Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Climate and land use changes are major factors affecting runoff in regional basins. Understanding variation by considering interactions among hydrological components is an important process for water resource management. This study aimed to assess the variation of future runoff in the Upper Chi Basin, Northeastern Thailand. QSWAT hydrological model was integrated to 3 CMIP6 GCMs including ACCESS-CM2, MIROC6, and MPI-ESM1-2-LR under SSP245 and SSP585 scenarios during 2023 – 2100. Land Change Modeler (LCM) was also used for future land use simulation. The results revealed that future average of long-term precipitation and temperature tended to increase while forest land tended to decrease and be replaced by sugarcane plantations. The accuracy assessment of baseline year runoff calculation by QSWAT during 1997 – 2022 showed acceptable result as can be seen from R2, NSE, RSR, and PBIAS indices. This result could lead to temporal and spatial simulation of future runoff. Likewise, runoff of 2 SSPs scenarios tended to increase consecutively, especially in SSP585 scenario. In addition, in case of long-term spatial changes in the subbasins scale, over 90% of the area, from upstream to outlet point, tended to get higher due to 2 major factors including future increased precipitation and changes in cultivation, which would be influential to groundwater and interflow components respectively. Methodology and result of this study can be useful to stakeholders in understanding changes in hydrological system so that they can apply it to develop a strategy for water resource management and handling factors affecting different dimensions properly and sustainably.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

Digital Elevation Models (DEMs) are essential in watershed delineation, but the sensitivity of simulated runoff to DEM resolution is poorly understood. This study investigates the impact of DEM resolution on topological attributes and simulated runoff in the Mahabad Dam watershed, Iran. To delineate the watershed, DEMs with 12.5 m, 30 m, and 90 m resolutions were acquired from the ALOS PALSAR, Space Shuttle Radar Topography Mission (SRTM), and ASTER global DEM data source, respectively. Watershed and streamlines were delineated in ArcGIS, with hydrologic analyses performed using the Soil and Water Assessment Tool (SWAT). Sensitivity analysis on parameters contributing to runoff was done using Sequential Uncertainties Fitting Ver-2 (SUFI-2) Algorithm, in SWAT Calibration and Uncertainty Procedures (SWAT-CUP) software. Results showed the watershed area, reach lengths, and elevations in the watershed varied due to DEM resolutions. Higher amounts of runoff were generated when DEMs with finer resolutions were implemented. The 12.5 m DEM generated 3.48% and 0.42% more runoff compared with 90 m and 30 m DEMs, respectively. SWAT-CUP results showed the sensitivity of parameters contributing to runoff changes under different DEM resolutions. Regardless of DEM resolution, surface properties, available water capacity, and moisture levels in the soil are the most sensitive parameters. As the distribution of slope changes in different DEM resolutions, surface parameters are most affected. The findings indicate to reduce computation time and speed up computation procedures, researchers may use DEMs with coarser resolutions at the expense of minor decreases in accuracy.

Clinical and laboratory diagnostics are particularly important in monitoring the internal homeostasis of the body in high-yielding animals, especially in dairy cows, whose metabolism is under constant pressure to obtain high parameters of milk production and reproduction. Knowledge of laboratory test results and relationships based on significant correlations between various milk and blood parameters may be very useful in veterinary diagnostics and helpful in cattle practice in order to protect animal health and the quality of milk production. The aim of the study was to analyze the correlation between selected hematological biomarkers such as white blood corpuscles (WBC), red blood corpuscles (RBC), hemoglobin concentration (HGB), hematocrit (HCT), platelets (PLT), erythrocyte mean corpuscular volume (MCV), mean corpuscular hemoglobin content (MHC), mean corpuscular hemoglobin concentration (MCHC) and selected quantitative-qualitative parameters of cow’s milk such as current milk production, somatic cells count (SCC), colony of bacteria forming units (CFU), milk fat (MF), milk protein (MP), milk lactose (ML), milk solids (S), solids non-fat in milk (SNF), daily milk production. Samples were collected three times at daily intervals from 11 clinically healthy late-lactation dairy cows obtaining 33 sets of test results. This repeated study of cows allowed for obtaining a homogeneous group in order to determine statistical correlations between selected blood and milk parameters. Many significant correlations were found between the examined parameters. In cows, significant positive correlations were recorded between milk production and HGB, HCT, MCV or MHC. Significant negative correlations were also found between SCC and HGB, SCC and HCT, SNF and MCV, SNF and MHC, and between MF and RBC.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

Heat pumps are increasingly becoming a key solution in the quest for decarbonization, offering a significant advantage over traditional boilers due to their superior energy efficiency. Not only can heat pumps provide both heating and cooling, but they also achieve thermal efficiencies exceeding 500%, which can seem to defy conventional expectations. The outdoor unit of a heat pump consists of about twenty main components, one of which is a complex network of copper pipes and sheets welded to valves, connectors, and other fittings. This set involves over thirty welded joints, highlighting a significant opportunity for reducing manufacturing time through process optimization. Copper is a critical material extensively used in various applications due to its excellent thermal and electrical conductivity. However, these very properties make welding copper particularly challenging, especially when aiming to automate and streamline industrial processes. Traditionally, connecting copper pipes and fittings is done through brazing, yet, alternative methods such as LASER welding, electron beam welding, resistance welding, friction welding, and ultrasonic welding also exist. This study focuses on the ultrasonic welding of copper, aiming to identify the optimal parameters that maximize the mechanical strength of overlapping joints and ensure effective tube sealing. Experimental results showed that for copper sheets, the best outcomes were achieved with a welding time of 3 s and a pressure of 6 bar. For tube sealing, the optimal conditions were a welding time of 3 s and a pressure of 4 bar. For both scenarios, the same variables were used, retention time of 0.62 s, initial pressure of 2 bar, retention pressure of 2 bar and sonotrode rising pressure of 3 bar. The analysis reveals that ultrasonic welding of copper can achieve both robust mechanical strength and reliable sealing, making it a promising technique for industrial applications.

Water resources provided by alpine glaciers are an important pillar for people living in the arid regions in the west of China. In this study, the HBV (Hydrologiska Byrans Vattenavdelning) light model was applied to simulate glacier mass balance and runoff in the Koxkar River Basin (KRB) on the south slope of Mt. Tumur, western Tianshan Mts.. Daily temperature and precipitation were calculated by multiple linear regressions and gradient-inverse distance weighting, respectively, based on in-situ observed data by automatic weather stations (AWSs) in the basin (2007–2009) and at four meteorological stations neighbering the basin (1959–2009). Observed daily air temperature and precipitation were taken as input data for the HBV model, which was calibrated using runoff in 2007/08 and 2009/10, and validated in 2008/09 and 2010/11. Generally, the model could simulate runoff very well. The annual glacier mass balance and runoff were calculated using the HBV model driven by interpolated meteorological data for the period of 1959–2009. The simulated glacier mass balance were reasonable when compared with those observed values at nearby glaciers, indicating a decrease trend of mass balance in the basin with an average value of –370.4 mm a^-1 since 1959. The annual runoff showed a slight increase trend (5.51 mm a^-1). Futher analysis indicated that the runoff is more sensitive to temperature than precipitation amuont in the Koxkar river basin.

The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. The tests were conducted for three sandstone varieties: Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching, however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities, as well as that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives.

Proton Exchange Membrane Fuel Cell (PEMFC) is a fast-developing battery technology, and the key to its reliability and lifespan improvement lies in the accurate assessment of durability. However, the degradation mechanism of PEMFC is hard to determine and its internal parameters are highly coupled. Thus, the development of the more accurate life prediction model that meets the actual scenarios is urgent to investigate. To solve this problem, a multi-feature fusion life prediction method based on Temporal Convolutional Network-Gated Recurrent Unit (TCN-GRU) is proposed. A TCN algorithm is used as the prediction base model, and two GRU modules are included to the model to strengthen the model expression ability and improve its predictive accuracy. Two widely recognized datasets and two operating conditions are utilized for model training and prediction, respectively. Comparisons are made with single-feature parameter models in terms of Root Mean Square Error (RMSE) and Determination Coefficient (R2). The results show that the prediction accuracy of the TCN-GRU multi-feature fusion model is higher than that of the single-feature models in terms of stability and anti-interference under both operating conditions. Furthermore, with the increase of input feature parameters, the TCN-GRU model is closer to the real value, which proves once again that the proposed model can meet the accuracy requirements of the life prediction of PEMFC.

Most research on colostrum quality and colostrum management focuses on maternal IgG transfer to the newborn calf. However, in addition to being a source of antibodies, colostrum has other components that influence passive immune transfer, nutrition, gut maturation, and thermoregulation. In this review, the constituents in the bovine colostrum, as well as their variation, are explored and it is discussed the biological role of colostrum on the newborn calf. Protein is the nutrient in higher concentration and fat is the nutrient with the most variation. There is a pronounced amplitude in the total solids content of colostrum, but the average concentration does not vary much between studies (24.7%). Bovine colostrum major components can vary with several factors, such as the region, season, breed, dry period length, and nutritional aspects of the dam. Bioactive components, cells, and microbiome variability are less understood, besides IgG. Regardless, they play crucial distinct roles in the physiological development of the newborn. However, a multi-interactive effect between these components, cells, and microorganisms is more likely to occur. Recently researched components in colostrum like miRNA, nucleo(t)sides, the milk fat globule membrane, oligosaccharides, minor proteins, and the microbiome are examples of promising interest areas of study.

Accurate and reliable mid-long runoff prediction (MLTRP) is of great importance in water re-sources management. However the MLTRP is not suitable in each basin and how to evaluate the applicability of MLTRP is still a question. Therefore, the total mutual information (TMI) index is developed in this study based on the predictor selection method using mutual information (MI) and partial MI (PMI). The relationship between the TMI and the predictive performance of five models is analyzed by applying five models in 222 forecasting scenarios in Australia. The results over 222 forecasting scenarios demonstrate that, compared with the MI, the developed TMI index can better represent the available information in the predictors, and has more significant negative correlation with the RRMSE with the correlation coefficient between -0.62 and -0.85. This means the model's predictive performance will become better along with the increase of TMI, and there-fore the developed TMI index can be used to evaluate the applicability of MLTRP. When TMI is more than 0.1, the available information in the predictors can support the construction of MLTRP models. In addition, the TMI is used to partly explain the difference of predictive performance among five models. In general, the complex models, which can better utilize the contained infor-mation, are more sensitive to the TMI, and have more significant improvement in terms of predic-tive performance along with the increase of TMI. This research can provide support for the study of MLTRP.

Since the 20th century, Japan has experienced a period of very rapid urbanization. Cities have experienced substantial densification and expansion, resulting in gradually elevated flood risk. Urban flooding has also occurred in most large cities in Japan, particularly in Tokyo. In response to this growing problem, much effort and resources have been spent on research and development aimed at understanding, simulating, and managing urban flood risk in Japan. The objective of this review is to summarize, discuss and share key outputs from some of the main research directions in this field, significant parts of which have been uniquely developed in Japan and only published in Japanese. After a general introduction to urban runoff modelling, in the next section, key historical works in Japan are summarized, followed by a description of the situation in Japan with respect to observations of precipitation and water level. Then, the storage function model approach is reviewed, including an extension to urban basins, as well as recent experiments with AI-based emulation in Japanese basins. Subsequently, we review the prospects of detailed hydrodynamic modelling involving high-resolution, vector-based Geographical Information System (GIS) data for the optimal description of the urban environment with applications in Tokyo. We conclude the paper with some future prospects related to urban flood risk modelling and assessment in Japan.

