In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

We present a generic and open-source framework for the numerical modeling of the expected transport and storage mechanisms in unconventional gas reservoirs. These unconventional reservoirs typically contain natural fractures at multiple scales. Considering the importance of these fractures in shale gas production, we perform a rigorous study on the accuracy of different fracture models. The framework is validated against an industrial simulator and is used to perform a history-matching study on the Barnett shale. This work presents an open-source code that leverages cutting-edge numerical modeling capabilities like automatic differentiation, stochastic fracture modeling, multi-continuum modeling and other explicit and discrete fracture models. We modified the conventional mass balance equation to account for the physical mechanisms that are unique to organic-rich source rocks. Some of these include the use of an adsorption isotherm, a dynamic permeability-correction function, and an embedded discrete fracture model (EDFM) with fracture-well connectivity. We explore the accuracy of the EDFM for modeling hydraulically-fractured shale-gas wells, which could be connected to natural fractures of finite or infinite conductivity, and could deform during production. Simulation results indicates that although the EDFM provides a computationally efficient model for describing flow in natural and hydraulic fractures, it could be inaccurate under these three conditions: 1. when the fracture conductivity is very low. 2. when the fractures are not orthogonal to the underlying Cartesian grid blocks, and 3. when sharp pressure drops occur in large grid blocks with insufficient mesh refinement. Each of these results are very significant considering that most of the fluids in these ultra-low matrix permeability reservoirs get produced through the interconnected natural fractures, which are expected to have very low fracture conductivities. We also expect sharp pressure drops near the fractures in these shale gas reservoirs, and it is very unrealistic to expect the hydraulic fractures or complex fracture networks to be orthogonal to any structured grid. In conclusion, this paper presents an open-source numerical framework to facilitate the modeling of the expected physical mechanisms in shale-gas reservoirs. The code was validated against published results and a commercial simulator. We also performed a history-matching study on a naturally-fractured Barnett shale-gas well considering adsorption, gas slippage & diffusion and fracture closure as well as proppant embedment, using the framework presented. This work provides the first open-source code that can be used to facilitate the modeling and optimization of fractured shale-gas reservoirs. To provide the numerical flexibility to accurately model stochastic natural fractures that are connected to hydraulically-fractured wells, it is built atop other related open-source codes. We also present the first rigorous study on the accuracy of using EDFM to model both hydraulic fractures and natural fractures that may or may not be interconnected.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

Innovations and improvements in hydraulic fracturing and horizontal well technologies have contributed to the success of the shale gas industry; however, the industry is also challenged by freshwater use and environmental health issues. Increasing water impact makes precise quantification of water consumption important. The objective in this study was to better understand water sustainability and availability of the projected shale gas from 2018 to 2030 in the Weiyuan play, China. The water footprint framework was used to quantify the potential water use and environmental impacts on different time scales. The results showed that the water use per well ranged from 11351.3 to 60664.73 m3, with a median of 36013.94 m3, totaling ~3.44 Mm3 for 97 wells. Yearly evaluation results showed that the gray water footprint was the main contributor and accounted for 83.82% to 96.76%, which was dependent on different scenarios of treatment percentages. The monthly environmental impact results indicated that the annual streamflow statistics were more likely to prevent water withdrawal. Water quality issues may be alleviated through recycling and retreatment measures that improve current waste water management strategies. Resource regulators should manage their water resources by matching water demand to water availability or replenishment.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

This study aimed to analyse the variation of recreational water quality in Plettenberg Bay in an attempt to comprehend the effects of pollution on the environment, and more specifically the potential impacts on the quality of surface water used for recreational activities. Plettenberg Bay is a major destination for tourists in South Africa, with recreational water activities representing an important attraction. For this study, data were obtained from Bitou Municipality, the local au-thority in charge of the water monitoring program in Plettenberg Bay. The selected datasets contained water quality data collected by the Bitou Municipality waterworks department in three sampling sites in Plettenberg Bay. The samples were tested for six water quality parameters namely, Ammonia, Suspended Solids, Conductivity, Nitrates/Nitrites, pH, and E coli. Water quality trends appeared stabile over the five years, with only a few parameters showing variation in their concentration levels. It is recommended that the Bitou Municipality increase the sampling frequency to allow a clearer understanding of water quality variation and to minimise potential uncertainties.

Shale gas content is the key parameter for shale gas potential evaluation and favorable area prediction. Therefore, it is very important to determine shale gas content accurately. Generally, we use the USBM method for coal reservoirs to calculate gas content of shale reservoirs. However, shale reservoirs are different from coal reservoirs in depth, pressure, core collection, etc. This method would inevitably cause problems. In order to make the USBM method more suitable for shale reservoir, an improved USBM method is put forward on the basis of systematic analysis of core pressure history and temperature history during shale gas desorption. The improved USBM method modifies the calculation method of the lost time, and determines the temperature balance time of water heating. In addition, we give the calculation method of adsorption gas content and free gas content, especially the new method of calculating the oil dissolved gas content and water dissolved gas content which are easily neglected. We used the direct method (USBM and the improved USBM) and the indirect method (adsorption gas, free gas and dissolved gas) to calculate the shale gas content of 16 shale samples of the Triassic Yanchang Formation in the Southeastern Ordos Basin, China. The results of the improved USBM method show that the total shale gas content is high, with an average of 3.97 m³/t, and the lost shale gas content is the largest proportion with an average of 62%. The total shale gas content calculated by the improved USBM method is greater than that of the USBM method. The results of the indirect method show that the total shale gas content is large, with an average of 4.11 m³/t, and the adsorption shale gas content is the largest proportion with an average of 71%. The oil dissolved shale gas content which should be taken attention accounts for about 7.8%. The relative error between the improved USBM method and indirect method is much smaller than that between USBM method and indirect method, which verifies the accuracy of the improved USBM method.

Hydraulic fracturing in shale gas reservoirs has usually resulted in complex fracture network. The results of micro-seismic monitoring showed that the nature and degree of fracture complexity must be clearly understood to optimize stimulation design and completion strategy. This is often called stimulated reservoir volume (SRV). In the oil & gas industry, stimulated reservoir volume has made the shale gas exploitation and development so successful, so it is a main technique in shale gas development. The successful exploitation and development of shale gas reservoir has mainly relied on some combined technologies such as horizontal drilling, multi-stage completions, innovative fracturing, and fracture mapping to engineer economic completions. Hydraulic fracturing with large volumes of proppant and fracturing fluids will not only create high conductivity primary fractures but also stimulate adjacent natural fractures. Fracture network forming around every hydraulic fracture yields a stimulated reservoir volume. A model of horizontal wells which was based on a shale gas reservoir after volume fracturing in China was established to analyze the effect of related parameters on the production of multi-fractured horizontal wells in this paper. The adsorbed gas in the shale gas reservoir is simulated by dissolved gas in the immobile oil. The key to simulate SRV is to accurately represent the hydraulic fractures and the induced complex natural fracture system. However, current numerical simulation methods, such as dual porosity modeling, discrete modeling, have the following limitations: 1) time-consuming to set up hydraulic and natural fracture system; 2) large computation time required. In this paper, the shape of the stimulated formation is described by an expanding ellipsoid. Simplified stimulated zones with higher permeability were used to model the hydraulic fracture and the induced complex natural fracture system. In other words, each primary fracture has an enhanced zone, namely SRV zone. This method saves much developing fine-grid time and computing time. Compared with the simulation results of fine-grid reference model, it has shown that this simplified model greatly decreases simulation time and provides accurate results. In order to analyze the impacts of related parameters on production, a series of simulation scenarios and corresponding production performance were designed. Optimal design and analyses of fracturing parameters and the formation parameters have been calculated in this model. Simulation results showed that the number of primary fractures, half length, SRV half-width and drop-down have great effects on the post-fracturing production. Formation anisotropies also control the production performance while the conductivity of the primary fractures and SRV permeability do not have much impact on production performance. The complexity of stimulated reservoir volume has strong effect on gas well productivity. Fracture number mainly affects the early time production performance. The increase of SRV width cannot enlarge the drainage area of the multi-fractured horizontal wells, but it can improve the recovery in its own drainage region. Permeability anisotropies have much effect on production rate, especially the late time production rate. The results prove that horizontal well with volume fracturing plays an irreplaceable role in the development of ultra-low permeability shale gas reservoir.

Recent scholarship highlights the significant environmental impact of the expanding hydraulic fracturing industry, necessitating up-to-date, comprehensive, national-scale assessments. Addressing this gap, this literature review provides a thorough analysis of the contamination and induced seismicity associated with shale-gas hydraulic fracturing in the United States. Employing systematic reviews of literature and federal reports up until July 2023, this study reveals multiple areas of concern. Notably, water and soil contamination, seismic activity, and air pollution are identified as significant challenges linked to shale gas extraction. However, ongoing studies are actively exploring remediation strategies, including advancements in monitoring and treatment technologies, aimed at mitigating the impact of contamination. These findings underscore the need for stringent regulations, continuous research, and effective management practices. This work emphasizes the importance of a collaborative approach that leverages field studies, experimental investigations, and computational advancements to ensure the responsible development of shale gas resources.

Analyses of the three predominant types of sedimentation – clastic, carbonate and black shale – revealed their discontinuity/continuity in different facies environments of the Middle and Late Devonian of the central part of the Volga-Urals petroleum province, namely (1) in depressions, both condensed and non-condensed, (2) on the slopes of depressions and (3) in shallow water environments represented by tectonic arches or localised biohermal uplifts. The regional zonation of conodonts, correlated with the global chronostratigraphic scheme, substantiates the stratigraphic completeness of the general Devonian sequence in this area. In particular, the sedimentation of organic-rich black shales, traditionally considered as source rocks, lasted more than 29 million years, starting from the Late Eifel and ending at the Devonian-Carboniferous boundary. There was only one hiatus in the deposition of both black shales and carbonate sediments, lasting about 2.5 million years at the end of the Frasnian. That interval is dominated by clastic sediments, which are considered to be the most productive reservoirs of the Volga-Ural province. In the time interval from the beginning of the Eifel to the end of the Frasnian (about 17 Ma), (a) clastic sediments show the highest accumulation rates; (b) the most complete sequences occur in depressions; and (c) arches and uplifts show the most significant gaps in the geological record. During Famennian, (a) clastic sedimentation has completely ceased; (b) differences between the slopes of troughs and shallow-water environments have diminished, resulting in stable accumulation of carbonate sediments in both settings; (c) the decrease in sequence thickness (up to 50 m) in depressions suggests reduced accumulation rates of deep-water organic-rich black shales. The results help to understand the complex spatial relationship between different coexisting sedimentation types and focus attention to the incompleteness of the geological record in different environments.

