Lipophilicity can be measured with different methods, such as Shake-Flask or liquid chromatography. HPLC presents the advantage of overcoming solubility issues and therefore extending the range of lipophilicity to high values. A specific HPLC method, called ELogD, had been developed 20 years ago on a C₁₆-amide stationary phase, enhancing hydrophobic and hydrogen bond interactions to mimic octanol-water partition. The emergence of novel stationary phases added to the need for a less complex mobile phase has led to the development of a new HPLC assay called alphaLogD, applicable to neutral and basic compounds at pH 7.4, that combines superficially porous particles, a high number of equilibriums between solutes and stationary phase, and results in a lower number of isocratic methods to determine the logk’_w at a higher throughput. Statistical studies have been run to successfully evaluate the alphaLogD method compared to the Shake-Flask method and to allow this lipophilicity measurement into the so-called Beyond-Rule-of-5-molecules space.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

Abstract: The quantitative analysis of the chromatographic behavior of basic compounds was performed in silico. The liquid chromatography (LC) data measured with pentyl-, hexenyl-, and octyl-bonded silica gels were analyzed in silico employing model phases. The main retention force was the van der Waals (VW) interaction, and the main desorption force was an electrostatic (ES) interaction. The contribution of hydrogen bonding (HB) was weak compared to that for acidic compounds. The quantitative explanation was achieved utilizing the calculated VW, HB, and ES energy values obtained from a molecular mechanics program. The electron localization was observed at the molecular interaction-site calculated MOPAC program. This fundamental approach was like that of explaining chemical reactions. The difference was electron localization in chromatography or electron transfer in a chemical reaction.

Background: Recurrent approximation of retention parameters in reversed-phase HPLC is effective for revealing anomalies difficult to detect otherwise, namely, the reversible hydration of analytes. This was demonstrated previously for restricted sets of analytes with acetonitrile–water eluents. Expanding the number of analytes and eluents seems to be a topical problem. Two kinds of derivatives of aromatic carbonyl compounds were characterized: unsubstituted hydrazones and oximes. Methods: If analyte demonstrates no anomalies in dependences of retention times vs. concentration of organic modifier, the recurrent approximations of these dependences are linear. To explain the features of recurrent approximations, the numerical experiments were proposed and considered. The artificial shifting of one, two, or more points allows modeling the different kinds of deviations of approximations from linearity. Results: It was shown that hydrazones are the class of analytes having no anomalies of retention parameters. On the contrary, several anomalies were detected for oximes. Downward deviations of points in the plots of recurrent approximations of retention times are the signs of reversible hydration. This effect for methanol–water eluents was detected for the first time. Some of oximes underwent hydrolysis. Conclusion: Recurrent approximation of retention times allows detecting chemical transformations of analytes during RP HPLC analysis.

Separation of polyethylene glycols (PEGs) into single homologs by reversed-phase chromatography is investigated experimentally and theoretically. The used core-shell column is shown to achieve baseline separation of PEG homologs up to molar weights of at least 5000 g/mol. A detailed study is performed elucidating the role of the operating conditions temperature, eluent composition, and degree of polymerization of the polymer. Applying Martin's rule yields a simple model for retention times that holds for a wide range of conditions. In combination with relations for column efficiency, the role of the operating conditions is discussed and separations are predicted for analytical-scale chromatography. Finally, the approach is included in an efficient process model based on discrete convolution, which is demonstrated to predict with high accuracy also advanced operating modes with arbitrary injection profiles.

The polysaccharide-based chiral stationary phase (CSP) columns for high-performance liquid chromatography (HPLC) were applied in the separation of liquid crystalline racemic mixtures obtained based on (R,S)-2-octanol and were found to be highly effective in recognizing isomers of minor structural differences. The mobile phase (MP), which consists of acetonitrile (ACN)/water (H2O) at different volume ratios, was used. All measurements were made at room temperature. The order of the elution was also determined. The chromatographic parameters such as resolution - (Rs), selectivity - (α), and the number of theoretical plates, i.e., column efficiency - (N), were determined. The polysaccharide-based CSP columns have unique advantages in separation technology, and this study has shown the potential usefulness of the CSP columns in separating liquid crystalline racemic mixtures belonging to the same homologous series.

A sustainable reversed-phase chromatographic method has been developed and validated for the simultaneous determination of three active pharmaceutical ingredients, dorzolamide, brinzolamide, and timolol, used to treat glaucoma. The eco-friendly solvent isopropanol has been used as an organic mobile phase constituent. According to the Hansen space green solvent selection tool, isopropanol has a G score of 6.5, comparable to ethanol, which has a G score of 6.6. The mobile phase consists of isopropanol: aqueous sodium acetate buffer (0.1 M, pH 4.25) in the ratio of 10:90 (v/v). The flow rate was maintained at 1 mL/min. Dorzolamide and brinzolamide were detected at 254 nm, and timolol was detected at 295 nm. A high-purity silica with a polymeric C18 modification column (5 µm,150 x 4.6 mm) was used for this separation. The three compounds were eluted within 8 min. The method was validated according to ICH guidelines. The calibration curves were linear in the range of 20-70 µg/mL, 40-140 µg/mL, and 20-70 µg/mL for dorzolamide, brinzolamide, and timolol, respectively. The LODs were found to be 1.61 µg/mL, 1.60 µg/mL, and 3.16 µg/mL for dorzolamide, brinzolamide, and timolol, respectively. Good accuracy and precision were obtained for the three compounds. The greenness and whiteness of the method were indicated using the AGREE and RGB12 tools, respectively.

Fingerprints are essential for human identification and are valuable tools in criminal investigations. The pursuit of new materials for digital printing is expanding, with increasing interest in natural compounds such as bixin, sourced from annatto seeds. Despite its traditional use as a natural dye with medicinal properties, the potential of bixin in papilloscopy remains largely untapped. In this study, we meticulously extracted bixin from annatto seeds and meticulously developed composites incorporating zinc carbonate (bixin/ZnCO3) and kaolinite (bixin/kaolinite). UV-visible spectroscopy was used for characterization, and the extracted bixin showed absorption peaks at 429, 453, and 481 nm, which were very similar to standard peaks at 429, 457, and 487 nm. The two samples also had the same retention times (7.07 min) according to further liquid chromatography analysis. Sweat pores were easier to detect thanks to the effectiveness of the bixin/ZnCO3 and bixin/kaolinite composites in creating high contrast sebaceous and natural latent fingerprints. These results highlight the composites’ potential as novel and fascinating instruments for papilloscopy applications, which might also improve forensic investigations.

The analysis of chemical warfare agents and their degradation products has become increasingly important for public and military safety in recent years. In the article, we drew attention to the possibilities of the HPLC-ICP-MS analytical technique, which has been relatively rarely used for identifying and quantitatively analyzing highly toxic and hazardous substances in environmental samples. This technique enables the identification and determination of minimal amounts (ppt range) of chemicals in various matrices. This fact is important for the analysis of chemical warfare agents and other highly harmful compounds, even small amounts of which can have serious consequences for living organisms. The article critically analyzes the results of scientific research on the identification and quantitative analysis of extremely toxic organophosphorus, organosulfur and organoarsenic substances, their derivatives and degradation products using high-performance liquid chromatography (HPLC) coupled with inductively coupled plasma mass spectrometry (ICP-MS).

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

Cadmium (Cd) is a metal with no nutritional or physiological value, but is found in most people because it is a contaminant in nearly all food types. The intestinal absorption rate determines the body burden of Cd because humans lack a physiologic mechanism for excretion of the metal. Most acquired Cd accumulates in the kidneys, in which the Cd content increases through age 50 but falls thereafter. The decline from maximal kidney content is probably due to release of Cd from injured tubular cells into urine and replacement of destroyed nephrons by scar tissue. Chronic kidney disease is diagnosed when the estimated glomerular filtration rate (eGFR) falls below 60 mL/min/1.73 m2, or when albuminuria is present. Albuminuria is defined as an albumin-to-creatinine ratio ≥ 30 mg/g creatinine in women or ≥ 20 mg/g creatinine in men that persists for at least 3 months. Generally, Cd-induced reductions in eGFR are not reversible, and Cd nephropathy may progress to end-stage kidney disease. There is no evidence that elimination of current environmental exposure can reverse Cd nephropathy, and no theoretical reason to believe that such a reversal is possible. This review provides an update of knowledge concerning CKD in population environmentally exposed to Cd. Special attention is devoted to mechanisms of Cd-induced albuminuria concurrently with eGFR reductions, and the difficult challenge of exposure guidelines sufficient to eliminate the risk of Cd-induced CKD is addressed.

