This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

Motion related human activity recognition using wearable sensors can potentially enable various useful daily applications. So far, most studies view it as a stand-alone mathematical classification problem without considering the physical nature of human motions. Consequently, they suffer from data dependencies and encounter the dimension disaster problem and the over-fitting issue, and their models are never human-readable. In this study, we start from a deep analysis on natural physical properties of human motions, and then propose a useful feature selection method to quantify each feature's classification contribution capability. On one hand, the "dimension disaster" problem can be avoid to some extent, due to the affined dimension of key features; On the other hand, over-fitting issue can be depressed since the knowledge implied in human motions are nearly invariant, which compensates the possible data inadequacy. The experiment results indicate that the proposed method performs superior to those adopted in related works, such as decision tree, k-NN, SVM, neural networks.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

Cloud-induced atmospheric extinction and occlusion have a major effect on the effectiveness and quality of telescope observations. Real-time cloud cover distribution and long-term statistical data are essential for astronomical siting and telescope operations. At ground-based astronomical telescope sites, cloud cover distribution is currently analyzed using manual observation methods. However, the main disadvantages of manual observation methods are human subjective, heavy workloads and poor real-time performance. Therefore, a real-time automatic cloud images classification method is desperately needed. This paper presents a new cloud identification method, which is named PSO+XGBoost model by combining eXtreme Gradient Boosting (XGBoost) and Particle Swarm Optimization (PSO). The entire cloud image is divided into 37 sub-regions in order to more precisely identify the distribution of the clouds. 19 features are then extracted, including the sky background, star density, lighting conditions, and subregion grayscale values. The experimental results have shown that the overall classification accuracy of 96.91% and our model is able to outperform several state-of-the-art baseline methods. Our approach achieves high accuracy in comparison with the manual observation methods. Moreover, this method meets telescope real-time scheduling requirements.

Fuzzy Rule Interpolation (FRI) offers an innovative methodology for inferring outcomes from data points that match no established rules in a sparse fuzzy rule base. Generally, a traditional fuzzy rule-based system suffers from the inability to perform inference while facing an unmatched observation, given a sparse fuzzy rule base that is derived from insufficient data or inadequate human experience and that fails to cover parts of a specific problem domain. Fortunately, starting with a sparse rule base, Fuzzy Rule Interpolation (FRI) can help to formulate interpolated rules specifically in instances where observations fail to activate any existing rule. An interpolated rule gives a result called consequent, which is related to the unmatched observation so that the inference system will not fail to generate an outcome corresponding to the observation as the output. Conventionally, these interpolated rules will be discarded after obtaining outcomes. However, valuable information may be potentially embedded within those discarded rules addressing the limitation regarding the coverage of the original sparse knowledge space. Moreover, without exploiting the potential value of the interpolated rules, the fuzzy inference system based on a sparse rule base will never improve its efficiency and robustness in the long run. Therefore, this underscores the necessity for Dynamic Fuzzy Rule Interpolation (D-FRI), which aims to collate interpolated rules that cover particular knowledge spaces absent in the sparse rule base. Intuitively, those frequently appeared interpolated rules are considered valuable because future observations are more likely to hit the respective problem areas. Promoting selected interpolated rules to the sparse rule base can enhance the overall coverage of the knowledge space and increase the inference efficiency over time. This paper introduces a framework for Dynamic Fuzzy Rule Interpolation that integrates the widely used Transformation-based Fuzzy Rule Interpolation (T-FRI) with an effective form of clustering of interpolated results. Experimental findings validate the effectiveness of this approach.

This work presents a novel approach for the study of the movement of droplets on inclined surfaces under the influence of gravity and chemical heterogeneities. The developed numerical methodology uses data-driven modeling to extend the applicability limits of an analytically derived reduced-order model for the contact line velocity. More specifically, while the reduced-order model is able to capture the effects of the chemical heterogeneities to a satisfactory degree, it does not account for gravity. To alleviate this shortcoming, datasets generated from direct numerical simulations are used to train a data-driven model for the contact line velocity, which is based on the Fourier neural operator and corrects the reduced-order model predictions to match the reference solutions. This hybrid surrogate model, which comprises of both analytical and data-driven components, is then integrated in time to simulate the droplet movement, offering a speedup of five orders of magnitude compared to direct numerical simulations. The performance of this hybrid model is quantified and assessed in different wetting scenarios, by considering various inclination angles and values for the Bond number, demonstrating the accuracy of the predictions as long as the adopted parameters lie within the ranges considered in the training dataset.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

Intrahepatic cholangiocarcinoma (ICCA) is a malignant epithelial neoplasm characterized by biliary differentiation within the liver. ICCA is molecularly heterogeneous and exhibits a broad spectrum of histopathological features. It is a highly aggressive carcinoma with high mortality and poor survival rates. ICCAs are classified into two main subtypes: small duct type and large duct types. These two tumor types have different cell origins and clinicopathological features. ICCAs are characterized by numerous molecular alterations, including mutations in KRAS, TP53, IDH1/2, ARID1A, BAP1, BRAF, SAMD4, and EGFR, and FGFR2 fusion. Two main molecular subtypes–inflammation and proliferation–have been proposed. Recent advances in high-throughput assays using next-generation sequencing have improved our understanding of ICCA pathogenesis and molecular genetics. The diagnosis of ICCA poses a significant challenge for pathologists because of its varied morphologies and phenotypes. Accurate diagnosis of ICCA is essential for effective patient management and prognostic determination. This article provides an updated overview of ICCA pathology, focusing particularly on molecular features, histological subtypes, and diagnostic approaches.

Due to the rapid development of unmanned aerial vehicles (UAVs) communication technology, UAVs are gradually competing with primary users (PUs) for spectrum resources. Cognitive radio (CR) is a promising solution to meet the needs. Cooperative spectrum sensing (CSS) is considered as an effective method to detect the PU signal and identify available spectrum resources for UAVs in a cognitive UAV network (CUAVN). However, the cooperative mode among multiple UAVs may incur a high overhead, resulting in performance degradation. Therefore, we introduce a differential sequential 1 (DS1), which incorporates a differential mechanism and leverages the sequential idea based on the classical voting rule to enhance cooperative performance and efficiency. In view of this, we formulate three scenarios to characterize the PU activity and introduce a multi-slot cooperative mode within a single UAV to realize cooperative gain. Further, only the information change about the PU status is sequentially calculated in DS1, and combined with a sequential idea, the efficiency of the voting rule is greatly improved. Moreover, the application of support vector machines (SVM) in dynamic selection enables the selection of the most suitable voting rule based on diverse sensing parameters. This dynamic selection process ensures optimal performance and efficiency by adapting the voting rule to the specific characteristics of the given scenario. Finally, simulation results demonstrate that the superiority of our proposal with respect to the detection performance, sample size and the energy efficiency is evident, which proves the high performance of the proposed policy.

Detection of subsurface archaeological remains using a range of remote sensing methods, poses several challenges until today. Recent studies regarding the detection of archaeological proxies like those of cropmarks highlight the complexity of the phenomenon. In this work we present three different methods, and associated indices, for identifying stressed reflectance signatures indicating buried archaeological remains, based on a dataset of measured ground spectroradiometric reflectance. Several spectral profiles between the visible and near infrared part of the spectrum, were taken over a controlled environment in Cyprus during the 2011-2012 and are re-used in this study. The first two (spectral) methods are based on a suitable analysis of the spectral signatures in (1) the visible part of the spectrum, and in particular in the neighborhood of 570 nm, and (2) the red edge-near infrared part of the spectrum, in the neighborhood of 730 nm. Machine learning (decision trees) allows for the deduction of suitable wavelengths to focus on, in order to formulate the proposed indices and the associated classification criteria (decision boundaries) that can enhance the detection probability of stressed vegetation. Noise in the signal is taken into account by simulating reflectance signatures perturbed by white noise. Applying decision tree classification on the ensemble of simulations and basic statistical analysis we refine the formulation of the indices and criteria for the noisy signatures. The success rate of the proposed methods is over 90%. The third method rests on the estimation of vegetation/canopy reflectance parameters through inversion of the physical-based PROSAIL reflectance model and the associated classification through machine learning methods. The obtained results provide further insights into the formation of stress vegetation that occurred due to the presence of shallow buried archaeological remains, which are well aligned with physical-based models and existing empirical knowledge. To the best of the authors' knowledge, this is the first study demonstrating the usefulness of radiative transfer models such as PROSAIL for understanding the formation of cropmarks. Similar studies can support future research directions towards the development of regional remote sensing methods and algorithms if systematic observations are adequately dispersed in space and time.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

This work addresses the lot-sizing and production scheduling problem of multi-stage multi-product food industrial facilities. More specifically, the production scheduling problem of the semi-continuous yogurt production process, for two large-scale Greek dairy industries, is considered. Production scheduling decisions are taken using two approaches: i) an optimization and ii) a rule-based approach, followed by a comparative study. A MILP model is applied for the optimization of short-term production scheduling of the two industries. Then, the same problems are solved using the commercial scheduling tool ScheduleProTM, which derives scheduling decisions, using simulation-based techniques and empirical rules. It is concluded that both methods, despite having their advantages and disadvantages, are suitable for addressing complex food industrial scheduling problems. The optimization-based approach leads to better results in terms of operating cost reduction. On the other hand, the complexity of the problem and the experience of production engineers and plant operators can significantly impact the quality of the obtained solutions for the rule-based approach.

