Structures inevitably suffer damages after an earthquake, with their severity ranging from minimal damages to non-structural elements to partial or even total collapse, possibly with loss of human lives. Thus, it is essential for engineers to understand the crucial factors that drive a structure towards suffering higher degrees of damage, so that preventative measures can be taken. In the present study, we focus on three well-known damage thresholds, namely Collapse Limit State, Ultimate Limit State and Serviceability Limit State and analyze which of the features obtained via Rapid Visual Screening, determine whether or not a given structure will cross that threshold. To this end, we use Machine Learning to perform binary classification for each damage threshold, as well as Explainability via SHAP values (acronym for SHapley Additive exPlanations) to quantify the effect of each parameter. The quantitative results obtained demonstrate the potential applicability of ML methods to re-calibrate the computation of structural vulnerability indices using data from recent earthquakes.

The elastic wave equation with the seismic tensorial force is solved in a homogeneous and isotropic medium (the Earth). Spherical-shell waves are obtained, which are associated to the primary P and S seismic waves. It is shown that these waves produce secondary waves with sources on the plane surface of a half-space, which have the form of abrupt walls with a long tail, propagating in the interior and on the surface of the half-space. These secondary waves are associated to the seismic mainshock. The results, previously reported, are re-derived by using Fourier transformations and specific regularization procedures. The relevance of this seismic motion for the ground motion, the seismographs' recordings and the effect of the inhomogeneities in the medium are discussed.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Background: The modified Duke index derived from coronary computed tomography angiography (CCTA) was designed to predict cardiovascular outcomes based on the severity of coronary ste-nosis. However, it does not take into consideration the presence or severity of peri-coronary in-flammation. The peri-coronary fat attenuation index (FAI) is a novel imaging marker determined by CCTA which reflects the degree of inflammation in the coronary tree in patients with coronary artery disease. Purpose: To assess the association between the modified Duke index assessed by CCTA, cardiovascular risk factors and peri-coronary inflammation in the coronary arteries of pa-tients with coronary artery disease. Methods: One hundred seventy-two patients who underwent CCTA for typical angina were assigned into two groups based on the modified Duke index: group 1 – patients with low index ≤ 3 (n=107) and group 2 – patients with high index > 3 (n=65). Demo-graphic, clinical and CCTA data were collected for all patients, and FAI analysis of coronary in-flammation was performed. Results: Patients with increased values of the modified Duke index were significantly older compared to those with a low index (61.83 ± 9.89 vs. 64.78 ± 8.9; p = 0.002). No differences were found between the two groups in terms of gender distribution, hypertension, hypercholesterolemia or smoking history (all p > 0.5). The FAI score was significantly higher in patients from group 2, who presented a significantly higher score of inflammation compared to the patients in group 1, especially at the level of the right coronary artery (FAI score 20.85 ± 15.80 vs. 14.61 ± 16.66; p = 0.01 for the right coronary artery, 13.85 ± 8.04 vs. 10.91 ± 6.5; p = 0.01 for the circumflex artery, and 13.26 ±10.18 vs. 11.37 ± 8.84; p = 0.2 for the left anterior descending artery). CaRi-Heart® analysis identified a significantly higher risk of future events among patients with a high modified Duke index (34.84 % ± 25.86 % versus 16.87 % ± 15.80 %; p

We present an idea how to use long-wavelength multi-wavelength radio continuum observations of spiral galaxies to isolate magnetic structures which were previously accessible from short-wavelength observations only. The approach is based on the RM-synthesis and 2D continuous wavelet transform. Wavelet analysis helps to recognize a configuration of small-scale structures which are produced by Faraday dispersion. We find that these structures can trace galactic magnetic arms for the case of the galaxy NGC 6946 observed at $\lambda = 17 \div 22$~cm. We support this interpretation by an analysis of a synthetic observation obtained using a realistic model of a galactic magnetic field.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

A reliability-based criterion to estimate strength amplification factors for buildings with asymmetric yielding located within a seismic region presenting different soil conditions is proposed and applied. The approach involves the calculation of the mean annual rate of exceedance of structural demands of systems with different levels of asymmetric yielding. Two simplified mathematical expressions are developed considering different soil conditions of the valley of Mexico. The mathematical expressions depend on the ductility of the structural systems, their level of asymmetric yielding, their fundamental vibration period and the dominant period of the soil. In addition, the proposed expressions are compared with that recommended by the current Mexico City Building Code (MCBC). Since the expressions are developed with the help of simplified structural systems, the validity of such expressions is corroborated by comparing the expected ductility demand of multi-degree of freedom (MDOF) structural systems with respect to that of their equivalent simplified systems. Both structural representations are associated with a given annual rate of exceedance value of an engineering demand parameter. The expressions proposed in this study will be incorporated in the new version of the MCBC.

Breast cancer has become the most diagnosed cancer in women globally with 2.3 million new diagnosis each year. Accurate early staging is essential for improving survival rates with metastatic spread from loco regional to distant metastasis decreasing rates by 50%. Current guidelines do not advice the routine use of Positron Emission Tomography (PET)-Computed Tomography (CT) in staging of early breast cancer in the absence of symptoms. However, there is a growing body of evidence to suggest that PET-CT used in this early stage can benefit the patient by improving staging and as a result treatment and outcome as well as psychological burden without increasing costs to the health service. Ongoing research in PET radiomics and artificial intelligence is showing promising future prospects in its use in diagnosis, staging, prognosticatication and assessing response to treatment in breast cancer. Furthermore ongoing research to address current limitations of PET-CT by improving techniques and tracers is encouraging.

Diffuse optical tomography (DOT) is an optical medical imaging method that can assess the structural properties of tissues and their functional characteristics, such as hemoglobin concentration, water content, as well as lipid concentration, via three-dimensional image reconstruction. This paper presents the theoretical basis and working principle of diffuse optical tomography. The paper explains how the optical properties of tissue can be imaged by photon migration techniques based on diffusion theory. The author presents the reasoning for near-infrared (NIR) imaging as the most effective technique in terms of quantitative recovery of spectroscopic optical parameters. This work also listed various advantages, applications, and challenges of DOT. The paper also briefly discusses current progress in near-infrared medical imaging and its future direction.

We use earthquake ground motion modelling via Ground Motion Prediction Equations (GMPEs) and numerical simulation of seismic waves to consider the effects of site amplification and basin resonance in Jakarta, the capital city of Indonesia. While spectral accelerations at short periods are sensitive to near-surface conditions (i.e., Vs30), our results suggest that, for basins as deep as Jakarta’s, available GMPEs cannot be relied upon to accurately estimate the effect of basin depth on ground motions at long periods (>1 s). Amplitudes at such long periods are influenced by entrapment of seismic waves in the basin, resulting in longer duration of strong ground motion, and interference between incoming and reflected waves as well as focusing at basin edges may amplify seismic waves. In order to simulate such phenomena in detail, a basin model derived from a previous study is used as a computational domain for deterministic earthquake scenario modeling in a 2-dimensional cross-section. A M_w 9.0 megathrust, a M_w 6.5 crustal thrust and a M_w 7.0 instraslab earthquake are chosen as scenario events that pose credible threats to Jakarta, and the interactions with the basin of seismic waves generated by these events were simulated. The highest PGV amplifications are recorded at sites near the middle of the basin and near its southern edge, with maximum amplifications of PGV in the horizontal component of 200% for the crustal, 600% for the megathrust and 335% for the deep intraslab earthquake scenario, respectively. We find that the levels of ground motion response spectral acceleration fall below those of the 2012 Indonesian building Codes's design response spectrum for short periods (< 1 s), but closely approach or may even exceed these levels for longer periods.

Diffuse optical tomography (DOT) is a medical imaging procedure using light to measure the geometric and working properties of cells, for instance, oxygen consumption, water content, and fat percentage in the tissue by performing three-dimensional visualization of the tissue. This paper aims to explain the theory behind diffuse optical tomography imaging and how the technology works. The paper explains how photon migration techniques based on diffusion theory can be used to image the optical properties of tissue. There are several reasons why near-infrared (NIR) imaging is the most effective method in terms of recovering optical parameters quantitatively in the near-infrared region. The author discusses the methods in detail. This research also presents various advantages, practical uses, and potential problems that have been related to DOT in this work. There is also a brief discussion of current research developments in medical imaging using near-infrared wavelengths, and what the future holds for that area.

Background: Endogenous Candida endophthalmitis (ECE) is a rare but sight-threatening disease. Patients with ECE present with various clinical signs and symptoms, which can complicate the diagnosis. The aim of this report was to describe the characteristic features of ECE on optical co-herence tomography (OCT) and OCT angiography (OCTA). Another objective was to demon-strate the outcomes of treatment and to diagnose macular complications caused by intraocular inflammation. Case presentation: A 41-year-old woman with a history of acute intermittent por-phyria presented with a progressive vision loss in her left eye. Left-eye OCT revealed findings consistent with a fungal etiology, which was confirmed by the culture of swabs collected from a central vein catheter. The outcomes of intravenous fluconazole treatment were not satisfactory, and the patient developed recurrent attacks of porphyria, suggesting a porphyrogenic effect of systemic antifungal therapy. Repeated intravitreal injections with amphotericin B led to a gradu-al regression of inflammatory lesions. However, follow-up examinations revealed active macular neovascularization on both OCT and OCTA. The patient was administered intravitreal bevaci-zumab. Conclusions: This case highlights the importance of OCT and OCTA as valuable noninva-sive imaging techniques for the identification of ECE, the monitoring of its clinical course, and the diagnosis of macular complications.

Objective: Polymyalgia rheumatica (PMR) and giant cell arteritis (GCA) are often overlapping conditions. We aimed to determine whether 18F-fluorodeoxyglucose (FDG) positron emission tomography-computed tomography (PET-CT) is useful in identifying PMR in the setting of large vessel vasculitis (LVV)-GCA. Methods: Patients diagnosed with LVV-GCA by PET-CT at a tertiary referral hospital for a population of 450,000 people over a two-year period were reviewed. Scoring was performed based on potential significant FDG uptake at up to 16 sites in nine different extravascular areas (SCORE 16). Differences in extravascular sites of significant FDG uptake were evaluated between LVV-GCA with a clinical diagnosis of PMR or not. Results: Fifty-four patients were diagnosed with LVV-GCA by 18F-FDG-PET-CT. Of them, 21 (38.8%) were clinically diagnosed with PMR. Significant extravascular FDG uptake was more frequently observed in those with a clinical diagnosis of PMR. In this sense, the SCORE 16 was higher in those with clinical PMR (5.10 ± 4.05 versus 1.73 ± 2.31 in those without a clinical diagnosis of PMR; p< 0.001). A SCORE 16 involving more than 4 sites of significant FDG uptake yielded a sensitivity of 52% and a specificity of 91% for establishing a clinical diagnosis of PMR associated with LVV-GCA. The best areas of significant FDG uptake to clinically identify PMR in patients with LVV were the shoulder, the greater trochanter and the lumbar interspinous regions with an area under the ROC curve of 0.810 (0.691-0.930). Conclusion: Significant extravascular 18F-FDG-PET-CT uptake may help establish a clinical diagnosis of PMR in patients with LVV-GCA. These patients are more commonly diagnosed with PMR if they have significant FDG uptake in the shoulder, greater trochanter, and lumbar interspinous areas.

To study the strengthening effect on recycled concrete columns by carbon fiber composite materials (CFRP) under different levels of seismic damage, four column specimens were designed for pseudo-static tests. The four specimens were respectively non-destructive without strengthening (prototype), non-destructive strengthening, medium seismic damage strengthening and severe seismic damage strengthening, according to the replacement rate of recycled aggregates and the level of seismic damage. The characteristics of the deformation damage and seismic performance indicators of each specimen were compared and analyzed. A decrease was observed in the initial stiffness of the seismically damaged recycled concrete column specimens strengthened with CFRP, while the ductility, peak bearing capacity and energy dissipation capacity of the specimens were improved. On the other hand, with the reduction of seismic damage and the increase of recycled aggregate replacement rate, the ductility and energy dissipation capacity of the reinforced seismic damaged recycled concrete column specimens were enhanced to different levels. In particular, the cumulative energy consumption of the strengthened specimens under medium seismic damage increased most significantly by 32.5%. In general, the hysteretic curves of the strengthened specimens were full, and the average ductility coefficients were 4.1–6.8. CFRP strengthening was more effective in restoring and enhancing the performance of the recycled concrete column specimens with medium and lower seismic damage levels (displacement ratio ≤ 3%).

