral AIA at different time points and it was found that peripheral inflammation due to AIA significantly upregulated the expression of NGF mRNA and Protein in a biphasic pattern. These results suggest that NGF signaling is crucial for initiating and maintaining peripheral neurogenic inflammation in rats during AIA.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

The vertebrate skeletal neuromuscular junction (NMJ) has long served as a model system for studying synapse structure, function and development. Over the last several decades a neuron-specific isoform of agrin, a heparan sulfate proteoglycan, has been identified as playing a central role in synapse formation at all vertebrate skeletal neuromuscular synapses. While agrin was initially postulated to be the inductive molecule that initiates synaptogenesis, this model has been modified in response to work showing that postsynaptic differentiation can develop in the absence of innervation, and that synapses can form in transgenic mice in which the agrin gene is ablated. In place of a unitary mechanism for neuromuscular synapse formation, studies in both mice and zebrafish have led to the proposal that two mechanisms mediate synaptogenesis, with some synapses being induced by nerve contact while others involve the incorporation of prepatterned postsynaptic structures. Moreover, the current model also proposes that agrin can serve two functions, to induce synaptogenesis and to stabilize new synapses, once these are formed. This review examines the evidence for these propositions, and concludes that it remains possible that a single molecular mechanism mediates synaptogenesis at all NMJs, and that agrin acts as a stabilizer, while its role as inducer is open to question. Moreover, if agrin does not act to initiate synaptogenesis, it follows that as yet uncharacterized molecular interactions are required to play this essential inductive role. Several alternatives to agrin for this function are suggested, including focal pericellular proteolysis and integrin signaling, but all require experimental validation.

Aim: the main aim of this study is to compare the onset of effectiveness of mental nerve block with lingual infiltration and inferior alveolar nerve block on patients visiting dental hospital for extraction of mandibular anterior teeth. Materials and methods: The study was set in a clinical setting. This was a randomized controlled double-blind cross study, where 25 subjects received two treatments at an interval of at least 1 week in a within a dental hospital.Inferior alveolar nerve block and lingual nerve block injection is given with 2mL lignocaine 2% with 1:2,00,000 epinephrine was administered for the right side. Mental nerve block along with lingual infiltration of the corresponding tooth was given with 2mL lignocaine 2% with 1:2,00,000 epinephrine was administered on the left side.Visual analogue scale (VAS) was used in this study, which consists of a scale with range of 0-10 pain severity on which 0 indicated absence of pain and 10 the worst pain possible. The patients were asked to give scores corresponding to his/her pain, after IANB, mental nerve block and lingual infiltration and these scores were recorde.Results: From the results we can see that patients gave scores between 3-4, stating that they had moderate pain during extraction after administration of IANB (54%) (graph 2) and VAS scores of 0-1 were given by patients, which is suggestive of no pain during extraction after administration of Mental nerve block and lingual nerve infiltration (62%)Conclusion: Within the limits of the study we can conclude that mental nerve block along with lingual infiltration is an effective way to completely and quickly anaesthetise the central incisor to the 1st premolar region.

Glaucomatous optic neuropathy, a major cause of blindness, is characterized by the loss of retinal gan-glion cells (RGCs) and degeneration of their axons. Mitochondria are deeply involved in maintaining RGCs and their axons. Therefore, lots of attempts have been made to develop diagnostic tools and therapies tar-geting mitochondria. Recently, we reported that mitochondria are uniformly distributed in unmyelinated axons of RGCs, possibly owing to the ATP gradient. Thus, using transgenic mice expressing yellow fluo-rescent protein targeting mitochondria exclusively in RGCs within the retina, we assessed the alteration of mitochondrial distributions induced by optic nerve crush (ONC) via in vitro flat-mount retinal sections and in vivo fundus images captured through the cornea with a confocal scanning ophthalmoscope. We observed that the mitochondrial distribution in unmyelinated axons of RGCs that survived the ONC remained uni-form, although their density increased. Furthermore, via in vitro analysis, we discovered that the mitochon-drial size is attenuated following ONC. These results suggest that ONC induces mitochondrial fission without disrupting the uniform mitochondrial distribution. This mechanism may help to prevent axonal degeneration and apoptosis. The in vivo visualization system of axonal mitochondria in RGCs may be ap-plicable in the diagnosis of progression of optic neuropathy.

This study aimed to evaluate the effectiveness of decellularized nerves for promoting nerve regeneration by transplanting them from the sciatic nerve of a rabbit to that of a rat. The Sciatic nerves were harvested from New Zealand White Rabbits (n=4). A 1-cm segment of each nerve was decellularized by Sondell’s protocol and preserved at –4℃ in Roswell Park Memorial Institute (RPMI) 1640 medium for one week. Subsequently, a defect of a similar size was created in the sciatic nerves of rats. The decellularized nerves treated with detergent were then transplanted into these defects in the rats. The study included the three following groups: Group 1 (n=4) was the decellularized xenogeneic nerve group; Group 2 (n=7) was the negative control group in which the defect remained un-repaired; and Group 3 (n=5) was composed of the positive control group where the nerve was immediately transplanted from one rat to another. The sciatic functional index (SFI) was considered to evaluate the motor function by comparing it with the normal side at 1, 2, 3, and 4 weeks, and 1, 2, and 3 months postoperatively. Furthermore, electrophysiological and immunohistochemical assessments were conducted at 4 months. Immunohistochemically, at 16 weeks postoperative, the experimental group did not show statistically significant differences compared to controls in terms of schwann cell comparison, yet exhibited favorable outcomes when compared to the positive control group. Additionally, analysis of motor function test confirmed recovery of latency and nerve conduction velocity to levels similar to those of the normal side. While the nerve allograft demonstrated superior nerve regeneration in motor function test at 3 months, markedly low values were observed in all groups. When reconstructing peripheral nerves using detergent-based decellularized xenogenic nerves, analysis of immuno-histochemistry and motor nerve conduction study reveals a promising degree of nerve regeneration. However, when compared with fresh allograft group at 3 months after operation, the sciatic functional index was lower. Significantly lower values observed across all groups compared to previous assessments indicate the need for further research into potentially influential alternative factors.Histologically, at 16 weeks postoperative, the experimentally treated group did not show statistically significant differences compared to the controls in terms of a Schwann cell comparison, but exhibited favorable outcomes when compared to the positive control group. Additionally, an analysis of the motor function testing confirmed recovery of the latency and nerve conduction velocity to levels similar to those of the normal side. While the nerve allograft demonstrated superior nerve regeneration in the motor nerve examination at 3 months, notably low values were observed in all the groups. When reconstructing the peripheral nerves using detergent-based decellularized xenogeneic nerves, an analysis of immunohistochemistry and motor nerve conduction study reveals a promising degree of nerve regeneration. However, when compared with the fresh allograft group at 3 months post-operation, the sciatic functional index was lower. The significantly lower values observed across all groups compared to those of the previous assessments indicate the need for further research of potentially influential alternative factors.

Peripheral nerve injuries (PNI) can have several etiologies, such as trauma and iatrogenic interventions that can lead to the loss of structure and/or function impairment. These changes can cause a partial or complete loss of motor and sensory functions, physical disability, and neuropathic pain, what in turn can affect the quality of life. For those reasons, PNI is a major public health concern. This review aims to revisit the concepts associated with the PNI. First, the anatomy of the peripheral nerve is detailed to explain the different types of injury. Then, some of the available therapeutic strategies are explained, including surgical methods, pharmacological therapies, and the use of cell-based therapies alone or in combination with biomaterials in the form of tube guides. Nevertheless, even with the various available treatments, it is difficult to achieve a perfect outcome with complete functional recovery. This review aims to explain the urge for new approaches and to understand the methods to evaluate nerve regeneration in a One Health perspective. In vitro models followed by in vivo models are very important to be able to translate the achievements to human medicine.

