In geotechnical engineering applications, it is very important to obtain the undrained shear strength of remolded soils accurately and reliably. This study aims to obtain a trustworthy solution to determine the undrained shear strength of remolded clay mixtures using Atterberg limit test results in various states of consistency. An experimental study was carried out involving a wide range of clay mixtures of varying plasticity and geological origin. In the analyses, the variation of the remolded undrained shear strength depending on the cone penetration depth, water content, flow index, liquidity index and log liquidity index were investigated. In the study, the highest undrained shear strength of 100% Na-montmorillonite (NaM) was obtained at 171.89 kPa at 56.60% water content, while the lowest undrained shear strength was obtained for 100% Sepiolite (S), 9.28 kPa at 31.65% water content. The results of this study revealed that the shear strength is significantly affected by soil conditions, rather than dominant clay mineral. Besides, it was observed that the undrained shear strength at the plastic limit was approximately 30-35 times greater than that at liquid limit. The equations of liquid limit-flow index and plasticity index- flow index were proposed. It was concluded that the interdependence between undrained shear strength, liquidity index, log liquidity index, and flow index is not unique due to the different physical and chemical properties of clays.

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

To enhance pomegranate production on marginal gravelly lands, our study evaluated standardized planting techniques in an 8-year-old orchard. We employed trenching, wider pit excavation, pit digging, and auger digs with dimensions of 1 and 2 meters. Utilizing native soil from barren land, with or without spent wash, and mixing it with black soil up to 1 meter deep, we assessed growth parameters, leaf nutrients, and fruit yield. The trench and wider pit methods outperformed others, yielding greater above-ground biomass (>7.03 t tree-1), root biomass (2.5 t tree-1), and cross-sectional area (3.3 m² tree-1). Additionally, trench planting enhanced leaf phosphorus (0.28%) and potassium (1.8%) levels, fruit juice content (48.5%), total soluble solids (16.05°), and fruit yield (>9.3 t ha-1). The trench method also fostered longer roots at 90–150 cm radial distance and deeper roots at 40–60 cm depth. In summary, the trench and wider pit methods, combined with a soil mixture, are recommended for sustainable, high-quality fruit production in shallow gravelly terrains, thereby improving food security and the livelihoods of farmers in arid regions.

Ectopic expression of the MYB transcription factor of AmROSEA1 from Antirrhinum majus has been reported to change anthocyanin and other metabolites in several species. In this study, we found that overexpression of AmRosea1 significantly improved the tolerance of transgenic rice to drought and salinity stress. Transcriptome analysis revealed that a considerable amount of stress-related genes were affected by exogenous AmRosea1 during both drought and salinity stress treatments. These affected genes are involved in stress signal transduction, the hormone signal pathway, ion homeostasis and the enzymes that remove peroxides. This work suggests that the AmRosea1 gene is a potential candidate for genetic engineering of crops.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

Tissue engineered heart valves can grow, repair, and remodel after implantation, presenting a more favorable long-term solution compared to mechanical and porcine valves. Achieving functional engineered valve tissue requires the maturation of human cells seeded onto valve scaffolds under favorable growth conditions in bioreactors. The mechanical stress and strain on developing valve tissue caused by different pressure and flow conditions in bioreactors are currently unknown. The aim of this study is to quantify the wall shear stress (WSS) magnitude in heart valve prostheses under different valve geometries and bioreactor flow rates. To achieve this, the study used fluid-structure interaction simulations to obtain the valve's opening geometries during the systolic phase. These geometries were then used in computational fluid dynamics simulations with refined near-wall mesh elements and ranges of prescribed inlet flow rates. The data obtained included histograms and regression curves that characterized the distribution, peak, and median WSS for various flow rates and opening configurations. The study also found that the upper region of the valve near the commissures experienced higher WSS magnitudes than the rest of the valve.

The entropy models have been recently adopted in many studies to evaluate the distribution of the shear stress in circular channels. However, the uncertainty in their predictions and their reliability remains an open question. We present a novel method to evaluate the uncertainty of four popular entropy models, including Shannon, Shannon-Power Low (PL), Tsallis, and Renyi, in shear stress estimation in circular channels. The Bayesian Monte-Carlo (BMC) uncertainty method is simplified considering a 95% Confidence Bound (CB). We developed a new statistic index called as FREE_opt-based OCB (FOCB) using the statistical indices Forecasting Range of Error Estimation (FREE) and the percentage of observed data in the CB (N_in), which integrates their combined effect. The Shannon and Shannon PL entropies had close values of the FOCB equal to 8.781 and 9.808, respectively, had the highest certainty in the calculation of shear stress values in circular channels followed by traditional uniform flow shear stress and Tsallis models with close values of 14.491 and 14.895, respectively. However, Renyi entropy with much higher values of FOCB equal to 57.726 has less certainty in the estimation of shear stress than other models. Using the presented results in this study, the amount of confidence in entropy methods in the calculation of shear stress to design and implement different types of open channels and their stability is determined.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

The laser host materials undergo relatively small changes in their intrinsic properties due to various sources during an experiment. These sources are often related to temperature change or applied stress, which may cause change in optical properties of the material under study. Consequently, the crystal experiences an optical anisotropy, which may affect the final outcome of the experiments. One way to reduce probable noises is to predict the change in optical properties with respect to load. To predict the changing pattern of the refractive index in a crystal, one needs to know both the elastic and photoelastic constants of the material. In this study, we utilized density functional perturbation theory (DFPT) to extract the photoelastic tensor of Y$_2$SiO$_5$ and Eu-doped Y$_2$SiO$_5$ crystals. Using the photoelastic and elastic constants calculated, a Finite Element (FE) model was developed, which allowed us to apply load and then post-process the results. This methodology enabled us to observe the variation in refractive index ($n$), and consequently, the shift in the resonance frequency of the cavity. The results obtained were in agreement with experimental measurements, falling within a 3\% discrepancy across a temperature range spanning from cryogenic to room temperature. This correlation suggests the feasibility of using the current workflow as a predictive tool for evaluating variations in refractive indices over a specific interval.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Liquefaction risk assessment is critical for the safety and economics of structures. As the soil strata of Ramsar area in north Iran is mostly composed of poorly graded clean sand and the ground water table is found at shallow depths, it is highly susceptible to liquefaction. In this study, a series of isotropic and anisotropic consolidated undrained triaxial tests are performed on reconstituted specimens of Ramsar sand to identify the liquefaction potential of the area. The specimens are consolidated isotropically to simulate the level ground condition, and anisotropically to simulate the soil condition on a slope and/ or under a structure. The various states of soil behavior are studied by preparing specimens at different initial relative densities and applying different levels of effective stress. The critical state soil mechanics approach for identifying the liquefaction susceptibility is adopted and the observed phenomena are further explained in relation to the micro-mechanical behavior. As only four among the 27 conducted tests did not exhibit liquefactive behavior, Ramsar sand can be qualified as strongly susceptible to liquefaction. Furthermore, it is observed that the pore pressure ratio is a good indication of the liquefaction susceptibility

Background: The modified Duke index derived from coronary computed tomography angiography (CCTA) was designed to predict cardiovascular outcomes based on the severity of coronary ste-nosis. However, it does not take into consideration the presence or severity of peri-coronary in-flammation. The peri-coronary fat attenuation index (FAI) is a novel imaging marker determined by CCTA which reflects the degree of inflammation in the coronary tree in patients with coronary artery disease. Purpose: To assess the association between the modified Duke index assessed by CCTA, cardiovascular risk factors and peri-coronary inflammation in the coronary arteries of pa-tients with coronary artery disease. Methods: One hundred seventy-two patients who underwent CCTA for typical angina were assigned into two groups based on the modified Duke index: group 1 – patients with low index ≤ 3 (n=107) and group 2 – patients with high index > 3 (n=65). Demo-graphic, clinical and CCTA data were collected for all patients, and FAI analysis of coronary in-flammation was performed. Results: Patients with increased values of the modified Duke index were significantly older compared to those with a low index (61.83 ± 9.89 vs. 64.78 ± 8.9; p = 0.002). No differences were found between the two groups in terms of gender distribution, hypertension, hypercholesterolemia or smoking history (all p > 0.5). The FAI score was significantly higher in patients from group 2, who presented a significantly higher score of inflammation compared to the patients in group 1, especially at the level of the right coronary artery (FAI score 20.85 ± 15.80 vs. 14.61 ± 16.66; p = 0.01 for the right coronary artery, 13.85 ± 8.04 vs. 10.91 ± 6.5; p = 0.01 for the circumflex artery, and 13.26 ±10.18 vs. 11.37 ± 8.84; p = 0.2 for the left anterior descending artery). CaRi-Heart® analysis identified a significantly higher risk of future events among patients with a high modified Duke index (34.84 % ± 25.86 % versus 16.87 % ± 15.80 %; p

Blood image intensity has been used to detect erythrocyte sedimentation rate (ESR). However, it does not give an information on biophysical properties of blood sample under continuous ESR. In this study, three physical properties, including, τ₀, ESR_τ, and AI_I, are suggested to quantify mechanical variations of blood under continuous ESR. To demonstrate the proposed method, blood sample is loaded into a driving syringe. The blood flow rate is set in a periodic on–off pattern. Blood sample is then supplied into a capillary chip, and microscopic blood images are captured at specific intervals. Blood shear stress is quantified from the interface of blood stream in the coflowing channel. Both τ₀ and ESR_τ are then obtained by analyzing the blood shear stress. Simultaneously, the AI_I is evaluated by analyzing the image intensity of blood flow. According to the experimental results, the τ₀ exhibits consistent trends with respect to hematocrit as well as diluent. The ESR_τ and AI_I showed a reciprocal relationship each other. Three suggested properties represented substantial differences for suspended blood samples (i.e., hardened red blood cells, different concentration of dextran solution and fibrinogen). In conclusion, the present method can detect variations of blood sample under continuous ESR effectively.

