In order to improve the stiffness of the flexible robot,this paper proposes a variable-stiffness elastic actuator to improve the rigidity of flexible robots. The actuator integrates the working principles of a pneumatic drive, wedge structure, and particle blockage. the tensile stiffness of the actuator is nonlinearly negatively correlated with the air pressure because of the structural and material properties.The compressive stiffness and lateral stiffness increases nonlinearly as air pressure increases, being 3and 121 times greater at 0.17 MPa compared to 0 MPa, respectively. Beyond 0.17 MPa, the two stiffness of the actuator experiences incremental growth due to wedge impedance forces.

The use of haptic devices in rehabilitation of impaired limbs has become rather popular, given the proven effectiveness in promoting recovery. In a standard framework, such devices are used in rehabilitation centers, where patients interact with virtual tasks, presented on a screen. To track their sessions, kinematic/dynamic parameters or performance scores are recorded. However, as Internet access is now available at almost every home, and in order to reduce the hospitalization time of the patient, the idea of doing rehabilitation at home is gaining wide consent. Medical care programs can be synchronized with the home rehabilitation device; patient data can be sent to the central server that could redirect to the therapist laptop (tele-healthcare). The controversial issue is that the recorded data do not actually represent the clinical conditions of the patients according to the medical assessment scales, forcing them to frequently undergo clinical tests at the hospital. To respond to this demand, we propose the use of a bilateral master/slave haptic system that could allow the clinician, who interacts with the master, to assess remotely and in real time the clinical conditions of the patient that uses the home rehabilitation device as the slave. In this paper, we describe a proof of concept to highlight the main issues of such an application, limited to one degree of freedom, and to the measure of the stiffness and range of motion of the hand.

Rotation motion in a three-dimensional physical world refers to an angular displacement of an object around a specific axis in $\mathbb{R}^3$. It is typically formulated as a non-linear and non-convex process due to the nonlinearity and nonconvexity of $\mathbb{SO}(3)$. However, this paper proposes a new perspective that the 3D rotation motion can be expressed by the linear equation without dropping any constraints and increasing any singularities. Moreover, two frequent cases, i.e., $\angle\left(\mathbf{R}\boldsymbol{x},\boldsymbol{y}\right)=0(\pi)$ and $\angle\left(\mathbf{R}\boldsymbol{x},\boldsymbol{y}\right)=\frac{\pi}{2}$, in computer vision and robotics that can be expressed linearly are deeply discussed in this paper.

Observation of parity-violating effects in chiral molecules is a long-standing challenge of the molecular spectroscopy community. In the microwave regime, the difference in transition frequencies between enantiomers is predicted to be below the mHz level, which is considerably beyond current experimental capabilities. The most promising future efforts combine vibrational spectroscopy, buffer gas cooling, and carefully chosen molecular candidates with large predicted parity-violating shifts. Here, we demonstrate for the first time high-precision differential microwave spectroscopy, achieving sub-Hz precision by coupling a cryogenic buffer gas cell with a tunable microwave Fabry-Perot cavity. We report statistically limited sub-Hz precision of (0.08±0.72) Hz, observed between enantiopure samples of (R)-1,2-propanediol and (S)-1,2-propanediol at frequencies near 15 GHz. We confirm highly repeatable spectroscopic measurements compared to traditional pulsed-jet methods, opening up new capabilities in probing subtle molecular structural effects at the 10−10 level and providing a platform for exploring sources of systematic error in parity-violation searches. We discuss dominant systematic effects at this level and propose possible extensions of the technique for higher precision.

An analysis of the stiffness theory reveals that coal mass compression bumps occur only when both the failure criterion and the stiffness criterion are simultaneously satisfied. Then a new structural factor called uneven stiffness coal seam structure (USCS) is proposed, which consists of an uneven stiffness coal seam along with continuous roof and floor. The USCS serves the dual functions of pressure concentration and stiffness reduction. The former facilitates stress concentration from the low stiffness zone (LSZ) to the high stiffness zone (HSZ), thus raising the risk (rF) of failure. The latter reduces the stiffness of the surrounding rock of the HSZ, allowing the system to meet the stiffness criterion even with a hard roof, thereby reconciling the contradiction between the stiffness theory and engineering experience and raising the risk (rI) of instability. The HSZ of the USCS, including thinning zones, bifurcating areas, magmatic intrusion areas, and remnant pillar affected areas, is more susceptible to coal bump incidents than a conventional coal seam. Mechanical analysis and simple numerical simulations validate the pressure concentration and stiffness reduction functions of the USCS. The results demonstrate the following: 1) The normal stress of the HSZ positively correlates with ER, HR, KH, and SL, but negatively correlates with KL and SH; The stiffness of surrounding rock of the HSZ negatively correlates with HR, KH, SL, and SH, but positively correlates with ER and KL. 2) Failures within the HSZ of the USCS enables the roof strata to release bending deformation energy without undergoing fracturing. 3) The alignment between the HSZ of an existing USCS and the HSZ of an artificial USCS advancing with the working face intensifies stress concentration and reduces stiffness, thereby significantly increases the risk (rCB) of coal bump. By applying the stiffness theory and relevant USCS findings, new explanations can be provided for engineering phenomena such as the time-delayed coal bumps, the inefficient pressure relief in ultra thick coal seams, and the “microseism deficiency” observed prior to certain coal bumps.

The paper presents construction, laboratory tests as well as the first field application of a new fiber-optic rotational seismograph. The system based on fiber-optic gyroscope (FOG) with determined Angle Random Walk of the order of 10-8 rad/Sqrt(s) and a few rad/s maximum detectable amplitude of rotation in the frequency range from DC to 328.12 Hz. It has been designed for rotational seismology area of interest. This work also presents exemplary relevant measurements which were conducted using a set of two devices installed in the geophysical observatory in Książ, Poland.

The magnetic field of the earth plays an important role in the ecosystem, and the magnetic field of celestial bodies is also important in the formation of cosmic large-scale structures, but the origin and evolution of the celestial magnetic field is still an unresolved mystery. Many hypotheses to explain the origin have been proposed, but there are some insurmountable difficulties for each one. At present, the theory widely accepted in scientific society is the dynamo model, it says that, the movement of magnetofluid inside celestial bodies, which can overcome the Ohmic dissipative effect and generate persistent weak electric current and macroscopic magnetic field. However, this model needs an initial seed magnetic field, and the true values of many physical parameters inside the celestial body are difficult to obtain, and there is no stable solution to the large range of fluid motion. These are all difficulties for the dynamo model. Furthermore, it is difficult for the dynamo to explain the correlation between the dipole magnetic field and angular momentum of a celestial body. In this paper, by calculating the interaction between spin of particles and gravity of celestial body according to Clifford algebra, we find that a rotational celestial body provides a field $\Omega^\alpha$ for spins, which is similar to the magnetic field of a dipole, and the spins of charged particles within the celestial body are arranged along the flux line of $\Omega^\alpha$, then a macroscopic magnetic field is induced. The calculation shows that the strength of $\Omega^\alpha$ is proportional to the angular momentum of the celestial body, which explains the correlation between the magnetic intensity and angular momentum. The results of this paper suggest that further study of the effects of internal variables such as density, velocity, pressure and temperature of a celestial body on $\Omega^\alpha$ may provide some new insights into the origin and evolution of celestial magnetic field.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

In an effectively managed grazing system, goats as grazers can benefit the land's physical, chemical, biological, and economic aspects. However, little research has evaluated rotational and continuous goat grazing in Kentucky. This observational study investigated the impact of rotational and continuous grazing on forage production and goat performance. One group of 10 does was placed on a rotational pasture, and another group of 10 does were placed on a continuous pasture, each pasture measuring two acres. The pastures were side-by-side with similar forage types and compositions. Goat performance was measured by body weight and eye color score (FAMCHA). Forage production was measured weekly by collecting forage heights at three random spots in each pasture. The rotational grazing field displayed a more evenly grazing pattern, while the continuous field experienced overgrazing in some areas and overgrown of the less desired forage. Goats on the continuous field had a decrease in body weight, while the weights were more consistent in the rotational grazing field. The FAMACHA score was temporarily reduced on the rotational grazing pasture, indicating that properly managed rotational grazing may prevent anemia, possibly by reducing the shedding of gastrointestinal parasites. However, due to drought and lack of forage, the FAMACHA score of goats in the rotational grazing system reverted to its original status by the end, indicating that more extensive management and timely adjustments are necessary to ensure optimal goat performance. Our results suggest that rotational grazing may support more consistent forage yields and body weights of goats and has the potential to reduce the incidence of anemia and parasitic infestations in goats in Kentucky.