Objective: There are currently no known treatment methods for ensuring complete recovery from facial nerve damage. Thus, various basic and clinical studies continue to be conducted to achieve this end. As part of this research, autophagy is being investigated for its role in nerve regeneration. Here, we review the existing literature regarding the involvement and signifi-cance of autophagy in facial nerve injury and regeneration. Methods: A comprehensive litera-ture review was conducted to assess the induction and role of autophagy in facial nerve injury and subsequent regeneration. Results: Studies conducted on rats and mice have demonstrated activation of autophagy and expression of related factors in facial and sciatic nerves. Among the most studied of these factors in relation to degeneration and regeneration of facial and sciatic nerves are LC3II/I, PI3K, mTOR, Beclin-1, ATG3, ATG5, ATG7, ATG9, and ATG12. Conclusion: This analysis indicates that autophagy is involved in the process of nerve regeneration follow-ing facial and sciatic nerve damage. Inadequate autophagy induction or failure of autophagy re-sponses can result in regeneration issues after facial or sciatic nerve damage. Animal studies suggest that autophagy plays an important role in facial and sciatic nerve degeneration and re-generation.

Vascular anomalies are a diverse group of abnormal blood vessel developments that can occur at birth or shortly afterward. Embolization and sclerotherapy have been utilized as a treatment option for these malformations but may cause moderate to severe pain. This study aims to evaluate the utilization of peripheral nerve blocks in opioid consumption, pain scores, and length of stay. A retrospective chart review was conducted at the UPMC Children's Hospital of Pittsburgh for all patients who underwent embolization and sclerotherapy between 2011 and 2020. Patient data was collected to compare opioid consumption, pain scores, and length of stay. Eight hundred fifty-four procedures were performed on 347 patients. The morphine milligram equivalent per kilogram mean ratio between groups was 0.9 (0.86, 0.95) with a p-value of &lt;0.001. The pain score mean ratio was –1.17 (–2.2, -0.1) and a p-value of 0.027. Length of stay had a mean ratio of 0.94 (0.4, 2) and a p-value of 0.875. By decreasing opioid consumption and postoperative pain scores, peripheral nerve blocks may have utility in patients undergoing embolization and sclerotherapy while not clinically increasing the length of stay for patients. Their use should be individualized and carefully discussed with the interventional radiologist.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

The porous structure is an important three-dimensional morphological feature of the peripheral nerve guidance conduit (NGC), which permits infiltration of cells, nutrients, and molecular signals, and the discharge of metabolic waste. Porous structures with precisely customised pore sizes, porosities, and connectivities were used to construct fully permeable, semi-permeable, and asymmetric peripheral NGCs to replace traditional nerve autografts in treatment of long-segment peripheral nerve injury. In this review, the features of porous structures and classification of NGCs based on these characteristics are discussed. Common methods for constructing 3D porous NGCs in current research are described, as well as the pore characteristics and the parameters used to tune the pores. The effects of the porous structure on the physical properties of NGCs including biodegradation, mechanical performance, and permeability were analysed. Pore structure affects the biological behaviour of Schwann cells, macrophages, fibroblasts, and vascular endothelial cells during peripheral nerve regeneration. Construction of ideal porous structures is a significant advancement in the regeneration of peripheral nerve tissue engineering materials. The purpose of this review is to generalise, summarise, and analyse the preparation methods for porous NGCs and their biological functions in promoting peripheral nerve regeneration to guide development of medical nerve repair materials.

Voltage-gated Ca²⁺ (Ca_v) channels play pivotal roles in regulating gene transcription, neuronal excitability, and neurotransmitter release. In order to meet the spatial and temporal demands of visual signaling, Ca_v channels exhibit unusual properties in the retina compared to their counterparts in other areas of the nervous system. Here, we review current concepts regarding the specific subtypes of Ca_v channels expressed in the retina, their intrinsic properties and forms of modulation, and how their dysregulation could lead to retinal disease.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

Objectives: This study aims to explore the use of murine models in peripheral nerve transection research, evaluating and synthesizing key methods for analyzing nerve regeneration to guide future research and clinical interventions. Methodology: A systematic review was conducted in February 2024, adhering to Cochrane and PRISMA 2020 guidelines, using Medline, Scielo, and Lilacs databases. The focus was on experimental studies of nerve regeneration in animal models post-transection. Only experimental clinical trials reporting nerve regeneration outcomes were included; studies lacking a comparator group or functional evaluation methods were excluded. Results: Out of 273 studies initially identified from MEDLINE, 19 were selected for detailed analysis. The average study included 32.5 subjects, with about 10.16 subjects per intervention subgroup. The predominant model was the sciatic nerve injury with a 10mm gap. The most common intervention involved unprocessed adipose-derived stem cells, utilized in 14 articles. Conclusions: The review underscores the significant potential of current methodologies in peripheral nerve regeneration, particularly highlighting the use of murine models and thorough evaluation techniques. These studies significantly contribute to our understanding of nerve regeneration processes and inform directions for future research.

(1) Background: Neurologic and musculoskeletal diseases represent a considerable portion of the underlying etiologies responsible for the widely prevalent symptoms of pain, weakens, numbness, and paresthesia. Because of the subjective and often nonspecific nature of these symptoms, different diagnostic modalities have been explored and utilized.; (2) Methods: Literature review; (3) Results: Nerve and muscle biopsy remains the gold standard for diagnosing many of the responsible neurological and musculoskeletal conditions. However, the need for invasive tissue sampling is diminishing as more investigations explore alternative diagnostic modalities. Because of this, it is important to explore the current role of neurosurgical intervention for nerve and muscle biopsies and its current relevance in the diagnostic landscape of neurological and musculoskeletal disorders. With consideration of the role of nerve and muscle biopsy, it is also important to explore innovations and emerging techniques for conducting these procedures. This review explores the indications and emerging techniques for neurological intervention for nerve and muscle biopsies; (4) Conclusions: The role of neurosurgical intervention for nerve and muscle biopsy remains relevant in diagnosing many neurological and musculoskeletal disorders. Biopsy is especially relevant as a supportive point of evidence for diagnosis in atypical cases. Additionally, emerging techniques have been explored to guide diagnostics and biopsy, conduct less invasive biopsies, and reduce risks of worsening neurologic function and other symptoms secondary to biopsy.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Thousands of people worldwide suffer from injuries in the peripheral nerve and deal daily with the resulting physiological and functional deficits. Recent advances in this field are still insufficient to guarantee effective outcomes, and the development of new and effective therapeutic options requires the use of valid preclinical models that effectively replicate the characteristics and challenges associated with these injuries in humans. In this study, we established a sheep model for common peroneal nerve injuries that can be applied in preclinical research with the advantages associated with the use of large animal models. In an integrative way, this article includes a detailed description of the anatomy and functionality of the peripheral nerves of sheep’s hind limb, the surgical protocol for accessing the common peroneal nerve, the induction of different types of nerve damage and the application of possible therapeutic options. A neurological exam protocol directed to the common peroneal nerve was also established, allowing to identify the changes and deficits related with the nerve injury and to evaluate the functional progression over time. Finally, a preliminary stereological study was carried out to establish control values for the healthy peroneal common nerves of this model and to identify preliminary differences between therapeutic methods. The ultimate goal is to demonstrate that sheep is a valid model of peripheral nerve injury to be used in pre-clinical and translational works and to evaluate the efficacy and safety of nerve injury therapeutic options before its clinical application in human and veterinary patients.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

The study of the development of the vertebrate retina can be addressed from several perspectives: from purely qualitative to a more quantitative approach that takes into account its spatiotemporal features, its three dimensional structure and also the regulation and properties at the systems level. Here we review the ongoing transition towards a full four-dimensional characterization of the developing vertebrate retina, focusing on the challenges at the experimental, image acquisition, image processing and quantification. Using the developing zebrafish retina, we illustrate how quantitative data extracted from these type of highly dense three-dimensional tissues depends strongly on the image quality, image processing and algorithms used to segment and quantify. Therefore, we propose that the scientific community that focuses on developmental systems could strongly benefit from a more detailed disclosure of the tools and pipelines used to process and analyze images from biological samples.