To investigate the bioactivities of fresh garlic and its processed product, black garlic, we conducted comparative analyses of antioxidant, anti-inflammatory, innate immune activation and anti-cancer activities, in addition to chemical composition (sugar, amino acid, polyphenol contents) of these materials. Simultaneous assay using neutrophil-like cells showed that fresh garlic exhibited antioxidant and innate immunostimulatory activities, whereas black garlic displayed a potent anti-inflammatory effect. The antioxidant activity index was correlated with phenol and flavonoid contents, while the innate immunostimulatory activity was correlated with fructan content. Furthermore, some black garlics with low fructose content were found to inhibit the proliferation of UM-UC-3 cancer cells, while other black garlics rich in fructose increased UM-UC-3 cell proliferation. It was shown that the thermal processing steps of fresh garlic could change the composition of sugars, antioxidants, and amino acids, which have different effects on neutrophil-like cells and UM-UC-3 cells, as well as on bioactivities.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Background: Cardiovascular (CV) morbidity and mortality are many times higher in chronic kidney disease (CKD), as well as IgA nephropathy (IgAN), than in the general population. The occurrence of metabolic syndrome (MetS) and metabolic risk factors are independent risk factors for CV disease and renal progression. The study aimed to determine the prognostic role of metabolic profiles in a homogenous group of CKD patients. Methods: One hundred and forty-five IgA nephropathy patients (92 male, 53 female, age 54.7 ± 13 years) with CKD stage 1-4 were investigated and followed for a median of 190 months. The composite (CV and renal) endpoints included all-cause mortality and any CV event such as stroke, myocardial infarction, revascularization (CV), end-stage renal disease, and renal replacement therapy (renal). Results: Patients with MetS had significantly more endpoint events (16/27 patients vs. 15/98 patients, p = 0.001) compared to the nonMetS group. Of the secondary endpoints (CV or renal separately), the rate of the renal and CV endpoints was significantly higher in the MetS group (p = 0.001 and p = 0.029). The primary endpoint independent predictors of survival were dyslipidemia, eGFR, hemoglobin, urine albuminuria, and diabetes mellitus, as determined by Cox regression analysis. Independent predictors of secondary renal endpoint were dyslipidemia, hemoglobin, urine albumin, and eGFR. Predictors of secondary cardiovascular endpoints were gender, BMI, and diabetes. Kaplan-Meier curves showed significant differences in MetS and non-MetS when examined at the combined endpoints (CV and renal) or at each endpoint separately. The primary endpoint rate increased significantly with the increased number of MetS components (MetS comp. 0 vs. MetS comp. 2+, primary endpoints, p = 0.012). Conclusion: Our results showed that the metabolic profile has a prognostic role not only for renal endpoints but also for CV endpoints in IgAN. BMI, hyperuricemia, hypertension, and diabetes have a predictive value for the prognosis of IgA nephropathy.

This study assessed the hydrological performance and runoff water quality of 12 green roof (GR) modular systems located at the Universidad de los Andes campus (Bogotá, Colombia). Based on 223 rainfall events spanning a 3-year period, average rainfall retention was 85% (SD = 25%). T-tests, Welch Test, multiple linear regressions and correlation analysis were performed in order to assess the potential effect of air temperature, substrate type, vegetation cover, relative humidity, antecedent dry weather period (ADWP), rainfall duration and rainfall maximum intensity. In some cases, GR design variables (i.e. growing media and type of vegetation) were found to be significant for describing rainfall retention efficiencies and, depending on the GR type, some hydrological variables were also correlated with the rainfall retention. Rainfall and GR runoff were monitored for Total Kjeldahl Nitrogen (TKN), Nitrates, Nitrites, Ammonia, Total Phosphorus (TP), Phosphates, pH, Total Dissolved Solids (TDS), Total Suspended Solids (TSS), Color, Turbidity, Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), Total Coliforms, metals and Poliaromatic Hydrocarbons (PAHs). The results obtained confirmed that GR systems have the ability to neutralize pH, but are source of the rest of the aforementioned parameters, excluding PAHs (with concentrations below detection limits), Ammonia, TSS, Se and Li, where differences with reference values (rainfall and plastic panel runoff) were not statistically significant. Substrate type, event size and rainfall regime are relevant variables for explaining runoff water quality.

Multiple indicators have been used to assess the degree of exposure of fish to anthropogenic chemicals in their stream habitats. We hypothesized that brook stickleback (Culaea inconstans) in a headwater stream receiving urban and agricultural runoff (South Fork Whitewater River, SFWR) would exhibit poorer condition, reduced reproductive fitness, and greater left side-to-right side morphological asymmetry (i.e., fluctuating asymmetry or FA) than would fish from a nearby headwater stream with a forested drainage basin (Garvin Brook). Male and female fish were collected from both streams just prior to spawning in 2013-2015. In 2013 and 2014, fish were assessed for overall condition (Fulton’s K) and internal measures of condition (hepatosomatic index, HSI) and reproductive fitness (gonadosomatic index [GSI], total egg count, egg weight). In 2015, measurements of head length, jaw length, eye diameter, pectoral fin length, and pelvic fin length were made on both sides of each fish for use in assessing degree of FA. We observed declining condition with fish size, increased liver size, and reduced egg counts and egg size in female brook stickleback in SFWR relative to those from Garvin Brook. SFWR females had significantly higher FA than Garvin females for all structures assessed except pelvic fin length. FA also was slightly higher for all structures in SFWR males compared to Garvin males, but differences were not significant. A composite FA index combining all measurements from an individual fish into a single value displayed highly significant differences for female fish (SFWR FA >> Garvin FA), but not for male fish (SFWR FA = Garvin FA). Exposure of brook stickleback to reduced water quality in SFWR during early development appears to increase morphological asymmetry in female (but not male) fish, and continuing exposure to compromised water quality throughout life impacts both general condition and reproductive fitness of stickleback, especially older female fish, in SFWR.

(1)Background：To date, no studies have epidemiologically examined whether the concentration of particulate matter (PM) 2.5 and its ionic components is related to the prevalence of skin symptoms. Therefore, this study aimed to clarify this association in patients with allergic diseases. (2)Methods: From February 1 to May 31, 2020, we evaluated the daily prevalence of skin symptoms in outpatients with allergic diseases being treated at Fukuoka Hospital, Fukuoka, Japan, and measured the concentration of PM2.5 and its ionic components. （3）Results: Univariate analysis showed a statistically significant association between skin symptoms and the concentration of PM2.5 and the ionic components SO42-, NH4+, K+, and Mg2+, and multivariate analysis showed a statistically significant association between the daily prevalence of skin symptoms and the concentration of the ionic components SO42- or Mg2+. (4)Conclusions: Our findings indicate that the concentration of some PM2.5 ionic components may affect skin symptoms in patients with allergic diseases.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

Watershed’s landscape features and climate features have a significant influence on the mountainous catchment’s hydrological response. This literature review synthesizes recent kinds of literature investigating associations between surface runoff and catchment’s landscape features, and the potential controls of climate variables, with an emphasis on mountainous regions. Such factors are significant controls on surface runoff through their influence on the rate of infiltration capacity, antecedent soil moisture conditions, and underlying bedrock structure. The literature review indicates that there are considerable issues that remain to be resolved in advance a concrete understanding of the influence of catchment’s characteristics on surface runoff response.

The current study was planned to simulate runoff due to the snowmelt in the Lidder River catchment of Himalayan region under climate change scenarios. A basic degree-day model, Snowmelt-Runoff Model (SRM) was utilized to assess the hydrological consequences of change in climate. The SRM model performance during the calibration and validation was assessed using volume difference (Dv) and coefficient of determination (R2). The Dv was found as 11.7, -10.1, -11.8, 1.96, and 8.6 during 2009-2014, respectively, while the R2 is 0.96, 0.92, 0.95, 0.90, and 0.94, respectively. The Dv and R2 values indicating that the simulated snowmelt runoff has a close agreement with the observed value. The simulated findings were also assessed under the different scenarios of climate change: a) increases in precipitation by +20 %, b) temperature rise of +2 °C, and c) temperature rise of +2 °C with a 20 % increase in snow cover. In scenario "b", the simulated results showed that runoff increased by 53 % in summer (April–September). In contrast, the projected increased discharge for scenarios "a" and "c" was 37 % and 67 %, respectively. In high elevation data-scarce mountain environments, the SRM is efficient in forecasting future water supplies due to the snowmelt runoff.

The Storm Water Management Model (SWMM) was used to evaluate the impact of urbanization, climate change, and implementation of Low Impact Developments (LIDs) at the Mahabad Dam watershed, Iran. Several scenarios of urbanization, with and without climate change impacts, in different locations were defined, including near outlet, middle, far end, and whole watershed. Climate change was considered to change the intensity of rainfall and increase evaporation. Vegetative swales were implemented as LIDs to evaluate their applicability to reduce pollutant loads. Digital Elevation Model (DEM) of the area was input into ArcGIS, and the watershed was delineated using the ArcSWAT extension to identify topographic features. Water quality properties were defined in the software, and each scenario was run for a twelve-hour simulation. The results indicated that urbanization affects the imperviousness of sub-catchments, and location of urbanization affects the amount and timing of runoff and pollutant yields. Fifty-percent urbanization near the watershed outlet resulted in 23.1% and 27.4% increases in runoff and pollutant loads, respectively. Fifty-percent urbanization in the middle resulted in 28.8% and 35.4% increases in runoff and pollutant loads; and, at the far end, 23.1% and 3.9% increases in runoff and pollutant loads were the result; Fifty-percent urbanizing the whole watershed gave 58.6% and 66.3% increases in runoff and pollutant loads, respectively; Under climate change scenarios (higher intensity, shorter duration rainfall) peaks occurred earlier. Moreover, results showed LIDs decreased pollution loads up to 25%.

BKW is a highly efficient Storage Function-type rainfall-runoff model that utilizes the steady-state storage (S) and outflow (Q) of a catchment at different rainfall intensities as the S-Q relation of the catchment. For the inundation nowcasting of urban areas under high-intensity, short-duration rainfall, a Storage Function-type model is a judicious choice. However, S-Q hysteresis exists in the catchment S-Q relation, and BKW is unable to exhibit hysteresis due to assuming that the S-Q relation of a catchment is a nonlinear relation. The S-Q hysteresis can influence the outflow estimation of BKW, reducing the model's accuracy. Through the evaluation of analytical solutions, we found that the change in rainfall intensity dominates the S-Q relation of a catchment. The S-Q relation during a rainfall event is a dynamic process rather than a monotonic nonlinear relation. By applying the dynamic S-Q relation in BKW, we improved BKW to become a highly efficient and accurate rainfall-runoff model for small urban catchments.

In this study a new approach for planning Micro-Catchment Water Harvesting (M.C.W.H.) systems for irrigation in semi-arid regions such as the Aegean islands, is presented. M.C.W.H. is a cheap solution for constructing irrigation infrastructure with zero energy cost in regions where water is scarce. The proposed approach introduces simple linear relationships for estimating the annual volume of water V_s collected mainly from the CA (Contributing Area), stored in the root zone (Infiltration Basin, IB), according to the annual rainfall and runoff depths, after having determined the ratio of areas of micro-catchment (MC) components i.e. λ= Α_CA/Α_ΙΒ and its whole area A_MC This procedure was applied in Paros island of the Cyclades complex in the middle of the Aegean sea in east Mediterranean. Besides, income-cost analysis was performed via NPV method for almond, peach and apricot trees. The new approach was proved versatile and easy to use. Besides, the investment turned out to be advantageous two years after the MCs construction.