The problems of formation and propagation of surface seismic waves in vertically layered and horizontally inhomogeneous media are studied. A mathematical model has been developed for the propagation of surface seismic waves in an inhomogeneous medium based on the use of the fundamental principles of wave dynamics and Fourier transforms. The existence of various types of groups of these waves is proved, and their main properties are studied. It has been established that the reflection coefficients of different groups of a dispersive wave on models of half-spaces (a layered, inhomogeneous medium) with a sharp velocity differentiation are characterized by the same dependence on the angle of incidence as in the absence of dispersion. In the region of the critical angle, which depends on the period of the incident wave, a local decrease in the intensity of wave reflection is observed, which is associated with the origin of the head dispersive wave. It has been found that the reflection coefficients of Rayleigh waves from low-velocity layers, thin (d / λ2 = 0.205) and thick (d / λ2 = 0.82) are approximately 0.2 ± 0.04 and practically do not change with increasing angle of incidence. On the basis of theoretical studies, it was revealed that reflected surface waves carry information both about the elastic properties of the reflecting medium and about the dimensions of the reflecting horizontal inhomogeneity. An experimental dispersion curve of the group velocity of Rayleigh waves on the Central Asia-Caucasus path has been obtained. The seismic stress state of the "subgrade-base" system was studied. Based on the analysis of the results of numerical experiments, it has been established that in order to obtain a complete picture of the seismically stressed state of the subgrade, it is necessary to take into account the contribution to it of each component of the accelerogram of a real earthquake.

18F-fluorodeoxyglucose positron emission tomography and computed tomography (18F-FDG PET-CT) is increasingly used in the diagnosis, prognosis, staging, and treatment monitoring of many tumor types. However, only a small number of studies have reported the use of 18F-FDG PET-CT in intrahepatic cholangiocarcinoma (ICC). This study aimed to examine the accuracy of tumor staging in ICC by using 18F-FDG PET-CT. Between January 2009 and December 2020, patients with suspected ICC were retrospectively enrolled in the study and underwent imaging. The sensitivity and specificity of 18F-FDG PET-CT, CT, and magnetic resonance imaging (MRI) in detecting tumors, satellite focus, vascular invasion, and lymph node metastases were analyzed. The efficacy of 18F-FDG PET-CT for tumor staging was evaluated. Of the 110 patients who were enrolled in the study, 52 underwent surgical treatment and 45 were histologically diagnosed with ICC. When compared with CT or MRI, 18F-FDG PET-CT had similar sensitivity and specificity values for diagnosing satellite focus and vascular and bile duct invasion; however, PET-CT showed higher accuracy in diagnosing regional lymph node metastases. The accuracy of tumor staging by 18F-FDG PET-CT was higher than that by CT/MRI. Thus, 18FDG PET-CT may support tumor staging in ICC.

MzSTools is a plugin for QGIS developed by the Institute of Environmental Geology and Geoengineering of the National Research Council (CNR-IGAG). The plugin has been designed as a set of practical and easy-to-use tools to carry out seismic microzonation (SM) studies, by producing standard compliant geographic database and maps, thus making them accurate, homogeneous and uniform for all municipalities in Italy. A geodatabase based on SQLite/SpatiaLite Relational Database Management System (RDBMS) has been designed to collect and store data related to elements such as: geognostic surveys; bedrocks and cover terrains; superficial and buried geomorphological elements; tectonic-structural elements; elements of geological instability such as landslide zones, liquefaction zones and zones affected by active and capable faults; homogeneous microzones in seismic perspective, microzones characterized by a seismic amplification factor. MzSTools assembles in a single software environment a set of useful tools in a configurable QGIS project template, comprising layers, symbol libraries, cartographic styles and print layouts for the SM maps. The plugin is open source and hosted on the GitHub platform, and available via the official QGIS plugins repository (https://plugins.qgis.org/plugins/MzSTools/).

Abstract: Seismic performance and loss assessments can have widely varying degrees of uncertainty. An essential issue is whether a particular assessed seismic loss or performance result has sufficient reliability to serve as the basis for risk management decisions and actions, including whether or not a code prescribed performance level is met, or if an assessed loss level is acceptable. A method is developed measuring the reliability of performance and loss assessments for individual buildings and for portfolios. Consideration is given to how well the building investigation and corresponding evaluation process have been performed, the qualifications of the person(s) doing the assessment, the thoroughness of the evaluation, and the technical validity of the assessment procedure or model. The approach characterizes the uncertainty of each component of the assessment procedure for each building in qualitative terms. The resulting reliability measure is likely to be most useful for the cases where an entity is determining whether/or not a building has acceptable life safety performance, or if a portfolio has an acceptably low risk of seismic damage loss over a given period of time. In both cases, the reliability must either be sufficient to warrant action, or serve to indicate need for improved assessment.

Engineering of quantum computers requires reliable characterization of qubits, quantum operations, and even the entire hardware. Quantum tomography is an indispensable framework in quantum characterization, verification, and validation (QCVV), which has been widely accepted by researchers. According to the tomographic target, quantum tomography can be categorized into quantum state tomography (QST), quantum process tomography (QPT), gate set tomography (GST), process tensor tomography (PTT), and instrument set tomography (IST). Standard quantum tomography toolkits generally consist of basic linear inverse methods and statistical maximum likelihood estimation (MLE) based methods. Furthermore, the performance of standard methods, including effectiveness and efficiency, has been further developed by exploiting Bayesian estimation, neural networks, matrix completion techniques, etc. In this review, we introduce the fundamental quantum tomography techniques, including QST, QPT, GST, PTT, and IST. We first introduce the details of basic linear inverse methods. Then, the framework of MLE methods with constraints is summarized. Finally, we briefly introduce recent further research in developing the performance of tomography. This review provides a primary getting-start in developing quantum tomography, which promotes quantum computer development.

Background: Pulmonary sequestration (PS), generally diagnosed using computed tomography pulmonary angiography (CTPA), is a rare congenital developmental malformation of the lung that is characterized by nonfunctional lung tissue independent of the normal lung tissue. This study summarizes the imaging features of the supplying arteries and draining vessels in patients with PS with an aim to assist with timely clinical diagnosis and operation guidance. Materials and Methods: A total of 55 patients with PS diagnosed on CTPA from multiple clinical centers were retrospectively analyzed. Data included demographic characteristics, imaging features, disease location, isolation type, and the features of supplying and draining vessels, as shown on CTPA images. Results: Of the 55 patients reviewed, 3 (5.45%) were children, 3 (5.45%) were adolescents, and 49 (89.09%) were adults, with a mean age of 44 years. Fifty-four (98.18%) patients had intralobar sequestration and one (1.82%) had extralobar sequestration. PS was noted 3.5 times more frequently in the left lower lobe than in the right lower lobe. For the supplying arteries, 47 (85.45%) were derived from the descending thoracic aorta, 1 (1.82%) from the abdominal aorta, 7 (12.73%) from the celiac axis, and 1 (1.82%) from the bronchial artery. The draining vessels were the pulmonary veins in 49 patients (89.09%), the umbilical vein in 1 (1.82%), the venae intercostal in 1 (1.82%), the pulmonary arteries in 11 (20.00%), and not shown on the images in 2 (3.64%). Conclusion: Clinical presentations of PS are non-specific and can be easily missed or misdiagnosed. However, CTPA can help improve the diagnostic accuracy and identify the supplying arteries and draining vessels, which significantly contribute to surgical planning.

Seismic velocity inversion is one of the most critical issues in the field of seismic exploration and has long been the focus of numerous experts and scholars. In recent years, the advancement of machine learning technologies has infused new vitality into the research of seismic velocity inversion and yielded a wealth of research outcomes. Typically, seismic velocity inversion based on machine learning lacks control over physical processes and interpretability. Starting from wave theory and the physical processes of seismic data acquisition, this paper proposes a method for seismic velocity model inversion based on Physical Embedding Recurrent Neural Networks. Firstly, the wave equation is a mathematical representation of the physical process of acoustic waves propagating through a medium, and the finite difference method is an effective approach to solving the wave equation. With this in mind, we introduce the architecture of recurrent neural networks to describe the finite difference solution of the wave equation, realizing the embedding of physical processes into machine learning. Secondly, in seismic data acquisition, the propagation of acoustic waves from multiple sources through the medium represents a high-dimensional causal time series (wavefield snapshots), where the influential variable is the velocity model, and the received signals are the observations of the wavefield. This forms a forward modeling process as the forward simulation of the wavefield equation, and the use of error back-propagation between observations and calculations as the velocity inversion process. Through time-lapse inversion and incorporating the causal information of wavefield propagation, the non-uniqueness issue in velocity inversion is mitigated. Through mathematical derivations and theoretical model analyses, the effectiveness and rationality of the method are demonstrated. In conjunction with simulation results for complex models, the method proposed in this paper can achieve velocity inversion in complex geological structures.

The correlations of seismic noise, recorded during 1997-2022 at 229 stations around the world are investigated. The property of waveforms, known as the Donoho-Johnston threshold, is analyzed, which separates the absolute values of the orthogonal wavelet coefficients into "small" and "large". Network of 50 reference points is considered. For each reference point, a time series with a time step of 1 day is calculated as the median of the values of the DJ index from the 5 nearest stations. For each reference point, the correlations between the values of the DJ index at other reference points are calculated in a sliding time window of 365 days. Average values of the DJ index decrease, which is interpreted as indicators of global seismic hazard increasing. The maximum distances between reference points with strong correlations show an explosive increase after 2011. Bursts in the mean coherences between the length of day (LOD) and the values of the DJ index at the reference points precede the release of seismic energy with a delay of about 530 days. High amplitude of the DJ index response to LOD for the times 2020-2022 was identified, which may forecast a strong earthquake in the second half of 2023.

The assessment of seismic risk in urban areas with high seismicity is certainly one of the most important problems that territorial managers have to face. A reliable evaluation of this risk is the basis for the design of both specific seismic improvement interventions and emergency management plans. Unappropriate seismic risk assessments may provide misleading results and induce bad decisions with relevant economic and social impact.The seismic risk in urban areas is mainly linked to three factors, namely, “hazard”, “exposure” and “vulnerability”. Hazard measures the potential of an earthquake to produce harm; exposure evaluates the amount of population exposed to harm; vulnerability represents the proneness of considered buildings to suffer damages in case of an earthquake. Estimates of such factors may not always coincide with the perceived risk of the resident population. The propensity to implement structural seismic improvement interventions aimed at reducing the vulnerability of buildings depends significantly on the perceived risk.This paper investigates on the difference between objective and perceived risk and highlights some critical issues. The aim of this study is to calibrate opportune policies, which allow addressing the most appropriate seismic risk mitigation options with reference to current levels of perceived risk. We propose the introduction of a Seismic Policy Prevention index (SPPi). This methodology is applied to a case-study focused on a densely populated district of the city of Catania (Italy).

In this work the seismic resilience of the Emergency Department of a real Hospital complex, located in Tuscany (Italy), has been quantified, with special reference to its nonstructural components and organizational features. Special attention has been paid to the ceilings, whose importance stood out in past earthquakes. A comprehensive meta-model has been set, able to relate all the considered parameters to the assumed response quantity, i.e. the waiting time of the red-code patients arriving to the Emergency Department in the hours immediately after the seismic event. The seismic resilience of the Emergency Department has been measured with reference to earthquakes compatible to the seismic hazard of the area.

Fault detection is an important step for subsurface interpretation and reservoir characterization from 3D seismic images. Due to the numerous and complicated faulting structures of seismic images, manual seismic interpretation is time taking and need intensive work. To overcome this problem, geoscientists are coming up with productive computer-aided techniques for assisting in interpreter science for many years. However, in this paper, we used a pre-trained CNN model to predict faults from the 3D seismic volume of the Poseidon field of Browse Basin, Australia. Basically, this field is highly structured with complex normal faulting throughout the targeted Plover Formations. So, our motivation for this work in this field is to compare machine learning-based fault prediction to user interpreted faults identification with supported by seismic variance attribute. We found very satisfying result using DL with having an improved fault probability volume that outperform variance technology. Therefore, we propose that this workflow could reduce time and able to predict fault quite accurately in any field area.