The grain-to-grain stress vertically in sediments is given by the overburden less the pore fluid pressure, σ, divided by the fraction of the horizontal area which is the supporting matrix , (1 − φ), where φ is the porosity. It is proposed that the fractional reduction of this ratio, Λ, with time is given by the product of φ 4m/3 , (1 − φ) 4n/3 , and one or more Arrhenius functions A exp(−E/RT ) with m and n close to 1. This proposal is tested for shale sections in six wells from around the world for which porosity-depth data are available. Good agreement is obtained above 30-40 C and porosities less than 0.5. Single activation energies for each well are obtained in the range 15-33 kJ/mole, close to pressure solution of quartz, 24 kJ/mol. Values of m and n are in the range 1 to 0.8, indicating nearly fractal pore-matrix spaces and water-wet interfaces. Results are independent of over- or under-pressure of pore water. This model explains shale compaction quantitatively. Given porosity-depth data and accurate activation energy, E, one can infer paleo-geothermal-gradient and from that organic maturity, thus avoiding unnecessary drilling.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

Shale gas reservoirs (SGR) are important replacements for conventional energy resources and have been widely exploited by hydraulic fracturing technologies. On the one hand, due to the inherent ultra-low permeability and porosity, there is stress sensitivity in the reservoirs generally. On the other hand, hydraulic fractures and the stimulated reservoir volume (SRV) generated by the massive hydraulic fracturing operation have contrast properties with the original reservoirs. These two phenomena bring huge challenges in SGR transient pressure analysis. Although some works in the literatures have been done on the transient pressure analysis of multi-fractured horizontal wells in SGR, unfortunately, none of them has taken the stress sensitivity and spatially varying permeability of SRV zone into consideration simultaneously. To fill this gap, this paper first idealizes the SGR to be four linear composite regions. What’s more, SRV zone is further divided into sub-sections on the basis of non-uniform distribution of proppant within SRV zone which easily yields spatially varying permeability away from the main hydraulic fracture. The stress sensitivity is characterized by the varying permeability depended on the pore pressure. By means of perturbation transformation and Laplace transformation, an analytical multi-linear flow model (MLFM) is obtained and validated by the comparison with the previous model. On the basis of our model, the flow regimes are identified and the sensitivity analysis of critical parameters are conducted to further understand the transient pressure behaviors. The research results provided by this work are of significance for well test interpretation and production performance analysis of SGR.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

Large-scale volumetric fracturing is generally used during shale gas development. The return rate of fracturing fluid is low, and a large amount of slickwater will be retained in the reservoir. The adsorption and desorption of partially hydrolyzed polyacrylamide (HPAM), an additive commonly used in slickwater, on the surface of shale was studied using Longmaxi Shale from the Sichuan Basin. The experimental results showed that the mass ratio of the HPAM solution to shale reached saturation adsorption at 20:1 when the concentration of HPAM solution was 1000 mg/L and 25:1 when the concentration of HPAM solution was 500 mg/L. The mass ratio of the HPAM solution to shale was fixed at 25:1, and the adsorption equilibrium was reached at a HPAM concentration of 1000 mg/L when the aqueous solution temperature was 30°C and 800 mg/L when the aqueous solution temperature was 60°C. The Langmuir adsorption model yielded a better fit than the Freundlich adsorption model. The adsorption equilibrium time at 30°C was at 60 min for a HPAM concentration of 500 mg/L, while for a concentration of 1000 mg/L, it was at 90 min. The adsorption equilibrium time at 60°C was 40 min for a HPAM concentration of 500 mg/L, whereas it was 60 min for a HPAM concentration at 1000 mg/L. The pseudo-second order kinetics model yielded better fits than the pseudo-first order kinetics model. The adsorption of HPAM on shale was strong, and the adsorbed HPAM resembled cobwebs adhering to the shale surface. HPAM on the surface of shale after adsorption could resist the desorption capacity of water. However, when the amount of adsorbed HPAM on shale increased significantly, the amount of residual HPAM on the surface of the shale decreased rapidly during desorption in deionized water. The desorption of HPAM on the shale surface followed a modified desorption model. The higher the concentration of HPAM adsorbed on the shale surface was, the easier it was to desorb, the easier it was to be removed from the shale.

Over the past decades, research has escalated on the use of polylactic acid (PLA) as replacement for petroleum-based polymers. This is due to its valuable properties, such as renewability, biodegradability, biocompatibility and good thermomechanical properties. Despite possessing good mechanical properties comparable to conventional petroleum-based polymers, PLA suffers from some shortcomings such as low thermal resistance, heat distortion temperature and rate of crystallization, thus different fillers have been used to overcome these limitations. In the frame work of environmentally friendly processes and products, there has been growing interest on the use of cellulose nanomaterials viz. cellulose nanocrystals (CNC) and nanofibers (CNF) as natural fillers for PLA towards advanced applications other than short-term packaging and biomedical. Cellulosic nanomaterials are renewable in nature, biodegradable, eco-friendless and they possess high strength and stiffness. In the case of eco-friendly processes, various conventional processing techniques, such as melt extrusion, melt-spinning, and compression moulding, have been used to produce PLA composites. This review addresses the critical factors in the manufacturing of PLA-cellulosic nanomaterials by using conventional techniques and recent advances needed to promote and improve the dispersion of the cellulosic nanomaterials. Different aspects, including morphology, mechanical behavior and thermal properties, as well as comparisons of CNC- and CNF reinforced PLA, are also discussed

Weathering and erosion transport minerals and organics toward the sea or lake bottoms over geologic time. The finest solids are deposited in lower, less turbulent areas, such as lake bottoms and continental shelves. They sometimes stack up to thicknesses of kilometers, and begin compacting. These sediment sections are called shales, and as initially deposited in water, shales can have porosities up to 50-80{\%} water, As they are buried, many alteration products from oil to slate are produced due to overburden and temperature increasess, making them important to study. A preceeding paper \cite{1} showed that pressure solution is the primary mechanism for porosity reduction, with possible mechanical compaction at shallow depths. Without naming the mineral(s) involved, it postulated that the greater the product of the water and pore interfaces, the faster the reaction would proceed. This term is $ \varphi^{4m/3}(1-\varphi)^{4n/3}$ , where $\varphi$ is porosity and m and n are numbers close to unity. The large exponents, {\em 4/3}, recognize that the reaction occurs at the molecular scale at which the surfaces are rough. A second term, $\exp^{(-E/RT)}$ , indicates that the reaction is impeded by a quantum energy barrier, E, with diminished impeding power as increased available thermal energy, represented by the absolute temperature, T, becomes available at greater depths in the Earth. These two factors combine to allow porosity $\varphi$ to reduce with time, or equivalently for the fraction of solids, $(1-\varphi)$, to increase with time,$\left. \frac{\partial(ln(1-\varphi) ) }{\partial t } \right |_{\sigma} = (\varphi )^{4m/3}( 1-\varphi )^{4n/3}Ae^{-E/(RT)}$. { \em Here it is shown that this equation can cover quantitatively any actual deposition rates which may have been experienced by the six sections studied, the actual deposition rates being unknown for these cases. Hence a time-depth depositional history for any new shale section, known in detail, would allow determination of the parameters m, n, E and a lumped proportionality constant A. This was accomplished by showing that, for a wide range of depositional rates, r, the range of E for any of the studied sections is small compared to laboratory measurements of quartz solution\cite{2}, 24+-15kJ/mol. Results were obtained over this range of r's using the previously determined m and n, and porosity and temperature profiles. The presently existing porosity profiles necessarily incorporate any overpressure or underpressure conditions that may have existed in the past or currently, as the net difference between overburden and pore pressure is a primary driving force for pressure solution. $SiO_2$ usually comprises 20-50{\%} of shales. In conclusion, pressure solution of quartz can account for vertical compaction of shales quantitatively in the studied examples. Separately, a quasi-eqivalent method for discussing reduced porosities in Macron 2 versus Macron 1 as increased vertical stress, rather than additional horizontal stress, is illustrated. Experiments are suggested to clarify the pressure solution mechanism. The role of horizontal forces is discussed. From a global point of view, shale compaction by pressure solution is a quantified step in the cycling of continental rocks, beginning with rifting.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

The pore-throat radius of shale oil reservoir is extremely small, and it is difficult to accurately obtain the absolute permeability and oil-water two-phase relative permeability of actual oil reservoir through conventional core experiments. However, these parameters are very important for reservoir numerical simulation. In this paper, a method for characterizing flow parameters based on pore network model that considers differential pressure flow and diffusion flow is proposed. Firstly, a digital core was reconstructed using focused ion beam scanning electron microscopy (FIB-SEM) from the Gulong shale reservoir in the Songliao Basin, China, and a pore network model was extracted. Secondly, quasi-static single-phase flow and two-phase flow equations considering diffusion were established in the pore network model. Finally, pore throat parameters, absolute permeability, and oil-water two-phase permeability curves were calculated, respectively. The results show that the pore throat distribution of Gulong shale reservoir is mainly concentrated in the nanometer scale, the mean pore radius is 87 nm, the mean throat radius is 41 nm, and the mean coordination number is 3.97; The calculated permeability considering diffusion is 0.000124mD, which is approximately twice the permeability calculated without considering diffusion; The irreducible water saturation of the Gulong shale reservoir is approximately 0.26, and the residual oil saturation is approximately 0.73. The method proposed in this paper can provide an important approach for characterizing the flow parameters of similar shale oil reservoirs.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P&lt;0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

In-situ injection of steam for heating of the subsurface is an efficient method for the recovery of oil and gas from oil shale where permeability typically evolves with temperature. We reported measurements on Jimusar oil shales(Xinjiang, China) at different temperatures to 600℃ and under recreated in situ triaxial stresses to obtain permeability evolution with temperature and stress. Permeability of tight oil shales evolves with temperature to a threshold temperature and peak temperature. The threshold temperature was subjected to triaxial stresses. For Jimusar oil shale, the threshold temperature ranges from 200℃ to 250℃ at ground stress of buried depth of 500m and from 350℃ to 400℃ at buried depth of 1000m. The peak temperature was almost not subjected to triaxial stress and the range is from 450℃ to 500℃ for all Jimusar samples. Pyrolysis plays an important role in permeability evolution and fundamentally changes permeability tendency and magnitude. At high temperature permeability exhibits a little reduction due to stress effect but still remains a high level due to pyrolysis. The above results show that oil shale mass can change from tight porous media into highly permeable media and oil & gas can easily flow through oil shale stratum.

The Gulong shale oil reservoir is formed in freshwater to slightly saline lacustrine basins, mainly consisting of pure shale geological structure, which is quite different from other shale reservoirs around the world. Currently, the development of Gulong shale oil mainly relies on hydraulic fracturing, while the subsequent shut-in period for imbibition has been proven to be an effective method for enhancing shale oil recovery. To clarify the characteristics of fluid occurrence space and the variation of fluid occurrence during saltwater imbibition in Gulong shale, this paper carried out porosity and permeability tests on Gulong shale cores, and analyzed the fluid occurrence space characteristics and imbibition oil recovery based on nuclear magnetic resonance (NMR). In the porosity and permeability tests, the porosity measured by saturation method was calibrated using NMR T2 spectra. Combined with the identification of fractures in shale cores using micro-CT and the analysis of porosity and permeability parameters, it was found that the permeability of shale cores was related to the development of fractures in shale cores. Through the testing and analysis of NMR T1-T2 two-dimensional spectra of the shale cores before and after saturation with oil, it was found that the shale mainly contains heavy oil, light oil, and clay-bound water, and they were distributed in different positions in the T1-T2 spectrum. Finally, the T1-T2 two-dimensional spectra of the shale core at different imbibition stages were analyzed, and it was found that the saltwater mainly entered the minuscule inorganic pores of clay minerals during the imbibition process, and squeezed the larger-sized inorganic pores containing light oil through the hydration expansion effect, thus expelling the light oil from the shale core and achieving the purpose of enhanced oil recovery.

