This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Moose (Alces alces) are generalist herbivores but are important aquatic-terrestrial ecotone specialists. Aquatic macrophytes are a high-quality food source for moose during the summer, however their relative importance to moose diet is difficult to study. We used stable isotope analysis of carbon and nitrogen from moose hooves and forage (terrestrial plants, aquatic macrophytes, and arboreal lichen) to estimate the diet of moose at Isle Royale National Park, Michigan, USA, and to evaluate the isotopic variability along chronologies of serially sampled hooves. We hypothesized that aquatic macrophyte consumption and winter body condition (as measured by bone marrow fat content) would be greater at the eastern end of the island where aquatic habitats were most abundant. We were unable to evaluate spatial differences in aquatic macrophyte consumption, but overall, our mixing model results suggest that between 13% and 27% of summer moose diet was from aquatic sources. Among moose that died during winter, body condition was impaired and hoof δ¹⁵N (measured at the hairline) was higher at the western end of the island, where aquatic habitats are sparse. Although isotope chronologies preserved in hooves could significantly enhance our understanding of ungulate foraging ecology, interpretation of such chronologies is presently limited by our lack of knowledge pertaining to hoof growth rate and seasonal dynamics in relation to age and health. Significant isotope distinction among terrestrial plants, aquatic macrophytes, and arboreal lichens indicate that continued methodological advances in stable isotope ecology will lead to more precise estimates of the contribution of aquatic feeding to moose population dynamics.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

The effect of seven different thawing methods (atmospheric temperature thawing (AT), microwave thawing (MT), microwave magnetic nanoparticles thawing (MMT), microwave vacuum thawing (MVT), far-infrared thawing (FT), far-infrared magnetic nanoparticles thawing (FMT) and far-infrared ultrasonic thawing (FUT)) on water mobility and microstructure of frozen pork was examined. The results showed that the thawing loss, cooking loss, and centrifugal loss of MVT treatment were lower than those of other thawing methods. The results of LF-NMR and NMRI showed that in MVT and FUT treatment, the proportion of bound water and non-flowing water increased, while the proportion of free water decreased. The microstructure was significantly improved by microwave or far-infrared thawing assisted by magnetic nanoparticles, and the frozen pork samples had a more compact and granular microstructure. In summary, MVT and FUT improved the quality of thawed meat and have broad potential applications in thawing meat.

Cryopreservation is a stressful process for sperm as it is associated with an increased production of reactive oxygen species (ROS). Elevated ROS levels, which create an imbalance with antioxidant capacity, may result in membrane lipid peroxidation (LPO), protein damage and DNA fragmentation. This study aimed to determine whether membrane LPO and DNA fragmentation of frozen-thawed horse sperm relies upon the antioxidant activity, including enzymes (superoxide dismutase (SOD), glutathione peroxidase (GPX), catalase (CAT), and paraoxonase type 1 (PON1)); non-enzymatic antioxidant capacity (Trolox equivalent antioxidant capacity (TEAC), plasma ferric reducing antioxidant capacity (FRAP), and cupric reducing antioxidant capacity (CUPRAC)); and the oxidative stress index (OSI), of their seminal plasma (SP). Based on total motility and plasma membrane integrity (SYBR14+/PI−) after thawing, ejaculates were hierarchically (p < 0.001) clustered into two groups of good (GFE) and poor (PFE) freezability. LPO and DNA fragmentation (global DNA breaks) were higher (p < 0.05) in PFE than in GFE, with LPO and DNA fragmentation (global DNA breaks) after thawing showing a positive relationship (p < 0.05) with SP-OSI levels and ROS production. In addition, sperm motility and membrane integrity after thawing were negatively (p < 0.05) correlated with the activity levels of SP antioxidants (PON1 and TEAC). The present results indicate that LPO and DNA fragmentation in frozen-thawed horse sperm vary between ejaculates. These differences could result from variations in the activity of antioxidants (PON1 and TEAC) and the balance between the oxidant and antioxidant components present in the SP.

Participatory landscape conservation is an innovative approach that weaves theory and practice to bridge the gap between theoretical models and practical applications. Intertropical regions as the case of Mexico face challenges to conciliate regional governability, social justice, and nature conservation. The State of Michoacan is one of these regions where the challenges exacerbate since nature conservation is last due to its ongoing territorial disputes. We implemented the participatory landscape conservation approach by creating a complementary form of protected areas with ongoing conflicts, drought conditions, and extreme poverty. We conducted participatory mapping and land cover/use analyses as main methodological tools to reach consensus among stakeholders. We integrated, macro, micro and social scales to provide sound arguments to integrate local, scholar and policy makers perceptions. The outcomes of the participatory mapping analyses were assessed. The present papers provide evidence of the positive outcome of using a Participatory Landscape Conservation to establish a Biosphere Reserve, safeguarding one of the most biologically diverse and delicate ecosystems consisting of seasonally dry tropical forests within a rather disputed region. We discussed the relevance of our findings and compared them to ongoing regional and global trends in the light of other forms of establishing protected areas.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

The sperm heads of frozen/thawed horse spermatozoa were injected into ovulated mouse oocytes where they decondensed and formed paternal pronuclei in which the DNA damage has been evaluated. The motile spermatozoa exhibit none or minor level of DNA damage and the xenogenic zygotes cleave to the two-cell embryonic stage with regular nuclei and no micronuclei (MNs). On the other hand, the immotile spermatozoa exhibit typically high levels of DNA damage and blastomeres in two-cell stage embryos contain multiple MNs. Moreover, extremely high sperm DNA damage prevents even the cleavage to the two-cell stage.Keywords: keyword 1; keyword 2; keyword 3 (List three to ten pertinent keywords specific to the article yet reasonably common within the subject discipline.)

Antioxidants have multiple protective roles in cells and can be used as a supplement to protect cells against cryopreservation-induced detrimental effects, including protecting sperm fertility quality. The antioxidant resveratrol (3,5,4-trihydroxy-trans-stilbene; RSV) has been shown to be a protective supplement for the cryopreservation of animal sperm, including human sperm. In this study, we assessed the effect of RSV supplementation on canine sperm cryopreservation. Semen was collected from four dogs and the effect of different concentrations of RSV (0, 100, 200, and 400 µM) on post-thaw quality of sperm was examined. After thawing, sperm motility was assessed using computer aided sperm analysis, and the structural integrity of the plasma membrane, acrosome, and chromatin were examined, as well as mitochondrial activity and gene expression were assessed. Dog sperm cryopreserved with 200 µM RSV showed significant improvement in motility and viability following thawing compared with that of the control group (p < 0.05). Moreover, RSV-supplemented samples showed significantly higher numbers of sperm with an intact plasma membrane, active mitochondria, and structural integrity of acrosomes and chromatin than that of control samples (p < 0.05). Furthermore, gene expression showed that RSV supplemented samples showed lower expression of pro-apoptotic (BAX) oxidative stress-related (ROMO1) and oxidative induced DNA damage repair (OGG1) whereas higher expression levels of anti‐apoptotic (BCL2) protamine-2 (PRM2), protamine-3 (PRM3) and sperm acrosome‐associated (SPACA3) genes than control. Our results suggest that RSV, at its optimum concentration, can be efficiently used as an alternative antioxidant in the cryopreservation of dog sperm.

Frost heave, which is the volumetric expansion of frozen soil, has great ecological significance, since it creates water storage spaces in soils at the beginning of the growing season in cold temperate forests. To understand the characteristics of frost heave in seasonally frozen soil and the factors that impact its extent, we investigated the frost heave rates of forest soil from different depths and with different soil moisture contents, using both lab-based simulation and in situ measurement in a broadleaved Korean pine forest in the Changbai Mountains (northeastern China). We found that frost heave was mainly affected by soil moisture content, soil type, and gravitational pressure. Frost heave rate increased linearly with soil moisture content, and for each 100% increase in soil moisture content, the frost heave rate increased by 41.6% (loam, upper layer), 17.2% (albic soil, middle layer), and 4.6% (loess, lower layer). Under the same soil moisture content, the frost heave rate of loam was highest, whereas that of loess was lowest, and the frost heave of the uppermost 15 cm, which is the biologically enriched layer, accounted for ~55% of the frost heave. As a result, we determined the empirical relationship between frost heave and freezing depth, which is important for interpreting the effects of frost heave on increases in the storage space of forest soils and for calculating changes in soil porosity.

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

Vector-borne disease (VBD) accounts for more than 17% of the global infectious disease burden, disproportionately affecting developing nations within tropical and subtropical areas. As Aedes aegypti mosquitoes are the principal vector for the transmission of many Public Health pathogens, our study examined their population dynamics within the seasonal context of tropical dry biomes in El Salvador as incidence of VBD in this region has increased in recent years. Species that rely on sexual reproduction must maintain a balanced sex ratio (1:1) to support their population dynamics, however, our phenological analysis of field-collected A. aegypti specimens revealed significant sex ratio variations during dry and wet seasons. Interestingly, we detected a seasonal shift that favored female mosquitoes during the dry season, highlighting the dynamic nature of mosquito populations in highly urbanized environments like El Salvador. By linking sex ratio distortions to anthropogenic factors, our study underscores the importance of comprehensively characterizing the urban ecology of vectors for the development of effective biocontrol strategies. As such, we advocate for more nuanced vector control approaches that consider ecological factors as well as the human behaviors that influence mosquito breeding habitats to effectively combat the rise of VBDs amid global climate changes.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Electrospun nanofiber-supported thin film composite membranes are among the most promising membranes for seawater desalination via forward osmosis. In this study, a high-performance electrospun polyvinylidenefluoride (PVDF) nanofiber-supported TFC membrane was successfully fabricated after molecular layer-by-layer polyelectrolyte deposition. Negatively-charged electrospun polyacrylic acid (PAA) nanofibers were deposited on electrospun PVDF nanofibers to form a support layer consisted of PVDF and PAA nanofibers. This resulted to a more hydrophilic support compared to the plain PVDF nanofiber support. The PVDF-PAA nanofiber support then underwent a layer-by-layer deposition of polyethylenimine (PEI) and PAA to form a polyelectrolyte layer on the nanofiber surface prior to interfacial polymerization, which forms the selective polyamide layer of TFC membranes. The resultant PVDF-LbL TFC membrane exhibited enhanced hydrophilicity and porosity, without sacrificing mechanical strength. As a result, it showed high pure water permeability and low structural parameter values of 4.12 Lm⁻²h⁻¹bar⁻¹ and 221 µm, respectively, significantly better compared to commercial FO membrane. Layer-by-layer deposition of polyelectrolyte is therefore a useful and practical modification method for fabrication of high performance nanofiber-supported TFC membrane.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

A nanostructured electrochemical bi-sensor system for analysis of milks has been developed using the Layer by Layer technique. The non-enzymatic sensor [CHI+IL/CuPcS]2, is a layered material containing a negative film of the anionic sulfonated copper phthalocyanine (CuPcS) acting as electrocatalytic material, and a cationic layer containing a mixture of an ionic liquid (IL) (1-butyl-3-methylimidazolium tetrafluoroborate) that enhances the conductivity and chitosan (CHI) that facilitates the enzyme immobilization. The biosensor ([CHI+IL/CuPcS]2-GAO) results from the immobilization of galactose oxidase on the top of the LbL layers. FTIR, UV-vis and AFM have confirmed the proposed structure and cyclic voltammetry has demonstrated the amplification caused by the combination of materials in the film. Sensors have been combined to form an electronic tongue for milk analysis. Principal Component Analysis has revealed the ability of the sensor system to discriminate between milk samples with different lactose content. Using PLS-1 calibration models, correlations have been found between the voltammetric signals and chemical parameters measured by classical methods. PLS-1 models provide excellent correlations with lactose content. Additional information about other components such as fats, proteins and acidity can also be obtained. The method developed is simple and the short response time permits its use in assaying milk samples on-line.

