The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

To develop aryloxyphenoxypropionate herbicides with novel structure and improved activity, a total of twenty-eight novel quinazolinone–phenoxypropionate derivatives containing a diester moiety were synthesized and tested for herbicidal activity. The bioassay results in the greenhouse showed that QPEP-I-4 exhibited excellent herbicidal activity against E. crusgalli, D. sanguinalis, S. alterniflora, E. indica, and P. alopecuroides with inhibition rates >80% at a dosage of 150 g ha-1, and displayed higher crop safety to G. hirsutum, G. max, and A. hypogaea than the commercial herbicide quizalofop-p-ethyl. Studying of the molecular mode of action by phenotypic observation, membrane permeability evaluation, and transcriptomic analysis revealed that a growth inhibition of plant by QPPE-I-4 was the result from damage of plants biomembrane. The evaluation of ACCase activity in vivo indicated that QPPE-I-4 could inhibit ACCase and may be a new type of ACCase inhibitor. The present work demonstrated that QPPE-I-4 could serve as a lead compound for further developing novel AOPP herbicides.

: Schizophrenia and schizoaffective disorder are generally treated with second-generation antipsychotic drugs. These drugs are mostly D2 and 5-HT2A antagonists. They improve positive schizophrenia symptoms sufficiently well; however, they ameliorate negative schizophrenia symptoms and cognitive functions to a small extent. We review novel antipsychotic drugs exerting a partial agonism at dopaminergic and serotonergic receptors such as cariprazine, brexipiprazole and lumateperone. Besides, the mechanisms of actions of non-anti-dopaminergic antipsychotic drugs are pointed out. Updated neural networks are used to explain the mechanism of action of M4 and M1 receptor agonists, for example xanomeline combined with trospium or emraclidine, and trace-amine-associated receptor 1 agonists (TAAR1), for example ulataront. Phase 3 clinical trials of new third generation antipsychotic drugs are presented. Novel antipsychotic drugs with a partial agonism at D2 and D3 receptors improve positive and negative schizophrenia symptoms as well as cognitive symptoms better than second generation antipsychotic drugs. Besides, they are well tolerated. M4 and M1 receptor agonists, i.e. xanomeline combined with trospium or emraclidine, and TAAR1 agonists, i.e. ulataront, have promising results in clinical trials; they well improve negative schizophrenia symptoms and cognitive functions. Phase 3 clinical trials offer promising results for anti-dopaminergic and non-anti-dopaminergic novel antipsychotic drugs. These new non-anti-dopaminergic antipsychotic drugs better emend negative schizophrenia symptoms, and they better improve cognitive functions than second-generation antipsychotic drugs. Promising new antipsychotic drugs are cariprazine, brexipiprazole, lumateperone, ulataront, and xanomeline combined with trospium. Although phase 3 clinical studies are not yet completed, they showed a therapeutic effect superior to those achieved by second-generation antipsychotic drugs. They are tolerated very well, and they better treat negative schizophrenia symptoms and improve cognitive functions.

A suitable waste management strategy is crucial for a sustainable and efficient circular economy in the construction sector, and requires precise data on the volume of demolition waste (DW) gen-erated. Therefore, we developed an optimal machine learning (ML) model to forecast the quantity of recycling and landfill waste based on the characteristics of DW. A dataset comprising infor-mation on the characteristics of 150 buildings, demolition equipment utilized, and volume of five waste types generated (i.e., recyclable mineral, recyclable combustible, landfill specified, and landfill mix waste, and recyclable minerals) was constructed. ML models were developed to predict the quantities of such waste. Artificial neural network, decision tree, gradient boosting machine, k-nearest neighbors, linear regression, random forest (RF), and support vector regression were applied, and optimal models were derived via hyperparameter tuning. The RF model demonstrated superior performance. In both validation and test phases, the “recyclable mineral waste” and “recyclable combustible waste” models achieved accuracies of of 0.987 and 0.972, re-spectively. The “recyclable metals” and “landfill specified waste” models achieved accuracies of 0.953 and 0.858 or higher, respectively. Moreover, the “landfill mix waste” model exhibited an accuracy of 0.984 or higher. SHapley Additive exPlanations analysis highlighted floor area as the primary input variable influencing model performance. The type of equipment employed in demolition emerged as another crucial input variable impacting the volume of recycling and landfill wastes generated. The developed model can provide precise data on waste management, thereby facilitating the decision-making process for industry professionals.

Scale inhibitors are deployed as preventive and rejuvenation operation in oil and gas industry when production operations are under threat or menace of scale blockage. The application of scale inhibitors is carried out through a method known as squeezing. In general, the squeeze process is governed by inhibitor-rock interaction which is described by adsorption/desorption isotherm. Most reservoirs produce loose sand grains or fine sand which float and flow within the pore spaces along with the squeezed scale inhibitors. Hypothetical reports have shown that not all scale inhibitors pumped into the formation adsorb onto the formation rock. A number of factors (irreversible adsorption, pH changes, competing ions, concentration and temperature) have been considered to affect the adsorption and return profile of these scale inhibitors. This review work examines the performances of most common scale inhibitors used in the oil and gas production activities, theoretical application in reservoirs and how loose fine sand grains affect the adsorption and desorption characteristics of squeezed scale inhibitors. Additionally, presented were overviews of previous reports on fine sand production and migration of fine sands through formation pores in reservoirs.

Public safety and intelligent surveillance systems critically depend on anomaly behavior detection for effective monitoring. In real-world pedestrian detection scenarios, prevalent challenges such as missed detections, complex background interference, and small target sizes hinder accurate anomaly identification. To address these issues, this study introduces YOLO-ABD, a lightweight method for anomaly behavior detection that integrates small target detection and channel shuffling. This method employs YOLOv8n as the baseline model, incorporating a small target detection mechanism in the Head part and utilizing GSConv convolution in the Backbone to enhance perceptual capability. Additionally, the SimAM attention mechanism is integrated to mitigate complex background interference, thereby improving target detection performance. Evaluation on the IITB-Corridor dataset demonstrated mAP50 and mAP50-95 scores of 89.3% and 60.6%, respectively. Generalization testing on the street-view-gdogo dataset further highlighted the superiority of YOLO-ABD over advanced detection algorithms, underscoring its effectiveness and generalizability. With a relatively small parameter count, YOLO-ABD presents an excellent lightweight solution for pedestrian anomaly behavior detection.

Land cover data are important basic data for earth system science and other fields. Multi-source remote sensing images have become the main data source for land cover classification. There are still many uncertainties in the scale effect of image spatial resolution on land cover classification. Since it is difficult to obtain multiple spatial resolution remote sensing images of the same area at the same time, the main current method to study the scale effect of land cover classification is to use the same image resampled to different resolutions, however errors in the resampling process lead to uncertainty in the accuracy of land cover classification. To study the land cover classification scale effect of different spatial resolutions of multi-source remote sensing data, we selected 1 m and 4 m of GF-2, 6 m of SPOT-6, 10 m of Sentinel-2 and 30 m of Landsat-8 multi-sensor data, and explored the scale effect of image spatial resolution on land cover classification from two aspects of mixed image element decomposition and spatial heterogeneity. For the study area, we compared the classification obtained from GF-2, SPOT-6, Sentinel-2, and Landsat-8 images at different spatial resolutions based on GBDT and RF. The results show that (1) GF-2 and SPOT-6 had the best classification results, and the optimal scale based on this classification accuracy was 4–6 m; (2) the optimal scale based on linear decomposition depended on the study area; (3) the optimal scale of land cover was related to spatial heterogeneity, i.e., the more fragmented and complex was the space, the smaller the scale needed; and (4) the resampled images were not sensitive to scale and increase the uncertainty of the classification. These findings have implications for land cover classification and optimal scale selection, scale effects and landscape ecology uncertainty studies.

This empirical study investigates large urban park cooling effects on the thermal comfort of occupants in the vicinity of the main central park, located in Madrid, Spain. Data were gathered during hot summer days, using mobile observations and a questionnaire. The results showed that the cooling effect of this urban park of 140 ha area at a distance of 150 m is able to reduce temperature by an average of 0.63°C and 1.28°C for distances of 380 m and of 665 meters from the park. Moreover, the degree of the Physiological Equivalent Temperature (PET) index at a distance of 150 meters from the park is on average 2°C PET and 2.3°C PET less compared to distances of 380 m and 665 m, respectively. Considering distance from the park, the correlation between occupant Perceived Thermal Comfort (PTC) and PET is inverse. That is, augmenting the distance from park increases PET, while the extent of PTC reduces accordingly. The correlation between these two factors at the nearest and furthest distances from the park is meaningful (P-value <0/05). The results also showed that large-scale urban parks generally play a significant part in creating a cognitive state of high-perceived thermal comfort spaces for residents.

Due to the inherent limitations of a single viewpoint, reconstructing 3D human meshes 1 from a single image has long been a challenging task. While deep learning networks enable us to 2 approximate the shape of unseen sides, capturing the texture details of the non-visible side remains 3 difficult with just one image. Traditional methods utilize Generative Adversarial Networks (GANs) 4 to predict the normal maps of the non-visible side, thereby inferring detailed textures and wrinkles 5 on the model’s surface. However, we have identified challenges with existing normal prediction 6 networks when dealing with complex scenes, such as a lack of focus on local features and insufficient 7 modeling of spatial relationships.To address these challenges, we introduce EMAR—Enhanced 8 Multi-scale Attention-driven Single Image 3D Human Reconstruction. This approach incorporates 9 a novel Enhanced Multi-Scale Attention (EMSA) mechanism, which excels at capturing intricate 10 features and global relationships in complex scenes. EMSA surpasses traditional single-scale attention 11 mechanisms by adaptively adjusting the weights between features, enabling the network to more 12 effectively leverage information across various scales.Furthermore, we have improved the feature 13 fusion method to better integrate representations from different scales. This enhanced feature fusion 14 allows the network to more comprehensively understand both fine details and global structures 15 within the image. Finally, we have designed a hybrid loss function tailored to the introduced attention 16 mechanism and feature fusion method, optimizing the network’s training process and enhancing the 17 quality of reconstruction results.Our network demonstrates significant improvements in performance 18 for 3D human model reconstruction. Experimental results show that our method exhibits greater 19 robustness to challenging poses compared to traditional single-scale approaches.

