To meet the growing interest in the development of innovative biological nutrient removal (BNR) alternatives for energy neutrality, resource recovery, and decarbonization, the adsorption/bio-oxidation (A/B) process has been widely studied for carbon capture and shortcut nitrogen (N) removal, while limited research has focused on incorporating enhanced biological phosphorus (P) removal (EBPR), mainly due to the differential carbon usage characteristics of functionally relevant microorganisms. Here, a full-scale pilot testing with an integrated system combining A-stage high-rate activated sludge (HRAS) with B-stage partial (de)nitrification/anammox and side-stream EBPR (HRAS-P(D)N/A-S2EBPR) was conducted treating real municipal wastewater. The results demonstrated that, despite the low influent carbon load, the B-stage P(D)N-S2EBPR system achieved effective and stable P removal performance, especially when the volatile fatty acid (VFA) load from A-stage was elevated. Sludge fermentation in both A-stage and B-stage promoted carbon redistribution and likely provided more competitive advantages for ammonium-oxidizing bacteria and polyphosphate accumulating organisms, leading to carbon-efficient shortcut N removal mainly through partial nitrification pathway and influent carbon-independent EBPR simultaneously. Exposure to high VFA levels was considered a potential selection factor for the suppression of nitrite-oxidizing bacteria in the system. The involvement of internal carbon-accumulating organisms would potentially play an important role in endogenous denitrification. This study provided new insights into the effects of incorporating side-stream EBPR into the A/B process on microbial ecology, metabolic activities, and system performance.

We monitored the water quality and hydrological conditions of a horizontal subsurface constructed wetland (HSSF-CW) in Beijing, China, for 2 years. We simulated the area rate constant and the temperature coefficient with the first-order kinetic model. We examined the relationships between the nitrogen (N) removal rate, N load, seasonal variations in the N removal rate, and environmental factors, such as the area rate constant, temperature, and dissolved oxygen (DO). The effluent ammonia (NH₄⁺-N) and nitrate (NO₃⁻-N) concentrations were significantly lower than the influent concentrations (p<0.01, n=38). The NO₃⁻-N load was significantly correlated with the removal rate (R²=0.9566, p<0.01), but the NH^₄+-N load was not correlated with the removal rate (R²=0.0187, p>0.01). The area rate constants of NO₃⁻-N and NH₄⁺-N at 20 °C were 27.01±26.49 and 16.63±10.58 m∙yr⁻¹, respectively. The temperature coefficients for NO₃⁻-N and NH₄⁺-N were estimated at 1.0042 and 0.9604, respectively. The area rate constants for NO₃⁻-N and NH₄⁺-N were not correlated with temperature (p>0.01). The NO₃⁻-N area rate constant was correlated with the corresponding load (R²=0.9625, p<0.01). The NH₄⁺-N area rate was correlated with DO (R²=0.6922, p<0.01), suggesting that the factors that influenced the N removal rate in this wetland met Liebig's law of the minimum.

An increasing body of evidence shows that seaweeds, including kelp, can be used as a tool to neutralize or remove excess nutrients and metals from the water column. Here we report on a preliminary field assessment showing potential nutrient and carbon removal differences by sugar kelp and ribbon kelp grown in common gardens. Seawater and tissue samples were collected systematically from two farms in Alaska. Results show differences between % N and % C content between ribbon kelp (Alaria marginata) and sugar kelp (Saccharina latissima). Results also show that tissue nitrogen in ribbon kelp varies sharply due to nitrogen availability in the water column. In contrast, the percentage of tissue N in sugar kelp remains comparatively stable. Our outcomes provide insight into potential differences in nutrient removal and harvest timing for different kelp species.

Water pollutants removal by biomass adsorbent has been considered innovative and cost effective, thus commendable for application in industrial applications. However, certain important aspects have been overlooked by researchers, namely the efficiency in the operation time and pollutant removal. In this research, landfill leachate samples with organic components were treated using bentonite-enriched with sawdust augmented (SBR) process. By modifying the pH, the sawdust samples were categorized into three: the acidic, the alkaline, and the neutral. To bentonite samples, the pH-adjusted sawdust was added at 10%, 20%, and 30% amounts by mass respectively. At the optimum aeration rate of 7.5 L/min and contact period of 22 h, the treatment achieved 99.28% and 95.41% removal of COD and NH₃-N with bentonite respectively. For both pollutants, in the presence of sawdust, the removal reduced by about 17% with contact period reduced to 2 h which was a considerable achievement.

With the ongoing amendment of the EU legislation on the treatment of urban wastewater, stricter requirements for the removal of pollutants are expected, which calls for the need for innovative wastewater treatment technologies. Biological systems are still the first choice. The survey of typical bioreactors applied in wastewater treatment is presented. Wastewater treatment objective, bio-chemical environment and microbial growth are selected as a main criterion for classification of these bioreactors. Hydraulic and kinetic aspects are considered, advantages and drawbacks of these bioreactors regarding the selection of appropriate type of the reactor as well as regarding operation of reactors are mentioned. The aim of this paper is to provide operators and designers with a brief overview of selected traditional and advanced processes, reactors, and technologies for nutrient removal from municipal wastewater. Another goal is to discuss the possibilities and limitations to comply with more strict effluent standards. From the evaluation of the published papers, it follows that the currently applied traditional methods of nutrients removal have the potential to convey also with the expected stricter limits.

Adding a submerged zone (SZ) is deemed to promote denitrification during dry periods and thus improve NO3--N removal efficiency of a bioretention system. However, few studies had investigated the variation of nitrogen concentration in the SZ during dry periods and evaluated the effect of the variation on nitrogen removal of the bioretention system. Based on the experiment in a mesocosm bioretetion system with SZ, this study investigated the variation of nitrogen concentration of the system under 17 consecutive cycles of wet and dry alternation with varied rainfall amount, influent nitrogen concentration and antecedent dry periods (ADP). The results indicated that (1) during the dry periods, NH4+-N concentrations in SZ showed an exponential decline trend, decreasing by 50% in 12.9 ± 7.3 hours; while NO3--N concentrations showed an inverse S-shape decline trend, decreasing by 50% in 18.8 ± 6.4 hours; (2) during the wet periods, NO3--N concentration in the effluent showed an S-shape upward trend; and at the early stage of the wet periods, the concentration was relatively low and significantly correlated with ADP, while the corresponding volume of the effluent was significantly correlated with the SZ depth; (3) in the whole experiment, the contribution of nitrogen decrease in SZ during dry periods to NH4+-N and NO3--N removal accounted for 12% and 92%, respectively; and the decrease of NO3--N in SZ during the dry period was correlated with the influent concentration in the wet period and the length of the dry period.

One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

Natural gas is an important energy source among various fossil fuels. However, natural gas typically contains a significant amount of water vapor, which can pose challenges in its usage. Therefore, the process of removing water vapor from natural gas, known as gas dehydration, is crucial in the gas industry. The presence of water vapor in the gas supply can lead to the formation of hydrates, which can cause issues such as blockages in pipelines. To tackle this problem effectively, gas dehydration makes use of Tri ethylene glycol (TEG) as a drying agent. TEG works by selectively absorbing water vapor from the natural gas flow, thereby significantly reducing its moisture content.In the gas dehydration process, wet gas is treated by using lean glycol in an absorber, where the water vapor is removed. The resulting rich glycol is then recovered and recycled for further use. In this study, we explore the possibility of replacing nitrogen with dry natural gas in the re-generator of the glycol dehydration system. The aim is to evaluate the feasibility and effectiveness of this alternative approach. To assess the performance of both techniques, we employed HYSYS modeling and simulation. Through this analysis, we compared the capital and utility expenses associated with each method while ensuring that the glycol purity requirements remained unchanged. By examining the results obtained from the simulations, we can gain insights into the economic viability and efficiency of utilizing dry natural gas in the re-generator stage of the glycol dehydration process.In addition to the primary purpose of removing water vapor, the wet gas obtained from the stripping mechanisms in the glycol dehydration process can serve additional functions. It can be utilized to power steam pumps and compressors, thereby maximizing energy efficiency within the system. Alternatively, the wet gas can be recycled back into the process for further treatment. To develop a comprehensive understanding of the entire mechanism, we constructed a model based on the actual flow diagram. This model takes into account the various components and processes involved in the glycol dehydration system, including the stripping mechanisms and their connection to other equipment. By analyzing the data and outcomes generated by this model, we can derive valuable insights. These findings can be utilized to optimize the heat and material balance within the plant, ensuring efficient operation and potentially leading to the design of an improved system in terms of energy consumption and overall performance

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

The main objective of this study was to compare the removal efficiency of nutrients using Lactuca sativa, Medicago sativa and Phragmites australis in subsurface flow constructed wetlands with horizontal flow. In order to test water quality, fabricated reactors designed and the plants cultivated in the soil while their root were inside the wastewater. A long time study carried out from spring till end of autumn (9 months) in order to evaluate the difference in removal rate based on the seasonal changes. The highest removal rate was during summer which followed by spring and autumn. Thus, the effect of plants on the removal efficiency of organic matter (COD, BOD), TSS and nutrient (P and TN) appeared to be dependent on the seasonal growth. Phragmites australis the most sensitive species in order the removal of nutrient from wastewater.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Micropollutants belongs to various groups of chemicals. One of the most diverse and large group of them are pharmaceuticals. The presence of pharmaceutical residues in wastewater poses a significant challenge to water quality and environmental health. This paper provides an overview of recent advancements in the removal of pharmaceuticals from water, focusing on various treatment processes and their effectiveness in eliminating micropollutants. Through a review of literature, including studies on ozonation, UV irradiation, sulphate radical-based tech-nologies, and photocatalytic processes, insights into degradation mechanisms and optimal con-ditions for their removal are synthesized. Additionally, with new legislation mandating the monitoring of selected micropollutants and the implementation of quaternary treatment in wastewater treatment plants, the paper discusses prospects for future research and recommen-dations for effective pharmaceuticals removal. Key actions include conducting comprehensive laboratory and pilot trials, implementing quaternary treatment of wastewaters, continuously monitoring of water quality, investing in research and development, and promoting collabora-tion and knowledge sharing among stakeholders. By embracing these strategies, we can work towards safeguarding water resources and protecting public health from the adverse effects of pharmaceutical contamination.

In recent decade water pollution by micropollutants is an increasing environmental concern. Since 2019, due to COVID-19 pandemic, increased stormwater pollution by chlorine based disinfectants has been determined. Research aimed to treat of chlorine contaminated stormwater after outdoors spaces disinfection are very limited. Runoff from disinfected areas and residual chlorine present in stormwater are transported to surface water bodies. Residual chlorine reacts with dissolved organic compounds in water and results the formation of environmentally toxic disinfection by-products. Studies present event low residual chlorine concentrations may pose a risk to aquatic flora and fauna. In this study the efficiency of different filter materials, including peat, wood chips, sawdust (column tests) and ceramzites Leca, Pollytag, Polski, Ceski (batch tests), in retaining residual chlorine were tested in laboratory scale batch and flow through experiment. The best efficiency to retain chlorine presented sawdust (96 %) and ceramzite Leca (76 %). The plants abilities to reduce pollution by chlorine was analyzed in raised garden bed. Research results will contribute to future studies aimed to retain various micropollutants in stormwater using remediation technologies.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

The expanding global population has increased the demand for sustainable protein sources, and microbial protein (MP) has emerged as a promising alternative. However, conventional carbon (glucose) and nitrogen (ammonia, urea) sources needed for MP production pose environmental and economic issues. This study aims to produce protein using lignocellulosic biomass (LCB) as a carbon source and the nitrogen fixation ability of Klebsiella oxytoca M5A1 as a nitrogen source. The study investigates the pretreatment of LCB (switchgrass), enzymatic hydrolysis, protein quantification, and high-performance liquid chromatography system (HPLC) analysis to track glucose utilization and organic acid production. K. oxytoca M5A1 harnessed free nitrogen from the atmosphere through nitrogen fixation and used abundant, cheap glucose from LCB to produce MP and organic acids as by-products. Protein production occurred in two phases: first within the initial 8 hours and secondly, within the last 16 hours. The highest protein concentration was at 40 hours, with approximately 68.3% protein content. HPLC analysis revealed a dynamic profile of glucose utilization and organic acids (Lactic acid, Propionic acid, Acetic acid, and Succinic acid). K. oxytoca M5A1 exhibited an early high rate of glucose consumption, and conversion to organic acids that were later used for second-phase protein production. The acids profile revealed intra-conversion from one acid to another via metabolic pathways (glycolysis and tricarboxylic acid cycle). Overall, leveraging LCB and the nitrogen-fixing ability of K. oxytoca M5A1 for MP production offers an eco-friendly and cost-effective alternative to traditional protein sources, contributing to a sustainable circular economy.