Fertilized zygotes normally display 2 pronuclei (PN) but abnormal fertilization patterns (0, 1 or >2 PN) are daily observed in IVF labs. Multiple PN zygotes (>2) are generally discarded due to an increased risk of aneuploidy. However, the decision to transfer or not 1PN-derived embryos remains controversial. The aims of our study were to analyze the neonatal outcomes of fresh or frozen-thawed embryos derived from 1PN zygotes, and to evaluate the influence of the fertilization method. Data were retrospectively collected from cycles performed between January 2018 and December 2022. Fresh cycles were analyzed for the comparative fate of 1PN zygotes (n=1234) following conventional in vitro fertilization (cIVF; n=648) or intracytoplasmic sperm injection (ICSI; n=586), as well as the results of the 64 transfers of 1PN derived embryos (pregnancy rate (PR) and neonatal outcomes). This pregnancy follow-up was also applied to 167 transfers of frozen-thawed 1PN derived embryos. In fresh cycles, 46% of the 1PN zygotes in cIVF group gave rise to embryos of sufficient quality to be transferred or frozen (day 3 or 5/6). This rate decreased to 33% in the fresh ICSI cycles. Blastulation rate was also significantly higher in cIVF group (44%) in comparison to ICSI group (20%). The fresh embryo transfers (32 per group) allowed 7 pregnancies in the cIVF group (PR=21.9%) as compared to 4 pregnancies in the ICSI group (PR=12.5%). In the cIVF group, 4 deliveries of healthy newborns were achieved and only one in the ICSI group. In frozen/thawed cycles, 36 pregnancies were obtained out of the 167 transfers. A non-significative difference was observed between embryos derived from cIVF cycles (PR=26%) and ICSI cycles (PR=16%) with respectively 18 and 8 healthy babies born. In conclusion, we observed better outcomes for 1PN zygotes in cIVF cycles in comparison to ICSI cycles. Our center policy to transfer good quality 1PN-derived embryos allowed the birth of 31 healthy babies.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, polymer D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via LBL fabrication method in regulating microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

This paper intends to discuss SSLs, how they work, their advantages and drawbacks. It will end with the author’s thoughts on the efficacy of the system and whether it is a viable solution for the majority of network security problems or if those drawbacks prevent that.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

The present study was conducted to compare embryo survival rate and treatment outcomes including pregnan-cy, miscarriage and live birth rates of IVF and ICSI vitrified-thawed embryo transfers. Authors suggested to compare treatment outcomes [clinical pregnancy, miscarriage, ectopic pregnancy, and live birth rates] after transfer of IVF versus ICSI vitrified-thawed embryos. Cohort retrospective study in the IVF unit at a university af-filiated Medical Center which included 845 frozen thawed embryo transfer cycles of vitrified embryos from treatment cycles between the years 2013-2019. Out of 845 FET cycles of vitrified thawed embryos, 223 clinical pregnancies were achieved [26.4%]. Of these 64 [28.4%] following IVF, 131 [25.6%] after ICSI and 28 [25.9%] in the sibling oocytes group [P =0.631]. Live birth rate did not differ between the three groups: 23.6%, 22.3% and 21.5% for groups IVF, ICSI and IVF+ICSI, respectively [p=0.899]. Sub analysis by age below 35 and above 35 years old revealed no statistical difference between IVF and ICSI cycles in terms of clinical pregnancy, miscarriage, ectopic pregnancy, and live birth rates between the groups. The present study suggests that the technique of insemina-tion has no adverse effect related to vitrification.

Ring necked-pheasant (Phasianus colchicus) is bird of order Galliformes. Ring necked-pheasant is also known as gallinaceous bird and game bird. It looks like chicken bird. It is national bird of South Dakota. It is mostly found in wild areas but in Pakistan it exists as Domestic bird. It has high proteins and low fat in its meat. The present study was conducted to check the effect of ascorbic acid on sperm Motility, sperm cytoplasmic membrane integrity, sperm livability and acrosome integrity of Ring-necked pheasant at different concentrations of ascorbic acid (0mM, 1mM, 2mM, 3mM and 4mM) were used. Semen was collected by abdominal massage technique. Motility of sperm was greater than 70%.Then it was processed further. The cryopreservation of semen was checked at various stages like Post Dilution, Post Cooling, Post Equilibration and Post Thawing. Semen was cooled from post-dilution stage (37⁰ C) to post-cooling (20⁰C).Then it further cooled gradually to get post-equilibration stage (4⁰ C) within 24 hours. After that 10% glycerol was added to the sample. Then it was transferred to liquid nitrogen (LN₂) cylinder for 24 hours. After thawing stage sample was removed from LN₂ cylinders and placed in water bath for 4 hours to achieve post-thawing. Then performed sperm quality assays at each stage of cryopreservation. Sperm motility was assessed by Neubauer Chamber Hemocytometer. Plasma Membrane Integrity was checked by using Hypo Osmotic Swelling Test with the help to 2% Eosin. Sperm livability was assessed by Lake’s glutamate solution and sperm Acrosome Integrity was checked by dual staining technique by using Formal citrate solution and Giemsa stain. The better results were seen at 3mM treatment of ascorbic acid. Sperm motility percentage was significantly different (P < 0.05) on 3mM treatment on all the stages of cryopreservation rather than other treatments. Plasma membrane integrity assay also showed good results at same concentration (P < 0.05) on all the stages of cryopreservation rather than other treatments. At the sperm livability stage 3mM treatment showed significantly difference (P < 0.05) on all the stages of cryopreservation rather than other treatments. The sperm acrosome integrity showed highest percentage on 3mM treatment (P < 0.05) on all stages of cryopreservation rather than other treatments. Effect of ascorbic acid on all the quality parameters (sperm motility, plasma membrane integrity, livability and acrosome integrity) was showed significant difference (P < 0.05) at 3mM treatment of ascorbic acid as compare to control as well as remaining treatments. It was seen that by increasing the concentration of ascorbic acid from 3mM concentration to onward it shows negative results on its cryopreservation. Now this cryopreserved semen can be transfer from one place to another place to obtain good varieties as well as better genetic characteristics of this species.

The present Feature Paper highlights the application of bacterial surface (S-) layer proteins as versatile components for the fabrication of biosensors. One technologically relevant feature of S‑layer proteins is their ability to self-assemble on many surfaces and interfaces to form a crystalline 2D protein lattice. The S-layer lattice on the surface of a biosensor becomes part of the interface architecture, linking the bioreceptor to the transducer interface, which may cause signal amplification. The S-layer lattice as ultrathin, highly porous structure with functional groups in a well-defined special distribution and orientation and an overall anti-fouling characteristics can significantly raise the limit in terms of variety and ease of bioreceptor immobilization, compactness of bioreceptor molecule arrangement, sensitivity, specificity, and detection limit for many types of biosensors. The present paper discusses and summarizes examples for the successful implementation of S-layer lattices on biosensor surfaces in order to give a comprehensive overview on the application potential of these bioinspired S-layer protein-based biosensors.

Here, we investigate the actuation dynamics of a micro device with different intervening liquids between the actuating components under the influence of Casimir and dissipative hydrodynamic forces. This is enabled via phase space portraits, which demonstrate that by increasing the dielectric response of the intervening layer the device may not come into stiction due to the decreasing in magnitude Casmir force. Moreover, it is feasible to expand area of motion using intervening liquids with lower dynamic viscosity or increasing the slip length of the intervening fluid. Finally, under the influence of an external driven force, which is the realistic case for possible applications, the system can reach stable oscillation at larger separations with an amplitude higher for the liquid that lead to lower Casimir and hydrodynamic forces.

Montes de María is the best-preserved tropical dry forest fragment in the Colombian Caribbean, making it an ideal location for studying the impacts of human disturbance on local ecosystems. This study analyzed the ecological structure of diurnal butterflies in both forested and disturbed areas using 16 circular plots to identify relationships between alpha and beta diversity, and the geographic distance between disturbed areas and native forests, using a range of metrics, including range-abundance and rarefaction curves, nonlinear models, and the Bray–Curtis dissimilarity index. Results revealed three distinct species assemblages associated with forest, intermediate disturbed areas (IDA), and disturbed areas (DA). Nonlinear models show that IDA are more diverse than forest and DA. However, forests have more beta diversity among plots than IDA and DA. Indicator species for each butterfly assemblage were also identified. Thus, although new butterfly species assemblages emerge from a new human land-scape, it is clear that species that only occur within dry forest fragments are lost when forest fragments disappear. Overall, these findings have important implications for conservation efforts and understanding how human disturbance affects biodiversity in tropical ecosystems.

Background: It is unknown whether prolonged artificial hormonal environment during early fetal development affects the birthweight of singletons born after frozen-thawed embryo transfer (FET). Methods: A retrospective observational study included singleton births>22 weeks of gestation obtained after FET between 2013-2019 after endometrial preparation with ovulatory cycle (OC) or artificial cycle (AC). Our primary objective was to compare birthweight of singletons after FET between endometrial preparation by OC or AC. Secondary objectives included prolonged pregnancies, high birthweight, low birthweight, SGA and LGA rates. Multivariate analyses were performed considering potential confounding factors. Results: Among 198 singleton live births after FET, 112 were obtained with OC and 86 with AC. Prolonged pregnancies rate was higher in AC (25.6% vs. 7.1%, respectively, p=0.001). Mean birthweight was higher (+219g) in AC (3386g vs. 3167g, p=0.01; adjusted-p=0.052), as well as the rate of babies exceeding 4000g (16.3% vs. 2.7%, p=0.03, adjusted-p=0.015). The rate of babies <2500g was lower in AC (3.5% vs. 11.6%, respectively, p=0.050, adjusted-p=0.049). Conclusions: Since OC does not strain the chances of pregnancy and in the incomplete knowledge of the consequences of neonatal overweight on the future health of children, OC preparation could be advocated as first-line endometrial preparation in FET.