This study focused on the development and implementation of an educational simulation program based on Korean Triage and Acuity Scale (KTAS) for nurses in emergency medical centers who completed KTAS training. We also examined its educational effects based on the evaluation of clinical decision-making ability, job satisfaction, and customer orientation. The study participants were 30 nurses in the emergency medical center of a general hospital. Data were collected from May 3 to 24, 2017, and analyzed using SPSS 22.0. There was a significant difference in the mean scores in clinical decision-making ability, job satisfaction, and customer orientation before and after simulation education. In other words, emergency nurses who received KTAS-based simulation education program improved their clinical decision making ability, job satisfaction, and customer orientation. Based on the results of this study, it is expected that it can be used for KTAS education, and it was found that simulation-based education is a useful learning method for triage nurses in emergency medical center.

Pepper leaf segmentation plays a crucial role in monitoring pepper leaf diseases in various backgrounds and ensuring the healthy growth of peppers. However, existing transformer-based segmentation methods suffer from computational inefficiency, excessive parameterization, and limited utilization of edge information. To tackle these challenges, we propose an adaptive multi-scale MLP framework, named AMS-MLP, which combines the multi-path aggregation module (MPAM) and the multi-scale context relation mask module (MCRD) to refine the object boundaries in pepper leaf segmentation. AMS-MLP consists of an encoder-based network, an adaptive multi-scale MLP (AM-MLP) module, and a decoder network. In the encoder network, the MPAM module effectively fuses five-scale features to generate a single-channel mask, improving the accuracy of pepper leaf boundary extraction. The AM-MLP module divides the input features into two branches: the global multi-scale MLP branch captures long-range dependencies between image information, while the local multi-scale MLP branch focuses on extracting local feature maps. Adaptive attention mechanism is designed to dynamically adjust the weights of global and local features. The decoder network incorporates the MCRD module into the convolutional layer, enhancing the extraction of boundary features. To verify the performance of the proposed method, we conducted extensive experiments on three pepper leaf datasets with different backgrounds. The results demonstrate mIoU scores of 97.39%, 96.91%, and 97.91%, as well as F1 scores of 98.29%, 97.86%, and 98.51%, respectively. Comparative analysis with U-Net and state-of-the-art models reveals that the proposed method dramatically improves the accuracy and efficiency of pepper leaf image segmentation.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

This study investigated the efficiency of scale-propellers, typically used on small drones. A scale-propeller is accepted as having a diameter of 7 to 21 inches. The Ukraine War has demonstrated the utility of relatively small, low-cost first-person view (FPV) drones, which are attritable. This investigation outlines the development of a MATLAB optimisation code, based on minimum induced loss propeller theory, which calculates the optimal chord and twist distribution for a chosen propeller operating in known flight conditions. The MATLAB code includes a minimum Reynolds number functionality, which provides the option to alter the chord distribution to ensure the entire propeller is operating above a set threshold value of Reynolds (&gt;100,000), as this has been found to be a transition point between low and high section lift-to-drag ratios. Additional functions allow plotting of torque and thrust distributions along the blade. The results have been validated on experimental data taken from an APC ‘Thin Electric’ 10” x 7” propeller, where it was found that both the chord and twist distributions were accurately modelled. The MATLAB code resulted in a 16% increase in the maximum propulsive efficiency. Further work will investigate a direct interface to SolidWorks to aid rapid propeller manufacturing capability.

The control of the fine particle emission from the coal-fired power plants has been a big challenge in china. Either the conventional electrostatic precipitator or the fabric filter has some shortages. The electrostatic precipitator is hard to keep high efficiency for the submicron particles. The fabric filter could keep high efficiency but with very high pressure drop. One solution is to combine them together. Several types of hybrid particle collectors (HPC) combining the electrostatic precipitator and the fabric filter together have been developed and applied in a number of projects in China. In recent years, numerical simulation technology has been widely used in the design of the collectors. In this paper, an unsteady numerical model is used to investigate the particle deposition characteristics in a scale hybrid collector. The fluid field is modeled by using incompressible Navier-Stokes equations with the RNG turbulence equations. The corona discharge is solved by using a finite volume method. The particle charging is modeled by using a filed-diffusing combined model. And an unsteady cake formation model is used to simulate the filtration process.

A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Existing methods of hyperspectral anomaly detection still face several challenges: 1) Due to the limitations of self-supervision, avoiding the identity mapping of anomalies remains difficult; 2) The ineffective interaction between spatial and spectral features leads to the insufficient utilization of spatial information; 3) Current methods are not adaptable to the detection of multi-scale anomaly targets. To address the aforementioned challenges, we proposed a blind spot network based on multi-scale blind spot convolution for HAD. The multi-scale mask convolution module is employed to adapt to diverse scales of anomaly targets, while the dynamic fusion module is introduced to integrate the advantages of mask convolutions at different scales. The proposed approach includes a spatial-spectral joint module and a background feature attention mechanism to enhance the interaction between spatial-spectral features, with a specific emphasis on highlighting the significance of background features within the network. Furthermore, we propose a preprocessing technique that integrates pixel shuffle down-sampling (PD) operation with spatial spectral joint screening to address the issue of anomalous identity map-ping and facilitate finite-scale mask convolution to adapt to the detection of more scale targets. The proposed approach was assessed on four real hyperspectral datasets comprising anomaly targets of different scales. The experimental results demonstrate the effectiveness and superior performance of the proposed methodology compared with nine state-of-the art methods.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

The impact of the agriculture net carbon effect is crucial for climate change mitigation, yet research on this topic in China is currently insufficient. In this study, the carbon balance ratio (CBR) is used to characterise the net carbon effect of agriculture, and the spatial Durbin model and threshold regression model were used to empirically analyse the CBR with a sample of 30 provincial-level regions in China from 2004 to 2019. The aim was to investigate the mechanism of the influence of the land management scale (SCALE) of farming on the CBR. The results of the study indicate that national farming generally has a net sink effect, with large changes in interannual fluctuations; the expansion of SCALE has an obvious role in increasing sinks and reducing emissions, and has a positive spatial spillover effect on CBR, with significant spatial heterogeneity. Furthermore, as the SCALE expands, the direction of the influence of rural residents’ income and education level on CBR changes in the opposite direction, showing a significant non-linear relationship characteristic. However, in most areas, the SCALE threshold has not yet been reached, suggesting that the improvement in education levels can still offset the negative impact of economic income growth in the short term. The study recommends paying attention to the role of farmers’ human capital, changing production methods, and implementing carbon peaking and carbon neutrality goals to enhance the net sink effect of the farming industry, which would be achieved by increasing land management scale.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

Molecular-scale density fluctuations at equilibrium produce cavities in a liquid and can be analyzed to shed light on the statistics of the number of molecules occupying observation volumes of increasing radius. An information theory approach led to the conclusion that these probabilities should follow a Gaussian distribution function. This prediction has been confirmed by computer simulations in different liquid models if the size of the observation volume is not large. The reversible work of cavity creation is exactly linked to the probability of finding zero molecules in a given observation volume. The Gaussian formula for the latter probability is scrutinized to arrive at the enthalpy and entropy changes associated with cavity creation. The reversible work of cavity creation has a purely entropic origin due to the solvent-excluded volume effect produced by the inaccessibility of a given region of the configurational space. The consequent structural reorganization of liquid molecules leads to exactly compensating enthalpy and entropy changes. These results are in line with those obtained in a direct statistical mechanical study by Lee.

The main objective of this study was to compare the removal efficiency of nutrients using Lactuca sativa, Medicago sativa and Phragmites australis in subsurface flow constructed wetlands with horizontal flow. In order to test water quality, fabricated reactors designed and the plants cultivated in the soil while their root were inside the wastewater. A long time study carried out from spring till end of autumn (9 months) in order to evaluate the difference in removal rate based on the seasonal changes. The highest removal rate was during summer which followed by spring and autumn. Thus, the effect of plants on the removal efficiency of organic matter (COD, BOD), TSS and nutrient (P and TN) appeared to be dependent on the seasonal growth. Phragmites australis the most sensitive species in order the removal of nutrient from wastewater.

Developing and utilising of underground space is an vital direction for urban growth. Underground commercial streets, as a significant component of underground space accommodating extensive human social activities, and consequently necessitate the creation of human-scale spaces. In the evolution of urban design development towards greater refinement, applying architectural theories and excessively subjective designs has resulted in a deficiency of human-centered design and a disordered spatial environment. This study merges environmental psychology and architectural theory to determine the appropriate length of spatial scale. Two experiments focusing on spatial perception evaluation were conducted using a virtual experimental platform that featured varying dimensions of spatial scale combinations. These quantified combinations were correlated with perception evaluation, and regression analysis was employed to identify appropriate scale ranges, which were superimposed on the range of length selection. Finally, the optimal length and scale combination for underground commercial street spaces were established, providing a reference for the human-centered design of these environments.

The rural communities are affected by gaseous emissions from intensive livestock production. Practical mitigation technologies are needed to minimize emissions from stored manure and improve air quality inside barns. In our previous research, the one-time surficial application of biochar to swine manure significantly reduced emissions of NH3 and phenol. We observed that the mitigation effect decreased with time during the 30-day trials. In this research, we hypothe-sized that bi-weekly reapplication of biochar could improve the mitigation effect on a wider range of odorous compounds using larger scale and longer trials. The objective was to evaluate the effectiveness of biochar dose and reapplication on mitigation of targeted gases (NH3, odor-ous VOCs, odor, GHGs) from stored swine manure on a pilot-scale setup over 8-weeks. The bi-weekly reapplication of the lower biochar dose (2 kg/m2) showed much higher significant percent reductions of emissions for NH3 (33% without & 53% with reapplication) and skatole (42% without & 80% with reapplication), respectively. In addition, the reapplication resulted in the emergence of statistical significance to the mitigation effect for all other targeted VOCs. Spe-cifically, for indole, the % reduction improved from 38% (p=0.47, without reapplication) to 78% (p=0.018, with reapplication). For phenol, the % reduction improved from 28% (p=0.71, without reapplication) to 89% (p=0.005, with reapplication). For p-cresol, the % reduction improved from 31% (p=0.86, without reapplication) to 74% (p=0.028, with reapplication). For 4-ethyl phenol, the percent emissions reduction improved from 66% (p=0.44, without reapplication) to 87% (p=0.007, with reapplication). The one-time 2 kg/m2 and 4 kg/m2 treatments showed similar effectiveness in mitigating all targeted gases, and no statistical difference was found between the dosages. The one-time treatments showed significant % reductions of 33% & 42% and 25% & 48% for NH3 and skatole, respectively. The practical significance is that the higher (one-time) biochar dose may not necessarily result in improved performance over the 8-week manure storage, but the bi-weekly reapplication showed significant improvement in mitigating NH3 and odorous VOCs. The lower dosages and the frequency of reapplication on the larger-scale should be explored to optimize biochar treatment and bring it closer to on-farm trials.

