Changes in sea level exhibit nonlinearity, nonstationarity, and multivariable characteristics, making traditional time series forecasting methods less effective in producing satisfactory results. To enhance the accuracy of the predictions of changes in sea level, this study introduced an improved VMD–EEMD–LSTM hybrid model. This model decomposes satellite altimetry data from near the Dutch coast using VMD, resulting in components of the Intrinsic Mode Function (IMF) with various frequencies and a residual sequence. EEMD further dissects the residual sequence obtained from VMD into second-order components. These IMFs decomposed by VMD and EEMD are utilized as features in the LSTM model for making predictions, culminating in the final forecasted results. The experimental results demonstrated significant improvements in the predictive performance compared with the VMD–LSTM model. The RMSE (root mean square error) decreased by an average of 58.68%, the MAE (mean absolute error) reduced by an average of 59.96%, and the R2 (coefficient of determination) increased by an average of 49.85% compared with the VMD–LSTM model. In comparison with the EEMD–LSTM model, the RMSE decreased by an average of 26.95%, the MAE decreased by an average of 28.00%, and the R2 increased by an average of 6.53%. The VMD–EEMD–LSTM model exhibited significantly improved predictive performance.

An improved FSM method is used in geophysical and environmental corrections to enhance the final product of the along track Jason-2 SLA data and extend it near the Red Sea borders. In this study the ionospheric correction range, wet tropospheric correction range, sea state bias correction range and dry tropospheric correction range are enhanced and improved using FSM01, which helped to retrieve three more tracks (106, 170 and 234), earlier neglected by the distribution centers, and extend the tracks towards the coast. The FSM01 SLA is compared with Jason-2 SLA and AVISO SLA for the available 5 tracks, in which the FSM01 SLA show a good agreement and higher correlation with the Jason-2 SLA compared with that of AVISO, in addition to that it fills the gaps in the times series of all tracks. The new retrieved tracks also compared with those retrieved by AVISO, both data show similar variability, with FSM01 SLA show no gaps in the time series. The FSM01 SLA also extended towards the coast and show high correlation with the coastal tide measurements.

Traditional ways of validating satellite-derived sea surface temperature (SST) and sea surface salinity (SSS) products, using comparisons with buoy measurements, do not allow for evaluating the impact of mesoscale to submesoscale variability. Here we present the validation of remotely-sensed SST and SSS data against the unmanned surface vehicle (USV) – Saildrone – measurements from the Spring 2018 Baja deployment. More specifically, biases and root mean square differences (RMSD) were calculated between USV-derived SST and SSS values, and six satellite-derived SST (MUR, OSTIA, CMC, K10, REMSS, and DMI) and three SSS (JPLSMAP, RSS40, RSS70) products. Biases between the USV SST and OSTIA/CMC/DMI were approximately zero while MUR showed a bias of 0.2C. OSTIA showed the smallest RMSD of 0.36C while DMI had the largest RMSD of 0.5C. An RMSD of 0.4C between Saildrone SST and the satellite-derived products could be explained by the daily variability in USV SST which currently cannot be resolved by remote sensing measurements. For SSS, values from the JPLSMAP product showed saltier biases of 0.2 PSU, while RSS40 and RSS70 showed fresh biases of 0.3 PSU. An RMSD of 0.4 PSU could not be explained solely by the daily variability of the USV-derived SSS. Coherences were significant at the longer wavelengths, with a local maximum at 100 km that is most likely associated with the mesoscale turbulence in the California Current System.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

The hyper-arid environment is characterized by high inter-annual climatic fluctuations. The yearly average rainfall can change substantially for several years, forming wet or dry sub-periods. Observing rainfall trends over a sub-period can lead to a false perception of a change in the trend but may in fact represent a periodic cycle when examined on a larger time scale. We aimed to better characterize the rainfall regime prevailing in the hyper-arid Arava Valley (Israel/Jordan), and to examine the response of vegetation to annual rainfall. We hypothesized that annual and perennial vegetation would respond differently to wet and dry sub-periods, and that grazing activities will impact vegetation growth. We used a time series of monthly rainfall, from which we calculated Standard Precipitation Index (SPI), and calculated proxies of perennial and annual vegetation over the last four decades using Landsat-derived Normalized Difference Vegetation Index (NDVI). We found no clear trend in rainfall amounts during this period, however we did identify wet and dry sub-periods which were statistically distinct in rain and in vegetation patterns from each other. The highest levels of correlation between rainfall and the NDVI derived proxies were found when examining average rainfall over a period of two- three years for the annual vegetation and over four years for perennial vegetation. Using the Mann-Kendall test, we identified a time lag of two to four years, with the proxies of annual vegetation responding faster than the proxies of perennial vegetation, to shifts between wet and dry sub-period. In addition, we found a consistent difference between natural vegetation cover in Jordan (grazed) and Israel (non-grazed), favoring the development of natural vegetation on the Israeli side. We conclude that integrating between long-term remote sensing satellite imagery and climatic records revealed the greater resilience of perennial vegetation in the hyper-arid region to climatic fluctuation, and enabled us to identify the vegetation’s sensitivity to anthropogenic impact.

Observed sea surface Ka-band normalized radar backscatter cross section (NRCS) and Doppler velocity (DV) exhibit energy at low frequencies (LF) below the surface wave range. It is shown that non-linearity in NRCS-wave slope Modulation Transfer Function (MTF) and inherent NRCS averaging within the footprint account for the NRCS and DV LF variance with the exception of VV NRCS for which almost half of the LF variance is attributable to wind fluctuations. Although the distribution of radar DV is quasi-Gaussian suggesting virtually little impact of non-linearity, the LF DV variations arise due to footprint averaging of correlated local DV and non-linear NRCS. Numerical simulations demonstrate that MTF non-linearity weakly affects traditional linear MTF estimate (less than 10% for |MTF|< 20). Thus the linear MTF is a good approximation to evaluate the DV averaged over large footprints typical of satellite observations.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

In the paper the verification of forecasts of precipitation conditions measured by the standardized precipitation index SPI is presented. For the verification of categorical forecasts a contingency table was used. Standard verification measures were used for the SPI value forecast. The 30 day SPI moved every 10 days by 10 days was calculated in 2013-2015 from April to September on the basis of precipitation data from 35 meteorological stations in Poland. Predictions of the 30 day SPI were created in which precipitation was forecasted in the next 10 days (the SPI 10-day forecast) and 20 days (the SPI 20-day forecast). Both for the 10 and 20 days, the forecasts were skewed towards drier categories at the expense of wet categories. There was a good agreement between observed and 10-day forecast categories of precipitation. Less agreement is obtained for 20-day forecasts – these forecasts evidently “over-dry” the assessment of precipitation anomalies. The 10-day SPI value forecast accuracy is acceptable, whereas for the 20-day forecast is unsatisfactory. Both for the SPI categorical and the SPI value forecast, the 10-day SPI forecast is reliable and the 20-day forecast should be accepted with reservation and used with caution.

At an energy flux imbalance of about 1 W m–2, the ocean is storing 90 % of the heat accumulating by global warming. However, neither the causes nor the responsible geophysical processes are sufficiently well understood. More detailed investigations of the different phenomena contributing to the oceanic energy balance are warranted. Here, the role of low-level marine clouds in the air-sea interaction is analysed. TEOS-10, the International Thermodynamic Equation of State of Seawater – 2010, is exploited for a rigorous thermodynamic description of the climatic trend of the Lifted Condensation Level (LCL) of the marine troposphere. Rising Sea-Surface Temperature (SST) at constant Relative Humidity (RH) is elevating marine clouds, cooling the cloud base and reducing the downward thermal radiation. This LCL feedback effect is negative and counteracting ocean warming. At the current global SST of about 292 K, the net radiative heat flux from the ocean surface to the LCL cloud base is estimated to 24 W m–2. Per degree of SST increase, this net flux is expected to be enhanced by almost 0.5 W m–2. The climatic LCL feedback effect is relevant for the ocean’s energy balance and may thermodynamically rigorously be modelled in terms of TEOS-10 equations. LCL height may serve as a remotely measured, sensitive estimate for sea surface relative fugacity, or conventional relative humidity.

X-band marine radar captures signal reflected from the sea surface. Theoretical studies indicate that the initial unfiltered signal contains meaningful information including parameters related to wind waves. Traditional methods for estimating significant wave height (SWH) rely on the physical laws describing signal reflection from rough surfaces. However, recent studies suggest the feasibility of employing artificial neural networks (ANNs) for SWH approximation. Both classical and ANN-based approaches necessitate costly in situ data. In this study, we propose generating synthetic radar images with specified wind wave parameters using Fourier-based approach and Pierson–Moskowitz wave spectrum as a viable alternative. We generate synthetic images and use them for unsupervised learning approach to train a convolutional component of an ANN. After that, we train a regression ANN based on the previous convolutional component to obtain SWH back from synthetic images. Then, we apply preliminary trained weights for the same regression model to train SWH approximation on the dataset of real sea clutter images. In this study, we demonstrate the increase in the accuracy of SWH estimation from radar images with the preliminary training on synthetic data.

Sea surface salinity (SSS) is one of the Essential Climate Variables (ECVs) as defined by the Global Climate Observing System (GCOS). Acquiring high-quality SSS datasets with high spatial-temporal resolution is cruicial for research on the hydrological cycle and earth climate. This study assessed the quality of SSS data provided by four high-resolution ocean reanalysis products, including the Hybrid Coordinate Ocean Model (HYCOM) 1/12° global reanalysis, the The Copernicus Global 1/12° Oceanic and Sea Ice GLORYS12 Reanal-ysis, the Simple Ocean Data Assimilation (SODA) reanalysis, the ECMWF Oceanic Reanalysis System 5 (ORAS5) product and the Estimating the Circulation and Climate of the Ocean Phase II (ECCO2) reanalysis. Regional comparison in the Mediterranean Sea shows that reanalysis largely depicts the accurate spatial SSS structure away from river mouths and coastal areas but slightly underestimates the mean SSS values. Better SSS reanalysis performance is found in the Levantine Sea while larger SSS uncertainties are found in the Adriatic Sea and the Aegean Sea. The global comparison with CMEMS level-4 (L4) SSS show generally con-sistent large-scale structures. The mean ΔSSS between monthly gridded reanalysis data and in situ analyzed data is -0.1 PSU in the open seas between 40°S and 40°N with the mean Root Mean Square Deviation (RMSD) generally smaller than 0.3 PSU and the majority of correlation coefficients higher than 0.5. Comparison with collocated buoy salinity shows that reanalysis products well captures the SSS variations at the locations of tropical moored buoy arrays at weekly scale. Among all the four products, the data quality of HYCOM re-analysis SSS is highest in marginal sea, GLORYS12 has the best performance in the global ocean especially in tropical regions. Comparatively, ECCO2 has the overall worst performance to reproduce SSS states and variations by showing the largest discrepancies with CMEMS L4 SSS.