Accurate image registration is essential for eye movement compensation in optical coherence tomography (OCT) and OCT angiography (OCTA). The spatial resolution of an OCT instrument is typically anisotropic, i.e., different resolutions in the lateral and axial dimensions. When OCT images have anisotropic pixel resolution, residual distortion (RD) and false translation (FT) were always observed after image registration for rotational movement. In this study, RD and FT were quantitively analyzed over different degrees of rotational movement and various lateral and axial pixel resolution ratio (RL/RA) values. The theoretical analysis confirmed that the RD and FT increase significantly with the rotation degree and RL/RA. An image resizing assisting registration (RAR) strategy was proposed for accurate image registration. The performance of direct registration (DR) and RAR for retinal OCT and OCTA images were quantitatively compared. Experimental results confirmed that unnormalized RL/RA causes RD and FT, RAR can effectively improve the performance of OCT and OCTA image registration and distortion compensation.

In a previous series of papers relating to the Combined Gravitational Action (CGA), we have exclusively studied orbital motion without spin. In the present paper, we apply CGA to any self-rotating material body, i.e., an axially spinning massive object, which itself may be locally seen as a gravito-rotational source because it is capable of generating the gravito-rotational acceleration, which seems to be unknown to previously existing theories of gravity. The consequences of such an acceleration are very interesting, particularly for Compact Stellar Objects. Independently of the equation of state, it is found that the minimum radius of a stable neutron star is three times its gravitational radius, R_min = 3GM_NS/c², and its critical and maximum internal magnetic field strength cannot exceed the value of 3×10¹⁸ G.

Fouling by activated sludge in membrane bioreactor (MBR) processes for wastewater treatment can be reduced using several strategies such as backflushing, relaxation, and chemical cleaning. Some proprietary systems such as Avanti’s RPU-185 Flexidisks MBR use novel circular rotating, flat sheet membranes to assist in limiting this fouling. An attempt has already been made to model this novel rotating fouling process by developing a simulation model based on first principles and traditional fouling mechanisms. In order to directly compare the potential benefits of rotational MBR system, a follow-up study was carried out using Avanti’s newly developed static (non-rotating) Flexidisks MBR system. This new process uses the same proprietary and patented membrane modular arrangement as used in the circular rotational unit, but is configured instead as a static square-shaped unit which is in-line with the more traditional and popular format used for submerged flat sheet MBR systems. During this study, the results from operating the static pilot unit were simulated and modelled using a standard fouling model coupled with a viscosity to mixed liquor relationship model. These results were then compared with those obtained from running the rotating MBR model however with rotational switching functions turned off and rotational parameters set to a static mode. This comparison was done to ascertain whether the basic premise of the developed rotational model was sound in empirical terms when compared to a standard MBR flux model. The study concluded that relatively good agreement was reached between the two types of models, thus vindicating the usage of a complex rotational MBR model. Follow on studies will now compare results from the rotating MBR system using rotational models developed by other researchers to ascertain the effectiveness rotating MBR modelling approach.

In recent times, the soft robotics field is gaining numerous research focus owing to its high level of manipulation capabilities unlike traditional rigid robots, which gives room for an increasing use in other areas. However, compared to traditional rigid gripper robots, being capable of controlling/obtaining overall body stiffness when required is yet to be further explored since soft gripper robots have inherently less rigid properties. unlike previous designs with very complex variable stiffness systems, this paper demonstrates a soft gripper design with minimum system complexity while being capable of varying the stiffness of a continuum soft robotic actuator and proves to have potential applications in gripping objects of various shapes, weights & sizes. The soft gripper actuator comprises two separate mechanisms; the pneumatic mechanism for bending control and the mechanical structure for stiffness variation by pulling tendons using stepper motors which compresses the actuator, thereby changing the overall stiffness. The pneumatic mechanism was first fabricated and then embedded into another silicon layer during which it was as well merged with the mechanical structure for stiffness control. By first pneumatically actuating the actuator which causes bending and then pulling the tendons, we found out that the actuator stiffness value can be increased up to 145 % its initial value, and the gripper can grasp & lift a weight of up to 2.075 kg.

Three different approaches show that, contrary to a longstanding conviction older than 160 years, the advance of Mercury perihelion can be achieved in Newtonian gravity with a very high precision by correctly analysing the situation without neglecting Mercury’s mass. General relativity remains more precise than Newtonian physics, but Newtonian framework is more powerful than researchers and astronomers were thinking till now, at least for the case of Mercury. The Newtonian formula of the advance of planets' perihelion breaks down for the other planets. The predicted Newtonian result is indeed too strong for Venus and Earth. Therefore, it is also shown that corrections due to gravitational and rotational time dilation, in an intermediate framework which analyzes gravity between Newton and Einstein, solve the problem. By adding such corrections, a result consistent with the one of general relativity is indeed obtained. Thus, the most important results of this paper are two: i) It is not correct that Newtonian theory cannot predict the anomalous rate of precession of the perihelion of planets' orbit. The real problem is instead that a pure Newtonian prediction is too strong. ii) Perihelion's precession can be achieved with the same precision of general relativity by extending Newtonian gravity through the inclusion of gravitational and rotational time dilation effects. This second result is in agreement with a couple of recent and interesting papers of Hansen, Hartong and Obers. Differently from such papers, in the present work the importance of rotational time dilation is also highlighted.

AFM nanoindentation showed variation in stiffness (Elastic modulus) due to heterogenous nature of the collagen fibres. The S values varied from 5 N/m to 11.11 n/m corresponding to an E change of 2.25 to 1.38 GPa. The variation in effective modulus (Eff) with respect to displacement indicated crossing the parabolic limit. A softening index n was proposed due to the heterogenous behaviour of the biomaterials

Eicheon properties are discussed. It is shown that the eicheon surface allows setting a boundary condition for the vacuum polarization and obtaining a solution describing the dark matter tail in the Milky Way. That is, the dark matter in the Milky Way is explained as the F-type of vacuum polarization, which could be treated as dark radiation. The model presented is spherically symmetric, but a surface density of a baryonic galaxy disk is taken into account approximately by smearing the disk over a sphere. This allows the reproduction of the large distance shape of the Milky Way rotational curve. Andromeda's rotational curves are also discussed.

We consider rotational hypersurface in the four dimensional Euclidean space. We calculate the mean curvature and the Gaussian curvature, and some relations of the rotational hypersurface. Moreover, we define the third Laplace-Beltrami operator and apply it to the rotational hypersurface.

As a new type of gear, bevoloid gears have the advantages of compensating axial error, smooth transmission, and eliminating turning error, and they are widely used in applications requiring high transmission accuracy and stability. However, research on calculating the time-varying mesh stiffness of bevoloid gears is still limited, and there is an urgent need to propose a method that can calculate the stiffness of bevoloid gears quickly and accurately. This paper first establishes the bevoloid gear tooth profile expressions, then assumes a pair of bevoloid gears meshing with the same rack and derives the contact line equations of parallel axis bevoloid gear pairs, and analyze the contact process of bevoloid gears. We propose an analytical algorithm that uses the slicing method to calculate the stiffness of helical gears, straight bevoloid gears, and helical bevoloid gears, change the parameters of helical bevoloid gears respectively, and analyze the influence of different parameters on stiffness. Finally, the finite element method is used to verify the analytical method, and the correctness of the analytical calculation results is verified, and the errors are analyzed.

In the laboratory practice, several standards for testing the bending stiffness of corrugated board are used. There are often cases of tests where the results depend on the way the sample is placed on the supports. The problem arises when the board is five-ply (with two corrugated layers with different corrugation heights) or when the board has asymmetrically selected papers on the flat layers. In this article, we focus our attention on the problem related to boundary conditions, with particular attention to the local effects of the support of the sample. Since the cardboard layers, both flat and corrugated, have a small thickness, a slight deformation of the papers can always be observed at the point of contact between the sample and the support, which affects the readings of the measured stiffness. The paper presents theoretical and numerical analyzes showing how much the method of supporting the sample affects the measured bending stiffness of various samples. Numerical observations were also compared with the results of analyzes presented by other scientists as well as with experimental results.

As an emerging building solution, cross-laminated timber (CLT) floors have been increasingly used in mass timber construction. The current vibration design of CLT floors is conservative due to the assumption of simple support conditions in the floor-to-wall connections. It is noted that end fixity occurs as a result of clamping action at the ends, arising from the gravity load applied by the structure above the floor and by the mechanical fasteners. In this paper, the semi-rigid floor-to-wall connections are treated as elastically restrained edges against rotations to account for the effect of partial constraint. A rotational end-fixity factor was first defined to reflect the relative bending stiffness between CLT floors and elastic restraints at the edges. Then, for the design of vibration serviceability of CLT floors as per the Canadian Standard for Engineering Design in Wood (CSA O86), restraint coefficients were defined and their analytical expressions were derived for natural frequencies and the mid-span deflection under a concentrated load, respectively. In particular, a simplified formula of the restraint coefficient for the fundamental frequency was developed to assist engineers in practical design. At last, by comparing with reported experimental data, the proposed design formula showed excellent agreement with test results. In the end, the proposed end fixity factor with their corresponding restraint coefficients is recommended as an effective mechanics-based approach to account for the effect of end support conditions of CLT floors.