The retina is a complex and fragile photosensitive part of the central nervous system which is prone to degenerative diseases leading to permanent vision loss. No proven treatment strategies exist to treat or reverse the degenerative conditions. Recent investigations demonstrate that cell transplantation therapies to replace the dysfunctional retinal pigment epithelial (RPE) cells and or the degenerating photoreceptors (PRs) are viable options to restore vision. Pluripotent stem cells, retinal progenitor cells and somatic stem cells are the main cell sources used for cell transplantation therapies. The success of retinal transplantation based on cell suspension injection is hindered by limited cell survival and lack of cellular integration. Recent advances in material science helped to develop strategies to grow cells as intact monolayers or as sheets on biomaterial scaffolds for transplantation into the eyes. Such implants are found to be more promising than the bolus injection approach. Tissue engineering techniques are specifically designed to construct biodegradable or non-degradable polymer scaffolds to grow cells as a monolayer and construct implantable grafts. The engineered cell construct along with the extracellular matrix formed, can hold the cells in place to enable easy survival, better integration and improved visual function. This article reviews the advances in the use of scaffolds for transplantation studies in animal models and its application in current clinical trials.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

Inherited retinal diseases (IRDs) are extremely heterogeneous with at least 350 causative genes, complicating the process of genetic diagnosis. We analyzed samples of 252 index cases with IRDs using the Blueprint Genetics panel for “Retinal Dystrophy” that includes 351 genes. The cause of disease could be identified in 55% of cases. A clear difference was obtained between newly-recruited cases (74% solved) and cases that were previously analyzed by panels or whole exome sequencing (26% solved). As for the mode of inheritance, 75% of solved cases were autosomal recessive (AR), 10% were X-linked, 8% were autosomal dominant, and 7% were mitochondrial. Interestingly, in 12% of solved cases, structural variants (SVs) were identified as the cause of disease. The most commonly identified genes were ABCA4, EYS and USH2A, and the most common mutations were MAK-c.1297_1298ins353 and FAM161A- c.1355_1356del. In line with our previous IRD carrier analysis, we identified heterozygous AR mutations that are not the cause of disease in 36% of cases. The studied IRD panel was found to be efficient in gene identification. Some variants were mis-interpreted by the pipeline and therefore multiple analysis tools are recommended to obtain more accurate annotation of potential disease-causing variant.

Diabetes is a prevalent global health issue associated with significant morbidity and mortality. Diabetic retinopathy (DR) is a well-known inflammatory, neurovascular complication of diabetes and a leading cause of preventable blindness in developed countries among working-age adults. However, the ocular surface components of diabetic eyes are also at risk of damage due to uncontrolled diabetes, which is often overlooked. Inflammatory changes in the corneas of diabetic patients indicate that inflammation plays a significant role in diabetic complications, much like in DR. The eye´s immune privilege restricts immune and inflammatory responses, and the cornea and retina have a complex network of innate immune cells that maintain immune homeostasis. Nevertheless, low-grade inflammation in diabetes contributes to immune dysregulation. This article aims to provide an overview and discussion of how diabetes affects the ocular immune system’s main components, immune-competent cells, and inflammatory mediators. By understanding these effects, potential interventions and treatments may be developed to improve the ocular health of diabetic patients.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

Shoulder tendinopathies produce pain and reduce functionality. The aim of this randomized clinical trial was to analyze the effects of Percutaneous electrolysis (PE), Percutaneous peripheral Nerve Stimulation (PNS) and eccentric exercise (EE), on pain (NPRS), strength, electromyographic activity, ultrasound characteristics of the tendon (echogenicity, thickness and hypervascularization) and functionality (DASH and SPADI) on individuals with supraspinatus tendinopathy. Participants (n=50) were divided into two groups, they received 4 treatment sessions, one per week, of PE and PNS (n=25) or 10 treatment sessions of TENS and US (n=25). Both groups performed EE program consisted of 3 sets of 10 repetitions of each of the 3 exercises, twice a day, during the 4 weeks. Follow-up was carried out at 4, 12 and 24 weeks after the start of the intervention. There are statistically significant differences in the analysis between groups (p&lt;0.001) in the post-treatment and follow-up measurements favorable to the PE+PNS+EE treatment on pain (NPRS), strength, supraspinatus electromyographic amplitude, ultrasound characteristics of the tendon (echogenicity, thickness and hypervascularization) and DASH and SPADI questionnaires. The combined treatment PE, PNS and EE is an effective option in the clinical management of tendinopathies, with positive results in the short and long term on the variables studied.

Traumatic nerve injuries are common lesions that affect several hundred thousand humans, as well as dogs and cats. The assessment of nerve regeneration trough animal models may provide information for translational research and future therapeutic options that can be applied mutually in veterinary and human medicine, in a one health perspective. This review offers a hands-on vision about the non-invasive and conservative approaches on peripheral nerve injury, focusing the role of neurorehabilitation in nerve repair and regeneration. The peripheral nerve injury may lead to hypersensitivity, allodynia and hyperalgesia, with the possibility of joint contractures, decreasing functionality and impairing the quality of life. The question remains regarding how to improve nerve repair with surgical possibilities, but also considering electrical stimulation modalities by modulating sensory feedback, upregulation BDNF, GFNF, TrKB and adenosine monophosphate, maintaining muscle mass and modulating fatigue. This could be improved by the positive synergetic effect of exercises and physical activity with locomotor training, and other physical modalities, such as low-level laser therapy and ultrasounds. In addition, the use of cell-based therapies is an innovative treatment tool in this field. These strategies may help avoiding situations of permanent monoplegic limbs that could lead to amputation.

Takayasu arteritis is an inflammatory vasculitis that mainly impacts the large vessels including the aorta and its branches. Ocular manifestations may include retinal ischemia, optic neuropathy, cataracts, and retinal artery occlusion. We present two cases where central retinal artery occlusion was found in patients with Takayasu arteritis and wish to highlight to consider Takayasu arteritis in young patients with unexplained retinal artery occlusion.

The Avian retina is far less known than that of mammals such as mouse and macaque, and detailed study is overdue. The chicken (Gallus gallus) has potential as a model, in part because research can build on developmental studies of the eye and nervous system. One can expect differences between bird and mammal retinas simply because whereas most mammals have three types of visual photoreceptor birds normally have six. Spectral pathways and colour vision are of particular interest, because filtering by oil droplets narrows cone spectral sensitivities and birds are probably tetrachromatic. The number of receptor inputs is reflected in the retinal circuitry. The chicken probably has four types of horizontal cell, there are at least 11 types of bipolar cell, often with bi- or tri-stratified axon terminals, and there is a high density of ganglion cells, which make complex connections in the inner plexiform layer. In addition, there is likely to be retinal specialisation, for example chicken photoreceptors and ganglion cells have separate peaks of cell density in the central and dorsal retina, which probably serve different types of behaviour.

