: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Climate change is a global issue that draws widespread attention from the international society. As an important component of the climate system, the water cycle is directly affected by climate change. Thus, it is very important to study the influences of climate change on the basin water cycle with respect to maintenance of healthy rivers, sustainable use of water resources, and sustainable socioeconomic development in the basin. In this study, by assessing the suitability of multiple General Circulation Models (GCMs) recommended by the Intergovernmental Panel on Climate Change, Statistical Downscaling Model (SDSM) and Automated Statistical Downscaling model (ASD) were used to generate future climate change scenarios. These were then used to drive distributed hydrologic models (Variable Infiltration Capacity, Soil and Water Assessment Tool) for hydrological simulation of the Yangtze River and Yellow River basins, thereby quantifying the effects of climate change on the basin water cycle. The results showed that suitability assessment adopted in this study could effectively reduce the uncertainty of GCMs, and that statistical downscaling was able to greatly improve precipitation and temperature outputs in global climate mode. Compared to a baseline period (1961–1990), projected future periods (2046–2065 and 2081–2100) had a slightly decreasing tendency of runoff in the lower reaches of the Yangtze River basin. In particular, a significant increase in runoff was observed during flood seasons in the southeast part. However, runoff of the upper Yellow River basin decreased continuously. The results provide a reference for studying climate change in major river basins of China.

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

Plain lakes play a crucial role in the hydrological cycle of a watershed, but their interactions with adjacent rivers and downstream water bodies can create complex river-lake relationships, often leading to frequent flooding disasters. Taking Poyang Lake as an example, this paper delves into its interaction with the Yangtze River, revealing the spatiotemporal patterns of flood propagation within the lake and its impact on surrounding flood control measures. The aim is to provide insights for flood management in similar environments worldwide. This study employs a comprehensive approach combining hydrological statistical analysis and two-dimensional hydrodynamic modeling, based on extensive hydrological, topographic, and socio-economic data. The results indicate that the annual maximum outflow from Poyang Lake is primarily controlled by floods within the watershed, while the highest annual lake water level is predominantly influenced by floods from the Yangtze River. The peak discharge typically reaches the lake outlet within 48 hours, with the peak water level taking slightly longer at 54 hours. However, water storage in the lake can shorten the time for the peak discharge to arrive. When converging with floods from the Yangtze River, the peak water level may be delayed by up to 10 days due to the top-supporting interaction. Furthermore, floods from the "Five Rivers" propagate differently within the lake, affecting various lake regions to differing degrees. Notably, floods from the Fu River cause the most significant rise in lake water level under the same flow rate. The top-supporting effect from the Yangtze River also significantly impacts the water surface slope of Poyang Lake. When the Yangtze River flood discharge far exceeds that of the "Five Rivers" (i.e., when the top-supporting intensity f value exceeds 4), the lake surface becomes as flat as a reservoir. During major floods in the watershed, the water level difference in the lake can increase dramatically, potentially creating a "dynamic storage capacity" of up to 840 million cubic meters.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

Accurate and reliable mid-long runoff prediction (MLTRP) is of great importance in water re-sources management. However the MLTRP is not suitable in each basin and how to evaluate the applicability of MLTRP is still a question. Therefore, the total mutual information (TMI) index is developed in this study based on the predictor selection method using mutual information (MI) and partial MI (PMI). The relationship between the TMI and the predictive performance of five models is analyzed by applying five models in 222 forecasting scenarios in Australia. The results over 222 forecasting scenarios demonstrate that, compared with the MI, the developed TMI index can better represent the available information in the predictors, and has more significant negative correlation with the RRMSE with the correlation coefficient between -0.62 and -0.85. This means the model's predictive performance will become better along with the increase of TMI, and there-fore the developed TMI index can be used to evaluate the applicability of MLTRP. When TMI is more than 0.1, the available information in the predictors can support the construction of MLTRP models. In addition, the TMI is used to partly explain the difference of predictive performance among five models. In general, the complex models, which can better utilize the contained infor-mation, are more sensitive to the TMI, and have more significant improvement in terms of predic-tive performance along with the increase of TMI. This research can provide support for the study of MLTRP.

The primary objective of this study was to demonstrate the potential of digital image analysis as a tool to identify microplastic (MP) particles in surface waters and to facilitate their characterisation in terms of 2D and 3D morphology. Digital image analysis preceded by microscopic analysis was used for an exhaustive quantitative and qualitative evaluation of MPs isolated from the Vistula river. Using image processing procedures, 2D and 3D shape descriptors were determined. The Principal Components Analysis (PCA) was used to interpret the relationships between the parameters studied, characterising MP particle geometry, type and colour. This multivariate analysis of the data allowed 3 or 4 main factors to be extracted, explaining approximately 90% of the variation in the data characterising MP morphology. It was found that the first principal component for granules, flakes and films was largely represented by strongly correlated with 2D shape descriptors (area, perimeter, equivalent area diameter) and 3D shape descriptors (CSF, Compactness, Dimensionality). Considering the scraps, PC1 was represented by only five of the above descriptors, and the Compactness variable had the largest contribution to PC2. In addition, for granules, flakes and films, a relationship between 2D shape and the colour of their particles could be observed. For the most numerous MP group identified of multicoloured scraps, no such association was found. The results of our study can be used for further multivariate analysis regarding the presence of microplastic floating on the river surface, with a particular focus on particles of secondary origin. This is of key importance for optimising future efforts in conducting small-scale and multidimensional monitoring of and reducing plastics in the aquatic environment.

Unmanned aerial vehicle (UAV) photogrammetry allows the generation of orthophoto and digital surface model (DSM) rasters of a terrain. However, DSMs of water bodies mapped using this technique often reveal distortions in the water surface, thereby impeding the accurate sampling of water surface elevation (WSE) from DSMs. This study investigates the capability of deep neural networks to accommodate the aforementioned perturbations and effectively estimate WSE from photogrammetric rasters. Convolutional neural networks (CNNs) were employed for this purpose. Two regression approaches utilizing CNNs were explored: direct regression employing an encoder and solution based on prediction of the weight mask by an encoder-decoder architecture, subse-quently used to sample values from the photogrammetric DSM. The dataset employed in this study comprises data collected from five case studies of small lowland streams in Poland and Denmark, consisting of 322 DSM and orthophoto raster samples. Each sample corresponds to a 10 by 10 meter area of the stream channel and adjacent land. A grid search was employed to identify the optimal combination of encoder, mask generation architecture, and batch size among multiple candidates. Solutions were evaluated using two cross-validation methods: stratified k-fold cross-validation, where validation subsets maintained the same proportion of samples from all case studies, and leave-one-case-out cross-validation, where the validation dataset originates entirely from a single case study, and the training set consists of samples from other case studies. The proposed solution was compared with existing methods for measuring WSE in small streams using a drone. The results indicate that the solution outperforms previous photogrammetry-based methods and is second only to the radar-based method, which is considered the most accurate method available. The solution is characterized by a high degree of explainability and generalization.

A method for estimating river water surface elevation (WSE) from Landsat imagery using the river inundation area - water surface elevation (RIA-WSE) rating curve constructed from the U.S. Geological Survey Topobathymetric Elevation Model (TEM) data was developed and tested at six gauging stations along the upper Mississippi River. The Otsu's automatic threshold selection algorithm was employed for the image classification and estimation of inundation areas within each pre-defined polygon around each gauging station. In addition to the commonly used green-band based water indices, Landsat 8 and 9 OLI's ultra-blue, blue, and red band-based water indices were also tested in this study, which resulted in twenty different water indices: NDWIv (Normalized Difference Water Index), MNDWI1v and MNDWI2v (Modified Normalized Difference Water Index), AWEIsv (Automatic Water Extraction Index with shadow), and AWEInsv (AWEI without shadow), where v represents the visible light band used in the water index. At each station, about 60-80 Landsat 8 or 9 images during 2013-2023 were used for assessing the performances of the twenty water indices through comparing the estimated WSEs with the measured WSEs. Results showed that the ultra-blue or red band-based AWEIs yielded the most accurate estimations of WSEs among the twenty tested water indices.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

The aim of this research was to analyze the impact of implemented erosion control works (ECW) on soil erosion intensity in the watershed of the Ćelije reservoir (Rasina River) in the period between 1968 and 2022. The Erosion Potential Method was used to calculate the annual gross erosion (W), sediment transport (G), and erosion coefficient (Z) in the study area. As a result of the performed ECW there was a general decreasing trend in the intensity of soil erosion processes in the last 54 years. The specific annual gross erosion was 1189.12 m3/km-2/year-1 in 1968, while in 2022 it was 554.20 m3/km-2/year-1. The specific sediment transport was 540.18 m3/km-2/year-1 in 1968 and 253.55 m3/km-2/year-1 in 2022. Due to the changes in the intensity of erosion processes the specific annual gross erosion decreased by 634.92 m3/km-2/year-1, and the specific sediment transport by 286.63 m3/km-2/year-1. The erosion coefficient was reduced from Z=0.62 to Z= 0.35. A dependence between the slope of siltation and the natural bed slope was defined. The results show a significant correlation between erosion intensity and performed ECW, providing a basis for future watershed management and defining a strategy for soil erosion control in the Ćelije reservoir watershed.

Fisheries and bottom seawater data were collected in July in 2022 and 2023 from 15 sampling stations in the Huanghe River Estuary and adjacent seas in China. The patterns of functional alpha- and beta-diversity of fish communities in this area and their relationship with environmental factors were studied using trait-based analysis. Five functional classifications, which included 16 functional traits, four functional alpha-diversity indices (functional richness, functional evenness, functional divergence, and community-weighted mean), three functional beta-diversity indices (functional beta-diversity and its turnover and nestedness components), and 14 bottom environmental factors were considered. The dominant traits of fish communities were: benthivorous feeding habits, small and front-facing mouths, high trophic level, demersal, anguilliform, low growth coefficient, medium resilience, low vulnerability, and adapted to warm temperate conditions. The dominant migration traits and types of fish eggs varied by year, and fish abundance was the main factor affecting the dominant traits of the communities. The results of multiple regression on distance matrices and variance partitioning analysis indicated that ammonia nitrogen content, total phosphorus content, and pH were the main environmental factors that affected fish functional diversity. The N/P ratio had an upward control effect on fish functional diversity. Our findings also revealed that high pH gradients and distant geographical distances can inhibit trait turnover in fish communities.

The Cauto River Basin (CRB), the heartland of Cuban agriculture, has been hit hard by drought and water shortage. In response to this pressing issue, this study provides a comprehensive as-sessment of water supply, demand and balance within the Cauto River Basin, considering the baseline and projected socio-economic and climatic conditions by coupling of SWAT and WEAP models. The obtained results reveal that the annual flow in the CRB is projected to slightly de-crease (2.5%) in which the reduction in the rainy season (3.1%) is higher than that in the dry sea-son (1.3%). Total water demand in the baseline scenario is around 1.194 billion m3, dominated by agriculture (96%), with rice crop requiring nearly half. For the future scenario of 2050, the study shows a 16.6% surge in demand to 1.394 billion m3, driven by climate change and agricultural expansion. However, domestic use decreases by 10% due to population reduction. Water deficit in the future is projected to increase by 52% from 172.4 to 262.7 million m3 due to rising water demand and declining water supply. This study shows that integrating a hydrological model into a water allocation model is a promising approach to estimate the water supply, demand and balance, which is a crucial component of water resources management.

