Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Minimal rotating thermodynamic systems are addressed. Particle m placed into the rotating symmetrical double-well potential (bowl), providing binary logical system is considered. The condition providing the transfer of the particle from one frictionless half-well to another, and in this way possibility to record 1 bit of information is derived. The procedure of recording turns out to be irreversible; it is impossible to return the particle to its initial state under rotation about the same axis. The same rotating double-well system exerted to the thermal noise is considered. Minimal rotating thermal engine built of the rotating chamber, movable partition and the particle confined within the chamber is treated. Rotation of the system displaces the partition; thus, enabling erasing of one bit information. Erasing of 1 bit of information is due to the inertia (centrifugal force) acting on the partition. Isothermal expansion of the “minimal gas” expectedly gives rise to the Landauer bound. Compression of the “gas” with the rotation around the same axis is impossible and demands the additional axis of rotation. The interrelation between the possibility of recording/erasing information and the symmetry of the system is considered.

Background: The practice of self-medication is common worldwide and is an important component of medical self-care. However, the practice can be dangerous and is linked to various risks for the patients and the entire community. This study aimed to estimate the prevalence and factors associated with self-medication among Bangladeshi adults. Methods: A cross-sectional survey was conducted between April and June 2021 among Bangladeshi adults (aged >19 years) using convenient sampling. A total of 1320 data were collected through face-to-face interviews using a standardized questionnaire. Multivariable logistic regression analysis was used to identify factors associated with self-medication practice (SMP). Results: Overall, 41% of adults in our survey reported SMP. The most common illnesses that prompted SMP were common cold/flu (66.4%), gastric problems (65%), and headache (64.4%). The most frequent reasons for SMP were to get better services (30.59%), perceive SMP without side effects (23.28%), and save time with effectiveness (14.56%). Potential risk factors included 10 years (AOR = 1.91; 95% CI: 1.04 - 3.50) and >12 years of schooling (AOR = 5.03; 95% CI: 2.27 - 11.15), being a businessman (AOR = 4.64; 95% CI: 1.74 - 12.37), having ≤6 family members (AOR = 2.13; 95% CI: 1.40 - 3.24), being a member of a social group (AOR = 1.53; 95% CI: 1.10 - 2.12), a health status check after every six months (AOR = 1.52; 95% CI: 1.08 - 2.13), and current ill-health (AOR = 1.41; 95% CI: 1.06 - 1.87). Protective factors identified included ≤30 years of age (AOR = 0.40; 95% CI: 0.17 - 0.93), and practice of modern (AOR = 0.39; 95% CI: 0.22- 0.69) and herbal (AOR = 0.45; 95% CI: 0.21- 0.97) healing types. Conclusion: More than one-third of the study participants reported practicing self-medication. Increasing the community’s awareness of the extreme consequences of SMP and not just the average experience might sway individuals away from SMP, and implementing strict jurisdiction could be a way to minimize the SMP.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

The article deals with auxetic structures made on the basis of suitably connected rigid rotating squares (from Grima and Evans), with axes of rotation on the squares’ surface. The geometric model and the resulting relationships that allow for the determination of Poisson’s ratio are considered in detail. It is demonstrated that changing the rotation axis position does not affect the negative Poisson’s ratio, equal to -1. The models built confirm the initial considerations and can offer new application possibilities.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

With reference to Planck scale, Mach’s relation, increasing support for large scale cosmic anisotropy and preferred directions and by introducing two new parameters Gamma and Beta, right from the beginning of Planck scale, we make an attempt to estimate ordinary matter density ratio, dark matter density ratio, mass, radius, temperature, age and expansion velocity (from and about the baby universe in all directions). We would like suggest that, from the beginning of Planck scale, 1) Dark matter can be considered as a kind of cosmic foam responsible for formation of galaxies. 2) Cosmic angular velocity is directly proportional to squared cosmic temperature. 3) Ratio of critical temperature to actual temperature plays a heuristic role in understanding ordinary and dark matter density ratios. 4) Cosmic expansion velocity increases with decreasing total matter density ratio. 5) There is no need to consider dark energy for understanding cosmic acceleration.

Passive radar detection emerges as a pivotal method for environmental perception and target de-tection within radar applications. Leveraging its advantages, including minimal electromagnetic pollution and efficient spectrum utilization, passive radar methodologies have garnered increasing interest. In recent years, there has been an increasing selection of passive radar signal sources, and the emerging 5G has the characteristics of high frequency band, high bandwidth, and a large number of base stations, which make it have significant advantages in passive radar. Therefore, this paper introduces a passive radar target detection method based on 5G signals and designs a rotating target speed measurement experiment. In the experiment, this paper validated the method of de-tecting rotating targets using 5G signals and evaluated the measurement accuracy, providing a research foundation for passive radar target detection using 5G signals and detecting rotating targets such as drone rotors.

In this paper, a new type of self-excited thermomechanical oscillator containing an oscillating shape memory alloy (SMA) filament with two symmetrically arranged spheres is investigated. The self-excitation of the oscillations is due to a heater of constant temperature, which causes periodic contractions of the filament when it approaches it. The contracted filament moves away from the heater a distance sufficient to cool it. Under the action of the weight of the spheres, the cooled filament re-approaches the heater, causing the above processes to repeat periodically. On the basis of experimental studies, approximating functions of the heater's heat field distribution are derived. A dynamic model of the oscillator has been created, in which the minor and major hysteresis in the SMA alloy and the distribution of the heat field around the heater have been taken into account. By numerical solutions of the differential equations, the laws of motion of the spheres are obtained. The displacements of the spheres in two perpendicular directions were measured using an experimental system. The obtained experimental results validate the proposed dynamic model and its assumptions with a high degree of confidence. Conclusions are drawn about the stochastic nature of the oscillations due to the hysteresis properties of the SMA and the temperature variation of the natural frequency of the oscillating system.

The concept of economic self-reliance, widely known by Thai people as the philosophy of sufficiency economy, has been widely promoted in rural Thai societies. By practicing this philosophy, it is expected that the citizens’ quality of life and local environments could be sustainably improved. This study aims to explore the contribution of the community practices of the sufficiency economy philosophy to rural villagers’ quality of life improvement, and to investigate potential factors that determine the trust of villagers in the philosophy. With the purpose to propose strategies which could enhance trust and promote villagers’ practices of the philosophy, the study investigated influences of three relevant factors on trust towards the philosophy. Those factors included factors related to cognitive-based trust, factors related to emotional-based trust, and factors related to demographic characteristics. Questionnaire surveys and in-depth interviews with community leaders and local villagers were conducted in the Ban Jamrung community, in Thailand’s Rayong province. The results of the statistical analysis revealed that the residents who applied the sufficiency economy philosophy in their daily lives experienced a relatively better quality of life. Additionally, it was found that trust in the philosophy could be predicted more by rational factors than by emotional factors. These findings could be utilized to develop strategies to maintain and enhance the trust of the people in the philosophy of sufficiency economy.

Recently, some authors have developed a shell-less culture system for chick embryos by using a plastic lm as culture vessels. We will show that velocity of rotation of vessels in incubator and temperature have direct relations with growth of chick embryos. We also obtain a mathematical relation between velocity, temperature and rate of growth of chick embryo.

In this paper, we discuss optical properties of the topologically charged rotating black hole. We study the horizon, the photon region, the shadow of the black hole and other observables. The results show that in addition to the black hole spin parameter $a$, the other two parameters, five-dimensional mass parameter $\beta$ and electric charge $q$, are also found to affect the horzion, the photon region and the black hole shadow. In a certain range, with the increase of the three parameters, the horizon distance, shape of the photon region and the black hole shadow will all shrink. Moreover, with the increase of these three parameters, the distortion parameter $\delta_{s}$ gradually increases, while the peak of the black hole energy emission rate decreases.

For many engineering applications it is sufficient to use the concept of simple materials. However, higher gradients of the kinematic variables are taken into account to model materials with internal length scales as well as to describe localization effects using gradient theories in finite plasticity or fluid mechanics. In many approaches length scale parameter have been introduced that are related to a specific micro structure. An alternative approach is possible, if a thermodynamically consistent framework is used for material modelling as shown in the present contribution. However, even if sophisticated and thermodynamically consistent material models can be established there are still not yet standard experiments to determine higher order material constants. In order to contribute to this ongoing discussion system identification based on the method of self-adaptive filtering is proposed in this paper. To evaluate the effectiveness of this approach it has been applied to second-order gradient materials considering longitudinal vibrations. Based on thermodynamically consistent models that have been solved numerically it has been possible to prove that system identification based on self-adaptive filtering can be used effectively for both narrow-band and broadband signals in the field of second-order gradient materials. It has also been found that the differences identified for simple materials and gradient materials allow for condition monitoring and detection of gradient effects in the material behavior.

The social- and self-directed behaviours of two golden lion tamarins (Leontopithecus rosalia) was investigated while having residence in the tropical house of Aalborg Zoo, Denmark. The behaviour of the female had been distinct from the male since 2018. Despite several diagnostic examinations and medicinal treatments, the cause of the aberrant and apparently stereotypical behavioural patterns remained undetermined, which initiated this study. The pair were recorded throughout a predetermined observation period and these recordings were analysed to illuminate the behaviours of the individuals. The results showed that there were differences in the type, frequency, and durations of both social- and self-directed behaviours between the sick female and the healthy male. The female expressed both social- and self-directed behaviours more frequently and for longer durations, while the male were more socially reserved and did not engage in social behaviours as frequently. Furthermore, subsequent necropsy of the female revealed uro-genital disease.

Owing to the nondiffracting, self-accelerating, and self-healing properties, Airy beams of different nature have become a subject of immense interest in the past decade. Their interesting properties have opened doors to many diverse applications. Consequently, the questions of how to properly design spatial manipulation of Airy beams or how to implement them in different setups have become important and timely in the development of various optical devices. Here, based on our previous work, we present a short review on the spatial control of Airy beams, including the interactions of Airy beams in nonlinear media, beam propagation in harmonic potential, and the dynamics of abruptly autofocusing Airy beams in the presence of a dynamic linear potential. We demonstrate that under the guidance of nonlinearity and external potential, the trajectory, acceleration, structure, and even the basic properties of Airy beams can be adjusted to suit specific needs. We describe other fascinating phenomena observed with Airy beams, such as self-Fourier transformation, periodic inversion of Airy beams, and the appearance of spatial solitons in the presence of nonlinearity. These results have promoted the development of Airy beams, and have been utilized in various applications, including particle manipulation, self-trapping, and electronic matter waves.