Vertebrate color vision is evolutionarily ancient. Jawless fish evolved four main spectral types of cone photoreceptor, almost certainly complemented by retinal circuits to process chromatic opponent signals. Subsequent evolution of photoreceptors and visual pigments are now documented for many vertebrate lineages and species, giving insight into evolutionary variation and ecological adaptation of color vision. We look at organization of the photoreceptor mosaic and the functions different types of cone in teleost fish, primates, and birds and reptiles. By comparison less is known about the underlying neural processing. Here we outline the diversity of vertebrate color vision and summarize our understanding of how spectral information picked up by animal photoreceptor arrays is adapted to natural signals. We then turn to the question of how spectral information is processed in the retina. Here, the quite well known and comparatively ‘simple’ system of mammals such as mice and primates reveals some evolutionarily conserved features such as the mammalian Blue^ON system which compares short and long wavelength receptors signals. We then survey our current understanding of the more complex circuits of fish, amphibians, birds and reptiles. Together, these clades make up more than 90% of vertebrate species, yet we know disturbingly little about their neural circuits for colour vision beyond the photoreceptors. Here, long-standing work on goldfish, freshwater turtles and other species is being complemented by new insights gained from the experimentally amendable retina of zebrafish. From this body of work, one thing is clear: The retinal basis of colour vision in non-mammalian vertebrates is substantially richer compared to mammals: Diverse and complex spectral tunings are established at the level of the cone output via horizontal cell feedforward circuits. From here, zebrafish use cone-selective wiring in bipolar cells to set-up color opponent synaptic layers in the inner retina, which in turn lead a large diversity of color-opponent channels for transmission to the brain. However, while we are starting to build an understanding of the richness of spectral properties in some of these species’ retinal neurons, little is known about inner retinal connectivity and cell-type identify. To gain an understanding of their actual circuits, and thus to build a more generalised understanding of the vertebrate retinal basis of color vision, it will be paramount to expand ongoing efforts in deciphering the retinal circuits of non-mammalian models.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Peripheral nerve injury remains a medical challenge with no easy resolution. Over the last few decades, significant advances have been achieved in promoting peripheral nerve regeneration, and new assessment tools have been developed, both functional and imaging, to quantify the proportion and quality of nerve recovery. The exploration of new animal models, larger, more complex and with more similarities to humans, has made it possible to reduce the gap between the results obtained in classic animal models such as rodents and the application of new therapies in humans and animals of clinical interest. Ultrasonography is an imaging technique recurrently used in clinical practice to assess the peripheral nerves, allowing its anatomical and topographic characterization, and aiding in the administration of anesthesia and in the performance of nerve blocks. The use of this technique in animal models is scarce, but it could be a useful tool in monitoring the progression of nerve regeneration after the induction of controlled experimental lesions. In this work, sheep, a promising animal model in the area of peripheral nerve regeneration, were subjected to an ultrasonographic study of three peripheral nerves of the hind limb, the common peroneal, tibial and sciatic nerves, in order to establish values of dimensions and ultrasound appearance in healthy nerves and also landmarks for their identification. At the same time, an echographic evaluation of the cranial tibial muscle, an effector muscle of the common peroneal nerve, was also carried out, establishing normal values for the echographic aspect and dimensions. The results obtained will allow the use of these data as control values in future work exploring new therapeutic options for nerve regeneration after induction of common peroneal nerve injuries in sheep.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

The retinal pigment epithelium (RPE), which ensures the normal functioning of the neural retina, is a pigmented single-cell layer that separates the retina from the Bruch's membrane and the choroid. There are three main types of pigment granules in the RPE cells of the human eye: lipofuscin granules (LG) containing the fluorescent “age pigment” lipofuscin, melanoprotein granules (melanosomes, melanolysosomes) containing the screening pigment melanin and complex melanolipofuscin granules (MLG) containing simultaneously both types of pigments - melanin and lipofuscin. This review examines the functional role of pigment granules in the aging process and in the development of oxidative stress and associated pathologies in RPE cells. The focus is on the process of light-induced oxidative degradation of pigment granules caused by reactive oxygen species. The reasons leading to increased oxidative stress in RPE cells as a result of oxidative degradation of pigment granules are considered. A mechanism has been proposed to explain the phenomenon of age-related decline in melanin content in RPE cells. The essence of the mechanism is that when the lipofuscin part of the melanolipofuscin granule is exposed to light, reactive oxygen species are formed, which destroy its melanin part. As more melanolipofuscin granules are formed with age and the development of degenerative diseases, the melanin in pigmented epithelial cells ultimately disappears.

This review focuses on the role of small extracellular vesicles in the pathophysiological mechanisms of retinal degenerative diseases. Many of these mechanisms are related or modulated by the oxidative burden of the retinal cells. It has been recently demonstrated that cellular communication in the retina involves extracellular vesicles and that their rate of release and cargo features might be affected by the cellular environment and in some instances also mediated by autophagy. The fate of these vesicles is diverse, and could end up in the circulation and be used as markers, or target neighbour cells modulating gene and protein expression and eventually also angiogenesis. Neovascularization in the retina promotes vision loss in diseases such as diabetic retinopathy and age-related macular degeneration. The importance of micro RNAs, either as small extracellular vesicles’ cargo or free circulating, on the regulation of retinal angiogenesis is also discussed.

Visual impairment and blindness are a growing public health problem, as they reduce the quality of life of millions of people. The management and treatment of these diseases represent a scientific and therapeutic challenge, since the different cellular and molecular actors involved in the pathophysiology are still being identified. The visual system components, particularly the retinal cells, are extremely sensitive to genetic or metabolic alterations, and immune cells activated by insults contribute to biological events that culminate with vision loss and irreversible blindness. Several ocular diseases are linked to retinal cell loss, and diseases such as retinitis pigmentosa, age-related macular degeneration, glaucoma and diabetic retinopathy are characterized by pathophysiological hallmarks that represent possibilities to study and develop novel treatments for retinal cells degeneration. Here, we present a compilation of revisited information on retinal degeneration, including pathophysiologic and molecular features, biochemical hallmarks and possible directions for novel treatments, aiming to assist as a guide for innovative research. The expansion of knowledge of the mechanistic bases of the pathobiology of eye diseases, including information on the complex interactions of genetic predisposition, chronic inflammation, and environmental and aging-related factors will allow the identification of new therapeutic strategies.

Adipor1^tm1Dgen and Mfrp^rd6 mutant mice share similar eye disease characteristics. Previously, studies established a functional relationship of ADIPOR1 and MFRP proteins in maintaining retinal lipidome homeostasis and visual function. However, the independent and/or interactive contribution of both the genes to similar disease phenotypes, including fundus spots, decreased axial length and photoreceptor degeneration has yet to be examined. We performed a gene-interaction study where homozygous Adipor1^tm1Dgen and Mfrp^rd6 mice were bred together and the resulting doubly heterozygous F1 offspring were intercrossed to produce 210 F2 progeny. Four-month-old mice from all nine genotypic combinations obtained in the F2 generation were assessed for white spots by fundus photo documentation, for axial length by caliper measurements, and for photoreceptor degeneration by histology. Two-way factorial ANOVA was performed to study individual as well as gene interaction effects on each phenotype. Here, we report the first observation of reduced axial length in Adipor1^tmlDgen homozygotes. We show that while Adipor1 and Mfrp interact to affect spotting and degeneration, they act independently to control axial length, highlighting the complex functional association between these two genes. Further examination of the molecular basis of this interaction may help in uncovering mechanisms by which these genes perturb ocular homeostasis.

Age-related macular degeneration is one of the most common causes of blindness, and the incidence exhibits profound racial bias, occurring most frequently in Caucasians. A primary cell type affected in the disease is the retinal pigment epithelium, but the etiology is unclear. The end 10% of the photoreceptor outer segments are shed each day, and the underlying retinal pigment epithelium engulfs, digests, and recycles molecules back to the sensory retina. In previous work, we showed that GPR143 signaling in response to L-DOPA may be effective in the prevention or delay of age-related macular degeneration. In this study, we explore a novel potential effector of GPR143 signaling, that of outer segment uptake and digestion. Using isolated outer segments, labelled with a pH-sensitive marker to fluoresce in lysosomes, we show that GPR143 signaling does not impact outer segment uptake, but does have a significant effect on subsequent degradation. Interestingly, GPR143 signaling did not affect the digestive capacity of the cells, marked by total proteolytic capacity and cathepsin D activity. Rather, our data suggest GPR143 improved endosomal trafficking efficiency of the phagocytosed outer segments to the lysosome. This result is similar to the effect we previously reported for GPR143 on exosome release from the endosomal compartment. Our data illustrate that GPR143 is active in endosomal traffic A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

As in glaucoma and other optic neuropathies cellular dysfunction often precedes cell death, sensitive assessment of retinal ganglion cell (RGC) function represents a key outcome measure for neuroprotective strategies aimed at targeting distressed but still viable cells. Here we offer a conceptual framework to identify progressive stages of RGC dysfunction leading to cell death in mouse models of glaucoma and other optic neuropathies based on non-invasive pattern electroretinogram (PERG), to differentiate phenotypic and altered RGC response dynamics, to assess susceptibility to stressors and to assess reversible dysfunction.

