One of the primary causes of the mechanical seal failure is rotor vibration. Traditional dynamic seal models often would not be able to fully explaining the failure mechanisms. The seal dynamic models proposed in this paper, including those developed by the authors, prove valuable in predicting seal dynamics during operation in specific turbomachinery and in explaining the causes of seal failure. The single-mass dynamic model is suitable for analyzing contact mechanical seal and simple design dry gas seals dynamics. The two-mass dynamic model is used for investigating operational dynamics processes in classical dry gas seals under complex loading conditions. The three-mass dynamic model is used to study various complex mechanical seal types. This model is able to determine the normal operating condition range and to explain leakage mechanisms in the presence of excessive rotor vibrations.

Conventional traceability systems in Cambodian agriculture, such as Rubber Supply Chain Management (RSCM), often struggle to provide timely data and fair market prices, leading to mistrust among stakeholders, exploitation by intermediaries, and hindering progress towards ethical sourcing and sustainable practices. This research aims to showcase the potential of integrating blockchain technology, the Internet of Things (IoT), the InterPlanetary File System (IPFS), and Differential Privacy (DP) methods to empower Cambodian rubber farmers. By enhancing transparency, facilitating fair pricing, and promoting sustainable methods in the rubber industry, this integrated approach leverages Hyperledger Fabric (HLF) to create a decentralized and secure system for tracking rubber from its source to the end consumer. Integration with IPFS ensures secure and easily accessible data storage, further enhancing the system’s reliability. Additionally, the implementation of differential privacy techniques safeguards confidential data during information sharing among farmers and supply chain stakeholders, minimizing potential privacy concerns. This comprehensive system encourages consumers to make ethical and sustainable alternative options by providing accessible information on harvesting methods, processing procedures, labor conditions, and environmental impacts. The potential benefits extend beyond Cambodia, serving as a model for other developing countries aiming to modernize and enhance the agricultural distribution networks. Our results show that transaction send rates (TPS) and throughput in systems with and without differential privacy grow with increased transaction volumes. However, the system without differential privacy achieves greater scalability and efficiency above a certain threshold. However, it offers a slightly reduced latency, reflecting a trade-off between privacy and performance efficiency in blockchain-based agricultural traceability systems.

Farm activities continued sand winning operations and the allocation of plots of land to prospective developers in Ghana pose a serious threat to the forest covers and lifespan of the Forest and game reserves. With all the positive add ups to the country from forests, Ghana has lost more than 33.7%(equivalent to 2,500,000 hectares) of its forest, since the early 1990s between 2005 and 2010, the rate of deforestation in Ghana was estimated at 2.19% per annum; the sixth highest deforestation rate globally for that period. This shows how important forest monitoring can be to the forestry commission in Ghana. Despite the frameworks which have been developed to help Ghana to protect and restore its forest resources, inadequate monitoring systems remain a barrier to effective implementation. In this study, Google earth engine was used to map and analyze the structural changes of forest cover using JavaScript to query and compute Landsat, MODIS and NOAA AVHRR satellite imageries of the study area (Ghana) with spatial resolutions 30m, 250m and 7km respectively. A supervised classification was performed on three multi-temporal satellite imageries and a total of six major land use and land cover classes were identified and mapped. By using random Forest-classification technique, from 1985 to 2018 recorded by NOAA AVHRR, forest cover has decreased by 66% and 2000 to 2018 recorded by Landsat and MODIS 61% and 47% respectively. A decrease in the forest has been as a result of anthropogenic activities in Ghana. A change detection analysis was performed on these images and it was noted that Ghana is losing forest reserves in every 5years. Overlay of the reserved forest of the 2000 and the classified map of 2018 shows vegetation changed during 2000-2018 remarkably. Therefore, forest-related institutions like the Forestry Commission can employ and use this monitoring system on Google Earth Engine for processing satellite images particularly Landsat, MODIS and NOAA AVHRR for forest cover monitoring and analysis for fast, efficient and reliable results.

(S)-Atenolol ((S)-2-(4-(2-Hydroxy-3-(isopropylamino)propoxy)phenyl)acetamide) has been synthesized in >99% ee with use of Candida antarctica lipase B from Syncozymes (Shanghai, China), in a kinetic resolution of the corresponding racemic chlorohydrin. Deprotonation of the starting phenol building block was base catalyzed. The enantiopurity of the chlorohydrin building block remained unchanged upon subsequent amination. All four steps in the synthesis protocol have been optimized compared to previously reported methods, which makes this new protocol more sustainable and in accordance with green chemistry principles compared to previously reported protocols.

The present study examines the effect of SiO2 nano-additives on the performance and emission characteristics of a diesel engine fuelled with soybean biodiesel. Soybean biofuel was prepared using the transesterification process. Nano-additives characterisations were done using different tests such as FESEM, XRD, EDS, etc., to study the morphology of nano-additives. For proper blending of nano-additives with biodiesel, the ultrasonication process was used. Surfactant was used for the stabilisation of nano-additives. After making all the combinations of nano fuel blends, physicochemical properties were measured as per ASTM standards. Performance and emissions readings were taken at different load conditions. It was found that with the addition of SiO2 nano-additives, brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) was increased by 3.48-6.39% and 5.81-9.88%, respectively. Significant reduction of CO, CO2, NOx, and smoke emissions were also observed compared to baseline fule due to better combustion efficiency with the use of SiO2 nano-additive.

Spray penetration into citrus canopies is critical for adequate coverage and deposition to ensure effective pest control. However, mismatch of air assistance to target canopy characteristics can lead to unintended spray loss through over penetration. To evaluate the effect of air assistance on on-target deposition, two sprayers (surrogates for airflow rates) were used to apply a fluorescent tracer dye solution @ target concentration of 300 ppm to 16 medium foliage density tree blocks in a commercial mandarin orchard. The complete factorial experiment in three replications comprised two ground speeds (1.6 and 4.8 km/h), two disc-core nozzles (TeeJet® D3-25 and D6-45), and either one or two nozzle rows to obtain a wide range of application rates (496 to 9,719 L/ha). Dye deposition significantly decreased with canopy depth (p=<0.001) by nearly 7 times across the 3.4-m-wide canopies but was not significant over 1.2 to 2.2 m sampling height (p=0.867). Deposition obtained with the low airflow rate sprayer was significantly greater (p=<0.001) than that obtained with the high airflow rate sprayer over the dose range likely due to too much air pushing out spray droplets. This study underscores the importance of matching the air assistance of orchard sprayers to the target canopy.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

In this paper, we present a new concept of the generalized core orthogonality (called the C-S orthogonality) for two generalized core invertible matrices $A$ and $B$. $A$ is said to be C-S orthogonal to $B$ if $A^{\tiny\textcircled{S}}B=0$ and $BA^{\tiny\textcircled{S}}=0$, where $A^{\tiny\textcircled{S}}$ is the generalized core inverse of $A$. The characterizations of C-S orthogonal matries and the C-S additivity are also provided. And the connection between the C-S orthogonality and C-S partial order has been given using their canonical form. Moreover, the concept of the strongly C-S orthogonality is defined and characterized.

We study the performance of a classical and quantum magnetic Otto cycle with a quantum dot as a working substance using the Fock-Darwin model with the inclusion of the Zeeman interaction. Modulating an external/perpendicular magnetic field, we found in the classical approach an oscillating behavior in the total work that is not perceptible under the quantum formulation. Also, we compare the work and efficiency of this system for different regions of the Entropy, $S(T,B)$, diagram where we found that the quantum version of this engine always shows a reduced performance in comparison to his classical counterpart.

Land degradation and climate change are among the main threats to the sustainability of ecosystems worldwide. Therefore, the restoration of degraded landscapes is essential to maintain the functionality of ecosystems, especially those with greater social, economic and environmental vulnerability. Nevertheless, policy-makers are frequently challenged by deciding on where to prioritize restoration actions, which usually includes to deal with multiple and complex needs under an always short budget. If these decisions are not taken based on proper data and processes, restoration implementation can easily fail. To help decision-makers taking informed decisions on where to implement restoration activities, we have developed a semiautomatic geospatial platform to prioritize areas for restoration activities based on ecological, social and economic variables. This platform takes advantage of the potential to integrate R coding, Google Earth Engine cloud computing and GIS visualization services to generate an interactive geospatial decision-maker tool for restoration. Here, we present a prototype version called "RePlant alpha" which was tested with data from the Central Zone of Chile. This exercise proved that integrating R and GEE was feasible, and that the analysis, with at least six indicators and for a specific region was also feasible to implement even from a personal computer. Therefore, the use of a virtual machine in the cloud with a large number of indicators over large areas is both possible and practical.

We study L_2-approximation problems in the weighted Hilbert spaces in the worst case setting. Three interesting weighted Hilbert spaces appear in this paper, whose weights are equipped with two positive parameters $\ga_j$ and $\az_j$ for $j=1,\,2,\dots,\,d$. We consider the worst case error of algorithms that use finitely many arbitrary continuous linear functionals. We discuss the exponential convergence-(t,s)-weak tractability (EC-(t,s)-WT) of these L_2-approximation problems under the absolute or normalized error criterion. In particular, we obtain the sufficient and necessary conditions for EC-(1,1)-WT and EC-(t,1)-WT with t

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Ship detection from synthetic aperture radar (SAR) imagery is crucial for various fields in real-world applications. Numerous deep learning-based detectors have been investigated for SAR ship detection, which require a substantial amount of labeled data for training. However, SAR data annotation is time-consuming and demands specialized expertise, resulting in that deep learning-based SAR ship detectors struggle due to a lack of annotations. With limited labeled data, semi-supervised learning is a popular approach for boosting detection performance by excavating valuable information from unlabeled data. In this paper, a semi-supervised SAR ship detection network is proposed, termed as Multi-Teacher Dempster-Shafer Evidence Fusion Net-work (MTDSEFN). The MTDSEFN is an enhanced framework based on the basic teacher-student skeleton frame, comprising two branches: the Teacher Group (TG) and the Agency Teacher (AT). The TG utilizes multiple teachers to generate pseudo-labels for different augmentation versions of unlabeled samples, which are then refined to obtain high-quality pseudo-labels by using Dempster-Shafer (D-S) fusion. The AT not only serves to deliver weights of its own teacher to the TG at the end of each epoch, but also updates its own weights after each iteration, enabling the model to effectively learn rich information from unlabeled data. The combination of TG and AT guarantees both reliable pseudo-label generation and learning comprehensive diversity information from numerous unlabeled samples. Extensive experiments were performed on two public SAR ship datasets, and the results demonstrated the effectiveness and superiority of the proposed approach.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

Topological indices have been used to modeling biological and chemical properties of molecules in quantitive structure property relationship studies and quantitive structure activity studies. All the degree based topological indices have been defined via classical degree concept. In this paper we define a novel degree concept for a vertex of a simple connected graph: S degree. And also we define S indices of a simple connected graph by using the S degree concept. We compute the S indices for well-known simple connected graphs such as paths, stars, complete graphs and cycles.