Non-normal mode stability analysis has long been employed to study linear transient characteristics of wall bounded shear flows. However, the application of this approach to investigate shear flows with stratified thermal conditions (STCF) has received limited attention. This paper examines thermal effects on Taylor-Couette flow. The results in this study indicate the possibility of a subcritical bifurcation in stratified Taylor-Couette flow.

Unification point of view, quantum cosmology must be given a priority and one should make a note that, Spin is a basic property of quantum physics and rotation is a very common experience. In this context, we have developed a quantum model of cosmology associated with Machian universe having Planck scale origin, total dark matter, light speed rotation and equality of gravitational self energy density and thermal energy density. We would like to appeal that, observed cosmic radius and age seem to be shortened by 146.3 times their actual magnitudes.

We develop new theory from a broad case-study approach to explore a better understanding of what constitutes knowledge and its value as identifiable to human-machine teams. From past research, this trail of exploration will lead to these initial questions: What is the value of debate in the furtherance of knowledge? Will machines with AI be able to contribute to a debate if we humans cannot define it or determine its value sufficiently for a machine’s understanding, contribution, exploration and identification? Like humans, as teammates, machines must be able to determine with AI what constitutes the usable knowledge that contributes to a team’s success in the field (e.g., testing "knowledge" in the field, identifying new knowledge, using knowledge to develop innovation) or its failure (viz., trouble shooting; identifying weaknesses; discovering vulnerabilities, hiding by deception). It matters not whether a debate is public, private or unexpressed by an individual human or machine agent alone; we speculate in this exploration that the process advances the science of autonomous human-machine teams and assists in interpretable machine learning. We conclude with questions and a speculation: How does a human become aware or express its awareness of knowledge? Can a machine be as expressive as its human teammates? And how does a human-machine teammate become aware that its teammates possess sufficient knowledge to perform a task? We speculate that the structure of “knowledge," once found, is resistant to alternatives (i.e., it is ordered); that its functional utility is generalizable; and that its applications are multifaceted (akin to maximum entropy production). The complexity of the team is taken into consideration in our search for knowledge, which can also be used as an information metric.

Cutaneous melanoma (CM) is a candidate for screening programs, since its prognosis is excellent when diagnosed in an early disease stage. Targeted screening of those at high risk for developing CM, a cost-effective alternative to population-wide screening, requires valid procedures to identify the high-risk group. Self-assessment of the number of nevi has been suggested as a component of such procedures, but its validity has not yet been established. We analyzed the level of agreement between self-assessments and expert assessments of the number of melanocytic nevi in the area between the wrist and the shoulder of both arms based on 4548 study subjects in whom mutually blinded double counting of nevi was performed. Nevus counting followed the IARC protocol. Study subjects received written instructions, photographs, a mirror, and a “nevometer” to support self-assessment of nevi larger than 2 mm. Nevus counts were categorized based on the quintiles of the distribution into five levels defining a nevus score. Cohen’s weighted kappa-coefficient was estimated to measure the level of agreement. In the total sample, agreement between self-assessments and expert-assessments was moderate (raw agreement: 50.29%, weighted κ=0.596). Self-assessed nevus counts were higher than those determined by experts (mean differ-ence: 3.33 nevi). The level of agreement was independent of sociodemographic and cutaneous factors; however, participants’ eye color had a significant impact on the level of agreement. Our findings show that even with comprehensive guidance, only a moderate level of agreement between self-assessed and expert-assessed nevus counts can be achieved. Self-assessed nevus information does not appear to be reliable enough to be used in individual risk assessment to target screening activities.

The paper proves the existence of a family of axisymmetric equilibrium figures as solutions of a stationary problem with unknown boundaries for the Navier–Stokes equations corresponding to the slow rotation of a viscous compressible two-layer liquid mass about some axis. It is assumed that the liquids are barotropic, capillary and have different viscosities, the internal fluid being bounded by a closed surface. This interface does not intersect with the external boundary of the cloud. The proof is based on implicit function theorem and carried out in the Hölder spaces.

Considering rotation-induced centrifugal stiffening, spin softening, and Coriolis effects, the three-dimensional finite element model of a rotating blade with a dovetail structure is built through the contact dynamics theory. The fixed-interface component mode synthesis method is then adopted to reduce the model for high computational efficiency and adequate model accuracy. The effects of the number of normal modes on the first-six-order modal characteristics of the model varying with the rotating speed are studied between the reduced and full models. Next, the influence of rotating speed and friction factor on the nonlinear dynamic characteristics of the model under the action of aerodynamic force are elaborately discussed. The results show that: (1) tenon-mortise joint contact-induced nonlinearity under low rotating speeds results in the intermittent interference of contact surfaces and frequency multiplications of aerodynamic excitation frequency in the spectrum cascades, while that under high rotating speeds causes the continuous interface contact and asynchronous excitation at the tenon-mortise joint; (2) the increase of friction factor results in a lower contact pressure distribution and the right shift of the resonance peak (i.e., hard nonlinearity).

Multirotors are gaining great importance in the layout of innovative and more agile mobility. In this framework, a possible solution to developing an aircraft complying with the stringent size requirements characterizing this type of application can be a coaxial rotor configuration. To exploit the several possibilities linked to coaxial rotors, a scaled experimental model is designed to evaluate the performances of the counter-rotating propellers system, concerning the distance between the two propellers. Both thrust and noise are considered as parameters of interest. Two brushless motors are deployed whereas the propellers' angular velocity, in terms of round per minute (rpm), is controlled by an external control system. Tests are conducted on both single isolated propellers as well as on the counter-rotating system: the two propellers and their respective motors have been characterized concerning the thrust. Furthermore, a comparison with a numerical model is performed. Noise evaluation on the single propeller has shown a motor contribution prevalence at a low rpm regime (1140-1500 rpm) and a propeller prevalence for angular velocities higher than 1860 rpm. By varying the distances between the propellers a sensitivity analysis is performed with the aim of identifying the optimum configuration taking into account both noise and thrust performances.

The most cited evidence for (nonbaryonic) dark matter has been an apparent lack of visible mass to gravitationally support the observed orbital velocity of matters in rotating disk galaxies. Yet measurement of the mass of celestial objects cannot be straightforward, requiring theories derived from the known physical laws along with some empirically established semi-quantitative relationship. The most reliable means for determining the mass distribution in rotating disk galaxies is to solve a force balance equation according to Newton’s laws from measured rotation curves, similar to calculating the Sun’s mass from the Earth’s orbital velocity. Another common method to estimate galactic mass distribution is to convert measured brightness from surface photometry based on empirically established mass-to-light ratio. For convenience, most astronomers commonly assumed a constant mass-to-light ratio for estimation of the so-called “luminous” or “visible” mass, which should not be expected accurate. The mass determined from rotation curve typically exhibit an exponential-like decline with galactrocentric distance, qualitatively consistent with observed surface brightness. This fact scientifically suggests variable mass-to-light ratio of baryonic matter in galaxies without the need for dark matter.

Primary importance is devoted to Fault Detection and Diagnosis (FDI) of electrical machine and drive systems in modern industrial automation. The widespread use of Machine Learning techniques has made it possible to replace traditional motor fault detection techniques with more efficient solutions that are capable of early fault recognition by using large amounts of sensory data. However, the detection of concurrent failures is still a challenge in the presence of disturbing noises or when the multiple faults cause overlapping features. The contribution of this work is to propose a novel methodology using multi-label classification method for simultaneously diagnosing multiple faults and evaluating the fault severity under noisy conditions. Performance of various multi-label classification models are compared. Current and vibration signals are acquired under normal and fault conditions. The applicability of the proposed method is experimentally validated under diverse fault conditions such as unbalance and misalignment.

This study addresses the critical challenge of Speech Enhancement (SE) in noisy environments, where the deployment of Deep Neural Networksolutions on microcontrollers is hindered by their extensive computational demands. Focusing on this gap, our research introduces a novel SE method optimized for MCUs, employing a 2-layer GRU model that capitalizes on perceptual speech properties and innovative training methodologies. By incorporating self-reference signals and a dual strategy of compression and recovery based on the Mel scale, we develop an efficient model tailored for low-latency applications. Our GRU-2L-128 model demonstrates a significant reduction in size and computational requirements, achieving a 14.2× decrease in model size and a 409.1× reduction in operations compared to traditional DNN methods like DCCRN, without compromising performance. This advancement offers a promising solution for enhancing speech intelligibility in resource-constrained devices, marking a pivotal step in SE research and application.

Two polyurethanes (PUs) were similarly synthesized by reacting a cycloaliphatic isocyanate with 1,4 butanediol and two polyols of different nature (polyester, polycarbonate diol) with molecular weights of 1000 Da. The PU made with polycarbonate diol polyol (YCD) was the only showing intrinsic self-healing at 20 °C. For assessing the mechanism of intrinsic self-healing of YCD, a structural characterization by molecular weights determination, infrared and X-ray photoelectronic spectroscopies, differential scanning calorimetry, X-ray diffraction, thermal gravimetric analysis and dynamic mechanical thermal analysis was carried out. It was concluded that the self-healing at 20 °C of YCD was due to non-covalent dynamic exchange interactions among the carbonate groups of the soft segments. Therefore, the chemical nature of the polyol played a key role in developing PUs with intrinsic self-healing at 20 °C.

Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.

Solid-state LiDAR offers multiple advantages over mechanism mechanical LiDAR, including higher durability, improved coverage ratio, and lower prices. However, solid-state LiDARs typically possess a narrow field of view, making them less suitable for odometry and mapping systems, especially for mobile autonomous systems. To address this issue, we propose a novel rotating solid-state LiDAR system that incorporates a servo motor to continuously rotate the solid-state LiDAR, expanding the horizontal field of view to 360∘. Additionally, we propose a multi-sensor fusion odometry and mapping algorithm for our developed sensory system that integrates an IMU, wheel encoder, motor encoder and the LiDAR into an iterated Kalman filter to obtain a robust odometry estimation. Through comprehensive experiments, we demonstrate the effectiveness of our proposed approach in both outdoor open environments and narrow indoor environments.

With reference to Planck scale, increasing support for large scale cosmic anisotropy and preferred directions and by considering an increasing ratio of Hubble parameter to angular velocity, right from the beginning of Planck scale, we make an attempt to estimate ordinary matter density ratio, dark matter density ratio, mass, radius, temperature, age and expansion velocity (from and about the baby universe in all directions). We would like suggest that, from the beginning of Planck scale, 1) Dark matter can be considered as a kind of cosmic foam responsible for formation of galaxies. 2) Cosmic angular velocity decreases with square of the decreasing cosmic temperature. 3) Increasing ratio of Hubble parameter to angular velocity plays a crucial role in estimating increasing cosmic expansion velocity and decreasing density ratios of dark matter and ordinary matter. 4) There is no need to consider dark energy for understanding cosmic acceleration.