Electrospun nanofiber-supported thin film composite membranes are among the most promising membranes for seawater desalination via forward osmosis. In this study, a high-performance electrospun polyvinylidenefluoride (PVDF) nanofiber-supported TFC membrane was successfully fabricated after molecular layer-by-layer polyelectrolyte deposition. Negatively-charged electrospun polyacrylic acid (PAA) nanofibers were deposited on electrospun PVDF nanofibers to form a support layer consisted of PVDF and PAA nanofibers. This resulted to a more hydrophilic support compared to the plain PVDF nanofiber support. The PVDF-PAA nanofiber support then underwent a layer-by-layer deposition of polyethylenimine (PEI) and PAA to form a polyelectrolyte layer on the nanofiber surface prior to interfacial polymerization, which forms the selective polyamide layer of TFC membranes. The resultant PVDF-LbL TFC membrane exhibited enhanced hydrophilicity and porosity, without sacrificing mechanical strength. As a result, it showed high pure water permeability and low structural parameter values of 4.12 Lm⁻²h⁻¹bar⁻¹ and 221 µm, respectively, significantly better compared to commercial FO membrane. Layer-by-layer deposition of polyelectrolyte is therefore a useful and practical modification method for fabrication of high performance nanofiber-supported TFC membrane.

Disposable surgical gowns are usually made from petroleum-based synthetic fibers that do not naturally decompose, impacting the environment. A promising approach to diminish the environmental impact of disposable gowns involves utilizing natural fibers and/or bio-based synthetic fibers. In this study, composite web from polylactic bicomponent fiber and natural fibers, cattail and kapok fiber, were prepared by hot-press method. Only the sheath region of the PLA bicomponent fiber melts, acting as an adhesive that enhanced the strength and reduced the thickness of the composite web compared to its state before hot-pressing. Mechanical and physical properties of composite webs were evaluated. Composite webs created from kapok fiber displayed a creamy yellowish-white color, while those made from cattail fiber showed a yellowish-brown color. Composite webs exhibit hydrophobic properties when adding the natural fiber. The maximum natural fiber content, at a ratio of 30, can be incorporated into composite webs while preserving mechanical properties and proper water vapor permeability. This nonwoven material presents an alternative with the potential to replace petroleum-based surgical gowns.

Purpose: To evaluate the relationship between corneal nerve structure and function in a veteran population. Methods: 83 veterans (mean age: 55 ± 5 years) seen at the Miami Veterans Affairs (VA) eye clinic were included in the study. Each individual filled out questionnaires to evaluate ocular symptoms (5-Item Dry Eye Questionnaire, DEQ5, Ocular Surface Disease Index, OSDI) and ocular pain (Numerical Rating Scale, NRS, Neuropathic Pain Symptom Inventory modified for the Eye, NPSI-Eye). Individuals also underwent an ocular surface examination that captured functional nerve tests including corneal sensation, corneal staining, and Schirmer test for tear production. Corneal sub-basal nerve analysis was conducted using in vivo confocal microscopy (IVCM) images with corneal nerve density, length, area, width, and fractal dimension captured. IVCM and functional corneal metrics from the right eye were examined using correlational and linear regression analysis. Results: Most corneal structural metrics were not related to functional metrics, except for weak correlations between various IVCM metrics and tear production. In addition, corneal nerve fiber area was positively related to corneal sensation (r = 0.3, p = 0.01). On linear regression analyses, only corneal fractal dimension remained significantly related to tear production (β = -0.26, p = 0.02) and only corneal nerve fiber area remained significantly related to corneal sensation (β = 0.3, p = 0.01). Conclusions: Most corneal nerve structural metrics did not relate to functional metrics in our veteran population, apart from a few weak correlations between structural metrics and tear production. This highlights caution in using corneal nerve anatomy to predict corneal function.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

A nanostructured electrochemical bi-sensor system for analysis of milks has been developed using the Layer by Layer technique. The non-enzymatic sensor [CHI+IL/CuPcS]2, is a layered material containing a negative film of the anionic sulfonated copper phthalocyanine (CuPcS) acting as electrocatalytic material, and a cationic layer containing a mixture of an ionic liquid (IL) (1-butyl-3-methylimidazolium tetrafluoroborate) that enhances the conductivity and chitosan (CHI) that facilitates the enzyme immobilization. The biosensor ([CHI+IL/CuPcS]2-GAO) results from the immobilization of galactose oxidase on the top of the LbL layers. FTIR, UV-vis and AFM have confirmed the proposed structure and cyclic voltammetry has demonstrated the amplification caused by the combination of materials in the film. Sensors have been combined to form an electronic tongue for milk analysis. Principal Component Analysis has revealed the ability of the sensor system to discriminate between milk samples with different lactose content. Using PLS-1 calibration models, correlations have been found between the voltammetric signals and chemical parameters measured by classical methods. PLS-1 models provide excellent correlations with lactose content. Additional information about other components such as fats, proteins and acidity can also be obtained. The method developed is simple and the short response time permits its use in assaying milk samples on-line.

Emotional experiences are a part of our lives. The maladaptive functioning of an individual's emotional field can lead to emotional disturbances of various kinds, such as anxiety and depression. Currently, there is an increasing prevalence of emotional disorders that cause great human suffering and high socio-economic costs. Emotional processing has a biological basis. The major neuroscientific theories of emotion are based on biological functioning, and all of them take into account the anatomy and function of the tenth cranial nerve: the vagus nerve. The vagus nerve connects the subdiaphragmatic and supradiaphragmatic areas and modulates emotional processing as the basis of interoceptive functioning. Auricular vagus nerve stimulation is a new and innovative neuromodulation technique based on the function of the vagus nerve. Several interventions have shown that this new neurostimulation technique is a very promising resource for treating emotional disorders. In this paper, we summarise three neuroscientific theories of emotion, explain what transauricular vagus nerve stimulation is, and present arguments for its use and continued research.

Amyotrophic lateral sclerosis (ALS) is a progressive neurodegenerative disease that affects both the upper and lower motor neurons in the nervous system, causing muscle weakness and severe disability. The progressive course of the disease reduces the functional capacity in the affected patients, limits daily activities and leads to complete dependence on caregivers, ultimately resulting in a fatal outcome. Respiratory dysfunction mostly occurs later in the disease and is associated with a worse prognosis. 46 participans were included in our study, with 23 patients in ALS group and 23 individuals in the control group. The ultrasound examination of the phrenic nerve (PN) was performed by two authors using a high-resolution "Philips EPIQ 7" ultrasound machine with a linear 4-18 MHz transducer. Our study revealed that the phrenic nerve is significantly smaller on both sides in ALS patients compared to the control group arba controls (p < 0.001). Only one significant study on PN ultrasound in ALS, conducted in Japan, also showed significant results (p < 0.00001). These small studies are particularly promising, as they suggest that ultrasound findings could serve as a additinioal diagnostic tool for ALS

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Image registration has an imperative role in medical imaging. In this work, a grey-wolf optimizer (GWO) based non-rigid demons registration is proposed to support the retinal image registration process. A comparative study of the proposed GWO-based demons registration framework with cuckoo search, firefly algorithm, and particle swarm optimization- based demons registration is conducted. In addition, a comparative analysis of different demons registration methods, such as Wang’s demons, Tang’s demons, and Thirion’s demons which are optimized using the proposed GWO is carried out. The results established the superiority of the GWO-based framework which achieved 0.9977 correlation, and fast processing compared to the use of the other optimization algorithms. Moreover, GWO-based Wang’s demons performed better accuracy compared to the Tang’s demons and Thirion’s demons framework. It also achieved the best less registration error of 8.36×10^-5.