The oil and gas industry in Nigeria, a vital contributor to the nation's economy, has long been associated with significant environmental challenges. Pollution, habitat destruction, and greenhouse gas emissions have raised global concerns about sustainability and corporate responsibility. This empirical study explores the relationship between environmental accounting practices and the financial performance of listed oil and gas companies in Nigeria. We investigated eight oil and gas companies that are publicly traded on the Nigerian Stock Exchange Market (NGX) as of January 17, 2022, from 2011 to 2022. The study employs Driscoll-Kraay standard errors and reveals that environmental accounting had significant effects on returns on assets, earnings per share, and liquidity ratio. The study revealed that the implementation of environmental accounting practices had diverse effects on the performance of oil and gas companies in Nigeria. The findings encourage policymakers and stakeholders in the sector to utilise the insights and design more effective regulations and incentives that promote environmental corporate responsibility. Also, valuable insights into the potential benefits and challenges associated with adopting environmental accounting practices, and influencing the decision-making processes of corporate stakeholders were provided to ensure sustainability in terms of improved financial performance of the oil and gas sector in Nigeria.

Agriculture (crop production, land use, and livestock) is the second most important greenhouse gas (GHG) emitting sector after the energy sector. Agriculture is also recognized as the source and sink of GHGs. Evidence demonstrates that the application of high amounts of nitrogen-rich fertilizers enhances methane (CH4) and nitrous oxide (N2O) emissions, which are potent GHGs with a high global warming potential (GWP). Considering its global contribution to the climate crisis, reducing GHG emissions in agriculture would considerably lower its share of the global GHG emission records, which may lead to enormous benefits for the environment and food production systems. Several diverging and controversial views questioning the actual role of plants in the current global GHG budget continue to nourish the debate globally. We must acknowledge that considering the beneficial roles of major GHGs to plants at a certain level of accumulation, implementing GHG mitigation measures from agriculture is indeed a complex task. This review seeks to provide key approaches for GHG mitigation in the literature (environmentally friendly crop cultivation and residue management practices, improvement of plants nutrients/fertilizer use efficiency, exploring the genetic diversity for low GHG emission, soil methane-producing bacteria, integrated soil fertility management, improved livestock feeding efficiency, and production, etc.). This work gathers key approaches from 275 peer-reviewed publications, including experimental research papers, review articles, and books, discussing greenhouse gas emissions mechanisms and mitigation to unravel effective strategies for GHG mitigation, proven to be effective or carry the potential to mitigate GHG generation from agriculture. This review also discusses in depth the significance and the dynamics of strategies regarded as game changers with a high potential to enhance, in a sustainable manner, the resilience of agricultural systems. Agricultural GHG mitigation approaches discussed in this work can serve as game changers in global efforts to reducing GHG emissions and alleviating the impact of climate change through sustainable agriculture and informed-decision making.

It’s well known that existing horizontal well drilling and hydraulic fracturing technology that is used to achieve large-scale cost-effective production from immature to low-moderate maturity continental shale in China, where the organic matter mainly exists in the solid form is fairly ineffective. To overcome the obstacles, in-situ conversion technology seems feasible, while implementing it in the target layer along with estimating the amount of expected recoverable hydrocarbon in such shale formations seems difficult. This is because there is no guideline to choose the most appropriate method and select relevant key parameters for this purpose. Hence, based on thermal simulation experiments during the in-situ conversion of crude oil from the Triassic Chang 73 Formation in the Ordos Basin and the Cretaceous Nenjiang Formation in the Songliao Basin, this deficiency in knowledge was addressed. First, relationships between the in-situ converted total organic carbon (TOC) content and the vitrinite reflectance (Ro) of the shales and between the residual oil volume and the hydrocarbon yield was established. Second, the yields of residual oil and in-situ converted hydrocarbon were measured, revealing their sensitivity to fluid pressure and crude oil density. In addition, a model was proposed to estimate the amount of in-situ converted hydrocarbon based on the TOC, hydrocarbon generation potential, Ro, residual oil volume, fluid pressure, and crude oil density. Finally, a method was established to determine key parameters on the final hydrocarbon yield from immature to low-moderate maturity organic material during in-situ conversion in shales. Following the procedure outlined in this paper, estimated recoverable in-situ converted oil in the shales of the Nenjiang Formation in the Songliao Basin was estimated to be approximately 292×108 tons, along with 18.5×1012 cubic meters of natural gas, in an area of approximately 8×104 square kilometers. Collectively, the method developed in this study is independent from the organic matter type and other geological and/or petrophysical properties of the formation and can be applied to other areas globally where there isn’t any available in-situ conversion thermal simulation experimental data.

We replace the current industry-standard empirical forecasts of oil production from hydrofractured horizontal wells in shales with a statistically and physically robust, accurate and precise approach, using the Bakken shale as an illustration. The proposed oil production forecasting method extends our previous work on predicting fieldwide gas production in the Barnett shale and merges it with our new scaling of oil production in shales. We first divide the existing 14,678 horizontal oil wells in the Bakken into 12 static samples in which depositional settings and completion technologies are similar. For each sample, we construct a purely data-driven P50 well prototype by merging the GEV distribution fits of oil production from appropriate well cohorts. We fit the parameters of our physics-based scaling curve to the statistical well prototypes, and obtain their smooth extrapolations to 30 years on production. By calculating the number of potential wells of each Bakken region, and scheduling future drilling programs, we stack up the extended well prototypes to achieve the most plausible forecast. We predict that Bakken will ultimately produce 5 billion barrels of oil from the existing wells, with the possible increments of 2 and 6 billion barrels from core and noncore areas.

This paper concerns the effect of proppant embedment related with hydraulic fracturing treatment. This phenomenon occurs if the strength of the reservoir rock is lower than proppant grains. The aim of the research is laboratory determining the loss of width of the proppant pack built of light ceramic grains. The laboratory simulation of the embedment phenomenon was carried out for a shale rock on a hydraulic press, in a specially prepared for this purpose a heated embedment chamber. Tests were conducted at high temperature and axial compressive stress conditions. The surfaces of the cylindrical core plugs (fracture faces) were imaged under an optical microscope equipped with 3D software. The fracture faces were examined and compared before and after the embedment phenomenon. The analysis of the obtained images of the fracture face were made based on the research method of the embedment phenomenon developed at Oil and Gas Institute-NRI. On the basis of laboratory tests, the parameters characterizing the embedment phenomenon were collected and discussed. In addition, the percentage reduction in the width of the proppant pack was determined.

In order to achieve global climate goals, it is necessary to estimate greenhouse gases (GHG) fluxes from ecosystems. To obtain a comprehensive assessment of CO2, СН4, N2O natural fluxes for the Russian Federation we used the "bottom-up" method according to [1]. We updated estimates for forest ecosystems based on State Forest Inventory data and satellite monitoring of forest disturbances. For grassland ecosystems, it was based on the correct distribution of areas between steppe and non-steppe zones. The estimated net uptake of natural ecosystems of Russia was 1.1 ± 1.8 billion tons of CO2-eq./year. The study shows that if only CO2 is taken into account, the net absorption of terrestrial ecosystems in Russia corresponds to more than -2.5 billion tons of CO2 (35% of forests’ contribution). However, given the emissions of non-CO2 GHGs, total net absorption in Russia’s natural ecosystems is reduced to about -1 billion tons of CO2-eq (with the forests’ contribution increasing to 80%). With regard to anthropogenic fluxes, the overall balance of GHGs in Russia corresponds to net-emissions of 1 billion tons of CO2-eq/year into the atmosphere. To improve reporting under the Paris Agreement, countries should aim to include only anthropogenic ("manageable") GHG fluxes on managed land.

A recent study by the Wall Street Journal reveals that the hydrofractured horizontal wells in shales have been producing less than forecasted by the industry with the empirical hyperbolic decline curve analysis (DCA). As an alternative to DCA, we introduce a simple, fast and accurate method of estimating ultimate recovery (EUR) in oil shales. We adopt a physics-based scaling approach to analyze oil rates and ultimate recovery from 14,888 active horizontal oil wells in the Bakken shale. To predict EUR, we collapse production records from individual horizontal shale oil wells onto two segments of a master curve: (1) We find that cumulative oil production from 4,845 wells is still growing linearly with the square root of time; and (2) 6,401 wells are already in exponential decline after approximately seven years on production. In addition, 2,363 wells have discontinuous production records, because of refracturing or changes in downhole flowing pressure, and are matched with a linear combination of scaling curves superposed in time. The remaining 1,279 new wells with less than 12 months on production have too few production records to allow for robust matches. These wells are scaled with the slopes of other comparable wells in the square-root-of-time flow regime. In the end, we predict that total ultimate recovery from all existing horizontal wells in Bakken will be some 4.5 billion barrels of oil. We also find that wells completed in the Middle Bakken formation, in general, produce more oil than those completed in the Upper Three Forks formation. The newly completed longer wells with larger hydrofractures have higher initial production rates, but they decline faster and have EURs similar to the cheaper old wells. There is little correlation among EUR, lateral length, and the number and size of hydrofractures. Therefore, technology may not help much in boosting production of new wells completed in the poor immature areas along the edges of the Williston Basin. Operators and policy-makers may use our findings to optimize the possible futures of the Bakken shale and other plays. More importantly, petroleum industry may adopt our physics-based method as an alternative to the overly-optimistic hyperbolic DCA that yields an "illusory picture" of shale oil resources.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.

The Fengcheng Formation in the Mahu Sag of the Junggar Basin was generally composed of detritus, pyroclastic material, carbonates, and evaporites. During the process of sedimentation, the climate was arid or semi-arid. Due to the effect of high concentration and sodium-rich source, an alkaline lake was formed, and alkaline minerals were also preserved in the stratum. After the sediments were buried, three mineral assemblages were formed in the Fengcheng Formation, which are carbonate mineral assemblages (i.e., calcite + ferreous dolomite), reedmergnerite and carbonate mineral assemblages (i.e., reedmergnerite + calcite + ferreous dolomite), and reedmergnerite and alkaline mineral assemblages (i.e., reedmergnerite + shortite + trona), respectively. According to the homogenization temperature of reedmergnerite primary fluid inclusions, alkaline diagenesis of Fengcheng Formation is divided into early stage（≤100℃） and middle stage（＞100℃）, respectively. The former is characterized by the generation of ferreous saddle dolomite, quartz dissolution, and agglutination of the laumontite, which occurred under normal burial conditions. The latter is marked by the reedmergnerite’s appearance, which is correlated to deep hydrothermal activity controlled by faults. Finally, based on sedimentary and diagenetic factors, including climate, provenance, diagenetic surroundings, and the action of subsurface fluid, the alkaline deposition-diagenesis model for shale series in four stages of the Fengcheng Formation was established.