Studies on N balance due to N inputs and outputs and soil N retention to measure cropping system performance and environmental sustainability are limited due to the complexity of measurements of some parameters. We measured N balance based on N inputs and outputs and soil N retention under dryland agroecosystem affected by cropping system and N fertilization from 2007 to 2011 in the northern Great Plains, USA. Cropping systems were conventional tillage barley (Hordeum vulgaris L.)-fallow (CTB-F), no-tillage barley-fallow (NTB-F), no-tillage barley-pea (Pisum sativum L.) (NTB-P), and no-tillage continuous barley (NTCB). Nitrogen rates to barley were 0, 40, 80, and 120 kg N ha-1. Total N input due to N fertilization, pea N fixation, soil N mineralization, atmospheric N deposition, nonsymbiotic N fixation, and crop seed N and total N output due to grain N removal, denitrification, volatilization, N leaching, gaseous N (NOx) emissions, surface runoff, and plant senescence were 28 to 37% greater with NTB-P and NTCB than CTB-F and NTB-F. Total N input and output also increased with increased N rate. Nitrogen sequestration rate at 0 to 10 cm averaged 22 kg N ha-1 yr-1 for all treatments. Nitrogen deficit ranged from 5 to 16 kg N ha-1 yr-1, with greater deficits for CTB-F and NTB-P and higher N rates. Because of increased grain N removal and reduced N loss to the environment and N fertilizer requirement, NTB-P with 40 kg N ha-1 can enhance agronomic performance and environmental sustainability while reducing N inputs compared to other management practices.

Our understanding of pull-apart basins and their fault systems has been enhanced by analog experiments and simulations. However, there has been no opportunity to compare the faults that constitute pull-apart basins with surface ruptures during earthquakes. In this study, we investigated the effects of a 2018 earthquake (Mw 7.5) on a pull-apart basin in the Palu-Koro fault system, Sulawesi Island, Indonesia, using geomorphic observations in digital elevation models, optical correlation with pre- and post-earthquake satellite images. A comparison of active fault traces determined by geomorphology with the locations of surface ruptures from the 2018 earthquake shows that some of the boundary faults of the basin are inactive and that active faulting has shifted to basin-shortcut faults and relay ramps. We also report evidence of lateral spreading, in which alluvial fan materials moved around the end of the alluvial fan. These phenomena may provide insights for anticipating the location of future surface ruptures in pull-apart basins.

Effective oral care is important to maintain a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using bioelectric effect (BE) with those of mechanical electric toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

A single water pollution by dyes is a huge environmental problem; there is a necessity to produce new decolorization methods that are effective, cost-attractive, and suitable in industrial use. Magnetic chitosan polymers offer the advantage of easy separation from the dye solution. In this work, a Chitosan-Fe polymer was synthesized, characterized, and tested for removal of the azo dye Direct Red 83:1 from water. The polymer was characterized in terms of surface morphology (SEM), elemental analysis (EA), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), infrared spectrophotometry (IR), X-ray powder diffraction (XRD) and density functional theory (DFT). The reported results hint that 1 g and pH 7.0 were the best conditions to carry out both kinetic and isotherm models. To understand the adsorption behavior of Direct Red 83:1 onto the polymers, adsorption rate and maximum adsorption capacity were calculated using kinetic tests and isotherm curves respectively. The kinetic data and mechanism of the adsorption process were analyzed by three models and the equilibrium data by three adsorption isotherms. The results indicated that the adsorption process follows a pseudo-second-order kinetics (R2= 0.999) and fits the Temkin isotherm (R2= 0.946), indicating that the adsorption occurred on heterogeneous surfaces. The newly synthesized Chitosan-Fe polymer exhibited good adsorption properties and easy separation of cleaned water.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p&lt;0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p&lt;0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

Gastric cancer (GC) is a highly heterogeneous, complex disease and the fifth most common cancer worldwide (about one million cases and 784 000 deaths worldwide in 2018). CG is lately diagnosed and guarantees a poor prognosis for GC (the 5-year survival rate is less than 20%, but in early detection can reach 90%). This study evaluated the transcriptional profile in tumor gastric samples to find genes highly expressed during tumor establishment and use the related proteins as targets to find new anticancer molecules. Data was collected at Gene Expression Omnibus (GEO) bank to obtain 3 dataset matrices that analyze gastric tumor tissue versus normal gastric tissue, performed microarray using GPL570 platform, and from different sources. The genes found in silico analysis were confirmed in several lines of GC cells by RT-qPCR. The protein data bank was used to find the correspondent proteins. Then a structural-based virtual screening was done to find molecules, and docking analysis was done using the DockThor server. Our results of transcriptomic analysis, together with RT-qPCR, confirm the high expression of the genes AJUBA, FBXL13, CCDC69, CD80 and NOLC1 in GC lines. Based on that, the correspondent proteins were used in SBVS analysis. Five molecules, one each target, MCULE-2386589557-0-6, MCULE-7343047040-0-1, MCULE-5230409338-0-3, MCULE-9178344200-0-1 and MCULE -5881513100-0-29. All molecules have favorable pharmacokinetic, pharmacodynamic and toxicological properties. Molecular docking analysis revealed that the molecules interact with proteins in critical sites for their activity. Using a virtual screening approach, a molecular docking study was performed for proteins encoded by genes that play important roles in cellular functions for carcinogenesis. Combining a systematic collection of public microarray data with a comparative meta-profiling, RT-qPCR, SBVS, and molecular docking analysis provided a suitable approach to find genes involved in GC and work the correspondent protein to strive for new molecules with anticancer properties.

Constructed rapid infiltration system (CRI) is a new type of sewage biofilm treatment technology, but due to its anaerobic zone lacks of the carbon sources and the condition for nitrate retention, its nitrogen removal perfomance is very poor; However, shortcut nitrification-denitrification process presents distinctive advantages, as it saves oxygen, requires less organic matter and needs less time for denitrification compared to conventional nitrogen removal method. Thus, if the shortcut nitrification-denitrification process could be applied to CRI system properly, the simpler, more economic and efficient nitrogen removal method will be obtained. But, as its reaction process shows that the first and the most important step of achieving shortcut nitrification-denitrification is to achieve shortcut nitrification. Thus, in this study, we explored the feasibility to achieve shortcut nitrification, which produces nitrite as the dominant nitrogen species in effluent, by addition of potassium chlorate (KClO₃) to the influent. In an experimental CRI model system, the effects on nitrogen removal, nitrate inhibition and nitrite accumulation were studied, and the advantages of achieving shortcut nitrification-denitrification were also analysed. The results showed that shortcut nitrification was successfully achieved and maintained in a CRI system by adding 5 mM KClO₃ to the influent at a constant pH of 8.4. Under these conditions nitrite accumulation rate was increased, while a lower concentration of 3 mM KClO₃ had no obvious effect. The addition of 5 mM KClO₃ in influent presumably allowed sufficient activity of ammonia-oxidizing bacteria (AOB) but inhibited nitrite-oxidizing bacteria (NOB) strongly enough to result in a maximum nitrite accumulation rate of up to over 80%. As a result, nitrite became the dominant nitrogen product in the effluent. Moreover, if the shortcut denitrification will be achieved in the subsequent research, it could save 60.27 mg carbon source (CH₃OH) consumption when treatment of per liter sewage in CRI system compared with full denitrification process.

A 2-month incubation study was carried out using two soil types to determine nitrogen mineralization of different inorganic-organic amendments. The following seven treatments (T) were established; T1 = control, T2 = 5 g of dry algae per kg of soil (100%DA), T3 = 136g of agri-mat per kg of soil (100%GA), T4 = 61 g of ground grass per kg of soil (100%GG), T5 = 2.5 g of dry algae + 2.5 g of nitrogen fertilizer (NF) per kg of soil (50%DA50NF), T6 = 50%GA50NF, T7 = 50%GG50NF. Three samples per treatment were drawn at 0, 3, 7, 15, 30, 45, and 60 days for mineral-N determination. A 2-month glasshouse experiment was established afterwards with the following five treatments: T1 = Control, T2 = 50%DA, T3 = 50%GA, T4 = 50%GG, and T5 = 100NF. The results indicated that nitrogen mineralization was significantly higher in organic-inorganic amendments compared to sole organic amendments. The percentage differences ranged from 157% to 195%. The 50%DA treatment increased spinach yield by 20.6% in sandy loam and 36.5% in loam soil. It is difficult to fully recommend the 50%DA treatment without field-scale evaluation, but it is a promising option to be considered.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

Balanced nitrogen (N) and phosphorus (P) rates coupling with rational fertilization methodology could promote crop N accumulation, N use efficiency and yield production, particularly in semi-arid and arid regions. To test these characteristics, a two-year (2018 and 2019) pot experiment was therefore performed by growing summer maize in a rain-proof glass greenhouse, under 9 combined N (112, 150 and 187 kg ha-1, urea) and P (45, 60, 75 kg ha-1, calcium superphosphate) rates and three contrasting fertilizer placements. The fertilizers were placed by broadcast on soil surface (Broadcast), side band on 4 cm strip soil surface within 7 cm from sowing line (Side band) and deep band on 4 cm strip below 7 cm soil depth within 7 cm from sowing line (Deep band). Results from three maize growth stages (eight-leaf, 45 days after sowing, DAS; tasseling, 60 DAS; and harvest, 115 DAS) showed that leaf, stem, root N accumulation and total soil N were significantly increased under Deep band than under both Side band and Broadcast at N150P60, N187P60, N150P75 and N187P75, but not at N112P45, N150P45, N187P45, N112P60 and N112P75. Significantly greater leaf, stem, and root N accumulations were also displayed at N150 and N187 than at N112 for the same P60 or P75 under Deep band at 60 DAS and 115 DAS, while were for leaf and stem N accumulations at P75 and P60 than at P45 for the same N150 under Deep band at 45 DAS, 60 DAS and 115 DAS. Significantly greater agronomy N use efficiency, partial factor productivity and N use efficiency exhibited under Deep band than under Side band and Broadcast at N150P75 and N187P75, but at N150P60 and N187P60 for NUE only. In addition, leaf, stem, seed, root N concentrations positively correlated with their own N accumulations or soil N concentration at tasseling and harvest stages. Our results demonstrate that a synchronized N150P60, N187P60, N150P75 or N187P75 fertilization rate with Deep band placement can improve soil N availability and root N uptake, and hereby greater aboveground N accumulation, N use efficiency and yield production of maize particularly practical for small-holder farmers globally.