Introduction: Systemic lupus erythematosus (SLE) is an autoimmune disease associated with an increased risk of cardiovascular diseases (CVD), leading to elevated mortality rates among patients. We aimed to evaluate the levels of cardio-ankle vascular index (CAVI), global longitudinal strain (GLS), ventricular-arterial coupling (VAC) and high-sensitivity cardiac troponin (hsTn), in SLE patients and to explore their relationship with clinical parameters. Methods: This cross-sectional study enrolled 82 SLE patients without evident cardiac or kidney impairment and 41 age- and sex matched healthy controls. We comparatively evaluated CAVI, GLS, VAC, and hsTn between SLE patients and controls, and we assessed their association among SLE patients with disease activity based on the SELENA-SLEDAI Activity Index. Multivariate regression analysis was performed to identify independent predictors of CAVI and hsTn within the SLE cohort. Results: In comparison to healthy controls, SLE patients presented with significantly higher CAVI, GLS and hsTn levels, while VAC was significantly reduced (p<0.001). Further, SLE patients with active disease (SELENA-SLEDAI≥4) exhibited higher levels of CAVI and troponin than those with inactive disease (p<0.001). SLEDAI was an independent predictor of CAVI, while VAC and SLEDAI were independent determinants of hsTn in SLE cohort. Conclusion: SLE patients displayed abnormal levels of CAVI, VAC, GLS, and troponin compared to healthy individuals. Our findings implicate the potential of those CV novel CVD risk factors to refine screening and therapeutic strategies for this specific population.

It is necessary to address the scarcity of crushed stones for pavement structural layers. So fly ash can be proved to be promising solution as more than 270 tonnes of fly ash is generated in India. Though, numerous research has been conducted for the use of fly ash intreated and untreated form, high volume of fine particles and brittleness of the stabilized fly ash pose a great problem for its use in subbase and base. Moreover, stiffness or modulus of stabilized fly ash is vital elastic parameter which is used for mechanistic pavement design. Hence, in this study an extensive experimental investigation is carried out to study its strength and stiffness properties such as compressive strength, indirect tensile strength and flexural strength, cyclic indirect tensile modulus and flexural modulus of fiber reinforced cement stabilized fly ash, stone dust, aggregate mixtures. The stone dust and aggregates have been added to enhance the gradation of the composite’s mixture. The study presents the effect of fiber on strength and stiffness properties. The experimental result reveals that addition of polypropylene (PP) fibers up to 0.25 wt.% enhances the compressive strength and any further addition of fiber results in decrease of the strength. However, indirect tensile strength and flexural strength increases with increase in fiber percentage up to 0.5 wt.%. Cement content is observed to be the dominant parameter for stabilized materials. Suitable relationships have been developed between strength and modulus parameters for stabilized mixtures. Based on the strength and stiffness study, 70% fly ash and 30% stone dust-aggregate and 60% fly ash and 40% stone dust-aggregate with 6% cement can be considered for the base layer. Based on the indirect tensile strength and flexural strength behavior, 0.35% is considered as the optimum fiber percentage.

Small hydro-power systems seem to be the best solution for energy generation through the use of pump as turbine (PAT) due to its low cost and lesser environmental hazards associated with it. Recently, PAT applications are gaining global attention in energy generation but its operation is not fully understood. The performance and flow behavior is affected by several operational conditions. This study seeks to investigate the effects of rotational speed on flow behavior and performance of a PAT. Rotational speed is an important physical parameter that affects the operation of a PAT. A selected centrifugal pump model of four blades and splitters was used for the study. Numerical simulations were carried out using k-ε turbulence model to solve the three-dimensional (3D) equations in both pump and PAT modes. The outcomes were then validated using experimental results in the pump mode to obtain overview flow physiognomies. The results predicted that the efficiency increases as the rotational speed increases in the pump mode whereas in turbine mode, higher rotational speed cannot convert hydraulic energy into mechanical energy. Thus, a rotational speed of 1500 rpm performed the highest efficiency of 69.8% at QBEP among the other rotational speeds selected. Moreover, the head performance in the turbine mode increases as the flow rate increases. This research provides useful information which will help improve PAT performance as well as selecting PAT for small hydro-power site.

The steady streaming (SS) phenomenon is gaining increased attention in the microfluidics community, because it can generate net mass flow from the zero-mean vibration. We developed numerical simulation and experimental measurement tools to analyze this vibration induced flow, which has been challenging due to its unsteady nature. Validity of these analysis methods is confirmed by comparing the three-dimensional (3D) flow field induced around a cylindrical micropillar under circular vibration. In the numerical modeling, we directly solved the flow in the Lagrangian frame so that the substrate with a micropillar becomes stationary, and the result was converted to the Eulerian frame to compare them with the experimental results. The present approach enables to avoid the introduction of moving boundary or small perturbation approximation. The flow field obtained by the micro particle image velocimetry (PIV) measurement supported the three-dimensionality observed in the numerical results, which could be important for controlling the mass transport and manipulating particulate objects in the microfluidic systems.

Antioxidants reduce arterial stiffness but the effects previously reported are weak. The present study evaluated the effects of 2 weeks of therapy with a combination of antioxidants (l-cysteine, thiamine, pyridoxine and ascorbic acid) compared to placebo on stiffness index (SI) a measure of arterial stiffness that is strongly correlated with central pulse wave velocity (PWV), using a Pulse Trace recorder in a diverse group of 78 volunteers. SI fell by 1.7 m/sec relative to placebo (95% confidence intervals 0.6 to 2.7 m/sec), a reduction of 19% (95% confidence intervals 9% to 31%). The Glass effect size was 1.4, indicating a very strong treatment effect which was substantially greater than found in previous studies of the effects of antioxidant therapy on arterial stiffness. The magnitude of reduction in SI was positively correlated with increasing age (r = 0.362 P = 0.02). The change in RI, a measure of compliance of small to medium size arteries, did not differ between the antioxidant and placebo groups The combination of antioxidants studied reduced PWV to a much greater extent than reported for other antioxidants. This combination may be of value in the treatment of cardiovascular disease.

To improve the measurement accuracy of three-dimensional rotation angle of the spherical joint, a novel approach is proposed in this study, which combines the magnetic detection by Hall sensor and surface feature identification by eddy current sensor. Firstly, a permanent magnet is embedded in the ball head of spherical joint, and Hall sensors are set and distributed in the ball socket to measure the variation of magnetic flux density when spherical joint rotating, which are related to 3D rotation angle. In order to further improve measurement accuracy and robustness, we also set grooves on the ball head and use eddy current sensors to synchronously identify the rotation angle of the ball head. After the combination of two signals is adopted, a measurement model is established using the RBF neural network by training, and realized real-time measurement of the 3D rotation angle of spherical joint. The feasibility and superiority of this method are validated through experiments. The experimental results indicated that the measurement accuracy is promoted substantially compared to the preliminary measurement scheme based on spherical coding, the average measurement error of single axis is reduced by 9'9". The root mean square errors for the measurement of 3D rotation angles in this proposed method are as follows: the pitch angle α has an error of 1'8", the yaw angle β has an error of 2'15", and the roll angle γ has an error of 29'6".

This study assessed the relationship between body posture displacements and cardiopulmonary function test (CPET) and skill related physical fitness tests. One hundred male (60%) and female collegiate athletes (22.2 ± 4yrs) with a normal body mass index (BMI up to 24.9) were assessed via the PostureScreen Mobile app to quantify postural displacements as head, thorax and pelvis rotations and translations. CPET and physical performance tests including the agility T-test, the vertical jump test, the stork static balance test (SSBT) and the dynamic Y-balance test (YBT) were performed. Spearman correlation (r) and p-values are reported. Postural parameters were found to have moderate-to-high associations with CPET and the agility test, moderate correlations with the vertical jump test and the SSBT (head and pelvic postures only), and weak correlations with the YBT. As postural parameters were more asymmetric, both CPET and performance skills scores were worse. For examples: 1) a medium positive correlation was found between cranio-vertebral angle (CVA) and vertical jump test (r = 0.54; p-value < 0.001) and SSBT (r = 0.57; p-value < 0.001), while a strong negative correlation was found between CVA and agility test (r = -0.86; p-value < 0.001). 2) A strong positive correlation was found between CVA and oxygen uptake efficiency slope, load watts VO2 at VT, VO2 / kg, load watts at respiratory compensation point (RCP), (r = 0.65 and r = 0.71; p < 0.001). Conversely, a significant negative correlation was found between CVA and VE / VO2 at VT (r = -0.61; p < 0.001). Postural rotations and translations of the head, thorax and pelvis were statistically correlated with physical performance skills and CPET in young collegiate athletes. There were moderate-to-high associations with cardiopulmonary functions and agility tests, moderate correlations with the vertical jump test, and weak correlations with the YBT. Postural alignment may be important for optimal physical performance and optimal cardiopulmonary function. Further research is necessary to elucidate reasons for these correlations as found in our sample of young and healthy athletes.