With the popularization of natural gas and the requirements for environmental protection, the development and utilization of natural gas is particularly important. The status of natural gas in China's oil and gas exploration and development is constantly improving, and the country is paying more and more attention to the exploitation and utilization of natural gas. The Upper Paleozoic tight sandstone in the Ordos Basin is characterized by low porosity, low permeability and large area of concealed gas reservoirs. By injecting CO2 into the formation, the recovery of natural gas can be improved, and at the same time, the stable storage of CO2 can be achieved to achieve a win-win situation of CO2 emission reduction and utilization. Injecting greenhouse gas CO2 into gas reservoirs for storage and improving recovery has also become a hot research issue. In order to improve the recovery efficiency of tight sandstone gas reservoir, this paper takes the complex tight sandstone of Upper Paleozoic in Ordos Basin as the research object, through indoor physical simulation experiments, carried out the influence of displacement rate, fracture dip angle, core permeability, core dryness and wetness on CO2 gas displacement efficiency and storage efficiency, and analyzed the influence of different factors on CO2 gas displacement efficiency and storage efficiency to improve the recovery and storage efficiency. The research results show that under different conditions, when the CO2 injection pore volume is less than 1PV, the relationship between the CH4 recovery rate and the CO2 injection pore volume is linear, and the tilt angle is 45 °. When the CO2 injection pore volume exceeds 1PV, the CH4 recovery rate increases slightly with the increase of displacement speed, the recovery rate of CO2 displacement CH4 is between 87% - 97%, and the CO2 breakthrough time is 0.7PV-0.9PV. In low-permeability and low-speed displacement cores, the diffusion of CO2 molecules is more significant. The lower the displacement speed is, the earlier the breakthrough time of CO2 is, and the final recovery of CH4 slightly decreases. Gravity has a great impact on CO2 storage and enhanced recovery. The breakthrough of high injection and low recovery of CO2 is earlier, and the recovery of CH4 is about 3.3% lower than that of low injection and high recovery. The bound water makes the displacement phase CO2 partially dissolved in the formation water, and the CO2 breakthrough lags about 0.1PV. Ultimately, CH4 recovery factor and CO2 storage rate are higher than those of dry core displacement. The research results provide theoretical data support for CO2 injection to improve recovery and storage efficiency in complex tight sandstone gas reservoirs.

Recent studies have reported shallow and deep seep areas offshore Mocha island. Gas hydrate occurrences along the Chilean margin could explain seeps presence. Gas phases (gas hydrate and free gas) and geothermal gradients were estimated analysing two seismic sections. Close to Mocha island (up to 20 km) were detected high (up to 1900 m/s) and low (1260 m/s) velocities associated with high gas hydrate (up to 20 % of total volume) and free gas (up to 1.1% of total volume) concentrations respectively. These values are in agreement with a variable and high geothermal gradient (65 to 110 °C/km) related to high supply deep fluids canalised by faults and fractures. Faraway from Mocha island (more than 60 km), free gas concentrations decrease to 0.3 % of total volume and low geothermal gradient (from 35 to 60 °C/km) are associated with low fluids supply. Finally, we propose gas hydrate dissociation processes as the main supply source for seeps in the vicinity of Mocha island. These processes can be triggered by ancient sliding reported in literature.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

This paper describes a novel concept of producing energy efficient ”Maroon enriched natural gas “ and then Pink hydrogen” from any hydrocarbon base. The key idea is the extraction of hydrogen from water in addition to that from the hydrocarbon in an optimal fashion. This has the benefit of higher water vapor to CO2 exhaust ratio than conventional carbonaceous fuels when generating energy via combustion, a prudent step in achieving Netzero goals in a shorter time, and creating energy independence in most places.. The process of production makes concentrated CO₂ available for use and or sequestration. The process also maximizes use of renewable electricity in hydrogen generation, and maximizes use of existing infrastructure, with a minimum capital cost by energy recycle in the process. The process design applies sound thermodynamic principles which evolved during the nineteenth century, and mimics the geochemical processes going on in some of the natural 'colorless hydrogen'.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

(1) The article is devoted to the development of a theoretical and algorithmic basis for numerical modeling of the spontaneous potential method (SP) as applied to the study of sandy-argillaceous reservoirs. (2) In terms of coupled flows, we consider a physical-mathematical model of SP signals from an electrochemical source, with regard to the case of fluid-saturated shaly sandstone. (3) An algorithm for 2D finite-element modeling of SP signals was developed and implemented in software, along with its internal and external testing with analytical solutions. The numerical SP modeling was carried out, with determining the dependences on the reservoir thickness and porosity, the amount of argillaceous material and the type of minerals. We performed a comparative analysis of the simulated and field SP data, using the results of laboratory core examinations taken from wells in a number of fields in the Latitudinal Ob Region of Western Siberia. (4) The results of the study may be used either for the development of the existing SP techniques, by providing them with a consistent computational model, or for the design of new experimental approaches.

Shales are well known for their strong anisotrophic properties. The classical Athy’s model on the exponential porosity reduction with the depth commonly uses based on localities only. Shale compaction curve affects the results of the basin modeling as it is important input data, thus the standard compaction curve of shales needs to be established. This study provided a new data and complies available data of Thailand shales to propose the new empirical relationship among porosity, burial depth, and geological age. The numerical data of the geological time were estimated by the application from the relationship of velocity and depth in each geological ages. The variation of the Thailand shale data due to the different geological ages was found in this study. Finally, the standard curve of shale compaction proposed by Puttiwongrak et al. [9] was examined and confirmed by this research findings.

The microscopic pore structure of tight sandstone reservoir significantly influences the characteris-tics of CO2 flooding after water flooding. The research was conducted using various techniques such as casting thin sections, high pressure mercury injection, scanning electron microscopy, Nu-clear magnetic resonance (NMR) testing, and a self-designed high-temperatures and high-pressures microscopic visualization displacement system. Three type cores with different pore structures were selected for the flooding experiments and the microscopic visualization displace-ment experiments, including CO2 immiscible flooding, near-miscible flooding, and miscible flood-ing after the conventional water flooding. The characteristics of CO2 flooding and the residual oil distribution after water flooding were quantitatively analyzed and evaluated. The results show that: (1) During the water flooding process, the oil produced from type I and type III samples mainly comes from large and some medium pores. Oil utilization of all pores is significant for type II samples. The physical properties and pore types have a greater impact on water flooding. Type I and II samples are more suitable for near-miscible flooding after water flooding. Type III samples are more suitable for miscible flooding after water flooding. (2) In the CO2 flooding, oil recovery increases gradually with increasing pressure for all three types of samples. Type II core samples have the highest recovery. Before miscibility, the oil recovered from type I and type II samples was primarily from large pores, however, the oil recovery mainly comes from medium pores when reaching miscibility. As for the type III samples, the oil produced in the immiscible state mainly comes from large and medium pores, and the enhanced oil recovery mainly comes from medium and small pores after reaching the near-miscible phase. (3) It can be seen from the microscopic re-sidual oil distribution that oil recovery will increase as the petrophysical properties of the rock model improve. The oil recovery of near-miscible flooding after water flooding regarding the type II model is up to 68.11%. The oil recovery of miscible flooding after water flooding about type III model is the highest at 74.57%. With increasing pressure, the proportion of flake residual oil grad-ually decreases, while the proportion of droplet-like and film-like residual oil gradually increases. Type II samples have a relatively large percentage of reticulated residual oil in the near-miscible stage.

In the article we present the results concerning the impact of structural and chemical properties of zinc oxide in various morphological forms, on its gas-sensitive properties tested in an atmosphere containing a very aggressive gas such as chlorine. Two types of ZnO sensor layers obtained by two different technological methods were used. Their morphology, crystal structure, specific surface area, porosity, surface chemistry and structural defects were characterized, and then compared with gas-sensitive properties in a chlorine-containing atmosphere. To achieve this goal scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL) methods were used. The sensing properties of obtained active layers were tested by temperature stimulated conductance method (TSC). We have noticed that their response in chlorine atmosphere is not determined by the size of the specific surface or porosity. The obtained results showed that the structural defects of ZnO crystals play the most important role in chlorine detection. We demonstrated that the Cl2 adsorption is a concurrent process to oxygen adsorption. Both of them occur on the same active species (oxygen vacancies). They concentration is higher on the side planes of the zinc oxide crystal than the others. Thanks to the conducted studies authors demonstrated that to develop a new gas sensor devices not only changing of active layer chemical composition but also controlling its crystal structure and morphology could be used.

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, the molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopores imbibition during shut-in for a typical shale reservoir Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between “interfacial water molecules” at the imbibition front and “adsorbed oil molecules” on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil especially the heavy hydrocarbon component in the adsorbed layer tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore's wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for “interfacial water molecules” to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect of pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for EOR.

Natural gas is an important energy source among various fossil fuels. However, natural gas typically contains a significant amount of water vapor, which can pose challenges in its usage. Therefore, the process of removing water vapor from natural gas, known as gas dehydration, is crucial in the gas industry. The presence of water vapor in the gas supply can lead to the formation of hydrates, which can cause issues such as blockages in pipelines. To tackle this problem effectively, gas dehydration makes use of Tri ethylene glycol (TEG) as a drying agent. TEG works by selectively absorbing water vapor from the natural gas flow, thereby significantly reducing its moisture content.In the gas dehydration process, wet gas is treated by using lean glycol in an absorber, where the water vapor is removed. The resulting rich glycol is then recovered and recycled for further use. In this study, we explore the possibility of replacing nitrogen with dry natural gas in the re-generator of the glycol dehydration system. The aim is to evaluate the feasibility and effectiveness of this alternative approach. To assess the performance of both techniques, we employed HYSYS modeling and simulation. Through this analysis, we compared the capital and utility expenses associated with each method while ensuring that the glycol purity requirements remained unchanged. By examining the results obtained from the simulations, we can gain insights into the economic viability and efficiency of utilizing dry natural gas in the re-generator stage of the glycol dehydration process.In addition to the primary purpose of removing water vapor, the wet gas obtained from the stripping mechanisms in the glycol dehydration process can serve additional functions. It can be utilized to power steam pumps and compressors, thereby maximizing energy efficiency within the system. Alternatively, the wet gas can be recycled back into the process for further treatment. To develop a comprehensive understanding of the entire mechanism, we constructed a model based on the actual flow diagram. This model takes into account the various components and processes involved in the glycol dehydration system, including the stripping mechanisms and their connection to other equipment. By analyzing the data and outcomes generated by this model, we can derive valuable insights. These findings can be utilized to optimize the heat and material balance within the plant, ensuring efficient operation and potentially leading to the design of an improved system in terms of energy consumption and overall performance

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

The available direct gas dynamic tables provide the area ratio and the Prandtl-Meyer(P-M) angle of isentropic expansion of gas as functions of the Mach number. But finding the value of the Mach number in terms of area ratio or P-M angle requires an inverse function. Currently, the Mach number is determined by either interpolation from the direct gas dynamics tables, or the application of non-linear equation solvers using numerical methods. Both methods are approximate. In this paper inverse functions for Mach number in the form of Taylor’s series expansions are reported to develop the so-called inverse tables. The advantage of this approach is that the Mach number with a greater accuracy, referred to as nearly exact can be obtained by reading from the inverse table. In the presentation, the necessary equations and new tables that can be used by the scientific community will be disseminated. The data and computer programs are made available on GitHub through https://github.com/anillals/Inverse-gas-dynamic-tables- and-codes. A paper describing the complete mathematical steps in the derivation of the equations can be found at https://rdcu.be/dgrlf

Multi-stage hydraulic fracturing with horizontal well technology has been widely used in shale oil reservoir. After hydraulic fracturing, hydraulic fractures and opened beddings are intertwined, which result in a complex fracture network. As well as the migration of multi-phase fluids during fracturing and soaking processes, which lead to complex flowback performance, and brings dif-ficulty to productivity evaluation and flowback strategies optimization. In this paper, taking the Daqing Gulong shale reservoir as an example, a numerical model for flowback period, which considered oil-water-gas three-phase flow and orthogonal fracture network has been established. The characteristics and influencing factors of flowback performance have been deeply studied, and the flowback modes of shale oil are reasonably optimized. Factors such as PTPG (pseu-do-threshold pressure gradient), opened bedding stress sensitivity, opened bedding permeability and matrix permeability have obvious effects on the flowback performance, resulting in signifi-cant variations in production peaks, high yield periods, and decline rates. In addition, three flowback modes are distinguished based on the rate at which the BHP (bottom hole pressure) drops. These correspond to three types of choke modes. Based on the result of numerical model, three flowback modes are optimized and the impacts of different flowback modes on shale oil flowback are clarified. This study is particularly important for understanding the performance of shale oil flowback and guiding the efficient exploitation of shale oil.