In this paper we propose a novel self-supervised approach of keywords and keyphrases retrieval and extraction by an end-to-end deep learning approach, which is trained by contextually self-labelled corpus. Our proposed approach is novel to use contextual and semantic features to extract the keywords and has outperformed the state of the art. Through the experiment the proposed approach has been proved to be better in both semantic meaning and quality than the existing popular algorithms of keyword extraction. In addition, we propose to use contextual features from bidirectional transformers to automatically label short-sentence corpus with keywords and keyphrases to build the ground truth. This process avoids the human time to label the keywords and do not need any prior knowledge. To the best of our knowledge, our published dataset in this paper is a fine domain-independent corpus of short sentences with labelled keywords and keyphrases in the NLP community.

Condition monitoring of rotating shafts is essential for ensuring the reliability and optimal performance of machinery in diverse industries. In this context, as industrial systems become increasingly complex, the need for efficient data processing techniques is paramount. Deep learning has emerged as a dominant approach due to its capacity to capture intricate data patterns and relationships. However, a prevalent challenge lies in the black-box nature of many deep learning algorithms, which often operate without adhering to the underlying physical characteristics intrinsic to the studied phenomena. To address this limitation and enhance the fusion of data-driven methodologies with the fundamental physics of the system under study, this paper leverages physics-informed neural networks (PINNs). Specifically, a simple but realistic numerical case study of an extended Jeffcott rotor model, encompassing damping effects and anisotropic supports for a more comprehensive modelling, is considered. PINNs are used for the estimation of five parameters that characterize the health state of the system. These parameters encompass the radial and angular position of the static unbalance due to the disk installed on the shaft, the stiffness along the principal axes of elasticity, and the non-rotating damping coefficient. The estimation is conducted solely by exploiting the displacement signals from the centre of the disk and, to showcase the efficacy and precision provided by this novel methodology, various scenarios involving different constant rotational speeds are examined. Additionally, the impact of noisy input data is also taken into account within the analysis.

All kinds of vessels consist of dozens of complex machineries with rotating parts and electric motors that operate continuously in a harsh environment with excess temperature and humidity, vibration, fatigue and load. A breakdown or malfunction in one of these machineries can significantly impact the vessel’s operation and safety and consequently, the safety of the crew and the environment. To maintain operational efficiency and seaworthiness, the shipping industry invests substantial resources in preventive maintenance and repairs. This research presents the economic and technical benefits of predictive maintenance over to traditional preventive maintenance, and repair by replacement approaches in the maritime domain. By leveraging modern technology and Artificial Intelligence, we can analyze real-time operating conditions of machinery, enabling early detection of potential damages and allowing for effective planning of future maintenance and repair activities. In this paper, we propose and develop a Convolutional Neural Network that is fed with raw vibration measurements acquired in a laboratory environment from the ball bearings of a motor. Then, we investigate whether the proposed network can accurately detect the functional state of ball bearings and categorize any possible failures present, contributing to improved maintenance practices in the shipping industry.

In the recent years, intelligent data-driven faultdiagnosis methods on gearboxes have been successfully developedand popularly applied in the industries. Currently, most ofthe machine learning techniques require that the training andtesting data are from the same distribution. However, thisassumption is difficult to be met in the real industries, sincethe gearbox operating conditions usually change in practice,which results in significant data distribution gap and diagnosticperformance deteriorations in applying the learned knowledgeon the new conditions. This paper proposes a deep learning-based domain adaptation method to address this issue. Theraw current signals are directly used as the model inputs fordiagnostics, which are easy to collect in the real industries andfacilitate practical applications. The maximum mean discrepancymetric is introduced to the deep neural network, the optimizationof which guarantees the extraction of generalized machineryhealth condition features across different operating conditions.The experiments on a real-world gearbox condition monitoringdataset validate the effectiveness of the proposed method, whichoffers a promising tool for cross-domain diagnosis in the realindustries.

Background: Visual acuity (VA) assessments are crucial in ophthalmology but traditionally rely on in-clinic evaluations. The emergence of telemedicine has spurred interest in creating dependable self-administered VA tests for use beyond standard clinical environments. This study evaluates the practicality and validity of a self-administered Near VA card test against traditional Snellen and Rosenbaum Pocket Vision Screener (RPVS) methods for home monitoring and enhancing clinical workflow. Methods: In a cross-sectional study a near VA card (Hadassah Self-Visual Acuity Screener-HSVA) was developed with written and videotaped instructions for self-use. Patients with a minimal best corrected VA (BCVA) of 1.0 LogMAR in at least one eye were recruited from Ophthalmology and Optometry clinics. Outcomes included mean BCVA difference between the self-administered and those obtained by the examiner, and correlations among BCVA values obtained by Snellen, RPVS, HSVA and previous distance BCVA according to the patient electronic medical records. Results: A total of 275 participants (mean age: 42.5±19.4 years, range: 18-89 years, 47% female) were included. Test-retest reliability analysis for the HSVA demonstrated very good correlation and repeatability (n=38 patients.; Rs=1.0, P

Roundabouts need capacity and safety improvements compatible with manual-driven, not only with autonomous vehicles. The signaling and control of roundabouts must evolve and incorporate current technologies. For that, we approach roundabouts as synchronous switches of vehicles. This paper describes Synchronous Roundabouts with Rotating Priorities, a roundabout control system based on vehicle platoons arriving at the roundabout at speed identical to the roundabout and within the time slot assigned to their entry, avoiding conflicts and stops, thus increasing roundabout capacity and safety. Signaling is visual for human drivers and also wireless for connected and autonomous vehicles. We evaluate analytically and with simulations roundabouts of different radius for several values of the average distance between vehicles. Average delays are 28,7 % lower, with negligible dispersion. The capacity improvements depend on design parameters: in our set is moderate for small roundabouts but goes up to 70-100 % for short distances and medium and large roundabouts.

Rapid SARS-CoV-2 self-tests have the potential to expand access to COVID-19 testing and improve community-level case detection, particularly in resource-constrained countries such as Kenya. However, prior to their introduction, their acceptability must be assessed. This qualitative study explored key decision-takers’ values towards SARS-CoV-2 self-testing in Kenya. Healthcare workers, representatives of civil society, and potential implementors from Mombasa and Taita-Taveta were selected as decision-takers. Semi-structured interviews and focus group discussions were used to collect data on their values towards self-testing. A thematic analysis approach was applied. Most informants considered that the Kenyan public is equipped to accept and use self-testing safely as an approach to help to reduce workload at public healthcare facilities, and know one’s COVID-19 status in a private manner. The informants emphasized the need to provide counselling to end-users, to support those needing to self-isolate, and to engage different civil society stakeholders in information provision on self-testing. Fear of stigma and of forced isolation were noted as potential deterrents to self-testing uptake for some individuals. In conclusion, there is high acceptability of self-testing in Kenya among decision-takers. However, enhanced education, counselling, and addressing deterrents to testing would be helpful to ensure effective use of SARS-CoV-2 self-testing in Kenya.

Many have speculated that events of personal and financial loss in Rembrandt’s life caused depression and that this is revealed by examination of his self-portraits particularly those painted in old age. Some report detecting various physiological diseases associated with aging, including vision impairment, which may have affected his mood and work. Aging and neurodegenerative disease which often accompanies it, are both associated with depression. Recent advances in imaging and computer technology make it possible to empirically examine changes in artistic style which can contribute to understanding artists’ physical and mental health. In the current study changes in contrast, colour and fractal dimension were measured in the entire corpus of Rembrandt’s painted self-portraits and portraits to determine whether changes in style indicate depression or disease. Productivity was also examined as an indirect indicator. Given the high salience attributed to self-images, it also examined whether differences in style could be detected between self-portraits and portraits of related and unrelated others. The results indicate that it is unlikely that Rembrandt suffered from unipolar or bipolar depression, age-related cognitive decline, or neurodegenerative disease. The data are consistent with someone experiencing episodes of low mood consistent with normal grieving and adversity followed by resilient recovery. There is evidence of a gradient in saliency and complexity between self-portraits and related and unrelated portraits, of a less formal style in portraits of related others and of a ‘late’ style identified by leading art historians consistent with macular degeneration. The results are also consistent with an association of aesthetic preference with mid-level fractal values tending towards the Golden Mean long associated with beauty in nature and in art.

The article describes the basic parts and the overall design of the laboratory machine, which can be used to measure vibrations generated by a rotating conveyor roller attached to the flattened parts of its axis in the cut-outs of the conveyor idler support. On the structurally modified support of the conveyor idler consisting of the insertion of a plastic element placed between the roller axis and the support cut-out, the vibration acceleration values of the rotating roller were measured and compared with the values of the traditional roller axis placement in the steel support. The size of the peripheral speed of the roller was determined, during the experimental measurements, by controlling the speed of the electric motor using a frequency converter. The obtained results of the measured values of vibration velocities in three mutually perpendicular planes showed a reduction in vibration values of about 15% when using plastic holders. The paper aims to present one of the possible technical solutions that can limit the vibration values transmitted to the supporting structure of the conveyor belt, generated by the rotating casing of the conveyor roller.

Given the existing movable rotating plate type grading device for potatoes with a high safety factor and heavy mass, the body frame of the grading device and movable rotating plate were optimized and a lightweight design was carried out. Based on ANSYS Workbench 2022, the static analysis of the body frame before and after improvement was compared, and it was verified that the strength and deformation of the optimized body frame met the design requirements, and the weight of the optimized body frame was reduced by 32.3%. Based on the direct optimization module of ANSYS Workbench 2022, the plate length, width, and height were used as design variables for the lightweight design of the movable rotating plate. The MOGA algorithm was used to generate sixty design solutions, and the optimal combination of size parameters for the plate was 610 mm, 95mm, and1.2 mm. Compared with the whole grading device before optimization, the total mass was reduced by 22.86% after optimization. The research of this article provides a reference for the structural design and optimization analysis of potato grading devices.

A novel method based on a hybrid incremental modeling approach has been designed and applied to imbalance detection in ultra-high precision rotating machines. The model is obtained by a two-step iterative process that combines an overall model (least-squares fitting) with a local model (fuzzy k-nearest-neighbour) to take advantage of their complementary capacities. Three normalization strategies of evaluating the effect on accuracy are analyzed. A comparative study demonstrates that the hybrid incremental model provides better error-based performance indices for detecting imbalance than a nonlinear regression model and an adaptive neural-fuzzy inference system model. The suitability of Mahanolobis normalization for hybrid incremental modeling is also demonstrated in this case study. The proposed strategy for imbalance detection is simple, fast, and non-intrusive, reducing the deterioration in the performance of ultra-high precision rotating machines due to vibrations.