OSI model used to be common network model for years. In the case of ad hoc networks with dynamic topology and difficult radio communications conditions, gradual departure is happening from the classical kind of OSI network model with a clear delineation of layers (physical, channel, network, transport, application) to the cross-layer approach. The layers of the network model in ad hoc networks strongly influence each other. Thus, the cross-layer approach can improve the performance of an ad hoc network by jointly developing protocols using interaction and collaborative optimisation of multiple layers. The existing cross-layer methods classification is too complicated, because it’s based on the whole manifold of network model layers combinations, regardless their importance. In this work, we review ad hoc networks cross-layer methods, propose the new useful classification of cross-layer methods, and show future research directions in ad hoc networks cross-layer methods development. The proposed classification can help to simplify the goal-oriented cross-layer protocol development.

A 9,10-phenanthrenequinone (PQ) was electrochemically polymerized on a graphite rod electrode using potential cycling. The electrode modified by poly-9,10-phenanthrenequinone (poly-PQ) was studied by means of cyclic voltammetry, electrochemical impedance spectroscopy, atomic force microscopy and scanning electron microscopy. The poly-PQ shows variations in growth pattern depending on the number of potential cycles for the initiation of polymerization. Formed poly-PQ layer demonstrates good electric conductivity, great electrochemical capacitance and unique oxidation/reduction properties, which are suitable for broad technological applications, including applicability in biosensors, supercapacitors, and in some other electrochemical systems.

Carburizing of stainless steels at low temperatures (below 500°C) develops a high content carbon layer, known for its high hardness. X-ray Diffraction investigation indicates that carburization treatment does not impact the structure of substrate; however, introduced carbon causes expansion in the carburized layer through the increase in d-spacing. Characterization of carbon concentration and hardness profiles indicate that carbon content gradually decreases while moving further into the substrate; and the origin of the increased hardness of the expanded layer arises from the super-saturated carbon content, following the solid solution strengthening theory. An area that is not well understood is in regard to the carburized layer’s relation to the substrate and the significance in their differences. Using two grades of stainless steel, AISI 316L and PH 17-4, it was observed that the carburized layer is not a separate layer, but a higher carbon content version of the substrate,

The design and engineering of antibacterial materials is key for preventing bacterial adherence and proliferation in biomedical and house-hold instruments. Silver nanoparticles (AgNPs) and chitosan (CHI) are broad-spectrum antibacterial materials with different properties, whose combined application is currently under optimization. This study proposes the formation of antibacterial films with AgNPs embedded in carboxymethylcellulose/chitosan multilayers by the layer-by-layer (LbL) method. The films were deposited onto nanoporous silicon (nPSi), an ideal platform for bioengineering applications, due to its biocompatibility, biodegradability, and bioresorbability. We focus on two alternative multilayer deposition processes: cyclic dip coating (CDC) and cyclic spin coating (CSC). The physicochemical properties of the films were the subject of microscopic, microstructural and surface-interface analyses. The antibacterial activity of each film was investigated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria strains as model microorganisms. According to the findings, CDC technique produced multilayer films with higher antibacterial activity for both bacteria compared to the CSC method. Bacteria adhesion inhibition was observed from only 3 cycles. The developed AgNPs-multilayer composite film offers advantageous antibacterial properties for biomedical applications.

To achieve an acceptable level of security on the web, the Completely Automatic Public Turing test to tell Computer and Human Apart (CAPTCHA) was introduced as a tool to prevent bots from doing destructive actions such as downloading or signing up. Mobile devices have small screens, and therefore, using the common CAPTCHA methods (e.g. text CAPTCHAs) in these devices raises usability issues. To introduce a reliable, secure, and usable CAPTCHA that is suitable for mobile devices, this paper introduces a hand gesture recognition CAPTCHA based on applying Genetic Algorithm (GA) principles on Multi-Layer Perceptron (MLP). The proposed method improves the performance of MLP-based hand gesture recognition. It has been trained and evaluated on 2201 videos of the IPN Hand dataset, and MSE and RMSE benchmarks report the index values of 0.0018 and 0.0424, respectively. Comparison with the related works shows a minimum of 1.79% fewer errors, and experiments produced a sensitivity of 93.42% and accuracy of 92.27% – 10.25% and 6.65% improvement compared to the MLP implementation.

Using co-precipitation to synthesize (CeO2)0.95(Y2O3)0.05 (YDC) and solid reaction method to synthesize (CeO2)0.75(ZrO2)0.25 (ZDC), and the characterization for both crystal structure and micro-structure of the two materials was conducted with X-ray diffraction (XRD) and scanning electron microscope (SEM) methods. Prepare the YDC and ZDC based limited current O2 sensor by employing platinum pasting bonding method. Sensing characteristics of the sensor were obtained at different conditions and study on the impact of temperature, O2 concentration as well as water vapor pressure on the sensing characteristics had been conducted. XRD results show that the phase structure of both YDC and ZDC is cubic phase. SEM results show that both YDC and ZDC layers are dense layers, which are then qualified to be the composition materials of the sensor. This limited current O2 sensor shows good sensing performance and conforms to the Knudsen model. Log(IL•T) depends linearly on 1000/T with R2 of 0.9904, IL depends linearly on x(O2) with R2 of 0.9726 and sensing characteristics are not affected by p(H2O).

Fires are a significant threat to people, property, and environment. One of the requirements for the buildings during fires is ensuring the safe evacuation of persons. The evacuation assessment has usually been based on a comparison of the Required Safe Egress Time (RSET) and the Available Safe Egress Time (ASET). One of the important factors influencing the safe evacuation of persons is smoke, which is an important accompanying phenomenon in the burning of polymers. The smoke layer interface is one basic barrier for effective evacuation. The current calculation technique for assessing the smoke layer interface in the Czech Republic is unsatisfactory. For this reason, a calculation technique CSN has been derived, which has been compared with the selected simple calculation techniques, the zone fire model Consolidated Model of Fire and Smoke Transport (CFAST) and the field type model Fire Dynamics Simulator (FDS). The CSN technique was also compared with a real large-scale experiment. The data were also subjected to statistical evaluation using the root mean square error method (RMSE). The deviations between the NFPA, ISO and CSN calculation techniques, the CFAST and FDS fire models and the implemented experiment ranged from 0.05 to 2.41. The established deviations indicate that the calculation technique CSN will be practically usable.

In recent years, antibacterial coatings have become a significant approach in the global fight against bacterial pathogens. Developments in materials science, chemistry and biochemistry have led to a plethora of materials and chemical compounds that have potential for creating antibacterial coatings. Nonetheless, there has been insufficient consideration given to the analysis of the techniques and technologies used to apply these coatings. Among the various inorganic coating techniques, Atomic Layer Deposition (ALD) is noteworthy. It enables the successful synthesis of high-purity inorganic nanocoatings on surfaces of complex shape and topography, while also providing precise control over their thickness and composition. ALD has various industrial applications, but its practical application in medicine is still limited. In recent years, a substantial number of papers have been published on the suggested implementation of thin films and coatings produced through ALD in medicine, notably those with antibacterial properties. The aim of this paper is to carefully evaluate and analyse the relevant literature on this subject. Simple oxide coatings, including TiO2, ZnO, Fe2O3, MgO, and ZrO2, were examined, as well as coatings containing metal nanoparticles such as Ag, Cu, Pt, and Au, and mixed systems such as TiO2-ZnO, TiO2-ZrO2, ZnO-Al2O3, TiO2-Ag, and ZnO-Ag. Through comparative analysis, we have been able to draw conclusions on the effectiveness of various antibacterial coatings of different compositions, including key characteristics such as thickness, morphology, and crystal structure. ALD has been analysed in its use for developing antibacterial coatings for various applications. Furthermore, assumptions regarding the most promising development areas have been presented.

A solution for the Prandtl-Blasius equation is essential to all kinds of boundary layer problems. This paper revisits this classic problem and presents a general Maple code as its numerical solution. The solutions were obtained from the Maple code, using the Runge-Kutta method. The study also considers convergence radius expanding and an approximate analytic solution is proposed by curve fitting. Similarly, the study resolves some boundary layer related problems and provide relevant Maple codes for these.

Recently Li et al (2019 Nature 572 624) discovered a new type of oxide superconductor Nd_0.8Sr_0.2NiO₂ with T_c = 14 K. To classify superconductivity in this infinite-layer nickelate experimental upper critical field, B_c2(T), and the self-field critical current densities, J_c(sf,T), reported by Li et al (2019 Nature 572 624), are analysed in assumption of s-, d-, and p-wave pairing symmetries and single- and multiple-band superconductivity. Based on deduced the ground-state superconducting energy gap, Δ(0), the London penetration depth, λ(0), the relative jump in electronic specific heat at T_c, ΔC/C, and the ratio of 2Δ(0)/k_BT_c, we conclude that Nd_0.8Sr_0.2NiO₂ is type-II high-κ weak-coupled single-band s-wave superconductor.

In a thin-volume photobioreactor where a concentrated suspension of microalgae is circulated throughout the established spatial irradiance gradient, microalgal cells experience a time-variable irradiance. Deploying this feature is the most convenient way of obtaining the so-called “flashing light” effect, improving biomass production in high irradiance. This work investigates the light flashing features of sloping wavy photobioreactors, a recently proposed type, by introducing and validating a Computational Fluid Dynamics model. Two characteristic flow zones (straight top-bottom stream and local recirculation stream), both effective toward light flashing, have been found and characterised: a recirculation-induced frequency of 3.7 Hz and straight flow-induced frequency of 5.6 Hz were estimated. If the channel slope is increased, the recirculation area becomes less stable while the recirculation frequency is nearly constant with flow rate. The validated CFD model is a mighty tool that could be reliably used to further increase the flashing frequency by optimising the design, the dimensions, the installation and the operational parameters of the sloping wavy photobioreactor.