Under the extreme shortage of water resources in the Yellow River Basin, it is of great signifi-cance to analyze the spatial distribution relationship between rural settlement and water re-sources for the coordinated development of human and water resources in the Yellow River Ba-sin. However, the water allocation scheme depended on statistical data in the previous work, not on rural settlements in space. Furthermore, previous researches seldom focus on the evaluation of surface water resources accessibility according to the spatial distribution characteristics of ru-ral settlements and water resources, especially, in the Yellow River Basin and using rural set-tlement as unit. Therefore, a quantitative evaluation model of surface water resources accessibil-ity is constructed by using the GIS network analysis method, taking rural settlement as the re-search unit, based on three dimensions of topography, distance, and surface water resources, at the Yellow River basin scale. The results show that: (1) The surface runoff of rural settlement in the Yellow River basin is mostly less than 0.05 km/m2, reaching 99.83%. In other words, the Yel-low River Basin is extremely short of water resources. The surface water resources accessibility is affected by distance, topography, and surface water resources. The evaluation results show that the range of surface water resources accessibility is 0.13~0.88, with an average value of 0.47 and a standard deviation of 0.05. The High surface water resources accessibility value in the Yel-low River Basin is in the east and west, and the low value is mainly distributed in the middle. (2) The range from low to high of surface water resources accessibility in 12 catchments is Sanmen-xia station, Lanzhou station, Shizuishan station, Longmen station, Tongguan station, Toudaoguai station, Xiaolangdi station, Huayuankou station, Lijin station, Gaocun station, Ai Shan station and Tangnaihai station. (3) The value of surface water resources accessibility at the city scale is higher in the east of 10 cities and in the west of 1 city. However, it is lower in the west of 9 cities. And the values of the other cities are at a medium level. The correlation coefficient with primary industry GDP and surface water resources accessibility is 0.271 (N=56, Sig=0.043, in 0.05 level, the correlation is significant), which verifies the rationality of surface water resources accessibility model to some extent.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

The Tisza River is the longest tributary of the Danube, draining the eastern part of the Carpathian Basin (Central Europe). Five countries share its catchment with different waste production and management practices. Large amounts of waste, including macroplastics (MaPs), are washed into the river. Some of the litter is trapped by the riparian vegetation forming litter accumulations. The study aimed to map the amount of litter by a citizen science program and remote sensing data and to compare the MaP data to the amount of microplastic fragments in sediments. Volunteers reported 3216 riverine litter accumulations from five countries along the entire length of the Tisza (2016–2022). The results suggest that low flow conditions (e.g., impoundment by dams) support litter and MaP trapping. The volume of large accumulations registered by the citizens showed a good correlation with the area of drifting litter revealed on Sentinel-2 images (2015–2021) using machine learning algorithms. Though the MaPs probably fragmentate during their fluvial transport, no clear connection was found between the volume of litter accumulations and the mean microplastic fragment content of sediments (2019–2022). The “Clean Tisza Map“ reveals the high degree of stranded pollutants along rivers and supports public cleanup activities.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

Human serum albumin (HSA) corona formation at polymer microparticles of a spheroidal shape was studied using dynamic light scattering and laser Doppler velocimetry (LDV). Physicochemical characteristics of the albumin comprising, the zeta potential and the isoelectric point were determined as a function of pH for various ionic strengths. Analogous characteristics of the polymer particles were carried out. The adsorption of albumin on the particles was monitored by electrophoretic mobility measurements (LDV). The stability of the HSA functionalized particle suspensions under various pHs and their electrokinetic properties were determined. The deposition kinetics of the particles on mica, silica and gold sensors were determined in situ by optical microscopy, AFM and by the quartz microbalance (QCM) under diffusion and flow conditions. The obtained results were interpreted in terms of the coarse-grained random sequential adsorption model that allowed to estimate the range of applicability of QCM for determining deposition kinetics of virus and bacteria at abiotic surfaces.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

China’s greenhouse industry has thousands of years of development history, although the development of modern greenhouses has come late. After decades of development of China, its greenhouse industry is in the forefront of the world. China’s greenhouse industry is experiencing rapid development, transformation and upgrading. China ranks first in the world in terms of greenhouse area, used mainly for vegetable cultivation and plays an important role in the utilization of agricultural resources and food production. In 2023, the cumulative area of new greenhouses nationwide was 1835.87 million ha. In this paper we present the latest developments in the greenhouse sector. More specifically, we present a greenhouse market development overview, the greenhouse production, the greenhouse industry, and technology development. Current problems are underpinned, development opportunities and prospects are analyzed, and measures and specific proposals are detailed for the technological development of the greenhouse sector both for increasing product quantity and quality.

Anthropogenic development can strongly influence natural river processes, leading to environmental changes that negatively affect important habitats and biodiversity, and consequently reduce economically important natural resources. This study investigated the effects of salinity intrusion on the habitat of the clam Corbicula japonica in the Seomjin River estuarine zone. We employed the Environmental Fluid Dynamics Code (EFDC) model, which incorporates topographic data and hydrological changes, to simulate salinity concentrations. Two salinity measurement facilities were installed in Seomjin River estuarine and operated to optimize the EFDC model. The results show that reduced flow rates due to intake have a negligible impact on the increased salinity. Maintaining optimal salinity (15–20 psu) during neap tides at the Seomjin River Bridge requires constant high flow rates, which poses significant challenges. Saltwater stratification is identified as the primary cause of pronounced salinity stratification, particularly during neap tides. Addressing this issue through river discharge and intake facility operation is challenging. Structural measures, including riverbed restoration and underwater barriers, are recommended to improve resistance to seawater intrusion. Future research should aim to develop scenarios to reduce salinity concentrations, quantify the reduction efficiency, and propose region-specific measures.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

This study presents a novel approach for quantifying the dynamics of monthly hydraulic geometry relationships in the Jingjiang reach of the Yangtze River by integrating leaf area index (LAI) data as an indicator of riparian vegetation. A comprehensive system of ordinary differential equations (ODEs) couples traditional power-law hydraulic geometry equations with LAI, capturing the influence of erosion control on channel morphology. The periodic delayed response theory and automatic differentiation techniques are employed to enhance the modeling framework's capabilities. Calibration and verification demonstrate the models' effectiveness in capturing overall trends in discharge, width, and depth dynamics, outperforming traditional constant-parameter approaches. However, model predictive abilities are limited under extreme climate conditions due to training on normal climate data. Key assumptions, including the periodic delayed response theory's neglect of peak discharges, simplified representation of artificial cut-offs, and reliance on remotely sensed data with limited local validation, introduce uncertainties. The proposed modeling framework shows potential for broader application to other river systems with appropriate adjustments. Future research could incorporate additional environmental factors, integrate models across scales, couple with advanced simulation techniques, and expand stability assessments beyond the riverbed index. By addressing related challenges, this integrated approach lays a foundation for enhancing understanding of river morphodynamics and channel stability.

When the epipelic algae group growing on the concrete inclined side wall, which is typical of urban rivers and open diversion channels, enters the water flow, it will seriously affect the func-tion of the rivers or the channels. It is urgent to predict the transport capacity of epipelic algae group with water flow. However, the current research on the transport of pollutants is mostly based on mathematical models, and the study of the transport of flake epipelic algae group is extremely rare. A generalized hydrodynamic experimental model of a flume with sidewall epi-pelic algae group was established. Through a series of hydraulic experiments, the physical movement form and transport capacity of the suspended epipelic algae group on the side wall of the channel were studied qualitatively and quantitatively by taking the thickness, sheet size and flow rate of the epipelic algae group as the influencing factors. The key influencing factors of the suspension of epipelic algae are clarified, so as to quantitatively analyze the critical conditions of its suspension. Through flow scheduling, the probability of epipelic algae gathering some-where is increased. It provides a theoretical basis for realizing the long-distance migration of epipelic algae and optimizing the mathematical model.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

The construction time of concrete structures in hydraulic tunnels is long, the construction environment is complex, and there are many influencing factors. The requirements for construction quality are high, not only to meet the strength requirements, but also to meet the design requirements of erosion resistance, crack resistance, and seepage resistance according to its specific operating environment. Therefore, evaluating the construction quality of concrete structures in hydraulic tunnels is of great significance. Considering the randomness and fuzziness of factors affecting the construction quality of concrete structures in hydraulic tunnels, this paper proposes a comprehensive evaluation model based on Combined Weighting (CWM) and Uncertainty Measurement Theory (UM). The IAHP method and CRITIC method are used to determine the subjective and objective weights of evaluation indicators, combined weighting is based on the principle of minimum entropy, and the UM method is used to evaluate the construction quality level. Finally, taking a hydraulic tunnel as an example, its construction quality grade is calculated to be III according to the evaluation model proposed in this paper, which matches with the engineering reality, and a comparative study is made with the mixture element topology theory at the same time. It is verified that the evaluation model can scientifically and reasonably evaluate the construction quality level of concrete structures in hydraulic tunnels.

Oncomelania Hupensis is the exclusive intermediary host of Schistosoma japonicum in China. The alteration of its habitat and population distribution directly affects the safety of millions of individuals residing in the Yangtze River Economic Belt (YREB), and the ecological stability. Therefore, it is crucial to analyse the influence of climate change on the distribution of O. Hupensis in order to achieve accurate control over its population. This study utilised the MaxENT model to forecast possible snail habitats by utilising snail distribution data obtained from historical literature. The subsequent outcomes were achieved: The primary ecological factors influencing the distribution of O. Hupensis are elevation, minimum temperature of coldest month, and precipitation of wettest month; Furthermore, future climate scenarios indicate a decrease in the distribution area and a northward shift of the distribution centre for O. hupensis; Specifically, those in the upstream will move northeast, while those in the midstream and downstream will move northwest; These changes in suitable habitat area, the average migration distance of distribution centers across different climate scenarios, time periods, and sub-basins within the YREB, resulting in uncertainty. This study offers theoretical justification for the prevention and control of O. hupensis along the YREB.

Persistent land subsidence or uplift can cause serious latent hazards to urban infrastructure. To thoroughly investigate the causes and impacts of land surface deformation, this study examines the case of Wuxi City, focusing on the land fluctuation patterns in the region following the enforcement of the groundwater abstraction prohibition policy in 2005. This research utilizes the PS-InSAR technique to quantify land surface deformations in the Wuxi region from November 2015 to June 2023 and analyzes 100 SAR images to obtain comprehensive spatiotemporal evolution data of the land surface. Furthermore, this study conducts an in-depth analysis of the effects of various factors, including groundwater, precipitation, and soil geology, on the characteristics of land surface deformation. It pioneers the application of the GARCH (Generalized Autoregressive Conditional Heteroskedasticity) model to analyze the time-series displacement in the study area and innovatively introduces the "amplitude factor" index to assess land surface fluctuations. This study investigates the recent land surface deformation patterns and mechanisms in Wuxi City. By integrating the "amplitude factor", it provides a scientific foundation for future urban development and disaster mitigation strategies in Wuxi City, offering valuable insights for related research.