The research carried out concerned the laboratory assessment of the applicability of the Crop Water Stress Index (CWSI) as a practical tool for assessing the risk of desiccation for selected wetland habitats: transition mires and quaking bogs as well as alkaline fens. The analysis was carried out on 3 soil samples with a vegetation cover (with the dimensions of 40×40×30 cm) collected during the full vegetation season for each mentioned habitat, with a characteristic species composition. Experimental research was carried out between 17^th May 2018 and 19^th June 2018. Thermal, RGB and multispectral images, chlorophyll content, volumetric soil moisture, air temperature and relative humidity measurements were taken for each sample every two days. The obtained results clearly indicate the dependence between CWSI and plant condition parameters in the first phase of desiccation. At the same time, as a result of the observations taken, thresholds have been set, indicating different desiccation phases.

Abstract: The VSI represents a significant advancement in the assessment of gastrointestinal-specific anxiety among patients with Irritable Bowel Syndrome (IBS) and other Chronic Inflammatory Bowel Diseases (IBD). However, an Italian version of the instrument is not yet available for the reference population. This study utilized a national sample of 500 individuals, including healthy controls and patients with Ulcerative Colitis and Crohn's Disease, to test the validity and reliability of the Italian VSI. Using back-translation methodology to ensure translation fidelity, the research applied a questionnaire and the VSI through an online format to 500 participants. Data analysis revealed that the Italian VSI had excellent psychometric properties, demonstrating high internal consistency (Cronbach’s α = 0.95) and construct validity. The scale proved sensitive in detecting significant differences in visceral sensitivity among groups, highlighting its utility as a clinical and research assessment tool. Specifically, the Italian VSI exhibited a unidimensional factorial structure and maintained a strong correlation with other measures of anxiety and the severity of gastrointestinal symptoms, confirming its role in enhancing the understanding and management of IBS and IBD in Italy.

This study investigates the Hagen–Poiseuille pipe flow of viscoplastic fluids, focusing on analytical predictions of concrete pumping using the shear-stress-dependent parabolic model. Research highlights encompass solving the steady laminar pipe flow for viscoplastic fluids described by the parabolic model, extending analytical studies to a nonlinear rheological model with easily accessible experimental parameters, presenting detailed results for the two-fluid parabolic model, and introducing computational apps implementing theoretical findings. The parabolic model outperforms linear models, such as the Bingham model, in accuracy by accounting for the nonlinearity in the shear stress and shear rate relations. The influence of rheological parameters on these relations is analyzed, and their versatility is demonstrated by a Wolfram Mathematica-based application program. This approach is adaptable for other models with shear stress as the independent variable, offering valuable insights into viscoplastic fluid flows.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

So that the levels of water stress are not harmful to the development of the crop and affect its productivity, its detection and monitoring are necessary, and it can occur in different ways. One of them is through the Crop Water Stress Index (CWSI). This index quantifies water stress through the normalization of leaf temperature between the maximum and minimum plant temperatures as a function of evaporation conditions. The responses of a low-cost infrared (IR) sensor were crossed with image processing through segmentation by the Excess Green model to develop a water stress detection system using CWSI. A soil/plant temperature map was generated through a point-to-point scan of the IR sensor. And when it overlaid with a segmented image of the experimental area, only points identified as plants had their temperature values maintained. The Non-Water-Stressed Baseline (NWSB) equation was parameterized for the same conditions of the experiment and external environmental. The experimental area was divided into three different treatments, maintained under stable water conditions throughout the experiment and the system was able to identify stably different stress values between treatments. Although the relationship between crop and environment affected the results, this work showed that using an irrigation system based on CWSI is possible.

Annually, the oak forests of the Zagros Mountain chains, in western Iran and northeastern Iraq, face recurring challenges posed by forest fires, particularly in the Kurdo-Zagrosian forests situated in western Iran and northeastern Iraq. Assessing fire susceptibility relies significantly on vegetation condition. Integrating in situ data, Remote Sensing (RS) data, alongside the integration of Geographical Information Systems (GIS), presents a cost-effective and precise approach to capturing environmental conditions before, during, and after fire events, minimizing the need for extensive fieldwork. This study refines and applies the Zagros Grass Index (ZGI), a local vegetation index tailored to discern between grass-covered surfaces from tree canopies in Zagros forests, identifying the grass masses as the most flammable fuel type. Utilizing Moderate Resolution Imaging Spectroradiometer (MODIS) Normalized Difference Vegetation Index (NDVI) product as input, from 2013 to 2022, the ZGI aims to mitigate the influence of tree canopies, isolating NDVI values solely attributable to grass cover. By incorporating phenological characteristics of forest trees and grass species, the ZGI outperforms NDVI in mapping grass-covered areas that are crucial for fire susceptibility assessment in the study region. Results demonstrate a strong overlap between ZGI-based maps and recorded fire occurrences, validating the efficacy of the index in fire susceptibility estimation.

The paper introduces a valuable new description of fatigue strength in relation to material properties and thus a new perspective on the overall understanding of the fatigue process. Namely, a relation between the endurance limits and the accompanying values of the critical resolved shear stress (CRSS) for various metallic materials has been discovered by means of a multiscale approach for fatigue simulation. Based on the uniqueness of the relation, there is a strong indication that it is feasible to relate the endurance limit to the CRSS, and not to the ultimate strength as often done in the past.

Managing a portfolio whose value closely tracks an index by trading only in a subset of the index constituents involves an NP-hard optimisation problem. In the prior literature, it has been suggested to solve this problem using sequential Monte Carlo (SMC, a.k.a. particle filter) methods. However, this literature does not take transaction costs into account, although transaction costs are the primary motivation for attempting to replicate the index by trading in a subset, rather than the full set of index constituents. This paper extends the SMC approach to index tracking to allow for proportional transaction costs and implements this extended method on empirical data for a variety stock indices. In addition to providing a more practically useful tracking strategy by allowing for transaction costs, we find that including a penalty for transaction costs in the optimisation objective can actually lead to better tracking performance.

Plants exhibit the capacity for adaptation through their metabolic processes to various changes in environmental conditions. Investigating these adaptations in current and future climatic scenarios is of great importance for ensuring productive agricultural crops. This adaptative potential is commonly employed as an indicator of genotypes with higher potential in breeding programs. However, the complexity and interaction of plant metabolic parameters pose a challenge to selection strategies. In this context, the aim of this study was to explore phenotypic plasticity within the germplasm of Hybrid Timor coffee. Additionally, we assessed the utility of the Phenotypic Plasticity Index (MVPi) as a promising tool to predict genotype performance across diverse climatic conditions. To achieve this, we evaluated the performance of seven accessions from the Hybrid Timor germplasm in comparison to the Rubi and IPR 100 cultivars, known for their susceptibility and resistance to drought, respectively. The experiment was conducted at greenhouse conditions, with two treatments: a control scenario, maintaining soil moisture near its maximum water-holding capacity, and a water deficit scenario involving irrigation cessation followed by rehydration. Data encompassing physiological, biochemical, and growth aspects were collected during three distinct stages: pre-application of water deficit, its imposition, and subsequent rehydration. Furthermore, field evaluations of the productivity of the same genotypes were carried out over two consecutive seasons. Based on physiological and biochemical assessments, the MVPi was computed, employing Euclidean distance between principal component multivariate analysis scores. Subsequently, this index was correlated with growth and productivity data through linear regressions. Our findings reveal that the more plastic genotypes, capable of significantly altering physiological and biochemical parameters in response to environmental stimuli, exhibited reduced biomass loss in both aerial and root parts, consequently positively influencing their productivity. Enhanced plasticity was particularly prominent in accessions from the MG Germplasm Collection: MG 311 - Hybrid Timor UFV 428-02, MG 270 - Hybrid Timor UFV 377-21, and MG 279 - Hybrid Timor UFV 376-31, alongside the Rubi MG 1192 cultivar. The MVPi emerged as a valuable instrument to assess genotype adaptability and predict their performance under varying climatic scenarios.

Climate change is challenging the agricultural sector worldwide. The pressure exerted by the altered thermal conditions drives the zonal shift for various cultivations. This study presents the multiyear analysis of the Growing Degree Days (GDD) index over the Northern Mediterranean Basin (NMB), focused on the high-value vine cultivation derived from the E-OBS dataset. To handle this extensive environmental dataset, R-language scripts and packages were applied, along with the capabilities of the GIS software. The investigated time period spans from 1969 to 2018, and the performed analysis indicates a broad shift/expansion in areas of GDD exceeding 2000 heat units. The extracted results specify the viticultural areas where the GDD index surpasses the suitable values for vine cultivation, owing to the increase of the thermal stress risk. In addition to mapping areas with GDD ≥ 2000, spatial calculations of the surface of areas meeting this criterion per country in the study area were made. In the northern parts of the NMB, the rise of the GDD index values indicates the establishment of vine plantations in the future.