Since the beginning of the internet era, there has been an explosion of growth in structured data (such as numbers, symbols, and labels) as well as unstructured data (including images, videos, and text). Efficient and accurate mixed query of these two types of data is a key technology to achieve high-quality information retrieval, and it is also a major challenge that needs to be solved urgently in the industry. In this study, we employ an advanced Transformer model that combines strategies and fine-tuning techniques for multi-task learning. Specifically, the model is first pre-trained on a large-scale, general-purpose dataset to learn different types of data representations and basic language comprehension skills. After that, we fine-tuned the parameters of the model to better suit these specific data processing tasks for specific application scenarios, such as image annotation, video content analysis, and structured data query. At the heart of the model is the self-attention mechanism, which allows the model to automatically emphasize the important parts and ignore irrelevant information when processing the input data. In addition, we have introduced task-specific adaptation layers that are designed to add additional processing power to the original Transformer architecture, such as a semantic analysis layer for unstructured text data and a relational extraction layer for structured data. This combination of general pre-training and task-specific fine-tuning allows the model to flexibly process and integrate information from different data sources, improving processing efficiency and accuracy. Experimental results show that the model performs well in a variety of data processing tasks, significantly improves the accuracy and efficiency of information retrieval, and verifies the strong potential and adaptability of large language models in processing mixed data types.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

The globose scale (GS) (Sphaerolecanium prunastri Boyer de Fonscolombe) is a sucking insect that feeds on saps of wild apricot tree (Prunus armeniaca L.) in the Xinjiang Uygur Autonomous Region of northwestern China. It feeds on branches of wild apricot leading to poor growth, leaf yellowing and leaf drop, and sometimes mortality. Since the initial infestation in 2018, all the main valleys of wild apricot trees have been affected, but there is little research on the host’s physiological response to GS infestation. We measured the differences in growth between infested and non-infested wild apricots. The results showed that the diameter of shoot branches, the fresh weight, dry weight, length, width, area, and chlorophyll content of leaves, and the longitudinal diameter of fruit, were all significantly less for infested wild apricot trees than for un-infested wild apricot. The branch length of shoots, cross diameter, and weight of fruit also decreased, although the differences were not significant. Overall, GS infestation significantly reduced the growth of wild apricot trees, and may accelerate the damage by GS to wild apricot over time.

The objective of person re-identification (ReID) tasks is to match a specific individual across different times, locations, or camera viewpoints. The prevalent issue of occlusion in real-world scenarios affects image information, rendering the affected features unreliable. The difficulty and core challenge lie in how to effectively discern and extract visual features from human images under various complex conditions, including cluttered backgrounds, diverse postures, and the presence of occlusions. Some works have employed pose estimation or human keypoint detection to construct graph-structured information to counteract the effects of occlusions. However, this approach introduces new noise due to issues such as the invisibility of keypoints. Our proposed module, in contrast, does not require the use of additional feature extractors. Our module employs multi-scale graph attention for the reweighting of feature importance. This allows features to concentrate on areas genuinely pertinent to the re-identification task, thereby enhancing the model's robustness against occlusions. To address these problems, a model that employs multi-scale graph attention to re-weight the importance of features is proposed in this study, significantly enhancing the model’s robustness against occlusions. Our experimental results demonstrate that, compared to baseline models, the method proposed herein achieves a notable improvement in mAP on occluded data sets, with increases of 0.5%, 31.5%, and 12.3% in mAP scores.

Currently, the use of recycled waste plastic in road construction is not just considered ecofriendly but also considered advantageous for improving road performance over time. This research explores using recycled plastic bags, made of low-density polyethylene (LDPE), in asphalt mixtures to improve road performance and manage waste. The study aims to assess the effects of incorporating different amounts of shredded waste plastic into asphalt mixes and determine the optimal percentage. The aggregate used was obtained from Sargodha quarry Pakistan and asphalt used was 60/70 grade obtained from national refinery limited Pakistan. Using the Marshall mix design, the optimum bitumen content (OBC) was found to be 4.5% of the asphalt mix weight. Thirty samples were tested with waste plastic proportions of 6%, 8%, 10%, 12%, and 14% of OBC weight, along with a standard mix. Tests on stability, bulk density, flow, and air voids showed that a 10% plastic content significantly enhances asphalt performance, increasing stability by around 25%. The study recommends using 10% plastic by OBC weight in asphalt mixes for better performance and suggests further research on optimal incorporation techniques of waste materials in asphalt mixtures.

Three-dimensional (3D) geological modeling technology offers intricate geological information services and technical support for the research of urban geological conditions and their evolutionary mechanisms. It further facilitates the analysis of environmental geological problems, encompassing their distinguishing features and genetic mechanisms. The precision of such three-dimensional models is predominantly influenced by the caliber of modeling data, the chosen modeling methodologies, and the intricacy of the modeled geological objects. This research, exemplified by the three-dimensional geological structure modeling of the Wuhan metropolitan development area, aims to explore a comprehensive three-dimensional modeling framework for urban geology, particularly in scenarios with large-scale and complex geological conditions. This study holds significant technical value in enhancing the application of 3D geological modeling, as well as practical importance for urban geological investigations and research.

Civic participation is of great significance to urban management decision-making. In order to facilitate citizens to participate in city management decision-making, this paper proposes a large-scale group decision-making (LSGDM) method based on multi-granular probabilistic linguistic preference relations (MG-PLPRs). First, each decision maker selects a language terms set from the multi-granularity language terms set to represent individual preference relations and the MG-PLPRs are obtained by statistical calculation to represent sub-group’s preferences information. Then, an optimization model based on the expected consistency of PLPR and consensus measure of groups is established to achieving consensus reaching processes, which can ensure satisfactory individual consistency and group consensus. Finally, the validity and applicability of the proposed method is verified by a case of a city "shared garden" site selection with the participation of citizens.

Laser-targeted weeding methods further enhance the sustainable development of green agriculture, with one key technology being the improvement of weed localization accuracy. Here, we propose an improved YOLOv8 instance segmentation based on bidirectional feature fusion and deformable convolution (BFFDC-YOLOv8-seg) to address the challenges of insufficient weed localization accuracy in complex environments with resource-limited laser weeding devices. Initially, by training on extensive datasets of plant images, the most appropriate model scale and training weights are determined, facilitating the development of a lightweight network. Subsequently, the introduction of the Bidirectional Feature Pyramid Network (BiFPN) during feature fusion effectively prevents the omission of weeds. Lastly, the use of Dynamic Snake Convolution (DSConv) to replace some convolutional kernels enhances flexibility, benefiting the segmentation of weeds with elongated stems and irregular edges. Experimental results indicate that the BFFDC-YOLOv8-seg model achieves a 4.9% increase in precision, an 8.1% increase in recall rate, and a 2.8% increase in mAP50 value to 98.8% on a vegetable weed dataset compared to the original model. It also shows improved mAP50 over other typical segmentation models such as Mask R-CNN, YOLOv5-seg, and YOLOv7-seg by 10.8%, 13.4%, and 1.8%, respectively. Furthermore, the model achieves a detection speed of 24.8 FPS on the Jetson Orin nano standalone device, with a model size of 6.8MB that balances between size and accuracy. The model meets the requirements for real-time precise weed segmentation, suitable for complex vegetable field environments and resource-limited laser weeding devices.

Questions：SAP in mountainous cities of China serve as crucial carriers for species and wild food, constituting potential green infrastructure. These patches should be recognized as locally specific resources. This study investigates the transformation characteristics of the landscape patterns of SAP, along with their elements, across urban-rural gradients, providing foundational support for the planning of conservation and utilization strategies. Location: Yongchuan area of Chongqing in southwest China. Methods: The study investigated urban-rural gradient-based transformation of SAP. A four-direction transect space was selected and divided into uniform sample squares. Fragstats 4.3 calculated the landscape index of SAP, and Spearman correlation coefficients in SPSS were used to evaluate the influence of landform and artificial factors on agroforestry patch transformation. Results: 1) Patch area (PA), Plaque density (PD), and CLUMPY of SAP systematically transform, showing increased SAP areas and higher connectivity with greater distance from the city, resulting in reduced patch fragmentation. However, Edge density (ED) and Largest plaque index (LPI) exhibit irregular transformation patterns. 2) With increased distance from the city, woodland patch area and connectivity increase, leading to decreased fragmentation, dispersal, and lower fractal dimensions. Conversely, Cultivated land follows the opposite trend. garden land patch area, fractal dimension, fragmentation, and dispersal all increase, while connectivity decreases. 3) Landscape pattern transformations of SPA are significantly influenced by artificial factors. Woodland patches are influenced similarly by landform and artificial factors. In contrast, cultivated land and garden land patches are more significantly impacted by artificial factors. Conclusions: SAP exhibit differentiated conservation and utilization measures across urban-rural gradients. Small patches located far from urban centers may benefit from systematic conservation measures to prevent further fragmentation and erosion in peri-urban areas.

Background: Ice formation on power transmission lines presents significant risks, including structural damage and power outages. Traditional methods for detecting ice on these lines have limitations, particularly in challenging environmental conditions. This study aims to enhance ice detection accuracy by introducing a novel image segmentation and edge detection methodology using improved multi-scale Retinex and advanced morphological operations. Method: The proposed method integrates multi-stage image processing techniques, including image enhancement, grayscale conversion, thresholding, segmentation, object isolation, and edge detection. High-resolution binocular cameras were used to capture images of ice formations on transmission lines. The effectiveness of the method was assessed through a series of metrics, including accuracy, sensitivity, specificity, and precision, and compared with existing methodologies. Results: The proposed method demonstrated superior performance in both ice detection and thickness measurement. The method effectively identified and isolated ice formations under various conditions with an average accuracy of 98.35%, sensitivity of 91.63%, specificity of 99.42%, and precision of 96.03%. Additionally, the analysis of ice thickness measurements further highlighted the method’s accuracy, with a notably low root mean squared error (RMSE) of 1.20 mm and mean absolute error (MAE) of 1.10 mm, along with a strong R-squared value of 0.95. These statistical metrics show that the proposed method not only outperforms previous methods in consistency and alignment with manual measurements but also stands out as the most reliable option for tasks requiring precise measurements, offering significant advancements in accuracy and reliability over existing methodologies. Conclusions: The enhanced image segmentation and edge detection approach provides a more accurate and reliable method for monitoring ice formations on power transmission lines.