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

A growing number of companies in the brewery industry have made commitments to measure and reduce their greenhouse gas (GHG) emissions. However, many brewers, particularly craft brewers with relatively low rates of production, have struggled to meet these commitments. The purpose of this research was to investigate the challenges and benefits of measuring and reducing GHG emissions in the craft brewery industry. The research was conducted in Ontario, Canada, which has seen strong recent growth in the craft brewery industry. A case study and semi-structured interviews among Ontario Craft Brewers were conducted. The case study found that indirect (scope 3 emissions under the WBCSD & WRI GHG Protocol) GHG sources accounted for 46.4% of total GHGs, with major sources from barley agriculture, malted barley transportation, and bottle production. Direct emissions (scope 1) accounted for only 14.9% of GHGs, while scope 2 emissions, comprised mainly of energy consumption, accounted for 38.7% of GHGs. The case study and interviews found that the main challenges in calculating brewery GHGs are secondary data availability, technical knowledge, and finances. The study also found that the main benefits for Ontario breweries to measure their GHGs include sustainability marketing and preserving the environment. The interviews also found a poor understanding of carbon regulation among Ontario Craft Brewers, which is interesting considering that Ontario implemented a provincial cap and trade program in 2017.

Gas hydrate provinces are present in at least in two areas along Brazil’s continental margin: (1) the Rio Grande Cone in the southeast, and (2) the Amazon deep-sea fan in the equatorial region. The occurrence of gas hydrates in these depocentres was first detected geophysically and has recently been proven by seafloor sampling of gas vents, detected as water column acoustic anomalies rising from seafloor depressions (pockmarks) and/or mounds, many associated with seafloor faults. The gas vents include typical features of cold seep systems, including shallow sulphate reduction depths (<4 m), authigenic carbonate pavements and chemosynthetic ecosystems. In both areas, gas sampled in hydrate and in sediments is dominantly formed by biogenic methane. Calculation of the methane hydrate stability zone for water temperatures in the two areas shows that gas vents occur along its feather edge (water depths between 510-760 m in the Rio Grande Cone and 500-670 m in the Amazon deep-sea fan) but also in deeper waters within the stability zone. Gas venting along the feather edge of the stability zone could reflect gas hydrate dissociation and release to the oceans, as inferred on other continental margins, or upward fluid flow through the stability zone facilitated by tectonic structures recording the gravitational collapse of both depocentres. The potential quantity of venting gas on the Brazilian margin under different scenarios of natural or anthropogenic change require further investigation. The studied areas provide a natural laboratory where these critical processes can be analysed and quantified.

The planned closure of potash mines, achieved through the injection of highly mineralized brines into the worked-out area, is a complex and not fully studied process. A critical concern arises when brines obstruct the aerodynamic connections between the flooded mine's airspace and the atmosphere, potentially leading to the formation of closed cavities where explosive gases can accumulate. To address this hazard, it is imperative to develop systems capable of extracting the gas-air mixture from the unflooded domed portions of the worked-out area. This is the focus of this study, in which we analyze gas-dynamic processes within the potassium mine worked-out area during planned flooding. Two distinct scenarios are examined: the first involves controlled flooding with saturated brines, while the second contemplates flooding resulting from a hypothetical breakthrough of supra-salt strata, leading to the ingress of groundwater into the worked-out area. A novel mathematical model is introduced to predict the evolution of gas-air mixture parameters in the unflooded dome segment of the worked-out area. Utilizing this model, we assess the effectiveness of proposed measures designed to eliminate explosive gases from the worked-out area. Specifically, a pipeline system is proposed for the removal of gases, followed by their dilution below the maximum permissible concentrations in the effluent jet. The findings from this study contribute valuable insights into ensuring the safe and efficient closure of potash mines, shedding light on potential risks and effective mitigation strategies for gas-related hazards during planned flooding.

Neuronal PAS domain protein 2 (NPAS2) is a hemeprotein comprising a basic helix-loop-helix domain (bHLH) and two heme-binding sites, the PAS-A and PAS-B domains. This protein acts as a pyridine nucleotide-dependent and gas-responsive CO-dependent transcription factor and is encoded by a gene whose expression fluctuates with circadian rhythmicity. NPAS2 can heterodimerize with ARNTL in the activating limb of the transcriptional/translational feedback loop operating the circadian clock circuitry. NPAS2 can functionally substitute for the core transcription factor and histone/protein acetylase CLOCK in the molecular clockwork endowing central oscillators in the suprachiasmatic nuclei of hypothalamus as well as in peripheral oscillators in the cell of other body tissues, such as the liver and kidney.

The novel Ionized Gas Thermoelectric Generator (IG-TEG) system that has been studied theoretically showing capabilities to continually extracting energy from the thermal energy of the ambient air, at low temperatures within the standard room temperature and below. This system does not need a temperature gradient in order to work, unlike the other TEGs that use Seebeck effect, and therefore this new system can be utilized for cooling purposes, by extracting energy instead of wasting energy in compressing the gas for cooling. This novel system was designed based on Static Ratchet Potential (SRP), which is known as a spatially asymmetric electric potential produced by an array of positive and negative electrodes. The ratchet potential produces electrical current from random Brownian Motion of charged particles that are driven by thermal energy. Ratchet potential was studied and investigated by several researches in the fields of sensing and energy harvesting. The main ratchet potential system parameter is the particles transportation, this parameter was studied under the condition of flashing ratchet potentials, and was analyzed based on several methods. In this study, a different approach is pursued to estimate particles transportation, by evaluating the charged particles distribution, and applying the other conditions of the SRP.

The western Sulige gas field is a new and key reserve area for the rolling development of the Sulige gas field in China. However, due to the complex gas–water relationship and the difficulty in identifying gas and water formation, the scale and benefit deployment of the gas field are seriously restricted. In particular, almost all of the wells in the area produce water and no water measurement has been carried out for any single well, which leads to an unclear understanding of the dynamic characteristics of the production wells, thus affecting the productivity calculations of the gas wells and the overall regional productivity evaluation. Based on the testing data for a gas well, the impacts of the reservoir property parameters on the gas and water production were analyzed by combining the production performance and static geological characteristics. It was determined that the physical parameters K, Kh, and φSg had good positive correlations with gas production but not with water production; thus, effective prediction cannot be obtained for water production in gas well testing. After the analysis of the liquid loading law, the gas wells were classified into three types: continuous liquid carrying production, slight liquid loading, and liquid loading wells. In general, up to 96% of the gas wells were liquid loaded. According to the different production performances exhibited in the different stages of the gas wells, five types of methods for diagnosing water production wells were proposed (gas testing, pilot production, gas–liquid two-phase measurement testing, liquid level detection, and production performance analysis), as well as the diagnostic criteria and corresponding solutions. To obtain real-time water production data for each well and investigate the change of water-gas ratio (WGR) during the whole production process, a water production splitting method for gas wells based on three-dimensional geological modeling and numerical simulation combined with the constraints of the total water production of gas gathering stations was explored and established. The splitting results can be used to evaluate the water and gas productivity of gas wells and determine the best deliquification period. The gas well productivity when water production was considered was about 10% lower than that when water production was not considered. The best deliquification period was determined to be 125 days for wells with small water production, 20 days for wells with moderate water production, and 3 days for wells with serious water production. The results of this study could provide technical support for the scientific evaluation of gas well production indicators, reduction of development costs, and improvement of oil recovery.

This paper addresses the atmospheric emissions from oil and gas extraction and production in Greece. The study was carried out in 2014 in the Kavala gulf, which currently is the only location of oil and gas production in Greece and where the exploration activities for hydrocarbons started in the late ‘60’s. This study presents the qualitative and quantitative characteristics of atmospheric emissions, in relation also to the emissions’ control management system. Particular reference is made to sulphur compounds since the existence of volcanic rocks results to increased amounts of H₂S. The results shows that, currently, atmospheric emissions of pollutants during extraction and production of hydrocarbons in Greece are very low and do not have any significant effect on air quality and climate change. Since it is expected that exploitation of hydrocarbons and oil and gas extraction and production will increase in the future, appropriate measures should be taken to ensure environmental protection, such as the development of integrated monitoring systems and the use of up to date emission control technologies.

Diving decompression theory hypothesizes inflammatory processes as a source of micronuclei which could increase related risks. Therefore, we tested 10 healthy, male divers. They performed 6-8 dives with a maximum of two dives per day at depths ranging from 21 to 122 msw with CCR mixed gas diving. Post-dive VGE were counted by echocardiography. Saliva and urine samples were taken before and after each dive to evaluate to evaluate inflammation: ROS production, lipid peroxidation (8-iso-PGF2), DNA damage (8-OH-dG), cytokines (TNF-, IL-6, and neopterin). VGE exhibits a progressive reduction followed by an increase (p<0.0001) which parallels in-flammation responses. Indeed, ROS, 8-iso-PGF2, IL-6 and neopterin increases from 0.19 ± 0.02 to 1.13 ± 0.09 μmol.min−1 (p<0.001); 199.8 ± 55.9 to 632.7 ± 73.3 ng.mg-1 creatinine (p<0.0001); 2.35 ± 0.54 to 19.5 ± 2.96 pg.ml-1 (p<0.001); and 93.7 ± 11.2 to 299 ± 25.9 μmol·mol−1 creatinine (p=0.005), respectively. The variation after each dive was held constant around 158.3 ± 6.9% (p = 0.021); 151.4 ± 5.7% (p <0.0001); 176.3 ± 11.9% (p<0.0001); and 160.1 ± 5.6% (p<0.001), respectively. When oxy-inflammation reaches a certain level, it exceeds hormetic coping mechanisms allowing second-generation micronuclei substantiated by an increase of VGE after an initial continuous decrease consistent with a depletion of “first generation” pre-existing micronuclei.

