In the present work report, the MgAl₂O₄and the Ag/MgAl₂O₄ samples were successfully synthesized by the modified hydrothermal and the isovolumetric impregnation methods, respectively. The structural properties of the prepared samples were systematically characterized by XRD, SEM, TEM, DRS, XPS and et al techniques. The photocatalytic degradation of methylene blue by the Ag/MgAl₂O₄ and MgAl₂O₄ samples was comparatively studied under UV lamp irradiation. The results revealed that the prepared Ag/MgAl₂O₄ (pH=6) samples were the most active among the samples in photocatalytic of methylene blue. Under UV lamp irradiation, the Ag/MgAl₂O₄ (pH=6) photodegradation of methylene blue reached to 89.6% within 120 min. And the Ag/MgAl₂O₄ (pH=6) complex photocatalysts displayed a high photochemical stability under repeated irradiation. Repeated irradiate the Ag/MgAl₂O₄ (pH=6) compound, which indicated it had a high photochemical stability.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Abstract: Development of the fast neutron radiography with higher penetration capability in Non-Destructive Testing (NDT) techniques is rapidly. The detection efficiency and the imaging spatial resolution are the main problem of the radiography detector for many fast neutron imaging systems. In this paper, a detector composed of pixelated EJ200 scintillator array，an 16 × 16 silicon-photomultipliers (SiPM) array, and a capacitive multiplexing network readout electronics is designed. Using Monte-Carlo simulations，the main parameters of the detector was optimization. Then the detector prototype was fabricated and tested at a 14 MeV D-T neutron source. The preliminary test results showed that the prototype has spatial resolution of 1.26 mm. Using pixelated scintillator structure，the conflict between spatial resolution and detect efficiency could improved. Moreover, SiPMs offer a flexibility for the expansion of application field of the imaging system due to their excellent photon detection performance, relatively low price and joint possibility for large area.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

With the development of salt cavern gas storage construction technology, the construction of large-scale gas storage salt caverns using sediment voids is expected to solve the problem of low effective volume formation rate and poor construction economy of high-impurity salt mines. There are few studies on the long-term operation mechanical behavior of salt cavern gas storage under the influence of sediment accumulation currently. This paper studies the influence of sediment accumulation height, particle gradation, and operating pressure on the stability of salt caverns by constructing a coupling model of sediment particle discontinuous medium and surrounding rock continuous medium. The continuous-discontinuous coupling algorithm is suitable for analyzing the influence of particle accumulation height and particle gradation on the creep shrinkage of salt caverns. The increase of sediment accumulation height slows down the creep shrinkage of the bottom of the salt cavern, strengthens the restraining effect on the surrounding rock of the cavern, and moves the position of the maximum displacement of the surrounding rock to the upper part of the cavern; the sediment particle gradation has little effect on the cavern volume shrinkage rate, and the greater the coarse particle content, the smaller the cavern volume shrinkage rate; the greater the operating pressure, the more conducive to maintaining the stability of the cavern, slowing down the upward movement of the sediment body and increasing the gas storage space in the upper part of the cavern. This research results can provide a reference for evaluating the long-term operation stability of sediment-type high-impurity salt cavern gas storage.

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

This paper introduces a three-layer system, proposing a comprehensive model of granular mixture transport over a mobile sloped bed in a steady flow. This system, consisting of the bottom, contact and upper zones, provides complete, continuous sediment velocity and concentration vertical profiles. The model considers gravity’s effect on sediment transport in the bottom (dense) layer, a crucial factor often overlooked in previous studies. The induced movement in the mobile sublayer of the dense layer causes an increase in velocity at the upper boundary of this layer, significantly affecting the vertical distributions of velocity and concentration above this layer. We described the interactions between fractions and an intensive sediment mixing and sorting process in the contact layer. The proposed shear variation, with an increase in its maximum value at the bed, adds to the novelty of our approach. The data sets used for the model’s validation cover various conditions, including slopes, grain diameters, densities and grain mobility conditions, from incipient motion to a fully mobilised bed. This extensive validation process instils confidence in the theoretical description and its applicability to real-world scenarios.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

The atomic structures of Zn and Na borophosphate glasses were studied by X-ray and neutron diffraction. Peaks assigned to the B−O, P−O, and O−O distances confirm that only BO4 units co-exist with the PO4 tetrahedra. The Zn−O and Na−O coordination numbers are found to be a little larger than four. The narrowest peaks of the Zn−O first-neighbor distances exist for the glasses along a line connecting the Zn(PO3)2 and BPO4 compositions (50 mol% P2O5) which is explained by networks of ZnO4, BO4, and PO4 tetrahedra with twofold coordinated oxygens. Calculated amounts of the available oxygen support this interpretation. Broadened peaks occur for glasses with lower P2O5 contents, consistent with the presence of threefold coordinated oxygens. The two distinct P−O peak components of the Zn and Na borophosphate glasses differ in their relative abundances which is interpreted by Na+ cations that coordinate oxygens in some P−O−B bridges, something not seen for the Zn2+ ions.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

The information on the land use and soil conservation practice based on year 2006, 2010 and 2014, hence offering an opportunity to model the impacts of land use change on erosion, deposition and surface water runoff. Limitation in the use of hydrological models had been their inability to handle the large amount of input data that describe the heterogeneity of the natural system. In this study, a procedure that takes into account soil conservation practice based on the land use change, the response of soil erosion and sediment export from the George Town Conurbation catchment area, and average annual sediment yields were estimated for each grid cell of the watershed to identify the critical erosion areas of rural and urban planning proposes. Average annual sediment yield and data on a grid basis estimated using Universal Soil Loss Equation (USLE) and an emerging technology represented by Geographic Information System (GIS) used as a tool to produce a map for erosion rate. The changing of the land use from forest to agriculture and then to an urban area is a challenging task to research on land use demand for population, and environmental impact assessment is important for the planning of natural resources management, allowing research the modification of land use properly and implement more sustainable for long term management strategies. The challenge is to formulate strategies that would promote an integrated approach to the land use planning at an appropriate level as to address the issues that arose. Modelling for creating urban growth boundary for the George Town Conurbation must have to be controlled surface runoff and soil loss and sediment export from land use of the George Town Conurbation catchment.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

Macrophages as a source and target of GDF-15

To achieve n-type doping in diamond, extensive investigations employing first principles have been conducted on various models of phosphorus doping and boron-phosphorus co-doping. The primary focus of this study is to comprehensively analyze the formation energy, band structure, density of states, and ionization energy of these structures. It is observed that within a diamond structure solely composed of phosphorus atoms, the formation energy of an individual carbon atom is excessively high. However, the substitution of two carbon atoms leads to the conversion of diamond into a p-type semiconductor. Upon examining the P-B co-doping structure, it is revealed that the doped impurities exhibit a tendency to form more stable cluster configurations. As the separation between the freely doped atoms and the cluster impurity structure increases, the overall stability of the structure diminishes, consequently resulting in an elevation of the ionization energy. Analysis of the electronic density of states demonstrates that the electron orbit of the B atom makes negligible contributions to the impurity levels during P-B doping.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

In the contemporary world of science, continuous observation of specific fixed regions is required, awaiting the emergence of targets or phenomena within those areas to locate and identify them. Astronomy requires continuous monitoring of stars, swiftly pinpointing occurrences, such as flares, and acquiring their spectral data to aid identification. In military contexts, continuous observation of specific areas is essential for promptly locating enemy movements and obtaining target spectral data for deciphering enemy disguises. Additionally, continuous observation of experimental samples in biochemistry is mandatory to pinpoint localized changes and acquire spectral data from those areas. Hence, this paper develops a novel imaging spectrometer solution to monitor localized regions continuously. Specifically, this paper first elaborates on the developed instrument’s characteristics and optical structure, followed by optical design software simulations. The instrument has an F-number of 5, a focal length of 100mm, and a field of view covering the wavelength range from 400nm to 600nm. The optical path diagram indicates that the system’s dispersion and imaging images can be separated, meeting the system’s requirements. Besides, the Modulation Transfer Function (MTF) graph confirms that the image quality meets the requirements. Furthermore, a region-monitoring type imaging spectrometer was constructed to assess the instrument’s capability for spectral observation of fixed regions. The instrument can detect a fixed area, with the target placed within the detection area. Spectral data were successfully obtained by conducting image processing on the acquired images. The correlation coefficient between this data and reference data was as high as 0.9226, indicating the instrument’s successful measurement of the target’s spectrum. Thus, the developed instrument demonstrated that it can image the observed areas and acquire spectral data from targets within those regions.

Continuing the investigation already started (See Farcaş, A.-A.; Bende, A. PCCP 2024, 26, 14937), the light absorption and charge-transfer properties of the dopamine (DA), dopamine zwitterion (called as dopamine-semi-quinone or DsQ) and dopamine-o-quinone (DoQ) adsorbed on the graphene nanoparticle surface have been investigated using the ground state and linear-response time-dependent density functional theories, considering the B97X-D3BJ/def2-TZVPP level of theory. In terms of the strength of molecular adsorption on the surface, the DsQ form has 50 % higher binding energy than that for the DA or DoQ cases (-20.24 kcal/mol vs. -30.41 kcal/mol). The results obtained for electronically excited states and UV-Vis absorption spectra show that the photochemical behavior of DsQ is more similar to DA than that observed for DoQ. Of the three systems analyzed, the DsQ-based complex showed the most active CT phenomenon, both in terms of the number of CT-like states and the amount of charge transferred. Of the first thirty electronically excited states computed for the DsQ case, eleven are purely CT-type and nine are mixed CT and localized (or Frenkel) excitations. By varying the adsorption distance between the molecule and the surface vertically, the amount of charge transfer obtained for DA decreases significantly as the distance increases, for DoQ it remains stable, while for DsQ there are states for which little change is observed, while for others there is a significant change. Furthermore, the mechanistic compilation of the electron orbital diagrams of the individual components cannot describe in detail the nature of the excitations inside the complex.