Combustion parameters are the important aspects in the development and research of an internal combustion engines. Hence present work is an attempt to develop an artificial neural network (ANN) model for anticipating the combustion characteristics of computerized CI DI VCR, four strokes, single cylinder, and water cooled engine using mixture of two biodiesel and diesel blends as a fuel. The two biodiesel selected are Jatropha and Simarouba and mixed in the ratio of 75:25. Two biodiesel mixtures is used for the preparation of various blends with diesel. Experiments are carried out at different compression ratio, at different % load and blends B20, B40, B60and neat diesel (B00) fuel to accumulate the assorted combustion data. The input variables are % load, compression ratio, blends and crank angle. The outputs well thought-out are cylinder pressure (CP), net heat release rate (NHRR), cumulative heat release (CHR), rate of pressure rise (RPR), mass fraction burned (MFB) and maximum cylinder pressure. The assessment is focused on developing artificial neural network for the prediction and verifying the combustion characteristics of engine. MATLAB software is used for analysis of different combustion aspects of the engine. Multilayer neural network perceptions are used with Feed-Forward Back Propagation algorithm with performance function for mapping the input and output parameters. The experimental outcomes are compared with ANN estimated results for the analysis. The outcome from the study authenticate that experimental results are in match with ANN results. The accuracy of the ANN model shows the developed model can effectively predict the engine combustion characteristics with excellent regression coefficients ‘R’ and its values are close to unity and the mean square errors are extremely less. ANN model approach is competent towards predicting the combustion aspect of diesel engine with good accuracy

Diastolic dysfunction, a prevalent condition characterized by impaired relaxation and filling of the left ventricle, significantly contributes to heart failure with preserved ejection fraction (HFpEF). Galectin-3, a β-galactoside-binding lectin, has garnered attention as a potential biomarker and mediator of fibrosis and inflammation in cardiovascular diseases. This comprehensive review investigates the impact of galectin-3 on diastolic dysfunction. We explore its molecular mechanisms, including its involvement in cellular signaling pathways and interaction with components of the extracellular matrix. Evidence from both animal models and clinical studies elucidates galectin-3's role in cardiac remodeling, inflammation, and fibrosis, shedding light on the underlying pathophysiology of diastolic dysfunction. Additionally, we examine the diagnostic and therapeutic implications of galectin-3 in diastolic dysfunction, emphasizing its potential as both a biomarker and a therapeutic target. This review underscores the significance of comprehending galectin-3's role in diastolic dysfunction and its promise in enhancing diagnosis and treatment approaches for HFpEF patients.

Euler’s product formula over the primes and Euler’s zeta function equate to enshrine the Fundamental Theorem of Arithmetic that every integer > 1 is the product of a unique set of primes. The product formula has no zero, and with a domain ≤1 Euler’s zeta diverges. Dirichlet’s eta function η(s), negates alternate terms of zeta, permitting convergence when s∈C and Re(s) < 1, and its non-trivial zeros {ρ}, have a deep relationship with the distribution of the primes. The Riemann Hypothesis is that all the non-trivial zeros have Re(ρ) = 1/2. This work examines the symmetries in a partial Euler’s zeta series with a complex domain equating it to the difference between two finite vector series whose matched terms have mirror-image arguments, but whose magnitudes differ when Re(s) ≠ 1/2. Analytical continuation generates a modified eta series η_l(s), in which every l^th term is multiplied by (1-l). If the integer l is appropriately determined by the Im(s), similar paired finite vector series have a difference that closely follows η_l (s) and their terminal vectors intersect in a unique way permitting zeros only when Re(s) = 1/2. Furthermore, those vectors tracking the derivatives of the series, have a special relationship permitting zeros of the differential only when Re(s) > 1/2.

Despite well-documented health benefits of probiotics Saccharomyces, its application in oral health has not been comprehensively assessed. Dental caries is a transmissible disease initiated by acid production of cariogenic bacteria and yeast, such as Streptococcus mutans and Candida albicans, on tooth enamel and followed by subsequent enamel demineralization. Here, we investigated the effect of two Saccharomyces strains (Saccharomyces boulardii, Saccharomyces cerevisiae) on S. mutans-C. albicans cross-kingdom interactions using a cariogenic planktonic model. Viable cells, pH changes and gene expression were measured. S. cerevisiae and S. boulardii inhibited the growth of C. albicans either in dual-, or multi-species conditions. Saccharomyces also inhibited C. albicans hyphal formation. Furthermore, Saccharomyces reduced the acidity of the culture medium which usually plummeted below pH 5 when S. mutans and C. albicans were present in the model. The presence of Saccharomyces maintained the culture medium above 6 even after overnight incubation, demonstrating a protective potential against dental enamel demineralization. S. boulardii significantly downregulated S. mutans atpD and eno genes expression. Overall, our results shed light on a new promising candidate, Saccharomyces, for dental caries prevention due to its potential to create a less cariogenic environment marked by a neutral pH and reduced growth of C. albicans.

Prime numbers are the atoms of mathematics and mathematics is needed to make sense of the real world. Finding the Prime number structure and eventually being able to crack their code is the ultimate goal in what is called Number Theory. From the evolution of species to cryptography, Nature finds help in Prime numbers. One of the most important advances in the study of Prime numbers was the paper by Bernhard Riemann in November 1859 called “Ueber die Anzahl der Primzahlen unter einer gegebenen Grösse” (On the number of primes less than a given quantity). In that paper, Riemann gave a formula for the number of primes less than x in terms the integral of 1/log(x) and the roots (zeros) of the zeta function defined by: Where ζ(z) is a function of a complex variable z that analytically continues the Dirichlet series. Riemann also formulated a conjecture about the location of the zeros of RZF, which fall into two classes: the "trivial zeros" -2, -4, -6, etc., and those whose real part lies between 0 and 1. Riemann's conjecture Riemann hypothesis [RH] was formulated as this: [RH] The real part of every nontrivial zero z* of the RZF is 1/2. Proving the RH is, as of today, one of the most important problems in mathematics. In this paper we will provide a proof of the RH. The proof of the RH will be built following these five parts: PART 1: Description of the RZF PART 2: The C-transformation PART 3: Application of the C-transformation to in Re(z) 0 to obtain ζ(z)=X(z)-Y(z) PART 4: Analysis of the values of z such that X(z)=Y(z), and |X(z)|=|Y(z)|, that equates to ζ(z)=0 Proof that |X(z)|=|Y(z)| only if Re(z)=1/2 Conclude that ζ(z)=0 only if Re(z)=1/2 for Re(z) 0 PART 5: We will also prove that all non-trivial zeros of ζ(z) in the critical line of the form are not distributed randomly. There is a relationship between the values of those zeros and the Harmonic function that leads to an algebraic relationship between any two zeros.

Macromolecular assemblies, such as protein complexes, undergo continuous structural dynamics, including global reconfigurations critical for their function. Two fast analytical methods are widely used to study these global dynamics, namely elastic network model normal mode analysis and principal component analysis of ensembles of structures. These approaches have found wide use in various computational studies, driving the development of complex pipelines in several software packages. One common one has been conformational sampling through hybrid simulations incorporating all-atom molecular dynamics and global modes of motion. However, wide functionality is only available for experienced programmers with limited capabilities for other users. We have, therefore, integrated one popular and extensively developed software for such analyses, the ProDy Python application programming interface, into the Scipion workflow engine. This enables a wider range of users to access a complete range of macromolecular dynamics pipelines beyond the core functionalities available in its command-line applications and the normal mode wizard in VMD. The new protocols and pipelines can be further expanded and integrated into larger workflows together with other software packages for cryo-electron microscopy image analysis and molecular simulations. We present the resulting plugin, Scipion-EM-ProDy, in detail, highlighting the rich functionality made available by its development.

. Protein cysteine S-glycosylation is a relatively rare and less well characterized post-translational modification (PTM). Creating reliable model proteins that carry this modification is challenging. The lack of available model or natural S-glycosylated proteins significantly hampers the development of MS-based methodologies for detecting protein cysteine S-glycosylation in real-world proteomic studies. There is also limited MS-sequencing data describing easier to create synthetic S-glycopeptides. Here, we present the results of an in-depth manual analysis of automatically annotated CID/HCD spectra for model S-glucopeptides. The CID spectra show a long series of y/b-fragment ions with retained S-glucosylation, regardless of the dominant m/z signals corresponding to neutral loss of 1,2-anhydroglucose from the precursor ions. In addition, the spectra show signals manifesting glucosyl transfer from the cysteine position onto Lys, Arg side chains, and a peptide N-terminus. Other spectral evidence indicates that the N-glucosylated initial products of transfer are converted into N-furanosylated (i.e., glycated) structures due to Amadori rearrangement. We discuss the peculiar transfer of the glucose oxocarbenium ion (Glc+) to positively charged guanidinium residue (ArgH+) and propose a mechanism for the gas-phase Amadori rearrangement involving a hydride ion shift.