Sea surface partial pressure of CO2 (pCO2) is a critical parameter in the quantification of air-sea CO2 flux, which plays an important role in calculating the global carbon budget and ocean acidification. In this study, we use chlorophyll-a concentration (Chla), sea surface temperature (SST), absorption due to dissolved and particulate detrital matter (Adg), diffuse attenuation coefficient of downwelling irradiance at 490nm (Kd) and mixed layer depth (MLD) as input data for retrieving the sea surface pCO2 in the North Atlantic based on a remote sensing empirical approach with the Categorical Boosting (CatBoost) algorithm. The results show that the root mean square error (RMSE) is 8.25μatm, the mean bias error (MAE) is 4.92μatm and the coefficient of determination (R2) can reach 0.946 in the validation set, which mean that the CatBoost model makes an improvement compared to other models in the published studies. In the further analysis of the spatial and temporal distribution of the sea surface pCO2 in the North Atlantic, it can be found that the North Atlantic sea surface pCO2 has a clear trend with latitude variations and have strong seasonal changes. Furthermore, the sea surface pCO2 in this area is mainly affected by sea temperature and salinity, and influenced by biological activities in some sub-regions.

The results of numerical experiments with the chemistry-climate model of the Institute of Numerical Mathematics of the Russian Academy of Sciences - Russian State Hydro-Meteorological University (INM-RSHU CCM) in comparison with the MERRA2 reanalysis data are presented. To assess the impact of sea surface temperature (SST) on stratospheric processes and the ozone layer, numerical experiments were carried out for scenarios corresponding to the El Niño and La Niña Southern Oscillation phases. It is shown that the El Niño phase contributes to the enhancement of heat and mass transfer to the polar stratosphere, which strengthen the Brewer-Dobson circulation and the flux of wave activity that affect the zonal wind. As a result, during El Niño, the probability of sudden stratospheric warming increases and the stratospheric polar vortex (SPV) weakens, re-sulting in an increase in total polar stratospheric ozone. The La Niña phase, on the contrary, is accompanied by a weakening of heat and mass transfer from the troposphere to the stratosphere, as a result of which the stratospheric polar vortex strengthens and the total column ozone decreases. It is shown that the effect associated with the Southern Oscillation is more pronounced in the Northern Hemisphere than in the Southern Hemisphere. Numerical experiments were also carried out for scenarios in which the sea surface temperature was set corresponding to the early 1980s, and the results were compared with calculations in which the SST was set corresponding to the late 2010s. This allowed us to assess the influence of the multiyear trend in the SST increase on stra-tospheric processes and the ozone layer. It was shown that the SST increase is most pronounced in the Arctic, which corresponds to the phenomenon of "Arctic amplification", and therefore, the heat and mass transfer to the stratosphere increases in the Northern Hemisphere, which contributes to some weakening of the SPV and increase of the total column ozone. But, compared to the Southern Oscillation, the influence of the SST trend on the SPV and total column ozone is much weaker and is observed mainly in the Northern Hemisphere.

Global climate change has induced a rise in sea surface temperature (SST), although this increase is not uniform across the world. Significant variations exist between coastal and offshore waters, particularly in regions affected by upwelling processes. This study focuses on the Canary Current Upwelling System (CCUS), stretching from Northwest Iberia to Northwest Africa. High-resolution remotely sensed SST data (0.05°) from the ODYSSEA Level 4 Sea Surface Temperature Reprocessed dataset were validated with in-situ measurements and employed to establish a regional climatological baseline for 1982 – 2012. Subsequent years were compared to this baseline to construct SST anomaly maps, revealing SST changes since 2012. The study area was further divided into sub-regions for comparative analysis. Results indicate that SST consistently increased at a higher rate offshore compared to the adjacent nearshore regions. A reference dataset spanning 1951 – 1981 was used to gauge SST variability between the two baselines. SST exhibited a 0.59°C increase from 1951 – 1981 to 1982 – 2012, with a slowing of SST trends beyond the 1982 – 2012 baseline. This research offers valuable insights into the climatological dynamics of the CCUS. These findings enhance our understanding of this critical coastal system's climatology, laying the groundwork for future investigations into evolving climate patterns in coastal regions.

This paper introduces a new destriping algorithm for remote sensing data. The method is based on combined Haar Stationary Wavelet transform and Fourier filtering. State-of-the-Art methods based on the discrete wavelet transform (DWT) may not always be effective and may cause different artifacts. Our contribution is three-fold: i) we propose to use the Undecimated Wavelet transform (UWT) to avoid as much as possible shortcomings of the classical DWT; ii) we combine a spectral filtering and UWT using the simplest possible wavelet, the Haar basis, for a computational efficiency; iii) we handle 2D fields with missing data, as commonly observed in ocean remote sensing data due to atmospheric conditions (e.g., cloud contamination). The performances of the proposed filter are tested and validated on the suppression of horizontal strip artifacts in cloudy L2 Sea Surface Temperature (SST) and ocean color snapshots.

It has been shown that the Micro-Rain Radar (MRR) can be used to derive rainfall rates every 10 m over a depth of 1.28 km using the mean vertical air velocity corrected Doppler raindrop fall speed spectra. Furthermore, it has been shown that by assuming a reasonable advection velocity for the rain, these data can be analyzed to produce spatial radial power spectra often readily fit using a power function. Previous work has shown, however, that each spectrum applies only to each particular set of data and usually lacks the statistical qualifications necessary to be considered generally applicable. However, this limitation does not preclude the potential existence of other generalizations that can be used to explore the rainfall formation processes. The intent of this study, then, is to perform an initial look for such possible behaviors using time-height profiles of the rainfall rate. It is found that once the rainfall rate, R, exceeds about 20 mm h-1, there is, apparently, an associated flattening of the spectra with increasing R so that the smaller scales play an ever increasingly important role in such rain near the ground perhaps reflecting the increasing importance of such scales in the formation of pockets of more intense convective rain. The true generality of this finding needs additional scrutiny using more data particularly from two spatially separated MRR as is currently under preparation.

In this paper, a swarm trajectory planning method is proposed for multiple autonomous surface vehicles (ASVs) in an unknown and obstacle-rich environment. Specifically, based on the point cloud information of the surrounding environment obtained from local sensors, a kinodynamic path searching method is used to generate a series of waypoints in the discretized control space at first. Next, after fitting B-spline curves to the obtained waypoints, a nonlinear optimization problem is formulated to optimize the B-spline curves based on gradient-based local planning. Finally, a numerical optimization method is used to solve the optimization problems in real-time to obtain collision-free, smooth and dynamically feasible trajectories relying on a shared network. Simulation results demonstrate the effectiveness and efficiency of the proposed swarm trajectory planning method for a network of ASVs.

The video images captured at long range usually have low contrast floating objects of interest on a sea surface. A comparative experimental study of the statistical characteristics of reflections from floating objects and from the agitated sea surface showed the difference in the correlation and spectral characteristics of these reflections. The functioning of the recently proposed modified matched subspace detector (MMSD) is based on the separation of the observed data spectrum on two subspaces: relatively low and relatively high frequencies. In the literature the MMSD performance has been evaluated in generally and moreover using only a sea model (additive Gaussian background clutter). This paper extends the performance evaluating methodology for low contrast object detection and moreover using only the real sea dataset. This methodology assumes an object of low contrast if the mean and variance of the object and the surrounding background are the same. The paper assumes that the energy spectrum of the object and the sea are different. The paper investigates a scenario in which an artificially created model of a floating object with specified statistical parameters is placed on the surface of a real sea image. The paper compares the efficiency of the classical Matched Subspace Detector (MSD) and MMSD for detecting low-contrast objects on the sea surface. The article analyzes the dependence of the detection probability at a fixed false alarm probability on the difference between the statistical means and variances of a floating object and the surrounding sea.

In this paper, sea surface wind speed (SSWS) retrieval from Gaofen-3 (GF-3) quad-polarization stripmap (QPS) data in vertical-vertical (VV), horizontal-horizontal (HH) and vertical-horizontal (VH) polarizations is investigated in detail based on 3,170 scenes acquired from October 2016 to May 2018. The radiometric calibration factor of the VV polarization data is examined first. This calibration factor generally meets the requirement of SSWS retrieval accuracy with an absolute bias of less than 0.5 m/s but shows highly dispersed characteristics. These results lead to SSWS retrievals with a small bias of 0.18 m/s but a rather high root mean square error (RMSE) of 2.36 m/s compared with the ERA-Interim reanalysis model data. Two refitted polarization ratio (PR) models for the QPS HH polarization data are presented. Based on a combination of the incidence angle- and azimuth angle-dependent PR model and CMOD5.N, the SSWS derived from the QPS HH data shows a bias of 0.07 m/s and an RMSE of 2.26 m/s relative to the ERA-Interim reanalysis model wind speed. A linear function relating SSWS and the normalized radar cross section (NRCS) of QPS VH data is derived. The SSWS data retrieved from the QPS VH data show good agreement with the WindSat SSWS data, with a bias of 0.1 m/s and an RMSE of 2.02 m/s. We also apply the linear function to the GF-3 Wide ScanSAR data acquired for the typhoon SOULIK, which surprisingly yields a very good agreement with the model results. A comparison of SSWS retrievals among three different polarization datasets is also presented. The current study and our previous work demonstrate that the general accuracy of the SSWS retrieval based on GF-3 QPS data has an absolute bias of less than 0.3 m/s and an RMSE of 2.0 ±0.2 m/s relative to various datasets. Further improvement will depend on dedicated radiometric calibration efforts.

Sea ice surface roughness affects ice-atmosphere interactions, serves as an indicator of ice age, shows patterns of ice convergence and divergence, affects the spatial extent of summer melt ponds, and ice albedo. We have developed a method for mapping sea ice surface roughness using angular reflectance data from the Multi-angle Imaging SpectroRadiometer (MISR) and lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). Using an empirical data modeling approach, we derived estimates of Arctic sea ice roughness ranging from centimeters to decimeters meters within the MISR 275-m pixel size. Using independent ATM data for validation, we find that histograms of lidar and multi-angular roughness values are nearly identical for areas with roughness <20 cm but that for rougher regions, the MISR-derived roughness has a narrower range of values than the ATM data. The algorithm is able to accurately identify areas that transition between smooth and rough ice. Because of its coarser spatial scale, MISR-derived roughness data have a variance of about half that ATM roughness data.