Floods are a common natural disaster whose severity in terms of duration, water resource volume, peak and accumulated rainfall-based damage are likely to differ significantly for different geographical regions. In this paper, we first propose a novel hourly flood index (SWRI24−hr−S), derived from normalising the existing 24-hourly water resources index (WRI24−hr−S) in literature, to monitor flash flood risks on an hourly scale. The proposed SWRI24−hr−S is adopted to identify a flood situation and derive its characteristics, such as the duration (D), volume (V) and peak (Q). The comprehensive result analysis establishes the practical utility of SWRI24−hr−S in identifying flood situations at seven study sites in Fiji between 2014 and 2018 and deriving their characteristics (i.e., D, V, and Q). Secondly, this study develops a vine copula-probabilistic risk analysis system that models the joint distribution of flood characteristics (i.e., D, V, and Q) to extract their joint exceedance probability for the seven study sites in Fiji, enabling probabilistic flood risk assessment. The vine copula approach, particularly suited to Fiji’s study sites, introduces a novel probabilistic framework for flood risk assessment. The results show moderate differences in the spatial patterns of joint exceedance probability of flood characteristics in different combination scenarios generated by the proposed vine copula approach. In the worst-case scenario, the probability of any flood event occurring where the flood volume, peak and duration are likely to exceed the 95th-quantile value (representing an extreme flood event) is found to be less than 5% for all study sites. The proposed hourly flood index and the vine copula approach can be feasible and cost-effective tools for flood risk monitoring and assessment. The methodologies proposed in this study can be applied to other data-scarce regions where only rainfall data is available, offering crucial information for flood risk monitoring, assessment, and the development of effective mitigation strategies.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

One of the most important subjects of hydraulic engineering is the reliable estimation of the transverse distribution in rectangular channel of bed and wall shear stresses. This study makes use of the Tsallis entropy, Genetic Programming (GP) and (ANFIS) methods to assess the shear stress distribution (SSD) in rectangular channel. To evaluate the results of the Tsallis entropy, GP and ANFIS models, laboratory observations were used in which shear stress was measured using an optimized Preston tube. This is then used to measure the SSD in various aspect ratios in the rectangular channel. To investigate the shear stress percentage, 10 data series with a total of 112 different data for were used. The results of the sensitivity analysis show that the most influential parameter for the SSD in smooth rectangular channel is the dimensionless parameter B/H, Where the transverse co-ordinate is B, and the flow depth is H. With the parameters (b/B), (B/H) for the bed and (z/H), (B/H) for the wall as inputs, the modeling of the GP was better than the other one. Based on the analysis, it can be concluded that the use of GP and ANFIS algorithms is more effective in estimating shear stress in smooth rectangular channels than the Tsallis entropy-based equations.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

Recent analyses of cosmic microwave background surveys have revealed hints that there may be a non-trivial running of the running of the spectral index. If future experiments were to confirm these hints, it would prove a powerful discriminator of inflationary models, ruling out simple single field models. We discuss how isocurvature perturbations in multi-field models can be invoked to generate large runnings in a non-standard hierarchy, and find that a minimal model capable of practically realising this would be a two-field model with a non-canonical kinetic structure. We also consider alternative scenarios such as variable speed of light models and canonical quantum gravity effects and their implications for runnings of the spectral index.

In the paper the verification of forecasts of precipitation conditions measured by the standardized precipitation index SPI is presented. For the verification of categorical forecasts a contingency table was used. Standard verification measures were used for the SPI value forecast. The 30 day SPI moved every 10 days by 10 days was calculated in 2013-2015 from April to September on the basis of precipitation data from 35 meteorological stations in Poland. Predictions of the 30 day SPI were created in which precipitation was forecasted in the next 10 days (the SPI 10-day forecast) and 20 days (the SPI 20-day forecast). Both for the 10 and 20 days, the forecasts were skewed towards drier categories at the expense of wet categories. There was a good agreement between observed and 10-day forecast categories of precipitation. Less agreement is obtained for 20-day forecasts – these forecasts evidently “over-dry” the assessment of precipitation anomalies. The 10-day SPI value forecast accuracy is acceptable, whereas for the 20-day forecast is unsatisfactory. Both for the SPI categorical and the SPI value forecast, the 10-day SPI forecast is reliable and the 20-day forecast should be accepted with reservation and used with caution.

Aim: To investigate inflammation indices and erythropoietin (EPO) levels for their potential role in distinguishing polycythemia vera (PV) from secondary polycythemia (SP), and to compare different parameter combinations in terms of diagnostic accuracy. Methods: This retrospective cohort was created from patients assessed for polycythemia from January 2020 to December 2023. PV diagnosis was made according to the 2016 WHO criteria (n=145). Those who did not fulfill the criteria were defined as having SP (n=84). Results: NLR, PLR and SII were significantly higher in the PV group (p

This research aimed to investigate the relationship between climate policy uncertainty (CPU), clean energy (ENERGY), carbon emission allowance prices (CARBON), and Bitcoin returns (BTC) for the period from August 2012 to August 2022. The empirical analysis strategies utilized in this study included the Fourier Bootstrap ARDL long-term coefficient estimator, Fourier Granger Causality, and Fourier Toda Yamamoto Causality methods. Following the confirmation of cointegration among the variables, we observed a positive relationship between BTC and CARBON, a positive relationship between BTC and CPU, and a negative relationship between BTC and ENERGY. In terms of causal associations, we identified one-way causality running from CARBON to BTC, BTC to CPU, and BTC to the ENERGY variable. The study underscores the potential benefits and revenue opportunities for investors seeking diversified investment strategies in light of climate change concerns. Furthermore, it suggests actionable strategies for policymakers, such as implementing carbon taxes and educational campaigns, to foster a transition towards clean energy sources within the cryptocurrency mining sector and thereby mitigate environmental impacts.

This review aims to explore the intricate relationship between epigenetic mechanisms, stress, and affective disorders, focusing on how early life experiences and coping mechanisms contribute to susceptibility to mood disorders. Epigenetic factors play a crucial role in regulating gene expression without altering the DNA (deoxyribonucleic acid) sequence, and recent research has revealed associations between epigenetic changes and maladaptive responses to stress or psychiatric disorders. A scoping review of 33 studies employing the PRISMA-S (Preferred Reporting Items for Systematic Reviews and Meta-Analyses – Statement) guidelines investigates the role of stress-induced epigenetic mechanisms and coping strategies in affective disorders' occurrence, development, and progression. The analysis encompasses various stress factors, including childhood trauma, work-related stress, and dietary deficiencies, alongside epigenetic changes such as DNA methylation and altered gene expression. Findings indicate that specific stress-related genes frequently exhibit epigenetic changes associated with affective disorders. Moreover, the review examines coping mechanisms in patients with bipolar disorder and major depressive disorder, revealing mixed associations between coping strategies and symptom severity. While active coping is correlated with better outcomes, emotion-focused coping may exacerbate depressive or manic episodes. Overall, this review underscores the complex interplay between genetic predisposition, environmental stressors, coping mechanisms, and affective disorders. Understanding these interactions is essential for developing targeted interventions and personalized treatment strategies for individuals with mood disorders. However, further research is needed to elucidate specific genomic loci involved in affective disorders and the clinical implications of coping strategies in therapeutic settings.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

We explored how dietary behaviors (sucrose, fructose, sodium, and potassium consumption) and endured psychological stress in young adult males and females impact the vascular aging index (VAI) and CVD risk by mid-life. Data were obtained from the Coronary Artery Risk Development in Young Adults Study, an ongoing longitudinal study. Included participants (n=2,656) had un-dergone carotid artery ultrasound at year 20 allowing VAIs to be calculated. Demographics, di-etary data and depression scores were obtained at baseline and year 20. Regression analyses were used to assess the predictors of VAI. Cox regression analyses were conducted to assess the risk of CVD, stroke and all-cause mortality. Predictors of vascular aging were found to be sex-specific. In females, CES-D scores at baseline were positively associated with VAI (B-weight=0.063, p=0.015). In males, sodium intake at year 20 positively predicted VAI (B-weight=0.145, p=0.003) and potassium intake inversely predicted VAI (B-weight=-0.160, p<0.001). BMI significantly predicted CVD, stroke, and death. Fructose consumption at year 20 was a significant predictor of CVD risk while having high blood pressure at baseline was signif-icantly associated with stroke risk. Our findings support the promotion of nutrient- specific be-havior changes to prevent vascular aging in early adulthood and CVD risk in mid-life.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

The fetal splenic artery pulsatility index (PI) is a parameter that reflects fetal well-being and has been used as a predictor of adverse pregnancy outcomes. The aim of this study was to investigate the predictive value of splenic artery PI in GDM class A1 cases for NICU admission. In this prospective case controlled study, only sixty single pregnancy cases diagnosed with gestational diabetes mellitus class A1 were evaluated. Fetal splenic artery Doppler parameters Peak systolic velocity (PSV), Pulsatility index (PI), Resistivity index (RI) and End diastolic velocity (EDV) were measured in all cases. The rate of re-quirement of need of neanoatal intensive care unit was noted. In cases with need fetal intensive care, fetal splenic PI index was found to be statistically significantly lower than in healthy cases without it (0.94 ± 0.29 vs. 1.70 ± 0.53, respectively, p