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

Agrivoltaic agrotunnels are currently designed for high density grow walls that are not amenable to bush berries or root crops. Commercial grow bins provide deeper substrates for produce with more root systems but have high costs per unit growing area. To overcome the economic limitations of grow bins, this study applies the distributed manufacturing open-source design paradigm to develop four designs for low-cost open source structures. The designs target root vegetables and bush fruit specifically to be adopted by remote communities with limited or no outdoor growing environment to offset the market price for imported fresh produce. The indoor growing designs provide the necessary structure for supporting grow light and grow bins and enabled the transplanted berry plants to flower and produced fruits. They provide a comparable amount (110L) or more of grow volume from 106 to 192 L. The water reservoir volume for the commercial system (62 L) and grow area (0.5 m³) is surpassed by all new designs that range from 64 to 192 L and 0.51 to 0.76 m³, respectively. These superior properties are possible with material costs for all four designs that save more than 90% of the economic cost of the commercial systems.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

Baijiu is popular with its long history and balanced flavor, and flavor type was the most widely used classification mode for Baijiu. However, the evolution relationship of Baijiu flavor types and the differential markers between flavor types are still unclear, which has greatly affected the development of Baijiu industry. In this study, a total of 319 trace components were identified by gas chromatography-olfactometry-mass spectrometry and gas chromatography-mass spectrometry. Among them, 91 trace components with high odor active values or taste active values were recognized as flavor components. Then random forests were conducted to screen differential markers between derived and basic flavor types, and principal component analysis was carried out to evaluate their effectiveness in distinguishing the flavor types of Baijiu. Finally, 19 differential markers were screened and proved to effectively reveal the evolution Baijiu flavor types, and were further verified as key differential markers by addition test and correlation analysis.

In 2020, the Covid-19 outbreak led many countries across the globe to introduce lockdowns (LDs) that effectively caused most anthropic activities to either stop completely or be significantly reduced. In Europe, Italy played a pioneeristic role via the early introduction of a strict nationwide LD on March 9^th. This study is aimed at evaluating, using both chemical and meteorological data, the environmental response to that occurrence as observed by the Lamezia Terme (LMT) GAW/WMO station in Calabria, Southern Italy. The first 2020 lockdown has therefore been used as a “proving ground” to assess CO, CO₂, CH₄, BC, and NO_x concentrations in a rather unique context by exploiting the location of LMT in the context of the Mediterranean Basin. In fact, its location on the Tyrrhenian coast of Calabria and local wind circulation both lead to daily cycles where western-seaside winds depleted in anthropogenic pollutants can be easily differentiated from northeastern-continental winds, enriched in anthropogenic outputs. In addition to that, the first Italian LD occurred during the seasonal transition from Winter to Spring and, consequently, Summer, thus providing new insights on emission outputs correlated with seasons. Findings have clearly indicated BC and, in particular, CO as strongly correlated with average daily temperatures, and possibly domestic heating. CO₂’s reduction during the lockdown and consequent increase in the post-lockdown period, combined with wind data, has allowed to constrain local source of emissions located northeast from LMT. NO_x reductions during specific circumstances are consistent with hypotheses from previous research which linked them to rush hour traffic and other forms of transportation emissions. CH₄’s stable patterns are consistent with livestock, landfills, and other sources assumed to be nearly constant during LD periods.

In this paper, we present a full coverage path planning (CPP) algorithm for the marine surveys conducted in the convex polygon shaped search area. The survey is supposed to carry out by torpedo-type AUVs (autonomous underwater vehicles). Due to their nonholonomic mechanical characteristics, these vehicles have nonzero minimum turning radius. For any given polygon shaped search area, it can always be partitioned into one or more convex polygons. With this in mind, this paper proposes a novel search algorithm called CbSPSA (Calculation based Shortest Path Search Algorithm) for full coverage of any given convex polygon shaped search area. By aligning the search inter-tracks alongside the edge with the minimum height, we can guarantee the minimum number of the vehicle’s turns. In addition, the proposed method can guarantee the planned path is strictly located inside the polygon area without overlapped or crossed path lines, and also has the total path length as short as possible. Considering the vehicle’s nonzero minimum turning radius, we also propose a sort of smoothing algorithm to smooth the waypoint path searched by CbSPSA so as for the vehicle to exactly follow it. The smoothed path is also guaranteed to be strictly located inside the polygon. Numerical simulation analyses are also carried out to verify the effectiveness of the proposed schemes.

Background This study aimed to identify the prominent risk factors that may trigger danger signals of early onset of vascular deregulation in T1D. The risk factors we have identified may serve as dual-purpose biomarkers of rapid diagnosis that offer prospective tailor-made resolution therapeutics. Methods The healthy control (HC) was compared with individuals diagnosed with T1D for the risk factors of vascular deregulation in published research studies from year 2013 to 2023. The PubMed, Web of Science and Google Scholar databases were searched from 1/1/2013 to 1/9/2023. The risk of bias was assessed with the Cochrane (ROBINS-I ) tool, which is relevant to clinical subjects. A random effect model for continuous data was followed and analysed by RevMan 5.4 and GraphPad Prism software. Results 80 relevant case-control studies having 5293 HC and 7492 T1D patients were included. The age and sex-matched HC consisted of persons free of disease and not under any medication while clinical subjects of all age groups were included. 28 risk factors were grouped into six primary outcome models, all of which favoured the T1D synonymous with a high risk of CVD. Conclusions Our findings have strong implications for improving the quality of life and health economics related to vascular disease in T1D. HbA1c% is the most effective biomarker, followed by FBG, LDL-C, and AI% which the clinicians could evaluate using a simple blood test or non-invasive techniques. (Protocol registered at https://www.crd.york.ac.uk/prospero/ CRD42022384636).

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Despite the effectiveness of insulin injections in managing hyperglycemia in Type 1 Diabetes, they fall short in addressing autoimmunity and regenerating damaged islets. This review aims to explore the potential of various treatment modalities for T1DM, including mesenchymal stem cells (MSCs), MSC-derived exosomes, gene therapy, islet allotransplantation, and pancreatic islet cell transplantation. Results: MSCs demonstrate efficacy in T1DM treatment through immunomodulation and tissue regeneration, although further research is warranted to optimize their therapeutic potential. Gene therapy presents a promising approach despite challenges such as donor shortage and immune rejection. Pancreatic islet cell transplantation emerges as a viable option, albeit with associated risks including graft rejection and the need for immunosuppression. Teplizumab, an FDA-approved humanized monoclonal antibody, revolutionizes the treatment landscape of Type 1 Diabetes by significantly delaying its onset, offering a paradigm shift since the discovery of insulin Conclusion: Ongoing studies and technological advancements in T1DM management offer a promising outlook for improved treatments and possibly even eradication on a global scale. MSCs, MSC-derived exosomes, gene therapy, and pancreatic islet transplantation hold considerable potential.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

Hypophthalmichthys nobilis are widely distributed in the Yangtze River basin and its related lakes. They are an important economic fish species and are a famous cultured species known as the "Four Famous Domestic Fishes" in China. Currently, with the fishing ban in the Yangtze River basin, fishing for H. nobilis in natural water bodies of the Yangtze River basin has been completely prohibited. In order to identify the sources of H. nobilis appearing in the market, further control and accountability, it is necessary to trace the sources of H. nobilis in the Yangtze River basin and its related water bodies. Therefore, this study identified and traced different sources of H. nobilis through muscle element fingerprint analysis (EFA). The results show that H. nobilis from different stations have characteristic element compositions. The characteristic element of H. nobilis from Wuhan (WH) is Pb, which is significantly higher than that in other stations; the characteristic element from Anqing (AQ) is Hg, which is significantly higher than that in other stations; and the characteristic element from Taihu (TH) is Al, which is significantly higher than that in other water areas. Multivariate analysis selected different spatial distribution patterns of 4 discriminant elements ratios (Pb/Ca, Cr/Ca, Na/Ca, Al/Ca) in the muscle of H. nobilis in the Yangtze River basin and its related lakes. The study suggests that the screened discriminative elements can be used to visually distinguish different sources of H. nobilis, and to quickly trace and verify the origin of newly emerging samples. Therefore, the use of selected discriminant element fingerprint features to trace the origin of new samples has been proven to be feasible. By further discriminating and verifying the muscle element fingerprints of new samples, the discrimination rate is high. Therefore, Multivariate analysis for muscle element fingerprint can be used for origin traceability of samples of unknown origin in market supervision.

A pivotal strategy in decarbonizing the transport sector is by transitioning from internal combustion engine vehicles (ICEVs) to electric vehicles (EVs), especially if they are charged with renewable energy. To provide an incentive to the common populace to switch to EVs, cities should set up - or enable or even encourage the private sector to do so - electric vehicle charging stations (EVCS) at multiple and suitably accessible locations. This paper aims to present a digitaltwin-enabled methodology study for selecting the most suitable possible locations to establish EVCS with consideration of the low voltage (LV) network operation in terms of power losses, active and reactive power in EV charging demand and the effect of the EVCS on the transformers, based on examples in Newcastle upon Tyne (England, UK). It also evaluates the most suitable type of charger that could be installed at these locations by studying the estimated traffic, cost and impact of the EVCS on the power grid, both at peak and off hours. This paper demonstrates how digitaltwin technologies, such as the web-based tool AutoDesign by Northern Powergrid and EA Technology and open source Pandapower can be used for identifying the most viable and cost-effective locations to connect EVCSs to a Distribution Network Operators (DNO)’s LV network. The results of the analysis indicate that with the installation of the most suitable type of EVCS in a particular location, the local power grid would not be significantly affected at any hour of the day.