Integrating ecosystem services (ESs) to delineate ecological functional zones (EFZs) is a fundamental work in terrestrial spatial planning and ecosystem management. However, existing studies have largely overlooked the refinement of EFZs at local scales, which hinders targeted and multi-scale ecosystem management. This study introduced a "two-step refinement zoning method" to address this gap, first using the self-organizing feature mapping method to delineate EFZs based on ESs at a township scale, and then applying hotspot overlay analysis to identify hotspots of dominant ESs within EFZs at a village scale. By overlaying the outcomes of these two steps, EFZs can be further graded by designating villages with hotspots of dominant ESs as level I and those without as level II. The proposed method was applied in Wuhan City, dividing it into five types of EFZs with different ESs combinations and land use compositions. Furthermore, 5.23% of villages were identified as Level I of EFZs, serving as advantageous areas of dominant ESs in the study area. On this basis, diversified management strategies and conservation priorities were proposed. This study provides a theoretical and methodological reference for terrestrial spatial planning and sustainable ecosystem management.

The aim of present study was to assess the microbiological quality of eight traditional meat products (black pudding, white brown, baked pate, roasted pork, raw smoked ham, smoked steamed sausage, raw smoked bacon, raw smoked loin) manufactured by polish farmers in the Lodz region. A total of 37 samples were collected and analyzed twice: within 24 h after purchase from manufactures and after 7 days of storage. Mesophiles, lactic acid bacteria (LAB), Enterobacteriaceae, presence of Listeria monocytogenes and Salmonella spp. were determined. The counts of isolated microorganisms varied depending on the product type and manufacturer. Mesophiles and lactic acid bacteria constituted the main microflora in the tested meat products. Enterobacteriace value was below detection limit in the most samples. The highest mean bacteria counts (mesophiles, LAB and Enterobacteriace) during storage were estimated in black pudding, followed by smoked steamed sausage and white brown. In opposite, the lowest mean bacteria levels were in baked pate and roasted pork. The obtained results showed significant influence of storage time on the mean number of mesophiles and LAB in the meat samples. Negative results for Salmonella spp. and Listeria monocytogenes were observed during 7 days of storage, indicating the safety of the studied meat products.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

This study used Dutch potatoes at the end of dormancy as the material to explore the impact of menthol (0.2 and 0.5 g/kg based on potato mass) treatment on sprouting inhibition and potato quality. The findings revealed that a menthol concentration of 0.5 g/kg effectively inhibited potato tuber sprouting and significantly reduced glucoside alkaloids production. After a storage period of 15 days, the sprouting percentage and glucoside alkaloids content of potatoes treated with 0.5 g/kg menthol were observed to be significantly lower at 4.17% and 68.63 mg/kg, respectively, compared to the control group which exhibited values of 100% and 282.01 mg/kg, respectively (P < 0.05). Throughout the storage period, 0.5 g/kg of menthol promoted respiration, reduced malondialdehyde production in potatoes, inhibited polyphenol oxidase activity, and slowed down tissue browning. Additionally, it mitigated the decline in starch and soluble protein content, inhibiting the accumulation of reducing sugars.

Existing scales assessing family relations are usually quite long. Our aim was to develop and validate the Family Functioning and Cohesion Scale (FFCS), a self-reported short instrument consisting of 14 items. The validation of the FFCS was based on its administration through an online platform to 481 subjects living in 46 different countries around the world. Cronbach's alpha was 0.85 (ranging from 0.83 to 0.86 if any one item was deleted), signifying high internal consistency. The scale can be considered as a sole factor based on its high consistency, while factor analysis produced three factors corresponding to “communication”, “anger/resentment/aggression” and “values and beliefs”. Test-retest reliability correlation coefficient was found to be 0.88 at a 2-week interval. As far as external validity is concerned, the correlation coefficient of the FFCS with the General Functioning subscale of the McMaster Family Assessment Device (FAD) was 0.83. The high measures of consistency, reliability, and validity of the FFCS, combined with its short length, make it an invaluable tool for use in research as well as in any professional dealing with families in the clinical fields of psychiatry, psychology, social work or any other relevant specialty.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.

Most of the pore-scale imaging and simulations of non-Newtonian fluid are based on the simplifying geometry of network modeling and overlook the fluid rheology and heat transfer. In the present paper, we developed a non-isothermal and non-Newtonian numerical model of the flow properties at pore-scale by direct simulation of the 3D micro-CT images using a Finite Volume Method (FVM). The numerical model is based on the resolution of the momentum and energy conservation equations. Owing to an adaptive meshing technique and appropriate boundary conditions, rock permeability and mobility are accurately computed. A temperature and concentration-dependent power-law viscosity model in line with the experimental measurement of the fluid rheology is adopted. The model is first applied at isothermal condition to 2 benchmark samples, namely Fontainebleau sandstone and Grosmont carbonate, and is found to be in good agreement with the Lattice Boltzmann method (LBM). Finally, at non-isothermal conditions, an effective mobility is introduced that enables to perform a numerical sensitivity study to fluid rheology, heat transfer, and operating conditions. While the mobility seems to evolve linearly with polymer concentration, the effect of the temperature seems negligible by comparison. However, a sharp contrast is found between carbonate and sandstone under the effect of a constant temperature gradient. Besides concerning the flow index and consistency factor, a good master curve is derived when normalizing the mobility for both the carbonate and the sandstone.

Sustainable soil quality management is one of the most important approaches in ensuring high agricultural productivity and safe quality produce. With the current rising application of inorganic fertilizers and chemical pesticides, degradation of agricultural soils is becoming a global phenomenon, attracting attention of many researchers. The present study hypothesized that with the increasing chemical pesticide and fertilizer application under various cropping systems, there is potential for increased toxicity of heavy metals residues above background concentrations and their associated complexes and intermedia transfer between environmental compartments in large-scale farms in Kenya. Using standard methods, 204 soil samples collected from five distinct cropping systems were analyzed for PH, Electrical Conductivity, exchangeable base cations (Na+, Mg2+, K+, Ca2+), Cu, Pb, Zn, Cd, Fe, Cr, Total Organic Carbon and Total N and data analyzed using Genstart, version 23.1. The concentrations of Zn, Cu, Pb and Fe were lower than the globally acceptable levels hence less soil pollution threat (NPI&lt;1). However, Cd concentration exceeded permitted levels (NPI&gt;1). Among the cropping systems considered, Maize and sugarcane cropping systems were the most susceptible to heavy metal pollution. In conclusion, the rank order of the pollution potential associated with heavy metal contamination in the study area is Cd&gt;Zn&gt;Pb&gt;Cu&gt;Cr&gt;Fe.

This study describes a novel method for grading pathological sections of gliomas. Our own integrated hyperspectral imaging system was employed to characterize 270 bands of cancerous tissue samples from microarray slides of gliomas. These samples were then classified according to the guidelines developed by the World Health Organization, which define the subtypes and grades of diffuse gliomas. We explored a hyperspectral feature extraction model called SMLME-Resnet using microscopic hyperspectral images of brain gliomas of different malignancy grades. The model combines the channel attention mechanism and multi-scale image features to automatically learn the pathological organization of gliomas and obtain hierarchical feature representations, effectively removing the interference of redundant information. It also completes multi-modal, multi-scale spatial and spectral feature extraction to improve the automatic classification of glioma subtypes. The proposed classification method demonstrated high average classification accuracy (>97.3\%) and Kappa coefficient (0.954), indicating its effectiveness in improving the automatic classification of hyperspectral gliomas. The method is readily applicable in a wide range of clinical settings, offering valuable assistance in alleviating the workload of clinical pathologists. Furthermore, the study contributes to the development of more personalized and refined treatment plans, as well as subsequent follow-up and adjustment of treatment, by providing physicians with insights into the underlying pathological organization of gliomas.

In the ground-based infrared optical remote sensing system, the target signal is very weak due to the dynamic strong light background and the movement of small and small targets. In order to improve the limit detection capability, the background suppression and target enhancement methods are required to be more suitable for this scene. To solve this problem, we first analyze the image features in the current scene, and propose a more perfect point target and noise model. Then, we propose a new WY distribution function based on the Fermi Dirac distribution function, and propose an anisotropic filtering method based on this function, and further suppress the back-ground through the difference results of two steps. Then, based on the distribution function, we further designed an energy concentration accumulation strategy in 9 scale directions, through which the SNR of the target is effectively improved and the suppression ability of the background is enhanced. Through quantitative and qualitative experimental analysis, compared with the same type of algorithms, the proposed method has better robustness against extremely weak targets and dynamic backgrounds.

Exploring the effect of the sample size on the estimation accuracy of airborne LiDAR forest attributes in a large-scale area can help in optimizing the technical application scheme of operational ALS-based large-scale forest stand inventories. In our study, sample datasets composed of different sample plots were constructed by repeated sampling from 1003 sample plots in a subtropical study area covering 2376 × 103 km2. Sixteen multiplicative power models were built in each forest type consisting of four forest attributes. Through these models, the variations of standard deviation (SD) and coefficient of variation (CV) of R2 and rRMSE of forest attribute estimation models for different quantity levels of sample plots were also analyzed. The results showed that, first, when the sample size increased from 30 to the top limit, the SD of the forest attributes and LiDAR variables showed a decreasing trend. Second, as the sample size increased, the rRMSE of the 16 forest attribute estimation models gradually decreased, while the R2 gradually increased. Third, when the sample size was small, both the SD of R2 and rRMSE of the models were large, and the SD of R2 and rRMSE gradually decreased as the sample size increased. In 50 models conducted for each attribute at the same sample size, for the mean standard deviations of forest attributes, the ten best performing models were lower than those of the total 50 models, and the worst ten models were the opposite. When the sample size increased, the accuracy of each forest attribute estimation model for each forest type gradually improved. The variation of forest attributes and the LiDAR variable of the construction model are critical factors that affect the model’s accuracy. To efficiently apply airborne LiDAR in order to survey large-scale subtropical forest resources, the sample size of the Chinese fir forest, pine forest, eucalyptus forest, and broad-leaved forest should be 110, 80, 85, and 70, respectively.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

This paper presents geometric analyses of welded frames after free relaxing and vibratory stress relief (VSR). Respected frames were tested components of a prototype packaging machine. Two types of relaxation were carried out to remove stresses introduced as a result of welding process. One of the frame was subjected to free relaxing, while the other one to accelerated vibration relaxing. Detection of the frame geometry changes was performed using a photogrammetric system. In addition, an evaluation of the geometry change was conducted for fifteen variants of steel frame support. A comparative analysis of the geometric deviations of the frames after free and vibratory stress relief confirmed the assumption that the frame after vibration stress relief better reproduces the nominal dimensions. Nevertheless, it should be emphasized that after vibratory stress relief the frame is not subject to further deformation, which is a desirable effect. In the case of free relaxing, the frame undergoes dimensional changes in a random manner. In summary, carrying out accelerated vibratory stress relief allows control of spontaneous dimensional changes in the designed frame of a packaging machine resulting from spontaneous relaxation of stresses arising from the welding process. The shortening of the relaxation process of the welded frame is also an unquestionable advantage.