Natural rocks are highly heterogeneous due to various geological processes that constantly alter their properties. The accumulation, deposition, and cementation of mineral and organic particles continuously modify the spatial characteristics of rock properties. Property variability or anisotropy is commonly observed in most rock types and influences strength, transport, and thermal conductivity behavior. This unpredictability presents a significant challenge for laboratory testing. Binder-jet additive manufacturing (3D printing) has emerged as a valuable technology for characterizing rock properties in geoscience and engineering. This study proposes a methodology to evaluate the variability and repeatability of mechanical properties of 3D-printed sandstones during binder-jet additive manufacturing. The mechanical properties were analyzed statistically for samples located in various parts of the 3D printer build volume. The results showed that the 3D-printed sandstones exhibited significant variations in their strength and stiffness properties when measured from samples produced within the same build volume during binder-jet additive manufacturing. The Uniaxial Compressive Strength (UCS) varied from 23 to 38 MPa, with an average value of 29 MPa. The Young's modulus, on the other hand, ranged from 1.5 to 4.05 GPa, with an average value of 2.33 GPa. The variability of the mechanical properties, quantified by the standard deviation, decreased when the entire population of 3D-printed sandstones was divided into smaller samples situated at different elevations of the build platform.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

The purpose of this study was to determine the effects of aerobic exercise on carotid to femoral pulse wave velocity (cf-PWV), cell adhesion molecules (intracellular adhesion molecules (ICAM-1), vascular cell adhesion molecules (VCAM-1), and endothelial selectin (E-selectin), and oxidized-LDL in elderly women aged 70–85 years, and to identify the effect of and correlation with vascular stiffness. Forty participants were recruited and divided into three groups; vascular stiffness (VSG, n=14), obesity (OG, n=14), and normal (NG, n=12). All groups were given a 16-week intervention of aerobic exercise, and the data collected before and after exercise were analyzed using SPSS Ver. 23.0. Two-way repeated-measures ANOVA was used to evaluate between-group and time-dependent interaction effects. One-way ANOVA was used to evaluate between-group variations. In addition, the significance was tested using a post-hoc test (Scheffe). The within-group variations by time before and after exercise were examined using a paired t-test, and correlation analysis was performed using Pearson correlation coefficients. Simple regression analysis was performed for variables showing significant differences. The results indicated interaction effects for cf-PWV (p<.001), VCAM-1 (p<.01), E-selectin (p<.05) and oxidized LDL (p<.001). The rate of change of cf-PWV was positively correlated with that of VCAM-1 (r=.352, p<.05) and that of oxidized-LDL (r=.325, p<.05) with statistical significance. To determine the effect of the rate of change of cf-PWV on the rate of change of VCAM-1, the variables were tested, and the coefficient of determination in the regression analysis was .124, indicating that 12.4% of the tested variables fit the standard regression line. The variables for the effect of the rate of change of cf-PWV on the rate of change of oxidized LDL were also tested, and the coefficient of determination in the regression analysis was .106, indicating that 10.6% of the tested variables fit the standard regression line. Thus, the 16-week regular and consistent aerobic exercise program had significant effects on the cf-PWV, ICAM-1, VCAM-1, E-selectin, and oxidized-LDL in elderly Korean women with vascular stiffness, suggesting improvements in vascular stiffness, based on which the intervention is predicted to contribute to the prevention of vascular dysfunction by lowering the risk of cardiovascular disease due to atherosclerosis, as well as having a positive effect in the prevention of impairment of vascular endothelial cells.

Variable Angle Tow (VAT) laminates offer a promising alternative to classical straight fiber composites in terms of design and performance. However, analyzing these structures can be more complex due to the introduction of new design variables. Carrera's Unified Formulation (CUF) has been successful in previous works for buckling, vibrational, and stress analysis of VAT plates. Typically, one-dimensional (1D) and two-dimensional (2D) CUF models are used, with a linear law describing the fiber orientation variation in the main plane of the structure. The objective of this article is to expand the CUF 2D plate finite elements family to perform free vibration analysis of composite laminated plate structures with curvilinear fibers. The primary contribution is the application of Reissner's Mixed Variational Theorem (RMVT) to a CUF finite element model. The Principle of Virtual Displacements (PVD) and RMVT are both used as variational statements for the study of monolayer and multilayer VAT plates dynamic behavior. The proposed approach is compared to Abaqus three-dimensional (3D) reference solutions, classical theories and literature results to investigate the effectiveness of the developed models. Results demonstrate that mixed theories provide the best approximation of the reference solution in all cases.

In this paper, we have shown the electronic circuit equivalence of a mechanical system consists of two oscillators coupled with each other. The mechanical design has the effects of the magnetic, resistance forces and the spring constant of the system is periodically varying. We have shown that the system’s state variables, such as the displacements and the velocities, under the effects of different forces, lead to some nonlinear behaviors, like a transition from the fixed point attractor to the chaotic attractor through the periodic and quasi-periodic attractors. We have constructed the equivalent electronic circuit of this mechanical system and have verified the numerically obtained behaviors using the electronic circuit.

Background: To rigorously derive easy to use formulae for the inclination angle for single cut rotation osteotomy that can be used for tibia deformity correction. Method: Three theorems were proven using trigonometric identities and concepts of linear algebra. These were rigorously shown. The three concepts were how to convert deformities in an AP/Lateral plane to an oblique plane deformity with a true angular magnitude of deformity; how to project an angular quantity from one plane to another; and the calculation of the inclination angle for the oblique osteotomy plane. All figures in this article were created by the authors of this paper. Results: From the formula derived, a statistical t-test was performed that showed no significant difference between the formula derived in this paper and the original Sangeorzan paper charts (p=0.0079). Conclusions: The formulae described in this article are a method to accurately calculate the inclination angle of the osteotomy for a single cut rotational osteotomy for tibial deformity correction. Clinical Relevance: The article gives a deeper understanding of fundamental concepts behind deformity correction and provides an easy-to-use mathematical formula to calculate the osteotomy inclination for single cut rotational osteotomies.

The alterations of coagulation status in patients with Severe Burn Injury are associated with serious complications, increased morbidity and mortality. This study aims to compare Rotational Thromboelastometry(ROTEM)–a Viscoelastic Coagulation Assays(VCAs) with Conventional Coagulation Assays(CCAs) including Prothrombin time(PT), Activated Partial Thromboplastin time(aPTT), International normalized ratio(INR), Complete Blood Count(CBC) and Coagulation Factors during the early five post- burn days in Survivors and Non- Survivors with Severe Burn Injury in order to correlate these results with Burn Coagulopathy and Prognosis. Seventeen Sur-vivors and ten Non- Survivors, with a mean Total Burn Surface Area(TBSA) of 33,78% were in-cluded in our study. Even though CCAs measurements were abnormal, they were unable to detect overall burn patients’ coagulopathy. On the contrary, VCAs from day 2 to day 5 took pathological values, especially for Non- survivors. Those changes were underlined through pathological values of Coagulation Factors. As a result, CCAs were considered poor indicators of coagulation status in burn injury, whereas VCAs were more accurate in demonstrating coagulation alterations from the early post- burn period and detecting patients in greater risk of mortality. These advantages of VCAs could be used for timely intervention in high risk patients and for the guidance of blood product transfusions.

Background: Myocardial infarction is increasing at a young age. New tools are needed to evaluate the risk population of young patients. GDF-15 has been implicated in several key mechanisms of atherogenesis and also is associated with increased mortality and cardiovascular events in patients with coronary artery disease. Arterial stiffness parameters, including pulse wave velocity, can also be measured using peripheral arterial tonometry and can indicate the presence or progression of atherosclerotic changes. The aim of this study is to evaluate the GDF-15 level and arterial stiffness parameters in patients with premature myocardial infarction Method: Thirty patients who recovered from a myocardial infarction were consecutively included. Fifteen age-sex-matched subjects were included as controls. The patients’ serum GDF-15 concentration levels were measured using relevant kits. Measurements of arterial stiffness [pulse-wave velocity (PWV) and augmentation index (AIx)] were performed using a Mobil-O-Graph arteriography system. Results: GDF-15 concentration levels were significantly higher in the patients with premature myocardial infarction when compared to controls. PWV and AIx were similar between the groups. GDF-15 level was negatively correlated with high-density cholesterol (HDL) and positively correlated with uric acid levels in all study populations. Conclusions: GDF-15 levels may be a risk factor for patients with premature myocardial infarction. This pilot study may trigger further studies to elucidate the central role of GDF-15 in the pathophysiology of early atherosclerosis in the young population.