In this work a modified version of the well-known Simple Water Balance (SWB) model, comprising here three parameters instead of one, was used. Although simple, the model was tested in large-scale river basins in east-central Greece, upstream two hydrometric stations. The available historic runoff records comprised 19 hydrologic years each, on a monthly basis. Thirteen among them were used for calibrating the model, whereas the six subsequent, for validating it. Two different efficiency criteria were used as a measure of performance of the modified model. Their values, calculated for both calibration and validation stages, were close and relatively high. Thus, keeping in mind both the size and complexity of the river basins studied, one can conclude that the modified model, despite its simplistic concept and lumped form, fits satisfactorily the historic runoff series.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

The Soil Conservation Service - Curve Number (SCS-CN) method is extensively used to calculate the runoff from rainfall over a large catchment over the world. Slope is an important criterion for runoff but a very few attempts have been made to evaluate the effect of slope on the CN with runoff potential. The objective of this paper is to summarise the historical review on the effects of slope on CN and runoff potential in various regions by the hydrologists. This paper also depicts that how the various researchers proved the importance of consideration of slope for CN and runoff estimation. In addition, paper highlights the key features of research in future like to classify the watersheds on slope based CN, accurate Antecedent Moisture Condition (AMC) and proper initial abstraction in the various regions etc. Considering these parameters an accurate runoff estimation can be predicted and managed properly in the urban watersheds.

The prominent cultivation of lemongrass relies on the pharmacological incentives of its essential oil. The lemongrass essential oil (LEO) has a significant amount of citral (mixture of geranial and neral), isoneral, isogeranial, geraniol, geranyl acetate, citronellal, citronellol, germacrene-D, and elemol in addition to numerous other bioactive compounds. These components confer various medicinal activities to LEO including antifungal, antibacterial, antiviral, anticancer, and antioxidant properties. These attributes are commercially exploited in pharmaceutical, cosmetics, and food preservations industries. Furthermore, the employment of LEO in the treatment of cancer opens a new vista in the field of therapeutics. Although different LEO components have shown promising anticancer activities in vitro, these effects have not been assessed yet in humans. Further studies on the anticancer mechanisms exerted by lemongrass components are required. The present review intends to provide a timely discussion on the relevance of lemongrass extracts in cancer and health treatment, and in food industry applications.

The runoff coefficient (C) represents the relationship between the surface runoff volume and the precipitated volume. It is used in engineering projects for flood estimation methods. Although C values are tabulated and consecrated in hydrological engineering, as if they were constant, they may not correspond to the reality, because in the same catchment, they can vary according to the intensity, temporal and spatial distribution of precipitation events, humidity conditions, and ground cover. This study had the objective of analyzing extreme events of precipitation and the corresponding flows to obtain experimental runoff coefficients (C) and compare them with the tabulated values. The study was conducted in four experimental catchments in the State of São Paulo, Brazil, with different land uses and soils. The runoff coefficients (C) were obtained from the analysis of hydrograms and using a digital filter, which allowed the separation of the direct runoff, of the total flow. When analyzing flow and precipitation data in different seasons of the year, selecting events of the floods of catchments and separating the flows, we observed a variation of the flow coefficient values, different from those obtained from tables.

In addition to changes in the amount of rain, changes in land use upstream are considered a factor that directly affects the maximum runoff flow in a basin, especially in areas that have experienced floods and flash floods. This research article presents the application of the SWAT model to assess runoff in areas that have experienced flash floods, in order to analyze the proportion of land use change to the maximum runoff. Study areas that had experienced flash floods were in 3 basins in Thailand (Lam Saphung Basin, Phrom River Basin, and Chern River Basin Part 1 which is a subbasin of the Nam Chi River Basin). This study analyzed two main factors that influence runoff in the river basin: Changes in rainfall and changes in land use by considering 2 simulation situations.: (1) Changes in land use affecting runoff assessed by considering land use maps in 2006, 2008, 2010, 2015, 2017, 2019, and 2021 when using rainfall data only in the year 2021 for all cases, and (2) Changes in the amount of rainfall influencing runoff by considering the rainfall record in 2006, 2008, 2010, 2015, 2017, 2019, and 2021 when using the land use data only in the year 2021 for all cases. The results of the study found that the SWAT model can be effectively applied to estimate annual runoff in areas that have experienced flash floods under 8 parameters with R2 values of 0.74, 0.82 and 0.74 for the Lam Saphung River Basin and the Phrom River Basin and the Chern River Basin Part 1 respectively. In addition, it was found that the proportion of land use changes that involved changes from forest areas to residential areas was the greatest from 2008 to 2010 in the Phrom River Basin and Chern River Basin Part 1. This resulted in an increase in the maximum runoff amount of 77.78% and 46.87%, respectively. When land use was constant, it was found that the rainfall in 2010, which was the highest, also had the greatest impact on the runoff in all 3 areas.

Nowadays, great attention has been attributed to the study of runoff and its fluctuation over space and time. There is a crucial need for a good soil and water management system to overcome the challenges of water scarcity and other natural adverse events like floods and landslides, among others. Rainfall-runoff modeling is an appropriate approach for runoff prediction, making it possible to take preventive measures to avoid damage caused by natural hazards such as floods. In the present study, several data driven models, namely: Multiple linear regression (MLR), Multiple adaptive regression splines (MARS), Support vector machine (SVM), and Random Forest (RF), were used for rainfall-runoff prediction of the Gola watershed, located in the south-eastern part of the Uttarakhand. The performance of the models was evaluated based on the coefficient of determination (R2), root mean square error (RMSE), Nash-Sutcliffe efficiency (NSE), and percent bias (PBAIS) indices. In addition to the numerical comparison, the models were evaluated and their performances were evaluated base on graphical plotting, i.e., line diagram, scatter plot, Violin plot, relative error plot and Taylor diagram (TD). The comparison results revealed that the four heuristic methods gave higher accuracy than the MLR model. Among the machine learning models, the RF (RMSE (m3/s), R2, NSE, and PBIAS (%) = 6.31, 0.96, 0.94, and -0.20 during the training period, respectively, and 5.53, 0.95, 0.92, and -0.20 during the testing period, respectively) surpassed the MARS, SVM, and the MLR models in forecasting daily runoff for all cases studies. Among all four models, the RF model outperformed in the training and testing periods. It can be summarized that the RF model is best-in-class and delivers a strong potential for runoff prediction of the Gola watershed.

This study was designed to assess the reliability of geographic information using satellite image information in ungauged basins. For this, this study constructed geographic information using actual gauged data and satellite information data and conducted runoff analysis through S-RAT, a rainfall–runoff model, and performed the comparison and analysis of geographic information and runoff data. For actual gauged data, the gauged geographic information of the Water Resources Management Information System (WAMIS) was collected, and for satellite information, the image information of moderate-resolution imaging spectroradiometer (MODIS) observation sensor loaded on Terra Satellite was collected. As analysis areas, three basins where mountains occupy more than 80% and another three basins where urban areas occupy more than 7% in the Han River basin were selected. According to the analysis result, the gauged information and satellite image information showed great difference in runoff, maximum 50% in peak flood and maximum 17% in total flood, in the rivers with many urban areas, while the runoff difference in the rivers with many mountains showed maximum 13% in peak flood and 4% in total flood. What showed the greatest difference in image information was land use, and it turned out that the MODIS satellite recognized the urban rivers as cities for more than maximum 60% compared to WAMIS-gauged data. Meanwhile, in the forest area, the MODIS satellite image showed error of less than 5% of the WAMIS-gauged data, which indicates that it has higher applicability in Mountain Rivers.

Performance of flow through orifices on a perforated distribution pipe between periods with and without partial clogging (submersion of part of the distribution pipe) was compared. The distribution pipe directly receives runoff and delivers it to an underground infiltration bed. Partial clogging appeared in winter but reduced in summer. Performance was defined as flow rate divided by l_eff (h_(d,mean)^0.5) where h_(d,mean) is the mean pressure head that drives flow and l_eff is the effective pipe length (length of water column with pipe water volume and the pipe cross-sectional area). ANCOVA (ANalysis of COVAriance) was adopted to examine the clogging effects with flow rate plotted against l_eff (h_(d,mean)^0.5) . Partial clogging had a significant effect on pipe performance during periods of low or no rainfall. However, if only data during larger storms was considered, little evidence showed that partial clogging had effects on pipe delivery performance. Partial clogging might be caused by leaves accumulated in the lower section of the pipe in winter, and its effect was insignificant when water level rose in the pipe, utilizing significantly more orifices on the distribution pipe, thus the effect from the clogged portion had negligible impact on system performance. Larger storms might also provide the required flow rate to move the debris block thus exposing the orifices. Partial clogging did not increase the tendency of overflow; therefore, current maintenance schedule was sufficient to keep the distribution pipe at satisfactory performance even though partial clogging can exist.

Coccomyxa subellipsoidea KJ (C-KJ) is a green alga with unique immunoregulatory characteristics. Here, we investigated the mechanism underlying the modification of T cell function by C-KJ components. The water-soluble extract of C-KJ was fractionated into protein (P) and sugar (S) fractions [acidic (AS), basic (BS), and neutral (NS)]. These fractions were used for the treatment of peripheral blood mononuclear cells stimulated with toxic shock syndrome toxin-1. Transcriptome analysis revealed that both P and AS enhanced the expression of the genes encoding metallothionein (MT) family proteins, inflammatory factors, and T helper (Th) 17 cytokine and suppressed that of those encoding Th2 cytokines in stimulated T cells. The kinetics of MT1 and MT2A gene expression showed a transient increase in MT1 and maintenance of MT2A mRNA after T cell stimulation in the presence of AS. The kinetics of Th17-related cytokine secretion in the early period were comparable to those of MT2A mRNA. Furthermore, our findings revealed that static, a STAT-3 inhibitor, significantly suppressed MT2A gene expression. These findings suggest that the expression of MTs is involved in the immune regulatory function of C-KJ components, which is partially regulated by Th17 responses, and may help develop innovative immunoregulatory drugs or functional foods.

For the purpose of clean energy hydropower development, the construction of reservoirs has been continuously promoted in the Jinsha River basin for many years, and how the reservoirs affect the water and sediment process is a very necessary topic to study. This study is based on the gauged water and sediment data (span from the 1960’s to 2020) at Shigu, Panzhihua, and Xiangjiaba stations downstream located in the trunk channel of the river, and uses Mann-Kendall trend test method and double cumulative curve method to comprehensively judge the variation trends of runoff and suspended sediment load and reveal their credible mutation years. The linear regression method is used to reveal the variation characteristics of the relationship between water and sediment before and after the abrupt change years. The results show that the variations in runoff at Shigu and Panzhihua stations have significant and relatively obvious increasing trends, respectively, and that at Panzhihua station has a mutation year of 1985. The runoff at Xiangjiaba Station slightly increased but not significantly. The variation of suspended sediment load showed a temporal and spatial differentiation. The variation of sediment discharge at Shigu Station showed an increasing trend with a mutation year of 1997. For Panzhihua Station, it showed an increasing trend before 1998, but has significantly decreased since 1998. The fluctuation of sediment transport at Xiangjiaba Station was significant before 1998, but the trend is unclear. In the period of 1998−2020, it showed a significant decreasing trend, especially since 2013, when the mean annual suspended sediment load only accounted for 0.61% of its multi-year average. The variations of mean annual sediment concentration and sediment inflow coefficient at the hydrological stations is consistent with the variation trend of sediment transport. Before 2013, the correlation between water and sediment was strong, but thereafter it was extremely weak. The two sudden years of 1998 and 2013 are consistent with the year when large reservoirs were built in the river basin. The construction of large reservoirs and their large amount of sediment retention are the key reasons for the sudden changes in the water-sediment relationship and the sharp decrease in sediment transport in the downstream reach of the reservoir dam. The climate and underlying surface changes in the study area are not significant, and their impact on the water and sediment processes in the watershed is limited.