Currently, there is a tenacious need to find new ways to purify water by eliminating bacterial biofilms, textile dyes, and toxic water pollutants. These contaminants pose significant risks to both human health and the environment. To address this issue, in this study, we have developed an eco-friendly approach that involves synthesizing Cobalt-doped Cerium Iron Oxide (CCIO) nanocomposite (NC) using an aqueous extract of Gossypium arboreum L. stalks. The resulting nanoparticles can be used to effectively purify water and tackle the challenges associated with these harmful pollutants. Nanoparticles excel in water pollutant removal by providing high surface area for efficient adsorption, versatile design for simultaneous removal of multiple contaminants, catalytic properties for organic pollutant degradation, and magnetic features for easy separation, offering cost-effective and sustainable water treatment solutions. CCIO nanocomposite has been synthesized by green co-precipitation method due to biomolecules and co-enzymes present in the aqueous extract of Gossypium arboreum L. stalk; a single-step procedure completed in 5 h reaction time. Further, the synthesis of nanocomposites was confirmed by various characterization techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermogravimetric analysis (TGA), Dynamic light scattering (DLS), and Energy Dispersive X-Ray (EDX). CCIO NCs were discovered to have a spherical shape and an average size of 40 nm. Based on DLS zeta potential analysis, CCIO NCs were found to be anionic. Also, CCIO NCs showed significant antimicrobial and antioxidant activity. Overall, considering the physical and chemical properties, the application of CCIO NCs in the adsorption of various dyes (~91 %) and water pollutants (chromium = ~ 60 %) has been considered since they exhibit great adsorption capacity owing to their microporous structure which can be a step forward in water purification.

Abstract: Cancer cells are originated by normal cells and with those share the need to be fed. Metabolic reprogramming in cancer cells is not yet fully understood although there is a vast literature suggesting that huge amounts of both energy and substrates are require for synthesis of components of new neoplastic cells so that any macronutrient may be efficiently utilized. Recently, in vitro data show that EAA supplementation promoted colon cancer cells apoptosis by enhanced autophagy. Therefore, in this study we tested in vivo the effects of matched macronutrients standard laboratory diet (control) versus EAA rich modified diet (EAArmd) in mice injected with colon cancer cells. Results of the first set of 12 animals, 6 controls and 6 EAArmd-fed, showed that controls mice develop cancer volume cancers 5 times larger and heavier than EAArmd-fed. If confirmed, these results would open new scenarios for the cancer integrate therapies.

Lipofuscin is indigestible garbage that accumulates in the autophagic vesicles and cytosol of post-mitotic cells with age. Drs. Brunk and Terman postulated that lipofuscin accumulation is the main or at least a major driving factor in aging. They even posited that the evolution of memory is the reason why we get lipofuscin at all, as stable synaptic connections must be maintained over time, meaning that the somas of neurons must also remain in the same locale. In other words, they cannot dilute out their garbage over time through cell division. Mechanistically, their position certainly makes sense given that rendering a large percentage of a post-mitotic cell’s lysosomes useless must almost certainly negatively affect that cell and the surrounding microenvironment. It may be the case that lipofuscin accumulation is the main issue with regard to current age-related disease. Degradation in situ may be an insurmountable task currently. However, a method of systemic lipofuscin removal is discussed herein.

Nitrogen is crucial for plant physiology due to the fact that plants consume a significant amount of nitrogen during the development period. Nitrogen supports the root, leaf, stem, branch, shoot and fruit development of plants. At the same time, it also increases flowering. To monitor the vegetation nitrogen concentration, one of the best indicator developed in the literature is Normalized Difference Nitrogen Index (NDNI) which is based on the usage of the spectral bands: 1510 and 1680 nm. from Short-Wave Infrared (SWIR) region of electromagnetic spectrum. However, majority of the remote sensing sensors like cameras and/or satellites do not have a SWIR sensor due to the high costs. Many vegetation indexes like NDVI, EVI, MNLI, have been developed in also VNIR region to monitor the greenness and healthy of the crops. However these indexes are not very correlated to the nitrogen content. Therefore, in this study, a novel method is developed which transforms the estimated VNIR band indexes to NDNI by using a regression method between a group of VNIR indexes and NDNI. Training is employed by using VNIR band indexes as input and NDNI as output which are both calculated from the same location. After training, 0.93 correlation is achieved. Therefore, by using only VNIR band sensors, it is possible to estimate the nitrogen content of the plant with high accuracy.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

Plant N concentration (PNC) has been commonly used to guide farmers in assessing maize (Zea mays L.) N status and making in-season N fertilization decisions. However, PNC varies based on the development stage and therefore a relationship between biomass and N concentration is needed (i.e., critical N dilution curves; CNDC) to better understand when plants are N deficient. A few CNDC have been developed and used for plant N status diagnoses, but have not been tested in the US Midwest. The objective of this study was to evaluate under highly diverse soil and weather conditions in the US Midwest the performance of CNDCs developed in France and China for assessing maize N status. Maize N rate response trials were conducted across eight US Midwest states over three years. This analysis utilized plant and soil measurements at V9 and VT development stages and final grain yield. Results showed that the French CNDC (y=34.0x-0.37, where y is critical PNC, x is aboveground biomass) was better with a 91% N status classification accuracy compared to only 62% with the Chinese CNDC (y=36.5x-0.48). The N nutrition index (NNI), which is the quotient of the measured PNC and the calculated critical N concentration (Nc), based on the French CNDC was significantly related to soil nitrate-N content (R2=0.38-0.56). Relative grain yield on average reached a plateau at NNI values of 1.36 at V9 and 1.21 at VT, but for individual sites ranged from 0.80 to 1.41 at V9 and from 0.62 to 1.75 at VT. The NNI threshold values or ranges optimal for crop biomass production may not be optimal for grain yield production. It is concluded that the CNDC developed in France is suitable as a general diagnostic tool for assessing maize N status in US Midwest. However, the threshold values of NNI for diagnosing maize N status and guiding N applications vary significantly across the region, making it challenging for guiding specific on-farm N management. More studies are needed to determine how to effectively use CNDC to make in-season N recommendations in the US Midwest.

Inherent low soil fertility status limits productivity of rice in the lowland ecologies in Northern Ghana. Combining organic and inorganic N fertilizers could help to maintain the fertility of lowland soils for rice production. A screen house pot experiment was carried out to investigate the combined effect of biochar-compost and inorganic N fertilizer on the nitrogen uptake and agronomic performance of rice plants grown on Eutric Gleysol lowland soil. Inorganic N fertilizer alone and its combinations with different types of biochar-compost (based on the proportions of biochar and compost) were used as treatment. A control (unamended soil) was also included. The incorporation of biochar-compost and inorganic N fertilizer improved the growth parameters and yield components of rice plants. The combination of biochar-compost and inorganic nitrogen fertilizer was also found to improve nitrogen uptake and nutrient use efficiency (NUE) in rice plants. This practice could be the most likely viable option for alleviating lowlands soil fertility issues and increasing rice productivity in Northern Ghana.

Nanotechnology has become an increasingly promising medical field, particularly scar removal. Scar removal is a complex process involving regenerating damaged skin tissue, and nanotechnology presents unique solutions to this issue. One potential application of nanotechnology is using nanofibers as scaffolds to support the growth of new skin tissue. These fibres can also be loaded with drugs or growth factors to promote tissue regeneration and reduce scarring. Another potential application is nanocarriers for drug delivery to specific body areas, which can promote tissue regeneration and reduce scarring.Additionally, nanotechnology has been utilized to create new materials for skin regeneration, such as "nano skin" that mimics the structure of natural skin. Nanoprobes have also been developed for the detection of scar tissue and the monitoring of its progression. These potential nanotechnology applications offer exciting possibilities for the future of scar removal and skin repair. With further research and development, nanotechnology has the potential to revolutionize scar removal and provide more effective solutions for tissue regeneration.

Maize (Zea mays L.) is the most widely grown important crop in mid altitude areas of intensive maize-based cropping system of western Ethiopia. Agronomic management is the most important input for getting potential yield and high net returns in hybrid maize production. A field experiment was carried out on farmers’ field to find out the effect of varieties (four maize) and nitrogen fertilizer rate (55, 110 kg N ha-1) with one control on yield components and nitrogen use efficiency of different maize varieties in 2013 and 2014 cropping season. It was laid with randomized complete block design in factorial arrangement with three replications. Mean grain yield, thousand seed weight, dry biomass and harvest index of maize varieties were significantly differed among farms and varieties of maize. Application of nitrogen fertilizer rates was significantly increased mean grain yield maize varieties. Interaction of maize varieties with nitrogen fertilizer rates was significantly affected all yield components of maize varieties. Application half and full recommended nitrogen fertilizer gave mean grain yield advantages of 31 and 41 % over control maize varieties planted without nitrogen application. Maize varieties producing higher mean grain yield was also giving higher mean dry biomass. Mean nitrogen up take was varied from 225 to 357 kg ha-1 among varieties of maize. Higher agronomic efficiency of all maize varieties was obtained from maize planted with application half recommended nitrogen fertilizer compared to full recommend. Agronomic efficiency was ranged from 18 to 33 produced among maize varieties. Significantly higher nitrogen up take efficiency of maize varieties was achieved from maize planted with full recommended nitrogen fertilizer application. Considerably higher nitrogen use efficiency of maize varieties was realized from all maize varieties planted with application half recommended nitrogen fertilizer. Application of half recommended nitrogen fertilizer was gave 32 % fertilizer N use efficiency advantage as compared to full recommended nitrogen fertilizer. Maize varieties BH-661>BH-660> BH-543>BH-540>BH-140 were desirable varieties for further promotion work and use by smallholder farmers in mid altitude area of western Ethiopia.

Coal mining has caused a significant loss of nitrogen content of soil in mining areas. This article studies the effects of organic fertilizer, inorganic fertilizer, and combined application of Pseudomonas fluorescens with the ability of nitrogen fixation on soil nitrogen accumulation and composition in the reclamation area of Tunlan Coal Mine from 2016 to 2022 under the condition of equal nitrogen application, providing scientific basis for microbial fertilization and rapid increase of nitrogen content in the reclaimed soil of mining areas. The results showed that as the reclamation time increased, the nitrogen content and its composition structure of the soil treated with fertilization rapidly evolved towards normal farmland soil. The soil nitrogen content increased the fastest in the treatment of Pseudomonas fluorescens + organic fertilizer (MB), compared with inorganic fertilizer (CF), organic fertilizer (M), and Pseudomonas fluorescens + inorganic fertilizer (CFB) treatments, the treatment of Pseudomonas fluorescens + organic fertilizer (MB) can bring the total nitrogen (TN) content of the soil to normal farmland soil levels 1-3 years earlier. The comprehensive scores of Pseudomonas fluorescens + organic fertilizer (MB) and Pseudomonas fluorescens + inorganic fertilizer (CFB) on the two principal components were increased 1.58 and 0.79 than those of organic fertilizer (M) and inorganic fertilizer (CF) treatments, respectively. This further indicates that the combination of Pseudomonas fluorescens and organic fertilizer has a better effect on improving soil nitrogen accumulation than the combination of Pseudomonas fluorescens and inorganic fertilizer. At the same time, the application of Pseudomonas fluorescens will increase the content of unknown nitrogen (UN) in acid-hydrolysable nitrogen (AHN), and decrease the content of amino acid nitrogen (AAN) and ammonia nitrogen (AN), relatively. However, there was no significant effect on the content of ammonium nitrogen (NH4+-N) and nitrate nitrogen (NO3--N) in soil inorganic nitrogen (SMN). When combined with inorganic fertilizer, the contribution of soil mineralized nitrogen (SMN) to total nitrogen (TN) increased by 14.78%, while when combined with organic fertilizer, the contribution of acid-hydrolysable nitrogen (AHN) to total nitrogen (TN) increased by 44.77%. In summary, the use of Pseudomonas fluorescens is beneficial for nitrogen recovery in the reclaimed soil of coal mining areas. The optimal fertilization method under the experimental conditions is the combination of Pseudomonas fluorescens and organic fertilizer.