The subject of the research is the investigation of the behavior of railway tracks in locations with a significant change in the stiffness of the track. These locations can be designed from various structural elements and their materials, and this mainly results in a height change of the track level during its operation. These transition zones are monitored and expertly examined in order to detect undesirable deformations of the geometrical position of the track caused by the trains running. The transition zones are at the points where the fixed track transitions to the classic track bed, in our case it is their combination with bridge structures, especially at their supports. In Slovakia, under the conditions of the Railways of the Slovak Republic, the issue is topical within the framework of the modernization of trans-European railway corridors. The results of experimental measurements and their analysis will provide relevant data for subsequent research solutions for their new numerical modeling, which will ensure a smooth passage through these points of change without height fluctuations, vibrations, and shocks from the wheels of train sets.

This study presents a platform for ex-vivo detection of cancer nodules, addressing automation of medical diagnoses in surgery and associated histological analyses. The proposed approach takes advantage of the property of cancer to alter the mechanical and acoustical properties of tissues, because of changes in stiffness and density. A force sensor and an ultrasound probe were combined to detect such alterations during force-regulated indentations. To explore the specimens, regardless of their orientation and shape, a scanned area of the test sample was defined using shape recognition applying optical background subtraction to the images captured by a camera. The motorized platform was validated using seven phantom tissues, simulating the mechanical and acoustical properties of ex-vivo diseased tissues, including stiffer nodules that can be encountered in pathological conditions during histological analyses. Results demonstrated the platform’s ability to automatically explore and identify the inclusions in the phantom. Overall, the system was able to correctly identify up to 90.3% of the inclusions by means of stiffness in combination with ultrasound measurements, paving pathway towards robotic palpation during intraoperative examinations.

The natural distribution of stress in the femur is altered when total hip arthroplasty (THA) is performed. In fact, when a stem is inserted inside the femur, there is a variation in stress due to the difference in rigidity between the material with which the stem is made and the femur. This generates the phenomenon of stress-shielding. The aim of this study is to design an optimized prosthesis that guarantees excellent rotational stability and re-duced stress shielding. Methods: through the finite element method (FEM) the mechanical behavior of the stem subjected to the loads described by ISO 7206-4: 2010 is studied. Re-sults: Through topological optimization, there is a reduction in stress shielding in the proximal zone of 31.46%. The addition of ridges on the dorsal side of the stem also im-proves rotational stability by 27.82%. Conclusions: The decrease in stiffness that is rec-orded with the optimized stem, guarantees a greater distribution of stress on the bone. The presence of dorsal ridges also favors the corticalization of the bone as it loads the bone near the dorsal ensuring further stability. The perforated prosthesis presented in this study, shows an increase in primary stability and an improvement in rotational stability. As there is also a bone regrowth inside the prosthesis.

In this study, we describe quark confinement in terms of linear interaction potentials and solve the problem of the net spin of a proton. The three quarks in a proton are assumed to revolve around a common center, and their masses are determined assuming they are Dirac particles. On the basis of these assumptions, the magnetic moment of a proton can be derived. Moreover, the rotation of the quarks is considered, in which an electrical current induces a magnetic field. Thus, the scalar product of the magnetic moment and field describes the linear interaction potential between the quarks, and the mass of the proton can be obtained. The proton mass predicted by this physical model is consistent with experimental values, and no numerical or fitting calculations are required. Furthermore, using the newly derived spins and angular momentum of the three quarks, we derived the net spin of a proton. Additionally, we predicted the mass of a pi-meson from the same model, which agrees with the experimental values.

Aiming at the problem that soft robots are challenging to take into account both flexibility and bearing capacity, Using the software Pneu-Net driver as the deformation mode, magnetorheological fluid material phase transformation to achieve variable stiffness, A pneumatic modular soft joint structure with dynamically adjustable deformation and stiffness in all directions is proposed. In this paper, mathematical models of deformation and variable stiffness are established. The correspondence between gas pressure and deformation and applied current and joint stiffness is obtained. The finite element analysis method was used to simulate the deformation characteristics and variable stiffness characteristics of modular joints based on the Yeoh model. Finally, the theoretical and simulation results are verified by deformation and variable stiffness tests. It is proved that the modular joint has good rigid-flexible coupling characteristics.

In this paper, the effect of multi-rotational speeds super-gravity field on the grain refinement and tensile properties of as-cast H13 steel were investigated systematically. The experimental results revealed that the as-cast grains of H13 steel can be significantly refined in multi-rotational speeds supergravity field. In conventional supergravity field, with the decrease of rotational radius, the secondary dendrite average spacing (SDAS) and the austenite grain average size (AGAS) increase, and the maximum values of SDAS and AGAS are 90 µm and 55 µm, respectively. while in multi-speeds supergravity fields, at the range of increasing rotational speeds, SDAS and AGAS decrease as the rotational radius decreases. In three-rotational speeds supergravity field, the maximum values of SDAS and AGAS are 80 µm and 50 µm. In five-rotational speeds supergravity field, the maximum values of SDAS and AGAS are reduced to 58 µm and 34 µm. Accordingly, both the tensile strength and the plasticity are enhanced with the increasing the number of rotational speeds in supergravity field, especially for the inner position of supergravity sample. The ultimate tensile strengths at outer, middle, and inner positions of H13 steel solidified in conventional supergravity field are 1445 MPa, 1378 MPa, and 1023 MPa, corresponding elongations of 2%, 1.5%, and 0.5%, while in the five-rotational speeds supergravity field, they are 1408 MPa, 1443 MPa, and 1453 MPa, corresponding elongations of 1.8%, 3.9%, and 2.2%. The mechanism for the grain refinement is that multi-speeds super-gravity can reduce the critical nucleation work of austenite, and the tangential force produced by changing the rotational speeds breaks dendrites at the solidification front, refining solidification structure.

This paper mainly analyzes the design and control of the rotational inverted pendulum, and presents a state space expression. Since the system is highly unstable a feedback control system is used. Augmentations with weighting functions based mixed sensetivity and H2 optimal control methods are used to make the system stable for uprise position. The rotational inverted pendulum have been simulated and compared with the proposed controllers and a promising results have been analyzed sussesfuly.

Offshore Wind Turbines (OWT) with increasingly higher energy output are being developed to meet energy demand, posing challenges for their foundation design. Several foundation types are used to support these turbines with monopiles (MP) accounting for 80% of the installed capacity. In this study, three-dimensional (3D) nonlinear finite element models (FEM) were employed to investigate the behaviour of monopile foundation supporting a 5MW wind turbine when subjected to lateral loading. Results indicate that the MP behavior depending on the pile length to diameter (L/D) ratio and the soil shear strength. Inspection of bending moment profiles at the lateral ultimate capacity indicated the monopiles can behave in flexible manner even with low L/D ratio. The L/D ratio affected the MP normalized lateral ultimate capacity at varying degrees and the biggest effect was for soft clays, amounting to around 5 folds increase for L/D values of 3.33 to 13.33. Lesser effects were found for stiff clays.

In this paper, a kind of single-walled carbon nanotube nonlinear model is developed, and the strongly nonlinear dynamic characteristics of such carbon nanotubes subjected to random magnetic field are studied. The nonlocal effect of microstructure is considered based on the theory of nonlocal elasticity. The natural frequency of the strongly nonlinear dynamic system is obtained by the energy function method, the drift coefficient and the diffusion coefficient are verified. The stationary probability density function of the system dynamic response is given and the fractal boundary of the safe basin is provided. Theoretical analysis and numerical simulation show that stochastic resonance occurs when varying the random magnetic field intensity. The boundary of safe basin has fractal characteristics and the area of safe basin decreases when the intensity of the magnetic field permeability increases.

Soil erosion is one of the biggest problems in the agricultural sector that can affect ecosystems and human societies. A field of 50 slope was selected to study the runoff, soil and nutrients’ loss as well as crop productivity in different treatments (conventional tillage (CT) vs. no-tillage (NT), plant vs. no plant cover, contour cultivation (CC) vs. perpendicular to the contour cultivation, (PC) under natural rainfall. The experiment was conducted in central Greece in two cultivation periods. In autumn, the field was cultivated with intercropping Triticosecale and Pisum sativum and in spring with Sunflower. The total rainfall was 141.4 mm in the 1st year and 311 mm in the 2nd. We found that runoff in the treatment of no tillage with contour cultivation was 85% lower in both years compared to the no tillage-no plant control. Therefore, the contour cultivation-no tillage treatment had a positively effect in decreasing phosphorus and potassium concentrations lost from soil: indeed, there was a decrease by 55% and 62% in P and K, respectively, in the NT compared to the CC treatments. We conclude that the NT-CC treatment with plant cover was the most effective in reducing water runoff, soil nutrients’ loss and increasing yield.