In this paper, we identify several relative ordering properties of the modified proportional hazard rate and modified proportional reversed hazard rate models. For this purpose, we use two well-known relative orderings, namely the relative hazard rate ordering and the relative reversed hazard rate ordering. The investigation is to see how a relative ordering between two possible base distributions for the response distributions in these models is preserved when the parameters of the underlying models are changed. We will give some examples to illustrate the results and the conditions under which they are obtained.

This review is dedicated to sustainable practices in liquid chromatography. HPLC and UHPLC methods contribute significantly to routine analytical techniques. Therefore, the transfer of classical liquid chromatographic methods into sustainable ones is of utmost importance in moving toward sustainable development goals. Among other principles to render a liquid chromatographic method green, substitution of the organic solvent component in the mobile phase with a greener one received great attention. This review concentrates on choosing the best alternative green organic solvent to replace the classical solvent in the mobile phase for easy rapid transfer to a more sustainable normal phase or reversed-phase liquid chromatography. The main focus of this review will be on describing the transfer of non-green to green and white chromatographic methods in an effort to elevate the sustainability best practice in analytical chemistry. The greenness properties and greenness ranking in addition to the chromatographic suitability of seventeen organic solvents for liquid chromatography are mentioned to have a clear insight into the issue of rapidly choosing the appropriate solvent to transfer a classical HPLC or UHPLC method into a more sustainable one. A simple guide is proposed for making the liquid chromatographic method more sustainable.

Background: The scaffold protein tyrosine kinase substrate 4 (TKS4) undergoes tyrosine phos-phorylation by the epidermal growth factor receptor (EGFR) pathway via Src kinase. The TKS4 deficiency in humans is responsible for the manifestation of a genetic disorder known as Frank-Ter Haar syndrome (FTHS). Based on our earlier investigation, the absence of TKS4 triggers migration, invasion, and epithelial-mesenchymal transition (EMT)-like phenomena while concurrently suppressing cell proliferation in HCT116 colorectal carcinoma cells. This indicates that TKS4 may play a unique role in the progression of cancer. In this study, we demonstrated that the enhancer of zeste homolog 2 (EZH2) and the histone methyltransferase of polycomb repressive complex 2 (PRC2) are involved in the migration, invasion, and EMT-like changes in TKS4-deficient cells (KO). EZH2 is responsible for the maintenance of the trimethylated lysine 27 on histone H3 (H3K27me3). Methods: We performed the transcriptome sequencing, chromatin immunoprecipitation, protein and RNA quantitative studies, cell mobility, invasion, and proliferation studies combined with/without EZH2 activity inhibitor 3-deazanoplanocine (DZNep) Results: We detected an elevation of global H3K27me3 levels in the TKS4 KO cells, which could be reduced with treatment with DZNep, an EZH2 inhibitor. Inhibition of EZH2 activity reversed the phenotypic effects of the knockout of TKS4, reducing the migration speed and wound healing capacity of the cells as well as decreasing the invasion capacity, while the decrease in cell prolif-eration became stronger. In addition, inhibition of EZH2 activity also reversed most epithelial and mesenchymal markers. We investigated the wider impact of TKS4 deletion on the gene expression profile of colorectal cancer cells using transcriptome sequencing of wild-type and TKS4 knockout cells, particularly before and after treatment with DZNep. Additionally, we observed changes in the expression of several protein-coding genes and long non-coding RNAs that showed a recovery in expression levels following EZH2 inhibition. Conclusions: Our results indicate that the removal of TKS4 causes a notable disruption in the gene expression pattern, leading to the disruption of several signal transduction pathways. Inhibiting the activity of EZH2 can restore most of these transcriptomics and phenotypic effects.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from <5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

The current study focused on reviewing the rapid growing of using magnetic water in different fields of science and measure the influence of several intensities of magnetization on the chemical and electrical properties of tap water treated by reverse osmosis. The work includes circulation of water for 24 h. in magnetic fields of intensity 500, 1000, 1500, and 2000 G. The magnetization of water causes increasing some positive and negative ions in water such as (Mg, K, Na, Cl¯, Alkaline and SiO₂) and decreasing some positive and negative ions (Ca and SO₃). In the near future, the application of concepts of sustainability development in civil engineering have the to produce structures in harmony with these concepts through using of high-performance materials with less impacts on the environmental and have low cost. The main application of using magnetic water is improvement the geotechnical properties of soil through precipitation of calcite which increases the bond between soil particles and then strength of soil.

(1) Background: ganoderic acids (GAs) are specific triterpenes of Ganoderma lucidum. The HPLC fingerprint profile of GAs of the fruiting body has been well-known, but the mycelial fingerprinting remains unclear. (2) Methods: the ethanol extract of the mycelium of G. lucidum (YK-01) was further purified by preparative HPLC. The HPLC spectra for four strains of G. lucidum and one strain of G. formosanum (purple lingzhi) were investigated. (3) Results: nineteen lanostane triterpenes, including five new triterpenes, GA-TP (1), ganodermic acid Jc (GmA-Jc) (2), GmA-Jd (3), GA-TQ1 (4), and ganoderal B1 (5), and fourteen known triterpenes 6-19 were isolated from the ethanol extract. A green chemical HPLC analytical method was developed by using ethanol and acetic acid as mobile phase. These triterpenes comprise of a unique HPLC triterpenoid spectral pattern of G. lucidum mycelium. All four G. lucidum strains showed the same HPLC spectral pattern, whereas G. formosanum displayed a different pattern. Quantitation methods for ganoderic acid T (10) and S (12) were also validated. (4) Conclusions: the triterpenoid HPLC analytical method can be used to identify G. lucidum species, and to determine the contents of GA-T and GA-S.

Turmeric, Curcuma longa L., is a type of medicinal plant characterized by its perennial nature and rhizomatous growth. It is a member of the Zingiberaceae family and is distributed across the world’s tropical and subtropical climates, especially in South Asia. Its rhizomes are highly valued for food supplements, spices, flavoring agents, and yellow dye in South Asia since ancient times. It exhibits a diverse array of therapeutic qualities that encompass its ability to combat diabetes, reduce inflammation, act as an antioxidant, exhibit anticancer properties, and promote anti-aging effects. In this study, organic extracts of C. longa rhizomes were subjected to HPLC separation followed by mass spectrometry analysis. The Global Natural Product Social Molecular Networking (GNPS) approach was utilized for the first time in this ethnobotanically important species to conduct an in-depth analysis of its metabolomes based on their fragments. A total of 30 metabolites including 16 diarylheptanoids, 1 diarylpentanoid, 3 bisabolocurcumin ethers, 4 sesquiterpenoids, 4 cinnamic acid derivatives, and 2 fatty acid derivatives were identified. Among 16 diarylheptanoids identified in this study, five of them are reported for the first time in this species.

Iron is an essential nutrient for humans and microbes, such as bacteria. Iron deficiency occurs commonly in critically ill patients, but iron replacement therapy is not considered during the acute phase of critical illness, since it increases iron availability for invading microbes and oxidative stress. However, persistent iron deficiency in the recovery phase is harmful with potential adverse outcomes such as cognitive dysfunction, fatigue and cardiopulmonary dysfunction. Therefore, it is important to treat iron deficiency timely and efficiently. This article reviews current knowledge about iron-related biomarkers in critically ill patients and provides possible criteria to guide decision-making for iron supplementation in the recovery phase of critical illness.

For quantitative determination of honokiol (HNK) and metformin hydrochloride (M-HCl) by HPLC from formulations and from dissolution studies, a QbD approach using three factors - three levels design was implemented to optimize the chromatographic conditions. To study the impact of each variable on the peak area of both compounds and retention time of last compound eluted, the 3D response surface plots were developed. HNK and M-HCl were separated on a Thermoscientific ODS Hypersyl TM (250 x 4.6 mm, 5 μm) column mantained at 30 C, using 0.02 M acetate buffer (pH = 3) / methanol (15 / 85, v / v) as mobile phase with a flow rate of 1 mL/min. The injected volume was 20 L, and the detection wavelengths were 256 nm for HNK and 236 nm for M-HCl. The validation of proposed method showed a linearity range of 4 – 1200 μg/mL for M-HCl (r2 = 0.9992) and 1 – 300 μg/mL for HNK (r2 = 0.9998), good precision (RSD < 2% for both HNK and M-HCl, in intra- and inter-day studies) and accuracy (mean recovery = 100.09% in the range 99.80 – 100.43% for M-HCl and mean recovery = 100.12% in the range 99.70 – 100.38% for HNK). The environmentally friendly nature of the method was confirmed by the evaluation of the method’s greenness. The proposed method was applied for the determination of HNK and M-HCl from oral dosage forms and in dissolution studies.