Background: Circulating rare cells participate in breast cancer evolution as systemic components of the disease and thus, are a source of theranostic information. Exploration of cancer-associated rare cells is in its infancy. We determined the validity of a rare-cell detection platform and demonstrated the usefulness of a certain rare cell subset as a novel approach to characterize the breast cancer system. Methods: Linearity of the Rarmax® platform was established using a spike-in approach. The platform includes red blood cell lysis, leukocyte depletion and high-resolution fluorescence image recording. Rare cell analysis was conducted on 28 samples (before and after surgery) from 14 patients with breast cancer, 20 healthy volunteers and 9 non-cancer control volunteers. In-depth identification of rare cells, including circulating tumor cells, endothelial-like cells, erythroblasts and inflammation-associated cells, was performed using a phenotype and morphology-based classification system. Results: The platform performed linearly over a range of 5-950 spiked cells, with an average recovery of 84.6%. Circulating epithelial and endothelial-like cell subsets have been demonstrated to be associated with or independent of cancer with tumor presence. Furthermore, certain cell patterns may be associated with treatment-related adverse effects. The sensitivity in detecting tumor-presence and cancer-associated abnormality before surgery was 50% and 85.7%, respectively and the specificity was 100% and 96.6%, respectively. Conclusion: The present study supports the idea of a cancer-associated rare cell abnormality to represent tumor entities as well as systemic cancer. The latter is independent of the apparent clinical cancer.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Various factors and constraints should be considered when developing a manufacturing production schedule, and such a schedule is often based on rules. This paper develops a composite dispatching rule based on heuristic rules that comprehensively consider various factors in a semiconductor production line. The composite rule is obtained by exploring various states of a semiconductor production line (machine status, queue size, etc.), where such indicators as makespan and equipment efficiency are used to judge performance. A model of the response surface, as a function of key variables, is then developed to find the optimized parameters of a composite rule for various production states. Further, dynamic scheduling of semiconductor manufacturing is studied based on support vector regression (SVR). This approach dynamically obtains a composite dispatching rule (i.e. parameters of the composite dispatching rule) that can be used to optimize production performance according to real-time production line state. Following optimization, the proposed dynamic scheduling approach is tested in a real semiconductor production line to validate the effectiveness of the proposed composite rule set.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

Many types of banana (Musa spp.)—one of the most economically important horticultural crops—exist, and their ploidy (diploid, triploid, and tetraploid, usually) and genome types (containing A or/and B genome in most cases) differ. At present, observation and genome type detection are commonly used to identify banana germplasm resources. However, the former is tedious, while the latter cannot distinguish categories below genome types. It is therefore urgent that a simple and effective method for identifying banana germplasm resources is established. We sequenced and analyzed the ribosomal DNA internal transcribed spacer (ITS) sequences of 62 banana germplasm and found that the sequencing peaks, especially the 20 bp region near the 420 bp position (referred to as the “420 bp region”), exhibited relatively recognizable and repeatable polymorphism characteristics. Using the “420 bp region” as a marker, we were able to quickly distinguish bananas belonging to different genome type groups (comprising the AA, AB, AAA, ABB, AAB, ABBB, AAAB, and AAAA groups) or different subgroups in the same genome type group (for example, the Cavendish, Gros Michel, Red, Lakatan, and Ibota Bota subgroups in the AAA group; and the Pisang Raja, Plantain, Pome and Silk subgroups in the AAB group). Moreover, it appeared that Sanger sequencing of ITS could be used for identifying banana hybrid offspring. These results demonstrated that the banana ITS region contains rich genetic information that is useful for genotyping. In general, ITS sequencing simplifies the classification of banana germplasm resources and has potential application in several areas of Musa improvement.

In this paper, inspired by Jleli and Samet [journal of inequalities and applications 38 (2014) 2 1–8] we introduce two new classes of auxiliary functions and utilize the same to define (q, y)R-weak 3 contractions. Utilizing (q, y)R-weak contractions, we prove some fixed point theorems in the setting 4 of relational metric spaces. We employ some examples to substantiate the utility of our newly proved 5 results. Finally, we apply one of our newly proved results to ensure the existence and uniqueness of 6 solution of a Volterra-type integral equation.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

The objective of this study was to compare the pathogens and susceptibilities of the current automated rule-based technology (RBT) antibiogram with one manually collected through chart review with additional rules applied. This study was a 2-year, retrospective cohort study and included all bacterial cultures within the first 30 days from patients admitted to a single Burn Center. The current RBT antibiogram served as the control and new antibiogram versions were created using additional rules and compared to the control. Six-hundred fifty-seven patients were admitted (61% excluded for lack of cultures). Fifty-nine percent had at least one hospital acquired risk factor with over one-third having recent illicit drug use and one-third having a recent hospitalization. Of the 410 cultures included, 57% were Gram-negative and half were from wound infections. Sensitivities were significantly different when comparing manual and the RBT version after including factors, such as days since admission, presence of hospital acquired risk factors, or previous antibiotic courses. Recommended empiric Gram-negative antibiotics changed from double coverage to a single β-lactam with > 90% susceptibility. The susceptibilities between first and subsequent courses were dramatically different. Before developing an antibiogram or interpreting the output, it is important to consider which automated criteria are utilized, especially for units with extended lengths of stay.

In this paper, we propose an imagined speech-based brain wave pattern recognition using deep learning. Multiple features were extracted concurrently from eight-channel Electroencephalography (EEG) signals. To obtain classifiable EEG data with fewer number of sensors, we placed the EEG sensors on carefully selected spots on the scalp. To decrease the dimensions and complexity of the EEG dataset and to avoid overfitting during the deep learning algorithm, we utilized the wavelet scattering transformation. A low-cost 8-channel EEG headset was used with MATLAB 2023a to acquire the EEG data. The Long-Short Term Memory Recurrent Neural Network (LSTM-RNN) was used to decode the identified EEG signals into four audio commands: Up, Down, Left, and Right. Wavelet scattering transformation was applied to extract the most stable features by passing the EEG dataset through a series of filtration processes. Filtration has been implemented for each individual command in the EEG datasets. The proposed imagined speech-based brain wave pattern recognition approach achieved a 92.50% overall classification accuracy. This accuracy is promising for designing a trustworthy imagined speech-based Brain-Computer Interface (BCI) future real-time systems. For better evaluation of the classification performance, other metrics were considered, and we obtained 92.74%, 92.50% and 92.62% for precision, recall, and F1-score, respectively.

Linear programming formulations of forest ecosystem management (FEM) problems proposed in the 60s have been adapted and improved upon over the years. Generating management alternatives for forest management planning is a key step in building these models. Global forests are diverse, and a variety of models have been developed to simulate management alternatives. Climate change has made forest management calculations even more complex, requiring flexibility, diverse parameters, models, and methods. Despite this complexity, consistent concepts can be applied in developing management alternatives for forest management planning. This work describes iGen, a flexible forest prescription generator that applies the AI technique Rule-Based System (AI-RBS). iGen projects the state and associated inputs and outputs for a set of management units using rules from its knowledge base. An Inference Engine uses the rules to simulate a set of prescriptions in a tree-like graph structure. Without needing IT specialists, forest managers can describe the potential development of their forest through variables, rules, formulas, functions, and procedures. A key feature of iGen is that it is not limited to, adapted to, or focused on any specific region, landscape, forest condition, projection method, or yield function. Instead, it aims to maximize generality, enabling it to address a broad range of FEM problems. This article introduces iGen, explaining its concepts, structure, and algorithms through two FEM problems: natural regeneration with shelterwood harvests and plantation/coppice. For data and iGen source programs, visit github.com/…/iGen.

Domain generalization has led to remarkable achievements in Hyperspectral Image (HSI) classification. Inspired by contrastive language-image pre-training (CLIP), the language-aware domain generalization method has been explored to learn cross-domain-invariant representation. However, existing methods face some challenges: 1) The weak capacity to extract long-range contextual information and inter-class correlation. 2) Due to the inadequacies of the large-scale pre-training for HSI data, the spatial-spectral features of HSI and linguistic features can not be straightforwardly alignment. To address the above problems, a novel network has been proposed with a CLIP framework, which consists of an image encoder, based on an encoder-only transformer to obtain the global contextual information and inter-class correlation, a frozen text encoder, and a cross-attention mechanism, named Linguistic-Interact-with-Visual Engager (LIVE), enhances the interaction between two modalities. Extensive experiments demonstrating superior performance over state-of-the-art methods in HSI Domain Generalization with a CLIP framework.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

We present a simplified computational rule for the back-propagation formulas for artificial neural networks. In this work, we provide a generic two-step rule for the back-propagation algorithm in matrix notation. Moreover, this rule incorporates both the forward and backward phases of the computations involved in the learning process. Specifically, this recursively computing rule permits the propagation of the changes to all synaptic weights in the network, layer by layer, efficiently. In particular, we use this rule to compute both the up and down partial derivatives of the cost function of all the connections feeding into the output layer.

Convolutional Neural Networks (CNNs) are often criticized for their lack of transparency, acting as 'black boxes' in decision-making, a challenge compounded by class imbalance in ECG datasets, which limits their clinical application. This study introduces a CNN-based ECG signal classification model that enhances interpretability and addresses class imbalance through the Synthetic Minority Over-sampling Technique (SMOTE). The model also integrates Uniform Manifold Approximation and Projection (UMAP) for dimensionality reduction and SHAP value analysis, facilitating the visualization of decision boundaries and the assessment of feature contributions. Our evaluation using the MIT-BIH Arrhythmia Database highlights the model's high performance, with accuracy and precision nearing 1.00 for Normal ECG (NOR), Left Bundle Branch Block (LBBB), Right Bundle Branch Block (RBBB), and Ventricular Premature Beat (PVC) in the six-class task. In the ten-class task, the model demonstrated robustness, particularly with an accuracy of 0.9846, precision of 0.9783, recall of 0.9736, and F1 score of 0.9760 in Pacemaker Fusion Beat (PFHB), supported by an AUC of 0.9999 and AP of 0.9885. These results underscore the model's efficacy in cardiac rhythm recognition and resilience to class imbalance. Future research will explore sophisticated model architectures and feature extraction methods to enhance the model's generalization and clinical applicability for early heart disease diagnosis and personalized treatment.

Efficient quality evaluation provides support for the timely and good maintenance of the lane line marking. This paper searches and optimizes the back propagation(BP) network model which referred to the analytic hierarchy process(AHP) model structure, as well as the number of nodes in the middle layer network. Based on this, a comprehensive evaluation method of multi-dimensional lane line quality such as shape, color and contrast is established. The experimental results show that the parameters of the model are more simplified, and the scoring and classification results of lane lines are more accurate.

We have shown in previous work that the equivalence of the Heisenberg and Schrödinger pictures of quantum mechanics requires the use of the Born and Jordan quantization rules. In the present work we give further evidence that the Born--Jordan rule is the correct quantization scheme for quantum mechanics. For this purpose we use correct short-time approximations to the action functional, initially due to Makri and Miller, and show that these lead to the desired quantization of the classical Hamiltonian.

