Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

The nonlocality of entangled quantum mechanical systems is incompatible with the standard interpretation of special relativity as a single 4D Minkowskian metric spacetime. The difficulty is that the definition of a spacetime interval between any pair of events precludes any form of nonlocal interaction, even the relatively benign non-signaling correlations. By an application of the relativity principle, and the use of the space ←→ time symmetry of the Lorentz boost I propose here a reinterpretation of special relativistic spacetime. This new ontology consists of a set of coexisting 3+1D spaces (‘framespaces’), each containing unique content in the form of a complex density. These spaces are related by the Lorentz boost, and coupled pairwise in a manner dictated by the Lorentz transformation. The inter-space coupling acting on the spacetime content gives rise to a nonlocal wave phenomenon, which is identified as quantum wave mechanics. The interspace coupling strength is then inversely proportional to Planck’s constant. The coexistence of multiple spaces is interpreted as momentum superposition, implying that momentum is the fundamental physical basis of quantum superposition. This new spacetime interpretation of quantum mechanics has many consequences, including explanations of quantum non-locality, the spacetime role of Planck’s constant, quantum measurement as a symmetry-breaking process and the redundancy of description of gauge theory.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

A fundamental tool in mathematical physics is the logarithmic Sobolev inequality. A quantitative version proven by Carlen with a remainder involving the Fourier-Wiener transform is equivalent to an entropic uncertainty principle more general than the Heisenberg uncertainty principle. In the stability, the remainder is in terms of an entropy, not a metric. Recently, a stability result for H¹ was obtained by Dolbeault, Esteban, Figalli, Frank, and Loss in terms of an L^p norm. Afterwards, Brigati, Dolbeault, and Simonov discussed the stability problem involving a stronger norm. A full characterization with a necessary and sufficient condition to have H¹ convergence is identified in this paper. Moreover, an explicit H¹ bound via a moment assumption is shown. Also, the L^p stability of Dolbeault, Esteban, Figalli, Frank, and Loss is proven to be sharp.

With the rapid spread of built-in GPS handheld smart devices, the trajectory data from GPS sensors has grown explosively. Trajectory data has spatio-temporal characteristics and rich information. Using trajectory data processing techniques can mine the patterns of human activities and the moving patterns of vehicles in the intelligent transportation systems. A trajectory similarity measure is one of the most important issues in trajectory data mining (clustering, classification, frequent pattern mining, etc.). Unfortunately, the main similarity measure algorithms with the trajectory data have been found to be inaccurate, highly sensitive of sampling methods, and have low robustness for the noise data. To solve the above problems, three distances and their corresponding computation methods are proposed in this paper. The point-segment distance can decrease the sensitivity of the point sampling methods. The prediction distance optimizes the temporal distance with the features of trajectory data. The segment-segment distance introduces the trajectory shape factor into the similarity measurement to improve the accuracy. The three kinds of distance are integrated with the traditional dynamic time warping algorithm (DTW) algorithm to propose a new segment–based dynamic time warping algorithm (SDTW). The experimental results show that the SDTW algorithm can exhibit about 57%, 86%, and 31% better accuracy than the longest common subsequence algorithm (LCSS), and edit distance on real sequence algorithm (EDR) , and DTW, respectively, and that the sensitivity to the noise data is lower than that those algorithms.

Ploidy is a significant type of genetic variation, describing the number of chromosome sets per cell. Ploidy evolves in natural populations, clinical populations, and lab experiments, particularly in fungi. Despite a long history of theoretical work on this topic, predicting how ploidy will evolve has proven difficult, as it is often unclear why one ploidy state outperforms another. Here, we review what is known about contemporary ploidy evolution in diverse fungal species through the lens of population genetics. As with typical genetic variants, ploidy evolution depends on the rate that new ploidy states arise by mutation, natural selection on alternative ploidy states, and random genetic drift. However, ploidy variation also has unique impacts on evolution, with the potential to alter chromosomal stability, the rate and patterns of point mutation, and the nature of selection on all loci in the genome. We discuss how ploidy evolution depends on these general and unique factors and highlight areas where additional experimental evidence is required to comprehensively explain the ploidy transitions observed in the field and the lab.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Despite the recognized influence of maximum or acceleration strength on combat techniques and countermovement jump (CMJ) performance, the relationship between body segment weights and combat techniques remains unexplored. This study aimed to examine the impact of body segment weights, including striking arm weight (SAW), kicking leg weight (KLW), and trunk weight (TW), on the dynamics of direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and CMJ performance. Sixteen male military cadets (22.3±1.8 years, 181.4±7.0 cm, 83.0±8.1 kg) performed combat techniques, with performance measured by using a force plate and body segment weights assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis was applied. Results indicated a strong correlation between KLW and FK impulse (r = 0.64, p ≤ 0.01) and CMJ impact force (r = 0.80, p ≤ 0.01). SAW showed moderate correlations with DP impulse (r = 0.53, p ≤ 0.05) and ES impulse (r = 0.54, p ≤ 0.05). Additionally, FK peak and impact forces were strongly correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01), and FK peak force moderately correlated with CMJ peak velocity (r = 0.63, p ≤ 0.05). These findings suggest targeted arm strength training could enhance striking abilities, while improvements in leg acceleration strength may directly boost kicking performance and vertical jump capabilities, which are crucial in combat scenarios.

In this paper, our goal is to establish the relationship between solutions of local sharp vector variational type inequality and sharp efficient solutions of vector optimization problems, also Minty local sharp vector variational type inequality and sharp efficient solutions of vector optimization problems, under generalized approximate $\eta$-convexity conditions for locally Lipschitzian functions

Iron and zinc are essential micronutrients required for growth and health. Deficiencies of these nutrients are highly prevalent among populations, but can be alleviated by supplementation. Cross-sectional studies in humans showed positive association of serum zinc levels with hemoglobin and markers of iron status. Dietary restriction of zinc or intestinal specific conditional knock out of ZIP4 (SLC39A4), an intestinal zinc transporter, in experimental animals demonstrated iron deficiency anemia and tissue iron accumulation. Similarly increased iron accumulation has been observed in cultured cells exposed to zinc deficient media. These results together suggest a potential role of zinc in modulating whole body iron metabolism. Studies in intestinal cell culture models demonstrate that zinc induces iron uptake and transcellular transport via induction of divalent metal iron transporter-1 (DMT1) and ferroportin (FPN) expression, respectively. It is interesting to note that intestinal cells are exposed to very high levels of zinc through pancreatic secretions, which is a major route of zinc excretion from the body. Therefore, zinc appears to be modulating the iron metabolism possibly via regulating the DMT1 and FPN1 levels. Herein we critically reviewed the available evidence to hypothesize novel mechanism of Zinc-DMT1/FPN axis in regulating intestinal iron absorption and tissue iron accumulation to facilitate future research aimed at understanding the yet elusive mechanisms of iron and zinc interactions.

Using a joint statistical analysis, we test a four-dimensional FLWR model embedded in a five-dimensional bulk based on the Nash-Greene embedding theorem. Performing a Markov Chain Monte Carlo (MCMC) modelling, we combine observational data sets as those of the recent Pantheon type Ia supernovae, Baryon Acoustic Oscillations (BAO) and the angular acoustic scale of the Cosmic Microwave Background (CMB) to impose restrictions on the model and correlating the model parameters to mimick an equation of state. From statistical classifiers as the Akaike Information Criterion (AIC) and Bayesian Information Criterion (BIC), we use the Jeffreys' scale and find a strong evidence favoring a statistically consistence with a dynamical Dark energy (CPL parameterization) and a relative consistence with both ΛCDM and ωCDM models. Moreover, we find that the transition redshift used as a cosmic discriminator with the best fit z_t=0.634 ± 0.014 at 1-σ C.L. with a range scenario for late time sharp transitions.

Firstly, a new set of Quasi-Cubic Trigonometric Bernstein basis with two tension shape parameters is constructed, and we prove that it is an optimal normalized totally basis in the framework of Quasi Extended Chebyshev space. And the Quasi-Cubic Trigonometric Bézier curve is generated by the basis function and the cutting algorithm of the curve are given, the shape features (cusp, inflection point, loop and convexity) of the Quasi-Cubic Trigonometric Bézier curve are analyzed by using envelope theory and topological mapping; Next we construct the non-uniform Quasi-Cubic Trigonometric B-spline basis by assuming the linear combination of the optimal normalized totally positive basis have partition of unity and continuity, and its expression is obtained. And the non-uniform B-spline basis is proved to have totally positive and high-order continuity. Finally, the non-uniform Quasi Cubic Trigonometric B-spline curve and surface are defined, the shape features of the non-uniform Quasi-Cubic Trigonometric B-spline curve are discussed, and the curve and surface are proved to be continuous.

We monitored the water quality and hydrological conditions of a horizontal subsurface constructed wetland (HSSF-CW) in Beijing, China, for 2 years. We simulated the area rate constant and the temperature coefficient with the first-order kinetic model. We examined the relationships between the nitrogen (N) removal rate, N load, seasonal variations in the N removal rate, and environmental factors, such as the area rate constant, temperature, and dissolved oxygen (DO). The effluent ammonia (NH₄⁺-N) and nitrate (NO₃⁻-N) concentrations were significantly lower than the influent concentrations (p<0.01, n=38). The NO₃⁻-N load was significantly correlated with the removal rate (R²=0.9566, p<0.01), but the NH^₄+-N load was not correlated with the removal rate (R²=0.0187, p>0.01). The area rate constants of NO₃⁻-N and NH₄⁺-N at 20 °C were 27.01±26.49 and 16.63±10.58 m∙yr⁻¹, respectively. The temperature coefficients for NO₃⁻-N and NH₄⁺-N were estimated at 1.0042 and 0.9604, respectively. The area rate constants for NO₃⁻-N and NH₄⁺-N were not correlated with temperature (p>0.01). The NO₃⁻-N area rate constant was correlated with the corresponding load (R²=0.9625, p<0.01). The NH₄⁺-N area rate was correlated with DO (R²=0.6922, p<0.01), suggesting that the factors that influenced the N removal rate in this wetland met Liebig's law of the minimum.

Nonlinear nonparametric statistics (NNS) algorithm offers new tools for curve fitting. A relationship between k-means clustering and NNS regression points is explored with graphics showing a perfect fit in the limit. The goal of this paper is to demonstrate NNS as a form of unsupervised learning, and supply a proof of its limit condition. The procedural similarity NNS shares with vector quantization is also documented, along with identical outputs for NNS and a k nearest neighbours classification algorithm under a specific NNS setting. Fisher's iris data and artificial data are used. Even though a perfect fit should obviously be reserved for instances of high signal to noise ratios, NNS permits greater flexibility by offering a large spectrum of possible fits from linear to perfect.

This study focused on demonstrating the potential of classification algorithm in the chemical composition characterization of transiting exoplanets. The Python-based module PLATON 5.3 for forward modelling of transiting planet spectra was used to simulate a set of transmission spectra of an exoplanet with size R_p = 1.40*R_jupiter, and mass M_p = 0.73*M_jupiter orbiting around the host star of size M_s = 1.16*M_sun and surface temperature of 1200 Kelvin. The gas composition of the exoplanet atmosphere was varied at low and high levels of 3-gas mix of CO₂, O₂, N₂ and CH₄ resulting to eight classes of spectra. The transit spectra were then used as input data to a forward neural network classifier with the eight gas composition classes as target outputs. The trained classifier achieved at most 97.9% overall accuracy.