Additives for anaerobic digestion (AD) can play a significant role in optimising the process by increasing biogas production, stabilising the system and improving digestate quality. The role of additives largely boils down to: (i) enhancing direct interspecies electron transfer (DIET) between microbial communities, resulting in improved syntrophic interactions and methane production rates (e.g. biochar, magnetite and carbon nanotubes), (ii) adsorption of toxic substances that may inhibit microbial activity (e.g. activated carbon, zeolites), (iii) improving microbial activity and increasing process stability (e.g. cobalt, nickel, iron, selenium), (iv) maintaining optimal pH levels for microbial activity (e.g. magnesium oxide), (v) reducing inhibition (the aforementioned adsorbents and conductive substances), (vi) accelerating the decomposition of complex organic materials into simpler compounds that are more easily digested by microorganisms, thereby increasing the rate of hydrolysis (enzymes, including cellulases, proteases and lipases). Through the aforementioned action, additives can significantly affect AD performance. The function of these materials varies, from enhancing microbial activity to maintaining optimal conditions and protecting the system from inhibitors. The choice of additives should be carefully tailored to the specific needs and conditions of the digester to maximise benefits and ensure sustainability. In light of these considerations, this paper characterizes the most commonly used additives and their combinations based on a comprehensive review of recent scientific publications, including a report on the results of conducted studies. The publication features chapters that describe: carbon-based conductive materials, metal oxide nanomaterials, trace metal and biological additives, including enzymes and microorganisms. It concludes with a chapter summarising reports on various additives and discussing their indications for functional systems with determined properties. A notable advantage of this work is the updated literature data, clear summaries, and a substantive description of the performance of the additives discussed.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

Background/aims: Prior research identified a significant association between heart disease and metabolic dysfunction-associated liver steatohepatitis (MASLD), but the mechanisms are unclear. This study aims to search predictive biomarkers for grade I left ventricular diastolic dysfunction (LVDD), an early stage of heart failure (HF), in type 2 diabetes mellitus (T2DM) patients. Methods: This single-center, prospective observational study screened 73 T2DM patients for grade 1 LVDD and MASLD using 2D echocardiography, tissue analysis, spectral color Doppler, and Fibromax. Results: The study analyzed 50 patients (mean age 58±11.3 years) with a median diabetes duration of 7 years, abdominal obesity (mean BMI 34.4±5.9 kg/m2), and a mean HbA1c of 7.9±1.5%. The prevalence of grade I LVDD, fibrosis, mild steatosis, moderate to severe liver steatosis, mild MASLD, and moderate MASLD was 54%, 44%, 14%, 80%, 43%, and 34%, respectively. Regression analysis revealed that grade 1 LVDD was positively associated with age, Fibrotest, ɑ2-macroglobulin, epicardiac adipose tissue (EAT), and negatively associated with lateral s`, E wave, E/e`, E/A, medium E`, and septal e` (p< 0.05 for all). ɑ2-macroglobulin > 1.92 g/L (AUROC= 0.782, sensitivity 70.4%, specificity 81.2%) and fibrotest score > 0.11 (AUROC 0.766, sensitivity 92.6%, specificity 56.2%) were significant predictors of grade I LVDD. Conclusion: HF is a multifaceted disorder associated with multisystem organ damage, including nonalcoholic MASLD. Although the underlying mechanisms remain unclear, innovative non-invasive biomarkers, such as ɑ2-macroglobulin or fibrotest, could concurrently indicate liver stiffness and the likelihood of grade I LVDD, an early, asymptomatic HF stage in T2DM patients.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Microbial composition across substrates in mangroves, particularly in the Middle East, remains unclear. This study characterized bacterial communities in sediment, water, Terebralia palustris snail guts, and plastic associated with Avicennia marina mangrove forests in two coastal lagoons in the Sea of Oman using 16S rDNA gene MiSeq sequencing. The genus Vibrio dominated all substrates except water, which featured unique genera Sunxiuqinia and Pseudomonas. There were significant differences in bacterial communities on different substrata, in particular plastic. Snail guts harbored the highest number of unique Operational Taxonomic Units (OTUs) in both lagoons. Plastic in the polluted Sawadi lagoon with low salinity harbored distinct genera like Vibrio, Aestuariibacter, Zunongwangia, and Jeotgalibacillus absent in Qurum lagoon with higher salinity and low pollution. Sawadi lagoon exhibited higher species diversity in sediment and plastic substrates, Qurum lagoon demonstrated lower overall species diversity. The PCA indicates that environmental factors like salinity, pH, and nutrient levels significantly influence bacterial community composition across substrates. Variations in organic matter and potential anthropogenic influences, particularly from plastics, further shape bacterial communities. This study highlights the complex microbial communities in mangrove ecosystems, emphasizing the importance of considering multiple substrates in mangrove microbial ecology studies.

Despite the recent availability of immune checkpoint inhibitors, not all patients affected by Non-Small Cell Lung Cancer (NSCLC) benefit from immunotherapy. The reason for this variability relies to a variety of factors which may allow the identification of novel biomarkers. Presently, a variety of biomarkers are under investigation, including the PD1/PDL1 axis, the tumor mutational burden, and the Microbiota. This latter is made by all bacteria and other microorganisms hosted in our body. The gut microbiota is the most represented and has been involved in different physiological and pathological events, including cancer. In this light, it appears that all conditions modifying gut microbiota can influence cancer, its treatment, and its treatment-related toxicities. The aim of this review is to analyze all conditions influencing the gut microbiota and, therefore, affecting response to immunotherapy, iRAEs and their management in NSCLC patients. The investigation of the landscape of these biological events can allow novel insights for optimal management of NSCLC immunotherapy.

Spinocerebellar ataxia type 3 is a neurodegenerative disease caused by an abnormal expansion of CAG repeats in the disease gene ATXN3, leading to prolonged polyglutamine (polyQ) tracts in the respective protein ataxin-3. The polyQ-expanded protein forms polyQ-containing aggregates in several brain regions which leads to neuronal cell loss. Autophagy is thought to play a significant role in clearing these polyQ-containing protein aggregates. Therefore, the autophagy mechanism was investigated in SCA3 with focus on the autophagic protein p62/sequestosome-1. Human and mouse RNA sequencing data were analyzed to determine RNA expression level of autophagic genes. Additionally, autophagy was studied in the SCA3 304Q knock-in mouse model and through several cell culture experiments using HEK-293T cells transfected with ATXN3 of differ-ent polyQ lengths. For cell culture experiments, autophagy was induced with rapamycin treat-ment, proteasomal degradation was blocked with MG132 and degradation of autophagic pro-teins was investigated using cycloheximide treatment. Here, we report an increased autophagy impairment with SCA3 disease progression seen in HEK-293T cells transfected with ATXN3 plasmid with expanded polyQ tracts, higher aged 304Q-knock-in mice, or human post-mortem brain material. Furthermore, co-localized aggregation of the autophagic protein p62 and the dis-ease protein ATXN3 was observed in the course of SCA3 disease. Therefore, we suggest a signifi-cant role for p62 in aggregate formation seen in the neurodegenerative disease SCA3.

Primary Ciliary Dyskinesia (PCD) is a rare genetic disorder characterized by alterations in motile cilia func-tion. The diagnosis of PCD is challenging due to the lack of standardized methods in clinical practice. High-speed video microscopy analysis (HSVA) directly evaluates ciliary beat frequency (CBF) in PCD. Recently, open-source ciliary analysis software applications have shown promise in measuring CBF accurately. How-ever, there is limited knowledge about the performance of different software applications, creating a gap in understanding their comparative effectiveness in measuring CBF in PCD. We compared two open-source software applications, CiliarMove and Cilialyzer, against the manual count method. We used videos rec-orded at high-speed of nasal ciliary brush samples from PCD patients and healthy controls. All three meth-ods showed lower median CBF values in PCD patients than healthy controls. CiliarMove and Cilialyzer identified lower CBF in PCD patients, similar to the manual count. Cilialyzer, CiliarMove and manual count demonstrated statistical significance (p-value < 0.0001) in the difference of median CBF values be-tween PCD and healthy controls. These findings support the utility of open-source software-based analysis tools. Further studies are needed to validate these findings with other genetic variants and identify the op-timal software for accurate CBF measurement in PCD.

Background and Objectives Neurofibromatosis 1 (NF1 MIM # 162200), also known as von Recklinghausen disease, is among the most common autosomal dominantly transmitted disorders characterized mainly by neurocutaneous manifestations such as café au lait spots, intertriginous freckling, various types of neurofibromas (cutaneous neurofibromas or plexiform tumors), neurological manifestations, and bone abnormalities. It occurs with an incidence of 1:3000–1:4000 cases. Cone-rod dystrophies belong to the large group of retinal dystrophies, a highly heterogeneous group of disorders clinically manifested mainly by damage to cone and rod cells and have a broad spectrum of clinical manifestations. Many genes are involved in their etiology, with more than 100 currently identified, including the CRX gene responsible for the autosomal dominant form of cone-rod dystrophy (ad CORD). Materials and Methods: The authors present an intriguing case of a patient diagnosed with Neurofibromatosis type 1 (NF1) as an infant and ocular involvement (myopia and astigmatism onset at age 15), which yielded a surprising molecular testing result. Results: Molecular DNA analysis identified a rare occurrence of two mutational variants, including a pathogenic variant in the NF1 gene, c.3871-2A, and a likely pathogenic variant in the CRX gene c.119G>A. Conclusions: The authors present this case to highlight the surprises offered by molecular testing in a condition where the diagnosis is usually based on clinical criteria, thus providing patients with competent genetic advice.

The escalation of mining activities in the karst regions of Guizhou Province has heightened the occurrence of water-inrush incidents in deep coal mines. This study focused on water-inrush phenomena within the Xinhua mining area of Jinsha County, Guizhou Province, aiming to investigate the sources of these incidents. The findings indicated that the overlying limestone of the Changxing Formation in the coal seam served as a vulnerable aquifer under certain conditions, leading to water inrushes. The analysis of the spatiotemporal distribution patterns of water-inrush incidents at the working face indicated that previous mining operations damaged the shallow Changxing Formation limestone, resulting in the accumulation of goaf water and the formation of numerous mining-induced fractures. These fractures served as rapid conduits for water inrushes from both atmospheric precipitation and underground sources at the deep working face. The examination of surface water and mine water quality demonstrated that both exhibited similar characteristics, predominantly featuring bicarbonate, sulfate, and sodium compositions. Investigation into the relationship between mine water inflow and atmospheric precipitation established that atmospheric precipitation influenced the mine water supply cycle, with a replenishment period of ~10 months during the operational phase of the Jinyuan Coal Mine and about one month post-closure. The fractures induced by mining activities within the Changxing Formation limestone facilitated water flow, with atmospheric precipitation serving as the primary water source for the mine. This study offered a valuable scientific foundation for addressing water-related damage resulting from atmospheric precipitation in mines susceptible to water inrushes under analogous hydrogeological conditions.

This paper designs and fabricates a small-type permanent-magnet linear motor and driver for automation applications. It covers structural design, magnetic circuit analysis, control strategies, and hardware development. Magnetic circuit analysis software JMAG is used for flux density distribution, back electromotive force(back-EMF), and electromagnetic force analysis. To address end effects and cogging force, auxiliary core structures and control strategies are proposed. The motor has a three-phase, six-coil, seven-pole configuration, achieving a peak phase voltage of 3.621 V at 1.0 m/s with a total harmonic distortion(THD) of 0.49 % and the voltages of each phase are balancing a phase voltage error of -0.002 V. The average electromagnetic force is 5.46 N/A. The driver uses a three-phase inverter with voltage space vector pulse width modulation(VSVPWM), dq-axes current closed-loop control, electromagnetic force control, and S-curve motion trajectory control. Simulations with JMAG-RT models in MATLAB/Simulink verify the control strategies. A microcontroller (TMS320F280045) serves as the control core, and a magnetic encoder with a 488 nm resolution provides position feedback. Each phase winding has an equivalent resistance of approximately 3.0 Ω and an inductance of approximately 1.98 mH. The S-curve motion trajectory control achieves a maximum position error of approximately 5.0 μm and a speed ripple of approximately 0.03 m/s at steady speed. With cogging force improvement, the maximum electromagnetic force is 4.90 N, and the q-axis current compensates around 1.05 A based on mover position. S-curve motion trajectory control results in highly stable and responsive performance. Practical tests show that the designed small-type permanent-magnet linear motor and its driver provide efficient, stable, and high-precision solutions for automation applications.