The implementation of management systems has become a strategic advantage in achieving business goals, especially in industrial organizations, but the implementation of social responsibility requirements is especially ethical. Large multinational companies have long been developing and, in particular, implementing their own codes of conduct, which include their suppliers, to demonstrate their commitment to Corporate Social Responsibility (CSR). The compliance with CSR requirements from stakeholders is thus extended or intertwined with requirements in established management systems (MSs). The objectives of the study were to (1) analyze the different approaches to CSR in internationally recognized cross-industry and industry-specific standards and codes in different industries; (2) select the most appropriate framework for assessing the degree of applicability of CSR in the selected management systems and develop a methodology for its assessment; (3) apply the proposed methodology (referred to as SRIMS) in the selected areas: automotive industry, research organization, and metallurgical industry; (4) through ANOVA, validate its use for assessing the overall level of CSR applicability in an organization's established management systems. The application of the Bonferroni method confirmed the hypotheses that the developed SRIMS model is a sufficiently appropriate tool for assessing the overall level of applicability of CSR requirements to established MSs.

Aiming at solving difficulties related to aero-engine classification and identification, the infrared spectra of aero-engine hot jets are measured by telemetry Fourier transform infrared spectrometer, and a six types aero-engine hot jet spectrum data set is generated. The spectrum data set were randomly sampled at a ratio of 8:1:1 to generate training set, validation set and prediction set. In this paper, a Peak Finding Siamese Convolutional Neural Network (PF-SCNN) is designed to match and classify spectrum data. In the first place, the matching pairs of training set and validation set are made independently with the labels of positive and negative samples creating. The spectrum feature extraction and distance similarity calculation are carried out by the Siamese convolutional neural network (SCNN). When entering the prediction phase, the prediction set and training set are integrated to predict in the trained model. The prediction set labels are ultimately determined by matching them with the training set labels having the highest similarities to ensure accurate predictions. To improve the operation efficiency of the SCNN, a peak finding method is introduced to extract the spectrum peaks. Peak positions of high frequency are counted, while the peak data are extracted. The peak data are used to take the place of the original data for training and prediction. The performance measures are defined as Accuracy, Precision, Recall, Confusion matrix and F1-score, and the prediction accuracy was up to 99%. The experimental results indicate that the proposed PF-SCNN is suitable for our spectral dataset and can complete the task of infrared spectrum classification of aero-engine hot jets.

There has been a great deal of research in the area of using graph engines and graph databases to model network traffic and network attacks, but the novelty of this research lies in visually or graphically representing the Reconnaissance Tactic (TA0043) of the MITRE ATT&amp;CK framework. Using the newly created dataset, UWF-Zeekdata22, based on the MITRE ATT&amp;CK framework, patterns involving network connectivity, connection duration, and data volume were found and loaded into a graph environment. Patterns were also found in the graphed data that match the Reconnaissance as well as other tactics captured by UWF-Zeekdata22. The Star motif was particularly useful in mapping the Reconnaissance tactic. The results of this paper show that graph databases/graph engines can be essential tools for understanding network traffic and trying to detect network intrusions before they happen. Finally, an analysis of the run-time performance of the reduced dataset used to create the graph databases showed that the reduced datasets performed better than the full dataset.

Recent efforts to conceptually design a technologically meaningful electromagnetic retarded engine indicated that this can only be done using the immense charge and current densities which exist in the atomic scale. However, this scale cannot be described by Newtonian physics, and only a quantum description will suffice to describe the dynamics of an electron on this scale properly. Here we study the retarded field quantum engine and highlight the differences between the quantum and the classical retarded engines.

This study addresses the pressing need for flood extent and exposure information in data-scarce and vulnerable regions, with a specific focus on West Africa, particularly Senegal. Leveraging the Google Earth Engine (GEE) platform and integrating data from Sentinel-1 SAR, Global Surface Water, HydroSHEDS, Global Human Layer Settlement, and MODIS Land Cover, our primary ob-jective is to delineate flood extents and compare them with centennial flood-prone areas, offering a comprehensive assessment of exposure during the period from July to October 2022 across Sen-egal's 14 regions. The findings underscore a total inundation area of 2 951 square kilometers, impacting 297 142 people, 175 square kilometers of urban and 16 square kilometers of crops. Notably, August wit-nessed the largest flooded areas, reaching 780 square kilometers, constituting 0.40% of the coun-try's surface. Subsequent regions, including Saint-Louis, Ziguinchor, Fatick, and Matam, experi-enced varying extents of flooding, with August data showing a 1.34% overall overlap compared to centennial flood-prone areas derived from hydrological and hydraulic modeling. This low per-centage reveals the distinct purposes and natures of the two approaches (remote sensing and modeling), as well as their complementarity. Turning to flood exposure, August emerges as the most critical month, affecting 76 595 people (0.43% of the total population). Dakar, Diourbel, Thiès, and Saint-Louis regions bore substantial impacts, affecting 100 707, 57 648, 31 579, and 26 581 people, respectively. These findings emphasize the imperative for comprehensive disaster preparedness and mitigation efforts. The study provides a crucial national-scale perspective to guide Senegal's authorities in formulating effective flood management, intervention, and adaptation strategies.

Products derived from Cannabis sativa have gained increased interest and popularity. As these products become common amongst the public, the heath and potential therapeutic values associated with hemp have become a premier focus of research. While the psychoactive and medicinal properties of Cannabis products have been extensively highlighted in literature, the antibacterial properties of CBD have not been explored in depth. This research serves to examine the antibacterial potential of CBD against Salmonella newington and Salmonella typhimurium. In this study we observed bacterial response to CBD exposure through biological assays, bacterial kinetics, and fluorescence microscopy. Additionally, comparative studies between CBD and ampicillin were conducted against Salmonella typhimurium and Salmonella newington to determine comparative efficacy. Furthermore, we observed potential resistance development of our Salmonella spp. against CBD treatment.

Hybrid power plants have recently emerged as reliable and flexible electricity generation stations by combining multiple renewable energy sources, energy storage systems (ESS), and fossil-based output. However, the effective operation of the hybrid power plants to ensure continuous energy dispatch under challenging conditions is a complex task. This paper proposes a dispatch engine (DE) based on mixed-integer linear programming (MILP) for the planning and management of hybrid power plants. To maintain the committed electricity output, the dispatch engine will provide schedules for operation over extended time periods as well as monitor and reschedule the operation in real-time. Through precise prediction of the PV and wind power output, the proposed approach guarantees optimum scheduling. The precise prediction of the PV and wind power are achieved by employing a predictor of Feed-Forward Neural Network (FFNN) type. With such a dispatch engine, the operational cost of the hybrid power plants, and the use of diesel generators (DGs) are both minimized. A case study is carried out to assess the proposed dispatch engine feasibility. A real-time measurement data pertaining to load, wind, and PV power outputs is obtained from different locations in the Sultanate of Oman. The real-time data is utilized to predict the future output power from PV and the Wind farm over 24 hours. The predicted powers are then used in combination with a PV-Wind-DG-ESS-Grid hybrid plant to evaluate the performance of the proposed dispatch engine. The proposed approach is implemented and simulated using MATLAB. The results of the simulation reveal the proposed Feed-Forward Neural Network’s (FFNN) powerful forecasting abilities. In addition, the results demonstrate that adopting the proposed DE can minimize the use of DG units and reduce plant running expenses.

Hybrid electric vehicles (HEVs) are perceived as a first step towards the future of sustainable transport. Of course, battery electric vehicles (EVs) are currently ideal for what is wanted to stand for transport in the future. The lack of infrastructure for these vehicles makes many potential users choose hybrid vehicles in these conditions. This paper analyzes the influence of the engine and electric motor of hybrid vehicles on their performances. Three engines with slightly different power and close characteristics were considered for configured models. Also, two electric motors with very different power but having a very close maximum continuous torque have been used in models. One is an induction motor, and the other is a permanent magnet synchronous motor. ADVISOR software has been used for vehicles configuration and simulation. Series and parallel hybrid vehicles have been considered. The main dynamic performances and the fuel consumption in two driving cycles were compared for the configured models. Three conventional models with the same engines used in HEVs have also been simulated for reference. The results highlight that in the case of HEVs, the choice of combination engine/electric motor is crucial in obtaining the best report between dynamic performances and low fuel consumption, and implicitly a low negative impact on the environment.

This study presents the evaluation of an ion exchange resin-based installation designed for the recycling of engine coolants, specifically ethylene glycol (EG) and propylene glycol (PG). The recycling process aims to restore the coolant to meet the stringent ASTM standards for both new and recycled coolants. A combination of physical-chemical methods, gas chromatography-mass spectrometry (GC-MS), and inductively coupled plasma mass spectrometry (ICP-MS) was employed to analyze and validate the purity and performance of the recycled product. The experimental setup included performance tests to assess the efficacy of the recycled coolants in comparison to new coolant standards. The results demonstrate that the recycled EG coolants exhibit comparable quality to new coolants, with all critical parameters falling within the acceptable ASTM limits. This indicates that the ion exchange resin method is a viable and efficient solution for the recycling of engine coolants, offering an environmentally friendly alternative to the disposal of used coolants while ensuring compliance with industry standards.

The viewpoint and reaction of a country towards climate change are shaped by its political, cultural, and scientific backgrounds, in addition to the distinct characteristics of its evolving climate and the anticipated and actual consequences of the phenomenon in the times ahead. A region's climate has a significant impact on how water is managed and used, mostly in the primary sector (agroforestry systems, livestock, and agriculture), and both the distribution of ecosystem types and the amount and spreading of species on Earth. As a result, the environment and agricultural practices are affected by climate, so evaluating both distribution and evolution is extremely pertinent. Towards this aim, the climate distribution and evolution in the S. Francisco River basin (SFRB) is assessed in three periods (1970−2000, 1981−2022) in the past and 20412060 in the future from an ensemble of GCMs under two SSPs (Shared Socioeconomic Pathways), SSP2-4.5 and SSP5-8.5. The Köppen-Geiger (KG) climate classification system is analyzed, and climate change impacts are inferred for this watershed located in central-eastern Brazil, covering an area equivalent to 8% of the country. Results predict the disappearance of the hot-summer (Csa) and warm-summer (Csb) Mediterranean climates, and a reduction/increase in the tropical savanna with dry winter (Aw)/dry summer (As). A striking increase in the semi-arid hot (BSh-steppe) climate is predicted with a higher percentage (10%) under SSP5-8.5. The Source and the mouth of SFRB are projected to endure the major impacts of climate change that is followed by a predicted increase/decrease in temperature/precipitation. Future freshwater resource availability, and quality for human use will all be impacted. Consequences on ecosystems, agricultural and for the socioeconomic sectors within the SFRB might deepen the current contrasts between regions, urban and rural areas, and even between population groups, thus translating to a larger extent, the inequality that still characterizes Brazilian society. Maps depicting land use and cover changes in the São Francisco River basin from 1985 to 2022 highlight tendencies such as urbanization, agricultural expansion, deforestation, and changes in shrubland and water bodies. Urban areas fluctuated slightly, while cropland significantly increased from 33.57% to 45.45%, and forest areas decreased from 3.88% to 3.50%. Socioeconomic data reveals disparities among municipalities: 74.46% with medium Human Development Index (HDI), 0.59% with very high HDI, and 9.11% with low HDI. Most municipalities have a Gross Domestic Product (GDP) per capita below US$ 6,000. Population distribution maps show a predominance of small to medium-sized urban and rural communities, reflecting the basin's dispersed demographic and economic profile. To build routes towards a shared sustainable goal—namely, to adapt and reduce the expected climate change impacts in SFRB—it is imperative that integrated measures be conducted with the cooperation of stakeholders, local population, and decision-makers.