A radial basis function network (RBFN) method is proposed to reconstruct daily Sea surface temperatures (SSTs) with limited SST samples. For the purpose of evaluating the SSTs using this method, non-biased SST samples in the Pacific Ocean (10°N–30°N, 115°E–135°E) are selected when the tropical storm Hagibis arrived in June 2014, and these SST samples are obtained from the OISST products according to the distribution of AVHRR L2p SST and in-situ SST data. Furthermore, an improved nearest neighbor cluster (INNC) algorithm is designed to search the optimal hidden knots for RBFNs from both the SST samples and the background fields. Then the reconstructed SSTs from the RBFN method are compared with the results from the optimum interpolation (OI) method. The statistical results show that the RBFN method has a better performance of reconstructing SST than the OI method in the study, and the average RMSE is 0.48°C for the RBFN method, which is quite smaller than the value of 0.69°C for the OI method. Additionally, the RBFN methods with different basis functions and clustering algorithms are tested, and we discover that the INNC algorithm with multi-quadric function is quite suitable for the RBFN method to reconstruct SSTs when the SST samples are sparsely distributed.

This bibliographic study addresses key aspects related to fishing, product safety, and climate change in the Adriatic Sea region. The examination of product safety focuses on the assessment of contaminants originating from human activities such as industry, mining, agriculture, and household waste disposal. The contamination of the aquatic environment has emerged as a pressing global concern, extending to the Adriatic subbasin. Aquatic organisms, including fish, are prone to accumulating pollutants directly from polluted water sources and indirectly through the food web. The bio-accumulation of potentially hazardous substances, particularly heavy metals, pesticides, PCBs, PAHs, and antibiotic resistance in aquatic organisms, poses a significant threat to human health. Climate change effects will deplete our seafood supply in terms of quantity and safety owing to negative consequences such as higher levels of pollution, parasites, viruses, infections, acidification, and toxicities such as shellfish poisoning. Global food safety strategies should be developed to reduce greenhouse gas emissions and promote environmentally friendly technology, which indirectly affects seafood quality and microbiological safety, especially for Adriatic Sea, which is part of the Mediterranean Sea, characterized by the most polluted waters in the world.

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

Validation of satellite sea surface salinity (SSS) products is typically based on comparisons with in-situ measurements at a few meters depth, that are mostly done at a single location and time. The difference in term of spatio-temporal resolution between the in-situ near-surface salinity and the two-dimensional satellite SSS results in a sampling mismatch uncertainty. The Climate Change Initiative (CCI) project has merged SSS from three satellite missions. Using an optimal interpolation, weekly and monthly SSS and their uncertainties are estimated at a 50 km spatial resolution over the global ocean. Over the 2016-2018 period the mean uncertainty on weekly CCI SSS is 0.13, whereas the standard deviation of weekly CCI minus in-situ Argo salinities is 0.24. Using high resolution SSS simulations, we estimate the expected uncertainty due to the CCI versus Argo sampling mismatch. Most of the largest spatial variability of the satellite minus Argo salinity are observed in regions with large mismatch. A quantitative validation is performed by considering the statistical distribution of the CCI minus Argo salinity normalized by the sampling and retrieval uncertainties. This quantity should follow a Gaussian distribution with a standard deviation of 1, if all uncertainty contributions are properly considered. We find that 1) the sampling mismatch can explain most of the observed differences between Argo and CCI data, especially for monthly products and in dynamical regions (river plumes, fronts), 2) overall, the uncertainties are well estimated in CCI version 3, much better compared to CCI version 2. There are a few dynamical regions where discrepancies remain, and where the satellite SSS, their associated uncertainties and the sampling mismatch estimates should be further validated.

The time’s arrow of macroscopic physical phenomenon is reflected by irreversible physical process, which essentially occurs from small probability state to high probability state. In this paper, simplified models are proposed to understand the macroscopic physical process. In order to describe the information of a physical system, we defined the full self-information as "information height" to describe the complexity or difficulty of a macrostate of physical system. In this way, the direction of macroscopic physical process is from high information height to low information height. We can judge the direction of physical process by the information height. If we want the macroscopic physical process to evolve from the low information height state to the high information height state, the system need to add extra information and corresponding energy to increase the information height.

The infrared (IR) satellite remote sensing of sea surface skin temperature (SSTskin) is challenging in the northern high latitude region, especially in the Arctic because of its extreme environmental conditions, and thus the accuracy of SSTskin retrievals is questionable. Several Saildrone uncrewed surface vehicles were deployed at the Pacific side of the Arctic in 2019, and two of them, SD-1036 and SD-1037, were equipped with a pair of IR pyrometers on the deck whose measurements have been shown to be useful in the derivation of SSTskin with sufficient accuracy for scientific applications, providing an opportunity to validate satellite SSTskin retrievals. This study aims to assess the accuracy of MODIS-retrieved SSTskin from both Aqua and Terra satellites by comparisons with collocated Saildrone-derived SSTskin data. The mean differences in SSTskin from the SD-1036 and SD-1037 measurements are different by ~0.4 K, largely resulting from differences in the atmospheric conditions experienced by the two Saildrones. The performance of MODIS on Aqua and Terra in retrieving SSTskin is comparable. Negative brightness temperature (BT) differences between 11 μm and 12 μm channels are identified as being physically based, but are removed from the analyses as they present anomalous conditions for which the atmospheric correction algorithm is not suited. Overall, the MODIS SSTskin retrievals show negative mean biases, -0.234 K for Aqua and -0.295 K for Terra. The variations in the retrieval inaccuracies show an association with diurnal warming events in the upper ocean from long periods of sunlight in the Arctic. Also contributing to inaccuracies in the retrieval is the surface emissivity effect in BT differences characterized by the Emissivity-introduced BT difference (EΔBT) index. This study demonstrates the characteristics of MODIS-retrieved SSTskin in the Arctic, at least at the Pacific side, and underscores that more in situ SSTskin data at high latitudes are needed for further error identification and algorithm development of IR SSTskin.

Ocean temperatures are increasing. Little work has been done to examine the effects that these changes will have on fishery production. The study at hand seeks to incorporate the influence of climate change into established bioeconomic fishery models. Stock biomass is approximated to be a function of sea surface temperature. Following a feasible generalized least squares regression using data from the Western and Central Pacific, the interaction between fishery effort and temperature is found to be statistically significant. From this model, various functional forms relating effort, catch, and temperature are specified. In particular, a function that returns an effort requirement given a target catch level and temperature forecast is generated.The importance of these tools for fishery management is explored through application to Western and Central Pacific tuna fisheries. Recommendations for extensions into future research are made and the foundation for a model of efficient effort allocation across time and the entirety of a management area, given changing temperatures, is specified.

Several disruptive attacks against companies in the maritime industry have led experts to consider the increased risk imposed by cyber threats as a major obstacle to undergoing digitization. The industry is heading toward increased automation and connectivity, leading to reduced human involvement in the different navigational functions and increased reliance on sensor data and software for more autonomous modes of operations. To meet the objectives of increased automation under the threat of cyber attacks, the different software modules that are expected to be involved in different navigational functions need to be prepared to detect such attacks utilizing suitable detection techniques. Therefore, we propose a systematic approach for analyzing the navigational NMEA messages carrying the data of the different sensors, their possible anomalies, malicious causes of such anomalies as well as the appropriate detection algorithms. The proposed approach is evaluated through two use cases, traditional Integrated Navigation System (INS) and Autonomous Passenger Ship (APS). The results reflect the utility of specification and frequency-based detection in detecting the identified anomalies with high confidence. Also, the analysis is found to facilitate the communication of threats through indicating the possible impact of the identified anomalies against the navigational operations. Moreover, we have developed a testing environment that facilitates conducting the analysis. The environment includes a developed tool, NMEA−Manipulator that enables the invocation of the identified anomalies through a group of cyber attacks on sensor data. Our work paves the way for future work in the analysis of NMEA anomalies toward the development of an NMEA intrusion detection system.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

Bistatic scattering coefficient have important application of ocean active microwave remote sensing. In this paper, a general expression of the composite scattering coefficient for multiple dielectric targets of one-dimensional fractal sea surface is derived by MOM method. Secondly, the bistatic scattering coefficient is computed, there are two class missile targets and one class ship target of one-dimensional fractal sea surface, and the influence of the water dielectric constant, fractal dimension, wind speed, the target dielectric constant and spatial position is discussed, and the corresponding conclusions are given. The proposed algorithm is able to solve some composite scattering problems, such as “dielectric or conductive object + rough surface”, “dielectric or conductive floating object +rough ”and it has certain generalization and reference.

The technology for determining the point’s coordinates on the earth’s surface using the global navigation satellite system (GNSS) is becoming the norm along with ground-based methods. In this case, determining coordinates does not cause any particular difficulties. However, to identify normal heights using this technology with a given accuracy, special research is required. The fact is that satellite determinations of geodetic heights (h) over an ellipsoid surface differ from ground-based measurements of normal height (HN) over a quasi-geoid surface by a certain value called quasi-geoid height or height anomaly (ζ). In relation to determining heights of a certain territory, the concept of geoid height (N) is usually operated when dealing with a geoid model. In this work, geodetic and normal heights are determined for 5 control points in three different regions in Lebanon, where measurements are carried out using GNSS technology and geometric levelling. The obtained quasi-geoid heights are compared with geoid heights derived from the global Earth model EGM2008. The results obtained showed that, in the absence of gravimetric data, the combination of global Earth model data, geometric levelling for selected areas and satellite determinations allows the creation of a high accurate altitude network for mountainous areas.

We have repeated the experiment performed recently by Krasznahorkay et al., (Phys. Rev. Lett. 116, 042501 (2016)), which may indicate a new particle called X17 in the literature. In order to get a reliable, and independent result, we used a different type of electron-positron pair spectrometer which have a more simple acceptance/efficiency as a function of the correlation angle, but the other conditions of the experiment were very similar to the published ones. We could confirm the presence of the anomaly measured at the Ex=18.15 MeV resonance, and also confirm their absence at the Ex=17.6 MeV resonance, and at Ep= 800 keV off resonance energies.