Background and Objectives: Ultrasound (US) is a non-invasive tool for the in-vivo detection of peripheral nerve alterations. Materials and Methods: In this study we applied nerve US to assist the discrimination between the spectrum of Amyotrophic Lateral Sclerosis (ALS, n=11), chronic inflammatory demyelinating polyradiculoneuropathy (CIDP, n=5) and genetically confirmed Charcot-Marie-Tooth disease (CMT, n=5). All participants and n=15 controls without neurological diseases underwent high-resolution US of the bilateral tibial nerve. Nerve cross-sectional area (CSA) and nerve microvascular blood flow were compared between the groups and related to cerebrospinal fluid (CSF) measures, clinical symptoms and nerve conduction studies. Analyses are part of a larger multimodal study on the comparison between US and 7 Tesla (T) magnetic resonance neurography (MRN). Results: Patients and controls were matched with respect to their demographical data. CMT had the longest disease duration, followed by CIDP and ALS. CSA was related to age, weight and disease duration. CSA was larger in CMT and CIDP compared to ALS and controls. Blood flow was greatest in CIDP, and higher than in CMT, ALS and controls. In ALS, greater CSA was correlated with greater CSF total protein and higher albumin quotient. US measures did not correlate with clinical scores or nerve conduction studies in any of the subgroups. Conclusion: Our results point towards the feasibility of CSA and blood flow to discriminate between ALS, CIDP and CMT, even in small sample sized groups. In ALS, larger CSA could indicate an inflammatory disease subtype characterized by reduced blood-nerve barrier integrity. Our upcoming analysis will focus on the additive value of 7T MRN in combination with US to disentangle the spectrum between more inflammatory or more degenerative disease variants along the disease groups.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, polymer D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via LBL fabrication method in regulating microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

This paper intends to discuss SSLs, how they work, their advantages and drawbacks. It will end with the author’s thoughts on the efficacy of the system and whether it is a viable solution for the majority of network security problems or if those drawbacks prevent that.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

The retinal pigment epithelium (RPE) is an important monolayer of cells present in the outer retina forming a major part of the blood-retina-barrier (BRB). It performs many essential tasks for the maintenance of retinal integrity and function. With increasing knowledge of the retina, it is getting clearer that both common retinal disorders, like age related macular degeneration, and rare genetic disorders originate in the RPE. This calls for a better understanding of the functions of various proteins within the RPE. In this regard, mice enabling an RPE-specific gene deletion are a powerful tool to study the role of a particular protein within the RPE cells in their native environment, simultaneously negating any potential influences of systemic changes. Moreover, since the RPE cells interact closely with the adjacent photoreceptors, these mice also provide an excellent avenue to study the importance of a particular gene function within the RPE to the retina as a whole. In this review, we outline and compare the features of various Cre mice created for this purpose, allowing researchers a well-informed decision on the choice of Cre mouse to use in relation to their research needs.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

This study investigates the unique morphology and mechanical properties of multi-jet electrospun cashew gum (CG) when combined with high molecular weight polyethylene oxide (PEO) and glycerol. Cashew gum (CG) is an inexpensive, non-toxic polysaccharide derived from Anacardium occidentale trees. Initially, the electrospinnability of aqueous solutions of cashew gum alone or in combination with PEO was evaluated. It was found that cashew gum alone was not suitable for electrospinning; thus, adding a small quantity of PEO was needed to create the necessary molecular entanglements for fiber formation. By using a single emitter with a CG:PEO ratio of 85:15, straight and smooth fibers with some defects were obtained. However, additional purification of the cashew gum solution and the incorporation of glycerol as a plasticizer were necessary to produce defect-free straight and smooth fibers. Interestingly, when the optimized formulation was electrospun using multiple simultaneous emitters, thicker aligned fiber bundles were achieved. Moreover, the resulting oriented fiber mats exhibited unexpectedly high elongation at break at ambient conditions. These findings highlight the potential of this bio-polysaccharide-based formulation for non-direct water contact applications requiring elastic properties.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

The intricate functionality of the vertebrate retina relies on the interplay between neurotransmitter activity and calcium dynamics, offering important insights into de-velopmental processes, physiological functioning, and disease progression. Neuro-transmitters orchestrate cellular processes to shape the behavior of the retina under diverse circumstances. Despite research to elucidate the roles of individual neuro-transmitters in the visual system, there remains a gap in our understanding of the holistic integration of their interplay with calcium dynamics in the broader context of neuronal development, health, and disease. To address this gap, the present review explores the mechanisms used by the neurotransmitters glutamate, GABA, glycine, dopamine, and acetylcholine and their interplay with calcium dynamics. This con-ceptual outline is intended to inform and guide future research, underpinning novel therapeutic avenues for retinal-associated disorders.

This study aims to precisely characterize the use of magnetoelectric nanoparticles (MENPs) for stimulating peripheral nerves. Numerical methods were employed to quantify the interaction between MENPs and nervous tissue. The influence of MENPs orientation, concentration and distance was assessed in terms of the external potential distribution exerted by the MENPs, the amplification of the exerted MENPs stimulation required to excite the neural fibers and the current injected into the intracellular space. The results highlight the significance of MENPs concentration for stimulation accuracy and efficiency, the impact of MENPs orientation on the electric potential distribution sensed by the nervous tissue, as well as the importance of the MENPs distance over the fibers’ recruitment. Given the considerable variability in the interaction between MENPs and nerves, our research provides a crucial step towards understanding this interaction, offering quantitative support for the application of MENPs in nervous tissue stimulation.

Extracellular vesicles (EVs), including exosomes, microvesicles, and other lipid vesicles derived from cells, play a pivotal role in intercellular communication by transferring information between cells. EVs secreted by progenitor and stem cells have been associated with the therapeutic effects observed in cell-based therapies, and they also contribute to tissue regeneration following injury, such as in orthopedic surgery cases. This review briefly explores the involvement of EVs in tissue repair and nerve regeneration, their potential as drug carriers, and their significance in stem cell research and cell-based therapies. It underscores the importance for bioengineers to comprehend and manipulate EV activity to optimize the efficacy of tissue engineering and regenerative therapies.

Optic nerve disorders encompass a wide spectrum of conditions characterized by the loss of retinal ganglion cells (RGCs) and subsequent degeneration of the optic nerve. The etiology of these disorders can vary significantly, but emerging research highlights the crucial role of oxidative stress, an imbalance in the redox status characterized by an excess of reactive oxygen species (ROS), in driving cell death through apoptosis, autophagy, and inflammation. This review provides an overview of ROS-related processes underlying four extensively studied optic nerve diseases: glaucoma, Leber's hereditary optic neuropathy (LHON), anterior ischemic optic neuropathy (AION), and optic neuritis (ON). Furthermore, we present preclinical findings on antioxidants, with the objective of evaluating the potential therapeutic benefits of targeting oxidative stress in the treatment of optic neuropathies.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

Dysfunction and selective loss of retinal ganglion cells (RGCs) is a known cause of vision loss in glaucoma and other neuropathies where ocular hypertension (OHT) is the major risk factor. We investigated the impact of transient non-ischemic OHT spikes (spOHT) on RGC function and viability in vivo to identify cellular pathways linking low-grade repetitive mechanical stress to RGC pathology. We found that repetitive spOHT had an unexpectedly high impact on intraocular homeostasis and RGC viability, while exposure to steady OHT (stOHT) of similar intensity and duration failed to induce pathology. The repetitive spOHT induced a rapid activation of the inflammasome, marked by the upregulation of NLRP1, NLRP3, AIM2, caspases -1, -3/7, -8, gasdermin D (GsdmD) and the release of interleukin-1β (IL-1β) and other cytokines into the vitreous. Similar effects were also detected after 5 weeks of exposure to chronic OHT in an induced glaucoma model. The onset of these immune responses in both spOHT and glaucoma models preceded a 50% deficit in pattern electroretinograms (PERG) amplitude, and significant loss of RGCs at 7 days post-injury. Inactivation of inflammasome complexes in NLRP1-/- , Casp1-/- and GsdmD-/- knockout animals, significantly suppressed the spOHT induced inflammatory response and protected RGCs. Our results demonstrate that mechanical stress produced by acute repetitive spOHT or chronic OHT is mechanistically linked to inflammasome activation, which leads to RGC dysfunction and death.