The aim of this study, for determination of verteporfin in real samples (simulated body fluid, and simulated tears, 0.9% isotonic sodium chloride solution, Lactated Ringer IV solution for infusion, 5% dextrose IV solution for infusion, lemon juice and drinking water) was the method validation and to examined by HPLC-DAD-UV. Metod validation parameters such as specificity, linearity, precision, accuracy, robustness, limit of detection (LOD) and limit of quantitation (LOQ) for verteporfin were validated and developed according to the International Conference on Harmonization (ICH) Q2 R1 guidelines. The LOD and LOQ for verteporfin were found 0.06 µg/L and 0.2 µg/L, respectively. The recovery values of the optimization and validation for verteporfin were found in the range of 97.5-100.7%. The relative standard deviations (RSD) for vertepofin were <1%. The developed method was successfully applied to real samples with high accuracy and the recoveries (%) from real samples were 99.9, 100, 98.2, 99.2, 99.4, 98.8 and 99.4, respectively.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

The surge in popularity of Delta-8 Tetrahydrocannabinol (D8-THC) products, coupled with a lack of stringent regulation and oversight, has given rise to concerns regarding consumer safety and compliance with existing laws. This article delves into the challenges posed by the unregulated sale of D8-THC products, emphasizing the potential for contamination with prohibited constituents, including Delta-9 Tetrahydrocannabinol (D9-THC). The 2018 Farm Bill dictates that D9-THC concentrations must not exceed 0.3%, necessitating precise testing methods for accurate validation. Existing testing procedures, particularly involving High-Performance Liquid Chromatography (HPLC), face difficulties in distinguishing between D8 and D9 peaks, necessitating adjustments in parameters to enhance accuracy. The development of more refined testing methodologies is crucial for companies to ensure compliance, prevent adverse health effects, and provide consumers with accurately characterized cannabinoid profiles in the products they purchase.

Plaque psoriasis is a common, long-lasting illness that affects the immune system and causes significant negative impacts on a patient's physical health, well-being, and ability to work effectively. Deucravacitinib (DEU) is the first oral medication used in the treatment of plaque psoriasis, a chronic skin condition that causes red, scaly patches on the skin. DEU is a type of medication called an oral Janus kinase (JAK) inhibitor, which works by blocking specific enzymes that play a role in the inflammation and immune response associated with psoriasis. Therefore, a quick, easy, novel, reliable, sensitive, and straightforward Liquid Chromatography-Tandem Mass Spectrometry (LC-MS/MS) approach was used to analyse DEU in plasma samples. The LC-MS/MS method for the determination of DEU in human plasma was based on using trimethoprim as an internal standard (IS). The separation of DEU and IS was carried out via liquid-liquid extraction (LLE). The isolated substances were then subjected to the chromatographic system using the ACE-C18 column (4.6x100 mm, 5 µm). The mobile phase employed consisted of methanol and a solution of 2 mM ammonium formate (80:20 v/v, respectively). The flow rate used was set at 0.9 mL min-1. The creative strategy was performed by running an ABSCIEX API 4000 mass spectrometer with an electron spray ionization source in Multiple Reaction Monitoring (MRM) modes. The ion transitions m/z 426.3  358.2 was used for DEU quantitation, while the ion transitions m/z 291.1  261.1 was used for trimethoprim quantitation. The accuracy, precision, linearity, recovery, and selectivity of DEU were deemed acceptable when validated for a concentration range between 0.500 to 601.050 ng/mL, utilizing a weighting factor of 1/x2.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

In searching for compounds with antioxidant and antifungal activity, our study focused on the subshrub species Empetrum rubrum Vahl ex Willd. (Ericaceae), commonly known as Brecillo or Murtilla de Magallanes. We measured the antioxidant activity of its methanolic extract (MEE) obtained from the aerial parts (leaves and stems). The antioxidant activity of MEE was evaluated in vitro by 2,2-Diphenyl-1-picrylhydrazyl (DPPH) free radical and 2,2′-Azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt (ABTS) cationic radical. Results were expressed in gallic acid and Trolox equivalents for DPPH and ABTS assays, respectively. The antioxidant activities, for the DPPH and ABTS assays, were also calculated as an inhibitory concentration of extract needed to inhibit 50% of the absorbance (IC50 value). The results of IC50 values measured by the DPPH and ABTS methods were 0.4145 mg mL-1 and 0.1081 mg mL-1, respectively. In relation to the antioxidant activity, the total phenolic content (TPC) in MEE was determined by the Folin-Ciocalteu method, and the presence of secondary metabolites groups, including phenolic compounds, was determined by using different standardized test procedures. Phenolic compounds contained in leaves, stems, and fruits of E. rubrum were determined qualitatively by means of high-performance liquid chromatography coupled with mass spectrometry (HPLC-MS) analysis. The antifungal activity of MEE obtained from aerial parts of E. rubrum was tested against Rhizoctonia solani. In vitro, mycelial growth of this fungus was reduced from 90% to 100% in the presence of MEE.

. Protein cysteine S-glycosylation is a relatively rare and less well characterized post-translational modification (PTM). Creating reliable model proteins that carry this modification is challenging. The lack of available model or natural S-glycosylated proteins significantly hampers the development of MS-based methodologies for detecting protein cysteine S-glycosylation in real-world proteomic studies. There is also limited MS-sequencing data describing easier to create synthetic S-glycopeptides. Here, we present the results of an in-depth manual analysis of automatically annotated CID/HCD spectra for model S-glucopeptides. The CID spectra show a long series of y/b-fragment ions with retained S-glucosylation, regardless of the dominant m/z signals corresponding to neutral loss of 1,2-anhydroglucose from the precursor ions. In addition, the spectra show signals manifesting glucosyl transfer from the cysteine position onto Lys, Arg side chains, and a peptide N-terminus. Other spectral evidence indicates that the N-glucosylated initial products of transfer are converted into N-furanosylated (i.e., glycated) structures due to Amadori rearrangement. We discuss the peculiar transfer of the glucose oxocarbenium ion (Glc+) to positively charged guanidinium residue (ArgH+) and propose a mechanism for the gas-phase Amadori rearrangement involving a hydride ion shift.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Solifenacin (SFC) is a potent muscarinic antagonist that effectively reduces bladder muscle contraction, thereby alleviating symptoms such as frequency of micturition and urgency. Oxidation of SFC leads to the formation of impurities like Impurity K. Effective analysis and control of this impurity is crucial for ensuring compliance with regulatory standards and safeguarding patient health. To address these challenges, we propose a novel one-step synthesis of Impurity K from SFC. Impurity K was synthesized using cerium ammonium (IV) nitrate (CAN) in water/acetonitrile as the solvent. Additionally, we describe a new HPLC-MS method for the detection of Impurity K in solifenacin succinate tablets.

An analytical method was established by HPLC-DAD-ELSD with C18-NH2 column tandem for the simultaneous determination of hydrophobic components atractylenolide I, II, III, atractylone and hydrophilic compounds glucose, fructose and sucrose in the dried rhizome of Atractylodes macrocephala Koidz (a natural raw material for health foods, Bai-Zhu aka. in Chinese). The method combines different separation capabilities of reversed-phase liquid chromatography and hydrophilic interaction liquid chromatography, can provide a new choice for the simultaneous determination of hydrophilic and hydrophobic compounds in traditional Chinese medicines and health foods. It provided a reference method for the quality control of Bai-Zhu. The results showed that the linear correlation coefficients of the established column tandem chromatographic method were all greater than 0.9990, the relative standard deviation was 0.1%-2.8%, and the average recovery was 96.7%-103.1%. The contents of atractylenolide I, II, III, atractylone, fructose, glucose, and sucrose in 17 batches of Baizhu were 172.3-759.8 μg/g, 201.4-612.8 μg/g, 160.3-534.2 μg/g, 541.4-8723.1 μg/g, 6.9-89.7 mg/g, 0.7-7.9 mg/g, and 1.2-21.0 mg/g, respectively.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

Sphingosine 1-phosphate (S1P) is a signaling lipid molecule involved in various cellular processes. It is important to develop a quantitative method for S1P to determine endogenous levels and to investigate its functions. Especially since S1P is a tiny lipid component of most biological samples, highly sensitive analysis by LC-MS/MS is required. The main challenge in S1P analysis by chromatography is peak broadening due to the presence of a polar phosphate and zwitterion formation in S1P. In this study, we used hydrogen fluoride (HF) to efficiently remove a phosphate and then analyzed the surrogate, sphingosine, as a sharp peak by LC-ESI-MS/MS. We optimized the dephosphorylation reaction in terms of reaction time, temperature, and HF concentration. Multiple reaction monitoring (MRM) for dephosphorylated form of S1P and C17-S1P as internal standard at m/z transition 300.4&gt;282.4 (quantification ion), 300.4&gt;262.4 (qualification ion), 286.3&gt;268.2 (internal standard). This method was validated by essential parameters such as specificity, linearity, range, LOQ, LOD, accuracy, precision, and repeatability. To confirm this new method, we quantified S1P levels in various serum products (100.02 ~ 284.38 nM). To apply the method in vivo, we analyzed S1P in plasma and kidney tissues obtained from a chronic kidney disease (CKD) mouse model. S1P levels were increased only in CKD kidney tissue but not in plasma. In conclusion, by applying the dephosphorylation step with HF, we established a new sensitive LC-MS/MS quantitative method for S1P that can be applied to biological samples.