Object classification is a crucial task in deep learning, which involves the identification and categorization of objects in images or videos. Although humans can easily recognize common objects, such as cars, animals, or plants, performing this task on a large scale can be time-consuming and error-prone. Therefore, automating this process using neural networks can save time and effort while achieving higher accuracy. Our study focuses on the classification step of human chromosome karyotyping, an important medical procedure that helps diagnose genetic disorders. Traditionally, this task is performed manually by expert cytologists, which is a time-consuming process that requires specialized medical skills. Therefore, automating it through deep learning can be immensely useful. To accomplish this, we implemented and adapted existing preprocessing and data augmentation techniques to prepare the chromosome images for classification. We used ResNet-50 convolutional neural networks and an ensemble approach to classify the chromosomes, obtaining state-of-the-art performance in the tested dataset.

We present a new unsupervised method aimed to obtain a partition of a complex urban system in homogenous urban areas, called urban contexts. The area of study is initially partitioned in microzones, homogeneous portion of the urban system, that are the atomic reference elements for the census data. With the contribution of domain experts, we identify the physical, morphological, environmental and socio-economic indicators need to identify synthetic characteristics of urban contexts and create the fuzzy rule set necessary to determine the type of urban context. We implement the set of spatial analysis processes necessary to calculate the indicators for microzone and apply a Mamdani fuzzy rule system to classify the microzones. Finally, the partition of the area of study in urban contexts is obtained by dissolving continuous microzones belonging to the same type of urban context. Tests are performed on the Municipality of Pozzuoli (Naples - Italy); the reliability of out model is measured by comparing the results with the ones obtained by detailed analysis.

Sentiment analysis plays a crucial role in understanding customer feedback, guiding product development, and informing business decisions. This paper introduces term sentiment entropy (TSE), a novel weighting method that leverages the distribution of sentiment labels associated with words to enhance text classification accuracy. TSE complements traditional TF-IDF techniques by capturing the nuances of sentiment variation across different contexts. Experiments across diverse public datasets demonstrate TSE's potential to improve sentiment analysis performance, especially in capturing subtle sentiment shifts and adapting to specific domains. While computational cost and label quality pose challenges, TSE offers a promising avenue for refining sentiment analysis and opening new research frontiers.

The exponential growth of digital media content has introduced new challenges in managing and classifying internet traffic. Digital media traffic is composed of various applications such as video, audio, social media, and search, and its data structure is complex, incorporating a vast array of features. The classification of traffic data is a crucial aspect of internet traffic management and network security, and it forms the basis for several scenarios, including content distribution, advertising recommendations, and data analysis. Traditional classification methods rely mainly on deep packet inspection and port-based techniques, which have become increasingly ineffective due to the rapid evolution of network traffic. To address this issue, this study proposes a machine learning-based traffic classification method aimed at enhancing the accuracy and efficiency of digital media traffic classification to meet the current needs of traffic management and network security. The paper also analyzes and evaluates the classification effect and prediction capability of various algorithms under different training set sizes to validate the feasibility and effectiveness of the proposed method. The result demonstrates that the neural network algorithm has superior classification and prediction capabilities compared to the decision tree and support vector machine algorithms. Furthermore, our proposed method achieves the highest accuracy of 96.88% with a large training sample of 40,000 data streams, proving its superiority in handling high-dimensional data and complex datasets. The research results are significant for the development of digital media traffic classification and prediction methods and are expected to be applied in practical scenarios.

Emotions are indicators of affective states and play a significant role in human daily life, behavior, and interactions. Giving emotional intelligence to the machines could, for instance, facilitate early detection and prediction of (mental) diseases and symptoms. Electroencephalography (EEG) -based emotion recognition is being widely applied because it measures electrical correlates directly from the brain rather than the indirect measurement of other physiological responses initiated by the brain. The recent development of non-invasive and portable EEG sensors makes it possible to use them in real-time applications. Therefore, this paper presents a real-time emotion classification pipeline, which trains different binary classifiers for the dimensions of Valence and Arousal from an incoming EEG data stream. After achieving a 23.9% (Arousal) and 25.8% (Valence) higher f1-score on the state-of-art AMIGOS dataset, this pipeline was applied to the dataset achieved by an emotion elicitation experimental framework developed within the scope of this thesis. Following two different protocols, 15 participants were recorded using two different consumer-grade EEG devices while watching 16 short emotional videos in a controlled environment. For an immediate label setting, the mean f1-score of 87% and 82% were achieved for Arousal and Valence, respectively. In a live scenario, while continuously being updated on the incoming data stream with delayed labels, the pipeline proved to be fast enough to achieve predictions in real time. However, the significant discrepancy from the readily available labels on the classification scores leads to future work to include more data with frequent delayed labels in the live settings.

Embedding representation models characterize each word as a vector of numbers with a fixed length. These models have been used in tasks involving text classification, such as recommen- dation and question-answer systems. Semantic relationships are words with a relationship between them providing a complete idea to a text. Therefore, it is hypothesized that an embedding model involving semantic relationships will provide better performance for tasks that use them. This paper presents three embedding models based on semantic relations extracted fromWikipedia to classify texts. The synonym, hyponym, and hyperonym semantic relationships were the ones considered in this work since previous experiments have shown that they are the ones that provide the most semantic knowledge. Lexical-syntactic patterns present in the literature were implemented and subsequently applied to the Wikipedia corpus to obtain the semantic relationships present in it. Several semantic relationships are used in different models: synonymy, hyponym-hyperonym, and a combination of the first two. A convolutional neural network was trained for text classification to evaluate the performance of each model. The results obtained were evaluated with the metrics of precision, accuracy, recall, and F1-measure. The best values obtained with the second model were accuracy of 0.79 for the 20-Newsgroup corpus. F1-measure and recall of 0.87 respectively for the Reuters corpus.

In order to achieve the elimination of the negative impacts of transport on road safety, the European Union is taking various measures resulting from its commitment to improve road safety. One of the instruments for achieving the objectives set is social legislation for the work of drivers in road freight and passenger transport. In line with the objective of improving the quality of working conditions for road transport drivers and road safety, the European Union applies Regulation (EC) No 561/2006 on the harmonisation of certain social legislation relating to road transport, which lays down rules on driving times, breaks and rest periods for drivers operating in road freight and passenger transport. The main objective of the paper is to assess the impact of social legislation on road transport safety by means of real research and to identify the factors influencing the violation of the legislation depending on the type of transports carried out in domestic or international road freight transport.

Nowadays, in low voltage (LV) electric distribution networks (EDNs), the Distribution Network Operators (DNOs) are encountering a high number of connected small-scale distributed generation units, mainly photovoltaic (PV) prosumers. The irregular behavior of the prosumers, together with the uncertainty degree of the requested and injected powers associated with all end-users from the LV EDN, can cause voltage variations with violations of the allowable limits. In this context, the paper developed an efficient and resilient expert system integrating the rule-based reasoning applied to the On-load Tap Changer (OLTC)-fitted transformer to improve the efficiency of the voltage control in the PV-rich LV EDNs. An in-depth analysis based on 75 scenarios, resulting from the combinations of three indicators: the penetration degree of the PV prosumers, consumption evolution associated with the consumers, and energy production of the PV systems, has been performed to demonstrate the efficiency of the proposed expert system in an LV EDN from a rural area belonging to a Romanian DNO. The success rate of the expert system has been 86.7% (65 out of 75 scenarios didn't have voltage issues, all values being between the allowable limits in 100% of the time slots associated with the analyzed period). For the other scenarios (representing 13.3%), the values have been inside the range [-10%, +10%] at least 95% of the time slots, according to the European Power Quality Standard, and for the rest of the time slots up to 100% being very close to the upper and lower limits of the range, with highly mitigating of the voltage variations.

Due to the special characteristics of the shooting distance and angle of remote sensing satellites, the pixel area ratio of ship targets is small and the feature expression is insufficient, which leads to unsatisfactory ship detection performance and even situations such as missed detection and false detection. In this study, we propose an improved-YOLOv5 algorithm. The improvement strategies mainly include: (1) Add the Convolutional Block Attention Module (CBAM) into the Backbone to enhance the extraction of target-adaptive optimal features; (2) Introduce cross-layer connection channel and lightweight GSConv structure into the Neck to achieve higher-level multi-scale feature fusion and reduce the number of model parameters; (3) The Wise-IoU loss function is used to cal-culate the localization loss in the Output, and assign reasonable gradient gains to cope with dif-ferences in image quality. In addition, during the preprocessing stage of experimental data, a me-dian and bilateral filter method is used for noise reduction to reduce interference from ripples and waves and highlight the information of ship features. The experimental results show that Im-proved-YOLOv5 has a significant improvement in recognition accuracy compared to various mainstream target detection algorithms; Compared to the original YOLOv5s, the mean Average Precision (mAP) has improved by 3.2% and the Frames Per Second (FPN) has accelerated by 8.7%.

Background: Risk tratification based on pre-test probability may improve the diagnostic accuracy of temporal artery high-resolution compression sonography (hrTCS) in the diagnostic workup of cranial giant cell arteriitis (cGCA). Methods: A logistic regression model with candidate items was derived from a cohort of patients with suspected cGCA (n = 87). The diagnostic accuracy of the model was tested in the derivation cohort and in an independent validation cohort (n = 114) by receiver operator characteristics (ROC)-analysis. The clinical items were composed to a clinical prediction rule, integrated into a stepwise diagnostic algorithm together with CRP-values and hrTCS-values. Results: The model consisted of 4 clinical variables (age > 70, headache, jaw claudication, anterior ischemic optic neuropathy). The diagnostic accuracy of the model for discrimination of patients with and without a final clinical diagnosis of cGCA was excellent in both cohorts (AUC 0.96 and AUC 0.92, respectively). The diagnostic algorithm improved the positive predictive value of hrCTS substantially. Within the algorithm, 32.8% of patients (derivation cohort) and 49.1% (validation cohort) would not have been tested by hrtCS. None of these patients had a final diagnosis of cGCA. Conclusion: A diagnostic algorithm based on a clinical prediction rule improves the diagnostic accuracy of hrTCS.