Hypertension and arterial stiffness are the main factors contributing to cardiovascular disease. L-citrulline, a nitric oxide precursor, has been proposed as a blood pressure-lowering intervention. This study aimed to investigate the impact of L-citrulline on central and peripheral blood pressure, arterial stiffness, and muscle oxygenation at rest and during an isometric knee extension exercise protocol. Twelve older males received 6 g of L-citrulline or a placebo for six days using a double-blind crossover design. Blood hemodynamics parameters (i.e., arterial and brachial systolic and diastolic blood pressure, mean arterial pressure, pulse pressure, heart rate), arterial stiffness (i.e., augmented pressure, augmentation index, forward, backward wave pressure and carotid-femoral pulse wave velocity) and muscle oxygenation [i.e., oxyhemoglobin (Δ[O2Hb]) and deoxyhemoglobin (Δ[HHb]), total hemoglobin concentration (Δ[tHb]) and tissue saturation index (TSI%)], were measured at baseline, post-supplementation and during isometric exercise. No significant effects of L-citrulline supplementation were observed at rest or during exercise on blood pressure, arterial stiffness, and muscle blood flow. Both central and peripheral blood pressure were increased during the exercise, which is consistent with isometric contractions. The results of the present study question the efficacy of short-term L-citrulline in decreasing blood pressure at rest or attenuating blood pressure increases during isometric exercise.

In critically ill patients with COVID-19, concomitant abnormalities of coagulation have been seen with an unusually high incidence. Standard coagulation tests are limited in their ability accurately to reflect the severity of the pro-thrombotic phenotype observed in severe COVID-19 infections. In this narrative review we consider the role of rotational thromboelastometry (ROTEM) as a near bedside test allowing a more comprehensive assessment of haemostatic function in the context of COVID-19 infection. Comprehensive literature search was conducted on PubMed, revealing 13 publications on the subject. The coagulopathy of this disease process appears to be insufficiently represented with often normal conventional coagulation test parameters. Whilst not the perfect substitute for in vivo coagulation, studies utilising rotational thromboelastometry assays in COVID-19 patients have demonstrated increased maximum clot firmness (consistent with hyper-coagulability) and reduced maximum lysis (consistent with “fibrinolytic shutdown”). ROTEM appears to be a possible tool for risk stratification and to monitor the potential modulation of fibrinogen-dependent coagulation processes with enhanced anti-coagulation strategies. Precisely how these coagulation abnormalities can be modified by optimum, individualised medical interventions to improve clinical outcome, however, remains unclear.

Mechanical properties of tumor cytoskeleton are extremely vital for any phases of cancer, especially in tumor invasion and metastasis. However, in current category of anticancer drugs, the cytoskeleton-targeting drugs are limited and its role in tumor progression is unclear. Here, we present the mechanical characteristics of tumor stiffness are tightly regulated by cancer cytoskeleton including actin filaments and microtubule during tumor initiation, growth and metastasis, and review the natural drugs that target cancer cytoskeleton. We define cytoskeleton dynamics as target mechanisms for anticancer drug, and summary the plant, microbial and marine sources of natural products. Furthermore, the material approaches to active cancer mechanics are supplied in this review. We aim to promote the development of anticancer drugs that target tumor mechanics by using those material approaches in future and find its pharmacological application.

Ambient vibration energy is widely being harnessed as a source of electrical energy to drive low-power devices. The vibration energy harvester (VEH) of interest employs an electromagnetic transduction mechanism, whereby ambient mechanical vibration is converted to electrical energy. The limitations affecting the performance of VEHs, with an electromagnetic transduction structure, include its operational bandwidth as well as the enclosure-size constraint. In this study, an analysis and design of a nonlinear VEH system is conducted, using the Output Frequency Response Function (OFRF) representations of the actual system model. However, the OFRF representations are determined from the Generalised Associated Linear Equation (GALE) decompositions of the system of interest. The effect of both nonlinear damping and stiffness characteristics, to respectively extend the average power and operational bandwidth of the VEH device, is demonstrated.

Background: This study aimed to contribute to the standardization of elastography by comparing stiffness values obtained from ultrasound elastography (US-E) and magnetic resonance elastography (MR-E) of the testicular parenchyma in healthy subjects. Methods: A total of 22 healthy volunteers (44 testes) were included in this study. Of the 26 cases analyzed, four were excluded from the study due to the exclusion criteria. The testicular parenchyma of the included patients was evaluated using MR-E and Shear-Wave Ultrasound Elastography (SW-E) examinations. Pearson's correlation test was used to calculate the correlation between age and stiffness values, testicular volumes and stiffness values, and stiffness values from both examinations. Results: The mean US-E stiffness of the right testes was 5.560 ± 3.1 kPa and the mean US-E stiffness of the left testes was 5.361 ± 2.9 kPa. The mean MR-E stiffness of the right testes was 6960.11 ± 460 Pa and the mean MR-E stiffness of the left testes was 6560.19 ± 310 Pa. There was no significant correlation between US-E and MR-E stiffness values (p=0.096). There was also no significant statistical correlation between US-E and MR-E stiffness values and testicular volumes (p=0.17 and p=0.093). Conclusions: No statistical correlation was found between the stiffness values obtained by SW-E and those obtained by MR-E in the normal testicular parenchyma. Additionally, no conclusive relationship between stiffness levels, age, or testicular volume was discovered.

Cells actively sense differences in topology, matrix elasticity and protein composition of the extracellular microenvironment and adapt their function and morphology. In this study, we focus on the cross-talk between matrix stiffness and protein coating density that regulate morphology and proliferation dynamics of single myocytes. For this, C2C12 myocytes were monitored on L-DOPA functionalized hydrogels of 22 different elasticity and fibronectin density compositions. Static images were recorded and statistically analyzed to determine morphological differences and to identify the optimized extracellular matrix (ECM). Using that information, selected ECMs were used to study the dynamics before and after cell proliferation by statistical comparison of distinct cell states. We observed a fibronectin density independent increase of the projected cell area until 12 kPa. Additionally, changes in the fibronectin density led to an area optimum at about 2.6 μg/cm, which was confirmed by an independent F-actin analysis, revealing a maximum actin filament to cell area ratio of 7.5 %. The proliferation evaluation showed an opposite correlation between cell spreading duration and speed to the matrix elasticity and protein density, which did not affect the cell cycle duration. In summary, we identified an optimized ECM composition, while independent matrix properties regulate distinct cell characteristics.

In this study, Fe-based superconductors (SCs) are described with a model showing a novel attractive force. First, we describe this novel force using an analog from electromagnetism. From electromagnetism, it was found that this force is a Lorentz force in which two electrons orbit around a Fe-ion with the same velocity. Then, we consider a wave function of an electron. Consequently, due to the property of the proposed attractive force and the quantum-field Hamiltonian, we clarified that the Bardeen–Cooper–Schrieffer (BCS) ground state can be reused. Afterward, attractive force energy was calculated according to the presented model. In Fe-based SCs, a structure transition is essential. Considering that the derived attractive force energy is relatively large, we employ the expanded T_c-equation from the BCS theory that includes the structure transition effect and the derived attractive force energy. In addition, we succeed in analytically reproducing T_c-dome diagrams in various types of Fe-based SCs. Moreover, we discuss the universal property a general SC should have as well as the quantum critical point.

Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

Arthroscopic capsular release (ACR) is used for persistent shoulder stiffness after an index surgery. No cases of post-ACR humeral head osteonecrosis have been reported to date. A 56-year-old male patient underwent open reduction and internal fixation using a hook plate for acromioclavicular joint dislocation. Despite hardware removal, the patient presented with unresolved shoulder pain and range-of-motion (ROM) limitation. He had a history of hypertension, chronic hepatitis B infection, and alcohol consumption. Preoperative ROM was forward flexion 90°and internal rotation sacral level. Preoperative functional status was visual analog scale (VAS) score 4, American Shoulder and Elbow Surgeons (ASES) score 51, and Constant–Murley (CMS) score 48, and normal radiography and magnetic resonance imaging. Standard ACR was performed with 360° release of the joint capsule via electrocautery ablation. Six-months post-ACR, ROM (forward flexion: 135°, abduction: 135°, external rotation: 70°, internal rotation: T10 vertebra) and functional outcomes (VAS 2; ASES79; CMS 75) were significantly improved, without interval change in radiographic assessment. However, 21 months later, he had recurrent shoulder pain and decreased ROM. Radiography revealed humeral head osteonecrosis. Patients with intrinsic or extrinsic risk factors related to humeral head circulation disturbance should be monitored for humeral head osteonecrosis post-ACR.