Accurate image registration is essential for eye movement compensation in optical coherence tomography (OCT) and OCT angiography (OCTA). The spatial resolution of an OCT instrument is typically anisotropic, i.e., different resolutions in the lateral and axial dimensions. When OCT images have anisotropic pixel resolution, residual distortion (RD) and false translation (FT) were always observed after image registration for rotational movement. In this study, RD and FT were quantitively analyzed over different degrees of rotational movement and various lateral and axial pixel resolution ratio (RL/RA) values. The theoretical analysis confirmed that the RD and FT increase significantly with the rotation degree and RL/RA. An image resizing assisting registration (RAR) strategy was proposed for accurate image registration. The performance of direct registration (DR) and RAR for retinal OCT and OCTA images were quantitatively compared. Experimental results confirmed that unnormalized RL/RA causes RD and FT, RAR can effectively improve the performance of OCT and OCTA image registration and distortion compensation.

The analysis of the radon-seismicity relationship has been carried out so far in the Vrancea (Ro-mania) seismic zone, with monitoring stations positioned on tectonic faults. The article analyzes the evolution of radon under the conditions of the existence of deep and surface seismicity and the presence of mud volcanoes along with live fires caused by gases emitted from the soil. The monitoring area was extended to the Black Sea and the area of the Făgăraș Câmpulung fault, where a special radon detection system was set up, which was proposed for patenting. A case study is the effect of the earthquakes in Turkey (7.8 R and 7.5 R on 2023/02/06) on the seismically active areas in Romania in terms of gas emissions (radon, CO2). The main analysis methods on radon (we also included CO2) are applied to integrated time series and the use of anomaly detection algorithms. Data analysis shows that the effects of global warming introduce deviations in seasonal gas emissions compared to previous years. This makes it difficult to analyze the data and correlate them with seismicity. The main conclusions related to the development of a radon monitoring network and in general the emission of gases in seismic areas refer to the importance of the choice of equipment, the monitoring location and the installation method.

Mediterranean Ridge accretionary complex (MAC) is one of the most critical subduction zones in the world. It is known that the region exhibits a continuous mass change (horizontal/vertical movements). This process is associated with the devastating and tragic earthquakes shaking the MAC for centuries. Here, we investigate the ocean bottom pressure (OBP) anomalies in the MAC derived from the Gravity Recovery and Climate Experiment (GRACE) and GRACE Follow On (GRACE-FO) satellite missions. The OBP time series for the MAC comprises a decreasing trend in addition to 1-, 1.53-, 2.36-, 3.67-, and 9.17-year periodic components partially explained by the atmosphere, oceans, and hydrosphere (AOH) processes, and Earth's pole movement. We noticed that the OBP anomalies appear to link to a rising trend and periods in earthquakes' power time series. This finding sheds new light on the mechanisms controlling the most destructive natural hazard.

ABSTRACT Objectives: Typical Diagnostic Reference Levels (DRL) in terms of Computed Tomography Dose Index (CTDI) and patient dose in terms of Effective Dose (ED ) and Size Specific Dose Estimate (SSDE) were estimated in Computed Tomography (CT) guided biopsy procedures. Materials and Methods: A total of 226 CT biopsy procedures - Iliac bone, liver, lung, mediastinum and para-aortic tissue - were retrospectively analyzed and Typical DRL extracted based on ICRP 135 instructions. Results: For helical mode acquisitions, DRLs in terms of CTDIvol were 9.7 mGy for Iliac bone, 8.9 mGy for liver, 8.8 mGy for lung, 7.9 mGy for mediastinal mass and 9 mGy for para-aortic lymph nodes biopsy procedures. For biopsy acquisitions, DRL values were 7.3 mGy, 7.7 mGy, 5.6 mGy, 5.6 mGy and 7.4 mGy respectively. Also, SSDE median values ranged from 7.6 mGy to 10 mGy for biopsy acquisitions and 11,3 mGy to 12,6 mGy for helical acquisitions, as well as the median values for effective dose ranged from 1.6 mSv to 5,7 mSv for biopsy scans and 3.9 to 9.3 mSv for helical scans. Conclusions: The use of DLR as an optimization tool for CT-guided biopsy procedures revealed that helical scans across the entire anatomical region greatly affect radiation dose compared to biopsy acquisitions.

Background and purpose: Dynamic 18F-FDG PET-CT scanning can accurately quantify 18F-FDG uptake and has been successfully applied in diagnosing and evaluating therapeutic effects in various malignant tumors. There is no conclusion as to whether it can accurately distinguish benign and malignant lymph nodes in nasopharyngeal cancer. The main purpose of this study is to reveal the diagnostic value of dynamic PET-CT in cervical lymph node metastasis of nasopharyngeal cancer through analysis. Method: We first searched for cervical lymph nodes interested in static PET-CT, measured their SUV-Max values, and found the corresponding lymph nodes in magnetic resonance images before and after treatment. The valid or invalid groups were included according to the changes in lymph node size before and after treatment. Their Ki values were measured on dynamic PET-CT and compared under different conditions. Then, we conducted a correlation analysis between different factors and Ki values. Finally, diagnostic tests were conducted to compare the sensitivity and specificity of Ki and SUV-Max. Result: We included 67 cervical lymph nodes from different regions of 51 nasopharyngeal cancer patients and divided them into valid and invalid groups based on changes before treatment. The valid group includes 50 lymph nodes, while the invalid group includes 17. Significant differences (P<0.001) between the two groups in SUV-Max, Ki-Mean, and Ki-Max values. When the SUV-Max≤4.5, there was no significant difference in the Ki-Mean and Ki-Max between the two groups (P>0.05). When SUV-Max≤4.5 and pre-treatment lymph nodes<1.0cm, the valid group had significantly higher Ki-Mean (0.00910) and Ki-Maximum (0.01004) values than the invalid group (Ki-Mean=0.00716, Ki -Max=0.00767) (P<0.05). When SUV-Max≤4.5, pre-treatment lymph nodes<1.0cm, and EBV DNA replication was normal, Ki-Mean (0.01060) and Ki-Max (0.01149) in the valid group were still significantly higher than the invalid group (Ki-Mean=0.00670, Ki-Max=0.00719) (P<0.05). The correlation analysis between different factors (SUV-Max, T-stage, normal EB virus DNA replication, age, pre-treatment lymph node<1.0cm) and Ki value showed that SUV-Max and pre-treatment lymph node<1.0cm were related to Ki-Mean and Ki-Max. Diagnostic testing was conducted, the AUC value of the SUV-Max value was 0.8259 (95% confidence interval: 0.7296-0.9222), the AUC value of the Ki-Mean was 0.8759 (95% confidence interval: 0.7950-0.9567), and the AUC value of the Ki-Max was 0.8859 (95% confidence interval: 0.8089-0.9629). It was found that the sensitivity of SUV-Max was 88%, the specificity was 76%, the sensitivity of Ki-Mean was 88%, the specificity was 80%, the sensitivity of Ki-Max was 94%, the specificity was 76%, the specificity of Ki-Mean was better than SUV-Max, the sensitivity of Ki-Max was better than SUV-Max. Conclusion: Dynamic PET-CT has shown significant diagnostic value in diagnosing cervical lymph node metastasis of nasopharyngeal cancer, especially for the small SUV value, and lymph nodes do not meet the metastasis criteria before treatment, and EBV DNA replication is normal. Moreover, its sensitivity and accuracy are superior to static PET-CT.

A contemporary technique for calculating seismic risk is earthquake nowcasting (EN), which analyzes the progression of the earthquake (EQ) cycle in fault systems. 'Natural time' is a novel idea of time that serves as the foundation for EN assessment. The earthquake potential score (EPS), which has been discovered to have useful uses regionally and worldwide, is a unique tool EN uses to predict seismic risk. For the estimation of the EPS for the occurrences with the highest magnitude among these applications, we have since 2021 concentrated on Greece territory, applying sophisticated Artificial Intelligence (AI) algorithms, both wise (semi)supervised and unsupervised models, along with a customized dynamic sliding window technique that performs as a stochastic filter able to fine-tune the geo seismic occurrences. Long short-term memory (LSTM) neural networks, random forests, and clustering (geospatial) models are three machine learning techniques that are particularly good at finding patterns in vast databases and may be used to enhance earthquake prediction performance. In this study, we attempt to forecast whether practical Machine-learning and AI/Game-theoretic-based approaches can help predict big earthquakes and the normal future seismic cycle for 6-12 months. Specifically, we focus on answering two questions for a given region: (1) Is there a chance that a significant earthquake—say, one with a magnitude of M ≥ 6.0 will happen in the upcoming year? (2) What is the largest earthquake magnitude predicted in the upcoming year, and with which exact geographic coordinates (GCS)? Our results are quite promising and project a high precision accuracy score (≥ 98%) for seismic nowcasting in terms of four predictive parameters: the approximate (a) latitude, (b) longitude, (c) focal depth, and (d) magnitude of the phenomena.

Despite the fact that SMA restrainers exhibit a superelastic strain capacity of 7%, this capacity appears inadequate for isolated bridges due to the typically greater than 20cm relative dis-placements between girders during intense seismic events. In order to perform such a stroke, a SMA restrainer of greater than 3 metres in length might be required. In order to reduce the length of restrainers, a novel honeycomb damper constructed from superelastic shape memory alloy (SMA) is proposed. The proposed device, denoted as the superelastic SMA honeycomb damper (SHD), is comprised of steel plates to prevent the SMA plane from collapsing and superelastic SMA honeycomb to provide self-centering capability. By incorporating the large strain capacity of SMA and the geometrically nonlinear deformation of honeycomb structures, SHD has been developed to satisfy the requirements of bridge restrainers with large strokes. It is capable of functioning as a restrainer and energy dissipation device when subjected to dynamic tension and compression loads. The SHD was initially investigated from a theoretical perspective. Following this, a mul-ti-cell SHD specimen was manufactured. The specimen underwent axial tensile and compressive experiments in order to examine the mechanical properties of SHDs. Finally, experimental results were investigated through numerical simulation analyses of the SHDs using a three-dimensional high-fidelity finite element model. Additionally, a method for enhancing SHD was proposed. The findings indicate that SHD is capable of exhibiting superior self-centering capability and sta-ble hysteretic responses when subjected to earthquakes.

In recent decades, low-yielding seismic devices based on the use of friction dampers have emerged as an excellent solution for the development of building structures with improved reparability and resilience. Achieving an optimal design for such low-yielding seismic devices requires precise control of bolt preloading levels and predictability of the friction coefficient (CoF) between the damper interfaces. While various types of friction devices exist, capable of providing significant energy dissipation, ongoing research is focused on the development of novel friction materials that exhibit a stable hysteretic response, high CoF values, minimal differences between static and dynamic CoF, and predictable slip resistance. In this context, an experimental campaign was conducted at the STRENGTH Laboratory of the University of Salerno to evaluate the behaviour of new friction shims employing specially developed metal alloys. Specifically, the influence of the characteristics of the contact surfaces in the sliding area on the behaviour and performance of the friction device was analysed. The tests followed the loading protocol recommended by EN12159 for seismic device qualification. Monitored parameters included preloading force values and the evolution of slip resistance. The friction value was determined, along with its degradation over time. Finally, the material's performance in terms of hysteretic behaviour was assessed, providing a comparison of the tested specimens in terms of slip force degradation and energy dissipation capacity.

(1) Background: The intermediate-depth seismicity in the Vrancea region (Romania) is characterized by localized and persistent earthquake activity that culminates about two or three times in a century with the occurrence of a large event (M 6.5). Here we have revisited some important seismicity characteristics, using earthquake catalog data spanning two different time periods: 2005 – 2013 and 1960 – 2000. (2) Methods: we have determined the b-value of the frequency-magnitude distribution of earthquakes, using a maximum likelihood procedure, and estimated the parameter to quantify anomalous seismicity rate decreases and increases. (3) Results: by using data from the first period, we have confirmed the existence of a decreased b-value in the deepest part of the seismogenic zone; by using data from the second period, we have statistically confirmed the seismic quiescence that preceded the occurrence of the 1977 M7.4 Vrancea earthquake. (4) Conclusions: the decreased b-value has been interpreted either in terms of an increased lithostatic stress with depth or as an indicator of the depth range where the next major Vrancea earthquake may occur. The time variation of the seismicity parameter may reveal anomalous seismic quiescence and increased earthquake rates that may precede the occurrence of large earthquakes.