Retinal pigment epithelial (RPE) cells are the major cell type in the epi- or sub-retinal membranes in the pathogenesis of proliferative vitreoretinopathy (PVR), which is a blinding fibrotic eye disease and still short of effective medicine. The purpose of this study is to demonstrate if Chalocomoracin (CMR), a novel purified compound from fungus-infected mulberry leaves, is able to inhibit vitreous-induced signaling events and cellular responses intrinsic to PVR. Our studies have revealed that the CMR IC50 for ARPE-19 cells is 35.5 μM at 72 hours, and that 5 μM CMR inhibits vitreous-induced Akt activation and p53 suppression; in addition we have discovered that this chemical effectively blocks vitreous-stimulated proliferation, migration and contraction of ARPE-19 cells, suggesting that CMR is a promising PVR prophylactic.

The present Feature Paper highlights the application of bacterial surface (S-) layer proteins as versatile components for the fabrication of biosensors. One technologically relevant feature of S‑layer proteins is their ability to self-assemble on many surfaces and interfaces to form a crystalline 2D protein lattice. The S-layer lattice on the surface of a biosensor becomes part of the interface architecture, linking the bioreceptor to the transducer interface, which may cause signal amplification. The S-layer lattice as ultrathin, highly porous structure with functional groups in a well-defined special distribution and orientation and an overall anti-fouling characteristics can significantly raise the limit in terms of variety and ease of bioreceptor immobilization, compactness of bioreceptor molecule arrangement, sensitivity, specificity, and detection limit for many types of biosensors. The present paper discusses and summarizes examples for the successful implementation of S-layer lattices on biosensor surfaces in order to give a comprehensive overview on the application potential of these bioinspired S-layer protein-based biosensors.

Here, we investigate the actuation dynamics of a micro device with different intervening liquids between the actuating components under the influence of Casimir and dissipative hydrodynamic forces. This is enabled via phase space portraits, which demonstrate that by increasing the dielectric response of the intervening layer the device may not come into stiction due to the decreasing in magnitude Casmir force. Moreover, it is feasible to expand area of motion using intervening liquids with lower dynamic viscosity or increasing the slip length of the intervening fluid. Finally, under the influence of an external driven force, which is the realistic case for possible applications, the system can reach stable oscillation at larger separations with an amplitude higher for the liquid that lead to lower Casimir and hydrodynamic forces.

Objectives- The aim of the study is to describe and validate an optical-coherence-tomography (OCT) based method to easily calculate specific volumes, overcoming the inability of current OCT software to automate a volumetric analysis for specific entities in retinal pathologies. Methods- After manual drawing with caliper of the specific entity on linear OCT scans and consequent automated measurement of its area, the following formula was used for volumetric calculation: Volume [mm³] = ∑area [mm²] x OCT-scan distance [mm]. Two independent observers calculated the retinal volume (RV) in eyes with normal foveal profile (NFP) and compared it with the automated measurements performed by the OCT software; as well as the volume of the foveal cavity (FC) or foveoschisis (FS) in eyes with lamellar macular hole (LMH). The measurements were re-acquired after six weeks. Intra- and inter-observer variability and variability with automated RV calculations were analysed. Results- The study included 62 eyes: 30 NFP and 32 LMH eyes. High degree of agreement was determined for inter-observer and intra-observer variability between the two observers or singular observer with Spectralis for RV in NFP eyes; as well as between the two observers for FC/FS volume in LMH eyes. Conclusions- We describe and validate, showing excellent inter- and intra-observer agreement, an easy, reliable and widely applicable method to calculate volumes which can be applied to any entity requiring a specific study in the context of retinal pathologies.

A better study of the postnatal retinal development is not only essential for the in-depth understanding of the nature of the vision system but also may provide insights for treatment developments of eye conditions, such as retinopathy of premature (ROP). To date, quantitative analysis of postnatal retinal development is primarily limited to endpoint histological examination. This study is to validate in vivo optical coherence tomography (OCT) for longitudinal monitoring of postnatal retinal development in developing mouse eyes. Three-dimensional (3D) frame registration and super averaging were adopted to investigate the fine structure of the retina. Interestingly, a hyporeflective layer (HRL) between the nerve fiber layer (NFL) and inner plexiform layer (IPL) was observed in developing eyes and gradually disappeared with aging. To interpret the observed retinal layer kinetics, a model based on eyeball expansion, cell apoptosis, and retinal structural modification was proposed.

Retinopathy is a human eye disease that causes changes in retinal blood vessels that leads to bleed, leak fluid and vision impairment. Symptoms of retinopathy are blurred vision, changes in color perception, red spots, and eye pain. In this paper, a new methodology based on Convolutional Neural Networks (CNN) is developed and proposed to diagnose and give a decision about the presence of retinopathy. The CNN model is trained by different images of eyes that have retinopathy and those which do not have retinopathy. The performance of the proposed model is compared with the related methods of DREAM, KNN, GD-CNN and SVM. Experimental results show that the proposed CNN performs better.

Road infrastructure is a key public asset because it benefits the social and economic development of any country. It plays an important role for the development of the industrial complex, the production sector and the road surfaces of transport roads should be of high quality, have a long service life. Road infrastructure, as well as all infrastructure, requires preservation, maintenance and repair. There are special requirements for the roadway that must be observed during construction or repair. This article is devoted to a detailed study of the use of fiber optics sensors (FOS) based on the fiber Bragg grating (FBG) for road surface monitoring. Such a fiber sensor consisting of a fiber Bragg grid and a pair of grids can offer the possibility of simultaneous measurement of deformation and temperature for monitoring the pavement. Temperature and deformation measurements were carried out by installing a sensor on the surface of a made asphalt sample. The built-in fiber sensor based on FBG provides important information about how the pavement structure can withstand the load, subsidence of soil, timely implement road safety and stability measures evaluate and predict the service life of the pavement. The results of the study showed that the synchronicity, repeatability and linearity of the characteristics of the fiber sensor are excellent. The difference between the experimental and theoretical results is about 7%. Thus, based on the results of the obtained data, the fiber sensor on the FBG can be used for monitoring, designing road surfaces and in general transport infrastructure.

Five years ago, the concept of addressed fiber Bragg structures (AFBS) was proposed, which simultaneously perform the functions of a two-frequency radiation shaper, the difference frequency of which is the AFBS address, and a sensitive element, since the value of the difference frequency is invariant to measured physical fields, and the set of difference frequencies, moreover, is orthogonal in the array of such sensors, enabling their address multiplexing. In this article, we provide an overview of the theory and technology of AFBS, including the structures with three or more spectral components with various combinations of difference frequencies, symmetrical and asymmetric, performing the functions of the address and converting information signals to the low-frequency range at the same time, along with other functions. The subjects of interrogation of these structures, their fabrication and calibration are discussed as well. We also consider a wide range of applications in which AFBS can be used, covering such areas as oil and gas production, power engineering, transport, medicine, etc. In addition, the prospects of AFBS further development are proposed.

Nutrition is crucial for the management of patients affected by chronic kidney disease (CKD) to slow down disease progression and to correct symptoms. The mainstay of the nutritional approach to renal patients is protein restriction coupled with adequate energy supply to prevent malnutrition. However, other aspects of renal diets, including fiber content, can be beneficial. This paper summarizes the latest literature on the role of different types of dietary fiber in CKD, with special attention to intestinal microbiota and the potential protective role of renal diets. Fibers have been identified based on aqueous solubility, but other features, such as viscosity, fermentability, and bulking effect in the colon should be considered. A proper amount of fiber should be recommended not only in the general population but also in CKD patients, to achieve an adequate composition and metabolism of intestinal microbiota and to reduce the risks connected with obesity, diabetes, and dyslipidemia.