Mixing layer height (MLH) is a crucial parameter for air quality modelling that is still not routinely measured. Common methods for MLH determination use atmospheric profiles recorded by radiosonde but they suffer from course temporal resolution since balloon launching is only twice a day. Recently cheap ceilometers are gaining popularity in the retrieval of MLH diurnal evolution based on aerosol profiles. This study presents a comparison of a proprietary (Jenoptik) and a free available (STRAT) algorithms to retrieve MLH diurnal cycle. The comparison is accomplished in summer season over urban area and radiosonde data is used to estimate MLHs according to parcel, lapse rate, and Richardson methods (the last algorithm is used as a reference in the study) in addition. It was found that STRAT and Jenoptik give lower MLH than radiosonde with an underestimation of about 150m and 650m respectively. Additionally, STRAT showed reasonable performance in tracking of MLH diurnal evolution. Daily MLH maximum of about 2000m was found in the late afternoon (18-19 LT). In contrast, Jenoptik algorithm showed more weaknesses, mainly attributed to its real-time operation and independent processing of a single profile. At night and during morning transition period, both lidar-based methods showed difficulties as MLH was often in the ceilometer’s incomplete overlapping zone so residual or advected aerosol layers aloft were misleadingly reported as mixing layer (ML).

: In today’s rapidly expanding era of the Internet of Things (IoT) and the Industrial Internet of Things (IIoT), the emphasis on robust data security and insightful data interpreta- tion is more pronounced than ever. This research introduces a comprehensive approach to both data protection and predictive analytics, leveraging the diverse dataset TON IoT.csv, sourced from a myriad of IoT and IIoT environments. For data security, a dual-encryption technique incorporating both AES and RSA algorithms is established. Its efficacy is evidenced by a perfect match between the original and decrypted datasets, underscoring the integrity of our encryption process. Concurrently, the study ventures into predictive modeling using a modified Snake Optimization Algorithm (SOA) to streamline hyperparameter selection. This subsequently aids in the development and fine-tuning of an LSTM network, which exhibits remarkable predictive accuracy. Additionally, the paper provides an in-depth examination of various encryption methodologies like elliptic curve cryptography (ECC), Lightweight Cryptography for Cloud computing, and homomorphic encryption, while also emphasizing the nuances of encryption in cloud setups, particularly contrasting server-side with client-side encryption and efficient key management. The insights presented serve as a cornerstone for ensuing research, promising a bright future for advancements in IoT and IIoT data protection and analysis

The studies of laminar unsteady boundary layer flows is crucial for understanding laminar-turbulence transition and origins of turbulence. However, the task of finding its solutions poses a significant challenge. In this paper, we propose a novel approach by introducing a similar transformation to convert the 2D unsteady laminar boundary layer equations into a single partial differential equation. By applying this transformation, we are able to obtain the "exact" similarity solutions for the 2D unsteady laminar boundary layer equations, specifically for the case of flat plate boundary flow. Notably, this is the first time that such an exact solution has been obtained. Application of this exact solution is being used to solve Stokes' first problem in 2D boundary layer. Perspectives on the transition fron Rayleigh solution to Blasius solution is provided.

This study introduces an alternative to the existing methods for measuring ocean currents based on a recently developed technology. The SailBuoy is an unmanned surface vehicle powered by wind and solar panels that can navigate autonomously to predefined way-points and record velocity profiles using an integrated downward-looking Acoustic Doppler Profiler (ADCP). Data, collected on two validation campaigns, shows a satisfactory correlation between the SailBuoy current records and traditional observation techniques such as bottom mounted and moored current profilers and moored single-point current meter. While the highest correlations were found in tidal signals, strong current, and calm weather conditions, low current speeds and varying high wave and wind conditions reduced correlation considerably. Filtering out some events with high sea surface roughness associated with high wind and wave conditions may increase the SailBuoy ADCP listening quality and lead to better correlations. Not yet resolved is a systematic offset between the measurements obtained by the SailBuoy and the reference instruments of ± 0.03 m/s. Possible reasons are discussed to be the differences between instruments (various products) as well as changes in background noise levels due to environmental conditions.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

In recent decades, considerable attention has been focused on the design and development of surfaces with defined or tunable properties for a wide range of applications and fields. To this end, self-assembled monolayers (SAMs) of organic compounds offer a unique and straightforward route of modifying and engineering the surface properties of any substrate. Thus, alkane-based self-assembled monolayers constitute one of the most extensively studied organic thin-film nanomaterials, which have found wide application in antifouling surfaces, control of wettability or cell adhesion, sensors, optical devices, corrosion protection, organic electronics, among many other applications. Some of which have led technological transfer to industry. Nevertheless, recently, aromatic-based SAMs have gained in importance as functional components, particularly in molecular electronics, bioelectronics, sensors, etc., due to their intrinsic electrical conductivity and optical properties, opening up new perspectives in these fields. However, some key issues affecting device performances still need to be lifted off to ensure their full use and access to novel functionalities such as memories, sensors, or active layers in optoelectronic devices. In this context, we will present herein recent advances of p-conjugated systems-based self-assembled monolayers (e.g., push-pull chromophores) as active layer and their applications.

The wheat aleurone layer is, according to millers, the main bran fraction. It is a source of nutritionally valuable compounds, such as dietary fibres, proteins, minerals and vitamins, that may exhibit health benefits. Despite these advantages, the aleurone layer is scarce on the market, probably due to issues related to its extraction. Many processes exist with some patents, but a choice must be made between the quality and quantity of the resulting product. Nonetheless, its potential has been studied mainly in bread and pasta. While the nutritional benefits of aleurone-rich flour addition to bread agree, opposite results have been obtained concerning its effects on end-product characteristics (namely loaf volume and sensory characteristics), thus ensuing different acceptability responses from consumers. However, the observed negative effects of aleurone-rich flour on bread dough could be reduced by subjecting it to pre- or post-extracting treatments meant to either reduce the particle size of the aleurone’s fibres or to change the conformation of its components.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

Active flow control of canonical laminar separation bubbles by steady and harmonic vortex generator jets (VGJs) was investigated using direct numerical simulations. Both control strategies were found to be effective in controlling the laminar boundary-layer separation. However, the present results indicate that using the same blowing amplitude, harmonic VGJs were more effective and efficient in reducing the separated region than the steady VGJs considering the fact that the harmonic VGJs use less momentum than the steady case. For steady VGJs, longitudinal structures formed immediately downstream of injection location led to formation of hairpin-type vortices causing an earlier transition to turbulence. Symmetric hairpin vortices were shown to develop downstream of the forcing location for the harmonic VGJs as well. However, the increased control effectiveness for harmonic VGJs flow control strategy is attributed to the fact that shear-layer instability mechanism was exploited. As a result, disturbances introduced by VGJs were strongly amplified leading to development of large-scale coherent structures, which are very effective in increasing the momentum exchange, thus, limiting the separated region.

The research field of two dimensional (2D) materials strongly relies on optical microscopy characterization tools to identify atomically thin materials and to determine their number of layers. Moreover, optical microscopy-based techniques also opened the door to study the optical properties of these nanomaterials. We present a comprehensive study of the differential reflectance spectra of 2D semiconducting transition metal dichalcogenides (TMDCs), MoS₂, MoSe₂, WS₂ and WSe₂, with thickness ranging from one layer up to six layers. We analyze the thickness-dependent energy of the different excitonic features, indicating the change in the band structure of the different TMDC materials with the number of layers. Our work provides a route to employ differential reflectance spectroscopy for determining the number of layers of MoS₂, MoSe₂, WS₂ and WSe₂.

Passive balancing is a traditional choice for lithium-ion battery packs although it is regarded as highly inefficient. One opportunity to improve traditional balancing in sub-medium size battery packs is to combine two balancing methods: passive and active. Statistical analysis have been performed to rationalize battery pack division in smaller packs and use of higher level selective charging method to decrease losses of passive balancing. An experimental balancing prototype have been designed and tested for efficiency. Results indicate energy performance degradation if cells of the pack are with low capacity variation. Proposed balancing approach could improve performance under high cell mismatch conditions.

The newly developed friction-interlocking armor unit, called ‘Double cube’ (DC), has been designed to improve the performance of the concrete armor unit used in river/marine structures against currents/waves actions. DC unit, is an octagonal-shaped block, made up of two parts: an upper cube set on a lower base that is either square or octagonal in shape. The innovative design aims to provide a good performance in terms of stability, high tolerance placement with various contact points and ease of placement. DC’s shape and placement enhance the stability by bringing the center of gravity closer to the underlayer and providing a large contact surfaces with surrounding blocks that reduce the chance of extraction and limit movements (rocking, lifting) via "keystone" effect. The characteristics of this new unit provides a relatively high hydraulic stability number for the armor layer (NS=2.9), a favorable hydraulic performance due to energy dissipation from turbulence and aeration, as well as a high roughness coefficient (γf≈0.46) helping to reduce the overtopping.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

The aim of this paper is to present a comprehensive overview of the main aims and scopes in screening of botanicals, a task which thin-layer chromatography (TLC) is on an everyday basis confronted with and engaged in. Stunning omnipresence of this modest analytical technique (both in its standard format (TLC) and the high-performance one (HPTLC), either hyphenated or not) for many analysts might at a first glance appear chaotic and random, with an auxiliary rather than leading role in research, and not capable of issuing meaningful final statements. Based on these reflections, our purpose is not to present a general review paper on TLC in screening of botanicals, but a blueprint rather (illustrated with a selection of practical examples), which highlights a sovereign and important role of TLC in accomplishing the following analytical tasks: (i) solving puzzles related to chemotaxonomy of plants, (ii) screening a wide spectrum of biological properties of plants, (iii) providing quality control of herbal medicines and alimentary and cosmetic products of biological origin, and (iv) tracing psychoactive plants under forensic surveillance.

In this paper, we propose a lightweight physical layer aided authentication and key agreement (PL-AKA) protocol in the internet of things (IoT). Conventional evolved packet system AKA (EPS-AKA) used in long-term evolution (LTE) systems may suffer from congestions in core networks by the large signaling overhead as the number of IoT devices increases. Thus, in order to alleviate the overhead, we consider a cross-layer authentication by integrating physical layer approaches to cryptography-based schemes. To demonstrate the feasibility of the PL-AKA, universal software radio peripheral (USRP) based tests are conducted as well as numerical simulations. The proposed scheme shows a significant reduction in signaling overhead compared to the conventional EPS-AKA in both simulation and experiment. Therefore, the proposed lightweight PL-AKA has the potential for practical and efficient implementation of large-scale IoT networks.