While the container crane is an important part of daily port operations, it has received little attention compared with other infrastructures, such as buildings and bridges. Crane collapse due to earthquake affects the operation of the port, and indirectly impacts the economy. This study proposes fragility analyses for various damage levels of the container crane that allow the port owner and partners to better understand the seismic vulnerability presented by container cranes. A large quantity of nonlinear time history analyses was applied for a three-dimensional (3D) finite element model to quantify the vulnerability of the container crane in considering the uplift and derailment behavior. The uncertainty of demand and capacity of the crane structures were also considered through random variables, i.e. elastic modulus of members, ground motion profile, and intensity. The results analyzed in the case of a Korean container crane showed that the probability of exceeding the first uplift with or without derailment is shown before the crane reaches the structure’s limit states. This means that under low seismic excitation, the crane might be derailed without any structural damage. But when the crane reaches the minor damage state, it is always coupled with a certain probability of uplift with or without derailment. This study also proposes the fragility curves developed for different structural periods to enable port stakeholders to assess the risk of their container crane.

Optical coherence tomography (OCT) can help in the diagnosis and treatment of infectious keratitis, but it has not been studied in cases occurring after corneal refractive surgery procedures such as femtosecond laser in situ keratomileusis (FS-LASIK) and keratorefractive lenticule extraction (KLEx). In these procedures a surgical interface is created, where infections usually start, thus determining a different OCT pattern compared to non-surgical infections, which instead begin in the corneal surface. A total of 4 cases of post-refractive surgery infectious keratitis are reported (2 after FS-LASIK and 2 after KLEx), in which the OCT identified an initial infiltrate in the interface, followed by interface inflammation. In 1 case after FS-LASIK, interface fluid accumulation occurred. In 1 case after KLEx, diffuse interface inflammation led to stromal reabsorption, later compensated by stromal reformation and epithelial hyperplasia, well documented by OCT.

(1) Background: To determine the diagnostic accuracy that optical coherence tomography (OCT) can add to fundus photography (FP) in assessing the condition of the retinal posterior pole; (2) Methods: Two blocks of analysis: at first, the posterior pole of each eye was examined using FP non-mydriatic imaging device. Secondly: OCT was used in addition to FP. After consolidating specific diagnostic criteria, the assessments were evaluated by two blinded independent investigation groups (by optometrists, and by ophthalmologists who was considered the gold standard); (3) Results: We calculated the diagnostic accuracy of FP compared to OCT and found that both had similar sensitivity, FP had slightly higher specificity, (p-value: 0.01) and OCT had a higher kappa coefficient 0.50 (95%CI: 0.46-0.55) vs 0.39 (95%CI: 0.34-0.45) of FP; (4) Conclusions: Based on the premise that the role of the optometrist in Spain is not to diagnose but to detect lesions and refer patients to an ophthalmologist, the results of this study support the use of OCT, that it provided gradable images in almost all examined eyes (97.5%), compared to FP (73.5%). However, the optometrist need a detailed and standardized guide in order to evaluate according to the ophthalmologist's criteria.

Practical entanglement distillation is a critical component in quantum information theory. Entanglement distillation is often utilized for designing quantum computer networks and quantum repeaters. The practical entanglement distillation problem is formulated as a bilevel optimization problem. A fuzzy formulation is introduced to estimate the quantum state (density matrix) from pseudo-likelihood functions (i.e., quantum state tomography). A scale-independent relationship between fuzzy relations in terms of the pseudo-likelihood functions is obtained. The entanglement distillation optimization problem was solved using the combined coupled map lattice and dual annealing approach. Comparative analysis of the results is then conducted against a standard dual annealing algorithmic implementation.

Animal models of Alzheimer’s disease amyloidosis that recapitulate cerebral amyloid-beta pathology have been widely used in preclinical research, and have greatly enabled the mechanistic understanding of Alzheimer’s disease and the development of therapeutics. Comprehensive deep phenotyping of the pathophysiological and biochemical features in these animal models are essential. Recent advances in positron emission tomography have allowed the non-invasive visualization of the alterations in the brain of animal models as well as in patients with Alzheimer’s disease, These tools have facilitated our understanding of disease mechanisms, and provided longitudinal monitoring of treatment effect in animal models of Alzheimer’s disease amyloidosis. In this review, we focus on recent positron emission tomography studies of cerebral amyloid-beta accumulation, hypoglucose metabolism, synaptic and neurotransmitter receptor deficits (cholinergic and glutamatergic system), blood-brain barrier impairment and neuroinflammation (microgliosis and astrocytosis) in animal models of Alzheimer’s disease amyloidosis. We further propose the emerging targets and tracers for reflecting the pathophysiological changes, and discuss outstanding challenges in disease animal models and future outlook in on-chip characterization of imaging biomarkers towards clinical translation.

We present progress in fast, high-resolution imaging, material classification, and fault detection using hyperspectral X-ray measurements. Classical X-ray CT approaches rely on data from many projection angles, resulting in long acquisition and reconstruction times. Additionally, conventional CT cannot distinguish between materials with similar densities. However, in additive manufacturing, the majority of materials used are known a priori. This knowledge allows to vastly reduce the data collected and increase the accuracy of fault detection. In this context, we propose an imaging method for non-destructive testing of materials based on the combination of spectral X-ray CT and discrete tomography. We explore the use of spectral X-ray attenuation models and measurements to recover the characteristic functions of materials in heterogeneous media with piece-wise uniform composition. We show by means of numerical simulation that using spectral measurements from a small number of angles, our approach can alleviate the typical deterioration of spatial resolution and the appearance of streaking artifacts.

The technique of Faraday tomography is a key tool for the study of magnetised plasmas in the new era of broadband radio polarisation observations. In particular, observations at metre-wavelengths provide significantly better Faraday depth accuracies compared to traditional cm-wavelength observations. However, the effect of Faraday depolarisation makes the polarised signal very challenging to detect at metre wavelengths (MHz frequencies). In this work, Faraday tomography is used to characterise the Faraday rotation properties of polarised sources found in data from the LOFAR Two-Metre Sky Survey (LoTSS). Of the 76 extragalactic polarised sources analysed here, we find that all host a radio-loud AGN. The majority of the sources (∼64%) are large FRII radio galaxies with a median projected linear size of 710 kpc and median radio luminosity at 144 MHz of 4 × 10^26 W/Hz. In several cases, both hotspots are detected in polarisation at an angular resolution of ∼20". One such case allowed a study of intergalactic magnetic fields on scales of 3.4 Mpc. Other detected source types include an FRI radio galaxy and at least 8 blazars. Most sources display simple Faraday spectra, however, we highlight one blazar that displays a complex Faraday spectrum, with two close peaks in the Faraday dispersion function.

The present study investigates the role of a simple inerter in supplemental devices for possible implementation in the matured seismic base isolation technique. Firstly, the response of the base-isolated structure with an optimally tuned mass damper-inerter (TMDI) is investigated to see the tuning effects. The time required to tune the TMDI was found to be significantly longer than the duration of a strong-motion earthquake. There was still a reduction in the response of the isolated structure, which is primarily due to the added damping and stiffness (ADAS) of TMDI and not because of the tuning effects. Hence, it is proposed that the corresponding ADAS of the TMDI be directly added to the isolation device. Secondly, the response of the base-isolated structures with the fluid inerter damper (FID) is studied. It was observed that the inerter of the FID does not influence the displacement variance of an isolated structure under broadband earthquake excitation. It implies that the response of the isolated structure with FID is primarily controlled by its counterpart fluid damper (FD). The performance of optimal TMDI, ADAS, FID, and FD to mitigate the seismic response of the flexible multi-story base-isolated structure under real earthquake excitations is also investigated. In terms of suppressing the displacement and acceleration responses of the isolated structure, it has been found that TMDI and ADAS perform similarly. Comparing the response of the isolated structure with FID and FD demonstrated that the inerter in the FID has detrimental effects on the isolated structures, in which the top floor's acceleration and base shear are substantially increased.

In general, the stone pagoda structures with discontinuous surfaces are vulnerable to lateral forces and are severely damaged by earthquakes. After the Gyeongju earthquake in 2016 and the Pohang earthquake in 2017, the earthquakes damaged numerous stone pagoda structures due to slippage, rotation and the separation of stacked stone. To evaluate seismic resistance of masonry stone pagoda structure, we analyzed the seismic behavior of stone pagoda structure using shaking table test. Shaking frequency, permanent displacement, maximum acceleration, rocking, and sliding were assessed. Responses to simulations of the Bingol, Gyeongju, and Pohang earthquakes based on Korean seismic design standard (KDS 41 17 00) were analyzed for return periods of 1,000 and 2,400 years. We found that the type of stylobate affected the seismic resistance of stone pagoda structure. When the stylobates were stiff, seismic energy was transferred from lower to upper regions of the stone pagoda, which mainly resulted in deformation of the upper region. When the stylobates were weak, earthquake energy was absorbed in the lower regions; this was associated with large stylobate deformations. The lower part of tower body was mainly affected by rocking, because the structural members were slender. The higher part of the stone pagoda was mainly affected by sliding, because the load and contact area decreased with height.

In this paper, optimum parameters of Tuned Mass Dampers (TMD) are considered to control the responses of 10-story shear building under harmonic loading and 22 set of seismic records of FEMA-P695. The criterion used to obtain the optimum parameters is to select mass ratio, the frequency (tuning) and damping ratio that would result in smallest lateral displacements. State-space equations of motion are presented to compute the structural responses by developing a MATLAB file. A 10-story shear building is presented as a case study to assess the effects of TMDs on the multi-story structures. The results indicate that using TMD can reduce structural responses up to the average 20% under earthquake excitation and up to 90% under harmonic loadings. TMDs are not always effective under any type of ground motion; therefore, being aware of the given location is significant to design TMDs properly.

Extraction of high-resolution surface waves is essential in surface-wave survey. Because reflections usually interfere with surface waves on X component in a multicomponent seismic exploration, it is difficult to extract dispersion curves of surface waves. The situation goes more serious when the frequencies and velocities of higher-mode surface waves are close to those of PS-waves. A method for surface-wave extraction is proposed based on the morphological differences between reflections and surface waves. Frequency-domain high-resolution linear Radon transform (LRT) and time-domain high-resolution hyperbolic Radon transform (HRT) are used to represent surface waves and reflections respectively. Then, the sparse representation problem based on the morphological component analysis (MCA) is built and optimally solved to obtain high-fidelity surface waves. An advantage of our method is its ability to extract surface waves when their frequencies and velocities are close to those of reflections. Furthermore, results of synthetic and field examples confirm that the proposed method can attenuate the distortion of surface-wave dispersive energy caused by reflections, which contributes to extracting accurate dispersion curves.