Today, issues related to people’s mental health and well-being have been described as a challenge for society, globally as well as in Sweden. This calls for new approaches to mental health promotion. The aim was to evaluate the adequacy of the content and structure, describing experiences of study circles as a means of supporting participants' self-care and self-compassion. The overall design is a descriptive, QUAL+quan design, where quantitative and qualitative results are integrated. Five participants participated in a focus group interview, of whom four completed questionnaires. One individual interview was conducted with the study circle leader. Study circles can be an arena for mental health promotion as learning and sharing of experience contributes to a sense of coherence, as well as self-compassion and a genuine concern for one’s own and others' wellbeing, but not considered an alternative to psychiatric care, for those in need of professional services. Study circles can be a possible means to support self-care and thereby promote mental health in the general population, and a valuable contribution to public health. However, in addition to modifications of the content, further research is needed on the qualifications for study circle leaders as well as the dissemination of study circles.

A theoretical nonlocal thermoelastic model for studying the effects of the thermal conductivity variability on a rotating nanobeam has been described in the present article. The theory of thermal stress is employed using the Euler–Bernoulli beam model and generalized heat conduction with phase lags. It is believed that the thermal conductivity of the current model varies linearly according to temperature. Due to variable harmonic heat, the considered nanobeam excited and was subjected to a time-varying exponential decay load. Using the Laplace transform process, the analytical solutions for displacement, deflection, thermodynamic temperature and bending moment of rotating nanobeams are provided in final forms and a numerical example has been taken to address the problem. A comparison of the stated results was displayed and additionally, the influences of non-local parameters and varying load were analyzed and examined. We also investigate how the linear changes in the temperature of physical properties can influence both the static and dynamic responses to the rotating nanobeam.

The present paper reports an exact approach quantifying the electromagnetic contribution to the anomalous magnetic moment occurring in isolated system comprised of non-composite particle carrying elementary electric charge. Essential averaging procedure and regularization of the electromagnetic field potentials necessary when quantifying the electromagnetic self-interactions and when deriving equations of motion without singularities and obeying the conservation laws are thoroughly discussed. The study shows that the dynamics of the considered system is associated to unique classical transcendental equations of motion satisfied by the particle's velocity and the electromagnetic contribution to the anomalous $g$-factor known from the quantum electrodynamics. The equations of motion lead to an exact analytical expression for the anomalous $g$-factor that provides more accurate result than that calculated with the aid of quantum electrodynamics. It matches the experimentally measured value reported in the literature to a one part per trillion. We obtain a_e=0.00115965218000(65) thus reveling the potential of non-perturbative, non-probability methods in predicting the electron's anomalous g-factor.

The research proposes a self-directed paradigm with self-design using the existing technology with LMS modules, discussions, and self-tests. The research establishes its criteria for assurance of teaching and learning known as 7x2C for the compliance of content, and appearance along with other criteria for the analysis. The above technology of web and LMS is tested for a business course that is technology-oriented in creating an experiential learning system for Covid-19 awareness. Similarly, among other ideas, an environment for educating learners about diabetes and obesity has been designed. The project is known as Sunchoke with its theme of Grow, Eat, and Heal. The educators can use their technology and apply self-directed pedagogy to transform this approach to their customized ways by using their content and rubrics.

Purpose: To identify the impact of dealing with COVID-19 patients in clinical areas on nurses' professional self-concept and self-confidence. Background: Professional self-concept is considered a critical factor in the recruitment/retention process in nursing, nursing shortage, career satisfaction, and academic achievements. Professional self-confidence is also a crucial determinant in staff satisfaction, reducing turnover, and increasing work engagement. Design: Descriptive, comparative study. Methods: The study was conducted between February to May 2021 by utilizing a convenience sampling technique. A total of 170 nurses from two facilities were recruited from two COVID-19 and non-COVID-19 designated facilities. The level of professional self-concept and self-confidence was assessed by utilizing the Nurses' Self-Concept Instrument and Self-Confidence Scale. Results: The professional self-concept level among the exposed group to COVID-19 patients was lower than the comparison group, while the professional self-confidence level among the exposed group to COVID-19 patients was similar to the comparison group. On the other hand, the satisfied staff and those who received professional training in dealing with COVID-19 patients reported a higher level of professional self-concept. Conclusions: Dealing with COVID-19 patients has an impact on professional self-concept; the exposure group was lower than those who did not deal with COVID-19 patients, while the professional self-confidence level among the exposed group was similar to the comparison group. Getting professional training in dealing with COVID-19 patients and being satisfied at work were significant factors in improving the professional self-concept. Policymakers should create strategies that target the improvement of professional training in dealing with COVID-19 patients.

Citizen science substantially contributes to large-scale biodiversity monitoring and the enhancement of public literacy. While both of the contributions largely depend on the public’s self- regulated learning. In this study, we employed a mix- method approach, incorporating both a questionnaire survey of 133 participants and interviews with 12 volunteers, aiming to explore the feature of self- regulated learning in citizen science, as well as identify the main factors impacting it. The volunteers are all different ages, from different jobs, with varying educational backgrounds. The findings revealed that the educational background of volunteers did not significantly impact their self-regulated learning. However, an increased frequency of participation was linked to higher levels of self-regulated learning. Furthermore, achievement goal orientation mediates the prediction of self-regulation by scientific epistemology. These insights underscore the importance of enhancing citizen science's impact on scientific literacy by fostering self-regulated learning among participants. This can be achieved through explicit instruction in scientific epistemology and by fostering a sense of achievement to boost achievement goal orientations. Additionally, our study advocates for the promotion of social interaction between students and out- of- school citizen scientists in school-based citizen science projects. The main innovation of this study is to consider volunteers as learners, not merely as contributors of data.

Lipophilic oligonucleotide derivatives are a potent approach to the intracellular delivery of nucleic acids. The binding of these derivatives to serum albumin is a major determinant of their fate in the body, as its structure contains several sites of high affinity for hydrophobic compounds. This study focuses on the features of self-association and non-covalent interactions with human serum albumin of novel self-penetrating oligonucleotide derivatives. The study revealed that the introduction of a triazinyl phosphoramidate modification bearing two dodecyl groups at the 3' end region of the oligonucleotide sequence has a negligible effect on its affinity for the complementary sequence. Dynamic light scattering verified that the amphiphilic oligonucleotides under study can self-assemble into micelle-like particles ranging from 8 to 15 nm in size. The oligonucleotides with dodecyl groups form stable complexes with human serum albumin with a dissociation constant of approximately 10-6 M. The oligonucleotide micelles are simultaneously destroyed upon binding to albumin. Using an electrophoretic mobility shift assay and affinity modification, we examined the ability of DNA duplexes containing triazinyl phosphoramidate oligonucleotides to interact with Ku antigen and PARP1, as well as the mutual influence of PARP1 and albumin or Ku antigen and albumin upon interaction with DNA duplexes. These findings, together with the capability of dodecyl-containing derivatives to effectively penetrate different cells, such as HEK293 and T98G, indicate that the oligonucleotides under study can be considered as a platform for the development of therapeutic preparations with a target effect.

The paper presents the basic structural parts, a 3D model and the overall design of a laboratory machine, which was created to detect vibrations generated by the casing of a conveyor roller ro-tating at different speeds. The intention of the authors was to verify whether plastic brackets in-serted into the structurally modified trestles of a fixed conveyor idler can reduce the vibration values transmitted from the rotating conveyor roller to the trestle of a fixed idler. Experimental vibration measurements taken on the non-rotating parts of conveyor rollers, performed on a laboratory machine according to ISO 10816, are suitable for characterizing their operating condi-tions with regard to trouble-free operation. The aim of this paper is to detect the vibrations of a rotating conveyor roller on a laboratory machine in the defined places of a fixed conveyor idler and also on the steel frame of a laboratory machine that represents the supporting track of a belt conveyor. Vibrations detected by piezoelectric acceleration sensors were recorded by a measur-ing apparatus and displayed in the environment of Dewesoft X software. The measurements show that the vibration values grow with the increasing speed of the conveyor roller rotation. Experimental measurements have proven the correctness of the assumption that the vibrations transmitted to the trestle of a fixed conveyor idler are lower by up to 40% when using plastic brackets into which the axle of the conveyor roller is attached, compared to the solution where the axle of the conveyor roller is inserted into the notches of a steel trestle.

An exact solution is obtained for the kinetic energy in the general case of the spatial motion of solids with arbitrary rotation, which differs from the Koenig formula by three additional terms with centrifugal moments of inertia. The description of motion in the Lagrange form and the superposition principle are used, which provides a geometric summation of the velocities and accelerations of the joint motions in the Lagrange form for any particle at any time. The integrand function in the equation for kinetic energy is represented by the sum of the identical velocity components of the joint plane-parallel motions. The moments of inertia in the Koenig formula do not change during movement and can be calculated from the current or initial state of the body. The centrifugal moments change and turn to 0 when rotating relative to the main central axes only for bodies with equal main moments of inertia, for example, for a ball. In other cases, the difference in the main moments of inertia leads to cyclic changes in the kinetic energy with the possible manifestation of precession and nutation, the amplitude of which depends on the angular velocities of rotation of the body. An example of using equations for a robot with one helical and two rotational kinematic pairs is given.

Monitoring complex electro-mechanical processes is not straightforward despite the arsenal of techniques nowadays availanle. This paper presents a method based on Adaptive-Network-based Fuzzy Inference System (ANFIS) to estimate eccentricity of its spinning axis. The method is experimentally tested on an ultra-precision rotating device commonly used for micro-scale turning. The developed model has three inputs, two obtained from a frequency domain analysis of a vibration signal and the third, which is the device rotation frequency. A comparative study demonstrates that an adaptive neural-fuzzy inference system model provides better error-based performance indices for detecting imbalance than a non-linear regression model. This simple, fast, and non-intrusive imbalance detection strategy is proposed to counteract eventual deterioration in the performance of ultra-high precision rotating machines due to vibrations.

In this work, we focus on investigating electrothermal flow in a rotating electric field (ROT-ETF), with primary attention paid to the horizontal traveling-wave electrothermal (TWET) vortex induced at the center of the electric field. The frequency-dependent flow profiles in the microdevice are analyzed using different heat transfer models. Accordingly, we address in particular the importance of electrode cooling in ROT-ETF as metal electrodes of high thermal conductivity while substrate material of low heat dissipation capability are employed to develop such microfluidic chips. Under this circumstance, cooling of electrode array due to external natural convection on millimeter-scale electrode pads for external wire connection occurs and makes the internal temperature maxima shift from the electrode plane to a bit of distance right above the cross-shaped interelectrode gaps, giving rise to reversal of flow rotation from a typical repulsion-type to attraction-type induction vortex, which is in good accordance with our experimental observations of co-field TWET streaming at frequencies on the order of reciprocal charge relaxation time of the bulk fluid. These results point out a way to make a correct interpretation of out-of-phase electrothermal streaming behavior, which holds great potential for handing high-conductivity analytes in modern microfluidic systems.