The article presents a technology for producing nitrogen-containing nanoporous biocarbon with high degree of elemental composition homogeneity, confirmed by electron spectroscopy. The research explores the relationship among the electronic characteristics of supramolecular nanoporous carbon, its porous structure, and the capacitance at its interface with the electrolyte. The obtained biocarbon is characterized by micro and mesopores, as evidenced by the results of studies by the method of nitrogen adsorption/desorption. The specific area of the available porous surface was found to be 1247 m2/g. Comparing this result with the data of small-angle X-ray scattering, we conclude that micropores are open while mesopores remain closed. This material was found to have a saturation magnetization σs of 1.4 A∙m2∙kg-1 and a coercive force Hc of 10 kA/m. The impedance studies of electrochemical cells of supercapacitors made of the experimental biocarbon were carried out. Equivalent electrical circuits of the studied electrochemical processes were constructed and characterized.

In this study, the literature on varnish contamination is investigated among the various con-taminations of lubricant. As the period of use of lubricant increases, the lubricant deteriorates and becomes contaminated. The varnish causes filter plugging, sticking of hydraulic valves and fuel injection pumps, obstruction of flow, reduction of clearance, poor heater and cooler perfor-mance, and increase of friction and wear in various lubrication systems. These problems also cause mechanical system failure, performance degradation, and increased maintenance and re-pair cost. To improve the problems causes by the varnish, an adequate understanding of varnish is required. Therefore, in this literature review, definitions and characteristics, generating ma-chinery, generating mechanisms, causes, measurement methods, and prevention or removal methods are summarized. Most of the data are reports of companies related to lubricant and machine maintenance, and are included in some papers. We hope that this summary of varnish will be helpful to those who are engaged in reducing or preventing varnish problems.

The potential of biological consortia designed for laccase production and dye treatment is discussed in this review. The poor yields in laccase production and low efficiency in dye decolorization of monoculture-based treatments has encouraged the use of designed biological consortia. A consortium is a system where the growth of two or more organisms, chosen to improve a particular bioprocess, is induced in the same medium. Chemical and natural mediators are being replaced by consortia for the production of laccases because, in addition to being less toxic, they induce new enzyme isoforms and lead to high laccase yields. On the other hand, consortia act synergistically in the decolorization of azo dyes through the enzymes they produce, so overall degradation is improved. Designed consortia are an attractive alternative still in development that could provide new biotechnological tools for the treatment of textile effluents.

The mosquito microbiota reduces the vector competence of Anopheles to Plasmodium and affects host fitness, it is therefore considered as a potential target to reduce malaria transmission. While immune induction, secretion of antimicrobials and metabolic competition are three typical mechanisms of microbiota-mediated protection against invasive pathogens in mammals, the involvement of metabolic competition or mutualism in mosquito-microbiota and microbiota-Plasmodium interactions has not been investigated. Here, we describe a metabolome analysis of the midgut of An. coluzzii provided with a sugar-meal or a blood-meal, under conventional or antibiotic-treated conditions. We observed that the antibiotic treatment affects the tricarboxylic acid cycle and nitrogen metabolism, notably resulting in decreased abundance of free amino acids. Linking our results with published data, we identified candidate pathways which may participate in microbiota/Plasmodium interactions via metabolic interactions or immune modulation.

Sombor index was recently defined in 2021 as a new vertex degree based topological index by Gutman and has received great attention of mathematicians and chemists. In this work, we determine how much the Sombor index is effected when we delete a vertex or an edge from a graph. Using the formulae obtained here successively, one can calculate the Sombor indices of large graphs by means of Sombor indices of smaller graphs which are obtained by deletion of vertices or edges.

Carbamazepine (CBZ) is one of the most common emerging contaminants released to the aquatic environment through domestic and pharmaceutical wastewater. Due to its high persistence through conventional degradation treatments, is considered a typical indicator for anthropogenic activities. This study tested the removal of CBZ through two different clay-based purification techniques: adsorption of relatively large concentrations (20-500 μmol L-1) and photocatalysis of lower concentrations (&lt;20 μmol L-1). The sorption mechanism was examined by FTIR measurements, exchangeable cations released, and colloidal charge of the adsorbing clay materials. Photocatalysis was performed in batch experiments under various conditions. Despite the neutral charge of carbamazepine, the highest adsorption was observed on negatively charged montmorillonite-based clays. Desorption tests indicate that adsorbed CBZ is not released by washing. The adsorption/desorption processes were confirmed by ATR-FTIR analysis of the clay-CBZ particles. A combination of synthetic montmorillonite or hectorite with low H2O2 concentrations under UVC irradiation exhibits efficient homo-heterogeneous photodegradation at μM CBZ levels. The two techniques presented in this study suggest solutions for both industrial and municipal wastewater, possibly enabling water reuse.

This work communicates laser-plasma experiments in a gaseous mixture of hydrogen and nitrogen. Time-resolved spectroscopy measures the first four Balmer series hydrogen lines together with selected neutral and ionized nitrogen lines. Optical breakdown plasma is generated in a 1:1 hydrogen:nitrogen mixture at ambient temperature and 0.27-atm pressure. Time-resolved spectroscopy records emitted radiation with spatial resolution along the slit height for the H_α, H_β, H_γ, and H_δ lines. For 13 selected time delays from 0.25 µs to 3.25 µs and 0.025 µ gate-widths, micro-plasma diagnostics is evaluated. Of interest are the peak-separation and width of H_δ and width of H_γ for electron densities in the range of 0.1 to 1.0×10¹⁷ cm^-3, and comparisons with H_β and H_α diagnostics. Integral inversions interrogate spatial distributions of the plasma expansion. Applications include laboratory and stellar astrophysics plasma diagnosis.

Irrigation and fertilization are indispensable links in the jujube planting industry in southern Xinjiang, China. However, the water and fertilizer integration effects on jujube growth and fruit quality remain unclear. A two-year water and fertilizer optimization coupling test was conducted to determine the optimal water- and nutrient-supply scheme. The three-factor randomized block experiment included water (W), nitrogen (N), and phosphorus (P). According to the principal component analysis of each index, each treatment’s comprehensive score was obtained. Using yield and economic regression models, the theoretical value and yield value of the optimal economic benefit are inferred. When W, N, and P were applied together, the fruit quality and yield of each treatment significantly differed, and the vitamin C, soluble sugar, and sugar–acid ratio increased significantly with an increase in nitrogen fertilizer. However, the titratable acid decreased. An increase in irrigation and nitrogen application significantly increased fruit yield. The comprehensive score was the highest in the N3P3W2 treatment, which improved fruit quality, and the lowest in the N4P3W2 treatment. When the amounts of N, P, and W were 275.56 kg·hm-2, 413.66 kg·hm-2, and 7278.19 m3·hm-2, respectively, the theoretical economic benefit was the best. The N4P3W2 treatment is the optimal treatment.

Conservation tillage and deep side-fertilization both hold the potential to reduce nitrogen leaching and improve grain yield and nitrogen use efficiency in fragrant rice cultivation practices. However, the combined impact of different tillage practices with deep side-fertilization on nitrogen leaching remains uncertain. Therefore, this study conducted on-site experiments for four rice growing seasons in both early and late seasons in 2018 and 2019, using the fragrant rice varieties "Meixiangzhan 2"(MX) and "Xiangyaxiangzhan"(XY). The four experimental treatments included:conventional tillage with regular fertilization (T1), conventional tillage with simultaneous deep fertilization (T2), reduced tillage with simultaneous deep fertilization (T3) , and no-tillage with simultaneous deep fertilization (T4). Our results indicate that the T4 treatment exhibited higher nitrogen leaching rates and potential nitrogen losses throughout the entire rice growth cycle, with a 4.51% increase in total nitrogen leaching and a 1.86% increase in potential nitrogen leaching compared to T1. In contrast, the T2 treatment demonstrated the lowest nitrogen leaching rate, resulting in a 6.01% reduction in total nitrogen leaching and a 9.57% decrease in potential nitrogen leaching compared to T1, demonstrating the most optimal performance. For MX, the T1 treatment resulted in lower daily grain outputs compared to the other treatments, with disparities ranging from 5.35% to 9.94%. Similarly, for the XY, the T1 treatment yielded significantly lower daily grain outputs compared to the other treatments, with discrepancies ranging from 6.26% to 10.81% during the late season of 2019. Overall, this study shows that conventional tillage with deep fertilization effectively reduces nitrogen leaching and boosts fragrant rice yields. Minimizing nitrogen leaching enhances nitrogen utilization efficiency. These insights highlight the significance of strategic fertilization and cultivation for environmental conservation and agricultural sustainability.

Empirical models help us understand the process of plant residue decomposition and nutrient release into the soil. The objective of this study was to determine an appropriate model to describe the decomposition of hairy vetch (Vicia villosa Roth) and cereal rye (Secale cereale L.) cover crop (CC) residue and nitrogen (N) release. Data pertaining to above and belowground CC residue mass loss and N release for up to 2633 cumulative decomposition degree days (112 d) after litterbag installation were obtained from two cropping system experiments, one conducted in 2015 and the other in 2017 and 2018 at the humid subtropical environment of southern IL, USA. Six exponential and two hyperbolic models were fit to percent mass and N remaining data to find the one with minimum Akaike Information Criterion (AIC) and residual sum of squares. Modified three-parameter single exponential and two- or three-parameter hyperbolic models best met the assumed criteria of selection for above and belowground CC residue, respectively. Fitting a double exponential model to a combined data for percent mass and N remaining, which identified two mass and N pools, a fast and a slow pool with different rate constants. A five-parameter double exponential with an asymptote met the preset criteria and passed all tests for normally distributed population, constant variance, and independence of residuals at α = 0.05 when fit to combined data of hairy vetch shoot mass and N remaining. However, a two-parameter hyperbolic and three-parameter asymptotic hyperbolic model provided the best fit to a combined data of cereal rye shoot mass and N remaining, respectively. Both hyperbolic decay models showed a good fit for belowground mass decomposition and N release for both CCs. Cereal rye had poorer fit than hairy vetch for mass and N remaining of both above and belowground mass. The best-selected decay models can be used to estimate the decomposition and N release rates of hairy vetch and cereal rye above and belowground residue in a similar environment.

Removal of hexavalent chromium had attracted much more attention as it was a hazardous contaminant. Electrochemical reduction technology was applied to removal chromium (VI) from wastewater. The mechanism and parameters affect the reduction process were investigated. The results showed that the reduction efficiency was significantly affected by the concentration of H2SO4, current density and reaction temperature. And the reduction efficiency was up to 86.45% at concentration of H2SO4 of 100g/L, reaction temperature of 70 ℃, current density at 50 A/m2, reaction time at 180 min and stirring rate of 500 rpm. The reduction process of chromium (VI) was followed pseudo-first-order equation, and the reduction rate could be expressed as Kobs = k [H2SO4]1• [j] 4•exp-4170/RT.

This review deals with the functionalization of double bonds carried out in the presence of a chiral catalyst exploiting the intramolecular attack to haliranium ions by nucleophilic nitrogen of amides or carbamates prepared from achiral aminoalkenes, and the C-N bonds formation leads to highly enantioenriched non-aromatic heterocycles. A range of protocols are reported, emphasizing the synthesis of many natural and biologically active products of pharmacological interest prepared according to this methodology.