Hydrological models have been widely used for many purposes in water sector projects, including streamflow prediction and flood risk assessment. Among the input data used in such hydrological models, the spatial-temporal variability of rainfall datasets has a significant role on the final discharge estimation. Therefore, accurate measurements of rainfall are vital. On the other hand, ground-based measurement networks, mainly in developing countries, are either nonexistent or too sparse to capture rainfall accurately. In addition to in-situ rainfall datasets, satellite-derived rainfall products are nowadays available globally with high spatial and temporal resolution. An innovative approach called SM2RAIN that estimates rainfall from soil moisture data has been applied successfully to various regions. In this study, firstly soil moisture content derived from the Advanced Microwave Scanning Radiometer for the Earth observing system (AMSR-E) is used as input into the SM2RAIN algorithm to estimate daily rainfall, SM2R-AMSRE, at different sites in the Karkheh river basin (KRB), southwest Iran. Secondly, the SWAT (Soil and Water Assessment Tool) hydrological model is applied to simulate runoff using both ground-based observed rainfall and SM2R-AMSRE rainfall as input. The results reveal that the SM2R-AMSRE rainfall data are, in most cases, in good agreement with ground-based rainfall, with correlations R ranging between 0.58 and 0.88, though there is some underestimation of the observed rainfall, due to soil moisture saturation, not accounted for in the SM2RAIN equation. The subsequent SM2R-AMSRE- SWAT- simulated monthly runoff reproduces well the observations at the 6 gauging stations (with coefficient of determination, R² > 0.72), though with slightly worse performances in terms of bias (Bias) and root-mean-square error (RMSE) and, again, some systematic flow underestimation than the SWAT model with ground-based rainfall input. Furthermore, rainfall estimations of two satellite products of the Tropical Rainfall Measuring Mission (TRMM), 3B42 and 3B42RT, are used in the calibrated SWAT- model. The monthly runoff obtained with 3B42- rainfall have 0.39< R2 < 0.70 and are slightly better than those obtained with 3B42RT- rainfall, but not as good as the SM2R-AMSRE- SWAT- simulated runoff above. Therefore, in spite of the afore-mentioned limitations, using SM2R-AMSRE rainfall data in a hydrological model like SWAT, appears to be a viable approach in basins with limited ground-based rainfall data.

Motivation: The visualization of biological data is a fundamental technique that enables researchers to understand and explain biology. Some of these visualizations have become iconic, for instance: tree views for taxonomy, cartoon rendering of 3D protein structures, or tracks to represent features in a gene or protein, for instance in a genome browser. Nightingale provides visualizations in the context of proteins and protein features. Results: Nightingale is a library of re-usable data visualization web components that are currently used by UniProt and InterPro, among other projects. The components can be used to display protein sequence features, variants, interaction data, 3D structure, etc. These components are flexible, allowing users to easily view multiple data sources within the same context, as well as compose these components to create a customized view. Availability: Nightingale examples and documentation are freely available at https://ebi-webcomponents.github.io/nightingale/. It is distributed under the MIT license, and its source code can be found at https://github.com/ebi-webcomponents/nightingale.

Hydro-climatic projections in West Africa are attributed with high uncertainties that are difficult to quantify. This study assesses the influence of the parameter sensitivities and uncertainties of three rainfall runoff models on simulated discharge in current and future times using meteorological data from 8 Global Climate Models. The IHACRES Catchment Moisture Deficit (IHACRES-CMD) model, the GR4J and the Sacramento model were chosen for this study. During model evaluation, 10,000 parameter sets have been generated for each model and used in a sensitivity and uncertainty analysis using the Generalized Likelihood Uncertainty Estimation (GLUE) method. Out of the three models, IHACRES-CMD recorded the highest Nash-Sutcliffe Efficiency (NSE) of 0.92 and 0.86 for the calibration (1997-2003) and the validation (2004-2010) period respectively. The Sacramento model was able to adequately predict low flow patterns on the catchment while the GR4J and IHACRES-CMD over and under estimate low flow respectively. The use of multiple hydrological models to reduce uncertainties caused by model approaches is recommended along with other methods of sustainable river basin managements.

In marine ecosystems communication among microorganisms is crucial since the distance is significant if considered on a microbial scale. One of the ways used by microorganism cells to reduce this gap is the production of extracellular vesicles. Marine bacteria release extracellular vesicles (EVs), small membrane-bound structures of 50 to 250 nm diameter, into their surrounding environment. The vesicles contain various cellular compounds, including lipids, proteins, nucleic acids, and glycans. EVs may mediate the communication between microorganisms in aquatic environments thus influencing ecosystem function and determining the structure and composition of microbial populations. This review will focus on marine bacterial EVs analysing their structure, composition, functions, and applications.

Cows produce saliva in very large quantities to lubricate and facilitate food processing. Estimates indicate an amount of 50-150 liter per day. Human saliva has previously been found to contain numerous antibacterial components, such as lysozyme, histatins, members of the S-100 family and lactoferrin to limit pathogen colonization. Cows are dependent of a complex microbial community in their digestive system for food digestion. We wondered how this would influence the content of their saliva. We therefore sampled saliva from five humans and both nose secretions and saliva from six cows and separated the saliva on SDS-PAGE gradient gels and analyzed the major protein bands by LC-MS/MS. The cow saliva was found to be dominated by a few major proteins only, the carbonic anhydrase 6, a pH stabilizing enzyme, and the short palate, lung and nasal epithelium carcinoma-associated protein 2A (SPLUNC2A), also named bovine salivary protein 30kDa (BSP30). This latter protein has been proposed to play a role in local antibacterial response by binding bacterial lipopolysaccharide (LPS) and inhibit bacterial growth, but may instead according to more recent data instead have primarily surfactant activity. Numerous peptide fragments of mucin-5B were also detected in the MS analysis. However, mucins stain poorly by the gel staining solution and they are large and have difficult to enter regular gels why their presence easily are overseen. Interestingly, no major band on gel was detected representing any of the antibacterial proteins indicating that cows may produce them at very low levels not to harm the microbial flora of their digestive system. The nose secretions of the cows primarily contained the odorant protein, a protein thought to be involved in enhancing the sensing of smell by the olfactory receptors to enhance the possibility to quickly sense potential poisonous food components. High levels of secretory IgA was also found in one sample of cow mouth drippings indicating a strong upregulation during an infection. The human saliva we more complex containing both secretory IgA, amylase, carbonic anhydrase 6, lysozyme, histatins and a number of other less abundant proteins.

A novel approach to the remote-control system for the compact multi-crystal energy-dispersive spectrometer for x-ray emission spectroscopy (XES) applications has been developed. This new approach is based on asynchronous communication between software components and on reactive design principles. In this paper, we identify the challenges we have faced, our solution to them as well as the implementation and future development prospects. The main motivation of this work was the development of a new holistic communication protocol that can be implemented to control various hardware components.

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

Green Stormwater Infrastructure (GSI), a sustainable engineering design approach for managing urban stormwater runoff, has long been recommended as an alternative to conventional conveyance-based stormwater management strategies to mitigate the adverse impact of sprawling urbanization. Hydrological and hydraulic simulations of small-scale GSI measures in densely urbanized micro watersheds require high-resolution spatial databases of urban land use, stormwater structures, and topography. This study presents a highly resolved Storm Water Management Model developed under considerable spatial data constraints. It evaluates the cumulative effect of the implementation of dispersed, retrofitted, small-scale GSI measures in a heavily urbanized micro watershed of Costa Rica. Our methodology includes a high-resolution digital elevation model based on Google Earth information, whose accuracy was sufficient to determine flow patterns and slopes, as well as to approximate the subsurface stormwater structures. The model produced satisfactory results in event-based calibration and validation, which ensured the reliability of the data collection procedure. Simulating the implementation of GSI shows that dispersed, retrofitted, small-scale measures could significantly reduce impermeable surface runoff (peak runoff reduction up to 40%) during frequent, less intense storm events and delay peak surface runoff 5-10 minutes. The presented approach can benefit stormwater practitioners and modelers conducting small scale hydrological simulation under spatial data constraint.

The outcomes of the 2015 Paris Agreement triggered a number of climate impact assessments, such as for floods and droughts, to focus on future time frames corresponding to the years of reaching specific levels of global warming. Yet, the links between the timing of the warming levels and the corresponding greenhouse gas concentration pathways to reach them, remain poorly understood. To address this gap, we compare projected changes of annual mean, extreme high and extreme low river discharges in Europe at 1.5°C and 2°C under scenarios RCP8.5 and RCP4.5 from an ensemble of Regional Climate Model (RCM) simulations. The statistical significance of the difference between the two scenarios for both warming levels is then evaluated. Results show that in the majority of Europe (>95% of the surface area for the annual mean discharge, >98% for high and low extremes), the changes projected in the two pathways are statistically indistinguishable. These results suggest that in studies of changes at specific warming levels the projections of the two pathways can be merged into a single ensemble without major loss of information. With regard to the uncertainty of the unified ensemble, findings show that the projected changes of annual mean, extreme high and extreme low river discharge are statistically significant in large portions of Europe.

As a procedure deriving UH (unit hydrograph), the root selection method necessitates only storm runoff data. However, this method must deal with the uncertainty related to the noise fluctuation of runoff ordinates and derive one optimal UH from many storms. This study proposes a procedure that applies the Savitzky-Golay filter to smooth the noise fluctuation of the runoff ordinates and uses the linear combination of UHs from individual storms to derive an optimal UH. The proposed method is applied to the storms of the Nenagh River basin in Ireland. The applicability of the Savitzky-Golay filter for smoothing the noise fluctuation of storm runoffs is examined by means of the Nash-Sutcliffe efficiency index. Furthermore, the root selection method is extended to also estimate IUHs. The results show that the adoption of the Savitzky-Golay filter improves the applicability of the root selection method and that the optimal UH predicts accurately the time-to-peak and peak discharge.

Aquaculture contributes to the sustainable development of food security, marine resource conservation, and economy. Shifting aquaculture feed from fish meal and oil to terrestrial plant-derivatives may result in cost savings. However, many carnivorous fish cannot be sustained on plant-derived materials, necessitating the need for the identification of important factors for farmed fish growth and to investigate whether components derived from terrestrial plants can be used in feed. Herein, we focused on the carnivorous fish leopard coral grouper (P. leopardus) to identify the essential growth factors and clarify their intake timing from feeds. Furthermore, we evaluated the functionality of starch, which are easily produced by terrestrial plants. Results reveal that carbohydrates, which are not considered essential for carnivorous fish, can be introduced as a major part of artificial diet. The development of artificial feed using starch offers the possibility of increasing the growth of carnivorous fish in aquaculture.