Tribological testing of moving shaft/sealing pairs in complex environments is at the frontline of research. Machines working in abrasive conditions are subject to different wear effects. It is valid not only on the Earth but especially valid for rovers and future robots used in Mars and Moon missions. The aim of our joint research with the European Space Agency is to study the abrasion phenomena of moving machine elements on Mars and the Moon, by using artificial soil samples (“simulants”). This review detail the available simulant sources and recommend a selection of the most suitable ones for tribological testing. Moreover, the potential mating structural materials subjected to abrasive space applications are reviewed. The tribological tests are exploring the features of the rotary shaft/seal relationship that is subject to dry friction and intense abrasion. By using the simulants, measurements are performed under laboratory conditions with both a sample test and a real shaft/seal connection. Parameters of the selection criteria have been defined and classification of the simulant sources were made. It was found that simulant particle size distribution and chemical substance content is detailed enough only for a limited type of available artificial Moon and Mars soil samples. 4 simulants have been identified and applied later in the tribological testing. For the shaft materials, based on a detailed case study of polymers, steel and aluminium alloys, a high-strength aluminium alloy with a hard anodized surface and a stainless steel were selected for further abrasion tests.

This study aimed to investigate the efficacy of manual therapy and exercise versus synchronized telerehabilitation with self-manual therapy and exercise in treating Subacromial Pain Syndrome (SAPS). Sixty individuals diagnosed with SPS, aged 18-50 years, were randomly assigned to home exercise (HE), manual therapy (MT), and telerehabilitation (TR) groups. Treatment protocols were administered over 8 weeks and included specific exercises and therapy interventions. Out-come measures included Visual Pain Scale (VAS), shoulder range of motion (ROM) via gonio-metric measurements, Quick Disability Arm-Shoulder-Hand Problems Survey (Q-DASH), and patient satisfaction. Results revealed that both MT and TR groups exhibited reduced pain, in-creased ROM, lower Q-DASH scores, and higher patient satisfaction compared to the HE group. However, no significant differences were found between MT and TR groups in pain levels, ROM, Q-DASH scores, or patient satisfaction. The study concludes that both telerehabilitation and manual therapy effectively alleviate pain and are well-received by patients with SPS. Addition-ally, manual therapy demonstrates superiority in enhancing functional levels compared to exer-cise-based interventions. (Registration: NCT05200130)

This paper deals with the design, simulation and implementation of shunt hybrid compensator to maintain the power quality in 3-phase distribution networks feeding different types balanced and unbalanced nonlinear loads. The configuration of the compensator consists of a selective harmonic elimination passive filter, a series connected conventional 6-pulse IGBT inverter, acting as the active filter terminated with a dc link capacitor. The theory and modelling of the compensator based on current harmonic components at the load end and their decomposition in d-q axis frame of reference are utilized in the reference current generation algorithm. Accordingly, the source current waveform is made to follow the reference current waveform using a high frequency carrier based controller. Further, this inner current control loop is supported by a slower outer voltage control loop for sustaining desirable dc link voltage. Performance of the compensator is evaluated through MATLAB simulation covering different types of loads and reduction of harmonic currents and THD at the supply side along with excellent regulation of dc link voltage are confirmed. The performance of a hybrid compensator designed and fabricated using the above principles is evaluated and corroborated with the simulation results.

: BACKGROUND: The prevalence of smoking among students is a growing concern, particular-ly among medical students. Being associated with stress, competitiveness, and various social in-fluences, smoking can have detrimental effects on self-esteem and self-efficacy and may create a vicious cycle that may contribute to students’ well-being and academic performance out-comes.METHODS: A cross-sectional study on 456 medical students was conducted via an online survey using structured questionnaires on socio-demographic characteristics, smoking habits, nicotine dependence, self-esteem, and self-efficacy. RESULTS: The prevalence of smoking was 31.1% The scores of self-esteem and self-efficacy were positively correlated with smoking habits (W1=0.957, W2=0.975, P<0.05). Students presented rather low smoking addiction with male stu-dents having slightly higher scores than female students on self-esteem and self-efficacy, mili-tary students had higher self-esteem scores than civilians with physical activity having a posi-tive correlation with non-smoking behavior. CONCLUSION: According to our results, self-esteem and self-efficacy were slightly positively correlated with smoking habits. Furthermore, there was no statistically significant association between other social factors and smoking. Our results may develop a theoretical basis for medical students’ psychological variables studying for further implementation of university educational programs and preventive interventions em-powering students towards an overall better quality of life, addressing, among others, smoking behaviors.

An electrochemical bioassay based on the rotating droplet electrochemistry by using electron transfer mediator was developed for the evaluation of a wide variety of pollutants such as antibiotics, heavy metals and pesticides in the water environment. Ferricyanide was used as electron transfer mediator for obtaining the catalytic response of Escherichia coli. The electrochemical response of E.coli was measured via hydrodynamic chronoamperometry in a microdroplet on a screen-printed carbon electrode (SPCE). The constructed electrode system successfully evaluate the catalytic response of E.coli solution in presence of ferricyanide. The assay for antibiotic toxicity on E.coli was carried out. The EC50 for ampicillin, sulfamonomethoxine, chlorotetracycline, tetracycline and oxytetracycline valuated by the pre-incubation method were 0.26, 0.77, 5.25, 18.5, 19.0 µM, respectively. The toxicity order was ampicillin &gt; sulfamonomethoxine &gt; chlorotetracycline &gt; tetracycline&gt;oxytetracycline. The proposed method can be used to evaluate the antibiotic toxicities in different real sample, such as pond water, powder and raw milk. Recoveries were found in the range 90 and 99%. The developed methods do not require additional incubation time to evaluate toxicity.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Today's unstable labor market increasingly requires flexibility and adaptability to cope with the threat of unemployment. It can cause distress in people and have a more significant negative impact on fragile workers, such as migrants. This study aimed to test whether a Career Counseling intervention designed for Migrants (CCfM) can develop Career Adaptability and, therefore, both Work Self-efficacy (WSe) and Job Search Self-efficacy (JSSe) perceptions. It was conducted in Italy and involved a sample of 233 migrants, who were asked to respond to a questionnaire available in three languages (Italian, French, and English). Data analysis showed that an improvement was demonstrated in all the variables considered, namely career adaptability (including concern, control, confidence, and curiosity), WSe, and JSSe, even though the CCfM was not directly designed to increase the last one. In addition, the development of career adaptability explained the increase in migrants' WSe and JSSe, and the initial level of career adaptability was found to explain the increase in WSe due to the initial positive level of curiosity.

Cyber Physical Systems (CPS) has been a popular research area in the last decade. The dependability of CPS is still a critical issue, and rare survey has been published in this domain. CPS is a dynamic complex system, which involves various multidisciplinary technologies. To avoid human error and to simplify management, self-management CPS (SCPS) is a wise choice. And to achieve dependable self-management, systematic solution is necessary to verify the design and to guarantee the safety of self-adaptation decision, as well as to maintain the health of SCPS. This survey first recalls the concepts of dependability, and proposes a generic environment-in-loop processing flow of self-management CPS, and then analyzes the error sources and challenges of self-management through the formal feedback flow. Focus on reducing the complexity, we first survey the self-adaptive architecture approaches and applied dependability means; then we introduce a hybrid multi-role self-adaptive architecture, and discuss the supporting technologies for dependable self-management at the architecture level. Focus on dependable environment-centered adaption, we investigate the verification and validation (V&V) methods for making safe self-adaptation decision and the solutions for processing decision dependably. For system-centered adaption, the comprehensive self-healing methods are summarized. Finally, we analyze the missing pieces of the technology puzzle and the future directions. In this survey, the technical trends for dependable CPS design and maintenance are discussed, an all-in-one solution is proposed to integrate these technologies and build a dependable organic SCPS. To the best of our knowledge, this is the first comprehensive survey on dependable SCPS building and evaluation.

Background: The adoption of self-care behaviors among patients with congestive heart failure (CHF) is essential for the management of their health condition. However, there is a lack of tools for estimating self-care in CHF patients. We aim to develop and validate the Hippocratic heart failure self-care scale (HHFSCS). Methods: the scale includes 22 items which are reviewed by a committee of experts. Individuals indicate the frequency at which they follow each self-behavior on a five-point Likert scale. Adult patients with CHF (n=250) from a General Hospital, in Athens, were participated in the study from June 2020 to March 2021. Reliability coefficients and Explanatory Factor Analysis (EFA), using a Varimax rotation and the Principal Components Method were used to assess the psychometric measurements. Results: The Cronbach’s alpha coefficient of the HHFSCS was 0.807. The exploratory factor analysis identified two domains that accounted for 88.44% of the variance of the scale items; however, each sub-scale could not be used as an independent scale. Finally, the test-retest showed a significant strong correlation (r=0.973, p&lt;0.001). Conclusions: The HHFSCS is a reliable and valid tool for assessing self-behaviors in CHF patients. Health professionals can use it in their clinical practice to improve the management of patient’s health conditions.

Detecting, especially locating local degradations at an incipient stage, is very important for mission-critical high voltage rotating machines. One particular challenge of the existing testing techniques is that the characteristic of a local incipient defect is not prominent due to various factors such as averaging with the healthy remainder, attenuation in signal propagation, interference, and varied operating conditions. This paper proposes and investigates the frequency domain reflectometry (FDR) technique based on scattering parameter measurement. The FDR result presents the object length, wave impedance, and reflections due to impedance discontinuity along the measured windings. Experiments were performed on two commercial coils with artificially made defects. These defects include turn-to-turn short, surface creepage, loose coils, and local overheating, which are commonly seen in practice. Two practical water pumps in the field were also selected for investigation. The study outcome shows that the FDR can identify and locate both structure and insulation degradations of both shielded and unshielded objects with good sensitivity. This makes the FDR a comprehensive tool for fault diagnosis and aging assessment.

A four stage semi-pilot scale RFR reactor with ceramic disks as support for TiO₂ modified with silver particles was developed for the removal of organic pollutants. The design presented in this article is an adaptation of the rotating biological reactors (RBR) and its coupling with the modified catalyst provides additional advantages to designs where a catalyst in suspension is used. The optimal parameter of rotation was 54 rpm and the submerged surface of the disks offer a total contact area of 387 M². The modified solid showed a decrease in the value of its bandgap compared to commercial titanium. The system has a semi-automatic operation with a maximum reaction time of 50 h. Photo-activity tests show high conversion rates at low concentrations. The results conform to the Langmuir heterogeneous catalysis model.