In this paper, we have established Hermite-Hadamard inequalities for r-preinvex functions via fractional integrals.

Motivated by empirical observations, we propose a possible extension of Gibrat's law. By applying it into the random growth theory of income distribution (Gabaix, 2009), we find that the income distribution is described by a generalized Pareto-type distribution (GPD) with three parameters. We observe that there is a parameter /elta in the GPD that plays a key role in determining the shape of income distribution. By using the Kolmogorov-Smirnov test, we empirically show that, for typical market-economy countries, /elta is close to 0 significantly, such that the income distribution is characterized by a two-class pattern in which the bottom 90% of the population is approximated by an exponential distribution and the richest 1%~3% is approximated by an asymptotic power law. However, we empirically find that, for China both in planned economy period and in early stages of market reformation (from 1978 to 1990), /elta is significantly deviated from 0, such that the bottom of the population no longer conforms to an exponential distribution.

The incidence of diabetes mellitus (DM) continues to rise worldwide and one of the most serious microvascular complications is diabetic kidney disease (DKD), which is the leading cause of end-stage renal disease. Current bi-omarkers such as urinary albumin excretion rate have limitation for early detection of DKD. In our study we used ultra-high-performance liquid chromatography coupled with electrospray ionization-quadrupole-time of flight-mass spectrometry (UHPLC-QTOF-ESI+-MS) techniques to quantify previously analyzed metabolites, such as tryptophan, kynurenic acid, taurine, l-acetylcarnitine, glycine, and tiglylglycine. We performed the targeted analy-sis of metabolites from urine and serum samples, collected from 110 subjects. Of these, 90 patients with type 2 DM (T2DM) were divided according to the urinary albumin/creatinine ratio (UACR) into normoalbuminuria 300 mg/g groups, respectively, while 20 subjects were rep-resented by healthy controls. Through various validation methods, we identified several metabolites as potential biomarkers, such as kynurenic acid, glycine, and l-tryptophan in serum and l-acetylcarnitine, tiglylglycine, and tau-rine in urine.

Type 2 diabetes mellitus (T2DM), a multifactorial and complicated metabolic disorder, is a growing public health problems. Numerous studies indicated that bioactive compounds from herbal medicine have beneficial effects on T2DM prevention and treatment, owing to their numerous biological properties. Curcumin, the major curcuminoid of turmeric, is one of the most studied bioactive components of herbal supplements, which has a variety of biological activities. Clinical trials and preclinical research have recently produced compelling data to demonstrate the crucial functions of curcumin against T2DM via several routes. Accordingly, this review systematically summarizes the antidiabetic activity of curcumin, along with various mechanisms. Results showed that effectiveness of curcumin on T2DM is due to it being anti-inflammatory, anti-oxidant, anti-hyperglycemic, anti-apoptotic, anti-hyperlipidemia and other activities. In light of these results, curcumin may be a promising prevention/treatment choice for T2DM.

In this paper, we establish the generalized Qi-type inequality involving conformable fractional integrals. The results presented here would provide extensions of those given in earlier works.

This paper is devoted to the study of multi-dimensional integral transform with Fox H-function in the kernel in weighted spaces integrable functions in the domain R+n with positive coordinates. Mapping properties such as the boundedness, the range, the representations of the considered transformation are established.

To assess the community health workers’ (CHWs) knowledge, attitude, and practices (KAP) in type-2 diabetes (T2D) and hypertension (HTN) management. We thus also sought to assess the potential health system barriers for incorporating CHWs in T2D and HTN management. Mixed-method study comprised (1) a survey among 153 active CHWs to assess their KAP of T2D and HTN, and (2) semi-structured interviews with key informants to understand challenges of the health system and proposed solutions in incorporating CHWs in T2D and HTN management. The majority of CHWs correctly answered general knowledge questions on NCDs, risk factors, and prevention; however, only one-quarter correctly answered questions on smoking, family history, or tobacco use as risk factors. Most respondents appeared to have positive attitudes and have been practicing some activities related to T2D and HTN. Both financial and non-financial resource constraints were cited as challenges of the health system; therefore, re-structuring the role definition of CHWs and task of responsibilities, and assessment the need and workload have been proposed as ways forwards to effectively incorporate CHWs in T2D and HTN care. CHWs in Cambodia have shown their potential in T2D and HTN management; however, a well-designed strategy including technical training, clearly defined roles and responsibilities, and strong supporting structure are important to maximize their potential in the health system.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Multidrug resistant organisms (MDROs) outbreaks have been steadilyincreasing in Intensive care units (ICUs). Still, healthcare institutions and workers (HCW) reached no unanimity on how and when implementing infection prevention and control (IPC) strategies. We aimed to provide a pragmatic, physician practice-oriented, resume of strategies towards different MRDOs outbreaks in ICU. We performed a narrative review on IPC in ICUs, investigating patient-to-staff ratios, education, isolation, decolonization, screening and hygiene practices, outbreak reporting, cost-effectiveness, reproduction-number(R0), and future perspectives. The most effective IPC strategy remains unknown. Most studies focus on a specific pathogen or disease, making the clinician losing the big picture. IPC strategies proved their cost-effectiveness regardless typology, country, or pathogen. A standardized, universal, pragmatic protocol for HCW education should be elaborated. Likewise, a rapid outbreak recognition tool elaboration (i.e., an easy-to-use mathematical model) would improve early diagnosis and spreading prevention. Further studies are needed to express in favor or against MDROs decolonization. New promising strategies are emerging and need to be tested in the field. The lack of IPC strategies application has made, and still makes ICUs a major MDROs reservoir into the community. In a not-too-distant future genetic engineering and phage therapies could represent a plot-twist in MDROs IPC strategies.

Objective: Subclinical left ventricular disfunction (LVD) is common in asymptomatic patients with type 2 diabetes (T2D). Many patients with diabetes have an impaired diastolic and systolic function. With preserved ejection fraction LV (EFLV), the latter is defined as reduced global longitudinal strain (GLS), detected using the speckle-tracking echocardiography. This study is aimed to define the long-term structural and functional disorders of the LV myocardium in patients with T2D without CVD. Methods: Of the 120 patients with and without T2D of both sexes aged from 45 to 75 years (57.11±7.9 years), included in the study in 2012-2013, only 57 responded to the follow-up study. The patients were divided into two groups: one with T2D (n=29), the other without it, control (n=28). All patients underwent transthoracic two-dimensional echocardiography with assessment of standard indicators of systolic and diastolic cardiac function, as well as GLS. In addition, all participants underwent laboratory diagnostics of carbohydrate metabolism disorders markers, NT-proBNP and CRP. The median follow-up duration was 7.2 [7.0-7.8] years. Results: During the follow-up, a statistically significant increase in the incidence of diastolic dysfunction (DD) in the type 2 diabetes group was found from 53% to 61% (p = 0.004); no significant dynamics were noted in the control group (p = 0.48). The presence of T2D significantly increases the risk of developing DD (p=0.04). The presence of T2D, increased fasting glucose levels, and an increased HOMA index were independent predictors of the development of DD. Impairment of LVEF was not observed in both groups. At the same time, the proportion of patients with reduced GLS (< -18%) increased in the T2D group (p = 0.036). A significant difference in the frequency of decreased GLS depending on T2D was demonstrated. The presence of obesity, an increase in the HOMA index and an increase in CRP levels are independent predictors of impaired GLS. Conclusions: T2D is an independent risk factor for the worsening of subclinical left ventricular dysfunction in asymptomatic patients with T2D without CVD over 7-year follow-up. Diastolic dysfunction is represented by delayed relaxation of the LV myocardium; with preserved LVEF, reduced 2D GLS identifies systolic dysfunction. The tight control of glycemia, lipidemia, blood pressure and body weight is associated with the absence of poor clinical outcomes.

The rapid urbanization in China has significantly contributed to the vast expansion of urban built-up areas. Precisely extracting and monitoring these areas is crucial for understanding and optimizing the developmental process and spatial attributes of smart, compact cities. However, most existing studies tend to focus narrowly on a single city or global scale with a single dimension, often ignoring mesoscale analysis across multiple urban agglomerations. In contrast, our study employs GIS and image processing techniques to integrate multi-source data for the identification of built-up areas. We specifically compare and analyze two representative urban agglomerations in China: the Yangtze River Delta (YRD) in the east and the Chengdu-Chongqing (CC) region in the west. We use different methods to extract built-up areas from socio-economic factors, natural surfaces, and traffic network dimensions. Additionally, we utilize a high-precision built-up area dataset of China as a reference for verification and comparison. Our findings reveal several significant insights: (1) The multi-source data fusion approach effectively enhances the extraction of built-up areas within urban agglomerations, achieving higher accuracy than previously employed methods. (2) Our research methodology performs particularly well in the CC urban agglomeration. The average precision rate in CC is 96.03%, while the average precision rate in YRD is lower at 80.33%. This study provides an objective and accurate assessment of distribution characteristics and internal spatial structure of built-up areas within urban agglomerations. This method offers a new perspective for identifying and monitoring built-up areas in Chinese urban agglomerations.