Currently, the use of numerical models for reproducing the landscape evolution of a river basin is part of the day-by-day research activities of fluvial engineers and geomorphologists. However, despite landscape modelling is based on a rather long tradition, and scientists and practitioners are trying to schematize the processes involved in the evolution of a landscape since decades, there is still the need for improving both the knowledge of the physical mechanisms and their numerical coding. The present review focuses on the first aspect, discussing the main components of a landscape evolution model and their more common schematizations, presenting possible open questions to be addressed towards an improvement of the reliability of such kind of models in describing the fluvial geomorphology.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Revenue-sharing (RS) contracts are a common approach to incentivize innovation of upstream suppliers by addressing the uneven profit distribution between upstream and downstream firms. Considering the possible overconfidence characterizing decision makers in the supply chain, we investigate the effect of the RS contract and the tendency of overconfidence of supply chain members on the investment in R&D of key components of products in the context of an upstream supplier that is the leader in the R&D and production of key components. We find that regardless of the bargaining power of either party, a RS contract can increase the R&D investment in key components. Regarding the effects of overconfidence of either downstream manufacturer or up-stream supplier, it can increase the R&D investment in key components. Supplier (manufacturer) overconfidence can harm their own profits but increase the profits of the manufacturer (supplier), and when the level of overconfidence is below a certain threshold, the damage to their own profits is less than the increase in each other's profits, thus benefiting the whole supply chain. In addition, we also find a joint effect of RS contracts and overconfidence: when the bargaining power of the supplier is low, the RS contract has a certain compensatory effect on the loss of their own profits caused by overconfidence.

When there is uncertainty in the value of parameters of the input random components of a stochastic simulation model, two-level nested simulation algorithms are used to estimate the expectation of performance variables of interest. In the outer level of the algorithm (n) observations are generated for the parameters, and in the inner level (m) observations of the simulation model are generated with the value of parameters fixed at the value generated in the outer level. In this article, we consider the case in which the observations at both levels of the algorithm are independent, showing how the variance of the observations can be decomposed into the sum of a parametric variance and a stochastic variance. Next, we derive central limit theorems that allow us to compute asymptotic confidence intervals to assess the accuracy of the simulation-based estimators for the point forecast and the variance components. Under this framework, we derive analytical expressions for the point forecast and the variance components of a Bayesian model to forecast sporadic demand; and we use these expressions to illustrate the validity of our theoretical results by performing simulation experiments using this forecast model.

Exogenous miRNAs derived from dietary substances have been shown to be orally transferred to the mammalian system and proven to remain active to regulate host-gene expression. This way they have become an active area of research as functional food components and aspects for dietary supplementation. They are being studied as a new class of metabolically targeted therapeutics that work through diet manipulation and may hold promise for a therapeutic approach in reducing the risk of life-threatening diseases. However, a substantial amount of evidence also defies this dietary miRNA concept in terms of their absorption, bioavailability, cellular uptake and its physiological effects in the mammalian system. But recent advances in the identification of some unique sequence and structural characteristics of dietary miRNAs and a deeper understanding of their stability in host peripheral blood for its cellular uptake have strengthened the whole concept. The review comprehensively summarizes the mechanism for miRNA extracellular transport, absorption through the gastrointestinal tract (GI), stability in peripheral blood, and cellular uptake in mammalian cells. It recapitulates the shreds of evidence, related to the influence of dietary miRNAs on gene expression based on the source of the origin (plant vs animal), and compares their cross-kingdom behaviour in terms of their unique sequence and stem-loop structure properties that help them to get stabilized in the mammalian system. The review also summarizes the parameters required for maintaining the sustainable uptake and bioavailability of the dietary miRNAs with existing examples of successful in-vivo and in-vitro delivery of dietary miRNA for augmented therapy. Lastly, it provides an overview of the available and required databases, webserver, and tools that can be used for the successful identification of potential dietary miRNA candidates.

Reassessment of the fatigue life for wind turbines structural components is typically performed using deterministic methods with the same partial safety factors as used for the original design. However, in relation to life extension, the conditions are generally different from the assumptions used for calibration of partial safety factors; and using a deterministic assessment method with these partial safety factors might not lead to optimal decisions. In this paper, the deterministic assessment method is compared to probabilistic and risk-based approaches, and the economic feasibility is assessed for a case wind farm. Using the models also used for calibration of partial safety factors in IEC61400-1 ed. 4 it is found that the probabilistic assessment generally leads to longer additional fatigue life than the deterministic assessment method. The longer duration of the extended life can make life extension feasible in more situations. The risk-based model is applied to include the risk of failure directly in the economic feasibility assessment and it is found that the reliability can be much lower than the target for new turbines, without compromising the economic feasibility.

Nucleolin is an RNA binding protein that is involved in many post-transcriptional regulation steps of messenger RNAs in addition to its nucleolar role in ribosomal RNA transcription and assembly in pre-ribosomes. Acetylated nucleolin was found to be associated with nuclear speckles and to co-localize with the splicing factor SC35. Previous nuclear pull down of nucleolin identified several splicing components and factors involved in RNA polymerase II transcription associated with nucleolin. In this report, we show that these splicing components are specifics of the pre-catalytic A and B spliceosomes, while proteins recruited in the Bact, C and P complexes are absent from the nucleolin interacting proteins. Furthermore, we show that acetylated nucleolin co-localized with P-SF3B1, a marker of co-transcriptional active spliceosomes. P-SF3B1 complexes can be pulled down with nucleolin specific antibodies. Interestingly, the alternative splicing of Fibronectin at the IIICS and EDB sites was affected by nucleolin depletion. These data are consistent with a model where nucleolin could be a factor bridging RNA polymerase II transcription and assembly of pre-catalytic spliceosome similarly to its function in the co-transcriptional maturation of pre-rRNA.

Accurate monthly runoff estimation is fundamental in water resources management, planning, and development, resulting in preventing and reducing water-related problems, such as flooding and drought. This article evaluates the performance of the monthly hydrological rainfall-runoff model, GR2M model, in Thailand's southern basins. The GR2M model requires only two parameters, and no prior research has been reported on its application in this region. The 37 runoff stations, which are distributively located in three sub-watersheds of Thailand's southern region, namely; Thale Sap Songkhla, Peninsular-East Coast, and Peninsular-West Coast, were selected as study cases. The available monthly hydrological data of runoff, rainfall, air temperature from the Royal Irrigation Department (RID) and the Thai Meteorological Department (TMD) were collected and analyzed. Thornthwaite method was utilized for the determination of evapotranspiration. The model's performance was conducted using three statistical indices: Nash-Sutcliffe Efficiency (NSE), Correlation Coefficient (r), and Overall Index (OPI). The model's calibration results for 37 runoff stations gave the average of NSE, r, and OPI of 0.637, 0.825, and 0.757, and those values for verification of 0.465, 0.750, and 0.639, respectively. It indicated a model's acceptable performance and could apply the GR2M model for determining monthly runoff variation in this region. The spatial distribution of X1 and X2 values was conducted by using IDW method. It was susceptible to the X1 value and X2 value of approximately more than 0.90 gave the higher model's performance.

Keywords: Antibacterial activity, Antioxidant activity, Bioactive compounds, Elementary analysis, Nutritional and phytochemical composition, Seaweed.

The fixed and random effects models are popular methods for identifying the causal effects of treatment. First, I introduce the two-way fixed effects model and show a class of the estimators for the random effects models. Misidentification may occur in these models due to the treatment effect heterogeneity. Then, I propose the differential error component models to address such problems while the models exclude the fixed effects of units and time periods and consider the random effects of units and time periods. Meanwhile, I present a simulation of a staggered design and revisit the application in (De Chaisemartin and D'Haultfoeuille, 2020). The results demonstrate that one additional newspaper increases the 0.31% average effect of the presidential turnout and the 1.05% average effect when the newspapers’ changes are non-negative, where the proposed estimators are robust and efficient.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

The paper investigated the components of savings accumulation in Nigeria over the period 1980 to 2017. Secondary data were collated from World Development Index (WDI). In evaluating the objectives, the study employed the Auto Regressive Distributive Lag (ARDL) and Vector Error Correction Model (VECM) estimation methods. The key findings of the study show that the components of savings identified in literature understudied in the paper specifically, GDP per capita, foreign direct investment, financial deepening, interest rate, inflation rate exchange rate significantly influence savings accumulation in Nigeria either in short run, long run or both. Financial deepening was found statistically significant but influences savings negatively. Inflation rate was statistically insignificant although negative. The result from the VECM causality test revealed that short run and long run causal relationship exist between savings and the afore mentioned components in Nigeria. Hence, the study recommends careful manipulation of the identified savings components in a manner that they will not yield a counterproductive result in the economy rather contribute to the growth of savings and ultimately, the growth of Nigeria economy as a whole. It further recommends that the Nigerian government through its financial institutions encourage savings from both small and big savers which to large extent will assuage the perceived undeserved influence of financial deepening on savings accumulation.

Ionospheric delay has been a critical issue that limits the accuracy of GNSS precise positioning and navigation for single-frequency users, especially in mid- and low-latitude regions where irregularity of ionosphere is often significant. Kriging spatial interpolation techniques have been recently introduced to model the spatial correlation and variability of ionosphere, which intrinsically assume that the ionosphere field is stochastically stationary but does not take the random observational errors into account. In this paper, by treating the spatial statistical information on ionosphere as prior knowledge and based on TEC semivariogram analysis, we use Kriging techniques to spatially interpolate TEC values. By assuming that the stochastic models of both the ionospheric signals and measurement errors are only known up to some unknown factors, we propose a new Kriging spatial interpolation method with unknown variance components for both the signals of ionosphere and TEC measurements. Variance component estimation has been integrated with Kriging to reconstruct regional ionospherical delay. The method has been applied to data from the Crustal Movement Observation Network of China (CMONOC) and compared with the ordinary Kriging and polynomial interpolations with spherical cap harmonic functions, polynomial functions and low-degree spherical harmonic functions. The results have shown that the interpolation accuracy of the new proposed method is better than the ordinary Kriging and polynomial interpolation by about 1.2 TECU and 0.7 TECU, respectively. The root mean squared error of the proposed new Kriging with variance components is within 1.5 TECU and is smaller than those from other methods under comparison by about 1 TECU. When compared with ionospheric grid points, the mean squared error of the proposed method is within 6 TECU and smaller than Kriging, indicating that the proposed method can produce more accurate ionospheric delays and better estimation accuracy.

This article is based on the findings of a mapping project of portions of the runoff agricultural system in the Levant in during the Byzantine period, the purpose of which was to study the resemblance between the components of that system in the desert and those in the sedentary land. These include dammed wadis, specific agricultural installations and settlement sites, among them chapels and livestock pens. The focus on agricultural installations has led to the possibility of dating the peak of the agricultural system’s functioning to the second half of the sixth century CE. Two assumptions will be put to the test: (1) that the establishment of the agricultural system overlapped the climate crisis in Europe that compromised food production in most areas of the Byzantine Empire – but not in the Levant, which for a certain period became a food supplier; (2) that the Church, as the emissary of the empire, stood at the head of the system.

Soil erosion is one of the biggest problems in the agricultural sector that can affect ecosystems and human societies. A field of 50 slope was selected to study the runoff, soil and nutrients’ loss as well as crop productivity in different treatments (conventional tillage (CT) vs. no-tillage (NT), plant vs. no plant cover, contour cultivation (CC) vs. perpendicular to the contour cultivation, (PC) under natural rainfall. The experiment was conducted in central Greece in two cultivation periods. In autumn, the field was cultivated with intercropping Triticosecale and Pisum sativum and in spring with Sunflower. The total rainfall was 141.4 mm in the 1st year and 311 mm in the 2nd. We found that runoff in the treatment of no tillage with contour cultivation was 85% lower in both years compared to the no tillage-no plant control. Therefore, the contour cultivation-no tillage treatment had a positively effect in decreasing phosphorus and potassium concentrations lost from soil: indeed, there was a decrease by 55% and 62% in P and K, respectively, in the NT compared to the CC treatments. We conclude that the NT-CC treatment with plant cover was the most effective in reducing water runoff, soil nutrients’ loss and increasing yield.