Nitrogen is one of the most important macronutrients for crops, and in conjunction with artificial intelligence algorithms, it is possible to estimate it with the aid of vegetation indices through remote sensing. Various indices were calculated and those with a correlation ≥ 0.7 were selected for subsequent use in Random Forest, Gradient Boosting, and Artificial Neural Networks to determine their relationship with nitrogen levels measured in the laboratory. Random Forest showed no relationship, yielding an R2 of zero, whereas Artificial Neural Networks yielded the best results with an R2 of 0.93. Thus, it is reliable to estimate nitrogen levels using this algorithm by feeding it with data from TCARI, MCARI, TCARI/OSAVI, and MCARI/OSAVI, assisted by technological tools.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Microalgae are used in various biotechnological processes, such as biofuel production due to their high biomass yields, agriculture as biofertilizers, production of high-value-added products, de-contamination of wastewater, or as biological models for carbon sequestration. The number of these biotechnological applications is increasing, and as such, any advances that contribute to reducing costs and increasing economic profitability can have a significant impact. Nitrogen fixing organisms, often called diazotroph, also have great biotechnological potential, mainly in agri-culture as an alternative to chemical fertilizers. Microbial consortia typically perform more com-plex tasks than monocultures and can execute functions that are challenging or even impossible for individual strains or species. Interestingly, microalgae and diazotrophic organisms are capable to embrace different types of symbiotic associations. Certain corals and lichens exhibit this sym-biotic relationship in nature, which enhances their fitness. However, this relationship can also be artificially created in laboratory conditions with the objective of enhancing some of the biotech-nological processes that each organism carries out independently. As a result, the utilization of microalgae and diazotrophic organisms in consortia is garnering significant interest as a potential alternative for reducing production costs and increasing yields of microalgae biomass, as well as for producing derived products and serving biotechnological purposes. This review makes an effort to examine the associations of microalgae and diazotrophic organisms, with the aim of highlighting the potential of these associations in improving various biotechnological processes.

Pollution caused by copper is one of the key factors of environment contamination. As one of heavy metals, copper is hard to decompose in nature, the biological enrichment of which may lead to severe damage to health. Cu²⁺ detection, thus, possesses a bright application prospect both in environment protection and in human health. In this paper, a dual-functional fluorescence-magnetic composite nano-platform has been designed to sensitively detect, meanwhile capture and remove Cu²⁺ in the solution of water and ethanol (1:1, v/v). The core-shell structure nanoparticle synthesized by using Fe₃O₄ as core and SiO₂ as shell, is covalently bonded with rhodamine derivatives on the silica layer to construct the nano-platform. The emission is increased upon the addition of Cu²⁺, showing fluorescence turn on effect for the detection, and the limit of detection which was as low as 1.68 nM. Meanwhile, Cu²⁺ ions are captured by the coordination with rhodamine derivatives, and can be removable with the help of magnetic field.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

Nitrogen (N) is the most limiting nutrient for the production of vegetable crops, but anthropogenic sources pose risks due to its transformation into several reactive forms and movement throughout the environment. To mitigate the impact of environmental losses, current research efforts aim to improve management practices to obtain a greater Nutrient Use Efficiency (NUE). From a chemical, biological, and ecophysiological perspective, at a reductionist level we have acquired a considerable mechanistic understanding about the N cycle, the varied N chemical forms, microbial interactions and physiology of crop uptake. However, at a holistic level, we are far from obtaining an adequate understanding of the myriad of multi-level cropping system, genetic, socioeconomic, environmental, and ecological interactions that have an effect on the N cycle and NUE. Here, based on a selected review of the literature, we provide a perspective on the potentials to increase the NUE of vegetable crops, by adopting a range of best management practices and by highlighting some of the N x system interactions that may be considered to better understand the complex dynamics of the N cycle, to optimize the NUE of vegetable crops, and to explore alternatives to the reliance on the use of synthetic N sources.

Although jojoba (Simmondsia chinensis) has been cultivated for years, information on its N re-quirements is limited. A 6-year study of mature jojoba plants grown under field conditions with an intensive management regime evaluated the effect of N-application rate on plant nutrient status, growth and productivity, and nitrate accumulation in the soil. Five levels of N application were tested: 50, 150, 250, 370 and 500 kg N ha-1. The fertilizers were provided all along the growing season via subsurface drip irrigation system. Leaf N concentration, in both spring and summer, reflected the level of N applied. Diagnostic leaf (youngest leaf that has reached full size) concentration of 1.3% N was identified as the threshold for N deficiency. Increasing rates of N application resulted in higher P levels in young leaves. Plant K status, as reflected by leaf analysis, was not affected by N treatment but was strongly affected by fruit load. Vegetative growth was inhibited when only 50 kg N ha-1 was applied. Soil analysis at the end of the fertilization season showed substantial accumulation of nitrate for the two highest application rates. Considering productivity, N costs, and environmental risk, 150 kg N ha-1 is the recommended dosage for in-tensively grown jojoba. N deficiencies can be identified using leaf analysis and excess N can be detected by soil sampling toward the end of the growing season. These results and tools will fa-cilitate precise N fertilization in intensive jojoba plantations.

Shrubs are a significant component of urban vegetation residing in parks, but they experience various influences of biotic and abiotic agents, among which aphids play an important role. In this work, the effect of aphid colonization on three shrub species in urban environment was examined. Fourteen parameters have been analyzed, describing photosynthetic pigment content and gas exchange to carbon, nitrogen, and hydrogen partition. While no significant effect of colonization was found on photosynthetic pigment parameters, the effect was significant on gas exchange parameters. The strongest effect aphid colonization achieved on nitrogen partition and C/N ratio, parameters that could be suggested in further similar studies. All parameters were classified in two groups according to principal component analysis, suggesting correlation between nitrogen and carbon content, C/N ratio, measured gas exchange parameters and chlorophyll a content. The ratio between net photosynthesis and dark respiration (A/K) was in the second group, suggesting that this parameter provide additional information on the effect of aphid colonization, and deserve special attention in further studies. There were differences in reaction of examined shrub species, where the strongest reaction by gross primary productivity (GPP) achieved Hybiscus syriacus, and by nitrogen partition and C/N ratio Spirea trilobata and Cydonia japonica.

Rice production is a significant contributor to methane emissions, accounting for ap-proximately 11% of global anthropogenic emissions. However, methane emissions in rice fields could effectively be reduced by implementing proper management practices and careful cultivar selection. The impact of nitrogen fertilizers on methane emissions is mul-tifaceted, as these fertilizers enhance crop growth and influence the activity of me-thane-producing (methanogens) and methane-consuming microbes (methanotrophs), leading to complex outcomes in methane emissions. In this study, we used qPCR to quan-tify methanogens and methanotrophs using mcrA (methanogenesis-related gene) and pmoA (methane oxidation-related gene) primer sets under different nitrogen levels (0, 50, and 100%) and rice varieties. The results revealed that higher nitrogen input led to higher methanogen inhabitation in the rhizosphere. Additionally, the abundances of methano-gens and methanotrophs varied among the different rice varieties. Furthermore, it was observed that there may be an additive effect between the rice variety and nitrogen level used. These findings suggest that future breeding efforts should involve screening for me-thane-related microbes in rice cultivars adapted to low-nitrogen conditions. By identifying and selecting rice varieties that promote lower methanogen levels and higher metha-notroph inhabitation, significant steps can be taken to mitigate greenhouse gas emissions from rice cultivation.

Abstract: Rice production is a significant contributor to methane emissions, accounting for approximately 11% of global anthropogenic emissions. However, there is potential for effectively reducing methane emissions from rice fields through the implementation of proper management practices and careful cultivar selection. The impact of nitrogen (N) fertilizers on methane (CH4) emissions is multifaceted, as these fertilizers not only en-hance crop growth but also influence the activity of methane-producing microbes (Meth-anogens) and methane-consuming microbes (Methanotrophs), leading to complex out-comes in CH4 emissions. In this study, we utilized qPCR to quantify methanogens and methanotrophs using mcrA (methanogenesis-related gene) and pmoA (methane oxida-tion-related gene) primer sets under different nitrogen levels (0, 50, 100%) and rice varie-ties. The results revealed that higher nitrogen inputs led to higher methanogen inhabita-tion in the rhizosphere. Additionally, the abundances of methanogens and metha-notrophs varied among different rice varieties. Furthermore, through the analysis of two-way ANOVA, it was observed that there may be an additive effect between rice variety and nitrogen level. Furthermore, enhancing agronomic traits related to yield can reduce methanogen inhabitation. These findings suggest that future breeding efforts should in-volve the screening of methane-related microbes in rice cultivars adapted to low nitrogen conditions. By identifying and selecting rice varieties that promote lower methanogen lev-els and higher methanotroph inhabitation, we can take significant steps towards mitigating greenhouse gas emissions from rice cultivation.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

Particulate matter is a severe source of atmospheric pollution in urban cities, and it has adverse effects on human health. This study was conducted during the whole year of 2016 to monitor the concentrations of PM₁₀ and PM_2.5 on the Beijing Hanshiqiao wetland and bare land in Beijing to analyze their correlations with meteorological factors and compare the removal efficiency between two land surface types. The results indicated that (1) the PM₁₀ and PM_2.5 concentrations on the bare land were higher than those on wetland as a whole, reaching the highest value both at night and dusk and the lowest value near noon. The average concentration of PM₁₀ was higher in winter (wetland: 137.48 μg·m^-3; bare land: 164.75 μg·m^-3) and spring (wetland: 205.18 μg·m^-3; bare land: 244.85 μg·m^-3) and the concentration of PM_2.5 on the wetland also reached the higher value in winter and spring with the average of 84.52 μg·m^-3 and 98.98 μg·m^-3, whereas, it was higher in spring and summer on the bare land; (2) concentrations of PM₁₀ and PM_2.5 were significantly positively affected by the relative humidity (P < 0.01) and negatively influenced by wind speed (P < 0.05). The relationship between PM₁₀ and PM_2.5 concentrations and temperature was found complicated: it showed a significantly negative correlation (P < 0.01) in winter and spring and was insignificant in autumn, but in summer, only the correlation between the PM₁₀ concentration and temperature on wetland was significant (P < 0.01); (3) the removal efficiencies of PM₁₀ and PM_2.5 followed the order of spring > winter > autumn > summer on the wetland, and the removal efficiency of PM₁₀ was greater than that of PM_2.5. This study is aim to provide practical measures to improve the air quality and facilitate sustainable development in Beijing.

The spread of micro- (MPs) and nanoplastics (NPs) in the environment has become a significant environmental concern, necessitating effective removal strategies. In this comprehensive scientific review, we examine the use of magnetic nanoparticles (MNPs) as a promising technology for the removal of MPs and NPs from water. We first describe the issue of MPs and NPs and their impact on the environment and human health. Then the fundamental principles of using MNPs for the removal of these pollutants will be presented, emphasizing that MNPs enable selective binding and separation of MPs and NPs from water sources. Furthermore, we provide a short summary of various types of MNPs that have proven effective in the removal of MPs and NPs. These include ferromagnetic nanoparticles, MNPs coated with organic polymers, as well as nanocomposites and magnetic nanostructures. We also review their properties, such as magnetic saturation, size, shape, surface functionalization and stability, and their influence on removal efficiency. Next, we describe different methods of utilizing MNPs for the removal of MPs and NPs. We discuss their advantages, limitations, and potential for further development in detail. In the final part of the review, we provide an overview of existing studies and results demonstrating the effectiveness of using MNPs for the removal of MPs and NPs from water. We also address challenges that need to be overcome, such as nanoparticle optimization, process scalability, and the removal and recycling of nanoparticles after the completion of the process. This comprehensive scientific review offers an extensive insight into the use of MNPs for the removal of MPs and NPs from water. With improved understanding and the development of advanced materials and methods, this technology can play a crucial role in addressing the issue of MPs and NPs and preserving a clean and healthy environment.