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

The clinical relationship between diabetes and inflammation is well-established. Various branches of science independently have confirmed that disrupting oxidant-antioxidant equilibrium and elevated lipid peroxidation could be a potential mechanism for chronic kidney disease associated with Type 2 diabetes mellitus (T2DM). Under diabetic condition, hyperglycemia, especially inflammation, and increased reactive oxygen species generation are bidirectionally associated. Inflammation, oxidative stress and tissue damage are believed to have a role in the development of diabetes. Although the exact mechanism underlying the oxidative stress and its impact on diabetes progression remains uncertain, the hyperglycemia-inflammation-oxidative stress interaction clearly plays a significant role in onset and progression of vascular disease, kidney disease, hepatic injury, pancreas damage and, therefore holds promise as a therapeutic target. Evidence strongly indicates that the use of multiple antidiabetic medications therapy fails to achieve the normal range for glycated hemoglobin target, signifying treatment resistant diabetes. Antioxidants with polyphenols are considered useful as adjuvant therapy for their potential anti-inflammatory effect and antioxidant activity. We aimed to analyze the current major points reported in preclinical in vivo and clinical studies of antioxidants in the prevention or treatment of inflammation in T2DM. Then, we will share our speculative vision of the future diabetes clinical trials.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

The intracellular calcium dynamics in vascular endothelial cells (VECs) in response to wall shear stress (WSS) and/or adenosine triphosphate (ATP) have been commonly regarded as an important factor in regulating VEC function and behavior including proliferation, migration and apoptosis. However, the effects of time-varying ATP signals have been usually neglected in the past investigations in the field of VEC mechanobiology. In order to investigate the combined effects of WSS and dynamic ATP signals on the intracellular calcium dynamic in VECs, a Y-shaped microfluidic device, which can provide the cultured cells on the bottom of its mixing micro-channel with stimuli of WSS signal alone and different combinations of WSS and ATP signals in one single micro-channel, is proposed. Both numerical simulation and experimental studies verify the feasibility of its application. Cellular experimental results also suggest that a combination of WSS and ATP signals rather than a WSS signal alone might play a more significant role in VEC Ca²⁺ signal transduction induced by blood flow.

Properties of time domain parameters of the vibration signal have been extensively studied for the fault diagnosis of rolling element bearings (REB). Parameters like kurtosis and Envelope Harmonic-to-Noise Ratio are most widely applied in this field and some important progress has been made. However, since only one-sided information is contained in these parameters respectively, problems still exist in practice when the signals collected are of complicated structure and/or contaminated by strong background noises. A new parameter, named Shock pulse index (SPI), is proposed in this paper. It integrates the mutual advantage of both parameters above and can help effectively identify fault related impulse components under the interference of strong background noises, unrelated harmonic components and random impulses. The SPI optimizes the parameters of Maximum Correlated Kurtosis Deconvolution (MCKD), which is used to filter the signals under consideration. Finally, the interested transient information contained in the filtered signal can be highlighted through demodulation with Teager Energy Operator (TEO). Fault related impulse components can therefore be extracted accurately. Simulations and experiment analyses verify the effectiveness and correctness of the SPI.

Pregnancy is a complex biological process which is associated with significant metabolic and hemodynamic changes of the maternal body which allow a normal fetal growth. The inability to adapt to these changes can affect the cardiovascular health. During pregnancy, women may experience mood swings, anxiety and emotional ambivalence. These symptoms can lead to stress and have a negative impact on the mental well-being of expectant mothers. It is crucial to know the aspects that can influence the development of cardiovascular problems among pregnant women in order to manage these cases properly. The current narrative review explores and summarizes the evidence regarding the impact of stress and anxiety on cardiovascular health in pregnant women. Understanding the physiological adaptations that the body undergoes throughout pregnancy is crucial for educating and supporting individuals as well as healthcare professionals. This enables them to recognize any risk factors or pathological conditions that may exacerbate pregnant women's health. In order to reduce maternal morbidity and mortality from cardiovascular disease, a psychological and cardiovascular risk factor screening that is done either before or during pregnancy may be able to identify situations that call for particular medical and/or psychological therapies.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

This paper contains theoretical fundamentals of strut and tie models, used in unreinforced horizontal shear walls. Depending on support conditions and wall loading, we can distinguish models with discrete bars when point load is applied to the wall (type I model) or with continuous bars (type II model) when load is uniformly distributed at the wall boundary. The main part of this paper compares calculated results with the own tests on horizontal shear walls made of solid brick, silicate elements and autoclaved aerated concrete. The tests were performed in Poland. The model required some modifications due to specific load and static diagram.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Abstract: Doppler renal resistive index (RRI) has been used for several decades as a potential indi-cator for renal disease and progression. In recent years, RRI has emerged as a useful prognostic indicator for a range of co-morbidities in patients who are acutely unwell and as a potential marker for sub-clinical acute kidney injury (AKI) and post procedural AKI risk. Despite this, the clinical and theoretical determinants of RRI are poorly understood and remain contentious. Method: A narrative review of studies exploring the theoretical, experimental, and clinical evidence for factors affecting RRI. No date restrictions were set. Findings: Both experimental and clinical data confirm that RRI is markedly affected by a range of systemic and renal determinants and is influenced closely by the underlying risk factors and sys-temic vascular changes that lead to progressive renal damage. Discussion: This paper provides an overview of the key haemodynamic determinants of renal re-sistive index and aims to clarify their relative importance. With reference to a simplified theoretical model, evidence from experimental and clinical studies is reviewed. Pathophysiological factors and patient characteristics that influence RRI are explored to provide a better understanding of why RRI values change in the presence of common or complex pathologies. Conclusion: By gaining a better understanding of the complex systemic and renal factors that influ-ence RRI, ultrasound users will be better prepared to understand and interpret changes in RRI across a range of patient presentations.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

According to previous studies the median raphe region (MRR) is known to contribute significantly to social behavior. Beside serotonin, there are reports of a small population of dopaminergic neu-rons in this region. Dopamine is linked to reward and locomotion, but very little has been known about its role in the MRR. To address that, we first confirmed the presence of dopaminergic cells in the MRR of mice (immunohistochemistry, RT-PCR) and humans (RT-PCR). Next, we used chemogenetic technology in mice containing Cre enzyme under the promoter of the dopamine transporter (DAT). With the help of an adeno-associated virus, artificial receptors were expressed in the dopaminergic cells of the MRR (DAT-MRR). Four weeks later, extensive behavioral charac-terization started 30 minutes after the injection of the artificial ligand (Clozapine-N-Oxide). Stimu-lation of DAT-MRR decreased social interest without influencing aggression and with an increase in social discrimination. Additionally, inhibition of the same cells increased the friendly social be-havior during social interaction test. No behavioral changes were detected in anxiety, memory and locomotion. All in all, dopaminergic cells were present both in the mice and human MRR, and manipulation of dopaminergic neurons of the MRR elicited a specific social response.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

Study Objective: This study examined office workstation types’ impact on objective health-related metrics including stress, physical activity (PA), and sleep quality. We propose a sensor-based sleep quality index (SB-SQI) to fill a needed gap for objective sleep quality measurement over short timescales. Methods: We monitored 231 office workers using chest-worn sensors for 72 hours, yielding 11,736 hours of usable data from 163 participants (mean age 43.4, 56% women). SB-SQI was based on a validated algorithm estimating sleep-onset latency, total sleep time, and sleep efficiency, using the scoring method from the Pittsburg Sleep Quality Index (PSQI). We examined the relationships between SB-SQI, office workstation type (open-bench seating, cubicle, and private office), work-hours stress (standard deviation of heart rate variability), and after-work PA (relative duration of moderate-to-vigorous activity). Results: The sensor-derived poor-sleep ratio of the private office workers was higher than with other office workstation types (81% vs. 66.1%, p = 0.023). PSQI revealed a similar but insignificant trend with a lower effect-size. Among good-sleepers, open-bench seating workers had 22% (p = 0.018) less stress during work hours than others. A significant association between work-hours stress and after-work hours PA (r = 0.331, p = 0.000) was observed irrespective of office workstation type, with the highest PA level observed for open-bench seating workers. Conclusions: Office workstation type had a significant impact on work-hours stress, affecting PA after work hours, which influenced sleep quality. SB-SQI could be more sensitive than PSQI in determining the impact of office workstation types on sleep quality.

Fluid flow in human body is generally known to influence a variety of cellular behaviors. Different nanoparticle properties as well as cell type, interaction with other cells and cellular environments also show significant effect on nanoparticle uptake and drug efficacy. The aim of this study was to evaluate the effect of shear stress on cellular behaviors of biocompatible and biodegradable nanoparticles to cancer cells (A549 cell lines) in a biomimetic microfluidic system. We prepared a gelatin-oleic conjugate (GOC) as an amphiphilic biomaterial to prepare self-assembled gelatin-oleic nanoparticles (GON). Coumarin-6 and paclitaxel were used as the fluorescence marker and model drug, respectively, and were loaded into GONs by incubation (C-GONs; PTX-GONs). Additionally, we evaluated the cellular uptake of fluorescence labeled C-GONs and the drug efficacy of PTX-GONs. The cellular uptake of C-GONs by A549 cells in the absence of shear stress revealed that the mean fluorescence intensity was slightly decreased compared to that in the presence of shear stress. The results also indicated that negatively charged PTX-GONs had a lower cancer killing effect under dynamic conditions than that under static conditions. It also suggested that fluidic shear stress did not significantly affect drug uptake and efficiency in case of PTX-GONs. The cellular interactions between nanoparticles and cells in drug delivery should be carefully examined according to the physicochemical properties of nanoparticles such as the type of materials, size and mainly surface charge in a biomimetic microfluidic condition.