Most European cities are characterized by very large areas, often formed by buildings with low quality, from a series of point of view. The possibility of renovating them is strategic to improve both the quality of life and to the possibility of economic recovery for building companies. In the last decades, the attention of the scientific community has been addressed to the energy renovation, thanks to the strong activities of the European Community in this field. However, since a relevant part of the EC territory is at risk of earthquake, the possibility to combine both energy and seismic renovation actions may be strategic for many countries. In particular, Italy and Romania are linked by a common social tradition that springs from the Roman Empire. Nowadays, this link is stronger, thanks to common interests in social, cultural and business fields. Therefore, the investigation of possible synergies for seismic and energy renovation strategies may be really interesting for both countries. This paper represents the first step in this direction. After an overview of regulations and common practices for buildings with reinforced concrete structures, in both states, some key combined renovation interventions will be described and discussed, as well as advantages and perspectives of integrated renovation approaches.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

Abstract Purpose: To analyze the correspondence between refractive astigmatism and corneal astigmatism in pseudophakic eyes with non-toric intraocular lenses. Setting: Yeouido St. Mary hospital, Seoul, South Korea Design: Evaluation of a diagnostic test instrument. Methods: This retrospective study included 95 eyes of 95 patients. Corneal astigmatism was measured with an automated keratometer (RK-5, Canon) and Scheimpflug tomography (Pentacam HR, Oculus). Refractive astigmatism was compared to keratometric astigmatism (based on anterior corneal measurements only), Equivalent K Reading and total corneal astigmatism (both based on anterior and posterior corneal measurements). Vector analysis was carried out by Næser’s polar value method. The accuracy was defined as the average magnitude of the vectorial difference in astigmatism (DA). Each corneal measurement was optimized in retrospect by a multiple linear regression equation between refractive and corneal astigmatism. Results: Keratometric astigmatism overestimated with-the-rule (WTR) refractive astigmatism and underestimated against-the-rule (ATR) refractive astigmatism. Several measurements based on both corneal surfaces values did not show any statistically significant difference with respect to refractive astigmatism. The mean corneal astigmatism by total corneal refractive power (TCRP) at 4.0 mm (zone/pupil) produced the lowest mean arithmetic DA and the highest percentage of eyes with a DA ≤0.50 diopter. After optimization, the accuracies of automated KA and TCRP 4.0 mm (zone/pupil) were similar. Conclusions: Total corneal astigmatism measured by the Scheimpflug tomography at 4.0 mm zone centered on pupil, accurately reflects the refractive astigmatism in pseudophakic eyes. However, the accuracy of total corneal astigmatism is not different from automated KA after optimization.

Aim of the presented research was to develop an optical sensing system to investigate the demineralization process of the bones. Optical measurement techniques are widely used and increasingly adapted in biological and biomedical applications due to their non-destructive nature and safety. Optical examination of the bone condition could facilitate clinical trials and improve the safety of patients. The authors used a set of complementary methods: polarization-sensitive optical coherence tomography (PS-OCT) and Raman spectroscopy. To stimulate the process of demineralization and gradual removal of the hydroxyapatite, the test samples of chicken bones were placed into 10% acetic acid. Measurements were carried out in two series. The first one took two weeks with data acquired every day. In the second series, the measurements were made during one day at an hourly interval (after 1, 2, 3, 5, 7, 10, and 24 hours). Raman spectroscopy was used to evaluate the disappearance of the hydroxyapatite. The relation between the content of hydroxyapatite and images recorded using OCT was analyzed and discussed. Moreover, the polarization properties of the bones have been evaluated. Based on OCT images, the retardation angles of the bones have been calculated. This work presents a preliminary study on the mechanism of bone demineralization and confirms the potential of the applied optical methods.

It is important for researchers in material domain to reconstruct and visualize the microstructure of alloy, which helps discover morphologies and properties that can only be found in three dimensional and microscopic space. However, because of the limitation of state-of-the-art sensors, the internal microstructure of the material is not easy to obtain. In this paper, a novel automatic 3D reconstruction method is proposed using diffraction contrast tomography technology to capture the 3D microstructure of Al-La alloy. The pipeline of the proposed method starts from the imaging of Al-La alloy with the LabDCT technique from Carl Zeiss AG, which produces a sequence of 2D microstructure sections. Then, a segmentation algorithm based on superpixel and lifted multicut is proposed to extract the 2D microstructure in an image section. Finally, 2D segmentations are joined together to reconstruct and visulize the 3D microstructure. As a result, a novel morphology of Al-La alloy is recovered with both dendrite and lamellar morphologies. The proposed method has the advantage of the ability to losslessly recover the internal microstructure.

This paper presents the experimental and numerical study on a ductile beam-column connection between a composite reinforced concrete truss (CRCT) beam and Concrete Filled Tube (CFT) column subjected to bending and shear loads. Two experimental models with different beam-column joint testing schemes, extracted from the same prototype three-dimensional structure designed according to the rules of the capacity design provided by seismic code, were subjected to quasi-static cyclic tests by applying gravitational loads and the horizontal seismic force. The main objective of this paper is to verify the experimental ductile behavior of both specimens and to simulate the experimental global and local response by nonlinear static analysis considering different modelling approaches. The comparison between the experimental and numerical results highlights, for both models considered, the ductile and dissipative capacity of the connection system, designed following the criterion of the hierarchy of resistances proposed by the current Italian code. Different experimental setup showed similar results demonstrating the repeatability of the test and its reproducibility through the nonlinear numerical analysis.

In the current research work, electrical resistance tomography (ERT) was employed for crystallization process monitoring and visualization. A first-of-its-kind MATLAB-based interactive GUI application “ERT-Vis” is presented. Two case studies involving varied crystallization methods were undertaken. The experiments involving calcium carbonate reactive (precipitative) crystallization for the high conductivity solution-solute media and the cooling crystallization for sucrose crystallization representing the lower conductivity solution-solute combination were designed and performed. The software successfully provided key insights regarding the process progress in both crystallization systems. It could detect and separate the crystal agglomerations in the low as well as high conductivity solutions using visual analytics tools provided. The performance and utility of the software were studied using a software evaluation case study involving domain experts. Participant feedback indicated that ERT-Vis software helps in reconstructing images instantaneously, interactively visualizing, and evaluating the output of the crystallization process monitoring data.

Oncology has emerged as a crucial field of study and treatment in the domain of medicine. Computed tomography has gained widespread adoption as a radiological modality for the identification and characterisation of pathologies, particularly in oncology, enabling precise identification of affected organs and tissues. However, achieving accurate liver segmentation in computed tomography scans remains a challenge due to the presence of artefacts and the varying densities of soft tissues and adjacent organs. This paper compares artificial intelligence algorithms and traditional medical image processing techniques to assist radiologists in liver segmentation on computed tomography scans, and evaluates their accuracy and efficiency. It is noteworthy that although studies have been conducted on liver segmentation in computed tomography scans, they often lack an intuitive and visual component that allows healthcare professionals to manipulate and observe the results obtained, thereby limiting interaction with the outcomes. From the literature review, challenges such as under-segmentation, over-segmentation, and poor boundary detection, as well as the selection of methods to improve the accuracy and efficiency of liver segmentation in computed tomography scanners, are highlighted as needs to be addressed. The importance of future research in understanding the essential features for the study, generating more datasets, improving segmentation efficiency, and developing lightweight artificial intelligence frameworks for liver segmentation is outlined.

This study aimed to estimate scattered radiation and its spatial distribution around three Cone Beam Computed Tomography (CBCT) devices, in order to determine relatively safe positions for an operator to stand if needed to be inside the CBCT room. The following devices were tested: Morita Accuitomo (CBCT1), Newtom Giano HR (CBCT2), Newtom VGi (CBCT3). Scattered radiation measurements were performed using different kVp, mA and Field of View (FOV) options. An anthropomorphic phantom (NATHANIA) was placed inside the x-ray gantry to simulate clinical conditions. Scattered measurements were taken with the ionization chamber Inovision model 451P Victoreen once placed at fixed distances from each irradiation isocenter, away from the primary beam. A statistically significant (p<0.001) difference was found in the mean value of the scattered radiation estimations between the CBCT devices. Scattered radiation was reduced with a different rate for each CBCT device as distance was increased. For CBCT1 the reduction was 0.047μGy, for the CBCT2 0.036 μGy and 0.079 μGy for CBCT3, for every one meter away from the x-ray gantry. Therefore, at certain distances from the central x-ray, the scattered radiation was below the critical 1mGy. Consequently, an operator could stay inside the room accompanying the patient being scanned, if necessary.

OCTA is an imaging modality used in the assessment of the retinal vasculature. It operates on the principle of coherence tomography used in standard OCT with the addition of delineating the retinal vascular. This provides a modern non-invasive retinal vascular imaging method compared to conventional dye-based imaging. High quality depth resolution of the superficial and deep capillary networks is possible on OCTA whereas this was not possible prior. OCTA may be limited by image quality degradation from factors such as motion artefact or media opacities, and therefore may not be the investigation of choice for all patient groups. There are multiple potential clinical applications for OCTA in retinal and choroidal vascular disease. Ongoing research is necessary to substantiate the more widespread use of OCTA due to its significant cost burden compared to current modalities.

A better study of the postnatal retinal development is not only essential for the in-depth understanding of the nature of the vision system but also may provide insights for treatment developments of eye conditions, such as retinopathy of premature (ROP). To date, quantitative analysis of postnatal retinal development is primarily limited to endpoint histological examination. This study is to validate in vivo optical coherence tomography (OCT) for longitudinal monitoring of postnatal retinal development in developing mouse eyes. Three-dimensional (3D) frame registration and super averaging were adopted to investigate the fine structure of the retina. Interestingly, a hyporeflective layer (HRL) between the nerve fiber layer (NFL) and inner plexiform layer (IPL) was observed in developing eyes and gradually disappeared with aging. To interpret the observed retinal layer kinetics, a model based on eyeball expansion, cell apoptosis, and retinal structural modification was proposed.

Optical coherence tomography (OCT) is one of the most promising, innovative and rapidly emerging intraoperative imaging modalities for neurosurgical guidance in brain tissue imaging, "optical biopsy", brain cerebral vascular detection, nerve fibers and white matter tracts detection. In this article, we provide a short survey of cross-polarization OCT and different types of OCT probes that can be used in routine neurosurgical practice. Through different types of probes there are multiple applications where OCT can play a highly complementary role in offering the real-time microscopic assessment and imaging of normal and pathological brain tissues. The biopsy-needle based probe for CP OCT was shown to be an effective instrument for brain tissue mapping and express estimation of tissue status as well as for detecting large blood vessels to prevent causing bleeding during biopsy sampling. The folded CP OCT probe for intraoperative use for brain tissue examination was shown as a potentially efficient sensor head for CP OCT. The probe demonstrated high lateral resolution in diffractive limited probing beam quality. The length of dismountable probe tip allows using the probe under operating microscope. Due to the designed family of specialized probes CP OCT fills in the niche of devices for express brain tissue examination in situ.

The paper highlights the performance of the seismic isolation devices, installed on retrofitted buildings in reducing the seismic response when subjected to earthquakes. Two buildings from the beginning of the XX-th century in Bucharest are chosen from many more, monitored over the city area. We discuss the response of these base-seismic isolated structures, relying on good quality data acquired from the recent strong earthquake (03.11.2022, MW = 5.0). Elastic response spectra computed from recordings at two levels of each structure are used, placed under and right above the isolating layer. At one building the existence of previous recordings and the particularity of the sensors allow a comparison with other two relatively recent medium intensity earthquakes. The assessment is carried out in terms of maximum acceleration amax, measured at certain levels in each structure, spectral acceleration amplitude SAmax and spectral-peak corresponding period. We find that the base-isolation methodology is effective in reducing the response of the building right above the isolating layer, an observation valid for both structures, all components of the recordings, and spectral acceleration values. Moreover, the outcomes from the modal evaluation performed prior to rehabilitation and seismic isolation process are presented, by pointing out a higher newly acquired fundamental period of the isolated structures.

Non-compliant (NC) structures are often encountered in building construction in developing countries. This is a condition whereby erected buildings do not follow regulatory standards, especially in the provision of reinforcements. Therefore, under an earthquake load, the structures do not have sufficient resistance against such load. The structural elements of the building, which often have NC conditions, are the beam-column joints because they do not contain adequate shear reinforcements due to installation difficulty. This study aims to determine the structural performance of the reinforced concrete (RC) frame, which has a reinforcement deficiency in the beam-column joints. Numerical simulation was conducted on the Kakaletsis structure model by modifying the reinforcement details at the joints to represent the NC conditions. The non-linear modeling and analysis of the structural model were carried out using ATENA software. The analysis showed that the reduction in shear reinforcements in the NC model joint caused a decrease in load-carrying capacity by about 26.04%. A shift was also observed in the collapse pattern, i.e., from the beam to the end of the column, causing global failure and reducing the undamaged but increasing more severely damaged condition. This showed that the NC structure, due to the non-conformance of reinforcement, significantly reduced the structure's performance.

This study introduces a new procedure for three-component spectral matching of seismic ground acceleration records. The procedure involves preserving the phase angle and varying the Fourier amplitudes to match the spectra of the recorded records with a provided target spectrum that represents the spectral values of ground motions in three orthogonal directions. Several three-component recorded records were matched against two target response spectra to test the method. An accurate convergence was achieved in the velocity and displacement records. In addition, the scales among the components’ magnitude were maintained, creating realistic three-component ground motions. Such ground motion inputs are important to qualify critical structures sensitive to three-component motions. Our proposed procedure is novel because the present practices are mostly created based on one-component ground motions.