Background: Extra virgin olive oil is a fundamental component of the Mediterranean diet. It contains several molecules that sustain human well-being by modulating cellular metabolism and exerting antioxidant, anti-inflammatory, anti-ageing effects to protect normal tissues and can exert anti-angiogenic, and pro-apoptotic effects on cancer cells. Metabolites found in different parts of the olive tree, including leaves, also possess properties that might help in cancer prevention and promote wellness in aging. Olive mill wastewater (OMWW), a liquid residue produced during olive oil extraction, represents an environmental issue. However, it is enriched in phytochemicals with potential beneficial properties. Dietary supplements based on OMWW can be produced for nutritional supplementation with advantages to the ecology. Purpose: This work aims to measure hematochemical, anthropometric and metabolomic parameters in volunteers assuming an OMWW dietary supplement, OliphenoliaⓇ (OMWW-OL). Methods: The supplementation of OMWW-OL 25 mL twice daily for 30 days was tested on a pilot cohort of volunteers with characteristics close to metabolic syndrome. Hematochemical, anthropometric, and metabolomic parameters were analyzed before the intervention, at 30 days and 30 days after stopping consumption. Results: 29 volunteers were enrolled and 23 completed the study. The participants’ parameters at baseline were measured, and then twice daily at 30 days of treatment and 30 days after assumption discontinuation. Although treatment was with an olive derivative, weight and body mass index instead of increasing slightly decreased, particularly in women. Also, hydration increased, especially in women, while blood pressure, glycemia and insulin decreased. Cholesterol, low-density and high-density lipoproteins and triglycerides were stable while vitamin D levels, alongside calcium, sensibly increased. Albumin also increased and parameters related to sarcopenia displayed promising, although not statistically significant, trends toward positive effects. All the values were in support of an equilibrium with no damaging effects. By mass spectrometry analysis, we also found favorable changes in the vitamin D/histamine and homocysteine/methionine ratios, an increase in a new metabolite of unknown formula, and vitamin D/unknown metabolite ratio. Conclusions: Supplementation of OMWW-OL has no detrimental effects and, although with limited potency of a pilot study, might imply the beneficial modulation of several biological parameters, being potentially valuable for people at risk of metabolic syndrome. Some of these parameters could also be relevant as anti-ageing and in cancer prevention.

Dry Fish is a rich source of proteins and nutrients and can be eaten in many forms. Oman is one of the important fish producers in the world and having high demand in neighboring countries for Oman’s fish. Fishery sector is considered as one of the important economic development sector in sultanate of Oman. In the fishery sector, use of technology is not up to the mark because of less awareness of technology application among Omani fishermen. Also, there is a demand for a greater number of cold storages in different regions to store fresh fishes which is not materialized yet. Similarly, there is a demand of perfect and cheap technology in Oman to dry fishes to improve the profit to the fishermen. Solar energy is abundantly available in Oman and there are high possibilities in Oman to use solar energy in domestic and industrial applications. Since the sunlight is available throughout the year, it is possible to convert in to thermal energy or electrical energy. Electricity can be produced from photovoltaic principle (PV) or indirectly with concentrated solar power. Similarly, we can use solar concentrators for many thermal applications. The solar dryer is a device which is used to dry fruits, vegetables, leaves, clothes etc. If any of the items are dried with the help of solar energy, then we can save lot of non-renewable source of energy and can help to improve economy of the country. The sun can, at least seasonally at Oman’s latitudes, provide a substantial part of the energy needed for various applications. In this work, we used solar dryer to make dry fish with high quality. Use of parabolic type concentrator to dry the fish is an effective solution which is an innovative idea to the fishermen. The temperature variation in dryer is directly proportional to the intensity of solar. The tracking mechanism is a combination of electronic and mechanical design which tracks the sun automatically. In this work, a parabolic concentrator with automatic tracking mechanism was designed and the performance analysis have been done. In the design, copper tubes are used for heat transfer and then the hot fluid is circulated in the box which is used to dry the fishes. As per the experiment, fish drying efficiency obtained from solar dryer is 77.9% and it took 3 days to dry king fish of 20kg. There are many advantages in parabolic type solar concentrators relate to the quality of dryness in the fishes and time taken to dry the fishes which are elaborately discussed in this paper. This solar dryer technology will improve green environment and also will save non-renewable sources of sultanate of Oman for longer period of time.

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Background and Objectives: In this current state, Type 2 Diabetes Mellitus (T2DM) is more prevalent in the population, and metformin is used as a first-line medication for treating it. There was up surge in the utilization of alternative therapies in the management of diabetes. Especially in diabetes, Herbal medicines are considered safe and reliable by majority of the population. Aim: The purpose of this research is aimed to estimate the safety and efficacy of Polyherbal Metabolite Compounds (PHMC) capsules in adults with T2DM. Materials and Methods: In this study, 60 T2DM patients aged 18-60 years were randomly assigned to Groups A (30) receiving Metformin 500 mg twice a day after food and Group B (30) receiving PHMC capsule 500 mg twice a day after food in a prospective, randomized and open-label clinical study. The in-silico simulation study was performed to selected plants major compounds on target protein Insulin-like Growth Factor-1 (1K3A). Result: The PHMC is found to be safe and effective in the management of T2DM. The FBS, PPBS and HbA1c were significantly lowered (p

Background/Objectives: Periodontitis (P), a chronic inflammatory condition that affects the supportive tissues around the teeth, is 3 to 4 times more prevalent in individuals with diabetes mellitus (DM), with a direct correlation between its severity and the levels of glycosylated haemoglobin (HbA1c). This study aimed to evaluate the periodontal clinical parameters following non-surgical periodontal treatment (NSPT) in patients with and without type 2 DM and P. Methods: Forty patients with P were divided into two groups: Group DM/P and Group P. All patients were assessed at baseline, and 90 and 180 days after receiving NSPT. The parameters evaluated included HbA1c levels, plaque index (PI), probing pocket depth (PPD), clinical attachment level (CAL), and bleeding on probing (BoP). Statistical analysis was performed with a significance level set at α = 5%. Results: There were significant differences in HbA1c levels between the DM/P and P groups at baseline, 90, and 180 days, as expected. Importantly, HbA1c levels did not change after NSPT. Group P showed a significant reduction in both PI and BoP values at 90 and 180 days (p &lt; 0.05). In contrast, group DM/P demonstrated a significant increase in the percentage of sites with PPD ≥ 5mm at 180 days (p &lt; 0.05). Additionally, group P exhibited an increase in sites with PPD ≤ 4mm and a decrease in sites with PPD ≥ 5mm at both 90 and 180 days (p &lt; 0.05). Conclusions: Our findings suggest that DM may compromise the effectiveness of NSPT, potentially hindering favorable outcomes during the follow-up period.

Background/Objectives: The global burden of metabolic dysfunction-associated steatotic liver disease (MASLD) is increasing at an alarming rate. Cardiovascular disease (CVD) is the leading cause of mortality in MASLD patients, therefore, the therapeutic interventions for MASLD should improve coronary risk factors such as obesity, diabetes and dyslipidemia, in addition to improving liver function. The evidence on effect of sodium-glucose cotransporter 2 inhibitors (SGLT2is) which have beneficial pharmacological properties for MASLD, especially the long-term effects, on the progression of MASLD in Asian population is very limited. Methods: The retrospective longitudinal study was performed by using the medical records at the National Center for Global Health and Medicine, Kohnodai Hospital, Japan. We picked up patients with type 2 diabetes who had taken SGLT2is for at least 3 years or longer between April 1, 2014 and March 31, 2018. We collected the data on metabolic parameters, including blood tests and anthropometric parameters, and compared the data before and after the initiation of SGLT2is treatment. Results: During the observation period, 324 patients had taken SGLT2is for 3 years. The 3-year-SGLT2is treatment significantly reduced body weight, hemoglobin A1c, low-density lipoprotein-cholesterol, triglyceride and non-high-density lipoprotein-cholesterol (HDL-C) and significantly increased HDL-C. Furthermore, this treatment significantly improved liver function and the markers for hepatic steatosis and hepatic fibrosis. Conclusions: Considering that the development of CVD determines the prognosis of MASLD patients, the long-term SGLT2is treatment may be an ideal therapy for MASLD patients.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&amp;O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&amp;O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

Background and Objectives: Cancer as the second leading cause of death in the United States poses a huge healthcare burden. Barriers to access to advanced therapies influence the outcome of cancer treatment. In this study, we examined whether insurance types affect the quality of cancer clinical care regarding access to an important monoclonal antibody, ramucirumab. Materials and Methods: Data for 13,340 cancer patients with Purchased or Medicaid insurance from the All of Us Database were collected for this study. The Chi-square test of proportions was employed to determine the significance of patient cohort characteristics and ramucirumab usage between Purchased and Medicaid insurance groups. The independent t-test was utilized to assess the influences of other determinants on insurance types. Results: Cancer patients who are African American, with lower socioeconomic status, or with lower educational attainment are more likely to be insured by Medicaid. Analysis of survey questions demonstrated the relationship between income and education level with insurance type as Medicaid cancer patients were less likely to receive primary care and specialist physician access and more likely to request lower cost medications. In addition, those with Medicaid insurance were identified to have poorer access to expensive therapeutics like ramucirumab compared to those with Purchased insurance.  Conclusions: The inequities of the US healthcare system are observed for cancer patient care; access to physicians and therapeutics are highly varied and dependent on insurance types. Socioeconomic status determines insurance type, which unfortunately generates a significant impact on cancer treatment and disease outcome.

The comorbidity of osteoarthritis and type 2 diabetes mellitus represents a complex clinical challenge and complicates patient management due to the interplay of overlapping pathophysiological mechanisms. The research aimed to analyze the exacerbation of clinical symptoms and biochemical markers in patients with osteoarthritis and type 2 diabetes mellitus compared to those with osteoarthritis. We utilized various assessment methods to measure the patient cohorts' inflammation, oxidative stress, and glycemic control. The study also involved the administration of alpha-lipoic acid to patients with comorbid osteoarthritis and type 2 diabetes mellitus and monitored its effects on joint function, inflammatory markers, oxidative stress levels, and glycemic control. Our findings revealed that the presence of type 2 diabetes mellitus significantly intensified osteoarthritis symptoms and altered biochemical markers, including increased inflammation, elevated oxidative stress, and disrupted immunological balance. The treatment with alpha-lipoic acid resulted in improved joint function, reduced inflammation and oxidative stress levels, and better glycemic control. Additionally, it was identified several potential predictors for developing osteoarthritis and type 2 diabetes mellitus comorbidity. The results underscore the detrimental impact of type 2 diabetes mellitus on osteoarthritis and highlight the beneficial effects of alpha-lipoic acid in alleviating some of the adverse consequences associated with this comorbidity. Nonetheless, further research is necessary to comprehensively evaluate the therapeutic efficacy of alpha-lipoic acid and its long-term effects on managing comorbidity of osteoarthritis and type 2 diabetes mellitus.