Shear connectors are used in steel beam–concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. We performed push-out tests of stubby Y-type perfobond rib shear connectors for composite frames. These shear connectors have relatively small ribs than conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

COPD is currently the fourth leading cause of death in the world. Globally, due to continued exposure to COPD risk factors and an aging population, the burden of COPD is expected to increase in the coming decades. The BODE (body mass index, airflow obstruction, dyspnea, and exercise capacity) index is a practical and multidimensional predictor for prognosis of COPD, and better than FEV1.We used the database of Kaohsiung Chang Gung Memorial Hospital medical center, Taiwan to analyze the correlation between BODE index, healthcare resource utilization, and Charlson comorbidity index (CCI). This retrospective study to collect COPD patients with complete BODE index data who had undergone a 6-minute walk examination in our hospital from January 2015 to December 2016. The medical cost and comorbidities database were analyzed from January 1, 2015, to August 31, 2017. Of 396 patients, 382 (96.5%) were male, with an average age of 71.3 ± 8.4 years. There was a significant association between the BODE index and the CCI of COPD patients (p < 0.001). Healthcare resource utilization was positively correlated with the BODE index during the 32 months of retrospective clinical outcomes: positively correlated with the number of hospitalizations (p<0.001), hospitalization days (p<0.001), hospitalization expenses (p=0.005), and total medical expenses (p=0.024), respectively. Our findings provide the crucial information for clinician to predict medical burden and comorbidities in patients with COPD by using BODE index.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

Most shear tests are performed as standard three- or four-point bending tests, i.e., on one-way simply supported specimens subjected to concentrated loads. The major disadvantage is that these conditions usually do not correspond to the support and load condition of real structures. Structural members such as beams or slabs, are often multi-span components and subjected to distributed loads. As a consequence, the complex shear behavior, including crack kinematics, shear transfer mechanisms, and shear capacity, is studied almost only simply supported members with concentrated load. Positive impacts on the shear behavior resulting from continuous systems and distributed loads are thus neglected in the derivation of calculation models and in the development of design specifications. To incorporate the effect of continuous members and distributed loading conditions, more experimental investigations are necessary. Therefore, a total of 16 bending shear tests on CFRP reinforced concrete members without shear reinforcement were carried out. The tests specimens were tested as simply supported beams or as simply supported beams with loaded cantilever to simulate the continuous system with concentrated and distributed loads. Furthermore, the shear slenderness was varied by using different span lengths and degrees of restraint in the systems with intermediate support. All test specimens were made of high-strength concrete and were reinforced with a multilayer grid-like CFRP reinforcement in longitudinal direction. There was no shear reinforcement installed in the investigated shear span. This paper focuses the influence of the support conditions and load arrangements on crack development as well as on shear strength.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

Optical modes bearing optical vortices are important light systems in which to encode information. Optical vortices are robust features of optical beams that do not dissipate upon propagation. Thus decoding the modal content of a beam is a vital component of the process. In this work we present a method to decode modal superpositions of light beams that contain optical vortices. We do so using shear interferometry, which presents a simple and effective means of determining the vortex content of a beam, and extract the parameters of the component vortex modes that constitute them. We find that optical modes in a beam are easily determined. Its modal content can be extracted when they are of comparable magnitude. The use of modes of well defined topological charge but not well defined radial-mode content, such as those produced by phase-only encoding, are much easier to diagnose than pure Laguerre-Gauss modes.

The boreal Hemisphere has been experiencing increasing extreme hot and dry conditions over the past few decades, consistent with anthropogenic climate change expectations. The continental extension of the phenomenon calls for tools and techniques capable of monitoring the global to regional scales. In this context, the satellite is the only system that can satisfy the need for global coverage. The main objective we have addressed in the present paper is the capability of infrared satellite observations helping to monitor the vegetation stress due to increasing drought and heatwaves in summer. We have designed and implemented a new water deficit index (wdi) that exploits satellite observations in the infrared to retrieve humidity, air temperature, and surface temperature simultaneously. These three parameters are combined to provide the water deficit index. The index has been developed based on the Infrared Atmospheric Sounder Interferometer or IASI, which covers the infrared spectral range 645 to 2760 cm-1 with a sampling of 0.25 cm-1. The index has been used to study the 2017 heatwave, which hit Continental Europe from May to October. In particular, we have examined Southern Italy, where Mediterranean forests suffer from climate change. We have computed the index's time series and show that it can be used to indicate the atmospheric background conditions associated with meteorological drought. We have also found a good agreement with soil moisture, which suggests that the persistence of anomalously high water deficit index was an essential driver of the rapid development and evolution of the exceptionally severe 2017 droughts.

Chronic stress in dairy cattle industry has negative impacts on animal health, productivity, and welfare. It has been confirmed that cortisol transfers to milk and resists the high temperature during milk processing. This study evaluated the relationship between milk cortisol concentration (MCC) in commercial milk products and the temperature-humidity index (THI) at time of milk production. Eleven commercially produced pasteurized and sterilized milk products, purchased in Chuncheon, Korea, with production dates ranging from July to October 2021 were analyzed. The MCC was extracted using diethyl ether and analyzed using enzyme immunoassay. Average THI values based on microclimate data provided by the Korea Meteorological Administration were 77±0.8, 75±1.4, 69±1.4, and 58±1.8, in July, August, September, and October, respectively. The average MCC levels were 211.9±95.1, 173.5±63.8, 109.6±53.2, and 106.7±33.7 pg/mL in July, August, September, and October, respectively. MCC in July was higher than in August, September and October (p<0.05), while it was lower in September and October than in August (p<0.05). Significant variations in MCC were observed in commercial milk products across the four production months (p<0.05), except for two milk products. Overall, monitoring cortisol residue in commercial dairy milk products can be an alternative indicator of stress in dairy cattle of farms.

Eccentric punching shear can occur in concrete slab-column connections when the connection is subjected to shear and unbalanced moments. Typically, this situation results in edge and corner columns and is thus a common practical case. However, most punching experiments in the literature are concentric punching shear. This paper presents a developed database of eighty-eight experiments of flat slabs under eccentric punching shear, including a summary of the testing procedure of each reference and a description of the slab specimens. Additionally, a linear finite element analysis of all the specimens is included to determine the relevant sectional shear forces and moments. Finally, the ultimate shear stresses from the database experiments are compared to the shear capacities determined with ACI 318-19, Eurocode 2 NEN-EN 1992-1-1:2005, and the Model Code 2010. The comparison shows that the Model Code 2010 is the most precise in the predictions with an average tested over predicted ratio of 0.96 and a coefficient of variation of 27.96%. It can be concluded that this study represents the inconsistencies of the currently used design methods and the lack of experimental information.

The paper argues that universal approaches to infiltration and drainage in permeable media that pivot around capillarity and that led to dual porosity, non-equilibrium, or preferential flow need to be replaced by a dual process approach. One process has to account for relatively fast infiltration and drainage based on Newton's shear flow, while the other one is responsible for storage and relatively slow redistribution of soil water by focusing on capillarity. Already Schumacher (1864) postulated two separate processes. However, Buckingham's (1907) and Richards' (1931) apparent universal capillary-based approach to flow and storage of water in soils dominated. The paper introduces the basics of Newton's shear flow in permeable media. It presents experimental support for the four presumptions of (i) sharp wetting shock fronts; (ii) that move with constant velocities; (iii) atmospheric pressure prevails behind the wetting shock front; (iv) laminar flow. It further discusses the scale tolerance of the approach, its relationship to Darcy's (1856) law, and its extension to solute transport.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

This paper aims to investigate the feasibility of strengthening the web opening in the shear zone of RC beams by using iron-based shape memory alloy (Fe-SMA) bars. To conduct this study, numerical analysis with ABAQUS software was employed. The research was divided into six groups of beams with web openings of different lengths (150, 300, and 450 mm), prestressing levels (0%, 30% and 60%), and reinforcement diameters (14, 18, and 22 mm) of Fe-SMA bars. The results show that the presence of web openings can cause a significant reduction in the cracking and ultimate loads of the beams, with reductions ranging from 11 to 50% and 36 to 48%, respectively. However, by adding pre-stressed Fe-SMA bars around small web openings (100×150 mm), the shear capacity of the beam is restored, and the beam exhibits behavior similar to solid beams. Additionally, activating the Fe-SMA bars by 30 and 60% resulted in almost similar cracking loads but improved load-carrying capacity of the beam with small openings by 12% and 9%, respectively, compared to the solid beam. The technique proposed for enhancing shear strength is most effective for beams with small (100×150 mm) and medium (100×300 mm) web openings as it can restore both the beam’s shear strength and stiffness. However, for beams with larger web openings (100×450 mm), the use of activated Fe-SMA beams can recover almost 90% of the solid beam's shear capacity. Furthermore, reinforcing small openings with Fe-SMA bars of different diameters enhances beam shear capacity and stiffness, while for larger openings, higher Fe-SMA reinforcement ratios could potentially restore the beam's full strength and stiffness. This study emphasizes the importance of strengthening web openings in RC beams, particularly in shear zones, and provides significant insights into how to strengthen beams with web openings, thereby contributing to developing safer structures. However, further laboratory experiments are recommended to validate, complement and extend the findings of this numerical study.