We have shown that according to the predictions of the standard quantum theory, signaling is possible using a postponed compensation Hong-Ou-Mandel interferometer, although it violates Lorentz invariance. We argue that new physics is required to deal with such a paradox. Either quantum principles or relativity needs reassessment. We propose an experiment that can decide whether relativity rules over quantum or vice versa.

The lack of a uniform approach in Earth and planetary science is apparent in the current levels of inconsistency found within the research itself, the data analysis and the interpretation of results. Thus, data interpretation differ depending on whether the study refer to Earth conditions or from space. These differences are particularly pronounced for cryosphere studies, where geocentric approaches remain within ice research and its application in analogical studies. Here, the principle of spatial uniformitarianism is presented, to allow for a definitive departure from geocentrism and a proper understanding of the role of ice within both the Earth and celestial bodies. At the practical level, it may affect several geo-scientific disciplines currently inconsistent and bridging the gap among them. This rule is universal and complements the Hutton-Lyell 1795/1830 principle.

Abstract:The objects of fine-grained image categories(e.g., bird species) are various subclass under different categories. Because the differences between subclass are very subtle and most of them are concentrated in multiple local areas, the task of fine-grained image recognition is very challenging. At the same time, some fine-grained networks tend to focus on a certain region when judging the target category, resulting in the lack of other auxiliary regional features. To this end, Inception V3 is used as the backbone network, and an enhanced and complementary fine-grained image classification network is designed. While adopting the method of reinforcement learning to obtain more detailed fine grain image features, the complementary network can obtain the complementary discriminant area of the target through the method of attention erasure to increase the network's perception of the overall target. Finally, experiments are conducted on CUB-200-2011, FGVC Aircraft and Stanford dogs three open datasets. The experimental results show that the proposed model has better performance.

This paper presents a novel method for automatic modulation classification (AMC) for cognitive radio (CR) networks based on a simple classifier that is trained with high-order cumulant. The proposed method focuses on the statistical behavior of modulated signals and includes analog modulation and digital schemes, which received less attention in the literature. The effectiveness of the proposed method is demonstrated through simulation results using high-quality generated signals under different signal-to-noise ratios (SNRs) and channel conditions. The classification performance achieved by the proposed method is superior to that of the more complex deep learning methods, making it well-suited for deployment in end units of CR networks, particularly in military and emergency service applications. The proposed method offers a cost-effective, high-quality solution for AMC that meets the stringent requirements of these critical applications.

Commercial banks usually classify customers according to their credit reports when making loans. In this study, we put our focus on classifying customers based on their credit reports from the People's Bank of China (PBC). Since there are no target labels of users in the credit report of the People's Bank of China, we put forward the fuzzy clustering method for the initial label, and then Construct ant colony search to optimize intelligent recognition. Finally, this study uses SVM, BP neural network, and random forest to classify users and compare their results. The research re-sults indicate that using ant colony clustering algorithm and random forest for classification is the most effective method with the PBC credit reports.

Blood cell analysis is a crucial diagnostic process in medical practice. In particular, detecting white blood cells (WBCs) is essential for diagnosing of many diseases. The manual screening of blood films is a time-consuming and subjective process, which can lead to inconsistencies and errors. Therefore, automated detection of blood cells can improve the accuracy and efficiency of the screening process. In this study, an explainable Vision Transformer (ViT) model was proposed for the automatic detection of WBCs from blood films. The proposed model utilizes the self-attention mechanism to extract relevant features from the input images and leverages transfer learning by incorporating pre-trained model weights to improve its performance. The proposed model achieved a classification accuracy of 99.40% for five distinct types of WBCs and exhibited potential in reducing the time required for manual screening of blood films by pathologists. Upon examination of the misclassified test samples, it was observed that incorrect predictions were correlated with the presence or absence of granules in the cell samples. To validate this observation, the dataset was divided into two classes, namely Granulocytes and Agranulocytes, and a secondary training process was conducted. The resulting ViT model trained for binary classification achieved an accuracy of 99.70%, recall of 99.54%, precision of 99.32%, and F-1 score of 99.43% during the test phase. To ensure the reliability of the ViT model's multi-class classification of WBCs, the pixel areas that the model focuses on in its predictions are visualized through the Score-CAM algorithm.

With the latest advances in information and communication technologies, greater amounts of sensitive user and corporate information are constantly shared across the network making it susceptible to an attack that can compromise data confidentiality, integrity and availability. Intrusion Detection Systems (IDS) are important security mechanisms that can perform a timely detection of malicious events through the inspection of network traffic or host-based logs. Throughout the years, many machine learning techniques have proven to be successful at conducting anomaly detection but only a few considered the sequential nature of data. This work proposes a sequential approach and evaluates the performance of a Random Forest (RF), a Multi-Layer Perceptron (MLP) and a Long-Short Term Memory (LSTM) on the CIDDS-001 dataset. The resulting performance measures of this particular approach are compared with the ones obtained from a more traditional one, that only considers individual flow information, in order to determine which methodology best suits the concerned scenario. The experimental outcomes lead to believe that anomaly detection can be better addressed from a sequential perspective and that the LSTM is a very reliable model for acquiring sequential patterns in network traffic data, achieving an accuracy of 99.94% and a f1-score of 91.66%.

Disease classification based on biological data is an important area in bioinformatics and biomedical research. It helps the doctors and medical practitioners for the early detection of disease and support them as a computer-aided diagnostic tool for accurate diagnosis, prognosis, and treatment of disease. Earlier Microarray gene expression data have wide application for the classification of disease, but now Next-generation sequencing (NGS) has replaced the Microarray technology. From the last few years, RNA sequence (RNA-Seq) data are widely used for the transcriptomic analysis. Hence, RNA-Seq based classification of disease is in its infancy. In this article, we present a general framework for the classification of disease constructed on RNA-Seq data. This framework will guide the researchers to process RNA-Seq, extract relevant features and apply the appropriate classifier to classify any kind of disease.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

ACL instability poses a significant challenge in traumatology and orthopedic medicine, often requiring accurate diagnosis for appropriate treatment. While the pivot-shift test offers a crucial means of assessment, its reliance on subjective interpretation underscores the need for supplementary imaging studies. This study aims to address this limitation by developing a Bayesian classification algorithm tailored for integration into a mobile application. Using the built-in inertial sensors of smartphones, this new approach aims to dynamically evaluate rotational stability during knee examinations. Orthopedic specialists conducted knee evaluations on 52 subjects, with subsequent analysis revealing interesting insights. Intraobserver and interobserver analyses, as measured by ICC, demonstrated strong agreement both in terms of timing between maneuvers (ICC = 0.94) and signal amplitude (ICC = 0.71-0.66). Notably, the Bayesian algorithm successfully classified 95% of joint hypermobility cases, with an additional 7 cases of hyperlaxity identified by the Pivot-Shift Meter (PSM). These findings highlight the practicality and effectiveness of implementing a Bayesian classification algorithm within a mobile application for assessing and categorizing signals captured by smartphone inertial sensors during the pivot-shift test.

Scator set, introduced by Fernández-Guasti and Zaldívar, is endowed with a very peculiar non-distributive product. In this paper we consider the scator space of dimension $1+2$ and the so called fundamental embedding which maps the subset of scators with non-zero scalar component into 4-dimensional space endowed with a natural distributive product. The original definition of the scator product is induced in a straightforward way. Moreove, we propose an extension of the scator product on the whole scator space, including scators with vanishing scalar component.

Background: Ongoing molecular profiling studies enabled by advances in biomedical technologies are producing vast amounts of ‘omic’ data for early detection, monitoring, and prognosis of diverse diseases. A major common limitation is the scarcity of biological samples, necessitating integrative modeling frameworks that can make optimal use of available data for disease classification tasks. Related data sets are often available from different studies, but may have been generated using different technology platforms. Thus, there is a critical need for flexible modeling methods that can handle data from diverse sources to facilitate the discovery of robust biomarkers that underlie disease regulatory processes. Results: In this paper, we introduce a novel framework called Knowledge Augmented Rule Learning (KARL), which incorporates two sources of knowledge, domain, and data, for pattern discovery from small and high-dimensional datasets, such as transcriptomic data. We propose KARL as a transfer rule learning framework in which knowledge of the domain is transferred to the learning process on data in order to 1) improve the reliability of the discovered patterns, and 2) study the knowledge of the domain when used along with data for modeling. In this work, we generated KARL models on gene expression datasets for five types of cancer, including brain, breast, colon, lung, and prostate. As our knowledge of the domain, we used the Ingenuity Knowledge Base (IKB) to extract genes related to hallmarks of cancer and annotated these prior relationships before learning classifiers from these datasets. Conclusions: Our results show that KARL produces, on average, rule models that are more robust classifiers than the baseline without such background knowledge, for our tasks of cancer prediction using 25 publicly available gene expression datasets. Moreover, KARL helped us learn insights about previously known relationships in these gene expression datasets, along with new relationships not input as known, to enable informed biomarker discovery for cancer prediction tasks. KARL can be applied to modeling similar data from any other domain and classification task. Future work would involve extensions to KARL to handle hierarchical knowledge to derive more general hypotheses to drive biomedicine.

In this study, a mixed rule of degree of precision nine has been developed and implemented in the field of electrical sciences to obtain the instantaneous current in the RLC- circuit for particular value .The linearity has been performed with the Volterra’s integral equation of second kind with particular kernel . Then the definite integral has been evaluated through the mixed quadrature to obtain the numerical result which is very effective. A polynomial has been used to evaluate Volterra’s integral equation in the place of unknown functions. The accuracy of the proposed method has been tested taking different electromotive force in the circuit and absolute error has been estimated.

Convolutional neural networks (CNNs) face challenges in capturing long-distance text correlations, and Bidirectional Long Short-Term Memory (BiLSTM) networks exhibit limited feature extraction capabilities for text classification of work order. To address the abovementioned problems, this work utilizes an ensemble learning approach to integrate model elements efficiently. This study presents a method for classifying work order texts using a hybrid neural network model called BERT-BiLSTM-CNN. First, use Bert for preprocessing to obtain text vector representations. Then, capture context and process sequence information through BiLSTM. Next, capture local features in the text through CNN. Finally, obtain classification results through Softmax. Through comparative analysis, the method of fusing these three models is superior to other hybrid neural network model architectures in multiple classification tasks. It has a significant effect on work order classification.