The authors developed a wealth curve (bell curve) that can predict a group of individuals’ wealth based on the composite intelligence score which is calculated based on the sum of the intelligence quotient and emotional awareness score. The intelligence quotient was defined as one's ability to perform, comprehend and learn, and emotional awareness was defined as the emotional ability to recognize and make sense of emotions. To move towards the right on the X-axis of the Kabir wealth curve (e.g., accumulate more wealth), individuals must improve emotional awareness and choose a professional career path that lands higher income, calculated risk-taking, and being connected with individuals that can lead to financial deals. Similarly, those facing social injustice can accumulate more wealth by improving emotional awareness, which will help them navigate challenging environments.

Full-scale wind turbine technology has been widely developing in the recent years and condition monitoring techniques assist at the scope of making 100\% technical availability a realistic perspective. In this context, several retrofitting techniques are being used for further improving the efficiency of wind kinetic energy conversion. This kind of interventions is costly and, furthermore, the estimation of the energy enhancement is commonly provided under the hypothesis of ideal conditions, as for example absence of wakes between nearby turbines. A precise quantification of the energy gained by retrofitting is therefore precious in real conditions, that can be very different from ideal ones. In this work, three kinds of retrofitting are studied through the operational data of test case wind farms: improved start-up through pitch angle adjustment near the cut-in, aerodynamic blade retrofitting by means of vortex generators and passive flow control devices, extension of the power curve by raising cut-out and high wind speed cut-in. SCADA data are employed and reliable methods are formulated for estimating the energy improvement from each of the above retrofitting. Further, an insight is provided about wind turbine functioning under very stressing regimes, as for example high wind speeds.

The purpose of this study was to describe ocular surface and anterior eye segment findings in various types of ichthyoses. Methods: This was a single-center prospective observational study. The study group consisted of five patients (P1-P5) aged 13–66 years. Multimodal imaging was performed, including slit-lamp examination, swept-source optical coherence tomography (SS-OCT), and in vivo confocal microscopy (IVCM). Results: All patients were diagnosed with moderate to severe dry eye disease (DED). Corneas showed a significant pattern of irregularity, with a significant difference between the corneal thickness at the apex (CAT) and corneal thinnest thickness (CTT), ranging from 5 to 375 µm. Three patients were diagnosed with ectasia patterns based on SS-OCT. All patients showed abnormalities in at least one Fourier index parameter for at least one eye at 3 or 6 mm, on keratometric, anterior, or posterior analyses. IVCM examination revealed changes in all corneal layers. Conclusions: By combining the results of multimodal im-aging, we were able to detect preclinical abnormalities, distinguish characteristic changes com-mon to ichthyosis, and reveal the depth and characteristics of corneal abnormalities. Therefore, patients with ichthyosis should be examined for DED and ectatic disorders early in clinical prac-tice.

Let $\mathcal{\mathcal{S}}_{\cos}^{\ast}$ denote the class of normalized analytic functions $f$ in the open unit disk $\mathbb{D}$ satisfying the subordination $\dfrac{zf^{\prime}(z)}{f(z)}\prec\cos z$. In the second section of this article we find the sharp upper bounds for the initial coefficients $a_{3}$, $a_{4}$ and $a_{5}$ and the sharp upper bound for module of the Hankel determinant $|H_{2,3}(f)|$ for the functions from the class $\mathcal{S}_{\cos}^{\ast}$. The first result of the next section deals with the sharp upper bounds of the logarithmic coefficients $\gamma_{3}$ and $\gamma_{4}$ and we found in addition the sharp upper bound for $\left|H_{2,2}\left(F_{f}/2\right)\right|$. For obtaining these results we used the very useful and appropriate Lemma 2.4 of N.E. Cho et al. [Filomat 34(6) (2020), 2061--2072], and the technique for finding the maximum value of a three variable function on a closed cuboid. All the maximum found values were checked by using MAPLE\texttrademark{} computare software, and we also found the extremal functions in each cases. All of our present results are the best ones and give sharp versions of those recently published in [Hacet. J. Math. Stat. 52, 596--618, 2023].

The features of a class of cubic curves with a shape factor are analyzed by means of the theory of envelope and topological mapping. The effects of the shape factor on the cubic curves are made clear. Necessary and sufficient conditions are derived for the curve to have one or two inflection points, a loop or a cusp, or to be locally or globally convex. Those conditions are completely characterized by the relative position of the edge vectors of the control polygon and the shape factor. The results are summarized in a shape diagram, which is useful when the cubic parametric curves are used for geometric modeling. Furthermore we discussed the influences of the shape factor on the shape diagram and the ability for adjusting the shape of the curve.

A remarkable feature of US federal investments in human genetics has been the availability of parallel funding for studies examining ethical, legal and social implications (ELSI). This funding has allowed ELSI researchers to develop new strategies to understand genetics, evaluate the benefits of genetic testing, and propose health policy that maximize the promise while minimizing harms. Despite successes, a consequence of this investment is the preoccupation with what is arguably the least actionable system of biomolecules, human DNA. In contrast, the most actionable system of biomolecules, the metabolome, is grossly understudied, despite its often more alarming ELSI.

We develop a quantitative microscopic theory of decaying Turbulence by studying the dimensional reduction of the Navier-Stokes loop equation for the velocity circulation. We have found an infinite dimensional manifold of solutions of the Navier-Stokes loop equation\cite{M93, M23PR} for the Wilson loop in decaying Turbulence in arbitrary dimension $d >2$. This family of solutions corresponds to a fractal curve in complex space $\mathbb C^d$, described by an algebraic equation between consecutive positions plus a nonlinear periodicity condition. We derive the constrained SDE for the evolution of the fractal curve at a fixed moment of physical time as a function of an auxiliary stochastic time. We expect this stochastic process to cover our fixed manifold of the solutions of the decaying Turbulence. The energy density of the fluid decays as $\mathcal E_0/t$, where $\mathcal E_0$ is an initial dissipation rate. Presumably, we have found a new phase of extreme Turbulence yet to be observed in real or numerical experiments.

We analyse the light curve in the R-band gathered during the 2015/16 observing season of OJ287. We did a search for QPOs using several methods in wide time domain. No statistically significant periods were found in the high frequency domain both in the ground data and also in K2 observations. In the longer periods domain the Lomb-Scargle periodogram revealed several peaks above the 99\% significance level. The longest one, about 95-day, corresponds to the ISCO period of the more massive SMBH. The 43-day period could be an alias or can be attributed to accretion in the form of two armed spiral wave.

Objective: To investigate whether the relationships between acute care occupational therapy (OT) and physical therapy (PT) utilization and community discharge are moderated by functional or physical performance at discharge among individuals hospitalized with traumatic brain injury (TBI). Setting: 14 acute care hospitals in the state of Colorado. Participants: We studied 5,599 adults hospitalized with TBI between June 2018 and April 2021. Design: In a secondary analysis of de-identified electronic health record (EHR) data, multivariable moderation logistic regression models were performed to calculate odds ratios (ORs) for the likelihood of community discharge among patients who utilized OT/PT services. Main Measures: Functional (activities of daily living [ADL]) and physical (mobility) performance at discharge, OT and PT utilization, and community discharge status. Results: Overall, 67% of patients discharged to the community. The mean age of the sample was 55 years (SD = 20 years). Most participants were male (64%) and non-Hispanic white (72%). Mean hospital length of stay was 6 days (SD = 6 days). Both OT and PT utilization (OT: OR= 1.21, 95% CI [1.11, 1.33]; PT: OR= 1.22, 95% CI [1.14, 1.30]) and discharge ADL and mobility scores (ADL: OR= 1.34, 95% CI [1.30, 1.39]; mobility: OR= 1.38, 95% CI [1.33, 1.42]) were significantly and positively associated with community discharge. The OT and PT utilization-by-discharge ADL and mobility interaction terms yielded slightly negative, but statistically significant moderation effects in both models (ORs= 0.99, 95% CIs [0.98, 1.00]); indicating the magnitude of the OT and PT utilization effect diminished as ADL and mobility scores increased. Several sociodemographic characteristics and clinical factors were also independently associated with community discharge in both models (p-values

Needlestick and other sharp injuries (NSIs) are critical occupational hazard for healthcare workers. Exposure to blood and body fluids through NSIs increases the risk of transmission of blood-borne pathogens among them. The objectives of this study were to estimate the one-year incidence of NSIs and investigate its associated factors among the healthcare workers in Saudi Arabia. A cross-sectional online survey was conducted between October and November 2021. A total of 361 healthcare workers participated in the survey from all over Saudi Arabia. The one-year incidence of NSIs among healthcare workers is estimated at 22.2%. More than half of the injury event (53.8%) was not reported to the authority by the healthcare worker. Incidence of NSIs was highest among the physicians (36%) and is followed by nurses (34.8%), dentists (29.2%), and medical technologists (21.1%). The likelihood of injury is higher (OR: 2.51; 95% CI: 1.04, 6.03) among the works aged 26 – 30 years compared to the 20 – 25 years age group and the workers directly deal with needles or other sharp objects while working (OR: 5.90; 2.69, 12.97). The high incidence rate of injury and low reporting rate highlight the needs of an education program targeting healthcare providers with higher risk.

Glaucoma is a blinding disease largely caused by increased resistance to drainage of fluid from the eye’s anterior chamber, resulting in elevated intraocular pressure (IOP). A major site of fluid outflow regulation and pathology is the trabecular meshwork (TM) at the entrance of the eye’s drainage system. We aimed to characterize the structural and functional properties of a newly developed tissue-engineered anterior segment eye culture model. We hypothesized that repopulation of a decellularized TM with non-native TM cells could restore aspects of normal TM. The decellularization protocol removed all cells and debris while preserving the ECM. Seeded cells localized to the TM region and progressively infiltrated the meshwork ECM. Cells reached a distribution comparable to control TM after four days of perfusion culture. After a perfusion rate increase challenge, tissue-engineered cultures reestablished normal IOPs (reseeded = 13.7±0.4 mmHg, decellularized = 35.2±2.2 mmHg, p < 0.0001). eGFP expressing CrFK control cells caused a high and unstable IOP (27.0±6.2 mmHg). In conclusion, we describe a readily available, storable, and biocompatible scaffold for anterior segment perfusion culture of non-native cells. Tissue-engineered organs demonstrated similarities to native tissues and may reduce the need for scarce donor globes in outflow research.

Compared with the traditional robots on earth, space robotics present additional difficulties including complicated, multi–body dynamics (including anti–resonances absent with earthly robotic systems), space environmental forces and torques, communication delays, and high expense. Pointing accuracy requirements necessitate control algorithms that can accommodate flexible, multi–body dynamics particularly. The high cost of placing systems in space drives necessarily lightweight systems lacking structural stiffness. Natural frequencies of space robot vibration are often so low, the act of implementing control torques causes structural resonance. Seeking improved performance, this manuscript introduces and compares a dozen options, revealing seventy–percent reduction in tracking error may be achieved with only ten percent increase in control effort. Prequel work recommended tracking sinusoidal shaped trajectories while structurally filtering the first mode’s resonance and anti–resonance. The future research recommended in that prequel is manifest in this present work which recommends a simpler system of lower order, eliminating the notch compensation of the first resonance while no longer compensating the first anti–resonance.