Nerve hydrodissection (HD), a technique used when treating nerve entrapments, involves using an anesthetic or solution such as saline or 5% dextrose solution to separate the nerve from the surrounding tissue, fascia, or adjacent structures. This technique aims to treat neuropathic pain, or pain caused by the nerve. Ultrasound-guided HD of peripheral nerves has gained significant attention in the medical profession and pain management fields in recent years. This is due to a number of high impact publications of randomized control trials demonstrating the efficacy and safety of this technique for the treatment of carpal tunnel syndrome. Even the 20th edition of Harrison’s Principles of Internal Medicine textbook lists injection of 5% dextrose as an alternative local treatment that does not have the side effects of corticosteroids. At present, there is no review of the current literature on this technique. This manuscript will summarize and discuss the following: 1) the different approaches to doing ultrasound-guided HD of nervous structures, 2) its usages in different clinical situations, 3) its clinical pearls, 4) the solution used, and 5) the postulated mechanisms of action.

The interest in obtaining new composite materials with diverse properties has created a growing interest in natural fi-bers as reinforcement in polymers, which has generated an impact in sectors such as automotive and construction, dis-placing synthetic fibers. Properties such as low density, low cost, and rene.wable make these fibers an attractive alterna-tive to reduce environmental impact. Their application in polymers, such as polypropylene, polyethylene, and epoxy resins, has allowed the modification of polymeric composite materials' mechanical and physical properties (NFRP). This review focuses on investigating the status of natural fiber-reinforced polymers. It analyzes their worldwide demand, chemical characteristics, physical and mechanical properties, and various applications in different sectors and indus-tries. In addition, the advantages and disadvantages of NFRPs are highlighted, highlighting their potential for new ap-plications.

Ultra-wide field optical coherence tomography (UWF-OCT) has been recently introduced into clinical ophthalmological practice. To date, there is little data on the reference values of retinal thickness (RT) and choroidal thickness (CT) measured with this technique. This study aimed to analyze the variance of RT and CT in healthy eyes with UWF-OCT tests performed with the largest available scan size of 23 x 20 mm. The data were analyzed with reference to the patients' age, gender, and the axial length of the eyeball. The results of UWF-OCT scanning enabled us to picture the shape of the retina and choroid in a large portion of the eyeball. Both anatomical entities become significantly thinner at the periphery. The peripheral CT is greater in the upper and temporal sectors; the RT is higher in the nasal compared to the temporal sectors. Both choroid and retina lose thickness with age, however, CT and RT do not show a statistically significant correlation with the axial length after adjusting for age and gender. Age-related variations in thickness are especially prominent in the choroid. The CT in UWF-OCT testing is significantly greater in females while the RT is greater in males. UWF-OCT testing provides additional information on the anatomical structure of the retina and choroid compared to standard-field OCT

Prevention of obstetric trauma from damage to the pelvic floor is not always possible and sacral nerve stimulation (SNS) may be necessary later in life. Sacral nerve stimulation has been a promising innovation in the management of moderate to severe faecal incontinence and following sphincter repair failure. Although the indication spectrum for SNS is expanding, the success of neuromodulation for constipation is limited. Adverse events of SNS requiring re-intervention are not common but a long-term successful outcome may depend on interventions for maintenance of the device.

It is well known that fiber sizing is one of the most important component in the manufacturing of composites, and it does affect the mechanical properties including strength and stiffness. In this work, the influence of fiber sizing levels on the mechanical properties of carbon fibers (CF) is reported at room temperature by using single fiber tensile testing (Favimat+), single fiber pullout testing (SFPO), and interfacial elemental analysis using X-ray photoelectron spectroscopy (XPS). Standard modulus of CF (7±0.2 μm in diameter) were sized using two Michelman commercially available sizing formulations. The average solid content for each sizing formulation is 26.3 ± 0.2% and 34.1 ± 0.2%, respectively. HEXION RIMR 135 with curing agent RIMH 137 was used as a model thermoset epoxy matrix during the SFPO measurements. A predictive engineering fiber sizing methodology is also developed. Sizing amounts of 0.5, 1, and 2 wt. % on the surface of the fiber is achieved for both sizing formulations. For each fiber sizing level, 50 single fiber tensile testing experiments and 20 single fiber pull-out tests were conducted. The ultimate tensile strength (σult) of the carbon fibers and the interfacial shear strength (τ_app) of the single fiber composite were analyzed. it is also investigated the effect of the sizing levels on the interfacial shear stress and the O/C (Oxygen/Carbon) surface composition ratio. As a result, generalized fiber sizing and characterization methods were established. The developed methods can be used to characterize the strength and interfacial shear strength of any man-made fibers with different sizing formulations and solid contents, irrespective of the matrix i.e. thermoset or thermoplastic.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Background: We evaluate the genetic and phenotypic features of a cohort of 12 Italian patients affected by Retinitis Pigmentosa (RP) associated with RP1 sequence variants.; Methods: Retrospective, single center study (Careggi Hospital, Florence), including a cohort of twelve Italian patients (Five male and seven female) affected by RP carrying pathogenic variants of the RP1 gene. A complete ophthalmic assessment and pedigree analysis was conducted with focus on the onset of disease symptoms, the patient’s age at the first diagnosis, the follow up duration and the possible presence of comorbidities; Results: The mean age at onset of symptoms was 31,0 ± 24,1 years old, with a mean follow-up period of 9,1± 2,4 years. The main symptoms at presentation were hemeralopia and visual field constriction. Fundus evaluation revealed a classic type of RP. Fundus autofluorescence (FAF), Optical Coherence Tomography (OCT), Electroretinogram (ERG), and visual field confirmed in most of the cases the typical features of classic retinitis pigmentosa.; (4) Conclusions: This single-center cohort of Italian patients provided information on the clinical and genetic features of RP1-associated RP. By comprehensively clarifying the genetic variations and their associated clinical manifestations, we can better tailor therapeutic interventions aimed at targeting specific genetic abnormalities. This ultimately promises to improve the prognosis and quality of life for individuals with RP-associated RP1.

The purpose of the study was to determine the “retinal thickness deviation” (RTD) in diabetic macular edema (DME) eyes treated with intravitreal therapy and to establish associations be-tween RTD and best-corrected visual acuity (BCVA). We conducted a retrospective study, in-cluding consecutive DME eyes undergoing intravitreal therapy with two years of follow-up. BCVA and central subfield thickness (CST) were collected at baseline, 12 months and 24 months of follow-up. RTD was calculated as the absolute difference between measured and normative CST values at each time point. Linear regression analyses were performed between RTD and BCVA and between CST and BCVA. One hundred and four eyes were included in the analysis. The RTD was 177.0 (117.2) μm at baseline, 97.0 (99.7) μm at 12 months and 89.9 (75.3) μm at 24 months of follow-up (P < .001). RTD showed a moderate association with BCVA at baseline (R2=0.134, p<0.001) and 12 months (R2=0.197, p<0.001), and a substantial association at 24 months (R2=0.272, p<0.001). The CST showed a moderate association with BCVA at baseline (R2=0.132, p<0.001) and 12 months (R2=0.136, p<0.001), while the association was weak at 24 months (R2=0.065, p=0.009). In conclusion, RTD showed a good association with visual outcome in DME eyes undergoing intravitreal treatment.

Convolutional neural network architectures have become increasingly complex, which has improved the performance slowly on well-known benchmark datasets in the recent years. In this research, we have analyzed the true need for such complexity. We have introduced G-Net light, a lightweight modified GoogleNet with improved filter count per layer to reduce feature overlaps and complexity. Additionally, by limiting the amount of pooling layers in the proposed architecture, we have exploited the skip connections to minimize the spatial information loss. The investigations on the proposed architecture are evaluated on three retinal vessel segmentation publicly available datasets. The proposed G-Net light outperforms other vessel segmentation architectures by reducing the number of trainable parameters..