This research presents a comprehensive framework for efficiently generating forest fire datasets from Google Earth Engine data sources. The primary contribution of this work lies in providing a methodology to swiftly extract forest fire factors without the need for permissions or access to private datasets, rendering the dataset openly accessible and shared without barriers. Furthermore, given that the remote sensing data used is a global dataset, it can be applied in any region without restrictions. In this study, Peninsular Malaysia is chosen as a case study to demonstrate the framework's effectiveness. The generated dataset includes essential variables including the climate and environment, landcover, topography, and anthropogenic factors facilitating the analysis of fire occurrences. The methodology empowers data scientists, enabling them to leverage their analytical skills on the extracted dataset without requiring specialized remote sensing knowledge. Additionally, this study also showcases the adoption of large language models, specifically GPT-4 with the Noteable plugin, as a tool for conducting preliminary analyses on the generated dataset. Sample analyses reveal that several key features, including the KBDI, LST, PDSI, climate water deficit, and precipitation, significantly impact forest fire occurrences in Peninsular Malaysia. Despite the successful application of the GPT-4 with Noteable plugin, certain limitations and challenges are identified, highlighting the necessity for further validation of the tool's applicability and limitations. This study encourages future research to (1) adopt the proposed framework in other regions, (2) explore more detailed analyses encompassing all variables, and (3) leverage machine learning for advanced forecasting.

This article is about a framework for determining the degree of realism of any given 1 passenger ride motion discomfort measurement formula. After providing some context and reviewing 2 evidence of deficiency in currently popular ride motion discomfort measurement formulas, the article 3 outlines the research program that needs to be carried out in order to establish such a framework. 4 The research begins with gathering recordings of uncomfortable ride motion episodes encountered in 5 a chosen type of passenger transport service. It then has test subjects compare the episodes via a ride 6 motion simulator and adjust their amplitudes pair wise until they cause equal discomfort. It explains 7 how to take the pair wise amplitude adjustments and determine amplitude adjustments that bring all 8 of the motion episode recordings to a common level of discomfort so that they form a normalized set. 9 Then, the lower the scatter of the scores assigned by any given discomfort measurement formula to 10 the members of that set, the more realistic that formula will be for the chosen service.

The strategy of any organization is based on the growth of its customer base, and one of 5 its principles is that selling a product to an existing customer is much more profitable than acquiring 6 a new customer. However, this approach has several opportunities for improvement, since it usu- 7 ally has a totally reactive approach, which does not give opportunity to the areas specialized in 8 customer experience and recovery, to give an effective response for that moment, since the customer 9 is gone at the time of the intervention. This happens because usually a diagnostic analysis of cus- 10 tomers who have stopped buying products or services in a defined period, commonly three (3) pe- 11 riods or months, is performed. This thesis work challenges the way to face this problem, and pro- 12 poses the development of a complete solution, which does not focus exclusively on the prediction 13 of churn, as is usually done in the state of the art research, but to intervene in different interactions 14 that can be carried out with customers. The above focused not only to prevent customer churn, but 15 to generate an added value of continuous improvement in sales processes, increase customer pene- 16 tration, leading to an improvement in customer experience and consequently, an increase in cus- 17 tomer loyalty.

In this systematic review, the PRISMA method was applied to examine publications from the last two decades that have investigated the noxious gaseous emissions from dairy barns. The aim was to analyse the outcomes from literature studies estimating the quantities of polluting gases produced in dairy barns, with specific focus on ammonia (NH₃) emissions. The review also explores proposed methods to reduce the associated effects through mitigation strategies. Estimation of NH₃ emissions is significantly influenced by the complex interactions among several factors, including animal management practices, such as controlling animal behavioral activities; manure management, like utilising practices for floor manure removal; the type of structure housing the animals, whether it is naturally or mechanically ventilated; and environmental conditions, such as the effects of temperature, wind speed, relative humidity, and ventilation rate on NH₃ release in the barn. These influential components have been considered by researchers, identifying targeted mitigation strategies. Despite growing attention to the issue, gaps in the scientific literature were identified and discussed, particularly regarding the analysis of mitigation strategies and their long-term impacts (i.e., environmental, economic and productivity-wise).

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Micro-combs [1-4] - optical frequency combs generated by integrated micro-cavity resonators – offer the full potential of their bulk counterparts [5,6], but in an integrated footprint. The discovery of temporal soliton states (DKS – dissipative Kerr solitons) [4,7-11] as a means of mode-locking micro-combs has enabled breakthroughs in many fields including spectroscopy [12,13], microwave photonics [14], frequency synthesis [15], optical ranging [16,17], quantum sources [18,19], metrology [20,21] and more. One of their most promising applications has been optical fibre communications where they have enabled massively parallel ultrahigh capacity multiplexed data transmission [22,23]. Here, by using a new and powerful class of micro-comb called “soliton crystals” [11], we achieve unprecedented data transmission over standard optical fibre using a single integrated chip source. We demonstrate a line rate of 44.2 Terabits per second (Tb/s) using the telecommunications C-band at 1550nm with a spectral efficiency – a critically important performance metric - of 10.4 bits/s/Hz. Soliton crystals exhibit robust and stable generation and operation as well as a high intrinsic efficiency that, together with a low soliton micro-comb spacing of 48.9 GHz enable the use of a very high coherent data modulation format of 64 QAM (quadrature amplitude modulated). We demonstrate error free transmission over 75 km of standard optical fibre in the laboratory as well as in a field trial over an installed metropolitan optical fibre network. These experiments were greatly aided by the ability of the soliton crystals to operate without stabilization or feedback control. This work demonstrates the capability of optical soliton crystal micro-combs to perform in demanding and practical optical communications networks.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost variances using proprietary C-S and S-C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

Focusing on the problem of identifying and classifying aero-engine models, this paper measures the infrared spectrum data of aero-engine hot jets using a telemetry Fourier transform infrared spectrometer. Simultaneously, infrared spectral data sets with the six different types of aero-engines are created. For the purpose of classifying and identifying infrared spectral data, a CNN architecture based on the continuous wavelet transform peak seeking attention mechanism (CWT-AM-CNN) is suggested. This method calculates the peak value of middle wave band by continuous wavelet transform, and the peak data is extracted by the statistics of the wave number locations with high frequency. Attention mechanism is used for the peak data, and the attention mechanism is weighted to the feature map of the feature extraction block. The training set, vali-dation set and prediction set are divided in the ratio of 8:1:1 for the infrared spectral data sets. For three different data sets, CWT-AM-CNN proposed in this paper is compared with the classical classifier algorithm based on CO2 feature vector and the popular AE, RNN and LSTM spectral processing networks. The prediction accuracy of the proposed algorithm in the three data sets is as high as 97%, and the lightweight network structure design not only guarantees high precision, but also has a fast running speed, which can realize the rapid and high-precision classification of the infrared spectral data of the aero-engine hot jets.

We report on the occurrence of natural Magnesium Alumina Silicate Hydrate (M-(A)-S-H) cement at Feragen and Leka in eastern and western Trøndelag Norway, respectively. Both occurrences are located in the sub-arctic climate zone and form in glacial till and moraine material deposited on ultramafic rock during the Weichselian glaciation. Weathering of serpentinized peridotite dissolve brucite and result in a relative high pH alkaline fluid that subsequently reacts with the felsic minerals of the till (quartz, plagioclase, K-feldspar) to form a cement consisting of an amorphous material or a mixture of nanocrystalline Mg-rich phyllosilicates, including illite. The presence of plagioclase in the till results in the enrichment of alumina in the cement, i.e., forms M-A-S-H instead of the M-S-H cement. Dissolution of quartz results in numerous etch-pits and negative quartz crystals filled with M-A-S-H cement. Where the quartz dissolution is faster that the cement precipitation, a honeycomb-like texture is formed. Compositionally the cemented till (tillite) contains more MgO and has a higher loss of ignition than the till, suggesting that the cement is formed by a MgO fluid that previously reacted with the peridotite. The M-(A)-S-H cemented till represent a new type of duricrust, coined magsilcrete. The study of natural Mg-cement provides information on peridotites as a Mg-source for Mg-cement and as a feedstock for CO2 sequestration.

This note first summarizes the history of the manuscript "On a Continuum Model for Avalanche Flow and Its Simplified Variants" by Grigorian and Ostroumov―published in the Special Issue on snow avalanche dynamics of Geosciences―since the early 1990s and explains the guiding principles in editing it for publication. The changes are then detailed and some explanatory notes given for the benefit of readers who are not familiar with the early Russian work on snow avalanche dynamics. Finally, the editor's personal views as to why he still considers this paper of relevance for avalanche dynamics research today are presented in brief essays on key aspects of the paper, namely the role of simple and complex models in avalanche research and mitigation work, the status and possible applications of Grigorian's stress-limited friction law, and non-monotonicity of the dynamics of the Grigorian–Ostroumov model in the friction coefficient. A comparison of the erosion model proposed by those authors with two other models suggests to enhance it with an additional equation for the balance of tangential momentum across the shock front. A preliminary analysis indicates that continuous scouring entrainment is possible only in a restricted parameter range and that there is a second erosion regime with delayed entrainment.