In recent years, there has been significant growth in the ubiquity and popularity of three dimensional(3D) point clouds, with an increasing focus on the classification of 3D point clouds. To extract richer features from point clouds, many researchers have turned their attention to various point set regions and channels within irregular point clouds. However, this approach has limited capability in attending to crucial regions of interest in 3D point clouds and may overlook valuable information from neighboring features during feature aggregation. Therefore, this paper proposes a novel 3D point cloud classification method based on global attention and adaptive graph convolution. The method consists of two main branches: the first branch com-putes attention masks for each point, while the second branch employs adaptive graph convolu-tion to extract global features from the point set. It dynamically learns features based on point interactions, generating adaptive kernels to effectively and precisely capture diverse relationships among points from different semantic parts. Experimental results demonstrate that the proposed model achieves 93.8% in overall accuracy and 90.8% in average accuracy on the ModeNet40 dataset.

Convolutional neural networks (CNN) have attracted much attention as a commonly used method for hyperspectral image (HSI) classification in recent years, however, CNNs can only be applied to Euclidean data and have limitations in dealing with relationships due to the limitations of local feature extraction. However, each pixel of a hyperspectral image contains a set of spectral bands that are correlated and interact with each other, and the methods used to process Euclidean data cannot effectively obtain these correlations. In contrast, the graph convolutional network (GCN) can be used in non-Euclidean data, but usually leads to oversmoothing and ignoring local detail features due to the need for superpixel segmentation processing to reduce computational effort. To overcome the above problems, we constructed a network a fusion network based on GCN and CNN, which contains two branches: a graph convolutional network based on superpixel segmentation and a convolutional network with added attention mechanism. The graph convolu-tional branch can extract the structural features and capture the relationships between the nodes, and the convolutional branch can extract the detailed features in the local fine region. Owing to the fact that the features extracted from the two branches are different, the classification performance can be improved by fusing the complementary features extracted from the two branches. To vali-date the proposed algorithm, experiments were conducted on three widely used datasets, namely Indian Pines, Pavia University, and Salinas, and the overall accuracy of 98.78% was obtained in the Indian Pines dataset, and the overall accuracy of 98.99% and 98.69% was obtained in the other two datasets. The results showed that the proposed fusion network can obtain richer features and achieve high classification accuracy.

Data can be illustrated in shapes, and the shapes could provide insight for data modeling and information extraction. Topological data analysis provides an alternative insight in biomedical data analysis and knowledge discovery with the algebra topology tools. In present work, we study the application of topological data analysis for personalized electrocardiographic signal classification toward arrhythmia analysis. Using phase space reconstruction technique, the signal samples are converted into point clouds for topological analysis facility. With topological techniques the persistence landscapes from the point clouds are extracted as features to perform the arrhythmia classification task. We find that the proposed method is robust to the training set size, with only a training set size of 20% percents, the normal heartbeat class are 100% recognized, ventricular beats for 97.13%, supra-ventricular beats for 94.27% and fusion beats for 94.27% within the corresponding experiments. The property of keeping high performance when using smaller training sample proves that the proposed method is especially applicable to personalized analysis. With the present study, we show that the topological data analysis technique could be a useful tool in biomedical signal analysis, and provide powerful ability in personalized analysis.

Structural magnetic resonance imaging (sMRI) is widely used in the clinical diagnosis of diseases due to its advantages: high definition and noninvasive. Therefore, computer-aided diagnosis based on sMRI images is broadly applied in classifying Alzheimer’s disease (AD). Due to the excellent performance of Transformer in computer vision, Vision Transformer (ViT) has been employed for AD classification in recent years. ViT relies on access to large datasets, while the sample size of brain imaging datasets is relatively insufficient. Moreover, the pre-processing procedures of brain sMRI images are complex and labor-intensive. To overcome the limitations mentioned above, we propose Resizer Swin Transformer (RST), a deep learning model that can extract information from brain sMRI images that are only briefly processed to achieve multi-scale and cross-channel features. In addition, we pre-trained our RST on a natural image dataset and obtained better performance. The experimental results of ADNI and AIBL datasets prove that RST can achieve better classification performance in AD prediction compared with CNN-based and Transformer models.

The challenging issues of Computer Network and Databases are not only the intrusion detection but also the reduction of false positive and increase of detection rate. In any intrusion detection system, anomaly detection mainly focuses on modeling the normal behavior of the users and detecting the deviations from normal behavior which are assumed to be potential intrusions or treat. Several techniques have already been successfully tried for this purpose. However, the normal and suspicious behavior are hard to predict as there is no precise boundary differentiat-ing one from another. Here rough set theory and fuzzy set theory come into the picture. In this article, a hybrid approach based on rough set theory and intuitionistic fuzzy set theory is pro-posed for the detection of anomaly. The proposed approach is a classification approach which takes the advantages of softness properties both rough and fuzzy set theory to deal with uncer-tainty in the dataset. The algorithm classifies the data instances in such a way that they can be expressed using natural language. The experimental results with a real world dataset and a syn-thetic dataset show that the proposed algorithm has normal true positive rates of 91.989% and 96.99% and attack true positive rates of 91.289% and 96.29% respectively

Along with the popularity of the Internet, people are exposed to more and more ways of micro-videos, and a huge amount of micro-video data has emerged. micro-videos have gradually become the Internet content preferred by the public, and a large number of micro-video apps have also emerged, such as Tiktok and Kwai. Intelligent classification and mining of micro-videos can greatly enhance user experience, improve business operation efficiency and enhance user experience. Through deep intelligent analysis and mining of micro-videos, important information in micro-videos can be extracted to provide an important basis for beautifying videos, content appreciation, video recommendation, content search, etc. In the past, content understanding for short videos often used human work annotation, but in recent years, with the great success of deep convolutional neural networks in image recognition, short video content understanding based on this method has gradually developed. Nowadays, most recognition algorithms extract the feature representation of each frame independently and then fuse them. However, while extracting the feature representation, some low-level semantic features are lost, which makes the algorithm unable to accurately distinguish the category of the video. At present, the algorithm of micro-video recognition based on deep learning has surpassed the iDT algorithm, making these traditional methods fade out of people’s view. In this paper according to the micro-video classification task, a new network model is proposed to concatenate features of each modality into the overall features of various modalities through the network, and then fuse the various modal features with the attention mechanism to obtain the whole micro-video features, which will be used for classification. In order to verify the effectiveness of the algorithm proposed in this paper, experiments are conducted in the public dataset, and it is shown the effectiveness of our model.

Ransomware is one of the most dangerous types of malware, which is frequently intended to spread through a network to damage the designated client by encrypting the client’s vulnerable data. Conventional signature-based ransomware detection technique falls behind because it can only detect known anomalies. When it comes to new and non-familiar ransomware traditional system unveils huge shortcomings. For detecting unknown patterns and sorts of new ransomware families,behavior-based anomaly detection approaches are likely to be the most efficient approach. In the wake of this alarming condition, this paper presents an ensemble classification model consisting of three widely used machine learning techniques that include Decision Tree (DT), RandomForest (RF), and K-nearest neighbor (KNN). To achieve the best outcome ensemble soft voting and hard voting techniques are used while classifying ransomware families based on attack attributes. Performance analysis is done by comparing our proposed ensemble models with standalone models on behavioral attributes based ransomware dataset..

Intelligent systems are transforming the world, as well as our healthcare system. We propose a deep learning-based cough sound classification model that can distinguish between children with healthy versus pathological coughs such as asthma, upper respiratory tract infection (URTI), and lower respiratory tract infection (LRTI). In order to train a deep neural network model, we collected a new dataset of cough sounds, labelled with clinician's diagnosis. The chosen model is a bidirectional long-short term memory network (BiLSTM) based on Mel Frequency Cepstral Coefficients (MFCCs) features. The resulting trained model when trained for classifying two classes of coughs -- healthy or pathology (in general or belonging to a specific respiratory pathology), reaches accuracy exceeding 84\% when classifying cough to the label provided by the physicians' diagnosis. In order to classify subject's respiratory pathology condition, results of multiple cough epochs per subject were combined. The resulting prediction accuracy exceeds 91\% for all three respiratory pathologies. However, when the model is trained to classify and discriminate among the four classes of coughs, overall accuracy dropped: one class of pathological coughs are often misclassified as other. However, if one consider the healthy cough classified as healthy and pathological cough classified to have some kind of pathologies, then the overall accuracy of four class model is above 84\%. A longitudinal study of MFCC feature space when comparing pathologicial and recovered coughs collected from the same subjects revealed the fact that pathological cough irrespective of the underlying conditions occupy the same feature space making it harder to differentiate only using MFCC features.

This paper discusses the computer-aided (CAD) classification between Hepatocellular Carcinoma (HCC), i.e., the most common type of liver cancer, and Liver Abscess, based on ultrasound image texture features and Support Vector Machine (SVM) classifier. Among 79 cases of liver diseases, with 44 cases of HCC and 35 cases of liver abscess, this research extracts 96 features of Gray-Level Co-occurrence Matrix (GLCM) and Gray-Level Run-Length Matrix (GLRLM) from the region of interests (ROIs) in ultrasound images. Three feature selection models, i) Sequential Forward Selection, ii) Sequential Backward Selection, and iii) F-score, are adopted to determine the identification of these liver diseases. Finally, the developed system can classify HCC and liver abscess by SVM with the accuracy of 88.875%. The proposed methods can provide diagnostic assistance while distinguishing two kinds of liver diseases by using a CAD system.