Pollution of sub-surface water reservoirs mainly rivers and streams through contaminated water point sources (CWPS) was studied. The objective was to formulate a discrete time delay mathematical model which describes the dynamics of reservoir pollution using mixing-problem processes that involve single species contaminants such as nitrates, phosphorous and detergents. The concentration of pollutants was expressed as a function of the inflow and outflow rates using the principle for the conservation of mass. Systems of ODEs generated from principles of mixing problems were refined into a system of DDEs so that the concentration of pollutant leaving the reservoir at time would be determined at some earlier instant, for the delay. The formulated model is a mathematical discrete time delay model which would be used to describe the dynamics of sub-surface water reservoir pollution. The results from the validation of the model were analyzed to determine how time delays in the mixing processes affect the rate of particle movement in water reservoirs.

Very heavy stratiform precipitation (> 200 mm/per day) occurred in the Hokitika region on the west coast of the South Island of New Zealand on 18 June 2015, under north-westerlies with small CAPE (< 25 J/kg). Analyses of model simulations and observations showed that this heavy rainfall was due to cold front lifting enhanced by orographic lifting over the Southern Alps. At 1.5 km grid-length, the model terrain underestimated the average height of the 103 tallest mountains over the South Island by ~ 800 m. This leads to weaker orographic lifting and mountain blocking, and a faster-moving and stronger cold front in the Hokitika region. As a result, large errors in the heavy rainfall prediction occur. By increasing either the resolved or the sub-grid mountain heights, the simulated rainfall errors were largely reduced through stronger orographic lifting and mountain blocking, and a better simulation of the cold front movement and strength. All the experiments have the same “flow-over” regime with mountain waves and/or wave breaking (Fm ranges 0.61 – 1.21). However, the rainfall amount and distribution on the windward side of mountains altered significantly. Our new findings were that the Southern Alps can have significant indirect effects on heavy rainfall by altering the speed and strength of the cold front, in addition to the well-known direct dynamical effects (i.e., orographic lifting and mountain blocking). A combination of these direct and indirect effects makes the heavy rainfall simulation sensitive to mountain heights even under the same “flow-over” regime.

This study investigated the content of macro- and microelements in the lower reaches of the Ob River (Western Siberia). Seasonal sampling was performed over a four-year period (2020-2023) during the main hydrological seasons (winter low water, spring-summer floods, and early fall low water) at three river stations. Suspended and dissolved fractions were separated by filtration through 0.45-micron nitrocellulose filters. The results revealed significant seasonal variations in the elemental content of the Ob River water, associated with changes in catchment inputs, physical and chemical conditions of the aquatic environment, and the amount and composition of incoming suspended sediment. During high water flow events in the Ob River, the concentration of suspended solids increased substantially. These included significant quantities of sparingly soluble hydrolysates such as Al, Ti, Zr, Ga. During the winter period when the Ob River was ice-covered, a 2- to 3-fold rise was observed in the concentration of Na, Mg, Ca, K, Si, Mn. Having accounted for these seasonal variations in water chemistry, we were able to refine our estimates of elemental export to the Arctic Ocean. Compared to estimates from previous studies, we observed with 2.3-fold higher dissolved loads of Mn, 2.1-fold for Zn, 1.6-fold for Fe, and 1.4-fold for Pb.

In-depth insights into the profound impacts of climate change and human activities on water resources are garnered through the dynamic changes in surface water, a crucial aspect of effective water resource management and the preservation of aquatic ecosystems. This paper introduces an innovative approach employing the random forest algorithm for the systematic extraction and monitoring of surface water at large regional or national scales. This method integrates spectral bands, spectral indices, and digital elevation model data, offering a novel perspective on this critical task. A data filling model is proposed to mitigate the impact of missing data due to cloud cover. Leveraging the capabilities of the Google Earth Engine (GEE), detailed information on surface water dynamics during the rainy and dry seasons in the Yangtze River Basin (YRB) from 1991 to 2021 is extracted using Landsat time series imagery. The analysis encompasses spatial-temporal variation characteristics and trends, with a specific focus on the intricate interplay between the areal extent of surface water and hydro-meteorological factors in each sub-basin of the YRB. Importantly, this includes considerations of potential groundwater contributions to surface water. Key findings from our research include: (1) Achieving a remarkable overall accuracy of 0.96 ± 0.03 in obtaining reliable surface water datasets with the support of GEE. (2) Identifying significant trends, such as a noteworthy increase in rainy season surface water bodies (+248.0 km2·yr−1) and a concerning decrease in surface ice/snow cover during both rainy and dry seasons, with change rates of −39.7 km2·yr−1 and −651.3 km2·yr−1, respectively. (3) Uncovering the driving mechanisms behind these changes, revealing positive correlations between the areal extent of rainy season surface water bodies and precipitation, as well as negative correlations between surface ice/snow cover area and average surface skin temperature. It is crucial to note that these driving factors exhibit variation among secondary river systems, underscoring the complexity of surface water dynamics. Furthermore, comparative analyses with existing surface water products are conducted, contributing to a deeper understanding of the advantages and uncertainties inherent in our proposed extraction method. The proposed method for large-scale surface water extraction not only enhances the monitoring of spatio-temporal surface water dynamics in the YRB but also provides valuable insights for the sustainable utilization and protection of water resources, considering the potential role of groundwater in supplementing surface water.

The European Union Water Framework Directive (2000/60/EC; WFD) aims to achieve a good ecological and chemical status of all bodies of surface water by 2027. The development of an integrated guidance on surface water chemical monitoring (e.g. WFD Guidance Document No. 7/19) has been transferred into national German law (Ordinance for the Protection of Surface Waters, OGewV). For the majority of compounds, this act requires a monthly sampling frequency to assess the chemical water quality status of a surface water body. To evaluate the representativeness of the sampling strategy under the OGewV, high-frequency online monitoring data is investigated under different sampling scenarios and compared with current, monthly grab sampling strategy. About 23 million data points were analyzed for this study, three chemical parameters (dissolved oxygen, nitrate-nitrogen, chloride concentration) and discharge data were selected from four catchment of different sizes ranging from 51391 km² to 84 km² (Elbe, Vereinigte Mulde, Neiße and two stations at Lockwitzbach). In this paper we proposed short-term online-monitoring (STOM) as a sampling alternative. STOM considers the placement of online sensors over a limited duration and return interval. In general we: (I) compare the results of conventional grab sampling with STOM, (II) investigate the different performance of STOM and grab sampling using discharge data as proxy for analyzing event-mobilized pollutants and (III) investigate the related uncertainties and costs of both sampling methods. Results show, that STOM outperforms grab sampling for parameters where minimum/maximum concentrations are required by law as the probability to catch a single extreme value is higher with STOM. Furthermore, parameters showing a pronounced diurnal pattern, like dissolved oxygen, are also captured considerably better. The performance of STOM showed no substantial improvements for parameters with small concentration variability, as nitrogen-nitrate The analysis of discharge events as a proxy parameter for event-mobilized pollutants proved that the probability of capturing samples during events is significantly increased by STOM.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

We construct a Bayesian estimator for the dilution of a wastewater sample. When wastewater is diluted by rainwater an estimate of the level of dilution is required if we are to normalise sample measurements of disease markers such as SARS-CoV-2 RNA. We consider the situation where flow measurements are available, but will regularly be unreliable because of the action of combined sewer outflows (CSOs) and wastewater storage tanks, which divert wastewater away from treatment plants when the flow is excessive. However, we also have proxies for the flow from various chemical markers (e.g.\ phosphate, ammonium, electrical conductivity), whose level per unit of population is fixed. The new flow estimator has multiple advantages compared to existing procedures: credible intervals for the estimates; optimal weighting of the chemical markers; systematic handling of missing and censored values; and model based smoothing without lags.

Autism spectrum disorder (ASD) is a neurodevelopmental disorder characterized by impairments in social interaction and communication, anxiety, hyperactivity, and restricted interest for specific subjects. In addition to the genetic factors, multiple environmental factors have been related to the development of ASD. Animal models can serve as crucial tools for understanding the complexity of ASD and identifying potential therapeutic strategies. In this study, a chemical model of ASD has been developed in zebrafish by exposing embryos to valproic acid (VPA) from 4 to 48 hours post-fertilization. After the exposure, embryos were transferred to fish water and the effects on behavior and neurotransmitters profile were analyzed at both larval and adult stages. Larvae from VPA-treated embryos showed hyperactivity and decreased visual and vibrational escape responses, as well as an altered neurotransmitters profile, with increased glutamate and decreased acetylcholine and norepinephrine levels. Adults from VPA-treated embryos exhibited impaired social behavior characterized by larger shoal sizes and a decreased interest for their conspecifics. Neurotransmitter analysis revealed a significant decrease in dopamine and GABA levels in the brain. These results support the interest of this model in the study of ASD.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Droughts have a substantial effect on water resources, agriculture, and ecosystems on a worldwide scale. In the Mekong Delta of Vietnam, droughts exacerbated by climate change are significantly endangering the region's agricultural sustainability and output. Conventional forecasting techniques frequently do not capture the intricate dynamics of meteorological phenomena associated to drought effectively, prompting the exploration of more advanced methodologies. This work utilises artificial intelligence, par-ticularly machine learning methods like Gradient Boosting and Extreme Gradient Boosting (XGBoost), to enhance drought pre-diction in the Mekong Delta. The study utilises data from 11 meteorological stations spanning from 1990 to 2022 to create and evaluate Machine Learning models based on several climatic factors. We utilise Gradient Boosting and XGBoost algorithms to estimate the Standardised Precipitation-Evapotranspiration Index (SPEI) and evaluate their effectiveness in comparison to con-ventional forecasting techniques. The results show that Machine Learning, particularly XGBoost, surpasses traditional approaches in predicting SPEI accuracy at various time scales. XGBoost demonstrates skill in understanding the complex relationships between climatic factors, with R² values falling between 0.90 and 0.94 for 1-month forecasts. The progress highlights the potential of Machine Learning in improving drought management and adaptation tactics, proposing the incorporation of Machine Learning forecasting models into decision-making processes to enhance drought resistance in susceptible areas.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

One important motivation for the implementation of the Water Framework Directive is the creation of non-market environmental benefits such as improved ecological quality, or greater opportunities for open-access river recreation via microbial pollution remediation. Pollution sources impacting on ecological or recreational water quality can be uncorrelated but non-market benefits arising from riverine improvements are typically conflated within benefit valuation studies. Using stated preference choice experiments, we seek to disaggregate these sources of value for different river users, thereby allowing decision makers to understand the consequences of adopting alternative investment strategies. Our results suggest anglers derive greater value from improvements to the ecological quality of river water, in contrast to swimmers and rowers for whom greater value is gained from improvements to recreational quality. We also find three distinct groups of respondents: a majority preferring ecological over recreational improvements, a substantial minority holding opposing preference orderings and a small proportion expressing relatively low values for either form of river quality enhancement. As such, this research demonstrates that the non-market benefits which may accrue from different types of water quality improvements are nuanced in terms of their potential beneficiaries and, by inference, their overall value and policy implications.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