A specific HPLC method has been developed and validated for the determination of vanillyl butyl ether in cosmetic products. The extraction procedure with an isopropanol water 1:1 mixture is described. The method uses a RP-C-18 column with isocratic elution and a UV detector. The mobile phase consists of a mixture of acetonitrile and buffer (Na2HPO4 20mM in water) (30:70 v/v) with a variable flow rate. The method was validated with respect to accuracy, precision (repeatability and reproducibility), specificity and linearity. The procedure described here is simple, selective and reliable for routine quality control analysis and stability tests of commercially available cosmetic products.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

A convenient and efficient strategy for the preparation of 2-sulfonylindoles has been achieved through iodophor/H2O2-mediated 2-sulfonylation of indoles with readily available sulfonyl hydrazides in aqueous phase. Iodophor is commercially available and serves as the green catalyst and aqueous phase. A series of 2-sulfonylated products from indoles and N-methylpyrrole were synthesized in moderate yields in only 10 min. Control experiments were also conducted to reveal the mechanism. This method is environment friendly, easy to operate and suitable for a wide range of substrates.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography-mass spectrometry. The reaction mechanism of alkane solution concentration and temperature in the adsorption process was investigated. The adsorption characteristics of heptadecane on the surface and pores of illite and kerogen were elucidated by adsorption isotherm model and adsorption thermodynamic model. The results show that: The concentration of alkane solution contributes to the adsorption of illite and kerogen. As the concentration of the solution continues to increase, the adsorption rate gradually slows down. However, the temperature hardly affects the adsorption rate. At 25℃, 50℃ and 60℃, the adsorption process of illite on alkane solution is more consistent with Langmuir model and Freundlich model, respectively. The difference is that Langmuir model is suitable for describing the whole adsorption process of kerogen on alkane solution. 3) The adsorption process of illite and kerogen to heptadecane solution is an endothermic reaction. Heating helps to accelerate the migration rate of alkanes, which is conducive to the adsorption reaction. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level, and fill the research gap in the application of solid-liquid isothermal adsorption physical experiments to the adsorption and occurrence of shale oil.

Background: Despite advances in the treatment of hepatocellular carcinoma (HCC) over the last few decades, treatment opportunities for patients with HCC remain limited. HCC is the most common form of liver cancer, accounting for approximately 90% of all cases worldwide. Moreover, apart from the current pharmacological interventions, hepatic resection and liver transplantation are the mainstay curative approaches for patients with HCC. Methods: This systematic review included phase I, II, III, and IV clinical trials (CTs) and randomized controlled trials (RCTs) on current treatments for patients with HCC in an Asian population (2013–2023). A total of 427 articles were screened, and 184 non-duplicate publications were identified. After screening titles and abstracts, 96 publications were excluded, and another 28 were excluded after full-text screening. The remaining 60 eligible RCTs/CTs were finally included. Results: Sixty clinical trials fulfilled our inclusion criteria and screened 36 drugs as monotherapy or combination therapy for HCC. Most studies used sorafenib alone or in combination with any of the treatment regimens. Lenvatinib or atezolizumab with bevacizumab was used for HCC after initial sorafenib treatment. Eighteen studies compared the efficacy of sorafenib with that of other drugs, including lenvatinib, cabozantinib, tepotinib, tigatuzumab, linifanib, erlotinib, resminostat, brivanib, tislelizumab, selumetinib, and refametinib. Conclusion: This study provides comprehensive insights into effective treatment interventions for HCC in Asian populations. The overall assessment indicated that sorafenib alone or in combination with atezolizumab and bevacizumab has been the first treatment choice in the past decade to achieve better outcomes in patients with HCC in an Asian population

(1) Background: Triggering receptor expressed on myeloid cells 2 (TREM2) is involved in neu-roinflammation and HIV-associated neurocognitive impairment (NCI). People with HIV (PWH) using cannabis exhibit lower inflammation and neurological disorders. We hypothesized TREM2 dysfunction mediates HIV neuropathogenesis and can be reversed by cannabinoids. (2) Methods: EcoHIV-infected wildtype (WT) and TREM2R47H mutant mice were used to study HIV's impact on TREM2 and behavior. TREM2 and related gene expressions were examined in mono-cyte-derived macrophages (MDMs) from PWH (n=42) and people without HIV (PWoH; n=19) with varying cannabis use via RNA sequencing and qPCR. Differences in membrane-bound and soluble TREM2 (sTREM2) were evaluated using immunocytochemistry (ICC) and ELISA. (3) Results: EcoHIV increased immature and C-terminal fragment forms of TREM2 in WT mice but not in TREM2R47H mice, with increased IBA1 protein in TREM2R47H hippocampi, correlating with worse memory test performance. TREM2 mRNA levels increased with age in PWoH but not PWH. Cannabidiol (CBD) treatment increased TREM2 mRNA alone and with IL1β. RNA-seq showed upregulation of TREM2-related transcripts in cannabis-using PWH compared to naïve controls. IL1β increased sTREM2 and reduced membrane-bound TREM2, effects partially re-versed by CBD. (4) Conclusions: These findings suggest HIV affects TREM2 expression modu-lated by cannabis and CBD, offering insights for therapeutic strategies.

If we accept that human body is a dissipative structure, then the recovery of the body should be considered as a redirection of the enegy flows. The recovery of vertebral cartilage through redirecting of inner dissipative flow requires the understanding of how is this case the fact of reversibility can be proven. We proposed the approach, that according to the collected data, satisfies all the scientific requirements.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

The DEAD-box RNA helicase DDX3X is a multifunctional protein involved in RNA metabolism and stress responses. In this study, we investigated the role of RG/RGG motifs in the dynamic process of liquid-liquid phase separation (LLPS) of DDX3X using cell-free assays and explored their potential link to cancer development through bioinformatic analysis. Our results demonstrate that the number, location, and composition of RG/RGG motifs significantly influence the ability of DDX3X to undergo phase separation and form self-aggregates. Mutational analysis revealed that the spacing between RG/RGG motifs and the number of glycine residues within each motif are critical factors in determining the extent of phase separation. Bioinformatic analysis of cancer genomic datasets uncovered a significant enrichment of DDX3X mutations in RG/RGG motifs across multiple cancer types, particularly in the N-terminal region of the protein. Furthermore, we found that DDX3X is co-expressed with the stress granule protein G3BP1 in several cancer types and can undergo co-phase separation with G3BP1 in a cell-free system, suggesting a potential functional interaction between these proteins in phase-separated structures. DDX3X and G3BP1 may interact through their RG/RGG domains and subsequently exert important cellular functions under stress situation. Collectively, our findings provide novel insights into the role of RG/RGG motifs in modulating DDX3X phase separation and their potential contribution to cancer pathogenesis.