Infrastructure monitoring, inspection, repair, and replacement in space is crucial for continued usage and safety, yet it is expensive, time-consuming, and technical very challenging. New robotics technologies and artificial intelligence algorithms are potentially novel approaches that may alleviate such demanding operations using existing or novel sensing technologies. Space structures must necessarily be very light weight due to high costs of placing robots in space. Several methods are proposed and compared to control highly flexible space robotics, where a key challenge is the presence of flexible resonant modes at frequencies so low as to reside inside typical feedback controller bandwidths. Such conditions imply the very action of sending control signals to the ultra-light weight robotics will cause structural resonance. Implementations of incrementally increasing order are offered, achieving over ninety percent performance improvement in trajectory tracking errors, while improvement using unshaped methods merely achieve twenty-four percent improvement in direct comparison (where the only modification is the proposed control methodology). Based on superior performance, single-sinusoidal trajectory shaping is recommended with a corollary benefit of preparing future research into applying deterministic artificial intelligence whose current instantiation relies on single-sinusoidal, autonomous trajectory generation.

In this paper, a geometric model is introduced for Neutrosophic data problem for the first time. This model is based on neutrosophic sets and neutrosophic relations. Neutrosophic control points are defined according to these points, resulting in neutrosophic Bézier curves.

Recent state-of-the-art scene text recognition methods have primarily focused on horizontal text in images. However, in several Asian countries, including China, large amounts of text in signs, books, and TV commercials are vertically directed. Because the horizontal and vertical texts exhibit different characteristics, developing an algorithm that can simultaneously recognize both types of text in real environments is necessary. To address this problem, we adopted the direction encoding mask (DEM) and selective attention network (SAN) methods based on supervised learning. DEM contains directional information to compensate in cases that lack text direction; therefore, our network is trained using this information to handle the vertical text. The SAN method is designed to work individually for both types of text. To train the network to recognize both types of text and to evaluate the effectiveness of the designed model, we prepared a new synthetic vertical text dataset and collected an actual vertical text dataset (VTD142) from the Web. Using these datasets, we proved that our proposed model can accurately recognize both vertical and horizontal text and can achieve state-of-the-art results in experiments using benchmark datasets, including the street view test (SVT), IIIT-5k, and ICDAR. Although our model is relatively simple as compared to its predecessors, it maintains the accuracy and is trained in an end-to-end manner.

In this work, the manufacture of thin walls with sharp corners has been optimized by adjusting the limits of a 3-axis cartesian kinematics through data recorded and analyzed off-line, such as axis speed, acceleration and the positioning of the X and Y axes. The study was carried out with two powder materials (SS316L and IN718) using the directed energy deposition process with laser. 1 mm thick walls were obtained with only one bead per layer and straight/sharp corners at 90º. After adjusting the in-position parameter G502 for positioning precision on the FAGOR 8070 CNC system, it has been possible to obtain walls with minimal accumulation of material in the corner, and with practically constant layer thickness and height, with a radii of internal curvature between 0.11 and 0.24 mm for two different precision configuration. The best results have been obtained by identifying the correct balance between the decrease in programmed speed and the precision in the positioning to reach the point defined as wall corner, with speed reductions of 29% for a programmed speed of 20 mm/s and 61% for a speed of 40 mm/s. The walls show minimal defects such as residual porosities, and the microstructure is adequate.

Anesthetics reduce cardiac functions and lower blood pressure (BP), potentially causing excessive BP reduction in dehydrated patients or those with heart conditions, such as coronary artery disease (CAD). Considering the increased prevalence of cardiovascular disease with age, anesthesiologists must be cautious about BP reduction during general anesthesia in older adults. In the present case, an undiagnosed CAD patient in a hypovolemic state experienced a significant systolic blood pressure drop to the 50s during propofol and sevoflurane anesthesia. Despite the use of vasopressors, excessive hypotension persisted, leading to anesthesia suspension. Subsequent cardiac examinations, including computed tomography heart angio and calcium score, and coronary angiogram, revealed a near total occlusion of the left main coronary artery and the formation of collateral circulation. After 5 days of hydration and anticoagulation medications and confirmation of normovolemic state, general anesthesia was attempted again and successfully induced; a normal BP was maintained throughout the surgery. Thus, it is important to conduct a thorough cardiac evaluation and maintain normovolemia for general anesthesia in older adults.

ST-segment elevation myocardial infarction (STEMI), a major cause of mortality worldwide, has been shown through epidemiological studies to have a relationship with short-term exposure to air pollutants; however, the association between air pollutants and the outcome of STEMI has not been well studied. The aim of this study was to estimate the impact of air pollutants on the outcomes of STEMI. Data on particulate matter <2.5 μm (PM2.5), <10 μm (PM10), nitrogen dioxide (NO2), and ozone (O3) at each of the 11 air monitoring stations in Kaohsiung City were collected between January 1, 2012, and December 31, 2017. Medical records of non-trauma patients aged > 20 years who had visited the ED with a principal diagnosis of STEMI were extracted. The primary outcome measure was in-hospital mortality. After adjusting for potential confounders and meteorological variables, we found that an increase in the interquartile range (IQR) in NO2 was associated with an elevated risk of in-hospital mortality in patients with STEMI. Moreover, during the warm season, an IQR increase in NO2 corresponded to a higher risk of in-hospital mortality in patients with STEMI on lag 3 (OR=3.266; 95% CI:1.203–8.864, p=0.02). Conversely, an IQR increase in PM10 was associated with an increased risk of in-hospital mortality in patients with STEMI on lag 3 (OR=2.792; 95%CI:1.115–6.993, p=0.028) during the cold season. Our study suggests that exposure to NO2 (during warm season) and PM10 (during cold season) may contribute to a higher risk of poor prognosis in patients with STEMI.

Background: Flattening the curve refers to community isolation measures that keep the daily number of disease cases at a manageable level for medical providers. Efforts to completely contain the COVID – 19 have failed. As there is currently no vaccine or specific medication to treat COVID-19, the only way to flatten the curve is through collective action of mitigation efforts. Objectives: The study was carried out with aim to study the effect of mitigation efforts in reducing the overall COVID -19 attack rate and flattening the curve of COVID-19 in Egypt. Methods: Secondary data in the situation reports of WHO, Worldometer and Egyptian MoHP Report about the COVID-19 epidemic in Egypt were analyzed till June 27, 2020. Survival analysis was carried out to determine the cumulative proportional survival of COVID-19. The Susceptible Infected Recovered (SIR) model was used to study the epidemic dynamics of COVID-19 pandemic. Results: In Egypt in the fourth week after exposure β was 0.17 and γ = 0.07. The fraction of infectious individuals will grow exponentially as the exponential growth rate was 0.10, with an epidemic time of 7 days. R in 22 ^nd June was 0.80 (less than one person infected) where β=0.21 and γ =0.26. There was reduction in the actual overall attack rate at 22^nd June of 96 % of its value without intervention with a cumulative proportional survival of 0.89. There was flattening of the curve. Conclusion and Recommendation: Mitigation efforts of Egypt had succeeded in flattening the curve of COVID-19 Pandemic. Even though, strengthening all the mitigation efforts to keep the exposure probability, as well as the transmission rate as low as possible is mandatory for containment of the epidemic.

In the field of autonomous vehicles, lane detection and control plays an important role. In autonomous driving the vehicle has to follow the path to avoid the collision. A deep learning technique is used to detect the curved path in autonomous vehicles. In this paper a customized lane detection algorithm was implemented to detect the curvature of the lane. A ground truth labelling tool box for deep learning is used to detect the curved path in autonomous vehicle. By mapping point to point in each frame 80-90% computing efficiency and accuracy is achieved in detecting path.

The heavy demand of water resources from the Zarqa River Basin (ZRB) has resulted in a base-flow reduction of the River from 5m³/s to less than 1m³/s. This paper aims at predicting Curve Numbers (CN) as a baseline scenario and proposing restoration scenarios for ZRB. The method includes classifying the soil type and land use, predicting CNs, and proposing CN restoration scenarios. Prediction of existing CNs will be in parallel with the runoff prediction using the US Army Corps of Engineers HEC-1 Model, and Rainfall-Runoff Model (RRM). The models have been set up at the land use distribution of 0.3% water body, 9.3% forest and orchard, 71% mixture of grass, weeds, and desert shrubs, 7.0% crops, 4.0% urban areas, and 8.4% bare soil. The results show that CN under dry condition are 59, 78 under a normal condition and 89 under a wet condition. During vegetation period, CN are 52, 72 and 86 for the dry, normal and wet condition respectively. The restoration scenarios; CN decreases runoff, and increases soil moisture when using the contours, terraces and crop residues. Analyzing results of CN scenarios will be a fundamental tool to support end-users related to their targets to achieve watershed restoration.

The study of the currently known >3,000 species of snakes can provide valuable insights into the evolution of their genomes. Deinagkistrodon acutus, also known as Sharp-nosed Pit Viper, one hundred-pacer viper or five-pacer viper, is a venomous snake with significant economic, medicinal and scientific importance. Widely distributed in southeastern China and South-East Asia, D. acutus has been primarily studied for its venom. Here, we employed next-generation sequencing to assemble and annotate a highly continuous genome of D. acutus. The genome size is 1.46 Gb; its scaffold N50 length is 6.21 Mb, the repeat content is 42.81%, and 24,402 functional genes were annotated. This study helps to further understand and utilize D. acutus and its venom at the genetic level.

Controlling functional properties of matter and combine them for engineering a functional device is nowadays a common direction of scientific community. For instance, heterogeneous magnetic nanostructures can make use of different types of geometrical and compositional modulations to achieve the control of the magnetization reversal along with the nano-entities and thus enabling the fabrication of spintronic, magnetic data storage and sensing devices, among others. In this work, diameter modulated FeNi nanowires are fabricated paying special effort to obtain sharp transition regions between two segments of different diameters (from about 450 nm to 120 nm), enabling precise control over the magnetic behavior of the sample. Micromagnetic simulations performed on single bi-segmented nanowires predict a double step magnetization reversal where the wide segment magnetization switches near 200 Oe through a vortex domain wall, while at 500 Oe the magnetization of the narrow one is reversed through a corkscrew like mechanism. Finally, these results are confirmed with magneto-optic Kerr effect measurements at the transition of isolated bi-segmented nanowires. Furthermore, macroscopic vibrating sample magnetometry is used to demonstrate that the magnetic decoupling of nanowire segments is the main phenomenon occurring over the entire fabricated nanowires.

RNA virus polymerases carry out multiple functions necessary for successful genome replication and transcription. A key tool for molecular studies of viral RNA-dependent RNA polymerases (RdRps) is a ‘minigenome’ or ‘minireplicon’ assay, in which viral RdRps are reconstituted in cells in the absence of full virus infection. Typically, plasmids expressing the viral polymerase protein(s) and other co-factors are co-transfected along with a plasmid expressing an RNA encoding a fluorescent or luminescent reporter gene flanked by viral untranslated regions containing cis-acting elements required for viral RdRp recognition. This reconstitutes the viral transcription/replication machinery and allows viral RdRp activity to be measured as a correlate of reporter protein signal. Here we report the first development of a plasmid-based minigenome assay for species A rotavirus, using a firefly luciferase reporter gene.