Composite membranes formed by sulfonated poly(ether ether ketone) (SPEEK) with embedded carbon quantum dots (CQDs) were used for detection and removal of heavy metal ions, such as lead and cadmium, from water. SPEEK is responsible for the capture of heavy metals based on the cation exchange mechanism, while CQDs detect their contamination by exhibiting changes in fluorescence. Water-insoluble “red” carbon quantum dots (rCQDs) were synthesized from p-phenylenediamine so that their photoluminescence was shifted from that of the polymer matrix. CQDs and the composites were characterized by several techniques: FTIR, Raman, UV/VIS, photoluminescence, XPS spectroscopies and AFM microscopy. The heavy metal ion concentration was analyzed by inductively coupled plasma–optical emission spectroscopy (ICP-OES). The concentration ranges were 10.8 - 0.1 mM for Pb2+ and 10.0 - 0.27 mM for Cd2+. The composite achieved 100% removal efficiency for lead and cadmium if the concentration was below a half of the ion exchange capacity of SPEEK. The regeneration of membranes in 1 M NaCl was also studied. SPEEK/rCQDs showed a turn-off effect more pronounced for lead. A second order law was effective to describe the kinetics of the process.

Bioelectric effect is known as combinatorial biofilm treatment with low dose of antibiotics with small electricity. When external electric field or current are applied, biofilms can be affected by the electrostatic force, non-uniform distribution of essential electrolytes, induction of low activity of enzyme, and increase of permeability of biofilms. In this work, we have focused on the reduction of applied electric power consumption that could avoid water electrolysis which was one of major challenges for biomedical applications. We have developed a new type of electrical signal that enhances the efficacy of biofilm removal. The results show combination of alternating and direct current remove biofilm effectively without causing electrolysis. We further developed an oral healthcare device as a bioelectric toothbrush and tested in dental clinic. The results demonstrated 75% reduction of gingivitis. In addition, we have tested a mimicked air conditioner biofilms that are root causes of aerobic hygiene infection. The result demonstrates 81.8% increased biofilm removal. In conclusion, a new bioelectric technology has been developed and demonstrated the biofilm removal efficacy without the electrolysis.

Deep convolutional neural network (CNN) has shown their great advantages in the single image deraining task. However, most existing CNN-based single image deraining methods still suffer from residual rain streaks and details lost. In this paper, we propose a deep neural network including the Multi-scale feature extraction module and the channel attention module, which are embed in the feature extraction sub-network and the rain removal sub-network respectively. In the feature extraction sub-network, the Multi-scale feature extraction module is constructed by a Multi-layer Laplacian pyramid, and is then integrated multi-scale feature maps by a feature fusion module. In the rain removal sub-network, the channel attention module, which assigns different weights to the different channels, is introduced for preserving image details. Experimental results on visually and quantitatively comparison demonstrate that the proposed method performs favorably against other state-of-the-art approaches

The original purpose of this article was to modify the original SIR equations to allow for a direct source of infection (without which the original equations would have no solutions unless one starts with an already infected population) and also to see to what extent one could obtain multiple outbreaks of an infectious disease. In the course of developing the basic ideas several other factors arose to take prominent roles.Perhaps one of the more salient factors is the point that choosing an arbitrary time to change conditions from say a lock-down for the population to a less stringent social behavior, such as allowing partial or complete opening of businesses and schools, etc. should be based on knowledge of the disease and its evolution. Such decisions are usually made by politicians who have less than full information concerning the consequences of their actions. Several examples are given to illustrate these points.

Anthropogenic lead pollution is an environmental problem that threatens the quality of soils and waters and endangers living organisms in numerous surface and subsurface habitats. Lead coprecipitation on mineral surfaces through dissolution-recrystallization processes has long term effects on lead bioavailability. Gypsum and calcite are among the most abundant and reactive rock forming minerals present in numerous geological settings. In this work, we study the interaction of slightly acidic (pHi = 5.5) Pb-bearing aqueous solutions ([Pb]i = 1 mM and 10 mM) with crystals of gypsum and /or calcite under atmospheric conditions. This interaction results in a reduction of the concentration of lead in the liquid phase due to the precipitation of newly formed Pb-bearing solid phases. The extent of this Pb removal mainly depends on the nature of the primary mineral phase involved in the interaction. Thus, when gypsum is the only solid phase initially present in the system the Pb-bearing liquid-gypsum interaction results in Pb removals in the 98-99.8 % range, regardless of [Pb]i. In contrast, when the interaction takes place with calcite, Pb removal strongly depends on [Pb]i. It reaches 99% when [Pb]i = 1 mM while it is much more modest (⁓13%) when [Pb]i = 10 mM. Interestingly, Pb-removal is maximized for both [Pb]i (99.9 % for solutions with [Pb]i = 10 mM and 99.7% for solutions with [Pb]i = 1 mM) when Pb-polluted solutions simultaneously interact with gypsum and calcite crystals. Despite the large Pb removals found in most of the cases studied, the final Pb concentration ([Pb]f) in the liquid phase always is well above the maximum permitted in drinking water (0.1 ppm), with the minimum ([Pb]f = 0.7 ppm) being obtained for solutions with [Pb]i =1 mM after their interaction with mixtures of gypsum and calcite crystals. This result suggests that integrating the use of mixtures of gypsum-calcite crystals might help to develop more efficient strategies for in-situ decontaminating Pb-polluted waters through mineral coprecipitation processes.

Urban stormwater runoff is a significant source of pollutants into surface water bodies. One such pollutant, 1H-benzotriazole, is a persistent, recalcitrant trace organic contaminant commonly used as a corrosion inhibitor in airplane deicing processes, automobile liquids, and engine coolants. This study explored the removal of 1H-benzotriazole from stormwater using bench-scale biofilter mesocosms planted with California native sedge, Carex praegracilis, over a series of three storm events and monitoring period. Benzotriazole metabolites glycosylated benzotriazole and benzotriazole alanine were detected and benzotriazole and glycosylated benzotriazole partitioning in the system were quantified. With a treatment length of seven days, 97.1% of benzotriazole was removed from stormwater effluent from vegetated biofilter mesocosms. Significant concentrations of benzotriazole and glycosylated benzotriazole were observed in the C. praegracilis leaf and root tissue. Additionally, a significant missing sink of benzotriazole developed in the vegetated biofilter mesocosms. This study suggests that vegetation may increase the operating lifespan of bioretention basins by enhancing degradation of dissolved trace organic contaminants, thus increasing the sorption capacity of the geomedia.

Heterocycles are unique precursors for the synthesis of various pharmaceuticals and agrochemicals particularly those possessing N- or O- moieties. The development of methods to prepare heterocycles is of great importance in synthesis of organic compounds, especially the heterocycles which can be found in natural products. The synthesis of nitrogen and oxygen containing heterocycles viz. coumarins, dihydropyrimidinones, imidazoles, isoxazoles and benzimidazoles represented an attractive and demanding work for chemists as these nucleus has found extensive applications in several fields such as material science, analytical chemistry and most importantly in medicinal chemistry. Organic synthesis has been attracted towards the development of new environmental friendly procedures to achieve the goals of green chemistry. The fundamental aspects of green chemistry are use of biocatalysts and environmental benign solvents under mild conditions. The present review article summarized the green synthetic methods and biological activities of nitrogen and oxygen containing heterocycles.

Biological nitrogen fixation (BNF) by symbiotic bacteria plays a vital role in sustainable agriculture. However, current quantification methods are often expensive and impractical. This study explores the potential of Raman spectroscopy, a non-invasive technique, for rapid assessment of BNF activity in soybeans. Raman spectra were obtained from soybean plants grown with and without rhizobia bacteria to identify spectral signatures associated with BNF. δN15 isotope ratio mass spectrometry (IRMS) was used to determine actual BNF percentages. Partial least squares regression (PLSR) was employed to develop a model for BNF quantification based on Raman spectra. The model explained 80% of the variation in BNF activity. To enhance the model's specificity for BNF detection regardless of nitrogen availability, a subsequent elastic net (Enet) regularization strategy was implemented. This approach provided insights into key wavenumbers and biochemicals associated with BNF in soybeans.

Chloride (Cl-) is applied in coffee in rates as a “macronutrient” due that potassium (K+) is one of the most demanded nutrients by the coffee plant, and the potassium muriate (KCl) bases fertilizer is one the most used by the coffee growers. Does not exist scientific evidence that addresses the question regarding with which is the influences of the Cl- applied in the K fertilization base on MOP on coffee growth, nutrient uptake, and nitrogen use efficiency (NUE). Over four years, two trials were conducted on greenhouse and field conditions to address these questions. The trials set up were designed to test the influence of increased Cl- and reduced S rates on biomass accumulation, nutrient uptake, and NUE. A significant effect of the Cl- rates on growth was observed under greenhouse conditions but a non-significant effect on yield under field conditions. Cl- and S significantly influence the NUE in coffee. The result allows us to conclude that Cl- rates need to be balanced with S rates and that Cl- applied as a macronutrient can improve the NUE in coffee when those rates do not exceed 180 mg. L-1 Cl- and 80 mg.L-1 S in the greenhouse and 150 kg.ha-1.year-1 Cl- and 50 kg. ha-1.year-1 S in field conditions. In practical terms, coffee farmers need to balance the K base fertilizers sources to improve the nutrient use efficiency, especially the NUE.

A complex square matrix $A$ is said to be Hermitian if $A= A^{\ast}$, the conjugate transpose of $A$. The topic of the present note is concerned with the characterization of Hermitian matrix. In this note, the we show that each of the two triple matrix product equalities $AA^{\ast}A = A^{\ast}AA^{\ast}$ and $A^3 = AA^{\ast}A$ implies that $A$ is Hermitian by means of decompositions and determinants of matrices, which are named the two-sided removal and cancellation laws associated with Hermitian matrix, respectively. We also present several general removal and cancellation laws as the extensions of the preceding two facts about Hermitian matrix.

The brain's unique characteristics make it exceptionally susceptible to oxidative stress, which arises from an imbalance between reactive oxygen species (ROS) production, reactive nitrogen species (RNS) production, and antioxidant defense mechanisms. This review explores the factors contributing to the brain vascular tone vulnerability in the presence of oxidative damage, which can be of clinical interest in critically ill patients or presenting acute brain injuries. The brain's high metabolic rate and inefficient electron transport chain in mitochondria lead to significant ROS generation. Moreover, non-replicating neuronal cells and low repair capacity increase susceptibility to oxidative insult. ROS can influence cerebral vascular tone and permeability, with a potential impact on cerebral autoregulation. Different ROS species, including superoxide and hydrogen peroxide, exhibit vasodilatory or vasoconstrictive effects on cerebral blood vessels. Reactive nitrogen species (RNS), particularly NO and peroxynitrite, also exert vasoactive effects. This review further investigates the neuroprotective effects of antioxidants, including superoxide dismutase (SOD), vitamin C, vitamin E, and the glutathione redox system. Various studies suggest that these antioxidants could be used as adjunct therapies to protect the cerebral vascular tone during high oxidative stress conditions. Nevertheless, more extensive research is required to comprehensively grasp the relationship between oxidative stress and cerebrovascular tone, as well as to explore the potential benefits of antioxidants as adjunctive therapies in critical illnesses and acute brain injuries.