The endometrium, the inner mucosal lining of the uterus, undergoes complex molecular and cellular changes across the menstrual cycle in preparation for embryo implantation. Transcrip-tome-wide analyses have mainly been utilized to study the endometrial receptivity, the prerequisite for successful implantation, with most of the studies, so far, comparing the endometrial transcriptomes between (i) secretory versus proliferative endometrium or (ii) mid-secretory versus early-secretory endometrium. In the current study, we provide the complete transcriptome description of the endometrium across the entire menstrual cycle and, for the first time, comprehensively characterize the proliferative phase of the endometrium. Our temporal transcriptome analysis includes five time points: mid-proliferative, late-proliferative (peri-ovulatory phase), early-secretory, mid-secretory, and late-secretory phases. Thus, we exhaustively unveil the transitions between the consecutive proliferative and secretory phases, highlighting their unique gene expression profiles and possible distinct biological functions. Transcriptome analysis reveals many differentially expressed genes (DEGs) across the menstrual cycle, most of which are phase-specific. As an example of the coordinated gene activity, the expression profile of his-tone-encoding genes within the HIST cluster on chromosome 6 showed an increase in cluster activity during the late-proliferative and a decline during the mid-secretory phase. Moreover, numerous DEGs are shared among all phases. In conclusion, in the current study, we delineate the endometrial proliferative phase-centered view of transcriptome dynamics across the menstrual cycle. Data analysis highlights significant transcriptomic and functional changes occurring during the late-proliferative phase – an essential transition point from the proliferative to the secretory phase. Future studies should explore how the biology of the late-proliferative phase endometrium impacts the achievement of mid-secretory endometrial receptivity or contributes to molecular aberrations leading to embryo implantation failure.

The author previously investigated the thermodynamic properties of the one-dimensional Potts-SOS model on the lattice of positive natural numbers N in [Akin H, Phys. Scr. 99 (2024), 055231]. In this present paper, we extend that research by determining the Gibbs measures for the same mixed-type model using partition functions constructed on a second-order semi-infinite Cayley tree. By leveraging the self-similarity of the Cayley tree, we analyze the behavior of these partition functions and identify the regions where phase transitions occur. We pinpoint these phase transition regions through a stability analysis of the dynamical system associated with the model at specific fixed points.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

The study of the impact of polyQ expansion driven proteotoxicity on cell metabolism has evi-denced NAD molecule as a central player in regulating metabolic response and cell repair in neurodegeneration. The decline in NAD intracellular levels represents a hallmark of ageing aris-ing from a dysregulation between NAD-consuming and biosynthetic enzymatic reactions in which NMNAT plays a key role. By an integrated bioanalytical and proteomic experimental design, the derangement of NAD metabolism deriving from the accumulation of polyQ-Htt protein has been analysed in Saccha-romices cerevisiae harbouring a 103Q-Htt and compared with wild-type Htt, in absence and in presence of a phenolic extract from EVOO, as a source of antioxidant bioactive compounds. Quantification of NAD and its precursors and proteomic analysis of the differential protein ex-pression has been performed by LC-DAD-MS. Chronological lifespan and NAD homeostasis was strongly impaired by proteotoxic polyQ-Htt, eliciting a depletion of NAD levels and accumulation of NaMN. In parallel a downregulation of Sirt2 expression levels has been observed. Phenolic extract administration had no meaningful ef-fects on NAD replenishment to prevent proteotoxicity. NaMN can represent a biomarker of accel-erated aging, and/or a signaling molecule for cell repair.

High-Performance Liquid Chromatography (HPLC) is an advanced analytical technique employed to separate, identify, and quantify components in complex mixtures. The method operates based on the differential affinities of sample molecules for the mobile and stationary phases within a chromatographic column. HPLC is recognized for its high resolution, accuracy, and efficiency, making it indispensable across various fields including pharmaceuticals, biotechnology, environmental analysis, and forensic science. The technique's adaptability to different detectors such as UV-visible, fluorescence, and mass spectrometry enhances its versatility and precision in analyzing a wide array of substances. Despite its advantages, HPLC presents challenges such as high operational costs, the need for specialized expertise, and susceptibility to contamination.Nonetheless, its role in modern analytical chemistry is pivotal, providing crucial insights and supporting developments in diverse scientific and industrial domains. This abstract encapsulates the core aspects of the article, highlighting the significance and applications of HPLC while also acknowledging its limitations.

Artic root is a well-known plant adaptogen with multipotential pharmacological properties. Thin-layer chromatography (TLC) – screening followed by diode-array high-performance liquid chromatography and nuclear magnetic resonance spectroscopy proved to be a reliable and convenient method for simultaneous determination of quality of various herbal raw materials and supplements. This combination allowed for comparing and differentiating arctic root samples as well as defining their authenticity. The study provided information on the chemical and biological properties of the seven chosen samples as well as qualitative and quantitative evaluation of the quality markers: rosavin, salidroside, and p-tyrosol. The absence of rosavin, salidroside, and p-tyrosol in three samples was detected using TLC-screening and confirmed by HPLC-DAD and NMR. The paper highlighted the importance of quality control and strict regulation for herbal medicine supplements and preparations.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

The effect of ceria doping of (ZrO2)1-x(Sm2O3)x crystals on their phase composition, microhardness and fracture toughness has been studied. The (ZrO2)0.995-х(Sm2O3)х(СеО2)0.005 crystals (where x = 0.032, 0.037 and 0.04) have been grown using directional melt crystallization in cold skull. The phase composition and structure of the crystals have been studied using X-ray diffraction, TEM and Raman spectroscopy. The mechanical properties such as microhardness and fracture toughness have been studied using Vickers indentation. It has been shown that the (ZrO2)0.995-х(Sm2O3)х(СеО2)0.005 solid solution crystals contain both Се4+ and Се3+ ions. Phase analysis data suggest that СеО2 doping increases the tetragonality degree of the transformable t phase and reduces the tetragonality degree of the non-transformable t' phase as compared to the (ZrO2)1-x(Sm2O3)x crystals. As a result, the t→m phase transition triggered by the indentation-induced stress in the СеО2 doped crystals is more intense and covers greater regions. СеО2 doping of the solid solutions increases the fracture toughness of all the crystals studied whereas the microhardness of the crystals changes but slightly. СеО2 doping of the (ZrO2)1-х(Sm2O3)х solid solutions in the experimental concentration range does not improve the high-temperature phase stability of the crystals and does not prevent high-temperature degradation of their fracture toughness.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

Abstract: Background: The analysis of vitamins in baby food is a challenging task given the com-plexity of the food matrix, vitamin stability, and strict regulations of the European Union regarding permissible deviations from declared values. Vitamins in food exist in different concentrations and forms and have different stabilities, and it is not straightforward to prepare samples for reliable analysis using the same procedure. Therefore, significant attention has been devoted to optimizing sample preparation in the analysis of vitamins. Methods: This study aims to determine which of the seven applied extraction methods is the most efficient for the simultaneous extraction and deter-mination of A, D, E, and K vitamins in milk and baby food using high-performance liquid chro-matography (HPLC). Different samples of baby food were prepared in seven different ways based on four methods (saponification, enzymatic hydrolysis, solvent extraction, and solid-phase extrac-tion). Results and Conclusion: The best preparation method proved to be solid-phase extraction with a C18 stationary phase, and HPLC with a UV-VIS detector was identified as a sufficiently sensitive technique for the identification and quantification of fat-soluble vitamins in milk and baby food.

This contribution is aimed to measure for the first time the amount of biogenic amines (BAs) in one of the most ancient and traditional sheep cheese produced in Sardinia, Italy: the Protected Designation of Origin (PDO) Fiore Sardo. For doing this, an original RP-HPLC-DAD-UV method has been developed, completely validated in terms of LoD, LoQ, linearity, precision and trueness, and tested on 36 real Fiore Sardo PDO cheese samples produced by four different cheesemakers and marketed by four stores. The average total concentration of the eight BAs (i.e. tyramine, tryptamine, histidine, putrescine, cadaverine, 2-phenylethylamine, spermine and spermidine) measured in Fiore Sardo cheese was 700 mg/kg, with a range between 170 mg/kg and 1100 mg/kg. A great variability in the total amount of BAs has been evidenced among the Fiore Sardo marketed in the four stores as well as for the cheeses purchased in different times in the same store. Tyramine (350 mg/kg), putrescine (150 mg/kg), histamine (80 mg/kg) and cadaverine (30 mg/kg) are the most abundant BAs found in this matrix. Among many factors concurring, the dominant microflora of Fiore Sardo PDO is likely the principal cause of the qualitative and quantitative distribution of BAs in this matrix. Finally, the total amount of BAs found in Fiore Sardo PDO is not able to cause any situation of health alert for consumers.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

Compound-specific isotope analysis (CSIA) can provide unique insights into the cycling of elements including carbon and nitrogen. One approach for CSIA is the use of high-performance liquid chromatography (HPLC) to separate compounds of interest, followed by analysis of these compounds using an elemental analyzer coupled to an isotope ratio mass spectrometer. A key component of this technique is the fraction collector, which automatically collects compounds as they are separated by HPLC. Here we present a fraction collector which is a simple adaptation of a 3D printer, and thus can be easily adopted by any laboratory already equipped for HPLC. In addition to the much lower cost compared to commercial alternatives, this adaptation has the advantage for CSIA that the 3D-printer is able to heat the collected fractions, which is not true for many commercial fraction collectors. Heating allows faster evaporation of the solvent, so that the dried compounds can be measured by EA-IRMS immediately. The procedure can be repeated consecutively so that dilute solutions can have the compounds concentrated for analysis. Any computer-controlled HPLC can be integrated to the fraction collector used here by means of AutoIt.