Sediment plumes, released to the Bering Sea from the delta front of the Yukon River, Alaska, are initiated mainly by glacier-melt sediment runoffs in the glacierized regions of the Yukon River drainage basin. The surface sediment plumes are extended around the fan-shaped Yukon River delta, which is followed by the northwestward dispersion. During continuous measure-ments of the Yukon River discharge and sediment load, behaviors of the sediment plumes were explored by shipboard observations in the Bering Sea offshore from the Yukon delta. At the high river sediment load of ca. 3000 kg/s, the plume partially plunged into the sea bottom layer. The plunging probably originated in the nepheloid-layer formation from the flocculation of river-suspended sediment, of which more than 90 %wt. is silt and clay (grain size d < 0.063 mm). In order to numerically obtain the area of the surface sediment plumes, a satellite image analy-sis was performed by using three near-infrared bands in MODIS/Aqua or MODIS/Terra. The plume area was significantly correlated (R2=0.735, p<0.01) to the sediment load averaged for the two days with time lags of 20 days and 21 days to the date of a certain satellite image. Hence, the dispersion of plume-suspended sediment appears to be controlled by the sediment runoff events in the Yukon River rather than the northward “Alaskan Coastal Water”.

Selenium nanoparticles (SeNPs) can mitigate cadmium (Cd2+) toxicity in crop cultivation and aquaculture. This study investigates the impact of SeNPs on Cd-induced toxicity in Chlamydomonas reinhardtii, a model organism, aiming to mitigate Cd damage in crops. SeNPs were synthesized using sodium carboxymethyl cellulose (CMC) as a dispersant and vitamin C to reduce H2SeO3. Characterization by transmission electron microscopy (TEM) and nanoparticle granulator revealed uniform, stable spherical SeNPs. Cd2+ and SeNPs of varying concentrations were introduced into culture media of wild type (CC125mt+) and cell wall defect type (CC400mt+) Chlamydomonas reinhardtii. Growth curves, photosynthetic pigment content, enzyme activities (T-SOD and CAT), MDA content, and ROS levels were assessed. Fluorescence induction kinetics, QA oxidation kinetics, and Cd2+ content in cells were measured to evaluate SeNPs' effect on Cd toxicity. Results showed SeNPs exacerbated Cd2+ toxicity in CC125mt+ by inhibiting growth and increasing catalase activity, indicating enhanced oxidative damage. SeNPs intensified PSII damage by Cd2+ and increased intracellular Cd2+ content, possibly exacerbating toxicity. SeNPs had no effect on Cd2+ toxicity in CC400mt+. Overall, SeNPs exacerbated Cd2+ toxicity in wild type CC125mt+ but not in cell wall defective CC400mt+. These findings caution against indiscriminate use of nano-selenium to mitigate Cd damage, stressing the importance of careful target selection, dosage, and range considerations.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

Background: Study to assess glucose levels of people with type 1 diabetes (T1D) overnight based on insulin type and timing. Methods: Real-world, retrospective study in T1D using multiple daily insulin injections. Contin-uous glucose monitoring and insulin injections data were collected for ten hours after dinner us-ing the Insulclock® connected cap. Meal events were identified using ROC detection methodology. The timing of rapid insulin, second injections, and the type of insulin analogs used were evaluat-ed. Results: Nocturnal profiles (n=775, 49 subjects) were analyzed. Higher glucose AUC over 180mg/dL was observed in delayed injections (number; %; mg/dL x h): -45-15min (n=136; 17.5%, 175.9 ±271.0); -15-0min (n= 231; 29.8%, 164.0 ±237.1); 0+45min (n= 408; 52.6%, 203.6 ±260.9), (p 0.049). The use of ultrarapid (FiAsp®) (URI) vs rapid insulin analogs (RI) was associated with less hypoglycemia events (7.1 vs 13.6%; p 0.005) and TBR70 (1.7 +6.9 vs 4.6 +13.9%; p 0.003). Us-ers of glargine U300 vs degludec had higher TIR (70.7 vs 58.5 %) (Adjusted R-squared: 0.22, p < 0.001). The use of a correction injection (n= 144, 18.6%) was associated with higher hypoglycemia events (18.1 vs 9.5%; p 0.003), TBR70 (5.5 +14.2 vs 3.0 +11.1%; p 0.003), glucose AUC over 180 mg/dL (226.1 +257.8 vs 178.0 +255.3 mg/dL x h; p 0.001), and lower TIR (56.0 +27.4 vs 62.7 +29.6 mg/dL x h; p 0.004). Conclusions: Dinner rapid insulin timing, insulin types and correction injections affect nocturnal glucose profile in T1D.

Collagen is the most abundant protein in the animal kingdom. Industrial collagen is mainly bovine and porcine origin. However, due to religious beliefs, allergic issues, and infectious diseases, alternative sources of collagen as marine are gaining increasing interest. In this work, the acid-soluble collagen (ASC) were extracted from salt-cured Atlantic cod (Gadus morhua) skin and characterized. The extraction yield was about 2.0%, equivalent to the extraction yield reported for other fish skins. The electrophoretic pattern showed the typical type I structure (α, β and γ chains). UV-VIS and FTIR absorbance spectra suggested a very pure ASC with an intact triple helical structure. The integrity and the adequate porosity required for different applications were then confirmed by electron micrograph. Our findings allow us to say that, for the first time, we extracted acid-soluble type I collagen from salt-cured Atlantic cod skin, with characteristics suitable for application in various fields, such as biomedical.

Protein tyrosine phosphatase receptor type E (PTPRE) is a member of the “classical” protein tyrosine phosphatase subfamily and regulates a variety of cellular processes in a tissue-specific manner by antagonizing the function of protein tyrosine kinases. PTPRE plays a tumorigenic role in different human cancer cells, but its role in retinoblastoma (RB), the most common malignant eye cancer in children, remains to be elucidated. Etoposide resistant RB cell lines and RB patients display significant higher PTPRE expression levels compared to chemosensitive counterparts and the healthy human retina, respectively. PTPRE promotor methylation analyses revealed that PTPRE expression in RB is not regulated via this mechanism. Lentiviral PTPRE knockdown (KD) induced a significant decrease in growth kinetics, cell viability, and anchorage independent growth of etoposide resistant Y79 and WERI RB cells. Caspase-dependent apoptosis rates were significantly increased and a re-sensitization for etoposide could be observed after PTPRE depletion. In vivo chicken chorioallantoic membrane (CAM) assays revealed decreased tumor formation capacity as well as reduced tumor size and weight following PTPRE KD. Expression levels of miR631 were significantly downregulated in etoposide resistant RB cells and patients. Transient miR631 overexpression resulted in significantly decreased PTPRE levels and concomitantly decreased proliferation and increased apoptosis levels in etoposide resistant RB cells, impacts mirroring PTPRE KD effects and indicating PTPRE regulation via this miR. Additionally, PTPRE KD led to altered phosphorylation of protein kinase SGK3 and - dependent on the cell line - also AKT and ERK1/2, suggesting potential PTPRE downstream signaling pathways. In summary, these results indicate an oncogenic role of PTPRE in chemoresistant retinoblastoma.

As an active device, air source heat pumps (ASHP) are widely used for heating and cooling in buildings. However, in cold regions, their efficiency decreases, and frost formation becomes a significant issue during winter. This paper proposes a new scheme that couples air source heat pumps with passive heating. By using software simulations and mathematical models, the new scheme is compared to traditional ASHP systems to analyze its heating performance in rural homes during winter in China’s cold regions. According to the simulation and calculation analysis, on the coldest day of winter, the coupling scheme can provide approximately 99.41kWh of heat to the interior, surpassing the 86.67kWh required to maintain an indoor temperature of 20℃. The system’s power consumption is 36.96 kWh, which is 66.88% lower than that of traditional heat pump heating. The study shows that a coupled system of air source heat pumps and passive heating has better heating performance in cold regions. By incorporating phase change materials and heat storage media to address the shortage of solar energy at night, the system can meet the heating needs throughout the entire day.

Background: Smad4, a critical tumor suppressor gene, plays a significant role in pancreatic biology and tumorigenesis. Genetic background and sex are known to influence phenotypic outcomes, but their impact on pancreatic weight in Smad4-deficient mice remains unclear. This study investigates the impact of Smad4 deficiency on pancreatic weight in F1 mice from diverse Collaborative Cross (CC) lines, focusing on the influence of genetic background and sex. Methods: F1 mice were generated by crossbreeding female CC mice with C57BL/6J-Smad4tm1Mak males. Genotyping confirmed the presence of Smad4 knockout alleles. Mice were housed under standard conditions, euthanized at 80 weeks, and their pancreatic weights were measured, adjusted for body weight, and analyzed for effects of Smad4 deficiency, sex, and genetic background. Results: The overall population of F1 mice showed a slight but non-significant increase in adjusted pancreatic weights in heterozygous knockout mice compared to wild-type mice. Sex-specific analysis revealed no significant difference in males but a significant increase in adjusted pancreatic weights in heterozygous knockout females. Genetic background analysis showed that lines CC018 and CC025 substantially increased adjusted pancreatic weights in heterozygous knockout mice. In contrast, other lines showed no significant difference or varied non-significant changes. The interplay between genetic background and sex further influenced these outcomes. Conclusion: Smad4 deficiency affects pancreatic weight in a manner significantly modulated by genetic background and sex. This study highlights the necessity of considering these factors in genetic research and therapeutic development, demonstrating the value of the Collaborative cross-mouse population in dissecting complex genetic interactions.

Equine herpesvirus type 1 (EHV-1) causes rhinopneumonitis, abortion and neurological outbreaks (equine herpesvirus myeloencephalopathy, EHM) in horses. EHV-1 also causes lethal encephalitis in laboratory small animals such as mice and hamsters experimentally. EHV-1 ORF76 is a homologue of HSV-1 US9, which is a herpesvirus kinase. Starting with an EHV-1 bacterial artificial chromosome clone of neuropathogenic strain Ab4p (pAb4p BAC), we constructed an ORF76 deletion mutant (Ab4p∆ORF76) by replacing ORF76 with the rpsLneo gene. Deletion of ORF76 had no influence on replication, cell-to-cell spread in cultured cells or replication in primary neuronal cells. In western blots of EHV-1-infected cell lysates, an EHV-1 Us9-specific polyclonal antibody detected multiple bands ranging from 35 to 42-kDa. In a CBA/N1 mouse infection model following intranasal inoculation, the parent and Ab4p∆ORF76 revertant caused the same histopathology in the brain and olfactory bulbs. The parent, Ab4p∆ORF76 and revertant mutant replicated similarly in the olfactory mucosa, although Ab4p∆ORF76 was not transported to the olfactory bulbs and was unable to infect the CNS. These results indicated that the ORF76 (US9) plays an essential role in the anterograde spread EHV-1.