The study used ERA5 reanalysis SST dataset re-gridded to a common grid of 0.25° X 0.25° spatial resolution (latitude × longitude) for the historic (1940–2014) and projected (2015–2100). The SST simulation under the SSP5-8.5 scenarios was carried out with output from 8 General Circulation Models (GCMs). The bias-corrected dataset was developed using Empirical Quantile Mapping EQM for the historical (1940-2015) and the future (2030-2100) while the CMIP6 model simulation was evaluated against the ERA5 monthly rainfall observed data for monthly and annual sea surface temperatures (SST) over the Gulf of Guinea. ). The CMIP6 models simulation for SST projection from 2030-20100 based on SSPS 8.5 SST is projected to increase by 4.61o (31oC) in 2030 to 35oC in 20100 in the coastal GOG and 2.6oC in the Western GOG (Sahel). The correlation coefficient (r) was used to evaluate the performance of the CMIP6 models and the analysis showed ACCESS 0.1,CAMS CSM 0.2, CAN ESM 0.3, CMCC, 0.3 and MCM, 0.4 indicating that all models performed well in capturing the climatological pattern of the SST. The.CMIP6 bias corrected model simulations showed increased SST warming over the GOG will be higher in the Far period end than the Near-term climate. The study affirmed that the CMIP6 projections can be used for multiple assessments related to climate and hydrological impact studies and for the development of mitigation measures under a warming climate

We have carried out a systematic review of the scientific literature published on PM and, more specifically, on its presence in fish and seafood of interest to the population from Mediterranean area. Given its preference and wide acceptability in the scientific community, we followed the PRISMA. The potential functional and clinical toxicity in humans due to MP in fish must be considered by the chemical composition of the microplastics the presence of PM and its additives, associated contaminants and pathogens in fish and shellfish, as well as the possible effects on human health, requires improving legislation on evaluation and providing a basis for consumer protection.

Recent studies have elucidated the diversity of genes encoding venom in sea anemones. However, most of those genes are yet to be explored in an evolutionary context. Insulin is a common peptide across metazoans and has been coopted into a predatory venom in many venomous lineages. In this study, we focus on the diversity of insulin-derived venoms in sea anemones and on elucidating their evolutionary history. We sourced data for 34 species of sea anemones and found sequences belonging to two venom families that have Insulin PFAM annotations (Cono-Insulin, VP302). Our findings show that both families have undergone duplication events. Members of each of the independently evolving clades have consistent predicted protein structures and distinct dN/dS values. Our work also shows that VP302 is part of a multidomain venom contig and has experienced a secondary gain into the venom system of cuticulate sea anemones.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

Overexpression of a constitutively active truncated form of OsCDPK1 (OEtr) in rice produced smaller seeds, but a double-stranded RNA gene-silenced form of OsCDPK1 (Ri) yielded large seeds, suggesting that OsCDPK1 plays a functional role in rice seed development. In the study presented here, we propose a model in which OsCDPK1 plays key roles in negatively controlling the grain size, amylose content, and endosperm appearance, and also affects the physicochemical properties of the starch. The dehulled transgenic OEtr grains were smaller than the dehulled wild-type grains, and the OEtr endosperm was opaque and had a low amylose content and numerous small loosely packed polyhedral starch granules. However, the OEtr grain sizes and endosperm appearances were not affected by the temperature being either optimal (25 °C ) or low (22 °C) or high (31 °C) during the grain-filling phase. In contrast, the transgenic Ri grains were larger, had higher amylose contents, and had more transparent endosperms filled with tightly packed polyhedral starch granules. This demonstrates that OsCDPK1 plays a novel functional role in starch biosynthesis during seed development and affects the transparent appearance of the endosperm. These results improve our understanding of the molecular mechanisms through which the grain filling process occurs in rice.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

This work describes practical immunization of European sea bass (Dicentrarchus labrax) juveniles against viral nervous necrosis virus (VNNV), a betanodavirus causing worldwide mortalities in many fish species. Protection was obtained with the so called spinycterin vehicles consisting in irreversibly DNA-damaged DNA-repair-less E.coli displaying at their surface a downsized antigen. In this work we, i) maximized bacterial expression levels by downsizing the C protein to a fragment (frgC91-220) containing most of its antigenicity, ii) developed an scalable autoinduction bacterial media based in soy-bean increasing membrane display and reproducibility, iii) enriched surface expression by screening different anchors from several prokaryotic origins (anchor+frgC91-220), iv) preserved frgC91-220 antigenicity by inactivating bacteria by irreversible DNA-damage by means of Ciprofloxacin, and v) increased safety using a repair-less E.coli strain as spinycterin chassis. These second generation of spinycterins protected fish against VNNV challenge with partial (Nmistic+frgC91-220) or 100 % (YBEL+frgC91-220 ) protection, in contrast to those fish immunized with frgC91-220 spinycterins. The proposed spinycterin platform has high levels of environmental safety and cost effectiveness, thus providing potential for small fish vaccines for sustainable aquaculture.

Studying the interaction between the upper ocean and the typhoons is crucial to improve our understanding of heat and momentum exchange between the ocean and the atmosphere. In recent years, the upper ocean responses to typhoons have received considerable attention. The sea surface cooling (SSC) process has been repeatedly discussed. In the present work, case studies were examined on five strong and super typhoons that occurred in 2016—LionRock, 1610; Meranti, 1614; Malakas, 1616; Megi, 1617; and Chaba 1618—to search for more evidence and new features of typhoon’s impact on the sea surface environment. The typhoon monitoring data from the Central Meteorological Observatory, the sea surface temperature (SST) data from satellite microwave and infrared remote sensing, and the sea surface height anomaly (SSHA) data from satellite altimeters were used to analyze in detail: the SSC features caused by typhoons, the relationship between the SSC and the typhoon travelling speed, and the variations in cold and warm eddies during typhoon passage. Results showed that: (1) SSC generally occurred during typhoon passage and the degree of SSC was always determined by the strength and the travelling speed of the typhoon, as well as the initial SST. (2) One day before or on the day of typhoon passage, the SSHA slightly increased due to low surface pressure. After the typhoon passed, the SSHA obviously decreased along with the SSC. The pre-existing positive SSHAs, which always represent warm eddies, decreased or disappeared during typhoon passage, whereas negative SSHAs or cold eddies were enhanced. (3) New cold eddies were generated, especially at the turning points of the typhoon path. The presence of warm eddies is suggested to have a strengthening effect on the typhoons.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

Tropical sea surface temperature (SST) variability, mainly driven by the El Niño–Southern Oscillation (ENSO), influences the atmospheric circulation and hence the transport of heat and chemical species in both the troposphere and stratosphere. This paper uses Met Office, ERA5 and MERRA2 reanalysis data to examine the impact of SST variability on the dynamics of the polar stratosphere and ozone layer over the period 1980 to 2020. Particular attention is paid to studying the differences in the influence of different types of ENSO (East Pacific (EP) and Central Pacific (CP)) for the El Niño and La Niña phases. It is shown that during the EP El Niño, the zonal wind weakens more strongly and changes direction more often than during the EP El Niño, and the CP El Niño leads to a more rapid decay of the polar vortex (PV), an increase in stratospheric air temperature and an increase in the concentration and total column ozone than during EP El Niño. For the CP La Niña, the PV is more stable, which often leads to a significant decrease in Arctic ozone. During EP La Niña, powerful sudden stratospheric warmings are often observed, which lead to the destruction of PV and an increase in column ozone.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

The quantification of sea surface temperature (SST) through space platforms has revolutionized how we obtain information at a global level. However, the main disadvantage of obtaining SST with satellite images consists of its inherent coarse spatial resolution. One solution could be the use of downscaling algorithms to create sequences of matrices at a higher resolution. We used the same SST data source from the MODIS-Aqua sensor at three spatial resolutions of 9 km, 4.5 km, and 1 km in the Gulf of California. Based on an open-source algorithm, the original SST images were downscaled to 4.5 km, 1 km, 500 m, 250 m, and 125 m per pixel scales. Results indicate a strong linear relationship between the original SST-MODIS data and the modeled data for all spatial resolutions. This study demonstrates the feasibility of an open-source downscaling algorithm to enhance the spatial resolution of SST images in a marginal sea.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

The anomaly detection task is very important in computer science. And there are a lot of anomaly detection methods. Different from some thresholding methods, some unsupervised methods could make us get more accurate and faster result, which is the object of the project. In this paper, I tried to use EWMA and some other methods in two datasets: Webank time consuming indicators dataset and AIOps Challenge dataset. The paper consists nine parts: background of the project, related work, description of algorithms, implementation details, experimental setup and data sets used, experimental results and discussion, future directions, reference and meeting notes.

Anomaly detection and segmentation aim at distinguishing abnormal images from normal images and further localizing the anomalous regions. Feature reconstruction based method has become one of the mainstream methods for this task. This kind of method has two assumptions: (1) The features extracted by neural network is a good representation of the image. (2) The autoencoder solely trained on the features of normal images cannot reconstruct the features of anomalous regions well. But these two assumptions are hard to meet. In this paper, we propose a new anomaly segmentation method based on feature reconstruction. Our approach mainly consists of two parts: (1) We use a pretrained vision transformer (ViT) to extract the features of the input image. (2) We design a self-attention autoencoder to reconstruct the features. We regard that the self-attention operation which has a global receptive field is beneficial to the methods based on feature reconstruction both in feature extraction and reconstruction. The experiments show that our method outperforms the state-of-the-art approaches for anomaly segmentation on the MVTec dataset. It is both effective and time-efficient.

Cardiovascular diseases are a broadly understood concept focusing on vascular and heart dys-function. Lack of physical exercise, type 2 diabetes, obesity, hypertension, dyslipidemia, throm-boembolism, kidney, and lung diseases all contribute to the development of heart and blood vessel dysfunction. Although effective and important, traditional treatment with diuretics, statins, beta–blockers, calcium inhibitors, ACE inhibitors, and anti–platelet drugs remain a second–line treatment after dietary intervention and lifestyle changes. Scientists worldwide are still looking for an herbal product that would be quite effective and free from side effects, either taken together or before the standard pharmacological intervention. Such herbal–originated medication therapy may include Morus alba L. (white mulberry), Elaeagnus rhamnoides (L.) A. Nelson (sea–buckthorn), Allium sativum L. (garlic), Convallaria majalis L. (lily of the valley), Leonurus cardiaca L. (mother-wort), and Crataegus spp. (hawthorn). Valuable herbal raw materials include leaves, fruits, seeds, and even thorns. This short review focuses on six herbs that can constitute an interesting and po-tential therapeutic option in the management of cardiovascular disorders.