Few-layer graphene oxide (GO) has shown none or very weak cytotoxicity and anti-proliferative effects in a wide range of cell lines such as glyoma cells and human skin HaCaT cells, in concentrations up to 100 µg/mL However, multi-layer GO has been hardly explored in the biomedical field. Thus, multi-layer GO was examined here in human keratinocyte HaCaT cells treated with different concentrations ranging from 0.01 to 150 µg/mL during different periods of times (3, 12 and 24 hours). The results of this study showed a time-concentration dependence with two non-cytotoxic concentrations (0.01 and 0.05 µg/mL) and a median effective concentration value of 4.087 µg/mL at 24 hours of GO exposure. Contrary to what has been reported for few-layer GO, cell proliferation of the HaCaT cells in contact with the multi-layer GO at 0.01 μg/mL showed identical proliferative activity compared to an epidermal growth factor (1.6-fold greater than the control group) after 96 hours. The effects of the multi-layer GO on the expression of 13 genes (SOD1, CAT, MMP1, TGFB1, GPX1, FN1, HAS2, LAMB1, LUM, CDH1, COL4A1, FBN and VCAN) at the non-cytotoxic concentrations of GO in the HaCaT cells were analyzed after 24 hours. Thus, the lowest non-cytotoxic GO concentration was able to up-regulate the CAT, TGFB1, FN1 and CDH1 genes, which confirms the great potential of multi-layer GO in the biomedical field.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

A novel high-voltage powerline inspection system is investigated, which consists of the cooperated ground vehicle and drone. The ground vehicle acts as a mobile platform that can launch and recycle the drone, while the drone can fly over the powerline for inspection within limited endurance. This inspection system enables the drone to inspect powerline networks in a very large area. Both vehicle’ route in the road network and drone’s routes along the powerline network have to be optimized for improving the inspection efficiency, which generates a new two-layer point-arc routing problem. Two constructive heuristics are designed based on “Cluster First, Rank Second” and “Rank First, Split Second”. Then local search strategies are developed to further improve the quality of the solution. To test the performance of the proposed algorithms, practical cases with different-scale are designed based on the road network and powerline network of Ji’an, China. Sensitivity analysis on the parameters related with the drone’s inspection speed and battery capacity is conducted. Computational results indicate that technical improvement on the inspection sensor is more important for the cooperated ground vehicle and drone system.

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

The paper proves the existence of a family of axisymmetric equilibrium figures as solutions of a stationary problem with unknown boundaries for the Navier–Stokes equations corresponding to the slow rotation of a viscous compressible two-layer liquid mass about some axis. It is assumed that the liquids are barotropic, capillary and have different viscosities, the internal fluid being bounded by a closed surface. This interface does not intersect with the external boundary of the cloud. The proof is based on implicit function theorem and carried out in the Hölder spaces.

The work presented in this paper represents a preliminary study on the performance of the new Silicon tracker layer, the Layer 0 (L0), that will be installed on top of the Alpha Magnetic Spectrometer (AMS-02), at the end of 2024. AMS-02 is a cosmic rays (CR) detector that has been operating on the International Space Stations (ISS) since May 2011. Thanks to its 9-layer Silicon tracker, this apparatus can perform high energy CR measurements with an unprecedented level of statistics and precision. However, high Z (Z $\ge 15$) CR nuclei statistic is strongly affected by fragmentation along the detector: with the installation of the new Silicon layer will be possible to achieve new unique high energy (TeV region) measures for those nuclei along with increased statistics for all nuclei up to Zinc. To achieve this, a Silicon ladder prototype, that will be part of the final Silicon layer, has been exposed to an ions test beam at the super-proton-synchrotron (SPS) of the CERN to characterize its charge resolution and the readout electronics. Preliminary results have shown a charge resolution of 10 $\%$ for nuclei up to Z=7.

The design of water Vessel fender system can minimize impact energy, which could result in severe vessel or offshore structure damage during collision. In order to protect Offshore structures and vessels from damage after impact, a Fender design approach is proposed which uses Soft materials like rubber, sand, inflated rubber tube, etc. to reduce damage on impacted vessels as well as offshore structures like wind turbines, bridges, oil drilling platforms in water etc. The fender is designed in such a way that it can handle vessels made of different material, sizes, and weights.The proposed solution is a fender consisting of a number of layers of soft sandwich materials, each layer getting softer as it moves away from the structure i.e. Hard-Soft fender design which can absorb impact energy upon collision. To handle lighter vessels made of soft or brittle materials, the outer layer is made of inflatable or Very soft foam rubber; however, the inner layer covering the offshore structure is made of hard material to handle heavy vessels made of hard material such as steel. Furthermore, the use of sand as a natural fender along waterways such as narrow channels is also proposed to reduce the cost of fender installation and catastrophic vessel impact damage on rocky ground since it produces less deformation just like rubber fender as demonstrated in the simulation. Finite Element Analysis using ANSYS software, Explicit Dynamic Autodyn, was performed. The results showed a considerable decrease in the total deformation and internal energy of the vessel and fended structure when collision occurs. Furthermore, the result showed that Hard-Soft fender layer performs much better than Soft-Hard-Soft followed by Soft-Hard Fender layer design.

Strained layer superlattice (SLS) material system is being considered for large format, small-pitch and low-cost focal plane arrays for different applications. To address difficulties associated to focal plane arrays fabrication arising from mesa-isolation etching or complex surface treatment/ passivation process, planar structures have been considered. In this work, the recent progress on planar SLS photodetector using ion-implantation for device isolation is presented. The devices are presented here are nBn and pBn heterostructure InAs/InAsSb SLS photodetector, where Zn and Si were chosen as the ion implants, respectively. The electrical and optical performance of the devices were compared along with comparison with mesa-etched device, to give deeper view of the device performance.

We investigate the flow structure and dynamics of moderate-Rayleigh-number ($Ra$) thermal convection in a two-dimensional inclined porous layer. Direct numerical simulations (DNS) confirm the emergence of $\mathit{O}(1)$ aspect-ratio large-scale convective rolls, with one `natural' roll rotating in the counterclockwise direction and one `antinatural' roll rotating in the clockwise direction. As the inclination angle $\phi$ is increased, the background mean shear flow intensifies the natural-roll motion, while suppressing the antinatural-roll motion. Moreover, our DNS reveal---for the first time in single-species porous medium convection---the existence of \emph{spatially-localized} convective states at large $\phi$, which we suggest are enabled by subcritical instability of the base state at sufficiently large inclination angles. To better understand the physics of inclined porous medium convection at different $\phi$, we numerically compute steady convective solutions using Newton iteration and then perform secondary stability analysis of these nonlinear states using Floquet theory. Our analysis indicates that the inclination of the porous layer stabilizes the boundary layers of the natural roll, but intensifies the boundary-layer instability of the antinatural roll. These results facilitate physical understanding of the large-scale cellular flows observed in the DNS at different values of $\phi$.

The administration of regional neuraxial analgesia for pain relief during labor is widely recognized as a safe and effective method involving medication delivery into the epidural or subarachnoid space in the lower back. This study proposes an innovative semantic image segmentation methodology emphasizing enhanced interpretability using convolutional Random Fourier Features and layer-wise weighted class-activation maps tailored explicitly for foot segmentation in regional analgesia monitoring. Namely, our contribution is twofold: i) a novel Random Fourier Features layer is introduced to deal with image data to enhance three well-known architectures (FCN, UNet, and ResUNet); ii) three novel quantitive measures are presented to evaluate the interpretability of a given deep learning model devoted to segmentation tasks. Our approach is rigorously evaluated on a demanding dataset of foot thermal images from pregnant women who received epidural anesthesia. Its small size and considerable variability characterize the dataset. Our validation results demonstrate that the proposed methodology not only achieves competitive foot segmentation performance but also significantly enhances the explainability of the process, rendering it well-suited for applications such as epidural insertion during labor.

Nowadays industrial dryers are used instead of traditional methods for drying. In designing dryers suitable for controlling the process of drying and reaching a high quality product, it is necessary to predict the instantaneous moisture loss during drying. For this purpose, ten mathematical-experimental models with a neural network model based on the kinetic data of pistachio drying are studied. The data obtained from the cabinet dryer will be evaluated at four temperatures of inlet air and different air velocities. The pistachio seeds will be placed in a thin layer on an aluminum sheet on a drying tray and weighed by a scale attached to the computer at different times. In the neural network, data are divided into three parts: educational (60%), validation (20%) and test (20%). Finally, the best mathematical-experimental model using genetic algorithm and the best neural network structure for predicting instantaneous moisture are selected based on the least squared error and the highest correlation coefficient.

Titanium dioxide (TiO2) and aluminum oxide (Al2O3) coatings have been investigated in a wide range of bio-applications due to their biodegradation and biocompatibility properties, that are key parameters for their use in the food packaging and biomedical devices fields. The present study evaluates and compares the electrochemical behavior of the non-coated, commercial resin-coated, TiO2-coated and Al2O3-coated aluminum in commercial beer electrolyte. For this, TiO2 and Al2O3 thin films were deposited on aluminum (Al) substrates using atomic layer deposition (ALD). The evaluation of the corrosion barrier layer properties was performed by linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). In addition, profilometry, grazing incidence X-ray diffractometry (GIXRD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) analyses were performed to investigate the physical and chemical properties of the pristine and / or corroded samples. TiO2 and Al2O3 films presented an amorphous structure, a morphology that follows Al substrate surface, and a thickness of around 100 nm. Analysis of LSV data showed that ALD coatings promoted a considerable increase in corrosion barrier efficiency being 86.3% for TiO2-coated Al and 80% for Al2O3-coated Al in comparison with 7.1% of commercial resin-coated Al. This is mainly due to the lower electrochemical porosity, 11.4% for TiO2-coated Al and 20.4% for Al2O3-coated Al in comparison with 96% of the resin-coated Al, i.e. an increase of up to twofold in the protection of Al when coated with TiO2 compared to Al2O3 coated. The EIS results allow us to complement the discussions about the reduced corrosion barrier efficiency of the Al2O3 film for beer electrolyte once SEM and FT-IR analyzes did not show drastic changes in both investigated ALD films after the corrosion assays. The above results indicate that ALD TiO2 and Al2O3 films may be a viable alternative to replace the synthetic resin coatings frequently used in aluminum cans of use in the food industry.

Due to the rapid development and popularity of the Internet, cloud computing has become an indispensable application service. However, how to assign various tasks to the appropriate service nodes is an important issue. Based on the reason above, an efficient scheduling algorithm is necessary to enhance the performance of system. Therefore, a Three-Layer Cloud Dispatching (TLCD) architecture is proposed to enhance the performance of task scheduling. In first layer, the tasks need to be distinguished to different types by their characters. Subsequently, the Cluster Selection Algorithm is proposed to dispatch the task to appropriately service cluster in the secondly layer. Besides, a new scheduling algorithm is proposed to dispatch the task to a suitable server in a server cluster to improve the dispatching efficiency in the thirdly layer. Basically, the TLCD architecture can obtain better task completion time than previous works. Besides, our algorithm and can achieve load-balancing and reliability in cloud computing network.