Singing melody extraction is the task that identifies the melody pitch contour of singing voice from polyphonic music. Most of the traditional melody extraction algorithms are based on calculating salient pitch candidates or separating the melody source from the mixture. Recently, classification-based approach based on deep learning has drawn much attentions. In this paper, we present a classification-based singing melody extraction model using deep convolutional neural networks. The proposed model consists of a singing pitch extractor (SPE) and a singing voice activity detector (SVAD). The SPE is trained to predict a high-resolution pitch label of singing voice from a short segment of spectrogram. This allows the model to predict highly continuous curves. The melody contour is smoothed further by post-processing the output of the melody extractor. The SVAD is trained to determine if a long segment of mel-spectrogram contains a singing voice. This often produces voice false alarm errors around the boundary of singing segments. We reduced them by exploiting the output of the SPE. Finally, we evaluate the proposed melody extraction model on several public datasets. The results show that the proposed model is comparable to state-of-the-art algorithms.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

The objectives of this paper are to analyze the urban growth and urbanization phenomenon in Algeria. Two processes that originated respectively by the expansion of existing urban areas and the process of urbanization that took place between 1954 and 2008, a period marked by significant economic, social and political changes in Algerian society. Our analysis was mainly based on the Algerian general census of population and habitat (2008) and on the application of rank-size distribution of cities according to Zipf’s rule. This study revealed that in Algeria, the urban system is particularly marked by the dramatic expansion of small cities. Indeed, the development of small towns, through the transition from rural to urban and the residential loosening of large cities have influenced the trend towards the balance of the urban system in Algeria. Results revealed also how the "primatial" city is undergoing profound economic and social changes at the national level. These changes are most often imposed from the top as part of land-use planning policy. This study provides some insights into the demographic dynamics of cities and the evolution of urban hierarchies in Algeria, through the comparison of the different rank-size distributions of Algerian cities in space and time. Our results suggest that land-use planning strategies are the only policies capable of influencing the future of the Algerian urban system.

Analyzing horse behavior is crucial for assessing training quality, particularly in accurately identifying actions like standing, walking, and running. Research has been conducted both domestically and internationally in this regard; however, challenges persist, including reliance on single sensors, poor real-time performance, and low identification accuracy. In view of these challenges, this study investigated real-time identification of horse behavior based on wearable devices. The system, centered around a microcontroller and utilizing a 4G network as a carrier, employs multi-axis IMU sensors as input sources to perceive horse posture. The study proposed a behavior classification method based on analysis of acceleration thresholds. The method consists primarily of two sequential stages: first, the resultant acceleration interval counting method, which employs a nonlinear segmentation approach for initial behavior classification; and second, the statistical analysis of variance parameters between segments, which when coupled with multi-level threshold processing, achieves a refined classification. Experimental results indicated that the interval counting method alone achieved an accuracy of 87.55%, while for the variance analysis method alone the accuracy was 90.87%. The proposed method, comprising the two stages, reached a classification accuracy of 91.57%, underpinning its usefulness in supporting future equine research.

Aiming at the classification identification problem of aeroengines, this paper adopts telemetry Fourier Transform Infrared Spectrometer to collect aeroengine hot jet infrared spectrum data, and proposes an aeroengine classification identification method based on spectral feature vectors. First, aeroengine hot jet infrared spectrum data are acquired and measured, meanwhile, the spectral feature vectors based on CO2 are constructed. Then, the feature vectors are combined with the seven mainstream classification algorithms to complete the training and prediction of the classification model. In the experiment, two Fourier transform infrared spectrometers, EM27 developed by Bruker and a self-developed telemetry FTIR, were used to telemeter the hot jet of three aeroengines to obtain infrared spectral data. The training data set and test data set were randomly divided in a ratio of 3:1. The model training of the training data set and the label prediction of the test data set were carried out by combining spectral feature vectors and classification algorithms. The classification evaluation indicators were accuracy, precision, recall, confusion matrix, and F1-score. The classification recognition accuracy of the algorithm was approximately 98%. This paper has great significance for the fault diagnosis of aeroengines and classification recognition of aircrafts.

In this paper, we propose a partial differential equation model based on phase-field for sentiment analysis in the field of hotel comment texts. The comment texts are converted into word vectors using the Word2Vec tool, and then we utilize the multifractal detrended fluctuation analysis (MF-DFA) model to extract the generalized Hurst exponent of the word vector time series to achieve dimensionality reduction of the word vector data. The dimensionality reduced data is represented in a two-dimensional computational domain, and the modified Allen-Cahn (AC) function is used to evolve the phase values of the data to obtain a stable nonlinear boundary, thereby achieving automatic classification of hotel comment texts. The experimental results show that the proposed method can effectively classify positive and negative samples and achieve excellent results in classification indicators. We compared our proposed classifier with traditional machine learning models and the results indicate that our method possesses a better performance.

This research assesses the classification of Arabic coffee into three primary variations (light, medium, and dark) using simulated data based on actual measurements of color information, antioxidant laboratory tests, and chemical composition tests. Two types of simulated data were generated, with the standard deviation of the measures varied. Multiple classifiers were used for classification. The findings demonstrate the use of color information in accurately distinguishing Arabic coffee types. The different CIE color values, as well as the excellent connection between color information and coffee classes, lead to flawless classification results. However, depending primarily on antioxidant information results in lower classification performance, with variability amongst classifiers due to increasing data complexity. Chemical composition information, on the other hand, possesses outstanding discriminatory strength, allowing faultless classification on its own. Certain characteristics, such as crude protein and crude fiber, show strong correlations and are critical in the classification of coffee types. Based on the findings, it is recommended to create a mobile application that uses image recognition to analyze coffee color while providing chemical composition information. End users, such as consumers, will be able to make informed judgments regarding their coffee preferences owing to this application.

To drive safely, the driver must be aware of the surroundings, pay attention to the road traffic, and be ready to adapt to new circumstances. Most studies on driving safety focus on detecting anomalies in driver behavior and monitoring the cognitive capabilities of drivers. In our study, we proposed a classifier for basic activities in driving a car, based on a similar approach that could be applied to the recognition of basic activities in daily life, that is, using electrooculographic (EOG) signals and a one-dimensional convolutional neural network (1D CNN). Our classifier achieved an accuracy of 80% for the 16 primary and secondary activities. The accuracy related to primary activities in driving, including crossroad, parking, roundabout was 97.9%, 96.8%, 97.4%, and 99.5%, respectively. The F1 score for secondary driving actions (0.99) was higher than for primary driving activities (0.93–0.94). Furthermore, using the same algorithm, it was possible to distinguish four secondary activities related to activities of daily life and secondary when driving a car.

Spike-and-wave discharge (SWD) pattern detection in electroencephalography (EEG) signals is a key signal processing problem. It is particularly important for overcoming time-consuming, difficult, and error-prone manual analysis of long-term EEG recordings. This paper presents a new SWD method with a low computational complexity that can be easily trained with data from standard medical protocols. Precisely, EEG signals are divided into time segments for which the Morlet 1-D decomposition is applied. The generalized Gaussian distribution (GGD) statistical model is fitted to the resulting wavelet coefficients. A k-nearest neighbors (k-NN) self-supervised classifier is trained using the GGD parameters to detect the spike-and-wave pattern. Experiments were conducted using 106 spike-and-wave signals and 106 non-spike-and-wave signals for training and another 96 annotated EEG segments from six human subjects for testing. The proposed SWD classification methodology achieved 95 % sensitivity (True positive rate), 87% specificity (True Negative Rate), and 92% accuracy. These results set the path to new research to study causes underlying the so-called absence epilepsy in long-term EEG recordings.

Group-IV GeSn photodetectors (PDs) compatible with standard complementary metal-oxide-semiconductor (CMOS) processing have emerged as a new and non-toxic infrared detection technology to enable a wide range of infrared applications. The performance of GeSn PDs is highly dependent on the Sn composition and operation temperature. Here, we develop theoretical models to establish a simple rule of thumb, namely “GeSn-rule 23”, to describe GeSn PDs’ dark current density in terms of operation temperature, cutoff wavelength, and Sn composition. In addition, analysis of GeSn PDs’ performance shows that the responsivity, detectivity, and bandwidth are highly dependent on operation temperature. This rule provides a simple and convenient indicator for device developers to estimate the device performance at various conditions for practical applications.

Malignant mesothelioma is a rare proliferative cancer that develops in the thin layer of tissues surrounding the lungs. Malignant mesothelioma is associated with an extremely poor prognosis and the majority of patients do not show symptoms. The epidemiology of mesothelioma is important for the identification of disease. The primary aim of this study is to explore the risk factors associated with mesothelioma. The dataset consists of healthy and mesothelioma patients but only mesothelioma patients were selected for the identification of symptoms. The raw data set has been pre-processed and then the Apriori method was utilized for association rules with various configurations. The pre-processing task involved the removal of duplicated and irrelevant attributes, balanced the dataset, numerical to the nominal conversion of attributes in the dataset and creating the association rules in the dataset. Strong associations of disease’s factors; asbestos exposure, duration of asbestos exposure, duration of symptoms, erythrocyte sedimentation rate and Pleural to serum LDH ratio determined via Apriori algorithm. The identification of risk factors associated with mesothelioma may prevent patients from going into the high danger of the disease. This will also help to control the comorbidities associated with mesothelioma which are cardiovascular diseases, cancer-related emotional distress, diabetes, anemia, and hypothyroidism.

This paper presents a novel approach to sentiment analysis specifically customized for predicting stock market movements, bypassing the need for external dictionaries which are often unavailable for many languages. Our methodology directly analyzes textual data, with a particular focus on context-specific sentiment words within neural network models. This specificity ensures our sentiment analysis is both relevant and accurate in identifying trends in the stock market. We employ sophisticated mathematical modeling techniques to enhance both the precision and interpretability of our models. Through meticulous data handling and advanced machine learning methods, we leverage large datasets from Twitter and financial markets to examine the impact of social media sentiment on financial trends. We achieved an accuracy exceeding 75%, highlighting the effectiveness of our modeling approach, which we further refined into a convolutional neural network model. This achievement contributes valuable insights into sentiment analysis within the financial domain, thereby improving the overall clarity of forecasting in this field.

The incessant evolution of online platforms has ushered in a multitude of shopping modalities. Within the food industry, however, assessing the delectability of meals can only be tentatively determined based on consumer feedback encompassing aspects such as taste, pricing, packaging, service quality, delivery timeliness, hygiene standards, and environmental considerations. Traditional text data mining techniques primarily focus on consumers' emotional traits, disregarding pertinent information pertaining to the online products themselves. In light of these aforementioned issues in current research methodologies, this paper introduces the Bert BiGRU Softmax model combined with multimodal features to enhance the efficacy of sentiment classification in data analysis. Comparative experiments conducted using existing data demonstrate that the accuracy rate of the model employed in this study reaches 90.9%. In comparison to single models or combinations of three models with the highest accuracy rate of 7.7%, the proposed model exhibits superior accuracy and proves highly applicable to online reviews.