Membranes are a selective barrier that allows certain species (molecules and ions) to pass through while blocking others. Some rely on size exclusion, where larger molecules get stuck while smaller ones permeate through. Others use differences in charge or polarity to attract and repel specific species. Membranes can be used to purify air and water by allowing only air and water molecules to pass through but preventing contaminants such as microorganisms and particles or to separate target gas or vapor, such as H2, CO₂, from other gases. The higher the flux and selectivity, the better a material is for membranes. The desirable performance can be tuned through material type (polymers, ceramics, and biobased materials), microstructure (porosity and tortuosity), and surface chemistry. Most membranes are made from plastic from petroleum-based resources, which contribute to global climate change and plastic pollution. Cellulose can be an alternative sustainable resource to make renewable membranes. Cellulose exists in plant cell walls as natural fibers, which can be broken down into smaller components such as cellulose fibrils, nanofibrils, nanocrystals, and cellulose macromolecules through mechanical and chemical processing. Membranes made from reassembling these particles and molecules have variable pore architecture, porosity, and separation properties and therefore have a wide range of applications in nano-, micro-, and ultrafiltration or forward osmosis. Despite their advantages, cellulose membranes face some challenges. Improving the selectivity of membranes for specific molecules often comes at the expense of permeability. The stability of cellulose membranes in harsh environments or under continuous operation needs further improvement. Research is ongoing to address these challenges and develop advanced cellulose membranes with enhanced performance. This article reviews the microstructure, fabrication methods, and potential applications of cellulose membranes, providing some critical insights into processing-structure-property relationships for current state-of-the-art cellulosic membranes that could be used to rationally improve their performance.

Enhancing the management and monitoring of oil and gas processes demands developing precise predictive analytics techniques. Over the past two years, oil and its prediction have advanced significantly using conventional and modern Machine Learning techniques. Several review articles detail the developments in predictive maintenance and technical and non-technical aspects of influencing the uptake of big data. The absence of references for machine learning techniques impacts the effective optimization of predictive analytics in the oil and gas sector. This review paper offers readers thorough information on the latest machine learning methods utilized in this industry's predictive analytical modelling. The review covers forms of Machine Learning techniques used in predictive analytic modelling from 2021 to 2023 (91 articles). It provides an overview of the details of the papers that were reviewed, comprising of the model’s categories, the data's temporality, field, and name, the dataset's type, predictive analytics (classification or clustering or prediction), the models' input and output parameters, performance metrics, optimal model, and benefits and its drawbacks. Additionally, suggestions for future research directions are provided to raise the potential of the associated knowledge and increase the accuracy of oil and gas predictive analytics models.

India, the world’s most populous country, is the world's third-largest emitter of greenhouse gases (GHGs). Despite employing several energy sources, it still relies heavily on coal, its primary energy source. Given India’s swiftly rising energy demand, this challenges meeting emission reduction targets. India has significantly increased investments in renewables like solar and hydrogen in recent years. While commendable, these initiatives alone cannot meet the country's expanding energy demands. In the short term, India must rely on both domestic and imported fossil fuels, with natural gas being the most environmentally friendly option. In this context, this paper attempts to forecast energy consumption, natural gas production, and consumption in India till 2050 using both univariate and multivariate forecasting methods. For multivariate forecasting, we have assumed two alternative possibilities for GDP growth: the business-as-usual and the high-growth scenarios. Each of our forecasts indicates a notable shortfall in the projected production of natural gas compared to the expected demand, implying our results are robust. Our model predicts that nearly 30-50 percent of India’s natural gas consumption will be met by imports, mainly in the form of LNG. Based on these findings, this paper recommends that Indian government policies emphasize increasing domestic natural gas production, importing LNG, and expanding renewable energy resources.

Gas turbine engines are widely used in various industries such as aviation, power generation, and marine propulsion due to their high efficiency and reliability. The combustion chamber of a gas turbine engine design contains a number of elements, including as the chamber's size and form, the fuel injection system, the ignition system, and the cooling system and it plays a critical role in the performance and efficiency of the engine. This research discusses the fabrication of a combustion chamber model for a gas turbine engine. The aim of this research is to develop a combustion chamber that is cost-effective, easily available, and can be fabricated in less time. The research covers the different types of combustion chambers used in gas turbine engines and compares their advantages and disadvantages. It then selects the best type of combustion chamber for the gas turbine engine based on its cost, availability, and fabrication time, Efficiency and high power to fuel ratio. The report also describes the fabrication process involved, including the techniques and materials used, along with safety precautions and environmental protection measures. Lastly, the research suggests future improvements and potential applications for the fabricated combustion chamber model.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Gas flaring is a disposal process widely used in the oil extraction and processing industry. It consists in the burning of unwanted gas at the tip of a stack and due to its thermal characteristic and the thermal emission it is possible to observe and to quantify it from space. Spaceborne observations allows us to collect information across regions and hence to provide a base for estimation of emissions on global scale. We have successfully adapted the Visible Infrared Imaging Radiometer Suite (VIIRS) Nightfire algorithm for the detection and characterisation of persistent hot spots, including gas flares, to the Sea and Land Surface Temperature Radiometer (SLSTR) observations on-board the Sentinel- satellites. A hot event at temperatures typical of a gas flare will produce a local maximum in the night-time readings of the shortwave and mid-infrared (SWIR and MIR) channels of SLSTR. The SWIR band centered at 1.61 mmis closest to the expected spectral radiancemaximumand serves as the primary detection band. The hot source is characterised in terms of temperature and area by fitting the sum of two Planck curves, one for the hot source and another for the background, to the radiances from all the available SWIR, MIR and thermal infra-red channels of SLSTR. The flaring radiative power is calculated from the gas flare temperature and area. Our algorithm differs from the original VIIRS Nightfire algorithm in three key aspects: (1) It uses a granule-based contextual thresholding to detect hot pixels, being independent of the number of hot sources present and their intensity. (2) It analyses entire clusters of hot source detections instead of individual pixels. This is arguably a more comprehensive use of the available information. (3) The co-registration errors between hot source clusters in the different spectral bands are calculated and corrected. This also contributes to the SLSTR instrument validation. Cross-comparisons of the new gas flare characterisation with temporally close observations by the higher resolution German FireBIRD TET-1 small satellite and with the Nightfire product based on VIIRS on-board the Suomi-NPP satellite show general agreement for an individual flaring site in Siberia and for several flaring regions around the world. Small systematic differences to VIIRS Nightfire are nevertheless apparent. Based on the hot spot characterisation, gas flares can be identified and flared gas volumes and pollutant emissions can be calculated with previously published methods.

AIUS (Atmospheric Infrared Ultraspectral Sounder) is an infrared occultation spectrometer onboard the Chinese GaoFen-5 satellite, which covers a spectral range of 2.4–13.3 μm (750–4100 cm⁻¹) with a spectral resolution of about 0.02 cm⁻¹. AIUS is designed to measure and study chemical processes of ozone (O₃) and other trace gases in the upper troposphere and stratosphere around Antarctic. In this study, the corresponding retrieval methodology is described. The retrieval simulations based on the simulated spectra of AIUS have been carried out, with a focus on O₃. The relative difference between the retrieved and the true O₃ profiles is within 5% from the 15 km to 70 km and about 10% below 15 km. The corresponding averaging kernels illustrate that the overall retrieval information mainly come from the spectra, not the a priori. The retrieval experiments also demonstrate that the shape of the retrieved profiles resembles the shape of the true profile even if the shape of the a priori profile is different from that of the true profile. Further, we perform the O₃ retrieval from the real ACE-FTS (Atmospheric Chemistry Experiment-Fourier Transform Spectrometer) measurements and compare the results with the official ACE-FTS Level-2 products. Overall, both profiles agree well in the stratosphere where the retrieval sensitivity is high. The relative difference between both profiles is about 15% below 70 km, which may due to the measurement errors and different forward model parameters.

The presence of high concentrations of flammable gases and volatile organic compounds in the atmosphere has been widely reported to be detrimental to human survival. A lot of research effort has been put towards finding an efficient means of quick detection of these gases below their ‘immediately dangerous to life or health’ concentrations. Detecting these gases in an oxygen-deficient environment is a crucial task to consider and has been overlooked. In this research, double substitution spinel with chemical formula Co1-2xNixMnxFe2-yCeyO4, where 0 ≤ x = y ≤ 0.3, were prepared via the glycol-thermal technique. The final products following the appropriate substitution are CoFe2O4 (dried naturally), CoFe2O4 (dried with Infrared lamp), Co0.8Ni0.1Mn0.1Fe1.9Ce0.1O4, Co0.6Ni0.2Mn0.2Fe1.8Ce0.2O4, and Co0.4Ni0.3Mn0.3Fe1.7Ce0.3O4 spinel ferrites. The X-ray diffractometry (XRD), High resolution transmission electron micrographs (HRTEM), and X-ray photoelectron spectroscopy (XPS) of the samples confirm the formation of the spinel. The gas sensing performance of this samples were tested at operating temperature of 225 ºC towards liquefied petroleum gas (LPG), ammonia, ethanol, and propanol. The Co0.8Ni0.1Mn0.1Fe1.9Ce0.1O4-based sensor was selective to LPG, with a high response of 116.43 toward 6 000 ppm of LPG when helium was used as carrier gas, 3.35 when dry-air was the carrier gas, 4.4 when nitrogen was the carrier gas, but was not sensitive when argon was used as a carrier gas.

The present study focuses on the development and optimization of a highly efficient unique hybrid technique — membrane-assisted gas absorption (MAGA) in designing the separation unit, which provides the improvement in mass-transfer of a target component during the natural gas processing in terms of sweetening stage. A novel design of membrane-assisted gas absorption cell is used to enhance the ratio between absorbent amount and membrane surface available for permeation. The performance tests were implemented on example of two gas mixtures separation: one is model ternary gas mixture and the second is quasi real natural gas, which includes number of hydrocarbons, nitrogen, acid impurities and xenon. For both cases, the MAGA unit demonstrated high acid gases removal efficiency, and high recovery of hydrocarbons. The ultimate efficiency of studied system was up to 96 and 61 % of removed acid gases with hydrocarbons losses up to 1 % at highest productivity. In this way, the residual sum of acid gases content may be lowered to 1 vol.% using the heat-free hybrid membrane-assisted gas absorption unit maintaining suitable recovery rate of methane, ethane, propane and n-butane. Nevertheless, the overall efficiency of the process may be enhanced using the specific absorption agents with aqueous amino alcohol solutions.

Accent is on determination of appropriate friction factor of the pipes and on selection of the representative equation for water or natural gas flow which is valuable for existing conditions in the looped network of pipelines. Note that in a municipal gas pipeline, natural gas can be treated as incompressible fluid (liquid) i.e. as water or oil. Even under this circumstance, calculation of water pipelines cannot be literary copied and applied for calculation of gas pipelines. Inappropriate friction factor, equally as e.g. inappropriate usage of water flow equations for calculation of gas networks can lead to inaccurate final results. Few iterative methods for determining the optimal hydraulic solution of water- and gas- looped pipeline networks, such as, Hardy Cross, modified Hardy Cross, node-loop method, node and M.M. Andrijashev method, will be shown. Speed of convergence will be compared and discussed using a simple network with three loops.