The recent availability of commercial platforms for behavioral analysis in zebrafish larvae based on video-tracking technologies has exponentially increased the number of studies analyzing different behaviors in this model organism to assess neurotoxicity. Among the most commonly used assays in zebrafish larvae are basal locomotor activity (BLA) and visual motor response (VMR). However, the effect of different intrinsic and extrinsic factors that can significantly alter the outcome of these assays is still not well understood. In this work we have analyzed in 143 larvae the influence of age (5-8 days post-fertilization), time of day (8:00, 10:00, 12:00, 14:00; 16:00, 18:00, and 20:00 h), and experiment (three experiments performed at different days) on BLA and VMR results (4,004 analyses for each behavior). Results from both behaviors were adjusted to a Random-Effects linear regression model using generalized least squares (GLS), including in the model the effect of the three variables, the second-way interactions between them and the three-way interaction. The results presented in this manuscript show a specific effect of all three intrinsic factors and their interactions on both behaviors, supporting the view that the most stable time period for performing these behavioral assays is from 10:00 am to 04:00 pm, with some differences depending on age of the larva and the behavioral test.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

This study develops a structure for mapping native vegetation in a transition area between Brazilian Cerrado and Atlantic Forest from integrated spatial information from the Sentinel-1 and Sentinel-2 satellites. Most studies use this data separately, however, the integrated use of optical sensors with Synthetic Aperture Radar (SAR) sensors can improve the methodology for classifying land use and land cover (LULC). The fusion of Sentinel-1 and Sentinel-2, for example, can increase the accuracy of mapping algorithms, using complementary information, such as spectral, backscattering, polarimetry, and interferometry. The study area comprises the Lobo Reservoir Hydrographic Basin, which is part of an environmental conservation unit protected by Brazilian law and with significant human development. LULC were classified, using the random forest deep learning algorithm. The classifying attributes were backscatter coefficients, polarimetric decomposition, and interferometric coherence for radar data (Sentinel-1), and optical spectral data, comprising bands in the red edge, near infrared, and shortwave infrared (Sentinel-2). The attributes were evaluated in three settings in which the SAR and optical data were evaluated separately (C1 and C2, respectively) and in an integrated manner (C3). The study found greater accuracy for C3 (96.54%), an improvement of nearly 2% compared to C2 (94.78%) and more than 40% in relation to C1 (55.73%). The classification algorithm encountered significant challenges in identifying wetlandsin C1, but performance improved in C3, enhancing differentiation by stratifying a greater number of classes during training and facilitating visual interpretation during sampling. Accordingly, the use of SAR and optical data becomes an alternative to optimize LULC mapping in tropical regions, due to the limited influence of atmosphere on images in the microwave range.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

Selecting road networks in cartographic generalization has consistently posed formidable challenges, driving research towards the application of intelligent models. Despite previous efforts, the accuracy and connectivity preservation in these studies, particularly when dealing with road types of similar sample sizes, still warrant improvement. To address these shortcomings, we introduce a Heterogeneous Graph Attention Network (HAN) for road selection, where feature masking method is initially utilized to assess the significance of road features. Concentrating on the most relevant features, two meta-paths are introduced within the HAN framework: one for aggregating features of the same road type within the first-order neighborhood, emphasizing local connectivity, and another extending this aggregation to the second-order neighborhood, capturing a broader spatial context. For a comprehensive evaluation, we introduce a set of metrics considering both quantitative and qualitative aspects of the road network. Compared to traditional neural networks, our HAN model demonstrates superior accuracy and F1-score, particularly for road types with comparable samples. Additionally, it enhances the overall connectivity of the selected network. In summary, our HAN-based method provides an advanced solution for road network selection, surpassing previous approaches in terms of accuracy and connectivity preservation.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

Our study analyzes the ecology and distribution of fish communities related to the environmental variables of the Alto Madre de Dios River, an Andean-Amazon watershed of southern Peru, between 300 and 2811 m a.s.l. within the Manu Biosphere Reserve. We provide new ecological and diversity data for these highly unknown rivers and new data for palm swamp habitats. With electric fishing techniques, we collected a total of 1934 fish specimens belonging to 78 species, 42 genera and 15 families. To assess main patterns of diversity we combined SIMPER and ANOSIM with canonical correspondence analysis to obtain an overview of the community structure of fish and their distribution related to aquatic habitats. Our results show an important shift on fish diversity at 700 m a.s.l. separating headwater and middle-lowland communities. Electrofishing was a hindrance due to the depth, flow and low conductivity of the rivers, but also allowed us to capture fish not observed with other techniques. We also compared the use of elevation with slope as an alternative variable for statistical analysis. Our results show that slope offers a solid and equivalent explanation for fish distribution variability, avoids redundance, and instead of giving geographical data offers ecologically solid information.

Polarimetry is used to determine the Stokes parameters of a laser beam. Once all four S0,1,2,3 parameters are determined, the state of polarisation is established. Upon reflection of a laser beam with the defined S polarisation state, the directly measured S parameters can be used to determine the optical properties of the surface, which modified the S-state upon reflection. Here, we demonstrate polarimetry for the determination of surface anisotropies related to birefringence and dichroism from different materials, which have a common feature of linear patterns of different alignments and scales. It is shown that polarimetry in the back-reflected light is complementary to ellipsometry and four-polarisation camera imaging.

This study was investigate the possible hydrological impact of climate change in stream flow of Arba River based on the downscaled precipitation and temperature data at West Harerghe Zone, Oromia regional state, Ethiopia. The case study, Arba River is one of the tributaries of Awash River Basin and the catchment of the river at Bordode flow gauging station covers around 72 square kilometers. Dynamically downscaled Regional Climate Model (RCM) HIRHAM derived by ICHEC-EC-EARTH global climate model under two scenarios RCP 4.5 and 8.5 was used in this study. The future time periods are divided into two time horizons with equal length of time as the base line period 2021–2050 and 2051–2080. For both projected periods relatively the minimum average monthly percentage change in precipitation will be happened from May to October under RCP4.5 except August and from March to October under RCP8.5. The variation under RCP4.5 is relatively high when compared to RCP8.5. The average monthly per-centage of flow increment may vary from (7.6 to 81.8) for 2021-2050 and (22.3 to 107.8) for 2051-2080 under RCP4.5. Under RCP8.5 scenario, from July to January except the December for 2021-2050, simulated flow is expected to increase while from February to June decreases for both time horizons. Generally, the change of simulated flow under both scenarios and both near and far time period is follows the pattern of precipitation. However, the flow change will have less variation than the precipitation change.

The de-oxygenation process in water used in well injection operations is an important matter to eliminate corrosion in petroleum industry. This study used molecular dynamics simulations to understand the behavior of siloxane surface through studding the surface properties with two functional groups attached to the end of siloxane and their effect on de-oxygenation process. The simulations were performed using LAMMPS to characterize of surface properties. Jmol software was used to generate siloxane chains with (8, 20, and 35) repeat units. Firstly, we evaluated properties such as total energy, surface tension and viscosity. Then, we used siloxane as a membrane to compare the efficiency of de-oxygenation for the both types of functional groups. The results indicated that longer chains length increased total energy, viscosity while decreased surface tension. Replacing methyl groups with trifluoromethyl (CF3) groups increased all the above mentioned properties in varying proportions. Trifluoromethyl (CF3) groups showed better removal efficiency than methyl (CH3) groups but allowed more water to pass. Furthermore, the simulations were run using the class II potential developed by Sun, Rigby, and others within an explicit-atom (EA) model.

In the present work report, the MgAl₂O₄and the Ag/MgAl₂O₄ samples were successfully synthesized by the modified hydrothermal and the isovolumetric impregnation methods, respectively. The structural properties of the prepared samples were systematically characterized by XRD, SEM, TEM, DRS, XPS and et al techniques. The photocatalytic degradation of methylene blue by the Ag/MgAl₂O₄ and MgAl₂O₄ samples was comparatively studied under UV lamp irradiation. The results revealed that the prepared Ag/MgAl₂O₄ (pH=6) samples were the most active among the samples in photocatalytic of methylene blue. Under UV lamp irradiation, the Ag/MgAl₂O₄ (pH=6) photodegradation of methylene blue reached to 89.6% within 120 min. And the Ag/MgAl₂O₄ (pH=6) complex photocatalysts displayed a high photochemical stability under repeated irradiation. Repeated irradiate the Ag/MgAl₂O₄ (pH=6) compound, which indicated it had a high photochemical stability.

Salinity, resulting from climate change and excessive mineral fertilization, burdens farmers and negatively impacts soil and water ecosystems in the Northeastern Nile Delta. Organic and biological approaches are crucial for addressing these issues. This study examined the effects of individual and combined inoculations with cyanobacteria, yeast, and Arbuscular Mycorrhizal Fungi (AMF), with or without K-humate, on enhancing salinity tolerance, increasing yield, and improving crop quality of wheat and faba bean. The aim was to reduce NPK mineral fertilizer application rates to 25% of recommended doses. An economic evaluation was also conducted. In a preliminary laboratory experiment, the interactive effects of these microbiomes on the production of plant antioxidant enzymes and soil enzymes were investigated under salinity stress. Results showed that co-inoculation, especially with K-humate, yielded superior outcomes compared to individual inoculations. The laboratory experiment findings were confirmed by a field trial conducted in saline-alkaline soil in the Northeastern Nile Delta region. The study found that the integrated inoculation of cyanobacteria, yeast, and mycorrhizae with K-humate, along with 25% mineral NPK fertilization enhanced microbial activity, including AMF colonization, spore density, and total bacteria, cyanobacteria, and yeast counts in the plant rhizosphere. It also increased soil enzyme activity, improving soil fertility compared to individual or mineral control treatments. This integration resulted in wheat yields of 2.77 tons/ha and faba bean yields of 4.75 tons/ha. Crop quality improved, with higher levels of nitrogen, potassium, phosphorus, and protein in wheat grains and faba bean seeds. Microbiomes inoculation increased potassium uptake over sodium, enhancing the potassium/sodium ratio and salt stress tolerance. This approach reduces reliance on costly mineral fertilizers by up to 75%, enabling economically viable cultivation in marginal lands. These sustainable practices optimize resource utilization, maximize economic efficiency, and preserve natural resources.

In order to improve contrast and restore color for underwater image captured by camera sensors without suffering from insufficient details and color cast, a fusion algorithm for image enhancement in different color spaces based on contrast limited adaptive histogram equalization (CLAHE) is proposed in this article. The original color image is first converted from RGB color space to two different special color spaces: YIQ and HSI. The color space conversion from RGB to YIQ is a linear transformation, while the RGB to HSI conversion is nonlinear. Then, the algorithm separately operates CLAHE in YIQ and HSI color spaces to obtain two different enhancement images. The luminance component (Y) in the YIQ color space and the intensity component (I) in the HSI color space are enhanced with CLAHE algorithm. The CLAHE has two key parameters: Block Size and Clip Limit, which mainly control the quality of CLAHE enhancement image. After that, the YIQ and HSI enhancement images are respectively converted backward to RGB color. When the three components of red, green, and blue are not coherent in the YIQ-RGB or HSI-RGB images, the three components will have to be harmonized with the CLAHE algorithm in RGB space. Finally, with 4 direction Sobel edge detector in the bounded general logarithm ratio operation, a self-adaptive weight selection nonlinear image enhancement is carried out to fuse YIQ-RGB and HSI-RGB images together to achieve the final fused image. The enhancement fusion algorithm has two key factors: average of Sobel edge detector and fusion coefficient, and these two factors determine the effects of enhancement fusion algorithm. A series of evaluate metrics such as mean, contrast, entropy, colorfulness metric (CM), mean square error (MSE) and peak signal to noise ratio (PSNR) are used to assess the proposed enhancement algorithm. The experiments results showed that the proposed algorithm provides more detail enhancement and higher values of colorfulness restoration as compared to other existing image enhancement algorithms. The proposed algorithm can suppress effectively noise interference, improve the image quality for underwater image availably.