Droughts are a common occurrence in various climates and are primarily caused by a prolonged decrease in rainfall. Several factors contribute to droughts, including temperature, wind speed, relative humidity, rainfall timing, amount, and intensity during the growing season. The objective of this study is to establish a new index, named soil moisture and evapotranspiration revealed drought index (SERDI), for displaying dry and wet conditions based on combining both soil moisture and evapotranspiration (Penman-Monteith) to improve drought early warning and its severity globally. For validation of the SERDI with other indices such as LST, VHI, NDVI, and NDWI, different ways used such as R-square, RMSE, MAPE, and P-value to estimate the accuracy, variability of data, the forecast conditions, and how the significance of data. The results showed that the low RMSE and high r² were found between SERDI with LST and VHI. In contrast, the low R- square and high RMSE were between SERDI with NDVI and NDWI in most of the semi-arid areas. Furthermore, most of the semi-arid areas from Iran, Iraq, Syria, Jordan, and Israel experienced moderate and severe dry conditions, except some parts of these regions had normal conditions in Iran and Syria. The SERDI analysis revealed a strong correlation between (LST) and a moderate correlation with (VHI) across all study areas. However, the relationship between other indices, like (NDWI) and (NDVI), varied depending on the regions. To conclude, SERDI can be used globally for detecting drought based on soil moisture and evapotranspiration.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

This manuscript employs a surface stress-driven nonlocal model to explore the combined effects of long-range interaction and surface energy on higher vibration modes of functionally graded nanobeams. The nanobeam theory, based on Bernoulli-Euler kinematics, incorporates surface effects such as surface elasticity, surface residual stresses, surface density, and rotary inertia. Hamilton's principle is applied to derive the governing equation with size-dependent considerations. The main outcomes of a parametric investigation, considering four different kinematic boundary conditions (Cantilever, Simply-Supported, Clamped-Pinned, and Doubly-Clamped) while varying the nonlocal parameter and material gradient index, are presented and discussed. Additionally, the normalized natural frequencies for the second, third, fourth and fifth modes of vibrations are provided and analyzed for each case under study. The results underscore the model's effectiveness in capturing surface energy effects on the overall dynamic behavior of functionally graded Bernoulli-Euler nanobeams, offering a cost-effective approach for designing and optimizing nano-scaled structures.

A large set of undrained compression triaxial tests was carried out on different types of cohesionless soils, from sands to silty-sands and silts. Shear wave velocity measurements were carried out alongside. These tests exhibited distinct state transitions ranging from flow liquefaction to strain softening or strain hardening. With the purpose of defining a framework to assess soil liquefaction, it was found that the ratio between the shear wave velocity (VS0) and the peak undrained deviatoric stress, qpeak, VS0/qpeak, could be accurately used to define a boundary between liquefaction and strain hardening for sands, and between strain softening and strain hardening for silty-sands and silts. Since this ratio is a function of the tested material, it was also discovered that the prediction of these boundaries could be made as a function of soil grading, namely via the coefficient of uniformity, CU. Despite not being regarded as a strong geomechanical parameter, CU is easily determined from a grain-size distribution test and it has an empirically proven correlation with critical state parameters.

Shear thickening fluids (STF) are a class of fluids whose viscosity significantly rises under external loads. The research on these fluids has been advancing in recent years regarding prospective practical applications, including developing impact-absorbing composites. Following the green agendas governments and legislators advocate, this study investigates the combination of STF and other sustainable materials. Cork is a naturally occurring cellular material with a negative carbon footprint and superior energy absorption properties. With varying concentrations of STF material, cork agglomerates were formed. Notably, the analysed blends are homogeneous, contrasting with previous literary works. A series of experiments were conducted in quasi-static and dynamic conditions to determine the various mechanical responses. STF appears to influence the mechanical behaviour of cork agglomerates by providing softer deceleration rates and dispersing more energy through disaggregation mechanisms.

The International Roughness Index (IRI) is the standard scale for evaluating road roughness in many countries in the world. The Taipei City government actively promotes a Road Smoothing Project and plans to complete the rehabilitation of the main and minor roads within its jurisdiction. This study aims to detect the road surface roughness in Taipei City and recommend appropriate IRI thresholds for road rehabilitation. A total of 171 asphalt concrete pavement sections in Taipei City with a total length of 803.49 km were analyzed and compared by IRI. The longitudinal profile of the detected road sections was measured using an inertial profiler. The statistical analysis showed that the IRI value prior to road leveling was mainly distributed between 5 and 8 m/km, while the IRI value after road leveling was mainly distributed between 3 and 4.5 m/km. This confirms that the implementation of the Road Smoothing Project has a significant effect on improving road smoothness. Moreover, based on the analysis results, it is recommended that the IRI threshold value for road rehabilitation in Taipei City be set at 4.50 m/km.

Abstract: Brassinosteroids (BR) are essential plant hormones that play a crucial role in regulating plant growth and development, as well as their resistance to abiotic and biotic stresses, including pathogen infections. In the context of plant im-munity, BR influence various processes such as the expression of genes related to pathogen defense, the production of antimicrobial compounds, and the re-inforcement of the plant cell structure. The aim of work is understand the role of BR in plant defense against abiotic and biotic stresses. BR are involved in the regulation of metabolic processes, water economy, and photosynthesis, contributing to increased plant resistance to abiotic stresses. The study discusses various mechanisms of BR action on plant immunity, including the regulation of gene expression related to defense, activation of the plant defense system, in-teraction with other plant hormones, regulation of water and salt balance, and influence on photosynthetic processes. In the context of plant immunity, BR influence various processes, including the expression of genes related to pathogen defense, the production of antimicrobial compounds, and the reinforcement of the plant cell structure. Additionally, BR are involved in the regulation of metabolic processes, water economy, and photosynthesis, con-tributing to increased plant resistance to abiotic and biotic stresses. The paper emphasizes the importance of further research on the role and mechanisms of action of BR in plant immunity, which may contribute to the development of more effective strategies for the use of BR in agriculture, horticulture, and plant protection.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

The biological aging, characterized by changing in metabolism and physicochemical properties of cells, has an impact on public health. Environment and lifestyle including factors like diet and physical activity seems to play a key role in healthy ageing. Several studies have shown that regular physical activity can enhance antioxidant defence mechanisms, including the activity of enzymes such as superoxide dismutase (SOD), catalase, and glutathione peroxidase. However, intense or prolonged exercise can also lead to an increase in ROS production temporarily, re-sulting in oxidative stress. This phenomenon is referred as "exercise-induced oxidative stress". The relationship between physical activity and oxidative stress in aging is complex and depends on various factors such as the type, intensity, duration, and frequency of exercise, as well as in-dividual differences in antioxidant capacity and adaptation to exercise. In this review, we ana-lyzed what is reported from several authors regarding the role of physical activity on oxidative stress in aging process as well as the role of hormesis and physical exercise as tools for preven-tion and treatment of sarcopenia, an aging related disease. Finally we reported what has recently been studied in relation to the effect of physical activity and sport on aging in women

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Star block-copolymers (SBCs) are macromolecules formed by a number of diblock copolymers anchored to a common central core, being the internal monomers solvophilic and the end monomers solvophobic. Recent studies have demonstrated that SBCs constitute a self-assembling building blocks with specific softness, functionalization, shape, and flexibility. Depending on different physical and chemical parameters the SBCs can behave as flexible patchy particles. In this paper, we study the rotational dynamics of isolated SBCs using a hybrid mesoscale simulation technique. We compare three different approaches to analyse the dynamics: the laboratory frame, the non-inertial Eckart's frame, and a geometrical approximation relating the conformation of the SBC to the velocity profile of the solvent. We find that the geometrical approach is adequate when dealing with very soft systems while in the opposite extreme, the dynamics is best explained using the laboratory frame. On the other hand, the Eckart frame is found to be very general and to reproduced well both extreme cases. We also compare the rotational frequency and the kinetic energy with the definitions of the angular momentum and inertia tensor different from recent publications.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

The Work Ability Index (WAI) is the most widely used questionnaire for the self-assessment of working ability. Because of its different applications, shorter versions, and widespread use in healthcare activities, it is worthwhile assessing its characteristics. The WAI was distributed online among the workers of a healthcare company; the results were compared with data contained in the workers' personal health records and with absence registers. 340 out of 575 workers (59.1%) participated; 6.5% of them reported poor work ability. Exploratory factor analysis indicated that the one-factor version best described the characteristics of the WAI. The scores of the complete WAI, the shorter form without the list of diseases, and the minimal one-item version (WAS) had equal distribution and were significantly correlated. The WAI score was inversely related to age and significantly lower in women than in men, but it was higher in night workers than in colleagues due to the probable effect of selective factors. The WAI score was also correlated with absenteeism, but no differences were found between males and females in the average number of absences, suggesting that cultural or emotional factors influence the self-rating of the WAI. Workers tended to overreport illnesses in the online survey compared to data collected during occupational health checks. Musculoskeletal disorders were the most frequently reported illnesses (53%). Psychiatric illnesses affected 21% of workers and had the greatest impact on work ability. Multilevel ergonomic and human factor intervention seems to be needed to recover the working capacity of healthcare workers.

There is little doubt that the efficacy of MnDPDP and its therapeutic improved counterpart Ca4Mn(DPDP)5 mainly depends on their MnSOD-mimetic activity when it comes to their potential use as rescue medicines, during e.g., acute myocardial infarction. However, pharmacokinetic considerations suggest that the efficacy of MnDPDP on Pt2+-associated neurotoxicity depends on another action of this drug. Electron Paramagnetic Resonance (EPR) studies have demonstrated that Pt2+ outcompetes Mn2+ and endogenous Zn2+ from binding to fodipir (DPDP), and hence suggest that the previously reported CIPN protective efficacy of MnDPDP is a result of chelation and elimination of Pt2+ by DPDP, which in turn suggests that Mn2+ is unnecessary for efficacy when it comes to oxaliplatin-associated CIPN.