Epilepsy is known to cause alterations in neural networks. However, many details of these changes remain poorly understood. The objective of this study was to investigate changes in the properties of hippocampal CA1 pyramidal neurons and their synaptic inputs in a rat lithium-pilocarpine model of epilepsy. In the chronic phase of the model, we found a marked loss of pyramidal neurons in the CA1 area. However, the membrane properties of the neurons remained essentially unal-tered. The results of the electrophysiological and morphological studies indicate that the direct pathway from the entorhinal cortex to CA1 neurons is reinforced in epileptic animals, whereas the inputs to them from CA3 are either unaltered or even diminished. In particular, the dendritic spine density in the str. lacunosum moleculare, where the direct pathway from the entorhinal cortex ter-minates, was found to be 2.5 times higher in epileptic rats than in control rats. Furthermore, the summation of responses upon stimulation of the temporoammonic pathway was enhanced by approximately twofold in epileptic rats. This enhancement is believed to be a significant con-tributing factor to the heightened epileptic activity observed in the entorhinal cortex of epileptic rats using an ex vivo 4-aminopyridine model.

More than 700 anthocyanins are described so far, and many different sources are rich in these natural pigments. During the last few years, researchers have been focusing of strategies to recover and purify anthocyanins, from simple liquid-liquid extractions to more advanced supercritical CO2 extractions, however, with such a huge number of different sources, it’s extremely hard to get a simple and fast methodology that fits several sources, not only by the structural nature of the anthocyanins but also by the presence of specific groups of natural compounds. Using simple methodologies like solid-phase extraction resins represents a powerful economical and efficiency strategy. In this work, we tested several sources of structurally distinct anthocyanins, including purple basil, purple cabbage, purple sweet potato, butterfly pea flower, cornflower and wild pansy, in different resins to assess their efficiency in the obtention of anthocyanin-pure extracts. The results showed us that the combination of oasis HLB® resin followed by a cation-exchange SPE with DSC-MCAX® resulted in high-purity anthocyanin extracts for all the cases.

Plantar flexors (PF) spasticity is known to poorly correlate with active dorsiflexion (DF) impairment throughout the swing phase of hemiparetic gait. Spastic Cocontraction, instead, stemming from descending pathways, potentially misdirect antagonist PF activity opposing DF during swing. Electromyographic (EMG) recordings, while unable to differentiate between reflex-based and descending origins, may offer valuable insights into this distinction by exploring PF EMG activity after tibial nerve neurotomy (which eliminates PF spasticity). Eleven subjects with hemiparesis walking at comfortable velocity and 11 controls walking at comfortable and slow velocity, underwent kinematic and PF/DF EMG analysis. Five of the hemiparetic subjects underwent tibial neurotomy &gt;1 year prior. We evaluated spasticity at rest (Tardieu scale), maximal ankle dorsiflexion, tibialis anterior agonist recruitment and gastrocnemius medialis and soleus cocontraction coefficients during swing. At slow velocity, controls (0.80±0.12 m/s) moved at a similar pace as hemiparetic subjects (0.73±0.37 m/s, NS). Hemiparetic subjects showed: (i) reduced ankle DF across swing (ii) increased PF cocontraction, including before any DF (iii) higher cocontraction despite absent spasticity in tibial neurotomy subjects (iv) higher tibialis anterior recruitment. Increased PF cocontraction occurs in the absence of spasticity or ankle DF despite higher agonist recruitment. Spastic cocontraction is a major factor limiting active DF at swing, unlike spasticity.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

Although migraine belongs to the main causes of disability worldwide the mechanisms of its pathogenesis are poorly known, which is among the reasons that this disease is underdiagnosed and undertreated. As migraine diagnosis is based on the subjective assessment of symptoms, there is a need to establish objective markers of its occurrence and severity. Tryptophan (TRP) metabolism has been associated with the pathogenesis of neurological and psychiatric disorders. In the present work, we investigated an association between migraine and the urine concentration of TRP and its metabolites 5-hydroxyindoleacetic acid (5-HIAA), kynurenine (KYN), kynurenic acid (KYNA) and quinolinic acid (QA) in 21 low-frequency episodic migraine patients and 32 controls. Migraine patients displayed lower urinary levels of 5-HIAA and KYNA, but KYN and QA were enhanced as compared with the controls. Consequently, the patients were characterized by different values of the 5-HIAA/TRP, KYN/TRP, KYNA/KYN, and KYNA/QA ratios. Furthermore, urinary concentration of 5-HIAA was negatively correlated with Migraine Disability Assessment score, monthly migraine, and monthly headache days. A negative correlation between Patient Health Questionnaire 9 scores assessing depression. In conclusion, the urinary 5-HIAA level may be an easy-to-determine marker of migraine occurrence and severity and may contribute to the identification of migraine patients with depression.

The potential of generalized machine learning models developed for crop water estimation was examined in the current study. Extreme Gradient Boosting (XGBoost), Gradient Boosting Machine (GBM), and Random Forest (RF) are three ensembled machine learning models that were developed using all of the data from a single location from 1976 to 2017 and then immediately applied at eleven different locations without the need for any local calibration. For the test period of January 2018 to June 2020, the model's capacity to estimate the numerical values of crop water requirement (Pen-man-Monteith (PM) ETo values) was assessed. In comparison to the GBM and RF models, the XGBoost model outperformed them both marginally and significantly. The estimate's weighted standard error was smaller than 0.85 mm/day, and the model's effectiveness varied from 96% to 99% across various locations. The model's strong performance was indicated by the decreased noise-to-signal ratio. A real-time water management system at the regional level can be seamlessly linked with this type of model due to its accuracy in estimating crop water requirements and its capacity to generalize.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Toward the standardization of O. biennis sprout extract (OBS-E), we aimed to obtain indicator compounds, using a validated method. HPLC-UVD allowed simultaneous quantification of indicator compounds quercetin 3-glucuronide and ellagic acid. The method was validated in terms of specificity, linearity, precision, accuracy, and limit of detection/limit of quantification (LOD/LOQ). High specificity and linearity was demonstrated, with correlation coefficients of 1.0000 for quercetin 3-glucuronide and 0.9998 for ellagic acid. The LOD/LOQ values were 0.486/1.472 μg/mL for quercetin 3-glucuronide and 1.003/3.039 μg/mL for ellagic acid. Intra-day and inter-day variability tests produced relative standard deviation for each compound of &lt;2%, a generally accepted precision criterion. High recovery rate were also obtained, indicating accuracy validation. The OBS-E prepared using various concentrations of ethanol were then analyzed. The 50% ethanol extract had highest content of quercetin 3-glucuronide, whereas the 70% ethanol extract possessed the lowest. However, the ellagic acid content was highest in the 70% ethanol extract and lowest in the 90% ethanol extract. Thus, quercetin 3-glucuronide and ellagic acid can be used industrially as indicator compounds for O. biennis sprout products, and our validated method can be used to establish indicator compounds for other natural products.

It is well established that the reaction cycles involving some halogenated alkanes (so-called ozone-depleting substances, ODS) contribute to the depletion of ozone in the stratosphere, thus causing the Montreal Protocol (initially signed in 1987) and later amendments. The Protocol called for the scheduled phase-out of ODS, including chlorofluorocarbons (CFC), hydrochloro-fluorocarbons (HCFC), carbon tetrachloride (CCl4), halon, methyl chloroform (CH3CCl3), me-thyl chloride (CH3Cl), and even hydrofluorocarbons (HFCs). In view of the urgent importance of ozone layer protection to the globally ecological environment, the Taiwan government took regulatory actions on reducing ODS consumption since 1993 by the joint-venture of the central competent authorities. Under the regulatory requirements and the industry’s efforts by adopt-ing the alternatives to ODS and abatement technologies, the phase-out of some ODS (i.e., CFC, CCl4, halon, and CH3CCl3) have been achieved prior to 2010. The consumptions of HCFCs and methyl chloride have been significantly declined over the past three decades (1993-2022). However, HFC emission indicated a V-type variation during the period. Due to the local pro-duction and extensive use of HFC in Taiwan, its emissions increased from 663 kilotons of carbon dioxide equivalents (CO2eq) in 1993 to 2,330 kilotons of CO2eq in 2001, and then decreased to 373 kilotons of CO2eq in 2011. Since then, the emissions of HFC largely used as the alternatives to ODS showed an upward trend, increasing to 1,555 kilotons of CO2eq in 2022. To be in compliance with the Kigali Amendment (KA-2015) to the Montreal Protocol for mitigating global warming, the Taiwan government has taken regulatory actions in reducing the consumption of some HFC substances with high global warming potential (GWP) under the authorization of the Climate Change Response Act in 2023, aiming at the baseline consumption in 2024 by 80 % reduction by 2045.