The pressure on freshwater resources is leading to diminishing flows in some of the critical river systems across the globe and India is no exception and this is mainly because of water withdrawal for irrigation, which is often to the tune of 70% to 80% with some proportion for domestic and industrial use. While graduating from the concept of environmental flows and its assessment methodologies in India, the water-managers, the researchers and the conservationists are now moving towards answering the next question if the rivers are to be revived, then where will the water come from, especially in the case of over-allocated rivers, including the river Ganga. While the logical way is to look at the biggest user of water, i.e. irrigation, it remains to be seen whether the irrigation water savings will actually lead to enhancing flows in a river, complementing the efforts towards maintaining e-flows in rivers, or whether it will lead to more area under agriculture, bring changes in cropping patterns towards more water-intensive crops or result in something else. This is a growing debate across the globe, where India is no exception, and there has been a wide range of opinions in this regard. This paper discusses the process, findings and lessons from a joint initiative involving farmers, the Uttar Pradesh state Irrigation and Water Resources Department, Bijnor District Administration and a conservation organisation to enhance flows in a rivulet, called karula River, which is part of the Ganga river system.

This work evaluates the surface water quality in terms of physico-chemical parameters of the Brahmani River, Odisha using statistical analysis involving the calculation of correlation coefficient and regression equation. Besides this, the work also highlights and draws attention towards the “Water Quality Index” in a simplified format which may be used at large and could represent the reliable picture of water quality. Surface water quality data is taken from OSPCB of various location i.e. Panposh D/S, Rourkela D/S, Rengali, Talcher U/S, Kamalanga D/S, Bhuban, Pattamundai and was assessed for summer, monsoon, winter for the years 2011, 2012, 2013, 2014 and 2015. Average of values, minimum of values and maximum of values of water quality parameters were obtained seasonally over the above mentioned years. Besides this, the standard deviation for the water quality parameters was also obtained for water quality parameters namely pH, Temperature, DO, TDS, Alkalinity, EC, Na+, Ca2+, Mg2+, K+, F-, Cl-, NO3-, SO42- and PO42-. Seasonal changes in various physical and chemical parameters were analysed.The values obtained were compared with the guideline values for drinking water by Bureau of Indian Standard (BIS). A systematic correlation and regression study is carried out for three seasons, showed linear relationship among different water quality parameters. This provides an easy and rapid method of monitoring water quality. Highly significant (0.8< r <1.0), moderately significant (0.6< r <0.8) and significant (0.5< r <0.6) correlations between the parameters have been worked out. High correlation coefficient has been observed between TDS,EC-Na+, Ca2+, Cl-, SO42- ; Na+- Cl-. From the collected quantities, certain parameters were selected to derive WQI for the variations in water quality of each designated sampling site. WQI of Brahmani River ranged from 36.7 to 44.1 which falls in the range of good quality of water.Panposh D/S and Rourkela D/S showed poor water quality in summer and winter season. It is shown that WQI may be a useful tool for assessing water quality and predicting trend of variation in water quality at differentlocations in the Brahmani River.

This study reports multivariate statistical techniques applied including cluster analysis to evaluate and classify the river pollution level in Taiwan, and principal component analysis-multiple linear regression (PCA-MLR) to identify the possible pollution source. Water quality and heavy metal monitoring data from Taiwan Environmental Protection Administration (EPA) was evaluated for 14 rivers in the four regions of Taiwan. The Erren River was classified as the most polluted River in Taiwan. Biochemical oxygen demand, ammonia, and total phosphate concentration in this river were the highest of the 14 rivers evaluated. In addition, heavy metal levels of the following rivers exceeded the Taiwan EPA standard limit: lead - in the Dongshan, Jhuoshuei, and Xinhuwei Rivers; copper - in the Dahan, Laojie, and Erren Rivers; and manganese - in all rivers. Water pollution in the Erren River was estimated to originate 72% from industrial sources, 16% from domestic black water, and 12% from natural sources and runoff from other tributaries. Our research showed that PCA-MLR and the cluster analysis model accomplished our study objectives and will be helpful tools to evaluate water quality in rivers and we suggest that the continuous monitoring should be conducted to monitor water pollution from anthropogenic activities.

This study investigates the concentrations of physicochemical and heavy metal contaminants in the groundwater of the Middle Awash Basin, Ethiopia, to inform targeted water management strategies. A total of 32 groundwater samples were collected from 16 stations via piezometers and boreholes at the end of both the dry (June 2021) and wet (October 2021) seasons. Utilizing Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Atomic Absorption Spectroscopy (AAS), and in situ metering, 22 physicochemical and 24 heavy metal parameters were analyzed. The data revealed significant levels of contamination; notably, sample GW11 had extraordinarily high concentrations of total dissolved solids (10,826 mg/L), strontium (908 µg/L), molybdenum (802.4 µg/L), zinc (6060 µg/L), and electrical conductivity (15,645 µS/cm), while GW12 exhibited elevated levels of aluminum (2615 µg/L), zinc (4446 µg/L), and arsenic (117.2 µg/L). Contaminants such as arsenic, vanadium, gallium, lithium, rubidium, chromium, manganese, copper, and zinc were found enriched in groundwater near Lake Beseka, influenced by agricultural runoff from sugarcane plantations and agro-industry activities. Over half of the groundwater sources were unsuitable for drinking, posing significant health risks to local communities that rely heavily on these sources due to limited access to clean surface water. The findings emphasize the urgent need for comprehensive groundwater management and remediation plans in the Middle Awash region to ensure safe and sustainable water use, particularly addressing the variation in contamination levels influenced by Lake Beseka. These measures are critical to protect public health and support local development in the face of ongoing environmental and anthropogenic pressures.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

Water-soluble nonionic surfactant, pentaethylene glycol monododecyl ether, C12E5, spontaneously blooms to the surface of spin-cast hydrophobic polyiso-prenes, generating hydrophilic surfaces. This system represents a simple model for hydrophilic chemical modification of rubbery polymers yet demonstrates surprisingly rich, complex and unexpected behaviour. The ver-tical depth profiles were quantified using neutron reflectometry (NR) and deuterated surfactant, and the surface properties were characterized using con-tact angle analysis and atomic force microscopy (AFM). Despite the low surface tension of the toluene solvent used in film preparation and the low surface en-ergy of the PI matrix, NR depth profiles revealed clear evidence of surfactant segregation. This surface layer was typically thicker than a monolayer, but incomplete, yet was remarkably stable with respect to dissolution, even when exposed to hundreds of thousands of times the volume of water required to dissolve all the surfactant on the surface. Despite the apparent resistance to removal from the surface, water exposure does alter the subsequent wettabil-ity of the surface, with a hydrophilic-to-hydrophobic transition occurring after rinsing. Complementary AFM images of these C12E5 / cis-PI films showed unexpected strand-like features on the surface of the film, which we attribute to a non-uniform lateral distribution of some of the surfactant. This surface structure becomes more evident after rinsing, and it appears that there are two distinct populations of surfactant on the PI film surface. We conclude that some of the bloomed surfactant exists as layers, which are relatively inert with respect to rinsing or surface modification, and some is laterally inhomogene-ous. This latter population is primarily responsible for surface wetting be-havior, but is not detected by specular NR.

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

Recently a new class of experiments in the field of surface gravity waves has emerged. These experiments serve as demonstration of an analogy to a broad variety of phenomena in optics and quantum mechanics. In particular, experiments involving Airy water-wave packets were carried out. The Airy wave packets have attracted tremendous attention in optics and quantum mechanics owing to their unique properties, spanning from an ability to propagate along parabolic trajectories without spreading, and to accumulating a phase that scales with the cubic power of time. Non-dispersive Cosine-Gauss wave packets and self-similar Hermite-Gauss wave packets, also well known in the field of optics and quantum mechanics, were recently studied using surface gravity waves as well. These wave packets demonstrated self-healing properties in water wave pulses as well, preserving their width despite being dispersive. Finally, this new approach also allows to observe diffractive focusing from a temporal slit with finite width.

In contrast to “frank” pathogens, like Salmonella entrocolitica, Shigella dysenteriae, and Vibrio cholerae, that always have a probability of disease, “opportunistic” pathogens are organisms that cause an infectious disease in a host with a weakened immune system and rarely in a healthy host. Historically, drinking water treatment has focused on control of frank pathogens, particularly those from human or animal sources (like Giardia lamblia, Cryptosporidium parvum, or Hepatitis A virus), but in recent years outbreaks from drinking water have increasingly been due to opportunistic pathogens. Characteristics of opportunistic pathogens that make them problematic for water treatment include: 1) they are normally present in aquatic environments, 2) they grow in biofilms that protect the bacteria from disinfectants, and 3) under appropriate conditions in drinking water systems (e.g., warm water, stagnation, low disinfectant levels, etc.) these bacteria can amplify to levels that can pose a public health risk. The three most common opportunistic pathogens in drinking water systems include Legionella pneumophila, Mycobacterium avium, and Pseudomonas aeruginosa. This report focuses on these organisms to provide information on their public health risk, occurrence in drinking water systems, susceptibility to various disinfectants and other operational practices (like flushing and cleaning of pipes and storage tanks). In addition, information is provided on a group of nine other opportunistic pathogens that are less commonly found in drinking water systems, including Aeromonas hydrophila, Klebsiella pneumoniae, Serratia marcescens, Burkholderia pseudomallei, Acinetobacter baumannii, Stenotrophomonas maltophilia, Arcobacter butzleri, and several free-living amoebae including Naegleria fowleri and species of Acanthamoeba. The public health risk for these microbes in drinking water is still unclear, but in most cases, efforts to manage Legionella, mycobacteria, and Pseudomonas risks will also be effective for these other opportunistic pathogens. The approach to managing opportunistic pathogens in drinking water supplies focuses on controlling the growth of these organisms. Many of these microbes are normal inhabitants in biofilms in water, so the attention is less on eliminating these organisms from entering the system and more on managing their occurrence and concentrations in the pipe network. With anticipated warming trends associated with climate change, the factors that drive the growth of opportunistic pathogens in drinking water systems will likely increase. It is important, therefore, to evaluate treatment barriers and management activities for control of opportunistic pathogen risks. Controls for primary treatment, particularly for turbidity management and disinfection, should be reviewed to ensure adequacy for opportunistic pathogen control. However, the major focus for the utility’s opportunistic pathogen risk reduction plan is the management of biological activity and biofilms in the distribution system. Factors that influence the growth of microbes (primarily in biofilms) in the distribution system include, temperature, disinfectant type and concentration, nutrient levels (measured as AOC or BDOC), stagnation, flushing of pipes and cleaning of storage tank sediments, and corrosion control. Pressure management and distribution system integrity are also important to the microbial quality of water but are related more to the intrusion of contaminants into the distribution system – rather than directly related to microbial growth. Summarizing the identified risk from drinking water, the availability and quality of disinfection data for treatment, and guidelines or standards for control showed that adequate information is best available for management of L. pneumophila. For L. pneumophila the risk for this organism has been clearly established from drinking water, cases have increased worldwide, and it is one of the most identified causes of drinking water outbreaks. Water management best practices (e.g., maintenance of a disinfectant residual throughout the distribution system, flushing and cleaning of sediments in pipelines and storage tanks, among others) that have been shown to be effective for control of L. pneumophila in water supplies. In addition, there are well documented management guidelines available for the control of the organism in drinking water distribution systems. By comparison, management of risks for Mycobacteria from water are less clear than for L. pneumophila. Treatment of M. avium is difficult due to its resistance to disinfection, the tendency to form clumps and attachment to surfaces in biofilms. Additionally, there are no guidelines for management of M. avium in drinking water and one risk assessment study suggested a low risk of infection. The role of tap water in the transmission of the other opportunistic pathogens is less clear and in many cases actions to manage L. pneumophila (e.g., maintenance of a disinfectant residual, flushing, cleaning of storage tanks, etc.) will also be beneficial in helping to manage these organisms as well.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