Cultivated land plays an important role in water and soil loss in the earth-rocky mountainous region, northern China, however, its responses to soil control measures and rainfall characteristics are still not fully understood. In this study, 85 erosive rainfall events in 2011-2019 were grouped into three types, and the responses of runoff and soil loss on five cultivated plots with different slopes in the upstream catchment of the Miyun Reservoir to soil conservation measures and rainfall regimes were evaluated. Results found that event-averaged runoff depths and soil loss rates on the five plots ranged from 7.05 mm to 0.03 mm and from 300.51 t km-2 to 0.37 t km-2 respectively, depending on rainfall regimes, soil conservation measures, and slope gradients. The high occurring frequency (i.e., 72.94%) rainfall regime A with short rainfall duration (RD), low rainfall amount (P), and high mean rainfall intensity (Im) yielded lower runoff depth and higher soil loss rate. Rainfall regime B with longer RD, and higher P and Im, however, produced higher rainfall depth and lower soil loss rate. Terraced plot had the highest runoff and soil loss reduction efficiencies of over 96.03%. Contour tillage had comparable sediment reduction efficiency to that of the terraced plot on gentle slopes (gradient less than 11.0%), while its runoff reduction efficiency was less than 13.11%. This study implies that in the Miyun Reservoir catchment and similar regions in the world, contour tillage should be promoted on gentle slopes, and terrace construction should be given enough attention since it can greatly reduce water quantity and cause water shortage in downstream catchments.

This paper offers a comprehensive examination of the process involved in developing and automating supervised end-to-end machine learning workflows for forecasting and classification purposes. It offers a complete overview of the components (i.e. feature engineering, model selection, etc), principles (i.e. bias-variance decomposition, model complexity, overfitting, model sensitivity to feature assumptions and scaling, output interpretability, etc), models (i.e. neural networks, regression models, etc), methods (i.e. Cross-Validation, data augmentation, etc), metrics (i.e. Mean Squared Error, F1-score, etc) and tools that rule most supervised learning applications with numerical and categorical data, as well as their integration, automation, and deployment. The end goal and contribution of this paper is the education and guidance of the non-AI expert academic community over complete and rigorous machine learning pipelines and data science practices, from problem scoping to design and state-of-the-art automation tools, including basic principles and reasoning in the choice of methods. The paper delves into the critical stages of supervised machine learning workflow development, many of which are often omitted by researchers due to brevity, and covers foundational concepts essential for understanding and optimizing a functional machine learning workflow, thereby offering a holistic view of task-specific application development for applied researchers who are not AI experts.

There is a great interest in finding antioxidants and products with antimicrobial activities from natural sources. The aim of this study was to obtain and identify the phenolic components and organic acids from Camellia oleifera cake. In addition, their antioxidant and antimicrobial activities were also investigated. The purity of phenolic components and organic acids obtained were 94.1 ± 0.5% w/w and 96.0 ± 0.3% w/w, respectively. There are 15 phenolic components have been detected and identified by HPLC-ESI-MS. Oxalic, citric, acetic, malic, and succinic acids are found to be major organic acids. The phenolic components and organic acids both had good antioxidant capacity, evaluated by 4 antioxidant activity assays (hydroxyl radical scavenging, superoxide radical scavenging, 1,1-diphenyl-2-picryl-hydrazyl radical scavenging and lipid peroxidation inhibition). In addition, the phenolic components and organic acids exhibited significant inhibitory activity against bacteria Staphylococcus aureus, Escherichia coli, Bacillus subtilis, and fungi Mucor racemosus, Aspergillus oryzae, Rhizopus stolonifer. The phenolic components and organic acids from C. oleifera cake both showed good antioxidant capacity and exhibited antimicrobial activities. These results may be useful for the future use of phenolic components and organic acids from C. oleifera cake.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

Through the ACE2, a main enzyme of the renin-angiotensin system (RAS), the SARS-CoV2 gains access into the cell, resulting in different complications which may extend beyond the RAS and impact the Arachidonic Acid (ArA) pathway. The contribution of the RAS through ArA pathways metabolites in the pathogenesis of COVID-19 is unknown. We investigated whether RAS components and ArA metabolites can be considered biomarkers of COVID-19. We measured the plasma levels of RAS and ArA metabolites using an LC-MS/MS. Results indicate that Ang1-7 levels were significantly lower, whereas Ang II levels were higher in the COVID-19 patients than healthy control individuals. The ratio of Ang1-7/Ang II as an indicator of the RAS classical and protective arms balance was dramatically lower in COVID-19 patients. There was no significant increase in inflammatory 19-HETE and 20-HETE lev-els. The concentration of EETs was significantly increased in COVID-19 patients, whereas the DHETs concentration was repressed. Their plasma levels were correlated with Ang II concentration in COVID-19 patients. In conclusion, evaluating the RAS and ArA pathway biomarkers could provide helpful information for the early detection of high-risk groups, avoid delayed medical attention, facilitate resource allocation and improve patient clinical outcomes to prevent long COVID incidence.

The paper is a follow-up of a previous investigation and effort to develop the ontology of the smart city (Komninos, N., Bratsas, C., Kakderi, C., and Tsarchopoulos, P. "Smart city ontologies: Improving the effectiveness of smart city applications". Journal of Smart Cities, vol. 1(1), 1-17. https://www.komninos.eu/wp-content/uploads/2015/07/2015-Smart-City-Ontologies-Published.pdf). Since the publication of this article in 2015, research and literature on smart cities have evolved significantly, as have the technologies for digital spaces and applications that support city functions. These developments are reflected in the present form of the smart city ontology 2.0 we propose. It depicts the building blocks of the smart city ontology (technologies, structure, function, planning), and the object properties and data properties that connect structural blocks and classes. The aim of the SCO 2.0 is to provide a better understanding and description of the smart/intelligent city landscape; identify the main components and processes, the terms used to describe them, their definition and meaning; clarify key processes related to the integration of the different dimensions of the smart city, mainly the physical, social, and digital dimensions. The paper is accompanied by an owl file, developing the ontology through the editor Protégé.

Coronavirus disease 2019 (COVID-19) is a global pandemic caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). To contain the virus, numerous preventive measures have been taken including isolation of patients, careful infection control, social distancing, and taking vaccine. So far, new confirmed and death cases are still increasing. SARS-CoV-2 invades cells by using the angiotensin converting enzyme 2 (ACE2). ACE2 is an essential enzyme of the renin-angiotensin system (RAS) which converts angiotensin II (Ang II) to angiotensin (1-7). ACE2 is expressed in different organs, including lung, heart, and kidney. A high number of COVID-19 patients developed kidney injury has been reported. Renal impairment and acute injury are associated with mortality of COVID-19, which is 14-16 times higher than other general patients. Acute Kidney Injury has been occured in 2.9 up to 43% of intensive care unit patients. The increasing evidence show that the components of RAS can activate the complement cascade, and cytokines production. Kidney injury caused by SARS-CoV-2 is related mainly to systemic and local inflammation. Moreover, the uncontrolled immune responses mediated by SARS-CoV-2 including hypercytokinaemia, secondary hemophagocytic lymphohistiocytosis, antibody dependent enhancement, complement system, and phagocytic cells activation can contribute in the virus pathogenesis leading to associated renal dysfunction. However, the role and crosstalk between of RAS components and immune response in mediating kidney injury remain undefined. In this review, we focus on the recent studies to provide the pathogenesis of SARS-CoV-2 interacting with RAS and immune responses to mediate kidney injury.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

Regular inspections during construction work verify that the work completed is consistent with the plans and specifications and ensure that it is within the planned time and budget. This requires frequent physical site observations to independently measure and verify the completion percentage of the construction progress performed over periods of time. The current computer vision-based (CV) techniques for the measurement of as-built elements, predominantly use 3D laser scanning or 3D Photogrammetry modelling to determine the geometrical properties of as-built elements on construction sites. Both techniques require data acquisition from several positions and angles to generate sufficient information about the element’s coordinates making the deployment of these techniques on dynamic construction project sites a challenging task. In this paper, we propose a pipeline for automating the measurement of as-built components using artificial intelligence (AI) and computer vision (CV) techniques. The pipeline requires a single image obtained with a stereo-camera system to measure the size of selected objects or as-built components. We demonstrate our approach by measuring the size of concrete walls and columns. The novelty of this work is attributed to the fully automated CV-based method for measuring any given element using a single image only. The proposed solution is suitable for use in measuring the sizes of as-built components of built assets. It has the potential to be further developed and integrated with BIM models for use on construction projects for progress monitoring.

Coffee is not only a delicious beverage but also an important dietary source of natural antioxidants. We live in an oxidative world where it is impossible to avoid pollution, stress, food additives, radiation, and other sources of oxidants that eventually lead to severe health disorders. Fortunately, there are chemicals in our diet that counteract the hazards posed by the reactive species that trigger oxidative stress. They are usually referred to as antioxidants; some of them can be versatile compounds that exert such a role in various ways. This review summarizes, from a chemical point of view, the antioxidant effects of relevant molecules found in coffee. Their ways of action and trends in activity are analyzed, considering the data gathered so far from both theory and experiments. The influence of the media and pH in aqueous solution, and structure-activity relationships are discussed. The protective role of the explored compounds is examined. A particular section is devoted to derivatives of some coffee components, and another one to their bioactivity. The data used in the analysis come from theoretical anc computational protocols, which have been proven to be very usefull in this context. Hopefully, the information provided here will promote further investigations into the amazing chemistry contained in our morning cup.

Coffee is not only a delicious beverage but also an important dietary source of natural antioxidants. We live in an oxidative world where it is impossible to avoid pollution, stress, food additives, radiation, and other sources of oxidants that eventually lead to severe health disorders. Fortunately, there are chemicals in our diet that counteract the hazards posed by the reactive species that trigger oxidative stress. They are usually referred to as antioxidants; some of them can be versatile compounds that exert such a role in various ways. This review summarizes, from a chemical point of view, the antioxidant effects of relevant molecules found in coffee. Their ways of action and trends in activity are analyzed, considering the data gathered so far from both theory and experiments. The influence of the media and pH in aqueous solution, and structure-activity relationships are discussed. The protective role of the explored compounds is examined. A particular section is devoted to derivatives of some coffee components, and another one to their bioactivity. Hopefully, the information provided here will promote further investigations into the amazing chemistry contained in our morning cup.

Work from the last years indicate that the extracellular matrix (ECM) plays a direct role in vari-ous cellular processes including proliferation, migration and differentiation. Besides homeostat-ic processes, its regulatory function in inflammation becomes more and more evident. In in-flammation like inflammatory bowel disease, the ECM composition is constantly remodeled which can result in a structuring of fistulizing disease course. Thus, tracking early ECM changes might bear the potential to predict the disease course. In this review, we will provide an over-view of relevant diagnostic methods focusing on ECM changes.