Risk management for technological hazards mainly focuses on the consequences on human lives. Although technological risk analysis evaluates environmental vulnerability, it does not reflect the consequences on environmentally exposed elements, such as rivers, water springs, flora, and fauna. This paper's objective was to propose a conceptual framework and create a multidisciplinary evaluation model for environmental risk analysis in the oil and gas industry. Initially, the problem was approached from a global perspective to justify the necessity of a holistic environmental risk analysis methodology in the oil industry, using environmental risk factors as well as underlying factors, such as environmental fragility and lack of resilience. The holistic assessment was carried out based on probabilistic risk analysis methodologies to obtain a holistic environmental risk index, HERI. This methodology was applied to an oil and gas industry company in Colombia. This allowed greater disaggregation of the results to establish priorities for risk reduction actions and identify the company's weaknesses.

To meet the International Maritime Organization’s requirements for carbon dioxide emissions from ships, a cost-effective and practical ship decarbonization tower was autonomously designed based on the marine diesel engine model 6135G128ZCa. The tower is internally filled with structured packing, and a slot-type liquid distributor at the top of the packing evenly distributes the NaOH solution to absorb carbon dioxide from the ship’s exhaust gas. Experimental research was conducted to investigate the influence of factors such as liquid-to-gas ratio and NaOH concentration on the performance of the decarbonization tower. The results confirmed that the use of NaOH solution can effectively absorb CO2 from ship exhaust gas, reducing CO2 emissions by more than 81.59% and meeting the EEDI (Energy Efficiency Design Index) requirements specified by the IMO.

Experimental systems to simulate future elevated CO2 conditions in the field often have large, rapid fluctuations in CO2. To examine possible impacts of such fluctuations on photosynthesis, intact leaves of field grown plants of five species were exposed to two-minute cycles of CO2 between 400 and 800 mol mol-1 lasting a total of 10 minutes, with photosynthesis, stomatal conductance and PSII fluorescence measured at the end of each half-cycle, and also 10 minutes after the end of the cycling. Prior to the cyclic CO2 treatments, steady-state responses of leaf gas exchange and fluorescence to CO2 were determined. In four of the five species, in which stomatal conductance decreased with increasing CO2, the cyclic CO2 treatments reduced stomatal conductance. In those species, both photosynthesis and the photochemical efficiency of PSII were reduced at limiting internal CO2 levels, but not at saturating CO2. In the fifth species, there was no change in stomatal conductance with CO2, and no change in either photosynthesis or PSII efficiency at any CO2 level with CO2 cycling. It is concluded that in many, but not all, species fluctuations in CO2 may reduce photosynthesis at low CO2 partly by decreasing the photochemical efficiency of photosystem II, as well as by decreasing stomatal conductance.

Agricultural intensification is considered essential for meeting growing demand for food and biomass for energy and material purposes. Intensifying grasslands is a so-far under-represented although promising option, given their large land area and relatively low management levels. This study quantifies the bioenergy potential from intensifying temporary grasslands in Europe and the integral greenhouse gas emission effects in 2030. We first conduct a literature review of intensification options for European grasslands and then apply the environmental impact assessment model MITERRA-Europe to implement the key intensification option of using multi-species grass mixtures. The results show that 853 kha (or 8%) of temporary grassland could be made sustainably available for additional biomass production. This can be translated into a bioethanol potential of 23 PJ/yr and an emission mitigation potential of 5.8 Mt CO2-eq/yr (if conventional grass mixture from surplus temporary grassland is used for energy) or 72 PJ/yr and 4.0 Mt CO2-eq/yr (if surplus temporary grassland is used for grassy energy crops). Although the bioenergy potential is limited, the intensification measure’s key advantage is that it results in a better environmental performance of temporary grasslands. This makes it a key option for sustainably producing bioenergy in areas with high shares of temporary grasslands.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

Due to poor ventilation conditions in the tunnel, if gas pipeline leaks, the consequence of the accident will be more serious. Therefore, before the emergency repair, gas in the tunnel needs to be excharged so as not to explode during the repair process. Therefore, it is necessary to study the ventilation of gas in the tunnel. Based on the computational fluid dynamics (CFD) theory and taking the Yanyingshan tunnel section of China-Myanmar pipeline as an example, this paper uses Fluent software to establish the leakage model of the gas pipeline and fan model in the tunnel and analyzes the influence of different fan locations and number of fans on gas concentration. It can be concluded that: (1) the use of press-in method makes it more efficient to discharge gas out of the tunnel. (2) In order to make ventilation efficient, the fan should be arranged in a higher position and needs to be at a distance from the top of the tunnel. (3) Parallel use of two fans has better ventilation effect than single fan.

The short-lived positron-emitter carbon-11 (t1/2 = 20.4 min; b+, 99.8%) is prominent for labeling tracers for use in biomedical research with positron emission tomography (PET). Carbon-11 is produced for this purpose with a cyclotron, nowadays almost exclusively by the 14N(p,a)11C nuclear reaction, either on nitrogen containing a low concentration of oxygen (0.1–0.5%) or hydrogen (~ 5%) to produce [11C]carbon dioxide or [11C]methane, respectively. These primary radioactive products can be produced in high yields and with high molar activities. However, only [11C]carbon dioxide has some utility for directly labeling PET tracers. Primary products are required to be converted rapidly and efficiently into secondary labeling synthons to provide versatile radiochemistry for labeling diverse tracer chemotypes at molecular positions of choice. This review surveys known gas phase transformations of carbon-11 and summarizes the important roles that many of these transformations now play for producing a broad range of labeling synthons in carbon-11 chemistry.

In this work we perform a comparative study of the Kantowski-Sachs (KS) and Bianchi-I anisotropic universes with Modified Chaplygin gas (MCG) as matter source. We obtain the volume and scale factors as solutions to the Einstein Field Equations (EFEs) for the anisotropic universes, and check whether the initial anisotropy is washed out or not for different values of the MCG parameters present in the solution by obtaining the anisotropy parameters for each solution. The deceleration parameter is also obtained for each solution, the significance of which is discussed in the concluding section. Interestingly there are a number of notable results that appear from our study which help us to compare and contrast the two different anisotropic models along with proper understanding of the role of MCG as matter source in these models.

Fuel gas network (FGN) synthesis is a systematic method for reducing fresh fuel consumption in a chemical plant. In this work, we address the synthesis of fuel gas network using block superstructure originally proposed for process design and intensification (Demirel et.al. [1]). Instead of a classical source-pool-sink superstructure, we consider a superstructure with multiple feed and product streams. These blocks interact with each other through direct flows that connect a block with its adjacent blocks and through jump flows that connect a block with all blocks. The blocks with feed streams are viewed as fuel sources and the blocks with product streams are regarded as fuel sinks. Addition blocks can be added as pools when there exists intermediate operations among 9 source blocks and sink blocks. These blocks can be arranged in a I × J two-dimensional grid with I = 1 for problems without pools, or I = 2 for problems with pools. J is determined by the maximum number of pools/sinks. With this representation, we formulate fuel gas network synthesis problem as a mixed-integer nonlinear (MINLP) problem to optimally design a fuel gas network with minimal total annul cost. We present a real-life case study from LNG plant to demonstrate the capability of the proposed approach.

This article provides a comprehensive analysis of the global gas and liquefied natural gas (LNG) markets. The article begins by discussing the increasing demand for gas and LNG, particularly in Asia, as countries aim to transition to cleaner sources of energy. It explores how market volatility has led to energy security interventions and lasting economic and emissions impacts. It then explores the global supply and demand dynamics, highlighting the structural change expected in the market and the competition between Europe and Asia for limited new LNG supply. The article also focuses on Europe's increased flexibility and dependence on LNG imports, which have risen by 60% to 121 million tonnes, offsetting lower Russian pipeline imports. Furthermore, the article delves into global supply and demand dynamics, how the market is expected to remain tight, and how record gas and LNG prices have led to demand reductions. Additionally, it analyzes the future outlook and investment needs, highlighting the continued uptake of gas in heavy-duty transport and the need for further investment to avoid a supply-demand gap. The article concludes with an analysis of the implications for the future of the global gas and LNG markets.

The growing importance of hydrogen as an energy carrier in a future decarbonized energy system has led to a surge in its production plans. However, the development of infrastructure for hydrogen delivery, particularly in the hard-to-abate sectors, remains a significant challenge. While the construction of new pipelines entails substantial investment, repurposing existing pipelines offers a cost-effective approach to jump-starting hydrogen networks. Many European countries are exploring the possibility of utilizing their current pipeline infrastructure for hydrogen transport. Yet, a critical aspect requiring extensive research is the expansion planning of these networks to accommodate increased capacity in the future. This study investigates the utilization of existing natural gas pipeline infrastructure for hydrogen transportation as a cost-saving measure. It explores two expansion strategies, namely pipeline looping and compression, for repurposing a segment of a 342 km x 36inch existing pipeline, from the Escravos – Lagos gas pipeline system (ELPS) in Nigeria, for hydrogen transport. Employing the Promax® process simulator tool, the study assesses compliance with the API RP 14E and ASME B31.12 standards for hydrogen and hydrogen-methane blends. Both expansion strategies demonstrate acceptable velocity and pressure drop characteristics for hydrogen blends of up to 40%. Additionally, the increase in hydrogen content leads to heightened compression power requirements until approximately 80% hydrogen in the blends for compression, and a corresponding extension in looping length until around 80% hydrogen in the blend for looping. Moreover, the compression option proves to be more economically viable for all investigated proportions of hydrogen blends for the PS1-PS5 segment of the Escravos – Lagos gas pipeline case study. The percentage price differentials between the two expansion strategies reach as high as 495% for a 20% hydrogen proportion in the blend. This study offers valuable insights into the technical and economic implications of repurposing existing natural gas infrastructure for hydrogen transportation.

The offshore oil and gas working environment is an inherently dangerous one, with risks posed to physical safety on a daily basis. One neglected field of research is the added psychosocial stressors present in this environment. This research examined the experiences of offshore oil and gas workers through one-on-one online interviews which were recorded and transcribed. Transcripts were analysed through qualitative software NVivo, which generated themes and patterns for the responses given to questions which were developed through a focus group. The results of the analysis showed that multiple psychosocial stressors are present for this population, such as fear of speaking up, unsatisfactory company-provided facilities, work-life interference, work status, micromanaging, gender harassment and bullying. In addition, interviews identified that production and time pressures along with fatigue can influence accidents and mistakes. Climate factors also cause discomfort, however these are managed according to best practice by organisations. Due to the timing of the study, COVID-19 was a significant stressor for some, but not all, employees. In conclusion, offshore oil and gas workers face multiple stressors in a dangerous environment that may lead to devastating consequences.