Ultra-wide field optical coherence tomography (UWF-OCT) has been recently introduced into clinical ophthalmological practice. To date, there is little data on the reference values of retinal thickness (RT) and choroidal thickness (CT) measured with this technique. This study aimed to analyze the variance of RT and CT in healthy eyes with UWF-OCT tests performed with the largest available scan size of 23 x 20 mm. The data were analyzed with reference to the patients' age, gender, and the axial length of the eyeball. The results of UWF-OCT scanning enabled us to picture the shape of the retina and choroid in a large portion of the eyeball. Both anatomical entities become significantly thinner at the periphery. The peripheral CT is greater in the upper and temporal sectors; the RT is higher in the nasal compared to the temporal sectors. Both choroid and retina lose thickness with age, however, CT and RT do not show a statistically significant correlation with the axial length after adjusting for age and gender. Age-related variations in thickness are especially prominent in the choroid. The CT in UWF-OCT testing is significantly greater in females while the RT is greater in males. UWF-OCT testing provides additional information on the anatomical structure of the retina and choroid compared to standard-field OCT

This article aims to detect lung cavitations using lung ultrasound (LUS) in a cohort of patients with pulmonary tuberculosis (TB) and correlate the findings with chest computed tomography (CT) and chest x-ray (CXR) to obtain LUS diagnostic sensitivity. Patients with suspected TB were enrolled after being evaluated with CXR and chest CT. A blinded radiologist performed LUS within 3 days after the admission at the Infectious Diseases Department. Finally, 82 patients were enrolled in the study. BAL confirmed TB in 58/82 (71%). Chest CT showed pulmonary cavitations in 38/82 (43.6%; 32 TB patients and 6 non-TB ones), LUS in 15/82 (18.3%; 11 TB patients and 4 non-TB ones) and CXR in 27/82 (33%; 23 TB patients and 4 non-TB ones). Patients with multiple cavitations were 12 detected at CT and only 1 at LUS. LUS sensitivity was 39.5%, specificity 100%, PPV 100%, NPV 65.7%. CXR sensitivity was 68.4% and specificity 97.8%. No false positive cases were found. LUS sensitivity is rather low as many cavitated consolidations do not reach the pleural surface. Aerated cavitations could be detected with LUS with relative confidence, highlighting a thin air-crescent sign towards the pleural surface within a hypoechoic area of consolidation, easily distinguishable from dynamic or static air-bronchogram.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.

The article presents the results of research on a new method of spatial analysis of walls and buildings moisture. Due to the fact that destructive methods are not suitable for historical buildings of great architectural significance, a non-destructive method based on electrical tomography has been adopted. A hybrid tomograph with special sensors was developed for the measurements. This device enables the acquisition of data, which are then reconstructed by appropriately developed methods enabling spatial analysis of wet buildings. Special electrodes that ensure good contact with the surface of porous building materials such as bricks and cement were introduced. During the research, a group of algorithms enabling supervised machine learning was analyzed. They have been used in the process of converting input electrical values into conductance depicted by the output image pixels. The conductance values of individual pixels of the output vector made it possible to obtain images of the interior of building walls, both flat intersections (2D) and spatial (3D) images. The presented group of algorithms has a high application value. The main advantages of the new methods are: high accuracy of imaging, low costs, high processing speed, ease of application to walls of various thickness and irregular surface. By comparing the results of tomographic reconstructions, the most efficient algorithms were identified.

This paper provides a comparative study between microwave tomography and synthetic time-reversal imaging techniques as applied to ground penetrating radar (GPR) surveys. The comparison is carried out by processing experimental data collected at a controlled test site, with various types of buried targets at given subsurface depths and representative soil conditions. It is shown that the two techniques allow us to obtain complementary information about position, depth and size of the targets from a single GPR survey.

Understanding and improving seismic resilience in regions prone to earthquakes is crucial for mitigating the effects of natural disasters. This study zeroes in on Montenegro, a region frequently affected by seismic activity, with the goals of critically evaluating current resilience levels, pinpointing key preparedness gaps, and assessing the efficacy of existing response strategies. Employing qualitative methods, the research involved semi-structured interviews with residents from Montenegro's most vulnerable areas, including Nikšić, Podgorica, Bar, Kotor, Cetinje, Budva, Herceg Novi, and Berane. These participants, selected for their firsthand experiences with significant earthquake impacts, contributed to a deeper understanding through discussions that aligned with a broad conceptual framework, exploring everything from the nuances of citi-zen resilience to local government responses and personal preparedness. The study aimed to gather in-depth views on community resilience during earthquakes, evaluate citizens' knowledge and preparedness for such disasters, and examine local governance strategies for enhancing seismic resilience. It revealed varying resilience levels across communities, with some displaying well-structured strategies while others showed notable deficiencies. The findings underscore the urgent need for community-specific preparedness programs and improvements in both structural and educational frameworks to enhance resilience. This research highlights the necessity of a comprehensive approach that includes detailed risk assessments, tailored preparedness training, and stronger public awareness efforts. Additionally, it emphasizes strengthening local governments' capabilities to enact and sustain effective response measures to ensure ongoing community resilience against future seismic challenges.

In this study, three new demountable joints consisting of reinforced concrete columns and steel beams were proposed and their seismic performance was investigated using cyclic loading tests. The test results demonstrated that the three demountable RCS joints had good seismic performance. Using the finite element software ABAQUS, the influence of parameters such as beam flange thickness, bolt strength, and connector steel strength on the seismic performance of each joint was analyzed, and the influence of different parameters on the seismic behavior of the joint was determined. The results also showed that the three demountable RCS joints were sensitive to changes in the thickness of the steel beam flange, while the connector steel strength and bolt type had little impact on the joint's capacity. Additionally, shear capacity calculation formulas for the joint core area provided by different codes and researchers were compared with test and finite element results. The results showed that the calculation results of the ASCE guidance method, the Nishiyama method, and the CECS 347-2013 method were higher than the test values, while the calculation results of the Para method were lower because it did not consider the contribution of the cylindrical steel plate to the shear capacity of the joint core area.

Confined masonry (CM) is a construction system which consists of masonry wall panels enclosed by vertical and horizontal reinforced concrete confining elements. The presence of these confining elements distinguishes CM from unreinforced masonry system and makes this technology suitable for construction of structures in regions subjected to intense seismic or wind actions. CM construction has been used in many countries and regions, and has performed well in past earthquakes. The purpose of the paper is to review past research studies related to the seismic in-plane and out-of-plane behaviour of CM structures. The authors have identified the key design and construction parameters which were considered in past research studies and have performed statistical analyses to establish their influence on the seismic performance of CM buildings. For the purpose of this study the authors have compiled databases of previous experimental studies on CM wall specimens which were used for statistical analyses. Finally, the paper discusses research gaps and needs for future research studies which would contribute to the understanding of seismic behaviour and failure mechanisms of CM walls.

Nepal is one of the most seismically active regions in the world, as highlighted by the recent devastating 2015, Mw7.8 Gorkha earthquake and a robust assessment of seismic hazard is paramount for the design of earthquake-resistant structures. In this study we present a new probabilistic seismic hazard assessment (PSHA) model for Nepal. We considered data and findings from recent scientific publications, which allowed us to develop a unified homogenized seismicity catalogue, propose alternative Seismic Source Characterization (SSC) models including up-to-date parameters of major thrust faults like Main Frontal Thrust – MFT and Main Boundary Thrust – MBT, while also considering existing SSC models and various hazard modelling strategies within a logic tree framework. The sensitivity analyses show the hazard levels are generally higher for SSC models integrating the major thrust faults, followed by homogenous volume sources and smoothed seismicity approach. The hazard maps covering entire Nepal is presented as well as the Uniform Hazard Spectra (UHS) for 5 selected locations (Kathmandu, Pokhara, Biratnagar, Nepalganj and Dipayal) at return periods of 475- and 2,475-years considering Vs,30=760 m/s. The results obtained are generally consistent with most recent studies. However, a notable variability in hazard levels and several discrepancies with respect to the Nepal Building Code NBC105: 2020 [1] and Global Hazard Model, GEM [2] are noted and possible causes are discussed.

The steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings, and those used for multistory housing in particular. However, the effectiveness of steel damper columns may be affected by the behavior of surrounding members, and this effect can be severe in the case of seismic sequences. This article investigates the nonlinear response of building models having an RC moment-resisting frame (MRF) with and without steel damper columns under seismic sequences. The applicability of the concept of the momentary energy input to the prediction of the peak response of RC MRFs with damper columns under seismic sequences is also investigated. The main findings of the study are summarized as follows. (1) The peak response of RC MRFs with damper columns subjected to sequential accelerations is similar to the peak response obtained considering only the mainshock, whereas the cumulative strain energy of RC MRFs accumulates more for sequential accelerations. (2) The steel damper column is effective in reducing the peak and cumulative responses of RC MRFs in the case of sequential seismic input. (3) The relation of the hysteretic dissipated energy during a half cycle of the structural response and the peak displacement of the first modal response can be properly evaluated using the simple model proposed in this study.

Rapid post-earthquake damage diagnosis of bridges can guide decision-making for emergency response management and recovery. This can be facilitated using digital technologies to remove the barriers of manual post-event inspections. Prior mechanics-based Finite Element (FE) models can be used for post-event response simulation using the measured ground motions at nearby stations; however, the damage assessment outcomes would suffer from uncertainties in structural and soil material properties, input excitations, etc. For instrumented bridges, these uncertainties can be reduced by integrating sensory data with prior models through a model updating approach. This study presents a sequential Bayesian model updating technique, through which a linear/nonlinear FE model, including soil-structure interaction effects, and the foundation input motions are jointly identified from measured acceleration responses. The efficacy of the presented model updating technique is first examined through a numerical verification study. Then, seismic data recorded from the San Rogue Canyon Bridge in California are used for a real-world case study. Comparison between the free-field and the foundation input motions reveals valuable information regarding the soil-structure interaction effects at the bridge site. Moreover, the reasonable agreement between the recorded and estimated bridge responses shows the potentials of the presented model updating technique for real-world applications. The updated FE model is considered as the digital twin of the bridge and can be used to analyze the bridge and monitor the structural response at element, section, and fiber levels to diagnose the location and severity of any potential damage mechanism.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Background: Electrical Impedance Tomography (EIT), combined with variable ventilation strate-gies and Artificial Intelligence (AI), is poised to revolutionize critical care by transitioning from reactive to predictive approaches. This integration aims to enhance patient outcomes through personalized interventions and real-time monitoring. Methods: This narrative review explores the principles and applications of EIT, variable ventilation, and AI in critical care. EIT’s impedance sensing creates dynamic images of internal physiology, aiding in the management of conditions like Acute Respiratory Distress Syndrome (ARDS). Variable ventilation mimics natural breathing variability to improve lung function and minimize ventilator-induced lung injury. AI enhances EIT through advanced image reconstruction techniques, neural networks, and digital twin technology, offering more accurate diagnostics and tailored therapeutic interventions. Conclu-sions: The confluence of EIT, variable ventilation, and AI represents a significant advancement in critical care, enabling a predictive, personalized approach. EIT provides real-time insights into lung function, guiding precise ventilation adjustments and therapeutic interventions. AI inte-gration enhances EIT's diagnostic capabilities, facilitating the development of personalized treatment plans. This synergy fosters interdisciplinary collaborations and sets the stage for in-novative research, ultimately improving patient outcomes and advancing the future of critical care.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

This article introduces a new MfEIT UDESC Mark I system, which consists of a 32-electrode setup featuring a modified Howland current source, low cost, portable and non radiation. The system is capable of reconstruction of electrical conductivity tomographic images at a rate of 30.624 frames per second and about 5 minutes for imaging. The current source employs 0.5 mA, adjacent current application pattern with frequencies ranging from 10 kHz to 1 MHz. The article outlines the hardware, firmware, and software design specifications, which include the design of the current source, calibration procedures, and image reconstruction process. Tomographic images of conductivity were reconstructed in ex vivo healthy pig lungs and those with pneumonia, as a proof of concept for future applications in live pigs. The high spectral power density, combined with real-time system calibration provides clinical advantages in veterinary medicine. The goal is to identify lung areas affected by Mycoplasma hyopneumoniae in pigs, through the analysis of electrical conductivity difference, offering a valuable tool to assist veterinarians for to obtain images of respiratory diseases. The reconstruction method (GREIT) was evaluated with experimental data and It was compared with the Gauss-Newton and Total Variation methods, where GREIT proved to be superior.