The experience of ego dissolution and self-transcendence induced by psychedelic substances offers a profound challenge to our conventional understanding of the self and our relationship with the natural world. This paper delves into the philosophical underpinnings and implications of this phenomenon, exploring how the temporary breakdown of ego boundaries during a psychedelic experience may foster a sense of profound interconnectedness with nature. Drawing from Western and Eastern philosophical traditions, as well as recent insights from neuroscience and consciousness studies, we examine the potential of psychedelic-induced self-transcendence to catalyze a shift in our perspectives on the human-nature relationship. The paper investigates the philosophical implications of this experience, including its resonance with deep ecological philosophies and its potential to inspire more ecocentric ethical frameworks. Furthermore, we explore the possible practical implications of fostering a sense of ecological connectedness through psychedelics, such as promoting environmentally sustainable behaviors and addressing the pressing challenges of climate change and ecological degradation. Ultimately, this exploration highlights the value of engaging with altered states of consciousness as a means to reconsider our place within the intricate web of life on Earth.

This study describes all the properties of high T_c cuprates by introducing rotating holes that are created by angular momentum conservations on a 2D CuO₂ surface, and which have a different mass from that of a normal hole because of the magnetic field energy induced by the rotation. This new particle called a macroscopic Boson describes the doping dependences of pseudo-gap temperature and the transition temperature at which an anomaly metal phase appears and describes the origin of the pseudo-gap. Furthermore, this study introduces a new model to handle many-body interactions, which results in a new statistic equation. This statistic equation describing many-body interactions accurately explains why high T_c cuprates have significantly high critical temperatures. Moreover a partition function of macroscopic Bosons describes all the properties of anomaly metal phase, which sufficiently agree with experiments, using the result from our previous study [1] that analytically describes the doping dependence of T_c. By introducing a macroscopic Boson and the new statistical model for many-body interactions, this study uncovered the mystery of high T_c cuprates, which have been a challenge for many researchers. An important point is that, in this study, pure analytical calculations are consistently conducted, which agree with experimental data well (i.e., they do not use numerical calculations or fitting methods but use many actual physical constants).

We consider the Dirac electron as a nonperturbative particle-like solution consistent with its own Kerr-Newman (KN) gravitational and electromagnetic field. We develop the earlier models of the KN electron regularized by Israel and López, and consider the non-perturbative electron model as a bag model formed by Higgs mechanism of symmetry breaking. The López regularization determines the unique shape of the electron in the form of a thin disk with a Compton radius reduced by 4π. In our model this disk is coupled with a closed circular string which is placed on the border of the disk and creates the caused by gravitation frame-dragging string tension produced by the vector potential of the Wilson loop. Using remarkable features of the Kerr-Schild coordinate system, which linearizes the Dirac equation, we obtain solutions of the Dirac equation consistent with the KN gravitational and electromagnetic field, and show that this solution takes the form of a massless relativistic string. Parallelism of this model with quantum representations in Heisenberg and Schrodinger pictures explains remarkable properties of the stringy electron model in the relativistic scattering processes.

As paradigm of complex behavior, Self-organized Criticality (SOC) reflects the ability of nonequilibrium dynamical systems to self-adjust into metastable states that are scale independent. The goal of this report is to tentatively show that the hierarchy of Standard Model masses and mixing angles follows from the universal scaling attributes of SOC.

Online education allows learners to develop knowledge and skills flexibly and conveniently—such observation among students whose characteristics involve student engagement, self-regulation, and self-efficacy. However, studies to characterize Filipino online learners seem lacking. Thus, this study aimed to characterize science education tertiary students in the Philippines concerning their online student engagement (OSE), self-regulated learning (SRL), and online learning self-efficacy (OLSE). The unprecedented events brought by COVID-19 pandemic also urged the implementation of online modalities while there is no available information on students’ online learning profiles. Hence, researchers used a survey research employed through ex post facto approach to determine the effects of the demographic profile on OSE, SRL, and OLSE. The survey was participated by N=373 respondents who answered the questionnaire with informed consent administered via Google Forms. Results revealed that OSE indicators moderately characterized students, while SRL and OLSE indicators are true of them, substantiated by the overall mean M=3.85(SD=0.90), M=3.86(SD=0.92), and M=3.14(SD=0.73), respectively. Also, multivariate tests showed no significant effect among the independent groups (p&gt;0.05), except for gender and OLSE interaction (p&lt;0.05) so, only in OLSE was a significant difference found in gender. In conclusion, Filipino online learners are moderate across aspects of student engagement, self-regulation, and self-efficacy.

An event occurring within a stationary environment, in the direction toward which an observer self-rotates, is perceived to precede a simultaneous event, in the direction away from which she moves. When self-rotation results from angular acceleration in the dark, perception of space is also distorted, such that the subjective straight-ahead shifts in the opposite direction to motion and temporal event promotion. A reference frameshift theory, based on the special theory of relativity, is proposed to explain these findings. Here, a hyperbolic tangent transformation of objective angular velocity constrains subjective self-rotation velocity within finite bounds, consistent with it being a limited perceptual resource. Identifying this subjective variable with vestibular nystagmus slow-phase angular velocity, the asymptotic perceived self-rotation velocity is estimated at ~200 °⁄s. When included in the Lorentz transformations of the new formalism, this value predicts experimental simultaneity distortion. Hypothetically, the hyperbolic tangent objective-to-subjective transfer function would maximize the differential entropy of the percept, and thereby also the stimulus/percept mutual information, if angular velocities of body rotation encountered in naturalistic environmental interaction have a logistic probability density distribution of scale 100 °⁄s, a proposed experimental test of the scheme.

Self-assembly is a spontaneous process through which macroscopic structures are formed from basic microscopic constituents (e.g. molecules or colloids). By contrast, the formation of large biological molecules inside the cell (such as proteins or nucleic acids) is a process more akin to self-organization than to self-assembly, as it requires a constant supply of external energy. Recent studies have tried to merge self-assembly with self-organization by analyzing the assembly of self-propelled (or active) colloid-like particles whose motion is driven by a permanent source of energy. Here we present evidence that points to the fact that self-propulsion considerably enhances the assembly of polymers: self-propelled molecules are found to assemble into polymer-like structures, the average length of which increases towards a maximum as the self-propulsion force increases. Beyond this maximum, the average polymer length decreases due to the competition between bonding energy and disruptive forces that result from collisions. The assembly of active molecules might have promoted the formation of large pre-biotic polymers that could be the precursors of the informational polymers we observe nowadays.

The phenomenon of dissipative self-organization is studied on the example of time-crystal networks. Particular attention was given to transient processes, attractor topologies, phase transitions, and asymptotic stability. New concepts were introduced, including topological phases, spinorial states, and bond flavors. Concepts such as ground states, chemical potentials, elastic forces, temperature, and statistical distributions were endowed with a new meaning associated with asymptotic stability. Phenomena usually attributed exclusively to quantum physics have been shown to occur in this essentially classical environment. They coexist with, and in some cases, such as charge quantization, are related to the phenomenon of time dilation. The approach was applied to model vacuum self-organization. We have shown that under the ac-tion of competing forces, such as gravity and antigravity, a cascade of phase transitions can transform an unorganized vacuum into phases in which interactions, fields and waves resemble electromagnetic, weak, and strong, and their elements can be used as building blocks for prototype particles. In addition, some interrelation field parameters and probabilities of particle transmutations were calculated, which are not predicted by the standard model. The results are consistent with the experiment. The presented material and methodology may be of interest for studying self-organization in different environments.

The Munich ChronoType Questionnaire (MCTQ) has now been available for more than 15 years; its original publication has been cited 1,240 times (Google Scholar, May 2019); its online version, which was available until July 2017, has produced almost 300,000 entries from all over the world (MCTQ database). The MCTQ has gone through several versions, has been translated into 13 languages and has been validated against other more objective measures of daily timing in several independent studies. Besides being used as a method to correlate circadian features of human biology with other factors – ranging from health issues to geographical factors – the MCTQ gave rise to quantifying old wisdoms, like “teenagers are late” and has produced new concepts, like social jetlag. Some like the MCTQ’s simplicity and some view it critically; it is time to have a self-critical view on the MCTQ, to address some misunderstandings and give some definitions about MCTQ-derived chronotype and the concept of social jetlag.

Vitrimers are covalent network materials, comparable in structure to classical thermosets. Unlike normal thermosets, they possess a chemical bond swap mechanism that makes their structure dynamic and suitable for activated welding and even autonomous self-healing. The central question in designing such materials is the trade-off between autonomy and material stability: The swap mechanism facilitates the healing but it also facilitates creep, which makes the perfectly stable self-healing solid a hard goal to reach. Here, we address this question for the case of self-healing vitrimers made from star polymers. Using coarse-grained molecular dynamics simulations, we study the adhesion of two vitrimer samples and find that they bond together on timescales that are much shorter than the stress relaxation time. We show that the swap mechanism allows the star polymers to diffuse through the material through coordinated swap events, but the healing process is much faster and does not depend on this mobility.

To solve the problem of a uneven load for a dual-input counter-rotating transmission system, this research is based on Small Displacement Torsor Jacobian-Torsor theory.Considering the influence of the local parallel chain of a gearbox on the calculation accuracy of the backlash,the processing method of a meshing tooth pair parallel chain is proposed. The probability distribution of the tolerance band of gearbox manufacturing and assembly errors is modeled, the three-dimensional tolerance analysis model of a dual-input counter-rotating gearbox is established, and the Monte Carlo method is used to solve the backlash of the output end. The output backlash is solved with the Monte Carlo method, and the theoretical design backlash is combined with the output backlash to derive the gearbox side clearance range. The gearbox shaft system is analyzed statically, the range of the equal load coefficient is calculated, and the equal load performance optimization method based on the matching relationship between the gear backlash and the elastic shaft torsional stiffness is proposed. The correctness of the three-dimensional tolerance analysis combined with the elastic deflection angle used to optimize the equal load performance of the dual-input counter-rotating transmission system is verified by comparison with the relevant test data.