Augmented reality (AR) provides an opportunity for mobile fitness applications to show users real-time feedback on their current fitness activity. For such applications, it is essential to accurately track the user’s current fitness activity using available mobile sensors, such as inertial measurement units (IMUs). Convolutional neural networks (CNNs) have been shown to produce strong results in different time series classification tasks, including the recognition of activities of daily living. However, fitness activities can present unique challenges to the human activity recognition task (HAR), including greater similarity between individual activities and fewer available data for model training. In this paper, we evaluate the applicability of CNNs to the fitness activity recognition task (FAR) using IMU data and determine the impact of input data size and sensor count on performance. For this purpose, we adapted three existing CNN architectures to the FAR task and designed a fourth CNN variant, which we call the scaling fully convolutional network (Scaling-FCN). We designed a preprocessing pipeline and recorded a running exercise data set with 20 participants, in which we evaluated the respective recognition performances of the four networks, comparing them with three traditional machine learning methods commonly used in HAR. On our data set, all CNN architectures significantly outperformed traditional machine learning methods, reaching up to 97.14±1.36% classification accuracy on the test set for ResNet. Whereas a reduced input data size invariably led to a performance loss, removing specific sensors improved the performance of all CNN architectures, with our Scaling-FCN reaching the highest accuracy of 99.86±0.11%. Our results suggest that CNNs are generally well suited for fitness activity recognition, and noticeable performance improvements can be achieved if sensors are dropped selectively.

To solve the problem that the common long-tailed classification method does not use the semantic features of the original label text of the image, and the difference between the classification accuracy of most classes and minority classes is large, the long-tailed image classification method based on enhanced contrast visual language trains the head class and tail class samples separately, uses text image to pre-train the information, and uses enhanced momentum contrast loss function and RandAugment enhancement to improve the learning of tail class samples. On the ImageNet-LT long-tailed dataset, the enhanced contrastive visual-language based long-tailed image classification method has improved all class accuracy, tail class accuracy, middle class accuracy, and F1 values by 3.4%, 7.6%, 3.5%, and 11.2%, respectively, compared to the BALLAD method. The difference in accuracy between the head class and tail class is reduced by 1.6% compared to the BALLAD method. The results of three comparative experiments indicate that the long-tailed image classification method based on enhanced contrastive visual-language has improved the performance of tail classes and reduced the accuracy difference between majority and minority classes.

3D point cloud classification tasks have been a hot topic in recent years. Most existing point cloud processing frameworks lack context-aware features due to the deficiency of sufficient local feature extraction information. Therefore, we design an augmented sampling and grouping (ASG) module to efficiently obtain fine-grained features from the original point cloud. In particular, this method strengthens the domain near each centroid and makes reasonable use of the local mean and global standard deviation to mine point cloud’s local and global features. In addition to this, inspired by the transformer structure UFO-ViT in 2D vision tasks, we first try to use a linearly-normalized attention mechanism in point cloud processing tasks, investigating a novel transformer-based point cloud classification architecture UFO-Net. An effective local feature learning module is adopted as a bridging technique to connect different feature extraction modules. Importantly, UFO-Net employs multiple stacked blocks to better capture feature representation of the point cloud. Extensive ablation experiments on public datasets show that our method outperforms other state-of-the-art methods. For instance, our network performed with 93.7% overall accuracy on the ModelNet40 dataset, which was 0.5% higher than PCT. Our network also archived 83.8% overall accuracy on the ScanObjectNN dataset, which is 3.8% better than PCT.

Ubiquitous computing comprises scenarios where networks, devices within the network, and software components change frequently. Market demand and cost-effectiveness are forcing device manufacturers to introduce new-age devices. Also, the Internet of Things (IoT) is transitioning rapidly from the IoT to the Internet of Everything (IoE). Due to this enormous scale, effective management of these devices becomes vital to support trustworthy and high-quality applications. One of the key challenges of IoT device management is automatic device classification with the logically semantic type and using that as a parameter for device context management. This would enable smart security solutions. In this paper, a device classification approach is proposed for the context management of ubiquitous devices based on unsupervised machine learning. To classify unknown devices and to label them logically, a proactive device classification model is framed using a k-Means clustering algorithm. To group devices, it uses the information of network parameters such as Received Signal Strength Indicator (rssi), packet_size, number_of_nodes in the network, throughput, etc. Experimental analysis suggests that the well-formedness of clusters can be used to derive cluster labels as a logically semantic device type which would be a context for resource management and authorization of resources. This paper fulfills an identified need of proactive device classification for device management.

Speech/music classification that facilitates optimized signal processing from classification results has been extensively adapted as an essential part of various electronics applications, such as multi-rate audio codecs, automatic speech recognition, and multimedia document indexing. In this paper, a new technique to improve the robustness of speech/music classifier for 3GPP enhanced voice service (EVS) using long short-term memory (LSTM) is proposed. For effective speech/music classification, feature vectors implemented with the LSTM are chosen from the features of the EVS. Experiments show that LSTM-based speech/music classification produces better results than conventional EVS under a variety of conditions and types of speech/music data.

The advent of deep learning (DL) has revolutionized medical imaging, offering unprecedented avenues for accurate disease classification and diagnosis. DL models have shown remarkable promise for classifying brain tumor from Magnetic Resonance Imaging (MRI) scans. However, despite their impressive performance, the opaque nature of DL models poses challenges in understanding their decision-making processes, particularly crucial in medical contexts where interpretability is essential. This paper explores the intersection of medical image analysis and DL interpretability, aiming to elucidate the decision-making rationale of DL models in brain tumor classification. Leveraging state-of-the-art DL frameworks with transfer learning, we conduct a comprehensive evaluation encompassing both classification accuracy and interpretability. Using state-of-the-art DL frameworks with transfer learning, we conduct a thorough evaluation covering both classification accuracy and interpretability. We employ adaptive path-based techniques to understand the underlying decision-making mechanisms of these models. Grad-CAM and Grad-CAM++ highlight critical image regions where the tumors are located.

In Indonesia, types of meat are still identified manually due to increasing prices for beef and buf-falo ahead of Idul Fitri. Traders mix beef with pork to thwart the beef scam. Haar wavelet and GLCM, GLCM with angles of 0°, 45°, 90°, and 135°, as well as matrices using contrast, correlation, energy, homogeneity, and entropy, are used in feature extraction. The following are the results of meat image classification testing using k-NN, Haar wavelet, and GLCM: The k-NN algorithm shows superiority in identifying fresh (99%), frozen (99%), and rotten (96%) meat texture images with the most fantastic accuracy results in every situation. Meanwhile, GLCM routinely provides good results, especially regarding the texture image of fresh meat (183.21) and rotten meat (115.79). However, despite delivering less throughput than k-NN and GLCM, Haar wavelets are still helpful, especially when dealing with fresh meat texture images (89,96).

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Deep Learning (DL) oriented document processing is widely used in different fields for extraction, recognition, and classification processes from raw corpora of data. The article examines the application of deep learning approaches, based on different neural network methods, including Gated Recurrent Unit (GRU), Long Short-Term Memory (LSTM), and Convolutional Neural Networks (CNN). The compared models were combined with two different word embedding techniques, namely: Bidirectional Encoder Representations from Transformers BERT and Gensim Word2Vec. The models are designed to evaluate the performance of architectures based on neural network techniques for the classification of CVs of Moroccan engineering students at ENSAK(National School of Applied Sciences of Kenitra, Ibn Tofail University). The used dataset included resumes collected from engineering students at ENSAK in 2023 for a project on the employability of Moroccan engineers in which new approaches were applied, especially machine learning, deep learning, and big data. Accordingly, 867 resumes were collected from five specialties of study (Electrical Engineering, Networks and Systems Telecommunications, Computer Engineering, Automotive Mechatronics Engineering, Industrial Engineering). The results revealed good performance of the proposed models based on the BERT embedding approach compared to models based on the Gensim Word2Vec embedding approach. Accordingly, the CNN-GRU/Bert model achieved slightly better accuracy with 0.9251 compared to other hybrid models.

The large quantity of information retrieved from communities, public data repositories, web pages, or data mining can be sparsed and poorly classified. This work shows how to employ unsupervised classification algorithms such as K-means proper to classify user reviews into their closest category, forming a balanced data set. Moreover, we found that the text vectorization technique significantly impacts the clustering formation, comparing TF-IDF and Word2Vec. The value for mapping a cluster with movie genre was 81.34% ± 20.48 of the cases when the TF-IDF was applied, whereas Word2Vec only yielded a 53.51% ± 24.1. In addition, we highlight the impact of the removal of stop-words. Thus, we detected that pre-compiled lists are not the best method to remove stop-words before clustering because there is much ambiguity, centroids are poorly separated, and only 57% of clusters could match a movie genre. Thus, our proposed approach achieved a 94% of accuracy. After analyzing the classifiers’ results, we appreciated a similar effect when divided by the stop-words method removal. Statistically significant changes were observed, especially in precision metric and Jaccard scores in both classifiers, using custom-generated stop lists rather than pre-compiled ones. Reclassifying sparse data is strongly recommended as using custom-generated stop lists.

This work addresses the challenge of EEG visual multiclass classification into 40 classes for Brain-Computer interface applications, by using deep learning architectures. The visual multiclass classification approach offers BCI applications a significant advantage, since it allows the supervision of more than one BCI interaction, considering that each class label supervises a BCI task. However, because of the nonlinearity and nonstationarity of EEG signals, performing multiclassifiers based on EEG features remains a significant challenge for BCI systems. In the present work, mutual information-based discriminant channel selection and Minimum-Norm Estimate algorithms are implemented to select discriminant channels and enhance EEG data. Hence, deep EEGNet and Convolutional-recurrent neural networks are implemented separately to classify EEG data of image visualization into 40 labels. By using the k-fold cross-validation approach, average classification accuracies of 94.8% and 89.8% were obtained by implementing the aforementioned network architectures, respectively. Satisfactory results obtained with this method offer a new implementation opportunity for multi-task BCI applications by utilizing a reduced number of channels (<50%), compared to those presented in the related literature where the whole set of channels is used.