The ocean’s mixed layer depth (MLD) plays an important role in understanding climate dynamics, especially during extreme weather occurrences like hurricanes. This study investigates the effects of Hurricane Katrina (2005) on the MLD in the Gulf of Mexico, using the Delft3D modeling system. By integrating hydrodynamics and wave dynamics modules, we simulate the ocean’s response to extreme weather, focusing on temperature, salinity and MLD variations. Our analysis reveals significant cooling and mixing induced by Katrina, resulting in spatial and temporal fluctuations in temperature (~± 4°C) and salinity (~± 2.5 ppt). The MLD is estimated using a simple threshold method, revealing a substantial deepening to ~120 m on August 29th-30th during Hurricane Katrina in the middle of northern Gulf of Mexico, compared to an average MLD of ~20-40 m during pre-storm conditions. It took about 18-days to recover to ~84% of the pre-storm level after Katrina. Compared to the stand-alone FLOW model, the coupled FLOW+WAVE model yields a deeper MLD of ~5%. The MLD recovery and wave effect on the MLD provide insights from various scientific, environmental and operational perspectives, offering a valuable basis for ocean management, planning and applications, particularly during extreme weather events.

Internet of Things (IoT) is a massive network of tiny devices connected internally and to the in-ternet. It is uniquely identified in the network (i.e. dedicated IP) and can share the information with other devices. However, the low power and low resources that distinguish IoT devices render them unsecure and targeted by different kinds of attacks since IoT devices cannot toler-ate heavy security models. Also, due to the heavy nature of famous protocols such as HyperText Transport Protocol (HTTP), it is costly to be used with IoT devices, and alternatively, different lightweight protocols are implemented to fit IoT devices. One of the prevailing protocols used over IoT networks is the Constrained Application Protocol (CoAP). Therefore, CoAP is popular, and that makes it targeted by different types of attacks. One of the major attacks that target CoAP is distributed denial of service (DDoS) attacks. DDoS aims to overwhelm the resources of the target and make them unavailable to legitimate users. As a result, different kinds of meth-ods were used to secure CoAP against DDoS attacks such as Datagram Transport Layer Secu-rity (DTLS) and Lightweight and Secure Protocol for Wireless Sensor Networks (LSPWSN). However, the existing models suffer from two issues: DTLS is not designed for constrained devices and is considered a heavy protocol. Besides, LSPWSN is working over the network layer, not in the application layer that CoAP works on. In this paper, we build a machine learn-ing model that can detect the DDoS attacks against CoAP with an accuracy of 98%. The CIDAD dataset is extended from ~11000 to 100,000 samples using GANs because it has fewer samples of malware (less than 0.2% of the total dataset). Our model outperforms the existing models that target securing CoAP in the application layer and obtains 93% of accuracy.

Abstract- Cognitive radio (CR) play an important role in improving spectral efficiency (SE) of wireless communication, meanwhile, intelligent reflecting surface (IRS) is an effective technology to improve the secrecy performance of wireless communication system by adjusting the phase shift and amplitude of channel. Thus, we consider an IRS-aided multiple-input single-output (MISO) CR systems to enhance secrecy rate, which is consists of a single eavesdropping link, a primary network containing the primary receiver (PR), and secondary network including secondary receiver (SR) and the SR transmitter (SR-TX). Specifically, we minimize the transmit power of SR subject to secrecy capacity constraint and interference temperature (IT) constraint on PR, by jointly optimizing the beamforming vector and artificial noise (AN) constraints matrix at SR-TX as well as the phase shift matrix of IRS. Numerical results show that the different values of transmit antennas at the SR-TX and the number of IRS elements can significantly decrease the transmit power under the condition of ensuring secure communication.

In this paper, the results of finite element analyses of a single-layer cylindrical latticed shell under severe earthquake is presented. A 3D Finite Element model using fiber beam elements were used to investigate the collapse mechanism of this type of shell. The failure criteria of structural members are simulated based on the theory of damage accumulation. Severe earthquake of peak ground acceleration (PGA) of 500 gal was applied to the shell. The stress and defeomation of the shell were studied in detail. A three-stages collapse mechanism “double-diagonal -members-failure-belt” of this type of structure was discovered. Based on the analysis results, the measures to mitigate collapse of this type of structure is recomanded.

Sound absorbing materials are used in building to dissipate sound energy into heat by viscous and thermal processes. Sound absorbers increase the transmission loss of walls, decrease the reverberation time of rooms and attenuate the noise generated by internal sound sources. Porous absorbers (fibrous, cellular or granular) are the most used materials in noise control applications, since their high performance-to-cost ratio in the frequency band of interest. However, when cleaning and health reasons are of concern, microperforated panel (MPP) absorbers can be preferred. MPPs, consisting of many minute (sub-millimetric) holes in a panel, are tunable absorbers in a prescribed frequency band, which main shortcomings are high manufacturing cost and limited absorption frequency band. Production cost of MPP can nowadays be drastically cut down by means of modern techniques. Absorption frequency band can be considerably enlarged by designing multiple-layer MPPs (ML-MPPs). The aim of this article is to review the high potential of ML-MPPs as a modern, clean and healthy alternative of porous materials for sound absorption.

In this study, multi-layer ceramic capacitors (MLCCs) detached from lighting sector's waste electrical-electronic equipment (WEEE) are characterised for the presence of rare earth elements (REEs) and precious metals (PMs). Their digestion was carried out with HNO3 & aqua regia on a heating plate and characterised with the use of inductively coupled plasma optical emission spectroscopy (ICP-OES) & scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The contents of REEs and PMs are 0.84 wt% and 0.60 wt%, respectively, and create an economic stored value in MLCCs that is essentially defined by PMs of 98.67% and by Pd 78.37%. The content of the main elements is: Nd 0.366 wt%, Y 0.220 wt%, Dy 0.131 wt%, Ag 0.467 wt%, and Pd 0.105 wt%. The results confirm the need of selective removal and separate recycling process of MLCCs from WEEE drivers.

Determining accurate PM2.5 pollution concentrations and understanding their dynamic patterns is crucial for scientifically informed air pollution control strategies. Traditional reliance on linear correlation coefficients for ascertaining PM2.5 related factors only uncovers superficial relationships. Moreover, the invariance of conventional prediction models restricts their accuracy. To enhance the precision of PM2.5 concentration prediction, this study introduces a novel integrated model that leverages feature selection and a clustering algorithm. Comprising three components - feature selection, clustering, and integrated prediction, the model first employs the non-dominated sorting Genetic Algorithm (NSGA-III) to identify the most impactful features affecting PM2.5 concentration within air pollutants and meteorological factors. This step offers more valuable feature data for subsequent modules. The model then adopts a two-layer clustering method (SOM+K-means) to analyze the multifaceted irregularity within the dataset. Finally, the model establishes the Extreme Learning Machine (ELM) weak learner for each classification, integrating multiple weak learners using the Adaboost algorithm to obtain a comprehensive prediction model. Through feature correlation enhancement, data irregularity exploration, and model adaptability improvement, the proposed model significantly enhances the overall prediction performance. Data sourced from 12 Beijing-based monitoring sites in 2016 were utilized for an empirical study, and the model's results compared with five other predictive models. The outcomes demonstrate that the proposed model significantly heightens prediction accuracy, offering useful insights and potential for broadened application to multifactor correlation concentration prediction methodologies for other pollutants.

Current methods for the hardening step of functional coatings over different materials imply the use of high temperatures, high energy consumption or long periods of time, which have repercussions on the speed and cost of the product. We report here a simple and low cost methodology for the functionalization of low cost stainless steel, which is modular, depending of the functionality pursued: a levelling layer for smooth the surface of the material, an “easy to clean” property, or both of them. The research is based on sol-gel coatings cured under UV light without requiring high thermal hardening processes making it applicable to plastics and other sensible materials and possessing high chemical and thermal stability. The film ensures lower processing costs, and higher rates of hardening if the adequate medium-pressure lamps are employed. This formulation is also well defined for scaling up the process, so it is possible to perform a continuous coating in large areas by employing mild processing conditions (low temperature, atmospheric pressure). In addition, the sol gel solution was fully characterized and studied in order to guarantee a long service life before deposition, with a focus on industrial applications in the domestic sector.

Variations in geochemical signatures of fossil brachiopod shells may be due to diagenesis and/or biological processes (i.e. ‘vital effects’). Characterize them is crucial to identify reliable areas into the shell suitable to paleoclimatological studies. This investigation contributes to an in-depth understanding of geochemical variations of Gigantoproductus sp. shells (SW Spain, Serpukhovian age), which could affect to the Late Paleozoic Ice Age interpretation. Microstructural, crystallographic, cathodoluminescence and geochemical (minor and trace elements, δ18O, δ13C, and strontium isotopes) characterisation have been performed on the tertiary layer of the ventral valve, to assess the preservation state. Poorly-preserved areas exhibit microstructural and geochemical changes such as recrystallisation, fracturing and higher Mn and Fe enrichment. Moreover, these areas have higher dispersion of ⁸⁶Sr, ⁸⁷Sr, δ18O and δ13C than well-preserved areas. Three structural regions have been identified in well-preserved areas of ventral valve by differences in valve curvature and thickness, such as the umbonal, thick and thin regions. These regions have different proportions of Mg, S, Na, δ18O, and δ13C, whom are interpreted as ‘vital effects’ and probably are related with growth rate differences during shell growth. Gigantoproductus tertiary layer seems the best suitable to paleoclimatological studies because it retains the original microstructure and geochemistry.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

The presence of bubbles near the sea surface under certain conditions leads to abnormal sound scattering and a significant change in the acoustic properties of the upper layer of the sea. The article presents some results of sound scattering studies under various sea conditions, up to stormy conditions, when extensive bubble clouds arise. By the method of unsteady acoustic spectroscopy, data on the size distribution of bubbles at various depths have been obtained, which can be described by a power function with exponential decay at small bubble sizes of the order of 10 microns. Estimates of the gas content in bubble clouds and their influence on the acoustic characteristics of the upper layer of the sea have been carried out. It is shown that at sufficiently high concentrations, sharp increases in absorption and dispersion of the sound velocity are observed. Modeling of sound propagation in the presence of a quasi-homogeneous bubble layer shows that it leads both to a change in the laws of the average decay of the sound field along the sound propagation path and to a change in the shallow spatial structure of the field.

Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO₂), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 10²⁰ cm⁻³ and 10–20 cm²/Vs, which are typical values for SnO₂ films, and show a negligible temperature dependence from room temperature down to -269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO₂ samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

Emotion recognition defined as identifying human emotion and is directly related to different fields such as human-computer interfaces, human emotional processing, irrational analysis, medical diagnostics, data-driven animation, human-robot communi- cation and many more. The purpose of this study is to propose a new facial emotional recognition model using convolutional neural network. Our proposed model, “ConvNet”, detects seven specific emotions from image data including anger, disgust, fear, happiness, neutrality, sadness, and surprise. This research focuses on the model’s training accuracy in a short number of epoch which the authors can develop a real-time schema that can easily fit the model and sense emotions. Furthermore, this work focuses on the mental or emotional stuff of a man or woman using the behavioral aspects. To complete the training of the CNN network model, we use the FER2013 databases, and we test the system’s success by identifying facial expressions in the real-time. ConvNet consists of four layers of convolution together with two fully connected layers. The experimental results show that the ConvNet is able to achieve 96% training accuracy which is much better than current existing models. ConvNet also achieved validation accuracy of 65% to 70% (considering different datasets used for experiments), resulting in a higher classification accuracy compared to other existing models. We also made all the materials publicly accessible for the research community at: https://github.com/Tanoy004/Emotion-recognition-through-CNN.

Wind power as a renewable source of energy, has numerous economic, environmental and social benefits. In order to enhance and control the renewable wind power, it is vital to utilize models that predict wind speed with high accuracy. Due to neglecting of requirement and significance of data preprocessing and disregarding the inadequacy of using a single predicting model, many traditional models have poor performance in wind speed prediction. In the current study, for predicting wind speed at target stations in the north of Iran, the combination of a multi-layer perceptron model (MLP) with the Whale Optimization Algorithm (WOA) used to build new method (MLP-WOA) with a limited set of data (2004-2014). Then, the MLP-WOA model was utilized at each of the ten target stations, with the nine stations for training and tenth station for testing (namely: Astara, Bandar-E-Anzali, Rasht, Manjil, Jirandeh, Talesh, Kiyashahr, Lahijan, Masuleh and Deylaman) to increase the accuracy of the subsequent hybrid model. Capability of the hybrid model in wind speed forecasting at each target station was compared with the MLP model without the WOA optimizer. To determine definite results, numerous statistical performances were utilized. For all ten target stations, the MLP-WOA model had precise outcomes than the standalone MLP model. The hybrid model had acceptable performances with lower amounts of the RMSE, SI and RE parameters and higher values of NSE, WI and KGE parameters. It was concluded that WOA optimization algorithm can improve prediction accuracy of MLP model and may be recommended for accurate wind speed prediction.

Studies on the detection of layers with elevated black carbon aerosol (BC) concentrations and the formation conditions of these layers help understand the vertical distribution of BC concentrations, which will provide a basis for the assessment of climate effects and early BC pollution warnings. By using the Weather Research and Forecasting with Chemistry (WRF-Chem) numerical model, we performed a numerical simulation analysis on the authenticity of strong elevated BC concentration layers that were detected by an aircraft in the mixing layer over Harbin, China, which is a high-emission area, on a clear sunny afternoon in the early heating period of 2016. We then discuss possible problems and solutions when non-vertical paths are used to detect the vertical distribution of BC concentrations. Finally, we discuss the favorable conditions for the formation of elevated BC concentration layers by weak vertical flow. The results show that the horizontal variability of BC concentration in the mixing layer in the observation area in Harbin was sufficiently large during the measurement. This produced a false elevated layer, as detected by the aircraft during one round of spiral flight in the mixing layer. The root mean square of the horizontal distribution of BC concentration did not change with height in the mixing layer during the daytime, but it decreased with the thickness of the mixing layer and was higher in the mixing layer than in the free atmosphere. Therefore, the thinner the mixing layer, in which the vertical distribution of the BC concentration is detected in an inclined path, the stronger interference of the horizontal variability on the detected results. When a spiral flight detection path is used, the aircraft should fly at least two rounds in the mixing layer. In the daytime, due to strong turbulence in the mixing layer, weak vertical uplift is not favorable for the occurrence of elevated BC concentration layers in the mixing layer. In the nighttime, if weak vertical uplift is well matched with the BC concentration or its vertical gradient, elevated BC concentration layers can be formed in the atmosphere. Compared with upper layers far from the ground, nighttime elevated layers are easier to form in lower layers near the ground because high BC concentrations or large vertical gradients are more likely to occur in the lower layers. Both cases facilitate the occurrence of large vertical upward transport rates of BC.

An increased demand for natural products nowadays most specifically probiotics (PRO) is evident since it comes in conjunction with beneficial health effects for the consumers. In this regard, it is well known that encapsulation could affect positively the PRO's viability throughout food manufacturing and long-term storage. This paper aims to analyze and review various multilayer strategies for encapsulation of PRO. Double-layer encapsulation of PRO by electro-hydrodynamic atomization or electrospray technology has been reported along with layer-by-layer assembly and water-in-oil-in-water (W1/O/W2) double emulsions to produce multilayer PRO-loaded carriers. Finally, their applications in food products are presented. The resistance (cover material) and viability of (PRO) to mechanical damage, during gastrointestinal transit and shelf life of these trapping systems are also described. The PRO encapsulation in double and multiple-layer coatings combined with other technologies can be examined to increase the opportunities for new functional products with amended functionalities opening a novel horizon in food technology.

The influences of doped hole transporting layer (HTL) on the performances of perovskite solar cells were studied. The influences of electrostatic and surface roughness effect by solvent additive doping were compared. The electrostatic effect of solvent additive doping was compared by addition of 1,8-diiodooctane and 1,8-dichlorooctane to the HTL layer. The surface roughness effect of solvent additive doping was examined using atomic force microscopy. The perovskite crystallinity by doping HTL was studied by X-ray diffraction. The conductivity of HTL was measured using four probe methods and was higher for doped devices. Enhanced conductivity of PEDOT:PSS film was also proved using fluorescence emission quenching. Long-term stability of the device was enhanced by doping HTL. The device with solvent additive exhibited much enhanced stability, retained over 80% of the initial PCE for 400 hours, while PCE of the device without solvent additive decreased to less than 80% after 200 hours. A very weak power microwave treatment was used for post-annealing of the fully fabricated devices. Post-annealing enhanced the lifetime of the device. Comparing different size of cells, the device lifetime was decreased as the cell area increased and as the size of the cell increased, the extent of lifetime enhancement by doping was increased.

Road collisions are among the world’s critical issues causing many casualties, deaths, and economic losses. To deal with this scenario, precise analysis is required. In this paper, we use Machine Learning (ML) techniques to assess and predict road traffic collisions. An ensemble machine learning model with two layers was developed to analyze simulation data from the driving simulator. The first (base) layer integrates supervised learning techniques namely, k- Nearest Neighbors (k-NN) AdaBoost, Naive Bayes (NB), and Decision Trees (DT). The second layer predicts road collisions by combining the base layer outputs by employing the stacking ensemble method using logistic regression as a meta-classifier. The data for this study were imbalanced; therefore, we performed a SMOTE resampling strategy to handle the dataset imbalance. To simplify the model, the PSO algorithm was used to select the most important features in our dataset. The two-layer ensemble model proposed had the best outcomes with an accuracy of 88%, F1 score of 83%, and an AUC of 86% as compared with k-NN, DT, NB, and AdaBoost.

In the aerospace sector, structural and non-structural components are usually subjected to a wide range of environmental conditions. Although lightweight, the use of composite parts for these applications is restricted, due to their poor performance in severe environmental conditions. Specifically, moisture can seriously damage the materials' performance, reducing their mechan-ical, thermal, electrical, and physical properties as well as the service time. A strategy to improve the materials’ resistance in humid environments is the use of protective lightweight barrier coatings to reduce the diffusion of gases and/or liquids in composites. Nanolamellar nanocom-posite characterized by the high in-plane orientation of nanoplatelets effectively works as barrier structures by generating tortuous paths for molecule diffusion. In this work, the effectiveness of protection against water uptake of nanocomposites reinforced with Graphite NanoPlatelets (GNPs) at high filler content (70, 80 and 90%wt) for Kevlar sandwich panels of a nacelle engine of an ATR42 aircraft has been investigated. Moisture uptake and Ground Air Ground (GAG) tests were carried out in an environmental chamber to reproduce temperature and relative humidity profiles representative of a real-scale application for a regional aircraft composite part. The high filler content of the graphene films ensures a high level of tortuosity by delaying and reducing moisture absorption by –71% compared to the unprotected panel, showing good barrier properties.

Chronoamperometric curves of the oxidation of a ferrocenyl derivative by the potential step showed diffusion controlled-like currents less than the Cottrell's equation at a platinum wire electrode. The lower deviation cannot be explained by the Butler-Volmer heterogeneous kinetics, but was ascribed to the negatively capacitive current associated with the redox reaction. The deviation at the fully oxidized potential corresponds to the non-zero concentration at the electrode surface, which cannot be predicted from the Nernst equation. The Nernst equation expresses the relationship of the potential with the activity at the electrode surface rather than the concentration. The diffusion equation provides the relation of the current with the surface concentration rather than the activity. The negative capacitance or the non-zero concentration may arise from structure formation on the electrode owing to the dipole-dipole interaction, which is similar to the generation of the double layer capacitance including frequency dispersion. On this concept, we derive here expressions for the lowered diffusion-controlled current and the time-dependent surface concentration. The negatively capacitive current shows the time-dependence of t-0.9, which is similar to the decay of the double layer capacitive currents. The surface concentration decays with the t-0.4-dependence.

Video behavior recognition often needs to focus on object motion processes. In this work, a self-organizing computational system oriented to behavioral clustering recognition is proposed, which achieves the extraction of motion change patterns by binary encoding and completes motion pattern summarization using a similarity comparison algorithm. And in the face of unknown behavioral video data, a self-organizing structure with layer-by-layer accuracy progression is used to achieve motion law summarization by using a multi-layer agent design approach. Finally, the real-time feasibility is verified in the prototype system using real scenes to provide a new feasible solution for unsupervised behavior recognition and space-time scenes.