The present article investigates the threshold analysis of yielding in a variable thickness rotating disk based on the Tresca criterion. The analysis is conducted on a Functionally Graded Material (FGM) constructed from tailored materials, following the theory of small deformations and for the case of plane stress. The elasticity modulus, density, and yield stress are assumed to be power functions of the radial coordinate. Poisson’s ratio is considered constant due to small variations in different materials. Additionally, the governing equation for the rotating disk is solved analytically. Besides the material type, another factor affecting the distribution of effective stress magnitudes is the cross-sectional shape (profile) of the disk. The thickness of the cross-sectional disk varies radially as a power function. In the current analysis, different conditions for the onset of yielding and the evolution of plastic flow are considered. For evaluation and validation, the obtained results are compared and validated against similar results for specific cases (homogeneous disk and constant thickness graded disk) available in previous references. The results indicate that considering variable thickness for the disk section significantly affects the stresses and the location of the initiation of yielding

The vibration propagates in a media such as a shaft in the form of elastic waves. The propagation characteristics of the waves are affected by the geometry of the media, the material properties as well as the cracks. The study to elastic waves propagating in a shaft with transverse cracks can help to detect them. The transverse crack possesses different crack modes due to different external loads. The influence of the crack mode, the location and the depth to the propagation characteristics is investigated in this paper. Firstly, the local flexibility coefficients with three different modes are deduced. And then, the transfer matrix of the elastic wave can be obtained. Finally, the influence of the crack mode, the location and the depth of the transverse crack as well as the rotating speed to the propagation characteristics is then studied, both in a numerical and an experimental way. It’s found that mode III is the most suitable mode in this paper, the location of the crack will make the stopbands fluctuating, the depth mainly affects the bandwidth of the stopbands, and the increase of the rotating speed will shift up the stopbands without changing their bandwidths.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

Knowledge about laminar-turbulent transition on operating multi-megawatt wind turbine blades needs sophisticated equipment like hot-films or microphone arrays. Contrarily thermographic pictures can easily be taken from the ground and temperature differences indicate different states of the boundary layer. The accuracy however, still is an open question, so that an aerodynamic glove known from experimental research on aero-planes was used to classify the boundary-layer state of a 2 megawatt wind turbine blade operating in the orthern part of Schleswig-Holstein, Germany. State-of-the-art equipment for measurering static surface pressure was used for monitoring the lift distribution. To distinguish laminar and turbulent parts of the boundary layer (suction side only) 48 microphones were applied together with ground-based thermographic cameras from two teams. Additionally, an optical camera mounted on the hub was used to survey vibrations. During start-up (from 0 to 9 rpm) extended, but irregularly shaped regions of a laminar boundary layer were observed which had the same extension measured both with microphones and Thermography. When an approximately constant rotor rotation (9 rpm corresponding to approximately 6 m/s wind-speed) was achieved, a flow transition was visible at the expected position of 40 % chord length on the rotor blade, which was fouled with dense turbulent wedges and an almost complete turbulent state on the glove was detected. In all observations, quantitative determination of the flow transition positions from thermography and microphones agree well within their accuracy.

Secure attachment, developed through consistent relationships with attachment figures in childhood, is a crucial factor in fostering healthy interpersonal relationships and a positive self-perception. This research aimed to assess how perceived security, as an indicator of secure attachment, predicts adult self-concept through the mediating effects of resilience and positive self-esteem. A quantitative, cross-sectional, and non-probabilistic study was conducted with 383 participants, of whom 76.2% were females, aged between 17 and 86 years (M = 28.52, SD = 12.23). Correlational analyses revealed significant positive associations between perceived security, self-concept, resilience, and positive self-esteem. Path analysis demonstrated that resilience and positive self-esteem sequentially mediate the relationship between perceived security during childhood and adult self-concept (Total Effect R2 = .34, F(1,381) = 193, p < .001; Indirect effect of sequential mediation b = .02, CI 95% [.01, .04]). Findings suggest that the ability to cope with ad-versity and personal acceptance underlie the impact of perceived security on self-concept. It is recommended to promote not only secure attachment in family interventions but also resilience and self-esteem in programs targeting adolescents, youth, and adults.

Background and Objectives: Elders’ needs are rarely examined beforehand, and thus, although technology-based tools can enhance self-management, acceptability rates are still low. This study aimed to examine and compare self-reported needs, priorities, and preferences of elders with heart failure (HF), diabetes mellitus (DM), and chronic obstructive pulmonary disease (COPD) toward technology use to enhance self-management. Materials and Methods: A convenience sample of 473 participants over 60s (60.5% females), diagnosed with HF (N=156), DM (N=164), or COPD (N=153) was recruited. They were administered a questionnaire about the usefulness of technology in general and in specific areas of disease management. Results: Most participants (84.7%) admitted that technology is needed for better disease management. This was equally recognized across the three groups both for the overall and specific areas of disease management (in order of priority: ‘Information’, ‘Communication with Physicians &amp; Caregivers’, and ‘Quality of Life &amp; Wellbeing’). Sociodemographic differences were found. Cell phones and PCs were the devices of preference. The four common features prioritized by all three groups were related to ‘information about disease management’ (i.e., monitoring symptoms, reminders for medication intake, management and prevention of complications), whereas the fifth one was related to ‘communication with physicians and caregivers (i.e., in case of abnormal or critical signs). The top disease-specific feature was also monitoring systems (of respiratory rate or blood sugar or blood pressure, oxygen), whereas other disease-specific features followed (i.e., maintaining normal weight for HF patients, adjusting insulin dose for DM patients, and training on breathing exercises for COPD patients). Conclusions: Elders in these three samples seem receptive to technology in disease management. mHealth tools, incorporating both common and disease-specific features and addressing different chronic patients, and being personalized at the same time, could be cost-saving and useful adjuncts in routine clinical care to improve self-management.

Self-compacting concrete is essential for vertical structures due to high reinforcement and usage of pumps for transporting the concrete at the working site. SCC is mainly influenced by self-curing for arid areas. To explore the SCC (Self-Compacting Concrete) mixture and condition influencing the self-curing condition were determined using the experimental procedure. Determination of various parameters was done using T50 slump flow, V-funnel, L-box-box, J ring test, compressive strength, splitting tensile strength, and flexural strength test. After the experimental investigation, it shows that if the dose if the dosage of superplasticizer (SNF%) increases, it will improve the concrete mixture's different properties, such as flowability and ability to pass. Higher water-to-cement ratios (w/c) generally result in enhanced flowability and stability. Mixture 9 (SNF 0.35, w/c 0.5) demonstrates favourable results across all parameters, indicating excellent flowability and stability. Mixture 9 (SNF 0.35, w/c 0.5) also shows favourable flowability and stability characteristics. Lower concentrations, such as 0.5%, may have a positive effect up to a certain point but might not provide sustained improvement over the curing period. On the other hand, concentrations of 1% and 2% demonstrated consistent and significant enhancement in strength throughout the 28 days. It is found that the higher concentrations of PEG 4000 may be more effective in improving the material strength.

Self-report measurement is frequently used in human sports to assess training adaptations [1, 2]. This is a technique novel to the equestrian sport. The aim of this study was to describe how elite event riders of Germany evaluate their own fitness as well as that of their horses for the entire duration of an eventing season. Additionally, correlations with possible influencing external factors such as type of training or duration of grazing were also investigated. Short online questionnaires were used to allow eight riders to describe the training of their horses. Five criteria (general performance, ability to concentrate, general state of mind, general muscular condition and emotional wellbeing) were used to assess both, their horse's, as well as their own wellbeing. A 1-10 rating scale was used to score each criterion resulting in an average of 38 points out of 50 (maximum wellbeing) for horse (Std. dev. 0.55) and rider (Std. dev. 0.65) respectively. A total of 120 questionnaires were analysed. A correlation could be demonstrated (Spearman's correlation coefficient = 0.5) between rider and horse score, whereby it only became a linear correlation above 30 points. In addition, the horse score correlates positively with its success at competitions. While the horses were rated similarly throughout the season, the riders’ perceived welfare was higher in the middle of the season compared with the beginning and end of the season. Regularly turned-out horses resulted in higher horse scores (Linear mixed model, p=0,04, n=120). It can be concluded that the self-report measurement of fatigue and wellbeing can be a useful tool for trainers and riders to better determine the horse’s fatigue and recovery. It should be noted that external factors influence both, rider and horse assessment.

Background: Student-specific stress is pervasive and impairs health and attainment. Experimentally induced self-affirmation can reduce stress, but little is known about the mechanisms underlying this effect, and the role of individual differences. The present study explores the relationship between spontaneous self-affirmation, student-specific stress, and overlapping constructs of positive self-regard during the COVID-19 pandemic. Methods: The study investigated inter-relationships between spontaneous self-affirmation, student-specific perceived stress and potential covariates including self-esteem, self-integrity and habitual positive self-thought. University students (N = 151) aged 18 to 50 responded to an online questionnaire including the Spontaneous Self-Affirmation Measure, College Student Stress Scale, Rosenberg Self-Esteem Scale, Habitual Index of Positive Thinking and Self-Integrity Scale. Results: Unexpectedly, regression analysis revealed that spontaneous self-affirmation was a positive predictor of student-specific stress, seemingly driven by relational affirmations. Self-esteem and habitual self-thought were negative predictors of student-specific stress, whilst self-integrity was not a predictor. Conclusions: Habitual positive self-thought may offer a sustainable solution to student-specific stress, but spontaneous self-affirmation does not. A reduction in defensive responses, elicitation of negative emotions, or use of conditional relationships in relational affirmation

In this paper, dual-rotor counter-rotating (CR) configurations of vertical axis wind turbines (VAWT) are briefly inspected and divided into three types. This investigation was focused on one of these types – the CR-VAWT with co-axial rotors, in which two equal rotors are placed on the same shaft, displaced from each other along it and rotate in opposite directions. For this CR-VAWT with three-blade H-Darrieus rotors, the properties of the design in terms of aerodynamics, mechanical transmission and electric generator, as well as control system are analyzed. A new direct-driven dual-rotor (DR) permanent magnet synchronous generator (PMSG) was proposed, in which two built-in low-power PM electric machines have been added. They perform two functions – start-up and overclocking of the rotors to the angular velocity at which the lifting force of the blades is generated and stabilizing the CR-VAWT work as wind gusts act on the two rotors. Detailed in this paper is the evaluation of aerodynamic performance of the CR-VAWT via 3D computational fluid dynamics (CFD) simulations. The evaluation was conducted using the CONVERGE CFD software with the inclusion of the actuator line model for the rotor aerodynamics, which significantly reduces the computational effort. Obtained results show that both rotors, while they rotate in opposite directions, had a positive impact on each other: the power coefficients of the upper and lower rotors in the CR-VAWT increased by 5.5% and 13.3% respectively compared to the single-rotor VAWT at the optimal distance between the rotors of 0.3 from a rotor height.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

Computational fluid dynamics is used to study the impact of the support structure of a tidal turbine on performance and the downstream wake characteristics. A high-fidelity computational model of a dual rotor, contra-rotating tidal turbine in a large channel domain is presented, with turbulence modelled using large eddy simulation. Actuator lines represent the turbine blades, permitting the analysis of transient flow features and turbine diagnostics. The following four cases are considered: the flow in an unexploited, empty channel; flow in a channel containing the rotors; flow in a channel containing the support structure; and flow in a channel with both rotors and support structure. The results indicate that the support structure contributes significantly to the behaviour of the turbine and to turbulence levels downstream, even when the rotors are upstream. This implies that inclusion of the turbine structure, or some parametrisation thereof, is a prerequisite for the realistic prediction of turbine performance and reliability, particularly for array layouts where wake effects become significant.