Fractures of the talar neck and body are associated with spine fractures and scoliosis deformity, which affect cosmetic appearance and cause difficulty in ambulation. The implant design for talus surgery is thriving as a functional alternative in case of severe talar destruction, focusing on segmentation and reconstruction of the talus’s shape. However, manual segmentation of the talus is time-consuming and subjective. In this study we exploited the automatic segmentation framework to efficiently train a deep learning-based model to accurately segment the talus based on computed tomography imaging. We developed three model configurations with nnU-Net and investigated their Dice similarity coefficients (DSC) and 95% Hausdorff distances (HD95) for talus segmentation on a CT image dataset. The three configurations performed well (DSC > 0.95, HD95 < 0.6). When tested on the same samples, one of the configurations was more efficient while ensuring higher accuracy. We propose to focus on talus anatomic variations with increasing age based on this framework and apply it to clinical trials at the next stage.

Introduction: CT perfusion (CTP) is an alternative tool to assess cerebral hemodynamics in brain trauma. As traumatic acute subdural hematomas (ASH) are severe lesions commonly associated with poor outcome, we aimed to evaluate the brain hemodynamics in this population. Methods: Five patients admitted at the emergency department sustaining traumatic acute subdural hematoma were evaluated. Preoperative CTP was performed immediately after nonenhanced head CT scan. Postoperative CTP was performed in four patients. The outcome was assessed 6 months after surgery using the extended Glasgow Outcome Scale. Results: 4 male and 1 female were evaluated. Mean age was 46y (SD: 8.1). Mean preoperative midline brain shift was 10.1 mm (SD: 1.8). The main mechanism of trauma was falling (four patients). There was a general improvement in cerebral blood flow (CBF) after surgery from 23.9 (SD: 6.1) to 30.7 ml/100g/min, (SD: 5.1) and in mean transit time (MTT) from 7.3 (SD: 1.3) to 5.8s (SD:1.0), although it is not statistically significant (p=0.06 and p=0.06, respectively). There was still a reduction in the cerebral blood volume (CBV) media when compared to the value after surgery, from 2.63 (SD: 1.10) to 2.34 ml/100g (SD: 0.67), which is not statistically significant (p=0.31). Spearman correlation test of postoperative and preoperative CBF ratio with outcome was 0.94 (p=0.054). Only one patient died (three days after surgery). This patient was victim of car crash and had the highest preoperative MTT (9.97 seconds) and CBV (4.51 ml/100 g). Conclusion: Post-operative improvement of hemodynamic CTP parameters may be correlated with outcomes after ASH. Further studies with larger samples are required to confirm this hypothesis.

The ever-growing field of materials with applications in the biomedical field holds great promise regarding the design and fabrication of devices with specific characteristics especially scaffolds with personalized geometry and architecture. The continuous technological development pushes the limits of innovation in obtaining adequate scaffolds and establishing their characteristics and performance. To this end, computed tomography (CT) proved to be a reliable, non-destructive, high-performance machine, enabling visualization and structure analysis at sub-micronic resolutions. CT allows both qualitative and quantitative data of the 3D model, offering an overall image of its specific architectural features as well as reliable numerical data for rigorous analyses. The precise engineering of scaffolds consists in the fabrication of objects with well-defined morphometric parameters (e.g.: shape, porosity, wall thickness), and in their performance validation through thorough control over their behavior (in situ visualization, degradation, new tissue formation, wear, etc.). This review is focused on the use of CT in biomaterial science with the aim of qualitatively and quantitatively assess the scaffolds’ features and in monitoring their behavior following in vivo or in vitro experiments. Furthermore, the paper presents the benefits and limitations regarding the employment of this technique when engineering materials with applications in the biomedical field.

Several studies suggest that COVID-19 may be accompanied by symptoms such as a dry cough, muscle aches, sore throat, and mild to moderate respiratory illness. The symptoms of this disease indicate the fact that COVID-19 causes noticeable negative effects on the lungs. Therefore, considering the health status of the lungs using X-rays and CT scans of the chest can significantly help diagnose COVID-19 infection. Due to the fact that most of the methods that have been proposed to COVID-19 diagnose deal with the lengthy testing time and also might give more false positive and false negative results, this paper aims to review and implement artificial intelligence (AI) image-based diagnosis methods in order to detect coronavirus infection with zero or near to zero false positives and false negatives rates. Besides the already existing AI image-based medical diagnosis method for the other well-known disease, this study aims on finding the most accurate COVID-19 detection method among AI methods such as machine learning (ML) and artificial neural network (ANN), ensemble learning (EL) methods.

The aim of the study was to compare the standard baseline imaging, with extended radiological staging. To assess our hypothesis, we performed a prospective, single-centre study which included 132 participants recruited between October 2015 and March 2020. Descriptive statistics, the Friedman and chi-squared tests were performed and p &lt; 0.05 was considered significant. Patients were grouped into two cohorts, CT scan cohort (n=87) and PET-CT cohort (n=43). In the first group the originally determined disease stage changed in 36.8 % of cases, in second group in 51.2 %. The consistency between assessment of axillary lymph nodes by imaging (cN) and the postoperative pathology report (pN) was evaluated. In most cases, clinical and pathological evaluation of involved nodes was consistent, for CT scan the result was χ2(1) = 18.98; p &lt; 0.001, for PET-CT the result was χ2(1) = 6.41; p = 0.03. Highly customized radiation therapy defined as dose boost within the involved lymph nodes, not covered by surgeon, was applied in nine patients.

Coronary angiography, long considered the gold standard for coronary imaging, faces limitations in assessing coronary vessel wall anatomy and guiding percutaneous coronary intervention (PCI). Despite its prevalence, studies have demonstrated that it is suboptimal in estimating the severity of coronary disease and physiologic significance of stenosis. Intracoronary imaging techniques, such as intravascular ultrasound (IVUS) and optical coherence tomography (OCT), offer promising alternatives to overcome these limitations. This review delves into the nuances of IVUS and OCT, highlighting their strengths and limitations as adjuncts to PCI. IVUS, utilizing ultrasound technology, and OCT, based on near-infrared light, each provide unique insights into coronary pathology. They differ in terms of temporal and spatial resolution, influencing their capabilities in plaque characterization and vessel assessment. The discussion navigates their historical evolution, technical specifications, and clinical utility. Meta-analyses and adjusted observational studies suggest that both IVUS and OCT-guided PCI correlate with reduced cardiovascular risks compared to angiographic guidance alone. While IVUS has demonstrated consistent benefits in terms of clinical outcomes, the evidence supporting OCT is less robust. However, the utilization of these imaging modalities remains variable across regions, with increasing adoption in recent years, particularly in IVUS-guided PCIs. Intravascular ultrasound's journey from early motion detection to current high-resolution mechanical systems is traced, including improvements in catheter size and compatibility. On the other hand, optical coherence tomography has advanced significantly, utilizing near infrared light to achieve unparalleled resolutions, albeit requiring temporary blood clearance for optimal imaging. In conclusion, IVUS and OCT offer valuable insights into coronary pathophysiology and guide interventions with improved precision compared to traditional angiography. While IVUS remains more extensively utilized, OCT's growing potential is underscored by advancements in technology, culminating in enhanced imaging capabilities. Both modalities demonstrate comparable clinical outcomes, emphasizing the need for tailored imaging choices based on individual clinical scenarios. The continued refinement and broader integration of intravascular imaging are expected to play a pivotal role in optimizing coronary interventions and patient outcomes.

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

Background: As coronavirus (COVID-19) continues to pose a threat to the entire world, it is critical to developing strategies for containing its spread. The purpose of this study was to assess the demographic characteristics, brain tomography characteristics, and diffusion magnetic resonance findings of COVID-19 positive individuals. Material and Method: Between January 1 and December 31, 2021, 317 patients over the age of 18 were admitted to the emergency department with symptoms consistent with COVID-19. Three groups were formed based on clinical findings in patients, divided into light, medium, and severe, and four groups were formed based on radiological imaging findings. Results: The mean age of the 317 patients included in the study was 67.28±12.06 years, with a range of 28-91 years. The clinical classification of the patients was based on laboratory parameters and radiological imaging, not on their age or gender. Mild cases were classified as CO-RADS 0-4; moderate and severe cases were classified as CO-RADS 5-6 (p=0.001). While 60 (18.9%) of patients were followed outpatient, 144 (45.4%) were admitted to the hospital, 73 (23%) were admitted to the intensive care unit, and 40 (12.7%) died (p=0.001). Direct radiographs revealed bilateral involvement in 224 (70.7%) cases, peripheral involvement in 259 (81.7%) cases, and mid-lower lobe lung involvement in 194 (61.2%) cases (p=0.001). Brain tomography revealed infarction in 42 (13.2%) of the patients who were followed and hospitalized and hemorrhage in 22 (6.9%) of the patients. Magnetic resonance imaging revealed diffusion involvement in 68 (21.5%) of the cases (p=0.001). Conclusion: A standardized reporting system for COVID-19 data is required, and it must be simple to use, quick to understand, and focused on determining the risk of pneumonia. Additionally, the diagnostic role of radiological imaging, prognosis prediction, and severity scoring of lung involvement should be included.

With the Sendai Framework (2015-2030) and the Paris Agreement (2015), the UN has been promoting at a global level, the priority objectives to protect the life and well-being of people, these documents of global consensus have scheduled in several countries, an extensive list of actions of responsibilities and commitments to the environment, to address natural disasters among those of greatest impact earthquakes and floods and among earthquakes (seismic activity). The materialization of the disaster is a natural or human-induced event, it manifests itself in permanent changes in society and by its origin it is classified as natural, anthropogenic (anthropogenic) and mixed, creating a worldwide problematic situation of immediate reaction. The attention and alert in the scientific community have been adding efforts, but in a disorganized way, with limited human and material resources and with globalized strategies still to be improved. The literature review of disaster risk management due to seismic activity, from 2008 to 2023, allows us to have updated information to identify the factors and deepen them, with the understanding, comprehension, and multidisciplinary knowledge. The selected researches that mention the factors (elements) that influence risk management of natural disasters due to seismic activity (RMNDDSA) allow us to know the advances and spaces to approach them, which constitutes the motivation to study the twenty-four (24) factors present in this type of disasters. The selected research articles indicate important advances that associate disaster risk management (DRM) and communication technology (ICTs). The technological means mentioned are well received and accepted by society, capable of detecting and communicating in real time seismic activity worldwide, with the help of social mobile networks, technological platforms, Twitter, Facebook, and others.

To achieve rapid post-earthquake repair of self-centering ribbed floor flat beam frame structures, a ductile hybrid joint consisting of dog bone weakened energy dissipating steel bars connected to the upper and lower column sections through high-strength threads based on the damage control design concept is proposed. By moving the ductile energy dissipating zone out to the locally weakened section of the energy dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance was improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-consuming steel bars in the composite layer and the friction performance of joints. The research results indicated that the hybrid joint had stable load-bearing, deformation, and energy dissipation capabilities, with damage primarily concentrated on the energy-consuming steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with an increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint had excellent seismic performance and can also achieve post-earthquake repair of structures.

This paper presents an innovative approach for improving the seismic protection of existing structures by introducing an additional dissipative structure (ADS). The seismic energy impacting the building can be dissipated through the contribution provided by the ADS, thereby reducing the need for the existing building to ensure its seismic capacity. This retrofitting technique is well-suited for structures facing architectural restrictions or challenging-to-update elements. It can help address foundation issues by applying loads to new external components. This paper describes the design of the ADS and proposes a displacement-based design procedure. The design process involves a non-linear static analysis and a simple procedure that must be iteratively repeated until the retrofitting target is achieved. This approach is simple and computationally efficient and can also be used for complex and irregular structures. Such structures are frequently encountered, and existing structures often exhibit unusual geometries and materials requiring extensive numerical modeling. The efficacy of the technique was evaluated using the case studiy of a school building located in central Italy. The results of numerical analyses indicated that owing to the ADS’s contribution, the seismic capacity of both buildings was enhanced, addressing the challenges associated with complex foundation interventions.