In the context of precision agriculture (PA), geomatic surveys exploiting UAV platforms allow the trees’ dimensional characterization and crown identification. This paper focuses on the use of low-cost UAV photogrammetry to estimate the trees’ height, as part of a project for the phytoremediation of contaminated soils. Two study areas (Area 1; Area 2) have been chosen, having different characteristics in terms of mean trees’ height (5 m; 0.7 m), to test the procedure even in a challenging context. Three campaigns have been performed in Area 1 at different altitudes (30 m, 40 m, 50 m), and one UAV flight is available in Area 2 (42 m of altitude). The implemented workflow involves the elaboration of the UAV point clouds and DSMs using the standard SfM approach, the vegetation filtering, the generation of the DTM and a GIS-based analysis to obtain the CHMs for the extraction of the trees’ heights based on a local maxima approach. UAV-derived heights have been compared with in-field measurements obtaining promising results in Area 1, confirming the applicability of the procedure for trees’ height extraction, while the application in the context of low trees was more problematic.

Hypersonic aircraft focuses more on the integration of aircraft and engine than ordinary aircraft owing to high performance requirements, and the nozzle design is reflected in the required large area ratio of nozzle inlet and outlet and the compactness of the overall size of the aircraft. In this study, the height constraint is directly introduced into the maximum thrust nozzle design method. A new method for designing nozzles under the height constraints that consults the maximum thrust theory is proposed. Initially, the condition that the nozzle reaches the maximum thrust under the height constraint is deduced mathematically. Then, a nozzle design method satisfying the height constraint is computed using the method of characteristics (MOC). Subsequently, the influence of the design parameters on the design method is studied parametrically. Results show that Mach number scale and asymmetrical factors can affect ramp length and flap length of the nozzle, respectively. These factors great influence the axial thrust performance and lift under a specific height constraint. Compared with the traditional truncation design method, the thrust coefficient and lift increased by 11.93% and 138.45% respectively.

The combined muscle-skeletal traumas (MST) are very frequent over the last few years. The emergency care try to save the life of the patient and to receive resuscitation treatment. The role of Trauma surgeon is to choose the right moment for surgery. Aim: To present the management of patient with combined height injury, fracture stabilization, partial foot amputation, local flaps, skin grafting and HIFU – thermotherapy as scar treatment. Materials and methods: 40 years old mail patient, injured after a fall from 8 meters in an elevator shaft. After resuscitation treatment to control the shock the Imaging results are: burst fracture of L3 with spinal canal stenosis, fracture of the sacral bone Denis I, fracture of the right humerus in the proximal third, Monteggia fracture of the left arm, fracture of the proximal third of the right tibia as well as comminuted fractures of both calves and of both heel bones. Results: After a few operations his final result was well healed bone fractures and a good quality soft tissue coverage allowing the patient a satisfactory quality of life. Conclusions: Combined traumas of the muscle- skeletal system are severe, serious and difficult to manage. The good outcome in their treatment requires a team approach between the different medical specialists.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

In this paper, we presented a method of retrieving sea surface wind speed from Sentinel-1 synthetic aperture radar (SAR) horizontal-horizontal (HH) polarization data in extra-wide mode, which have been extensively acquired over the Arctic for sea ice monitoring. In contrast to the conventional algorithm, i.e., using a geophysical model function (GMF) to retrieve sea surface wind by spaceborne SAR, we introduced an alternative method based on physical model guided neural network. Parameters of SAR normalized radar cross section, incidence angle, and wind direction are used as the inputs of the backward propagation (BP) neural network, and the output is the sea surface wind speed. The network is developed based on more than 11,000 HH-polarized EW images acquired in the marginal ice zone (MIZ) of the Arctic and their collocations with scatterometer measurements. Verification of the neural network based on the testing dataset yields a bias of 0.23 m/s and a root mean square error (RMSE) of 1.25 m/s compared to the scatterometer wind speed. Further comparison of the SAR retrieved sea surface wind speed with independent buoy measurements shows a bias and RMSE of 0.12 m/s and 1.42 m/s, respectively. We also analyzed the uncertainty of retrieval when the wind direction data of a reanalysis model are used as inputs to the neural network. By combining the detected sea ice cover information based on the EW data, one can expect to derive simultaneously sea ice and marine-meteorological parameters by spaceborne SAR in a high spatial resolution in the Arctic.

The main objective of this study is to search better prediction result of rainy seasonal rainfall (15 June-15 August). A correlation between rainfall of Bengali rainy seasons at Rangpur, Dhaka, Barisal and Sylhet and global sea surface temperature (SST) of different areas of the world was studied by using the both data of 1975- 2008 years with the help of the Climate Predictability Tool (CPT) to find more positive correlated SST with observed rainfall and use as predictor for giving the prediction of the year 2009. Using SST of one month before rainy season as predictor, the positive deviation of predicted rainfall from observed rainfall was 1.34 mm/day at Sylhet and 0.9 mm/day at Dhaka. The negative deviation of mean rainfall was 1.16 mm/day at Rangpur and 1.10 mm/day at Barisal. Again, using of starting one month SST of rainy season as predictor, positive deviation of predicted rainfall from observed rainfall was 4.03 mm/day at Sylhet. The positive deviation of daily mean rainfall was found 6.58 mm/day at Dhaka and 6.23 mm/day over southern Bangladesh. The study reveals that sea surface temperature (SST) of one month before rainy season was better predictor than SST of starting month of rainy season.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

By shifting the focus from aggregate-level analysis to individual-level analysis, we believe that the DAD model can contribute to a more comprehensive understanding of driving behavior. Combing DAD with a conflict identification (CIM) model can potentially enhance the effectiveness of Advanced Driver Assistance Systems (ADAS) in terms of crash evasion capabilities. This paper is part of our research titled Automatic Safety Diagnosis in Connected Vehicle Environment, which received funding from the Southeastern Transportation Research, Innovation, Development, and Education Center.

Predicting anomalies in manufacturing assembly lines is crucial for reducing time and labor costs and improving processes. For instance, in rocket assembly, premature part failures can lead to significant financial losses and labor inefficiencies. With the abundance of sensor data in the Industry 4.0 era, machine learning (ML) offers potential for early anomaly detection. However, current ML methods for anomaly prediction have limitations, with F1-measure scores of only 50% and 66% for prediction and detection, respectively. This is due to challenges like the rarity of anomalous events, scarcity of high-fidelity simulation data (actual data is expensive), and the complex relationships between anomalies not easily captured by traditional ML approaches. Specifically, these challenges relate to two dimensions of anomaly prediction: predicting when anomalies will occur and understanding the dependencies between them. This paper introduces a new method called Robust and Interpretable 2D Anomaly Prediction (RI2AP) designed to address both dimensions effectively. RI2AP is demonstrated on a rocket assembly simulation, showing up to a 30-point improvement in F1 measure compared to current ML methods. This highlights its potential to enhance automated anomaly prediction in manufacturing. Additionally, RI2AP includes a novel interpretation mechanism inspired by a causal-influence framework, providing domain experts with valuable insights into sensor readings and their impact on predictions. Finally, the RI2AP model is deployed in a real manufacturing setting for assembling rocket parts. Results and insights from this deployment demonstrate the promise of RI2AP for anomaly prediction in manufacturing assembly pipelines.

Glaucoma secondary to Peters' anomaly (PA) is an important factor affecting visual prognosis, but there are few reports on it. This study aimed to investigate the characteristics of glaucoma asso-ciated with PA and glaucoma surgery outcomes. This retrospective study included 31 eyes of 20 patients with PA. PA was classified into three stages: Stage 1, with a posterior corneal defect only; Stage 2, a corneal defect with iridocorneal adhesion; and Stage 3, a corneal defect with lens ab-normalities. The associations between glaucoma and anterior segment dysgenesis severity, visual prognosis, and glaucoma surgery outcomes were analyzed. Sixteen eyes of 10 patients developed glaucoma. Stage 1 PA had no glaucoma, 52% of Stage 2 had glaucoma, and 75% of Stage 3 had glaucoma. Of the 16 eyes with glaucoma, 11 underwent surgery. Eight of these 11 eyes achieved intraocular pressure (IOP) control. Five of the nine eyes that underwent trabeculotomy (TLO) succeeded, and none had corneal staphyloma. Three of the four eyes for which TLO was ineffective had corneal staphyloma (P=0.0331). Patients with PA are more likely to develop glaucoma as anterior segment dysgenesis progresses, and the effect of TLO is limited if corneal staphyloma is present.

The properties of the dark matter, dark energy, graviton and photon are discussed in terms of the new three-dimensional quantized space model. Three new particles (bastons) with the electric charges (EC) are proposed as the dark matters. It is proposed that the EC, LC and CC charges are aligned along the time axes but not along the space axes. The photon is confined on its corresponding three-dimensional quantized space. However, the graviton can be evaporated into other three-dimensional quantized spaces. The rest mass of the electron neutrino (n_e) of 3.494·10⁻³ eV/c² is obtained from the experimental vacuum energy density in terms of quantum field theory (QFT). The rest mass and force range of the massive g(0,0,0) graviton with the Planck size are m_g = 3.1872·10⁻³¹ eV/c² and x_r = 3.0955·10²³ m = 10.0 Mpc, respectively, based on the experimental rest mass and rms charge radius of the proton. The possible diameter (10 Mpc) of the largest galaxy cluster is remarkably consistent with the gravitational force range (10 Mpc). Then, the diameter of the largest dark matter distribution related to the largest galaxy cluster is 9.2865·10²³ m = 30 Mpc equal to the force range of the massive g(0) graviton with the rest mass of 1.0624·10⁻³¹ eV/c². Because of the huge number (N) of the evaporated gravitons, the very small Coulomb’s constant of about 10⁻⁴⁸k and large gravitation constant of 10⁶G_N are expected for the charged dark matters. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = 0 for the proton-like particle. The proposed weak gravitational force between the dark matters and normal matters explains the observed dark matter distributions of the bullet cluster, Abell 1689 cluster and Abell 520 cluster. The transition from the galaxy without the dark matters to the galaxy with the dark matters are explained. Also, the accelerated space expansion is caused by the new space quanta created by the evaporated gravitons into the x1x2x3 space and repulsive electromagnetic force between dark matters corresponding to the dark energy. The decreasing coupling constant of the strong force, neutron lifetime anomaly and the pressure distribution inside the proton are explained by the unobservable proton and hadronization. And the rest mass of 1.4 TeV/c² is assigned to the Le particle with the EC charge of −2e. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. Also, the gravitation constant has been changing with the time because of the graviton evaporation.