The aims of study was to evaluate the effects of rates, sources and timing of nitrogen application under cover of transgenic corn yield cultivated in Amazon Biome. The experiments were conducted in Parauapebas city, State of Pará, Brazil, in two years (2016/2017 and 2017/2018). The experimental design was randomized blocks, in a 5x2x2 factorial scheme, consisting of five rates of N (0; 45; 90; 135; and 180 kg ha-1), two nitrogen sources (urea and ammonium sulfate) and two application times of N (phenological stages V4 and V8), with four replications. The factor N rates promoted adjustment of linear equation (leaf area index, mass of thousand grains, and yield) and quadratic equation (dry mass of leaf index). Nitrogen fertilization promoted significant increases in mass of thousand grains and yield, obtaining the best results with 180 kg ha-1 of N applied at V4 phenological stage. Based on results obtained in two years of corn cultivated under conditions of Amazon Biome, the application of N at V4 phenological stage at rates of 121 to 131.39 kg ha-1 of N showed the best results for vegetative growth, while 180 kg ha-1 of N, regardless of source used, urea or ammonium sulfate, promoted greater grain weight and greater yield.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

Forty-five of intact three sheep breeds (Awassi, Harri, and Najdi) were used in this study (15 animals of each breed), with weight ranged from 23.40 to 25.87 kg. Five animals from each group at the end of growth trial were used for digestibility and nitrogen balance trials. The three groups of sheep had effect (p > 0.05) in the final live weight (FLW). Average daily feed intake (ADI), average daily gain (ADG) and feed conversion ratio (FCR) were significantly (p < 0.05) different among the three groups. For digestibility coefficients, the three breeds of sheep had no effect (p > 0.05) in dry matter (DM), organic matter (OM), crude protein (CP), crude fiber (CF), nitrogen free extract (NFE), neutral detergent fiber (NDF) and acid detergent fiber (ADF). In the similar approach, no significant differences were founds among three breeds of sheep in digestible organic matter, digestible of crude protein, total digestible nutrients and nitrogen retention. The current study concluded that the sheep breeds affected average daily feed intake, average daily gain and feed conversion ratio (FCR). Awassi breed showed the best of average daily gain and feed conversion ratio followed by Najdi then Harri breeds. The breed of sheep had no effect on digestibility coefficients and nitrogen retention.

Many studies have found that future predicted CO2 levels (< 800 ppm) can increase plant mass but dilute N content in leaves, impacting antiherbivore compounds. Nitrogen-fixing plants may balance leaf C:N ratio under elevated CO2, counteracting this dilution effect. The aim of this study was to look at how nitrogen-fixing plants grow and respond to herbivore damage at different CO2 levels. Alnus incana ssp. rugosa was grown at 400, 800, or 1600 ppm CO2 in soil collected from the field, inoculated with Frankia and exposed to herbivores (Orgyia leucostigma). Elevated CO2 increased nodulated plant biomass and stimulated the nitrogen fixation rate in the early growth stage. However, nitrogen-fixing plants were not able to balance the C:N ratio under elevated CO2 after grown 19 weeks. When plant were grown at 400 and 1600 ppm CO2, herbivores preferred to feed on leaves of nodulated plants. At 800 ppm CO2, nodulated plants accumulated more total phenolic compounds in response to herbivore damage than plants in the non-Frankia and non-herbivore treatments. Our results suggest that plant leaf defence, not leaf nutritional content, is the dominant driver of herbivory and nitrogen fixing plants have limited ability to balance C:N ratios at elevated CO2 in natural soil.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T1 = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T2 = 50 kg N ha^-1, T3 = 100 kg N ha^-1 and T4 = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T5: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T6: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T7: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO2 concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T6 = Split N100) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

This review describes how resonance in amides is greatly affected upon substitution at nitrogen by two electronegative atoms. Nitrogen becomes strongly pyramidal and resonance stabilisation, evaluated computationally, can be reduced to as little as 50% that of N,N-dimethylacetamide. However, this occurs without significant twisting about the amide bond, which is borne out both experimentally and theoretically. In certain configurations, reduced resonance and pronounced anomeric effects between heteroatom substituents are instrumental in driving the HERON (Heteroatom Rearrangement On Nitrogen)^† reaction, in which the more electronegative atom migrates from nitrogen to the carbonyl carbon in concert with heterolysis of the amide bond, to generate acyl derivatives and heteroatom-substituted nitrenes. In other cases the anomeric effect facilitates S­_N1 and S_N2 reactivity at the amide nitrogen.

Microporous organic polymers (MOPs) are promising materials for gas sorption because of the intrinsic and permanent porosity, designable framework and low density. The introduction of nitrogen-rich building block in MOPs will greatly enhance the gas sorption capacity. Here, we report the synthesis of MOPs from the 2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine unit and aromatic azides linkers via click polymerization reaction. FTIR and solid state 13C CP-MAS NMR confirm the formation of the polymers. CMOP-1 and CMOP-2 exhibit microporous networks with BET surface area of 431 and 406 m2 g-1 and narrow pore size distribution under 1.2 nm. Gas sorption isotherms including CO2 and H2 were measured. CMOP-1 stores superior CO2 level of 8.2 wt% (1.88 mmol g-1) at 273 K/1.0 bar and H2 uptake up to 0.6 wt% at 77 K/1.0 bar, while CMOP-2 with smaller surface area shows lower CO2 adsorption capacity of 7.3 wt% (1.66 mmol g-1) and H2 uptake (0.5 wt%). In addition, I2 vapor adsorption was tested at 353 K. CMOP-1 shows higher gravimetric load of 160 wt%. Despite of the moderate surface area, the CMOPs display excellent sorption ability for CO2 and I2 due to the nitrogen-rich content in the polymers.

A ganglion cyst is a benign fluid-filled sac that typically appears on the dorsal aspect of the wrist, arising idiopathically near the joint capsule or tendon sheath. Diagnosis is primarily clinical, with MRI and ultrasound serving as confirmation tools. Treatment options range from immobilization, aspiration, hydrossection, steroid or hyaluronidase injection, to surgical intervention. Although relatively uncommon, Dorsal Ganglion Cysts (DGC) can lead to Dorsal Wrist Impingement (DWI) syndrome. This syndrome results from the thickening of the wrist capsule due to overuse, injury, or repetitive activities. This thickening can lead to the compression of the extensor carpi radialis brevis (ECRB) tendon during wrist extension and produce tenderness around the lunate. In some refractory cases, MRI findings may show recurrent ganglion cysts, while in others, they may appear "normal." Consequently, the diagnosis remains clinical, and imaging is primarily employed to rule out secondary causes. Management strategies encompass rest, immobilization, occupational therapy, non-steroidal anti-inflammatory drugs (NSAIDs), cortisone injections, and, in certain instances, surgical intervention. Despite the clinical significance of these conditions, limited studies have explored their interrelationship. In this context, we present a rare case involving a 23-year-old female with recurrent DGC accompanied by DWI syndrome. Initially, the patient reported idiopathic left dorsal wrist pain localized around the tendon sheath. Her initial X-ray did not reveal any abnormalities, but MRI identified two ganglion cysts. A series of treatments were initiated, including left tendon sheath hydrossection, corticosteroid injections into the left wrist, and the excision of ganglion cysts from the left wrist. Furthermore, occupational therapy, oral Meloxicam, and Voltaren gel treatments were integrated into the management plan. Subsequent imaging confirmed the resolution of the cysts and an overall enhancement in the range of motion and wrist strength. However, the patient experienced only minimal pain relief, and pain was still elicited during end-range wrist extension and upon dorsal wrist palpation. An electromyography (EMG) test ordered to rule out neuropathic causes did not yield any conclusive results. Nonetheless, a repeat X-ray revealed mild soft tissue swelling on the dorsal side of the wrist, and a follow-up MRI detected ganglion cysts on the dorsal aspect of the lunate and the ECRB tendons. These findings indicated a re-accumulation of dorsal ganglion cysts with a concurrent dorsal impingement syndrome component. Consequently, the patient was referred to an orthopedic surgeon for evaluation and potential revision surgery. This unique case underscores the possibility of developing DWI Syndrome after the removal of a DGC. The diagnosis of this syndrome can be elusive, particularly when X-rays, MRIs, and EMGs yield negative results. Trauma, such as repeated hand surgery or recurrent ganglion cysts, may exacerbate wrist pain despite improvements in range of motion and strength. Special consideration should be given to patients who undergo surgical cyst excisions, as this procedure heightens the risk of recurrence and can irritate the tendon sheath. Collaborative efforts between Physical Medicine and Rehabilitation (PM&amp;R), Occupational Therapy (OT), and surgical teams may play a pivotal role in managing pain associated with these conditions. We propose that future research endeavors should focus on establishing guidelines for the management of this unique condition.

The adsorption of actinide ions (Am(III) and U(VI)) from aqueous solutions by pristine and oxidized carbon fabrics has been investigated by means of batch experiments at different pH values (4, 7 and 9) and temperatures (25, 35 and 45 °C) under ambient atmospheric conditions. The experimental results indicate that both pH and fabric texture affect the adsorption rate and the relative removal efficiency, which results at 70% and 100% for Am(III) and U(VI), respectively. The Kd (L/kg) values for U(VI) have been generally found to be higher (2 &lt; log10(Kd)&lt; 3) than the corresponding values for the Am(III) adsorption (1.5 &lt; log10(Kd) &lt; 2). The data obtained from the experiments regarding the temperature effect imply that the relative adsorption for both actinides increases with temperature and that the adsorption is an endothermic and entropy-driven reaction. Application of the fabrics to remove the two actinides from contaminated seawater samples shows that both the relative removal efficiency and the Kd values decrease significantly due to the presence of competitive cations (e.g., Ca2+ and Fe3+) and complexing anions (CO32-) in the respective waters. Nevertheless, the removal efficiency is still remarkable (50% and 90% for Am(III) and U(VI), respectively), demonstrating that these materials could be attractive candidates for the treatment of radionuclide/actinide contaminated waters.

Space debris, which includes retired satellites, used rocket stages, and explosion- or collision-related bits, poses a serious threat to both ongoing and future space activity. Addressing the problem of space debris has become essential for the sustainability of space operations due to the exponential development in satellite deployments and space research. The development of technology and tactics aimed at reducing the debris problem and assuring a cleaner cosmos are the main topics of this abstract, which provides an outline of the idea of sustainable space debris management and removal. The paper opens by outlining the history of space debris and the major difficulties caused by space debris, such as the dangers to functioning satellites, the possibility of catastrophic collisions, and the production of more debris as a result of cascade occurrences. The paper then emphasized the guidelines of space debris mitigation. It emphasizes the pressing requirement for long-term fixes that tackle the issue at its root. The paper then discusses different methods for managing space debris, such as proactive measures, active debris removal (ADR). It talks about how important it is to use sustainable methods during every stage of a space mission's lifecycle, from design and operation to deorbiting and disposal. This paper concludes with a summary of sustainable space debris removal, noting the difficulties caused by debris and the demand for all-encompassing approaches and technology to address this issue. It emphasizes how crucial global collaboration, technological development, and institutional frameworks are to creating a sustainable and debris-free space environment.

Effective oral care is a critical requirement to maintain high quality of life. Most oral diseases are caused by plaque (oral biofilm), which is also correlated with systemic diseases. A common method to remove biofilm is brushing teeth with a toothpaste. However, 3.5 billion people in the world have oral diseases, meaning that more efficient methods of removing biofilms are needed. We have developed a toothbrush applying bioelectric effect (BE) utilizing an electric force for biofilm removal. It demonstrated significantly higher biofilm removal efficiency than non-BE manual toothbrushes. Tests were performed in saline and toothpaste conditions using various pressure. Results showed that the BE toothbrush had a significantly higher biofilm removal efficiency in saline (0.5 N: 215.43 ± 89.92 %, 2.5 N: 116.77 ± 47.02 %) and in a toothpaste slurry (0.5 N: 104.96 ± 98.93 %, 2.5 N: 96.23 ± 35.16 %) than non-BE manual toothbrushes. Results also showed that BE toothbrushes were less dependent on toothpaste. This study suggests that the application of BE can be a new solution to plaque problems in oral care.