Abstract: Kiwifruit, a perennial horticultural crop known for its nutritional value, faces significant challenges due to biotic and abiotic stresses, affecting its yield and quality. Leucine-rich repeat receptor-like proteins (LRR-RLPs), a major group of receptor-like proteins in plants, have diverse functions in plant physiology, including growth, development, signal transduction, and stress responses. Despite their importance, the specific roles of kiwifruit LRR-RLPs in response to biotic and abiotic stresses remain poorly understood. In this study, we investigated the expression patterns of kiwifruit LRR-RLPs under various stress conditions, including pathogen stress, heat stress, waterlogging stress, and copper stress. Through genome and transcriptome analyses, we identified a total of 101, 164, and 105 LRR-RLPs in Actinidia Chinensis 'Hongyang', Actinidia eriantha 'Huate', and Actinidia chinensis 'Red5' kiwifruit, respectively, classified into 9 subgroups based on phylogenetic relationships. Synteny analysis revealed that the expansion of kiwifruit LRR-RLPs was primarily attributed to segmental duplication events. Using RNA-seq data from pathogen-infected kiwifruits, we identified specific LRR-RLP genes potentially involved in different stages of pathogen infection. Additionally, we observed the potential involvement of kiwifruit LRR-RLPs in abiotic stress responses, with upstream transcription factors possibly regulating their expression. Furthermore, protein interaction network analysis unveiled the participation of kiwifruit LRR-RLP genes in the regulatory network of abiotic stress responses. These findings highlight the crucial roles of LRR-RLPs in mediating both biotic and abiotic stress responses in kiwifruit, offering valuable insights for the breeding of stress-resistant kiwifruit varieties.

: Shear-wave elastography (SWE) has become popular in clinical practice for many diseases.However, there are not adequate research for spleen-related diseases.This study aimed to investigate the potential of quantitative values obtained through SWE in evaluating spleen pathologies in the pediatric population and to demonstrate its perfomance to differentiate splenomegaly-related diseases.Research group retrospectively included children with pathological diagnoses related to spleen from November 2016 to April 2021 and they were categorized three groups as portal hypertension (PH), benign lymphoid hyperplasia (BLH), malignant infiltration (MI).Spleen sizes and parenchymal stiffness were also calculated for each group.Subsequently, mean spleen stiffness in each compared with normal values within the same age group.In total 2781 children (1379 children for study group, 1402 children for control group) were enrolled to the study.The highest stiffness were observed in the PH group, which is statistically higher than others (p&lt;0.05). Although the mean spleen stiffness in the group with BLH was higher than the control and MI group, the difference was not statistically significant (p=0.08).The mean stiffness in the group with MI was significantly lower than both the control group (p=0.005) and PH (p=0.01).In conclusion, using SWE in the differential diagnosis of etiologies causing splenomegaly, could make important contribution.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

This paper initiates the study of the mathematical aspects of the ad-hoc Lanzhou index. If G is a graph with the vertex set {x1,⋯,xn}, then the ad-hoc Lanzhou index of G is defined by Lz¯(G)=∑i=1ndi(n−1−di)2, where di represents the degree of the vertex xi. Several identities for the ad-hoc Lanzhou index, involving some existing topological indices are established. The problems of finding graphs with the extremum values of the ad-hoc Lanzhou index from the following sets of graphs are also attacked: (i) set of all connected ξ-cyclic graphs of a fixed order, (ii) set of all connected molecular ξ-cyclic graphs of a fixed order, (iii) set of all graphs of a fixed order, (iv) set of all connected molecular graphs of a fixed order.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

Background/Objectives: Vitamin B12 deficiency can cause variable symptoms, which may be irreversible if not diagnosed and treated in a timely manner. We aimed to develop a widely accepted expert consensus to guide the practice of diagnosing and treating B12 deficiency. Methods: We conducted a scoping review of the literature published in PubMed since January 2003. Data were used to design a two-round Delphi survey to study the level of consensus among 42 experts. Results: The panelists agreed on the need for educational and organizational changes in the current medical practices for diagnosing and treating B12 deficiency. Recognition of clinical symptoms should receive the highest priority in establishing the diagnosis. There is agreement that the serum B12 concentration is useful as a screening marker, whereas methylmalonic acid or homocysteine can support the diagnosis. Patient lifestyle, disease history and medications can provide clues to the cause of B12 deficiency. Regardless of the cause of the deficiency, initial treatment with parenteral B12 was regarded as the first choice for patients with acute and severe manifestations of B12 deficiency. The use of high-dose oral B12 at different frequencies may be considered for long-term treatment. Prophylactic B12 supplementation should be considered for specific high-risk groups. Conclusions: There is a consensus that clinical symptoms need to receive more attention in establishing a diagnosis. B12 laboratory markers can support the diagnosis. The severity of clinical symptoms, the causes of B12 deficiency and the treatment goals govern decisions regarding the route and dose of B12 therapy.

In order to further investigate the study of the effect of grouped stud effect on the force properties of stud connector, based on the premise that the correctness of the finite element simulation method in this paper, finite element modeling of grouped stud connectors was developed, the grouped stud effect and its sensitivity factors were analyzed, to validate the recommended formula for calculating the shear capacity of grouped stud connectors. Results show that the number of grouped stud rows and row spacing have a significant effect on the grouped stud effect, and the unevenness coefficient of grouped stud force Ⅰ is negatively correlated with the number of grouped stud rows as well as the grouped stud row spacing. For grouped stud connectors with commonly used concrete grades greater than C50 and height-to-diameter ratios greater than 4 in steel-concrete composite structural bridges, which is insensitive to changes in the concrete strength grades and the length of the studs. The direction of force transmission for the grouped stud changes with the change of loading angle, and the unevenness coefficient of force for the grouped stud will therefore be reduced. By comparing the results of the 62 existing groups of grouped stud connectors push-out tests, the mean value of the ratio of tested to calculated values is found to be 1.12, the variance is 0.023, the dispersion is small, it is shown that the recommended formula has a high degree of accuracy. The results of this paper can be used as a theoretical basis for the study of the shear stress performance of grouped stud connectors.

A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.

The need for miniaturized shear force sensors is expanding, particularly for biomedical applications. Examples include measuring interfacial shear stresses between a human and an external device (e.g., footwear or a prosthesis). However, there are considerable challenges in designing a shear sensor for these applications due to the need for a small package, low power requirements, and resistance to interference from motion artifact and electromagnetic fields. This paper presents the design, fabrication, and characterization sensor that measures two-axis shear force by detecting displacement between a color panel and a red, green, and blue light-sensing photodiode. The sensor response to applied displacements and forces was characterized under benchtop testing conditions. We also present the design of a prototype wireless version of the sensor for integration into footwear. The sensor exhibited strong agreement with gold standard measurements for two axis shear displacements (R2>0.99, RMSE≤5.0 µm) and forces (R2>0.99, RMSE≤0.94 N). This performance, along with the sensor’s scalability, miniaturized form, and low power requirements make it well-suited a variety of biomedical applications.

Among the most important variables in the design of falling film microreactors (FFMRs) is the liquid film thickness as well as the gas/liquid interfacial area, which dictate the mass and heat transfer rates. In a previous work conducted in our lab the characteristics of a free-falling Newtonian liquid film have been studied and appropriate correlations have been proposed. In this work the geometrical characteristics of a non-Newtonian shear thinning liquid, flowing in an inclined open microchannel, have been experimentally investigated and design correlations that can predict with reasonable accuracy the features of a FFMR have been proposed. The test section used was an open μ-channel with square cross section (Wo=1200 μm) made of brass which can be set to various inclination angles. The liquid film characteristics were measured by a non-intrusive technique that is based on the features of a μ-PIV system. Relevant CFD simulations revealed that the volume average dynamic viscosity over the flow domain is practically the same as the corresponding asymptotic viscosity value, which can thus be used in proposed the design equations. Finally, a generalized algorithm for the design of FFMRs, containing non-Newtonian shear thinning liquids, is suggested.

Background: The workplace burnout syndrome is often associated with particular aspects of certain job positions, especially those which entail working with people with special needs. The burnout syndrome in healthcare jobs is a serious problem which has grown into an epidemic among healthcare workers and associates. Objectives: The aim of this research is to assess the presence of stress and burnout syndrome at work with healthcare workers, expert workers, professional associates and associates in social service institutions in Belgrade. Material and Methods: This research has been conducted in the form of a cross-sectional study of a representative sample in social institutions in Belgrade. It has been conducted from March to the end of June of 2023. The sample of the study had 491 participants. The questionnaires used were a structured instrument with social-demographic and social-economic characteristics, workplace characteristics, life style characteristics, and the following questionnaires: DASS-21, Copenhagen, Brief Resilience Scale, and Brief Resilient Coping Scale. Results: The end results indicate the following to be significant risk factors for the occurrence of workplace burnout syndrome: overtime (OR=2.62; CI=1.50-4.56), BRS average score (OR=0.28; CI=0.17-0.44), DASS21 D heightened depression (OR=2.09; CI=1.1-4.04), DASS21 A heightened anxiety (OR=2.38; CI=1.34-4.21), DASS21 S heightened stress (OR=2.08; CI=1.11-3.89). The only protective risk factor which stood out was the self-assessment of health levels (OR=0.60; CI=0.42-0.85). Conclusion: Overtime is a significant predictor of workplace burnout. Apart from it, other significant predictors of workplace burnout were heightened depression, anxiety, and stress levels.