The process of sexual reproduction in eukaryotes starts when gametes from two different sexes encounter each other. Paramecium, a unicellular eukaryote, undergoes conjugation and uses a gametic nucleus to enter the sexual reproductive process. The molecules responsible for recognizing mating partners, hypothetically called mating-type substances, are still unclear. We have identified an O3-type mating substance polypeptide and its gene sequence using protein chemistry, molecular genetics, immunofluorescence, RNA inter-ference, and microinjection. The O3-type substance is a polypeptide found in the ciliary membranes, located from the head to the ventral side of cells. The O3-type substance has a kinase-like domain in its N-terminal part located outside the cell and four EF-hand motifs that bind calcium ions in its C-terminal part located inside the cell. RNA interference and immunofluorescence revealed that this polypeptide positively correlated with the expression of mating reactivity. Microinjection of an expression vector incorporating the O3Pc-MSP gene induced additional O3 mating type in the recipient clones of different mating types or syngen. Phylogenetic analysis indicates this gene is widely present in eukaryotes and exhibits high homology among closely related species. The O3Pc-MSP gene had nine silent mutations compared to the complementary mating type of the E3 homologue gene.

Omicron SARS-CoV-2 variants have dominated the strains of COVID-19 circulating worldwide for the last two years. Although the mortality rate of the COVID-19 Omicron variants is only approximately half that of previous variants, vaccines effective against Omicron are needed. Demonstrating that a SARS-CoV-2 vaccine can protect against Omicron in an in vivo infection model, particularly in that of Syrian hamsters, is important for the preclinical characterization of SARS-CoV-2 vaccines. Here, we report on the evaluation of W-PreS-O for its ability to protect Syrian hamsters against infection by Omicron. W-PreS-O is a chimeric vaccine based on a single fusion protein (W-PreS-O), combining RBDs from Wuhan hu-1 wild-type and Omicron adsorbed to aluminum hydroxide. The Syrian hamsters were immunized three times at three-week intervals with W-PreS-O or with aluminum hydroxide (placebo), and then they were infected with Omicron BA.1. Non-infected and non-vaccinated animals served as controls. Neutralizing antibody (nAB) titers, weight, lung symptoms (i.e., edema and pneumonia index), and viral loads, as measured using RT-PCR in the upper and lower respiratory tracts, were determined. In addition, infectious virus titers from the lungs were measured using a plaque-forming assay. W-PreS-O-vaccinated hamsters developed robust nABs against Omicron, showed almost no development of pneumonia, and had significantly reduced infectious virus titers in the lungs. Importantly, the viral loads in the nasal cavities of W-PreS-O-vaccinated hamsters were close to or above the PCR cycle threshold considered to be non-infectious. Our data provide compelling evidence demonstrating that the W-PreS-O vaccine has protective effect against Omicron in a Syrian hamster in vivo infection model. W-PreS-O is therefore a highly promising candidate vaccine for Omicron infections, and it should be further evaluated in clinical studies.

Diabetes mellitus (DM) poses a significant challenge to global health, with its prevalence projected to rise dramatically by 2045. This narrative review explores the bidirectional relationship between periodontitis (PD) and type 1 diabetes mellitus (T1DM), focusing on cellular and molecular mechanisms derived by the interplay between oral microbiota and the host immune response. A comprehensive search of literature published between 2008 and 2023 was conducted to elucidate the association between these two diseases. Preclinical and clinical evidence suggests a bidirectional relationship, with individuals with T1DM exhibiting heightened susceptibility to periodontitis, and vice versa. The review includes recent findings from human clinical studies, revealing variations in oral microbiota composition in T1DM patients, including increases in certain pathogenic species such as Porphyromonas gingivalis, Prevotella intermedia, and Aggregatibacter actinomycetemcomitans, along with shifts in microbial diversity and abundance. Molecular mechanisms underlying this association involve oxidative stress and dysregulated host immune responses, mediated by inflammatory cytokines such as IL-6, IL-8, and MMPs. Furthermore, disruptions in bone turnover markers, such as RANKL and OPG, contribute to periodontal complications in T1DM patients. While preventive measures to manage periodontal complications in T1DM patients may improve overall health outcomes, further research is needed to understand the intricate interactions between oral microbiota, host response, periodontal disease, and systemic health in this population.

The vomeronasal system serves as a pivotal element in mammalian sensory biology, allowing the perception of chemical signals essential for social communication via the activation of two main receptor families, V1R and V2R. The expression of V1Rs and V2Rs is linked with that of the G-protein alpha-subunits, Gαi2 and Gαo, respectively. The exploration of the evolutionary pathways of V1Rs and V2Rs across all mammalian species remains a main challenge, juxtaposing available genomic data against emerging immunohistochemical evidence. However, recent investigations, in contrast to what is predicted by the currently annotated genomic sequences, have revealed the expression of Gαo in the vomeronasal neuroepithelium of wild canids, including wolves and foxes. In the present study, the employment of a specific antibody raised against the mouse V2R2, member of the C-family of vomeronasal receptors, V2Rs, has confirmed the expression of this receptor in the fox and wolf, but it has revealed the lack of expression in the dog. This may reflect the impact of domestication on the regression of the VNS in this species, in contrast to their wild counterparts, and underscores the effects of artificial selection on sensory functions. Thus, these findings suggest a more refined chemical detection capability in wild species.

(1) Background: Among the chronic complications of type 2 diabetes mellitus, cancer became the leading cause of death in several countries. Our objective was the determination of whether prevalent type 2 diabetes mellitus is associated with a higher incidence of cancer. (2) Methods: This study is a nationwide analysis performed in Hungary. Study population was divided into a group with type 2 diabetes mellitus and into a non-diabetic group. The primary outcome was the risk related to overall cancer incidence. A key secondary outcome was the overall incidence of cancer in distinct study years. Further outcomes were the annual percent changes. (3) Results: The odds ratio related to the overall incidence of cancer was 2.50 (95% confidence interval: 2.46-2.55, P&lt;0.0001) in patients with diabetes as related to controls. The odds ratio was higher in males than in females. The highest risk was found in the 18-39-year-old subgroup. The annual cancer incidence rate declined in controls, but not in patients with diabetes. Several types of cancer showed a decreasing tendency in non-diabetic controls.; (4) Conclusions: type 2 diabetes is associated with a higher risk of cancer. High risk in young patients with type 2 diabetes suggests that these young individuals should be considered as a risk group.

(1) Background: Patients with type 2 diabetes mellitus (T2DM) are at higher risk of cancer but how these two diseases associate is still debated. The goal was the assessment of the overall incidence of cancer among patients with newly diagnosed T2DM in Hungary. Summarizing, incident T2DM is associated with a significantly higher overall risk of incident cancer, with a reverse correlation of age. Newly registered T2DM patients were suggested to be screened for cancer within 6 months. (2) Methods: A nationwide, retrospective, longitudinal study was performed using a Hungarian database. The incident T2DM and diabetes free Hungarian population were included in the study. The primary endpoints were the overall and site-specific incidence and annual percentage change of the incidence of cancer in both populations. (3) Results: The overall incidence of cancer in patients amounted to 29.4/1000 and 6.6/1000 with or without T2DM, respectively, and the OR (95%CI) of cancer of the T2DM group was 4.32 (4.14-4.53), p&lt;0.0001. The risk of having cancer was age-dependent, having the highest odd in the age group 18-39. The incidence of cancer was declining in the non-diabetic but was unchanged in T2DM population. The average lag time of diagnosing a cancer after the detection of T2DM was 3.86 months.; (4) Conclusions: Iincident T2DM is associated with a significantly higher overall risk of incident cancer, with a reverse correlation of age. Newly registered T2DM patients were suggested to be screened for cancer within 6 months.

Non-viral mediated plasmid DNA transfection by electroporation (EP) is an established method for gene transfection. In this study, the usefulness of direct EP at an intradermal (i.d.) site (D_EP) with implanted electrodes to achieve a high protein expression level was investigated. In addition, D_EP application with various intervals with a low application voltage was also evaluated to confirm its effect on protein expression. A higher protein expression level was observed after green fluorescent protein (GFP)- and luciferase-encoding DNA were delivered by i.d. injection followed by D_EP application. When luciferase expression was observed with an in vivo imaging system, continuous expression was confirmed over 21 days after i.d. injection followed by D_EP at 100 V. This approach provided increased gene expression levels compared with conventional EP methods via the stratum corneum layer. In addition, the effect of application voltage on luciferase expression was investigated; two-time applications (repeated D_EP) at 20 V with 5 min intervals showed similar luciferase expression level to single D_EP application with 100 V. Histological observations showed the skin became thicker after a single D_EP at 100 V, whereas no apparent thickness changes was confirmed after repeated D_EP at 20 V with 5 min intervals. This study revealed that direct i.d. voltage application achieved high protein expression levels even at low voltages. Skin is a promising administration site for DNA vaccines, so this approach may be effective in DNA vaccine delivery into skin tissue.

Commuting is a vital travel channel for college students throughout their higher education career; nevertheless, excessive commute time negatively impacts students’ school satisfaction, academic achievement, health, and quality of life. Meanwhile, few studies have explored students’ commute time, covering a large population and scope. Therefore, this study analyzes the dwelling type that influences college and graduate students’ school commute times in the Seoul Metropolitan Area, using data from the 2016 Household Travel Diary Survey. This study uses spatial data on housing development to classify five dwelling types (i.e., new town, housing site development, Seoul, Incheon, and Gyeonggi-do). A multiple linear regression model empirically analyses students’ household and personal characteristics. The results reveal that dwelling type significantly affects students’ commute time. Specifically, Students living in Seoul have a shorter commute to school than those living in new towns. Socioeconomic characteristics have less effect on college and graduate students' school commute time. This study discusses the problem of excessive commuting of college and graduate students in new towns.