The peculiar physicochemical features of deep eutectic solvents (DESs), in particular their tunability, make them ideal media for various applications. Despite their ability to solubilize metal oxides, their use as rust removers from valuable substrates has not yet been thoroughly investigated. In this study we chosen three known DESs, consisting of choline chloride and acetic, oxalic or citric acid for evaluating their ability to remove corrosion products from a cellulose-based material as linen fabric and two different lithotypes, as travertine and granite. The artificial staining was achieved by placing a rusty iron grid on their surfaces. The DESs were applied by means of cellulose poultice on the linen fabrics, while on the rusted stone surfaces with a cotton swab. Macro- and microscopic observations, colorimetry and SEM/EDS analysis were employed to ascertain the cleaning effectiveness and the absence of side effects on the samples after treatment. Oxalic acid-based DES was capable of removing rust stains from both stone and cellulose-based samples, while choline chloride/citric acid DES was effective only on stone specimens. The results suggest a new practical application of DESs for the elimination of rust from lithic and cellulosic substrates of precious and artistic value.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

Adsorption is an effective strategy for the removal of pollutants from the wastewater. Herein, a 2-hydroxyterephthalic acid (HTC) modified hypercrosslinked polymer (HTC-HCP) is successfully synthesized via Friedel-Crafts reactions, and used as an adsorbent for the different types of pollutants including organic contaminants and heavy metal ions from wastewater. Excellent adsorption capacities are observed for amines (aniline, p-methylaniline (p-MA), p-chloroaniline (p-CA), and p-aminobenzoic acid (p-ABA)), phenols (phenol, p-chlorophenol (4-CP) Bisphenol A (BPA), 1-Naphthol (1-NP)), dyes (rhodamine B (RhB) and methyl orange (MO)), and metal ions (Pb2+, Hg2+, and Cd2+). The resulting polymers exhibited excellent adsorption performance towards these pollutants. Especially, the removal rate of aniline is above 95% in the concentration of 2.5 mg/L in 40 min at 25 °C. The interaction mechanism has been investigated, and confirmed by FTIR and the theoretical calculation results. It is due to surface complexation and chemisorption between adsorbent and adsorbate. The polymer exhibits good performance such as high adsorption capacity, high separation efficiency, biodegradable properties, and easy regeneration, suggesting that its potential technological applications for the removal of organic compounds and heavy metal ions from actual industrial effluent.

The limited availability of water resources worldwide presents obstacles, to the progress of ag-riculture. This situation calls for the implementation of water saving technologies to address these challenges effectively. The quest for technologies that conserve water in agriculture, par-ticularly within the context of cotton production, is related to the study of the impact of drought on the growth, leaf surface area, accumulation of dry matter, boll number, and productivity. The benefits of local drip irrigation have been established. Various models and strategies for opti-mizing and improving the efficiency of how we use water for irrigation purposes. In a market driven economy the effective utilization of water assetsis closely linked to the improvement of managing mineral nutrients. To enhance both the quantity and quality of production, nitrogen is the key factor element that plays a role in the process. The formation of highly efficient cotton crops by adapting the growing technology to the specific soil-climatic conditions of the area, in-cluding controlling nitrogen fertilizing and irrigation, is the primary method to achieve con-sistent harvests. The results of irrigation with water deficit and feeding plants with different fer-tilizer rates are presented. This matter is presently significant, in achieving dependable crop harvests supporting the economic growth of farms and safeguarding the well being of agricul-tural environments.

Nitrogen fertilization can provide greater nutritional support and mitigate salt stress in the millet crop. The aim of this study was to evaluate the physiological responses and agronomic performance of millet crops subjected to nitrogen fertilization and irrigation water salinity. The study was carried out in a greenhouse, using a completely randomized design in a 5 x 2 factorial scheme, with 4 rep-lications, with five doses of nitrogen (40; 60; 80; 100 and 120 kg ha-1 of N) and two levels of elec-trical conductivity of the irrigation water: 0.3 and 4.0 dS m-1. We concluded that salt stress in-creased leaf sodium levels and had a negative impact on stalk dry mass and panicle dry, leaf gas exchange, mineral element concentrations (K, P and Ca), and water use efficiency. The use of lower salinity water associated with increased nitrogen fertilization provides greater stalk dry mass and panicle dry, photosynthesis, water use efficiency, chlorophyll index, leaf potassium concentration, and biomass production. Salt stress negatively affected transpiration, stomatal conductance, leaf P and Ca levels, and increased leaf sodium levels as nitrogen fertilization increased in millet plants grown under pot conditions. These results can be used to create a strategy to reduce the negative impact of salt stress associated with the nutrition of millet plants, using nitrogen fertilization.

The residual content of the only carbon source increases at the end of the exponential growth phase when P. putida BS3701 cells are cultured under nitrogen deficiency. Moreover, the mRNA quantity of some genes involved in carbon catabolism decreases. There are no available data on regulators capable of stimulating the target mRNA degradation in pseudomonads under nitrogen deficiency in the literature. We have applied both comparative genomics methods and a number of biomolecular ones to identify new small P. putida BS3701 RNAs. This is due to the fact that the formation of ncRNA-mRNA duplexes, recognized by RNases, is one of the main mechanisms for reducing the number of transcripts in a cell. We have used the following selection criteria: 1) the presence of the interest gene of the NtrC binding site and a sigma54-dependent promoter in the upstream area, 2) the conservative location of the interest gene in the P. putida and P. aeruginosa genomes, 3) increase in the product quantity of the interest gene in a cell under nitrogen deficiency on two different carbon sources (succinate and naphthalene), 4) the product detection of the interest gene in a fraction enriched with small RNAs. The expression of two new small RNAs has increased twice or more times under nitrogen deficiency on both succinate and naphthalene: expression of ng171 and ng379. ng379 contains narK RNA motif.

CONTEXT: The sustained White corn (Zea mays L.) yield relies on supply of Nitrogen (N), which is an important element in improving soil fertility. OBJECTIVE: The research aim to determine the effect of Nitrogen on white corn yield and grain mass. METHOD: The experimental design was a 4 × 4 factorial arranged in randomized complete block design with 2 replications each. The effect of nitrogen was determined in terms of the flow within the soil, initial component, addition, uptake, loss and use of nitrogen by the White corn plants. Nitrogen was applied as Granular Urea using zero broadcast method. The grain yield was determined hand-harvesting and shelling. RESULTS AND CONCLUSIONS: There were no statistically significant differences between the mean samples from the two replicates (blocks 1 & 2) across the two seasons for corn sugar concentration, corn yield estimates and grain yields. In 2021, the mean yield estimate was 12,552 Kg ha-1, while that of 2022 averaged 12687 Kg ha-1. Similarly, the grain yield achieved in 2022 was 844.1kg more than the average grain yield in 2021. The white corn yield estimate and grain yield increased linearly with an increase in nitrogen application level, with the highest yields achieved when nitrogen fertilizer was applied at 150kg N/ha. This demonstrates that nitrogen has a positive influence on the yield quantity of white corn. SIGNIFICANCE: The White maize model may be used to improve the formulation of decisions and enhance the precision of estimates for yield and N fate within the soil-plant-atmosphere continuum. Further, the findings of this study can significantly enhance agricultural productivity while keeping an eye on the environment.

Chemical warfare agents (CWAs) are one of the most toxic compounds. Degradation of CWAs using decontamination agents is one of the few ways to protect human health against the harmful effects of CWAs. A ferrate Fe(VI) based potential chemical warfare agent decontaminant was studied for degradation of persistent nitrogen mustard (tris(2-chloroethyl)amine, HN3). By optimizing the reaction conditions, the complete degradation of HN3 was achieved in 4 minutes. The degradation products contained mostly reduced Fe species which confirmed the environmental friendliness of the proposed decontamination solution.

This research is mainly focused on the evaluation of TiO2/Fe2O3 composite and two industrial types of waste (kaolin (Clay-K) and a blast furnace sludge (BFS)) as adsorbent materials of cyanide and as photocatalysts. First, adsorption tests were performed in the absence of light. During photodegradation experiments, the effect of the type of irradiation (ultraviolet (UV) light), visible light and natural sunlight), irradiation time, the type of photocatalyst, as well as irradiance in case of natural sunlight use, were investigated. Adsorption results indicate that Clay-K and TiO2/Fe2O3 materials adsorb approximately twice as much cyanide compared to the BFS sample, which only adsorbs 33.3% (124.87 mg/g); this is due to its smaller specific surface area (5.69 m2/g) compared to that of the other two materials (Clay-K and TiO2/Fe2O3 (14.93 m2/g and 66.59 m2/g, respectively). The results obtained from the study of photodegradation of cyanide under UV irradiation, indicate that Clay-K and BFS samples photodegrade cyanide by 96.44% and 92.66%, respectively. On the other hand, using UV irradiation plus solar irradiation and visible plus solar irradiation, the best photocatalyst was the TiO2/Fe2O3, with 98.66% photodegradation. The use of natural sunlight (irradiance of 600 to 800 W/m2) of a NaCN solution of 750 mg/L, the BFS material was the most efficient to photodegrade cyanide, obtaining 97% in two hours and 87% in just 30 minutes of irradiation.

Wasted Green tuff powder produced by cutting Towada stone is recycled as environmental cleaning material. The optimum temperature for green tuff powder calcination to reduce the hydroxyl radical produced in hydrogen peroxide decomposition with ultraviolet light (UV) and no light. The green tuff calcined at 800 °C shows the large decomposition rate of hydrogen peroxide with no UV light when measured by using ESR. With UV light, the optimum temperature for calcinating the green tuff powder in order to reduce hydroxyl radical is also 800 °C. Next, the powder calcined at 800 °C is used to produce the tile by compression and heating, and then the formaldehyde adsorption rate was measured. The green tuff powder calcined at 800 °C showed a high adsorption rate, similar to that of the activated carbon. The tiles formed at 40 MPa and heated st 1100 °C were the strongest and also adsorbed formaldehyde. The adsorbed formaldehyde on the green tuff tile and powder might have a possibility to decompose by photocatalytic.

The capacity and the mechanism of the adsorption of aqueous barium (Ba), cobalt (Co), strontium (Sr) and zinc (Zn) by Ecuadorian (NatAllo) and synthetic (SynAllo-1 and SynAllo-2) allophanes were studied as a function of contact time, pH and metal ion concentration using kinetic and equilibrium experiments. The mineralogy, nano-structure and chemical composition of the allophanes were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and specific surface area analyses. The evolution of adsorption fitted to a pseudo-first-order reaction kinetics, where equilibrium between aqueous metal ions and allophane was reached within < 10 min. The metal ion removal efficiencies varied from 0.7 to 99.7 % at pH 4.0 to 8.5. At equilibrium, the adsorption behavior is better described by the Langmuir model than by the Dubinin-Radushkevich model, yielding sorption capacities of 10.6, 17.2 and 38.6 mg/g for Ba^(2+), 12.4, 19.3 and 29.0 mg/g for HCoO_2^-, 7.2, 15.9 and 34.4 mg/g for Sr^(2+) and 20.9, 26.9 and 36.9 mg/g for Zn^(2+), respectively, by NatAllo, SynAllo-2 and SynAllo-1. The uptake mechanism is based on a physical adsorption process. Allophane holds great potential to remove aqueous metal ions and could be used instead of zeolites, montmorillonite, carbonates and phosphates for wastewater treatment.