Gas turbine engines are widely used in various industries such as aviation, power generation, and marine propulsion due to their high efficiency and reliability. The combustion chamber of a gas turbine engine design contains a number of elements, including as the chamber's size and form, the fuel injection system, the ignition system, and the cooling system and it plays a critical role in the performance and efficiency of the engine. This research discusses the fabrication of a combustion chamber model for a gas turbine engine. The aim of this research is to develop a combustion chamber that is cost-effective, easily available, and can be fabricated in less time. The research covers the different types of combustion chambers used in gas turbine engines and compares their advantages and disadvantages. It then selects the best type of combustion chamber for the gas turbine engine based on its cost, availability, and fabrication time, Efficiency and high power to fuel ratio. The report also describes the fabrication process involved, including the techniques and materials used, along with safety precautions and environmental protection measures. Lastly, the research suggests future improvements and potential applications for the fabricated combustion chamber model.

The present Feature Paper highlights the application of bacterial surface (S-) layer proteins as versatile components for the fabrication of biosensors. One technologically relevant feature of S‑layer proteins is their ability to self-assemble on many surfaces and interfaces to form a crystalline 2D protein lattice. The S-layer lattice on the surface of a biosensor becomes part of the interface architecture, linking the bioreceptor to the transducer interface, which may cause signal amplification. The S-layer lattice as ultrathin, highly porous structure with functional groups in a well-defined special distribution and orientation and an overall anti-fouling characteristics can significantly raise the limit in terms of variety and ease of bioreceptor immobilization, compactness of bioreceptor molecule arrangement, sensitivity, specificity, and detection limit for many types of biosensors. The present paper discusses and summarizes examples for the successful implementation of S-layer lattices on biosensor surfaces in order to give a comprehensive overview on the application potential of these bioinspired S-layer protein-based biosensors.

Graphene is perhaps the most prominent “Dirac material,” a class of systems whose electronic structure gives rise to charge carriers that behave as relativistic fermions. In multilayer graphene several crystal sheets are stacked such that the honeycomb lattice of each layer is displaced along one of the lattice edges. When subject to an external magnetic field, the scaling of the multilayer energy spectrum with the magnetic field, and thus the system’s thermodynamic behavior, depends strongly on the number of layers. With this in mind, we examine the performance of a finite-time endoreversible Otto cycle with multilayer graphene as its working medium. We show that there exists a simple relationship between the engine efficiency and the number of layers, and that the efficiency at maximum power can exceed that of a classical endoreversible Otto cycle.

Wastewater-Based Epidemiology (WBE) is currently used to monitor not only the spread of the pandemic virus SARS-CoV-2 but also for other viruses in endemic conditions, particularly in the absence of syndromic surveillance. Continuous monitoring of sewage requires high costs and significant time investment, highlighting the need for standardized methods and structured monitoring strategies. In this context, we conducted weekly wastewater monitoring in northwestern Italy, targeting Human Adenovirus (HAdV), Norovirus Genogroup II (NoVggII), Enterovirus (EV), and SARS-CoV-2. Samples collected at the entrance of treatment plants were concentrated using PEG/NaCl precipitation and viral nucleic acids were extracted and detected by real-time (RT-)qPCR. NoVggII resulted the most identified target (84.4%), followed by HAdV, SARS-CoV-2, and EV. Only HAdV and EV exhibited seasonal peaks in spring and summer. SARS-CoV-2 results compared with data previously collected in the same study area (February 2021 to September 2021) revealed a shift from an epidemic to a pandemic status, likely due to the evolution of variants. In conclusion, WBE, using standardized methods and an efficient monitoring strategy, proves valuable for virus surveillance in pandemic and epidemic scenarios, enabling the identification of temporal-local distribution patterns that are useful for making informed public health decision.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

Nowadays, the identification and characterization of grapevine cultivars resilient to climate and water stress while preserving quality traits is crucial for the wine industry. Therefore, the objective of this work was to characterize according to their aromatic potential 9 white and 6 red minority cultivars recently recovered from Castilla-La Mancha region (Spain), subjected at two different water deficit regimes: rainfed, with subsistence irrigation, and irrigated. For this, the varietal aromatic potential index (IPAv) and the detailed aromatic composition were analyzed by HS-SBSE-GC/MS, in extracts of two different ph. For IPAv values, red varieties did not show a clear trend with respect to irrigation. However, in white minority varieties, higher values were obtained under irrigation conditions. Thus, a clear differentiation of the minority varieties in comparison to the references was observed, primarily attributed to the content of esters and acids, in both white and red varieties. A notable contrast was observed at different pH, indicating a greater extractability of certain compounds like linalool, under more acidic conditions. This suggests that some recovered minority cultivars could be promising for cultivation in semi-arid regions with limited water, contributing to the wine sector sustainability in the future.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

This paper reports the efforts made and experiences gained in developing the Flood Prevention and Emergency Response System (FPERS) powered by Google Earth Engine, with focus on its applications at the three stages of floods. At the post-flood stage, FPERS integrates various remote sensing imageries, including Formosat-2 optical imagery, to detect and monitor barrier lakes, synthetic aperture radar imagery to derive an inundation map, and high-spatial-resolution photographs taken by unmanned aerial vehicles to evaluate damage to river channels and structures. At the pre-flood stage, a huge amount of geospatial data are integrated in FPERS and are categorized as typhoon forecast and archive, disaster prevention and warning, disaster events and analysis, or basic data and layers. At the during-flood stage, three strategies are implemented to facilitate the access of the real-time data: presenting the key information, making a sound recommendation, and supporting the decision-making. The example of Typhoon Soudelor in August of 2015 is used to demonstrate how FPERS was employed to support the work of flood prevention and emergency response from 2013 to 2016. The capability of switching among different topographic models and the flexibility of managing and searching data through a geospatial database are also explained, and suggestions are made for future works.

Let R be a commutative graded ring with unity, S be a multiplicative subset of homogeneous elements of R and P be a graded ideal of R such that P\bigcap S=\emptyset In this article, we introduce several results concerning graded S-prime ideals. Then we introduce the concept of graded weakly S-prime ideals which is a generalization of graded weakly prime ideals. We say that P is a graded weakly S-prime ideal of R if there exists s\in S such that for all x, y\in h(R), if 0\neq xy\in P, then sx\in P or sy\in P. We show that graded weakly S-prime ideals have many acquaintance properties to these of graded weakly prime ideals.

Translation of basic animal research to find effective methods of diagnosing and treating human neurological disorders requires parallel analysis infrastructures. Small animals such as mice provide exploratory animal disease models. However, many interventions developed using small animal models fail to translate to human use due to physical or biological differences. Recently, large-animal minipigs have emerged in neuroscience due to both brain similarity and economic advantages. Medical image processing is a crucial part of research as it allows researchers to monitor their experiments and understand disease development. However, although many algorithms are created and optimized for MR analysis of human data, those tools are not directly applicable or sufficiently sensitive to measure minipig data. In this work, we propose PigSNIPE - a pipeline for the automated handling, processing, and analyzing of large-scale data sets of minipig MR images. The pipeline allows for image registration, AC-PC alignment, landmark detection, skull stripping, brainmasks and intracranial volume segmentation (DICE 0.98), tissue segmentation (DICE 0.82), and caudate-putamen brain segmentation (DICE 0.8) in under two minutes. To the best of our knowledge, this is the first automated pipeline tool aimed at large animal images.

This present work explores the performance of a thermal-magnetic engine of Otto type, considering as a working substance an effective interacting spin model corresponding to the q− state clock model. We obtain all the thermodynamic quantities for the q = 2, 4, 6, 8 cases in a small lattice size (3×3 with free boundary conditions) by using the exact partition function calculated from the energies of all the accessible microstates of the system. The extension to bigger lattices was performed using the mean-field approximation. Our results indicate that the total work extraction of the cycle is highest for the q=4 case, while the performance for the Ising model (q=2) is the lowest of all cases studied. These results are strongly linked with the phase diagram of the working substance and the location of the cycle in the different magnetic phases present, where we find that the transition from a ferromagnetic to a paramagnetic phase extracts more work than one of the Berezinskii–Kosterlitz–Thouless to paramagnetic type. Additionally, as the size of the lattice increases, the extraction work is lower than smaller lattices for all values of q presented in this study.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

We study the effect of the degeneracy factor in the energy levels of the well-known Landau problem for a magnetic engine. The scheme of the cycle is composed of two adiabatic processes and two isomagnetic processes driven by a quasi-static modulation of external magnetic field intensity. We derive the analytical expression of the relation between the magnetic field and temperature along the adiabatic process and, in particular, reproduce the expression for the efficiency as a function of the compression ratio.

We have carried out a systematic review of the scientific literature published on PM and, more specifically, on its presence in fish and seafood of interest to the population from Mediterranean area. Given its preference and wide acceptability in the scientific community, we followed the PRISMA. The potential functional and clinical toxicity in humans due to MP in fish must be considered by the chemical composition of the microplastics the presence of PM and its additives, associated contaminants and pathogens in fish and shellfish, as well as the possible effects on human health, requires improving legislation on evaluation and providing a basis for consumer protection.

Immunosuppressed individuals, such as people living with HIV (PLWH), remain vulnerable to severe COVID-19. We analyzed the persistence of specific SARS-CoV-2 humoral and cellular immune responses in a retrospective, cross-sectional study in PLWH on antiretroviral therapy. Among 104 participants, 70.2% had anti-S IgG antibodies and 55.8% had significant neutralizing activity against the Omicron variant in a surrogate virus neutralization test. Only 38.5% were vaccinated (8.76 ± 4.1 months prior), all displaying anti-S IgG, 75% with neutralizing antibodies and anti-S IgA. 29.8% had no SARS-CoV-2 serologic markers and displayed significantly lower CD4 counts and HIV viral load. Severe immunosuppression (present in 12.5% of participants) was linked to lower levels of detectable anti-S IgG (0.0003), anti-S IgA (p &lt; 0.0001) and lack of neutralizing activity against Omicron variant (p &lt; 0.0001). T-cell responses were present in 86.7% of tested participants, even in those lacking serological markers. In PLWH without severe immunosuppression, neutralizing antibodies and T-cell responses persisted for up to 9 months post-infection or vaccination. Advanced immunosuppression led to diminished humoral immunity, but retained cellular immune.