Currently the bimatoprost implant (DURYSTA) is approved for a single administration secondary to concern for progressive corneal endothelial cell (CEC) loss with intracameral administration. In order to better understand the cause of CEC loss and other adverse events (AEs) with intracameral administration, multimodal imaging of the implant utilizing optical coherence topography (OCT), robotic ultrasound and bio microscopy video recording was utilized. Inherently the anterior chamber is a non-confined space. In certain examples the implant assumed a round and spotted structure as it picked up iris pigment as it migrated around the anterior chamber. Accordingly, we explored delivery of the implant in the middle segment behind the iris and in front of the pseudophakic lens. We then evaluated the suitability of various imaging modalities to assess the implant in this location. For middle segment administration, the ArcScan Insight 100 robotic ultrasound provided resolution and repeatability sufficient to monitor the implant behind the iris. This preliminary study hypothesizes that DURYSTA migration in the anterior chamber is the main source of AEs. Through use of a confined location, the middle segment, the implant is unlikely to migrate and cause CEC loss while also delivering drug closer to its site of action, the ciliary body. Further efforts are underway to understand the suitability of the middle segment for serial DURYSTA administration to maximize intraocular pressure lowering while minimizing AEs.

Machine learning models facilitate the search for non-linear relationships when modeling hydrological processes, but they are equally effective for automation at the data preparation stage. The tasks whose automation was analyzed consisted in estimating changes in the roughness of a mountain streambed and the extent of floods from images. The Segment Anything Model (SAM) developed this year by Meta was used for this purpose. Images from many years from the Wielka Puszcza mountain stream located in the Polish Carpathians were used as the only input data. The model was not additionally trained for the described tasks. The model can be run in several modes, but the two most appropriate were used in this study. The first one is available in the form of a web application, while the second one is available in the form of a Jupyter notebook run in the Google Colab environment. Both methods do not require specialized knowledge and can be used by virtually any hydrologist. In the roughness estimation task, the average Intersection over Union (IoU) ranges from 0.55 for grass to 0.82 for shrubs/trees. Ultimately, it was possible to estimate the roughness coefficient of the mountain streambed between 0.027 and 0.059 based solely on image data. In the task of estimation of the flood extent, when selecting appropriate images, one can expect IoU at the level of at least 0.94, which seems to be an excellent result considering that SAM is a general-purpose segmentation model. It can therefore be concluded that SAM model can be a useful tool for a hydrologist.

Anterior segment dysgenesis (ASD) encompasses a wide spectrum of developmental abnormalities of the anterior ocular segment, including congenital cataract, iris hypoplasia, aniridia, iridocorneal synechiae, as well as Peters, Axenfeld, and Rieger anomalies. Here, we report a large five-generation Caucasian family exhibiting atypical syndromic ASD segregating with a novel truncating variant of FOXC1. The family history is consistent with highly variable autosomal dominant symptoms including isolated glaucoma, iris hypoplasia, aniridia, cataract, hypothyroidism, congenital heart anomalies, and cystic kidney disease. Whole exome sequencing revealed a novel variant [c.313_314insA; p.(Tyr105*)] in FOXC1 that disrupts the alpha-helical region of the DNA-binding forkhead box domain. In vitro studies using a heterologous cell system revealed aberrant cytoplasmic localization of FOXC1 harboring the Tyr105* variant, likely precluding downstream transcription function. Meta-analysis of the literature highlighted the intrafamilial variability related to FOXC1 truncating alleles. This study highlights the clinical variability in ASD and signifies the importance of combining both clinical and molecular analysis approaches to establish a complete diagnosis.

In this paper, modification of dual-Halbach permanent magnet (PM) array is investigated to improve performance of tubular linear machine, in terms of flux density and output power. Instead of a classical Halbach array with only radial and axial PMs, proposed model involves insertion of mig-magnets, which have magnetized angle shifted from the reference magnetized angles of axial and radial PMs. This structure leads to elimination of flux leakage and concentration of flux linkage in middle of the coil; therefore, the performance of machine is increased.

The present paper provides a new definition for dual spline curves in a geometric intuitive way based on adaptive curve refinement techniques. The dual spline is an implementation of the interpolatory subdivision scheme for curve modeling, which is comprised of polynomial segments of different degrees. Specially, the dual spline curves are mainly aims to solve the difficult geometry defeaturing problems in the existing computer-aided technology. Dual spline curves maintain various desirable properties of conventional curve modeling methods, such as local adaptive subdivision, high interpolation accuracy and convergence, continuous and discontinuous boundary approximation. By adding fictitious and intrinsic nodes inside or at the vertices of interpolation elements, the dual spline is flexible and convenient for approximating a set of ordered points or discrete segments. Combined with the Lagrange interpolation polynomial and meshless method, the proposed approach is capable of approximating the non-smooth boundary for geometry defeaturing. Experimental results are given to verify the validity, robustness, and accuracy of the proposed method.

3D city models integrate heterogeneous urban data from multiple sources in a unified geospatial representation, combining both semantics and geometry. Although in the last decades, they are predominantly used for visualization, today they are used in a large range of tasks related to exploration, analysis, and management across multiple domains. The complexity of urban processes and the diversity of urban environment bring challenges to the implementation of 3D city models. To address such challenges, this paper presents the development process of a 3D city model of a single neighborhood in Sofia city based on CityGML 2.0 standard. The model represents the buildings in LOD1 with a focus on CityGML features of related to the buildings like building part, terrain intersection curve and address. Similar building models of 18 cities provided as open datasets are explored and compared in order to extract good modeling practices. As a result, workflows for generation of 3D building models in LOD1 are elaborated and improvements in the feature modeling are proposed. Two options of building model are examined: modeling of a building as a single solid and modeling of a building with separate building parts. Finally, the possibilities for visualization of the model in popular platforms such as ArcGIS Pro and Cesium Ion are explored.

Polyhedral oligomeric silsesquioxane (POSS) is a suitable nanoscale reinforcement for thermosetting polymers, such as epoxy resin systems in order to modify its mechanical, thermal, and chemical properties. The inclusion of POSS in the epoxy resin at higher loading (greater than 1 wt.%), however, introduces the ductility during the fracture behavior of these nanocomposites. Consequently, the J-integral is used to quantify the fracture behavior of these materials and characterize the crack growth resistance curve against stable crack growth. A range of nanocomposites is prepared by adding 0.5, 1, 3, 5, and 8 wt.% of glycidyl POSS into DGEBF epoxy resin cured with an amine-based curing agent. From the fracture toughness experiment the load-displacement result confirms that when the POSS reinforcement is greater than 1 wt.%, the fracture behavior of the nanocomposite changes from brittle to ductile. For both brittle and ductile nanocomposites, the addition of POSS molecules improves the crack initiation toughness. The development of POSS–POSS compliant domains are reported previously, is attributed for this change in the failure behavior. The fractured images of POSS–epoxy nanocomposites, obtained using scanning electron microscopy, show that the increase in fracture resistance at higher values of POSS loading occurs due to the extensive shear yielding. Meanwhile, the increased fracture toughness at lower values of POSS loading occurs due to crack pinning and crack deflection.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

Spent nuclear fuel and high-level radioactive waste can be disposed in deep horizontal drillholes in sedimentary, metamorphic, or igneous rocks. Horizontal drillhole disposal has safety, operational, and economic benefits: The repository is deep in the brine-saturated zone far below aquifers in a reducing environment of formations that can be shown to have been isolated from the surface for millions of years; its depth provides safety against inadvertent intrusion, earth¬quakes, and near-surface perturbations; it can be placed close to the reactors and interim storage facilities, minimizing transportation; disposal costs per ton of waste can be kept substantially lower than for mined repositories by its smaller size, reduced infrastructure needs, and staged imple¬mentation; and, if desired, the waste could be retrieved using “fishing” technology. In the proposed disposal concept, corrosion-resistant canisters containing unmodified fuel assemblies from commercial reactors would be placed end-to-end in up to 50 cm diameter horizontal drill¬holes, a configuration that reduces mechanical stresses and keeps the temperatures below the boiling point of the brine. Other high-level wastes, such as capsules containing 137Cs and 90Sr, can be disposed in small-diameter drillholes. We provide an overview of this novel disposal concept and its technology, discuss some of its safety aspects, and compare it to mined repositories and the deep vertical borehole disposal concept.

In this paper, the overall performance of Cu-(In,Ga)-Se₂ (CIGSe) solar cells was improved in the ultraviolet (UV)–visible wavelength region by two-segment process. In which, adjusting DC sputtering powers (20–40 W) for absorbers (segment I), and metal-alloy compositions (CdS, ZnO/CdS, ZnMgO/CdS and ZnMgO) for buffers (segment II) were explored and characterized. Upon choosing the optimal-30-W CIGSe-absorber (with 0.95-CGI ratio) sputtered by the segment-I process, the Cu-rich film can distinctly boost grain growth, thus reducing the trap state density. After segment-II process as the toxic-CdS alternative, the optimal Zn_0.9Mg_0.1O-alloy buffer can reach the best conversion efficiency (η = 8.70%) was attained for the environmental protection. Meanwhile, and the overall internal/external quantum efficiencies (IQE/EQE) were improved by 13.15%, respectively for the 2.48–3.62-eV bandgap (short wavelength) range. The developed photovoltaic (PV) module (with 9 optimum-CIGSe cells) exhibits acceptable stability with a variance within ±5% over the 60-day experiment. This discovery in PV-device research contributes to a new scientific understanding of renewable energy. Furthermore, this study undeniably enhances the progress of practical applications for PV-modules in alignment with sustainable development goals. It also actively supports the development of eco-friendly communities.

To solve the problem of deformation and stress in segments when a full-face hard rock tunnel boring machine (TBM) tunnel for an urban subway passes through existing buildings, a three-dimensional mechanical calculation model of TBM tunneling under existing buildings was established based on numerical analysis to comprehensively study the spatial attributes of tunnel segments during TBM tunneling. The Qingdao Metro Line 1 TBM tunnel in the hard rock stratum of Xiaobei District passes through existing buildings. The results indicated that (1) the stress and deformation of the segments were different at different positions. The horizontal and vertical stress and displacement of the segments in front of the building were significantly affected by the building. When the segment was not in the area below the horizontal plane of the building, the vertical stress of the segment was significantly greater than the two stresses in the horizontal direction. (2) The vertical displacements of the vault and the arch bottom were the largest, and the influence of vertical accessories was stronger when the segment was closer to the building.(3) When the tunnel was excavated to approximately one tunnel diameter in front of the building, the building was affected. If the surrounding rock is unstable, the excavation face may collapse and the ground surface may sink, possibly leading to inclination, cracking, and uneven settlement of the building.