Background: We aimed to determine the splenic stiffness (SS) values in healthy individuals as measured by 3 Tesla magnetic resonance elastography (3T MRE) and to investigate the possible effects of parameters such as age, sex, spleen volume, diameter, and parenchyma thickness on SS.Methods: A total of 54 healthy volunteers were included in this cross-sectional study. Participants' age and sex information were recorded, in addition to spleen craniocaudal and anteroposterior diameter, cortical thickness, spleen volume, and SS, which were measured using 3T magnetic resonance imaging and MRE. Results: Twenty-nine male and 25 female subjects with a mean age of 54.78±15.40 years were included in the study. Mean cradiocaudal diameter was 10.46±1.16 cm, anteroposterior diameter was 9.88±1.29 cm, parenchyma thickness was 4.08±0.67 cm, SS was 3721.94±709.69 Pascal (Pa), and median spleen volume was 292.54 (239.40-311.00) cm³. A significant positive correlation was observed between age and SS (r=0.779, p<0.001). The SS values were not associated with sex, craniocaudal diameter, anteroposterior diameter, parenchymal thickness, or volume.Conclusion:Age should be considered when using SS in the diagnosis and staging of relevant diseases such as portal hypertension and esophageal varices. Our results should be confirmed by future studies using 3T MRE in larger populations.

Background: We aimed to determine the splenic stiffness (SS) values in healthy individuals as measured by 3 Tesla magnetic resonance elastography (3T MRE) and to investigate the possible effects of parameters such as age, sex, spleen volume, diameter, and parenchyma thickness on SS. Methods: A total of 54 healthy volunteers were included in this cross-sectional study. Participants' age and sex information were recorded, in addition to spleen craniocaudal and anteroposterior diameter, cortical thickness, spleen volume, and SS, which were measured using 3T magnetic resonance imaging and MRE. Results: Twenty-nine male and 25 female subjects with a mean age of 54.78±15.40 years were included in the study. Mean cradiocaudal diameter was 10.46±1.16 cm, anteroposterior diameter was 9.88±1.29 cm, parenchyma thickness was 4.08±0.67 cm, SS was 3721.94±709.69 Pascal (Pa), and median spleen volume was 292.54 (239.40-311.00) cm3. A significant positive correlation was observed between age and SS (r=0.779, p<0.001). The SS values were not associated with sex, craniocaudal diameter, anteroposterior diameter, parenchymal thickness, or volume Conclusion:Age should be considered when using SS in the diagnosis and staging of relevant diseases such as portal hypertension and esophageal varices. Our results should be confirmed by future studies using 3T MRE in larger populations.

In this paper, the effect of multi-pass friction stir processing on the mechanical properties of AZ91 alloy has been studied. For the numerical investigation, this process has been simulated with the three-dimensional numerical modeling based on the ABAQUS/Explicit. This simulation involves the Johnson-Cook models for defining the material behavior during this intense plastic deformation and investigating the fracture criterion. The tool plunging and stirring phases in the two-pass process has been simulated. To prevent too much distortion of elements during modeling, the Arbitrary Lagrangian-Eulerian technique for automatically re-meshing of distorted elements has been used. The model was calibrated using the experimental results from the previous works. This model can predict the transient temperature distribution and residual stress field during FSP on AZ91. The results show that the maximum temperature in the advancing-side region is more than that in the retreating-side region. In addition, numerical results show that at the end position of the process, the tool during the lift-up leaves the keyhole region in the compressive stress state. The experimental results investigated the effect of multi-pass FSP on the microstructure, microhardness, tensile and creep properties of AZ91 magnesium alloy. The FSP is performed by applying 50% overlapping. The tensile, and creep tests are conducted at several temperatures from 25 to 210 °C. The optical microscopy and scanning electron micrograph (SEM) were used to study the microstructure of the samples after performing multi-pass friction stir processing. The experimental results indicate that on average, the tensile strength, microhardness, and creep strength of the processed samples increased by about 29, 23, and 38 %, respectively compared to the unprocessed ones.

In this paper, a modular wire-actuated robotic arm was designed to improve the safety and adaptability of service robots during human-robot interaction. To raise the stiffness adjustment range of the robotic arm, a symmetric variable-stiffness unit was designed based on flexure, which had compact and simple structure, and lowly nonlinear stiffness-force relationship. In this paper, we focused on the research of the symmetric 1-DOF joint module. Based on the kinematics and stiffness analysis, the pose of the joint module could be adjusted by controlling the length of the wires, and the stiffness of the joint module could be adjusted by controlling the tension of the wires. Because of the actuation redundancy, the pose and stiffness of the joint module could be controlled synchronously. Furthermore, a directly method was proposed for the stiffness-oriented wire tension distribution problem of the 1-DOF joint module. A simulation was carried out to verify the proposed method.

Chronic hemodialysis (HD) patients have very high cardiovascular risk. Acute vascular changes during dialysis mediated by factors of the endothelium may have a crucial role in this. Aim: To study acute vascular changes during HD. In 29 consecutive chronic HD patients (age: 65.6±10.4 years) pre-, mid-, and post-HD plasma syndecan-1 (SDC-1) and endothelin-1 (ET-1) levels were measured. Applanation tonometry was performed before HD. SDC-1 levels increased during HD (p=0.004). Males had higher ET-1 levels. Patients were divided into 2 groups based on pulse wave velocity (PWV): PWV≥12 m/s and PWV<12 m/s. Pre-HD and mid-HD SDC-1 levels were higher in the group with PWV≥12 m/s (10.174±2.568 vs. 7.928±1.794 ng/ml, p=0.013, and 10.319±3.482 vs. 8.248±1.793 ng/ml, p=0.044, respectively). Post-HD ET-1 levels were higher in the patient group having PWV≥12 m/s (10.88±3.00 vs. 8.05±3.48 pg/l, p=0.027). Patients having PWV≥12 m/s had higher pre-HD peripheral and aortic systolic blood pressure (p<0.05). Total cholesterol correlated with the SDC-1 decrease during HD (r=0.539; p=0.008). Pre-, mid-, and post-HD SDC-1 correlated with the ultrafiltration (r=0.432, p=0.019; r=0.377, p=0.044; and r=0.401, p=0.012, respectively). SDC-1 and ET-1 contribute to vascular changes observed during HD, and they have correlations with some cardiovascular risk factors.

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals like magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For WE43 scaffolds, during the first days an increase of the smeared Young's modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the struts surfaces. In this study the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite element simulations are performed to study the influence of the substrate layer thickness and Young's modulus for single struts and for a new scaffold geometry with adapted polar f2cc,z unit cells. The finite element model is further validated by compression tests on AM scaffolds made from Zn1Mg. The results show, that even low thicknesses and Young's moduli of the substrate layer increases significantly the smeared Young's modulus under axial compression.

(1) Background: Globally, neck pain is prevalent, affecting around thirty percent of the population annually. To better understand the influence of pain on the myofascial layers, the present study investigated these on the upper trapezius muscle in unilateral, more severe neck pain. (2) Methods: This study was a cross-sectional study. Forty patients (42.2 ± 14.7) with a confirmed diagnosis of unilateral neck pain were examined using durometry and indentometry. The study evaluated stiffness, elasticity, and pressure pain threshold of both sides of the neck (symptomatic side: SS; healthy side: HS). Furthermore, the range of motion of the cervical spine (lateral flexion, rotation) was quantified using a digital goniometer. (3) Results: A significant lateral discrepancy was observed in stiffness between groups (durometry: SS – 33.76 ± 7.78, HS – 29.75 ± 7.45, p&lt;0.001; indentometry: SS – 59.73 ± 33.93, HS – 4.18 ± 12.69, p=0.024). In contrast, no differences were found between the comparison sides of the upper trapezius for the parameter’s elasticity (SS – 0.101 ± 1.09, HS – -0.006 ± 0.29, p=0.416), cervical spine mobility (lateral flexion: SS – 37.08 ± 8.15, HS – 37.73 ± 7.61, p=0.559; rotation: SS – 73.55 ± 12.37, HS – 72.85 ± 11.10, p=0.660) and algometry (SS – 36.41 ± 17.53, HS – 37.22 ± 17.00, p=0.657). (4) Conclusion: Overall, it can be concluded that more severe neck pain unilaterally shows differences in stiffness on the same side. Future research is needed to investigate the links.