This paper presents an operational approach for detecting floods and establishing flood extent using Sentinel-1 radar imagery with Google Earth Engine. Flooded areas are identified using a change-detection method based on the normalized difference. The HAND algorithm is used to delineate zones for processing. The approach was tested and calibrated at small scale to identify optimal parameters for flood detection. It was then applied to the whole of the island of Madagascar after the cyclone Batsirai in 2022. The proposed method is enabled by the computing power and data availability of Google Earth Engine and Google Colab. The results show satisfactory accuracy in delineating flooded areas. The advantages of this approach are its rapidity, online availability and ability to detect floods over a wide area. The approach relying on Google tools thus offers an effective solution for generating a large-scale synoptic picture to inform hazard management decision-making. However, one of the method’s drawbacks is that it depends to a large extent on frequent radar imagery being available at the time of flood events and on free access to the platform. These drawbacks will need to be taken into account in an operational scenario.

Crop type and field boundary mapping enable cost-efficient crop management on the field scale and serve as the basis for yield forecasts. Our study uses a data set with crop types and corresponding field borders from the federal state of Bavaria, Germany, as documented by farmers from 2016 to 2018. The study classified corn, winter wheat, barley, sugar beet, potato, and rapeseed as the main crops grown in Upper Bavaria. Corresponding Sentinel-2 data sets include the normalised difference vegetation index (NDVI) and raw band data from 2016 to 2018 for each selected field. The influences of clouds, raw bands, and NDVI on crop type classification are analysed, and the classification algorithms, i.e., support vector machine (SVM) and random forest (RF), are compared. Field boundary detection and extraction are based on non-iterative clustering and a newly developed procedure based on Canny edge detection. The results emphasise the application of Sentinel’s raw bands (B1–B12) and RF, which outperforms SVM with an accuracy of up to 94%. Furthermore, we forecast data for an unknown year, which slightly reduces the classification accuracy. The results demonstrate the usefulness of the proof-of-concept and its readiness for use in real applications.

The aim of this work is to present a design approach of a Shock-Induced Combustion Ramjet (Shcramjet) inlet, and present its optimization in terms of the flow and geometrical parameters. The flow properties of mixed compression type inlet of a Shcramjet are examined using analytical and numerical techniques. The geometries obtained with variations in the wedge angles, length, height and cowl lip positions are used to study the flow characteristics of inlet, identifying bow shock temperature ratio as the optimization parameter. The two-dimensional geometries of two-shock and three-shock inlet models designed analytically for shock-on-lip condition at Mach 12.5 and an altitude of 32.5 km are numerically simulated in OpenFOAM CFD Toolbox. A density based compressible CFD solver based on central upwind schemes of Kurganov and Tadmore is used to solve 2D inviscid Euler equations. The inlet total pressure recovery is expressed as a function of temperature ratios of compression shocks, and is found to have a maxima at a bow shock temperature ratio at the design condition when the bow and external shocks have equal strengths. The effect of considering the flow to be calorically imperfect is studied numerically, and the deviation from the analytical design is presented.

Astrocytes perform a wide variety of essential functions defining normal operation of the nervous system, and are active contributors to the pathogenesis of neurodegenerative disorders such as Alzheimer among others. Recent data provide compelling evidence that distinct reactive astrocyte states are associated with specific stages of Alzheimer´s disease. The advent of transcriptomics technologies enables rapid progress in the characterisation of such pathological astrocyte states. In this review, we provide an overview of the origin, main functions, molecular and morphological features of astrocytes in physiological as well as pathological conditions related to Alzheimer´s disease. We will also explore the main roles of astrocytes in the pathogenesis of Alzheimer´s disease and summarize main transcriptional changes and altered molecular pathways observed in astrocytes during the course of the disease.

Rice has become the second major food among rural people. It is one of the most nutrient and low-cost food available in Asia. Rice is composed of two major subspecies as Japonica and Indica and it belongs to the Poaceae family. The World Bank predicts that rice demand will grow 51% faster than population growth in 2025. It is high time to develop a model which predicts the type of infected paddy leaf and avoids the loss of grains. In this paper, the proposed hybrid CNN model, three CNN networks with different layer properties are trained parallel. The extracted feature from these CNN networks is combined to provide the classification of the type of infected leaf. Fieldwork was carried and about 340 samples are collected from five different types of classes. The proposed hybrid model was tested with both the fieldwork dataset and also with an available dataset on the internet. The experimental results show that the proposed model outperforms the other CNN network and yields an accuracy value of 98%, a precision value of 95%, and a misclassification rate of 4% respectively.

Pigs are a social species and they stablish hierarchies for a better use of resources and to reduce conflicts. However, in pig production, the opportunities for growing can differ in dominant and subordinate animals. In the present study a system was tested to perform a Dominance versus Subordinate test in growing pigs to investigate how the hierarchy affects feeding behaviour, growth and gut microbiota assessed in faeces. 64 animals housed in eight different pens were used, with four castrated males and four females in each one, weighing 18kg at arrival and maintained during the whole growing period, until 140 kg. Three stool samplings were obtained from the animals directly from the anus to avoid contamination of the faeces on 58, 100 and 133 days after the start of the study to investigate the microbiota composition. The dominant animals had higher gains during the growing period that the subordinate. In addition, they were performing more visits to the feeder throughout the day. Differential abundance patterns were observed in five bacterial genera, Oliverpabstia, Peptococcus, and Faecalbacterium being more abundant in dominant animals and Holdemanella and Acetitomaculum being overrepresented in subordinate ones. This microbial biomarker accurately classified dominant versus subordinate groups of samples with an AUC of 0.92.

The rising importance of Big Data in modern information analysis is supported by vast quantities of user data, but it is only possible to collect sufficient data for all tasks within certain data-gathering contexts. There are many cases where a domain is too novel, too niche, or too sparsely collected to adequately support Big Data tasks. To remedy this, we have created ADG Engine that allows for the generation of additional data that follows the trends and patterns of the data that’s already been collected. Using a database structure that tracks users across different activity types, ADG Engine can use all available information to maximize the authenticity of the generated data. Our efforts are particularly geared towards data analytics by identifying abnormalities in the data and allowing the user to generate normal and abnormal data at custom ratios. In situations where it would be impractical or impossible to expand the available dataset by collecting more data, it can still be possible to move forward with algorithmically expanded data datasets.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

\textsc{Background} Often, in biology, we are faced with the problem of exploring relevant unknown biological hypotheses in the form of myriads of combination of factors that might be affecting the pathway under certain conditions. Currently, a major problem in biology is to cherry pick the combinations based on expert advice, literature survey or guesses for investigation. The search and wet lab testing of these combinations costs a lot in terms of time, investment and energy. In a recent development of the PORCN-WNT inhibitor ETC-1922159 for colorectal cancer, a list of down-regulated genes were recorded in a time buffer after the administration of the drug. The regulation of the genes were recorded individually but for a majority, it is still not known which higher ($\geq 2$) order combinations might be playing a greater role in the pathway. \textsc{Results} The pipeline provides a prioritised list of important $2^{nd}$ order combinations of a range of family of genes involved in the Wnt pathway. More specifically, it reveals the various unexplored FZD-WNT combinations that have been untested till now in the pathway. In relation to ETC-1922159 affected combinations, the down-regulation of LGR-RNF family after the drug treatment is evident in these rankings as it takes bottom priorities for LGR5-RNF43 combination. The LGR6-RNF43 takes higher ranking than LGR5-RNF43, indicating that it might not be playing a greater role as LGR5 during the Wnt enhancing signals. These rankings confirm the efficacy of the proposed search engine design. \textsc{Conclusion} A pipeline has been developed to prioritise an $n^{th}$ order combination of factors that affect a signaling pathway. It takes into account the sensitivity indices computed from variance based (SOBOL) and density-kernel based (HSIC) methods to estimate the influence of each factor or combination of factors. These are then fed as feature vectors into a powerful support vector ranking algorithm that produces a ranked list of the interactions/combinations.

Photovoltaic (PV) systems, which are renewable energy sources, are increasingly being utilized in distributed generation. To maintain a stable energy balance, energy storage systems such as batteries (BAT) play a vital role. Electric vehicles (EVs) offer a promising solution with rechargeable battery systems for operation. The BATs must maintain their state of charge within design boundaries, despite intermittent PV and load power fluctuations, and advanced power control and management techniques are essential for their effective operation. The article evaluates an intelligent controller that uses a Sliding Mode Control adaptive deep learning algorithm Convolutional Neural Networks (SMC-CNN) and a unique Strategy for managing supervisory power. (SPMS) for photovoltaic systems with battery energy storage for better regulation of DC bus voltage. SMC-CNN offers exceptional resilience and seamless functionality, minimizing fluctuations in DC bus voltage in the control strategy design requirements. The primary goals are maintaining a consistent power supply and ensuring continuous service by preventing system components from exceeding capacity. This study aims to enhance the control of DC bus voltage in the PV and battery system, with the primary significance focusing on the following aspects. The advanced SPMS has been created, incorporating control system constraints to enhance SOC balancing speed and reduce fluctuations in DC bus voltage. Power flow management involves optimizing energy flow between the PV system, battery system, and load while minimizing battery capacity requirements. The proposed SMC-CNN and SPMS are demonstrated through real-time simulation using Matlab/Simulink, as demonstrated in comprehensive case studies.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

The COVID-19 pandemic has not only affected public health but has also significantly impacted the economy. Bandung, a bustling city in Indonesia serving as a satellite to the capital, has been hit hard due to its high population density, mobility, and reliance on the tourism, trade, and transportation sectors. Using a Computable General Equilibrium (CGE) model developed at the inter-regional level of Indonesia, this study investigates the microeconomic indicators of several economic activities in Bandung to assess the impact of the pandemic. Additionally, the study examines the role of private sector actors in contributing to the sustainable recovery efforts toward achieving Sustainable Development Goals (SDGs) amidst the pandemic. The findings reveal that Bandung's transportation, accommodation, food and beverage, water supply, and trade sectors experienced a significant decline in economic activity. However, there was a gradual recovery with increased economic activity between 2019 and 2021. Private sector actors and the health sector were the main drivers of economic recovery, with other sectors also contributing to the efforts.