The purpose of this article is to simulate data transmission and calculate traffic parameters in SAGIN air segment for which Ad Hoc network of flying drones is considered as a model. Traffic modeling is based on the manet-routing-compare example from the ns3 simulator library, which has been supplemented with the code for calculation packet losses, throughput/goodput, and message transmission delays. The program allowed considering drones movement at both low and high speeds from 3.6 km/h to 72 km/h. The dependences of traffic losses on data transmission power, transaction sizes and data transmission rate are obtained and analyzed. The distribution of the average effective arrival rate λ and the throughput/goodput for drones has been studied. Comparing traffic characteristics in models with different numbers of drones allows judging how the required quality of service can be achieved by choosing the right transmission parameters.

This study provides a contribution to the research field of 3D printed earthen buildings, focusing, for the first time, on the load-bearing capacity of these structures. The study involves the entire production and testing process of the earthen elements, from design, to the preparation of the mixture and the 3D printing, up to the uniaxial compression test on a wall segment. The results indicate that 3D printed earthen elements have a compressive strength of 2.32 MPa, comparable to that of rammed earth structures. The experimental data also made it possible to draw conclusions on the action of the infill, which seems to have the function of stopping the propagation of cracks. This has a positive effect on the overall behavior of 3D printed earthen elements, since it avoids the onset of dilative behavior in the final stages of the load test and maintains ultimate load values higher than 50% of the maximum load.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

The Internet of Things (IoT) is a technological paradigm that has gained significant momentum that last decade and, among others, enables the development of intelligent and interoperable device networks. In this respect, it has triggered the creation and evolution of VANETs (Vehicular Ad Hoc Networks), which are initially implemented in order to guarantee the safety of the drivers and the avoidance of traffic accidents. The drawback is that this fast evolution flags serious concerns as far as the privacy of users is concerned, while the population of attackers or entities that try to eavesdrop and intercept information has significantly increased. This imposes a serious risk for drivers moving across a Smart City. The research presented in this paper aims to evaluate privacy protection mechanisms in VANET environments, based on their efficiency and security level ensured, considering the fact that VANETs provide limited resources to users/drivers. Moreover, the usage of the elliptic curve cryptography in reduced resources environments is discussed. Finally, this paper compares the performance of three cryptographic algorithms, i.e., Elliptic Curve Cryptography (ECC), Hyperelliptic Curve Cryptography genus 2 (HECC-2) and HECC genus 3 (HECC-3), employed for an efficient authentication and safe message transmission mechanism in VANETs, targeting to extract conclusions related to the implementation of each cryptographic scheme in this specific application area.

Leclère et al.¹ have outlined the possibility of a biodiversity transition for the 21^st century, a line of thinking equivalent to the Forest Transition theory and what it says about forest cover globally². The authors use a suite of global models to explore the impacts on global biodiversity of interventions on land-use, consumption and production patterns. They outline six strategies that have the potential to stop the downfall of global terrestrial biodiversity by 2050 and redress it to a pre-1970 level by 2100. Although robust, sophisticated and well-illustrated, the conclusions of this paper cannot alone be used to frame a post-2020 biodiversity strategy.

We have proposed a model considering two equally sized population (group A and group B) with low and high levels of disease tolerance. We have argued that in the more tolerant group (group B) the progression of the disease with respect to time will be slow with lower number of infections at any given time. We attribute this effect to the innate immunity which advantageously, can also be one of the major contributing factors for flattening the curve. We have compared the growth of Covid-19 disease in various countries to understand this effect.

Let ${\mathcal{SR}}^*$ be the class of starlike functions with real coefficients, i.e., the class of analytic functions $f$ which satisfy the condition $f(0)=0=f'(0)-1$, Re{z f'(z) / f (z)} > 0, for $z\in\mathbb{D}:=\{z\in\mathbb{C}:|z|<1 \}$ and $a_n:=f^{(n)}(0)/n!$ is real for all $n\in\mathbb{N}$. In the present paper, the sharp estimates of the third Hankel determinant $H_{3,1}$ over the class ${\mathcal{SR}}^*$ are computed.

Ants of the genus Solenopsis are important invasive pests in the world. Due to their high dispersion capacity, aggressive behavior and because they feed on various sources of vegetable and animal protein, these insects have caused serious damage to public health and agriculture. The control has usually been carried out through the use of organosynthetic insecticides. However, due to the ecological and environmental impacts caused by the use these products, more sustainable alternatives have been sought for their control. Faced with these problems and due to the scarcity of registered products for the control of these insects, we aimed with this study to synthesize and evaluate the anticidal potential of carvacrol derivatives. The lethal and sublethal effects caused by these derivatives were compared with the essential oil of Lippia gracilis (50.7% carvacrol) and with the base molecule — carvacrol. Carvacryl benzoate was the most toxic derivative to Solenopsis sp. with an LD50 of 3.20 g/ mg. This compound was about 2 and 7.6 times, more toxic than carvacrol at the doses needed to kill 50 and 90% of populations, respectively. The workers of Solenopsis sp. showed a rapid reduction in survival when exposed to carvacrol (LT50 = 8.43h) and carvacryl benzoate (LT50 = 8.87h). Insects treated with sublethal doses of the compounds did not show significant effects on self-cleaning, allogrooming and aggregation, with the exception of those treated with L. gracilis essential oil. The oil increased self-cleaning and reduced allogrooming and aggregation. Ants treated with carvacrol and carvacryl benzoate showed greater distance and speed when compared to the control. These compounds decreased meanders and angular velocity. When live workers were exposed to dead individuals at the LD90 of the compounds, carvacryl benzoate was the derivative that most reduced insects survival, due to horizontal transfer. These results show the potential of the carvacrol derivative — carvacryl benzoate — for the alternative management of ants of the genus Solenopsis sp.

Despite the recognized influence of body mass on combat techniques, the relationship between body segment mass (BSM) and combat moves remains unexplored. This study aimed to examine the relationship between striking arm mass (SAM), kicking leg mass (KLM), and body mass (BM) with the dynamic forces of the direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and countermovement jumps (CMJ) performance. Sixteen male military cadets (22.3 ± 1.8 years, 181.4 ± 7.0 cm, 82.1 ± 8.5 kg) performed combat techniques, with performance measured by using a force plate and body segment mass assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis, the Wilcoxon test, and Cohen's d were applied. Results indicated the relationship between KLM or BM and FK impulse (r = 0.64, p = 0.01; r = 0.52, p = 0.04, respectively) and CMJ impact force (r = 0.80, p ≤ 0.01; r = 0.70, p ≤ 0.01, respectively). Moreover, FK peak and impact forces were moderately correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01). The highest relationship was found between KLM and FK impulse; however, the difference in variability explained by KLM versus body mass is only 12%. This suggests that knowledge of BSM did not provide a significantly better estimate of the dynamic forces of the punches and FK than BM.

Sepsis is a life-threatening organ dysfunction caused by a dysregulated host response to infection, with septic cardiomyopathy being a common and severe complication. Despite its significant clinical impact, the molecular mechanisms underlying sepsis-induced cardiomyopathy (SICM) remain incompletely understood. In this study, we performed a comparative analysis of whole transcriptome profiles in two widely used mouse models of septic cardiomyopathy, the cecal ligation and puncture (CLP) model and the lipopolysaccharide (LPS) model. Our aim was to identify key genes and pathways involved in the development of septic cardiomyopathy and to evaluate the similarities and differences between the two models. Our findings suggested that 1) both methods can induce septic heart dysfunction within 24 hours; 2) distinct whole transcriptome expression profiles are revealed; 3) potentially different pathways are involved in causing heart failure in sepsis. The comprehensive comparison provides valuable insights into the molecular basis of septic cardiomyopathy and contributes to the ongoing search for effective treatment strategies, triggered by different factors for SICM.

A method was developed to perform shape optimization of a tidal stream turbine hydrofoil using a multi-objective genetic algorithm. A bezier curve parameterized the refrence hydrofoil profoil NACA 63815. Shape optimization of this hydrofoil maximized its lift-to-darg ratio and minimized its pressure coefficient, thereby increasing the turbines power output power and improving its cavitation characteristics. The Elitist Non-dominated Sorting Genetic Algorithm (NSGA-II) was employed to perform the shape optimization. A comparative study of two-and three-dimensional optimizations was carried out. The effect of varing the angle of attack on the quality of optimized results was also studied. predictions based on two-dimensional panel method results was also studied. Preditions based on a two-dimensional panel method and on a computational fluid dynamics code were compared to experimental measurments.

This letter introduces a frequency response characteristic (FRC) curve and its application in high renewable power systems. In addition, the letter presents a method for fast frequency response assessment and frequency nadir prediction without performing dynamic simulations using detailed models. The proposed FRC curve and fast frequency response assessment method are useful for operators to understand frequency response performance of high renewable systems in real time.

Ingrown toenails are a commonly occurring foot complaint. The condition occurs when the nail plate pierces the sulcus, giving rise to pain, inflammation and infection. As the skin attempts to heal itself, hypergranulation tissue may form. This is a case report of phenolic nail surgery treatment for a bilateral presentation with sharp resection of hypergranulation tissue performed in only one (the lateral) of the two affected sulci. Sharp resection of the residual medial hypergranulation tissue was performed two months after the index procedure when this had not settled. The case highlights the potential role of sharp resection in the overall improvement of treatment outcomes.

This paper presents a V2G strategy to flatten the daily load curve by considering the charging and discharging location of the electric vehicle to help understand the effect of the load generated by charging and discharging of the electric vehicle on the power grid. Based on the estimated share of electric vehicles, the assumption that electric vehicles go to work in the morning and leave in the afternoon was set, and the electric vehicle discharge power was calculated by reflecting both the characteristics of vehicles that go to work in the morning and the SMP1 and SMP2 plans. In addition, the electric vehicle charging power was calculated by reflecting the characteristics of vehicles returning home from work in the afternoon and the TOU rate system. In other words, in order to establish an efficient V2G strategy, a charging/discharging type-specific modeling was developed that considered all the characteristics of an electric vehicle commuting vehicle, and charging and discharging daily load using SMP1 and SMP2 rate plans for morning discharge and TOU1 and TOU2 rate plans for afternoon charging were applied. After calculating the curve, this value was compared and analyzed to evaluate the effect on grid leveling by adding the existing load. The analysis provides an accurate understanding of the impact of EV charging and discharging loads on the power grid according to V2G strategies. In this paper, it is helpful to apply EV charge and discharge management technology to avoid grid overload and minimize grid expansion by leveling the grid daily load curve by applying appropriate SMP and TOU rates through the establishment of an efficient V2G strategy by charge and discharge modeling.

This article describes the methodology used to identify the mathematical model that describes the correlations between the input parameters of an experiment and the parameters being followed. As a technological process, the aerodynamic separation was chosen, respectively, the behavior of a solid particle within an ascending vertical airflow. The experimental data obtained were used to identify two parameters, the average linear velocity, and the angular velocity, and through the Table Curve 3D program was developed a mathematical model which describes the dependence between the input parameters (the shape and size of the solid particle and the velocity of the airflow) and the monitored parameters. In order to determine a single mathematical equation that describes as accurately as possible the correlation between the input variables and those obtained, a pyramid-type analysis was designed. The determination of the mathematical equation started from the number of equations generated by the Table Curve 3D program, then the equations with a correlation coefficient greater than 0.85 were chosen, and finally, the common equations were identified. Respecting the working methodology was identified one equation which has for the average linear velocity a correlation coefficient r2 between 0.88-0.99 and 0.86-0.99 for the angular velocity.