Probiotics are microorganisms infused in products for health benefits including acceleration of nutrient digestion, however, it is also important to ensure the safety prior to incorporation. Here, we present evidence of the ability of two probiotic isolates,Lacticaseibacillus paracasei BCRC-16100 and Lacticaseibacillus paracasei ZFM54, in the (1) enhancement of carbohydrate digestion, (2) tolerance to stress, and (3) antibiotic resistance. Approaches include whole genome sequence (WGS) analysis and bioactivity assays. WGS revealed genes suggesting the ability of the two isolates to promote carbohydrate digestion, tolerance to stress and antibiotic resistance. Carbohydrate digestive ability was confirmed through a biochemical assay where the two isolates cause glucose release from starch. The two isolates also showed versatility in a range of temperature and alcohol concentration. For antibiotic resistance particularly on vancomycin, there are three mechanisms namely transporter control, transcriptional regulation, and efflux pump. Furthermore, promoter and transposable element analysis showed that some of the active antibiotic resistant (AbR) genes can be laterally transferred. Altogether, we show the potential of two probiotic isolates to be incorporated in products for improved carbohydrate digestion and the need to address the removal of active and mobile antibiotic resistance genes that may compromise safety.

The aim of this report is to evaluate the segmental rib index (RI) from T1-T12 spinal level in mild and moderate idiopathic scoliosis (IS) curves of thoracic, thoracolumbar and lumbar type by gender. The relationship of segmental RI to the frontal plane radiological deformity presented as the Cobb angle and to the posterior truncal surface deformity presented as the scoliometric readings of Angle of Trunk Rotation (ATR) in these patients is also assessed. Any statistical significant rela-tionship of these parameters would be very important for biomechanical relations of the rib cage (RC) deformity presented as the rib hump deformity (RHD) and the deformity in the spine and it would thus provide valuable information about scoliogeny. The segmental rib index (RI) is presented in 83 boys and girls with mild and moderate IS. The measurements include the scoliometric readings for truncal asymmetry (TA), the Cobb angle assessment and the segmental RI from T1-T12. The statistical package SPSS 23 was used for statistical analysis. The TA is documented and the Cobb angle is presented by gender and curve type. The segmental RI of thoracic, thoracolumbar and lumbar curves are presented for the first time. The correlations of the segmental RI to surface deformity presented as the rib hump deformity (RHD) in all IS patients and particularly in thoracic curves, to Cobb angle by gender and age and the comparison of the segmental RI index of asymmetric but not scoliotic children to the scoliotic peers by curve (in thoracic, thoracolumbar, lumbar curves) in boys and girls are presented. The findings emphasize the significant protagonistic role of the thoracic asymmetry in relation to the spinal deformity mainly in girls for the thoracic and in boys for the thoracolumbar curves. The cut-off point of age of the examined scoliotics is 14 years, that is when the RI shows stronger correlation with the spinal deformity, namely when the thoracic deformity is decisively effective to the developing thoracic spinal deformity, in terms of Cobb angle. In summary, the results of this study provide aetiological implications for IS, as far as the role of thorax is con-cerned.

The Metropolitan Economic Freedom Index (MEFI) ranks cities based on their support of free market enterprise. In its current state, MEFI purports to measure three constructs (government spending, taxation, and labor market freedom) with three equally weighted variables for each one, assuming perfect substitutability of variables. This study investigates the statistical consistency of MEFI through Confirmatory Factor Analysis. Multiple models investigate current variable selection by providing a potentially better indicator of labor market freedom, aggregation assumptions by removing the requirements for fixed and equal weights, and statistical consistency by evaluating the fit between the data and models. Results indicate that the current MEFI model is not statistically consistent with the data, that weighting of variables should not be equal, that variable selection should be investigated, and that constructs should be re-imagined. The models investigated provide an initial starting point for redefining MEFI.

This general review assesses the impact of physical exercise on oxidative and nitrosative stress and the counteractive role of antioxidants, drawing from a systematic literature search up to March 2024 in databases like PubMed and Web of Science. The review highlights studies on the effect of exercise on the production of reactive oxygen species (ROS) and reactive nitrogen species (RNS) and antioxidant responses in both human and animal models based on rigorous inclusion and exclusion criteria. Due to the variety of exercise types and participants' characteristics, a narrative synthesis approach was adopted. The findings indicate that moderate exercise boosts antioxidant defenses, known as hormesis, whereas excessive physical activity may increase oxidative and nitrosative damage. The review also explores the complex effects of antioxidant supplementation, revealing that while natural dietary antioxidants support health, high-dose supplements could potentially hinder positive adaptations to exercise. Recommendations for athletes and the general active population highlight the importance of balancing exercise and dietary intake to optimize health benefits. The review concludes with a call for more detailed research on tailored exercise and nutrition plans to dissect these intricate relationships further.

(1) Background: Patella and achilles tendon injuries have become increasingly prevalent due to an increasingly active population. These injuries can cause significant dysfunction which is especially true for elite athletes. Standard B-Mode ultrasound has been useful in the diagnosis of these injuries, however, only to a limited extent. Shear wave elastography (SWE) can aid in evaluation by objectively measuring tissue stiffness. Prior studies have proven shear wave values can be used to evaluate tendon tissue noting differences in healthy versus pathologic tendons. One main limitation remains a lack of normative data for specific tendon tissues which we aim to address in this study; (2) Methods: A cross-sectional study of healthy volunteers aged 18-65 without lower extremity injury was evaluated using A Samsung RS85 Prestige ultrasound machine with a 14L-2 MHz transducer. Shear wave values were collected in a standardized manner for the patellar tendon at one location, as well as the achilles tendon at the midportion and insertional areas; (3) Results: Data for 54 healthy adult patellar and achilles tendons was collected bilaterally. The mean SWE average of the patellar tendon (P1-P3) for all subjects was 96.3 +/- 10.9 kPA. A higher BMI was correlated with a decrease in patella tendon kPA and the mean PT1 was higher for males compared to females (adjusted mean 96.4 kPA for males and 88.5 kPA for females, mean difference = 7.9 kPA; P = 0.009). The mean SWE average of the insertional Achilles (AT1-AT3) for all subjects was 101.7 +/-16.2 kPA and for the midportion achilles (MTP1-MTP5) was 145.6 +/- 18.8 kPA. There was a decrease in kPA for insertional Achilles measurements in those with a higher BMI, but this did not reach statistical significance (p=.12); (4) Conclusion: This study provides normative SWE values for the patella and achilles tendon using the Samsung RS85. These values can be used for comparison to pathological tissue by means of the same examination protocol to better understand tendon degeneration. Further studies are warranted as to how SWE can be applied to the diagnosis of tendinopathy, partial and full-thickness tears, and response to treatment.

Bare slope instability is a prevalent concern. The root system of, herbaceous vegetation enhances the shear strength of shallow–slope soil. Indoor experiments were conducted on rootless undisturbed soil (RUS) and undisturbed soil with a root system (USRS) using a triaxial compression apparatus to analyze the slope stability of composite soil with a Tagetes erecta root system. Significance tests and correlation analysis of the factors affecting shear performance were conducted using R software. The slope reinforcement, effect by the plant root system was simulated under 24 working conditions using the MIDAS finite element method. The results revealed the influence of the–root content (RC), moisture content (MC), and stress on the shear strength of USRS, the contribution degree, and the variables’ influences on slope stability. Both RUS and USRS exhibited strain hardening during shearing. The internal friction angle (φ) and cohesion (c) of USRS were negatively and positively correlated with the RC and MC (root burial depth), respectively, and a good fit was obtained for the relationship. The maximum deviatoric stress during shear failure was 1.29 times higher for USRS than for RUS. The RC (root depth) was positively correlated with the slope safety coefficient and the slope of the line under different working conditions, whereas the slope gradient was negatively correlated with the slope safety coefficient. The reinforcement effect by the root system resulted in a 13.2% increase in the safety coefficient and improved stability of slopes with a gradient larger than 1.5%. This article investigated the mechanism of the root–soil system and, the effects of different influencing factors on the shear strength of the soil, and slope stability. The findings provide new insights into shallow slope stability in practical slope protection projects.

This study aims to assess the interface shear adhesion behaviour between compacted clay and a metallic surface. A new testing approach was developed in this study for this purpose. The proposed method is simple and requires neither advanced equipment nor special test procedures, and thus represents an improvement on existing practice in this field. The experimental program involves determining the interface shear adhesion strength of reconstituted Kaolin clay/metallic surface where the Kaolin clay testing specimens were compacted dynamically at different energy levels and moisture contents. In general, the results show that the interface shear adhesion strength increases as the dry density of the clay increases, whereas it decreases as the moisture content increases. Furthermore, the results in this study reveal a unique multistage interfacial shear adhesion strength behaviour as the moisture content changes that could be related to the compaction curve of the clay. The observed behaviour, in this study, could be interpreted in terms of the effect of clay dry density and moisture content on the contact area and moisture-induced capillary adhesion at clay particles-continuum interface surface.

Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a lot of structures in Europe and North America are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extent their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile reinforced mortar (CTRM) to bridge deck slabs and the webs of prestressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM-layer is a combination of a corrosion resistant carbon fibre reinforced polymer (CFRP) fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.