Mixing layer height (MLH) is a crucial parameter for air quality modelling that is still not routinely measured. Common methods for MLH determination use atmospheric profiles recorded by radiosonde but they suffer from course temporal resolution since balloon launching is only twice a day. Recently cheap ceilometers are gaining popularity in the retrieval of MLH diurnal evolution based on aerosol profiles. This study presents a comparison of a proprietary (Jenoptik) and a free available (STRAT) algorithms to retrieve MLH diurnal cycle. The comparison is accomplished in summer season over urban area and radiosonde data is used to estimate MLHs according to parcel, lapse rate, and Richardson methods (the last algorithm is used as a reference in the study) in addition. It was found that STRAT and Jenoptik give lower MLH than radiosonde with an underestimation of about 150m and 650m respectively. Additionally, STRAT showed reasonable performance in tracking of MLH diurnal evolution. Daily MLH maximum of about 2000m was found in the late afternoon (18-19 LT). In contrast, Jenoptik algorithm showed more weaknesses, mainly attributed to its real-time operation and independent processing of a single profile. At night and during morning transition period, both lidar-based methods showed difficulties as MLH was often in the ceilometer’s incomplete overlapping zone so residual or advected aerosol layers aloft were misleadingly reported as mixing layer (ML).

Rice canopy height and density are directly usable crop phenotypic traits for the direct estimation of crop biomass. Therefore, it is crucial to rapidly and accurately estimate rice canopy phenotypic parameters. To achieve non-destructive detection and estimation of essential phenotypic parameters in rice, a platform based on LiDAR point cloud data for rice phenotypic parameter detection was established. Data collection of rice canopy layers was performed across multiple plots. The LiDAR-detected canopy top point clouds were selected using a method based on the highest percentile, and the rice canopy surface model was calculated. Canopy height estimation was the difference between ground elevation and percentile value. To determine the optimal percentile defining the rice canopy top, testing was conducted incrementally from 0.8 to 1 with an increment of 0.005. The optimal percentile value was found to be 0.975. The root mean square error (RMSE) between LiDAR-detected canopy height and manually measured canopy height was calculated. The prediction model based on canopy height (R2=0.941, RMSE=0.019) exhibited a strong correlation with actual canopy height. Linear regression analysis was conducted between gap fraction of different plots and manually detected average Leaf Area Index (LAI) of rice canopy. Prediction models for canopy LAI based on ground return counts (R2=0.24, RMSE=0.1) and ground return intensity (R2=0.28, RMSE=0.09) showed strong correlations but had lower correlation with rice canopy LAI. Regression analysis was performed between LiDAR-detected canopy height and manually measured rice canopy LAI. The results indicated that the prediction model based on canopy height (R2=0.77, RMSE=0.03) was more accurate.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

Sea ice roughness can serve as a proxy for other sea ice characteristics such as ice thickness and ice age. Arctic-wide maps that represent spatial patterns of sea ice roughness can be used to better characterize spatial patterns of ice convergence and divergence processes. Sea ice surface roughness can also control and quantify turbulent exchange between sea ice surface and atmosphere and therefore influence surface energy balance at the basin scale. We have developed a data processing system that produces georeferenced sea ice roughness rasters that can be mosaicked to produce Arctic-wide maps of sea ice roughness. This approach starts with Top-of-Atmosphere radiance data from the Multi-angle Imaging SpectroRadiometer (MISR). We used red-band angular data from three MISR cameras (Ca, Cf, An). We created a training data set in which MISR pixels were matched with co-located and concurrent lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). We used a K-nearest neighbor algorithm with the training data to calibrate the multi-angle data to values of surface roughness and then applied the algorithm to Arctic-wide MISR data for two 16-day periods in April (spring) and July (summer). After georeferencing the roughness rasters, we then mosaicked each 16-day roughness dataset to produce Arctic-wide maps of sea ice roughness for spring and summer. Assessment of the results shows good agreement with independent ATM roughness data, not used in model development. A preliminary exploration of spatial and seasonal changes in sea ice roughness for two locations shows the ability to characterize the roughness of different ice types and the results align with previous studies. This processing system and its data products can help the sea ice research community to gain insights into the seasonal and interannual changes in sea ice roughness over the Arctic.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r&gt;0.90) and peri-urban (HWM, HWA, r&gt;0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

The rapid evolution of information and communication technologies, notably the Internet, has yielded substantial benefits while posing challenges to information system security. With an increasing frequency of cyber threats—from unauthorized access to data breaches—the digital landscape's vulnerability is evident. Addressing the financial impact of cybercrime, this study delves into the role of Artificial Intelligence (AI) and Machine Learning (ML) technologies in cybersecurity. Analyzing advancements and outcomes, the research explores practical techniques for anomaly detection, threat prediction, and automated response. By investigating prior research and real-world implementations, the study provides valuable insights into the potential of AI/ML, uncovering current trends, challenges, and prospects in enhancing cybersecurity tactics amid a dynamically changing threat landscape.

Foundational and state-of-the-art anomaly detection methods through power system state estimation are reviewed. The traditional components for bad data detection such as chi-square testing, residual-based methods, and hypothesis testing are discussed to explain the motivations for recent anomaly detection methods given the increasing complexity of power grids, energy management systems, and cyber-threats. In particular, state estimation anomaly detection based on data-driven quickest change detection and artificial intelligence are discussed and directions for research are suggested with particular emphasis on considerations of the future smart grid.

In recent years, video anomaly detection technology , which can intelligently analyze massive video and quickly find abnormal phenomena, has attracted extensive attention with the wide application of video surveillance technology . To address the complex and diverse problem of abnormal human behavior detection in surveillance videos, a surveillance video abnormal behavior detection and localization supervised method based on the deep network model and the traditional method is proposed. Specifically, we combined AGMM and YOLACT methods to obtain more accurate foreground information by fusing the foreground maps extracted by each technique. To further improve the accuracy , we use the PWC-Net technique to extract features of the foreground images and input them into an anomaly classification model for classification. The proposed method effectively detects and locates the abnormal behavior in the monitoring scene. In addition to the aforementioned methods, this paper also employs YOLOV5 and DeepSORT networks for object detection and tracking in the video, which allows us to track the detected objects for better understanding of the scene in the video. Experiments on the UCSD benchmark dataset and the comparison with state-of-the-art schemes prove the advantages of our method.

Hyperspectral anomaly detection is to recognize anomalies from complex scene in an unsupervised way. Currently, many spectral-spatial detection methods have been proposed with a cascaded manner. However, they often neglect complementary characteristics between spectral and spatial dimensions, which easily leads to yield high false alarm rate. To alleviate this issue, a spectral-spatial information fusion (SSIF) method is designed for hyperspectral anomaly detection. First, an isolation forest is exploited to obtain spectral anomaly map, in which the object-level feature is constructed with entropy rate segmentation algorithm. Then, a local spatial saliency detection scheme is proposed to produce spatial anomaly result. Finally, the spectral and spatial anomaly scores are integrated together followed by a domain transform recursive filtering to generate the final detection result. Experiments on five hyperspectral datasets prove that the proposed SSIF produces superior detection result over other state-of-the-art detection techniques.

There are many applications of anomaly detection in IoT domain. IoT technology consists of large number of interconnecting digital devices not only generating huge data continuously but also making real-time computations. Since IoT devices are highly exposed due to Internet, they frequently meet with the challenges of illegitimate accesses in the form of intrusions, anomaly, fraud, etc. Identifying these illegitimate accesses in IoT domain can be an exciting research problem. In numerous applications fuzzy clustering and rough set theory have been successfully employed. As the data generated in IoT domains are high-dimensional, the clustering methods used for lower dimensional data cannot be applied efficiently. In this article, mixed approaches consisting of nano topology and fuzzy clustering techniques are proposed for anomaly detection. First of all, the nano topology is generated to find lower dimensional apace and then a couple of well-known fuzzy clustering techniques are employed on it for the efficient anomaly detection. The effectiveness of the proposed approaches is evaluated using time-complexity analysis, experimental studies with a synthetic dataset and a real-life dataset along with comparative studies with traditional fuzzy clustering approaches namely fuzzy c-means clustering (FCM) algorithm, Gustafson-Kessel (GK) Algorithm, Gath-Geva (GG) Algorithm, Mahalanobis Distance based Fuzzy C-Means algorithm (M-FCM), and Common Mahalanobis Distance based Fuzzy C-Means algorithm (CM-FCM). Experimentally, it has been found that the proposed approaches outperform the aforesaid algorithms in terms of detection rates, accuracy rates, false alarm rates and computational times.

Log collection and storage is a crucial process for enterprises around the globe. Log analysis helps identify potential security breaches and, in some cases, is required by law for compliance. However, enterprises often delegate these responsibilities to third-party Cloud Service Providers (CSPs), where the logs are collected and processed for anomaly detection and stored in a data warehouse for archiving. Prevalent schemes rely on plain (unencrypted) data for anomaly detection. More often, these logs can reveal sensitive information about an organization or the customers of that organization. Hence, it is best to keep it encrypted at all times. This paper presents "SigML++," an extension of work done in "SigML." We utilize Fully Homomorphic Encryption (FHE) with the Cheon-Kim-Kim-Song (CKKS) scheme for supervised log anomaly detection on encrypted data. We use an Artificial Neural Network (ANN) based probabilistic polynomial approximations using a Perceptron with linear activation. We probabilistically approximate the Sigmoid activation function (σ(x)) in the encrypted domain for the intervals [−10,10] and [−50,50]. Experiments show better approximations for Logistic Regression (LR) and Support Vector Machine (SVM) for low-order polynomials.

Pipeline integrity is an important area of concern for the oil and gas, refining, chemical, hydrogen, carbon sequestration, and electric-power industries, due to the safety risks associated with pipeline failures. Regular monitoring, inspection, and maintenance of these facilities is therefore required for safe operation. Large standoff magnetometry (LSM) is a non-intrusive, passive magnetometer-based mea- surement technology that has shown promise in detecting defects (anomalies) in regions of elevated mechanical stresses. However, analyzing the noisy multi-sensor LSM data to clearly identify regions of anomalies is a significant challenge. This is mainly due to the high frequency of the data collection, mis-alignment between consecutive inspections and sensors, as well as the number of sensor measurements recorded. In this paper we present LSM defect identification approach based on ma- chine learning (ML). We show that this ML approach is able to successfully detect anomalous readings using a series of methods with increasing model complexity and capacity. The methods start from unsupervised learning with "point" methods and eventually increase complexity to supervised learning with sequence methods and multi-output predictions. We observe data leakage issues for some methods with randomized train/test splitting and resolve them by specific non-randomized splitting of training and validation data. We also achieve a 200x acceleration of support-vector classifier (SVC) method by porting computations from CPU to GPU leveraging the cuML RAPIDS AI library. For sequence methods, we develop a customized Convolutional Neural Network (CNN) architecture based on 1D convolutional filters to identify and characterize multiple properties of these defects. In the end, we report the scalability of the best-performing methods and compare them, for viability in field trials.