The Lower Mekong Basin has had extensive hydropower dam development, which changes hydrologic conditions and threatens the exceptional aquatic biodiver-sity. This study quantifies the degree of hydrologic change between pre-impact (1965-1968) and post-impact (2018-2021) peak hydropower development in two major tributaries of the Lower Mekong Basin, the Sekong River with the fewest dams and the Sesan River with the most dams. Both rivers historically supported migratory fishes. We use daily pre- and post-impact data and the Indicators of Hydrologic Alteration framework to evaluate streamflow changes from dam development. We found signifi-cant changes in low and high magnitude flows in the pre- and post-impact periods of dam development. For the Sekong River, minimum flow had large fluctuations that ranged 290% to 412% more than the pre-impact period, while the Sesan River ranged 120% to 160% more than pre-impact. Dry season flows increased by 200±63% on av-erage in the Sekong River, which is caused by releases from upstream dams. Mean-while, Sesan River dry season flows increased by 100±55% on average. This study in-dicates that seasonal flow changes and extreme flow events occurred more frequently in the two basins following dam construction, which may threaten the ecosystem func-tions.

The River Habitat Survey (RHS) is a method for assessing the conditions of a river channel and valley, taking into account hydromorphological factors, and assessing the degree of naturalness or the degree of anthropogenic alteration within the channel and valley based on physical and landscape data. The hypothesis tested in this study was that the quality of river habitats demonstrated using the RHS should translate into the composition of their fauna. We investigated aquatic bugs (Heteroptera Aquatica), which are a group with considerable dispersal abilities and, at the same time, composed of stenotopic species associated with a particular environment as well as of eurytopic elements inhabiting a wide range of environments (REF). The research was carried out in a small lowland river, the River Krąpiel (north-western Poland) at 6 sites with 43 sub-sites included. Our analyses suggest the RHS method can predict the composition and quality of the aquatic bug fauna inhabiting a given river. Indicators of river habitat quality (HQA and RHQ) will be associated with different habitat types depending on the geographic location and type of river, once indicating habitats associated with the mainstream river and mineral substrate (mountain and small lowland rivers) and at other times habitats covered by vegetation with relatively slow water flow (large and medium lowland rivers). Therefore, RHS may be a good method for estimating the water bug fauna, linking it to the size and character of the river.

As freshwater sources of drinking water become limited cities and urban areas must consider higher-salinity waters as potential sources of drinking water. The Salton Sea in the Imperial Valley of California has a very high salinity (43 ppt), total dissolved solids (70,000 mg/L) and color (1440 CU). Proposals to desalinate the Salton Sea are expected to lower the equilibrium salinity from 45 ppt to 3 ppt yielding significant benefits for ecological restoration. High salinity eutrophic waters such as the Salton Sea are difficult to treat yet more desirable sources of drinking water are not always available. Jar tests were performed to evaluate the treatability of Salton Sea water for potential urban water use by coagulation using aluminum chlorohydrate, ferric chloride and alum. Coagulation-sedimentation proved to be relatively ineffective for lowering turbidity with no clear optimum dose for any of the coagulants tested. Alum was most effective for color removal (28 percent) at a dose of 40 mg/L. Turbidity was removed effectively with 0.45 m and 0.1 m microfiltration. Bench tests of Salton Sea water using Sea Water Reverse Osmosis (SWRO) achieved rejections of 99 percent salinity, 97.7 percent conductivity, 98.6 percent total dissolved solids, 98.7 percent chloride, 65 percent sulfate, and 99.3 percent turbidity.

The Delaware River has made a marked recovery in the half-century since the adoption of the Delaware River Basin Commission (DRBC) Compact in 1961 and passage of the Federal Clean Water Act amendments during the 1970s. During the 1960s, the DRBC set a 3.5 mg/l dissolved oxygen criteria for the river based on an economic analysis that concluded a waste load abatement program designed to meet fishable water quality goals would generate significant recreation and environmental benefits. Scientists with the Delaware Estuary Program have recently called for raising the 1960s DO criteria along the Delaware River from 3.5 mg/l to 5.0 mg/l to protect anadromous American shad and Atlantic sturgeon and address the prospect of rising temperatures, sea levels, and salinity in the estuary. This research concludes through a marginal abatement cost (MAC) analysis that it would be cost effective to raise DO levels to meet a more stringent standard by prioritizing agricultural conservation and wastewater treatment investments in the Delaware River watershed to reduce 90% of the pollutant load 13.6 million kg/year of nitrogen (30 million lb/year) for $160 million at 35% of the $449 million annual cost. The annual least cost to reduce nitrogen loads and raise dissolved oxygen levels to meet more stringent water quality standards in the Delaware River totals $45 million for atmospheric NOX reduction, $130 million for wastewater treatment, $132 million for agriculture conservation, and $141 million for urban stormwater retrofitting. This 21st century least cost analysis estimates that $50 million/year is needed to reduce pollutant loads in the Delaware River to raise dissolved oxygen levels to 4.0 mg/l, $150 million/year is needed to reach 4.5 mg/l, and $449 million/year is needed to reach 5.0 mg/l.

In this study, the effects of grain size and gradation of riprap, overtopping flow depth and downstream slope of embankment on scouring and deposition characteristics at the downstream toe of the embankment was investigated. For the experiment, three different downstream slopes (1:2, 1:3, and 1:4), three different overflow depths (1, 2, and 3 cm), and three different sizes (d₅₀ of 16.41 mm, 8.48 mm, and 3.39 mm herein referred as No.5, 6 and 7 respectively) of riprap particles, respectively, were used in the laboratory. The experimental results demonstrated that the scour depth and deposition height increased with increasing energy head for each downstream slope condition. Among the three particle sizes, for No. 5 size particle shows the lowest scour depth and highest deposition height. For the 1:2 slope, the No. 5 particle size could resist scour 62% and 75% less than that of the No. 6 and No. 7 particles, respectively. For the 1:3 slope case, this was 31% and 46%, and for the 1:4 slope case, this was 39% and 49% less than the No. 6 and No. 7 size particles, respectively.

A recently developed thermodynamic theory for the determination of the driving force of crystallization and the crystal–melt surface tension is applied to the ice–water system employing the new Thermodynamic Equation of Seawater TEOS-10. The deviations of approximative formulations of the driving force and the surface tension from the exact reference properties are quantified, showing that the proposed simplifications are applicable for low to moderate undercooling and pressure differences to the respective equilibrium state of water. The TEOS-10 based predictions of the ice crystallization rate revealed pressure-induced deceleration of ice nucleation with an increasing pressure, and acceleration of ice nucleation by pressure decrease. This result is in, at least, qualitative agreement with laboratory experiments and computer simulations. Both the temperature and pressure dependencies of the ice–water surface tension were found to be in line with the le Chatelier–Braun principle, in that the surface tension decreases upon increasing degree of metastability of water (by decreasing temperature and pressure), which favors nucleation to move the system back to a stable state. The reason for this behavior is discussed. Finally, the Kauzmann temperature of the ice–water system was found to amount TK=116K, which is far below the temperature of homogeneous freezing. The Kauzmann pressure was found to amount pK=-212MPa, suggesting favor of homogeneous freezing upon exerting a negative pressure on the liquid. In terms of thermodynamic properties entering the theory, the reason for the negative Kauzmann pressure is the higher mass density of water in comparison to ice at the melting point.

Considering the negative impacts of climate changes along with the rapid increase in population in Islamic dominated states, e.g., the Middle East, water tension among upstream and downstream states is increasing. Despite the importance of water management in Islamic culture, the role of religion has been under-valued and under-emphasized by the scholars. The paper has sought to compare and contrast Islamic water management principles (IWMP) with international water law principles (IWLP). The findings from this analysis show not only that IWMP are in conformity with IWLP, but that in many cases, IWMP can be more effective. For instance, where international water accords between riparian states of a shared river basin are poorly developed and lack enforcement mechanisms under IWLP, those upstream states can abuse their geographical locations depriving those downstream-ers. In contrast, IWMPs stress the equitable and reasonable use of water resources among upstream and downstream users of a shared watercourse. Moreover, although IWLPs emphasize the conservation and preservation of ecosystems and the environment at the basin level, the inter-basin states especially those upstream can pose significant harm to the ecosystems. On the other side, Islam as the religion of peace, has placed much emphasis on the preservation of nature. For example, the verse, “.... And waste not by excess, for Allah loves not the wasters” [Quran, 7:31], illustrates the importance of the sustainable use of water and the environment. It is argued that if Islamic Water Management Principles are incorporated into the management instrument of Islamic States, the issue of equitable and sustainable use of water among Muslim-dominated riparian states (e.g., Iran, Afghanistan, etc.) will be solved.

The bivalve mollusc Pinna nobilis, endemic to the Mediterranean Sea, since 2016 is vanishing from the whole basin because of an infection by multiple pathogens that caused mass mortality events. In the Eastern Mediterranean some little populations seem to be resistant to the infection. These individuals could represent the only possibility for the species to recolonize now desert habitats. Thus, according to the recommendations of IUCN, the looking for living specimens of P. nobilis is a priority. As a result of a monitoring activity carried out in 2022-2024, along the Ionian cost of Apulia, in Southern Italy, the species has completely disappeared leaving only empty shells. Concurrent to the vanishing of P. nobilis, its congeneric P. rudis, resistant to the infection, seems to be taking advantage, becoming more common and colonizing habitats once exclusive of P. nobilis. In fact, from different areas of the Mediterranean, the sightings of P. rudis are increasing, together with the discovering of individuals exhibiting morphological traits that are a mixing between the two species. In some cases, these morphological features are not easy to detect, anyway the presence of these hybrids, resistant to the infection, is important for the conservation of the species.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Adaptation to climate change is being addressed in many domains. This means that there are multiple perspectives on adaptation; often with differing visions resulting in disconnected responses and outcomes. Combining singular perspectives into coherent, combined perspectives that include multiple needs and visions can help to deepen the understanding of various aspects of adaptation and provide more effective responses. Such combinations of perspectives can help to increase the range and variety of adaptation measures available for implementation or avoid maladaptation compared with adaptations derived from a singular perspective. The objective of this paper is to present and demonstrate a framework for structuring the local adaptation responses using the inputs from multiple perspectives. The adaptation response framing has been done by: (i) contextualizing climate change adaptation needs; (ii) analyzing drivers of change; (iii) characterizing measures of adaptation; and (iv) establishing links between the measures with a particular emphasis on taking account of multiple perspectives. This framework was demonstrated with reference to the management of flood risks in a case study Can Tho, Vietnam. The results from the case study show that multiple perspective framing of adaptation responses enhance the understanding of various aspects of adaptation measures, thereby leading to flexible implementation practices.