Despite their limited spatial extent, freshwater ecosystems host remarkable biodiversity, including one third of all vertebrate species. This biodiversity is declining dramatically: globally, wetlands are vanishing three times faster than forests and freshwater vertebrate populations have fallen more than twice as steeply as terrestrial or marine populations. Threats to freshwater biodiversity are well- documented but co-ordinated action to reverse this decline is lacking. We present an Emergency Recovery Plan to “bend the curve” of freshwater biodiversity loss. Priorities for action include: 1) accelerating implementation of environmental flows, 2) improving water quality, 3) protecting and restoring critical habitats, 4) managing exploitation of freshwater species and riverine aggregates, 5) preventing and controlling non-native species invasions, and 6) safeguarding and restoring river connectivity. We recommend revised targets and indicators for the Convention on Biological Diversity and the Sustainable Development Goals, and investment in enabling conditions at national, river basin and local scales.

Evaporating liquid sessile drop deposited on horizontal surface is an important object of applications (printing technologies, electronics, sensorics, medical diagnostics, hydrophobic coatings, etc.) and theoretical investigations (microfluidics, self-assembly of nanoparticle, crystallization of the solute, etc.). The arsenal of formulas for calculating the slow evaporation of an axisymmetric drop of capillary dimensions deposited on a flat solid surface is reviewed. Such characteristics as vapor density, evaporation flux density, total evaporation rate are considered. Exact solutions obtained in the framework of the Maxwellian model, in which the evaporation process of the drop is limited by vapor diffusion from the drop surface to the surrounding air, are presented. The summary covers both well-known results obtained during the last decades and new results published by us in the last few years, but practically unknown to the wide scientific community. The newest formulas, not yet published in refereed publications, concerning exact solutions for a number of specific contact angles are also presented. In addition, new approximate solutions are presented for the first time (total evaporation rate and mass loss per unit surface area per unit time in the whole range of contact angles ), which can be used in modeling without requiring significant computational resources.

Inteins, often referred to as protein introns, are highly mobile genetic elements that invade conserved genes throughout the tree of life. Inteins have been found to invade a wide variety of key genes within actinophages. While in the process of conducting a survey of these inteins in actinophages we discovered that one protein family of methylases contained a putative intein, and two other unique insertion elements. These methylases are known to occur commonly in phages as orphan methylases (possibly as a form of resistance to restriction-modification systems). We found that the methylase family is not conserved within phage clusters and has a disparate distribution across divergent phage groups. We determined that two of the three insertion elements have a patchy distribution within the methylase protein family. We also found that the third insertion element is likely a second homing endonuclease, and that all three elements (the intein, the homing endonuclease, and what we refer to as the ShiLan domain) all have different insertion sites that are conserved in the methylase gene family. Furthermore, we find strong evidence that both the intein and ShiLan domain are partaking in long distance horizontal gene transfer events between divergent methylases in disparate phage hosts within the already dispersed methylase distribution. The reticulate evolutionary history of methylases and their insertion elements reveals high rates of gene transfer and within-gene recombination in actinophages.

Ho Chi Minh City (HCMC), the most crowded city and economic hub of Viet Nam, has been experiencing land subsidence over the past decades. This effort aims to contribute the spatial distribution of subsidence in HCMC in its horizontal and vertical components using synthetic aperture radar interferometry (InSAR) time series. To this purpose, an advanced Persistent Scatterers and Distributed Scatterers (PSDS) InSAR technique was applied to two European Space Agency (ESA) Sentinel-1 datasets consisting of 96 ascending and 202 descending images, acquired from 2014 to 2020 over the HCMC area. A time series of 33 COSMO-SkyMed ascending images was also used for comparison. The combination of ascending and descending satellite passes is used to decompose the light of sight velocities into horizontal east-west and vertical components. Taking into account the presence of east-west horizontal motion, our findings indicate that the accuracy of the decomposed vertical velocity can be improved by up to 3 mm/year for Sentinel-1 data. The obtained results revealed that subsidence is most pronounced in the areas along the Sai Gon River, in the northwest-southeast axis, and in the southwest of the city, with a maximum value of 80 mm/yr, which is in accordance with the findings of the literature. The amplitude of east-west horizontal velocities is relatively small and large-scale eastward movement can be observed in the west of the city at a rate of 3-5 mm/yr. This confirmed that the displacement in Ho Chi Minh City area is mainly vertical downward. Together, these results reinforced the remarkable suitability of ESA's SAR Sentinel-1 for subsidence applications, even for non-European countries such as Vietnam and Southeast Asia.

The aim of this work is to evaluate the impact of proposed modifications to conventional capturing and discharging effluents devices in Subsurface Flow Wetland (SSFW) systems. Main modifications proposed consist on extending the influence of the capture and discharge device in such a way that the SSFW width and height are fully covered. Additionally an SSFW prototype was built as pilot including the proposed modifications and the impact of the innovative device is measured based on the efficiency of the Chemical Oxygen Demand (COD) removal as compared to a traditionally built SSFW. The results show that for the innovative device, the COD removal was 10% higher than for the conventional device.

Purpose: To evaluate three different microincisional ab interno trabeculectomy procedures in a porcine eye perfusion model. Methods: In perfused porcine anterior segments, 90 degrees of trabecular meshwork (TM) were ablated using the Trabectome (T; n = 8), Goniotome (G; n = 8), or Kahook device (K; n = 8). After 24 hours, additional 90 degrees of TM were removed. Intraocular pressure (IOP) and outflow facility were measured at 5 µL/min and 10 µL/min perfusion to simulate an elevated IOP. Structure and function were assessed with canalograms and histology. Results: At 5 µL/min infusion rate, T resulted in a greater IOP reduction than G or K from baseline (76.12% decrease versus 48.19% and 47.96%, P = 0.013). IOP reduction between G and K was similar (P = 0.420). Removing another 90 degrees of TM caused an additional IOP reduction only in T and G but not in K. Similarly, T resulted in the largest increase in outflow facility at 5 µL/min compared with G and K (first ablation: 3.41 times increase versus 1.95 and 1.87; second ablation: 4.60 versus 2.50 and 1.74) with similar results at 10 µL/min (first ablation: 3.28 versus 2.29 and 1.90 (P = 0.001); second ablation: 4.10 versus 3.01 and 2.01 (P = 0.001)). Canalograms indicated circumferential flow beyond the ablation endpoints. Conclusions: T, G and K significantly increased the outflow facility. In this model, T had a larger effect than G and K.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

Backgroundː Previous studies have shown that both serum creatinine and D-dimer levels were associated with atherosclerotic coronary artery disease (CAD). We aimed to determine whether DCR is associated with coronary Gensini score in patients with ST-elevation myocardial infarction (STEMI). Methodsː 337 STEMI patients with complete D-dimer and creatinine and other necessary information were included in the analysis. According to the values of the DCR, patients were divided into the lower DCR group (DCR ≤ 1.42, n = 173) and the higher DCR group (DFR > 1.42, n = 174), and the differences between the two groups were compared. Multivariate linear and multivariate logistic regression analyses were performed to determine independent predictors of Gensini score. Resultsː High DCR group had higher Gensini score compared with low DCR group (P < 0.05). DCR was positively correlated with Gensini score (r=0.493, P < 0.001). Multiple linear regression analysis showed that Previous MI (r=11.312, P=0.035) and DCR (r=5.129, P<0.001) were independent risk factors associated with Gensini score. Multivariate logistic regression analysis showed that, compared to the group 1, DCR is independent risk factor for Group 2, Group 3, Group 4 (P <0.001). DCR is positively correlated with coronary Gensini score in STEMI patients and can be used as an independent predictor of higher Gensini score. Conclusionsː As a new and useful clinical marker, DCR is positively correlated with coronary Gensini score in STEMI patients and can be used as an independent predictor of higher Gensini score.

Elliptic curve cryptography (ECC) over prime fields relies on scalar point multiplication realized by point addition and point doubling. Point addition and point doubling operations consist of many modular multiplications of large operands (256 bits for example), especially in projective and Jacobian coordinates which eliminate the modular inversion required in affine coordinates for every point addition or point doubling operation. Accelerating modular multiplication is therefore important for high-performance ECC. This paper presents the hardware implementations of modular multiplication algorithms, including 1) Interleaved modular multiplication (IMM), 2) Montgomery modular multiplication (MMM), 3) Shift-sub modular multiplication (SSMM), 4) SSMM with advance preparation (SSMMPRE), and 5) SSMM with CSAs and sign detection (SSMMCSA) algorithms, and evaluates their execution time (the number of clock cycles and clock frequency) and required hardware resources (ALMs and registers). Experimental results show that SSMM is 1.76 times faster than IMM, and SSMMCSA is 3.21 times faster than IMM. We also present the ECC hardware implementations based on the Secp256k1 protocol in affine, projective, and Jacobian coordinates using the IMM, SSMM, SSMMPRE, and SSMMCSA algorithms, and investigate their cost and performance. Our ECC implementations can be applied to the design of hardware security module systems.

This paper presented a method for calculating daily load curves by considering charging and discharging locations of electric vehicles to help to understand the impact of loads generated by charging and discharging of electric vehicles on the power grid. Based on the estimated PEVs’ share, the PEVs discharge power was calculated to reflect both the characteristics of the arriving vehicle in the morning and the SMP plan after establishing a assumption that the electric vehicle arrived at work in the morning and the electric vehicle arrived at home in the afternoon for each of the charging/discharging locations, that is, work and home, of electric vehicles in the city. After calculating the daily load curve for each charging/discharging power type for the PEVs charging strategy, which takes into account both the characteristics of the vehicle arriving at home in the afternoon and the TOU fare system and the characteristics of the vehicle arriving at work in the morning and the SMP fare system, it was analyzed by comparing the impact assessment on the grid by adding the existing load. The results of this paper provide an accurate understanding of the impact of PEVs charging and discharging loads on the power grid. The results should help to establish PEVs charging and discharging load management plans to prevent overloading the power grids with appropriate SMP and TOU tariffs while curbing the reinforcement and expansion of power grids as much as possible.

(1) Background: This manuscript introduces the "Lines and Dots" (LAD) technique, a novel method for administering Botulinum Toxin Type A (BoNT-A) in treating horizontal forehead lines. This technique emphasizes precision in targeting nerve endplates, considering individual anatomical variations, and optimizing treatment efficacy. (2) Methods: The LAD technique focus on using the frontalis muscle contraction dynamics to identify the specific distribution of the supraorbital and supratrochlear nerves It involves creating a grid of predetermined lines and points on the forehead that align with nerve paths and motor endplate zones. (3) Results: By targeting injections along these precise lines and points, the LAD technique ensures more effective utilization of BoNT-A. This approach not only enhances the toxin's effect but also allows for a reduction in the overall dosage. The strategic placement of injections results in a more natural, symmetrical, and sustained therapeutic effect, ensuring an improved aesthetic outcome. (4) Conclusions: The LAD technique represents a significant advancement in the realm of cosmetic injectables. It offers a tailored, patient-specific approach, maximizing the effectiveness of BoNT-A injections for treating forehead lines while minimizing risks and enhancing patient satisfaction. This method underscores the importance of a deep anatomical understanding and precision in cosmetic procedures.