Shrubs are a significant component of urban vegetation residing in parks, but they experience various influences of biotic and abiotic agents, among which aphids play an important role. In this work, the effect of aphid colonization on three shrub species in urban environment was examined. Fourteen parameters have been analyzed, describing photosynthetic pigment content and gas exchange to carbon, nitrogen, and hydrogen partition. While no significant effect of colonization was found on photosynthetic pigment parameters, the effect was significant on gas exchange parameters. The strongest effect aphid colonization achieved on nitrogen partition and C/N ratio, parameters that could be suggested in further similar studies. All parameters were classified in two groups according to principal component analysis, suggesting correlation between nitrogen and carbon content, C/N ratio, measured gas exchange parameters and chlorophyll a content. The ratio between net photosynthesis and dark respiration (A/K) was in the second group, suggesting that this parameter provide additional information on the effect of aphid colonization, and deserve special attention in further studies. There were differences in reaction of examined shrub species, where the strongest reaction by gross primary productivity (GPP) achieved Hybiscus syriacus, and by nitrogen partition and C/N ratio Spirea trilobata and Cydonia japonica.

When disposing of waste metal resources in landfills, environmental issues such as soil contamination may arise. Recycling these resources not only recovers valuable metals but also mitigates environmental pollution. Platinum (Pt), a valuable metal used in fuel cells for its high water production activity, will see increased future demand as a fossil fuel alternative. This study analyzes the environmental and resource reduction effects of recycled Pt, considering the growing emphasis on its recycling for stable supply and demand of Pt. The environmental impact and resource consumption of recycled Pt with primary Pt (from natural mines) were compared and analyzed using the Life Cycle Assessment (LCA) technique. Results revealed that resource consumption for primary Pt was 8.25E+01 kg Sb-eq./kg, significantly more than the 5.45E+00 kg Sb-eq./kg for recycled Pt. This represents an environmental reduction effect of approximately 93%. In the case of greenhouse gas emissions, primary Pt emitted 1.35E+04 kg CO2-eq./kg, while recycled Pt emitted 6.94E+02 kg CO2-eq./kg, resulting in an environmental reduction effect of approximately 95%. In conclusion, recycling Pt, compared to primary extraction, offers substantial environmental and resource reduction benefits. This study underscores the significance of recycling and highlights the potential environmental improvements achievable through sustainable practices.

In offshore drilling, accidents such as gas invasion, overflow, and kicks are inevitable, and they can escalate into blowouts and other catastrophic events that result in casualties and substantial economic losses. Therefore, maintaining drilling safety requires accurate monitoring of gas invasion and overflow. The majority of overflow monitoring methods currently utilized at drilling sites are threshold-based. However, monitoring parameters acquired during actual drilling operations frequently contain noise signals, making it difficult for threshold-based methods to strike a balance between improving accuracy and minimizing false positives. In this paper, Pattern Recognition-based Kick Detection (PRKD) is proposed as a novel method for diagnosing overflow in offshore drilling. This method utilizes the overflow evolution process by integrating multi-phase flow calculations, data filtering theory, pattern recognition theory, the Bayesian framework, and other theoretical models. The PRKD effectively detects and monitors gas intrusion and overflow based on single parameters by analyzing the shape and wave characteristics of the curves. The case analysis demonstrates that the proposed method for monitoring drilling overflow achieves high precision while maintaining a low false positive rate. By combining advanced computational techniques with pattern recognition algorithms, the PRKD improves the accuracy and reliability of kick detection, enabling proactive responses to potential risks, protecting the environment and human lives, and optimizing drilling operations.

The present study reports on the fabrication and performance of ammonia sensors based on single-walled carbon nanotubes (SWCNTs) coated with gold nanoparticles (AuNPs). The sensors were subjected to controlled concentrations of ammonia at two temperatures, namely 25 oC and 140 oC, and their response was monitored through successive cycles of ammonia exposure and nitrogen purging. The results demonstrate that the sputtering-based deposition of AuNPs on SWCNTs led to the best sensor performance, characterized by a rapid increase in resistance values upon exposure to ammonia, and efficient recovery at 140 oC. By contrast, the sensor with chemically impregnated AuNPs exhibited a slower response time. Furthermore, a novel device was developed that combined MoS2-AuNPs (sputtering)-SWCNTs, and it showed improved sensor performance compared to the devices with only AuNPs. Overall, the study provides valuable insights into the fabrication and optimization of SWCNT-based ammonia sensors for various applications, especially for detecting and quantifying small amounts of ammonia (concentrations below 1 ppm).

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.

In the search for new 2D materials beyond graphene with similar exemplary properties Stanene the new graphene relative was successfully synthesized and characterized in 2016 [14]. This new material which consists of atomically thin tin (Sn) atoms arranged in a hexagonal lattice has shown great promise in gas sensing applications in its pristine, doped and functionalized forms as evidenced by the recent research outputs following its discovery. Researchers have discovered that with its exotic properties it is highly efficient in the detection of the environmentally harmful gases like SO2, NO2, CO2, NH3 and can serve as a multifunctional gas sensor. In this focused and up-to-date review we aim to group the literature on first principles studies of stanene regards to its application for gas sensing and critically examine the success/failures of its multifunctional gas sensing properties as compared to graphene. We systematically present and discusses how structural deformations, defects and doping effect the gas sensing performance. Despite the impressive progress in the field of gas sensing with stanene shown by first principles calculations, many challenges in large scale synthesis, device fabrication and commercialization need to be addressed. The current review can help understand the current status and drawbacks of stanene and identify future directions in this field.

This work presents the dynamics of forest clearing in the Brazilian Amazon during the period 2006–2019 in which includes the approval of the new Brazilian Forest Code in 2012. The study was carried out in the Brazilian Amazon, Pará State and in the municipality of Novo Progresso (Pará State). The analysis was based on deforestation and fire hotspot datasets issued by the Brazilian Institute for Space Research (INPE), produced based on optical and thermal sensors onboard different satellites. Deforestation data was also used to assess greenhouse gas (GHG) emissions from the slash-and-burn practices. The work showed a good correlation between the occurrence of fires in the newly deforested area in the municipality of Novo Progresso and the slash-and-burn practices. The same trend was also observed in the Pará State, suggesting a common practice along the deforestation arch. The study indicated positive coefficients of determination of 0.72 and 0.66 between deforestation and fire occurrences for the municipality of Novo Progresso and Pará State, respectively. The increased number of fire occurrences in the primary forest suggests possible ecosystem degradation. Deforestation reported for 2019 surpassed 10,000 km2, a significant intensification comparatively higher than the previous ten years which was on an average of 6,760 km2. The steady increase of deforestation in the Amazon after 2012 has been a worldwide concern because of the forest loss itself as well as the massive GHG emitted in the Brazilian Amazon (295 million tons of net CO2 equivalent in the year 2019). Better correlation of deforestation and fires occurrences reported from satellite images confirmed the slash-and-burn practice and the secondary effect of deforestation, which degrades primary forest surrounding the deforested areas.

This paper presents a methodology for predictive and prescriptive analytics of complex engineering systems. The methodology is based on a combination of physics-based and data-driven modeling using machine learning techniques. Combining these approaches results in a set of reliable, fast, and continuously updating models for prescriptive analytics. The methodology is demonstrated with a case study of a jet-engine power plant preventive maintenance and diagnostics of its flame tube.

Simulation programs contain Computational Fluid Dynamics - CFD codes and are a useful tool used for gas flow through porous materials. Conducting numerical simulations allows for detailed analysis of hydrodynamic phenomena. The results of numerical modeling should always be verifiable based on experimental data. Only their compliance with the results of experimental tests is a determinant of the correctness of the applied method. As part of the work, experimental studies of hydrodynamics of gas flow through an isotropic porous material were carried out and numerical simulation for material of the same shape was used. In the CFD modeling Kolmogorov's hypothesis for the transport of kinetic energy of turbulence k and transport of dissipation rate of kinetic energy of turbulence ε was used.

Transient analysis of gas flow in pipeline was studied. Finite Element Method based on ANSYS FLOTRAN was used to account for changes in pressure, temperature and flow rate. Compressibility factor function of temperature and pressure was considered. For non-isothermal transient results, the pressure and the flowrate gave wave propagation as a result of slow transients created by demand condition at the outlet end of custody transfer. Results obtained were in agreement with the demand restrictions at the outlet end of custody transfer indicating that the predictions are accurate and reliable. The results demonstrated that the Finite Element Method gave accurate prediction of pressure, temperature and flowrate in transient gas studies. For steady state non-isothermal model, results showed that the magnitude of the average pressure drop was higher when pressure was predicted with constant compressibility factor, but the same average pressure drop was reduced when the pressure was predicted with variable compressibility factor, z. Since compressibility factor is a function of temperature and pressure, the above findings signifies that in the case when gas temperature does not stabilize, the prediction of pressure with isothermal model and constant compressibility factor will lead to significant errors.

Gas turbine installations (GTIs) are widely used to generate electrical and thermal energy mainly by burning gaseous fuels. The use of GTIs to burn hydrogen as part of the development of hydrogen energy technology is currently of particular interest. In order to assess the prospects of using GTIs in such a way, it is necessary, among other things, to understand the carbon footprint of the gas turbine as part of the carbon footprint of the entire life cycle of hydrogen. The article provides an overview of the results of previously published studies on life cycle assessment (LCA) of technically complex devices associated with the production and consumption of fuel and energy, which, from the point of view of the complexity of LCA, are most similar to gas turbine installation. The characteristics of the considered stages and resources used in the assessment of the stages of the life cycle of technically complex equipment are presented, including an analysis of the amount of materials used in production and construction. Taking into account its specific application in Russia, an assessment of greenhouse gas emissions at the stages of the GTI life cycle per MWh of produced capacity was carried out.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

Lubricated tribosystems such as main-shaft bearings in gas turbines have been successfully diagnosed by oil sampling for many years. In practice, the interpretation of wear debris analysis results can pose a challenge due to the intricate structure of power transmission systems and the varying degrees of sensitivity among test methods. In this work, oil samples acquired from the fleet of M601T turboprop engines were tested with optical emission spectrometry. Two-way analysis of variance (ANOVA) with interaction analysis and post hoc tests were carried out on measurement data from the whole fleet of the M-601T turboprop engines to study the impact of aluminum and zinc concentration on iron concentration. Finally, the developed model was used to evaluate the oil testing results for two specific engines of this type. Thanks to ANOVA, the assessment of engine health is based on a statistically proven correlation between the values of the dependent variable and the classifying factors.

Today, two very efficient methods for calculation of flow distribution per branches of a looped gas pipeline are available. Most common is improved Hardy Cross method, while the second one is so-called unified node-loop method. For gas pipeline, gas flow rate through a pipe can be determined using Colebrook equation modified by AGA (American Gas Association) for calculation of friction factor accompanied with Darcy-Weisbach equation for pressure drop and second approach is using Renouard equation adopted for gas pipeline calculation. For the development of Renouard equation for gas pipelines some additional thermodynamic properties are involved in comparisons with Colebrook and Darcy-Weisbach model. These differences will be explained. Both equations, the Colebrook’s (accompanied with Darcy-Weisbach scheme) and Renouard’s will be used for calculation of flow through the pipes of one gas pipeline with eight closed loops which are formed by pipes. Consequently four different cases will be examined because the network is calculated using improved Hardy Cross method and unified node-loop method. Some remarks on optimization in this area of engineering also will be mentioned.