The perpendicular exchange bias effect is observed in the ferromagnetic Co/Ni multilayers adjacent to the antiferromagnetic FeRh layer. It is found that as the antiferromagnetic FeRh thickness increases from 10 Å to 50 Å, the hysteresis loop is gradually changed from the symmetric shape to the asymmetric shape shifted by some amount corresponding to the exchange-biased field at the thickness of 25 Å. Also, the magnetic domain observation experiment confirms that the domain reversals in the increasing and the decreasing field regions of the sample with the thickness of 50 Å exhibit the same single domain wall motion even though they have the different coercivities.

We report on the fabrication and electrical characteristics of zinc-oxide (ZnO) based metal-insulator-semiconductor (MIS) type Schottky barrier diodes (SBHs). ZnO thin layer on the p-type silicon substrate was fabricated by atomic layer deposition (ALD). The structure and surface properties of the thin film were characterized by X-ray diffraction (XRD), atomic force microscope (AFM) and secondary ion mass spectrometer (SIMS). The current-voltage (I-V) characteristics of Al/ALD-grown ZnO/p-Si diodes were measured under dark at room temperature. The electrical parameters such as ideality factor (n), series resistance (R_s) and barrier height (ϕ_b) of the diodes were analyzed using standard thermionic emission (TE) theory, Norde and Cheung method. The barrier height value obtained from I-V and Cheung method was found to be 0.73 eV and 0.76 eV, respectively. The interface state density (Dit) of the diodes was determined from the I-V characteristics. The nonideal behavior of measured parameters suggested the presence of interface states. The obtained results showed that the prepared diode can be used for NIR Schottky photodetector applications.

In this study, Fe-Mo-B based hardfacing electrodes containing different amounts of Mo were coated on an AISI 1020 steel substrate using the electric arc welding method. The findings show that molybdenum is highly effective on the microstructure and minor changes in the coating composition affect the phases and morphological properties. In the hardness tests, an increase of 73% was achieved in the Fe14Mo2B4 based hardfacing coating compared to the base material and a 30% increase compared to the Fe16B4 based coating. The highest macro hardness value was measured as 56.4 HRC and the highest phase hardness was measured as 3228 HV in the FeMo2B2 phase. The lowest wear rate was measured in the Fe14Mo2B2 based coating. The wear rate of the Fe14Mo2B4 based coating was 8.1 times lower than that of the substrate material and 4.7 times lower than that of the Fe16B4 based coating. According to corrosion test results, the highest corrosion resistance was obtained in Fe16B4 based coating. The current density value of the Fe16B4 based coating was measured to be 13.6 times lower than that of the substrate material.

Electrochemical deposition of silicon at room temperature is problematic due to intrinsically low conductivity of the deposits. This study reports the photoelectrochemical (PEC) deposition of silicon (Si) and silicon–carbon (Si–C) layers from an ionic liquid at temperature 40 oC using silicon tetrachloride (SiCl4) as a silicon precursor. Amorphous layers are deposited on p-type silicon (p-Si), p-type gallium arsenide (p-GaAs), and aluminum–copper alloy AA2024. The semi-conductor substrates are activated by white LED illumination, which generated photoelectrons, thereby making the substrate conductive with respect to the cathodic reaction. Photoresponsive-ness of the deposits is proven by the light-induced photocurrents on an optically inactive substrate made of the alloy AA 2024. The proposed method paves the way for the electrochemical modifica-tion of semiconductors and metals with Si and Si–C structures, which are applicable in various fields, such as; batteries, anti-corrosion coatings, photovoltaics, or PEC electrodes for hydrogen production.

The problem of health status prediction of insulated-gate bipolar transistors (IGBTs) gains a lot of attention in the field of health management of power electronic equipment. The performance degradation of IGBT gate oxide layer is one of the important failure modes. In view of failure mechanism analysis and easy implementation of monitoring circuit, this paper selects the gate leakage current of IGBT as the precursor parameter of gate oxide degradation, and uses time domain characteristic analysis, gray correlation degree, Mahalanobis distance, Kalman filter and other methods to carry out feature selection and fusion, and finally obtains a health indicator characterizing the degradation of IGBT gate oxide. Based on the Convolutional Neural Network and Long Short-Term Memory (CNN-LSTM) network, this paper constructs an IGBT gate oxide degradation prediction model, and performs experimental analysis on the dataset released by NASA-Ames Laboratory, and the average absolute error of performance degradation prediction is as low as 0.0216. Compared with Long Short-Term Memory (LSTM), Convolutional Neural Network (CNN), Support Vector Regression (SVR) and CNN-LSTM models, CNN-LSTM network has the highest prediction accuracy. These results show the feasibility of gate leakage current as a precursor parameter of IGBT gate oxide layer failure, as well as the accuracy and reliability of the CNN-LSTM prediction model.

Hydropericardium hepatitis syndrome (HHS) caused by fowl adenovirus-4 have been frequently reported in commercial chickens from several countries causing significant economical losses. In Azerbaijan, fowl adenovirus infections in broiler and layer breeders flocks cause severe disease and mortality. Here we investigated the pathological lesions and the dissemination of fowl adenovirus-4 into the visceral organs of infected birds. Tissue samples containing liver, heart and spleen from 20 necropsied chickens were collected on the FTA cards and presence of fowl adenovirus was analysed by PCR and sequencing. Postmortem findings of both broiler and layer breeder chickens were similar, and the most affected organs were the liver with hepatitis and the heart with hydropericardium lesions. Other postmortem signs include swollen kidneys with haemorrhages and small white foci on the surface of the spleens. In some birds intestinal congestion and ecchymotic hemorrhages were also apparent. The PCR analysis revealed that all collected organs from 20 birds showed presence of fowl adenovirus-4 genome. The sequence analysis showed that fowl adenovirus-4 prevalent in Azerbaijan carry more closer phylogenetic relationship with the viruses prevalent in the Middle East, Far East and Indian subcontinent. However, a distinct diversity was seen from the strains prevalent in Europe, North and South America. This study will provide evidence the impact of fowl adenovirus-4 on the poultry production and improved preventive disease control strategies are required to reduce the HHS disease in chickens in Azerbaijan.

Image encryption is increasingly becoming an important area of research in information security and network communications, as digital images are widely used in various applications and are vulnerable to various types of attacks. In this research work, a color image cryptosystem that is based on a 3-layer permutation-substitution network (PSN) is proposed. For every layer, an encryption key and an S-box are generated and utilized. Those are based on a four-dimensional (4D) dynamical Chen system of a fractional-order, the Mersenne Twister, OpenSLL, Rule 30 Cellular Automata and Intel’s MKL. The sequential application of Shannon’s ideas of diffusion and confusion for 3 times guarantees a total distortion of any input plain image, resulting in a totally encrypted one. Apart from the excellent and comparable performance to counterpart algorithms from the literature, showcasing resistance to visual, statistical, entropy, differential, known plaintext and brute-force attacks, the proposed image cryptosystem provides an exceptionally superior performance in 2 aspects: a vast key space of 2^1658 and an average encryption rate of 3.34 Mbps. Furthermore, the proposed image cryptosystem is shown to successfully pass all the tests of the NIST SP 800 suite.

To enable purposeful design and implementation of automated concrete technologies, precise assessment and prediction of the complex material flow at various stages of the process chain are necessary. This paper investigates the intermediate stage of the extrusion and deposition processes in extrusion-based 3D-concrete-printing, using a numerical model based on the Particle Finite Element Method (PFEM). In PFEM, due to the Lagrangian description of motion, remeshing algorithms and the alpha shape method are used to track the free surface during large deformation scenarios. The Bingham constitutive model was used for describing the rheological behaviour of fresh concrete. This model is validated by comparing the numerically predicted layer geometries with those obtained from laboratory 3D printing experiments. Extensive parametric studies were then conducted using the numerical simulation, delineating the influence of process and material parameters on the layer geometries, the dynamic surface forces generated under the extrusion nozzle and the inter-layer interactions.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

To gain insight into the differences between onshore and offshore atmospheric turbulence, 2 pressure fluctuations were measured for offshore wind under different environmental conditions. 3 A durable piezo-electric sensor was used to sample turbulent pressure data at 50 kHz. Offshore 4 measurements were performed at 100 m height on Germany’s FINO3 offshore platform in the 5 German Bight together with additional meteorological data provided by Deutscher Wetterdienst 6 (DWD). The statistical evaluation revealed that the stability state in the atmospheric boundary has a 7 large impact on turbulent fluctuations. Therefore, we used higher statistical properties (described 8 by so-called shape factors) to the stability state. Data was classified to be either within the unstable, 9 neutral or stable stratification. We found that in case of stable stratification, the shape factor is 10 mostly close to zero, indicating that a thermally stable environment produces closer-to Gaussian 11 distributions. Non-Gaussian distributions were found in unstable and neutral boundary layer states 12 and an occurrence probability was estimated. Possible impact on laminar-turbulent transition on the 13 blade is discussed with application of so-called laminar aerofoils on wind turbine blades. Use of a 14 cut-off frequency to separate load and aerodynamic turbulence is proposed.

Little is known about how the degree of mixing of forest-forming species affects forest floor hydrology. We evaluated the water storage capacity of the resulting litter layer by mixing litterfall of Scots pine and sessile oak and studying their decomposition time. We prepared 90 artificial samples containing pure pine litter, pure oak litter, and mixed pine-oak litter with varying shares of pine needles. These samples were subjected to 15 months of decomposition in soil. After every three months of decay, some samples were removed from the soil, and their water storage capacity, bulk density, and C:N ratio were evaluated. Our findings indicate that samples with the greatest water storage capacity had a low C:N ratio and a predominant share of oak leaves. Conversely, samples with a high C:N ratio and a predominant share of pine needles had the lowest water storage capacity. After 12 and 15 months of decomposition, the water storage capacity increased by more than 52% compared to the initial water capacity of the samples. The highest increase in water storage capacity (>40%) was observed in samples with a predominant share of oak leaves, while the lowest (approximately 28%) was recorded in samples with 80 and 100% of pine needles.

Titanium dioxide (TiO2) thin films have been widely used in transparent optoelectronic devices owing to their excellent optical properties also is used in photocatalysis, cosmetics, and many other biomedical applications. However, a lack of studies was published on microstructure and adherence comparison of the TiO2 deposited on both AISI substrates. In this work, TiO2 thin films were deposited onto AISI 304 and AISI 316L stainless steel (SS) substrates via atomic layer deposition. Its heterostructure, morphology, and adhesion were compared in both substrates looking for synergistic and multifunctional properties. Raman spectroscopy mapping and X-ray diffraction using the Rietveld refinement method showed that the films are composed of anatase and rutile phases in different percentages. Scratching tests were used to analyze the film adher-ence and friction between a diamond tip and TiO2 film, showing well adhered in both substrates.