The use of principal components analysis provided information about the main characteristics of teams, based on a set of indicators, instead of displaying individualized information for each of these indicators. In this work we have considered reducing an extensive data matrix to improve interpretation, using the principal components analysis. Subsequently, with new components and with a multiple linear regression, we have carried out a comparative analysis between the best and bottom teams of LaLiga. The sample consisted of the matches corresponding to the 2015/16, 2016/17 and 2017/18 seasons. The results showed that the best teams were characterized and differentiated from bottom teams in the realization of a greater number of successful passes and in the execution of a greater number of dynamic offensive transitions. The bottom teams were characterized by executing more defensive than offensive actions and showing a fewer number of goals, a greater ball possession time in the final third of the field. Goals, ball possession time in the final third of the field, number of effective shots and crosses are the main performance factors that influence the offensive success of football. This information allows us to increase knowledge about the key performance indicators in football.

Driven by environmental sustainability concerns, the integration of biobased components in curtain wall systems is gaining traction in both research and the construction market. This paper explores the development and validation of a bio-based façade system within the Basajaun H2020 project. The project aimed to demonstrate the feasibility of introducing environmentally friendly bio-based components into the mature curtain wall façade industry. The paper focuses on identifying technological solutions for replacing key components such as profiles, insulation, and the tightness system with bio-based and less environmental impact alternatives presenting the results achieved in the façade system design of the Basajaun project funded by European Union. These solutions aimed at creating a bio-composite-based curtain wall façade that adheres to current building envelope standards and normative; to implement diverse façade typologies for vision panels, opaque sections, and integrated windows; to engineer the prefabrication process for industrialization, enabling wider market replication and simplified transport and installation. The results demonstrate that the Basajaun façade successfully integrates selected components and meets the performance requirements set by regulations. However, questions remain regarding the workability of bio-based profiles as a commercially viable, ready-to-market solution that can replace traditional aluminum profiles in the curtain wall façade industry.

Work on callings has burgeoned in the past 20 years, yet recent reviews exposed a lack of conceptual clarity and disagreements around its definition, components and measures. One lingering point of contention revolves around the element of prosociality: Is a calling orientation primarily motivated by self-interest, prosocially orientated, or a mix of both? This conceptual paper reviews and examines the pro-self and prosocial component of a calling outlook, by examining and comparing the ways in which they feature in different calling subtypes: Classic, neoclassic, and modern callings. Our analysis suggests that these subtypes vary in where they are located on a pro-self – prosocial continuum: Classic callings are located on the prosocial side of the axis, modern callings are located on pro-self side of the axis, and neoclassic callings can be situated in the middle of the con-tinuum, integrating self-orientated and other-orientated motivations. Our analysis further suggests that these calling subtypes draw on divergent value systems: Classic callings are propelled by self-transcendent values, modern callings are driven by self-actualization motivations, and neoclassic callings integrate both value systems. We therefore argue that the subjective experiences of pursuing a calling within each subtype pathway differ, alt-hough they may culminate in similar outcomes. The paper offers a novel framework for analyzing people’s calling that draws on their values.

The phycobilisome (PBS) is the major light-harvesting apparatus in cyanobacteria and red algae, a large multi-subunit protein complex of several megadaltons that is found on the stromal side of thylakoid membranes in orderly arrays. Chromophore lyases catalyse the thioether bond between apoproteins and phycobilins of PBSs. Depending on the species, composition, spatial assembly and, especially, the functional tuning of different phycobiliproteins mediated by linker proteins, PBSs can absorb light between 450 and 650 nm, making them efficient and versatile light-harvesting systems. However, basic research and technological innovations are needed, not only to understand their role in photosynthesis but also to realise the potential applications of PBSs. Synthetic biology provides an innovative approach to expand our understanding of the distinctive properties that make the PBS such an efficient light-harvesting system and to explore its heterologous synthesis, photosynthetic functions and potential medical applications. Focusing on these topics, this review describes the essential components needed for PBS assembly, the functional basis of PBS photosynthesis and the applications of phycobiliproteins. Moreover, key technical challenges for heterologous biosynthesis of phycobiliproteins in chassis cells are discussed.

The tissue micro environment or milieu consists of a highly dynamic population of cellular and non-cellular components which constitute a complex regulatory network aimed at maintaining the organ homeostasis. In the modern medicine the discovery of miRNAs is undoubtedly a promising field of research and they are essential in orchestrating immune system logic and their release in the gut micro milieu can directly affect bacterial gene expression. Here, we briefly review the role of microRNAs, focuses on their role on immune system components in physiological and pathophysiological gut micro milieu.

Supramolecular solvent (SUPRAS) has received increasing interest as an innovative, efficient, and green solvent for the effective extraction and separation of bioactive compounds from natural resources. However, studies on the use of SUPRAS for the extraction of phenolic components from plants, which are highly valued in food products due to their excellent antioxidant capacity, are still lacking. The present study developed a green ultrasound-assisted and efficient SU-PRAS method to simultaneously determine three phenolic acids in Prunella vulgaris by high-performance liquid chromatography (HPLC) and the experimental parameters were optimized in detail. The efficiency and antioxidant properties of the phenolic compounds obtained by different extraction methods were also compared. Under the optimal conditions, the extraction efficiency of SUPRAS, prepared with octanoic acid reverse micelles dispersed in ethanol-water, was substantially higher than conventional organic reagents. Moreover, this SUPRAS method also showed more significant antioxidant capacities. The confocal laser scanning microscopy (CLSM) images presented the spherical droplet structure of SUPRAS (A well-defined circle), which coincided with the position of the fluorescence position of phenolic acids. The phenolic acids were encapsulated in the vesicles by the SUPRAS droplets, which indicated the efficient extraction capacities of SUPRAS for the target compounds. Finally, combined with the CLSM method, the mechanism of the proposed method was further clarified, and the superior extraction performance of SUPRAS was theoretically demonstrated through molecular dynamics simulations. In comparison with conventional methods, the higher extraction efficiency of SUPRAS can be illustrated by the larger solvent contact surface area, more types of hydrogen bonds between extractants and supramolecular solvents, and stronger and more stable interaction forces. The results of the theoretical studies are in rational agreement with the experimental outcome.

Machine learning (ML) is growing in popularity for various particle accelerator applications including anomaly detection such as faulty beam position monitor or RF fault identification, for non-invasive diagnostics, and for creating surrogate models. ML methods such as neural networks (NN) are useful because they can learn input-output relationships in large complex systems based on large data sets. Once they are trained, methods such as NNs give instant predictions of complex phenomenon, which makes their use as surrogate models especially appealing for speeding up large parameter space searches which otherwise require computationally expensive simulations. However, quickly time varying systems are challenging for ML-based approaches because the actual system dynamics quickly drifts away from the description provided by any fixed data set, degrading the predictive power of any ML method, and limits their applicability for real time feedback control of quickly time-varying accelerator components and beams. In contrast to ML methods, adaptive model-independent feedback algorithms are by design robust to un-modeled changes and disturbances in dynamic systems, but are usually local in nature and susceptible to local extrema. In this work, we propose that the combination of adaptive feedback and machine learning, adaptive machine learning (AML), is a way to combine the global feature learning power of ML methods such as deep neural networks with the robustness of model-independent control. We present an overview of several ML and adaptive control methods, their strengths and limitations, and an overview of AML approaches. A simple code for the adaptive control algorithm used here can be downloaded from: https://github.com/alexscheinker/ES_adaptive_optimization

The soybean aphid (SBA; Aphis glycines Matsumura) and the soybean cyst nematode (SCN; Heterodera glycines Ichninohe) are major pests of the soybean (Glycine max (L.) Merr.). Independent studies on these pests have made substantial progress in understanding the genetic basis of limiting these pests in both model and non-model plant systems. Classical linkage mapping and genome-wide association studies (GWAS) have identified some major and minor QTLs in soybean. The studies on interactions of aphid and nematode effectors with host proteins allow us to identify molecular cues in various signaling components, including plant disease resistance and phytohormone genes. Here we review various resistance components of both SBA and SCN in terms of their effectors, their role in eliciting or attenuating host defense and update on findings on key quantitative trait loci (QTLs)/genes in soybean that could help in mitigating these widespread shifted virulent soybean aphid and SCN populations. We also provide an update on recent interaction studies of soybean-soybean aphid-SCN as well as interaction studies involving different aphids/nematodes and their host systems. PHYTOALEXIN DEFICIENT4 (PAD4) in soybean could possibly play a major role in providing resistance against both soybean aphid and SCN.

Considering the manufacturing of automotive components, there exists a dilemma around the substitution of traditional Cast Iron (CI) with lighter metals. Nowadays, aluminium alloys, being lighter compared to traditional materials, are considered as a more environmentally friendly solution. However, the energy required for the extraction of the primary materials and manufacturing of components is usually not taken into account in this debate. In this study, an extensive literature review has been performed to estimate the overall energy required for the manufacturing of an engine cylinder block using (a) cast iron and (b) aluminium alloys. Moreover, data from over 100 automotive companies, ranging from mining companies to consultancy firms, have been collected in order to support the soundness of this investigation. The environmental impact of the manufacturing of engine blocks made of these materials is presented with respect to the energy burden; the “cradle-to-grave approach” has been implemented to take into account the energy input of each stage of the component lifecycle starting from the resource extraction and reaching to the end-of-life processing stage. Our results indicate that although aluminium components contribute towards reduced fuel consumption during their use phase, the vehicle distance needed to be covered in order to compensate for the up-front energy consumption related to the primary material production and manufacturing phases is very high. Thus, the substitution of traditional materials with lightweight ones in the automotive industry should be very thoughtfully evaluated.

The primary aim of this study is to investigate the relationship of the Mediterranean diet (MD) with metabolic syndrome (MetS) and its components in Caucasian subjects between 35 and 74 years. The secondary aim is to analyze sex differences. Methods: A cross‑sectional trial. This study utilized data from the EVA, MARK, and EVIDENT studies, a total of 3417 subjects with a mean age of 60.14±9.14 years (57% men). MetS was defined based on the Joint Scientific Statement National Cholesterol Education Program III. Waist circumference, blood pressure, fasting plasma glucose, and lipid profile were measured. Adherence to the MD was assessed with the 14-item Mediterranean Diet Adherence Screener (MEDAS) questionnaire used in the PREDIMED study. Good adherence was considered when the MD value was higher than the median value. Results: The mean value of the MEDAS questionnaire was 5.83±2.04; (Men 5.66±2.06 and women 6.04±1.99; p&lt;0.001). Adherence to the MD was observed by 38.6% (34.3% men and 40.3% women; p&lt;0.001). MetS was observed in 41.6% (39.0% men and 45.2%women p&lt;0.001). In the multiple regression analysis after adjusting for possible confounders, the mean MD value showed a negative association with the number of MetS components per subject (β=-0.336), and with the different components of MetS: Systolic blood pressure (β=-0.011), Diastolic blood pressure (β=-0.029), glycemia (β=-0.009), Triglycerides (β=-0.004), Waist circumference (β=-0.026), except with the HDL-cholesterol value which showed a positive association (β=0.021); (p&lt;0.001 in all cases). The adjusted logistic regression models showed that an increase in MDA decreases the probability of MetS (OR =0.56) and its components: blood pressure ≥130/85 mmHg (OR = 0.63), fasting plasma glucose ≥100 mg/dL (OR = 0.62); triglycerides ≥150 mg/dL (OR = 0.65); waist circumference ≥88 cm in women and ≥102 cm in men (OR = 0.74), and increases high-density lipoprotein cholesterol &lt;40 mg/dL in men or &lt;50 mg/dL in women (OR = 1.70); (p&lt;0.001 in all cases). The results by sex were similar, both in multiple regression and logistic regression. Conclusion: The results of this study suggest that a greater adherence to the Mediterranean diet decreases the probability of presenting Mets globally and by sex.