In the Vietnamese Mekong delta, soil quality and crop yield are steadily declining under rice monocultures with three crops per year. The objective of this study was to evaluate the medium-term effects of rotating rice with upland crops and adding organic amendments on rice yield and relate it to soil quality. A field trial with split-plot design including two factors and three replicates was carried out from 2017 to 2020, over the course of nine consecutive cropping seasons. Crop rotations and organic amendments were applied as main-plot and subplot factors, respectively. The rotations were: 1) rice–rice–rice (R–R–R), 2) soybean–rice–rice (So–R–R), and 3) sesame–rice–rice (Se–R–R), while organic amendment treatments included: i) no amendment (NO-AM); ii) compost of rice straw and cow manure (RS+CM), and iii) sugarcane compost (SGC); the composts were applied at a rate of 2.0 t ha-1. The rotation cycle started with the so-called spring–summer (SS), followed by summer–autumn (SA) and ended with the winter–spring (WS) season. Rice yield significantly (P &lt; 0.05) increased by organic amendments after nine growing seasons (2019–2020 WS), with an increment of 5.1% for RS+CM (7.07 ton/ha) and 6.1% for SGC (7.14 ton/ha). Contrary to our expectation, rotations with upland crops did not significantly increase rice yield. Rice yield significantly and positively correlated with an integrated soil quality index SQI (r = 0.86) for the topsoil (0–15 cm), but not for the subsoil (15–30 cm). The increased availability of soil nutrients (Si and marginally also P) and improved soil physical properties probably induced by organic amendments, along with other soil properties under study, cumulatively attributed to enhanced rice yield. Use of a SQI involving several soil quality indicators enables to overall quantify the importance of soil fertility for rice yield versus other factors and it provides an effective means of quantifying the integrated effect of improved management. Moreover, integrating a wide range of soil quality indicators in a SQI ensures its applicability across diverse settings, including different crop rotations and various soil types.

Self-sustained learning (SSL) is considered a crucial factor in promoting students’ long-term learning and development in a sustainable society. To deepen the understanding of SSL, especially in the context of learning English as a second language, the current study examined the influence of intercultural communicative skills, language mindset, and positive L2 self on SSL in English learning among 1,238 college students in China. The results showed that students not only had a strong language mindset, positive L2 self, and intercultural communicative skills but also scored higher in long-term self-sustained English learning. Findings from the Structural Equation Modeling indicated that both language mindset and intercultural communicative skills positively predicted positive L2 self and self-sustained English learning. Furthermore, language mindset and intercultural communicative skills had an indirect impact on self-sustained English learning through positive L2 self. These findings suggest that to promote English learners’ SSL, instructors should help facilitate students’ intercultural communicative skills and foster a growth language mindset, as well as positive language learning beliefs.

The gradient descent algorithm has become the standard algorithm for computing the extreme values of functions, but for multivariate functions this algorithm is mostly ineffective. This is because the convergence rate of each element is inconsistent in most cases. However, in this paper, we found that the gradient sign is a self-optimizing operator, ensuring that the convergence rate is consistent across all elements. This also explains, from an optimization perspective, the success of the Fast Gradient Sign Method (FGSM) in generating adversarial samples that are indistinguishable from the normal input, but can easily fool neural networks. We also found that the fractional order gradient is also self-optimizing, and that the convergence speed of this algorithm can be controlled by adjusting the order of the gradient. Experiments suggest that this algorithm not only generates adversarial samples faster than other algorithms, but that a single source image can generate many such samples. This algorithm is also more effective than others at generating adversarial samples from simple images.

Body Expression (BE) has been defined in the past decades as a discipline within Physical Education (PE) with very particular characteristics and a strong emotional component. In this study, a programme of this discipline was applied to university Physical Activity and Sports Sciences (PASS) students from six consecutive academic years: three prior to and three during the pandemic. A pre-post design was used to determine how the BE programme affected the university students' self-concept (SC). To do so, a questionnaire with a multidimensional approach to this construct was administered, whose dimensions were closely related to the BE programme's characteristics. The results revealed significant improvements in the final SC, compared to the initial SC. Men reported lower SC values than women before the programme implementation, but higher at the end. Therefore, the change was larger in men, so the programme may have had an equalising effect between groups. It was also verified that the pandemic had particularly affected women.

Biological systems often need to operate in complex environments where conditions can rapidly change. This is possible due to their inherent ability to sense changes and adapt their behavior in response. Here, we detail recent advances in the creation of synthetic genetic parts and circuits whose behaviors can be dynamically tuned through a variety of intra- and extra-cellular signals. We show how this capability lays the foundation for implementing control engineering schemes in living cells and allows for the creation of biological systems that are able to self-adapt, ensuring their functionality is maintained in the face of varying environmental and physiological conditions. We end by discussing some of the broader implications of this technology for the safe deployment of synthetic biology.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

Self-consciousness can be considered as the internal disposition to direct attention to oneself. This dispositional tendency can be focused on private aspects of the self, but also on public characteristics of the individual. We examine self-consciousness in online consumer behavior. This concept has been poorly investigated in consumer research. The main objective of this paper is to analyze the influence of the dimensions of self-consciousness in consumer adoption of online shopping. This study is based on a sample of 725 Spanish undergraduates. Results indicated that public self-consciousness is a significant predictor of the adoption of online shopping.

Living organisms are active open systems far from thermodynamic equilibrium. The ability to behave actively corresponds to dynamical metastability: minor but supercritical internal or external effects may trigger major substantial actions such as gross mechanical motion, dissipating internally accumulated energy reserves. Gaining selective advantage from beneficial use of activity requires a consistent combination of sensual perception, memorised experience, statistical or causal prediction models, and resulting favourable decisions on actions. This information processing chain originated from mere physical interaction processes prior to life, here denoted as structural information exchange. From there, the self-organised transition to symbolic information processing marks the beginning of life, evolving by novel purposivity of trial-and-error feedback and accumulation of symbolic information. The emergence of symbols and prediction models can be described as a ritualisation transition, a symmetry-breaking kinetic phase transition of the 2^nd kind previously known from behavioural biology. The related new symmetry is the neutrally stable arbitrariness, conventionality or code invariance of symbols with respect to their meaning. The meaning of such symbols is given by the structural effect they ultimately unleash, directly or indirectly, by deciding on which actions to take. The early genetic code represents the first symbols. The genetically inherited symbolic information is the first prediction model for activities sufficient for survival under the condition of environmental continuity, sometimes understood as a “final causality” property of the model.

We show that quantum mechanics can be constructed as a classical field theory that correctly describes all basic quantum effects, by combining the Maxwell and Dirac equations. It is shown that for a self-consistent union of the Maxwell and Dirac equations into a unified classical field theory, it is necessary to introduce an additional short-range tensor field, which compensates the intrinsic electrostatic field of the electron wave inside the atom. For the combined Maxwell-Dirac field, the stress-energy tensor is constructed. We show that in the nonrelativistic limit this theory naturally transforms into the self-consistent Maxwell-Pauli theory and allows describing all basic quantum effects in the framework of classical field theory without any quantization.

The development and qualification of CrAlN coatings deposited by DC magnetron sputtering offer new industrial solutions to increase the lifecycle of material forming tools (machining and shaping). This study focuses on the selection and optimization of deposition modes for CrAlN layers to be deposited on a 90CrMoV8 tool steel substrate. The adopted methodology aims to optimize the deposition conditions to meet the customer's requirement of a CrAlN coating thickness of approximately 2-3 µm for use in a hot forming process. Different polarizations using two Al and Cr targets, with both stationary and rotating substrate modes during deposition, were tested and evaluated. Characterizations of the CrAlN coating layers (microhardness, residual stress, structures) and performance in service (wear, friction, adhesion, corrosion) were chosen as selection criteria for a particular coating mode. The aluminum content plays a crucial role in the tribological and mechanical behavior of CrAlN layers. Corrosion resistance is more sensitive to the aluminum content for the stationary deposition mode. As a result, the rotating mode provides higher adhesion (+100%) and less wear (-60%) compared to the stationary mode. Therefore, depending on the likely performance in service, either a stationary or rotating mode could be applied for coating the functional surfaces of hot forming tools.

With the advancing energy transition, ice is a growing problem in wind turbine sector. The development of systems to detect and mitigate icing makes it necessary to understand its basic behavior and characteristics. This paper proposes a method for the continuous and full field measurement of the icing process of rotating blades, using a single line laser profile scanner. Inside of a climate chamber, a rotor is driven by a motor, while a system of nozzles provides a fine water dust, which leads to ice accumulating on simple NACA blades, that in turn is measured by a triangulation laser. The measurement data is cleared from outliers and presented as a surface in 3D space. An alpha shape is used to reconstruct and extract the volume of the ice between a reference and a measurement surface, using the corresponding Matlab function. Appropriate input parameters for the function and offsetting of the reference surface to improve the results are compared and discussed. The resulting system is able to detect thin changes in the ice layer in the range of sub millimeter thickness.

The hypothesis posed was whether participation in LaLiga Genuine Santander (competitive football) influenced the quality of life (QL) of the people who participated in it, since their perception of themselves is enhanced by all the aformentioned factors (self-determination, social inclusion, emotional well-being, physical well-being, material well-being, rights, personal development, interpersonal relationships). The objective was to evaluate the QL of people with Down's Syndrome (DS) using their self-perception (n=39) and the perception of the informants (family members, teachers) (n=39). The KidsLife-Down Scale, with a few modifications was used. In general, differences of opinion between the subgroups of participants with DS and informants showed that results were higher in terms of perception for participants in the DS subgroup. Scores for all variables were higher for those participants with DS who said they did engage in practicing competitive football. Despite the perception of informants provides a great deal of information regarding the QL of participants with DS, the latter should be involved in the evaluation process and their self perceptions taken into account. Our research shows that participation in the league modifies the perceptions of the participants with Down's Syndrome regarding their quality of life. However, these perceptions are not shared by the informants.

This paper introduces the novel concept of Time-Traveling Turing Machines (TTTMs) — Turing Machines with the ability to read symbols that have been explicitly sent from their future computational state. We delve into their properties and behavior, particularly emphasizing the importance of maintaining a self-consistent computational timeline. We present theorems demonstrating the universality of these machines and the challenges in achieving faster computations than traditional Turing Machines.