While the number of publications on wine and health is steadily increasing, ranging from molecular level to epidemiological studies, often with contradictory results, little attention has been given to an holistic approach. In this review some unusual concepts are considered, such as phytocomplex, vehicle and the Matrix effect. As an example, three mono/polyphenols present in wine, Tyrosol, Hydroxytyrosol and Resveratrol, have been selected and the consequences of respecting, disregarding or ignoring the Matrix effect are shown. Underestimation of the wine Matrix effect could lead to deceiving results, as in the case of de-alcoholized wine or wine-compound-based nutritional supplements,or in emphasizing a single component toxic activity, in this case alcohol, ignoring the specific protective action at molecular level of other compounds (polyphenols) present in the same Matrix. The dark side of Matrix effect is also discussed. It is suggested that specificity of wine should be always taken in consideration by public health Authorities.

The rapid development and integration of Autonomous Mobile Robots (AMRs) have 1 revolutionized industries by enhancing automation capabilities. A critical challenge in this evolution 2 is achieving effective navigation and obstacle avoidance, which are essential for deploying AMRs 3 seamlessly in varied environments. This paper presents a detailed exploration of AMR navigation 4 and obstacle avoidance advancements through the application of reinforcement learning, specifically 5 focusing on small-scale Sri Lankan manufacturing facilities. The study demonstrates the effectiveness 6 of Q-learning in managing dynamic obstacles within a factory environment. The AMR successfully 7 avoided obstacles in 36 out of 50 test runs, achieving a 72% success rate, and maintained an average 8 distance of 12 cm from each obstacle, underscoring the algorithm’s precision in maintaining safe nav- 9 igation paths while dynamically adapting to environmental changes. The continuous monitoring by 10 ultrasonic sensors, combined with iterative learning, enabled the robot to refine its decision-making 11 process and efficiently navigate through the environment. This paper also provides a comprehensive 12 examination of conventional methods, tracing their historical development and assessing their role in 13 addressing real-world challenges. The results highlight the significant improvements brought by rein- 14 forcement learning, particularly when integrated with sensor fusion and motor control technologies, 15 to enhance navigation and dynamic object collision avoidance. The study involves developing an 16 AMR prototype, refining algorithms, and assessing system performance in controlled environments. 17 By automating material transportation and addressing operational constraints in manufacturing 18 settings that predominantly rely on manual labor, this paper advances the practical deployment of 19 AMRs. Additionally, it discusses ethical considerations, potential limitations, and the importance 20 of real-world validation, offering valuable insights for the future development and integration of 21 autonomous mobile robotics in dynamic industrial environments.

Earth's global surface temperature shows variability on an extended range of temporal scales and satisfies an emergent scaling symmetry. Recent studies indicate that scale invariance is not only a feature of the observed temperature fluctuations, but an inherent property of the temperature response to radiative forcing, and a principle that links the fast and slow climate responses. It provides a bridge between the decadal- and centennial-scale fluctuations in the instrumental temperature record, and the millennial-scale equilibration following perturbations in the radiative balance. In particular, the emergent scale invariance makes it possible to infer equilibrium climate sensitivity (ECS) from the observed relation between radiative forcing and global temperature in the instrumental era. This is verified in ensembles of Earth system models (ESMs), where the inferred values of ECS correlate strongly to estimates from idealized model runs. For the range of forcing data explored in this paper, the method gives best estimates of ECS between 2.3 and 3.4 K.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Background/Objectives: Endocrine disruptors are ubiquitous agents in the environment and are present in everyday consumer products. These agents can interfere with the endocrine system, and subsequently the reproductive system, especially in pregnancy. Increasing research has been conducted to discover and describe the health effects of these agents on humans, including pregnant women, their fetuses, and the placenta. This review discusses prenatal exposure to various endocrine disruptors focusing on Bisphenols, Phthalates, Organophosphates, and Perfluoroalkyl substances, and their effects on pregnancy and fetal development. Methods: We reviewed the literature via PubMed and EBSCO databases and included the most relevant studies. Results: Our findings reveal that several negative health outcomes were linked to endocrine disruptors. However, despite the seriousness of this topic and the abundance of research on these agents, it remains challenging to draw strong conclusions about their effects from the available studies. This does not allow for strong, universal guidelines and might result in poor patient counseling and heterogeneous approaches to regulating endocrine disruptors. Conclusion: The urgency of the matter calls for urgent efforts, as more studies are needed in this realm, to protect pregnant patients ultimately and in the long term, society.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

Background: People with Down syndrome (DS) have a trisomy of chromosome 21 and marked deficits in verbal memory but relatively preserved visuospatial perception. Verbal memories are related to semantic knowledge. Little is known about the organization of semantic knowledge in people with DS, which was the aim of this study. Aims: The extent of false memory in people with DS was examined. Possible differences in the number of false memories induced by nominal and verbal themes were examined. Methods and Procedures: In the study phase, ten word lists with semantically related associates were presented. In the recognition phase, participants made judgments on whether each word had been represented previously as semantically related lures, old words, and semantically unrelated new words. Outcomes and Results: Differences in the processing of nominal and verbal theme-related lures were observed among people with DS. When processing nominal theme-related lures, people with DS showed delayed false positives. When processing verbal theme-related lures, people with DS showed no differences compared to controls. Similar patterns have been observed in people with DS when processing nominal theme-related associates and verbal theme-related associates. People with DS have delayed recognition of associates. When processing unrelated words, they showed significantly higher false positives than controls for both nominal and verbal eliciting themes. Further analyses of the themes revealed differences in false positives across syntactic categories among groups. Conclusions and Implications: People with DS showed a delayed recognition of associates and deviance in recognizing unrelated words in the nominal and verbal theme categories. People with DS were delayed in terms of nouns, but deviated with verbs in associated and unrelated words. Additionally, people with DS showed distinct patterns in processing five nominal lures and three verbal lures, suggesting that they formed false memories differently based on distinct syntactic categories. Thus, it was concluded that people with DS develop a deviant semantic structure. Category-based interventions for people with DS should be implemented in order to improve their semantic knowledge through lexical connections.

Temperature Cycle Induced Deracemization (TCID) offers a promising approach to obtain enantiopure solids from racemic mixtures. By combining rapid racemization in solution and temperature swings, homochirality is theoretically achieved. Despite theoretical expectations of doubled yields compared to traditional chiral separation methods, such as in Preferential Crystallization, experimental validation remains lacking. We applied TCID to (1-(4-chlorophenyl)-4,4-dimethyl-2-(1H-1,2,4-triazol-1-yl) pentan-3-one) (Cl-TAK), introducing a post-TCID cooling step to enhance yield and a washing step to augment enantiopurity. This refinement yielded an 89.8% mass yield with 99.1% enantiomeric excess in the crystal phase (c.e.e.) within 24 hours on an 8.75g scale, showcasing improved performance with insignificant process duration extension. Additionally, we explored the stochasticity of deracemization, observing the development from low initial crystal enantiomeric excesses(1-6% c.e.e0) at a 2.5 g scale. Kinetic analysis revealed that a 2% c.e.e0 effectively mitigates chiral flipping risks and induction time in our system. Our study underscores the potential for reduced initial c.e.e. to expedite deracemization and presents a straightforward method to optimize yield and purity, facilitating industrial application.

Small scale carp polyculture plays a key role for food supply in Bangladesh, however, factors including water pollution, limited infrastructure and inadequate disease management hinder its sustainability. This paper reports on a survey of 231 farmers across the 6 major carp producing regions in Bangladesh, analyzing factors including, farmers’ social aspects, farm characteristics, information on disease and approaches adopted to combat them, and biosecurity practices. Almost half (46.8%) of the farms surveyed experienced disease in carp species, with clear regional variations. Eighty four percent of farms reported carp mortalities during disease outbreak, with an average mortality level 10.23±11.81%. Clinical signs during outbreaks lasted between a week and a month, and there was a peak in disease outbreaks in two seasonal periods between June to July and October to December. Disease incidence was related to a range of factors including the farmer experience, ponds/farm type, stocked species, and biosecurity practice. A combination of disinfecting measures during pond preparation and measures during stocking, including discarding fingerling transport water off-farm, fingerling disinfection and check the health of fingerlings before stocking significantly reduced disease occurrence. Treatments involving the antibiotics, ciprofloxacin, erythromycin, and azithromycin were reported as ineffective, raising concerns about non-prudent use, inadequate dosing (perhaps without appropriate veterinary guidance) and the potential for further driving antimicrobial resistance in the environment. The research unveils a concerning pattern of disease high disease incidence across small-scale carp farms in Bangladesh and the significant potential for disease spread highlights the need for responsible disposal practices. The study emphasizes the need for improving training and awareness programs are vital for addressing biosecurity and disease management challenges, ensuring sustainable aquaculture and community well-being.

Purpose of research was to determine changes in optical quality for monthly disposable soft contact lenses (SCL) wearers with new and monthly worn SCL. Retinal straylight was assessed in SCL wearers using a C-Quant straylight meter. The study included 33 participants (age 22 ± 1.4 years) who wore monthly disposable silicone hydrogel contact lenses. Measurements were taken with month-old SCL that had been worn for no more than 4 hours. Participants then replaced the old lenses with new ones. After a 15-minute adaptation period, straylight measurements were taken with the new SCL. A questionnaire was administered to all participants, inquiring about vision complaints and the type of contact lens material used. The decimal logarithm of the stray-light parameter, log(s), was notably higher with month-old SCL (log(s) = 0.97±0.17) than with brand-new SCL (log(s) = 0.86±0.15), p < 0.001. The average increase in retinal straylight after a month of SCL use was log(s) = 0.11 ± 0.08. The questionnaire revealed that 35% of participants observed a reduction in visual quality after wearing the contact lenses for a month. Results showed that monthly disposable soft contact lenses could reduce visual quality when scheduled replacement time has been reached.