GRACE-derived Terrestrial Water Storage Anomalies (TWSA) continue to be used in an expanding array of studies to analyze numerous processes and phenomena related to terrestrial water storage dynamics, including groundwater depletions, lake storage variations, snow, and glacial mass changes, as well as floods, droughts, among others. So far, however, few studies have investigated how the factors that affect total water storage (e.g., precipitation, runoff, soil moisture, evapotranspiration) interact and combine over space and time to produce the mass variations that GRACE detects. This paper is an attempt to fill that gap and stimulate needed research in this area. Using the Nile River Basin as case study, it explicitly analyzes nine hydroclimatic and anthropogenic processes, as well as their relationship to TWS in different climatic zones in the Nile River Basin. The analytic method employed the trends in both the dependent and independent variables applying two geographically multiple regression (GMR) approaches: (i) an unweighted or ordinary least square regression (OLS) model in which the contributions of all variables to TWS variability are deemed equal at all locations; and (ii) a geographically weighted regression (GWR) which assigns a weight to each variable at different locations based on the occurrence of trend clusters, determined by Moran’s cluster index. In both cases, model efficacy was investigated using standard goodness of fit diagnostics. The OLS showed that trends in five variables (i.e., precipitation, runoff, surface water soil moisture, and population density) significantly (p<0.0001) explain the trends in TWSA for the basin at large. However, the models R2 value is only 0.14. In contrast, the GWR produced R2 values ranging between 0.40 and 0.89, with an average of 0.86 and normally distributed standard residuals. The models retained in the GWR differ by climatic zone. The results showed that all nine variables contribute significantly to the trend in TWS in the Tropical region; population density is an important contributor to TWSA variability in all zones; ET and Population density are the only significant variables in the semiarid zone. This type of information is critical for developing robust statistical models for reconstructing time series of proxy GRACE anomalies that predate the launch of the GRACE mission and for gap-filling between GRACE and GRACE-FO.

The Ijen volcano has Pleistocene age (294.00 ± 0.03 Ma), and this stratovolcano was very acidic crater water with a pH of 0-1. The acidic crater water seeps into the Banyupait river flow. Asembagus is a research area located on the northern slope of the Ijen volcano, and the Banyupait River drains this. The acidic river water flows from the Ijen Crater Lake, so the pH of the water river was very acidic. This study used several different analytic methodologies with some previous researchers, namely using the method of geological mapping, pH measurement, spectrophotometry, IRMS (Isotope Ratio Mass Spectrometer), and the technique of Induced Coupled Mass Spectrometry (ICP-MS). Besides, the petrographic analysis is used to determine the composition of rock minerals due to rocks interacting with acidic water. Banyupait River water in the Asembagus area has a pH of river water around 3-7.3, SO4 (220-683 ppm), and the type of water is meteoric water. Also, concentrations of Ca, K, Mg in the west Banyupait river irrigation water flow showed higher levels when compared to the eastern Banyupait River water flow. Likewise, REE elements from the Asembagus region showed lower concentrations compared to Ijen Crater water. This change in the level of chemical elements is caused by the acidity of the Banyupait River being diluted or mixed with water from other water. However, the spring was not affected by acidic water. The process of acidic water interaction with rocks can also be observed from rocks traversed by the Banyupait River flow. Chalcedony and hematite replace the primary minerals of basaltic rocks. This research is expected to improve the quality of water needed by the Asembagus community so that people can live healthily.

Bacteria and archaea participate in and are influenced by processes of substance circulation and energy exchanges in natural environment. Generally, the community changes of bacteria and archaea in sediment are mainly driven by seasonality in mid-latitude regions. But in our study, water diversion to Fen river played a more important role on OTU number, diversity and community structure of bacteria and archaea in sediment than seasonal variation, which was found by 16S rRNA high-throughput sequencing technology. This phenomenon might be caused by external transferred water on the physicochemical water environment and accelerated release of positive nitrogen from sediment caused by rise of water level. Changes of carbon-nitrogen cycle and increase of electrical conductivity (EC) value induced more diversion-responders than season-responders both for bacteria and archaea. Seasonal changes have been influencing bacteria and archaea mildly throughout the whole study reach. After water diversion, the environment indicators relating to bacteria community obviously changed from nutrients to salinity while that for archaea almost disappeared. Our research showed the effects of human activities on the communities of bacteria and archaea outweigh the forcing from natural seasonal changes in mid-latitude regions and revealed the mechanism, highlighting different responses of bacteria and archaea to environmental changes.

This study used a two-stage network data envelopment analysis model to measure the water use efficiency of 108 cities in the Yangtze River Economic Belt in the initial water use and wastewater treatment phases from 2009 to 2019. We used the Dagum Gini coefficient to decompose the urban water use efficiency of six major urban clusters in the Yangtze River Economic Belt. We also used σ convergence and β convergence types to test the convergence characteristics of urban water use efficiency of six major urban clusters in the Yangtze River Economic Belt. This study found that the overall low level of water use efficiency in cities in the Yangtze River Economic Zone mainly stems from the low level of water use efficiency in the wastewater treatment stage. The 108 cities in the Yangtze River Economic Zone are divided into four types based on the average values of water use efficiency in the initial use and wastewater treatment phases; the highest number of cities are in the double-low category, with low average values of water use efficiency in the initial use and wastewater treatment phases. During the study period, spatial differences in urban water use efficiency in the Yangtze River Economic Zone narrowed, with the differences stemming mainly from hyperdensity, followed by intra- and inter-regional differences. Meanwhile, there is convergence in urban water use efficiency in the Yangtze River Economic Belt; significant β convergence in the urban agglomerations of the Yangtze River Delta, Jianghuai, middle reaches of the Yangtze River, Chengdu–Chongqing, and Central Yunnan; and insignificant β convergence in the Central Qian urban agglomeration. After considering control factors, such as industrial structure, financial development level, environmental regulation, economic development level, and science and education development level, the water use efficiency of the six major urban clusters in the Yangtze River Economic Belt converges faster, but the influence of these control factors on the water use efficiency of each urban cluster is heterogeneous. Research results have reference value for the development of improvement strategies on differentiated urban water use efficiency in the Yangtze River Economic Belt.

Estimates of extreme water level return periods in river systems are crucial for hydraulic engineering design and planning. Recorded historical water level data of Taiwan’s rivers are not long enough for traditional frequency analyses when predicting extreme water levels for different return periods. In this study, the integration of a one-dimensional flash flood routing hydrodynamic model with the Monte Carlo simulation was developed to predict extreme water levels in the Danshuei River system of northern Taiwan. The numerical model was calibrated and verified with observed water levels using four typhoon events. The results indicated a reasonable agreement between the model simulation and observation data. Seven parameters, including the astronomical tide and surge height at the mouth of the Danshuei River and the river discharge at five gauge stations, were adopted to calculate the joint probability and generate stochastic scenarios via the Monte Carlo simulation. The validated hydrodynamic model driven by the stochastic scenarios was then used to simulate extreme water levels for further frequency analysis. The design water level was estimated using different probability distributions in the frequency analysis at five stations. The design high-water levels for a 200-year return period at Guandu Bridge, Taipei Bridge, Hsin-Hai Bridge, Da-Zhi Bridge, and Chung-Cheng Bridge were 2.90 m, 5.13 m, 6.38 m, 6.05 m, and 9.94 m, respectively. The estimated design water levels plus the freeboard are proposed and recommended for further engineering design and planning.

226Ra and 228Ra are typically monitored for groundwater and surface water compliance at legacy U mining and milling sites. Groundwater monitoring results for combined Ra (226Ra+228Ra) reported by the existing contract laboratory at a former U mine and mill Site (Wyoming, USA) have been highly variable and with increasing trends at the Site compliance and background wells since the method was changed in 2005. Sample reanalysis has indicated poor reproducibility and significant analytical error in 228Ra measurements. An interlaboratory comparison was conducted to evaluate the potential causes of the high variability and analytical error. Two different methods were used for 226Ra (M903.0 and M903.1) and 228Ra (M904.0 and Ra-05). 226Ra results were less variable compared to 228Ra, and 228Ra data from the existing laboratory were qualified as estimated with high bias due to detection of 228Ra in the field blank. Compliance with the 226Ra+228Ra groundwater standard was either met or not met, depending on which laboratory conducted the analyses. Specific laboratory techniques, rather than the analytical method, are contributing to elevated 228Ra values being reported. It was recommended that samples whose 226Ra+228Ra results exceed the Site standard in the future be reanalyzed by the existing laboratory with a sample split also being sent to an outside laboratory for confirmatory analysis.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

This study innovatively assesses the Mun River flow components in Thailand, integrating Artificial Neural Networks (ANN) and Isotopic (18O) End-Member Mixing Analysis (IEMMA). It quantifies the contributions of the Upper Mun River (UMR) and Chi River (CR) to the overall flow, revealing a discrepancy in their estimated contributions. ANN predicts the UMR and CR contribute approximately 70.1% and 29.5% respectively, while IEMMA indicates a more pronounced disparity with 84% from UMR and 16% from CR. This divergence highlights the distinct perspectives of ANN, focusing on hydrological data patterns, and IEMMA, emphasizing isotopic signatures. Despite discrepancies, both methods validate UMR as a significant contributor to the overall flow, highlighting their utility in hydrological research. The findings underscore the complexity of river systems and advocate for an integrated approach of river flow analysis for a comprehensive understanding, crucial for effective water resource management and planning.

Surface velocity is traditionally measured with in situ techniques such as velocity probes (in shallow rivers) or Acoustic Doppler Current Profilers (in deeper water). In the last years, researchers have developed remote sensing techniques, both optical (e.g., image-based velocimetry techniques) and microwave (e.g., Doppler radar). These techniques can be deployed from Unmanned Aerial Systems (UAS), which ensure fast and low-cost surveys also in remotely-accessible locations. We compare the results obtained with a UAS-borne Doppler radar and UAS-borne Particle Image Velocimetry (PIV) in different rivers, which presented different hydraulic–morphological conditions (width, slope, surface roughness and sediment material). The Doppler radar was a commercial 24 GHz instrument, developed for static deployment, adapted for UAS integration. PIV was applied with natural seeding (e.g., foam, debris) when possible, or with artificial seeding (woodchips) in the stream where the density of natural particles was insufficient. PIV reconstructed the velocity profile with high accuracy typically in the order of a few cm s⁻¹ and a coefficient of determination (R²) typically larger than 0.7 (in half of the cases larger than 0.85), when compared with acoustic Doppler current profiler (ADCP) or velocity probe, in all investigated rivers. However, UAS-borne Doppler radar measurements show low reliability because of UAS vibrations, large instrument sampling footprint, large required sampling time and difficult-to-interpret quality indicators suggesting that additional research is needed to measure surface velocity from UAS-borne Doppler radar.