Quantum physics is intrinsically probabilistic. The entropy of a quantum state quantifies the amount of randomness (or information loss) of such state. The degrees of freedom of a quantum state are position and spin, and upon their specification Born's rule in phase space defines randomness. We focus on the spin degree of freedom and elucidate the spin entropy. Then, we present some of its properties and show how entanglement increases spin entropy. Some speculative predictions on the decay of the $Z^0,W^{+,-}$ gauge bosons conclude the paper.

Viruses have established symbiotic relationships with almost every other living organism on Earth and at all levels of biological organisation, from other viruses up to entire ecosystems. In most cases, peacefully coexisting with their hosts, but in most relevant cases, parasitising them and inducing diseases. Viruses are playing an essential role in shaping the eco-evolutionary dynamics of their hosts, and have been also involved in some of the major evolutionary innovations either by working as vectors of genetic information or by being themselves coopted by the host into their genomes. Viruses can be studied at different levels of biological organisation, from the molecular mechanisms of genome replication, gene expression and encapsidation, to global pandemics. All these levels are different and yet connected through the presence of threshold conditions allowing for the formation of a capsid, the loss of genetic information or epidemic spreading. These thresholds, as it occurs with temperatures separating phases in a liquid, define sharp qualitative types of behaviour. These {\em phase transitions} are very well known in Physics. They have been studied by means of simple, but powerful models able to capture their essential properties, allowing to understand them. Can the physics of phase transitions be an inspiration for our understanding of viral dynamics at different scales? Here we review well-known examples of transition phenomena in virology and their simplest mathematical modelling approaches. We suggest that the advantages of abstract, simplified pictures used in Physics are also the key to properly understand the origins and evolution of complexity in viruses. By means of several examples, we explore this multilevel landscape and how minimal models provide deep insights into a diverse array of problems. The relevance of these transitions in connecting dynamical patterns across levels and their evolutionary and clinical implications are outlined.

(1) Background: The aim of this investigation is to determine the effect of archwires’ deflection on the temperature transitions driving the austenite to martensite transformation (and vice versa) and the force released by NiTi and CuNiTi orthodontic wires. (2) Methods: Round cross-section archwires have been investigated. The calorimetric approach has been used for measuring transition temperatures occurring in the unstressed (e.g. undeflected) state of the wires. Static Thermo-mechanical analysis in a temperature controlled wet environment has been performed in the range of temperature between 5°C and 55°C for measuring temperature transitions occurring in highly deflected archwires in conjunction with the force released by these wires. (3) Results: Plateau forces investigated in Part I and those reported in the literature describes the wire’s behaviour only at deflection levels close to the end point of the force plateau extension detected at 37°C. Upon heating or cooling, the austenite finish (Af) transition temperature and the martensite start (Ms) temperature largely depends on the deflection level for both NiTi and CuNiTi. (4) Conclusions: The plateau force levels at 37°C, broadly reported in the literature, only represent the lower boundary force that a superelastic wire releases at 37°C above its elastic limit. For both NiTi and CuNiTi, plateau force levels at 37°C can be predicted by the static TMA profile matching the end point of the force plateau extension. Transition temperatures in largely deflected wires are significantly higher than those determined through the calorimetric approach.

We evaluated the immunogenicity persistence of different immunization regimens of freeze-dried human rabies vaccine (Vero cells) in the 10–60 years age group of the Chinese population. Based on phase III clinical trials of Vero cells, participants who completed the full course of immunization were continuously enrolled in four-dose trial, five-dose, and five-dose control groups. Venous blood samples were collected 12 months after completion of the full immunization for rabies virus-neutralizing antibody (RVNA) testing, and the antibody-positive rate and geometric mean concentration (GMC) were calculated. Analysis of variance was used to compare three groups. The four-dose trial, five-dose trial, and five-dose control groups included 200, 186, and 214 participants, respectively. Twelve months after full immunization, the overall RVNA-positive rates were 97.00%, 93.55%, and 94.86% in the four-dose trial, five-dose control, and five-dose trial groups, respectively. The post-immunization RVNA GMCs values were 2.50, 2.05, and 2.04 IU/mL, respectively, with no statistically significant differences between them. Twelve months after full immunization, the overall RVNA-positive rate remained high, demonstrating satisfactory immunogenicity persistence for both immunization regimens.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

Background and Objectives To compare navigator-gated three-dimensional T1-weighted gradient-echo sequences (NG-3D T1W-GRE) with standard breath-hold T1W-GRE (BH T1W-GRE) for the detection of HCC nodules in patients with chronic viral hepatitis which undergo at magnetic resonance imaging (MRI) using gadoxetic acid. Methods and materials We evaluated 58 patients with hepatic nodules at least 1 cm in diameter detected by ultrasound who underwent liver MRI including NG-3D T1W-GRE sequences and breath hold T1-weighted gradient-echo sequences with different flip angles(FA) at 10-25-40° after contrast administration of gadoxetic acid at magnetic scanner operating at1.5 Tesla. Image quality and relative hepatic and nodular enhancement were evaluated by three blinded reviewers. Results In these patients, image quality of NG-3D T1W-GRE was assessed significantly better than quality of BHT1W- GRE (P < 0.005) and relative enhancement was significantly higher than that of BH- T1W-GRE ( P

In this paper, the neural network is developed for solving the inverse photoacoustic problem aiming to estimate thermo-elastic properties and thickness of a semiconductor sample. The idea was that these sample properties be estimated from the phase characteristic because the phase measurements are more sensitive. The neural network has been trained on a large basis of photoacoustic phases calculated from a theoretical Si n-type model in the range of 20Hz to 20kHz, on which random Gaussian noise has been applied. It is shown that high accuracy and precision could be reached in solving of inverse photoacoustic problem using only phase measurement.

The aim of this study, therefore, provides information about Aflatoxin levels in raw cow’s milk in Injibara Town of Awi Administrative zone by using HPLC-FLD. A good linearity of standard calibration was found for AFM1 at a range of 0.5–7 µg/L. Regression coefficient (R2) values were 0.9999, whereas slope and intercept were 2.5278 and 0.1012, respectively. The average recoveries for the spiked samples were range from76.62– 90.98 % and the RSD values ranged between 2.55–7.36 %. The results showed that 15 % of samples (3 out of 20) were contaminated with AFM1 in the range of 0.046–0.22 µg/L. The average contamination level was 0.121 µg/L. The determined mean values of AFM1 in the collected milk samples were above the standard limit of the European Commission and lower than the level established by United States regulations. Further monitoring of Aflatoxin in milk samples from different regions of the country is justified to conclusively determine the actual safe/risks and possibly low Aflatoxins-risk milk production areas.

Guayule (Parthenium argentatum Gray) is a shrub native of the arid regions of Mexico. In the last decades, significant attention for its cultivation has risen because it is the raw material for the production of hypoallergenic natural rubber. Guayule biomass contains also high amounts of resin, which is not normally exploited in any way. Among other sesquiterpenic esters, guayulins (i.e. the parteniol esters of cinnamic acid, guayulin A, or of anisic acid, guayulin B) are contained in resin. In addition, minor amounts of guayulin C and guayulin D are formed by degradation/oxidation of guayulins A and B, respectively. Guayulins likely act as cinnamate and p-anisate reservoirs for Guayule shrub, in addition, it has been postulated that they might have a key role in the chemical defense system of Guayule. Furthermore, it seems reasonable that guayulins may possess significant biological properties (e.g. antibacterial and anticancer activities), in close analogy with those shown by sesquiterpene lactones contained in many other species of Parthenum genus. As a matter of fact, guayulins A and B play an important role in the synthesis of antineoplastics used in breast cancer treatment. In this contribution we propose an original and validated RP-HPLC approach to the simultaneous quantification of guayulins A, B, C and D. The procedure of resin extraction from Guayule biomass has been optimized in terms of both extraction method and solvent. RP-HPLC separation has been accomplished by an Ascentis^® C18 column under isocratic elution with a 80:20 (v:v) acetonitrile:water mixture. Validation was carried out in terms of limits of detection and quantification, linearity, precision, and trueness. Finally, the method was tested with a number of fresh and seasoned samples of spontaneous Guayule shrub from Mexico.