Agriculture is one of the indispensable fields for the survival of mankind. Potatoes also have a significant role in the field of agriculture. The quality and quantity of potatoes are significantly impacted by several diseases, such as early blight and late blight, and manual interpretation of these leaf diseases is time-consuming and inconvenient. Fortunately, leaf appearance is used to detect diseases in potato plants. Productivity will considerably rise if the infections are detected early. Different types of image processing methods and machine learning methods are used for early recognition of those diseases from leaf images so that the product losses are decreased significantly. For the incredible and marvelous performance of CNN, it is the most popular deep learning method that is used immensely for the recognition of leaf diseases from images. Several pretrained deep learning models, such as VGG16, ResNet50, InceptionV3, MobileNetV2, Xception, and a deep learning model developed using CNN, are employed for potato leaf disease classification and recognition on the same dataset. The transfer learning technique is applied to the pretrained model and the data augmentation technique is applied to the Proposed CNN model for potato disease classification from leaf samples. Compared to pretrained models, the proposed CNN model offers the lowest loss and highest accuracy for potato leaf disease detection while using fewer parameters and layers. It achieves the best performance with a test accuracy of 99.33% compared to other Pretrained models used in the diagnosis of potato leaf disease.

It is important for food recognition to separate each ingredient within a food image at the pixel level. In this paper, we propose a new approach to segment ingredients by utilizing a CNN-based Single-Ingredient Classification Model. In detail, we firstly introduce a standardized biological-based hierarchical ingredient structure and construct a single-ingredient image dataset based on this structure. Then, we build a single-ingredient classification model based on a novel convolutional neural network (CNN) architecture that utilizes an attention mechanism. Afterwards, we propose a new framework for segmentation using the above single-ingredient classification model as the backbone. In this framework, two methods are involved in segmenting ingredients in the food images. We introduce five evaluation metrics (IoU, Dice, Purity, Entirety, Loss of GTs) to assess the performance of ingredient segmentation in terms of ingredient classification. Extensive experiments demonstrate the effectiveness of the proposed method, achieving an maximal mIoU of 0.65, mDice of 0.77, mPurity of 0.83, mEntirety of 0.80, and mLoGTs of 0.06 on the FoodSeg103 dataset. The results confirm that our CNN-based architecture achieves higher segmentation performance compared to ResNet18 and EfficientNet-B0 when used as the backbone for ingredient segmentation. We believe that our ingredient segmentation approach lays the foundation for subsequent ingredient recognition.

Influential Observations, which are outliers in x direction, y direction or both, remain a hitch in classical regression model fitting. Spatial regression model, with peculiar nature of outliers due to their local nature, is not free from the effect of such influential observations. Researchers have adapted some classical regression techniques to the spatial models and yielded satisfactory results. However, masking or/and swamping remain stumbling block to such methods. We obtained the spatial representation of the classical regression measures of diagnostic in general spatial model. Commonly used diagnostic measure in spatial diagnostic, the Cook's distance, is compared to some robust methods, Hi2 (using robust and non-robust measures), and classification based on generalized residuals and diagnostic generalized potentials, ISRs-Posi and ESRs-Posi, with the help of the obtained spatial prediction residuals and the spatial leverage term. Results of simulation and applications to real data have shown the advantage of the ISRs-Posi and ESRs-Posi due to classification of outliers over Cook's distance and non-robust Hsi12, which suffer from masking, and robust Hsi22 which suffer from swamping in general spatial model.

Remediation of IT issues encoded into domain-specific or user-defined alerts occurring in cloud environments and customer ecosystems in a vast majority of cases suffers from accurate recommendations which could be timely supplied for recovery of performance degradations. That, of course, is hard to realize through furnishing those abnormality definitions with an appropriate expert knowledge which varies from one environment to another. At the same time, in a large proportion of support cases, the reported problems under Global Support Services (GSS) or Site Reliability Engineering (SRE) treatment ultimately go down to the product teams making them waste costly development hours on investigating self-monitoring metrics of our solutions. Therefore, the mean-time-to-resolution (MTTR) rates of problems/alerts are significantly impacted from lack of a systematic approach towards adopting AI Ops. That would imply building, maintaining, and continuously improving/annotating a data store of insights that ML models are trained and generalized across the whole customer base and corporate cloud services. Our ongoing study is in line with such a vision and validates an approach that learns the alert resolution patterns in such a global setting and explains them using interpretable AI methodologies. The knowledge store of causative rules is then applied in predicting potential sources of the application degradation reflected in an active alert instance. In this communication, we share our experiences with a prototype solution and up to date analysis demonstrating how root conditions are discovered with a high accuracy for a specific type of problem. It is validated against the historical data of resolutions performed by heavy manual development efforts. We also offer a Dempster-Shafer theory-based rule verification framework for experts as a what-if analysis tool to test their hypotheses about underlying environment.

Accurate crop diseases classification is crucial for ensuring food security and enhancing agricultural productivity. However, existing crop disease classification algorithms primarily focus on a single image modality and typically require a large number of samples. Our research counters these issues by using pre-trained Vision-Language Models (VLMs), which enhances multimodal synergy for better crop disease classification than traditional unimodal approaches. Firstly, we apply the multimodal model Qwen-VL to generate meticulous textual descriptions for representative disease images selected through clustering from the training set, which will serve as prompt text for generating classifier weights. Compared to using solely the language model for prompt text generation, this approach better captures and conveys fine-grained and image-specific information, thereby enhancing prompt quality. Secondly, we integrate the cross-attention and the SE (Squeeze-and-Excitation) attention into the training-free mode VLCD (Vision-Language model for Crop Diseases classification) and the training-required mode VLCD-T (VLCD-Training) respectively for prompt text processing, enhancing classifier weights by emphasizing key text features. Experimental outcomes conclusively prove our method’s heightened classification effectiveness in few-shot crop disease scenarios, tackling data limitations and intricate disease recognition issues. It offers a pragmatic tool for agricultural pathology and reinforces the smart farming surveillance infrastructure.

Polarimetric features extracted from polarimetric synthetic aperture radar (PolSAR) images contain abundant scattering information of objects. Utilizing this information for PolSAR image classification can improve accuracy and enhance object monitoring. Although significant progress has been achieved in related research, there are still issues such as insufficient utilization of polarimetric information and features. In this paper, a deep learning classification method based on polarimetric channel power features for PolSAR is proposed. The distinctive characteristic of this method is that the polarimetric features inputted into the deep learning network are the power values of polarimetric channels, where these channels are treated equivalently and contain complete polarimetric information. In terms of experimental comparative study, besides polarimetric power combinations, three different data input schemes were employed as data for the input end of the convolutional neural network (CNN), taking into account existing research. The neural networks utilizes the extracted polarimetric features to classify images, and the classification accuracy analysis is employed to compare the strengths and weaknesses of different input schemes. It is worth mentioning that the polarized characteristics of the data input scheme mentioned in this article have been derived through rigorous mathematical deduction, and each polarimetric feature has clear physical meaning. By testing different data input schemes on the Gaofen-3 (GF-3) PolSAR image, the experimental results show that the method proposed in this article outperforms existing methods and can improve the accuracy of classification to a certain extent, validating the effectiveness of this method in large-scale area classification.

Leveraging the open-world understanding capacity of large-scale visual-language pre-trained models has become a hot-spot in point cloud classification. Recent approaches rely on transferable visual-language pre-trained models, classifying point clouds by projecting them into 2D images and evaluating consistency with textual prompts. These methods benefit from the robust open-world understanding capabilities of visual-language pre-trained models and require no additional training. However, they face several challenges summarized as prompt ambiguity, image domain gap, view weights confusion, and feature deviation. In response to these challenges, we propose PointBLIP, a zero-training point cloud classification network based on the recently introduced BLIP-2 visual-language model. PointBLIP is adept at processing similarities between multi-images and multi-prompts. We separately introduce a novel method for point cloud zero-shot and few-shot classification, which involves comparing multiple features to achieve effective classification. Simultaneously, we enhance the input data quality for both the image and text sides of PointBLIP. In point cloud zero-shot classification tasks, we outperform state-of-the-art methods on three benchmark datasets. For few-shot classification tasks, to the best of our knowledge, we present the first zero-training few-shot point cloud method, surpassing previous works under the same conditions and showcasing comparable performance to full-training methods.

Biosynthetic gene clusters are specific genomic regions in microorganisms, like bacteria and fungi, responsible for producing bioactive compounds. Identifying these clusters is complex due to their diverse nature. This research presents a comprehensive approach to effective BGC identification. The study focuses on five classes of Natural Products: PKS , NRPS, RiPP, Terpenes, and Hybrid PKS-NRPS. Data was gathered from the MiBIG database in GBK format. Protein sequences from each file were extracted, and sequences under the same BGC ID were combined. Physicochemical properties were calculated, and sequence embeddings were generated using NLP techniques like CountVec, TFIDF, and Word2Vec specific to each NP class. An integrated feature matrix was created by merging physicochemical properties and generated embeddings. This matrix was used for training and testing of nine ML models such SVM, RF and many more. The study explored data balancing techniques with and without SMOTE and employed Grid Search for parameter optimization. This led to six datasets and 54 models. The LR model, using TFIDF with SMOTE, emerged as the most effective, achieving an accuracy of 0.96, AUC of 0.9912, and other strong metrics. This method enhances BGC identification for drug development, offering a broader understanding of their applications in medicine and biotechnology.

The task of unsupervised anomalous sound detection (ASD) is challenging for detecting anomalous sounds from a large audio database without any annotated anomalous training data. Many unsupervised methods were proposed, but previous works have confirmed that the classification-based models far exceeds the unsupervised models in ASD. In this paper, we adopt two classification-based anomaly detection models: (1) Outlier classifier is to distinguish anomalous sounds or outliers from the normal; (2) ID classifier identifies anomalies using both the confidence of classification and the similarity of hidden embeddings. We conduct experiments in task 2 of DCASE 2020 challenge, and our ensemble method achieves an averaged area under the curve (AUC) of 95.82% and averaged partial AUC (pAUC) of 92.32%, which outperforms the state-of-the-art models.