Climate simulations in West Africa have been attributed with large uncertainties. Global climate projections are not consistent with changes in observations at the regional or local level of the Niger basin, making management of hydrological projects in the basin uncertain. This study evaluates the potential of using the quantile mapping bias correction to improve the Coupled Model Intercomparison Project (CMIP5) outputs for use in hydrology impact studies. Rainfall and temperature projections from 8 CMIP5 Global Climate Models (GCM) were bias corrected using the quantile mapping approach. Impacts of climate change was evaluated with bias corrected rainfall, temperature and potential evapotranspiration (PET). The IHACRES hydrological model was adapted to the Niger basin and used to simulate impacts of climate change on discharge under present and future conditions. Bias correction significantly improved the accuracy of rainfall and temperature simulations compared to observations. Nash coefficient (NSE) for monthly rainfall comparisons of 8 GCMs to the observed was improved by bias correction from 0.69 to 0.84. The standard deviations among the 8 GCM rainfall data were significantly reduced from 0.13 to 0.03. Increasing rainfall, temperature, PET and river discharge were projected for all GCMs used in this study under the RCP8.5 scenario. These results will help improving projections and contribute to the development of sustainable climate change adaptation strategies.

Reservoir routing has been a routine procedure in hydrology, hydraulics and water management. It is typically based on the mass balance (continuity equation) and a conceptual equation relating storage and outflow. If the latter is linear, then there exists an analytical solution of the resulting differential equation, which can directly be utilized to find the outflow from known inflow, and to obtain macroscopic characteristics of the process, such as response and residence times, and their distribution functions. Here we streamline the reservoir routing framework and extend it to find approximate solutions for nonlinear cases. The proposed framework can also be useful for climatic tasks, such as describing the mass balance of atmospheric carbon dioxide and determining characteristic residence times, which have been an issue of controversy. Application of the theoretical framework results in excellent agreement with real world data. In this manner, we easily quantify the atmospheric carbon exchanges, and obtain reliable and intuitive results, without the need to resort to complex climate models. The mean residence time of atmospheric carbon dioxide turns out to be no more than four years and the response time is smaller than that, thus opposing the much longer mainstream estimates.

Using a detailed atmospheric radiative transfer model, we derive macroscopic relationships of downwelling and outgoing longwave radiation, useful for hydrological practice. We validate them using empirical formulae based on downwelling radiation data, which are in common use in hydrology, as well as satellite data for the outgoing radiation. We use the macroscopic relationships to infer the relative importance of carbon dioxide and water vapour in the greenhouse effect. The results show that the contribution of the former is 4% – 5%, while water and clouds dominate with a contribution of 87% – 95%. The minor effect of carbon dioxide is also confirmed by the small, non-discernible effect of the recent escalation of atmospheric CO2 concentration from 300 to 420 ppm, which is quantified at 0.5% for both downwelling and outgoing radiation. Water and clouds also perform other important functions in climate, such as regulating the heat storage and the albedo, as well as cooling the Earth’s surface though latent heat transfer, with a contribution of 50%. By confirming the major role of water on climate, these results suggest that hydrology should have a more prominent and more active role in climate research.

The escalation of mining activities in the karst regions of Guizhou Province has heightened the occurrence of water-inrush incidents in deep coal mines. This study focused on water-inrush phenomena within the Xinhua mining area of Jinsha County, Guizhou Province, aiming to investigate the sources of these incidents. The findings indicated that the overlying limestone of the Changxing Formation in the coal seam served as a vulnerable aquifer under certain conditions, leading to water inrushes. The analysis of the spatiotemporal distribution patterns of water-inrush incidents at the working face indicated that previous mining operations damaged the shallow Changxing Formation limestone, resulting in the accumulation of goaf water and the formation of numerous mining-induced fractures. These fractures served as rapid conduits for water inrushes from both atmospheric precipitation and underground sources at the deep working face. The examination of surface water and mine water quality demonstrated that both exhibited similar characteristics, predominantly featuring bicarbonate, sulfate, and sodium compositions. Investigation into the relationship between mine water inflow and atmospheric precipitation established that atmospheric precipitation influenced the mine water supply cycle, with a replenishment period of ~10 months during the operational phase of the Jinyuan Coal Mine and about one month post-closure. The fractures induced by mining activities within the Changxing Formation limestone facilitated water flow, with atmospheric precipitation serving as the primary water source for the mine. This study offered a valuable scientific foundation for addressing water-related damage resulting from atmospheric precipitation in mines susceptible to water inrushes under analogous hydrogeological conditions.

The impact of antecedent soil moisture content on soil erosion is a complicated phenomenon, which is still under argument with contradictions in research results. Hence, the objective of this study is to investigate the impact of antecedent soil moisture content to soil loss on clay soil by conducting two-year field experiments under natural rainfall on runoff plots with length of 10 meters, width of 3 meters, and uniform slope of 9%. Volumetric soil moisture sensors were used to log soil moisture changes, and soil moisture readings were used along with rainfall records to quantify the antecedent soil moisture conditions for each rainfall event. Results of this study show duration of the effective erosion event outranks the antecedent volumetric soil moisture content. Field study also suggests that accumulative rain falling within 48 hours (Pp48) prior to an effective erosion event strongly correlated with soil loss per Rainfall-Runoff Erosivity Index (Soil Loss / EI30), particularly when the duration of an effective erosion event is either between 3 ~ 7 hours or 10~ 30 hours. Hence, Pp48 can be considered as an alternative to replace antecedent soil moisture content in RUSLE 2’s cover and management factor.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

This paper evaluated the quality and suitability of surface water in the Vaalharts area, South Africa, for human consumption, drinking, and irrigation purposes. Water quality constituents include water pH, EC, TDS, HCO3-, Cl-, SO4, Mg, Ca, k, Na, NO3, F, Fe, PO4, As, Al, Mn, Cr, Cu, Zn, B, Cd, Hg, Pb, N, Sb, Se, and the biological parameter included E. coli along surface waters as well as canals and dams. Sodium Adsorption Ratio, Sodium Percentage, Permeability Index, Residual Sodium Carbonate, Kelley’s Ratio, Magnesium Hazard, and Potential salinity irrigation water parameters indicated that the majority of the water samples are suitable for irrigation. The water quality index values showed that the majority of the samples are unsuitable for drinking but suitable for irrigation and industrial uses. E. coli in the surface water samples in the study area show unsafe water quality with high and very high risk for human health. Based on the classifying criterion of the Heavy Metal Pollution Index and Heavy Metal Evaluation Index, all the water samples are above the critical limit, therefore, unsuitable for human consumption. The carcinogenic risk (CR) concentrations of As, Cr and Cd were above the target risk.

To address three important issues related to extraction of water features from Landsat imagery, i.e., selection of water indexes and classification algorithms for image classification, collection of ground truth data for accuracy assessment, this study applied four sets (ultra-blue, blue, green, and red light based) of water indexes (NWDI, MNDWI, MNDWI2, AWEI_ns, and AWEI_s) combined with three types of image classification methods (zero-water index threshold, Otsu, and kNN) to 24 selected lakes across the globe to extract water features from Landsat-8 OLI imagery. 1440 (4x5x3x24) image classification results were compared with the extracted water features from high resolution Google Earth images with the same (or ±1 day) acquisition dates through computing the Kappa coefficients. Results show the kNN method is better than the Otsu method, and the Otsu method is better than the zero-water index threshold method. If the computational cost is not an issue, the kNN method combined with the ultra-blue light based AWEI_ns is the best method for extracting water features from Landsat imagery because it produced the highest Kappa coefficients. If the computational cost is taken into account, the Otsu method is a good choice. AWEI_ns and AWEI_s are better than NDWI, MNDWI and MNDWI2. AWEI_ns works better than AWEI_s under the Otsu method, and the average rank of the image classification accuracy from high to low is the ultra-blue, blue, green, and red light-based AWEI_ns.

This study examines the environmental challenges faced by Malaysian industries in adhering to industrial effluent regulations with the research question, what are the challenges in complying with environmental legislations from industries? It investigates the primary factors contributing to non-compliance and the perspectives, knowledge, and needs of Malaysian industries regarding environmental compliance. This study recommends the best strategy for promoting self-compliance. Thirteen stakeholders from various industries with environmental management experience were interviewed. Over the past seven years, these industries have shown low com-pliance with the Industrial Effluent Regulation 2009, prompting an exploration of their adaptability to regulations. Challenges identified include cost, employee attitudes, technology, management support, public complaints, and jurisdictional issues. Responses varied from divergent to unified viewpoints, highlighting the complexity of compliance issues. Respondents suggested enhancing compliance through behavioral changes, including incentives, enforcement, awareness, guidance, industry ratings, management commitment, and public disclosure of emissions. Suggestions for improvement and innovative solutions emerged based on participants' experiences, emphasizing the importance of continuous improvement. The study emphasizes the government's crucial role in ensuring regulation adherence but underscores the need for analyzing barriers and exploring alternative approaches. Understanding industry perspectives and strategies is essential for progress. Compliance, however, requires an analysis of the current challenges and adopting adaptive measures. It is important to understand industries' perspectives and strategies to move forward.

Soil erosion due to soil erosion is an important ecological impact factor. In order to further explore the impact and contribution of soil and water conservation measures on sand production and transport in the watershed, and also to provide a reference for soil erosion control, soil and water conservation and ecological environmental protection in the Yellow River Basin. In this paper, based on the measured data from the Henan Soil and Water Conservation Observatory in the Yellow River Basin, we select appropriate equations for quantifying soil erosion factor to calculate the rainfall erosion, topography, soil, vegetation and soil conservation measures in the basin, and then analyse the changes in soil erosion factor and the actual benefits of soil conservation measures in the basin. The results show that there is an increasing trend in the rainfall erosion force factor R in the Yellow River Basin; Soil erosion can be K value made the vertical loess > yellow clunamon soil, the overall change shows a decreasing trend, indicating that erosion control has produced results and that attention should be paid to erosion control in the lithosol region in the future; Since the slope lengths of the runoff plots are laid out consistently with the same LS values for both topographic factors, soil erosion is severely increased when the slope exceeds 20°. The C value of natural vegetation is small, while the C value of bare land is large. The authorities should continue to promote the return of farmland to forests and grasses and pay attention to the self-regulation and restoration of ecosystems; There is an overall decreasing trend in the P value of the soil and water conservation measures factor, the soil and water conservation measures have been effective in providing good protection.

The Yamuna River in Delhi is a prevalent epitome of the depleted ecosystem that has transformed into a sewage drain due to intense pollution and blooming anthropogenic pressure. As a leading polluter, Delhi contributes to more than 70% of Yamuna's pollution load. Its drains discharge a massive B.O.D. load daily into the river, making it severely polluted, as reflected by the water quality index. The paper uses secondary data to analyze the parameters to determine the water quality of Yamuna at different monitoring sites. It performs correlation analysis to determine the relationship among factors contributing to river water pollution. The results of correlation analysis suggest a highly significant association between parameters COD-BOD, but the association is mild to a minimum among other parameters such as BOD-DO, BOD-pH, COD-DO, COD-pH and DO-pH. Most parameters were observed to be above the hazardous level acceptable for using river water. The analysis of S.T.P.s indicates the need to increase the capacity in terms of treatment, storage, reopening of closed plants and efficient operation to meet the increasing demand for fresh Water. Also, there is a need to create demand for wastewater in different sectors of urban areas like construction, horticulture, industrial coolants, etc.