Background: Heart failure with preserved ejection fraction (HFpEF) is a major health concern. There is a growing recognition of the causal interplay between arterial stiffness and HFpEF. We recently reported that phosphate retention is a trigger for arterial stiffness. This study focuses on whether arterial stiffness due to phosphate retention could be a predictor for HFpEF. Methods: The study subjects were 158 patients (68 males and 90 females, mean age 74.8±11.2). HFpEF was defined according to the guidelines of the ESC 2019. Pulse wave velocity (PWV) and central systolic blood pressure (CSBP) were used as markers for arterial stiffness and afterload, respectively. We measured serum levels of fibroblast growth factor 23 (FGF23) as a marker of phosphate retention. Results: The serum levels of FGF23 had significant relationship with PWV. PWV had significant relationships with LV mass index, plasma BNP levels, and relative wall thickness, e’ and E/e’ (p<0.001, respectively). Multivariate logistic regression analysis revealed that PWV higher values and hypertension were significant predictors for the dependent factor (HFpEF). Conclusions: Arterial stiffness amplified LV afterload, leading to LV concentric hypertrophy and LV diastolic dysfunction. This study presents that arterial stiffness due to phosphate retention, and hypertension are important predictors of HFpEF.

In order to alleviate the problems regarding conventional damping modeling techniques in nonlinear structural simulations, using concentrated plasticity formulation including rotational end springs with no damping plus middle elastic parts with modified assigned damping has recently been proposed. However, a proper selection for springs’ stiffness is a source of contention. In this paper, the effect of choosing different ratios for springs’ rotational stiffness to the elastic part of the elements on the seismic performance of RC moment frames was investigated. Incremental Dynamic Analysis (IDA) was performed and the derived responses were used for seismic performance assessment methodology. The results demonstrate that using flexible springs may lead to a greatly conservative estimation of collapse capacity, annual losses, and repair costs compared to a rigid one. Due to lack of experimental data, it is not possible to certainly assert the most appropriate ratio. However, such variation in the seismic performance of a building model with different stiffness modification necessitates more investigation on this modeling strategy.

In this paper we give the improved and new analytical and semi-analytical expression for calcu-lating the magnetic vector potential, magnetic field, magnetic force, mutual inductance, torque, and stiffness between two inclined current-carrying arc segments in air. The expressions are ob-tained either in the analytical form over the incomplete elliptic integrals of the first and the sec-ond time or by the single numerical integration of some elliptical integrals of the first and the second kind. The validity of the presented formulas is proved from the special cases when the inclined circular loops are treated. We mention that all formulas are obtain by the integral ap-proach except the stiffness which is found by the derivative of the magnetic force.

The mass of a direct-drive generator is often defined by the requirements for structural stiffness to meet the magnetic stiffness between the rotor and stator surfaces. This paper analyses this magnetic stiffness and estimates the structural stiffness of direct-drive generators for different modes of deflection. The magnetic stiffness modelling is based on an analytical model of the airgap closing forces. The final models are verified using Finite Element analysis and carried out for both permanent magnet and wound rotor generators. It shows that wound rotor machines have higher stiffness requirements than permanent magnet machines. The structural stiffness of the generator rotor and stator are evaluated for different modes by applying spatially-varying forces and finding the associated deflections. Structural stiffnesses for the rotor, stator and bearing are then combined. Finally, the magnetic and structural stiffnesses are combined and a stiffness margin can be found. For the airgap not to close, this combined stiffness must be greater than 0. This method is applied to a relatively stiff and a relatively compliant set of generator structures in a case study in order to find the optimum and more sustainable configuration.

This paper analyses the viability of different solutions to passively augment the axial stiffness of a horizontal axis radial levitation passive magnetic bearing (PMB) with topology previously studied. The zero-field cooling (ZFC) of high-temperature superconductor (HTS) bulks promotes higher magnetic impulsion and levitation forces and lower electromagnetic losses than with the field-cooling (FC), but on the other hand, the guiding stability is much lower than with FC. Because of stability reasons, FC was adopted in most superconducting maglev systems. The trend of this research group has been to develop an HTS ZFC horizontal axis radial levitation PMB presenting notable levitation forces with reduced electromagnetic losses, defined by a topology that creates guiding stability. Previous work has shown that even optimizing the bearing geometry to maximize magnetic guidance forces, could not be enough to guarantee the axial stiffness required for many applications. First, the extent to which guidance forces are augmented by increasing the number of HTS bulks in the stator is evaluated. Then, the axial stiffness augmentation by passively adding two limiting permanent magnet (PM) rings is evaluated. Results show that the axial stiffness is highly augmented by adding limiting PM rings with no significant additional investment. This change enables using the studied ZFC superconducting PMB in high-precision axial stability applications, such as precision gyroscopes, horizontal axis propellers and turbines.

The influence of instrumental variables on farmers ‘perceptions using rotation fallow as sustainable agriculture practices had been the aim of our research. By using simultaneous equations models, this study tried to understand the relationship between green manure farmer’s perceptions on using rotation-fallow and planting green manure in Guangxi Province, south of China. The results showed that subsidizing green manure farmers based on standard subsidy by the unit of green manure sown area; the training on the green manure planting technology or the demonstration preaching; the green manure farmers preference for the kinds of subsidy (funds, seeds, and mechanical services) were the mostly great drivers of the program of restoring planting green manure in the study area. These incentives measures must be enhanced as priority to restore definitely green manure planting. However, the findings of the study showed that the total income of the 2017 year, the area of an agricultural field of household and the household members (16–65 years old), providing labor in the agricultural field, have some influences on planting green manure and on farmer’s perceptions on using rotation-fallow as sustainable agriculture practices. Brief, the unobserved factors which influenced the endogenous factors play an important role to enhance widely the impact of farmers’ perceptions on planting green manure.

The relationship between arterial stiffness and oxygen uptake (VO2) in patients with acute myocardial infarction (AMI) remains unclear. We aimed to investigate this relationship and factors contributing to VO2 in patients with AMI. The role of arterial stiffness in cardiac-skeletal muscle coupling during exercise was then elucidated. The exercise capacity via cardiopulmonary exercise testing (CPX), cardio-ankle vascular index (CAVI), and body composition of 101 patients with AMI were measured at discharge. Patients were categorized based on their CAVI into three groups: (i) normal (CAVI: ≤7.9), (ii) borderline (CAVI: 8.0–8.9), and (iii) abnormal (CAVI: ≥9.0). Subsequently, VO2 was compared among these groups. The relationship between the CAVI and peak VO2 (VO2 Peak) during CPX and factors contributing to VO2 Peak were investigated. The abnormal CAVI group had a significantly lower VO2 Peak than the normal and borderline groups. The CAVI was associated with VO2 Peak in patients with AMI. Furthermore, the CAVI was found to be a factor contributing to VO2 Peak. These findings suggest that arterial stiffness in tissue blood distribution and blood supply defines systemic exercise limits in patients with AMI. This suggested that arterial stiffness plays a significant role in cardio-vascular-skeletal muscle coupling.

The aim of the study was to examine the long-term prognostic value of changes in cardio-ankle vascular index (CAVI) within a year after coronary artery bypass grafting (CABG). Methods. Patients with coronary artery disease (n = 251) in whom cardio-ankle vascular index (CAVI) was assessed using the VaSera VS-1000 device before and in a year after CABG. Groups with improved CAVI (CAVI decreased from pathological value to normal or the index remained within normal values) or worsened CAVI (persistent pathological index value or an increase in CAVI to pathological values or an increase of 1 unit or more) were identified. The groups were compared for the following events at 10-year follow-up: death from all causes, myocardial infarction, stroke/transient ischemic attack, and the combined endpoint. Results. A year after CABG surgery, 45% of patients showed positive dynamics or stable normal CAVI values. Death from all causes was significantly more common in the group with CAVI progression - 32 (27.6%) than in the group with CAVI improvement - 14 (14.8%; p = 0.029). Patients with CAVI progression were more likely to have MACE (death, MI, stroke/TIA) in 49 (42.2%) cases, compared with patients with CAVI improvement - in 23 (24.5%; p=0.008). Negative dynamics of CAVI (p = 0.024), number of shunts (p = 0.006), and the presence of carotid stenosis more than 30% (p = 0.051) were independent predictors of death from all causes at 10-year follow-up after CABG. The presence of carotid stenosis more than 30% (p = 0.002) and the group with negative dynamics of CAVI after a year (p = 0.008) were independent predictors of the development of the combined endpoint during long-term follow-up. Conclusions. Patients with negative dynamics of CAVI one year after CABG were more likely to experience death from all causes and combined endpoint in the long-term follow-up than patients with normal CAVI. In further studies, it is advisable to evaluate the dynamics of CAVI and, based on this, identify the most effective interventions to improve the prognosis of patients after CABG.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.