Alternative fuels have the potential to reduce exhaust emissions in the transportation sector. In this study, the effects of oxygenated fuels on the performance and emissions of a gasoline single-cylinder spark-ignition engine have been investigated experimentally. Experiments were conducted using a DIDACTA-T85 testbed under full load conditions and variable engine speed. Performance tests were performed by measuring the brake torque, brake power, brake mean effective pressure (BMEP), brake specific fuel consumption (BSFC), and brake thermal efficiency (BTE). The tested fuel blends were G0, E10, A10, and M10. G0 represented the base fuel and pure gasoline. E10, A10, and M10 were represented by a 10% volume of ethanol, acetone, and methanol in gasoline respectively. Results showed that M10 produced better engine performance in terms of brake torque, brake power, and BMEP, while E10 performed better results in terms of BSFC and BTE. A10 gave the lowest value in NOx emission at all engine speeds. On the other hand, it increased the NOX emission for E10 and M10 blends. This study showed that oxygenated fuel blends significantly reduced carbon monoxide emission at all engine speeds whereas carbon dioxide emission was higher at the highest engine speed.

Accurate inundation maps for flooded wetlands and rivers are a critical resource for their management and conservation. In this paper we automate a method (thresholding of the short-wave infrared band) for classifying inundation, using Landsat imagery and Google Earth Engine. We demonstrate the method in the Okavango Delta, northern Botswana, a complex case study due to the spectral overlap between inundated areas covered with aquatic vegetation and dryland vegetation classes on satellite imagery. Inundation classifications in the Okavango Delta have predominately been implemented on broad spatial resolution images. We present the longest time series to date (1990-2019) of inundation maps at high spatial resolution (30m) for the Okavango Delta. We validated the maps using image-based and in situ data accuracy assessments, with accuracy ranging from 91.5 - 98.1%. Use of Landsat imagery resulted in consistently lower estimates of inundation extent than previous studies, likely due to the increased number of mixed pixels that occur when using broad spatial resolution imagery, which can lead to overestimations of the size of inundated areas. We provide the inundation maps and Google Earth Engine code for public use.

(1) Background: The diagnosis of lumbosacral radiculopathy involves anamnesis, assessment of sensitivity and strength, diagnostic imaging—usually magnetic resonance imaging (MRI)—and electrodiagnostic testing (EDX), typically electromyography (EMG) and electroneurography (ENG). MRI evaluates the structures supporting the spinal cord, while EDX evaluates root functionality. The present study aimed to analyze the concordance of MRI and EDX findings in patients with clinically suspected radiculopathy. Additionally, we investigated the comparison between these two reference tests and various clinical variables and questionnaires. (2) Methods: We designed a prospective epidemiological study of consecutive cases with an observational, descriptive, cross-sectional, and double-blind nature following the STROBE guidelines, encompassing 142 patients with clinical suspicion of lumbosacral radiculopathy. (3) Results: Of the sample, 58.5% tested positive for radiculopathy using EDX as the reference test, while 45.8% tested positive using MRI. The comparison between MRI and EDX in the diagnosis of radiculopathy in patients with clinical suspicion was not significant; the overall agreement was 40.8%. Only the years with symptoms were comparatively significant between the positive and negative radiculopathy groups as determined by EDX. (4) Conclusion: The comparison between lumbar radiculopathy diagnoses in patients with clinically suspected pathology using MRI and EDX as diagnostic modalities did not yield statistically significant findings. MRI and EDX are complementary tests assessing different aspects in patients with suspected radiculopathy; degeneration of the structures supporting the spinal cord does not necessarily imply root dysfunction.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

This article explores the enduring mysteries of consciousness and the afterlife, two enigmatic topics that have fascinated humanity for ages. Despite extensive scientific efforts, the existence of an afterlife remains unproven, and understanding consciousness remains a significant challenge. The research introduces innovative hypotheses through simple thought experiments with empirical evidence and robust theoretical foundations. It delves into the complexities of consciousness, its relationship with the brain, and the need for interdisciplinary approaches encompassing physics, psychology, and philosophy. Boldly contemplating the probability of a continuous consciousness after death, the study argues that existing evidence strongly supports this idea. Beyond theoretical implications, it envisions practical outcomes, suggesting that insights into these mysteries could enhance human well-being and contribute to a more harmonious world. In summary, this article embarks on a quest to shed light on age-old questions about consciousness and the afterlife. Through fresh methodologies, it aims to provide new perspectives that could reshape our understanding of existence and inspire intellectuals to positive individual and societal advancements including psychological well-being and intelligence.

Symmetry concepts in parametrized dynamical systems may reduce the number of external parameters by a suitable normalization prescription. If, under the action of a symmetry group G, parameter space A becomes a (locally) trivial principal bundle, A ~ A/G x G, then the normalized dynamics only depends on the quotient A/G. In this way, the dynamics of fractional variables in homogeneous epidemic SI(R)S models, with standard incidence, absence of R-susceptibility and compartment independent birth and death rates, turns out to be isomorphic to (a marginally extended version of) Hethcote's classic endemic model, first presented in 1973. The paper studies a 10-parameter master model with constant and I -linear vaccination rates, vertical transmission and a vaccination rate for susceptible newborns. As recently shown by the author, all demographic parameters are redundant. After adjusting time scale, the remaining 5-parameter model admits a 3-dimensional abelian scaling symmetry. By normalization we end up with Hethcote's extended 2-parameter model. Thus, in view of symmetry concepts, reproving theorems on endemic bifurcation and stability in such models becomes needless.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

This paper presents a new methodology that provides the analysis of surface texture changes in areas adjacent to the volcano and its impact product of volcanic activity. To do this, algorithms from digital image processing such as the co-occurrence matrix and the wavelet transform are used. These methods are working on images taken by the Landsat satellite platform sensor 5 TM and Landsat 7 ETM + sensor, and implemented with the purpose of evaluating superficial changes that can warn of surface movements of the volcano. The results were evaluated by similarity metrics for grayscale images, and validated in two different scenarios that have the same type of eruption, but differ, essentially, in climate and vegetation. Finally, the proposed algorithm is presented, setting the parameters and constraints for implementation and use.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

The agronomic characteristics of Cenchrus purpureus were assessed through a randomized block experimental design with seven accessions (Taiwan grass, King grass, Elephant grass, Merkeron, CT-115, Purpule grass and Maralfalfa) as treatments and four replications research was carried out at the Instituto Tecnológico Superior de Tantoyuca, in 2019 and 2020, under rainfed conditions. Sowing density was established at 36 tillers in 25 m2. Green and dry matter yield, daily rates of dry matter accumulation in leaves, leaf/stem ratio, height, leaf area index and cutting frequency were assessed. Rainfall amount, temperature, relative humidity and global radiation levels were recorded to assess their effect on the evaluated variables. One-way ANOVA and multivariate analysis techniques, such as multiple linear regression (MLR), Clustering, and Principal component analysis (PCA) with the Statistica V7 software, were used. The leaf area index was greatest (p &lt; 0.05) on the dry season. Green and dry matter yield were greatest in Maralfalfa (p &lt; 0.05). Variation in the results is attributed to weather phenomena; nonetheless, Elephant grass and Maralfalfa showed the highest yields. Quality parameters must be evaluated to identify those grasses with the best attributes.

In the present-day digital landscape, websites have increasingly relied on digital marketing practices, notably search engine optimization (SEO), as a vital component in promoting sustainable growth. The traffic a website receives directly determines its development and success. As such, website owners frequently engage the services of SEO experts to enhance their website's visibility and increase traffic. These specialists employ premium SEO audit tools that crawl the website's source code to identify structural changes necessary to comply with specific ranking criteria, commonly called SEO factors. Working collaboratively with developers, SEO specialists implement technical changes to the source code and await the results. The cost of purchasing premium SEO audit tools or hiring an SEO specialist typically ranges in the thousands of dollars per year. Against this backdrop, this research endeavors to provide an open-source Python-based Machine Learning SEO software tool to the general public, catering to the needs of both website owners and SEO specialists. The tool analyzes the top-ranking websites for a given search term, assessing their on-page and off-page SEO strategies, and provides recommendations to enhance a website's performance to surpass its competition. The tool yields remarkable results, boosting average daily organic traffic from 10 to 143 visitors.

Engine Overheating is a condition where the engine temperature has increased above the working temperature. This analysis aims to analyze the damage, determine the factors causing the damage, identify corrective steps and prevent engine overheating. The inspection procedure is carried out by checking the cooling system's components, cylinder head, and cylinder block. Further analysis using a fishbone diagram to analyze the causes of engine overheating troubleshooting. Damage analysis results Engine overheating occurs because the thermostat is damaged, namely, the thermostat valve which cannot open when the temperature reaches the standard temperature (71oC), and also due to damage to the cylinder gasket which causes bubbles due to compression leaks and mixing of radiator coolant and oil. Repair steps are taken in the form of replacing damaged components with new ones. Preventive measures are taken by not using the unit on an over-running basis, checking coolant levels, carrying out daily checks properly and correctly, and carrying out preventive maintenance regularly.

The ACC feature when activated augments the engine performance in real-time. This article presents a novel methodology to predict the optimal adaptive cruise control set speed profile (ACCSSP) by considering all the effecting parameters. This paper investigates engine operating conditions (EOC) criteria to develop a predictive model of ACCSSP in real-time. We developed a deep learning (DL) model using the NARX method to predict engine operating point (EOP) mapping the vehicle-level vectors (VLV). We used real-world field data obtained from Cadillac test vehicles driven by activating the ACC feature for developing the DL model. We used a realistic set of assumptions to estimate the VLV for the future time steps for the range of allowable speed values and applied them at the input of the developed DL model to generate multiple sets of EOP’s. We imposed the defined EOC criteria on these EOPs, and the top three modes of speeds satisfying all the requirements are derived for each second. Thus three eligible speed values are estimated for each second, and an additional criterion is defined to generate a unique ACCSSP for future time steps. Performance comparison between predicted and constant ACCSSPs indicates that the predictive model outperforms constant ACCSSP.