The repeated application of herbicides has led to the development of herbicide resistance. Models are useful for identifying key processes and understanding the evolution of resistance. This study developed a spatially explicit model at a landscape scale to examine the dynamics of Lolium rigidum populations in dryland cereal crops and the evolution of herbicide resistance under var-ious management strategies. Resistance evolved rapidly under repeated herbicide use, driven by weed fecundity and herbicide efficacy. Although fitness costs associated with resistant plants re-duced resistance evolution, they did not affect the speed of spread. The most effective strategies to slow resistance involved diversifying cropping sequences (e.g., crop rotation) and the herbicide applications (e.g., rotating different herbicide modes of action). Pollen flow was the main disper-sal vector, with seed dispersal also contributing significantly. Strategies limiting seed dispersal effectively decreased resistance spread. However, the use of a seed-catching device at harvest could unintentionally enrich resistance in the area. It would be beneficial to optimise the move-ment of harvesters between fields. The model presented here is a useful tool that may assist in the exploration of novel management strategies within the context of site-specific weed management at the landscape scale, as well as in the advancement of our understanding of resistance dynamics.

Pigmented corn is a gramineae food of great biological, cultural and nutritional importance for many Latin American countries, with more than 250 breeds in the American continent. It confers a large number of health benefits due to its diverse and abundant bioactive compounds. In this narrative review we decided to organize the information on the nutrients, bioactive compounds and phytochemicals present in pigmented corn, as well as their effects on human health. Phenolic compounds and anthocyanins are some of the most studied and representative compounds in these grasses, with a wide range of health properties, mainly the reduction of prooxidant molecules. Carotenoids are a group of molecules belonging to the terpenic compounds, present in a large number of pigmented corn breeds, mainly the yellow ones, whose biological activity incorporates a wide spectrum. Bioactive peptides can be found in abundance in corn, having very diverse biological effects that include analgesic, opioid, antihypertensive, etc. activity. Other compounds with biological activity found in pigmented corn are resistant starches, some fatty acids, phytosterols, policosanols, phospholipids, ferulic acid and phlobaphenes, as well as a great variety of vitamins, elements, and fibers. This review aims to disseminate and integrate the existing knowledge on compounds with biological activity in pigmented corn, in order to promote their research, interest and use by scientists, nutrition professionals, physicians, industries and the general population.

Objectives: Stress urinary incontinence (SUI) negatively affects the quality of life and sexual function in women. This study aimed to evaluate the efficacy of radiofrequency (RF) therapy in reducing SUI symptoms and its impact on sexual function. Methods: Thirty-four women with SUI were enrolled and underwent a single RF treatment session using the Viveve® System (Viveve Medical Inc., USA) with parameters of 90 J/cm² and 220 pulses per hour. Assessments at baseline and 6 months post-treatment included perineal ultrasound and personal interviews to evaluate lower urinary tract symptoms and sexual function. Urodynamic studies, voiding diaries, and questionnaires such as the Female Sexual Function Index (FSFI), Overactive Bladder Symp-tom Score (OABSS), Urogenital Distress Inventory-6 (UDI-6), Incontinence Impact Question-naire-7 (IIQ-7), and International Consultation on Incontinence Questionnaire-Short Form (ICIQ-SF) measured outcomes. Results: RF therapy significantly improved sexual function, with higher FSFI scores in all domains except pain at 6 months. SUI symptoms were significantly re-duced, as indicated by improved scores on OABSS, UDI-6, IIQ-7, and ICIQ-SF, alongside better voiding diary results. Anatomical changes included reduced bladder neck mobility, decreased vaginal width, and a reduced rotation angle of the proximal urethra. Conclusions: RF therapy is effective and safe for treating mild to moderate SUI and enhances sexual function, potentially due to changes in vaginal topography. These results suggest RF therapy as a viable non-surgical op-tion for managing SUI and improving sexual health.

Raru’s plants bark has long been used as traditional medicine in Batak’s tribe. Raru’s bark is derived from several trees that are usually used in a mixture in Batak traditional beverages. This bark is generally used as antidiabetic remedies. This study aims to combine the rarus’s bark extract and mocaf activated-carbon (MAC) in order to study antidiabetics in rats. The combination of raru’s bark extract and MAC were tested on male rats as of Sprague Dawley strain for testing antidiabetic bioactivity. The result showed that antidiabetic activity of raru’s extract and MAC exposed the antidiabetic level declines in rat’s blood. The various treatments of different concentration ratios of raru’s extract and MAC useful in the experiments showed that the levels of blood level reduction were slightly different (14-21%). The raru’s extract pure was observed more effective in decreasing the blood glucose level in rat’s blood, in comparison the positive control. The mixture of raru’s extract and MAC with 75:25 ratio is better than 50:50 ratio. The involvement of MAC in the alleged antidiabetic agent did little in improving the blood glucose level decrease in rat’s blood. Raru’s extract and MAC indicate its potential utilization as an antidiabetic agent.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Modern search engines encounter a significant challenge when it comes to handling duplicate and nearly identical web pages, particularly during the indexing process for vast amounts of web content. This issue can lead to slow search results and increased costs due to the accumulation of storage space necessary for storing indexes. To tackle this issue, different techniques have been proposed to find similar websites. However, it has long been a challenge in research to distinguish between web pages. In the current study, sentence-level features i.e., hashcode and thresholding are used to determine the nearly identical web pages. We employ an adaptive threshold that enables the application of our model in both large- and small-scale settings. The benchmark datasets consisting of Shakespeare’s collections, free text, job descriptions, and Reuters-21578 are used to test the proposed approach. With an accuracy of 0.99 and an F1-score of 0.97, the proposed technique outperforms existing methods.

Forests have multifunctional roles. They not only increase forest carbon sinks through afforestation and management, but also indirectly realize multiple benefits of "economy + ecology + society". Therefore, we construct a multiple output-benefit system of forest carbon sinks based on the development of forest carbon sinks in provinces of China. This system is also able to distinguish the importance of forest carbon sinks from other outputs. For the efficiency evaluation of multi-level output systems, this paper constructs a cross-evaluation model based on evidential reasoning method, the original efficiency information by conducting efficiency evaluation before information fusion. Further, the spillover effects and influencing factors of forest carbon sink efficiency are analyzed through a spatial regression model to explore the spatial characteristics of forest carbon sink efficiency in China. The results show that: (1) there is a large gap between the cross-efficiency levels of forest carbon sinks in various regions of China, with significant spatial correlation. For the perspective of direct output benefits, the cross-efficiency of the eastern region is higher, while the cross-efficiency of the northwestern region is lower; for the perspective of indirect output benefits, the cross-efficiency of the southeastern region is higher. (2) China's forest carbon sink has a significant positive spillover effect, and the indirect output cross-efficiency has a significant negative impact on the forest carbon sink in its own region. Further analyzing the impact of indirect output cross-efficiency, it is found that the cross-efficiency of the ecological dimension and the cross-efficiency of the social dimension have a significant negative impact on the forest carbon sink in its own region, and the economic dimension has a significant positive impact on the forest carbon sink in its own region. In conclusion, corresponding policy recommendations are proposed for the development of forest carbon sinks to promote the realization of the dual-carbon goal.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

While numerous studies have explored the correlation between the built environment and ride-hailing demand, few have assessed their nonlinear interplay. Utilizing ride-hailing order data and multi-source built environment data from Nanjing, China, this paper uses the machine learning method, eXtreme Gradient Boosting (XGBoost), combined with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDP) to investigate the impact of built environment factors on ride-hailing travel demand, including their non-linear and threshold effects. The findings reveal that dining facilities have the most significant impact, with a contribution rate of 30.75%, on predicting ride-hailing travel demand. Additionally, financial, corporate, and medical facilities also exert considerable influence. The built environment factors need to reach a certain threshold or within a certain range to maximize the impact of ride-hailing travel demand. population density, land use mix and distance to the subway station collectively influence ride-hailing demand. The results are helpful for TNCs to allocate network ride-hailing resources reasonably and effectively.

Introduction. The Fat Mass and Obesity-Associated (FTO) gene encodes a demethylase that modulates RNA N6-methyladenosine (m6A) playing a regulatory role in adipocyte differentiation and pathogenesis of human obesity. Methods. To understand the potential role of FTO in osteoporosis (OP) we investigated five single nucleotide variations (SNVs) in intron 1 (rs8057044, rs8050136, rs9939609, rs62033406, rs9930506) in a cohort of postmenopausal women (n = 188) from Central Europe. Genotyping was performed by allele discrimination assay while haplotypes were reconstructed in population by PHASE 2.1. Results. The rs9930506 was strongly associated with OP (P &lt; 0.0035), supported by Bonferroni correction (P &lt; 0.0175) and all SNVs were stronger associated with severe OP with fragility fractures. Among 17 haplotypes, two were frequent (h1 and h9) and distributed in three main haplotypes pairs (h1/h1, h1/h9, h9/h9). Pathogenic pair h1/h9 was associated with leaner phenotype, fractures and lower bone mineral density (BMD) and carried heterozygous GA of rs9930506, while protective pair h9/h9 was associated with obesity and carried AA alleles of rs9939609. Conclusions. Concordant associations with OP, fractures risk and lower BMD at all skeletal sites indicate FTO as a promising candidate for OP explaining complex relationship with obesity and offer new perspectives for the study of epigenetic regulation of bone metabolism.

Salinity stress emerges as an important menace to global food security, particularly affecting susceptible crops such as common bean plants (Phaseolus vulgaris L.). The disruption of ion balances caused by salt stress withing plants cells reduces water and nutrient absorption, and hampers growth and productivity. Sacchorhiza polyschides, a brown macroalga rich in essential elements, and macrominerals, has drawn attention as a natural biostimulant, being a potential remedy to bolster crop resilience against salt stress. This study delves into the effect of water extracts of Sacchorhiza polyschides (SPE) across varying concentrations (1%, 2%, and 5%) in common bean plants under salt stress (68.4 mM NaCl) conditions. Two different methods of application were used: by spraying the aerial part of the plant or by irrigation together with the watering solution. The effects of both systems of application were studied on the aerial parts of the plants. SPE exhibited significant enhancements in morphological parameters, chlorophyll content, carbon-nitrogen activities, and antioxidant enzymatic system activities, alongside increasing osmolyte accumulation, compared to salt-stressed plants without biostimulation. Moreover, SPE reduced reactive oxygen species (ROS) levels caused by salt stress, mitigating lipid peroxidation. The concentrations of 2% and 5% SPE applied by spraying showed the most significant results in most of the parameters analyzed. By shedding light on the underlying science behind this biostimulant effect, this research underscores the potential of SPE to enhance crop resilience and augment food production in salt-challenged environments.