A phase 1-2, prospective, multicenter, randomized, open-label clinical trial (Code RPCEC00000382, https://rpcec.sld.cu/trials/RPCEC00000382-En/), with parallel groups, involving 1161 participants was designed to assess safety and immunogenicity of two Cuban COVID-19 vaccines (Mambisa and Abdala) in boosting COVID-19 immunity of convalescent adults after receiving one dose of either vaccine. The main safety outcome was severe vaccination adverse events occurring in &lt;5% of vaccinees. Main immunogenicity success endpoints were ≥4-fold anti-RBD IgG seroconversion or ≥20% increase in ACE2-RBD inhibitory antibodies in &gt;55% of vaccinees in Phase 1 and &gt;70% in Phase 2. Neutralizing antibody titers against SARS-CoV-2 variants were evaluated. Both vaccines were safe; no deaths or severe adverse events occurred. Mild intensity adverse events were the most frequent (&gt;73%); headache predominated for both vaccines. Phase 1 responders were 83.3% (p = 0.0018) for Abdala. Mambisa showed similar results. Phase 2 responders were 88.6% for Abdala (p &lt;0.0001) and 74.2% for Mambisa (p = 0.0412). In both phases, anti-RBD IgG titers, inhibition percentages and neutralizing antibody titers increased significantly after the booster dose. Both vaccines were safe and their immunogenicity surpassed the study endpoints.

Viral infection can regulate the cell cycle, thereby promoting viral replication. Hijacking and altering the cell cycle are important for the virus to establish and maintain latent infection. Previously, Spodoptera exigua multiple nucleopolyhedrovirus (SeMNPV) latently infected P8-Se301-C1 cells, which grew more slowly than Se301 cells and interfered with homologous SeMNNPV superinfection, were established. However, the effects of latent and superinfection with baculoviruses on cell cycle progression remain unknown. In this study, the cell cycle profiles of P8-Se301-C1 cells, and SeMNPV or Autographa californica mutiple nucleopolyhedrovirus (AcMNPV) infected P8-Se301-C1 cells were characterized by flow cytometry. The results showed that replication-related genes MCM4, PCNA, and BAF were down-regulated (p < 0.05) in P8-Se301-C1 cells and the S phase of P8-Se301-C1 cells was longer than that of Se301 cells. P8-Se301-C1 cells infected with SeMNPV did not arrest in G2/M phase and or affect the expression of Cyclin B and cyclin-dependent kinase 1 (CDK1). Furthermore, when P8-Se301-C1 cells were infected with SeMNPV after synchronized treatment with hydroxyurea and nocodazole, light microscopy and qRT-PCR analysis showed that compared with unsynchronized cells and S and G2/M phase cells, SeMNPV-infected P8-Se301-C1 cells in G1 phase induced G2/M phase arrest, and the amount of virus adsorption and intracellular viral DNA replication were significantly increased (p < 0.05). In addition, the BV production and the OB containing cells were both increased at 120 h post-infection (p < 0.05). The expression of Cyclin B and CDK1 was significantly down-regulated at 48 h post infection (p < 0.05). Finally, arrest of SeMNPV-infected G1 phase cells in the G2/M phase increased BV production (p < 0.05) and the number of OB containing cells. In conclusion, G1 phase infection and G2/M arrest are favorable to SeMNPV proliferation in P8-Se301-C1 cells, thereby alleviating the homologous superinfection exclusion. The results contribute to a better understanding of the relationship between baculoviruses and insect cell cycle progression regulation.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

The idealized rhombohedral unit cell of boron carbide is formed by a 12-atom icosahedron and a 3-atom linear chain. Phase transitions are second order and caused by the exchange of B and C sites or by vacancies in the structure. Nevertheless, the impact of such minimal structural changes on the properties can be significant. As the X-ray scattering cross sections of B and C atoms are very similar, the capability of X-ray fine structure investigation is restricted. Phonon spectroscopy helps closing this gap. Phase transitions known to date have been identified due to significant changes of properties: (1) The phase transition near the chemical composition B8C by clear change of the electronic structure; (2) The endothermic temperature-dependent phase transition at 712 K by the according change of specific heat; (3) The high-pressure phase transition at 33.2 GPa by the drastic change of optical appearance from opacity to transparency. These phase transitions affect IR- and Raman-active phonons and other solid-state properties. The phase transitions at B~8C and 712 K mean that a well-defined distorted structure is converted into another one each. In the high-pressure phase transition, an apparently well-defined distorted structure changes into a highly ordered one. In all these cases, the distribution of polar C atoms in the icosahedra plays a crucial role.

Quantum physics through the lenses of Bayesian statistics consider probabilities to be degree of believes or knowledge and subjective. A Bayesian derivation of the probability density function in phase space is presented. The entropy proposed by Geiger and Kedem \cite{GeiKed2022a,GeiKed2022b} in phase space is expanded to define quantitatively interference and entanglement. Comparisons between each of these two quantities and the entropy are made. A brief presentation of entanglement in phase space to the spin degree of freedom and to mixed states completes the work.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

Many natural signals exhibit a quasi-periodic behavior and are conveniently modeled as a combination of several harmonic sinusoids whose relative frequencies, magnitudes and phases vary with time. The waveform shape of those signals reflects important physical phenomena underlying their generation, which requires that those parameters be accurately estimated and modeled. In the literature, accurate phase estimation and modeling has received much less research effort than frequency estimation, or magnitude estimation. First, this paper addresses accurate DFT-based phase estimation of individual sinusoids in six scenarios involving two DFT-based filter banks and three different windows. It is shown that bias in phase estimation is less than 1E-3 radians when the SNR is equal to or larger than 2.5 dB. Taking as a reference the Cramér-Rao Lower Bound, it is shown that one particular window offers a performance of practical interest by approximating better the CRLB when signal conditions are favorable, and by minimizing the performance deviation when signal conditions are adverse. Second, this paper explains how a shift-invariant phase-related feature can be devised that characterizes harmonic phase structure, which motivates a signal processing paradigm that greatly simplifies parametric modeling, transformation and synthesis of harmonics signals, in addition to facilitating the understanding and reverse engineering of the phasegram. Theory and results are discussed in a reproducible perspective using dedicated experiments that are supported with code allowing not only to replicate figures and results in this paper, but also to expand research.

We study the deterministic dynamics of N point particles moving at constant speed in a 2D table made of two polygonal urns connected by an active rectangular channel, which applies a feedback-control on the particles, inverting the horizontal component of their velocities, when their number in the channel exceeds a fixed threshold. Such a bounce--back mechanism is non-dissipative: it preserves volumes in phase space. An additional passive channel closes the billiard table forming a circuit in which a stationary current may flow. Under specific constraints on the geometry and on the initial conditions, the large N limit allows nonequilibrium phase transitions between homogeneous and inhomogeneous phases. The role of ergodicity in making a probabilistic theory applicable is discussed both for rational and irrational urns. The theoretical predictions are compared with the numerical simulation results. Connections with the dynamics of feedback-controlled biological systems are highlighted.

We show that the van der Waals gas does not exhibit just the celebrated liquid-gas 1 transition but also a quantum-classical one. We study the issue with reference to the LMC statistical 2 complexity and in relation to the order-disorder contrast.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

Magnetic quantum oscillations (MQO) are traditionally applied to investigate the electronic structure of metals. In layered quasi-two-dimensional (Q2D) materials the MQO have several qualitative features giving additional useful information, provided their theoretical description is developed. Within the framework of the Kubo formula and the self-consistent Born approximation, we reconsider the phase of beats in the amplitude of Shubnikov oscillations of interlayer conductivity in Q2D metals. We show that the phase shift of beats of the Shubnikov (conductivity) oscillations relative to the de Haas - van Alphen (magnetization) oscillations is larger than expected previously and, under certain conditions, can reach the value of π/2, as observed experimentally. We explain the phase inversion of MQO during the 3D - 2D crossover and predict the decrease of relative MQO amplitude of interlayer magnetoresistance in a strong magnetic field, larger than the beat frequency.