Although Lov\'{a}sz introduced the graph exponential $G^K$ in 1967, this product has received little attention. This paper focuses on the number of components in $G^K$ when exponent $K$ is a complete graph $K_n$. For a connected bipartite $G$, when $K$ is $K_2$, $G^{K_2}$ has three components; and when $K$ is $K_n$ with $n>2$, $G^{K_n}$ produces $\lceil\frac{n+1}{2}\rceil$ components. A connected $G$ with an odd cycle produces one component in $G^{K_n}$.

With demand for the long-term continued use of existing building facilities, structural health monitoring and damage detection are attracting interest from society. Sensors of various types have been practically applied in the industry to satisfy this need. Among the sensors, piezoelectric sensors are an extremely promising technology by virtue of their cost advantages and durability. Although they have been used in aerospace and civil engineering, their application for building engineering remains limited. Remarkably, recent catastrophic seismic events have further rein-forced the necessity of rapid damage detection and quick judgment about the safe use of facilities. Faced with these circumstances, this study was conducted to assess the applicability of piezoelectric sensors to evaluate building components. Specifically, this study emphasizes structural damage caused by earthquakes. After first applying to cyclic loading tests to composite beam component specimens and steel frame subassemblies with a folded roof plate, the prospective damage posi-tions were also found using finite element analysis. Crack propagation and buckling locations were predicted adequately. The piezoelectric sensors provided output when the concrete slab showed tensile cracks, or when the folded roof plate experienced local buckling. Furthermore, damage expansion and progression were detected multiple times during loading tests. Results showed that the piezoelectric sensors can detect structural damage of building components, demonstrating their potential for use in inexpensive and stable monitoring systems.

In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.

Wind power is one of the most important sources of renewable energy available today. A large part of the wind energy cost is due to the cost of maintaining wind power equipment. When a wind turbine component fails to function, it might need to be replaced under the less than ideal circumstances. This is known as corrective maintenance. To minimize unnecessary costs, a more active maintenance policy based on the life expectancy of the key components is preferred. Optimal scheduling of preventive maintenance activities requires advanced mathematical modeling. In this paper, an optimal preventive maintenance algorithm is designed using the renewal-reward theorem. In the multi-component setting, our approach involves a new idea of virtual maintenance which allows us to treat each replacement event as a renewal event even if some components are not replaced by new ones. The proposed optimization algorithm is applied to a four-component model of a wind turbine and the optimal maintenance plans are computed for various initial conditions. The modeling results showed clearly the benefit of PM planning compared to pure CM strategy (about 30% lower maintenance cost).

The aim of the presents study is to further expand the model of translational cross-validation by investigating the brain circuits or networks which underpin the same tasks by means of group independent component analysis for FMRI toolbox (GIFT). We hypothesized that there will be neural network patterns of activation and deactivation, which correspond to real time performance on clinical self-evaluation scales. We recruited 42 subjects: 20 healthy controls and 22 patients with major depressive episode. All subjects underwent functional MRI scanning using paradigm comprised of diagnostic clinical self-assessment depression scale contrasted to neutral scale. The data were processed with group independent component analysis for functional MRI toolbox and statistical parametric mapping. The results have demonstrated that there exist positively or negatively modulated brain networks during processing of diagnostic specific task questions for major depressive disorder. There have also been confirmed differences in the networks processing diagnostic versus off blocks between patients and controls in anterior cingulate cortex and middle frontal gyrus. Diagnostic conditions (depression scale) when contrasted to neutral conditions demonstrate differential activity of right superior frontal gyrus and right middle cingulate cortex in the comparison of patients with healthy controls. It is for the first time when potential neuroimaging state dependent biomarker has been directly linked with clinical assessment self-evaluation scale, administered as stimuli simultaneously with the fMRI acquisition. It may be regarded as further evidence in support of the ability of both methods to concordantly distinguish groups by means of incremental translational cross-validation.

The specificity and potency of venom components gives them a unique advantage in development of various pharmaceutical drugs. Though venom is a cocktail of proteins rarely is the synergy and association between various venom components studied. Understanding the relationship between various components is critical in medical research. Using meta-analysis, we found underlying patterns and associations in the appearance of the toxin families. For Crotalus, Dis has the most associations with the following toxins: PDE; BPP; CRL; CRiSP; LAAO; SVMP P-I &amp; LAAO; SVMP P-III and LAAO. In Sistrurus venom CTL and NGF had most associations. These associations can be used to predict presence of proteins in novel venom and to understand synergies between venom components for enhanced bioactivity. Using this approach, the need to revisit classification of proteins as major components or minor components is highlighted. The revised classification of venom components needs to be based on ubiquity, bioactivity, number of associations and synergies. The revised classification will help in increased research on venom components such as NGF which have high medical importance.

Diabetes mellitus (DM) is a metabolic disorder characterized by the deficiency of insulin production and is one of the concerning health problems worldwide, especially in developing countries. Considering the systemic toxicity associated with current antidiabetic medications and their limited efficacy, there is an urgent need to discover new plant-based natural antidiabetics. Since time immemorial, medicinal plants have played an important role in the management of health disorders. In recent years, herbal medicine has experienced exponential growth in popularity worldwide, owing to its natural origin and fewer side effects, appealing to both developing and developed nations. Ecuador has a rich cultural history in ethnobotany that plays a crucial role in their people's lives. Several Ecuadorian medicinal plants have hypoglycemic or an-ti-hyperglycemic properties that are rich with bioactive phytochemicals. These medicinal plants were extensively used in traditional medicine preparation in Ecuador for many decades to treat diabetes because of their cost-effectiveness, available traditional knowledge, and low toxicity. Many Ecuadorian medicinal plants are reported to have antidiabetic properties that reduce blood sugar levels, and oxidative stress, regulate intestinal function, improve insulin resistance, inhibit α-amylase and α-glucosidase, lower gluconeogenic enzymes, stimulate glucose uptake mechanisms, and play an important role in glucose and lipid metabolism, yet there is a substantial lack of integrated approach between the existing ethnomedicinal practice and pharmacological research. Therefore, this review aims to discuss and explore the traditional medicinal plants used in Ecuador for treating DM and their bioactive phytochemicals, which are mainly responsible for their anti-diabetic properties.

This study innovatively assesses the Mun River flow components in Thailand, integrating Artificial Neural Networks (ANN) and Isotopic (18O) End-Member Mixing Analysis (IEMMA). It quantifies the contributions of the Upper Mun River (UMR) and Chi River (CR) to the overall flow, revealing a discrepancy in their estimated contributions. ANN predicts the UMR and CR contribute approximately 70.1% and 29.5% respectively, while IEMMA indicates a more pronounced disparity with 84% from UMR and 16% from CR. This divergence highlights the distinct perspectives of ANN, focusing on hydrological data patterns, and IEMMA, emphasizing isotopic signatures. Despite discrepancies, both methods validate UMR as a significant contributor to the overall flow, highlighting their utility in hydrological research. The findings underscore the complexity of river systems and advocate for an integrated approach of river flow analysis for a comprehensive understanding, crucial for effective water resource management and planning.

A rapid and appropriate genetic and metabolic acclimation, which is crucial for plants’ survival in a changing environment, is maintained due to the coordinated action of plant hormones and cellular degradation mechanisms influencing proteostasis. The plant hormone abscisic acid (ABA) rapidly accumulates in plants in response to environmental stress and plays a pivotal role in the reaction to various stimuli. Increasing evidence demonstrates a significant role of autophagy in controlling ABA signaling. This field has been extensively investigated and new discoveries are constantly being provided. We present updated information on the components of the ABA signaling pathway, particularly on transcription factors modified by different E3 ligases. Then, we focus on the role of selective autophagy in ABA pathway control and review novel evidence on the involvement of autophagy in different parts of the ABA signaling pathway that are important for crosstalk with other hormones, particularly cytokinins and brassinosteroids.

The influence of pore size on the toughness of Fe-Mo-Cu-C sintered and carburized components was investigated. The charpy impact value of the component made from Fe-0.4%Mo diffusion-alloyed steel powder mixed with 2%Cu powder and 0.3% graphite powder significantly increased with a decrease in pore size. The highest impact value of 17 J/cm2 was obtained at the average pore size of 12 µm. This value was 25% higher than that of the sintered and carburized component made from conventional Fe- 4%Ni-1.5%Cu-0.5%Mo alloyed steel powder called 4Ni even though the component was made from a Ni-free alloyed steel powder. The mechanism of the improvement of the impact value by pore size refinement and the influence of microstructural difference between the components made from Fe- 0.4%Mo diffusion-alloyed steel powder and 4Ni on toughness is discussed based on optical microstructural observation and crystal orientation analysis data.

Plant-based alternative medicine is normally grounded on empiric cultural perception, as the main objective, these practices intent to either maintain good health or to provide a route to turn-the-tide on a specific disease or ailment. Amongst the thousands of plants that have been used and studied, Neem (Azadirachta indica) seems to have a very interesting tale to tell, since its properties to ward-off certain diseases have overtime, and in a rigorous way, been proven. The preceding concise review is a collection of some of the most relevant studies today, not only focusing on the health benefits obtained by its use, but digging into the molecular mechanisms of how the properties come about. In particular, we take a look over antioxidant properties and how these mediate and mitigate important molecules such as IL-6 and TNF-, leading the way in reducing systematic damage by oxidative stress. Further, we relate this oxidative reduction to other systemic diseases such as cancer and diabetes, as these are currently becoming the most rampant killers. As of yet not all is known about the different ways of extracting or the total composition of an extract, as these may be from different parts of the plant. Therefore, we also allude to an important cautionary view where toxicological effects and conflicting outcomes arise. Overall, presented results show a great potential for the different extracts of Neem as their antioxidant activity can be taken advantage off, and potentially used in modern medicine.

Milk is a complex liquid, and the concentrations of many of its components are under genetic control. Many genes and pathways are known to regulate milk compositon, and the purpose of this review is to highlight how the discoveries of quantitative trait loci (QTL) for milk phenotypes can elucidate these pathways. The main body of this review focusses primarily on QTL discovered in cattle (Bos taurus) as a model species for lactation biology, with occasional references to other ruminant species, and some comparisons with human milk composition are also presented. The following section describes a range of techniques that can be used to help identify the causative genes underlying QTL when the underlying mechanism involves the regulation of gene expression. As genotype and phenotype data bases continue to grow and diversify, new QTL will continue to be discovered, and, although proving the causality of underlying genes and variants remains difficult, these new data sets will further enhance our understanding of lactation biology.

All over the world birds’ eggs are an important and valuable component of the human diet. The study aimed to compare the content of lipid components and their nutritional value as well as iron and zinc levels in chicken and quail eggs commonly available on the market. In egg lipids, unsaturated acids were dominated, especially oleic acid, the content of which was about 40% of total fatty acids (TFA). Linoleic acid was the major polyunsaturated fatty acid. Compared to other products of animal origin, eggs were characterized by favourable values of lipid quality indices, especially index of atherogenicity, thrombogenicity and hypocholesterolemic to hypercholesterolemic ratio. In the present study, no differences in the content of tested nutrients between eggs from different production methods (organic, free-range, barn, cages), as well as inter-breed differences were noticed. Cluster analysis showed that eggs enriched in n3 PUFA (according to producers’ declaration) differ from other groups of chicken eggs. However, only in eggs from one producer, the amount of EPA and DHA exceed 80 mg per 100 g, entitling to use the nutrition claim on the package. Quail eggs differed from chicken eggs in FA profile; they also had much higher iron and cholesterol levels.