This article presents a low-cost insurance system developed for small-hold farms in disaster-prone regions, primarily using free Earth Observation (EO) data and Free Open Source Software (FOSS) – collectively termed sustainable geoinformatics - with a proprietary mobile phone app that enables verification. The study examined 30 farms in Risaralda department, Colombia. A Digital Elevation Model (12.5m pixels) from the ALOS PALSAR satellite sensor was used with a Geographical Information System (GIS) to map the terrain, drainage and geohazards of each farming district. Google Earth Engine (GEE) was used to carry out Time Series Analysis of 15 EO and weather datasets for 1998 to 2020. This analysis enabled the levels of risk from hydrometeorological hazards to be determined for each farm of the study, providing key data for the setting of insurance premiums. A parametric insurance product was piloted using GPS-tagged, time-stamped mobile phone photos to verify crop health. Key features of this insurance system are its low operational cost and rapid damage verification, relative to conventional approaches to farm insurance. It is an affordable form of insurance for small-scale farmers, with the rapid verification and payment of claims. This relatively fast, low-cost and affordable approach to insurance for small-scale farming enhances sustainable development by enabling policy-holder farmers to recover more quickly from disasters.

Fagao is one of China's traditional gluten free staple foods made by rice or corn flour. Corn Fagao prepared by co-fermentation with sourdough and yeast exhibits better quality and less staling compared to traditional yeast-fermented Fagao. The physicochemical properties of corn Fagao batter during the sourdough-yeast co-fermentation were investigated. The results showed that compared with yeast fermentation, the gas production and viscosity of the batter increased by co-fermentation. The co-fermented batter shows higher hydrolysis of starch and less amylose content. The integrity of starch granules in co-fermented batter was damaged more seriously, the crystallinity and short-range ordered structure were less than yeast fermented batter, even though the crystal structure type of starch did not change obviously. The peak viscosity, minimum viscosity, final viscosity, decay value and recovery value of corn batter are reduced by co-fermentation, which can improve the thermal stability of the batter and slow down the aging. Co-fermentation also results in a more pronounced reduction in protein subunit contents than yeast fermentation. The changes in the physicochemical properties of corn Fagao batter help explain the quality improvement of corn Fagao made from co-fermentation method, and may provide theoretical references for co-fermentation with sourdough and yeast to other gluten free foods.

We study theoretically the Josephson diode effect (JDE) realized in a system composed of parallel-coupled double quantum dots (DQDs) sandwiched between two semiconductor nanowires deposited on an s-wave superconductor surface. Due to the combined effects of the proximity-caused superconductivity, strong Rashba spin-orbit interaction and Zeeman splitting inside the nanowires, a pair of Majorana bound states (MBSs) may possibly emerge at opposite ends of each nanowire. Different phase factors arisen from the superconductor substrate can be generated in the coupling amplitudes between the DQDs and MBSs prepared at the left and right nanowires, and will result in the Josephson current. We find that the critical Josephson currents in positive and negative directions are different from each other in amplitude within an oscillation period with respective to the magnetic flux penetrating through the system, a phenomenon known as the JDE. It arises from the quantum interference effect in this double-path device, and can hardly occur in system of one QD coupled to MBSs. Our results also show that the diode efficiency can reach up to 50%, and depends on the overlap amplitude between the MBSs and the energy levels of the DQDs adjustable by gate voltages. The present model is realizable within current nanofabitication technologies and may find practical use in interdisciplinary field of Majorana and Josephson physics.

This study investigated the effectiveness of virtual reality (VR) technology in table tennis education compared to traditional training methods. A 12-week randomized controlled trial was conducted with 120 participants divided equally between VR and traditional training groups. Performance metrics, learning motivation, and satisfaction were assessed at regular intervals. Results demonstrated significant advantages of VR training, with the VR group showing superior improvements in serve accuracy (23.5% vs. 15.8%, p < 0.001), rally endurance (increase of 8.2 vs. 5.7 shots, p < 0.01), and overall skill scores (18.7 vs. 13.2 points improvement, p < 0.001). The VR group also exhibited higher increases in learning motivation (23.5% vs. 12.8%, p < 0.001) and satisfaction (31.5% vs. 18.7%, p < 0.001). Subgroup analysis revealed particular benefits for novice players and younger participants. These findings suggest that VR technology offers a promising approach to enhance table tennis education, potentially revolutionizing sports training methodologies. Future research should focus on long-term skill retention and the optimization of VR training protocols.

Non-toroidal shape primary pass through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow passing several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables pass through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed causing the malfunction of the CT. In this paper, the performance of a non-toroidal shape protection CT is studied. The research is focused on the cable position influence in possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from assigned ratio. The validation of this phenomenon has been carried out via Finite Element Analysis (FEA) showing that partial transformer core saturations appears in areas of the magnetic core close to the cable. Applying FEA, also the admissible accuracy region for cable positioning inside the CT is delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs varying the primary cables’ positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

The use of omega-3 fatty acids (omega-3 FA) in the treatment of atopic dermatitis (AD) is an area of ongoing research. Some studies suggest that dietary supplementation with omega-3 FA can help manage symptoms of AD by reducing lesion severity, skin inflammation, dryness and itching, while other show no significant beneficial effect. The aim of this study was to evaluate the effect of omega-3 FA form fish oil in combination with GLA form blackcurrant seed oil in children with AD. This is a longitudinal, prospective, randomized, triple blind, placebo-controlled parallel clinical trial. The study was conducted during the 2-year period from autumn, winter, and spring avoiding the summer when AD usually improves. Children were randomized to receive the active study product (Mega Kid®) containing specific blend of omega-3 and omega-6 fatty acids or placebo. Primary outcomes were change in severity of AD measured using SCORing Atopic Dermatitis (SCORAD) patient oriented SCORAD (PO-SCORAD) and the difference in TCS use. Secondary outcomes were change in itch intensity, sleep quality and Family Dermatology Life Quality Index (FDLQI). Data were analyzed for 52 children (26 in the intervention group and 26 in the placebo group). In children receiving active product intention-to-treat analysis showed that after 4 months of treatment, there was a significant decrease in the SCORAD index (from median 42 to 25, p < 0.001) and use of topical corticosteroids (from median 30 to 10 mg/day, p < 0.001) but also significant improvement in itch, sleep quality and overall quality of life. Omega-3 fatty acids in combination with GLA and vitamin D has a great beneficial effect in treatment of atopic dermatitis in children. Therefore, we can conclude that supplementation with this specific combination could be considered a safe and effective intervention that can significantly reduce the severity of AD in pediatric patients.

The purpose of this study was to examine the problem of violent extremism among young people. Additionally, a youth violent extremism scale (YVES) was developed that takes into account the differences between and within Arab cultures. The goal was to produce a scale that could be used and tested within an Arab country or between Arab countries. The scale was developed in three stages: generation, refinement, and validation. A literature review and nomological network were utilized to show the scale's dimensions, correlations to those dimensions, and other relevant variables (such as the LSC, LSE, and criminality scale). A sample of 6726 young students from fifteen Arab countries and the authorities involved were selected. Findings showed that six factors were obtained through principal component factor analysis using Varimax and Kaiser normalization (29 items). A significant positive association was found (r=.651, p = 0.000), supporting the scale's validity. Using Cronbach's alpha, the scale reliability was strong and assessed at 0.98. The scale's construct validity was estimated by assessing the correlation between the Youth Violent Extremism scale and low self-control. A significant positive correlation (r=.651, p = 0.000) indicates the scale's validity. Findings showed significant differences between males and females in youth violent extremism (F = 13.678, α ≤0.000). Descriptive results showed, however, that females have a slightly higher mean of violent extremism than males (M =85.2 vs. 87.6), with a close variation (26 vs. 27) for males and females, respectively. In this study, a measurement tool was provided that can be used as a knowledge base for security strategies. The scale can be applied to identify legal, social, and educational policies and applications of violent extremism. Future research is needed to test the scale on different professions like teachers, police officers, and parents. Also, a need to test the scale on different age groups, settings, and cultures. A need for atheoretical and empirical framework for understanding and preventing youth violent extremism through promoting a more cohesive and resilient youth society.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

In the frame of our diversity-oriented research on multitarget small molecule anticancer agents, utilizing convergent synthetic sequences terminated by Sonogashira coupling reactions, a preliminary selection of representative alkyne-tethered vindoline hybrids was synthesized. The novel hybrids with additional pharmacophoric fragments of well-documented anticancer agents, including FDA-approved tyrosine-kinase inhibitors (imatinib and erlotinib) or ferrocene or chalcone units, were evaluated for their antiproliferative activity on malignant cell lines MDA-MB-231 (triple negative breast cancer), A2780 (ovarian cancer), HeLa (human cervical cancer) and SH-SY5Y (neuroblastoma) as well as human embryonal lung fibroblast MRC-5 served as reference non-malignant cell line for the assessment of the therapeutic window of the tested hybrids. The biological assays identified a trimethoxyphenyl-containing chalcone-vindoline hybrid (36) as a promising lead compound exhibiting submicromolar activity on A2780 cells with a marked therapeutic window. These results suggest that ovarian cancer might be considered as a prioritized target of treatment with 36.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

Renal cell carcinoma (RCC) accounts for approximately 90-95% of all kidney cancers in adults, with the clear cell RCC (ccRCC) the most frequently identified subtype. RCC is known for its responsiveness to immunotherapy, making it an area of significant research interest. Immune checkpoint (IC) molecules, which regulate immune surveillance, are established therapeutic targets in RCC. The aim of this study was to analyze the influence of polymorphisms in genes HVEM and CD160 on susceptibility to ccRCC and patient overall survival (OS) with over a ten-year period of observation. We genotyped three HVEM single nucleotide polymorphisms (SNPs): rs1886730, rs2234167, and rs8725, and two CD160 SNPs: rs744877 and rs2231375, in 238 ccRCC patients and 521 controls. Our findings indicated that heterozygosity within rs2231375 and/or rs2234167 increases ccRCC risk. Furthermore, in women, heterozygosity within additional HVEM SNPs, rs8725 and rs1886730, is associated with an increased ccRCC risk. The presence of a minor allele for rs1886730, rs2234167, rs8725, and rs2231375 was also correlated with certain clinical features of the disease. Moreover, the rs1886730 SNP was found to be associated with patients' OS. In conclusion, our study highlights an association between HVEM and CD160 polymorphisms and the risk of developing ccRCC as well as patient’s OS.