Background and Objectives: To investigate the relationship between the SII index and the micro-macro complications and death that develop in the first year and the following 3 years, following the calculation of the index in type 2 diabetic retinopathy patients. Materials and Methods: This study was performed retrospectively with 523 type 2 diabetic retinopathy patients admitted to the endocrinology outpatient clinic of our hospital between January 2019 and December 2019. The demographic, and clinical characteristics of the patients were evaluated using descriptive statistics. Shapiro-Wilk test was used for the normal distribution of quantitative data; Mann-Whitney U, Mc Nemar Chi-square, and Cochran's Q tests were used to analyze SII values between groups and complication rates by years; sensitivity and specificity were determined by ROC analysis and considered statistically significant with a significance level of P

The aim of this study was to investigate the relationship between postprandial glycemic levels based on flash-monitoring and the production of intestinal hydrogen (H2) and methane (CH4) gases based on measurement of the amount of these gases in exhaled air. We studied 14 subjects with type 2 diabetes mellitus (T2DM) and 10 individuals without diabetes (control) with 3 food-load tests with simultaneous determination of gases in exhaled air and assessment of glucose levels. In 15.4% of patients with T2DM, there was a non-significant increase in exhaled H2. How-ever, all subjects in the control group had significant increase in exhaled H2. Moreover, the level of H2 in exhaled breathafter food load in patients with T2DM was lower than in normoglycemic subjects. Also, in normoglycemic subjects there was an inverse correlation between maximum glucose rise and maximum H2 in exhaled air after food load. At the same time in patients with T2DM the level of CH4 in exhaled air directly correlated with the parameters of postprandial glycemia in the test with lactulose. Confirmation of a causal relationship between decreased H2 production, increased intestinal CH4 production, and more severe postprandial glycemia may identify new therapeutic targets in the correction of postprandial glycemia in patients with T2DM.

Weather conditions appear to be undergoing significant deviations from the long-term average, marked by pronounced extremes of heat, prolonged droughts, and heightened rainfall occurring with greater frequency worldwide. Consequently, new patterns of extreme weather are emerging, like the unusual and unorganized tropical cyclone called "Yaku", that influenced the extreme amount of rain that between March 6th to 10th, 2023 hits more than 1000 districts in the northwestern of Peru. One of the district more affected was Íllimo, in the Lambayeque province, due to the river that pass through the city, so called “La Leche”, after the continuous and intensive rain overflow devastating his surrounding areas and causing victims and damage. This emergency provided and excellent opportunity to apply, on the aforementioned areas, the “change detection” technique, that allows identifying areas of change between data obtained before and after of emergency events. In this research, optical data (Sentinel-2, Landsat, MODIS Terra and Aqua, and PeruSAT-1) and synthetic aperture radar (SAR) data (Sentinel-1 and COSMO SkyMed) were analyzed. A benchmark could also be carried out between open-source and commercial spatial analysis tools. The results indicated that in an extreme rain event the optical data are obscured by clouds and do not allow their use, while SAR data overcome clouds, and can be used for this research. The benchmark indicated that using the Jaccard index score, the Sentinel-1A set showed a 33% of correlation, while COSMO SkyMed demonstrated a 38% of match between the maps. The results obtained could be used to sensitize the population and develop a better management of future emergency events (floods) in different areas of Peru.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

The human T-cell leukemia virus type 1 (HTLV-1) is the only known human oncogenic retrovirus. HTLV-1 can cause a cancer called adult T-cell leukemia/lymphoma (ATL). The virus is transmitted through body fluids of infected individuals, primarily breast milk, blood, and semen. At least 5–10 million people in the world are infected with HTLV-1. In addition to ATL, HTLV-1 infection can also cause HTLV-I-associated myelopathy (HAM /TSP). ATL is characterized by low viral ex-pression and poor prognosis. The oncogenesis triggered by HTLV-1 is extremely complex and the molecular mechanisms are not fully understood. However, viral regulatory proteins Tax and HTLV-1 bZIP factor (HBZ) have been shown to play key roles in the transformation of HTLV-1-infected T cells. Moreover, several studies have shown that the final fate of HTLV-1-infected transformed T cell clones is the result of a complex interplay of HTLV-1 oncogenic protein expression with cellular transcription factors that subvert the cell cycle and disrupt reg-ulated cell death, thereby exerting their transforming effects. This review provides updated in-formation on the mechanisms underlying the transforming action of HTLV-1 and the potential therapeutic targets to combat ATL.

We primarily investigate the existence of solutions for fractional neutral integro-differential equations subjected to Neumann-type boundary conditions, which is crucial for understanding natural phenomena. Taking into account factors such as neutral type, fractional-order integrals, and fractional-order derivatives, we employ probability density functions, Laplace transforms, and resolvent operators to formulate a well-defined concept of a mild solution for the specified equation. Following this, by integrating fixed point theorems, we establish the existence of mild solutions under more relaxed conditions.

The Digital electronics collaborative enhanced learning (DECEL) project has recently developed an international collaborative education course. Its main objective is to enhance the digital electronics skills of international students by working on a complex, multidisciplinary applied problem using a mixed digital architecture. We have developed a logic level synthesis and dedicated software layers on the Red Pitaya FPGA platform. The diversity of digital concepts to be implemented, from hardware description language (HDL) to high-level languages such as Python or Matlab, forced the students to work together and rapidly improve their skills. Their motivation was fueled by the curiosity of controlling an ultrasound probe to obtain ultrasound signatures. This particular physics, little known to the students, was an additional source of curiosity. The goal of forming an image in a liquid medium was an additional motivating factor for them. The students reported that they learned a lot from the experiment. Thus, the technical parts and pedagogical results are documented in this work for reproducibility.

Type 2 diabetes mellitus (T2DM) poses a significant economic and clinical burden. Clinical inertia is defined as the failure of healthcare providers to modify therapy in the presence of clear indications. This study aimed to identify patient opinions on insulin to understand the barriers preventing type 2 diabetes patients from initiating insulin treatment when recommended by their physician. This cross-sectional observational study included 671 individuals with poorly controlled T2DM and HbA1c levels exceeding 10%. These patients required either the initiation or escalation of their existing insulin therapy. The participants were referred to Thi-Qar Specialized Diabetes Endocrine and Metabolism Center (TDEMC) for consultation between January 2022 and July 2022.Results: During discussions between the researcher (clinician) and the inadequately controlled T2DM patients, the primary reasons for refusing insulin therapy were identified. These reasons included fear of injections, the belief that insulin induces dependence and is a last resort, concerns about hypoglycemia and complications, cost, difficulty in computing doses, social stigma, inconvenience and disruption to life and work, storage challenges, fear of weight gain, dependence on others, and lack of confidence.The study concludes that the clinical barriers faced by individuals who refuse the initiation of insulin therapy are diverse. The most common belief among the patients was that insulin leads to dependence (38%), while the smallest percentage cited a lack of confidence in insulin as an effective treatment for lowering hyperglycemia.

The Casiquiare River is a natural channel that connects two of the greatest rivers in the world, the Orinoco and the Amazon in the South American Continent. The aim of this paper is to present a review and synthesis of the hydrological and sedimentological knowledge of the Casiquiare River, including the first hydro-sedimentary balance of the Casiquiare fluvial system conducted at the bifurcation and at the mouth on September 9-12, 2000, during the expedition ‘Humboldt-Amazonia 2000’. Bathymetric, flow discharge and physico-chemical measurements were made at the inlet and at the outlet of the Casiquiare Channel. The main conclusions of this study indicate that Casiquiare is taking a significant proportion of flow (20 to 30%) from the Upper Orinoco basin to the Amazon basin. Throughout its 356 km-course, this chameleon channel undergoes significant morphological, hydrological and bio-geochemical variations between the inlet and the outlet, whose most visible witnesses are the increase in its width (3 to 4 times), flow (7 to 9 times) and its change in water color (white to black water), under the influence of tributaries coming from vast forest plains.

This study addresses the enhancement of material efficiency and reduction of brittleness in timber-to-concrete adhesive connections for beam-type timber and timber-concrete composite panels. The research explores the potential benefits of adding longitudinal timber ribs to Cross-Laminated Timber (CLT) beam-type panels. Three groups of flexure-tested specimens were analysed: (1) timber panels (1400 mm × 400 mm) with two 100 mm thick CLT panels and two 60 mm thick CLT panels reinforced with 150x80 mm timber ribs; (2) eight specimens (600 mm × 100 mm × 150 mm) with CLT members (600 mm × 100 mm × 100 mm) connected to a 50 mm concrete layer using granite chips and Sikadur-31 (AB) epoxy adhesive; (3) six CLT panels (1400 mm × 400 mm × 50 mm) bonded to a 50 mm concrete layer, with two panels containing polypropylene microfibers and two panels incorporating polyethene dowels for mechanical connection. Specimens were subjected to three-point bending tests and analysed using the transformed section method, γ-method, and finite element method with ANSYS 2023R2 software. Results indicated a 53% increase in load-carrying capacity for ribbed CLT panels with no additional material consumption, a 24.8%-41.1% increase for CLT panels strengthened with a concrete layer, and improved ductility and prevention of disintegration in timber-concrete composites with polypropylene microfibers.

: Intermittent fasting has drawn significant interest in the clinical research community due to its potential to address metabolic complications such as obesity and type 2 diabetes mellitus. Various intermittent fasting regimens include alternate-day fasting (24 hours of fasting followed by 24 hours of eating), time-restricted fasting (fasting for 14 hours and eating within a 10-hour window), and the 5:2 diet (fasting for two days and eating normally for the other five days). Intermittent fasting is associated with a reduced risk of type 2 diabetes mellitus-related complications and can slow their progression. The increasing global prevalence of type 2 diabetes mellitus highlights the importance of early management. Since prediabetes is a precursor to type 2 diabetes mellitus, understanding its progression is essential. However, the long-term effects of intermittent fasting on prediabetes are not yet well understood. Therefore, this review aims to comprehensively compile existing knowledge on the therapeutic effects of intermittent fasting in managing type 2 diabetes mellitus and prediabetes.

Among the many Lysosomal Storage Disorders (LSDs) that would benefit from the establish-ment of novel cell models, either patient-derived or genetically engineered, is Mucopolysaccha-ridosis type II (MPS II). In fact, even though a specific therapeutic approach does exist for this disorder (Enzyme Replacement Therapy, ERT, with recombinant human IDS) and haematopoiet-ic stem cell transplantation (HSCT) may also hold promise whenever the disorder is diagnosed soon enough, both approaches have their own drawbacks. Here we present our results on the establishment and characterization of two MPS II pa-tient-derived stem cell line(s) from deciduous baby teeth. To the best of our knowledge, this is the first time a stem cell population is isolated from LSD patient samples obtained from the oral cavity. Taking into account our results on the molecular and biochemical characterization of those cells and our first insights on their subcellular MPS phenotype, we consider these cells will be a valuable tool for both pathophysiological assessments and drugs screenings. Ultimately, we believe patient-derived dental pulp stem cells (DPSC) may represent a feasible alternative to induced pluripotent stem cells (iPSC) in many labs with standard cell culture con-ditions and limited (human and economic) resources.