Often, in biology, we are faced with the problem of exploring relevant unknown biological hypotheses in the form of myriads of combination of factors that might be affecting the pathway under certain conditions. Currently, a major persisting problem is to cherry pick the combinations based on expert advice, literature survey or guesses for investigation. This entails investment in time, energy and expenses at various levels of research. To address these issues, a search engine design was recently been developed, which showed promise by revealing existing confirmatory published wet lab results. Additionally and of import, the engine mined up a range of unexplored/untested/unknown combinations of genetic factors in the Wnt pathway that were affected by ETC-1922159 enantiomer, a PORCN-WNT inhibitor, after the colorectal cancer cells were treated with the inhibitor drug. As an example, MYC is known to upregulate PRC2 complex. PRC2 complex contains EZH2, which suppresses tumor suppressor genes via epigenetic modifications. MYC and HOXB8 are up regulated in colorectal cancer, however, the dual working mechanism of the same is not known. The in silico engine showed positioning which correctly approximates and assigns to this 3rd order combination of MYC-HOXB8-EZH2, pointing to the in vitro/in vivo down regulation by ETC-1922159. If the protein interaction of MYC-HOXB8 can be established and a study be done apropos EZH2, it will establish at in vitro/in vivo level, the in silico ranking also. The potential of this engine is immense given the problem faced in biology and other fields. Here we elucidate the R code to understand the mechanics of the search engine in a fluid manner for systems biologists. Though the search engine is in the developmental stage, we share the detailed mechanism of the working principles of the same as it can be generalized to problems in other fields.

The COVID-19 pandemic crisis has brought about unprecedented economic and social consequences worldwide. The implementation of isolation measures, including national and international travel restrictions, significantly affected contact-intensive sectors such as tourism. During this lockdown period, Information and Communication Technology (ICT) was crucial in maintaining connectivity and enabling remote activities. Governments across the world implemented discretionary measures to mitigate the crisis's adverse effects on economic activity. This paper aims to analyze whether the level of ICT adoption and the importance of tourism influence the fiscal policy efforts pursued by governments. Based on the results of a linear regression analysis for 154 countries, the findings suggest that in countries with higher international tourism receipts, the governments had to promote higher fiscal stimulus. At the same time, ICT development diminished the efforts of the fiscal policy response to the crisis since it facilitated economic resilience. The findings of this study can contribute to understanding how governments responded to the pandemic crisis and the factors that influenced their fiscal policy decisions.

(S)-1-Methyl-2-oxoimidazolidine-4-carboxylic acid 1 is an analog of (S)-pyroglutamic acid, a key component of naturally occurring peptide hormones and synthetic pharmaceutical candidates. Reaction of (S)-2-amino-3-(methylamino)propionic acid with COCl2 and aqueous NaHCO3 followed by ion exchange afforded 1, which was recrystallized from acetonitrile and then characterized by IR, 1H NMR, 13C NMR, polarimetry, elemental microanalysis, high resolution mass spectrometry and single crystal X-ray diffraction. The acid 1 crystallized in the orthorhombic chiral space group P212121 with cell constants a = 6.2275(4) Å, b = 8.3963(5) Å, c = 24.9490(14) Å. The X-ray crystal structure reveals that two distinct conformers of 1 occur at alternating positions within helices which are supported by hydrogen-bonding. Each molecule of 1 is linked to its two neighbors in the helix by a total of three hydrogen bonds and four molecules of 1 are contained within each turn of the helix. The pattern of hydrogen bonds illustrates a preference for the carboxylic acid group to act as a hydrogen bond donor and for the urea unit to be a hydrogen bond acceptor.

Academic and corporate research has been focusing on analyzing stock performances, financial markets, and investment strategies for decades. According to Lynch and Rothchild (1989), certain investments can be described as plays. In this work, the authors use the term for investments in value stocks, spin-offs, and turnarounds to analyze the long-term stock performance and risk-adjusted excess returns of up to five years for those stocks. Additionally, stocks with a supe-rior return performance are identified within an investment play based on low P/E and P/B mul-tiples. The study finds that value stocks, spin-offs, and turnarounds outperform the S&P 500 on average on a one-, three- and five-year investment horizon. The analysis of the three investment plays confirms earlier studies that investment plays constitute a profitable investment opportunity. Moreover, the research exemplifies that private investors could achieve an excess return (alpha) through a passive buy-and-hold investment strategy. Overall, the analysis provides a deeper in-sight into the long-term performance of value stocks, spin-offs, and turnarounds.

In the present paper, we introduced a quadratically convergent Newton’s like normal S2 iteration method free from the second derivative for the solution of nonlinear equations permitting 3 f'(x) = 0 at some points in the neighborhood of the root. Our proposed method works well 4 when the Newton method fails. Numerically it has been verified that the Newton’s like normal 5 S-iteration method converges faster than Fang et al. method [A cubically convergent Newton-type 6 method under weak conditions, J. Compute. and Appl. Math., 220 (2008), 409-412]. We studied 7 different aspects of normal S-iteration method. Lastly, fractal patterns support the numerical 8 results and explain the convergence, divergence, and stability of method.

Let R be a commutative ring with identity and S be a multiplicatively closed subset of R. The purpose of this paper is to introduce the concept of weakly S-primary ideals as a new generalization of weakly primary ideals. An ideal I of R disjoint with S is called a weakly S-primary ideal if there exists s∈S such that whenever 0≠ab∈I for a,b∈R, then sa∈√I or sb∈I. The relationships among S-prime, S-primary, weakly S-primary and S-n-ideals are investigated. For an element r in any general ZPI-ring, the (weakly) S_{r}-primary ideals are charctarized where S={1,r,r²,⋯}. Several properties, characterizations and examples concerning weakly S-primary ideals are presented. The stability of this new concept with respect to various ring-theoretic constructions such as the trivial ring extension and the amalgamation of rings along an ideal are studied. Furthermore, weakly S-decomposable ideals and S-weakly Laskerian rings which are generalizations of S-decomposable ideals and S-Laskerian rings are introduced.

Much of the debate on Plan S seems to concentrate on how to make toll access journals open access, taking for granted that existing open access journals are Plan S compliant. We suspected this was not so, and set out to explore this using DOAJ's journal metadata. We conclude that an overwhelmingly large majority of open access journals are not Plan S compliant, and that it is small HSS publishers not charging APCs that are least compliant and will face major challenges with becoming compliant. Plan S need to give special considerations to smaller publishers and/or non-APC-based journals.

Gedanken experiments illustrating exemplifications of the Landauer principle in the free falling Einstein elevator are treated. Double-well simplest information system embedded into the free falling elevator is addressed. Infinitesimal horizontal force applied to the particle m transfers it from position “0” to position “1”, emerging from the free falling double-well system confining mass m. When thermal noise is considered, the potential barrier of kBT should be surmounted for the erasing of one bit of information. Entropic forces arising in the free falling elevator are considered. The maximal change in the entropy of free-joint polymer chain attached to the free falling elevator is estimated as ΔSmax≅kB, and it is remarkably independent of the mass attached to the chain and the parameters of the chain itself. Free falling minimal Szilard engine is treated. The informational re-interpretation of the minimal Szilard process is shaped as follows: the energy kBTln2 necessary for erasing of 1 bit of information is spent for lifting up mass, whatever, is the value of this mass. Appropriate choice of frames enables elimination of gravity in the considered system; however elimination of the thermal noise (dissipation processes) by the same procedure is impossible.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

The genus Strophantus belongs to the Apocynaceae family of flowering plants which grows primarily in tropical Africa. The plants are widely used in traditional herbal medicine. S. sarmentosus, in particular, is used for the treatment of, e.g., joint pain and rheumatoid arthritis, wound infections, head lice, diarrhoea, snake bite, and eye conditions. Despite the widespread use, dedicated research characterizing bioactive plant components is scarce. Investigations focussed mainly on the cardenolides, because of their cardioactivity and historical use as cardiotonic. There are also studies concerning the antibacterial, antioxidant and anti-inflammatory activity of plant extracts. This review summarizes the present knowledge about the biochemical and analytical reserach on Strophantus, in general, and S. sarmentosus, in particular, and describes the current state-of-the-field based on the available sientific literature.

In this paper we investigate some properties of square-free numbers. In particular, we study a function that counts the number of square-free numbers no larger than the given number n. We show that this function has asymptotics consistent with the predictions of the Riemann hypothesis and use this to obtain new and better estimates of the density of square-free numbers. Finally, we present a well-known generalization of the concept of a square-free number to monoids and research on square-free factorizations.

Monolayered MoS₂ is energetically most stable when it has a 1H phase, but 1H to 1T phase transition (1H→1T) is easily realized by various ways. Even though magnetic moment is not observed during 1H1T, 0.049 µB/MoS₂ is obtained in local 1T phase; 75% 2H and 25% 1T phases are mixed in (2×2) supercell. Furthermore, non-negligible magnetocrystalline anisotropy (MCA) energy is occured. Most magnetic moment as well as MCA are originated by 1T phased Mo atom5 in the supercell, while electronic structures of other atoms are similar to non-magnetic. Due to this, magnetic/non-magnetic boundary is created in the monolayered MoS2. Our result suggests that MoS₂ can be applied for spintronics such as a spin transistor.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

We prove an analog of the removable singularity theorem for bounded harmonic functions on stratified sets. The harmonic functions are understood in the sense of the soft Laplacian. The result can become one of the main technical components for extending the well-known Poincaré–Perron’s method of proving the solvability of the Dirichlet problem for the soft Laplacian.

Cardiovascular disease (CVD) is the leading cause of death worldwide. Cardiac rehabilitation (CR) has proven to be effective in reducing the rate of recurrence and disease as secondary prevention (evidence-based intervention) in patients who have suffered from myocardial infarction (MI). CR is a multidisciplinary path in which the patient is followed pharmacologically, from a psychological, nutritional, nursing and physiotherapy point of view. Post-MI patients present a reduction in the performance of the diaphragm muscle, the main inspiratory muscle, and this condition can become a risk factor for further relapses or for the onset of heart failure. Despite the solidity of the international guidelines for CR, the latter are lacking in specifically indicating an evaluation and training path regarding the inspiratory muscles in post-MI patients who have not undergone cardiac surgery. The article reviews the information on the adaptation of the diaphragm post-MI and highlights the need for clearer indications for a rehabilitation process that gives importance to the diaphragm.