Automation of forest field reference data collection has been an intensive research objective for laser scanning scientists ever since the invention of terrestrial laser scanning more than two decades ago. Recently, it has been proposed that such automated data collection providing both the tree heights and stem curves would require a combination of above-canopy UAV point clouds and terrestrial point clouds. In this study, we demonstrate that an under-canopy UAV laser scanning system utilizing a rotating laser scanner can alone provide accurate estimates of the canopy height and the stem volume for the majority of the trees in a boreal forest. To this end, we mounted a rotating laser scanner based on a Velodyne VLP-16 sensor onboard a manually piloted UAV. The UAV was commanded with the help of a live video feed from the onboard camera of the UAV. Since the system was based on a rotating laser scanner providing varying view angles, all important elements such as treetops, branches, trunks, and ground could be recorded with laser hits. In an experiment including two different forest structures, namely sparse and obstructed canopy, we showed that our system can measure the heights of individual trees with a bias of -20 cm and a standard error of 40 cm in the sparse forest and with a bias of -65 cm and a standard error of 1 m in the obstructed forest. The accuracy of the obtained tree height estimates was equivalent to airborne above-canopy UAV surveys conducted in similar forest conditions. The higher underestimation and higher inaccuracy in the obstructed site can be attributed to three trees with a height exceeding 25 m and the applied laser scanning system VLP-16 that had a limited height measurement capacity when it comes to trees taller than 25 m. Additionally, we used our system to estimate the stem volumes of individual trees with a standard error at the level of 10%. This level of error is equivalent to the error obtained when merging above-canopy UAV laser scanner data with terrestrial point cloud data. Future research is needed for testing new sensors, for implementing autonomous operation inside canopies through collision avoidance and navigation through canopies, and for developing robust methods that work also with more complex forest structure. The results show that we do not necessarily need a combination of terrestrial point clouds and point clouds collected using above-canopy UAV systems in order to accurately estimate the heights and the volumes of individual trees.

This study presents a world review as well as new additional data in form of submerged speleothems that are used for paleo sea level reconstructions. Speleothems significantly contributed to the understanding of the global and regional sea level variations during the Middle and Late Quaternary. The studied speleothems cover the last 1.4 Myr and are focused mainly on Marine Isotope Stages (MIS) 1, 2, 3, 5.1, 5.3, 5.5, 7.1, 7.2, 7.3 and 7.5. Results reveal that submerged speleothems represent extraordinary archives providing detailed information on former sea level changes. We present also new results from stalactites collected in central Mediterranean sea, at Favignana and Ustica islands (Sicily, Italy), both characterized by continental, phreatic or marine layers. The study and analysis of the latter speleothems provide results of great interest for relative sea level changes over the last 1000 years.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

Approximately 20% of the world's population resides in coastal areas at risk of rising sea levels due to climate change. This could lead to severe weather events and ecological impact on critical infrastructure. To combat the effects of water-based environmental forces on the land, hard engineering methods such as seawalls have been utilized. However, a more sustainable solution is emerging in nature-based engineering, which involves growing vegetation. This approach can help extend the lifespan of existing technology and provide climate change adaptation and resilience for coastal and riverine communities. The following paper will review seaweed farms as an advanced nature-based mitigation approach. The paper also outlines the findings of experiments at RWTH Aachen University's hydraulic laboratory. These tests involved using seaweed as a natural solution to dampen waves in a model system to test a hypothesis. One result involving a system with two lines of seaweed revealed 15 percent wave damping. Using seaweed as a nature-based solution, a gentle engineering approach to designing future vegetated protection systems can extend the design life of existing coastal infrastructure. This can also provide protection against climate-induced sea level rise, promote coastal risk mitigation, restore ecosystems, and foster blue bio-economic development.

Anomaly Detection in real time data is accepted as a vital research area. Clustering has effectively been tried for this purpose. As the datasets are real time, the time of generating of the data is also important. In this article, we introduce a mixture of partitioning and agglomerative hierarchical approach to detect anomalies from such datasets. It is a two-phase method which follows partitioning approach first and then agglomerative hierarchical approach. The dataset can have mixed attributes. In phase-1, a unified metric defined on mixed attributes is used. The same is also used for merging of similar clusters in phase-2. Also, we have kept the track of time attribute of each data instance which produces the clusters with their lifetimes in phase-1. Then in phase-2, we merge the similar clusters. While merging, the similar clusters, the lifetimes of the corresponding clusters with overlapping cores are to be superimposed producing fuzzy time intervals. This way, each cluster will have an associated fuzzy lifetime. The data instances either belonging sparse clusters or not belonging to any of the clusters can be treated as anomalies. The efficacy of the algorithms can be established using both complexity analysis as well as experimental studies.

Anomaly detection is an active area of research with numerous methods and applications. This survey reviews the state-of-the-art of data-driven anomaly detection techniques and their application to the the aviation domain. After a brief introduction to the main traditional data-driven methods for anomaly detection, we review the recent advances in the area of neural networks, deep learning and temporal-logic based learning. We cover especially unsupervised techniques applicable to time series data because of their relevance to the aviation domain, where the lack of labeled data is the most usual case, and the nature of flight trajectories and sensor data is sequential, or temporal. The advantages and disadvantages of each method are presented in terms of computational efficiency and detection efficacy. The second part of the survey explores the application of anomaly detection techniques to aviation and their contributions to the improvement of the safety and performance of flight operations and aviation systems. As far as we know, some of the presented methods have not yet found an application in the aviation domain. We review applications ranging from the identification of significant operational events in air traffic operations to the prediction of potential aviation system failures for predictive maintenance.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

This manuscript employs a surface stress-driven nonlocal model to explore the combined effects of long-range interaction and surface energy on higher vibration modes of functionally graded nanobeams. The nanobeam theory, based on Bernoulli-Euler kinematics, incorporates surface effects such as surface elasticity, surface residual stresses, surface density, and rotary inertia. Hamilton's principle is applied to derive the governing equation with size-dependent considerations. The main outcomes of a parametric investigation, considering four different kinematic boundary conditions (Cantilever, Simply-Supported, Clamped-Pinned, and Doubly-Clamped) while varying the nonlocal parameter and material gradient index, are presented and discussed. Additionally, the normalized natural frequencies for the second, third, fourth and fifth modes of vibrations are provided and analyzed for each case under study. The results underscore the model's effectiveness in capturing surface energy effects on the overall dynamic behavior of functionally graded Bernoulli-Euler nanobeams, offering a cost-effective approach for designing and optimizing nano-scaled structures.

Wave buoy measurements were carried out near the north-eastern Black Sea coast at the natural reserve Utrish in 2020-2021. In total, about 11 months of data records were collected during two stages of the experiment at 600 and 1500 meters offshore and depths of 18 and 42 meters. The measured waves propagate almost exclusively from the seaward directions. Generally, the waves do not follow the local wind directions, thus, implying a mixed sea state. Nevertheless, dimensionless wave heights and periods appears to be quite close to the previously established empirical laws for the wind-driven seas. The results of the wave turbulence theory are applied for estimates of spectral energy fluxes and their correspondence to the energy flux from the turbulent wind pulsations. These estimates are consistent with today's understanding of wind-wave interaction. It is shown that the main fraction of the wind energy flux goes to the direct Kolmogorov-Zakharov cascade to high wave frequencies and then to dissipation in small scales. Less than 1% of the wind energy flux is directed to low frequency band (the so-called inverse Kolmogorov-Zakharov cascade), thus, providing wave energy growth.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Maritime Continent (MC) positions in between Asian and Australian summer monsoons zone. Its complex topography and shallow seas around it is a major challenge for the climate researchers to model and understand it. Monsoon in this area is affected by inter-scale ocean-atmospheric interactions like El-Niño Southern Oscillation (ENSO), Indian Ocean Dipole (IOD) and Madden-Julian Oscillation. Monsoon rainfall in MC (especially in Indonesia and Malaysia) profoundly exhibits its variability dependency on ocean-atmospheric phenomena in this region. This monsoon shift often introduces to dreadful events like biomass burning (BB) in Southeast Asia (SEA) which sometimes leads to severe trans-boundary haze pollution. In this study, the episode of BB in 2015 of SEA is highlighted and discussed. Observational satellite datasets are tested by performing simulations with numerical weather prediction (NWP) model using WRF-ARW (Advanced research WRF). Observed and model datasets are compared to study the sea surface temperature (SST) and precipitation (rainfall) anomalies influenced by ENSO, IOD and MJO. Correlations have been recognised which explains the delayed rainfall of regular monsoon in MC due to the influence of ENSO, IOD and MJO during 2015 BB episode, eventually leading to intensification of fire and severe haze.

Melatonin is a ubiquitous molecule found in living organisms, ranging from bacteria to plants and mammals. It possesses various properties, partly due to its robust antioxidant nature and partly owed to its specific interaction with melatonin receptors present in almost all tissues. Melatonin regulates different physiological functions and contributes to the homeostasis of the entire organism. In the human eye, a small amount of melatonin is also present, produced by cells in the anterior segment and the posterior pole, including the retina. In the eye, melatonin may provide antioxidant protection along with regulating physiological functions of ocular tissues, including intraocular pressure (IOP). Therefore, it is conceivable that the exogenous administration of sufficiently high amounts of melatonin to the eye could be beneficial in several instances: for the treatment of eye pathologies like glaucoma, due to the IOP-lowering and neuroprotection effects of melatonin; for the prevention of other dysfunctions, such as dry eye and refractive defects (cataract and myopia) mainly due to its antioxidant properties; for diabetic retinopathy due to its metabolic influence and neuroprotective effects; for macular degeneration due to the antioxidant and neuroprotective properties; and for uveitis, mostly owing to anti-inflammatory and immunomodulatory properties. This paper reviews the scientific evidence supporting the use of melatonin in different ocular districts and provides data suggesting that the topical administration of melatonin as eye drops is a real possibility. This way, its distribution and concentration in different ocular tissues may support its pleiotropic therapeutic effects.

(1) Background: A simple approach to map irrigated landcover has been introduced by using measures derived from optical spectral range as an alternative to thermal range. It has been demonstrated that substituting surface temperature (Ts, ‘thermal approach’) with SWIR transformed reflectance (STR, ‘optical approach’) to detect surface moisture is feasible with comparable results. (2) Methods: Using an iterative thresholding procedure to minimize within-class variance, the bilevel segmentation of variables derived from Landsat-8 representing surface moisture and vegetation cover was achieved for the 2020-21 summer for a key irrigation district in Australia. (3) Results: The results of irrigated landcover by optical approach found to be comparable with those by thermal approach. The classification accuracy was assessed using water delivery records at farm level. Though the overall accuracy is high in both cases, the optical approach (97.6%) performed slightly better than the thermal approach (93.9%). (4) Conclusions: The feasibility of using STR to map irrigated landcover has been confirmed by a high-level overall accuracy assessment. This has broader implications in terms of irrigated landcover assessment, as the use of satellite imagery in these applications may not necessarily be limited to microwave or thermal sensors.