Seismic vulnerability assessment in urban areas would in principle require the detailed modeling of each single building and the implementation of complex numerical calculations. This procedure is clearly difficult to apply at urban scale where many buildings have to be considered and therefore it is essential to have simplified, but at the same time reliable, approaches to vulnerability assessment. Among the proposed strategies, one of the most interesting concerns the application of machine learning algorithms, able to classify buildings according to their vulnerability on the basis of training procedures applied to existing datasets. In this paper machine learning algorithms will be applied to a dataset which collects and catalogs the structural characteristics of a large number of buildings and reports the damage observed in L’Aquila territory during the intense seismic activity occurred in 2009. A combination of a trained neural network and a random forest algorithm allows to identify an opportune “a-posteriori” vulnerability score, deduced from the observed damage, which is compared to an “a-priori” vulnerability one, evaluated taking into account characteristic indexes for building’s typologies. By means of this comparison an inverse approach to seismic vulnerability assessment, which can be extended to different urban centers, is proposed.

Landslide is one of the most common geological disasters in China, which is characterized by suddenness and uncertainty, and it is difficult to realize accurate identification, early warning and forecasting of landslide disaster by conventional means. With the development of high-resolution remote sensing satellites and InSAR surface deformation monitoring technology, the traditional means of landslide monitoring data sources are limited, and there is a lack of effective methods to excavate the characteristics of the spatial distribution of landslide hazards and their triggering factors and other issues. In this paper, the area extending 10 km outside the VII isobar of the Gengma earthquake is taken as the study area, and 13 evaluation factors are screened out by integrating the factors of InSAR surface deformation, topography and geological environment, and the Bayesian Optimized Convolutional Neural Network (BO-CNN) is used for the evaluation of landslide susceptibility, and the BO-RF and PSO-SVM models are selected for the comparative analysis. The model accuracy evaluation was carried out by three indexes: ROC curve, AUC value and FR value, in which the ROC curves of PSO-SVM, BO-RF and BO-CNN were all close to the upper-left corner of the corner, and the AUC values were 0.9388, 0.9529, and 0.9535, respectively, and the FR value of landslide in the high susceptibility area of BO-CNN was as high as 14.9, and was higher than that of PSO-SVM and BO-RF, respectively. SVM and BO-RF model is 4.55 and 3.69 higher, the experimental results show that the BO-CNN model used in this paper has a better effect in landslide susceptibility evaluation, and the research results of the local government's disaster prevention and mitigation measures are of great significance.

The information of seismic damage of buildings in SAR images of different time phase, especially in SAR images after earthquake, is easily disturbed by other factors, which affects the accuracy of information discrimination. In order to identify and evaluate the distribution information of the seismic damage accurately and make full use of the abundant texture features in the SAR image. The conventional method of change detection based on texture features usually takes the pixel as the calculating unit. In this paper, a method of texture feature change detection of SAR images based on watershed segmentation algorithm is proposed. Based on the optimization of texture feature parameters, the feature parameters are segmented by the watershed segmentation algorithm, and the feature object image is obtained. This method introduces the idea of object oriented, and carries out the calculation of the difference map at the object level, Finally, the classification threshold value of different types of seismic damage types is selected, and the recognition of building damage is achieved. Taking the ALOS data before and after the earthquake in Yushu as an example to verify the effectiveness of the method, the overall accuracy of the building extraction is 88.9%, Compared with pixel-based methods, it is proved that the proposed method is effective.

Landslides, resulting from disturbances in slope equilibrium, pose a significant threat to landscapes, infrastructure, and human life. Triggered by factors such as intense precipitation, seismic activities, or volcanic eruptions, these events can cause extensive damage and endanger nearby communities. A comprehensive understanding of landslide characteristics, including spatio-temporal patterns, dimensions, and morphology, is vital for effective landslide-disaster management. Existing Remote Sensing approaches mostly use either optical or Synthetic Aperture Radar (SAR) sensors. Integrating information from both these types of sensors promises greater accuracy for identifying and locating landslides. This study proposes a novel approach, the ML-LaDeCORsat (Machine Learning-based coseismic Landslide Detection using Combined Optical and Radar Satellite Imagery), that integrates freely available Sentinel-1, Palsar-2, and Sentinel-2 imagery data, along with relevant spectral indices and suitable bands using machine-learning-based classification for coseismic landslide detection implemented in Google Earth Engine (GEE). The approach includes a robust and reproducible training and validation strategy. Using landslides from four different earthquake case studies, we demonstrate the superiority of our approach over existing solutions in coseismic landslide iden-tification and localization, providing a detection accuracy of 87-92%. ML-LaDeCORsat can be adapted to other landslide events (GEE script is provided). Transfer learning experiments proofed that our model can be applied to other coseismic landslide events without the need for additional training data. Our novel approach therefore facilitates quick and reliable identification of co-seismic landslides, highlighting its potential to contribute towards more effective disaster management.

A quite energetic seismic excitation consisting of one main and additional three distinctive earthquake clusters that occurred in the transition area between the Kefalonia Transform Fault Zone (KTFZ) and the continental collision between Adriatic and Aegean microplates, is thoroughly studied after high–precision aftershocks’ relocation. The activated fault segments are in an area where historical and instrumental data have never claimed the occurrence of a catastrophic (M>6.0) earthquake. The relocated seismicity initially defines an activated structure extending from the northern segment of the Lefkada branch of KTFZ with the same NNE–SSW orientation and dextral strike-slip faulting and then keeping the same sense of motion its strike becomes NE–SW and its dip direction NW. This provides unprecedented information on the link between the KTFZ and the Collision front and sheds more light on the regional geodynamics. The earthquake catalog, which is specially compiled for this study, starts one year before the occurrence of the Mw5.4 mainshock and adequately provides the proper data source for investigating the temporal variation of the b–value, which might be used for discriminating foreshock and aftershock behavior.

This study presents an exploration into identifying the interactions between ocean waves and the continental margin in the origination of double-frequency (DF, 0.1-0.5 Hz) microseisms recorded at 33 stations across East Coast of USA (ECUSA) during a ten-day period of ordinary ocean wave climate. Daily primary vibration directions are calculated in three frequency bands and projected as great circles passing through each station. In each band, the great circles from all stations exhibit largest spatial density primarily near the continental slope in the western North Atlantic Ocean. Generation mechanisms of three DF microseism events are explored by comparing temporal and spatial variations of the DF microseisms with the migration patterns of ocean wave fronts in Wavewatch III hindcasts. Correlation analyses are conducted by comparing the frequency compositions of and calculating the correlation coefficients between the DF microseisms and the ocean waves recorded at selected buoys. The observations and analyses lead to a hypothesis that the continental slope causes wave reflection, generating low frequency DF energy and that the continental shelf is where high frequency DF energy is mainly generated in ECUSA. The hypothesis is supported by the primary vibration directions being mainly perpendicular to the strike of the continental slope.

Research shows that in earthquakes the ground response changes in areas where there are underground cavities. Due to the fact that subways and underground tunnels pass from beneath buildings in urban areas, these changes in ground response have a direct impact on the seismic behavior of structures. In this study, first by model validity and reliability of the results, steel structures modeling was conducted and steel structure behavior was evaluated due to Tunnel-Soil-Structure seismic interaction. Parameters studied are number of stories, soil type, tunnel depth, horizontal tunnel-structural distance and dynamic loading. Considering that one of the most important parameters of structural control is drift and story displacement, so this important factor will be considered. The results show that tunneling has a direct effect on the rate of structural displacement and increases the structural response. Also, the behavior of the structure is affected by the position of the structure at the ground level and the position of the tunnel and this should be considered during the design phase of the structures.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

Contrast agents developed for X-ray computed tomography (CT) offer extremely valuable tools and techniques in diagnostics via contrast enhancements. Heavy metal-based nanoparticles (NPs) can provide high contrast in CT images. These result from a high density of heavy metal atoms with high X-ray attenuation coefficients that exceed that of iodine (I), which is currently used in hydrophilic organic CT contrast agents. Nontoxicity and colloidal stability are vital characteristics in designing heavy metal-based NPs as CT contrast agents. In addition, the particle size must be small for in vivo renal excretion. In vitro phantom imaging studies can provide X-ray attenuation efficiency, which is a critical parameter for CT contrast agents, and the imaging performance of CT contrast agents can be demonstrated via in vivo experiments. This review focuses on in vitro and in vivo studies of various heavy metal-based NPs (metal: Au, Pt, Pd, Ag, Ce, Gd, Dy, Ho, Yb, Ta, W, and Bi) and provides an outlook on their use as high-performance CT contrast agents.

Coronary optical coherence tomography (OCT) is an intravascular, near-infrared light-based imaging modality capable of reaching axial resolutions of 10-20 µm. This resolution allows for accurate determination of high-risk plaque features, such as thin cap fibroatheroma; however, visualisation of morphological features alone still provides unreliable positive predictive capability for plaque progression or future major adverse cardiovascular events (MACE). Biomechanical simulation could assist in this prediction, but this requires extracting morphological features from intravascular imaging to construct accurate three-dimensional simulations of patients’ arteries. Extracting these features is a laborious process, often carried out manually by trained experts. To address this challenge, numerous techniques have emerged to automate these processes while simultaneously overcoming difficulties associated with OCT imaging, such as its limited penetration depth. This systematic review summarises advances in automated segmentation techniques from the past five years (2016-2021) with a focus on their application to the three-dimensional reconstruction of vessels and their subsequent simulation. We discuss four categories based on the feature being processed, namely: coronary lumen; plaque characteristics and subtypes; artery layers; and stents. Areas for future innovation are also discussed as well as their potential for future translation.

Early detection improves prognosis in pancreatic ductal adenocarcinoma (PDAC) but is challenging as lesions are often small and poorly defined on contrast-enhanced computed tomography scans (CE-CT). Deep learning can facilitate PDAC diagnosis, however current models still fail to identify small (&lt;2cm) lesions. In this study, state-of-the-art deep learning models were used to develop an automatic framework for PDAC detection, focusing on small lesions. Additionally, the impact of integrating surrounding anatomy was investigated. CE-CT scans from a cohort of 119 pathology-proven PDAC patients and a cohort of 123 patients without PDAC were used to train a nnUnet for automatic lesion detection and segmentation (nnUnet_T). Two additional nnUnets were trained to investigate the impact of anatomy integration: (1) segmenting the pancreas and tumor (nnUnet_TP), (2) segmenting the pancreas, tumor, and multiple surrounding anatomical structures (nnUnet_MS). An external, publicly available test set was used to compare the performance of the three networks. The nnUnet_MS achieved the best performance, with an area under the receiver operating characteristic curve of 0.91 for the whole test set and 0.88 for tumors &lt;2cm, showing that state-of-the-art deep learning can detect small PDAC and benefits from anatomy information.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

A surgical technique aimed at rerouting aqueous humor (AH) outflow from the anterior chamber to the suprachoroidal space (SCS) without performing surgical cyclodialysis was developed to decrease intraocular pressure (IOP) in glaucoma patients. The surgical outcomes of the technique were retrospectively analyzed in fifty-eight patients. At 6, 12, and 24 months, the mean IOP decreased from 27.8±8.3 to 14.95.0 mmHg, median 15.0 (25th percentile (p25 )13.0; 75th percentile (p75) 18.0), and 15.23.3 mmHg; hypotensive medication use reduced from median (p25; p75) 3 (2; 3) to 0 (0; 2), 0 (0; 2), and 0 (0; 1.5), and complete success was achieved in 62.8%, 51.2%, and 32.5% cases, with partial success in 28.4%, 44.2%, and 62.5% cases, respectively. Eight cases (13.8%) presented unsatisfactory outcomes. Intra- and postoperative complications were few and manageable. No bleb formation was observed in any of the cases. In 50% of cases, conjunctival lymphatic vessels (CLVs) developed following surgery in superior quadrants. The technique is safe and effective in providing a long-term decrease in IOP and hypotensive medication use. It was hypothesized in this study that the IOP decrease occurred as a result of enhanced AH outflow from the SCS to CLVs through intrascleral microchannels connecting the SCS to CLVs.