In this study, the team employed full-scale crash tests to investigate the impact of post-densification technology on the safety performance of separated central median W-beam barriers under low compaction conditions. By precisely simulating the design and construction environment of the central median, the study comprehensively evaluated the barrier's containment, redirection, buffering, and anti-intrusion performances, as well as the deformation of both the barrier and vehicles under various collision scenarios. The results indicate that under low compaction soil conditions, the A-level separated central median barriers reinforced with post-densification technology effectively meet the specified protection requirements. By comparing the influence of soil strength variations on barrier performance under simulated rainfall conditions, it was confirmed that enhancing soil compaction significantly improves soil stability, effectively increases the overall strength and stability of the barriers, reduces deformation, and significantly enhances safety performance. This study not only validates the effectiveness of the reinforcement scheme but also provides new perspectives for the scientific research of safety barriers and offers crucial technical support for the optimal design of road safety protection facilities.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Continuous-wave photocathode guns are capable of delivering electron beams with high repetition rates and high average currents. However, they are limited by relatively low accelerating gradients and cathode fields. This limitation leads to a larger beam size at the gun exit due to space charge forces, making the beam more sensitive to optical aberrations and posing challenges for low-emittance electron beam transmission. This paper focuses on the aberrations induced by multipole fields. We analyze the effects of quadrupole, sextupole, and higher-order fields on beam profile and transverse emittance and propose a beam-based method for the rapid characterization and correction of these multipole fields. Furthermore, we present an experimental study conducted on the DC-SRF-II photocathode gun equipped with dedicated correctors. Both simulation and experimental results demonstrate that our approach effectively mitigates beam aberrations caused by multipole fields, resulting in improved beam symmetry and reduced emittance.

A two-stage pilot plant study has been completed that evaluated the performance of a reverse osmosis (RO) membrane process for the treatment of a feedwater that consisted of a blend of nanofiltration (NF) concentrate and brackish groundwater. Membrane performance was assessed by monitoring the process operation, collecting water quality data, and documenting the blended feedwater’s impact on fouling due to a combination of, or solely caused by, plugging, scaling, microbiological, or organic means. Fluorescence and biological activity reaction tests were used to identify the types of organics and microorganisms present in the blended feedwater. Additionally, scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) were used to analyze suspended matter that collected on the surfaces of cartridge filters used in the pilot’s pretreatment system. SEM and EDS were also used to evaluate solids collected on the surfaces of 0.45-µm silver filter pads after filtering known volumes of NF concentrate and RO feedwater blends. Water quality analyses confirmed that the blended feedwater contained little to no dissolved oxygen, and the blended feedwater was absent of a significant amount of particulate matter as defined by silt density index and turbidity measurements. However, water quality results suggested that the presence of sulfate, sulfide, iron, anaerobic bacteria, and humic acid organics likely contributed to the formation of pyrite observed on some of the membrane surfaces autopsied at the conclusion of pilot operations. It was determined that first-stage membrane productivity was impacted by the location of cartridge filter pretreatment; however, second-stage productivity was maintained with no observed flux decline during the entire pilot operation’s timeline. Study results indicated that the operation of an RO process treating a blend of NF concentrate and brackish groundwater could maintain a sustainable and productive operation that provided a practical zero-discharge process operation while the dilution of RO feedwater salinity would lower overall production costs.

The microstructure of oil pipeline steels is polycrystalline due to the presence of a complex grain boundary (GB) network in them. The performance of them when exposed to stresses in corrosive environments is largely dictated by the interplay between the hydrogen (H) diffusion, the dislocation slip, and their interactions with the GBs. However, the slip-GB interaction in the presence of H and the subsequent cracking along the GBs remains not fully understood up to date. It is challenging to simultaneously resolve the collective dislocation motions away from the GBs together with the H diffusion near the atomically structured GBs using single-scale techniques. To address this challenge, taking bcc iron as a model material, here we present a a concurrent atomistic-continuum (CAC) computational analysis of the interaction between dislocation slip and a H-charged GB. With the large number of dislocations-mediated plastic flow away from the GB together with the atomistic structure evolution at the GB being simultaneously retained, several main findings from our simulations are: (i) the large number of dislocation-mediated pileup-induced internal stress nearby the H-charged GB can be as high as 3GPa; (ii) the more dislocations accumulated nearby the GB, the slower H diffusion ahead of the slip-GB intersection; (iii) H atoms diffuse fast behind the pileup tip, get trapped within the GB, and diffuse slow ahead of the pileup tip; (iv) the local stresses nearby the pileup tip exhibits a strong heterogeneity along the dislocation line direction. This differs from the common wisdom in many existing 2D theories/models. The buildup of such a high local stress heterogeneity leads to inhomogeneous H diffusion within the GB plane. The CAC simulation-predicted local H diffusivity, Dpileup−tip, and local stresses, σ, nearby the GB are then correlated with each other and consolidated into a mechanics model by considering the dislocation pileup as an Eshelby inclusion. These findings will provide researchers with opportunities to: (a) characterize the coupled dynamics between plasticity, H diffusion, and crack initiation underlying the hydrogen-induced cracking (HIC); (b) develop mechanism-based constitutive rules to be used in diffusion-plasticity coupling models for understanding the interplay between mechanical and mass transport in materials at the continuum level; and (c) connect the atomistic deformation physics of polycrystalline materials with their overall performance in aqueous environments, which is currently difficult to achieve in laboratory experiments.

This study aimed to conduct a cross-cultural adaptation of the development of the cat-owner/dog-owner relationship scales. The method encompassed several stages: conceptual, item, semantic, operational, measurement, and functional equivalence. Processes included translations, synthesis of translations, back-translations, consensus on the English versions, external evaluation by the original authors, expert committee evaluation, and pre-tests. The study involved surveying 342 pet owners throughout Brazil using a 20-item questionnaire. Data analyses utilized confirmatory factor analysis, covariance-based modeling, and multigroup analysis. The techniques confirmed that the scale preserved its psychometric properties and showed no variance between dog and cat owners, indicating that the measured constructs are universal and unaffected by specific cultural nuances. Hence, the cross-cultural adaptation and validation of the scale facilitate applying and testing concepts and measures in diverse contexts, enriching our understanding of the dynamics between owners and their pets (dogs and cats) in different living situations. In addition, this research holds particular significance in Brazil, given the country’s vast cultural diversity.

Considering animal welfare, the free-range laying hen farming model is increasingly gaining attention. However, in some countries, large-scale farming still relies on the cage-rearing model, making the focus on the welfare of caged laying hens equally important. To evaluate the health status of caged laying hens, a dataset comprising visible light and thermal infrared images was established for analyses, including morphological, thermographic, comb, and behavioural as-sessments, enabling a comprehensive evaluation of the hens' health, behaviour, and population counts. To address the issue of insufficient data samples in the health detection process for indi-vidual and group hens, a dataset named BClayinghens was constructed containing 61,133 images of visible light and thermal infrared images. The BClayinghens dataset was completed using three types of devices: smartphones, visible light cameras, and infrared thermal cameras. All thermal infrared images correspond to visible light images and have achieved positional alignment through coordinate correction. Additionally, the visible light images were annotated with chicken head labels, obtaining 63,693 chicken head labels, which can be directly used for training deep learning models for chicken head object detection and combined with corresponding thermal infrared data to analyze the temperature of the chicken heads. To enable the constructed deep-learning object detection and recognition models to adapt to different breeding environ-ments, various data enhancement methods such as rotation, shearing, colour enhancement, and noise addition were used for image processing. The BClayinghens dataset is important for ap-plying visible light images and corresponding thermal infrared images in the health detection, behavioural analysis, and counting of caged laying hens under large-scale farming.

In this nano era, nanomaterials and nanostructures are popular in developing novel functional materials. However, the combinations of nanoproducts with materials at micro and macro scale can open new routes for conceiving novel materials with an improved or even new functional performances. In this study, a brand-new hybrid, containing both nanofibers and particles having a microsize, was fabricated using a sequential electrohydrodynamic atomization (EHDA) process. Firstly, the microparticles loaded with drug (berberine hydrochloride, BH) molecules in the cellulose acetate (CA) were fabricated using a solution electrospraying process. Later, these microparticles were suspended into a co-dissolved solution containned BH and a hydrophilic polymer (polypyrrolidone, PVP), and were co-electrospun into the nanofiber/microparticle hybrids. The EHDA processes were clearly recorded, and the resultant products showed a typical hybrid topography, with microparticles distributed all over the nanofibers, which was demonstrated by SEM assessments. FTIR and XRD demonstrated that the components within the hybrids were presented in an amorphous state and have fine compatibility with each other. In vitro dissolution tests verified that the hybrids were able to provide the designed dula-step drug release profiles, a combination of the fast release step of BH from the hydrophilic PVP nanofibers through an erosion mechanism and the sustained release step of BH from the insoluble CA microparticles via a typical Fickian diffusion mechanism. The present protocols pave a new way for developing trans-scale functional materials.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

Fibroin-chitosan composites, especially those containing nanohydroxyapatite, show potential for bone tissue regeneration. The physicochemical properties of these biocomposites depend on the compatibility between their components. In this study, the intermolecular interactions of fibroin and chitosan were analyzed using a molecular dynamics approach. Two types of systems were investigated: one containing acetic acid and the other containing calcium (Ca²⁺) and hydrogen phosphate (HPO₄²⁻) ions mimicking hydroxyapatite conditions. After obtaining the optimal equilibrium structures, the distributions of several types of interactions including hydrogen bonds, ionic contacts, and hydrophobic contacts along with the structural and energetical features were examined. The calculated binding energy values for the fibroin-chitosan complexes confirm their remarkable stability. The high affinity of fibroin for chitosan can be explained by the formation of a dense network of interactions between considered biopolymers. These interactions were found to be primarily hydrogen bonds and ionic contacts involving ALA, ARG, ASN, ASP, GLN, GLU, GLY, LEU, PRO, SER, THR, TYR, and VAL residues. As it was established, the complexation of fibroin with chitosan maintains the β-sheet conformation of the peptide. β-Sheet fragments in fibroin are involved in the formation of significant amount of hydrogen bonds and ionic contacts with chitosan.

Under the new pattern of “double carbon” development, good ESG performance is the best way to promote the sustainable development of enterprises, and the ESG investment strategies are directly affected by the strategic vision of managers. Based on the upper echelons theory and stakeholder theory, this paper takes Chinese A-share listed companies from 2011 to 2022 as samples to empirically analyze the impact of managerial myopia on corporate ESG performance. The results show that managerial myopia significantly inhibits corporate ESG performance, mainly by inhibiting corporate green investment and green innovation sustainability. Furthermore, for state-owned enterprises (SOE), heavy polluting enterprises (HPE) and non-high-tech enterprises, the inhibitory effect of manager myopia on ESG performance is stronger. When the enterprise is in the growth stage, the above inhibition effect is more severe. For external governance, the greater the analyst attention and public environmental attention are, the more conducive they are to alleviating the restraining effect of managerial myopia on enterprise ESG performance. Therefore, effectively improving the time cognition level of managers and strengthening external supervision have become important measures for comprehensively optimizing the ESG performance.