Data from NASA’s Soil Moisture Active Passive Mission (SMAP) and from the California Cooperative Oceanic Fisheries Investigations (CalCOFI) were used to examine the freshening that occurred during 2015-2016 in the Southern California Current System. Overall the freshening was found to be related to the 2014-2016 Northeast Pacific Warm Anomaly. The primary goal was to determine the feasibility of using SMAP data to observe the surface salinity signal associated with the warming. As a first step direct comparisons were done with salinity from the CalCOFI data at one-meter depth. During 2015 SMAP was saltier than CalCOFI by 0.5 PSU, but biases were reduced to < 0.1 PSU during 2016. South of 33°N, and within 100 km of the coast, SMAP was fresher in 2015 by almost 0.2 PSU. CalCOFI showed freshening of 0.1 PSU. North of 33°N SMAP and CalCOFI saw significant freshening in 2016, SMAP by 0.4 PSU and CalCOFI by 0.2 PSU. Differences between SMAP and CalCOFI are consistent with the increased stratification in 2015 and changes in the mixed layer depth.

Phenotypic characterization of crop genotypes is an essential yet challenging aspect of crop management and agriculture research. Digital sensing technologies are rapidly advancing plant phenotyping and speeding-up crop breeding outcomes. However, off-the-shelf sensors might not be fully applicable and suitable for agriculture research due to diversity in crop species and specific needs during plant breeding selections. Customized sensing systems with specialized sensor hardware and software architecture provide a powerful and low-cost solution. This study designed and developed a fully integrated Raspberry Pi-based LiDAR sensor named CropBioMass (CBM), enabled by internet of things to provide a complete end-to-end pipeline. The CBM is a low-cost sensor, provides high-throughput seamless data collection in field, small data footprint, injection of data onto the remote server, and automated data processing. Phenotypic traits of crop fresh biomass, dry biomass, and plant height estimated by CBM data had high correlation with ground truth manual measurements in wheat field trial. The CBM is readily applicable for high-throughput plant phenotyping, crop monitoring, and management for precision agricultural applications.

Ebstein anomaly, a congenital heart condition, can manifest across a broad age spectrum, including adulthood. We present a unique case of a 67-year-old woman with no significant medical history who sought medical attention for severe headaches, vomiting, and respiratory distress, accompanied by elevated blood pressure and rapid pulse. Initial investigations, including troponin T levels, yielded unremarkable results. However, an electrocardiogram unveiled a right bundle branch block (RBBB) pattern, prompting further assessment. A subsequent chest X-ray disclosed an enlarged heart, indicating cardiomegaly, prompting echocardiography. The echocardiogram confirmed the diagnosis of Ebstein anomaly, revealing a 26 mm apical displacement of the tricuspid valve (TV). The patient was managed conservatively with supplemental oxygen and exhibited gradual improvement. This case underscores the infrequent occurrence of Ebstein anomaly in adulthood and underscores the necessity for thorough evaluation in cases of unexplained cardiopulmonary symptoms.

Finding anomalies in the real-time system is recognized as one of most challenging study in information security. It has so many applications like IoT, and Stock-Market. In any IoT system the data generated are real-time, and temporal in nature. Since due to the extreme exposure to Internet and interconnectivity of devices, the IoT systems often face issues like fraud, anomalies, intrusions etc. Discovering anomaly in such domain can be interesting. Clustering and rough set theory have been tried in many cases. Considering the time-stamp associated with IoT data, time-dependent patterns like periodic clusters can be generated which could be helpful for the efficient detection of anomalies by providing more in-depth analysis of the system. In this paper, a mixed method comprising of nano topology, a modified k-means clustering and an interval superimposition technique is used for finding fuzzy periodic clusters in the subspace generated by the nano topology. For every clusters there will be an associated sequence of time-intervals where it exists. The sequence time-intervals accompanying with each clusters may exhibit some remarkable patterns. For example, there may exist different types of periodicity namely yearly, monthly, daily, and hourly etc. For finding such fuzzy periodicity, an operation called interval-superimposition has been used. The time-intervals associated with each cluster are superimposed if they have reasonable overlapping. Each superimposed time-interval generates a fuzzy time-interval. The data instances are thought to be anomalous if they either belong to sparse clusters or don't belong to any clusters. The efficacy of the method can be assessed by means of both time-complexity analysis and comparative studies with existing clustering-based anomaly detection algorithms with a real-life and a synthetic dataset. It can been found experimentally that our method can extract anomaly with 98% of accuracy and it runs cubic time approximately.

The challenging issues of Computer Network and Databases are not only the intrusion detection but also the reduction of false positive and increase of detection rate. In any intrusion detection system, anomaly detection mainly focuses on modeling the normal behavior of the users and detecting the deviations from normal behavior which are assumed to be potential intrusions or treat. Several techniques have already been successfully tried for this purpose. However, the normal and suspicious behavior are hard to predict as there is no precise boundary differentiat-ing one from another. Here rough set theory and fuzzy set theory come into the picture. In this article, a hybrid approach based on rough set theory and intuitionistic fuzzy set theory is pro-posed for the detection of anomaly. The proposed approach is a classification approach which takes the advantages of softness properties both rough and fuzzy set theory to deal with uncer-tainty in the dataset. The algorithm classifies the data instances in such a way that they can be expressed using natural language. The experimental results with a real world dataset and a syn-thetic dataset show that the proposed algorithm has normal true positive rates of 91.989% and 96.99% and attack true positive rates of 91.289% and 96.29% respectively

Machine learning methods have widely been applied to detect anomalies in machine and cutting tool behavior during lathe or milling. However, detecting anomalies in the workpiece itself did not get the same attention by researchers. That is why in this article, the authors present a pub-licly available multivariate time series dataset which was recorded during milling of 16MnCr5. Due to artificially introduced, though realistic anomalies in the workpiece the dataset can be ap-plied for anomaly detection. By using a convolutional autoencoder as a first model good results in detecting the location of the anomalies in the workpiece were achieved. Furthermore, milling tools with two different diameters where used which led to a dataset eligible for transfer learn-ing. The objective of this article is to provide researchers with a real-world time series dataset of the milling process which is suitable for modern machine learning research topics like anomaly detection and transfer learning.

The rapid industrial growth in solar energy is gaining increasing interest in renewable power from smart grids and plants. Anomaly detection in photovoltaic (PV) systems is a demanding task. In this sense, it is vital to utilize recent advances in machine learning to accurately and timely detect different anomalies and condition monitoring. This paper addresses this issue by evaluating different machine learning techniques and schemes and showing how to apply these approaches to solve anomaly detection and detect faults on photovoltaic components. For this, we apply distinct state-of-the-art machine learning techniques (AutoEncoder Long Short-Term Memory (AE-LSTM), Facebook-Prophet, and Isolation Forest) to detect faults/anomalies and evaluate their performance. These models shall identify the PV system's healthy and abnormal actual behaviors. Our results provide clear insights to make an informed decision, especially with experimental trade-offs for such complex solution space.

Time series data are significant and are derived from temporal data, which involve real numbers representing values collected regularly over time. Time series have a great impact on many types of data. However, time series have anomalies. We introduce hybrid algorithm named novel matrix profile (NMP) to solve the all-pairs similarity search problem for time series data. The proposed NMP inherits the features from two state-of-the art algorithms: similarity time-series automatic multivariate prediction (STAMP), and short text online microblogging protocol (STOMP). The proposed algorithm caches the output in an easy-to-access fashion for single- and multidimensional data. The proposed NMP algorithm can be used on large data sets and generates approximate solutions of high quality in a reasonable time. The proposed NMP can also handle several data mining tasks. It is implemented on a Python platform. To determine its effectiveness, it is compared with the state-of-the-art matrix profile algorithms i.e., STAMP and STOMP. The results confirm that the proposed NMP provides higher accuracy than the compared algorithms.

Critical Infrastructures and associated real time Informational systems need some security protection mechanisms that will be able to detect and respond to possible attacks. For this reason, Anomaly Detection Systems (ADS), as part of a Security Information and Event Management (SIEM) system, are needed for constantly monitoring and identifying potential threats inside an Information Technology (IT) System. Typically, ADS collect information from various sources within a CI system using security sensors or agents and correlate those information so as to identify anomaly events. Such sensors though in a CI setting (factories, power plants, remote locations) may be placed in open areas and left unattended thus becoming targets themselves of security attacks. They can be tampering and malicious manipulated so that they provide false data that may lead an ADS or SIEM system to falsely comprehend the CI current security status. In this paper, we describe existing approaches on security monitoring in critical infrastructures and focus on how to collect security sensor - agent information in a secure and trusted way. We then introduce the concept of hardware assisted security sensor information collection that improve the level if trust (by hardware means) and also increase the responsiveness of the sensor. Thus, we propose a Hardware Security Token (HST) that when connected to a CI Host, it acts as a secure anchor for security agent information collection. We describe the HST functionality, its association with a host device, its expected role and its log monitoring mechanism. We also provide information on how security can be established between the Host device and the HST.Then, we introduce and describe the necessary Host components that need to be established in order to guarantee a high security level and correct HST functionality. We, also provide a realization-implementation of the HST overall concept in a FPGA SoC evaluation board and describe how the HST implementation can controlled. Finally, we provide indicative use case scenarios of how the HST can be used in practice to provide a variety of different security services beyond acting as a secure ADS sensor.

Adaptations to climate change rely on understanding the dynamics of plant biomass stocks on the planet. The high levels of deforestation in Cerrado have transformed this biome into the second-largest Brazilian source of carbon emissions. The objective of this study was to develop a method to accurately estimate aboveground and total biomass values among shrublands, savannas, and forests located in the Cerrado biome, using an allometric equation adjusted from canopy height, obtained through optical and laser sensors. The results show similarity between the estimates employed by our method and the data found in the literature review for different phytophysiognomies in the Cerrado biome. Shrubland formations showed higher biomass estimation uncertainties due to the discontinuity of isolated trees and the lower canopy height when compared to more clustered tree canopies in savannas and taller canopies in forests. Aboveground biomass estimates were related to expansion factors, and specific maps were developed for each compartment by root, litter, and necromass. The sum of these compartments is presented in the aboveground and below forest biomass map. This study presents, for the first time, the mapping of total biomass in 10 m pixels of all regions of the Cerrado biome.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.