Horizontal transfer of transposons (HTT) is an important source of genomic evolution in eukaryotes. The HTT dynamics is well characterized in eukaryotes including insects however, but there is a huge gap of knowledge about HTT regarding many eukaryotes’ species. In this study we analyzed the events of the HTT between Rhus gall aphids (Hemiptera) and other insects. We analyzed the Mariner-like transposable elements (MLEs) belongs to Rhus gall aphids for the possible HT events. The MLEs have patchy distribution and have high similarity over the entire length of element with insects MLEs from different orders. We selected representative sequences from the Rhus gall MLEs and identified five events of HT between MLEs of Rhus gall aphids and other insects from five different orders. We also found multiple HTT events among the MLEs of insects from the five orders which demonstrate that these Mariner elements have been involved in recurrent HT between these six order of insects. Our current study closed the knowledge gap of HTT and reported the events between Rhus gall aphids and other insects for the first time. We believe that this study about HTT events will help to understand the evolution and spread of transposable elements in the genomes of Rhus gall aphids.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

Wastewater (WW) analysis is a critical step in various operations such as control of a WW treatment facility, and speeding-up the analysis of WW quality can significantly improve such operations. This work demonstrates the capability of neural network (NN) regression models to estimate WW characteristic properties such as biochemical oxygen demand (BOD), chemical oxygen demand (COD), ammonia (NH3-N), total dissolved substances (TDS), total alkalinity (TA), and total hardness (TH) by training on WW spectral reflectance in the visible to near-infrared spectrum (400nm-2000nm). The dataset contains samples of spectral reflectance intensity, which were the inputs, and the WW parameter levels (BOD, COD, NH3-N, TDS, TA, and TH), which were the outputs. Various NN model configurations were evaluated in terms of regression model fitness. The mean-absolute-error (MAE) was used as the metric for training and testing the NN models, and the coefficient of determination (R2) between the model predictions and true values was also computed to measure how well the NN models predict the true values. With online spectral measurements, the trained neural network model can provide non-contact and real-time estimation of WW quality at minimum estimation error.

We argue that a very large class of quantum pure states of isolated macroscopic bodies have sharply peaked energy distributions, with their width relative to the average scaling between $\sim N^{-1}$ and $\sim N^{-1/2}$, with $N \gg 1$, the number of atoms conforming the body. Those states are dense superpositions of energy eigenstates within arbitrary finite or infinite energy intervals that decay sufficiently fast. The sharpness of the energy distribution implies that closed systems in those states are {\it microcanonical} in the sense that only energy eigenstates very near to the mean energy contribute to their thermodynamic evolution. Since thermodynamics accurately describes processes of macroscopic bodies and requires that closed systems have constant energy, our claim is that these pure states are typical of macroscopic systems. The main assumption beneath the energy sharpness is that the isolated body can reach thermal equilibrium if left unaltered. We argue that such a self-sharpness of the energy in macroscopic bodies indicates that the First Law of Thermodynamics is statistical in character.

Steel fibres provides ductility to concrete structures. This in turn gives possibility to replace or reduce conventional reinforcement in structural elements. In this study the focus is on structural walls and the fibres as potential replacement for horizontal reinforcement in areas where vertical re-bars are needed. An experimental study was conducted, in which prismatic specimens with longitudinal re-bars were subjected to centric loading. Ten samples with 12 specimens in each were tested. The parameters considered were: fibre content, concrete cover for the longitudinal bars, and presence of stirrups. Self-compacting concrete with 30 and 60 kg/m3 steel fibres was used. The influence of fibres on maximum load, stiffness, and ductility of the specimens is evaluated. The results show that fibres eliminated brittle collapse and spalling of concrete at failure. Samples with fibres tend to have reduced maximum force and stiffness but increased ductility. The specimens with fibre content of 60 kg/m3 showed more ductile behaviour than the ones with minimum amount of conventional stirrups. The study suggests that combination of steel fibres and conventional re-bars can lead to less qualitative compactness of the self-compacting concrete, which in turn may reduce load bearing capacity and stiffness of the structure.

Drilling vibrations has been identified as a key performance limiter that prevents successful energy transfer from the surface to the bit. The resultant irregular bit rotation speed causes drilling challenges like poor hole quality and reduction in rate of penetration to name a few. Amongst other vibration suppression techniques, active control of vibrations is widely used and recommended. Active control system utilizes a closed loop feedback control to continuously adapt to downhole vibrations detected at the surface. The system requires regular tuning and upgrades which is done experimentally before field deployment. The paper presents a PID based experimental tuning of horizontal and vertical strings for irregular RPM. In doing so, the paper highlights the need of having horizontal experimental setups for state-of-the-art PID tuning for downhole RPM. The settling time of irregular RPM for horizontal setup is found to be lower than the vertical configuration due to multiple contact points and increased friction coefficient.

Genes coding for enzymes of the denitrification pathway appear randomly distributed among isolates of the ancestral genus Thermus, but only in few strains of the species T. thermophilus the pathway has been studied to a certain detail. Here, we review the enzymes involved in this pathway present in T. thermophilus NAR1, a strain extensively employed as a model for nitrate respiration, on the light of its full sequence recently assembled through a combination of PacBio and Illumina technologies in order to counteract the systematic errors introduced by the former technique. The genome of this strain is divided in four replicons, a chromosome of 2,021,843 pb, two megaplasmids of 370,865 and 77,135 bp and a small plasmid of 9,799 pb. Nitrate respiration is encoded in the largest megaplasmid, pTTHNP4, within a region that includes operons for O2 and nitrate sensory systems, a nitrate reductase, nitrate and nitrite transporters and a nitrate specific NADH dehydrogenase, in addition to multiple insertion sequences (IS), suggesting its mobility-prone nature. Despite nitrite is the final product of nitrate respiration in this strain, the megaplasmid encodes two putative nitrite reductases of the cd1 and Cu-containing types, apparently inactivated by IS. No nitric oxide reductase genes have been found within this region, although the NorR sensory gene, needed for its expression, is found near the inactive nitrite respiration system. These data clearly support that partial denitrification in this strain is the consequence of recent deletions and IS insertions in genes involved in nitrite respiration. Based on these data, the capability of this strain to transfer or acquire denitrification clusters by horizontal gene transfer is discussed.

In this study, a matched-mode autoregressive source depth estimation method (MMAR) based on autoregressive (AR) wavenumber estimation is proposed for a moving source in shallow water waveguides. The signal original frequency and the environmental parameters, namely, the sound speed profile and bottom properties are known as a prior knowledge. The mode wavenumbers are estimated by the AR modal wavenumber spectrum. On the basis of the mode wavenumber estimation, the mode amplitudes can be estimated by the wavenumber spectrum that is obtained by generalized Hankel transform. The source depth estimation is determined by the peak of source depth function wherein the data mode best matches the replica mode that is calculated using a propagation model. Compared with other methods of moving source depth estimation, the proposed method exhibits a better performance in source depth estimation under low signal-to-noise ratio or the small range span. The selection of horizontal line array depth is illustrated by simulation and normal mode theory in details.

Horizontal gene transfer (HGT) is the transmission of genes between organisms by other means than parental to offspring inheritance. While it is prevalent in prokaryotes, HGT is less frequent in eukaryotes and particularly in metazoan. Here, we propose Alienness, a taxonomy-aware web application that parses BLAST results against public libraries to rapidly identify candidate HGT in any genome of interest. Alienness takes as input the result of a BLAST of a whole proteome of interest against any NCBI protein library. The user defines recipient (e.g. metazoan) and donor (e.g. bacteria, fungi) branches of interest in the NCBI taxonomy. Based on the best BLAST E-values of candidate donor and recipient taxa, Alienness calculates an Alien Index (AI) for each query protein. An AI >0 indicates a better hit to candidate donor than recipient taxa and a possible HGT. Higher AI represent higher gap of E-values between candidate donor and recipient and a more likely HGT. We confirmed the accuracy of Alienness on phylogenetically confirmed HGT of non-metazoan origin in plant-parasitic nematodes. Alienness scans whole proteomes to rapidly identify possible HGT in any species of interest and thus fosters exploration of HGT more easily and largely across the tree of life.

Background: As a relatively high number of ST-segment elevation myocardial infarction (STEMI) patients develop major adverse cardiovascular events (MACE) following percutaneous coronary intervention (PCI), our aim was to determine the significance, and possible predictive value of QRS complex width and ST-segment elevation. Methods: Our patient sample included 200 PCI-treated STEMI patients, which were divided into two groups, based on the duration of symptoms: (I) less than 6 hours, and (II) 6-12 hours. For every patient, ECG was performed at 6 different time points. Long-term follow-up lasted 6 years from the STEMI onset. Statistical analysis was performed. Results: The mean age was 60.6±11.39 years, and 142 were male. Wider QRS complex, more pronounced ST-segment elevation, and more frequently absent ST-segment resolution were more common in the second group. Presentation of MACE was more frequent in this group. An increase of pre-PCI QRS complex width by 1 msec increases the risk of 6-year MACE by 3%, and an increase in pre-PCI ST-segment elevation by 1mm increases the risk of 6-year MACE by 3.26 times. Conclusion: To the best of our understanding, this study represents a pioneer research that utilized these ECG elements in the context of predicting a 6-year MACE. A wider QRS complex and a more pronounced ST-segment elevation were associated with longer total ischemic time. More research is needed to confirm these findings.

A recent study by the Wall Street Journal reveals that the hydrofractured horizontal wells in shales have been producing less than forecasted by the industry with the empirical hyperbolic decline curve analysis (DCA). As an alternative to DCA, we introduce a simple, fast and accurate method of estimating ultimate recovery (EUR) in oil shales. We adopt a physics-based scaling approach to analyze oil rates and ultimate recovery from 14,888 active horizontal oil wells in the Bakken shale. To predict EUR, we collapse production records from individual horizontal shale oil wells onto two segments of a master curve: (1) We find that cumulative oil production from 4,845 wells is still growing linearly with the square root of time; and (2) 6,401 wells are already in exponential decline after approximately seven years on production. In addition, 2,363 wells have discontinuous production records, because of refracturing or changes in downhole flowing pressure, and are matched with a linear combination of scaling curves superposed in time. The remaining 1,279 new wells with less than 12 months on production have too few production records to allow for robust matches. These wells are scaled with the slopes of other comparable wells in the square-root-of-time flow regime. In the end, we predict that total ultimate recovery from all existing horizontal wells in Bakken will be some 4.5 billion barrels of oil. We also find that wells completed in the Middle Bakken formation, in general, produce more oil than those completed in the Upper Three Forks formation. The newly completed longer wells with larger hydrofractures have higher initial production rates, but they decline faster and have EURs similar to the cheaper old wells. There is little correlation among EUR, lateral length, and the number and size of hydrofractures. Therefore, technology may not help much in boosting production of new wells completed in the poor immature areas along the edges of the Williston Basin. Operators and policy-makers may use our findings to optimize the possible futures of the Bakken shale and other plays. More importantly, petroleum industry may adopt our physics-based method as an alternative to the overly-optimistic hyperbolic DCA that yields an "illusory picture" of shale oil resources.

Capsizing accidents are regarded as marine accidents with a high rate of casualties per accident. Approximately 89% of all such accidents occur in small ships (vessels with gross tonnage less than 10 tons). Stability calculations are critical for assessing the risk of capsizing incidents and evaluating a ship's seaworthiness. Despite the high frequency of capsizing accidents involving small ships, they are generally exempt from adhering to stability regulations, thus remaining systemically exposed to the risk of capsizing. Moreover, the absence of essential design documents complicates direct ship stability calculations. This study utilizes hull form feature data—obtained from the general arrangement of small ships—as input for a deep learning model. The model is structured as a multilayer neural network and aims to infer hydrostatic curves, which is required data for stability calculations.

Due to the complex and variable anatomy of the left atrial appendage, percutaneous left atrial appendage closure (LAAC) can be challenging. In this study, we investigated the impact of fusion imaging (FI) on the LAAC learning curve of 2 interventionalists. The first interventionalist (IC 1) was initially trained without FI and continued his training with FI. The second interventionalist (IC 2) performed all procedures with FI. We compared the first 36 procedures without FI of IC 1 (group 1) with his next 36 interventions with FI (group 2). Furthermore, group 1 was compared to 36 procedures of IC 2 who directly started his training with FI (group 3). Group 1 demonstrated that the learning curve without FI has a flat course with weak correlations for fluoroscopy time, contrast volume, and procedure time, but not for dose area product. Group 2 with FI showed improvement with a steep course and strong correlations for all 4 parameters. In group 3 we also saw a steep progression with strong correlations. Furthermore, the mean measurements of the procedural parameters in the groups with FI decreased significantly as indicator for procedural efficacy. We demonstrated that FI may improve the learning curve of experienced and non-experienced ICs.

The accelerated pace with which new diagnostic possibilities are produced and the budget re-strictions of the healthcare sector require that the decision-making process of acquiring new technologies becomes systematic in nature. There are some methodologies such as the Health Technology Assessment (HTA) that encompasses technological domains, clinical effectiveness, patient safety, organizational and financial aspects, among others. However, these methods do not contemplate the learning curve (LC) which is a differential factor in operator-dependent technologies. An assessment model was conceived based on the assessment domains of the AdHopHTA project with the addition of LC. The model was validated and calibrated through System Dynamics (SD) and using as case study the assessment of Point-of-care Ultrasound (POCUS) equipment in dengue screening. The model helped identify the influence of the LC and patient demand on the income and costs for the healthcare system regarding dengue screening as well as the cost-benefit indicator. The control charts LC-CUSUM and CUSUM are graphic tools to intuitively assess the learning curve which can be used for real-time monitoring once students reach a certain skill level.

Climate change has become a major concern for developing countries given the risk that it posses on energy and food independence, and on general productivity. Despite having an energy system with low carbon intensity when compared to other Latin American countries, Colombia is already facing climate change impacts and requires urgent efforts to mitigate them. As a developing country, the challenge is bigger as policies for economic growth should be in line with the global commitment of reducing greenhouse gas emissions. With the aim of contributing to the design of climate policies, this study assesses the impact of economic development on the environment by examining the validity of the Environmental Kuznets Curve hypothesis for Colombia. Statistically validated and stable autoregressive distributed lag models are estimated for three different environmental indicators: carbon dioxide emissions, methane emissions, and ecological footprint. Moreover, the effects of other variables such as urbanization, foreign direct investment, value added of agricultural and industrial sectors, and energy use are analyzed with dynamic simulations. Empirical evidence supports a long-run equilibrium relationship among investigated variables and the existence of an inverted U-shaped EKC relationship between Gross Domestic Product (GDP) and methane emissions, and GDP and ecological footprint. Shifting to renewable energy sources and leveraging the use of cleaner technologies in agricultural and industrial sectors are found to be key for economic growth without harming the environment.

The importance of vertical jump in sport fields and rehabilitation is widely recognized. Furthermore, Force-Time variables of vertical jump are factors affecting jumping height. Exclusive review of each of this variables, in eccentric and concentric phases, can lead to a specific focus on them during jumping exercises. So, the aims of his study were to a) reviewing the relationship between force-time curve variables of eccentric and concentric phases with jump height and b) description of this variables in Iran national youth volleyball players society. This is an observational study. 12 elite volleyball player (Male, Iran national youth volleyball players, 17±0.7 years) have participated in this study. Correlation between Force-Time variables - included peak force (PF), relative peak force (RPP), peak power (PP), average power (AP), relative peak power (RPP), and Modified Reactive Strength Index (MRSI) - in eccentric and concentric phases and ultimate jump height has been studied. Results showed that the average power (r=0.7) and relative peak force (r=0.75) of concentric phase and MRSI (r=0.83) have significant correlation with ultimate jump height (JH). Relative peak power and average power of concentric phase can massively effect Jump Height in sports like volleyball, which vertical jump is an integral part of them. Focus on both of these factors, which has been studied in this research, in training programs, can improve athlete jump performance significantly.

This research explores the application of Support Vector Machine (SVM) and Digital Surface Models (DSM) derived from Unmanned Aerial Vehicle (UAV) data for a vertical-horizontal classification of mangrove ecosystems in Tongke-tongke and Samataring Village. The study focuses on integrating high-resolution DSM subtracted from Digital Terrain Models (DTM) to classify mangrove vegetation into sixteen distinct vertical-horizontal classes based on vegetation type and elevation. The analysis revealed that older mangroves, particularly those within the 25-35 meters elevation range, dominate the landscape, accounting for 43.40% of the total classified area. This dominance suggests a mature and ecologically stable mangrove ecosystem, which is crucial for biodiversity conservation and carbon storage. The study demonstrates the effectiveness of SVM and UAV technologies in providing detailed and accurate ecological assessments of mangrove forests. The classification results contribute valuable insights into the structural diversity and health of mangrove ecosystems, facilitating targeted conservation and management strategies. Additionally, the research highlights the utility of advanced remote sensing and machine learning techniques in enhancing the precision of environmental monitoring and the assessment of carbon sequestration capabilities within mangrove ecosystems. The findings underscore the potential of UAV-based remote sensing for ecological studies, offering a replicable method for similar assessments in other regions, thereby supporting global environmental management and climate action initiatives.

A linear stability analysis of the parallel uniform flow in a horizontal channel with open upper boundary is carried out. The lower boundary is considered as an impermeable isothermal wall, while the open upper boundary is subject to a uniform heat flux and it is exposed to an external horizontal fluid stream driving the flow. An eigenvalue problem is obtained for the two-dimensional transverse modes of perturbation. The study of the analytical dispersion relation leads to the conditions for the onset of convective instability as well as to the determination of the parametric threshold for the transition to absolute instability. The results are generalised to the case of three-dimensional perturbations.

Myocilin is an enigmatic glaucoma-associated glycoprotein whose biological role remains incompletely understood. To gain novel insight into its normal function, we used transposon-mediated transgenesis to generate the first zebrafish line stably overexpressing myocilin [Tg(actb1:myoc-2A-mCherry)]. qPCR showed an approximately four-fold increased myocilin expression in transgenic zebrafish embryos (144 hpf). Adult (13 months old) transgenic animals displayed variable and age-dependent ocular anterior segment alterations. Almost 60% of two-years old male, but not female, transgenic zebrafish developed enlarged eyes with severe asymmetrical and variable abnormalities in the anterior segment, characterized by corneal limbus hypertrophy, and thickening of the cornea, iris, annular ligament and lens capsule. The most severe phenotype presented small or absent ocular anterior chamber and pupils, due to iris overgrowth along with dysplastic retinal growth and optic nerve hypertrophy. Immunohistochemistry revealed increased presence of myocilin in most altered ocular tissues of adult transgenic animals, as well as signs of retinal gliosis, and expanded ganglion cells and nerve fibers. The preliminary results indicate that these cells contributed to retinal dysplasia. Visual impairment was demonstrated in all old male transgenic zebrafish. Transcriptomic analysis of the abnormal transgenic eyes identified disrupted expression of genes involved in lens, muscular and extracellular matrix activities, among other processes. In summary, the developed transgenic zebrafish provides a new tool to investigate this puzzling protein and provides evidence for the role of zebrafish myocilin in ocular anterior segment and retinal biology, through the influence of extracellular matrix organization and cellular proliferation.

Background: High coronary thrombus burden has been associated with unfavorable outcomes in patients with ST-segment elevation myocardial infarction (STEMI), the optimal management of which has not yet to be established. Methods: We evaluated the safety and efficacy of adjunctive catheter-directed thrombolysis (CDT) during primary percutaneous coronary intervention (PCI) in patients with STEMI and high thrombus burden. Results: Among the 1,849 consecutive patients with STEMI, 263 had high thrombus burden. Moreover, 41 patients received intracoronary infusion of tissue plasminogen activator during primary PCI (CDT group), whereas 222 did not receive (non-CDT group). No significant differences in bleeding complications and in-hospital and long-term mortalities were observed (9.8% vs. 7.2%, p=0.53; 7.3% vs. 2.3%, p=0.11; and 12.6% vs. 17.5%, p=0.84, CDT vs. non-CDT). In patients who underwent antecedent aspiration thrombectomy during PCI (75.6%; CDT group and 87.4%; non-CDT group), thrombolysis in myocardial infarction grade 2 or 3 flow rate after thrombectomy was significantly lower in the CDT group than in the non-CDT group (32.2% vs. 61.0%, p&lt;0.01). However, the final rates improved considerably without significant difference (90.3% vs. 97.4%, p=0.14). Conclusions: For STEMI patients with high thrombus burden, adjunctive CDT is safe and effective for improving coronary flow. CDT resulted in favorable coronary flow even after unsatisfactory aspiration thrombectomy.

The horizontal flatbed electrophoresis system has been used for the electrophoresis of protein samples and is often preferred for a two-dimensional polyacrylamide gel electrophoresis. In currently available equipment, cathode and anode electrodes were placed on top of a gel at each end. An electric field entered from the top of a gel, and its strength was relatively weaker in the bottom part of the gel. Such configuration caused migrating protein bands to lie down forward in the migrating direction. New electrodes, i.e., the clamp-shaped and the double-deck electrodes, were developed to simultaneously apply an electric field from the top and bottom of a gel. Electrophoretic separation with these electrodes made protein bands more focused and improved protein band resolutions. When the FIGE technique was tested together with new electrodes, protein bands were aligned nearly vertically and showed the best electrophoretic resolutions.

As development progresses, when the bottom hole flowing pressure or formation pressure is less than the saturation pressure of crude oil in the reservoir, oil and gas two-phase seepage occurs in the reservoir. Due to the characteristics of oil and gas two-phase seepage, after the oil and gas two-phase seepage occurs in the reservoir, the well production will be reduced, or even greatly reduced. Therefore, how to predict the horizontal well capacity better in this case is an important problem that needs to be solved urgently. In this paper, the method and process of establishing the transient calculation model of two-phase flow in horizontal wells are introduced in detail from three aspects: fluid physical properties, reservoir oil-gas two-phase seepage, and the coupling model of Inflow Performance and Flow in Wellbore. The model is more reliable through the verification of production data from five wells in two oilfields.